A super-porous hybrid platform can offer significantly increased number of reaction sites for the analytes and thus can offer advantages in the biosensor applications. In this work, a significantly improved sensitivity and selectivity of hydrogen peroxide (H2O2) cancer sensor is demonstrated by a super-porous hybrid CuO/Pt NP platform. The super-porous hybrid platform is fabricated by a physiochemical approach combining the physical vapor deposition of Pt NPs and electrochemical deposition of super-porous CuO structures by adopting a dynamic hydrogen bubble technique. Under an optimized condition, the hybrid CuO/Pt biosensor demonstrates a very high sensitivity of 2,205 µA/mM∙cm2 and a low limit of detection (LOD) of 140 nM with a wide range of H2O2 detection. This is meaningfully improved performance as compared to the CuO-based H2O2 sensors as well as to the previously reported metal oxide based H2O2 sensors. The hybrid CuO/Pt platform exhibits excellent selectivity against other interfering molecules such as glucose, fructose, dopamine, and ascorbic acid. Due to the synergetic effect of highly porous CuO structures and underlying Pt NPs, the CuO/Pt architecture offers extremely abundant active sites for the H2O2 reduction and electron transfer pathways.

Hf1-xZrxO2 (HZO) thin films are versatile materials suitable for advanced ferroelectric semiconductor devices. Previous studies have shown that the ferroelectricity of HZO thin films, can be stabilized by doping them with group III elements at low concentrations. While doping with Y improves the ferroelectric properties, there has been limited research on Y-HZO thin films fabricated using atomic layer deposition (ALD). In this study, we investigated the effects of Y doping cycles on the ferroelectric and electrical properties of as-deposited Y-HZO thin films with vaying compositions fabricated through ALD. The Y-HZO thin films were stably crystallized without the need for post-thermal treatment and exhibited transition behavior depending on the Y-doping cycle and initial composition ratio of the HZO thin films. These Y-HZO thin films offer several advantages, including enhanced dielectric constant, leakage current density, and improved endurance. Moreover, the optimized Y-doping cycle induced a phase transformation that resulted in Y-HZO thin films with improved ferroelectric properties, exhibiting stable behavior without fatigue for up to 1010 cycles. These as-deposited Y-HZO thin films show promise for applications in semiconductor devices that require high ferroelectric properties, excellent electrical properties, and reliable performance with a low thermal budget.

(1) Background: This study, drawing from the theoretical framework of the Theory of Planned Behavior (TPB), examines the structural relationship among attitudes, subjective norms, perceived behavioral control (PBC), and behavioral intention. The study focuses on investigating how the perceived risk associated with particulate matter moderates the relationships between 'attitudes and behavioral intention,' 'subjective norms and behavioral intention,' and 'PBC and behavioral intention' within the context of individuals engaged in outdoor sports; (2) Methods: The data were collected from outdoor sports gatherings facilitated through a popular South Korean sports meetup application. Confirmatory factor analysis was employed to establish the construct validity of the measurement scale, assess factor loadings, averaged variance extracted (AVE), and construct reliability (CR). We also ensured the reliability of the measurement scale through Cronbach's α analysis. To achieve our research objectives, we utilized structural equation modeling with maximum likelihood estimation to examine the positive relationships under investigation. Additionally, we performed moderation analysis using the statistical software Jamovi.; (3) Results: The findings demonstrate the significant impacts of attitudes, subjective norms, and PBC on behavioral intention and reveal that perceived risk acts as a moderator, influencing the relationship between PBC and behavioral intention.; (4) Conclusions: Therefore, the government will need to exert substantial efforts to mitigate particulate matter levels.

A high-voltage transmission tower consists of structures to avoid the risk of electric shock and to prevent the risk of collapse. Hence, towers are generally designed to be high-rise for efficiency. The main posts of the tower are primary structural members that resist loads under various load conditions. Therefore, the contribution of the secondary member to securing the stiffness and strength of the main posts by reducing the effective buckling length is important. However, there are no detailed design criteria for secondary members. In this study, the structural effects of horizontal members and braces on the torsional stiffness, elastic buckling strength, and load-carrying capacity of transmission towers were observed through various structural analysis methods including linear-elastic, eigenvalue, and geometric nonlinear and inelastic analyses under governing load combinations. According to the analytical study, rather than the horizontal members, the brace spacing significantly affects the structural performance. Therefore, the number of horizontal members can be minimized if sufficient brace members are erected. If the brace spacing is wide, it is recommended that the horizontal members be erected to create K bracing, and the buckling resistance of the main posts can be thus enhanced.

Graphene materials synthesized using direct laser writing (laser-induced graphene; LIG) are fa-vorable sensor materials because of their large surface area, ease of fabrication, and cost effec-tiveness. In particular, LIG decorated with metal nanoparticles (NPs) has been used in various sensors, including chemical sensors and electronic and electrochemical biosensors. However, the effect of metal decoration on LIG sensors remains controversial; hypotheses based on computa-tional simulations do not always match experimental results, and even experimental results re-ported by different researchers have not been consistent. In the present study, we explored the effects of metal decorations on LIG gas sensors, with NO2 and NH3 gases as representative oxi-dizing and reducing agents, respectively. To eliminate unwanted side effects arising from metal salt residues, metal NPs were directly deposited by vacuum evaporation. Although the gas sen-sitivities of the sensors deteriorate upon metal decoration irrespective of the metal work function in the case of NO2 gas, they improve upon metal decoration in the case of NH3 exposure. A careful investigation of the chemical structure and morphology of the metal NPs in the LIG sensors shows that the spontaneous oxidation of metal NPs with a low work function changes the be-havior of the LIG gas sensors and that the sensor behaviors under NO2 and NH3 gases follow different principles.

This paper proposes a metaphysical framework for distinguishing between human and machine intelligence. By drawing an analogy from Kant’s incongruent counterparts, it posits two identical deterministic worlds -- one comprising a human agent and the other comprising a machine agent. These agents exhibit different types of information processing mechanisms despite their apparent sameness in a causal sense. By postulating the distinctiveness of human over machine intelligence, this paper resolves what it refers to as “the vantage point problem” – namely, how to legitimize a determinist’s assertion of determinism by placing the determinist within the universe.

We find that the overnight returns of Korean exchange-traded index funds (ETFs) are significantly positive, whereas the subsequent intraday returns are negative. These intraday return reversals are caused by relatively higher opening prices than the closing prices. In the Korean ETF market, where institutional investors are dominant participants, the return reversals are not explained by the attention hypothesis as in Berkman et al. [1]. Hence, we investigate whether the disagreement hypothesis can explain return reversals. Under the disagreement situations between positive and negative traders at the open, positive traders can have a positive influence on the ETF prices by increasing their investments. However, negative traders, who give up investments due to limited short selling opportunities in the ETF market, have no effects on the prices. Comparing ETF markets with KOSPI 200 Futures where there are no restrictions on short selling, we find that short selling constraints are significant factors for the return reversals. This implies that disagreement among the investors can cause return reversals even in the markets without noise traders. Using unique Korean market data, we conclude that return reversals cannot be completely explained by the attention hypothesis, and that disagreement among investors is also a significant factor for the return reversals. This study contributes to the existing literature by showing that the attention hypothesis does not explain return reversals in the ETF market completely, and suggesting the disagreement hypothesis as an alternative.

Radiator reliability is crucial in environments characterized by high temperatures and friction, where prompt interventions are often required to prevent system failures. This study introduces a proactive approach to radiator fault diagnosis, leveraging the integration of Gaussian Mixture Model (GMM) and Long-Short Term Memory (LSTM) autoencoders. Vibration signals from radiators were systematically collected through randomized durability vibration bench tests, resulting in four operating states—two normal, one unknown, and one faulty. Time-domain statistical features of these signals were extracted and subjected to Principal Component Analysis (PCA) to facilitate efficient data interpretation. Subsequently, this study discusses the comparative effectiveness of GMM and LSTM in fault detection. GMMs are deployed for initial fault classification, leveraging their clustering capabilities, while LSTM autoencoders excel in capturing time-dependent sequences, facilitating advanced anomaly detection for previously unencountered faults. This alignment offers a potent and adaptable solution for radiator fault diagnosis, particularly in challenging high-temperature or high-friction environments. Consequently, the proposed methodology not only provides a robust framework for early-stage fault diagnosis but also effectively balances diagnostic capabilities during operation. Additionally, this study presents the foundation for advancing reliability life assessment in accelerated life testing, achieved through dynamic threshold adjustments using both the absolute log-likelihood distribution of the GMM and the reconstruction error distribution of the LSTM autoencoder model.

This study examined ways to prevent failures in the front-end of forklifts by addressing the center of gravity of heavy objects carried by forklifts, predicting the remaining useful lifetime (RUL), and the fault diagnosis based on alarm rules. In the research process, acceleration signals were acquired from the outer beam of the front-end of the forklift. A one-second window was applied to extract the time-domain statistical features, which were then set as variables. An exponentially weighted moving average was used to smooth the noise in the feature data set. The AWGN and LSTM autoencoders were used for data augmentation. Based on them, random forest and lightGBM models were used to develop classification models for the weight center of heavy objects carried by a forklift. In addition, contextual diagnosis performed by applying exponentially weighted moving averages to the classification probabilities of the machine learning models showed that random forest achieved an accuracy of 0.9563 and lightGBM achieved an accuracy of 0.9566. In addition, the acceleration data were collected through experiments to predict forklift failure and RUL because of the repeated forklift use when the center of heavy objects carried by the forklift was skewed to the right. The time-domain statistical features of the acceleration signals were extracted and set as variables by applying a 20-second window. Subsequently, logistic regression and random forest models were used to classify the failure stages of the forklifts. The f1-score (macro) obtained were 0.9790 and 0.9220 for logistic regression and random forest, respectively. In addition, the random forest probabilities for each stage were combined and averaged to generate a degradation curve and derive the failure threshold. The coefficient of the exponential function was calculated using the least squares method on the degradation curve, and the RUL prediction model was developed to predict the failure point. In addition, the SHAP algorithm was used to identify the significant features in classifying the stage. The alarm rule-based fault diagnosis was performed using the threshold of the normal stage distribution of the significant features.

Ultraviolet (UV) radiation has both harmful and beneficial effects on human health. It can cause skin damage and cancer, but also provides the primary source of vitamin D. Additionally, UV radiation affects energy metabolism in mice with metabolic diseases and has protective effects on hypertension and cardiovascular diseases.Metabolic Syndrome is a collection of metabolic dysfunctions such as dyslipidemia, hypertension, hyperglycemia, abdominal/central obesity, and insulin resistance. Chronic UVR exposure suppressed obesity and type 2 diabetes in high-fat diet-fed mice, while vitamin D supplementation did not replicate these effects. On the other hand, topical application of nitric oxide (NO) donors replicated UV effects on mice, and NO scavengers prevented the positive impact of UV. UVR may prevent the development of obesity and metabolic syndrome through mechanisms that depend on UVR-induced NO, not vitamin D. Exposure to sunshine has a protective impact on blood pressure and cardiovascular disease. Although lower vitamin D concentration is linked to increased hypertension and the incidence of CVD, oral vitamin D supplementation does not decrease blood pressure or the risk of CVD, indicating that vitamin D may not mediate the beneficial effects of sun exposure. Instead, NO plays a crucial role as an endogenous vasodilator, produced by the vascular endothelium. Solar UVA may release nitrogen oxides from skin storage into the bloodstream, lowering blood pressure and cardiovascular mortality.In conclusion, UVR exposure could be a promising non-pharmacological intervention for metabolic syndrome, hypertension, and CVD prevention, and NO may play a crucial role in mediating these effects. Further research is needed to explore the precise mechanisms and identify the optimal doses and exposure times of UVR.

Rotorcrafts operate HUMS for fault diagnosis, but the capabilities of HUMS analysts are important due to the complex mechanical configuration of rotorcraft and the difficulty of analysis. Accordingly, an advanced algorithm is needed to identify faults, and flight data can be used to develop the algorithm. However, flight data contains abnormal or missing data due to problems such as sensor defects, which can be a major problem in algorithm development. Therefore, in this paper, we study a gap filling method using MLP to obtain normal data when there are problems such as abnormal or missing data in rotorcraft flight data. Existing methods typically fill the gap through interpolation or curve fitting using the before and after values of missing data. However, in this study, normal values were estimated using the values of other parameters at the moment of missing or abnormal data occurred. As a result of evaluating the performance of the trained MLP using normal data, it was confirmed that the output of the model well estimates the changing trend of the target. And when abnormal data was applied to the trained model, it was confirmed that point outliers were eliminated and appropriate values were found in the case of missing data.

Hepatocellular Carcinoma (HCC) continues to pose a substantial global health challenge due to its high incidence and limited therapeutic options. In recent years, the Janus Kinase (JAK) and Signal Transducer and Activator of Transcription (STAT) pathway has emerged as a critical signaling cascade in HCC pathogenesis. The review commences with an overview of the JAK/STAT pathway, delving into the dynamic interplay between the JAK/STAT pathway and its numerous upstream activators, such as cytokines and growth factors enriched in pathogenic livers afflicted with chronic inflammation and cirrhosis. This paper also elucidates how the persistent activation of JAK/STAT signaling leads to diverse oncogenic processes during hepatocarcinogenesis, including uncontrolled cell proliferation, evasion of apoptosis, and immune escape. In the context of therapeutic implications, this review summarizes recent advancements in targeting the JAK/STAT pathway for HCC treatment. Preclinical and clinical studies investigating inhibitors and modulators of JAK/STAT signaling are discussed, highlighting their potential in suppressing the deadly disease. The insights presented herein underscore the necessity for continued research into targeting the JAK/STAT signaling pathway as a promising avenue for HCC therapy.

A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.

Gastric cancer is the 5th most common disease in the world and the 4th most common cause of death. It is diagnosed through esophagogastroduodenoscopy with biopsy, however there are limitations in finding lesions in the early stages. Recently, research has been actively conducted to use liquid biopsy to diagnose various cancers, including gastric cancer. Various substances derived from cancer are reflected in the blood. By analyzing these substances, it was expected that not only the presence or absence of cancer but also the type of cancer can be diagnosed. However, the amount of these substances is extremely small, and even these have various variables depending on the characteristics of the individual or the characteristics of the cancer. To overcome these, we collected methylated DNA fragments using MeDIP and compared them with normal plasma to characterize gastric cancer tissue or patient’s plasma. And we attempted to diagnose gastric cancer using the characteristics of cancer reflected in the blood through the cancer tissue and patient’s plasma. As a result, we confirmed that the consistency of common methylated fragments between tissue and plasma was approximately 41.2%, and found the possibility of diagnosing and characterizing cancer using the characteristics of the fragments through SFR and 5'end-motif analysis.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

In this study, a motion control problem for the vessels towed by tugboats or towing ships on the sea is considered. The towed vessels including barge ships are need to have assistance of tugboats. Combining two vessels, some work purposes in the sea or harbor area can be completed. In this study, the authors give newly developed mathematical model and control system strategy. Especially, the system model fully presenting the physical characteristics of two vessels are derived. For controlling the system effectively, it is considered that the towed vessel has no power propulsion system but the rudder is activated to improve the maneuverability. Considering the strong nonlinearities included in the vessel dynamics, the modelled system is presented by nonlinear system without linearization of nonlinear parameters. Thus, the control system for the towed vessel is designed based on the nonlinear control scheme. Exactly, the back-stepping control method is applied to its motion control. Also, the PID control method is applied for comparing with the proposed control strategy.

The number of fishers working on commercial fishing vessels worldwide is approximately 159,800 according to the Food and Agriculture Organization of the United Nations. The International Labour Organization estimates that the mean annual number of deaths during fishing is approximately 24,000. Most guidelines for the prevention of marine accidents have been developed with a focus on vessels involved in international navigation. As these guidelines may have parts that are unsuitable for application in small-scale boats operating in coastal areas, appropriate modifications are required. This study analyzed quantitative data on 1,790 marine accidents that occurred in trap fishery, a globally common type of fishery, and data obtained through a survey of 101 fishers in South Korea. A guideline to reduce the rate of fatal accidents was developed using the Bayesian network, a method used for the analysis of accidents, as suggested in the formal safety assessment protocol. The results of data analysis and the developed guidelines are expected to be beneficial to all fishers involved in trap fishery across many countries worldwide.

Purpose: To evaluate clinical outcomes after bilateral mix-and-match cataract surgery using extended depth of focus (EDOF) and diffractive multifocal (DMF) intraocular lenses (IOLs). Methods: Thirty-seven patients received Tecnis Symfony EDOF IOL (ZXR00) implantation in the dominant eye, and Tecnis +3.25 DMF IOL (ZLB00) in the non-dominant eye. Patients were followed for 3 months, and uncorrected and corrected distance visual acuity (UDVA, CDVA) , uncorrected intermediate and near visual acuity (UIVA, UNVA), contrast sensitivity, defocus curves, stereopsis, and patient satisfaction were assessed. Results: At 3 months, mean logMAR UDVA was 0.07 ± 0.09 in EDOF IOL eyes, 0.12 ± 0.11 in DMF IOL eyes, and 0.02 ± 0.05 in both eyes. UIVA was 0.11 ± 0.11 in EDOF IOL eyes, 0.16 ± 0.12 in DMF IOL eyes, and 0.04 ± 0.07 in both eyes. UNVA was 0.25 ± 0.15 in EDOF IOL eyes, 0.22 ± 0.16 in DMF IOL eyes, and 0.13 ± 0.13 in both eyes. Thirty patients(81.1%) were more than satisfied with near vision, and 8 patients(21.6%) complained of severe glare and halo. Spectacle independence for near vision was achieved in 34 patients(91.9%), and 31 patients(83.8%) had better than a 50 second arc of stereopsis. Conclusion: Mix-and-match cataract surgery with EDOF and DMF IOL implantation provided good visual outcomes through all distances. Also excellent patient satisfaction was achieved with high level of spectacle independence and minimal photic phenomena.

Cisplatin induces early-onset ototoxicity, resulting in hearing loss. The exact mechanism by which cisplatin causes ototoxicity remains unclear. The purpose of this study was to identify the involvement of receptor-interacting protein kinase(RIP)3-dependent necroptosis in cisplatin-induced ototoxicity in animal models. Sprague–Dawley rats (SD, 8 week) were treated via intraperitoneal (i.p) injection with cisplatin (16 mg/kg for 1 day), and their hearing thresholds were was measured by the auditory brainstem response (ABR) method. Hematoxylin and eosin (H-E) staining, immunohistochemistry, and western blots were performed to determine the effect of cisplatin-induced ototoxicity on cochlear morphology. H-E stains outlined necroptotic changes in the organ of Cortis (OCs) and spiral ganglion neurons (SGNs). Additionally, immunohistochemistry and western blot analysis showed overexpression of RIP3 in the OCs and SGNs that were treated with cisplatin. These results suggest that RIP3-dependent necroptosis was substantial in cisplatin-induced ototoxicity; inner cochlear regions, the OCs, and SGNs were especially sensitive to necroptosis.

To expand the application scope and increase the demand for non-crimp fabrics (NCFs) as a lightweight vehicle material, the delamination and thermal strain in NCF composites must be restricted. Accordingly, to simultaneously improve the interfacial bonding and thermal stability of the NCF composites, in this study the epoxy resin, in which SiO2 nanoparticles was modified by a silane coupling agent, were infused to the stacked NCFs and between the layers of NCFs through the vacuum-assisted resin infusion molding (VARIM) process.

Cardiac hypertrophy is an adaptive response to various pathological insults including hypertension. However, sustained hypertrophy can cause impaired calcium regulation, cardiac dysfunction, and remodeling, accompanied by cardiac fibrosis. Our previous study identified miR-25 as a regulator of SERCA2a, and that inhibition of miR-25 improved cardiac function and reduced fibrosis by restoring SERCA2a expression in a murine heart failure model. However, the precise mechanism underlying the reduction of fibrosis by miR-25 inhibition remains unclear. Therefore, we postulate that miR-25 may have additional targets that contribute to regulating cardiac fibrosis. Using in silico analysis, Krüppel-like factor 4 (KLF4) was identified as an additional target of miR-25. Further experiments confirmed that KLF4 was directly targeted by miR-25 and that its expression was reduced by long-term treatment with Angiotensin II, a major hypertrophic inducer. Subsequently, treatment with a miR-25 inhibitor alleviated the cardiac dysfunction, fibrosis, and inflammation induced by Angiotensin II. These findings indicate that inhibiting miR-25 not only enhances calcium cycling and cardiac function via SERCA2a restoration but also reduces fibrosis by restoring KLF4 expression. Therefore, targeting miR-25 may be a promising therapeutic strategy for treating hypertensive heart diseases.

The accurate diagnosis and effective treatment of mental health disorders such as depression remain challenging owing to the complex underlying causes and varied symptomatology. Traditional information extraction methods struggle to adapt to evolving diagnostic criteria such as the Diagnostic and Statistical Manual of Mental Disorders fifth edition (DSM-5) and to contextualize rich patient data effectively. This study proposes a novel approach for enhancing information extraction from mental health data by integrating medical knowledge graphs and large language models (LLMs). Our method leverages the structured organization of knowledge graphs specifically designed for the rich domain of mental health combined with the powerful predictive capabilities and zero-shot learning abilities of LLMs. This research enhances the quality of knowledge graphs through entity linking and demonstrates superiority over traditional information extraction techniques, making a significant contribution to the field of mental health. It enables a more fine-grained analysis of the data and the development of new applications. Our approach redefines the manner in which mental health data are extracted and utilized. By integrating these insights with existing healthcare applications, the groundwork is laid for the development of real-time patient monitoring systems. The performance evaluation of this knowledge graph highlights its effectiveness and reliability, indicating significant advancements in automating medical data processing and depression management.

Background: Inflammasomes recognize cytosolic danger signals, including pathogens, and subsequently induce the secretion of pro-inflammatory cytokines, such as interleukin (IL)-1β. Studying inflammasomes in the red fox (Vulpes vulpes) is crucial from a wildlife veterinary and public health perspective, as it can be used to help control and prevent the transmission of zoonotic pathogens. The understanding of how diversity in inflammasomes across species affects pathogen carriage in the red fox is still limited. Methods: We investigated the activation and intracellular mechanisms of three inflammasomes (NLRP3, AIM2, and NLRC4) in fox peripheral blood mononuclear cells (PBMCs), using established triggers and inhibitors derived from humans and mice. Results: Fox PBMCs exhibited normal activation and induction of IL-1β secretion in response to representative inflammasome triggers (ATP and nigericin for NLRP3, dsDNA for AIM2, flagellin for NLRC4). However, in inhibitor studies, MCC950, a selective NLRP3 inhibitor, suppressed IL-1β secretion mediated by the fox AIM2 and NLRC4 inflammasomes. Conclusions: These findings suggest that NLRP3 may have a common role in dsDNA- and flagellin-mediated inflammasome activation in the red fox. In conclusion, this fox inflammasome biology can be applied to the control of zoonotic infections and the treatment of inflammasome-mediated diseases in the red fox.

We consider Pisot family substitution tilings in $\R^d$ whose dynamical spectrum is pure point. There are two cut-and-project schemes(CPS) which arise naturally: one from the Pisot family property and the other from the pure point spectrum respectively. The first CPS has an internal space $\R^m$ for some integer $m \in \N$ defined from the Pisot family property, and the second CPS has an internal space $H$ which is an abstract space defined from the property of the pure point spectrum. However it is not known how these two CPS's are related. Here we provide a sufficient condition to make a connection between the two CPS's. In the case of Pisot unimodular substitution tiling in $\R$, the two CPS's turn out to be same due to [5, Remark 18.5].

During the recent decades, global warming by greenhouse gas evolution has attracted worldwide attention and evermore strict regulations thereon have become institutionalized as international policies. In the process, more environment-friendly power generation technologies have been developed utilizing fossil fuels with a view to timely commercialization. As one of such “clean coal” technology, Integrated Gasification Fuel Cell system is a promising power generation means and COS hydrolysis reactor is installed downstream of coal syngas to remove acidic gas constituents such as H2S and COS. The most significant design parameters affecting performance of the COS hydrolysis reactor were selected to be GHSV, (catalytic) reaction temperature, and length ratio and numerical modeling was performed considering heat and fluid flow transfer as well as chemical reaction kinetics. Effect of the selected design parameters on the variation of conversion rate and reactant gas mixture concentration were comprehensively investigated to predict performance of COS hydrolysis reactor. Stochastic modeling of reactor performance was finally performed using Monte Carlo simulation and linear regression fitting.

The research community has shown significant interest in the aqueous synthesis of nanomaterials due to its ability to eliminate the need for complex organic solvents. This synthesis approach aligns with the principles of green chemistry, attracting considerable attention. Aqueous solution technology in fabricating nanostructures has gained recognition for its potential to create ultrasensitive, low-energy, and ultrafast optoelectronic devices. This report focuses on synthesizing lead iodide (PbI2) nanoplates using a water-based solution technique and fabricating a planar photodetector. The photodetectors with a planar type of device structure (ITO/PbI2 NPs/Au) demonstrated a remarkable photosensitivity of 3.9×103 and a photoresponsivity of 0.51 mA/W at a wavelength of 405 nm. Notably, the asymmetrical output properties of ITO/PbI2 NPs/Au detector deliver additional evidence of the effective creation of a Schottky contact. Thus, the photodetector exhibited a photoresponse even at 0 V bias, leading to the realization of self-powered photodetectors. Additionally, the device exhibited a rapid photoresponse of 0.21/0.38 s (−5 V) in the visible range. This study has expanded the horizons for the aqueous-phase synthesis of nanoplate nanostructures, enabling the large-area fabrication of high-performance photodetectors.

Accumulating reports have suggested that an inability to clear dead cells is a cause of inflammation and cancer and that the fascia is associated with cancer metastasis. Novel corpuscle-connected filiform structures (CCFSs) entangled on the fascia of the internal organs of rats were selectively visualized with high repeatability (93%) under vital staining with Janus Green B (JGB). Serial sections of CCFSs stained with haematoxylin and eosin and with Mattson Trichrome were microscopically examined. In parallel, the immunohistochemistry with CD31, Lyve 1, scanning electron microscopy, and transmission electron microscopy (TEM) were also used to investigate the novel properties of the CCFSs. All of the CCFSs enclosed JGB-stained granules, which was verified by the impromptu coupling of stereo and light microscopes and fluorescence-activated cell sorting. The functions of the CCFSs were discovered under fluorescence microscopy and confocal laser scanning microscopy to be implicated in cell death: fragmented DNAs and f-actins with extracellular DNAs. The dead cells in the CCFSs were verified by using terminal deoxynucleotidyl transferase dUTP nick end labelling and TEM. Moreover, the CCFS had a relatively-high concentration of calcium, a main element for cell death in tissue, which was measured in 2-dimensionally images using time-of-flight secondary ion mass spectrometry. Taken these results, we report for the first time that novel reticular CCFSs are widely entangled on the fascia of the internal organs of rats with the implication for cell death.

The causal effects of chondroitin, glucosamine, and vitamin/mineral supplement intake on kidney function remain unknown, despite being commonly used. We conducted a two-sample summary-level Mendelian randomization (MR) analysis to test for causal associations between regular dietary supplement intake and kidney function. Genetic instruments for chondroitin, glucosamine, and vitamin/mineral supplement intake were obtained from genome-wide association study of European ancestry. Summary statistics for the log-transformed estimated glomerular filtration rate (log-eGFR) were provided by the CKDGen consortium. The multiplicative random-effects inverse variance-weighted method showed that genetically predicted chondroitin and glucosamine intake was causally associated with a lower eGFR (chondroitin, eGFR change beta = -0.113 %, standard error (SE) = 0.03 %, P-value = 2E-04; glucosamine, eGFR change beta = -0.240 %, SE = 0.035 %, P-value = 6E-12). However, a genetically predicted vitamin/mineral supplement intake was associated with a higher eGFR (eGFR change beta = 1.426 %, SE = 0.136 %, P-value = 1E-25). Validation analyses and pleiotropy-robust MR results for chondroitin and vitamin/mineral supplement intake supported the main results. Our MR study suggests a potential causal effect of chondroitin and glucosamine intake on kidney function. Therefore, clinicians should carefully monitor their long-term effects.

The populations of clearwing moth borers in Korea have recently exploited and severe damage on pin oaks (Quercus palustris Munchh.). We conducted the field monitoring and the molecular analyses to identify them in an integrated manner. Morphological examination and molecular analyses on COI-gene based intra-and inter-specific genetic divergences (GD) were revealed that the borers were recognized as two invasive species, Sphecodoptera sheni and Paranthrenella pinoakula sp. nov.. The maximum intraspecific GD was found to be 1.9%, whereas the minimum interspecific GD was confirmed as 8.1%, with a distinct barcoding gap. Both MJ network and NJ tree were also showed that 18 haplotypes (HAPs) were detected from the 52 COI sequences. The borers were revealed total 17 HAPs: i) H1-H7 were detected from all seven regions with S. sheni; ii) Wonju and Goyang populations of S. sheni were revealed as more than three HAPs; iii) H7 was closely connected with H8 of Chinese population of S. sheni; iv) H9-H10 were detected as the other samples from Wonju population with P. pinoakula sp. n., and closely located with congeneric species. Maximum likelihood tree also revealed that P. pinoacula sp. n. nested within the congeneric species by genetically separating from the S. sheni.

In many of the current software applications, numerous vulnerabilities may be present.1 Attackers attempt to exploit existing vulnerabilities that lead to security breaches, unauthorized entry,2 data theft, or incapacitation of a computer system. Rather than addressing software or hardware3 vulnerabilities at a later stage, it is better to address them immediately. DevSecOps, when utilized4 in application development, tackles these vulnerabilities at an early stage. AIBughunter is a tool5 that addresses this problem in software and was developed by the ASWM research group to predict,6 classify, and repair software vulnerabilities. AIBughunter integrates LineVul to find vulnerable7 code lines and returns information about the type of vulnerability and its severity to developers.8 It also includes a tool, VulRepair, which detects and repairs vulnerabilities. VulRepair currently9 predicts patches for vulnerable functions at 44%. In order to become truly effective, this number 10 needs to be increased. This study examines VulRepair to see whether the 44% Perfect Prediction 11 can be increased. VulRepair is a T5 based model that uses Natural Language and Programming 12 Languages for pre-training along with Byte Pair Encoding. It outperforms other existing models, 13 such as VRepair and CodeBERT. However, the hyperparameters may not be optimized due to the 14 development of new optimizers. We review a Deep Neural Network (DNN) optimizer developed by 15 Google in 2023. This optimizer called Evolved Sign Momentum (LION) is available in PyTorch. We 16 applied this optimizer to VulRepair and tested its influence on hyperparameters. After adjusting the 17 hyperparameters, we obtained a 56% Perfect Prediction, which exceeds the value of the VulRepair 18 report of 44%. This means that VulRepair can repair more vulnerabilities and avoid more attacks. As 19 far as we know, our approach of utilizing an alternative to AdamW, the standard optimizer, has not 20 been previously applied to enhance VulRepair and similar models. 21

Residential segregation refers to the phenomenon where people of different socioeconomic backgrounds live in spatially separated areas. It is essential to ensure equitable access to urban amenities for all residents in pursuit of the normative values in urban planning. To achieve this planning goal, the disparity in accessibility to urban amenities needs to be appropriately diagnosed. Private apartments and public rental apartments are representative types of residences where residential segregation is likely to occur in the context of South Korea, since these two types show considerable differences in the education, income, and occupations. The objective of this study is to develop an analysis framework for diagnosing the difference in accessibility to urban amenities between the two residential types, and to empirically demonstrate their utility in the planning process. The empirical analysis conducted on Seoul revealed that not only were there significant local variations in accessibility between the two segregated residential areas, but the overall differences across the entire area were also pronounced. The proposed framework is useful in supporting decision-making processes for locating new public facilities or identifying regional priorities for guiding the placement of private amenities, with the aim of mitigating differences between segregated residential areas.

The present study was conducted to evaluate encapsulated essential oils as an alternative anticoccidial in coccidiosis vaccine challenged broiler chickens. A total of 600 day-old male broiler chicks were provided with no-added corn-soybean meal-based control diet or diets that contained either salinomycin or EO at 60 and 120 mg per kg of diet. On day 21, half of the control groups were orally challenged with a coccidiosis vaccine at 25 times higher than the recommended vaccine dose. During 22 to 28 days (i.e., one-week post coccidiosis vaccine challenge), the challenged chickens had decrease (P < 0.05) in body weight gain and feed intake but increase in feed conversion ratio compared with the non-challenged, naïve control chickens. However, dietary EO significantly counteracted (P < 0.05) coccidiosis vaccine-induced depression in body weight gain and feed intake. Increasing dietary EO linearly decreased (P < 0.05) the concentrations of the volatile fatty acids. Dietary SAL and EO affected gut morphology in chickens at 20 days posthatch. Increasing dietary EO linearly (P = 0.073) increased serum catalase activity. Collectively, our study shows that dietary EO increased coccidiosis vaccine-induced growth depression and altered gut physiology in broiler chickens.

An 8-month-old, 3.4 kg, castrated male Toy Poodle was referred for progressive tetraparesis and respiratory disorder without a history of trauma. Diagnostic imaging, including dynamic CT and MRI, revealed concurrent atlanto-occipital dislocation (AOD) and atlantoaxial instability (AAI) with spinal cord compression. This case was unique due to its congenital nature and the absence of trauma. The surgical intervention involved precise removal of the C1 vertebra's ventral articular facet, which was compressing on the spinal cord, attributed to its fixed and malaligned position within the atlantooccipital joint. Following facetectomy, the stabilization of the occipital bone to the C2 vertebra was achieved by screws, wire, and polymethyl methacrylate. Postoperative recovery was monitored with CT and radiographs, showing successful decompression and gradual improvement in gait, despite mild residual ataxia. The dog experienced postoperative complications with screw loosening at 114 days, which was managed successfully by extracting the problematic screws. Postoperatively, the dog showed a near-normal gait and experienced no pain through 21 months of monitoring. This case represents the first report of concurrent congenital AOD and AAI treated with ventral surgical approach, contributing new insights to the understanding and management of such complex cranio-cervical junction disorders in veterinary neurosurgery.

The post-weld heat treatment (PWHT) cracking susceptibility of a coarse grain heat-affected zone (CGHAZ) in SA213-T23 (2.25Cr-1.6W steel), used for boiler tubes employed in thermal power plants, was investigated using a Gleeble thermal cycle simulator. The PWHT cracking susceptibility test was performed at 650℃, 700℃ and 750℃, and it can be judged that the lower the reduce of area, the more susceptible it is to PWHT cracking. The results of the test also showed higher cracking susceptibility at 650℃ and 700℃, mostly involving intergranular fracture, while at 750℃, transgranular fracture was exhibited. Therefore, the PWHT cracking susceptibility is considered to be closely related to grain boundary. The microstructure of the simulated CGHAZ and PWHT at 650℃, 700℃and 750℃ was observed after etching with nital and alkaline sodium picrate etchants. Alkaline sodium picrate etched microstructures showed a white band at the grain boundary at 650℃, 700℃ and 750, that did not appear in nital etching. Analysis of the white band using EPMA, TEM and nanoindentation revealed that it was intergranular ferrite depleted with C, W and Cr as compared to that in the matrix. Based on these results, we investigated the mechanism of intergranular ferrite formation during PWHT and its effect on PWHT cracking susceptibility at 650℃, 700℃ and 750℃.

This study presents a comprehensive ecological evaluation of avian species based on 5,322 photographs obtained through camera-trap sampling. We identified 1,427 independent bird sightings, encompassing 26 families and 49 species. The study focused on temporal activity patterns, nesting behaviors, habitat preferences, and the overlap coefficient of activity patterns among 22 species of Passeriformes. Two species exhibited predominant morning activity, while five species were active in the afternoon, and 15 exhibited cathemeral activity (activity throughout the day). A cross-analysis revealed varying degrees of overlap in the activity patterns of pairs of species with similar behavioral ecology. Our findings indicate that despite exhibiting similar ecological behavior, these species display unique activity patterns, likely influenced by factors such as resource availability, competition avoidance, and thermoregulation strategies. The results highlight the richness and complexity of avian temporal niches and emphasize the need for further research into their correlation with environmental factors. This study contributes to a deeper understanding of niche separation within Passeriformes and expands our knowledge of avian behavioral ecology.

Cesium lead iodide (CsPbI3) perovskite nanocrystals (NCs) are a promising material for red light-emitting diodes (LEDs) due to their excellent color-purity and high luminous efficiency. However, small-sized CsPbI3 colloidal NCs, such as nanocubes, used in LEDs suffer from confinement effects, negatively impacting their photoluminescence quantum yield (PLQY) and overall efficiency. Here, we introduced YCl3 into the CsPbI3 perovskite, which formed anisotropic, one-dimensional (1D) nanorods. This was achieved by taking advantage of the difference in bond energies between Cl− and I− ions, which caused YCl3 to promote the anisotropic growth of CsPbI3 NCs. The YCl3-based nanorods improved the PLQY and storage stability by passivating the defects reducing the nonradiative recombination rates. When the YCl3-substituted CsPbI3 nanorods are applied to the emissive layer in LEDs, we achieve an external quantum efficiency of ~3.16% which is 1.86-fold higher than the pristine CsPbI3 NCs (1.69%) based LED. Notably, the ratio of horizontal transition dipole moments (TDMs) in the anisotropic YCl3:CsPbI3 nanorods was determined to be 75%, which is higher than the isotropically oriented TDMs in CsPbI3 nanocrystals (67%). This increased TDM ratio led to higher light outcoupling efficiency in nanorods-based LEDs. Overall, the results suggest that YCl3-substituted CsPbI3 nanorods could be promising for achieving high-performance perovskite LEDs.

Novel genetic and epigenetic factors involved in the development and prognosis of idiopathic pulmonary fibrosis (IPF) have been identified. We previously observed that EPB41L3 increased in the lung fibroblasts of IPF patients. Thus, we investigated the role of EPB41L3 in IPF by comparing EPB41L3 mRNA and protein expression of lung fibroblast between patients with IPF and controls. We also investigated the regulation of the epithelial-mesenchymal transition (EMT) in an epithelial cell line (A549), and the fibroblast-to-myofibroblast transition (FMT) in a fibroblast cell line (MRC5), by overexpressing and silencing EPB41L3. EPB41L3 mRNA and protein levels, as measured by RT-PCR, real-time PCR, and western blot, were significantly higher in fibroblasts derived from 14 IPF patients than in those from 10 controls. The mRNA and protein expression of EPB41L3 was upregulated during transforming growth factor-β-induced EMT and FMT. Overexpression of EPB41L3 in A549 cells using lenti-EPB41L3 transfection suppressed the mRNA and protein expression of N-cadherin and COL1A1. Treatment with EPB41L3 siRNA upregulated mRNA and protein expression of N-cadherin. Overexpression of EPB41L3 in MRC5 cells using lenti-EPB41L3 transfection suppressed mRNA and protein expression of fibronectin and α-SMA. Finally, treatment with EPB41L3 siRNA upregulated mRNA and protein expression of FN1, COL1A1, and VIM. Overall, these data strongly support an inhibitory effect of EPB41L3 on the process of fibrosis and suggest therapeutic potential of EPB41L3 as an anti-fibrotic mediator.

Tenascin C (TNC) is an element of the extracellular matrix (ECM) of various tissues, including the skin, and is involved in modulating ECM integrity and cell physiology. Although skin aging is apparently associated with changes in the ECM, little is known about the role of TNC in skin aging. Here we found that Tnc mRNA level was significantly reduced in the skin tissues of aged mice compared with young mice, consistent with reduced TNC protein expression in aged human skin. TNC-large (TNC-L; 330-kDa) and -small (TNC-S; 240-kDa) polypeptides were observed in conditional media from primary dermal fibroblasts. Both recombinant TNC polypeptides, corresponding to TNC-L and TNC-S, increased the expression of type I collagen and reduced the expression of matrix metalloproteinase-1 in fibroblasts. Treatment of fibroblasts with a recombinant TNC polypeptide, corresponding to TNC-L, induced phosphorylation of SMAD2 and SMAD3. TNC increased the level of TGF-β1 mRNA and upregulated the expression of type I collagen by activating the TGF-β signaling pathway. In addition, TNC also promoted the expression of type I collagen in fibroblasts embedded in a three-dimensional collagen matrix. Our findings suggest that TNC contributes to the integrity of ECM in young skin and to prevention of skin aging.

Ras homolog enriched in brain (Rheb1 and Rheb2), a small GTPase, regulates neuronal activity and has drawn attention for its implications in cancer development, especially breast cancer. This study explores the multifaceted role of Rheb1 in cancer, elucidating its involvement in crucial cel-lular processes such as proliferation, apoptosis resistance, migration, invasion, metastasis, and inflammatory responses. Despite these acknowledged connections, a comprehensive understanding of the intricate interplay between Rheb1 and cancer remains elusive. This review consolidates cur-rent knowledge on the impact of Rheb1 on cancer hallmarks and examines the potential of Rheb1 as a therapeutic target in cancer treatment. The review underscores the need for a more profound comprehension of the molecular mechanisms underlying Rheb1-mediated oncogenic processes. Furthermore, the review emphasizes the exploration of Rheb1 inhibitors as a promising avenue for cancer therapy. This study, by bringing to light the complex associations between Rheb1/Rheb2 and cancer, delivers valuable insights to the scientific community. These insights are instrumental in guiding the identification of novel targets and advancing the development of effective therapeu-tic strategies for treating cancer.

This paper presents a two-stage hierarchical neural network using image classification and object detection algorithms as key building blocks for a system that automatically detects a potential design right infringement. This neural network is trained to return the Top-N original design right records that highly resemble the input image of a counterfeit. Design rights specify the unique aesthetic characteristics of a product. Due to the rapid change of trends, new design rights are continuously generated. This work proposes an Ensemble Neural Network (ENN), an artificial neural network model that aims to deal with a large amount of counterfeit data and design right records that are frequently added and deleted. At first, we performed image classification and objection detection learning per design right using the existing models with a proven track record of high accuracy. The distributed models form the backbone of the ENN and yield intermediate results aggregated at a master neural network. This master neural network is a deep residual network paired with a fully connected network. This ensemble layer is trained to determine the sub-models that return the best result for a given input image of a product. In the final stage, the ENN model multiples the inferred similarity coefficients to the weighted input vectors produced by the individual sub-models to assess the similarity between the test input image and the existing product design rights to see any sign of violation. Given 84 design rights and the sample product images taken meticulously under various conditions, our ENN model achieved average Top-1 and Top-3 accuracies of 98.409% and 99.460%, respectively. Upon introducing new design rights data, a partial update of the inference model was done an order of magnitude faster than the single model. ENN maintained a high level of accuracy as it scaled out to handle more design rights. Therefore, the ENN model is expected to offer practical help to the inspectors in the field, such as the customs at the border that deal with a swarm of products.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

Disease detection and prediction have been one of the most frequent uses of machine learning models in the last decade, and Parkinson's disease is no exception. It is common for people in their old age to have one form of disease or another depending on the circumstances in which they find themselves. This study analyzed and evaluated various supervised machine learning models to detect the presence of Parkinson's disease in elderly individuals. An extreme gradient boosting model, along with other models, such as naïve Bayes, random forest, K-nearest neighbor, and support vector machine (SVM), was implemented to determine the best outcome. The extreme gradient boosting (XGBoost) model is a powerful boosting machine learning technique, particularly in terms of speed and accuracy. The results showed that the XGBoost model, which is an optimized version of the other boosting models, is capable of projecting the presence of Parkinson's disease with very high accuracy compared to other algorithms. The implemented classification algorithm extreme gradient boosting method achieved approximately 98 % accuracy, 97.5 % precision, 100.0 % recall, and 98.7% f1-score which are high compared with the results found in the existing literature.

This study investigated clinical nurses’ knowledge and visual differentiation ability of the pressure injury classification system (PICS) and incontinence-associated dermatitis (IAD), additionally analyzing possible influencing factors. A convenience sample of 248 nurses took the PICS and IAD knowledge test (KT) and completed the visual differentiation ability test (VDAT), consisting of 21 photographs with clinical information. The overall mean score for correct answers was 12.65±2.90 points in PICS & IAD KT and 11.43±4.57 points in VDAT. Incorrect responses were most common for statements related to stage Ⅱ, Ⅲ, IAD for PICS & IAD KT, and deep tissue pressure injury (DTPI), unstageable, and stage Ⅲ for VDAT. Significant correlations were found between PICS & IAD KT and VDAT (r=.252, p<.001). Factors affecting scores for VDAT were the scores of PICS & IAD KT, debridement experience in nursing patients with PI, and the management frequency of PI and IAD. Results indicate that nurses have an overall understanding of PICS and IAD, but low visual differentiation ability regarding stage Ⅲ, DTPI, and unstageable PI. Continuing education is needed to further improve knowledge and visual differentiation ability for PICS and IAD.

Bangladeshi medicinal plants (BMP) have been used as traditional medicinal plants to treat chronic inflammatory diseases, but the antioxidant and anti-inflammatory effects of the bark of BMP are not yet known. The objective of this study was to determine antioxidant and anti-inflammatory activities using methanolic extracts of bark obtained from 15 medicinal spices of Bangladesh plants. The bark methanol extracts of BMP evaluated the total antioxidant activity and anti-inflammatory effect of lipopolysaccharide (LPS)-induced inflammation in RAW 264.7 macrophages. Among the 15 bark extracts of BMP, Albizia odoratissima (A. odoratissima), Engelhardia spicata (E. spicata), and Shorea robusta (S. robusta) showed the highest total phenolic contents and total antioxidant capacity by reducing free radicals scavenging activity. In particular, the three bark extracts significantly reduced the mRNA expression of LPS-induced inflammatory cytokines and inflammation-inducible enzymes in macrophages. Also, the mRNA expression of NADPH oxidase 2 was significantly suppressed by three bark extracts in LPS-induced RAW 264.7 macrophages. The results suggest that among the 15 bark extracts obtained from medicinal plant in Bangladesh, three bark extracts of A. odoratissima, E. spicata, and S. robusta exert total antioxidant capacity by reducing free radicals scavenging activity and inhibitory effects on LPS-stimulated inflammation in macrophages.

In the present era, infertility is one of the major issues which restricts many couples to have their own kids. Infertility is the inability to achieve a clinical pregnancy after regular unprotected sexual intercourse for the period of one year or more. Various factors including defective male or female germ cell development, unhealthy and improper lifestyles, diseases like cancer and associated chemo-or-radiation therapies, congenital disorders etc. may be responsible for infertility. Therefore, it is highly important to understand the basic concepts of germ cell development including primordial germ cell (PGC) formation, specification, migration, entry to genital ridges and their molecular mechanisms, activated pathways, paracrine and autocrine signaling, along with possible alteration which can hamper germ cell development and can cause adversities like cancer progression and infertility. Knowing all these aspects in a proper way can be very much helpful in improving our understanding about gametogenesis and finding possible ways to cure related disorders. Here in this review, various aspects of gametogenesis especially female gametes and relevant factors causing functional impairment have been thoroughly discussed.

Perfluorinated compounds (PFCs) are used in the manufacturing process of the semiconductor and display industries, and the need for emission reduction is growing as a greenhouse gas with a very large global warming potential. The decomposition characteristics of etch type and water film (WF) type plasma-wet scrubbers were investigated. The PFCs used in the study were CF4, SF6, NF3, CHF3, C2F6, C3F8, and C4F8, and the destruction removal efficiency (DRE) and by-product gas generation rate according to the changes in the parameters (total flow rate and power) of the plasma-wet scrubber were confirmed. When the total flow rate was 100 L/min and the measured maximum power (11 kW), the reduction efficiency of CF4 in the etch type was 95.60 % and the DRE of other PFCs was 99.99 %. And, in the WF type, the DRE of CF4 was 90.06 %, that of SF6 was 96.44 %, and that of other PFCs was 99.99 %. When the total flow rate was 300 L/min and 11 kW, the DRE of SF6 in the etch type was 99 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. And, in the WF type, the DRE of SF6 was 94.39 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. The by-product gas generation rate was significantly lower in the WF type.

This study uses explainable artificial intelligence to analyze major predictors of poor self-rated health, dementia and their comorbidity, which include various aspects of social support. Data came from the Korean Longitudinal Study of Ageing (2016-2018), with 5527 participants aged 56 or more. The dependent variables were: (1) poor self-rated health (SRH) with 5 categories (very good, good, middle, poor, very poor); (2) dementia (no, yes); and (3) their comorbidity with 4 categories (SRH very good, good or middle, dementia no; SRH very good, good or middle, dementia yes; SRH poor or very poor, dementia no; SRH poor or very poor, dementia yes). The 49 demographic, socioeconomic and health-related predictors were included. The accuracy and area under the receiver operating characteristic curve (AUC) were compared for logistic regression and the random forest. Logistic regression and the random forest registered similar AUCs with the range of 0.80-0.87. Based on random forest variable importance, 18 out of top-20 predictors were identical for SRH, dementia and their comorbidity: previous SRH, life satisfaction - health, age, body mass index, income, chronic diseases, life satisfaction - economic, life satisfaction - overall, grandchildren alive, friendship meeting, brothers/sisters alive, class identity, children alive, social activity - friendship, education, children in weekly contact, religion and drinker. However, some variations were found among the three dependent variables, i.e., previous SRH for comorbidity (1st) and SRH (1st) compared to dementia (11th), grandchildren alive for SRH (6th) and dementia (4th) compared to comorbidity (9th), chronic diseases for comorbidity (6th) compared to SRH (10th) and dementia (10th). In terms of Shapley Additive Explanation (SHAP) values, the probability of dementia is expected to decrease by 5.57% in case a predictor grandchildren alive is included to the model. This study highlights the importance of social support for the prediction of poor self-rated health, dementia and their comorbidity. Specifically, the promotion of family support and friendship activity for elders would be vital for the prevention and management of their self-rated health and dementia.

Hair loss attributed to excessive stress from work and lifestyle changes has become a growing concern, particularly among young individuals. However, currently used drugs such as minoxidil and finasteride impose a plethora of side effects. Therefore, natural substances as alternatives have garnered research interest. A recent study showed the efficacy of Malva verticillata seed extracts in alleviating hair loss via upregulation of the Wnt/β-catenin signaling pathway. In this study, the efficacy of M. verticillata seed extracts on alleviation of hair loss was further investigated. Further fractionation and purification of the seed extracts using silica gel column chromatography and preparative high-performance liquid chromatography helped identify linoleic acid (LA) and oleic acid as the major bioactive components. LA insufficiency is reported to cause hair loss. However, its mechanism of action is not clearly known. Here, we explored the efficacy of LA treatment on preventing hair loss and its underlying mechanism of action. We found that LA treatment activated Wnt/β-catenin signaling and induced dermal papilla cell (DPC) proliferation in cell proliferation assays. Moreover, it increased the expression of cell cycle proteins such as cyclin D1 and cyclin-dependent kinase 2. LA treatment also increased the expression of vascular endothelial growth factor, insulin-like growth factor-1, hepatocyte growth factor, and keratinocyte growth factor in a concentration-dependent manner and significantly inhibited that of DKK-1, induced by dihydrotestosterone. These findings suggest that LA treatment induces hair growth by increasing DPC proliferation and alleviates androgenic alopecia by activating Wnt/β-catenin signaling in DPCs.

Accurate evaluation of thermo-fluid dynamic characteristics in tank are critically important for designing liquid hydrogen tank of small-scale hydrogen liquefier to minimize heat in-leak into the liquid and ullage. Due to the huge cost, most future liquid hydrogen storage tank designs will have to rely on predictive computational models for storage tank pressurization and heat-leak minimization. Thus, reliable on predictive numerical models to aid design process of tank design have been required. Therefore, in this study, in order to improve the storage efficiency of the small-scale hydrogen liquefier, a three-dimensional CFD model that can predict the boil-off rate and the thermo-fluid characteristics due to heat penetration has been developed. The prediction performance and accuracy of the CFD model is validated on the basis of the comparisons between its results and previous experimental data and a good agreement is obtained. To evaluate insulation performance of polyurethane foam according to thickness, the pressure change and thermo-fluid characteristics in a partially liquid hydrogen tank, subject to fixed ambient temperature and wind velocity, has been investigated numerically. Three different insulation thickness were considered to investigate not only interfacial characteristics between liquid and ullage but thermo-fluid dynamics in hydrogen storage tank for various heat-leak situation. The results indicate that as the insulation thickness becomes thinner and more heat penetration exists, natural convection by buoyancy develops stronger, so strong vortices are created near the interfacial zone by upward flow driven by buoyancy. In particular, as the amount of heat in-leak increased, wider and stronger heat accumulation was found in the top dished head area of the ullage area. In addition, it was confirmed that the CFD model developed in this study could well describe the phenomenon in which the temperature of the tank wall and the insulation mat increased at a faster rate due to faster heat transfer from the vapor and interface. In the future, the numerical model developed in this study will be used for optimizing insulation system of storage tank for small-scale hydrogen which is cost-effective and highly efficient.

Background Despite the high vaccination coverage rate, in-hospital transmission of measles continues to occur in South Korea. We present a measles outbreak in which two healthcare workers (HCWs) with presumptive evidence of measles immunity were infected by a patient with typical measles at a single hospital in South Korea. This facilitated the evaluation of measles seroprevalence in all HCWs. Methods In 2018, suspected patients and contacts exposed during a measles outbreak were investigated based on their medical histories and vaccination status. Cases were confirmed by the detection of measles-specific immunoglobulin M or RNA. After the measles outbreak, all HCWs underwent measles IgG testing for point-prevalence surveillance. In addition, we have routinely performed measles IgG tests on new HCWs since 2019. The measles vaccine was administered to HCWs who tested negative or equivocally negative for IgG antibodies. Results An index patient who returned from China with fever and rash was diagnosed with measles at a hospital in Korea. Two additional HCWs were revealed as measles cases: one was vaccinated with the 2-dose measles–mumps–rubella (MMR) vaccine, and the other, who was born in 1967, was presumed to have immunity from natural infection in South Korea. All three patients harbored the same D8 genotype. No additional measles cases were identified among the 964 contacts of secondary patients. After the measles outbreak, 2,310 HCWs underwent measles IgG tests. The average age at the time of the test was 32.6 years, and 74.3% were female. The overall seropositivity of measles was 88.9% (95% confidence interval, 87.5 –90.1). Although the birth cohorts between 1985 and 1994 were presumed to have received the measles-rubella (MR) catch-up vaccination in 2001, 175 (89.3%) HCWs were born after 1985 among the 195 seronegative cases. Conclusion Despite high population immunity, imported measles transmission occurred among HCWs, with presumed immunity. This report underscores the importance of understanding the prevalence of measles susceptibility among newly employed HCWs. This is important for policymaking regarding hospital-wide vaccinations to prevent vaccine-preventable diseases.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

The central nervous system (CNS) is the final frontier in drug delivery because of the blood-brain barrier (BBB), which poses significant barriers to the access of most drugs to their targets. Kynurenic acid (KYNA), a tryptophan (Trp) metabolite, plays an important role in behavioral functions and abnormal KYNA levels have been observed in neuropsychiatric conditions. The current challenge lies in delivering KYNA to the CNS owing to its polar side chain. Recently, C-3 side chain modified KYNA analogs have been shown to cross the BBB; however, it is unclear whether they retain the biological functions of the parent molecule. This study examined the impact of KYNA analogs, specifically SZR-72, SZR-104, and the newly developed SZRG-21, on behavior. The analogs were administered intracerebroventricularly (i.c.v.), and their effects on the motor domain were compared with those of KYNA. Specifically, open field (OF) and rotarod (RR) tests were employed to assess motor activity and skills. SZR-104 increased horizontal exploratory activity in the OF test at a dose of 0.04 μmol/4 μL, while SZR-72 decreased vertical activity at doses of 0.04 and 0.1 μmol/4 μL. In the RR test, however, neither KYNA nor its analogs showed any significant differences in motor skills at either dose. Side chain modification affects affective motor performance and exploratory behavior, as the results show for the first time. In this study, we showed that KYNA analogs alter emotional components such as motor-associated curiosity and emotions. Consequently, drug design necessitates the development of precise strategies to traverse the BBB while paying close attention to modifications in their effects on behavior.

Delve into the dynamic realms of neuroscience, neurology, and psychiatry with this groundbreaking editorial, unveiling the intricate mechanisms of brain function and dysfunction. Explore the latest advancements in molecular biology, genetics, epigenetics, pharmacology, and neuroimaging that are revolutionizing our understanding of neurological and psychiatric disorders. Uncover the challenges and gaps in translating cutting-edge research into practical clinical applications, aiming to enhance the lives of patients and their families. Discover the pivotal role of neuroplasticity in reshaping the brain's adaptability throughout life, alongside the promising potential of non-invasive brain stimulation techniques like transcranial magnetic stimulation and transcranial direct current stimulation. Embark on a journey of innovation and collaboration as researchers and clinicians strive to bridge the gap between bench and bedside, offering hope for improved diagnosis, prevention, and treatment of complex neurological and psychiatric conditions. Join us in this exploration of transformative ideas and novel interventions that hold the key to a brighter future for individuals and society.

Hair loss attributed to excessive stress from work and lifestyle changes has become a growing concern, particularly among young individuals. However, currently used drugs such as minoxidil and finasteride impose a plethora of side effects. Therefore, natural substances as alternatives have garnered research interest. A recent study showed the efficacy of Malva verticillata seed extracts in alleviating hair loss via upregulation of the Wnt/β-catenin signaling pathway. In this study, the efficacy of M. verticillata seed extracts on alleviation of hair loss was further investigated. Further fractionation and purification of the seed extracts using silica gel column chromatography and preparative high-performance liquid chromatography helped identify linoleic acid (LA) and oleic acid as the major bioactive components. LA insufficiency is reported to cause hair loss. However, its mechanism of action is not clearly known. Here, we explored the efficacy of LA treatment on preventing hair loss and its underlying mechanism of action. We found that LA treatment activated Wnt/β-catenin signaling and induced dermal papilla cell (DPC) proliferation in cell proliferation assays. Moreover, it increased the expression of cell cycle proteins such as cyclin D1 and cyclin-dependent kinase 2. LA treatment also increased the expression of vascular endothelial growth factor, insulin-like growth factor-1, hepatocyte growth factor, and keratinocyte growth factor in a concentration-dependent manner and significantly inhibited that of DKK-1, induced by dihydrotestosterone. These findings suggest that LA treatment induces hair growth by increasing DPC proliferation and alleviates androgenic alopecia by activating Wnt/β-catenin signaling in DPCs.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

The chemopreventive effects of various mixed cereal grain (MCG) samples on azoxymethane (AOM, 10 mg/kg) and dextran sulfate sodium (DSS, 2% w/v)-induced colorectal cancer (CRC) in C57BL/6J mice were studied. The main MCG preparation consisted of fermented brown rice (FBR), glutinous brown rice, glutinous Sorghum bicolor, glutinous Panicum miliaceum, Coix lacryma-jobi and black soybean at an appropriate mixing ratio. Other MCG preparations contained rice coated with 5% Phellinus linteus and 5% Curcuma longa (MGR-PC), or 10% Phellinus linteus (MCG-P), or 10% Curcuma longa (MCG-C). Consumption of dietary MCG-PC by CRC mice significantly increased colon length, decreased the ratio of colon weight to length, and reduced the number of colon tumors. Similar effects, although to a lower extent, were observed in CRC mice fed with MCG-P, followed by those fed with MCG-C, MCG, FBR or white rice (WR). MCG-PC significantly suppressed colonic neoplasia, and decreased the levels of various cytokines (tumor necrosis factor: Tnf, interleukin 1 beta: Il1b, interleukin 6: Il6, and interferon gamma: Ifng) in serum and colon tissue of the CRC mice. In addition, MCG-PC increased the mRNA expressions of tumor protein p53(Tp53) and cyclin-dependent kinase inhibitor 1A(Cdkn1a), activated pro-apoptotic caspase 3(Casp3), and reduced expression of both mRNA and protein of inducible inducible nitric oxide synthase 2 (Nos2), prostaglandin-endoperoxide synthase 2 (Ptgs2), and cyclin D1(Ccnd1) in colon tissue. These findings suggest that than compared with other cereal grain preparations, MCG-PC had a greater activity against AOM/DSS-induced CRC by reducing intestinal inflammation, and modulating the expression of certain carcinogenesis related factors (Nos2, Ptgs2, Tp53, Cdkn1a, Ccnd1 and Casp3) in colon tissue of CRC mice.

The objective of this study was to evaluate the effects of dietary supplementation with bacteriophage and β-mannanase on health and growth performance in calves. Thirty-six pre-weaning male Holstein calves were randomly allocated to one of four dietary treatments: no supplementation, 0.1% β-mannanase, 0.1% bacteriophage, and both 0.1% bacteriophage and β-mannanase supplementation in a starter. The experiment lasted from 2 weeks before weaning to 8 weeks after weaning. Twenty-two calves survived to the end of the experiment. No interaction was observed between the two methods of supplementation. A 1-kg increase in initial BW resulted in a 1.41-fold increase in the odds ratio of survival (p < 0.01). The bacteriophage supplementation tended to increase the odds ratio of survival (p = 0.09). The number of Escherichia coli in feces significantly decreased one week after weaning. β-mannanase supplementation increased the concentrates intake (p < 0.01) and tended to increase the final BW (p = 0.08). Analysis of repeated measures indicated β-mannanase supplementation increased weekly body weight gain (p = 0.018). We conclude that bacteriophage supplementation may have a positive effect on calf survival rate, while β-mannanase supplementation may increase the growth rate and intake of a starter in calves.

Neurodegeneration is a major problem in neuroscience and medicine as it causes and worsens many neurological and psychiatric disorders. It involves gradual loss of neurons at different levels of the brain, affecting cognition, emotion, behavior, consciousness, and attention. Understanding the causes and consequences of neurodegeneration is crucial for identifying the risk factors, biomarkers, and treatments. However, the current therapies are mostly symptomatic and ineffective. Therefore, new and innovative methods, such as noninvasive brain stimulation (NIBS), are needed to modulate brain activity and plasticity in a safe and reversible manner. This field is rapidly developing, with a focus on exploring new clinical applications, mechanisms, and combinations of NIBS and drugs. This special issue covers the latest progress and challenges in the study of neurodegeneration in cognitive impairment and mood disorders from the experimental, clinical, and translational perspectives. It addresses the complexity and diversity of these conditions, the lack of disease-modifying treatments, the ethical and practical issues of conducting research in vulnerable and diverse populations, the integration and interpretation of data from multiple sources and modalities, and the development and validation of novel methods such as NIBS, artificial intelligence, and drug repurposing. Collaborative efforts among various stakeholders are needed to improve our knowledge and treatment of neurodegeneration underlying cognitive impairment and mood disorders.

Antibiotics’ effect on Mycoplasma pneumoniae (MP) infection still remains controversial. A prospective study of 257 children with MP pneumonia during a recent epidemic (2015-2016) was conducted. All MP pneumonia patients were treated with corticosteroids within 24-36 h after admission. Initially, oral prednisolone (1 mg/kg) or intravenous methylprednisolone (IVMP) (1-2 mg/kg) was administered for mild pneumonia patients, and IVMP (5 -10 mg/kg/day) for severe pneumonia patients. If patients showed persistent fever for 36-48 hours or disease progression, additive IVMP (5 mg/kg or 10 mg/kg) was given. Eighty-five patients received only a broad-spectrum antibiotic without macrolide. The mean age and the male:female ratio were 5.6 ± 3.1 years, respectively. Seventy-four percent of patients (190/257) showed immediate defervescence within 24 h, and 95.7% (246/257) of patients showed defervescence within 72 h with improvements in clinical symptoms. Eight patients who received additive IVMP also showed clinical improvement within 48 h without adverse reactions. There were no clinical or laboratory differences between patients treated with a macrolide (n = 172) and without (n = 85). Early corticosteroid therapy might reduce disease morbidity and prevent disease progression in MP pneumonia patients without side effects, and antibiotics may have limited effects on MP infection.

This study aimed to investigate the effects of jet-milling on lutein extraction contents of spinach powder (SP) and pulsed electric fields as a non-thermal pasteurization technology on spinach juice (SJ) to preserve lutein contents. SP particles were divided into SP-coarse (Dv50 = 315.2 μm), SP-fine (Dv50 = 125.20 μm), and SP-superfine (Dv50 = 5.59 μm) fractions and SP-superfine was added to SJ due to the highest contents of lutein extract. The PEF and thermal treatment were applied to evaluate the effects of preserving the lutein content of PEF during storage (25 days). The juice after being designated to untreated (no pasteurization), PEF1,2 (SJ treated with PEF 20 kV/cm 110 kJ/L, 150 kJ/L), Thermal1,2 (SJ treated with 90 ℃, 10 min and 121 ℃, 15 min). The sizes and surface shapes of superfine SP particles were more homogeneous and smoother than the other samples. SJ made with SP-superfine and treated by PEF had the highest lutein content and antioxidant activities among the group. Complex of jet-milling and PEF pasteurization could be great potential technologies to improve the lutein contents of lutein-enriched juice in the food industry.

Some time ago, Kobayashi et al. experimentally studied the so-called Lee-Naughton-Lebed's (LNL) angular effect in strong electric fields [K. Kobayashi, M. Saito, E. Omichi, and T. Osada, Phys. Rev. Lett. \textbf{96}, 126601 (2006)]. They found that strong electric fields split the LNL conductivity maxima in $\alpha$-(ET)$_2$-based organic conductor and hypothetically introduced the corresponding equation for conductivity. In this Letter, for the first time we suggest quantum mechanical theory of the LNL angular oscillations in moderately strong electric fields. In particular, we demonstrate that the obtained by us approximate theoretical formula coincides with the hypothetical one and well describes the above mentioned experiments.

Porcine parvovirus (PPV) 1 is a major causative pathogen of reproductive failure, and porcine circovirus (PCV) 2 is an etiological pathogen causing PCV-associated and PCV diseases worldwide. PPV2–6 and PCV3 were recently identified as newly emerging viruses with unknown pathogeneses. However, little is known of PPV1–6 and PCV3 effects or their co-infections with PCV2. In this study, we examined 926 samples (272 aborted pig fetuses and 654 pig lung tissues) from domestic pig farms for the presence of PPV1–6 or PCV3 and for PCV2 co-infection with these seven viruses. The prevalence of PPV and PCV was significantly greater in lung tissue samples than aborted pig fetus samples. PPV3–6 were detected for the first time in Korean domestic pigs. Co-infection rates with PCV2 and other viruses were significantly higher in abattoir samples than that in aborted pig fetus samples. Concurrent infections are more common than single infection in pig population and nu-merous infectious pathogens such as PPV and PCV2 can impact the respiratory diseases. Fur-thermore, Korean PPV1 strain (PPV1-82) was identical to the virulent PPV-27a strain in this respect. Our results describe, for the first time the prevalence of PPV1–6 and PCV3 infections and their co-infection rates with PCV2 in Korean domestic pigs.

Advancements in 3D printing technologies have led to new implementations in rapid prototyping, microfluidics, tooling, dentistry, biomedical devices, drug delivery, and tissue engineering. Stereolithography techniques, which are photopolymerization-based processes, contribute to the optical, chemical, and mechanical properties of 3D printed materials using versatile polymer chemistry. This study used potassium titanate powder (K2Ti8O17) as an additive to enhance the mechanical strength of photocurable resins. PEG was selected as the stabilizer to optimize the dispersion and precipitation of potassium titanate. The flexural strength, hardness, and tensile strength were compared to assess the mechanical strength of the 3D printing resin. The flexural strengths of the printed specimens were in the range of 15–39 N/mm2. The measured surface hardness and tensile strength were 41–80 HV and 2.3–15 N/mm2, respectively. The output resolution of the potassium titanate/acrylate resin was tested using a line-pattern structure. 3D printing resin without stabilizers produced lines with a thickness of 0.3 mm, whereas 3D printing resin containing a stabilizer produced lines with a thickness of 0.2 mm. The flexural strength and pattern thickness results suggest that the potassium titanate/acrylate resin can be utilized as a 3D printer resin, suggesting new possibilities for potassium titanate materials.

The effect of CO2 pre-treatments on tomato quality prior to cold storage was investigated using physiochemical and transcriptome changes. Three hours CO2 treated fruits were firmer than untreated fruits and had a good appearance even after being transferred from 4°C storage to 20°C for 8 d. CO2 pretreatment with cold storage showed a synergistic effect on delayed ripening through reduced respiration; these tomatoes exhibited a lower lycopene content than untreated fruit under cold storage. Tomatoes treated with 30% CO2 had fewer pits than untreated fruits subjected to chilling temperatures, even after being transferred to 20°C for 8 d. Functional enrichment analyses from transcriptome and metabolome commonly showed that CO2-responsive genes or metabolites were involved in the sucrose and starch and biosynthesis of secondary metabolisms. The most frequently detected domain, ethylene-responsive factor domain and reduced glycolysis provide insights into the mechanism that CO2 regulates tomato quality.

This study explores the potential of titanium disulfide (TiS2) as an active material for aqueous calcium-ion batteries (CIBs). We investigate the electrochemical redox reactions of calcium ions within TiS2 and assess its suitability for use in aqueous CIBs. Additionally, we examine the im-pact of different electrolyte concentrations on TiS2 electrode reactions. Our findings reveal that TiS2 exhibits distinct charge-discharge behaviors in various aqueous calcium-ion electrolytes. Notably, at higher electrolyte concentrations, TiS2 effectively suppresses the hydrogen genera-tion reaction caused by water decomposition, demonstrating its potential as an active material for aqueous CIBs. In-situ X-ray diffraction analysis confirms the intercalation of Ca2+ ions be-tween TiS2 layers during charging. This confirmation is groundbreaking, as it represents the first experimental evidence of calcium ions being electrochemically inserted between TiS2 layers from aqueous solutions, signifying a previously unreported achievement and strongly suggesting TiS2's applicability in aqueous CIBs. X-ray photoelectron spectroscopy analysis further supports the formation of a solid electrolyte interphase (SEI) on the TiS2 electrode surface, contributing to the suppression of electrolyte decomposition reactions. Furthermore, we investigate the influ-ence of anions in the electrolyte on charge-discharge behavior. Our findings suggest that the choice of anion coordinated with Ca2+ ions affects SEI formation and cycling performance. Un-derstanding the role of anions in SEI formation is crucial for optimizing aqueous CIBs. In con-clusion, this research underscores TiS2's potential as an active material for aqueous calcium-ion batteries and emphasizes the importance of electrolyte composition in influencing SEI formation and battery performance. These findings contribute to the development of more sustainable and efficient energy storage technologies.

Studies have shown increased nontuberculous mycobacterial pulmonary disease (NTM) incidence with inhaled corticosteroid (ICS) use in patients with chronic respiratory diseases; however, this association in chronic obstructive pulmonary disease (COPD) remains insufficiently studied. Using a nationwide population-based database of the Korean National Health Insurance Service, newly diagnosed COPD patients (20052018) treated with inhaled bronchodilators were selected. An NTM case was defined by the presence of the first diagnostic code following inhaled bronchodilator use. Results indicated that ICS users did not have an increased risk of NTM disease compared to non-ICS users (hazard ratio [HR], 1.121; 95% confidence interval [CI], 0.9501.323; p = 0.1755). The highest quartile of the cumulative ICS dose was associated with the development of NTM (1.200, 0.9501.323, p = 0.0497). Medium (1.229, 1.0081.499, p = 0.0410) and high daily doses of ICS (1.637, 1.2412.160, p = 0.0005) were associated with an increased risk of NTM disease. There was no difference in the risk of NTM according to ICS type. ICS use may not increase the risk of developing NTM disease in patients with COPD. However, physicians should weigh the potential benefits and risks of ICS, especially when using high doses and prolonged durations.

This study aims at an acoustic design of the classical concert hall and evaluation of the acoustic performance. In terms of three acoustic parameters (i.e., reverberation time (RT), clarity (C80), and lateral fraction (LF)), this study performed acoustic simulation modeling and site measurement with the K Art Hall located in South Korea as a case study. First, in order to meet the acoustic performance of the K Art Hall (target RT: 1.4~1.7 seconds, target C80: -2dB or more +2dB or less, and target LF: 10~35%), the finish materials and shape of the room as an interior acoustic design were determined. Second, the average values of the RT, C80, and LF using the acoustic simulation modeling were estimated at 1.4 second, 1.2~1.6 dB, and 29%, respectively. Third, the average values of the RT, C80, and LF through site measuring were measured at 1.5~1.64 second, 0.07~1.31dB, and 22.22~31.37%, respectively. Thus, the results of both the acoustic simulation modeling and site measuring were analyzed so as to satisfy the target acoustic performance. The results of this study will help the decision-makers (i.e., owner, construction managers, etc.) to plan the classical concert hall in terms of the RT, C80, and LF.

Osteoporosis, often linked to increased osteoclast activity due to menopause or aging, was the focus. In this study, the inhibitory effects of Salicornia europaea L. (SE) water extract of desalted SE (WSE) were investigated on osteoclast differentiation and bone loss in ovariectomized mice. The findings revealed that WSE effectively inhibited RANKL-induced osteoclast differentiation, as evidenced by TRAP staining, and also suppressed bone resorption and F-actin ring formation in a dose-dependent manner. Gene expressions related to osteoclast differentiation, including NFATc1, TRAP, cathepsin K, and DC-STAMP, were downregulated by WSE. Oral administration of WSE improved bone density and structural parameters in ovariectomized mice. Dicaffeoyl quinic acids (DCQAs) and saponins in WSE were detected, with 3,4-, 3,5-, and 4,5-DCQA isolated and identified. All tested DCQAs, including the aforementioned types, inhibited osteoclast differentiation, bone resorption, and the expression of osteoclast-related genes. Furthermore, WSE and DCQAs reduced ROS production mediated by RANKL. These results indicate the potential of WSE and its components, DCQA, as preventive or therapeutic agents against osteoporosis and related conditions.

This study investigates the application of frequency augmentation techniques to improve condition-based maintenance (CBM+) systems for airborne weapon systems, focusing on the predictive accuracy of velocity and acceleration parameters. Utilizing MIL-STD-1553B MUX data from 138 sorties of fixed-wing aircraft, we explored six augmentation methods, including traditional interpolations (linear, quadratic, cubic spline) and advanced machine learning models (K-Nearest Neighbor, LSTM, and Bi-LSTM). Our findings indicate that while traditional methods like linear interpolation are more effective for velocity parameters, advanced ML techniques, particularly Bi-LSTM, provide better results for acceleration parameters, which exhibit more complex and rapid variability. The study underscores the necessity of tailoring augmentation approaches to specific parameter characteristics and highlights the potential of ML models in capturing intricate patterns within time-series data. These insights are critical for advancing CBM+ systems in military avionics, enhancing reliability and operational efficiency through improved data processing strategies. Future work should explore more performant augmentation techniques, such as by integrating multi-dimensional datasets, and explore ways to develop automated tools for a more powerful predictive maintenance framework.

Noninvasive and portable diagnoses via angle-resolved coherent spectral data are presented. ACTIRS (Angle- resolved coherent tomographic IR spectroscopy) through angle-coherent return spectra from photonic quantum ring laser of whispering gallery modes, which is not photocurrent-converted after the cortical, vascular or muscular diffuse paths, can be a new method for brain/heart studies. Also it will be eligible for frequent do-it-yourself diagnoses of breast cancer before hospital visits. The unique angle-coherent multi-spectra will eventually lead to study ionic or protein contents of cranial, arterial or lactiferous ducts that have been obtained only from uncomfortable biopsy, NMR, CT or mammography. The spectral data can be spatially or temporally improved and correlated for extracting more meaningful diagnostic conclusions

A cell filtration platform that affords accurate size separation and minimizes fouling was developed. The platform features an ultra-thin porous membrane (UPM) filter, a pumping head for backflushing (PHB), and cell size measurement (CSM) software. The UPM chip is an ultrathin free-standing membrane with a large window area of 0.68 mm2, a pore diameter of 5 to 9 μm, and a thickness of less than 0.9 μm. The PHB prevents filter fouling. The CSM software analyzes the size distributions of the supernatants and subnatants of isolated cells and presents the data visually. The D99 particle size of cells of the chronic myeloid leukemia (CML) line K562 decreased from 22.2 to 17.5 μm after passage through a 5-μm filter. K562 cells could be separated by careful selection of the pore size; the recovery rate attained 91.3%. The method was compared to conventional blocking models by evaluating the mean square errors (MSEs) between the measured and calculated filtering volumes. The filtering rate was fitted by a linear regression model with a significance that exceeded 0.99 based on the R2 value. The platform can be used to separate various soft biomaterials and affords excellent stability during filtration.

Heavy metals, including arsenic from abandoned mines, are easily transported with sediment and deposited in water bodies such as reservoirs and lakes, creating critical water quality issues when they are released. Understanding the leaching of heavy metals is necessary for developing efficient water quality improvement plans. This study investigated how arsenic leaches from different soil types and responds to hydrologic conditions to identify areas susceptible to arsenic contamination. In this study, batch- and column-leaching tests and sequential extraction procedures were used to examine arsenic leaching processes in detail. The results showed that most arsenic-loaded sediments accumulated in the vicinity of a reservoir inlet, and arsenic in reservoir beds have a higher leaching potential than those from agricultural land and river beds. Arsenic deposited at the bottom of reservoirs had higher mobility than that in the other soils, and arsenic leaching was closely associated with the acidity of water. In addition, arsenic leaching was found to be responsive to seasons (wet or dry) as its mobilization is controlled by organic compounds that vary over time. The results suggested that temporal variations in the hydrochemical composition of reservoir water should be considered when defining a management plan for reservoir water quality.

3D printing technology has brought about a paradigm shift in the delivery of clinical care in medicine and dentistry. There are several different 3D printing technologies, which, along with different printable materials with unique biomechanical properties, allows for a wide range of applications for 3D printing in dentistry. The clinical use of 3D printing has created versatile applications which streamline our digital workflow. Technological advancements have also paved the way for the integration of new dental materials in dentistry. This paper provides an overview of the mechanisms of 3D printing, the dental materials relevant to each mechanism and the possible applications of these materials within different areas of dentistry. Understanding the existing spectrum of 3D printing applications in dentistry will serve to further expand its use in the dental field.

The current study is to examine the disparities in physical activity (PA), sedentary behavior (SB), and stress levels in Korean adolescents concerning changes in their perception of family socio-economic status (SES) during COVID-19. Among a total of 6144 Korean adolescents aged 12 to 18, the participants were categorized into two groups based on their responses regarding changes in their family SES during COVID-19: Lower SES (n = 3072) and Non-changed SES (n = 3072), with matching in terms of age, gender, and BMI. All variables were assessed using the 16th year (2020) of the Korean Youth Risk Behavior Survey. Statistical analyses were conducted using SPSS 26.0 version, employing independent t-tests to examine anthropometrics’ differences and multinominal logistic regression to predict the impact of perception of family SES on PA, SB, and stress while comparing the two groups. The significance level was set at α = 0.05. Adolescents in the Lower SES group were less likely to engage in vigorous-intensity PA (VPA) and muscular strength activities compared to those in the Non-changed SES group (p < 0.001) and were 2.3 times more likely to experience a very-severe stress level than the Non-changed SES group (p < 0.001). These results shed light on the importance of promoting VPA and muscular strength activities in adolescents for their physical and mental well-being, particularly during potential future pandemics. Understanding the impact of perceived SES changes on health behaviors can inform targeted interventions and support strategies to improve the health outcomes of adolescents during challenging times.

Alveolar soft part sarcoma (ASPS) is a rare mesenchymal neoplasm. It affects young adults more and occurs more frequently in the extremities. ASPS is exceedingly rare in the nasal cavity. We report a case of ASPS in the nasal cavity of a 17-year-old female. Its most striking features included organoid and pseudoalveolar arrangement of tumor cells, which were large and polygonal, with vesicular nuclei and abundant eosinophilic cytoplasm rich in granules. There were PAS-positive, diastase-resistant crystalline rods within the cytoplasm. Our case displayed inapparent pseudoalveolar growth pattern and frank pleomorphism. The diagnosis of ASPS, which presents uncommon morphologic findings in unusual sites, is challenging. Recognition of ASPS is greatly assisted by attention to its characteristic cytological features, including intracytoplasmic crystals and immunohistochemistry showing absence of skeletal muscle, epithelial, and neuroendocrine markers.

This study entailed the design and analysis of a 400 m-class underwater glider operated by a bladder-type buoyancy engine. The underwater glider was designed for high-speed movement with a maximum velocity of 2 knots. The shape of the hull was designed to reduce water resistance using the Myring hull profile equation. The reliability was verified by performing simulations using resistance coefficients. The relationship between the control value of the ballast discharged from the buoyancy engine and the glider's speed according to the path angle was analyzed. Further, the relationship between the optimal glide angle and the design control value of the ballast was derived, and the optimal glider speed was estimated accordingly. Based on the analysis results, a bladder-type buoyancy engine was developed, and the maximum speed of the tested underwater glider was measured via sea trials.

This study investigates the impact of thin flame combustor design on hydrogen flame characteristics and combustion performance through numerical simulations. Variations in flame shape and combustibility between 100% methane and 100% hydrogen combustion are analyzed. Three combustor header shapes (flat, concave, and convex) are modeled to assess their influence on flame behavior. Results show distinct flow patterns, with concave headers promoting strong central flows and convex headers dispersing the flow outward. Temperature field analysis indicates that hydrogen flames have higher temperatures and shorter quenching distances compared to methane flames. A comparative analysis of combustion products is conducted to evaluate combustion performance and NOx emissions. Consequently, the concave header has high combustibility and increases temperatures and NOx fraction in hydrogen combustion.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

Large epidemiological studies show U-shaped relationships between high-density lipoprotein cholesterol (HDL-C) levels and all-cause mortality in individuals without atherosclerotic cardiovascular diseases (ASCVD). Association in those with ASCVD by sex is unclear. We examined the association between HDL-C levels and 10-year all-cause mortality in subjects (≥40 years of age) with ASCVD using the 2010 National Health Insurance Service and the National Death Registry of Korea. We categorized HDL-C levels into three groups (low: <40 mg/dL for males, <50 mg/dL for females; high: 40-90 mg/dL for males, 50-90 mg/dL for females; extremely high: >90 mg/dL) and 10 mg/dL intervals. We conducted a sex-stratified and adjusted Cox proportional hazards analysis. Out of 1,711,548 individuals (54% female, mean age 61.4 years), 10-year mortality was observed in 218,252 (12.8%). Males had a higher mortality rate than females (16.2% vs 9.8%; P<0.001). When adjusting for age, body mass index, LDL-cholesterol, triglycerides, hypertension, diabetes, smoking, and alcohol consumption, the low and extremely high HDL-C groups had significantly higher hazard ratios for 10-year mortality compared to the high HDL-C group in males [1.183 (1.166-1.199), 1.359 (1.288-1.434)] and in females [1.153 (1.138-1.169), 1.095 (1.029-1.167)]. The frequency distribution bars for the 10-year mortality rate showed sex-specific nadirs of 50-59 mg/dL in males and 70-79 mg/dL in females. In this ASCVD cohort, the extremely high HDL-C (>90 mg/dL) group had 35.9% and 9.5% higher 10-year mortality risk than the high HDL-C group for males and females, respectively. There was a slightly U-shaped relationship between baseline HDL-C levels and 10-year mortality rate, with earlier inflection in males than in females.

The work proposes a backtesting analysis in comparison between the Lee-Carter and the Cairns-Blake-Dowd mortality models, employing Italian data. The mortality data come from the Italian National Statistics Institute (ISTAT) database and span the period 1975-2014, over which we computed back-projections evaluating the performances of the models in comparisons with real data. We propose three different backtest approaches, evaluating the goodness of short-run forecast versus medium-length ones. We find that both models were not able to capture the improving shock on the mortality observed for the male population on the analyzed period. Moreover, the results suggest that CBD forecast are reliable prevalently for ages above 75, and that LC forecast are basically more accurate for this data.

Stereotactic radiosurgery (SRS) is considered the initial treatment for lung cancer patients with small-sized and limited number of brain metastases. The objective of this study was to assess clinical outcomes of SRS treatment using CyberKnife (CK) for recursive partitioning analysis (RPA) class II/III patients with one to three brain metastases from lung cancer and identify which patients in the high RPA class could benefit from SRS. A total of 48 lung cancer patients who received CK-based SRS for their metastatic brain lesions from 2010 to 2017 were retrospectively analyzed. Radiographic response was evaluated during follow-up period. Overall survival (OS) and intracranial progression-free survival (IPFS) were calculated and prognostic variables associated with OS and IPFS were evaluated. Median follow-up time was 6.6 months. Local control rates at 6 months and 1-year following SRS were 98% and 92%, respectively. The median OS of all patients was 8 months. One-year and 2-year OS rates were 40.8% and 20.9%, respectively. In multivariate analysis, uncontrolled primary disease (p = 0.008) and ECOG performance status of 2 or 3 (p = 0.001) were independent prognostic factors for inferior OS. These two factors were also significantly associated with inferior IPFS. In subgroup analysis according to RPA class, primary disease status was the only prognostic factor, showing statistically significant OS differences in both RPA class II and III (controlled vs. uncontrolled: 41.1 vs. 12.3 months in RPA class II, p = 0.031; 26.9 vs. 4.1 months in RPA class III, p = 0.011). Our results indicated that SRS could be an effective treatment option for RPA class II/III patients with brain metastases from lung cancer in the modern treatment era. SRS might be particularly considered for patients with controlled primary disease.

This study examines whether gas is emitted from the materials used in the fabrication of metal vacuum panels or not and if emitted, their degree as time goes by. As experimental materials, metal sheets, foamed concrete as a core material, and polymer materials as a sealing material between metal sheets were selected. Experiments on the type and the degree of bending of metal materials showed that aluminum’s vacuum reaching time of 0.001 torr was at least 40 sec to 90 sec in its flat plate, but its vacuum reaching time increased from 3 times to 4.5 times in case of 90 ° and 135 ° bending state. For this reason, it is judged that stainless steel or steel material is suitable because aluminum is inadequate in terms of processability at the time of fabricating the metal vacuum panel. Also, vacuum arrival times and weight changes with increasing foam content of inorganic foamed concrete increased from 22,000 sec to 42,000 sec with increasing foaming rate and also, the weight change increased from 1.7% to 8%. Also, the experimental results on the type of honeycomb materials, the PE (polyethylene) with a vacuum reaching time of 30,000 sec and with a weight change of 0.5% and the PTFE (Poly-tetrafluoro ethylene) with a vacuum reaching time of 29,000 sec and with a weight change of 2.2% showed the optimum value.

Background: The scaffold protein tyrosine kinase substrate 4 (TKS4) undergoes tyrosine phos-phorylation by the epidermal growth factor receptor (EGFR) pathway via Src kinase. The TKS4 deficiency in humans is responsible for the manifestation of a genetic disorder known as Frank-Ter Haar syndrome (FTHS). Based on our earlier investigation, the absence of TKS4 triggers migration, invasion, and epithelial-mesenchymal transition (EMT)-like phenomena while concurrently suppressing cell proliferation in HCT116 colorectal carcinoma cells. This indicates that TKS4 may play a unique role in the progression of cancer. In this study, we demonstrated that the enhancer of zeste homolog 2 (EZH2) and the histone methyltransferase of polycomb repressive complex 2 (PRC2) are involved in the migration, invasion, and EMT-like changes in TKS4-deficient cells (KO). EZH2 is responsible for the maintenance of the trimethylated lysine 27 on histone H3 (H3K27me3). Methods: We performed the transcriptome sequencing, chromatin immunoprecipitation, protein and RNA quantitative studies, cell mobility, invasion, and proliferation studies combined with/without EZH2 activity inhibitor 3-deazanoplanocine (DZNep) Results: We detected an elevation of global H3K27me3 levels in the TKS4 KO cells, which could be reduced with treatment with DZNep, an EZH2 inhibitor. Inhibition of EZH2 activity reversed the phenotypic effects of the knockout of TKS4, reducing the migration speed and wound healing capacity of the cells as well as decreasing the invasion capacity, while the decrease in cell prolif-eration became stronger. In addition, inhibition of EZH2 activity also reversed most epithelial and mesenchymal markers. We investigated the wider impact of TKS4 deletion on the gene expression profile of colorectal cancer cells using transcriptome sequencing of wild-type and TKS4 knockout cells, particularly before and after treatment with DZNep. Additionally, we observed changes in the expression of several protein-coding genes and long non-coding RNAs that showed a recovery in expression levels following EZH2 inhibition. Conclusions: Our results indicate that the removal of TKS4 causes a notable disruption in the gene expression pattern, leading to the disruption of several signal transduction pathways. Inhibiting the activity of EZH2 can restore most of these transcriptomics and phenotypic effects.

Here, we report a simple and effective method for separation of gram-negative bacteria using aptamer-modified microbeads and acoustophoresis. As acoustophoresis allows for simultaneous washing and size-dependent separation in continuous flow mode, we efficiently obtained gram-negative bacteria that showed high affinity without any additional washing steps. The proposed device has a simple and efficient channel design, utilizing a long, square-shaped microchannel that shows excellent separation performance in terms of the purity, recovery, and concentration factor. Microbeads (10 µm) coated with the GN6 aptamer can specifically bind gram-negative bacteria. Using acoustophoresis, gram-negative bacteria-bound microbeads and other unbound/contaminants can be separated by size with high purity and recovery. The device demonstrated excellent separation performance, with high recovery (up to 98%), high purity (up to 99%), and a high volume rate (500 µL/min), and a concentration factor of up to 20×. The acoustophoresis microfluidic device also showed binding affinity to multiple strains of gram-negative bacteria, but not to gram-positive bacteria. This study presents a new paradigm for early diagnosis of bacterial infectious diseases. In addition to detecting living bacteria or bacteria-derived biomarkers, this protocol can be extended to monitoring the contamination of water resources, and may aid quick responses to bioterrorism and pathogenic bacterial infections.

This retrospective study aimed to evaluate the impact of radiation dose on the outcomes of stereotactic radiosurgery (SRS) for benign meningiomas and determine an optimal dosing strategy for balancing tumor control and treatment-related toxicity. Clinical data of 147 patients with 164 lesions treated between 2014 and 2022 were reviewed. Primary outcomes included progression-free survival (PFS), local control rate (LCR), and radiation-induced toxicity, with secondary outcomes focusing on LCR and radiation-induced peritumoral edema (PTE) in two dose groups (≥14 Gy and &lt;14 Gy). Results revealed a median follow-up duration of 47 months, with 1-year, 2-year, and 5-year PFS rates of 99.3%, 96.7%, and 93.8% respectively, and an overall LCR of 95.1%. Radiation-induced toxicity was observed in 24.5% of patients, primarily presenting mild symptoms. Notably, no significant difference in LCR was found between the two dose groups (P = 0.628), while Group 2 (&lt;14 Gy) exhibited significantly lower PTE (P = 0.039). The study concludes that SRS with a radiation dose &lt;14 Gy demonstrates comparable tumor control with reduced toxicity, advocating for consideration of such dosing to achieve a balance between therapeutic efficacy and safety.

This paper presents a study aimed at enhancing the performance of quantum dot light-emitting didoes (QLEDs) by employing a solution-processed molybdenum oxide (MoO3) nanoparticle (NP) as a hole injection layer (HIL). The study investigates the impact of varying the concentrations of the MoO3 NP layer on device characteristics and explores the underlying mechanisms responsible for the observed enhancements. Experimental techniques such as an X-ray diffraction and field-emission transmission electron microscopy were employed to confirm the formation of MoO3 NPs during the synthesis process. Ultraviolet photoelectron spectroscopy is employed to analyze the electron structure of the QLEDs. The QLED with an 8 mg/mL concentration of MoO3 nanoparticles achieves remarkable improvements in device performance, with a maximum luminance of 69,240.7 cd/cm2, maximum current efficiency of 56.0 cd/A, and maximum external quantum efficiency (EQE) of 13.2%. The obtained results signify a notable progress in comparison to QLED without HIL and those utilizing the widely used poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) HIL. They exhibit a remarkable enhancement of 59.5% and 26.4% in maximum current efficiency, respectively, as well as a significant improvement of 42.7% and 20.0% in maximum EQE, respectively. This study opens up new possibilities for the selection of HIL and the fabrication of solution-processed QLEDs, contributing to the potential commercialization of these devices in the future.

Robots for communication are developed extensively with emphasis on sympathy. This study deals with the growth of character and the control of its operation accordingly. The child has time to be alone with the nature of his/her robot friend. The child can interact with other people's emotional expressions through a robot. Step by step, the robot character will grow as the child grows. Through design studies, qualitative processes such as {customer experience audit, eye tracking, mental model diagrams, semantic differences} have been executed for the results. The participatory behavior research approach through user travel is mapped from the user's lead to the evidence-based design. This research considers how the synthetic characteristics can be applied to the physical growth of robot toys through the product design process. With the development of robot toy "Buddy", we tried making two variations on the robot to achieve recognizable growth. (1) A one-dimensional height scaling and (2) facial expression including the distance between two eyes on the screen. Observations represented children's reactions when "Buddy" was released to with the children. As an independent synthetic character, the robot was recognized by children who had the designed function. Robots for training may require more experimentation.

The molecular dynamics simulation has been used to investigate the structural and transport properties of (Ba_0.5-xSr_x)La_0.5InO_3-δ (x=0, 0.1, 0.2) oxygen-ion conductor. The previous studies reported that the ionic conductivity of Ba-doped LaInO3 decreases because Ba dopant forms narrow oxygen path in the lattice, which could hinder the diffusion of oxygen ion. In this study, we reveal the mechanism to improve the ionic conductivity by Ba and Sr co-doping on La site in LaInO3 perovskite oxide. The results show that the ionic conductivity of (Ba_0.5-xSr_x)La_0.5InO_3-δ increases with increasing numbers of Sr ions, which oxygen diffusion paths including Sr ion have larger critical radius than Ba ions. The RDF calculations showed the heights of peak in composition including Sr ions is lower and broaden, so oxygen ions moved easily into other oxygen sites.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

Depressive disorder in childhood and adolescence is a highly prevalent mood disorder that tends to recur throughout life. Untreated mood disorders can adversely impact a patient's quality of life and cause socioeconomic loss. Thus, an accurate diagnosis and appropriate treatment is crucial. However, until now, diagnoses and treatments are conducted according to clinical symptoms. Objective and biological validation are lacking. This may result in a poor outcome for patients with depressive disorder. Research has been conducted to identify the biomarkers that are related to depressive disorder. Cumulative evidence has revealed that certain immunologic biomarkers in-cluding brain-derived neurotrophic factor (BDNF) and cytokines, gastrointestinal biomarkers, hormones, oxidative stress, and certain hypothalamus-pituitary axis biomarkers are associated with depressive disorder. This article reviews the biomarkers related to the diagnosis and treatment of pediatric depressive disorders. To date, clinical biomarker tests are not yet available for diagnosis or for the prediction of treatment prognosis. However, cytokines such as Interleukin-2, interfer-on-gamma, tumor necrosis factor-alpha, and BDNF have shown significant results in previous studies of pediatric depressive disorder. These biomarkers have the potential to be used for diagnosis, prognostic assessment, and group screening for those at high risk.

The human oral microbiome refers to an ecological community of symbiotic and pathogenic microorganisms found in the oral cavity. The oral cavity is a suitable environment that provides various kinds of biological niches such as teeth, tongue, and oral mucosa. The oral cavity is the gateway between the external environment and the human body, maintaining oral homeostasis, protecting the mouth, and preventing disease. On the flip side, the oral microbiome plays an important role in triggering, development, and progression of oral and systemic diseases. Currently, disease diagnosis through the analysis of the human oral microbiome has been realized with the recent development of innovative detection technology, and is overwhelmingly promising compared to the previous era. It has been found that patients with oral diseases and systemic diseases have variations in the oral microbiome compared to normal subjects. This narrative review provides insight into the pathophysiological role that oral microbiome plays in influencing oral and systemic diseases, and updates the knowledge related to the oral microbiome over the past 30 years. A wide range of updates was provided with the latest knowledge of the oral microbiome to help researchers and clinicians in both academic and clinical aspects. The microbial community information can be utilized in non-invasive diagnosis and help develop a new paradigm in precision medicine, which will benefit human health in the era of post-metagenomics.

Cisplatin is a widely used anticancer drug for treating solid tumors, but it is associated with severe side effects, including nephrotoxicity. Various studies have suggested that the nephrotoxicity of cisplatin could be overcome; nonetheless, an effective adjuvant drug has not yet been established. Oleanolic acid acetate (OAA), a triterpenoid isolated from Vigna angularis, is commonly used to treat inflammatory and allergic diseases. This study aimed to investigate the protective effects of OAA against cisplatin-induced apoptosis and necroptosis using TCMK-1 cells and a mouse model. In cisplatin-treated TCMK-1 cells, OAA treatment significantly reduced Bax and cleaved-caspase3 expression, whereas increased Bcl-2 expression. Moreover, in cisplatin-induced kidney injury mouse model, OAA treatment alleviated weight loss in the body and major organs and also relieved cisplatin-induced nephrotoxicity symptoms. RNA sequencing analysis of kidney tissues identified lipocalin-2 as the most upregulated gene by cisplatin. Additionally, necroptosis-related genes such as receptor interacting protein kinase (RIPK) and mixed lineage kinase domain like (MLKL) were identified. In vitro study, the phosphorylation of RIPKs and MLKL was reduced by OAA pretreatment in both cisplatin-treated cells and cells boosted by co-treatment with z-VAD-FMK. In conclusion, OAA could protect the kidney from cisplatin-induced nephrotoxicity and may serve as an anticancer adjuvant.

The dynamic and surface manipulation of the M13 bacteriophage meeting application demands enable a pathway to design efficient applications with high selectivity and responsivity rate. Herein, we report the role of the M13 bacteriophage thin film layer deposited on an optical nanostructure involving gold nanoparticles/SiO2/Si and its influence on optical and geometrical properties. The thickness of the M13 phage layer was either controlled by varying the concentration or humidity exposure levels, and optical studies were conducted. We designed a standard and dynamic model based upon three-dimensional finite-difference time-domain (3D FDTD) simulations distinguishing the necessity of each model under variable conditions. As seen from the experiments, the origin of respective peak wavelength positions is addressed in detail with the help of simulations. The importance of the dynamic model was noted when humidity-based experiments were conducted. Inexpensive, multi-wavelength optical characteristics from a single structure, reproducibility, and reversible properties are significant advantages of involving M13 bacteriophage. We believe this work will provide fundamental insight into understanding and interpreting the geometrical and optical properties of the nanostructures involving M13 bacteriophage.

Eight compounds were isolated from the roots of Glycyrrhiza uralensis and tested for cholinesterase (ChE) and monoamine oxidase (MAO) inhibitory activities. Glycyrol (GC) effectively inhibited butyrylcholinesterase (BChE) and acetylcholinesterase (AChE) with IC50 values of 7.22 and 14.77 µM, respectively, and also moderately inhibited MAO-B (29.48 µM). Six of the other seven compounds only weakly inhibited AChE and BChE, whereas liquiritin apioside moderately inhibited AChE (IC50 = 36.68 µM). Liquiritigenin (LG) potently inhibited MAO-B (IC50 = 0.098 µM) and MAO-A (IC50 = 0.27 µM), and liquiritin, a glycoside of LG, weakly inhibited MAO-B (&gt; 40 µM). GC was a reversible, noncompetitive inhibitor of BChE with a Ki value of 4.47 µM, and LG was a reversible competitive inhibitor of MAO-B with a Ki value of 0.024 µM. Docking simulations showed that the binding affinity of GC for BChE (-7.8 kcal/mol) was greater than its affinity for AChE (-7.1 kcal/mol), and suggested that GC interacted with BChE at Thr284 and Val288 by hydrogen bonds (distances: 2.42 and 1.92 Å, respectively) beyond the ligand binding site of BChE, but that GC did not form hydrogen bond with AChE. The binding affinity of LG for MAO-B (-8.8 kcal/mol) was greater than its affinity for MAO-A (-7.9 kcal/mol). These findings suggest GC and LG should be considered promising compounds for the treatment of Alzheimer’s disease with multi-targeting activities.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

Preproenkephalin (PPE) is a precursor molecule for multiple endogenous opioid peptides Leu-enkephalin (ENK) and Met-ENK, which are involved in a wide variety of modulatory functions in the nervous system. Despite the functional importance of ENK in the brain, the effect of brain-derived factor(s) on PPE expression is unknown. We report the dual effect of neural epidermal growth factor (EGF)-like-like 2 (NELL2) on PPE gene expression. In cultured NIH3T3 cells, transfection of NELL2 expression vectors induced an inhibition of PPE transcription intracellularly, in parallel with downregulation of protein kinase C signaling pathways and extracellular signal-regulated kinase. Interestingly, these phenomena were reversed when synthetic NELL2 was administered extracellularly. The in vivo disruption of NELL2 synthesis resulted in an increase in PPE mRNA level in the rat brain, suggesting that the inhibitory action of intracellular NELL2 predominates the activation effect of extracellular NELL2 on PPE gene expression in the brain. Biochemical and molecular studies with mutant NELL2 structures further demonstrated the critical role of EGF-like repeat domains in NELL2 for regulation of PPE transcription. These are the first results to reveal the spatio-specific role of NELL2 in the homeostatic regulation of PPE gene expression.

Additive manufactured interlocking structures often face challenges in achieving suitable joinability due to thermal deformation. This issue becomes particularly interesting when fabricating structures that require high density but not fully connected layers, such as soft-magnetic materials. This study focuses on systematical investigation of the deformation as a function of finger thickness and building direction in model interlocking structure. In the perpendicular direction to the build plate, the distortions of joint part were significantly reduced due to lower thermal stress. In addition, the effect of laser power and scan speed on interlocking structure are systematically discussed. Additionally, through stress and thermal simulations of additive manufacturing process, it was confirmed that the compensated model can enhance the joinability of interlocking structures. These findings contribute to the development of optimal design for additive manufactured parts of soft magnetic materials such as stators in electric motor components, which needs insulations and density.

Alzheimer's disease (AD) is a neurodegenerative olfactory disorder affecting millions of people worldwide. Alterations in the hexosamine or glucose-related pathways have been described through AD progression. Specifically, an alteration in glucosamine 6 phosphate isomerase 2 (GNPDA2) protein levels has been observed in olfactory areas from AD subjects. However, the biological role of GNPDA2 in neurodegeneration remains unknown. Using mass-spectrometry, multiple GNPDA2 interactors were identified in human nasal epithelial cells (NECs) mainly involved in intraciliary transport. Moreover, GNPDA2 overexpression induced an increment in NEC proliferation rates, accompanied by transcriptomic alterations in Type II interferon signalling or cellular stress responses. In contrast, the presence of beta-amyloid or mutated Tau-P301L in GNPDA2-overexpressing NECs induced a slow-down in the proliferative capacity in parallel with a disruption in protein processing. The proteomic characterization of Tau-P301L transgenic zebrafish embryos demonstrated that GNPDA2 overexpression interfered with collagen biosynthesis and RNA/protein processing, without inducing additional changes in axonal outgrowth defects nor neuronal cell death. In humans, a significant increase in serum GNPDA2 levels was observed across multiple neurological proteinopathies (AD, Lewy body dementia, progressive supranuclear palsy, mixed-dementia, and amyotrophic lateral sclerosis) (n=187). These data shed new light on GNPDA2-dependent mechanisms associated to the neurodegenerative process beyond the hexosamine route.

Honey bee (Apis mellifera) health is crucial for honey bee products, and effective pollination and is closely associated with gut bacteria. Various factors such as reduced habitat, temperature, disease, and diet affect the health of honey bees, by disturbing the homeostasis of the gut microbiota. In this study, high-throughput 16S rRNA gene sequencing was used to analyze the gut microbiota of Apis mellifera subjected to seven different diets. The identified microbiota in the Apis mellifera gut from all the diets consisted of Lactobacillus (62%), followed by Rhizobiaceae (21%), Snodgrassella (4%), and Erwiniaceae (4%) among other 33 genera. Based on diet types, Lactobacillus a lactic acid bacteria (LAB), dominates the microbiota with the highest relative abundance in AIGT+SAC (91%), AIGT+Soytide (88%), and AIGT+Apple juice (69%) diet groups. Bifidobacterium and Commensalibacter appeared as the second most abundant genera in AIGT+SAC and AIGT+Soytide diet groups, respectively. These bacteria are important markers for honey bee health. Considering the importance of these diets in shaping their host microbiome into a healthy status. Individual honey bee health (IHH) was observed to validate the quality and correlation between the microbiota and honey bee health. The results were consistent, indicating that Apis mellifera fed on AIGT+Soytide and AIGT+SAC diet showed the highest health expression level of vitellogenin. The group with 60%Syrup possessing Rhizobiaceae as the dominant taxa showed poor health status. This finding paved the way for establishing a link between gut microbiota and IHH under different diets.

The effectiveness of Fuzzy Inference Systems (FISs) in manipulating uncertainty and nonlinearity makes them a subject of significant interest for decision-making in embedded systems. Accordingly, optimizing FIS hardware improves its performance, efficiency, and capabilities, leading to a better user experience, increased productivity, and cost savings. To be compatible with the limited power budget in most embedded systems, this paper presents a framework to realize ultra-low power FIS hardware. It supports optimizations for both conventional arithmetic as well as MSDF-computing to be highly consistent with MSDF-based sensors. In MSDF-computing FIS all the processes of fuzzification, inference, and defuzzification are done on serially coming data bits. To demonstrate the efficiency of the proposed framework, we utilized Matlab, Chisel3, and Vivado to implement it from high-level descriptions of FIS to hardware synthesis. We also developed a Scala library in Chisel3 to establish a connection between these tools, bridging the gap, and facilitating design space exploration at the arithmetic level. Furthermore, we realized an FIS for the navigation of autonomous mobile robots in unknown environments. Synthesis results show the superiority of the output of our suggested design framework in terms of resource usage as well as power and energy consumption compared to the Matlab HDL code generator output.