The Gurney flap (GF) is a miniature lift-enhancement device and is usually mounted at the trailing edge of an airfoil. The GF and has been successfully applied to isolated airfoils, multi-element airfoils, and aircraft wings as well as helicopter rotor due to its attractive features of simplicity, cost-effective and separation control. The GF also has aroused the attention of researchers in the turbomachinery industry. However, limited studies are currently available on the application of a GF to an axial fan.Hence, in this paper, we conduct a wind tunnel and computational fluid dynamic (CFD) investigation on an axial fan profiled with a NACA 65-(12)10 airfoil to evaluate the effect of the GF on the performance of the fan. We also present the detailed flow features of the fan with and without the GF after validating the simulation results with the experimental results. The experimental results show that as the GF is installed higher on the fan blade, it can produce a higher total pressure rise accompanied with a greater loss of efficiency. The installation of the GF also enlarges the work capacity of the fan. Detailed flow field analysis, including the surface pressure distribution, vorticity distribution at the trailing edge and streamline distribution of the fan, is carried out to understand the mechanisms of the effect of the GF on the performance of the fan.

Excessive vibration of temporary grandstand owing to crowd has lateral rhythmic motions can cause human in panic, which attracted increasing attention in recent years. This paper focuses on experiments that a temporary grandstand occupied 20 participants is oscillated by a shaking table with a series of random waves and induced by crowd with rhythmic swaying motions at lateral direction, respectively. And then a series of vibration perception questionnaires about crowd reaction are obtained. Evaluation of annoying level derives in concept of degree of membership and annoying rate method is proposed, then the human health risk of vibration serviceability of temporary grandstand is assessed with acceleration vibration dose value(VDV). From these results it is clear that standing crowd is more tolerant to vibration than seated crowd. The measured vibrations generated by crowd activities on temporary grandstand can cause panic in crowd. New relationship between the annoyance rate and structural acceleration VDV at logarithmic coordinate is proposed. The findings of this study can be utilized to manage the vibration of temporary grandstand and assess the human health risk.

In order to alleviate the conflict between populations and land-resource, Tianjin has adopted multi-phase reclamation projects to formed large-scale artificial reclamation land. However, the reclamation areas are susceptible to subsidence, which demonstrate a serious threat to infrastructure and people’s lives and property. The SBAS-InSAR was used to acquired surface deformation of Tianjin Binhai New Area from January 2017 year to December 2022 year, analyzed in depth the response relationship between land subsidence and reclamation projects time as well as the land use type. The results show that the Lingang Industrial Zone was the earliest to be reclaimed, with extensive reclamation completed by 2016 year, while Nangang Industrial Zone and Hangu Port started reclamation projects in 2009 year, some areas are still currently under construction. There is a strong correlation between surface deformation and reclamation time, the severe land subsidence occurred over newly reclaimed areas. Surface deformation gradually intensifies from west to east, the maximum surface settlement in Nangang Industrial Zone, Lingang Industrial Zone from the west to the east has changed from -50 mm to -890 mm,45 mm to -580 mm, respectively, reclamation area of Hangu Port with maximum surface deformation is -250 mm. Significant differences deformation among different land use types, which reclamation projects completed in the same time. Subsidence is positively correlated with surface load, in areas with higher surface loads, the surface settlement is also severer,the average surface settlement for the heavy shipyard, 67 grain storage tanks, 27 grain storage tanks, road, and bare land are -201 mm, -166 mm, -107 mm, -64 mm, and -43 mm, respectively. This study reveals significant differences of surface deformation in the reclamation completed at different times and the load is the main driving factor of settlement difference in the reclamation land completed at the same time. Which has important guiding significance for preventing and controlling geological disasters in the reclamation area and later development planning.

In this work, we try to find a way to describe the physical law of micro-world under the frame of a space-time theory. By introducing the scalar fields $\mathcal{D}\left( x\right)$ and $\zeta\left( x\right) $, we rewrite the action of conventional field theory and the Lagrangian describing the motion of the particle, where a modified space-time relation is obtained. To test the correctness of this attempt, we demonstrate the Klein-Gordon equation by the Hamilton-Jacobi method in four dimensional form and present a time delay for the ground state of hydrogen atom.

With the increased use of laterite nickel ore, the impact of high Al2O3 slag on blast furnace smelting has gradually increased. In this paper, the effects of slag basicity and Al2O3 content on slag viscosity and enthalpy change under constant temperature conditions was investigated. The changes in slag structure were analyzed by activation energy and Fourier Transform Infrared (FT-IR) spectroscopy. The relationship between slag components and slag temperature and viscosity when slag heat is reduced was investigated. The results showed that the viscosity first slightly decreased and then significantly increased with increasing basicity at constant temperature. With the addition of Al2O3 content, the viscosity of the slag increases. The activation energy increases with increasing slag basicity and Al2O3. With increasing basicity, the [SiO4]4- tetrahedral unit trough depth becomes shallow, the [AlO4]5- asymmetric stretching band migrates to lower wave numbers, and the slag structure depolymerizes. With the increase of Al2O3 content, the trough of [SiO4]4- tetrahedra deepens and the center of the symmetric stretching band moves to a higher wave number. The [AlO4]5- asymmetric stretching band becomes obvious, indicating the complexity of the slag structure. When the heat decreases, the slag temperature increases as the basicity increases, and the slag thermal stability is better at the basicity of 0.95-1.05. As the Al2O3 content increases, the thermal stability of the slag becomes worse.

Agricultural activities are the second largest source of greenhouse gas emissions, and carbon emissions from agricultural land use (CEALU) have become a hot issue across the world. However, few scholars explored the impact of agricultural land policies on carbon emissions, such as the High-standard farmland construction(HSFC) in China.Thus，by relying on provincial panel data for China for the period 2005-2017, the effect of the high-standard basic farmland construction policy on carbon emissions from agricultural land use per unit area and its regional differences were quantitatively analyzed using the difference-in-difference (DID) model. The results showed that: 1) China's CEALU per unit area presented a fluctuating upward trend during the period 2005-2017, from 392.58 kg/ha to 457.72 kg/ha, with an average annual growth rate of 1.31%. 2) The high-standard farmland construction(HSFC) policy produced a significant carbon emission reduction effect in agricultural land use, and reduced the CEALU per unit area by 10.80% on average. With the promotion of this policy, its carbon emission reduction effect in agricultural land use presented an overall increasing trend. 3) The carbon emission reduction effect of the high-standard farmland construction policy in agricultural land use was significant in central China, but non-significant in eastern China and western China.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

Although Darwin‘s evolutionary mutation theory has been widely accepted, many endeavors have been tried to challenge it. With more and more observation of successful hybridization and hybrids, the sexual isolation between species has become vague. The mechanism of evolution has been expanded from the classical model of evolution to multiple routes of speciation. Furthermore, a fundamental crossbreeding theory has been raised and proved by two lines of evidences: paleopolyploidy and fan-shaped spectrum of species. Ancient genome duplications are widespread throughout eukaryotic lineages, particularly in plants. The genome polyploidization, especially in the somatic cell hybridization, can break through the sexual incompatibility between diploid counterparts to hybridize and produce new species. By comparing characteristics, all species in every taxon, both in the extinct fossil and extant organisms, can be arranged into fan-shaped spectrum according to their similarity: left primitive type-middle advanced type-right primitive type. The species are primitive at the two ends and advanced at the middle. The primitive two species always resemble two types of more primitive species that can be confirmed as their ancestors respectively, and the middle species is half similar to the two ancestors respectively. These suggest that the species in the spectrum come from two different ancestors by crossbreeding and gene combination. As a sum, advanced species originated from crossbreeding of two primitive ancestors, by major method of polyploidization, and proved by results of fan-shaped spectrum of species. Then, sex is the cause, force and opportunity for evolution.

Monitoring is an important component of pest management, to prevent or mitigate outbreaks of native pests, and to check for quarantine organisms. Surveys often rely on trapping, especially when the target species respond to semiochemicals. Many traps are available for this purpose, but they are bulky in most cases, which raises transportation and deployment issues, and they are expensive, which limits the size and accuracy of any network. To overpass these difficulties, entomologists have used recycled material, such as modified plastic bottles, producing cheap and reliable traps but at the cost of recurrent handywork, not necessarily possible for all end-users (e.g., for national plant protection organizations). These bottle-traps have allowed very large surveys which would have been impossible with standard commercial traps, and we illustrate this approach with a few examples. Here we present, under a Creative Commons BY-SA License, the blueprint of a fan-trap, a foldable model, laser-cut from a sheet of polypropylene, that can rapidly be produced in large numbers, and could be transported and deployed in the field with very little efforts. Our first field comparisons show that fan-traps are as efficient as bottle-traps, and we describe two cases where they are being used for monitoring.

In thermal power plants equipped with air-cooled condensers, axial cooling fans operate under the influence of ambient flow fields. Under inlet cross-flow conditions, the resultant asymmetric flow field is known to introduce additional harmonic forces to the fan blades. This effect has previously been studied only numerically or using blade mounted strain gauges. For this study, Laser Scanning Vibrometry was used to assess fan blade vibration under inlet cross-flow conditions in an adapted fan test rig inside a wind tunnel test section. Two co-rotating laser beams scanned a low pressure axial fan, resulting in spectral, phase resolved surface vibration patterns of the fan blades. Two distinct operating points were examined, with and without inlet cross-flow influence. While almost identical fan vibration patterns were found for both reference operating points, overall blade vibration increased by 100% at low fan flow rate due to cross-flow, and by 20% at high fan flow rate. While numerically predicted natural frequency modes could be confirmed from experimental data as minor peaks in the vibration amplitude spectrum, they were not excited significantly by cross-flow. Instead, primarily higher rotation rate harmonics were amplified, i.a. a synchronous blade tip flapping was strongly excited at the blade pass frequency.

Because of the widespread use of bisphenol analogues (BPs) as the alternatives to bisphenol A (BPA), they have attracted considerable attention for health risk in aquatic ecosystems. The occurrence and distribution of six BPs were researched in soluble phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. Except for bisphenol Z, all BPs were detected in the two or three phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the soluble phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the soluble and colloidal phases, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude higher than SPM, suggesting that colloids have an obvious impact on regulating BPs’ environmental behaviors. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

We successfully designed an optimized plenum fan with a three-dimensional, smooth, curved blade. The optimized model revealed that the static pressure in the channel had been increased uniformly and stably, and the flow separation at the leading edge was significantly reduced. To conclude, the three-dimensional blade stabilized the fluid flow, and the flow friction was reduced by suppressing the flow separation as much as possible so that both the static pressure and the static efficiency were clearly improved in comparison with those of the original model. The static efficiency, as a result, was improved by 6% compared with that of the original model.

Owing to the widespread use of bisphenol analogues (BPs) as bisphenol A (BPA) alternatives, they have been recognized to constitute a health risk for aquatic ecosystems. The occurrence and distribution of six BPs were investigated in the truly dissolved phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. With the exception of bisphenol Z, all BPs were detected in at least two phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the truly dissolved phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the truly dissolved phase and colloidal phase, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude greater than that of SPM, suggesting that colloids play an important role in regulating the environmental behaviors of BPs. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

In this paper, spacetime is defined as the absolutely invariant homogeneous "coordinate spacetime" frame and its modulation by the relatively variable non-homogeneous "metric spacetime" under its constraints. This modulation is caused by matter and motion, and carries the function of transmitting interactions, reflecting the diffeomorphism invariance and Lorentz invariance. This inhomogeneous spacetime concept makes the medium nature of spacetime more obvious and avoids the problem of "path dependence" caused by the concept of curved spacetime. In this paper, it is argued that all energy-momentum has internal spatio-temporal properties, and all interactions must be transmitted through spacetime metrics. On this basis, a converging and dispersing cyclic multiverse model is proposed. This model of the universe is inevitable as long as there are two macroscopic manifestations of the matter of the universe, namely, gravitation induced convergence and "explosive" dispersion caused by different factors. The new cosmic model matches the observed accelerated "expansion" of the universe and no longer requires the dark energy hypothesis.

This paper empirically analyzes the relationship between digital inclusive finance and rural income, and demonstrates that digital inclusive finance plays a significant role in promoting rural income, based on the 2012-2018 panel data of 17 cities in Henan Province of China. Further dimensional research unveils that all of its breadth of coverage, depth of use and degree of digitization present significant positive correlation with rural income, and a robustness test was conducted through the sub-sample method. In addition, according to regression analysis on the influencing factors of digital inclusive finance through the Tobit model, the level of economic development, the Internet popularity rate and the urbanization rate have a positive effect on the development of digital inclusive finance in Henan, while the income gap between urban and rural areas and the degree of opening up have a negative effect. Finally, predicated on the analysis of the restrictive factors of Henan’s digital inclusive finance in increasing rural income, the paper puts forward specific policy proposals based on the native state quo.

The moon always use the same side to face toward the earth, but there is a dead angle in the mainstream theory of explaining this phenomenon. That is, it cannot explain why the moon doesn't rotate around the axis which is a straight line to connect the mass centers of the earth and moon. Because the numerous meteorite impact craters on the lunar surface indicate that the moon is completely possible to obtain external momentums and rotate around this axis. This paper proposes a plain explanation, that is, the universal gravitation between the earth and moon as well as the earth's magnetic field have formed a trinity restraint mechanism on the moon. According to this explanation, the moon's rotation can be locked, and the mechanism of lunar libration has been revealed out, which can also confirm mutually with the natural phenomenon that the moon has sought a balance in the swing. In addition, with the help of all kinds of detection data from the Apollo moon landings and other circumlunar spacecraft, as well as the studies and analysis of lunar soil samples, the conclusion is that as far as a whole for the moon, it belongs to paramagnetic substances, and its relative permeability is between 1.008 and 1.03. Although the magnetic flux density of the earth on the lunar orbit has been dropped below 0.0008125 nT or lower due to the impact of the solar wind, but it can be used as a reason to lock the moon without rotating around the axis which is a straight line to connect the mass centers of the earth and moon. If another main reason to cause the existence of this fact cannot be found, even if the magnetic flux density of the geomagnetism in lunar orbit is very small, it also should not be artificially ignored. In this regard, we can artificially change the intensity of the earth's magnetic field, and carefully observe the lunar libration and in the distance between the earth and the moon, to verify the arguments in this paper.

The early 2-factor (E2F) family of transcription factors, including E2F1-8, plays a critical role in apoptosis, metabolism, proliferation, and angiogenesis within glioblastoma (GBM). However, the specific functions of E2F transcription factors (E2Fs) and their impact on the malignancy of Bevacizumab (BVZ)-responsive GBM subtypes remain unclear. This study used data from The Cancer Genome Atlas (TCGA) and Gene Expression Omnibus (GEO) to explore the impact of eight E2F family members on the clinical characteristics of BVZ-responsive GBM subtypes and possible mechanisms of recurrence after BVZ treatment.To predict the possibility of GBM patient survival and progression, we classified and comparedthe expression of E2Fs according to BVZ-responsive subtypes and employed a machine learning method-TreeBagger, one random forest algorithm. Multiple bioinformatics analyses have shown that the significant increased E2F8 post BVZ treatment may enhance the function of angiogenesis and stem cell proliferation, indicating one of the mechanisms of GBM recurrence after treatment. In addition, BVZ treatment in unresponsive GBM patients may potentially worsen disease progression. Our findings suggest that E2F family members play important roles in GBM malignancy and BVZ treatment response, highlighting their potential as prognostic biomarkers and therapeutic targets and recommending precise BVZ treatment for GBM patients.

The existence of palindrome numbers of arbitrary length greater than 2 that are divisible by the prime number 37 is proven in this paper. The method to construct such a palindrome is also described. It turns out that a palindrome number divisible by 37 is also divisible by 3 and, consequently, divisible by 111.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

Deterministic-stochastic empirical mode decomposition (EMD) is used to obtain low-frequency (non-diffusive, i.e., background velocity) and high-frequency (diffusive, i.e., eddies) components from a Lagrangian drifter‘s trajectory. Eddy characteristics are determined from the time series of eddy trajectories from individual Lagrangian drifter such as the eddy radial scale, eddy velocity scale, eddy Rossby number, and eddy-background kinetic energy ratio. A long-term dataset of the SOund Fixing And Ranging float time series obtained near the California coast by the Naval Postgraduate School from 1992 to 2004 at depth between 150 and 600 m (http://www.oc.nps.edu/npsRAFOS/) is used as an example to demonstrate the capability of the deterministic-stochastic EMD.

In this paper, some mixed type bounds on the spectral radius $\rho(A\circ B)$ for the Hadamard product of two nonnegative matrices ($A$ and $B$) and the minimum eigenvalue $\tau(C\star D)$ of the Fan product of two $M$-matrices ($C$ and $D$) are researched. These bounds complement some corresponding results on the simple type bounds. In addition, a new lower bound on the minimum eigenvalue of the Fan product of several $M$-matrices is also presented: $$ \tau(A_{1}\star A_{2}\cdots\star A_{m})\geq \min_{1\leq i\leq n}\{\prod^{m}_{k=1}A_{k}(i,i)-\prod^{m}_{k=1}[A_{k}(i,i)^{P_{k}}-\tau(A_{k}^{(P_{k})})]^\frac{1}{P_{k}}\}, $$ where $A_{1},\ldots, A_{k}$ are $n\times n$ $M$-matrices and $P_{1},\ldots, P_{k}>0$ satisfy $\sum^{m}_{k=1}\frac{1}{P_{k}}\geq 1$. Some special cases of the above result and numerical examples show that this new bound improves some existing results.

The concept of smart morphing blades, which can control themselves to reduce or eliminate the need for active control systems, is a highly attractive solution in blade technology. In this paper an innovative passive control system based on Shape Memory Alloys (SMAs) is proposed. On the basis of previous thermal and shape characterization of a single morphing blade for a heavy-duty automotive cooling axial fan, this study deals with the numerical analysis of the aerodynamic loads acting on the fan. By coupling CFD and FEM approaches it is possible to analyze the actual blade shape resulting from both the aerodynamic and centrifugal loads. The numerical results indicate that the polymeric blade structure ensures proper resistance and enables shape variation due to the action of the SMA strips.

Tourism is an important industry that promotes national economic and social progress. All-for-one tourism is a new concept of regionally coordinated development that uses the tourism industry as an engine to boost resource integration, industrial integration, and social sharing. Tourism service is the main embodiment of cultural ecosystem services for all-for-one tourism cities. Taking Liyang in China as an example, this paper used a combination of GIS spatial analysis and big data text mining to evaluate the tourism service from three aspects: the quality of tourism resources, the comprehensiveness of tourism service facilities, and the satisfaction of tourists. The results show that (1) the tourism service is better in the northwestern and eastern areas of the city, while it is lower in the northeastern and southwestern parts; (2) the hotspot areas should focus on improving the tour routes, the transport capacity, and excessive charges; the cold spot areas should work on ecological restoration and creating new tourism attractions by combining the local industries; (3) rural tourism integrating agriculture and visitation should be highlighted as a key growth point to improve the city’s tourism service function.

Because Newton's gravity and Einstein's general theory of relativity are macroscopic gravitational theories, therefore, this paper attempts to establish a set of quantum gravity theory of the microscopic expression of Newton's and Einstein's theory of gravity to make up for the shortcomings of the existing macro-gravity theory at the micro level, and further develop the macroscopic gravity theory into the microscopic field. Based on the cognition of the field theory model, from the general assumption, space-time is further regarded as an ideal fluid, from the perspective of the distribution of ideal fluid density, this paper derives the Newton's universal gravitational equation and Einstein's general relativity equation. On the micro level, the gravitational field is further interpreted as a gradient field of space-time density; the Newtonian potential is further interpreted as the density of an object at the micro level; gravity is further interpreted as the potential pressure(space-time pressure) exhibited by the gradient of the density of the object at the micro level; flection space-time is further interpreted as the embodiment of the gradient distribution of the ideal fluid (space-time) density at the micro level. Based on a modified gravitational model, it explains the dynamics of the stars' rotation and revolution.

Poverty alleviation is a hallmark of post-revolution Chinese policymaking. Since 1978, the Communist Party of China (CPC) has implemented successive waves of poverty alleviation policies whose effects have become the focus of an ever-increasing body of academic literature. This paper reviews this diverse but limited literature that evaluates the impact of the CPC’s poverty reduction programs through four major channels, namely fiscal investment programs, social safety nets, rural governance on the village-, county- and provincial level, and the relocation of rural populations from destitute regions. This paper aims to synthesize results and evaluate whether and how the abovementioned poverty alleviation programs have had distinct positive or negative impacts on regional development outcomes. Furthermore, I highlight contradictions in empirical findings to motivate the discussion about contextual importance when designing and implementing future poverty alleviation programs. Finally, I suggest that an exhaustive and critical appraisal of the empirical strategies used in this literature would further the development and application of more accurate and informative methodologies.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

Oral cancer represents a significant global public health challenge, contributing substantially to cancer incidence and mortality. Despite established risk factors such as tobacco use and alcohol consumption, early detection remains crucial for effective treatment. This study introduces a novel approach using a transistor-based biosensor system for detecting the P90 (CIP2A) protein. We have tested the presence of CIP2A in human leukoplakia samples that can rise into oral squamous cell carcinoma. The method employs commercially available glucose test strips functionalized with P90 antibodies, providing high sensitivity and a low limit of detection, which is five orders lower than commercial ELISA kits. A specially designed printed circuit board (PCB) facilitates accurate measurements, and the device's performance is optimized through characteristic tests. Human sample testing validates the biosensor's effectiveness in distinguishing samples after cell lysis. This study contributes to advancing accurate and cost-effective diagnostic approaches for oral pre-cancer and cancer tissues.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

Forward-bias hole injection from 10 nm-thick p-type Nickel Oxide layers into 10 um-thick n-type Gallium Oxide in a vertical NiO/Ga2O3 p-n heterojunction leads to more than a factor of 2 enhancement of photoresponse measured from this junction. While it takes only 600 seconds to obtain such a pronounced increase in photoresponse, it persists for hours, indicating feasibility of photovoltaic device performance control. The effect is ascribed to charge injection-induced increase of minority carrier (hole) diffusion length (resulting in improved collection of photogenerated non-equilibrium carriers) in n-type beta-Ga2O3 epitaxial layers, due to trapping of injected charge (holes) on deep meta-stable levels in the material and subsequent blocking of non-equilibrium carrier recombination through these levels. Suppressed recombination leads to increased non-equilibrium carrier lifetime, in turn determining a longer diffusion length and being the root-cause for the effect of charge injection.

Classical mechanics describes the laws of motion in the macroscopic material world, while quantum mechanics describes the laws of motion in the microscopic material world that classical mechanics cannot explain, and achieves a highly accurate mathematical representation of the laws of microscopic physical motion. But even with such a successful theory, there is confusion about the probability wave. Therefore, this paper attempts to improve the physical definition of the conceptual basis of quantum mechanics, thus solving the confusion of quantum mechanical probability waves, and finally surprisingly discovered another feasible interpretation of the principle of cosmic redshift and the invariance of the speed of light.

Toshiba devised the bladeless fan (or Air Multiplier) concept in 1981. Researchers like James Dyson and Jafari et al. further developed it. Bladeless fans are more energy-efficient, safer due to the hidden blades, easier to clean, and more adjustable than conventional fans. From a performance point of view, bladeless fans are better because they multiply mass flow rate, eliminate buffeting, consume less power, and are quieter. This paper investigates the influence of the airfoil’s outlet slit thickness on the discharge ratio by varying the outlet slit thickness of an Eppler 473 airfoil from 1.2 mm to 2 mm in intervals of 0.2 mm. Results indicated that smaller slits showed higher discharge ratios. The airfoil with a 1.2 mm slit thickness showed a discharge ratio of 18.78, a 24% increase from the discharge ratio of the 2 mm slit. The effect of outlet angle on the pressure drop across the airfoil was also studied. Outlet angles were varied from 16∘ to 26∘ by an interval of 2∘. The airfoil profile with a 24∘ outlet angle showed a maximum pressure difference of 965 Pa between the slit and leading edge. In contrast, the 16∘ outlet angle showed the least pressure difference of 355 Pa. Parameters such as average velocity, turbulent kinetic energy, the standard deviation of velocity and outlet velocity magnitude was used to assess the performance of airfoil profiles used in bladeless fan.

Concerning fan systems with an air pipe connecting air intake and a closed outlet, aerodynamic noise cannot be directly transmitted from the fan inlet and outlet to the outside. At this moment, the volute vibrational radiation noise induced casing surface vibration is the major noise component. The main factors affecting the fan vibrational noise are analyzed through theoretical derivation, then a vibrational noise optimization control method for the volute casing is proposed that considered the influence of vibro-acoustic coupling, taking the panel thickness of the volute (front-panel thickness [FT], side-panel thickness [ST], and back-panel thickness [BT]) as design variables, and the acoustical power of the volute surface and the total mass of the volute as the optimal target function. The optimization method is mainly divided into three main parts: the first was based on the simulation of unsteady flow of the fan to obtain the vibrational noise source; the second, using the design of experimental (DOE) method and the proposed numerical simulation of fluid-structure-acoustic coupling method to obtain the designing space, then the radical-based function (RBF) method is used to construct the approximate surrogate model instead of the simulation model previously mentioned, which was used to provide the basic mathematical model for the optimization of the next part; the third part, implementing the low vibrational noise optimization for the fan volute, applied the single-target (taking volute radiated acoustical power as the target function) and the multi-target (taking the volute radiated acoustical power and volute total mass as the target function) methods. In addition, the fan aerodynamic performance, volute casing surface fluctuations, and vibration response were validated by experiments, showing good agreement. It is of utmost importance that the dynamic pressure measurements and vibrational tests on the volute casing verify the accuracy of the numerical calculation. The optimization results showed that the vibrational noise optimization method proposed in this study can effectively reduce the vibration noise of the fan, obtaining a maximum value of noise reduction of 7.3 dB. The optimization identified in this paper provides a significant reference for the design of a low-vibrational-noise volute.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

Zucchini (Cucurbita pepo L.) is an important crash crop for producing seeds in Inner Mongolia, China. In August 2021, the harvest season of seed-producing zucchini, fruit rot symptom (cv. Jindi No.1) was found in the Wuyuan region. The incidence of infected fruits of zucchini ranged from 10% to 30% and symptom consisted in 4 to 5 cm diameter lesions where the fruit was in contact with the soil. Ten isolations from six symptomatic fruits were preliminary classified as Fusarium species based on its morphological characters in potato dextrose agar. Phylogenetic tree was constructed by concatenating TEF-1α and RPB2 gene and exhibited the isolates clustered together with the Fusarium solani f. sp. cucurbitae sequences. Pathogenicity tests revealed that two isolates caused over 3 cm diameter lesions on the fruits while negative-controls remained asymptomatic. The colonies reisolated from the leasions were morphologically identical to the original isolates, thus fulfilling Koch’s postulates. Results demonstrated that F. solani f. sp. cucurbitae was the causal agent of fruit rot observed in the field. To our knowledge, this is the first report of fruit rot of seed-producing zucchini caused by F. solani f. sp. cucurbitae in Inner Mongolia, China.

Co-inhibitory receptors (Co-IRs) are essential in controlling the progression of immunopathology in rheumatoid arthritis (RA) by limiting T cell activation. The objective of this investigation was to determine the phenotypic expression of Co-IRs T cells and to assess the levels of serum soluble PD-1, PDL-2, and Tim3 in Taiwanese RA patients. Co-IRs T cells were immunophenotyped employing multicolor flow cytometry, and ELISA was utilized for measuring soluble PD-1, PDL-2, and Tim3. Correlations have been detected across the percentage of T cells expressing Co-IRs (MFI) and different indicators in the blood, including ESR, high sensitivity CRP (hsCRP), 28 joint disease activity scores (DAS28), and soluble PD-1/PDL-2/Tim3. In RA patients, we recognized elevated levels of PD-1 (CD279), CTLA-4, and TIGIT on CD4+ T cells; TIGIT, HLA-DR, TIM3, and LAG3 on CD8+ T cells; and CD8+CD279+TIM3+, CD8+HLA-DR+CD38+ T cells. The following tests proved to be correlated with hsCRP: CD4/CD279 MFI, CD4/CD279%, CD4/TIM3%, CD8/TIM3%, CD8/TIM3 MFI, CD8/LAG3%, and CD8+HLA-DR+CD38+%. CD8/LAG3 and CD8/TIM3 MFIs are linked to ESR. DAS28-ESR and DAS28-CRP exhibited relationships with CD4/CD127 MFI, CD8/CD279%, and CD8/CD127 MFI, respectively. CD4+CD279+TIM3+% was correlated with DAS28-ESR (p=0.0084, N=46), DAS28-CRP (p=0.007, N=47), and hsCRP (p=0.002, N=56), respectively. In the serum of patients with RA, levels of soluble PD-1, PDL-2, and Tim3 were extremely elevated. CD4+ TIM3+% (p=0.0089, N=46) and CD8+ TIM3+% (p=0.0305, N=46) were correlated with sTIM3 levels; sPD1 levels were correlated with CD4+CD279+% (p<0.0001, N=31) and CD3+CD279+% (p=0.0084, N=30). Co-IRs expressions on CD4+ and CD8+ T cells, as well as soluble PD-1, PDL-2, and Tim3 levels, could function as indicators of disease activity and potentially play crucial roles in the pathogenesis of RA, in accordance to our findings.

Guided image filter implicitly balances noise and details based on local variance, achieving noise suppression while preserving prominent edges. However, we have observed limitations in using variance to distinguish between noise and image details, resulting in the suppression of fine structures alongside noise. Furthermore, the goal of enhancing image details, which is crucial in image filtering, has not been adequately addressed in edge-preserving filter design. In this paper, we approach image filtering as a problem of spectral energy reconfiguration, where the gain of each spectral band is adaptively regulated to achieve simultaneous noise suppression and detail enhancement. Instead of relying on variance, we employ a linear noise estimator to obtain the Signal-to-Noise Ratio (SNR) measurement necessary for dynamic gain regulation. Similar to the guided image filter, we determine the filter coefficients by solving the closed-form solution of the optimizer. We demonstrate that the proposed extended guided filter effectively integrates information from multiple spectral bands locally, allowing for the joint enhancement of meaningful details while simultaneously smoothing noise.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

There are unsolved problems related to inflation, gravity, dark matter, dark energy, missing antimatter, and the birth of the universe. Some of them can be better answered by assuming the existence of aether and hypoatoms. Both were created during the inflation in the very early universe. While aether forms vacuum, hypoatoms, composed of both matter and antimatter and believed to be neutrinos, form all observable matter. In vacuum, aether exists between the particle-antiparticle dark matter form and the dark energy form in a dynamic equilibrium: A + A-bar = gamma + gamma. The same reaction stabilizes hypoatoms and generates a 3-dimensional sink flow of aether that causes gravity. Based on the hypoatom structure, the singularity does not exist inside a black hole; the core of the black hole is a hypoatom star or neutrino star. By gaining enough mass, ca. 3 X 10²² M_sun, to exceed neutrino degeneracy pressure, the black hole collapses or annihilates into the singularity, thus turning itself into a white hole or a Big Bang. The universe is anisotropic. Its center, or where the Big Bang happened, is at 0.66^+0.03_-0.01 times the radius of the observable universe at Galactic coordinates (l, b) = (286⁺¹⁰_-10, -43⁺⁷_-6). If we look from the Local Group to the center of the universe, the universe is rotating clockwise.

Astrocytes are essential for normal brain development and functioning. They respond to brain injury and disease through a process referred to as reactive astrogliosis, where the reactivity is highly heterogenous and context dependent. Reactive astrocytes are active contributors to brain pathology and can exert beneficial, detrimental, or mixed effects following brain insults. Transforming growth factor-β (TGF-β) has been identified as one of the key factors regulating astrocyte reactivity. Genetic and pharmacological manipulation of TGF-β signaling pathway in animal models of CNS injury and disease alters pathological and functional outcomes. This review aims to provide recent understanding regarding astrocyte reactivity and TGF-β signaling in brain injury, aging, and neurodegeneration. Further, it explores how TGF-β signaling modulates astrocyte reactivity and function.

Leucokinins (LKs) constitute a neuropeptide family first discovered in a cockroach and later identified in numerous insects and several other invertebrates. The LK receptors are only distantly related to other known receptors. Among insects, there are many examples of species where genes encoding LKs and their receptors are absent. Furthermore, genomics has revealed that LK signaling is lacking in several of the invertebrate phyla and in vertebrates. In insects, the number and complexity of LK expressing neurons vary, from the simple pattern in the larva of Drosophila where the entire CNS has 20 neurons of three main types, to cockroaches with about 250 of many different types. Common to all studied insects is the presence or 1-3 pairs of LK-expressing neurosecretory cells in each abdominal neuromere of the ventral nerve cord, that, at least in some insects, regulate secretion in Malpighian tubules. This review summarizes the diverse functional roles of LK signaling in insects, as well as other arthropods and mollusks. These functions include regulation of ion and water homeostasis, feeding, sleep-metabolism interactions, state-dependent memory formation, as well as modulation of gustatory sensitivity and nociception. Other functions are implied by the neuronal distribution of LK, but remain to be investigated.

Activities in the digital economy driven by information technology have rapidly increased in scope and speed in the aftermath of COVID-19. Meanwhile, social isolation accelerated by quarantine measures has increased concerns about individuals’ mental health. However, little is known about the specific consequences of online interactions, especially when applied in online fan community-based relationships where loyal community members are prevalent. Therefore, we examined whether a sense of virtual community (SOVC) can link fans’ online activities with their mental well-being and behavioral loyalty to the platform. For this purpose, we focus on BTS fandom “Adorable Representative MC for Youth” (ARMY) behaviors and attitudes on the fan community platform Weverse. With 202 valid data samples acquired from global ARMY, this study conducted a partial least squares–structural equation modeling analysis. The empirical findings reveal that SOVC in Weverse is significantly influenced by the intensity of online interactions with other fans and parasocial relationships with celebrities. SOVC is found to be the direct predictor of fans’ behavioral loyalty and mental well-being. When considering fans’ perceptions of other social media platforms, dissatisfaction with previous online fan communities enhances the intensity of online interactions with other fans in Weverse.

The rapid urbanization has exerted tremendous pressure on natural systems in mountains. As a measure of sustainable use of natural resources, ecological footprint is an important basis for judging whether the development of a country or region is within the biocapacity. Taking Dali Bai Autonomous Prefecture as an example, this study comprehensively analyzes the impact of human activities on mountain resources and environment from the three aspects of urbanization, land use and ecological carrying capacity. The results show that Dali Prefecture with the urbanization rate of 33% is still in the accelerated stage of urbanization. The urban space presents the core-periphery feature, and the central city is the focus of human existence and living activities. The per capita ecological footprint is 1.14 hm2/person higher than the ecological carrying capacity, meaning Dali Prefecture is in an ecological deficit state. This indicates that there is an uncoordinated state between urbanization and environment. Arable land is the main source of per capita ecological footprint in the prefecture. However, the urban expansion overly occupies the arable land in the plain sub-region, leading the arable land to an ecological deficit state. In the future, the development of the mountainous area should focus on the protection of arable land and choose a new sustainable path.

It is generally believed that the universe emerged from the Big Bang, before which space and time did not exist. However, Penrose proposed his theory of conformal cyclic cosmology, in which an aeon existed preceding this universe. Based on the cosmological principle, the universe is homogeneous and isotropic, expanding without center, but recently more and more deviations have been observed. By studying the fundamental particles and reactions of nature, we initiated a model that the Big Bang is the result of the collapse of a neutrino star within a black hole. We therefore re-analyze the cosmic microwave background (CMB) and find that the Center of the universe where the Big Bang occurred was at 0.66 ^+0.03 _-0.01 times the radius of the surface of last scattering away from the Local Supercluster (LS) and at Galactic coordinates (l, b) = (286^o +/- 10^o, -43^{o +7} _-6). If we look from the LS to the Center, the universe is spinning clockwise. Our findings are supported by Penrose’s conformal cyclic cosmology, low-variance circle sets in the CMB, and many other independent observational evidence of cosmic inhomogeneities, spatial anisotropies, and time variations.

In order to balance the conflicts among mass flow rate, total pressure ratio, adiabatic efficiency and stall margin in a low-bypass transonic fan, the optimization of the rotor blade is implemented in this study. An advanced 3D optimization design system is adopted, and flow diagnostic methods based on vorticity dynamics are employed to discuss the flow field. Results indicate that by controlling the blade camber line curvature, significant improvements in the aerodynamic performance for the fan stage are achieved, the total pressure ratio is increased by 1.90%, while the adiabatic efficiency and mass flow rate are increased by 4.45% and 5.82%, respectively. Vorticity diagnosis suggest that there exists a close link between performance parameters and vorticity parameters in the axial fan/compressor, both azimuthal vorticity and boundary vortex flux have significant influences on the stage performance. Moreover, the boundary layer separation is accompanied by the spike of entropy and static pressure, while the derivation/gradient of these flow parameters would also suffer drastic changes under the effect of shock wave. The vorticity parameters could provide detailed flow information about the on-wall flow with high accuracy, which provides the researchers with a novel method for the turbomachinery aerodynamic design and analysis.

New innovative green concepts in electrified vertical take-off and landing vehicles currently emerge as a revolution to urban mobility going into the third dimension (vertically). The high population density of cities makes the market share highly attractive while posing an extraordinary challenge for community acceptance due to the increasing and possibly noisier commuter traffic. In addition to passenger transport, package deliveries to customers by drones may enter the market. The new challenges associated with this increasing transportation need in urban, rural and populated areas pose challenges for established companies and startups to deliver low-noise emission products. The article's objective is to revisit the benefits and drawbacks of an affordable acoustic measurement campaign focused on early prototyping. In the very early phase of product development, often considerably limited resources are available. With this in mind, the article discusses the sound power results using the enveloping surface method in a typically available low-reflection room with a reflecting floor according to DIN EN ISO 3744:2011-02. The method is applied to a subsonic electric ducted fan (EDF) unit of a 1:2 scaled electrified vertical take-off and landing vehicle. The results show that considerable information at low costs can be gained for the early prototyping stage, despite this easy-to-use, easy-to-realize, and not fine-tuned measurement setup. Furthermore, the limitations and improvements to a possible experimental setup are presented to discuss a potentially more ideal measurement environment. Measurements at discrete operating points and transient measurements across the total operating range were conducted to provide complete information on the EDF's acoustic behavior. The rotor-self noise and the rotor-stator interaction were identified as primary tonal sound sources, along with the highest broadband noise sources located on the rotor. Based on engineering experience, a first acoustic improvement treatment is also quantified with a sound power level reduction of 4dB(A). In conclusion, the presented method is a beneficial first measurement campaign to quantify the acoustic properties of an electric ducted fan unit at minimal resources in a reasonable time of several weeks when starting from scratch.

Topography represented by high resolution digital elevation models are able to inform past and present morphological process on the terrain. High resolution LiDAR data taken by the General Directorate of Map at the surroundings of the Bergama city shows great opportunities to understand the morphological process on alluvial fan on which the city is located and the flood plain of Bakırçay river near the alluvial fan. In this paper the LiDAR data collected in 2015 have been used to create DEM’s to understand the geomorphological evolution of the alluvial fan and the flood plain around it. Since the proximal roots and medial parts of the alluvial fan have been the scene for a long human settlement most topographical traces of the morphological process have been distorted. Nevertheless, the traces of past and present morphological process at the distal fan which consist the contact zone with the flood plain are very clear on the DEM created from LiDAR data. The levees and some old courses of Bergama and Bakırçay rivers have been shown on the maps which are also important to understand the ancient roads which follows these levees.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

Air passenger traffic prediction is crucial for the effective operation of civil aviation airports. Despite some progress in this field, the prediction accuracy and methods need further improvement. This paper proposes an integrated approach to the prediction of air passenger index as follows. Firstly, the air passenger index is defined and classified by the K-means clustering method. Based on the mutual information (MI) principle, the information entropy is used to analyze and select the key influencing factors of air passenger travel. By incorporating the MI principle into the support vector regression (SVR) framework, this paper presents an innovative MI-SVR machine learning model used to predict the air passenger index. Finally, the proposed model is validated by passenger throughput data of the Shanghai Pudong International Airport, China. The experimental results prove the model feasibility and effectiveness by comparing them with conventional methods, such as ARIMA, LSTM, and other machine learning models, outperformed by the MI-SVR model. Besides, it is shown that the prediction effect of each model could be improved by introducing influencing factors based on mutual information. The main findings are considered instrumental to the airport operation and air traffic optimization.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

The experiments of Project 8 have been excellent, but the expected goals still difficult to achieve. So much so that some of the results at your fingertips were also missing. In view of this, the focus of this article is to clarify several easy confused concepts. Only in this way, we can reasonably explain the experimental data. The main points are as follows: 1. The value c of the light speed in vacuum and a particle with zero static mass, both of which do not exist in the reality. That is to say, the so-called a photon's static mass is equal to zero but has energy, which is a paradox that confuses two different definitional domains. 2. In the reality, photons are high-speed particles generated by electromagnetic radiation. They must have the characteristics of (static) mass, energy and wave, in order to describe the main body to aim at photons from different angles. 3. After any main body comes into being electromagnetic radiation, its static mass will inevitably decrease accordingly. 4. The charge-mass ratio of an electron is a physical constant, which is the ratio of its charge to the amount of matter, and is not affected by relativistic effects and electromagnetic radiation. 5. The uncertainty of moving electrons is caused by random electromagnetic radiations. Finally, it is pointed out that if the cyclotron frequency of a single electron is measured, and at the same time, its de Broglie wavelength or frequency can also be measured, then its static mass can be obtained. Even so, the expected goals are still difficult to achieve, because random electromagnetic radiations are always taking away continually the matter composition of the single electron being measured. However, this was precisely a result of the research obtained by Project 8, and had universality, which should be reflect on.

A Systemic Lupus Erythematosus (SLE) is a prototypical systemic autoimmune disease characterized by a complex interplay of genetic, molecular, and cellular factors. It is considered a multifactorial disorder influenced by genetic susceptibility, environmental triggers, and dysregulated immune responses. Understanding the molecular and cellular mechanisms driving SLE pathogenesis has been instrumental in developing targeted therapies to manage the disease and improve patient outcomes. In this essay, we will delve into the intricate molecular and cellular processes underlying SLE and examine the key lessons learned from human therapies.

Recent advances in differential topology single out four-dimensions as being special, allowing for vast varieties of exotic smoothness (differential) structures, distinguished by their handlebody decompositions, even as the coarser algebraic topology is fixed. Should the spacetime we reside in takes up one of the more exotic choices, and there is no obvious reason why it shouldn't, apparent pathologies would inevitably plague calculus-based physical theories assuming the standard vanilla structure, due to the non-existence of a diffeomorphism and the consequent lack of a suitable portal through which to transfer the complete information regarding the exotic physical dynamics into the vanilla theories. An obvious plausible consequence of this deficiency would be the uncertainty permeating our attempted description of the microscopic world. We tentatively argue here, that a re-inspection of the key ingredients of the phenomenological particle models, from the perspective of exotica, could possibly yield interesting insights. Our short and rudimentary discussion is qualitative and speculative, because the necessary mathematical tools have only just began to be developed.

It is well known but under-appreciated in astrophysical applications, that it is possible for gravity to take on a life of its own in the form of Weyl-curvature-only metrics (note we are referring to the Weyl-only solutions of ordinary General Relativity, we are not considering Weyl conformal gravity or any other modified gravity theories), as numerous examples demonstrate the existence of gravitational fields not being sourced by any matter. In the weak field limit, such autonomous gravitational contents of our universe manifest as solutions to the homogeneous Poisson's equation. In this note, we tentatively explore the possibility that they may perhaps account for some phenomenologies commonly attributed to dark matter. Specifically, we show that a very simple solution of this kind exists that can be utilized to describe the rising tails seen in many galaxy rotation curves, which had been difficult to reconcile within the cold dark matter or modified Newtonian dynamics frameworks. This solution may also help explain the universal $\sim 1$Gyr rotation periods of galaxies in the local universe.

Semantic communication is not obsessed with improving the accuracy of transmitted symbols, but is concerned with expressing the desired meaning that the symbol sequence exactly carried. However, the generation and measurement of semantic messages are still an open problem. Expansion combines simple things into complex systems and even generates intelligence, which is consistent with the evolution of the human language system. We apply this idea to semantic communication system, quantifying and transmitting semantics by symbol sequences, and investigate the semantic information system in a similar way as Shannon did for digital communication systems. This work was the first to propose the concept of semantic expansion and knowledge collision, which may provide a new paradigm for semantic communications. We believe that expansion and collision will be the cornerstone of semantic information theory.

In foggy weather scenarios, the scattering and absorption of light by water droplets and particulate matter cause object features in images to become blurred or lost, presenting a significant challenge for target detection in autonomous driving vehicles. To tackle this problem, this study proposes a foggy weather detection method, YOLOv5s-Fog, based on the YOLOv5s framework. The model enhances the feature extraction and expression capabilities of YOLOv5s by introducing a novel target detection layer, SwinFocus. Additionally, this research incorporates decoupled head into the model and replaces the conventional non-maximum suppression method with Soft-NMS. Experimental results demonstrate that these improvements effectively enhance the detection performance for blurry objects and small targets in foggy weather conditions. Compared to the baseline model YOLOv5s, YOLOv5s-Fog achieves a 5.4% increase in mAP on the RTTS dataset, reaching 73.4%. This method provides technical support for rapid and accurate target detection in adverse weather conditions, such as foggy weather, for autonomous driving vehicles.

Sphalerite has been recognized as the most important carrier of critical metal of Indium (In) due to that In mainly exists in the sphalerite lattice by isomorphic substitution. There are two significant replacing schemes for In entry into sphalerite, these are, Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+. In order to understand the reaction process and constraints of the two substitution schemes, this paper uses first-principles methods to calculate In and Ag, Cu replacing Zn in sphalerite. According to the substitution schemes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, two doped sphalerite systems of Zn30InAgS32 and Zn30InCuS32 were constructed using 2×2×2 supercell model of sphalerite. Firstly, the pressure is controlled to 30MPa, and the temperature is set from 20-40MPa to simulate the response of the two doped sphalerite systems to temperature; Then, the control temperature was unchanged to 600K, and the pressure was set from 20-40MPa to investigate the pressure control of the two doped sphalerite systems. The lattice parameters, substitution energy, electronic structure, and population analysis of the designed models before and after replacement have been critically compared. The main conclusions can be drawn that it is more stable for In to enter sphalerite via the coupled substitution scheme Cu++In3+→2Zn2+, and the conditions that the two substitution schemes most likely to occur are 650K and 40MPa. This study not only reveals the physical and chemical properties of In-rich sphalerite formed by the two reaction processes of Ag++In3+→2Zn2+ and Cu++In3+→2Zn2+, but also has a certain enlightenment effect on the search for indium in sphalerite, and promotes the application of first principles in mineralization analysis.

An energy model that correlates fan airflow, head, speed, and system power input is essential to detect device faults and optimize control strategies in fan systems. Since the application of variable frequency drives (VFDs) makes the motor efficiency data published by manufacturers inapplicable, the fan efficiency and drive (belt-motor-VFD) efficiency must be identified for each individual system to obtain accurate energy models. The objectives of this paper are to identify an energy model of existing VFD-motor-fan systems using available experimental data and demonstrate its applications in loose belt fault detection and virtual airflow meter development for optimal control. First, an approach is developed to identify the fan head, fan efficiency and drive efficiency curves using available fan head, speed, and system power input as well as temporarily measured airflow rate without measuring shaft power. Then the energy model is identified for an existing VFD-motor-fan system. Finally, the identified model is applied to detect the slipped belt faults and develop the virtual airflow meter. The experiment results reveal that the developed approach can effectively obtain the energy model of VFD-motor-fan systems and the model can be applied to effectively detect slipped belt faults and accurately calculate the fan airflow rate.

Plant-microbe interactions are essential for ecosystem health and agricultural productivity. Metabolomics has revolutionized our understanding of these interactions by providing powerful methods to decipher the complex chemical signals involved. This review highlights the various metabolomics techniques used to study plant-microbe interactions, such as mass spectrometry, nuclear magnetic resonance spectroscopy, and advanced imaging technologies. We also discuss the role of contemporary bioinformatics tools, extensive databases, and the increasing influence of artificial intelligence and machine learning in the analysis of metabolomics data. Integrating metabolomics with other omics fields, including transcriptomics, proteomics, and metagenomics, allows for a comprehensive understanding of the molecular mechanisms underlying plant-microbe interactions. The review emphasizes the significance of fluxomics in elucidating the dynamic nature of metabolic networks. While there are challenges in data analysis, integration, and interpretation, metabolomics has profoundly expanded our knowledge of the role metabolites play in shaping plant-microbe interactions. As metabolomics technologies advance and integrate further with other omics approaches, we anticipate groundbreaking discoveries that will provide deeper insights into these complex interactions, ultimately leading to innovative strategies for sustainable agriculture and biotechnology.

Gesture recognition technology has been quickly developed in the field of human-computer interaction. The multiple-input multiple-output (MIMO) radar has been widely adopted in gesture recognition because of its notable spatial resolution. In this work, a highly accurate MIMO radar-based hand gesture recognition algorithm with very low complexity is proposed. To make the proposed system applicable in the industry and work well even when the size of the training data is limited, we applied several low-complexity adaptive signal processing methods to extract features and reduce the noise effect. First, spectrum analysis is applied to range-Doppler maps (RDMs) and a cell-averaging constant false alarm rate (CA-CFAR) with mirror filters is applied to improve the robustness to noise. Afterward, the features related to the distance, speed, direction, and the elevation angle of the moving object are determined by the proposed adaptive signal analysis techniques and the random forest is applied for classification. The proposed system has the capability to precisely distinguish and identify eight motions, including waving, moving to the left or right, patting, pushing, pulling, and rotating clockwise or anticlockwise, with an accuracy of 95%. Experiments demonstrate the capability of the proposed hand gesture recognition system to classify different movements precisely.

Prediction of protein-ligand binding affinities is crucial for computational drug discovery. A number of deep learning approaches have been developed in recent years to improve the accuracy of such affinity prediction. While the predicting power of these systems have advanced to some degrees depending on the dataset used for model training and testing, the effects of the quality and quantity of the underlying data have not been thoroughly examined. In this study, we employed erroneous datasets and data subsets of different sizes, created from one of the largest databases of experimental binding affinities, to train and evaluate a deep learning system based on convolutional neural networks. Our results show that data quality and quantity do have significant impacts on the prediction performance of trained models. Depending on the variations in data quality and quantity, the performance discrepancies could be comparable to or even larger than those observed among different deep learning approaches. In particular, the presence of proteins during model training leads to a dramatic increase in prediction accuracy. This implies that continued accumulation of high-quality affinity data, especially for new protein targets, is indispensable for improving deep learning models to better predict protein-ligand binding affinities.

Cooling fans are one of the critical components of air-forced (AF) dry-type transformers for regulating internal temperatures. Therefore, effective malfunction detection is crucial to maintain the transformer temperature within an acceptable range and prevent overheating. Regular maintenance occurs periodically and issues with cooling fans may arise between maintenance periods, leading to prolonged operation under malfunctioning conditions and potential failures. In addition, utilities typically have online information about whether a fan works or not without providing information about cooling fan malfunctioning circumstances. To address these challenges, this study proposes learning-based online monitoring techniques to detect malfunctions in AF transformer cooling fans. Random forests (RFs) and convolutional neural networks (CNNs) are developed to classify the audio signals from cooling fans into normal and malfunctioning classes. Unlike RFs, which require separate feature extraction, CNNs are trained based on spectrogram images derived from audio signals. Thus, various time-frequency techniques are utilized for feature extraction in RFs. Besides, multiple data augmentation techniques are employed to enhance the dataset size and diversity. Algorithmic performance is optimized through hyperparameter tuning and classifier threshold adjustment. Simulations reveal that CNNs outperform RFs, whereas the latter provides superior interpretability of acoustic features compared to the former.

Ischemic stroke is one of the most disabling diseases and a leading cause of death globally. Despite advances in medical care, the global burden of stroke continues to grow, as no effective treatments to limit or reverse ischemic injury to the brain are available. However, recent preclinical findings have revealed the potential role of transient receptor potential cation 6 (TRPC6) channels as endogenous protectors of neuronal tissue. Activating TRPC6 in various cerebral ischemia models has been found to prevent neuronal death, whereas blocking TRPC6 enhances sensitivity to ischemia. Evidence has shown that Ca2+ influx through TRPC6 activates cAMP response element-binding protein (CREB), an important transcription factor linked to neuronal survival. Additionally, TRPC6 activation may counter excitotoxic damage resulting from glutamate release by attenuating the activity of NMDA receptors of neurons by posttranslational means. Unresolved though, are the roles of TRPC6 channels in non-neuronal cells such as astrocytes and endothelial cells. Moreover, TRPC6 channels may have detrimental effects on the blood-brain barrier, although their exact role in neurovascular coupling requires further investigation. This review discusses evidence-based cell-specific aspects of TRPC6 in the brain to assess the potential targets for ischemic stroke management.

Studying hydro-meteorological factors variations and its links to large-scale atmospheric circulation systems can facilitate the understanding of the hydrological processes and sustainable water resources management in the source region of the Yangtze River (SRYR). Currently, researches mostly focused on the temporal and spatial variation characteristics in hydro-meteorological factors; however, researches on the hydro-meteorological variations and its links to large-scale atmospheric circulation systems in the SRYR are scarce. Based on long-term hydro-meteorological and reanalysis data, this research investigated multiscale variations of hydro-meteorological factors and its links to large-scale atmospheric circulation characteristic indices during 1957~2012 in the SRYR. The results showed that the amounts of streamflows and precipitation in the SRYR declined during the 1990s. Since the 2000s, the amounts of streamflows and precipitation had increased significantly climate in the SRYR. The change trends of precipitation and streamflows in the SRYR are synergetic at annual and seasonal scales, and have three significant periods, namely 3~5 years, 15–20 years and 30–40 years. The South Asia monsoon (SAM) plays a relatively more important role in the hydro-meteorological factors changes in the SRYR. The relative contributions of SAM to streamflows and precipitation changes were 83.6% and 78%, respectively. During the driest (wettest) year, the SAM is relatively weak (strong), and brings less (more) southwest airflow into the SRYR, less (more) precipitation and streamflows will be generated in the SRYR.

Global warming poses a threat to plant survival, impacting growth and agricultural yield. Protein turnover, a critical regulatory mechanism balancing protein synthesis and degradation, is crucial for cellular response to environmental changes. We investigated the effects of elevated temperature on proteome dynamics in Arabidopsis thaliana seedlings using 15N-stable isotope labeling and ul-tra-performance liquid chromatography-high resolution mass spectrometry, coupled with the ProteinTurnover algorithm. Analyzing different cellular fractions from plants grown under 22°C and 30°C growth conditions, we found significant changes in the turnover rates of 571 proteins, with a median 1.4-fold increase, indicating accelerated protein dynamics under thermal stress. Notably, soluble root fraction proteins exhibited smaller turnover changes, suggesting tissue-specific adap-tations. Significant turnover alterations occurred with redox signaling, stress response, protein folding, secondary metabolism, and photorespiration, indicating complex responses enhancing plant thermal resilience. Conversely, proteins involved in carbohydrate metabolism and mito-chondrial ATP synthesis showed minimal changes, highlighting their stability. This analysis high-lights the intricate balance between proteome stability and adaptability, advancing our under-standing of plant responses to heat stress and supporting the development of improved thermo-tolerant crops.

Mutations of PKD1 coding for polycystin-1 (PC1) account for most of the autosomal dominant polycystic kidney disease (ADPKD). The extracellular region of PC1 contains many evolutionarily conserved domains for ligand interactions. Among these is the leucine-rich repeats (LRR) in the far N-terminus of PC1. Using zebrafish (Danio rerio) as an in vivo model system, we explored the role of LRR in the function of PC1. Zebrafish expresses two human PKD1 paralogs, pkd1a and pkd1b. Knockdown of both genes in zebrafish by morpholino antisense oligonucleotides produced phenotypes of dorsal axis curvature and pronephric cyst formation. We found that overexpression of LRR suppressed both phenotypes in pkd1-morphant zebrafish. Purified recombinant LRR domain inhibited proliferation of HEK cells in culture and interacted with the heterotrimeric basement membrane protein laminin-511 (α5β1γ1) in vitro. Mutations of amino acid residues in LRR structurally predicted to bind laminin-511 disrupted LRR-laminin interaction in vitro and neutralized the ability of LRR to inhibit cell proliferation and cystogenesis. Our data support the hypothesis that the extracellular region of PC1 plays a role in modulating PC1 interaction with the extracellular matrix and contributes to cystogenesis of PC1-deficiency.

This research presents a comprehensive framework for efficiently generating forest fire datasets from Google Earth Engine data sources. The primary contribution of this work lies in providing a methodology to swiftly extract forest fire factors without the need for permissions or access to private datasets, rendering the dataset openly accessible and shared without barriers. Furthermore, given that the remote sensing data used is a global dataset, it can be applied in any region without restrictions. In this study, Peninsular Malaysia is chosen as a case study to demonstrate the framework's effectiveness. The generated dataset includes essential variables including the climate and environment, landcover, topography, and anthropogenic factors facilitating the analysis of fire occurrences. The methodology empowers data scientists, enabling them to leverage their analytical skills on the extracted dataset without requiring specialized remote sensing knowledge. Additionally, this study also showcases the adoption of large language models, specifically GPT-4 with the Noteable plugin, as a tool for conducting preliminary analyses on the generated dataset. Sample analyses reveal that several key features, including the KBDI, LST, PDSI, climate water deficit, and precipitation, significantly impact forest fire occurrences in Peninsular Malaysia. Despite the successful application of the GPT-4 with Noteable plugin, certain limitations and challenges are identified, highlighting the necessity for further validation of the tool's applicability and limitations. This study encourages future research to (1) adopt the proposed framework in other regions, (2) explore more detailed analyses encompassing all variables, and (3) leverage machine learning for advanced forecasting.

Automobile industry is recognized as one of the most influential sectors shaping the global economies, societies, and individual lifestyles. Therefore, fierce competitions among different companies are continuously undergoing, and innovations deserve special attention to improve the competitiveness. In the past several years, additive manufacturing (AM) is emerging as an innovative technology in the applications of automobile industry with significant advantages over traditional techniques. As a result, increasing attention has been attracted to combining AM technology with the development of automobile industry. Currently, many automobile players are optimizing their industrial layout by incorporating with innovative AM techniques, and meanwhile, many research progresses have been achieved to meet the market demand. This article aims at presenting a timely review to conclude the recent advances in the application of AM techniques in automobile industry, focusing on the available AM techniques, printable materials, and the industry applications. The future research opportunities and challenges are also outlooked. Hopefully, this work can be useful to the related researchers, as well as the game players in the industry of this field.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

A pilot study regarding the transplantation of 100 specimens of the critically endangered Pinna nobilis took place in summer of 2019 in Maliakos Gulf (Central Aegean, Greece). In this study we present the relationships between total height (HT, in cm), unburied length (UL, in cm), and shell width (SW, in cm) for P. nobilis and the relationship between HT and net weight (W, in g). Length-length relationships were all linear for all cases: r2 > 0.900), whereas the relationship between HT and W was exponential with the value of the exponent b being allometric. "Ecology, Conservation and Restoration of Threatened Animal"

As the first time, 0D-1D-3D and fully 3D steady-state aero-thermo-fluid simulations of a structural oil-to-air Fan Outlet Guide Vane Cooler (FOGVC) in a jet engine are presented. Using the commercial softwares Ansys Fluent, the thermo-mechanical module of Ansys and the 1D fluid solver Flownex, 5 simulation types (3D fully conjugate heat transfer with and without a thin wall model, 3D with a thin wall model, 1D-3D coupled, 1D and 0D) corresponding to 4 levels of simplification in 3 possible domains (oil, oil-metal and oil-metal-air) have been compared to provide selection criteria when a determined level of accuracy in the simulations without prohibited computational times is desired. The methodologies are applied to two different oil internal cavities: an inverted U with rectangular cross section and a coil internal cavity with a circular cross section. The obtained results show that depending on the scope of the research (outlet oil temperature, dissipated heat rate or oil pressure drop) and the accuracy of the results, one method or the other may be used. Experimental data would be needed to validate the numerical results by all employed methodologies and geometries.

Sunflower is one of the oil crops and its planting areas was listed behind Soybean, peanut and rapeseeds in China. It will encounter different kind of diseases during planting, thus limited the seeds yield. Fusarium species are the major threat to different crops nowadays, it is very important to identify the species caused diseases on different hosts, so that the potential control measures may be explored. In Inner mongolia, Sunflower Disk Rot (SDR) was found in different sunflower planting field, the average infection ratio around 8.50%, typically in some verieties, its infection ratio reach to 11.67%. The diseased receptacle were collected from different locations and Koch’s postulate was conducted. The results showed that Fusarium verticillioides was the main causal agent caused SDR. Fungicide toxicity tests shown that Fludioxonil and Flutolanil were screened out from six fungicides for controlling F. verticillioides, with EC50 values of 0.05 µg/mL (R = 0.9825) and 0.96 µg/mL (R = 0.9964) , respectively. This is the first report of SDR caused by F. verticillioides, and it will alert sunflower reseachers to include SDR in the disease list, so as to control sunflower diseases with integrated management strategy successfully.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Private Set Intersection Cardinality(PSI-CA) is a cryptographic method in secure multi-party computation that allows entities to identify cardinality of the intersection without revealing their private data.Traditional approaches assume similar-sized datasets and equal computational power, overlooking practical imbalances.In real-world applications, dataset sizes and computational capacities often vary, particularly in the Internet of Things and mobile scenarios where device limitations restrict computational types. Traditional PSI-CA protocols are inefficient here, as computational and communication complexities correlate with the size of larger datasets. Thus, adapting PSI-CA protocols to these imbalances is crucial.This paper explores unbalanced scenarios where one party (the receiver) has a relatively small dataset and limited computational power, while the other party (the sender) has a large amount of data and strong computational capabilities.This paper, based on the concept of commutative encryption, introduces Cuckoo filter, cloud computing technology, homomorphic encryption, among other technologies, to construct three novel solutions for unbalanced Private Set Intersection Cardinality (PSI-CA): an unbalanced PSI-CA protocol based on Cuckoo filter, an unbalanced PSI-CA protocol based on single cloud assistance, and an unbalanced PSI-CA protocol based on dual cloud assistance. Depending on performance and security requirements, different protocols can be employed for various applications.

Although Support Vector Machines (SVM) are widely used for classifying human motion patterns, their application in the automatic recognition of dynamic and static activities of daily life in the healthy older adults is limited. Using a body mounted wireless inertial measurement unit (IMU), this paper explores the use of SVM approach for classifying dynamic (walking) and static (sitting, standing and lying) activities of the older adults. Specifically, data formatting and feature extraction methods associated with IMU signals are discussed. To evaluate the performance of the SVM algorithm, the effects of two parameters involved in SVM algorithm—the soft margin constant C and the kernel function parameter $\mathsf{\gamma }$—are investigated. The changes associated with adding white-noise and pink-noise on these two parameters along with adding different sources of movement variations (i.e., localized muscle fatigue and mixed activities) are further discussed. The results indicate that the SVM algorithm is capable of keeping high overall accuracy by adjusting the two parameters for dynamic as well as static activities, and may be applied as a tool for automatically identifying dynamic and static activities of daily life in the older adults.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

No-till and cereal-legume intercropping have been recognized as favorable cropping practices to increase crop yields while maintaining soil quality in arid and semiarid environment, but the bio-logical mechanisms are poorly understood. The present study was to determine the response of soil properties, enzyme activities, and microbial community diversity and composition in mono- and inter-cropping under conventional and no-tillage conditions. We initiated a field experiment in Wuwei, a typical arid area of China, in 2014. Soil was sampled in August 2022 and, yields, soil properties, enzyme activities, and the microbial community diversity and composition were de-termined in the maize and pea strips in inter- and mono-cropping systems. Results revealed that the maize and pea strips in the no-till intercropping significantly increased yields, total and or-ganic carbon stocks, decreased NO3--N, and obtained the highest total and organic P in the soil. The α- and β-diversity of archaea and eukaryotes were significantly affected by planting patterns, while α- and β-diversity of the bacterial community were significantly affected by tillage practices. Both no-tillage and intercropped maize significantly increased the abundance of archaea phylum Thaumarchaeota and bacterial phylum Nitrospirae, benefiting nitrogen fixation of intercropped pea from the atmosphere under the no-tillage cereal/legume intercropping. No-till intercropping was conducive to the accumulation of organic carbon, while decreasing the abundance of Prote-obacteria, Acidobacteria, and Verrucomicrobia. Limited soil enzyme activities (ACP, ALP, DP, NAG, BG, AG, CB) led to decreases in organic carbon turnover and utilization. Intercropping al-tered soil microbial community diversity and composition due to changes in soil properties and enzyme activities. These findings suggest that no-tilled cereal-legume intercropping is a sustaina-ble cropping practice for improving soil properties and enhancing microbial (archaea, bacterial, Eukaryota) diversity, but the long-term persistence is not conducive to rapid turnover of soil nu-trients due to limited enzyme activities.

The first appearance of viruses can date back to the late last century. As an effective form of malware, viruses reside in the permanent storage of target hosts. Before a virus can execute, that must load into memory from the persistent storage included in the associated file. Due to the reliable destructive power of viruses, many mechanisms have been developed to defend computer systems against these hazardous threats. Antivirus software is one of the most famous and popular among these mechanisms. Most antivirus software uses static analysis (signature-based) technology on files stored in permanent storage, such as hard disks or USB flashes, to detect viruses hidden in files. Fileless malware was developed to enhance the survivability of malware by circumventing detection. Fileless malware only exists in the target hosts’ memory, not files. Antivirus software cannot even access the fileless malware code, much less analyze it, since it may be performed in memory directly without needing to load it from a disk. As a result, it is difficult for an antivirus engine to defend a system against fileless malware attacks. This paper proposes a kernel-based solution called Check-on-Execution (CoE) to detect fileless malware on a Linux system. When a program is going to execute a piece of code in a writable and executable memory area of a process, CoE suspends the code execution first. Coe retrieves the code from memory, packs the code with an ELF header to create an ELF file, and uses VirusTotal to check the file to prevent a Linux system from executing fileless malware. Experimental results show that CoE noticeably enhances the ability of a Linux system to defend itself again fileless malware. CoE is also suitable for protecting a system from shell code injection attacks, such as buffer and heap overflow attacks. It is capable of handling even packed malware. But in this paper, we only focus on fileless malware.

The recent rise in ocean temperatures, accompanied by other environmental changes, has notably increased the occurrence and spread of diseases in Octocorallia, of which many species are integral to shallow tropical and subtropical coral reef ecosystems. This study focuses on the understanding of these diseases, which has been largely limited to symptomatic descriptions, with clear etiological factors identified in only a fraction of cases. A key example is the multifocal purple spots syndrome (MPSS) affecting the common Caribbean octocoral sea fan Gorgonia ventalina, linked to the gall-forming copepods of the genus Sphaerippe, a member of the widespread family Lamippidae. The specialized nature of these copepods as endoparasites in octocorals suggests the potential for the discovery of similar diseases across this host spectrum. Our investigation employed four molecular markers to study disease hotspots in Saint Eustatius, Curaçao, northwest and southwest Cuba, and Bonaire. This led to the discovery of a group of copepod species in these varied Caribbean locations. Importantly, these species are morphologically indistinguishable through traditional methods, challenging established taxonomic approaches. The observed diversity of symbionts, despite the host species' genetic uniformity, is likely due to variations in larval dispersal mechanisms. Our phylogenetic analyses confirmed that the Lamippidae copepods belong to the order Poecilostomatoida (Copepoda) and revealed their sister group relationship with the Anchimolgidae, Rhynchomolgidae, and Xarifiidae clades, known for their symbiotic relationships with scleractinian corals. These results add to our understanding of the evolutionary and ecological interactions of copepods and their hosts, and the diseases they cause, important data in a changing climate.

Predators are dependent on the capture of prey to meet their energetic and nutritive requirements, imposing a regime of predation risk. Consequently, prey experience both consumptive and non-consumptive effects. Non-consumptive effects may manifest through altered growth and ontogenetic trajectories of prey species, a dynamic modulated by olfactory or other sensory cues from predators. Bactrocera dorsalis Hendel represents a great invasive threat to global horticulture. While earlier research has primarily centered on the consumptive interactions between B. dorsalis and its natural enemies, the potential consequences of non-consumptive interactions on the development of B. dorsalis have been overlooked. In this study, we investigated the impact of predation risk effects, induced by both visual exposure to the predatory mantis Hierodula patellifera Serville and its associated odor, on the life history traits of B. dorsalis. Female B. dorsalis demonstrated reduced development time in the presence of isolated H. patellifera or H. patellifera odor, yet evidenced significantly increased fecundity. Conversely, males displayed no significant change in development time. Additionally, neither female nor male body weight at death was significantly influenced by predation risk from isolated predators or predator odor. These results indicated adaptive developmental strategies of B. dorsalis when faced with risks from predators and highlight the important role of predator odor, which has the potential to lay the groundwork for improving biological control efforts and innovative approaches within pest control.

Underwater image often exhibit detail blurring and color distortion due to light scattering, impurities, and other influences, obscuring essential textures and details. This presents a challenge for existing super-resolution techniques in identifying and extracting effective features, making high-quality reconstruction difficult. This research aims to innovate underwater image super-resolution technology to tackle this challenge. Initially, an underwater image degradation model was created by integrating random subsampling, Gaussian blur, mixed noise, and suspended particle simulation to generate a highly realistic synthetic dataset, thereby training the network to adapt to various degradation factors. Subsequently, to enhance the network's capability to extract key features, improvements were made based on the symmetrically structured Blind Super-Resolution Generative Adversarial Network (BSRGAN) model architecture. An attention mechanism based on energy functions was introduced within the generator to assess the importance of each pixel, and a weighted fusion strategy of adversarial loss, reconstruction loss, and perceptual loss was utilized to improve the quality of image reconstruction. Experimental results demonstrate that the proposed method achieved significant improvements in Peak Signal-to-Noise Ratio (PSNR) and Underwater Image Quality Measure (UIQM) by 0.85 dB and 0.19, respectively, significantly enhancing the visual perception quality and indicating its feasibility in super-resolution applications.

Co-integration and Causality was built to conduct studies on causality relation between carbon intensity and coal consumption leading to providing important basis for the transition to a low carbon economy. The EG two-step method was performed to study the relation between carbon intensity and coal consumption of China during 1990-2015 and the co-integration and Granger test was constructed to build up the co-integration and error correction models for analysis of the interaction between carbon intensity and coal consumption. The results showed that in long term there is a stable co-integration relation and a positive correlation between carbon intensity and coal consumption; whereas fluctuations exist in short term and there is a one-way Granger causality of carbon intensity with respect to coal consumption.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

We studied the effect of the structure parameters of engine annular cooling fan with outer ring on the aerodynamic performance by means of experiments and model simulation in fluent^®. Firstly, based on the experiment, a computational model is developed to calculate and analyze the aerodynamic performance of the tested annular fan. The model is validated by comparing the test results with the calculated data. Besides, the aerodynamic performance differences between two types of fans (common fan without outer ring and annular fan with outer ring) are discussed. Based on the computational model, the relation between aerodynamic performance and the outer ring structure parameters are investigated. The results show that the relative parameter on the axial direction has great influence on the aerodynamic performance; while the effect of radial relative parameter is minor. In addition, the outer ring with arc chamfer structure in the downstream side can improve its static pressure efficiency effectively.

In recent years, semantic communication has received significant attention from both academia and industry, driven by the growing demands for ultra-low latency and high-throughput capabilities in emerging intelligent services. Nonetheless, a comprehensive and effective theoretical framework for semantic communication has yet to be established. In particular, finding the fundamental limits of semantic communication, exploring the capabilities of semantic-aware networks, or utilizing theoretical guidance for deep learning in semantic communication are very important yet still unresolved issues. In general, the mathematical theory of semantic communication and the mathematical representation of semantics are referred to as semantic information theory. In this paper, we introduce the pertinent advancements in semantic information theory. Grounded in the foundational work of Claude Shannon, we present the latest developments in semantic entropy, semantic rate-distortion, and semantic channel capacity. Additionally, we analyze some open problems in semantic information measurement and semantic coding, providing a theoretical basis for the design of a semantic communication system. Furthermore, we carefully review several mathematical theories and tools and evaluate their applicability in the context of semantic communication. Finally, we shed light on the challenges encountered in both semantic communication and semantic information theory.

Plant height is significantly correlated with grain traits, which is a component of wheat yield. The purpose of this study is to investigate the main QTLs that control plant height and grain-related traits in multiple environments. In this study, we constructed a high-density genetic linkage map using the Wheat50K SNP Array to map quantitative trait loci (QTLs) for these traits in 198 recombinant inbred lines (RILs). The two ends of the chromosome were identified as re-combination-rich areas in all chromosomes except chromosome 1B. The middle area of the chro-mosomes was identified as the recombination-barren area. Both the genetic map and the physical map showed a significant correlation when p=0.001, with a correlation coefficient between 0.63 and 0.99. However, there was almost no recombination between 1RS and 1BS. In terms of plant height, 1RS contributed to the reduction of plant height by 3.43cm. In terms of grain length, 1RS contributed to the elongation of grain by 0.11mm. A total of 43 QTLs were identified, including 8 QTLs for Plant height(PH), 11 QTLs thousand grain weight(TGW), 15 QTLs for grain length(GL),and 9 QTLs for grain width(GW), which explained 1.36%–33.08% of the phenotypic variation. Seven were environment-stable QTLs, including two loci Qph.nwafu-4B and Qph.nwafu-4D that determined plant height. The explanation rates of phenotypic variation were 7.39%-12.26% and 20.11%-27.08%, respectively. One QTL, Qtgw.nwafu-4B, which influenced TGW, showed an explanation rate of 3.43%-6.85% for phenotypic variation, two co-segregating KASP markers were developed, the physical locations corresponding to KASP_AX-109316968 and KASP_AX-109519968 were 25.888344 MB and 25.847691 MB. Another QTL, Qgw.nwafu-4D, which determined grain width, had an explanation rate of 3.43%-6.85%. Three loci that affected the grain length were Qgl.nwafu-5A, Qgl.nwafu-5D.2 and Qgl.nwafu-6B, illustrating the explana-tion rates of phenotypic variation as 6.72%-9.59%, 5.62%-7.75%, and 6.68%-10.73%, respectively. Two QTL clusters were identified on chromosomes 4B and 4D.

3D object detection is essential for an accurate and reliable autonomous driving system. Currently, the methods used by the state-of-the-art two-stage detectors are not flexible enough and their fea-ture extraction capabilities are very limited to cope effectively with the disorder and irregularity of point clouds. In this paper, we combine the advantages of both PV-RCNN and PAConv (Position Adaptive Convolution) to create a completely new network, FANet, in order to overcome the ir-regularity and disorder of point clouds. The convolution in our network builds convolutional ker-nels from a basic weight matrix, whose combined coefficients are learned adaptively by LearnNet from relative points. This network allows for flexible modeling of complex spatial variations and geometric structures in the 3D point cloud, enabling better extraction of point cloud features and producing high-quality 3D proposal boxes. Compared to other methods, FANet is superior in terms of 3D object detection accuracy. Extensive experiments on the KITTI dataset have shown a signif-icant improvement in our approach.

The urban transportation network design problem involving exclusive bus lanes (XBLs) has been widely discussed and analyzed in recent years. An improved and more flexible transit lane management strategy—intermittent bus lanes (IBLs)—prove to be potentially more efficient and car-friendly than XBLs. The common benefit of XBLs and IBLs arises from the fact that they separate the bus and car traffic and hence can eliminate the impacts of slowly moving buses on the car traffic. This paper proposes a cell transmission model for separate car and bus traffic (CTM-SCB) in a network with some dedicated roadway segments reserved for buses. By encapsulating the CTM-SCB model, an XBL-based network design problem and an IBL-based network design problem are then formulated and solved, respectively, where the former model statically sets bus lanes while the later one allows a dynamic allocation of bus lanes. A synthetic freeway-arterial network and a real-world urban street network (where the latter was extracted from the Harbin South New Industrial City) are used as test networks for evaluating the proposed models and methods. The numerical results show that both XBLs and IBLs enjoy significant operational efficiency benefits compared to the situation of no protected bus lanes. However, we believe that the expected improvement from XBLs to IBLs need further tests and validations.

Resides derived from liquefaction of oil palm trunk in the presence of polyhydric alcohol with different liquefaction temperature and time were characterized to provide a new approach to understand some fundamental aspects of the liquefaction reaction. Higher temperature and longer reaction time resulted in lower residue content, indicating more decomposition of components of oil palm trunk. The amorphous polymer comprised of lignin, hemicellulose, starch, and cellulose with non-crystalline structure are firstly degraded at low liquefaction temperature, followed by the decomposition of crystalline region of cellulose. Although it was relatively difficult to destroy the ordered structure of cellulose, most of them could be liquefied via prolonging reaction time or enhancing reaction temperature. Nevertheless, it was found that re-condensation of liquefied products occurred during the liquefaction process when higher temperature of 180 oC was used after 60 min, leading to the gradual increase of residue content with increase of reaction time.

There is no doubt that seagrass beds constitute one of the most productive ecosystems in shallow coastal waters. Despite this, picoplankton in seagrass ecosystems has received relatively little attention. The purpose of this study was to compare picoplankton growth and mortality rates between seagrass and unvegetated habitats using chamber incubations. We tested two main hypotheses: (i) incubation with seagrass would result in higher bacterial growth rates due to increased DOM release from seagrass photosynthesis, and (ii) Synechococcus spp. would be lower in the presence of seagrass due to competition for inorganic nutrients. Our results showed bacterial growth rates of 2.31 and 2.44 d–1 without and with seagrass, respectively. In seagrass chambers, bacterial growth was higher than that in non-seagrass chambers, suggesting that organic carbon coming from the seagrass community may support bacterial production. Furthermore, we observed a negative Synechococcus spp. growth rate (-0.9 d–1) in the seagrass treatment, likely reflecting nutrient competition with the seagrass. Small-scale chambers proved to be a useful tool for studying the factors controlling spatial and temporal patterns of picoplankton across different habitats. Furthermore, future studies should examine picoplankton growth over a wider range of spatial scales in seagrass beds and adjacent unvegetated sediment.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.

A class of semi-linear elliptic equations with critical Hardy-Sobolev exponent has been considered. This model is widely used in hydrodynamics and glaciology, gas combustion in thermodynamics, quantum field theory and statistical mechanics, as well as gravity balance problems in galaxies. The $\left( PS\right) _{c}$ sequence of energy functional has been investigated, and then the mountain pass lemma was used to prove the existence of at least one nontrivial solution. Also a multiplicity result has been obtained. Some known results have been generalized.

In this paper, a class of semi-linear elliptic equations involving Hardy-Sobolev critical exponents has been investigated. This problem comes from the consideration of standing waves in the anisotropic Schr\"{o}dinger equation, also it is very important in the field of hydrodynamics, glaciology, quantum field theory and statistical mechanics. By a detailed estimation for the extremum function and using Mountain Pass Lemma with $\left( PS\right) _{c}$ conditions, the existence of positive solutions has been obtained. On the other hand, by establishing Pohozaev-type identity and using the properties of Bessel function, the nonexistence of positive solution also has been obtained. These results are extensions of E. Jannelli's research (\cite[Theorem 1.A-1.C]{EJ}).

With the rapidly increasing of people’s purchasing power, the fast moving consumer goods (FMCG) industry is supposed to grow dramatically. In order to gain more market access and profile, it is important for the FMCG manufacturers and retailers to find the preferences and provincial characteristics of consumers, to develop more suitable goods distribution strategy. Based on retails marketing data with geographic characteristics, this paper proposes a new combination of geography methods to solve the problems in distribution of FMCG. Via multiple K-means clustering and cross validation of KNN half off, the mesoscopic sales features are extracted through the classification of retails, which can indirectly grasp the consumer behavior characteristics. Based on space division and Moran’ I spatial autocorrelation arithmetic, two strategies are developed to satisfy consumer’s needs and promote sales, including conservative and positive strategies. According to our analysis, the total sales volume of the regions will increase by 5.1% and 10.3%. This study can be applied to the provide purchase strategies for FMCG retails according to their locations. The research can explore the consumption potential of different areas, thus improving the profile of retails and the development of economy in more mesoscopic scale.

Tulou dwellings in Southeast China have captivated global interest due to their distinctive appearance, sustainable construction materials and technologies, and their defensive and collective housing functions. Despite several recognized as World Cultural Heritage sites, the vast majority of tulou buildings are undergoing irreversible decline and destruction, necessitating a comprehensive and systematic study. Taking 83 Tulou buildings in Raoping County, Chaozhou City, Guangdong Province as the research object, this study reconstructs the historical scenes and systematically reveals the emergence, popularity, and consolidation process of tulou dwellings as integrated defensive and residential buildings for ordinary people by conducting a comprehensive analysis of historical documents and local chronicles. Based on an extensive field investigation, the study systematically analyzes the geospatial distribution and the spatial characteristics of Raoping tulou and its residential unit. The results demonstrate the adaptability and flexibility of tulou dwellings, showcasing their developmental process and revealing the inclusive nature of these traditional residences, as well as the initiative of those who reside within them. The research findings contribute to a more dynamic, comprehensive, and authentic understanding of tulou and Chinese traditional residences, providing valuable references for the preservation and sustainable development of tulou architectural heritage.

In this paper, we propose a partial differential equation model based on phase-field for sentiment analysis in the field of hotel comment texts. The comment texts are converted into word vectors using the Word2Vec tool, and then we utilize the multifractal detrended fluctuation analysis (MF-DFA) model to extract the generalized Hurst exponent of the word vector time series to achieve dimensionality reduction of the word vector data. The dimensionality reduced data is represented in a two-dimensional computational domain, and the modified Allen-Cahn (AC) function is used to evolve the phase values of the data to obtain a stable nonlinear boundary, thereby achieving automatic classification of hotel comment texts. The experimental results show that the proposed method can effectively classify positive and negative samples and achieve excellent results in classification indicators. We compared our proposed classifier with traditional machine learning models and the results indicate that our method possesses a better performance.

In the current study, a two-dimensional numerical study is carried out to investigate the performance of a novel Double-chamber Parallel Flexible Valves micropump, which utilized the electrowetting-on-dielectrics (EWOD) effect to drive the microfluid flow. By observing the flow fields, the internal circulations are seen on both the left and right side of the pump. The generation of the backflow is discussed by tracking the movement of the vortices. Only slight flow fluctuation is seen in the micropump. Based on the simulation outcomes, the structural parameters including the width of the inlet/outlet, the width of the pumping channel and the diverging angle in the micropump are analyzed, the influence of these parameters on the pumping volume and the maximum pressure have been discussed. Eventually, a group of optimal parameter combinations is given according to the results to extend the operating potential of the micropump.

Affective prosody is an indispensable cognitive cue that moderates social activities, and has become a prevailing research topic in psychology-related disciplines. The present study conducts the first bibliometrics-based visualization analysis concerning affective prosody to evaluate the influential cases, including countries/regions, institutions, publication venues, academic articles, and disciplinary contributions, and the diachronic changes of publication trends and research hotspots. With the combination of statistical results and a qualitative literature inspection, limitations of extant studies and promising research directions were also proposed. The present study extracted the bibliographic data of 1,624 articles retrieved from the Web of Science Core Collection, which were published over the past 25 years (1997-2021). Statistical results revealed four leading powers (the U.S., Germany, England, and Canada) and four emerging fronts (China, France, Netherlands, and Switzerland), and identified three primary research themes in this field, including clinical implication, measurable index, and modality-specific issues. Literature inspection demonstrated current limitations in individual characteristics control and experiment-related influential factors, and proposed two prosperous research directions. Findings of the present study could facilitate academic retrieval of affective prosody research, help concerned researchers identify thematic hotspots and seek appropriate collaboration, and provide convenience for research policy and management in this field.

Tengchongite is a uranyl molybdate uranium mineral and it was found and named by Chen 1985.No more scholars studied on tengchongite after Chen’s work, The identification of this mineral has only been confirmed by single crystal X-ray diffraction. In the paper, micro laser Raman spectroscopy and infrared spectroscopy are used to identify the spectroscopy properties of tengchongite. The studies fill in the gaps of more than 30 years in terms of the molecular spectroscopy research of tengchongite. The mineral has an ideal model of Ca(UO₂)₆(MoO₄)₂O₅•12H₂O its bands attributed to the vibrating units are clearly identified in the Raman spectrum. Symmetric stretching modes at 812 cm^-1 and 839 cm^-1 are assigned to ν1 (UO₂)²⁺ ,The ν3 antisymmetric stretching modes of (UO₂)²⁺ are observed at 896 cm^-1, Symmetric stretching modes at 419^-1 and 440 cm^-1 are assigned to ν2 (UO₂)²⁺ .Symmetric stretching modes at 919cm-1 are assigned to ν1(MoO₄)^2-,The ν3 antisymmetric stretching modes of (MoO₄)^2- are observed at 752 cm^-1, the in-plane ν2(MoO₄)^2-and the out-of-plane ν4(MoO₄)^2- bending modes are at 169 cm^-1 and 254 cm^-1. IR spectrum of tengchongite shows the major uranyl band at 858 cm^-1 and 693 cm^-1, Mo-O bonds are observed at about 985 cm^-1 and 780 cm^-1, and H₂O groups are present with a wide range peaks from 3100 cm^-1 to 3500 cm^-1 and 1647 cm^-1, and the band at 1432.4 cm^-1 is probably due to the stretching vibration hydroxyl (OH^-1), therefore, tengchongite contains may include hydroxyl and its chemical formula needs to be modified .