In neonatal equines, pathologies involving umbilical structures are an important cause of morbidity, and surgical removal of urachal remnants is a common procedure in clinical practice. Surgery involving the ventral abdominal wall can cause substantial pain, leading to complications and prolonged recovery. The objectives of this study were to describe a two-point bilateral ultrasound-guided rectus sheath block at the level of the umbilicus and to evaluate the extent of dye distribution in foal cadavers. Ten foal cadavers were included in the study, in which a bilateral two-point ultrasound-guided rectus sheath block was performed—one injection cranially and a second one caudally to the umbilicus. The injectate consisted of a mixture of iodinated contrast medium and blue dye at a volume of 0.25 mL kg-1 per injection point (total 1 mL kg-1). After the injection, computer tomography and subsequent dissection of the ventral abdominal wall were performed. The extension of the contrast medium, the number of stained nerves, and contamination of the abdominal cavity were evaluated. The cranio-caudal extension of the contrast ranged from 0.8 to 1.4 centimeters per milliliter of injectate. The most commonly stained ventral branches of spinal nerves were thoracic (Th) nerves 16, 17, and 18 (95%, 85%, and 80% of the nerves, respectively). Abdominal contamination was found in 4 animals. The results suggest that the block could provide periumbilical analgesia. Further studies with different volumes of injectate and living animals are warranted.

This work deals with the evaluation of adhesive single-lap joints using ultrasonic guided waves. An adhesive bonded lap joint can be modelled as a three-layer system made up of two adherents and an adhesive. The propagation of guided waves in the joint is developed from matrix formulations. The behavior of the different guided wave modes that propagate in the bonded region is characterized and it is found that their relative amplitudes can be estimated based on the properties of the incoming wave that propagates in the non-bonded region. It was verified that the excitation of these modes is ruled by the degree in which the shapes of both modes match each other. A 3D simulation of two aluminium bonded plates using 500 kHz ultrasonic transducers in a pitch and catch configuration was implemented using the Matlab k-Wave toolbox. Scattering effects due to some produced defects located in the bond line of the lap joints were simulated. Experimental setup with some artificial defects produced in the aluminum joints were used in order to compare with the simulated. Qualitative agreement was observed for the two approaches. The observed deviation can be due to the different characteristics of the experimental and simulated defects.

Academic publishing is undergoing a highly transformative process, and many rules and value systems that were in place for years are being challenged in unprecedented forms leading to the evolution of novel ways of dealing with new pressures. One of the most important aspects of an integrated and valid academic literature is the ability to screen publications for errors during peer review to weed out mistakes, fraud and inconsistencies, such that the final published product represents a product that has value, intellectually, and otherwise. It is difficult to claim the existence of perfect manuscripts. The level of errors that exist in a manuscript will depend on the rigor of the research group and of the peer review process that was used to screen that paper. When errors slip into a final published paper, either through honest error or misconduct, and are not detected during peer review and editorial screening, but are spotted during post-publication peer review, an opportunity is created to set the record straight, and to correct it. To date, the most common forms of correcting the literature have been errata, corrigenda, expressions of concern, and retractions. Despite this range of corrective measures, which represent artificially created corrals around pockets of imperfect literature, certain cases do not quite fit this mold, and new suggested measures for correcting the literature have been proposed, including manuscript versioning, amendments, partial retractions and retract and replace. In this commentary, a discussion of the evolving correction of the literature is provided, as are perspectives of the risks and benefits of such new measures to improve it.

: For a long time, atherosclerosis has been regarded as a mere lipid deposit in the blood vessels. However, in the recent years a growing body of experimental and clinical evidence have highlighted the role of inflammation and immunity as a central mechanism of disease. Moreover, in the last decade the coming of next-generation sequencing and its application to large human population has broken the barrier between inflammation and cancer. Indeed, acquired mutation in key genes related to the control of hematopoiesis and myeloproliferation have paved the way to establish the new concept of clonal hematopoiesis of indeterminate potential. This phenomenon is being considered not such “indeterminate”, but as an emerging cardiovascular risk factor. Thus, this may explain the mechanisms of myeloproliferation and inflammation in atherosclerosis. And in a bidirectional journey, it has helped to explain the extremely high cardiovascular risk in cancer survivors, in particular in myeloprolfierative neoplasm patients. A deeper understanding of these mechanisms may pave the way for the future early diagnosis and potential preemptive treatments of the leading worldwide cause of death.

Artificial Intelligence (AI) has emerged as a disruptive technology in various areas, and medicine is no exception. In the last decade, there has been rapid progress in the application of AI in healthcare, from diagnosing and prognosticating diseases to improving operational efficiency in hospitals. This literature review explores the advances of artificial intelligence in the field of medicine, discusses its benefits, and discusses the ethical and regulatory challenges that need to be addressed to maximize its potential.

The COVID-19 pandemic crisis has brought about unprecedented economic and social consequences worldwide. The implementation of isolation measures, including national and international travel restrictions, significantly affected contact-intensive sectors such as tourism. During this lockdown period, Information and Communication Technology (ICT) was crucial in maintaining connectivity and enabling remote activities. Governments across the world implemented discretionary measures to mitigate the crisis's adverse effects on economic activity. This paper aims to analyze whether the level of ICT adoption and the importance of tourism influence the fiscal policy efforts pursued by governments. Based on the results of a linear regression analysis for 154 countries, the findings suggest that in countries with higher international tourism receipts, the governments had to promote higher fiscal stimulus. At the same time, ICT development diminished the efforts of the fiscal policy response to the crisis since it facilitated economic resilience. The findings of this study can contribute to understanding how governments responded to the pandemic crisis and the factors that influenced their fiscal policy decisions.

As synthetic/artificial life forms become more abundant and sophisticated, an increasing number of bizarre creatures - xenobots, robots, soft A-life entities, genetically engineered organisms, etc. - are invading our society. Therefore, we need to bring order to all this, to establish what is living and what is not. Here, I intend to classify all these non-natural entities and clarify their status with reference to their consideration or not as living beings, leaving the door open to an uncertain future in which perhaps we can see how "the artificial" and "the natural" merge to originate something new. To order all this "new biodiversity" and to also give entry to viruses (which are excluded of the three-domains tree of life), I propose the creation of a new domain, Lithbea (from the name: life-in-the-border entities), in which all these new human-made entities as well as the viruses will be included. Within this domain there would be two kingdoms, Virus and Humade (contraction of human-made), based on their origin, natural or human-made. A brief description of each component of Lithbea is included and the implications for society and biology of this “new biodiversity” is briefly discussed.

The ecosystem is an essential biological concept linking the living and the inanimate and represents the main structural and functional unit of nature. The biodiversity that exists on our planet can be organized into closely interconnected living worlds: acellular (viruses and capsidless genetic elements), prokaryotic (bacteria and archaea), and eukaryotic (all nucleated organisms). I want to highlight the presence of viruses as components of biodiversity because they are often overlooked in many studies despite their essential ecological and evolutionary role. Furthermore, I propose seven distinctive hallmarks that are inherent to any ecosystem: biodiversity, physical environment, hierarchy, interactivity, openness, “homecostasis”, and evolutionary. From the interaction and coupling of these living worlds with the environment (the environmental world), I define the ecosystem as a specific and dynamic ensemble of living and non-living worlds that functions as an open, hierarchical, and evolving system. This complex web of interactions that we call ecosystem can be graphically represented as a triangle reflecting the dynamic equilibrium between all the worlds. Finally, I propose a new way of graphically relating the ecosystem to biodiversity by taking the ecosystem as the nucleus from which all living worlds emerge.

What is life, what is the difference between something that is alive and something that is not, are viruses living beings, or what would life be like elsewhere in the universe, are questions that still do not have clear-cut answers fully accepted by the scientific community. Based on the fundamental attributes of all living things, I define life as a process that takes place in very ordered organic structures and is characterized by being automatic, interactive and evolutionary. I also define a living being as an organic, highly ordered, automatic, interacting and evolutionary system, and a robot as an ordered automatic and interacting system. Based on this definition and what we know about the biology of viruses, I maintain that they should be considered as living entities. Finally, I explain why if there were life elsewhere in the universe, it would be very similar to what we know on our planet.

We know that living matter must behave in accordance with the universal laws of physics and chemistry. However, these laws are insufficient to explain the specific characteristics of the vital phenomenon and, therefore, we need new principles, intrinsic to biology, which are the basis for developing a theoretical framework for understanding life. Here I propose what I call the seven commandments of life (the Vital Order, the Principle of Inexorability, the Central Dogma, the Tyranny of Time, the Evolutionary Imperative, the Conservative Rule, the Cooperating Thrust) as a set of principles that help us explain the vital phenomenon from an evolutionary perspective. In a metaphorical way, we can consider life like an endless race in which living beings are the runners, who are changing as the race goes on (the evolutionary process), and the commandments the rules.

In this study, we examine microscale waterflooding in a randomly close-packed porous medium. Three different porosities are prepared in a microfluidic platform and saturated with silicone oil. Optical video fluorescence microscopy is used to track the water front as it flows through the porous packed bed. The degree of water saturation is compared to water containing two different types of chemical modifiers, sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP), with water in the absence of a surfactant used as a control. Image analysis of our video data yield saturation curves and calculate fractal dimension, which we use to identify how morphology changes the way an invading water phase moves through the porous media. An inverse analysis based on the implicit pressure explicit saturation (IMPES) simulation technique uses mobility ratio as an adjustable parameter to fit our experimental saturation curves. The results from our inverse analysis combined with our image analysis show that this platform can be used to evaluate the effectiveness of surfactants or polymers as additives for enhancing the transport of water through an oil-saturated porous medium.

Recent developments, begun by the ascending spiral of the anticipated endless prospects of ChatGPT, promote artificial intelligence (AI) as an indispensable tool and commodity whose time has come. Yet the sinister specter of a technology that has hidden and unmanageable attributes that might be harmful to society looms in the background. As well as the likelihood that it will never deliver on the purported promise of artificial general intelligence (AGI). Currently the prospects for the development of AI and AGI are more a matter of opinion than based on a consistent methodological approach. Thus the need to take a step back to develop a general framework from which to evaluate current AI efforts, which also permits the determination of the limits to its future prospects as AGI. To gain insight into the development of a general framework, a key question that needs resolution is, what is the connection between human intelligence and machine intelligence? This is the question that needs a response because humans are at the center of AI creation and realize that without an understanding of how we become what we become, we have no chance of finding a solution. This work proposes infoautopoiesis, the self-referential, recursive and interactive process of self-production of information, as the needed general framework. Infoautopoiesis shows how the key ingredient of information is fundamental to an insightful resolution to this crucial question and allows predictions as to the present and future of AGI.

Let $\mathcal{N}$ be an arbitrary class of matroids, closed under isomorphism. For $k$ a positive integer, we say that $M \in \mathcal{N}$ is \emph{$k$-minor-irreducible} if $M$ has no minor $N \in \mathcal{N}$ such that $1\leq\left|E\left(M\right)\right|-\left|E\left(N\right)\right|\leq k $. Tutte's Wheels and Whirls Theorem establish that, up to isomorphism, there are only two families of 1-minor-irreducible matroids in the class of 3-connected matroids. More recently, Lemos classified the 3-minor-irreducibles with at least 14 elements in the class of triangle-free 3-connected matroids. Here we prove a local characterization for the 2-minor-irreducible matroids with at least 11 elements in the class of triangle-free 3-connected matroids. This local characterization is used to establish two new families of 2-minor-irreducible matroids in this class.

High concentrations of Na⁺ or [Co(NH₃)₆]³⁺ can induce the B to Z conformational transition in alternating (dC-dG) oligo and polynucleotides. The use of short DNA oligomers (dC-dG)₄ and (dm⁵C-dG)₄ as models can allow a thermodynamic characterization of the transition. Both form right handed double helical structures (B-DNA) in standard phosphate buffer with 115 mM Na⁺ at 25 ^oC. However, at 2.0 M Na⁺ or 200 mM [Co(NH₃)₆]³⁺, (dm⁵C-dG)₄ assumes a left handed double helical structure (Z-DNA) while the unmethylated (dC-dG)₄ analogue remains right handed under those conditions. We have previously demonstrated that the enthalpy of the transition at 25 ^oC for either inducer can be determined using isothermal titration calorimetry (ITC) [Ferreira, J. M. & Sheardy, R. D., Biophys. J. 2006, 91, 1–7]. Here, ITC is used to investigate the linkages between temperature, water activity and DNA conformation. We found that the determined enthalpy for each titration varied linearly with temperature allowing determination of the heat capacity change (DC_p) between the initial and final states. As expected, the DC_p values were dependent upon the cation (i.e. Na⁺ vs [Co(NH₃)₆]³⁺) as well as the sequence of the DNA oligomer (i. e., methylated vs unmethylated). Osmotic stress experiments were carried out to determine the gain or loss of water by the oligomer induced by the titration. The results are discussed in terms of solvent accessible surface areas, electrostatic interactions and the role of water.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

In the context of Shared Autonomous Vehicles, the need to monitor the environment inside the car will be crucial. This article focuses on the application of deep learning algorithms to detect objects, namely lost/forgotten items to inform the passengers, and aggressive items to monitoring if violent actions may arise between passengers. For object detection algorithms was used public datasets (COCO and TAO) to train state-of-the-art algorithms, such as YOLOv5. For violent action detection was used the MoLa InCar dataset to train on state-of-the-art algorithms such as I3D, R(2+1)D, SlowFast, TSN and TSM. At the end an embedded automotive solution was used to demonstrate both methods running in real-time.

Live video streaming has become one of the main multimedia trends in networks in recent years. Providing Quality of Service (QoS) during live transmissions becomes a challenge due to the stringent requirements for low latency and minimal interruptions. This scenario has led to a high dependence on cloud services, implying a widespread usage of Internet connections, which constrains contexts where an Internet connection is not available. Thus, alternatives such as Mobile Ad Hoc Networks (MANETs) emerge as potential communication techniques. These networks operate autonomously with mobile devices serving as nodes, without the need for coordinating centralized components. However, these characteristics lead to challenges to live-video streaming, such as dynamic node topologies or periods of disconnection. Considering these constraints, this paper investigates the application of Artificial Intelligence (AI)-based classification techniques to provide adaptive streaming in MANETs. For this, a software-driven architecture is proposed to route stream in offline MANETs, predicting the stability of individual links and compressing video frames accordingly. The proposal has been implemented and assessed in a laboratory context, analyzing the model performance and QoS metrics. As a result, the model is implemented in a decision forest algorithm, which provides 95.9% of accuracy. Also, obtained latency values become assumable for video streaming, manifesting a reliable response for routing and node movements.

Rangelands are a key resource present all over the world as it covers half of emerged lands. They are even more important in drylands, where they cover 48% of the total area. Intensification and the additional pressure added by climate change push these systems towards desertification. Over the last two decades, we have developed and applied System Dynamics (SD) models for the study of Mediterranean grasslands. In addition, we have developed procedures and analysis tools, such as global sensitivity analysis, stability analysis condition, or risk analysis, in order to detect the main drivers of these socio-ecological systems and provide indicators about their long-term sustainability. This paper reviews these works, their scientific background, and the most relevant conclusions, including purely technical and rangeland-related ones as well as our experience as systemic modelers in a world driven by field specialists.

In this paper a more flexible extension of the Fréchet distribution is introduced. The new distribution is defined by means of the stochastic representation as the quotient of two independent random variables, a Fréchet distribution and the power of a random variable with uniform distribution in the interval (0,1). We will call this new extension the Slash Fréchet distribution and one of its main characteristics is that its tails are heavier than the Fréchet distribution. The general density of this distribution and some basic properties are determined. Its moments, skewness coefficients and kurtosis are calculated. In addition, the estimation of the model parameters is obtained by the method of moments and maximum likelihood. Finally, two applications with real data are performed by fitting the new model and comparing it with the Fréchet distribution.

Polyolefin fibre reinforced concrete (PFRC) has become an attractive alternative to steel for the reinforcement of concrete elements mainly due to its chemical stability and the residual strengths that can be reached with lower weights. The use of polyolefin fibres can meet the requirements in the standards, although the main constitutive relations are based on the experience with steel fibres. Therefore, the structural contributions of the fibres should be assessed by inverse analysis. In this study, the fibre dosage has been fixed at 6kg/m³ and both self-compacting concrete and conventional concrete have been used to compare the influence of the positioning of the fibres. An idealized homogeneous distribution of the fibres with such fibres crossing from side to side of the specimen has been added to self-compacting concrete. The experimental results of three-point bending tests on notched specimens have been reproduced by using the cohesive crack approach. Hence, the constitutive relations were found. The significance of this research relies on the verification of the formulations found to build the constitutive relations. Moreover, with these results it is possible to establish the higher threshold of the performance of PFRC and the difficulties of limiting the first unloading branch typical of fracture tests of PFRC.

The positional cloning of single nucleotide polymorphisms (SNPs) of the neutrophil cytosolic factor 1 (Ncf1) gene, advocating that a low oxidative burst drives autoimmune disease, demands an understanding of the underlying molecular causes. A cellular target could be T cells, which have been shown to be regulated by reactive oxygen species (ROS). However, the pathways by which ROS mediate T cell signaling remain unclear. The adaptor molecule linker for activation of T cells (LAT) is essential for coupling T cell receptor-mediated antigen recognition to downstream responses, and it contains several cysteine residues that have previously been suggested to be involved in redox regulation. To address the possibility that ROS regulate T cell-dependent inflammation through LAT, we established a mouse strain with cysteine-to-serine mutations at positions 120 and 172 (LATSS). We found that redox regulation of LAT through C120 and C172 mediate its localization and phosphorylation. LATSS mice had reduced numbers of double-positive thymocytes and naïve peripheral T cells. Importantly, redox insensitivity of LAT enhanced T cell-dependent autoimmune inflammation in collagen-induced arthritis (CIA), a mouse model of rheumatoid arthritis (RA). This effect was reversed on an NCF1-mutated (NCF1m1j), ROS-deficient, background. Overall, our data shows that LAT is redox-regulated, acts to repress T cell activation, and is targeted by ROS induced by NCF1 in antigen-presenting cells (APCs).

Landscape changes based on spectral responses allow showing plant cover changes through diversity, composition, and ecological connectivity. The spatial and temporal vegetation dynamics of the Bijagual Massif from 1986 to 2021 were analyzed as a measure of ecological integrity, conservation, and territory. The covers identified were high open forest (Hof), dense grassland of non-wooded mainland (Dgnm), a mosaic of pastures and crops (Mpc), lagoons (Lag), and bare and degraded lands (Bdl). The Bijagual Massif has 8,574.1 ha. In 1986, Dgnm occupied 42.6% of the total area, followed by Mpc (32.8%) and Hof (24.5%); by 2000, Mpc and Hof increased (43.7 and 28.1%, respectively), while Dgnm decreased (28%); by 2021, Dgnm was restricted to the northeastern zone and continued to decrease (25.2%), Mpc occupied 52.9%, Hof 21.7% and Bdl 0.1%. Of the three fractions of the connectivity probability index, only dPCintra and dPCflux contribute to ecological connectivity. Hof and Dgnm show patches with biota habitat quality and availability. Between 1986 and 2021, Dgnm lost 1,489 ha (41%) and Hof 239.5 ha (11%). Mpc replaced various covers (1,722.2 ha; 38%) in 2021. Bijagual has a valuable biodiversity potential limited by Mpc. Territorial planning and sustainable agroecological and ecotourism proposals are required due to the context of the ecosystems.

Background: Permanent Daylight Savings Time (DST) may improve road safety by providing more daylight in the evening but could merely shift risk to morning commutes or increase risk due to fatigue and circadian misalignment. Methods: To identify how potential daylight exposure and fatigue risk could differ between permanent DST versus permanent Standard Time (ST) or current time arrangements (CTA), generic work and school schedules in five United States cities were modeled in SAFTE-FAST biomathematical modeling software. Commute data were categorized by morning (0700-0900) and evening (1600-1800) rush hours. Results: Percent darkness was greater under DST compared to ST for the total waking day (t=2.59, p=0.03) and sleep periods (t=2.46, p=0.045). Waketimes occurred before sunrise 63%±41% percent of the time under DST compared to CTA (42%±37%) or ST (33%±38%; F(2, 74)=76.37; p<0.001). Percent darkness was greater during morning (16%±31%) and lower during evening rush hour (0%±0%) in DST compare to either CTA (morning:7%±23%; evening:7%±14%) or ST (morning:7%±23%; evening:7%±15%). Discussion: Morning rush hour overlapped with students’ commutes and shift worker reverse commutes, which may increase traffic congestion and risk compared to evening rush hour. Switching to permanent DST may be more disruptive than either switching to ST or keeping CTA without noticeable benefit to fatigue or potential daylight exposure.

In recent years the yield of fruits and vegetables have been decreasing in Colombia, threatening national food security. Analysis of crop production data may lead to identifying cropping systems that have shown better adaptability to changes in climatic and non-climatic factors associated with agricultural production. The open database AGRONET keeps data of the agricultural activities conducted in Colombia, allowing to find the information organized by crops, regions and years; each row of the database registers farm information in Colombia. Aiming to identify resilient crops systems, agricultural data of fruits and vegetables were analyzed. First, trends in crop production were studied by year and locations, detecting the regions and crops with highest yields in the period from 2006 until 2020. Then, mixed linear regression and principal components analysis were applied to elucidate the relation between non-climatic factors and crop yield. In Colombia, vegetable production was more efficient than fruits, observing yields of 10.23 and 13.33 t ha^-1, respectively. On the other hand, the Colombian central region showed high yields for vegetables, while for fruits this was exhibited in northern and eastern locations. In the present study, yield variation responded to changes in the location of crop systems, while years had no effect on vegetable production. Furthermore, the price of the agricultural product and the cost of fertilizers were associated with the yield of the analyzed crops systems. In Colombia, carrot, cabbage, tomato papaya and pineapple are resilient crops whose yield increases especially by the regions where they are cultivated.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

Research on early stages of corrosion of steel bars, together with the formation and development of cracks induced in the surrounding concrete and caused by chloride penetration, is relevant in improving the durability of reinforced concrete structures. This paper uses integration of the analytical models examined in the published literature, combined with experimental research in corrosion induced at the concrete/steel interface, in estimating the time-to-crack initiation of reinforced concrete subjected to corrosion. This work studies the influence of the porous network and electric current density on the cracking process at early ages. The experimental campaign was performed by using an accelerated corrosion test on a conventional concrete (CC) and a concrete with silica fume (SFC) by submitting them to a current density of 50μA/cm² and 100μA/cm². Examination performed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) provided both qualitative and quantitative information on the penetration of the rust layer in the surrounding concrete porous network. Strain gauges were used to measure corrosion-induced deformations between steel and concrete matrices, as well as the formation of corrosion-induced cracks. A good correlation between the rate of penetration of the rust products in the surrounding pores and the delay of the cracking pressure in concrete was observed from the experimental results. This phenomenon is incorporated into the analytical model by using a reduction factor, which mainly depends on the pore size of the concrete. The crack width obtained exhibited a significant dependency on electric current density at the beginning of the test, depending mainly on the pore size of the concrete later.

Bone cement, mainly based in PMMA, is commonly used in different arthroplasty surgical proce-dures, and its use is essential for prosthesis fixation. However, its manufacturing process reaches high temperatures that can produce necrosis in the patients' surrounding tissues. In order to con-tribute to avoid this problem, the addition of graphene could delay the polymerisation of the MMA and, simultaneously, contribute to the optimisation of the composite material's properties. This article analysed the effect of the addition of different percentages of Highly Reduced Graphene Oxide (HRGO) with different wt. % (0,10, 0,50 and 1,00) and surface densities (150, 300, 500 and 750 m2/g) on the physical, mechanical, and thermal properties of commercial PMMA-based bone cement and its processing. It was noticed that a lower sintering temperature would be reached with this addition, making it less harmful to use in surgery and as it reduces its adverse effects. In contrast, the materials' density does not show significant changes, which indicates that the addi-tion of HRGO does not significantly increase its porosity. Lastly, the mechanical properties are re-duced by almost 20 %. Nevertheless, these properties are high enough so that these new materials can still fulfil their structural function.

The escalating environmental challenges that stem from urban residential waste in densely populated areas have become increasingly prominent in recent times. As a result, the waste management sector has experienced significant growth nationwide. However, due to the predominantly manual nature of these processes, their effectiveness falls short of meeting the current demand. Addressing these issues requires process enhancement. In this context, Industry 4.0, particularly the concept of Digital Twins, emerges as a potential avenue for refining processes. To tackle both current and future industry challenges, it is imperative to create a comprehensive methodology capable of generating effective solutions within the waste management sector. This paper provides an explanation of digital twins, outlines the methodological framework comprising an architectural structure and layered model, and details a series of sequential methodical stages for implementing digital twins based on the specific scope determined by the end-user. A noteworthy aspect is the transformative potential of digital twins in enhancing efficiency and precision within waste management practices. By providing a virtual real-time representation of the waste management system, digital twins empower simulations and experimentation to fine-tune processes. Furthermore, they facilitate informed decision-making by offering a detailed visualization of the complete system, simplifying the identification of challenges and opportunities for improvement. that this article derives from the presentation titled "Digital Twin application methodology for the improvement of production and service systems. Application to waste management processes" at the "Sustainable Smart Cities and Territories International Conference" held in the city of Manizales, Colombia, from 21st to 23rd June 2023.

Different types of gold nanoparticles have been synthesized that great potential in medical applications such as medical imaging, bio-analytical sensing and photothermal therapy. However, their stability, polydispersity and biocompatibility are major issues of concern. For example, the synthesis of gold nanorods, obtained through the elongated micelle process, produce them with a high positive surface charge that is cytotoxic. While gold nanoshells are unstable and within a few weeks they decompose due to Ostwald ripening. In this work, we report the self-assembly of the capsid protein of cowpea chlorotic mottle virus (CCMV) around spherical gold nanoparticles, gold nanorods and gold nanoshells to form virus-like particles (VLPs). All gold nanoparticles were synthesized or treated to give them a negative surface charge, so they can interact with the positive N-terminus of the capsid protein leading to the formation of the VLPs. To induce the protein self-assembly around the negative gold nanoparticles, we use different pH and ionic strength conditions that were determined from the capsid protein phase diagram. The encapsidation with the viral capsid protein confers them better biocompatibility, stability, monodispersity and a new biological substrate on which one can introduce specific ligands towards particular cells, broadening the possibilities of medical application.

This paper seeks to optimize the mechanical and durability properties of ultra-high performance concrete (UHPC). To meet this objective, concrete specimens were manufactured by using 1,100 kg/m3 of binder, water/binder ratio 0.20, silica sand and last generation of superplasticizer. Silica fume, metakaolin and two types of nano silica were used for improving the performances of the concrete. Additional mixtures included 13mm long OL steel fibers. Compressive strength, electrical resistivity, mercury intrusion porosimetry tests and differential and thermogravimetric thermal analysis were carried out. The binary combination of nano silica and metakaolin, and the ternary combination of nano silica with metakaolin and silica fume, led to the best performances of the UHPC, both mechanical and durable performances.

Global demand for sleep-tracking wearables, or consumer sleep technologies (CSTs), is steadily increasing. CST marketing campaigns often feature a scientific component, but the scientific relevancy and monetary value of CST features within the sleep research community remains unquantified. Sleep medicine experts were recruited through social media and nonprobability sampling techniques to complete a survey identifying sleep metrics and device features that are most desirable to the scientific community. A hypothetical purchase task (HPT) estimated economic valuation for devices with different features by price. Forty-six (N=46) respondents with an average of 10±6 years’ experience conducting research in real-world settings completed the online survey. Total sleep time was ranked as the most important measure of sleep followed by objective sleep quality while sleep architecture/depth and diagnostic information were ranked as least important. Experts preferred wrist-worn devices that could reliably determine sleep episodes as short as 20 minutes. Economic value was greater for hypothetical devices with longer battery life. These data set a precedent to determine how scientific relevance of a product impacts the potential market value of a CST device. This is the first known attempt to establish consensus opinion or economic valuation for scientifically-desirable CST features and metrics using expert elicitation.

Zinc protection of galvanized steel is initially dissolved in alkaline solutions. However, passive layer is formed over time which protects the steel from corrosion. The behavior of galvanized steel exposed to strong alkaline solutions (pH values of 12.7) with a fixed concentration of sulfate ion of 0.04M is studied. Electrochemical measurement techniques such as corrosion potential, linear polarization resistance and electrochemical impedance spectroscopy are used. Synergistic effect of sulfate ion is also studied together with other anions such as chloride Cl- or bicarbonate ion HCO3- and with other cations such as calcium Ca2+, ammonium NH4+ and magnesium Mg2+. Presence of sulfate ions can depassivate the steel, leading to corrosion density of 0.3 µA/cm2 at the end of the test. The presence of other ions in the solution increases this effect. The increase in corrosion density caused by cations and anions responds to the following order (greater to lesser influence): NH4+&gt;Ca2+&gt;Mg2+ and HCO3- &gt;Cl- &gt;SO42-.

Size effect on plain concrete specimens is well known and can be correctly captured when performing numerical simulations by using a well characterised softening function, but in the case of fibre reinforced concrete this is not directly applicable, since an only diagram cannot capture the material behaviour on elements with different size due to dependence of the orientation factor of the fibres with the size of the specimen. In previous works, the use of a trilinear softening diagram proved to be very convenient for reproducing fracture of polyolefin fibre reinforced concrete elements, but only if it is previously adapted for each specimen size. In this work, a predictive methodology is used to reproduce fracture of polyolefin fibre reinforced concrete specimens of different sizes under three-point bending. Fracture is reproduced by means of a well known embedded cohesive model, with a trilinear softening function that is defined specifically for each specimen size. The fundamental points of these softening functions are defined a priori by using empirical expressions proposed in past works, based on an extensive experimental background. Therefore, the numerical results are obtained in a predictive manner, and then compared with a previous experimental campaign, showing that this approach properly captures the size effect, although some values of the fundamental points in the trilinear diagram could be defined more accurately.

This document presents the design and manufacture of a reflectarray (RA) antenna for the Ku-band, based on a fully-metallic 3D architecture. The reflectarray unit cell is formed by a square-shaped waveguide section ended in a short circuit, that is the reflectarray back ground plane. Each cell has the ability of configuring the phase of its own reflected field by means of resonators perforated on the walls of the cell waveguide section. The resonator-based waveguide cell introduces the 3D character to the design. The geometry of the resonators and its size variation introduces the phase behaviour of each cell, conforming the radiation pattern of the reflectarray. This design explores the potential of phase value truncation (6 states and 2 states), and demonstrates that proper pattern results can be obtained with this phase truncation.

Abstract: The probability of existence or not of local extinctions of six species of carnivorous mammals was analyzed by ordering the species composition in nested subsets in 7 fragments of forest habitats in the Coastal Mountains in the Araucanía Region, in southern Chile. Nested Temperature Calculator (NTC) and BINMATNEST computer programs were used to process the results. The first software provided a temperature in the archipelago of 28.21 degree Celsius, whereas the second program showed a nesting temperature of 16.58 degree Celsius. The computer software used in this study suggest that there is no nesting pattern at the level species composition of carnivorous mammal assemblage in the evaluated area, which may be due to the habitat use characteristics of the different carnivorous mammals studied here.

Plastic flow in body-centered cubic (bcc) alloys is governed by the thermally-activated screw dislocation motion. In bcc interstitial solid solutions, solute diffusion can occur at very fast rates owing to low migration energies and solute concentrations. Under mechanical loading, solutes may move on the same or similar time scale as dislocations glide, even at low temperatures, potentially resulting in very rich co-evolution processes that may have important effects in the overall material response. It is therefore important to accurately quantify the coupling between interstitial impurities and dislocations, so that larger-scale models can correctly account for their (co)evolution. In this paper, we use electronic structure calculations to obtain the energetics of oxygen diffusion under stress and its interaction energy with screw dislocation cores in bcc tungsten. We find that oxygen atoms preferentially migrate from tetrahedral to tetrahedral sites with an energy of 0.2 eV. This energy couples only weakly to hydrostatic and deviatoric deformations, with activation volumes of less than $0.02$ and $0.2b^3$, respectively. The strongest effect is found for the inelastic interaction between O atoms and screw dislocation cores, which leads to attractive energies on the order of 1.5 eV and a structural transformation of the screw dislocation core from an `easy' to a `hard' core configuration

The food distribution process is responsible for significant quality loss in perishable products. However, preserving quality is costly and consumes a tremendous amount of energy. To tackle the challenge of minimizing transportation costs and CO2 emissions while also maximizing product freshness, a novel multi-objective model is proposed. The model integrates a vehicle routing problem with temperature, shelf life, and energy consumption prediction models, thereby enhancing its accuracy. Non-dominated sorting genetic algorithm II is adapted to solve the proposed model for the set of Solomon test data. The conflicting nature of these objectives and the sensitivity of the model to shelf life and shipping container temperature settings are analyzed. The results show that optimizing freshness objective degrade the cost and the emission objectives, and the distribution of perishable foods are sensible to the shelf life of the perishable foods and temperature settings inside the container.

The effects of post-treatment temperature-based methods on 1D single PLA filaments after FFF have been studied. This lets to decouple the variables related to the 3D structure (layer height, raster angle, infill density, and others) from the variables solely related to the material (molecular weight, molecular orientation, crystallinity, and others). PLA 1D filaments have been aged at 20, 39, 42, 51, 65, 75 and 80 ºC in a water-bath-inspired process in which the hydrolytic degradation of the PLA has been minimised for the ageing temperatures of interest. The evolution of the thermal and mechanical properties of the PLA filaments at different temperatures was recorded. Differential scanning calorimetry (DSC) was used to evaluate thermal and physical properties, in which the glass transition, enthalpic relaxation, crystallisation and melting reactions were analysed. Tensile tests were performed to evaluate the tensile strength and elastic modulus. The flow-induced molecular orientation, the degradation, the logistic fitting and the so-called summer effect –stabilisation of properties at higher temperatures– are discussed for assessing the safeness of accelerating ageing.

This paper aims to provide the smart grid research community with an open and accessible general mathematical framework to develop and implement optimal flexibility mechanisms in large-scale network applications. The motivation of this paper is twofold. On the one hand, flexibility mechanisms are currently a hot topic of research, which is aimed to mitigate variation and uncertainty of electricity demand and supply in decentralised grids with a high aggregated share of renewables. On the other hand, a large part of such related research is performed by heuristic methods, which are generally inefficient (such methods do not guarantee optimality) and difficult to extrapolate for different use cases. Alternatively, this paper presents an MPC-based (Model Predictive Control) framework explicitly including a generic flexibility mechanism which is easy to particularise to specific strategies such as Demand Response, Flexible Production and Energy Efficiency Services. The proposed framework is benchmarked with other non-optimal control configurations to better show the advantages it provides. The work of this paper is completed by the implementation of a generic use case which aims to further clarify the use of the framework and thus, to ease its adoption by other researchers in their specific flexibility mechanisms applications.

This paper investigates the use of deep learning techniques to perform energy demand forecasting. Specifically, the authors have adapted a deep neural network originally thought for image classification and composed of a convolutional neural network (CNN) followed by a multilayered fully connected artificial neural network (ANN). The convolutional part of the network was fed with a grid of temperature forecasting data distributed in the area of interest in order to extract a featured temperature. The subsequent ANN is then fed with this calculated temperature along with other data related to the timing of the forecast. The proposed structure was first trained and then used in a real setting aimed to provide the French energy demand forecast using ARPEGE forecasting weather data. The results show that the performance of this approach is in the line of the performance provided by the reference RTE subscription-based service, which opens the possibility to obtain high accuracy forecasting using widely accessible deep learning techniques through open-source machine learning platforms.

Fibre reinforced cementitious materials (FRC) have become an attractive alternative for structural applications. Among such FRC, steel and polyolefin fibre reinforced concrete and glass fibre reinforced concrete are the most used ones. However, in order to exploit the properties of such materials structural designers need constitutive relations that reproduce FRC fracture behaviour accurately. This contribution analyses the suitability of multilinear softening functions combined with a cohesive crack approach for reproducing the fracture behaviour of the FRC previously mentioned. The implementation performed accurately simulates the fracture behaviour while being versatile, robust and efficient from a numerical point of view.

The determination of the parameters that characterise the air-void system in hardened concrete elements becomes crucial for structures under freezing and thawing cycles. The ASTM C457 standard describes some procedures to accomplish this task, but they are not easy to apply, require specialised equipment such as a stereoscopic microscope and result in highly tedious tasks to be performed. This paper describes an alternative procedure to the modified point-count method described in the Standard that makes use of macro photography. This alternative procedure is successfully applied to a large set of samples and presents some advantages over the traditional method, since the required equipment is less expensive and provides a more comfortable and less tedious procedure for the operator.

The effect of graphene oxide (GO) on mechanical strengths and durability of cement composites has been studied by preparing GO-modified cement mortars. Thermogravimetric analysis (TGA) and nuclear magnetic resonance (29Si MAS-NMR) were performed on the cement paste to research the influence of GO on the hydration process and chain structure of calcium-silicate-hydrate (C-S-H) gels. In addition, mechanical strength test, such as compressive and flexural, were performed on cement mortars. The addition of GO at 0.05 wt.% (by weight of cement) increased the compressive strength by 9.02% after 28 days. Furthermore, the flexural strength of cement mortars with 0.05 wt.% GO and superplasticizer (SP) after 7 and 28 days increased by 12.26% and 21.86%, respectively, compared with reference mortar. At the same time, the effect of GO proved to be more significant and effective in the durability tests, suggesting that GO can enhance the microstructure through hydration products to create a highly cross-linked micro structure.

Three autonomous communities have been the ones that, in the 2022-2023 season, anticipated the document approved by the Public Health Commission, recommending influenza vaccination for all children aged 6 to 59 months. The main objective of this work is to evaluate the attitude of healthcare professionals towards the first universal vaccination campaign in our region, as well as the acceptability of the vaccines used and the attitude towards the piloting of school vaccination. Cross-sectional, survey-based, descriptive study. All healthcare professionals involved in the campaign were invited to participate. The 91.9% of surveyed professionals thought that flu vaccination from 6 to 59 months was important or very important. 89.8% had previous experience regarding the intramuscular vaccine. The professionals valued the intranasal vaccine significantly more positively; however, there were no differences when asking for each of the vaccines without comparison. The inhaled vaccine was preferred by 97.5% for the following campaign. Piloted school vaccination showed 75% acceptance. The inhaled vaccine was preferred by most professionals and the piloted school vaccination was highly accepted, and independently associated to the importance of vaccination as considered by physicians, being a medical doctor, and participation in the pilot program.

This paper presents an alternative constraint handling approach within a specialized genetic algorithm (SGA) for the optimal reactive power dispatch (ORPD) problem. The ORPD is formulated as a nonlinear single-objective optimization problem aiming to minimize power losses while keeping network constraints. The proposed constraint handling approach is based on a product of sub-functions that represents permissible limits on system variables and that includes a specific goal on power loss reduction. The main advantage of this approach is the fact that it allows a straightforward verification of both feasibility and optimality. The SGA is examined and tested with the proposed constraint handling approach and the traditional penalization of deviations from feasible solutions. Several tests are run in the IEEE 30, 57, 118 and 300 bus test power systems. The results obtained with the proposed approach are compared to those offered by other metaheuristic techniques reported in the specialized literature. Simulation results indicate that the proposed genetic algorithm with the alternative constraint handling approach yields superior solutions when compared to other recently reported techniques.

Existence of hybrid electric vehicles nowadays is one of the emerging technologies worldwide. Different countries are using this technology on their transportation, and nowadays, a lot of other countries are gradually adapting on using this kind of innovation in their transport system. Philippines is among these countries which aims to have a sustainable mobility by embracing the use of hybrid - electric vehicles but still lots of consumers are lacking awareness on this technology. Lack of information on the social, environmental, and economic potential benefits are among the main issues of Philippines consumers that really affect its uptake. The goal of this study was to evaluate the consumer’s perception and purchase intention on the transition of hybrid - electric vehicles for sustainable mobility and transportation here in the Philippines. It aimed to assess consumer awareness with hybrid - electric vehicles and its potential benefits to human beings in terms of social, environmental, and economic aspects. The study also gauged the impact of this perception on consumer’s purchase intention on hybrid - electric vehicles. These objectives were attained using the Descriptive Statistics and Correlation Analysis. Using these methods, the results revealed that majority of the consumers believed on the positive benefits of transitioning to hybrid - electric vehicles in terms of social, environmental, and economic aspects. This study also showed that these benefits have high impact on the consumer’s intention of buying or having a hybrid – electric vehicle. Electric vehicle is one of the most effective measure of decarbonizing the transport system. Furthermore, government and automotive businesses must strengthen their drive in spreading awareness of hybrid – electric vehicle’s benefits to consumers to further support country’s effort for development.

Connexins (Cxs) are transmembrane proteins that assemble into gap junction channels (GJCs) and hemichannels (HCs). Previous research supports the involvement of Rho GTPases and actin microfilaments in the trafficking of Cxs, formation of GJCs plaques, and regulation of channel activity. Nonetheless, it remains uncertain whether distinct types of Cxs HCs and GJCs respond differently to Rho GTPases or changes in actin polymerization/depolymerization dynamics. Our investigation revealed that inhibiting RhoA, a small GTPase that controls actin polymerization, or disrupting actin microfilaments with cytochalasin B (Cyto-B), resulted in reduced GJCs plaque size at appositional membranes and increased transport of HCs to non-appositional plasma membrane regions. Notably, these effects were consistent across different Cx types, since Cx26 and Cx43 exhibited similar responses despite having distinct trafficking routes to the plasma membrane. Functional assessments showed that RhoA inhibition and actin depolymerization decreased the activity of Cx43 GJCs while significantly increasing HCs activity. However, the functional status of GJCs and HCs composed of Cx26 remained unaffected. This study supports the hypothesis that RhoA, through its control of the actin cytoskeleton, facilitates the transport of HCs to appositional cell membranes for GJCs formation while simultaneously limiting the positioning of free HCs at non-appositional cell membranes, independently of Cx type. This dynamic regulation promotes intercellular communication and reduces non-selective plasma membrane permeability through a Cx-type dependent mechanism, whereby Cx43 HCs and GJCs are affected, but Cx26 channels are not.

The effect of Mg particles on PLA's thermal, chemical, physical, and mechanical properties has been studied. The thermal and physical properties have been studied by differential scanning calorimetry, analysing the stability of the α and α’-crystals of the PLA. A colloidal route was used to introduce Mg particles inside the PLA matrix, ensuring a good dispersion of the particles. Materials with Mg contents from 0 to 10 wt.% have been prepared, with additions of polyethyleneimine (PEI) and polyethylene glycol (PEG). Fourier Transform Infrared Spectroscopy has been used to confirm the influence of Mg, PEI, and PEG on PLA properties. The mechanical properties have been measured with a universal tensile test machine on printed filaments via Fused Filament Fabrication (FFF), which were naturally aged to stable conditions. Filaments with and without a notch were studied to obtain the materials' tensile strength, elastic modulus, and fracture toughness. Different analytical models to explain the results of the PLA-Mg were studied, in which the interface strength of the PLA-Mg composites was calculated.

Steel fibers (SF) and polyolefin (PF) are widely used for shotcrete, especially in tunnelling. Both SF and PF and have shown to meet the standards in order to reduce or substitute the conventional steel mesh as reinforcement of concrete showing mechanical and productive advantages. This study sought the analysis and assessment of the mechanical properties of fiber reinforced shotcrete, comparing in-situ with laboratory results. This was performed with low and high fiber dosages of SF and PF as well as a combination of them (hybrid mixtures). A total of seven mixtures, two of steel, two of polyolefins, two hybrids and a control mixture were manufactured at laboratory and in situ. By performing tests according to EN 14651 and slabs according to EN 14488-5, it was possible to characterize the residual flexural strengths (fRj), and energy absorption capacity (E25mm) in slabs. In addition, a fracture surface analysis was performed, and the orientation factor was obtained. This allowed the authors to quantify the loss of residual strength on site and correlate it with the fiber content and positioning. Moreover, some relationships between beam and slab tests were found, allowing to correlate the most relevant type of tests in the field of fiber reinforced concrete.

The sugar company Valdez S.A. Entity located within the geographical limits of the city of Milagro, needs to reduce its emissions to the environment and does not always comply with the air emissions standards for stationary combustion sources, which indicates that for equipment installed before 2003 they have a maximum limit of 300 mg / m³. A mist eliminator was designed to work inside the original wet gas scrubber of the water-tube cauldron #10, which uses Bagasse as fuel, for the generation of steam for industrial use. The research is documentary and field. The methodology used was mixed. focusing on the comparison of three types of technologies to meet the objectives, the fog eliminators types: Demister, Cyclone and Chevron. To find the appropriate complement, a comparison sheet was made, which is a table of contents evaluated quantitatively, analyzing indicators formulated in each of the contents. The results, supported by the Multiple Criteria Decision Analysis methodology, select the Chevron type fog eliminator, with the best efficiency for capture. Using AutoCAD, allows to visualize in 3D, the structural design in the gas scrubber.

Fibre reinforced concrete (FRC) has been used for decades in certain applications of the construction industry, such as tunnel linings and precast elements, but has experienced an important progress in recent times, boosted by the inclusion of guidelines for their use in some national and international standards. Traditional steel fibres have been studied in depth and their performance is well known although in recent years new materials have been proposed as possible alternatives. Polyolefin macro-fibres, for instance, have proven to enhance the mechanical properties of concrete and the parameters that define their behaviour (fibre length, fibre proportion or casting method, for instance) have been identified. These fibres overcome certain traditional problems related to steel fibres, such as corrosion or their interaction with magnetic fields, which can limit the use of steel in some applications. The behaviour of polyolefin fibre reinforce concrete (PFRC) has been numerically reproduced with success through an embedded cohesive crack formulation that uses a trilinear softening diagram to describe the fracture behaviour of the material. Furthermore, concrete behaves well under high temperatures or fire events, especially when it is compared with other construction materials, but the behaviour of PFRC must be analysed if the use of these fibres is to be extended. To this end, the degradation of PFRC fracture properties has been recently experimentally analysed under a temperature range between 20ºC and 200ºC. As temperature increases, polyolefin fibres modify their mechanical properties and their shape, which reduce their performance as reinforcement of concrete. In this work, those experimental results, which include results of low (3 kg/m3) and high (10 kg/m3) proportion PFRC specimens, are used as reference to study the fracture behaviour of PFRC exposed to high temperatures from a numerical point of view. The experimental load-deflection diagrams are reproduced by modifying the trilinear diagram used in the cohesive model, which helps to understand how the trilinear diagram parameters are affected by high temperature exposure. Finally, some expressions are proposed to adapt the initial trilinear diagram (obtained with specimens not exposed to high temperature) in order to numerically reproduce the fracture behaviour of PFRC affected by high temperature exposure.

Groundwater degradation is a global problem linked to irrigation agriculture and aggravated by climate change. In drylands, where aquifer recharge is low, irrigation has emerged as an engine of economic growth. This problem falls under the paradigm of desertification, as it fits the definition of this complex problem in that the degradation of drylands is due to climatic variations and inappropriate human activities. Land Degradation Neutrality (LDN), the response of the United Nations Convention to Combat Desertification to the lack of progress in tackling desertification, is integrated into Sustainable Development Goal 15.3 and provides the adequate framework for implementing effective solutions. LDN prioritizes prevention strategies, and early warning systems coupled to integrated simulation models is a sound approach. We analyze the dynamics of a coastal aquifer in southern Spain, a “desertification landscape” according to the Spanish National Action Plan to Combat Desertification. For this purpose, we have (i) adapted a generic desertification model that considers socio-ecological systems as a particular case of predator-prey systems; and (ii) coupled to this model a risk analysis to calculate the probabilities of groundwater salinization under the current scenario of water resources use, driven by the expansion of greenhouse agriculture supported by external water transfer. The risk of desertification is close to 100%: groundwater salinity is 40 dS m-1 (well above tomato tolerance, 3.5 dS m-1), and 2.4 Mm3 yr–1 water transfer is needed to support the 631 ha of greenhouses. This worrying result suggests that complimentary solutions should be promoted to deactivate the ongoing process of desertification. Among them, we propose reclaimed water, diversifying the economy, or promoting crops adapted to aridity. This simulation framework shows how to explore the future of a socio-ecosystem under current scenarios and others that consider climate change, the energy crisis, or the impact of alternative solutions.

This paper describes the packaging models that are fundamental for the design of ultra-high-performance concrete (UHPC), and their evolution. They are divided into two large groups: continuous and discrete models. The latter are those that provide the best answer in obtaining an adequate simulation of the packing of the particles up to nanometric size. This includes the interaction among the particles by means of loosening and wall coefficients, allowing a simulation of the virtual and real compactness of such particles. In addition, a relationship between virtual and real compactness is obtained, through the compaction index, which may simulate the energy of compaction that the particles undergo in their placement in the mold. The use of last-generation additives allows such models to be implemented with water-cement (w/c) ratios close to 0.18. However, the premise of maximum packing as a basic pillar for the production of UHPC should not be the only one. The cement hydration process affected by nanoadditions and the ensuing effectiveness in the properties in both fresh and hardened state according to the respective percentages in the mixture should also be studied. An adequate ratio and proportion of these additions may lead to an obtaining of better results even with lower levels of compactness.

Concrete has become the most common construction material showing among other advantages good behaviour when subjected to high temperatures. Nevertheless, concrete is usually reinforced with elements of other materials such as steel in the form of rebars or fibres. Thus, the behaviour under high temperatures of these other materials can be critical for structural elements. In addition, concrete spalling occurs when concrete is subjected to high temperature due to internal pressures. Micro polypropylene fibres (PP) have shown to be effective for reducing such spalling although this type of fibres barely improve any of the mechanical properties of the element. Hence, a combination of PP with steel rebars or fibres can be effective for the structural design of elements exposed to high temperatures. New polyolefin fibres (PF) have become an alternative to steel fibres. PF meet the requirements of the standards to consider the contributions of the fibres in the structural design. However, there is a lack of evidence about the behaviour of PF and elements made of polyolefin fibre reinforced concrete (PFRC) subjected to high temperatures. Given that these polymer fibres would be melt above 250 °C, the behaviour in the intermediate temperatures was assessed in this study. Uni-axial tests on individual fibres and three-point bending tests of PFRC specimens were performed. The results have shown that the residual load-bearing capacity of the material is gradually lost up to 200 °C, though the PFRC showed structural performance up to 185°C.

This work proposes a novel methodology for the complete characterization of fiber reinforced concrete (FRC). The method includes bending tests of prismatic notched specimens, based on the Standards for FRC, tensile and pure shear tests. The values adopted by the standards for designing FRC are the obtained from bending tests, typically fR3, even for shear and pure tension loading. This paper shows that the remaining strength of FRC, supplied by the fibers, depends on the type of loading. In the case of shear and tensile loading the prescriptions of the standards may be unsafe. In this work, the remaining halves of specimens subjected to bending test are prepared and used for shear and tension tests. This means significant savings in specimen preparation and a greater amount of information for structural use of FRC. The results provide relevant information for the design of structural elements of FRC compared with the only use of data supplied by bending tests. In addition, a video-extensometry system was used to analyze the crack generation and cracking patterns. The video-extensometry applied to shear tests allowed the assessment of the sliding values and crack opening values at the crack discontinuity. These values may be quite relevant for the study of the FRC behavior when subjected to shear according to the shear-friction model theories.

Chagas disease (CD) is one of the most devasting parasitic diseases in the Americas affecting 7 to 8 million people worldwide. In vitro and in vivo experiments have demonstrated that decreased growth hormone (GH) serum levels occur as CD progresses. Interestingly, inactivating mutations in the GH receptor in humans induce Laron syndrome (LS), a clinical entity characterized by increased GH and decreased insulin growth factor-1 (IGF-1) serum levels. The largest cohort of LS subjects lives in the southern provinces of Ecuador. Remarkably, CD prevalence in these individuals is diminished despite living in highly endemic areas. In the current ex vivo study, we employed serum from GHR -/- mice, also known as LS mice (a model of GH resistance with high GH and low IGF-1 levels), and serum from bovine GH (bGH) transgenic mice (high GH and IGF-1), to test the effect on T. cruzi infection. We infected mouse fibroblast L-cells treated with serum from each type of mouse with metacyclic trypomastigotes from Trypanosoma cruzi (etiological CD infectious agent). Treatment with GHR-/- serum (LS mice) significantly decreased infection by 28% compared to 48% seen in control wild-type mouse serum (WT). Treatment with bGH mouse serum significantly decreased infection by only 41% compared to 54% from WT controls. Our results suggest that high GH and low IGF-1 in blood circulation, as typically seen in LS individuals, confers partial protection against T. cruzi infection.

Viral diseases pose a significant threat to tomato crops (Solanum lycopersicum L.), one of the world's most economically important vegetable crops. The limited genetic diversity of cultivated tomatoes contributes to their high susceptibility to viral infections. To address this challenge, tomato breeding programs must harness the genetic resources found in native populations and wild relatives. Breeding efforts may aim to develop broad-spectrum resistance against the virome. To identify the viruses naturally infecting 19 advanced lines, derived from native tomatoes, high-throughput sequencing (HTS) of small RNAs and validation by PCR and RT-PCR were used. Single and mixed infections with Tomato mosaic virus (ToMV), Tomato golden mosaic virus (ToGMoV), and Pepper huasteco yellow vein virus (PHYVV) were detected. The complete consensus genomes of three variants of Mexican ToMV isolates were reconstructed, potentially forming a new ToMV clade with a distinct 3' UTR. The absence of reported mutations associated with resistance-breaking to ToMV suggests that the Tm-1, Tm-2, and Tm-22 genes could theoretically be used to confer resistance. However, the high mutation rates and a 63 nucleotide insertion in the 3' UTR of Mexican ToMV isolates suggest the need to evaluate known resistance genes against these viral variants. The precise identification and characterization of viruses that naturally infect tomato germplasm could be used as a strategy for selecting the appropriate disease management and guiding breeding efforts.

The goal of this report was to examine the behavioral economic demand for consumer sleep technologies with different levels of validation and endorsement. The value or importance consumers place in different validation methods and the organizations conducting the evaluations was also assessed. Survey data were collected from 113 participants on Amazon mTurk. Participants indicated their likelihood of purchasing devices that varied in level of validation across a series of increasing prices. Demand curves were analyzed to determine the relative value of each watch type. Participants also reported how valuable or important different aspects of device validation were to them. Devices that were both evaluated against laboratory measures and endorsed by sleep researchers had the most value, followed by those only evaluated against laboratory measures, and then those not evaluated against any laboratory measures. The unit price at which there was 50% probability of purchase was increased by $25 or $44 for evaluation or endorsement, respectively. Respondents indicated the most valuable features were a measure of sleep duration, that it was most important that devices were validated against measures of sleep from a laboratory or hospital, and that they would put a high value on sleep tracker endorsements from a university or academic institution. Consumer demand is greatest for a device that has been evaluated by an independent laboratory for accuracy in measuring sleep and is endorsed by an academic, medical, or government institution. These results indicate a role for scientific evaluation and endorsement in consumer preference for sleep trackers.

Fibre reinforced concrete (FRC) has become an alternative for structural applications due its outstanding mechanical properties. The appearance of new types of fibres and the fibre cocktails that can be configured mixing them has created FRC that clearly exceed the minimum mechanical properties required in the standards. Consequently, in order to take full advantage of the contribution of the fibres in construction projects, it is of great interest to have constitutive models that simulate the behaviour of the materials. This study aimed to simulate the fracture behaviour of five types of FRC, three with steel hooked fibres, one with a combination of two types of steel fibres and one with a combination of polyolefin fibres and two types of steel fibres, by means of an inverse analysis based on the cohesive crack approach. The results of the numerical simulations defined the softening functions of each FRC formulation and have pointed out the synergies that are created through use of fibre cocktails. The information obtained might suppose a remarkable advance for designers using high-performance FRC in structural elements.

Current antibiograms cannot discern the particular effect of a specific antibiotic when the bacteria are incubated with a mixture of antibiotics. To prove that this task is achievable, Escherichia coli strains were treated with ciprofloxacin for 45 min, immobilized on a slide and stained with SYBR Gold. In susceptible strains, the nucleoid relative surface started to decrease near the MIC, being progressively condensed as dose increased. The shrinkage level correlated with the DNA fragmentation degree. Ciprofloxacin-resistant bacilli showed no change. Additionally, E. coli strains were incubated with ampicillin for 45 min and processed similarly. The ampicillin-susceptible strain revealed intercellular DNA fragments that increased with dose, unlike the resistant strain. Co-incubation with both antibiotics revealed that ampicillin did not modify the nucleoid condensation effect of ciprofloxacin, whereas the quinolone partially decreased the background of DNA fragments induced by ampicillin. Sixty clinical isolates, with different combinations of susceptibility-resistance to each antibiotic, were co-incubated with the EUCAST breakpoints of susceptibility of ciprofloxacin and ampicillin. The morphological assay correctly categorized all the strains for each antibiotic in 60 min, demonstrating the feasible independent evaluation of a mixture of quinolone and beta-lactam. The rapid phenotypic assay may shorten the incubation times and necessary microbial mass currently required for evaluation.

To assess the clinical efficacy of a novel organic olive oil-based denture adhesive and its effect on Candida Albicans growth in maxillary edentulous individuals wearing complete dentures. Individuals were selected from two Dental Schools in Portugal and Spain. Twenty-eight complete dentures were relined, following a standardized protocol. The novel product (Test) was compared with a commercialized adhesive (Control) and Vaseline (Placebo) randomly assigned in a cross-study design. The retention resistance was measured with a Gnathometer and a dynamometer, the patient related outcome evaluations with a 5-points questionnaire and the Candida albicans growth in a Sabouraud dextrose agar (SDA) medium in order to evaluate differences between the placebo and experimental product. Twenty-three participants were included. Dynamometer evaluation showed significant differences between not using a denture adhesive and using either (experimental, p = .03; control, p = .04), no significant differences between the two adhesives (p &gt; .05). In the subjective analysis, the experimental adhesive showed a significantly longer effectiveness (p = .001); the control reported better results at taste (p = .03) in chewing (p = .001). The test adhesive showed better (p &lt; .001) Candida albicans growth inhibition. The experimental adhesive showed longer effectiveness than the control and placebo with a better inhibition capacity for the growth of Candida albicans, patients reported better abilities for speech, chewing, taste and retirement in the control adhesive.

In 2007, the excavation of the M-30 ring road located in Madrid and the creation of a green corridor either side of the Manzanares river brought significant change to the metropolitan area. The corridor and linear park which it provided were designed to contribute to the regeneration of the fluvial ecosystem, establish links among residents on each side of the river and promote cultural and leisure activities. This paper provides a sustainability analysis of the excavation of the M-30 (involving the socio-economic and environmental impact) 14 years after its construction. In order to show such an impact, an analysis of the area both prior to the project and after completion, as well as a hypothetical solution that uses improved materials, has been performed. This entails use of the multi-criteria decision-making model named MIVES (initials in Spanish, modelo integrado de valor para una evaluación sostenible). The MIVES method is based on the application of value functions of sustainability indicators selected by socio-economic and environmental criteria, chosen by experts. Results from analysis showed that the excavation of the M-30 considerably improved the sustainability of the area (sustainable index 3.43 and 6.26 both before and after the excavation works). However, use of improved materials in contrast with the application of conventional materials slightly improved the sustainability of the work (Sustainability Index 6.26 and 6.74, respectively, of the conventional materials).

Intelligent transportation systems (ITS) are at the forefront of advancements in transportation, offering enhanced efficiency, safety, and environmental friendliness. To enable ITS, autonomous systems play a pivotal role, leveraging breakthroughs in autonomous driving, data-driven modeling, and multiagent control strategies to establish sustainable and coordinated traffic management. The integration of connected and automated vehicles has garnered significant attention as a potential solution for alleviating traffic congestion and improving fuel economy, achieved through global route optimization and cooperative driving. This study focuses on a predictive control perspective to address the cooperative cruise control problem. Online decision-making is employed during the driving process, utilizing information gathered from the network. By employing bargaining games to establish an operating agreement among vehicles, we formalize a synchronization approach based on predictive control theory. Ultimately, these findings are put to the test in an emulation environment within a hardware-in-the-loop system.

In this work 144 reinforcing bars of high-ductility steel named B500SD were subjected to an accelerated corrosion treatment and then tested under tension at different loading speeds in order to assess the effect of corrosion on the ductility properties of the rebars. Results showed that the bars with a corrosion level as low as the one reducing the steel mass by 1% gave rise to a significant degradation on the ductility properties with strain-stress curves losing the yield plateau and behaving practically as cold deformed steel bars. This effect took place at every tested loading speed. Thus, the research significance relies on the assessment of the influence of the loading speed at which the tensile test is performed given that it affects the ductility properties of the reinforcement bars.

Construction involves the use of significant quantities of raw materials and entails high-energy consumption. For the sake of choosing the most appropriate solution that considers environmental and sustainable concepts, tools such as the integrated value model for sustainable assessment (Modelo Integrado de Valor para una Evaluación Sostenible, MIVES) used in Spain, plays a key role in obtaining the best solution. MIVES is a multi-criteria decision-making method based on the value function concept and the seminars delivered by experts. Such tools, in order to show how they may work, require application to case studies. In this paper, two concrete slabs manufactured with differing reinforcement during the construction of the La Canda Tunnels are compared by means of MIVES. The two concrete slabs were reinforced with a conventional steel-mesh and with polyolefin fibres. The results showed that from the point of view of sustainability, the use of polyolefin fibres provided a significant advantage mainly due to the lower maintenance required.

The neocortex is an exquisitely organized structure achieved through complex cellular processes from the generation of neural cells to their integration into cortical circuits after complex migration processes. During this long journey, neural cells need to stablish and release adhesive interactions through cell surface receptors known as cell adhesion molecules (CAMs). Several types of CAMs have been described regulating different aspects of neurodevelopment. Whereas some of them mediate interactions with the extracellular matrix, others allow contacts with additional cells. In this review, we will focus on the role of two important families of cell-cell adhesion molecules (C-CAMs), classical cadherins and nectins, as well as in their effectors, in the control of fundamental processes related with corticogenesis, with especial attention in the cooperative actions among the two families of C-CAMs.

This work is intended to lead a study of necessary and sufficient optimality conditions for scalar optimization problems on Hadamard manifolds. In the context of this geometry, we obtain and present new function types characterized by the property of having all their second-order stationary points to be global minimums. In order to do so, we extend the concept convexity in Euclidean space to a more general notion of invexity on Hadamard manifolds. This is done employing notions of second-order directional derivative, second-order pseudoinvexity functions and the second-order Karush-Kuhn-Tucker-pseudoinvexity problem. Thus, we prove that every second-order stationary point is a global minimum if and only if the problem is either second-order pseudoinvex or second-order KKT-pseudoinvex depending on whether the problem regards unconstrained or constrained scalar optimization respectively. This result has not been presented in the literature before. Finally, examples of these new characterizations are provided in the context of \textit{"Higgs Boson like"} potentials among others.

Tomato is considered moderately sensitive to salinity, which detracts from the quality and yield of its fruit; therefore, wild populations have been used as a genetic resource. The aim of this research was to identify lines derived from wild tomato populations with tolerance to salinity during the germination and seedling stages. During germination, 52 wild lines and 2 commercial hybrids (Imperial®, Reserva®) were subjected to 150 mM and 0 mM NaCl and evaluated. The test was carried out for 20 days in a germination chamber with constant darkness, temperature of 25±2 °C and relative humidity of 80±4%. At the seedling stage, 22 wild tomato lines with the best performance in the germination test and 2 commercial hybrids (Imperial®, Topanga®) were evaluated for 12 days in a floating raft system. Concentrations of 175 mM and 0 mM NaCl were used. During germination, the saline condition decreased germination percentage (65.2%), speed of germination (88.2%), steam length (72.5%), root length (46.56%), normal plants number (59.5%), stem dry matter (68.78%), root dry matter (61.99%), and total dry matter (67.1%). At the seedling stage, this condition decreased (P<0.05) the aerial part dry matter (46.37%), leaf area (59.35%), root length (42.43%), final plant height (40.24%), and growth rate (71.42%). Seventeen tolerant genotypes were identified at one of both developmental stages, while one genotype showed tolerance at both stages. These results indicate that there are different response mechanisms in each developmental stage. Native tomatoes play an important role in the identification of tolerant genotypes since they can be used as genetic resources for obtaining commercial genotypes with salt tolerance.

Business Intelligence, defined by [1] as "the ability to understand the interrelations of the facts that are presented in such a way that it can guide the action towards achieving a desired goal", has been used since 1958 for the transformation of data into information, and of information into knowledge, to be used when making decisions in a business environment. But, what would happen if we took the same principles of business intelligence and applied them to the academic environment? The answer would be the creation of Academic Analytics, a term defined by [2] as the process of evaluating and analyzing organizational information from university systems for reporting and making decisions, whose characteristics allow it to be used more and more in institutions, since the information they accumulate about their students and teachers gathers data such as academic performance, student success, persistence, and retention [5]. Academic Analytics enables an analysis of data that is very important for making decisions in the educational institutional environment, aggregating valuable information in the academic research activity and providing easy to use business intelligence tools. This article shows a proposal for creating an information system based on Academic Analytics, using ASP.Net technology and trusting storage in the database engine Microsoft SQL Server, designing a model that is supported by Academic Analytics for the collection and analysis of data from the information systems of educational institutions. The idea that was conceived proposes a system that is capable of displaying statistics on the historical data of students and teachers taken over academic periods, without having direct access to institutional databases, with the purpose of gathering the information that the director, the teacher, and finally the student need for making decisions. The model was validated with information taken from students and teachers during the last five years, and the export format of the data was pdf, csv, and xls files. The findings allow us to state that it is extremely important to analyze the data that is in the information systems of the educational institutions for making decisions. After the validation of the model, it was established that it is a must for students to know the reports of their academic performance in order to carry out a process of self-evaluation, as well as for teachers to be able to see the results of the data obtained in order to carry out processes of self-evaluation, and adaptation of content and dynamics in the classrooms, and finally for the head of the program to make decisions.

The use of pain relief during castration and dehorning of calves on commercial beef operations can be limited by constraints associated with the delivery of analgesic agents. As topical anaesthetic (TA) and buccal meloxicam (MEL) are now available in Australia, offering practical analgesic treatments for concurrent castration and dehorning of beef calves, a study was conducted to determine their efficacy in providing pain relief when applied alone or in combination. Weaner calves were randomly allocated to; (1) no castration and dehorning / positive control (CONP); (2) castration and dehorning / negative control (CONN); (3) castration and dehorning with buccal meloxicam (BM); (4) castration and dehorning with topical anaesthetic (TA); and (5) castration and dehorning with buccal meloxicam and topical anaesthetic (BMTA). Weight gain, paddock utilisation, lying activity and behaviour following treatment were measured. CONP and BMTA calves had significantly greater weight gain than CONN calves (P < 0.001). CONN calves spent less time lying compared to BMTA calves on all days (P < 0.001). All dehorned and castrated calves spent more time walking (P = 0.024) and less time eating (P < 0.001) compared to CONP calves. There was a trend for CONP calves to spend the most time standing and CONN calves to spend the least time standing (P = 0.059). There were also trends for the frequency of head turns to be lowest in CONP and BMTA calves (P = 0.098) and tail flicks to be highest in CONN and BM calves (P = 0.061). The findings of this study suggest that TA and MEL can improve welfare and production of calves following surgical castration and amputation dehorning.

The purpose of this research has been to analyze the organizational structures of the different federations and entities representing the modalities of trail-running, skyrunning and mountain running and how they have settled in the current sports landscape. The main task of these entities is to act as hosts of the legally established modalities, both internationally and nationally, applying their respective regulations and statutes unilaterally. Through an in-depth review of the different regulations, statutes and current articles of all the organizations that represent the different disciplines, we can observe how a sport modality that seems to be the same is nevertheless distant in its execution (regulations, championships, classifications, systems of points, ...) and that has led to the international level being established in different sport modalities (trail-running and skyrunning) and at the level of the Spanish territory, it has led to an administrative dispute to know who has the powers to approve the sports competitions.

This paper analyses the evolution of the internal damage in two types of steel that show different fracture behaviours, with one of them being the initial material used for manufacturing prestressing steel wires, which shows a flat fracture surface perpendicular to the loading direction, and the other one being a standard steel used in reinforced concrete structures, which shows the typical cup-cone surface. 3mm-diameter cylindrical specimens are tested with a tensile test carried out in several loading stages and, after each of them, unloaded and analysed with X-ray tomography, which allows detection of internal damage throughout the tensile test. In the steel used for reinforcement, damage is developed progressively in the whole specimen, as predicted by Gurson-type models, while in the steel used for manufacturing prestressing steel-wire damage is developed only in the very last part of the test. In addition to the experimental study, a numerical analysis is carried out by means of the finite element method by using a Gurson model to reproduce the material behaviour.

Renewable methanol, obtained from CO₂ and hydrogen provided from renewable energy, has been proposed as a way to close the CO₂ loop. In industry, methanol synthesis using the catalyst CuO/ZnO/Al₂O₃ occurs at a high pressure. We intend to make certain modification on the traditional catalyst in order to work at lower pressure, maintaining high selectivity. Therefore, three heterogeneous catalysts have been synthesized by co-precipitation in order to improve the activity and the selectivity to methanol under mild conditions of temperature and pressure. Certain modifications on the traditional catalyst Cu/Zn/Al₂O₃ were employed such as the modification of the synthesis time and the addition of Pd as a dopant agent. The most efficient catalyst among those tested was a palladium-doped catalyst, 5% Pd/Cu/Zn/Al₂O₃. This had a selectivity of 64% at 210C and 5 bar.

This paper presents the design of a new neuro-generator of pseudorandom number type PRNG Pseudorandom Number Generator, which produces complex sequences with an adequate bit distri-bution. The circuit is connected to a neuronal module with six impulse neurons with different be-haviors: spike frequency adaptation, phasic spiking, mixed mode, phasic bursting, tonic bursting and tonic spiking. This module aims to generate a non-periodic signal that becomes the clock sig-nal for one of the LFSRs Linear Feedback Shift Register that the neuro-generator has. To verify its correct operation, the neuro-generator was subjected to a series of tests where the frequencies of the impulse neurons were modified. This modification allows generating a greater number of pulses at the output of the neuronal module, to obtain sequences with different characteristics that pass different NIST statistical tests National Institute of Standards and Technology of U.S. The results show that the new neuro-generator maintains pseudo-randomness in the sequences obtained with different frequencies and it can be implemented on reconfigurable FPGA Field Programmable Gate Array Virtex 7 xc7vx85t-2ffg1761 device. Therefore, it can be used for applications such as biologi-cal systems.

In this paper we show the results of investigating the presence of organochlorine pesticides in honey and pollen samples from managed colonies of the honey bee, Apis mellifera L. and of the stingless bee Scaptotrigona Mexicana Guérin. We found that 88.44% and 93.33% of honey samples, and 22.22% and 100% of pollen samples of S. mexicana and A. mellifera, respectively, resulted positive to at least one organochlorine. The most abundant pesticides were DDE, DDT, Endrin and heptaclor. Despite the low foraging range of S. mexicana the number of pesticides detected in the honey samples was similar to that of A. mellifera. Paradoxically we a found a small number of organochlorines in pollen samples of S. mexicana, perhaps indicating a rapid turnover of this material as compared to A. mellifera.

In this work, the transport equations of ionic species in concrete are studied. First, the equations at the porescale are considered, which are then averaged over a representative elementary volume. The so obtained transport equations at the macroscopic scale are thoroughly examined and each term is interpreted. Furthermore, it is shown that the tortuosity-connectivity does not slow the average speed of the ionic species down. The transport equations in the representative elementary volume are then compared with the equations obtained in an equivalent pore. Lastly, comparing Darcy’s law and the Hagen-Poiseuille equation in a cylindrical equivalent pore, the tortuosity-connectivity parameter is obtained for four dierent concretes. The proposed model provides very good results when compared with the experimentally obtained chloride profiles for two additional concretes.

This study aims to understand Filipino rice farmers’ aspirations, both farming and non-farming-related. Understanding aspirations can help the government and interested third-party entities to provide impactful initiatives to farmers. The Role Identity Theory guided our analysis in this study. This study is predominantly qualitative, with focus group discussion as the main method of collecting data. The research sites were in Kalinga, Nueva Ecija, Laguna, Quezon, Northern Samar, Zamboanga del Sur, Sultan Kudarat, and Agusan del Norte. Among the farming-related aspirations noted in this study relate to property, fair price, infrastructure, government support, and good governance. The non-farming related aspirations relate to infrastructure development; progress; government support and governance; love, passion, peace, and unity; wellness and long life.

Fatty Acid Amide Hydrolase (FAAH) is one of the enzymes responsible of endocannabinoids metabolism. The inhibition of FAAH is a useful and indirect strategy to raise endogenous cannabinoid concentrations, which would be useful for the treatment of various pathological processes in which cannabinoid concentrations are lowered. In the present work, we present an extensive 3D-QSAR/CoMSIA study on a series of 90 irreversible inhibitors of FAAH of pyrimidinyl-piperazine-carboxamide structure. The final model obtained was extensively validated (q2 = 0.734; r2test = 0.966; r2m = 0.723), and based on the information derived from the contour maps we reported a series of 10 new compounds designed as powerful FAAH inhibitors (pIC50 of the best-proposed compounds = 12.196; 12.416).

Plant viral nanoparticles (VNPs) are attractive to researchers in nanomedicine due to their safety, easy production, resistance, and straightforward functionalization. In this paper, we developed and successfully purified a VNP derived from turnip mosaic virus (TuMV), a well-known plant pathogen, that exhibits high affinity for immunoglobulins G (IgG) thanks to its functionalization with the Z domain from staphylococcal protein A via gene fusion. We selected cetuximab as a model IgG to prove the versatility of this novel TuMV VNP by developing a fluorescent nanoplatform to mark tumoral cells of the line Cal33, from tongue squamous cell carcinoma. We observed that the fluorescent VNP-cetuximab bound selectively to Cal33 and were internalized by confocal microscopy, revealing the potential of this nanotool in cancer research.

This study introduces a Fiber Specklegram Sensor (FSS) design for temperature measurement utilizing a single-multi-single mode optical fiber configuration. FSS technology offers unique advantages for potential development into portable sensing systems. This investigation explores an FSS design compatible with miniaturization by optimizing the interrogation system based on the relationship between speckle grain size and filtering fiber area. Temperature variations are detected through fluctuations in optical power at the sensor output, offering a simple and reduced interrogation scheme. The performance of the FSS is assessed through post-calibration measurements compared to a commercial Fiber Bragg Grating (FBG) sensor, demonstrating comparable results. These findings pave the way for compact and portable fiber optic temperature sensing systems leveraging FSS advantages while maintaining compatibility with established fiber optic measurements.

Children with Autism Spectrum Disorder have deficits in social interaction and expressing and understanding emotions. Many robots for children with ASD have been proposed. However, few studies were found about how to design a social robot for children with ASD. Studies reviewed employed non-experimental studies to evaluate a social robot, but the methodology to design a social robot is rare. This study proposes a design path for a social robot for emotional communi-cation for children with ASD, following User-Centered Design approach. This design path is ap-plied with a study case, evaluated with an expert group on psychologist, human-robot interaction, human-computer interaction, and parents of children with ASD. Results show than following the design path proposed to design a social robot to communication emotions for children ASD is favorable.

The reinforcement of concrete by using polyolefin fibres may be considered in structural design to meet the requirements of the applicable code rules. In order to achieve a reliable use of such a composite material, use of full-scale real structures is needed. The conversion of lab testing data into real practice properties is challenging and significantly influenced by various aspects, among which the size effect is a key one. Given that the available literature does not report coinciding conclusions about such an effect on quasi-brittle materials reinforced with fibres, further research is justified. Therefore, this work studies the behaviour of notched beams with three proportional sizes by using self-compacting polyolefin reinforced concrete with a fibre volume fraction of 1.1%. Flexural testing was carried out according to the standard EN-14651, with the results revealing the existence of the size effect. In addition, a reduction of the residual strength identified in the larger specimens was observed in fracture surfaces with equal fibre content.

The use of polyolefin fibre reinforced concrete (PFRC) as an alternative for reducing or even eliminating the reinforcing steel bars employed in reinforced concrete has become real in the past years. This contribution analyses the improvements in sustainability that a change in the aforementioned reinforcement configuration might provide in a flyover bridge. Economic, environmental and social parameters of both possibilities were studied by means of the integrated value model for sustainable assessment use (Modelo Integrado de Valor para una Evaluación Sostenible, MIVES) used in Spain, which is a multi-criteria decision-making method based on the value function concept and the seminars delivered by experts. The results of the MIVES method showed that the use of PFRC in combination with reinforced concrete (RC) has a sustainability index 22% higher. An analysis of the parameters that form this evaluation shows that there are no remarkable differences in the financial costs between the two possibilities studied. Nevertheless, social and environmental aspects provide with a better qualification the option of building a bridge by using PFRC combined with RC.

Introduction: Infections associated with medical implants pose significant challenges to healthcare, demanding the development of new effective antimicrobial strategies. This study focuses on the creation of a novel biological membrane with enhanced antimicrobial properties by with the incorporation of either vancomycin or silver nanoparticles. Methods: Pericardium samples were impregnated with either silver nanoparticles (AgNPs) or vancomycin (VAN). The antimicrobial activity of the membranes was assessed through qualitative microbiological analysis, biofilm production and animal in vivo model of infection. Histological analysis was performed on the pericardium samples, and quantitative microbiological analysis was conducted on the tissue from the animal model and biocompatibility evaluation. Statistical analyses were carried out using appropriate tests. Results: Microbiological tests confirmed both VAN and AgNP showed inhibition halos against bacteria. Histological analysis indicated minimal inflammatory response and bacterial presence in VAN and AgNP groups compared to the control group revealed reduced bacterial presence. Biomechanical testing showed that polypropylene had the lowest tensile strength, while AgNP-impregnated pericardium exhibited lower resistance than VAN-impregnated and control pericardium. Conclusion: Lyophilized and decellularized bovine pericardium as a substrate, combined with the incorporation of vancomycin or silver nanoparticles, provides a versatile platform for combating infections associated with medical implants.

The latest World Atlas of Desertification represents a turning point in the diagnosis of desertification. While it forgoes desertification mapping due to the intrinsic complexity of the phenomenon and the impossibility of measuring it using a single indicator, it introduces the Convergence of Evidence paradigm, which identifies socioeconomic and biophysical variables whose behavior allows pointing out those areas prone to desertification. The Spanish National Action Program Against Desertification (PAND), back to 2008, already implemented a similar approach to identify five “desertification landscapes” within Spain using both socio-economic and climatic information. The PAND was not only pioneering but also, unfortunately, accurate. Desertification in Spain has continued to worsen and the first two decades of the 21st century have consolidated an agri-food model whose dynamics have exacerbated the desertification processes identified in the PAND. Despite its scientific value, the PAND lacked a proper action plan and was completely detached from the diagnosis. As a result the diagnosis it provided was not followed by effective actions to halt desertification in Spain. The Spanish Government's recent declaration of climate and environmental emergency requires a new strategy to combat desertification. This commitment is an excellent opportunity to update the diagnosis of the situation and, more crucially, to unify the different desertification sectoral policies and actions under a single front. We provide here elements for a roadmap to be designed around the pressures, impacts, and drivers that define today's Spanish desertification landscapes to manage them effectively and avoid their further degradation.

Increased exposure to artificial light at night can affect human health including disruption of melatonin production and circadian rhythms and extend to increased risks of hormonal cancers and other serious diseases. In addition, multiple negative impacts on fauna and flora are well documented, and it is a matter of fact that artificial light at night is a nuisance for ground-based astronomy. These impacts are frequently linked to the colour of the light or more specifically to its spectral content. Artificial light at night is often mapped by using space borne sensors, but most of them are panchromatic and thus insensitive to the colour. In this paper, we suggest a method that allows high resolution mapping of the Artificial light at night by using ground-based measurements with the LANcube system. The device separates the light detected in four bands (Red, Green, Blue, and Clear) and provides this information for six faces of a cube. We found relationships between the LANcube’s colour ratios and 1- the Melatonin Suppression Index, 2- the StarLight Index and 3- the Induced Photosynthesis Index. We show how such relationships combined with data acquisition from a LANcube positioned on the top of a car can be used to produce spectral indices maps of a whole city in a few hours.

Parallel manipulators with multiple end-effectors bring us interesting advantages over conventional parallel manipulators such as improved manipulability, workspace and avoidance of singularities. In this work the kinematics of a five-bar planar parallel manipulator equipped with two end-effectors is approached by means of the theory of screws. As an intermediate step the displacement analysis of the robot is also investigated. The input-output equations of velocity and acceleration are systematically obtained by resorting to reciprocal-screw theory. In that regard the Klein form of the Lie algebra se(3) of the Euclidean group SE(3) plays a central role. In order to exemplify the method of kinematic analysis, a case study is included. Furthermore, the numerical results obtained by means of the theory of screws are confirmed with the aid of special software like ADAMS.^TM

The high level of dengue virus (DENV) seroprevalence in areas where Zika virus (ZIKV) is circulating and the cross-reactivity between these two viruses have raised concerns on the risk of increased ZIKV disease severity for patients with a history of previous DENV infection. To determine the role of DENV pre-immunity in ZIKV infection, we analysed the T and B cell responses against ZIKV in donors with or without previous DENV infection. Using PBMCs from donors living in an endemic area in Colombia, we have identified, by interferon (IFN)-γ enzyme-linked immunospot (ELISPOT) assay, most of the immunodominant ZIKV T-cell epitopes in the non-structural proteins NS1, NS3 and NS5. Analyses of the T and B-cell responses in the same donors revealed a stronger T-cell response against peptides conserved between DENV and ZIKV, with a higher level of ZIKV-neutralizing antibodies in DENV-immune donors, in comparison with DENV-naïve donors. Strikingly, the potential for antibody mediated enhancement of ZIKV infection was reduced in donors with sequential DENV and ZIKV infection in comparison with donors with DENV infection only. Altogether, these data suggest that individuals with DENV immunity present improved immune responses against ZIKV.

Plastics have become an important environmental concern due to their durability and resistance to degradation. Out of all plastic materials, polyesters such as polyethylene terephthalate (PET) are amenable to biological degradation due to the action of microbial polyester hydrolases. The hydrolysis products obtained from PET can thereby be used for the synthesis of novel PET as well as becoming a potential carbon source for microorganisms. In addition, microorganisms and biomass can be used for the synthesis of the constituent monomers of PET from renewable sources. The combination of both biodegradation and biosynthesis would enable a completely circular bio-PET economy beyond the conventional recycling processes. Circular strategies like this could contribute to significantly decrease the environmental impact of our dependence on this polymer. Here we review the efforts made towards turning PET into a viable feedstock for microbial transformations. We highlight current bottlenecks in the degradation of the polymer and the metabolism of the monomers and we showcase fully biological or semisynthetic processes leading to the synthesis of PET from sustainable substrates.

Key performance indicators are essential for any company to enhance its competitiveness. How-ever, a common issue is the manual collection of production data using record sheets, which are later digitized on desktop computers and processed in Excel sheets. Shockingly, 41% of companies in Mexico have no plans for digitalization. This work aims to develop a Real-time Productivity Indicator Monitoring System using Industry 4.0 technologies for a medium-sized manufacturing firm specializing in die-cutting automotive parts. The Advanced Quality Planning methodology was applied to develop the Conceptual, Product, and Process Engineering and its validation. The experimental tests demonstrated a reliability level of 99.98%, which exceeded initial expectations. The primary contributions presented in this work are related to the development of algorithms, communication protocols, data analysis, and general optimization of the calculation process. The study's only limitation was the short experimentation time.

The functionalization of polymeric substances is of great interest for the development of innovative materials for advanced applications. For many decades, the functionalization of chitosan has been a convenient way to improve its properties with the aim to prepare new materials with specialized characteristics. In the present article, we summarize the latest methods for the modification and derivatization of chitin and chitosan, trying to introduce specific functional groups under experimental conditions, which allow a control over the macromolecular architecture. This is motivated because an understanding of the interdependence between chemical structure and properties is an important condition for proposing innovative materials. New advances in methods and strategies of functionalization such as click chemistry approach, grafting onto copolymerization, coupling with cyclodextrins and reactions in ionic liquids are discussed.

The aim of this work is to provide a full description of how air temperature and solar radiation induce changes in the land cover over an Antarctic site. We use shortwave broadband albedo (albedo integrated in the range 300-3000 nm) from a spaceborne sensor and from field surveys to calculate the monthly relative abundance of landscape units. Field albedo data were collected using a portable albedometer over seven landscape units: clean fresh snow; clean old snow; rugged landscape composed of dirty snow with disperse pyroclasts and rocky outcrops; dirty snow; stripes of bare soil and snow; shallow snow with small bare soil patches; bare soil. MODIS MCD43A3 daily albedo product was downloaded using the Google Earth Engine API from the 2000-2001 season to the 2020-2021 season. Each landscape unit was characterized by an albedo normal distribution. The monthly relative abundance of the landscape units were calculated by fitting a linear combination of the normal distributions to the histogram of the MODIS monthly mean albedo. The monthly relative abundance of the landscape unit consisting of rugged landscape composed of dirty snow, with dispersed clasts and small rocky outcrops exhibits a high linear positive correlation with the monthly mean albedo (R2=0.87) and a high linear negative correlation with the monthly mean air temperature (R2= 0.69). The increase of the solar radiation energy flux from September to December coincides with the decrease of the relative abundance of the landscape unit composed of dirty snow with dispersed clasts and small rocky outcrops. We propose a mechanism to describe the evolution of the landscape: uncovered pyroclasts act as melting centres favouring the melting of surrounding snow. Ash does not play a decisive role in the melting of the snow. The results also explain the observed decreasing of the thaw depth of the permafrost on the island in the period 2006-2014, resulting from an increase in the snow cover over the whole island.

This study explores the potential of using a Siamese Network as a biomarker for assessing the effectiveness of Dolphin-Assisted Therapy (DAT) in children with Cerebral Palsy (CP). The problem statement revolves around the need for objective measures to evaluate the impact of DAT on patients with CP, considering the subjective nature of traditional assessment methods. The methodology involves training a Siamese network, a type of neural network designed to compare similarities between inputs, using data collected from CP patients undergoing DAT sessions. The network is trained to learn patterns and similarities between pre- and post-therapy evaluations, in order to identify biomarkers indicative of therapy effectiveness. Notably, the Siamese Network’s architecture ensures that comparisons are made within the same feature space, allowing for more accurate assessments. The results of the study demonstrate promising findings, indicating different patterns in the output of the Siamese Network that correlate with improvements in symptoms of CP post-DAT. These findings suggest the potential utility of the Siamese Network as a biomarker to monitor therapy outcomes in children with CP who undergo DAT, offering a more objective and quantifiable approach to assessing therapeutic interventions. Significant disparities in neuronal voltage perturbations, with a mean of 7.9825 dB in specific samples compared to 6.2838 dB in the data set, indicate a marked difference from resting activity. This suggests that dolphin-assisted therapy selectively activates specific brain regions uniquely during the intervention.

Background: The COVID-19 pandemic has promoted a shortage of filtering facepiece respirators (FFRs) and the emergence of new FFRs brands. We aimed to determine the fit provided by in-use FFRs in Peruvian healthcare workers (HCWs) during the COVID-19 pandemic. Methods: We enrolled 279 HCWs from 37 primary healthcare centers with highest burden of care for TB in Peru, of which 263 were assessed using quantitative fit tests (QNFT). Results were expressed as real-time fit factor (rt-FF) and overall fit factor (overall-FF), which was categorized as ≥100 (optimal result), 50-99, and <50. Results: We identified 3M 1860 FFRs (33.1%), Xiantao Zhong Yi ZYB-11 FFRs (24.7%) and Makrite 9500 FFRs (20.5%), mainly. Eighty-seven HCWs (33.1%) had an optimal overall-FF, 27 (10.3%) between 50-99, and 149 (56.7%) less than 50. Of the 87 HCWs with optimal over-all-FF, 73 (83.9%) were 3M 1860 FFR. Of the 27 participants with overall-FF between 50-99, 7 (25.9%) were Makrite 9500, while of the 149 with overall-FF less than 50, 58 (38.9%), and 47 (31.5%) were Xiantao Zhong Yi ZYB-11 and Makrite 9500, respectively. Conclusion: The Xiantao Zhong Yi and Makrite FFRs do not adapt adequately to the face of Peruvian HCWs, most having fit factors less than 50.

Height assignment is an important problem for satellite measurements of Atmospheric Motion Vectors (AMVs) that are interpreted as winds by forecast and assimilation systems. Stereo methods assign heights to AMVs from the parallax observed between observations from different vantage points in orbit while tracking cloud or moisture features. In this paper, we fully develop the stereo method to jointly retrieve wind vectors with their geometric heights from geostationary satellite pairs. Synchronization of observations between observing systems is not required. NASA and NOAA stereo-winds codes have implemented this method and we have processed large datasets from GOES-16, -17, and Himawari-8. Our retrievals are validated against rawinsonde observations and demonstrate the potential to improve forecast skill. Stereo winds also offer an important mitigation for the loop heat pipe anomaly on GOES-17 during times when warm focal plane temperatures cause infra-red channels that are needed for operational height assignments to fail. We also examine several application areas, including deep convection in tropical cyclones, planetary boundary layer dynamics, and fire smoke plumes, where stereo methods provide insights into atmospheric processes. The stereo method is broadly applicable across the geostationary ring where systems offering similar Image Navigation and Registration (INR) performance as GOES-R are deployed.

A synoptic compendium of the legumes of the Mimosoideae clade in northeastern Mexico is presented for the first time, including changes in their botanical nomenclature and retypification of genera. Furthermore, based on new information recently published, the taxonomic limits of several new genera segregated from Acacia (Acaciella, Mariosousa, Senegalia and Vachellia) and Prosopis (Neltuma and Strombocarpa) are clarified and included. Based on field work, collecting botanical samples during the last 30 years, a review of botanical materials and database in national and international, we have completed the diversity of legumes of the Mimosoideae clade of northeastern Mexico. Three tribes (Acacieae, Ingeae and Mimosaeae), 22 genera and 92 species, and 19 infraspecif categories were recorded. Only the genus Painteria is endemic to Mexico. Eighty-eight species are native to Mexico, and four are exotic, Acacia salicina, Neptunia prostrata, Neltuma chilensis and Albizia lebbeck. Twenty-eight species are endemic to Mexico, nine species are endemic of northeastern Mexico, and four species endemic to only one state in Mexico. The 22 registered genera represent 44% and 65% of the generic flora of the Mimosoideae clade for Mexico and the planet respectively while the 92 species registered represent 3% and 18% of the species of the Clade Mimosoideae for the planet and Mexico respectively. According to the new nomenclature of legumes, the number of genera in the Mimosoideae clade in northern Mexico has been increased from 19 to 24.

Taste disorders are common among cancer patients undergoing chemotherapy, with a prevalence ranging from 20% to 86%, persisting throughout treatment. This condition leads to reduced food consumption, increasing the risk of malnutrition. Malnutrition is associated not only with worse treatment efficacy and poor disease prognosis but also with reduced functional status and quality of life. The fruit of Synsepalum dulcificum (Daniell), commonly known as miracle berry or miracle fruit, contains miraculin, a taste-modifying protein with profound effects on taste perception. The CLINMIR Protocol is a triple-blind, randomized, placebo-controlled clinical trial designed to evaluate the regular consumption of a food supplement containing a miraculin-based novel food, dried miracle berry (DMB), on the taste perception (measured through electrogustometry) and nutritional status (evaluated through the GLIM Criteria) of malnourished cancer patients under active antineoplastic treatment. To this end, a pilot study was designed with 30 randomized patients divided into three study arms (150 mg DMB + 150 mg freeze-dried strawberries, 300 mg DMB or placebo) for three months. Throughout the five main visits, an exhaustive assessment of different affected parameters susceptible to improvement through regular consumption of the miraculin-based food supplement will be conducted, including electrical and chemical taste perception, smell perception, nutritional and morphofunctional assessment, diet, quality of life, fatty acid profile of erythrocytes, levels of inflammatory and cancer-associated cytokines, oxidative stress, antioxidant defense system, plasma metabolomics, and saliva and stool microbiota. The primary anticipated result is that malnourished cancer patients with taste distortion who consume the miraculin-based food supplement will report an improvement in food taste perception. This improvement translates into increased food intake, thereby ameliorating their nutritional status and mitigating associated risks. Additionally, the study aims to pinpoint the optimal dosage that provides maximal benefits. The protocol adheres to the SPIRIT 2013 Statement, which provides evidence-based recommendations and is widely endorsed as an international standard for trial protocols (https://www.spirit-statement.org/spirit-statement/). The clinical trial protocol has been registered at http://clinicaltrials.gov (NCT05486260).

Cryopreservation is a stressful process for sperm as it is associated with an increased production of reactive oxygen species (ROS). Elevated ROS levels, which create an imbalance with antioxidant capacity, may result in membrane lipid peroxidation (LPO), protein damage and DNA fragmentation. This study aimed to determine whether membrane LPO and DNA fragmentation of frozen-thawed horse sperm relies upon the antioxidant activity, including enzymes (superoxide dismutase (SOD), glutathione peroxidase (GPX), catalase (CAT), and paraoxonase type 1 (PON1)); non-enzymatic antioxidant capacity (Trolox equivalent antioxidant capacity (TEAC), plasma ferric reducing antioxidant capacity (FRAP), and cupric reducing antioxidant capacity (CUPRAC)); and the oxidative stress index (OSI), of their seminal plasma (SP). Based on total motility and plasma membrane integrity (SYBR14+/PI−) after thawing, ejaculates were hierarchically (p &lt; 0.001) clustered into two groups of good (GFE) and poor (PFE) freezability. LPO and DNA fragmentation (global DNA breaks) were higher (p &lt; 0.05) in PFE than in GFE, with LPO and DNA fragmentation (global DNA breaks) after thawing showing a positive relationship (p &lt; 0.05) with SP-OSI levels and ROS production. In addition, sperm motility and membrane integrity after thawing were negatively (p &lt; 0.05) correlated with the activity levels of SP antioxidants (PON1 and TEAC). The present results indicate that LPO and DNA fragmentation in frozen-thawed horse sperm vary between ejaculates. These differences could result from variations in the activity of antioxidants (PON1 and TEAC) and the balance between the oxidant and antioxidant components present in the SP.

The search for a continuous continental record of interglacial periods in semi-arid regions is problematic due to the absence of stable and continuous sedimentary systems over time in this type of climate. In this work, a relatively stable basin is described and analyzed during the last interglacial in a semi-arid region of the western Mediterranean. For this purpose a geomorphological, stratigraphic and sedimentological study has been carried out, with dating through 230Th. A semi-endorrheic Pleistocene basin has been identified, with two units that correspond to a fluvial-lacustrine system (unit P1) and an alluvial system (unit P2). Unit P1 has been dated in the MIS 5e interglacial episode. A framework is described in which the Aljezares Quaternary basin can be considered as a possible source of paleoenvironmental and paleoclimatic information in semi-arid regions from the last interglacial period in future studies.

Background: Visual acuity (VA) assessments are crucial in ophthalmology but traditionally rely on in-clinic evaluations. The emergence of telemedicine has spurred interest in creating dependable self-administered VA tests for use beyond standard clinical environments. This study evaluates the practicality and validity of a self-administered Near VA card test against traditional Snellen and Rosenbaum Pocket Vision Screener (RPVS) methods for home monitoring and enhancing clinical workflow. Methods: In a cross-sectional study a near VA card (Hadassah Self-Visual Acuity Screener-HSVA) was developed with written and videotaped instructions for self-use. Patients with a minimal best corrected VA (BCVA) of 1.0 LogMAR in at least one eye were recruited from Ophthalmology and Optometry clinics. Outcomes included mean BCVA difference between the self-administered and those obtained by the examiner, and correlations among BCVA values obtained by Snellen, RPVS, HSVA and previous distance BCVA according to the patient electronic medical records. Results: A total of 275 participants (mean age: 42.5±19.4 years, range: 18-89 years, 47% female) were included. Test-retest reliability analysis for the HSVA demonstrated very good correlation and repeatability (n=38 patients.; Rs=1.0, P