Polyolefin fibre reinforced concrete (PFRC) has become an attractive alternative to steel for the reinforcement of concrete elements mainly due to its chemical stability and the residual strengths that can be reached with lower weights. The use of polyolefin fibres can meet the requirements in the standards, although the main constitutive relations are based on the experience with steel fibres. Therefore, the structural contributions of the fibres should be assessed by inverse analysis. In this study, the fibre dosage has been fixed at 6kg/m³ and both self-compacting concrete and conventional concrete have been used to compare the influence of the positioning of the fibres. An idealized homogeneous distribution of the fibres with such fibres crossing from side to side of the specimen has been added to self-compacting concrete. The experimental results of three-point bending tests on notched specimens have been reproduced by using the cohesive crack approach. Hence, the constitutive relations were found. The significance of this research relies on the verification of the formulations found to build the constitutive relations. Moreover, with these results it is possible to establish the higher threshold of the performance of PFRC and the difficulties of limiting the first unloading branch typical of fracture tests of PFRC.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

Zinc protection of galvanized steel is initially dissolved in alkaline solutions. However, passive layer is formed over time which protects the steel from corrosion. The behavior of galvanized steel exposed to strong alkaline solutions (pH values of 12.7) with a fixed concentration of sulfate ion of 0.04M is studied. Electrochemical measurement techniques such as corrosion potential, linear polarization resistance and electrochemical impedance spectroscopy are used. Synergistic effect of sulfate ion is also studied together with other anions such as chloride Cl- or bicarbonate ion HCO3- and with other cations such as calcium Ca2+, ammonium NH4+ and magnesium Mg2+. Presence of sulfate ions can depassivate the steel, leading to corrosion density of 0.3 µA/cm2 at the end of the test. The presence of other ions in the solution increases this effect. The increase in corrosion density caused by cations and anions responds to the following order (greater to lesser influence): NH4+>Ca2+>Mg2+ and HCO3- >Cl- >SO42-.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Size effect on plain concrete specimens is well known and can be correctly captured when performing numerical simulations by using a well characterised softening function, but in the case of fibre reinforced concrete this is not directly applicable, since an only diagram cannot capture the material behaviour on elements with different size due to dependence of the orientation factor of the fibres with the size of the specimen. In previous works, the use of a trilinear softening diagram proved to be very convenient for reproducing fracture of polyolefin fibre reinforced concrete elements, but only if it is previously adapted for each specimen size. In this work, a predictive methodology is used to reproduce fracture of polyolefin fibre reinforced concrete specimens of different sizes under three-point bending. Fracture is reproduced by means of a well known embedded cohesive model, with a trilinear softening function that is defined specifically for each specimen size. The fundamental points of these softening functions are defined a priori by using empirical expressions proposed in past works, based on an extensive experimental background. Therefore, the numerical results are obtained in a predictive manner, and then compared with a previous experimental campaign, showing that this approach properly captures the size effect, although some values of the fundamental points in the trilinear diagram could be defined more accurately.

The determination of the parameters that characterise the air-void system in hardened concrete elements becomes crucial for structures under freezing and thawing cycles. The ASTM C457 standard describes some procedures to accomplish this task, but they are not easy to apply, require specialised equipment such as a stereoscopic microscope and result in highly tedious tasks to be performed. This paper describes an alternative procedure to the modified point-count method described in the Standard that makes use of macro photography. This alternative procedure is successfully applied to a large set of samples and presents some advantages over the traditional method, since the required equipment is less expensive and provides a more comfortable and less tedious procedure for the operator.

Fibre reinforced concrete (FRC) has been used for decades in certain applications of the construction industry, such as tunnel linings and precast elements, but has experienced an important progress in recent times, boosted by the inclusion of guidelines for their use in some national and international standards. Traditional steel fibres have been studied in depth and their performance is well known although in recent years new materials have been proposed as possible alternatives. Polyolefin macro-fibres, for instance, have proven to enhance the mechanical properties of concrete and the parameters that define their behaviour (fibre length, fibre proportion or casting method, for instance) have been identified. These fibres overcome certain traditional problems related to steel fibres, such as corrosion or their interaction with magnetic fields, which can limit the use of steel in some applications. The behaviour of polyolefin fibre reinforce concrete (PFRC) has been numerically reproduced with success through an embedded cohesive crack formulation that uses a trilinear softening diagram to describe the fracture behaviour of the material. Furthermore, concrete behaves well under high temperatures or fire events, especially when it is compared with other construction materials, but the behaviour of PFRC must be analysed if the use of these fibres is to be extended. To this end, the degradation of PFRC fracture properties has been recently experimentally analysed under a temperature range between 20ºC and 200ºC. As temperature increases, polyolefin fibres modify their mechanical properties and their shape, which reduce their performance as reinforcement of concrete. In this work, those experimental results, which include results of low (3 kg/m3) and high (10 kg/m3) proportion PFRC specimens, are used as reference to study the fracture behaviour of PFRC exposed to high temperatures from a numerical point of view. The experimental load-deflection diagrams are reproduced by modifying the trilinear diagram used in the cohesive model, which helps to understand how the trilinear diagram parameters are affected by high temperature exposure. Finally, some expressions are proposed to adapt the initial trilinear diagram (obtained with specimens not exposed to high temperature) in order to numerically reproduce the fracture behaviour of PFRC affected by high temperature exposure.

This paper describes the packaging models that are fundamental for the design of ultra-high-performance concrete (UHPC), and their evolution. They are divided into two large groups: continuous and discrete models. The latter are those that provide the best answer in obtaining an adequate simulation of the packing of the particles up to nanometric size. This includes the interaction among the particles by means of loosening and wall coefficients, allowing a simulation of the virtual and real compactness of such particles. In addition, a relationship between virtual and real compactness is obtained, through the compaction index, which may simulate the energy of compaction that the particles undergo in their placement in the mold. The use of last-generation additives allows such models to be implemented with water-cement (w/c) ratios close to 0.18. However, the premise of maximum packing as a basic pillar for the production of UHPC should not be the only one. The cement hydration process affected by nanoadditions and the ensuing effectiveness in the properties in both fresh and hardened state according to the respective percentages in the mixture should also be studied. An adequate ratio and proportion of these additions may lead to an obtaining of better results even with lower levels of compactness.

Concrete has become the most common construction material showing among other advantages good behaviour when subjected to high temperatures. Nevertheless, concrete is usually reinforced with elements of other materials such as steel in the form of rebars or fibres. Thus, the behaviour under high temperatures of these other materials can be critical for structural elements. In addition, concrete spalling occurs when concrete is subjected to high temperature due to internal pressures. Micro polypropylene fibres (PP) have shown to be effective for reducing such spalling although this type of fibres barely improve any of the mechanical properties of the element. Hence, a combination of PP with steel rebars or fibres can be effective for the structural design of elements exposed to high temperatures. New polyolefin fibres (PF) have become an alternative to steel fibres. PF meet the requirements of the standards to consider the contributions of the fibres in the structural design. However, there is a lack of evidence about the behaviour of PF and elements made of polyolefin fibre reinforced concrete (PFRC) subjected to high temperatures. Given that these polymer fibres would be melt above 250 °C, the behaviour in the intermediate temperatures was assessed in this study. Uni-axial tests on individual fibres and three-point bending tests of PFRC specimens were performed. The results have shown that the residual load-bearing capacity of the material is gradually lost up to 200 °C, though the PFRC showed structural performance up to 185°C.

This work proposes a novel methodology for the complete characterization of fiber reinforced concrete (FRC). The method includes bending tests of prismatic notched specimens, based on the Standards for FRC, tensile and pure shear tests. The values adopted by the standards for designing FRC are the obtained from bending tests, typically fR3, even for shear and pure tension loading. This paper shows that the remaining strength of FRC, supplied by the fibers, depends on the type of loading. In the case of shear and tensile loading the prescriptions of the standards may be unsafe. In this work, the remaining halves of specimens subjected to bending test are prepared and used for shear and tension tests. This means significant savings in specimen preparation and a greater amount of information for structural use of FRC. The results provide relevant information for the design of structural elements of FRC compared with the only use of data supplied by bending tests. In addition, a video-extensometry system was used to analyze the crack generation and cracking patterns. The video-extensometry applied to shear tests allowed the assessment of the sliding values and crack opening values at the crack discontinuity. These values may be quite relevant for the study of the FRC behavior when subjected to shear according to the shear-friction model theories.

The reinforcement of concrete by using polyolefin fibres may be considered in structural design to meet the requirements of the applicable code rules. In order to achieve a reliable use of such a composite material, use of full-scale real structures is needed. The conversion of lab testing data into real practice properties is challenging and significantly influenced by various aspects, among which the size effect is a key one. Given that the available literature does not report coinciding conclusions about such an effect on quasi-brittle materials reinforced with fibres, further research is justified. Therefore, this work studies the behaviour of notched beams with three proportional sizes by using self-compacting polyolefin reinforced concrete with a fibre volume fraction of 1.1%. Flexural testing was carried out according to the standard EN-14651, with the results revealing the existence of the size effect. In addition, a reduction of the residual strength identified in the larger specimens was observed in fracture surfaces with equal fibre content.

Fibre reinforced concrete (FRC) has become an alternative for structural applications due its outstanding mechanical properties. The appearance of new types of fibres and the fibre cocktails that can be configured mixing them has created FRC that clearly exceed the minimum mechanical properties required in the standards. Consequently, in order to take full advantage of the contribution of the fibres in construction projects, it is of great interest to have constitutive models that simulate the behaviour of the materials. This study aimed to simulate the fracture behaviour of five types of FRC, three with steel hooked fibres, one with a combination of two types of steel fibres and one with a combination of polyolefin fibres and two types of steel fibres, by means of an inverse analysis based on the cohesive crack approach. The results of the numerical simulations defined the softening functions of each FRC formulation and have pointed out the synergies that are created through use of fibre cocktails. The information obtained might suppose a remarkable advance for designers using high-performance FRC in structural elements.

In this work 144 reinforcing bars of high-ductility steel named B500SD were subjected to an accelerated corrosion treatment and then tested under tension at different loading speeds in order to assess the effect of corrosion on the ductility properties of the rebars. Results showed that the bars with a corrosion level as low as the one reducing the steel mass by 1% gave rise to a significant degradation on the ductility properties with strain-stress curves losing the yield plateau and behaving practically as cold deformed steel bars. This effect took place at every tested loading speed. Thus, the research significance relies on the assessment of the influence of the loading speed at which the tensile test is performed given that it affects the ductility properties of the reinforcement bars.

The effect of graphene oxide (GO) on mechanical strengths and durability of cement composites has been studied by preparing GO-modified cement mortars. Thermogravimetric analysis (TGA) and nuclear magnetic resonance (29Si MAS-NMR) were performed on the cement paste to research the influence of GO on the hydration process and chain structure of calcium-silicate-hydrate (C-S-H) gels. In addition, mechanical strength test, such as compressive and flexural, were performed on cement mortars. The addition of GO at 0.05 wt.% (by weight of cement) increased the compressive strength by 9.02% after 28 days. Furthermore, the flexural strength of cement mortars with 0.05 wt.% GO and superplasticizer (SP) after 7 and 28 days increased by 12.26% and 21.86%, respectively, compared with reference mortar. At the same time, the effect of GO proved to be more significant and effective in the durability tests, suggesting that GO can enhance the microstructure through hydration products to create a highly cross-linked micro structure.

In this work, the transport equations of ionic species in concrete are studied. First, the equations at the porescale are considered, which are then averaged over a representative elementary volume. The so obtained transport equations at the macroscopic scale are thoroughly examined and each term is interpreted. Furthermore, it is shown that the tortuosity-connectivity does not slow the average speed of the ionic species down. The transport equations in the representative elementary volume are then compared with the equations obtained in an equivalent pore. Lastly, comparing Darcy’s law and the Hagen-Poiseuille equation in a cylindrical equivalent pore, the tortuosity-connectivity parameter is obtained for four dierent concretes. The proposed model provides very good results when compared with the experimentally obtained chloride profiles for two additional concretes.

In 2007, the excavation of the M-30 ring road located in Madrid and the creation of a green corridor either side of the Manzanares river brought significant change to the metropolitan area. The corridor and linear park which it provided were designed to contribute to the regeneration of the fluvial ecosystem, establish links among residents on each side of the river and promote cultural and leisure activities. This paper provides a sustainability analysis of the excavation of the M-30 (involving the socio-economic and environmental impact) 14 years after its construction. In order to show such an impact, an analysis of the area both prior to the project and after completion, as well as a hypothetical solution that uses improved materials, has been performed. This entails use of the multi-criteria decision-making model named MIVES (initials in Spanish, modelo integrado de valor para una evaluación sostenible). The MIVES method is based on the application of value functions of sustainability indicators selected by socio-economic and environmental criteria, chosen by experts. Results from analysis showed that the excavation of the M-30 considerably improved the sustainability of the area (sustainable index 3.43 and 6.26 both before and after the excavation works). However, use of improved materials in contrast with the application of conventional materials slightly improved the sustainability of the work (Sustainability Index 6.26 and 6.74, respectively, of the conventional materials).

Construction involves the use of significant quantities of raw materials and entails high-energy consumption. For the sake of choosing the most appropriate solution that considers environmental and sustainable concepts, tools such as the integrated value model for sustainable assessment (Modelo Integrado de Valor para una Evaluación Sostenible, MIVES) used in Spain, plays a key role in obtaining the best solution. MIVES is a multi-criteria decision-making method based on the value function concept and the seminars delivered by experts. Such tools, in order to show how they may work, require application to case studies. In this paper, two concrete slabs manufactured with differing reinforcement during the construction of the La Canda Tunnels are compared by means of MIVES. The two concrete slabs were reinforced with a conventional steel-mesh and with polyolefin fibres. The results showed that from the point of view of sustainability, the use of polyolefin fibres provided a significant advantage mainly due to the lower maintenance required.

This paper analyses the evolution of the internal damage in two types of steel that show different fracture behaviours, with one of them being the initial material used for manufacturing prestressing steel wires, which shows a flat fracture surface perpendicular to the loading direction, and the other one being a standard steel used in reinforced concrete structures, which shows the typical cup-cone surface. 3mm-diameter cylindrical specimens are tested with a tensile test carried out in several loading stages and, after each of them, unloaded and analysed with X-ray tomography, which allows detection of internal damage throughout the tensile test. In the steel used for reinforcement, damage is developed progressively in the whole specimen, as predicted by Gurson-type models, while in the steel used for manufacturing prestressing steel-wire damage is developed only in the very last part of the test. In addition to the experimental study, a numerical analysis is carried out by means of the finite element method by using a Gurson model to reproduce the material behaviour.

In the context of Shared Autonomous Vehicles, the need to monitor the environment inside the car will be crucial. This article focuses on the application of deep learning algorithms to detect objects, namely lost/forgotten items to inform the passengers, and aggressive items to monitoring if violent actions may arise between passengers. For object detection algorithms was used public datasets (COCO and TAO) to train state-of-the-art algorithms, such as YOLOv5. For violent action detection was used the MoLa InCar dataset to train on state-of-the-art algorithms such as I3D, R(2+1)D, SlowFast, TSN and TSM. At the end an embedded automotive solution was used to demonstrate both methods running in real-time.

Concrete production requires a significant amount of natural resources, with aggregates comprising between 55% and 80% of the total volume. However, over-exploitation of natural aggregates has led to the exploration of alternative materials for use in concrete production. In this study, crushed hazelnut shells were investigated as a partial replacement for fine aggregate, addressing the problem of natural resource depletion and offering a second use for this important agricultural waste product available in Chile. Hazelnut shells were incorporated in percentages of 2.5%, 5%, and 10% by weight of sand for water-cement ratios of 0.4 and 0.5. The compressive strengths at 7 and 28 days and bending tensile strengths at 28 days were determined, alongside physical properties such as workability, temperature, air content, fresh density, and hardened density of the concrete. Our findings show that replacing 2.5% of the fine aggregate with hazelnut shells led to higher compressive strength at 28 days, exceeding the strength of the standard specimens by 9.5%, whereas replacing 5% of the fine aggregate led to the highest bending tensile strength, exceeding the resistance of the standard specimens by 3.5%. Moreover, the 0.4 w/c ratio consistently led to better results for both compressive and bending tensile resistances, with fewer and lower reductions in mechanical resistances compared to the standard mixture. Our results suggest that concrete mixes with hazelnut shells as a replacement for fine aggregate at a percentage of up to 2.5% can be used in constructive systems with compression strengths lower than 17 MPa, and mixtures with up to 10% hazelnut shell replacement can be used in structures with tensile bending stress requirements lower than 6 MPa. Overall, the use of hazelnut shells as a partial replacement for fine aggregate in concrete production presents an environmentally-friendly and cost-effective solution for the construction industry.

Fibre reinforced cementitious materials (FRC) have become an attractive alternative for structural applications. Among such FRC, steel and polyolefin fibre reinforced concrete and glass fibre reinforced concrete are the most used ones. However, in order to exploit the properties of such materials structural designers need constitutive relations that reproduce FRC fracture behaviour accurately. This contribution analyses the suitability of multilinear softening functions combined with a cohesive crack approach for reproducing the fracture behaviour of the FRC previously mentioned. The implementation performed accurately simulates the fracture behaviour while being versatile, robust and efficient from a numerical point of view.

The food distribution process is responsible for significant quality loss in perishable products. However, preserving quality is costly and consumes a tremendous amount of energy. To tackle the challenge of minimizing transportation costs and CO2 emissions while also maximizing product freshness, a novel multi-objective model is proposed. The model integrates a vehicle routing problem with temperature, shelf life, and energy consumption prediction models, thereby enhancing its accuracy. Non-dominated sorting genetic algorithm II is adapted to solve the proposed model for the set of Solomon test data. The conflicting nature of these objectives and the sensitivity of the model to shelf life and shipping container temperature settings are analyzed. The results show that optimizing freshness objective degrade the cost and the emission objectives, and the distribution of perishable foods are sensible to the shelf life of the perishable foods and temperature settings inside the container.

Steel fibers (SF) and polyolefin (PF) are widely used for shotcrete, especially in tunnelling. Both SF and PF and have shown to meet the standards in order to reduce or substitute the conventional steel mesh as reinforcement of concrete showing mechanical and productive advantages. This study sought the analysis and assessment of the mechanical properties of fiber reinforced shotcrete, comparing in-situ with laboratory results. This was performed with low and high fiber dosages of SF and PF as well as a combination of them (hybrid mixtures). A total of seven mixtures, two of steel, two of polyolefins, two hybrids and a control mixture were manufactured at laboratory and in situ. By performing tests according to EN 14651 and slabs according to EN 14488-5, it was possible to characterize the residual flexural strengths (fRj), and energy absorption capacity (E25mm) in slabs. In addition, a fracture surface analysis was performed, and the orientation factor was obtained. This allowed the authors to quantify the loss of residual strength on site and correlate it with the fiber content and positioning. Moreover, some relationships between beam and slab tests were found, allowing to correlate the most relevant type of tests in the field of fiber reinforced concrete.

Existence of hybrid electric vehicles nowadays is one of the emerging technologies worldwide. Different countries are using this technology on their transportation, and nowadays, a lot of other countries are gradually adapting on using this kind of innovation in their transport system. Philippines is among these countries which aims to have a sustainable mobility by embracing the use of hybrid - electric vehicles but still lots of consumers are lacking awareness on this technology. Lack of information on the social, environmental, and economic potential benefits are among the main issues of Philippines consumers that really affect its uptake. The goal of this study was to evaluate the consumer’s perception and purchase intention on the transition of hybrid - electric vehicles for sustainable mobility and transportation here in the Philippines. It aimed to assess consumer awareness with hybrid - electric vehicles and its potential benefits to human beings in terms of social, environmental, and economic aspects. The study also gauged the impact of this perception on consumer’s purchase intention on hybrid - electric vehicles. These objectives were attained using the Descriptive Statistics and Correlation Analysis. Using these methods, the results revealed that majority of the consumers believed on the positive benefits of transitioning to hybrid - electric vehicles in terms of social, environmental, and economic aspects. This study also showed that these benefits have high impact on the consumer’s intention of buying or having a hybrid – electric vehicle. Electric vehicle is one of the most effective measure of decarbonizing the transport system. Furthermore, government and automotive businesses must strengthen their drive in spreading awareness of hybrid – electric vehicle’s benefits to consumers to further support country’s effort for development.

Hepatitis C virus (HCV) is a major public health threat associated with serious clinical consequences worldwide. The WHO reports an estimated 58 million people globally living with chronic hepatitis C virus (HCV) infection, with 1.5 million new cases and over 350,000 deaths annually due to HCV-related diseases. Despite the existence of multiple diagnostic methods, the accessibility of diagnosis and treatment is often hindered across the continent by limited resources, insufficient healthcare infrastructure, and low public awareness of Hepatitis C virus Hepatitis C virus infection is a major public health concern in African countries, which have the highest prevalence rates of HCV in the world (1–26%). Egypt, African country which had the highest prevalence of Hepatitis C virus infection in the world. Its national hepatitis C elimination initiative emerges as an exemplary case of success an having screened over 60 million individuals, and treated more than 4 million, thereby markedly diminishing both the prevalence and incidence of the disease. The strategies employed by Egypt offer critical insights and adaptable frameworks for other African Countries facing analogous challenges. The Aim of this Review is to highlight the triumphs and hurdles of Egypt's approach, while also providing strategic guidance for African Countries to accelerate the journey towards the eradication of hepatitis C.

Fatty Acid Amide Hydrolase (FAAH) is one of the enzymes responsible of endocannabinoids metabolism. The inhibition of FAAH is a useful and indirect strategy to raise endogenous cannabinoid concentrations, which would be useful for the treatment of various pathological processes in which cannabinoid concentrations are lowered. In the present work, we present an extensive 3D-QSAR/CoMSIA study on a series of 90 irreversible inhibitors of FAAH of pyrimidinyl-piperazine-carboxamide structure. The final model obtained was extensively validated (q2 = 0.734; r2test = 0.966; r2m = 0.723), and based on the information derived from the contour maps we reported a series of 10 new compounds designed as powerful FAAH inhibitors (pIC50 of the best-proposed compounds = 12.196; 12.416).

The use of polyolefin fibre reinforced concrete (PFRC) as an alternative for reducing or even eliminating the reinforcing steel bars employed in reinforced concrete has become real in the past years. This contribution analyses the improvements in sustainability that a change in the aforementioned reinforcement configuration might provide in a flyover bridge. Economic, environmental and social parameters of both possibilities were studied by means of the integrated value model for sustainable assessment use (Modelo Integrado de Valor para una Evaluación Sostenible, MIVES) used in Spain, which is a multi-criteria decision-making method based on the value function concept and the seminars delivered by experts. The results of the MIVES method showed that the use of PFRC in combination with reinforced concrete (RC) has a sustainability index 22% higher. An analysis of the parameters that form this evaluation shows that there are no remarkable differences in the financial costs between the two possibilities studied. Nevertheless, social and environmental aspects provide with a better qualification the option of building a bridge by using PFRC combined with RC.

This work deals with the evaluation of adhesive single-lap joints using ultrasonic guided waves. An adhesive bonded lap joint can be modelled as a three-layer system made up of two adherents and an adhesive. The propagation of guided waves in the joint is developed from matrix formulations. The behavior of the different guided wave modes that propagate in the bonded region is characterized and it is found that their relative amplitudes can be estimated based on the properties of the incoming wave that propagates in the non-bonded region. It was verified that the excitation of these modes is ruled by the degree in which the shapes of both modes match each other. A 3D simulation of two aluminium bonded plates using 500 kHz ultrasonic transducers in a pitch and catch configuration was implemented using the Matlab k-Wave toolbox. Scattering effects due to some produced defects located in the bond line of the lap joints were simulated. Experimental setup with some artificial defects produced in the aluminum joints were used in order to compare with the simulated. Qualitative agreement was observed for the two approaches. The observed deviation can be due to the different characteristics of the experimental and simulated defects.

Copper-catalyzed and organocopper-involved reactions are of great significance in organic synthesis. To have a deep understanding of the reaction mechanisms, the structural characterizations of organocopper intermediates become indispensable. Meanwhile, the structure-function relationship of organocopper compounds would advance rational design and development of new Cu-based reactions and organocopper reagents. Compared to the mono-carbonic ligand, the C,N- and C,C-bidentate ligands better stabilize the unstable organocopper compounds. The bidentate ligands can chelate to the same copper atom via ?2-mode, forming a mono-cupra-cyclic compounds with at least one acute C-Cu-C angle. When the bidentate ligands bind to two copper atoms via ?1-mode at each coordinating site, the bimetallic macrocyclic compounds will form nearly linear C-Cu-C angles. The anionic coordinating sites of the bidentate ligand can also bridge two metals via ?2-mode, forming organocopper aggregates with Cu-Cu interactions and organocuprates with contact ion pair structures. The reaction chemistry of some selected organocopper compounds is highlighted, showing their unique structure-reactivity relationships.

Paenibacillus dendritiformis UJA2219 isolated from carrot produces broad-spectrum antibacterial activity. The aim of the present study was to determine the impact of partially-purified cell-culture extracts of strain UJA2219 on the microbial load and bacterial diversity of a home-made vegetable puree. The puree was challenged with an overnight culture of strain UJA2219 or with cultured broth extracts partially purified by cation exchange (CE) chromatog-raphy or reversed-phase (RP) chromatography and incubated for 7 days at temperatures of 4 °C or 25 °C. Best results were obtained at 25 °C with the RP extract, decreasing counts of presump-tive Enterobacteriaceae below detectable levels. The bacterial diversity of control and treated puree was studied by Illumina paired-end sequencing using DNA extracted from the puree samples incubated at 25 °C for 24 h. The controls and the puree inoculated with the UJA2219 strain showed an almost-identical bacterial diversity profile, with Proteobacteria (mainly Fam. Pseudo-monadaceae -gen. Pseudomonas- and Enterobacteriace as most abundant groups). Greatest differences in bacterial diversity were obtained in the puree treated with RP extract, showing a decrease in the relative abundance of Proteobacteria (especially gen. Pseudomonas) and an increase of Firmicutes (mainly of the genera Bacillus, Enterococcus and Lactococcus). Results from the study suggest that the antimicrobial preparations from strain UJA2219 have a potential for application in food bio-preservation.

β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of <1 μs, and density of 6.44 g/cm3. In this study, 2-inch diameter β-Ga2O3 single crystals were prepared by oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Academic publishing is undergoing a highly transformative process, and many rules and value systems that were in place for years are being challenged in unprecedented forms leading to the evolution of novel ways of dealing with new pressures. One of the most important aspects of an integrated and valid academic literature is the ability to screen publications for errors during peer review to weed out mistakes, fraud and inconsistencies, such that the final published product represents a product that has value, intellectually, and otherwise. It is difficult to claim the existence of perfect manuscripts. The level of errors that exist in a manuscript will depend on the rigor of the research group and of the peer review process that was used to screen that paper. When errors slip into a final published paper, either through honest error or misconduct, and are not detected during peer review and editorial screening, but are spotted during post-publication peer review, an opportunity is created to set the record straight, and to correct it. To date, the most common forms of correcting the literature have been errata, corrigenda, expressions of concern, and retractions. Despite this range of corrective measures, which represent artificially created corrals around pockets of imperfect literature, certain cases do not quite fit this mold, and new suggested measures for correcting the literature have been proposed, including manuscript versioning, amendments, partial retractions and retract and replace. In this commentary, a discussion of the evolving correction of the literature is provided, as are perspectives of the risks and benefits of such new measures to improve it.

Since the discovery of transposable elements (TEs) in Maize in the 1940s by Barbara McClintock [1] transposable elements have been described as junk, as selfish elements with no benefit to the host, and more recently as major determinants of genome structure and genome evolution. TEs are DNA sequences that are capable of moving to new sites in the genome and make additional copies while doing so. To limit the propagation of TEs, host silencing mechanisms are directed at transposon-encoded genes that are required for mobilization. The mutagenic properties of TEs, the potential of TEs to form new genes and affect gene expression, together with the host silencing mechanisms shape eukaryotic genomes and drive genome evolution. While TEs constitute more than half of the genome in many higher eukaryotes, transposable elements in the nematode C. ele-gans form a relatively small proportion of genome, about 15% [2]. Genetic studies of transposon silencing and the discovery of RNAi in C. elegans, propelled C. elegans to the forefront of studies of RNA-based mechanisms that silence TEs. Here, I will review the transposable elements that are present and active in the C. elegans genome, and the host defense mechanisms that silence these elements.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

In this paper, we present a new concept of the generalized core orthogonality (called the C-S orthogonality) for two generalized core invertible matrices $A$ and $B$. $A$ is said to be C-S orthogonal to $B$ if $A^{\tiny\textcircled{S}}B=0$ and $BA^{\tiny\textcircled{S}}=0$, where $A^{\tiny\textcircled{S}}$ is the generalized core inverse of $A$. The characterizations of C-S orthogonal matries and the C-S additivity are also provided. And the connection between the C-S orthogonality and C-S partial order has been given using their canonical form. Moreover, the concept of the strongly C-S orthogonality is defined and characterized.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

: For a long time, atherosclerosis has been regarded as a mere lipid deposit in the blood vessels. However, in the recent years a growing body of experimental and clinical evidence have highlighted the role of inflammation and immunity as a central mechanism of disease. Moreover, in the last decade the coming of next-generation sequencing and its application to large human population has broken the barrier between inflammation and cancer. Indeed, acquired mutation in key genes related to the control of hematopoiesis and myeloproliferation have paved the way to establish the new concept of clonal hematopoiesis of indeterminate potential. This phenomenon is being considered not such “indeterminate”, but as an emerging cardiovascular risk factor. Thus, this may explain the mechanisms of myeloproliferation and inflammation in atherosclerosis. And in a bidirectional journey, it has helped to explain the extremely high cardiovascular risk in cancer survivors, in particular in myeloprolfierative neoplasm patients. A deeper understanding of these mechanisms may pave the way for the future early diagnosis and potential preemptive treatments of the leading worldwide cause of death.

Artificial Intelligence (AI) has emerged as a disruptive technology in various areas, and medicine is no exception. In the last decade, there has been rapid progress in the application of AI in healthcare, from diagnosing and prognosticating diseases to improving operational efficiency in hospitals. This literature review explores the advances of artificial intelligence in the field of medicine, discusses its benefits, and discusses the ethical and regulatory challenges that need to be addressed to maximize its potential.

The COVID-19 pandemic crisis has brought about unprecedented economic and social consequences worldwide. The implementation of isolation measures, including national and international travel restrictions, significantly affected contact-intensive sectors such as tourism. During this lockdown period, Information and Communication Technology (ICT) was crucial in maintaining connectivity and enabling remote activities. Governments across the world implemented discretionary measures to mitigate the crisis's adverse effects on economic activity. This paper aims to analyze whether the level of ICT adoption and the importance of tourism influence the fiscal policy efforts pursued by governments. Based on the results of a linear regression analysis for 154 countries, the findings suggest that in countries with higher international tourism receipts, the governments had to promote higher fiscal stimulus. At the same time, ICT development diminished the efforts of the fiscal policy response to the crisis since it facilitated economic resilience. The findings of this study can contribute to understanding how governments responded to the pandemic crisis and the factors that influenced their fiscal policy decisions.

As synthetic/artificial life forms become more abundant and sophisticated, an increasing number of bizarre creatures - xenobots, robots, soft A-life entities, genetically engineered organisms, etc. - are invading our society. Therefore, we need to bring order to all this, to establish what is living and what is not. Here, I intend to classify all these non-natural entities and clarify their status with reference to their consideration or not as living beings, leaving the door open to an uncertain future in which perhaps we can see how "the artificial" and "the natural" merge to originate something new. To order all this "new biodiversity" and to also give entry to viruses (which are excluded of the three-domains tree of life), I propose the creation of a new domain, Lithbea (from the name: life-in-the-border entities), in which all these new human-made entities as well as the viruses will be included. Within this domain there would be two kingdoms, Virus and Humade (contraction of human-made), based on their origin, natural or human-made. A brief description of each component of Lithbea is included and the implications for society and biology of this “new biodiversity” is briefly discussed.

The ecosystem is an essential biological concept linking the living and the inanimate and represents the main structural and functional unit of nature. The biodiversity that exists on our planet can be organized into closely interconnected living worlds: acellular (viruses and capsidless genetic elements), prokaryotic (bacteria and archaea), and eukaryotic (all nucleated organisms). I want to highlight the presence of viruses as components of biodiversity because they are often overlooked in many studies despite their essential ecological and evolutionary role. Furthermore, I propose seven distinctive hallmarks that are inherent to any ecosystem: biodiversity, physical environment, hierarchy, interactivity, openness, “homecostasis”, and evolutionary. From the interaction and coupling of these living worlds with the environment (the environmental world), I define the ecosystem as a specific and dynamic ensemble of living and non-living worlds that functions as an open, hierarchical, and evolving system. This complex web of interactions that we call ecosystem can be graphically represented as a triangle reflecting the dynamic equilibrium between all the worlds. Finally, I propose a new way of graphically relating the ecosystem to biodiversity by taking the ecosystem as the nucleus from which all living worlds emerge.

What is life, what is the difference between something that is alive and something that is not, are viruses living beings, or what would life be like elsewhere in the universe, are questions that still do not have clear-cut answers fully accepted by the scientific community. Based on the fundamental attributes of all living things, I define life as a process that takes place in very ordered organic structures and is characterized by being automatic, interactive and evolutionary. I also define a living being as an organic, highly ordered, automatic, interacting and evolutionary system, and a robot as an ordered automatic and interacting system. Based on this definition and what we know about the biology of viruses, I maintain that they should be considered as living entities. Finally, I explain why if there were life elsewhere in the universe, it would be very similar to what we know on our planet.

We know that living matter must behave in accordance with the universal laws of physics and chemistry. However, these laws are insufficient to explain the specific characteristics of the vital phenomenon and, therefore, we need new principles, intrinsic to biology, which are the basis for developing a theoretical framework for understanding life. Here I propose what I call the seven commandments of life (the Vital Order, the Principle of Inexorability, the Central Dogma, the Tyranny of Time, the Evolutionary Imperative, the Conservative Rule, the Cooperating Thrust) as a set of principles that help us explain the vital phenomenon from an evolutionary perspective. In a metaphorical way, we can consider life like an endless race in which living beings are the runners, who are changing as the race goes on (the evolutionary process), and the commandments the rules.

This study introduces a Fiber Specklegram Sensor (FSS) design for temperature measurement utilizing a single-multi-single mode optical fiber configuration. FSS technology offers unique advantages for potential development into portable sensing systems. This investigation explores an FSS design compatible with miniaturization by optimizing the interrogation system based on the relationship between speckle grain size and filtering fiber area. Temperature variations are detected through fluctuations in optical power at the sensor output, offering a simple and reduced interrogation scheme. The performance of the FSS is assessed through post-calibration measurements compared to a commercial Fiber Bragg Grating (FBG) sensor, demonstrating comparable results. These findings pave the way for compact and portable fiber optic temperature sensing systems leveraging FSS advantages while maintaining compatibility with established fiber optic measurements.

In this study, we examine microscale waterflooding in a randomly close-packed porous medium. Three different porosities are prepared in a microfluidic platform and saturated with silicone oil. Optical video fluorescence microscopy is used to track the water front as it flows through the porous packed bed. The degree of water saturation is compared to water containing two different types of chemical modifiers, sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP), with water in the absence of a surfactant used as a control. Image analysis of our video data yield saturation curves and calculate fractal dimension, which we use to identify how morphology changes the way an invading water phase moves through the porous media. An inverse analysis based on the implicit pressure explicit saturation (IMPES) simulation technique uses mobility ratio as an adjustable parameter to fit our experimental saturation curves. The results from our inverse analysis combined with our image analysis show that this platform can be used to evaluate the effectiveness of surfactants or polymers as additives for enhancing the transport of water through an oil-saturated porous medium.

Recent developments, begun by the ascending spiral of the anticipated endless prospects of ChatGPT, promote artificial intelligence (AI) as an indispensable tool and commodity whose time has come. Yet the sinister specter of a technology that has hidden and unmanageable attributes that might be harmful to society looms in the background. As well as the likelihood that it will never deliver on the purported promise of artificial general intelligence (AGI). Currently the prospects for the development of AI and AGI are more a matter of opinion than based on a consistent methodological approach. Thus the need to take a step back to develop a general framework from which to evaluate current AI efforts, which also permits the determination of the limits to its future prospects as AGI. To gain insight into the development of a general framework, a key question that needs resolution is, what is the connection between human intelligence and machine intelligence? This is the question that needs a response because humans are at the center of AI creation and realize that without an understanding of how we become what we become, we have no chance of finding a solution. This work proposes infoautopoiesis, the self-referential, recursive and interactive process of self-production of information, as the needed general framework. Infoautopoiesis shows how the key ingredient of information is fundamental to an insightful resolution to this crucial question and allows predictions as to the present and future of AGI.

Let $\mathcal{N}$ be an arbitrary class of matroids, closed under isomorphism. For $k$ a positive integer, we say that $M \in \mathcal{N}$ is \emph{$k$-minor-irreducible} if $M$ has no minor $N \in \mathcal{N}$ such that $1\leq\left|E\left(M\right)\right|-\left|E\left(N\right)\right|\leq k $. Tutte's Wheels and Whirls Theorem establish that, up to isomorphism, there are only two families of 1-minor-irreducible matroids in the class of 3-connected matroids. More recently, Lemos classified the 3-minor-irreducibles with at least 14 elements in the class of triangle-free 3-connected matroids. Here we prove a local characterization for the 2-minor-irreducible matroids with at least 11 elements in the class of triangle-free 3-connected matroids. This local characterization is used to establish two new families of 2-minor-irreducible matroids in this class.

In patients with primary central nervous system lymphoma (PCNSL), the choice of surgical strategy for histopathologic assessment is still controversial, particularly in terms of preoperative corticosteroid (CS) therapy. To provide further evidence for clinical decision-making, we retrospectively analyzed data from 148 consecutive patients who underwent surgery at our institution. Although patients treated with corticosteroids preoperatively were significantly more likely to require a second or third biopsy (p=0.049), it was only necessary in less than 10% of the cases with preoperative corticosteroid treatment. The choice of surgical procedure did not affect diagnostic accuracy (p>0.05). Preoperative CSF sampling did not provide additional information but was associated with delayed surgery (p=0.02). Surprisingly, diagnostic accuracy was significantly lower when patients were treated with anticoagulation or dual antiplatelet therapy (p=0.015). In conclusion, preoperative CS therapy can challenge the histological diagnosis of PCNSL. At the same time, our data suggest that preoperative CS treatment only presents a relative contraindication for an early surgical intervention. The standard surgical approach is stereotactic biopsy, but other approaches can be individually considered. If a definitive diagnosis cannot be made after the first surgical intervention, the timing of a repeat biopsy after discontinuation of CS remains a case-by-case decision.

High concentrations of Na⁺ or [Co(NH₃)₆]³⁺ can induce the B to Z conformational transition in alternating (dC-dG) oligo and polynucleotides. The use of short DNA oligomers (dC-dG)₄ and (dm⁵C-dG)₄ as models can allow a thermodynamic characterization of the transition. Both form right handed double helical structures (B-DNA) in standard phosphate buffer with 115 mM Na⁺ at 25 ^oC. However, at 2.0 M Na⁺ or 200 mM [Co(NH₃)₆]³⁺, (dm⁵C-dG)₄ assumes a left handed double helical structure (Z-DNA) while the unmethylated (dC-dG)₄ analogue remains right handed under those conditions. We have previously demonstrated that the enthalpy of the transition at 25 ^oC for either inducer can be determined using isothermal titration calorimetry (ITC) [Ferreira, J. M. & Sheardy, R. D., Biophys. J. 2006, 91, 1–7]. Here, ITC is used to investigate the linkages between temperature, water activity and DNA conformation. We found that the determined enthalpy for each titration varied linearly with temperature allowing determination of the heat capacity change (DC_p) between the initial and final states. As expected, the DC_p values were dependent upon the cation (i.e. Na⁺ vs [Co(NH₃)₆]³⁺) as well as the sequence of the DNA oligomer (i. e., methylated vs unmethylated). Osmotic stress experiments were carried out to determine the gain or loss of water by the oligomer induced by the titration. The results are discussed in terms of solvent accessible surface areas, electrostatic interactions and the role of water.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

A 52-y/o asymptomatic male with history of hypertension, was referred to our Heart Failure Clinic due to report of hypertrophic cardiomyopathy, TTE with an increased end-diastolic thick-ness (basal inferoseptal of 23 mm, and basal anteroseptal of 21 mm). CMR demonstrated late gadolinium enhancement at the septum, anterior, inferolateral, and inferior walls with a mid-myocardial distribution, T1 mapping which reported an average T1 of 929 ms. A next-generation sequencing panel was requested. Results demonstrated hemizygosis, in the ga-lactosidase alpha gene, consistent with Fabry Disease. The replacement of the enzyme was start-ed. Extended familial genetic counseling and testing were done.

A mild, efficient, and photocatalytic synthesis of 6-phosphorylated phenanthridines via tandem radical addition/cyclization/aromatization of 2-isocyanobiphenyls with diarylphosphine oxides is reported. The method features operational simplicity, metal-free conditions, using low-cost rose Bengal as catalyst and sustainable air as terminal oxidant at room temperature, and providing the desired products in moderate to good yields.

Heart failure (HF) is a growing issue in developed countries and most patients present with a reduced ejection fraction. This condition significantly impairs quality of life and represents a threat not only for patients, but also for the entire healthcare system due to its high management cost. In the last decade, new medical treatments and devices have been developed to reduce HF hospitalizations and improve prognosis, while reducing the overall mortality rate. Medical therapy does not achieve the same results in all patients and, whenever it fails, technology comes in handy: novel devices for the management of HF have reduced symptoms. They have also improved the treatment of fluid retention and life threatening arrhythmias. The present review article gives to the readers a comprehensive overview of the most recent and important findings that need to be considered in HF with reduced ejection fraction patients. Both novel medical treatments and devices have been presented and discussed.

Two polyurethanes (PUs) were similarly synthesized by reacting a cycloaliphatic isocyanate with 1,4 butanediol and two polyols of different nature (polyester, polycarbonate diol) with molecular weights of 1000 Da. The PU made with polycarbonate diol polyol (YCD) was the only showing intrinsic self-healing at 20 °C. For assessing the mechanism of intrinsic self-healing of YCD, a structural characterization by molecular weights determination, infrared and X-ray photoelectronic spectroscopies, differential scanning calorimetry, X-ray diffraction, thermal gravimetric analysis and dynamic mechanical thermal analysis was carried out. It was concluded that the self-healing at 20 °C of YCD was due to non-covalent dynamic exchange interactions among the carbonate groups of the soft segments. Therefore, the chemical nature of the polyol played a key role in developing PUs with intrinsic self-healing at 20 °C.

Negative temperature coefficient (NTC) materials are usually based on ceramic semiconductors and electrons are involved in their transport mechanism. A new type of NTC material, adequate for alternating current (AC) applications, is represented by zeolites. Indeed, zeolites are single-charge carrier ionic conductors with a temperature-dependent electrical conductivity. In particular, electrical transport in zeolites is due to the monovalent charge-balancing cations, like K⁺, capable of hopping between negatively charged sites in the aluminosilicate framework. Owing to the highly non-linear electrical behavior of the traditional electronic NTC materials, the possibility to have alternative types of materials, showing linearity in the electrical behavior, is very desirable. Among different zeolites, the natural clinoptilolite has been selected for investigating the NTC behavior since it is characterized by high zeolite content, convenient Si/Al atomic ratio, good mechanical strength, due to its compact microstructure, and low toxicity. Clinoptilolite has shown a rapid and quite reversible impedance change under heating, characterized by a linear dependence on temperature. X-ray diffraction (XRD) has been used to identify the natural zeolite, to establish all types of crystalline phases present in the mineral, and to investigate the thermal stability of these phases up to 150°C. X-ray photoelectron spectroscopy (XPS) analysis has been used for the chemical characterization of the natural clinoptilolite sample, providing important information on the cationic content and framework composition. In addition, since electrical transport takes place in the zeolite free-volume, a Brunauer–Emmett–Teller (BET) analysis of the mineral has been also performed.

Non-alcoholic fatty liver disease (NAFLD), a frequent complication of metabolic syndrome and visceral obesity, is characterized by marked accumulation of lipids in hepatocytes, accompanied by oxidant stress. In a substantial minority of cases, this progresses to steatohepatitis, which in turn can lead to life-threatening hepatic fibrosis and/or hepatocarcinogenesis. This essay analyzes the molecular biology underlying fat accumulation and oxidant stress in NAFLD, and identifies targets that can be addressed by nutraceutical or dietary measures. Nutraceuticals with potential for prevention or control of NAFLD – as suggested on theoretical grounds, and borne out by experience in rodent studies and/or clinical trials - include ferulic acid, melatonin, methylnicotinamide, tetrahydrocurcumin, nicotinamide riboside, carnosic acid, urolithin A, quercetin, high-dose biotin, citrulline, astaxanthin, long-chain omega-3 fatty acids, berberine, lipoic acid, silibinin, N-acetylcysteine, taurine, capsaicin, spermidine, spirulina, and carnitine. Some of these agents can also address the NLRP3 inflammasome activation and transforming growth factor-β signaling that play a role in driving the transition to steatohepatitis and fibrosis. In addition, soy isoflavones, via estrogen receptor-beta agonism, have anti-fibrotic potential, and supplemental glycine may blunt the contribution of Kupffer cells to the progression of NAFLD. Whole-food plant-based diets of modest protein content, owing to their impact on hormones such as fibroblast growth factor 21 and adiponectin, as well as on the obesity and metabolic syndrome underlying NAFLD, may also be protective in this syndrome. There is considerable potential for complex medical foods or nutraceutical supplementation regimens of rational design to aid prevention and control of NAFLD.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

Live video streaming has become one of the main multimedia trends in networks in recent years. Providing Quality of Service (QoS) during live transmissions becomes a challenge due to the stringent requirements for low latency and minimal interruptions. This scenario has led to a high dependence on cloud services, implying a widespread usage of Internet connections, which constrains contexts where an Internet connection is not available. Thus, alternatives such as Mobile Ad Hoc Networks (MANETs) emerge as potential communication techniques. These networks operate autonomously with mobile devices serving as nodes, without the need for coordinating centralized components. However, these characteristics lead to challenges to live-video streaming, such as dynamic node topologies or periods of disconnection. Considering these constraints, this paper investigates the application of Artificial Intelligence (AI)-based classification techniques to provide adaptive streaming in MANETs. For this, a software-driven architecture is proposed to route stream in offline MANETs, predicting the stability of individual links and compressing video frames accordingly. The proposal has been implemented and assessed in a laboratory context, analyzing the model performance and QoS metrics. As a result, the model is implemented in a decision forest algorithm, which provides 95.9% of accuracy. Also, obtained latency values become assumable for video streaming, manifesting a reliable response for routing and node movements.

Rangelands are a key resource present all over the world as it covers half of emerged lands. They are even more important in drylands, where they cover 48% of the total area. Intensification and the additional pressure added by climate change push these systems towards desertification. Over the last two decades, we have developed and applied System Dynamics (SD) models for the study of Mediterranean grasslands. In addition, we have developed procedures and analysis tools, such as global sensitivity analysis, stability analysis condition, or risk analysis, in order to detect the main drivers of these socio-ecological systems and provide indicators about their long-term sustainability. This paper reviews these works, their scientific background, and the most relevant conclusions, including purely technical and rangeland-related ones as well as our experience as systemic modelers in a world driven by field specialists.

In this paper a more flexible extension of the Fréchet distribution is introduced. The new distribution is defined by means of the stochastic representation as the quotient of two independent random variables, a Fréchet distribution and the power of a random variable with uniform distribution in the interval (0,1). We will call this new extension the Slash Fréchet distribution and one of its main characteristics is that its tails are heavier than the Fréchet distribution. The general density of this distribution and some basic properties are determined. Its moments, skewness coefficients and kurtosis are calculated. In addition, the estimation of the model parameters is obtained by the method of moments and maximum likelihood. Finally, two applications with real data are performed by fitting the new model and comparing it with the Fréchet distribution.

The positional cloning of single nucleotide polymorphisms (SNPs) of the neutrophil cytosolic factor 1 (Ncf1) gene, advocating that a low oxidative burst drives autoimmune disease, demands an understanding of the underlying molecular causes. A cellular target could be T cells, which have been shown to be regulated by reactive oxygen species (ROS). However, the pathways by which ROS mediate T cell signaling remain unclear. The adaptor molecule linker for activation of T cells (LAT) is essential for coupling T cell receptor-mediated antigen recognition to downstream responses, and it contains several cysteine residues that have previously been suggested to be involved in redox regulation. To address the possibility that ROS regulate T cell-dependent inflammation through LAT, we established a mouse strain with cysteine-to-serine mutations at positions 120 and 172 (LATSS). We found that redox regulation of LAT through C120 and C172 mediate its localization and phosphorylation. LATSS mice had reduced numbers of double-positive thymocytes and naïve peripheral T cells. Importantly, redox insensitivity of LAT enhanced T cell-dependent autoimmune inflammation in collagen-induced arthritis (CIA), a mouse model of rheumatoid arthritis (RA). This effect was reversed on an NCF1-mutated (NCF1m1j), ROS-deficient, background. Overall, our data shows that LAT is redox-regulated, acts to repress T cell activation, and is targeted by ROS induced by NCF1 in antigen-presenting cells (APCs).

Landscape changes based on spectral responses allow showing plant cover changes through diversity, composition, and ecological connectivity. The spatial and temporal vegetation dynamics of the Bijagual Massif from 1986 to 2021 were analyzed as a measure of ecological integrity, conservation, and territory. The covers identified were high open forest (Hof), dense grassland of non-wooded mainland (Dgnm), a mosaic of pastures and crops (Mpc), lagoons (Lag), and bare and degraded lands (Bdl). The Bijagual Massif has 8,574.1 ha. In 1986, Dgnm occupied 42.6% of the total area, followed by Mpc (32.8%) and Hof (24.5%); by 2000, Mpc and Hof increased (43.7 and 28.1%, respectively), while Dgnm decreased (28%); by 2021, Dgnm was restricted to the northeastern zone and continued to decrease (25.2%), Mpc occupied 52.9%, Hof 21.7% and Bdl 0.1%. Of the three fractions of the connectivity probability index, only dPCintra and dPCflux contribute to ecological connectivity. Hof and Dgnm show patches with biota habitat quality and availability. Between 1986 and 2021, Dgnm lost 1,489 ha (41%) and Hof 239.5 ha (11%). Mpc replaced various covers (1,722.2 ha; 38%) in 2021. Bijagual has a valuable biodiversity potential limited by Mpc. Territorial planning and sustainable agroecological and ecotourism proposals are required due to the context of the ecosystems.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

Background: Permanent Daylight Savings Time (DST) may improve road safety by providing more daylight in the evening but could merely shift risk to morning commutes or increase risk due to fatigue and circadian misalignment. Methods: To identify how potential daylight exposure and fatigue risk could differ between permanent DST versus permanent Standard Time (ST) or current time arrangements (CTA), generic work and school schedules in five United States cities were modeled in SAFTE-FAST biomathematical modeling software. Commute data were categorized by morning (0700-0900) and evening (1600-1800) rush hours. Results: Percent darkness was greater under DST compared to ST for the total waking day (t=2.59, p=0.03) and sleep periods (t=2.46, p=0.045). Waketimes occurred before sunrise 63%±41% percent of the time under DST compared to CTA (42%±37%) or ST (33%±38%; F(2, 74)=76.37; p<0.001). Percent darkness was greater during morning (16%±31%) and lower during evening rush hour (0%±0%) in DST compare to either CTA (morning:7%±23%; evening:7%±14%) or ST (morning:7%±23%; evening:7%±15%). Discussion: Morning rush hour overlapped with students’ commutes and shift worker reverse commutes, which may increase traffic congestion and risk compared to evening rush hour. Switching to permanent DST may be more disruptive than either switching to ST or keeping CTA without noticeable benefit to fatigue or potential daylight exposure.

In recent years the yield of fruits and vegetables have been decreasing in Colombia, threatening national food security. Analysis of crop production data may lead to identifying cropping systems that have shown better adaptability to changes in climatic and non-climatic factors associated with agricultural production. The open database AGRONET keeps data of the agricultural activities conducted in Colombia, allowing to find the information organized by crops, regions and years; each row of the database registers farm information in Colombia. Aiming to identify resilient crops systems, agricultural data of fruits and vegetables were analyzed. First, trends in crop production were studied by year and locations, detecting the regions and crops with highest yields in the period from 2006 until 2020. Then, mixed linear regression and principal components analysis were applied to elucidate the relation between non-climatic factors and crop yield. In Colombia, vegetable production was more efficient than fruits, observing yields of 10.23 and 13.33 t ha^-1, respectively. On the other hand, the Colombian central region showed high yields for vegetables, while for fruits this was exhibited in northern and eastern locations. In the present study, yield variation responded to changes in the location of crop systems, while years had no effect on vegetable production. Furthermore, the price of the agricultural product and the cost of fertilizers were associated with the yield of the analyzed crops systems. In Colombia, carrot, cabbage, tomato papaya and pineapple are resilient crops whose yield increases especially by the regions where they are cultivated.

The performance of the presurgical test (preSurg) for temporal lobe epilepsy (TLE) was evaluated via video-electroencephalography (VEEG), electroencephalography (EEG), 99mTc-HmPAO single-photon emission tomography (SPECT) and 1.5 T magnetic resonance imaging (MRI) in a group of 112 men (37.0 ± 1.1 years) and 106 women (39.7 ± 1.1 years) operated on for TLE. The epileptic zone (EZ) was adequately identified to determine whether the patient reached an Engel I grade (EI) at least one year postop. Accuracy was evaluated by the coefficient α, ranging from 3 (when result = EZ) to 2 (result in the same hemisphere as the EZ), 1 (noninformative result) or 0 (EZ in the contralateral hemisphere). The simplicity of diagnosis was defined as the number of preSurg surgeries needed to identify the EZ. EI was obtained in 85.8% of patients even though 42.2% of patients had noninformative MRI results. For preSurg α was (mean ± SEM) = VEEG (2.83 ± 0.04) &gt; MRI (2.14 ± 0.08) &gt; EEG (1.87 ± 0.09) &gt; SPECT (1.71 ± 0.09). The accuracy (combination of sensitivity and specificity) was calculated as follows: VEEG (0.797) &gt; MRI (0.518) &gt; EEG (0.446) &gt; SPECT (0.360). The likelihood positive ratio was greater, and the likelihood negative ratio was lower for VEEG. The most relevant factor for the regression model was VEEG (3.106) &gt; MRI (2.558) &gt; EEG (1.905), and the factors were not significantly related to SPECT. EZs in EI patients with low simplicity were identified mainly by VEEG. A very good postoperative outcome can be obtained even in TLE patients with no lesions on MRI. The VEEG is the most reliable preSurg test and may be the only reliable test for patients with very low simplicity (i.e., difficult).single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: Place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: briefly describe the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article and it must not contain results that are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The α(1,2)fucosyltransferase (Se enzyme) encoded by FUT2 is involved in the secretor status of ABH(O) blood group antigens. The sedel2 allele is one of the non-functional FUT2 (se) alleles in which 9.3 kb containing the entire coding region of FUT2 is deleted by Alu-mediated nonhomologous recombination. In addition to this allele, three SNPs of FUT2, c.375A>G, c.385A>T, and c.571C>T, appear to be prevalent in certain Oceanian populations such as Polynesians. Recently, we developed an endpoint genotyping assay to determine the sedel2 zygosity, using a FAM-labeled probe for detection of the sedel2 allele and a VIC-labeled probe for detection of FUT2. In this study, instead of the VIC probe, a HEX-labeled probe covering both c.375A>G and c.385A>T and a Cy5-labeled probe covering c.571C>T were added to the sedel2 allele assay mixture to allow simultaneous detection of these four variations by endpoint genotyping for the sedel2 zygosity and fluorescence melting curve analysis for c.375A>G, c.385A>T, and c.571C>T genotyping. The results obtained from 24 Samoan subjects with this method were identical to those obtained with previous methods. Therefore, it appears that present method can accurately determine these four variations simultaneously.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

A series of dinuclear copper(I) N,C,N- and P,C,P-carbodiphosphorane (CDP) complexes using multidentate ligands CDP(Py)2 (1) and (CDP(CH2PPh2)2 (13) have been isolated and characterized. Detailed structural information was gained by single crystal XRD analyses of nine representative examples. The common structural motive is the central double ylidic carbon atom with its characteristic two lone-pairs involved into binding of two geminal L-Cu(I) fragments at Cu-Cu distances in the range 2.55 – 2.67 Å. In order to enhance conformational rigidity within the characteristic Cu-C-Cu triangle, two types of chelating side arms were symmetrically attached to each phosphorus atom: two 2-pyridyl functions in ligand CDP(Py)2 (1) and its dinuclear copper complexes 2-9 and 11, as well as two diphenylphosphinomethylene functions in ligand CDP(CH2PPh2)2 (13) and its di- and mononuclear complexes 14-18. Neutral complexes were typically obtained via reaction of 1 with Cu(I) species CuCl, CuI, and CuSPh or via salt elimination reaction of [(CuCl)2(CDP(Py)2] (2) with sodium carbazolate. Cationic Cu(I) complexes were prepared upon treating 1 with two equivalents of [Cu(NCMe)4]PF6, followed by the addition of either two equivalent of an aryl phosphine (PPh3, P(C6H4OMe)3) or one equivalent of a bisphosphine ligands DPEPhos, XantPhos or dppf. For the first time carbodiphosphorane CDP(CH2PPh2)2 (13) could be isolated upon treating its precursor [CH(dppm)2]Cl (12) with NaNH2 in liquid NH3. A protonated and a deprotonated derivative of ligand 13 were prepared and their coordination was compared to neutral CDP ligand 13. NMR analysis and DFT calculations reveal, that the most stable tautomer of 13 does not show a CDP (or carbone) structure in its uncoordinated base form. For most of the prepared complexes, photoluminescence upon irradiation with UV light at room temperature was observed. Quantum yields (PL) were determined to 36% for dicationic [(CuPPh3)2(CDP(Py)2)](PF6)2 (4) and to 60% for neutral [(CuSPh)2(CDP(CH2PPh2)2] (16).

In this paper, several two-dimensional clustering scenarios are given. In those scenarios, soft partitioning clustering algorithms (Fuzzy C-means (FCM) and Possibilistic c-means (PCM)) are applied. Afterward, VAT is used to investigate the clustering tendency visually, and then in order of checking cluster validation, three types of indices (e.g., PC, DI, and DBI) were used. After observing the clustering algorithms, it was evident that each of them has its limitations; however, PCM is more robust to noise than FCM as in case of FCM a noise point has to be considered as a member of any of the cluster.

DNA Topoisomerase IIa (Top2A) is a nuclear enzyme that is a cancer drug target, and there is interest in identifying novel sites on the enzyme to inhibit cancer cells more selectively and to reduce off-target toxicity. The C-terminal domain (CTD) is one potential target, but it is an intrinsically disordered domain, which prevents structural analysis. Therefore, we set out to analyze the sequence of Top2A from 105 species using bioinformatic analysis including the PSICalc algorithm, entropy analysis, and other approaches. Our results demonstrate that large (10th-order) interdependent clusters are found including non-proximal positions across the major domains of Top2A. Further, CTD-specific clusters of 3rd, 4th, and 5th-order were identified that included positions that had been previously analyzed via mutation and biochemical assays. Some of these clusters coincided with positions that when mutated either increased or decreased relaxation activity. Finally, sites of low entropy (i.e., high information content) were identified and mapped as key positions in the CTD. Included in the low entropy sites are phosphorylation sites and charged positions. Together, these results help to build a clearer picture of the critical positions in the CTD and provide potential sites/regions for further analysis.

Using a safe subset of C++ is a promising direction for increasing the safety of the programming language while maintaining its performance and productivity. In this paper, we examine how close existing C/C++ code is to conforming to a safe subset of C++. We examine the rules presented in existing safe C++ standards and safe C++ subsets. We analyze the code characteristics of 5.8 million code samples from the Exebench benchmark suite and 5 modern C++ applications using a static analysis tool. We find that raw pointers, unsafe casts, and unsafe library functions are used in both C++ code at large and modern C++ applications. In general, C++ code at large does not differ much from modern C++ code, and continued work will be required to transition from existing C/C++ code to a safe subset of C++.

Bone cement, mainly based in PMMA, is commonly used in different arthroplasty surgical proce-dures, and its use is essential for prosthesis fixation. However, its manufacturing process reaches high temperatures that can produce necrosis in the patients' surrounding tissues. In order to con-tribute to avoid this problem, the addition of graphene could delay the polymerisation of the MMA and, simultaneously, contribute to the optimisation of the composite material's properties. This article analysed the effect of the addition of different percentages of Highly Reduced Graphene Oxide (HRGO) with different wt. % (0,10, 0,50 and 1,00) and surface densities (150, 300, 500 and 750 m2/g) on the physical, mechanical, and thermal properties of commercial PMMA-based bone cement and its processing. It was noticed that a lower sintering temperature would be reached with this addition, making it less harmful to use in surgery and as it reduces its adverse effects. In contrast, the materials' density does not show significant changes, which indicates that the addi-tion of HRGO does not significantly increase its porosity. Lastly, the mechanical properties are re-duced by almost 20 %. Nevertheless, these properties are high enough so that these new materials can still fulfil their structural function.

The escalating environmental challenges that stem from urban residential waste in densely populated areas have become increasingly prominent in recent times. As a result, the waste management sector has experienced significant growth nationwide. However, due to the predominantly manual nature of these processes, their effectiveness falls short of meeting the current demand. Addressing these issues requires process enhancement. In this context, Industry 4.0, particularly the concept of Digital Twins, emerges as a potential avenue for refining processes. To tackle both current and future industry challenges, it is imperative to create a comprehensive methodology capable of generating effective solutions within the waste management sector. This paper provides an explanation of digital twins, outlines the methodological framework comprising an architectural structure and layered model, and details a series of sequential methodical stages for implementing digital twins based on the specific scope determined by the end-user. A noteworthy aspect is the transformative potential of digital twins in enhancing efficiency and precision within waste management practices. By providing a virtual real-time representation of the waste management system, digital twins empower simulations and experimentation to fine-tune processes. Furthermore, they facilitate informed decision-making by offering a detailed visualization of the complete system, simplifying the identification of challenges and opportunities for improvement. that this article derives from the presentation titled "Digital Twin application methodology for the improvement of production and service systems. Application to waste management processes" at the "Sustainable Smart Cities and Territories International Conference" held in the city of Manizales, Colombia, from 21st to 23rd June 2023.

Different types of gold nanoparticles have been synthesized that great potential in medical applications such as medical imaging, bio-analytical sensing and photothermal therapy. However, their stability, polydispersity and biocompatibility are major issues of concern. For example, the synthesis of gold nanorods, obtained through the elongated micelle process, produce them with a high positive surface charge that is cytotoxic. While gold nanoshells are unstable and within a few weeks they decompose due to Ostwald ripening. In this work, we report the self-assembly of the capsid protein of cowpea chlorotic mottle virus (CCMV) around spherical gold nanoparticles, gold nanorods and gold nanoshells to form virus-like particles (VLPs). All gold nanoparticles were synthesized or treated to give them a negative surface charge, so they can interact with the positive N-terminus of the capsid protein leading to the formation of the VLPs. To induce the protein self-assembly around the negative gold nanoparticles, we use different pH and ionic strength conditions that were determined from the capsid protein phase diagram. The encapsidation with the viral capsid protein confers them better biocompatibility, stability, monodispersity and a new biological substrate on which one can introduce specific ligands towards particular cells, broadening the possibilities of medical application.

Weight loss solutions are on the rise, and there is growing interest in natural alternatives to the pharmaceuticals in the market, which are not devoid of relevant side effects. To this end, the objective of the current study is to assess the effects of a botanical-based blend comprised of lemon verbena and hibiscus extracts in weight management, body fat, appetite, lipid, and glucose profiles, in an overweight population, for 90 days. As a result, the volunteers presented significant weight loss in absence of diet, which coincided with decreased body fat. Body fat was assessed by anthropometry, electrical bioimpedance and DEXA scan. Cholesterol levels were also significantly decreased. Satiety assessment revealed that the product contributed to increased feeling of fullness and satisfaction after a meal, compared to the placebo group, which could contribute to the weight loss observed. Blood glucose and blood pressure levels remained unchanged, which was expected as the volunteers were normoglycemic and their blood pressure was in the healthy range. In conclusion, daily supplementation of a botanical-based blend contributes to weight loss in overweight individuals, in absence of diet, while not affecting other parameters that are in the healthy range. This product could be a candidate alternative or add-on to other weight loss products, as part of a healthy lifestyle.

Keyhole neurosurgery implies reaching a target area inside the brain through an entry point specified by the neurosurgeon. In order to avoid complications, a risk assessment procedure must be done to establish the minimum risk trajectory from the entry point to the target area. The neurosurgeon establishes the risk values for the brain structure according to the type of intervention. The preset brain structure risk value is used to assess the risk value for each voxel of the brain. This paper proposes an improved risk assessment methodology based on the sum of N maximum risk values for each voxel. Then, risk assessment for a trajectory is done by adding the risk of all voxels that are part of the path. The safest trajectory is defined as the trajectory with the lower risk. Our proposed search trajectory methodology includes a Genetic Algorithm (GA) for finding the safest trajectories. The use of a GA drastically reduces the number of trajectories to analyze, speeding up the planning procedure. The achieved results were qualified by expert neurosurgeons as satisfactory. Our proposed method allows neurosurgeons to calibrate the surgical planning system by allowing them to establish the risk brain structure and the risk value for each structure.

About 90% of the Ataulfo mango (Mangifera indica L.) crops in Mexico are in the south of the country. This variety has significant amounts of antioxidant compounds. All the trees come from a small group of parents, however, the possible intravarietal variations and the micro-environments where it is grown can influence the compounds that contribute to the antioxidant capacity. The objective of this study was to quantify the antioxidant compounds of Ataulfo mango fruits of trees grown in Soconusco, Chiapas, Mexico (origin denomination), as well as fruits of the parent trees. In addition, possible associations between the contents of these compounds and the micro-environmental conditions collected were sought. In total, 465 fruits from 155 trees planted in 13 municipalities (locations) were analyzed. Fruits were collected at physiological maturity and stored at 25 °C until reaching commercial maturity. The contents of total phenolic compounds (TPC), antioxidant capacity (AC by DPPH, ABTS and FRAP methods), total anthocyanins (TA) and ascorbic acid (AA) were determined. The fruits from Huehuetán, presented the highest contents of PC (0.89 mg GAE g-1); however, the highest AC was found in the fruits harvested in Frontera Hidalgo, with 128.29 µmol TE g-1 (ABTS). The fruits obtained from the parents are within the average range of total TPC and AC, without significant differences between their fruits and those cultivated. The micro-environments where the Ataulfo mango trees are grown do not have a significant effect on antioxidant compounds (TPC, AC, TA and AA) and the only variables that allow segregation by localities are relative humidity, environmental temperature and altitude.

Two series of novel [1,2,4]triazolo[4,3-c]- and [1,2,4]triazolo[1,5-c]quinazoline fluorophores with 4’-amino[1,1′]-biphenyl residue at position 5 have been prepared via Pd-catalyzed cross-coupling Suzuki-Miyaura reactions. The treatment of 2-(4-bromophenyl)-4-hydrazinoquinazoline with orthoesters in solvent-free conditions or in absolute ethanol leads to the formation of [4,3-c]-annulated triazoloquinazolines, whereas [1,5-c] isomers are formed in acidic media as a result of Dimroth rearrangement. 1D-NMR and 2D-NMR spectroscopy as well as single‐crystal X‐ray diffraction analysis unambiguously confirmed the annelation type and determined the molecular structure of p-bromophenyl intermediates and target products. Photophysical properties of the target compounds were investigated in two solvents and solid state and compared with those of related 3-aryl-substituted [1,2,4]triazolo[4,3-c]quinazolines. The excluding of aryl fragment from triazole ring has been revealed to improve fluorescence quantum yield in solution. Most of the synthesized structures show moderate to high quantum yields in solution. Additionally, the effect of solvent polarity on the absorption and emission spectra of fluorophores has been studied and considerable fluorosolvatochromism was stated. Moreover, electrochemical investigation and DFT calculations have been performed, their results are consistent with the experimental observation.

Developmental hazard evaluation is an important part of assessing chemical risks during pregnancy. Toxicological outcomes from prenatal testing in pregnant animals result from complex chemical-biological interactions, and while New Approach Methods (NAMs) based on in vitro bioactivity profiles of human cells offer promising alternatives to animal testing, most of these assays lack cellular positional information, physical constraints, and regional organization of the intact embryo. Here, we engineered a fully computable model of the embryonic disc in the compucell3d.org modeling environment to simulate epithelial-mesenchymal transition of epiblast cells and self-organization of mesodermal domains (chordamesoderm, paraxial, lateral plate, posterior/extraembryonic). Cell fate in the model is determined by an autonomous homeobox (HOX) clock driven by morphogenetic signals (e.g., FGF, WNT, ATRA, CDX). Executing the model renders a quantitative cell-level computation of mesodermal subpopulations and consequences of perturbation based on known embryogeny. For example, synthetic perturbation of the control network rendered altered phenotypes (cybermorphs) mirroring experimental mouse embryology, with 50% reductions in FGF4, FGF8 and BMP4 signaling resulting in 86%, 98% and 59% reductions, respectively in the posterior mesodermal population, while ATRA exposure also resulted in a 78% decrease in this population. This model enables integration of in vitro chemical bioactivity data for specific molecular targets with known embryology to test mechanistic veracity and quantitative prediction of altered development.

Global demand for sleep-tracking wearables, or consumer sleep technologies (CSTs), is steadily increasing. CST marketing campaigns often feature a scientific component, but the scientific relevancy and monetary value of CST features within the sleep research community remains unquantified. Sleep medicine experts were recruited through social media and nonprobability sampling techniques to complete a survey identifying sleep metrics and device features that are most desirable to the scientific community. A hypothetical purchase task (HPT) estimated economic valuation for devices with different features by price. Forty-six (N=46) respondents with an average of 10±6 years’ experience conducting research in real-world settings completed the online survey. Total sleep time was ranked as the most important measure of sleep followed by objective sleep quality while sleep architecture/depth and diagnostic information were ranked as least important. Experts preferred wrist-worn devices that could reliably determine sleep episodes as short as 20 minutes. Economic value was greater for hypothetical devices with longer battery life. These data set a precedent to determine how scientific relevance of a product impacts the potential market value of a CST device. This is the first known attempt to establish consensus opinion or economic valuation for scientifically-desirable CST features and metrics using expert elicitation.

Framed in a context with an emerging economy and with a high percentage of school failure, this study aimed to identify the factors that turn students with socioeconomic disadvantages into resilient students. Two questions guided the research: Can resilience be supported in students in adverse socioeconomic situations? What factors influence building resilient students? A cross-sectional study was carried out from 2011 to 2015 in Chile, using a multilevel logistic regression model with three levels, considering the hierarchical data structure. The behavior of 63100 to 76400 sampled students was analyzed. Results show five relevant factors in building resilience: self-efficacy in language, minor aggressions and violence perceived by students, norms and values of the establishment, interest in study, and self-efficacy. Some risk factors identified were an atmosphere of less respect and trust, engagement in physical education activities and good performance in carrying them out. These results could orient educational leaders interested in supporting the educational community in order to improve the academic success of disadvantaged students.

This document presents the design and manufacture of a reflectarray (RA) antenna for the Ku-band, based on a fully-metallic 3D architecture. The reflectarray unit cell is formed by a square-shaped waveguide section ended in a short circuit, that is the reflectarray back ground plane. Each cell has the ability of configuring the phase of its own reflected field by means of resonators perforated on the walls of the cell waveguide section. The resonator-based waveguide cell introduces the 3D character to the design. The geometry of the resonators and its size variation introduces the phase behaviour of each cell, conforming the radiation pattern of the reflectarray. This design explores the potential of phase value truncation (6 states and 2 states), and demonstrates that proper pattern results can be obtained with this phase truncation.

Abstract: The probability of existence or not of local extinctions of six species of carnivorous mammals was analyzed by ordering the species composition in nested subsets in 7 fragments of forest habitats in the Coastal Mountains in the Araucanía Region, in southern Chile. Nested Temperature Calculator (NTC) and BINMATNEST computer programs were used to process the results. The first software provided a temperature in the archipelago of 28.21 degree Celsius, whereas the second program showed a nesting temperature of 16.58 degree Celsius. The computer software used in this study suggest that there is no nesting pattern at the level species composition of carnivorous mammal assemblage in the evaluated area, which may be due to the habitat use characteristics of the different carnivorous mammals studied here.

Plastic flow in body-centered cubic (bcc) alloys is governed by the thermally-activated screw dislocation motion. In bcc interstitial solid solutions, solute diffusion can occur at very fast rates owing to low migration energies and solute concentrations. Under mechanical loading, solutes may move on the same or similar time scale as dislocations glide, even at low temperatures, potentially resulting in very rich co-evolution processes that may have important effects in the overall material response. It is therefore important to accurately quantify the coupling between interstitial impurities and dislocations, so that larger-scale models can correctly account for their (co)evolution. In this paper, we use electronic structure calculations to obtain the energetics of oxygen diffusion under stress and its interaction energy with screw dislocation cores in bcc tungsten. We find that oxygen atoms preferentially migrate from tetrahedral to tetrahedral sites with an energy of 0.2 eV. This energy couples only weakly to hydrostatic and deviatoric deformations, with activation volumes of less than $0.02$ and $0.2b^3$, respectively. The strongest effect is found for the inelastic interaction between O atoms and screw dislocation cores, which leads to attractive energies on the order of 1.5 eV and a structural transformation of the screw dislocation core from an `easy' to a `hard' core configuration

This study introduces and demonstrates a comprehensive, accurate, unbiased approach to robust quantitative comparison of Electronic Nicotine Delivery Systems (ENDS) appropriate for establishing substantial equivalence (or lack thereof) between tobacco products. The approach is demonstrated across a family of thirteen pen- and pod-style ENDS products. Methods employed consist of formulating a robust emissions surface regression model, quantifying the empirical accuracy of the model as applied to each product, evaluating relationships between product design characteristics and maximum emissions characteristics, and presenting results in formats useful to researchers, regulators, and consumers. Results provide a response surface to characterize emissions (total particulate matter and constituents thereof) from each ENDS appropriate for use in a computer model and for conducting quantitative exposure comparisons between products. Results demonstrate that emissions vary as a function of puff duration, flow rate, E-Liquid composition, and device operating power. Further, results indicate that regulating design characteristics of ENDS devices and consumables may not achieve desired public health outcomes; it is more effective to regulate maximum permissible emissions directly. Three emissions outcome measures (yield per puff, mass concentration and constituent mass ratio) are recommended for adoption as standard quantities for reporting by manufacturers and research laboratories. The approach provides a means of (a) quantifying and comparing maximal emissions from ENDS products spanning their entire operating envelope, (b) comparative evaluation of ENDS devices and consumable design characteristics, and (c) establishing comparative equivalence of maximal emissions from ENDS. A consumer-oriented product emissions dashboard is proposed for comparative evaluation of ENDS exposure potential. Maximum achievable power dissipated in the coil of ENDS is identified as a potentially effective regulatory parameter.

Misuse of measurement units and orientations leads to errors in scientific applications, Cyber Physical Systems (CPS), and IoT C/C++ programs. Standard type system are inadequate in preventing such errors. Although dimensional and orientational analysis in physics can manually detect these errors in equations, analyzing complex code with intricate physical computations is impractical. To overcome this challenge, we propose an advanced type system that incorporates units and orientations as integral components within a specialized type library. Our enhanced type system automatically detects potential errors during compile time by representing physical quantities as types and utilizing dimensional analysis, orientational analysis, and metaprogramming techniques. Our improved type system enables formal verification of C++ software, successfully verifying programs with extensive codebases. We also employ it for runtime verification of dynamic linking and pointer operations in C++ programs. The integration of compile-time verification, dimensional analysis, orientational analysis, and advanced type system enhances the robustness and accuracy of scientific applications, CPS, and IoT C/C++ programs. By leveraging these approaches, we ensure precise calculations and prevent errors related to measurement units and orientations, resulting in substantial improvements in reliability and accuracy.

Suzuki cross-coupling reaction has developed one of the furthermost effectual approaches for the synthesis of biaryls or substituted aromatic moieties from aryl halides and arylboronic acids with a palladium-catalyst in the past two era’s. Herein, Pd-free layered double hydroxide containing nickel catalysts were prepared by co-precipitation method under ultrasonic irradiation and N2 atmosphere with different molar ratios of Ni: Mg: Al and coded as (1NiLDHs-Dr), (1.5NiLDHs-Dr) and (2NiLDHs-Dr). A series of reduced catalysts under 5%H2/N2 at different temperatures were coded as 1NiLDHs-R200, 1.5NiLDHs-R200 and 2NiLDHs-R200. As-synthesized 2NiLDHs-Dr was the superlative catalyst when coupling different aryl halides with different boronic acids derivatives. Deep investigation of all catalysts was done using different techniques such as inductively coupled plasma optical emission spectroscopy (ICP-OES), x-ray photoelectron spectroscopy (XPS), powder x-ray diffraction (XRD), thermogravimetric analyses (TGA), Fourier transfer infrared (FTIR), scanning electron microscope (SEM) connected with energy dispersive x-ray (EDX) and N2-physisorption at -196 ℃. The results attained verified that ɑ-Ni(OH)2 was fashioned for 2NiLDHs-Dr catalyst and the enclosure of nickel ions in the cationic sheet of layered structure were responsible for the fascinating catalytic efficacy rather than the basic nature of material. The Ni-containing LDHs catalysts encourage forthcoming studies in Pd-free catalyzed C-C coupling reactions.

Introduction: Carcinoid heart disease is a rare cause of right-sided valvular dysfunction, an important complication in patients with carcinoid syndrome. Objectives: We aim to present our own experience regarding early myocardial dysfunction in patients with carcinoid syndrome. Methods: 64 patients (35-90 year old, 62,5% female, 37,5% male patients) with carcinoid syndrome were evaluated be-tween October 2017 and June 2021. All patients underwent two-dimensional echocardiography with additional tissue Doppler and speckle-tracking techniques. For all patients there were measured urinary level of 5- hydroxyindolacetic acid, serotonin and NT-proBNP values. Results: The following echocardiographic features: global longitudinal strain of both ventricles, mean systolic velocity of the left ventricle, systolic velocity of the free wall of right ventricle, correlated with high values of specific biomarkers: serotonin, and urinary 5-hydroxyindolacetic acid, and also with the presence of hepatic metastases and poorly differentiated tumors. Discussion: In this study we identified several patients with early myocardial dysfunction due to carcinoid syndrome, representing a predictive model of poor prognosis, requiring further investigations. Conclusion: Echocardiographic assessment based on the measurement of systolic velocities, as well as the global longitudinal strain of both ventricles, together with specific biomarkers may contribute to better recognition of carcinoid heart disease in clinical practice, but this needs validation through further studies enrolling larger number of patients.

Protein tyrosine phosphatase receptor type E (PTPRE) is a member of the “classical” protein tyrosine phosphatase subfamily and regulates a variety of cellular processes in a tissue-specific manner by antagonizing the function of protein tyrosine kinases. PTPRE plays a tumorigenic role in different human cancer cells, but its role in retinoblastoma (RB), the most common malignant eye cancer in children, remains to be elucidated. Etoposide resistant RB cell lines and RB patients display significant higher PTPRE expression levels compared to chemosensitive counterparts and the healthy human retina, respectively. PTPRE promotor methylation analyses revealed that PTPRE expression in RB is not regulated via this mechanism. Lentiviral PTPRE knockdown (KD) induced a significant decrease in growth kinetics, cell viability, and anchorage independent growth of etoposide resistant Y79 and WERI RB cells. Caspase-dependent apoptosis rates were significantly increased and a re-sensitization for etoposide could be observed after PTPRE depletion. In vivo chicken chorioallantoic membrane (CAM) assays revealed decreased tumor formation capacity as well as reduced tumor size and weight following PTPRE KD. Expression levels of miR631 were significantly downregulated in etoposide resistant RB cells and patients. Transient miR631 overexpression resulted in significantly decreased PTPRE levels and concomitantly decreased proliferation and increased apoptosis levels in etoposide resistant RB cells, impacts mirroring PTPRE KD effects and indicating PTPRE regulation via this miR. Additionally, PTPRE KD led to altered phosphorylation of protein kinase SGK3 and - dependent on the cell line - also AKT and ERK1/2, suggesting potential PTPRE downstream signaling pathways. In summary, these results indicate an oncogenic role of PTPRE in chemoresistant retinoblastoma.

We aimed to assess the caffeine intake before and during pregnancy, compliance with caffeine recommendations during pregnancy (200 mg/day) and factors associated with higher intakes before and in first trimester of pregnancy. Caffeine consumption was collected in a Spanish cohort of pregnant women through a validated food questionnaire, before and in each trimester of gestation (T1, T2 and T3). 463 pregnant women were recruited and follow-up through pregnancy. Compliance with caffeine intake recommendations during pregnancy and quintiles of mg/day of caffeine before and in T1 of pregnancy were calculated. A multivariate logistic regression, comparing extreme quintiles of consumption (Q1 vs Q5) was used. Mean caffeine intake before pregnancy was 120.05 mg/day (SD 117.85), 42.76 mg/day (SD 63.90) at 12th GW, 42.00 mg/day (SD 59.76) at 24th GW and 39.34 mg/day (SD 50.9) at 32nd GW (p&lt;0.001). 86% of women complied with caffeine recommendations during pregnancy. At pregnancy (T1), being an active smoker was associated with Q5 &gt; 100.1 mg/day, aOR = 22.69; 95% CI 4.67- 110.26. igh diet quality, aOR = 0.30; 95% CI, 0.13- 0.68, and moderate physical activity level, aOR= 0.44; 95% CI, 0.19-1.00, were inversely associated with Q5 &gt; 100.1 mg/day. Pregnant women are mostly adhering to current caffeine intake guidelines. Higher caffeine intake at pregnancy is associated with other unhealthy habits during pregnancy.

Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost variances using proprietary C-S and S-C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

Andalusia is a Spanish region that is home to numerous minority varieties due to its diversity and territorial extension, offering the local viticulture the possibility of diversifying its wine production. The molecular identification of 98 specimens from six areas with a winemaking tradition in Andalusia was carried out between the years 2020 and 2022. Thirteen microsatellite markers were used in this study, including the nine recommended by the OIV. 31 different genotypes were obtained, 20 of which corresponded to profiles of already described varieties (11 of them are of minority cultivation in Andalusia: 'Rojal Tinto', 'Beba', 'Zurieles', 'Rome', 'Hebén', 'Mollar Cano', 'Listán Prieto', 'Listán del Condado', 'Jarrosuelto', 'Negra Dorada' and 'Mantúo de Pilas'), while the other 11 profiles did not match with previously identified varieties. This profiles were integrated into the database of the IFAPA “Rancho de la Merced” Germplasm Bank. The eco-geographical groups of the new identified genotypes were determined through analysis of genetic diversity. The presence of the Grapevine Fanleaf Virus, the Grapevine Fleck Virus and the Grapevine Leafroll associated Viruses was also analyzed using an ELISA test due to the necessity of having certifiable clones of the new varieties for their potential interest in being authorized for its cultivation in Spain.

The effects of post-treatment temperature-based methods on 1D single PLA filaments after FFF have been studied. This lets to decouple the variables related to the 3D structure (layer height, raster angle, infill density, and others) from the variables solely related to the material (molecular weight, molecular orientation, crystallinity, and others). PLA 1D filaments have been aged at 20, 39, 42, 51, 65, 75 and 80 ºC in a water-bath-inspired process in which the hydrolytic degradation of the PLA has been minimised for the ageing temperatures of interest. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded. Differential scanning calorimetry (DSC) was used to evaluate thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation and melting reactions were analysed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting and the so-called summer effect –stabilisation of properties at higher temperatures– are discussed for assessing the safeness of accelerating ageing.

This paper aims to provide the smart grid research community with an open and accessible general mathematical framework to develop and implement optimal flexibility mechanisms in large-scale network applications. The motivation of this paper is twofold. On the one hand, flexibility mechanisms are currently a hot topic of research, which is aimed to mitigate variation and uncertainty of electricity demand and supply in decentralised grids with a high aggregated share of renewables. On the other hand, a large part of such related research is performed by heuristic methods, which are generally inefficient (such methods do not guarantee optimality) and difficult to extrapolate for different use cases. Alternatively, this paper presents an MPC-based (Model Predictive Control) framework explicitly including a generic flexibility mechanism which is easy to particularise to specific strategies such as Demand Response, Flexible Production and Energy Efficiency Services. The proposed framework is benchmarked with other non-optimal control configurations to better show the advantages it provides. The work of this paper is completed by the implementation of a generic use case which aims to further clarify the use of the framework and thus, to ease its adoption by other researchers in their specific flexibility mechanisms applications.

This paper investigates the use of deep learning techniques to perform energy demand forecasting. Specifically, the authors have adapted a deep neural network originally thought for image classification and composed of a convolutional neural network (CNN) followed by a multilayered fully connected artificial neural network (ANN). The convolutional part of the network was fed with a grid of temperature forecasting data distributed in the area of interest in order to extract a featured temperature. The subsequent ANN is then fed with this calculated temperature along with other data related to the timing of the forecast. The proposed structure was first trained and then used in a real setting aimed to provide the French energy demand forecast using ARPEGE forecasting weather data. The results show that the performance of this approach is in the line of the performance provided by the reference RTE subscription-based service, which opens the possibility to obtain high accuracy forecasting using widely accessible deep learning techniques through open-source machine learning platforms.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Abstract: Hyperuricemia is commonly diagnosed in subjects with abnormal purine metabolism. Prolonged hyperuricemia often associated with gout, which is a vital risk factor for joint dysfunction. The current study was designed to determine the efficacy of vitamin C supplements for treatment of high serum uric acid (UA) among hyperuricemic and gouty patients, and finding-out the effect of supplementation on serum creatinine (Cr) level and glomerular filtration rate (GFR). This intervention study was started in April, 2013, till two months. A convenient sample of 30 adults aged between 24-75 years of both genders was assigned into two study groups: hyperuricemic (n=15) and gouty (n=15) groups. Each participant supplemented with 500 mg/day vitamin C chewable tablets for 2 months. Serum UA, Cr, and GFR were measured before and after treatment. At the end of this study, Cr and GFR enhanced insignificantly in both groups. UA increased insignificantly in gouty group after 2 months by about 0.31 mg/dl. On the other hand, hyperuricemic group showed significant (P ≤0.05) decrease in UA (-0.78 mg/dl) after 2 months duration. In conclusion, supplementation with 500 mg/day vitamin C for 2 months significantly attenuated serum UA for hyperuricemic patients and insignificantly affected serum UA in gouty patients. The uselessness of vitamin C supplements on gouty patients could be associated to a number of possible reasons.

Nonparametric assessments of police technical and scale efficiency is challenging because of the stochastic nature of criminal behavior and because of the subjective dependence on multiple decision criteria, which can lead to a more or less efficiency prospect depending on the regulation, necessity, or organizational objective. There is a trade-off between efficiency and effectiveness in many police performance assessments, i.e., efficient departments (producing more clear-ups with a given resource) are crime-specialized or cannot reproduce those good results effectively on more severe or complex occurrences. This study proposes a combined methodology for carrying out efficiency and effectiveness analysis of Police departments. A conditional non-parametric approach, which allows to include crime as an external factor in the analysis, is combined with a non-compensatory ranking based on the PROMETHEE II methodology for the approach illustrated on the multidimensional efficiency and effectiveness comparison of 145 Pernambuco (Brazil)'s police departments. The application results offer compelling perspectives for public administrations concerning the strategic prioritization of units for rewards or interventions.