In recent years, the AHRS has become an important research area. In order to improve the orientation measurement accuracy of AHRS, this paper first expounds the algorithm principle of the AHRS. Then, aiming at the problem of poor stability of the traditional gradient descent method under high dynamics or large magnetic field interference, a gain-scheduled anti-interference AHRS orientation algorithm is designed. By using the switching architecture designed with this algorithm for gain scheduling, it can ensure stable performance while being subjected to apparent acceleration and ferromagnetic interference. Finally, experimental verification is conducted, and the experimental results show that: in the presence of interference, the roll angle error is 0.0350°, the pitch angle error is 0.0277°, and the yaw angle error is 0.9611°, thereby verifying the strong anti-interference performance of the gain-scheduled AHRS orientation algorithm proposed in this paper.

The twisted Wang transform distribution family, defined as the composition of parameter shifted inverse CDF function with an original CDF function, is found to be most suitable for matching low shape factor distributions, characterizing hard to fit or to simulate reinsurance portfolio losses for some perils from our previous study. Among them, the best form for matching a hard-to-fit empirical loss distribution for a specific peril, is the Exponential Fractional Extra Power 0 Distribution in (0,1) with CDF:.The simplest yet still a good form of this family is the Transformed Hyperbolic Tangent Distribution with CDF:,which has analytical formulas for the moments. The twisted Wang transform distribution family is compared and confirmed to be superior to all other well-known distribution families through extensive numerical optimization practice, distribution forms guesses, and computer-aided exploration experiments.

Epoxy powders offer a low-cost means of manufacturing thick section composite parts, such as those found in wind and tidal turbines. Currently, their processing cycle includes a lengthy drying stage (≥ 15 h) to remove ambient moisture. This prevents void defect formation and, thereby, a reduction in mechanical properties, however, it constitutes up to 60% of the processing time. Little research has been published on the study of this process or its optimisation. Experimental and simulated analyses are used to investigate the effects of hygroscopicity in epoxy powder composites. In particular, focus is given to the drying process, which is used to prevent void defect formation and, thereby, a reduction in mechanical properties. As such, tests are performed to quantify the void content of dried and undried laminates, and to measure its impact on transverse flexural strength. Dynamic vapour sorption analysis is used to study the sorption behaviour of the epoxy powder. Sorption data is fitted to a modified linear driving force model, and then implemented in existing process simulations tools. The drying of a thick epoxy powder composite section is simulated to investigate the influence of powder sintering on the duration required for drying. It is shown that the epoxy powder is slightly hygroscopic (1.36 wt%) and exhibits sorption behaviour that is characteristic of glassy polymers. This results in up to 4.8% voids (by volume) if processed in an undried state, leading to a 43% reduction in transverse flexural strength. Process simulations reveal that a standard drying cycle prematurely sinters the powder; inhibiting moisture release. By maintaining a powder state, simulations show that the drying cycle can be reduced to 5 h.

To prepare an edible coating with a good preservative effect on sweet cherries, carboxymethyl chitosan (CMCS) and gelatin (GL) were selected as the film-forming matrix in this experiment, and CaCl2 and ascorbic acid (AA) were added as crosslinking agents and antioxidants, respectively. First, the film was prepared by the casting method, and the film formula with better mechanical and barrier performance was filtered out by one-factor and response surface optimization test, and the differences in the preservation effect of different film formulations (CMCS-GL, CaCl2- CMCS-GL, AA -CaCl2- CMCS-GL) on sweet cherries were compared. and then the different film formulations were compared. The difference in film formulation on the preservation effect of sweet cherries was investigated. The results showed that the optimal formulation for an edible film based on CMCS-GL with good performance was CMCS: GL (w:w)=2:1, with the additional amount of 1% glycerol, 2% CaCl2, 0.1% Tween-20, 2% AA, the tensile strength, elongation at break, oxygen permeability and water vapor permeability of the film obtained with this formula were: 16.28 MPa, 71.46%, 1.39×10-12 g- cm/(cm2-s-Pa), 5.10×10-11 cm3-cm/(m2-s-Pa), respectively. In the preservation of sweet cherries, all three film formulations effectively reduced the rotting rate and weight loss during storage while preserving the high hardness and skin color of the fruit. Among them, the formulation AA -CaCl2- CMCS-GL showed the best preservation effect and can be used as a new method for postharvest preservation of sweet cherries.

In this paper, the Fourier-based synchrosqueezing transform (FSST) method is introduced into the power system to realize low frequency oscillation identification. Firstly, the modal components of low frequency oscillation signal are separated by FSST, and calculating the instantaneous parameters including magnitude, frequency and phase of every mode component with Hilbert transform. Then , calculating the damping ration of every modal component based on above parameters and derived the formulas. Thus, it realized effective identification of of modal parameters of low frequency oscillation signal. The experimental results of simulated data and 16-generator system demonstrate the validity and correctness of the FSST method. Comparing with the classical Prony method shows that the FSST method is better in the identification accuracy when the low frequency oscillation signal is polluted by noise. Finally, the effectiveness of the FSST in Actual power grid is verified based on the real data from Sichuan power grid.

Aiming at the removal of radioactive cobalt ions from water by graphene oxide (GO), the adsorption mechanism of Co2+ on graphene oxide was analyzed using the quantum chemical calculation software Gaussian 16 based on the density functional theory. The influence of material structure factors such as carboxyl group, hydroxyl group, epoxy group and graphene sheet as well as external environmental factors such as pH, temperature and interfering ions on the adsorption effect was determined, and the influence of external environment was verified through experiments. Through calculation and experiment, it was found that the existence of oxygen-containing functional groups on graphene oxide can improve the adsorption efficiency of the materialappropriately,and increasing pH under acidic conditions was also helpful to improve the adsorption effect, and the material had certain selectivity for Co2+, the adsorption capacity and selectivity could be further improved when it was modified by increasing hydroxyl group.

Recently, the phase-sensitive OTDR (Φ-OTDR) based vibration sensor system has gained the focus of many researchers and some efforts have been undertaken to push further the limitations imposed on the performance of the Φ-OTDR sensor system. Then, progress in the different areas of its performance evaluation factors such as: improvement of the signal-to-noise ratio (SNR), spatial resolution (SR) in the sub-meter range, enlargement of the sensing range, frequency response bandwidth over the conventional limit and phase signal demodulation for quantitative measurement have been realized. This paper presents an overview of the recent progress in the Φ-OTDR based vibration sensing system in the different areas mentioned above.

A large number of studies have concluded that since housing pressure will affect the mobility of highly skilled young migrants (HSYM) in Chinese cities and regions, it is necessary to apply corresponding housing policies to adjust housing unaffordability for HYSM. This study uses a survey data conducted in China's Zhejiang Province of China, where specific policies have been implemented to attract talent and found that housing does crowds out the HSYM from a city, but the HSYM who have a master's degree or above or who work in government organizations or state-owned enterprises are more tolerant of housing unaffordability. The unmarried or those staying in the city for a long period are less tolerant of housing unaffordability. Meanwhile, there are the heterogeneous impacts of factors on the HSYM's tolerance for housing unaffordability across cities of different levels. Therefore, housing policies should highlight urban differences and intra-group differences.

The synchronous generator, as the main component of power systems, plays a key role in these system’s stability. Therefore, utilizing the most effective control strategy for modeling and control the synchronous generator results in the best outcomes in power systems’ performances. The advantage of using a powerful controller is to have the synchronous generator modeled and controlled as well as its main task i.e. stabilizing power systems. Since the synchronous generator is known as a complicated nonlinear system, modeling and control of it is a difficult task. This paper presents a sum of squares (SOS) approach to modeling and control the synchronous generator using polynomial fuzzy systems. This method as an efficacious control strategy has numerous superiorities to the well-known T–S fuzzy controller, due to the control framework is a polynomial fuzzy model, which is more general and effectual than the well-known T–S fuzzy model. In this case, a polynomial Lyapunov function is used for analyzing the stability of the polynomial fuzzy system. Then, the number of rules in a polynomial fuzzy model is less than in a T-S fuzzy model. Besides, derived stability conditions are represented in terms of the SOS approach, which can be numerically solved via the recently developed SOSTOOLS. This approach avoids the difficulty of solving LMI (Linear Matrix Inequality). The Effectiveness of the proposed control strategy is verified by using the third-part Matlab toolbox, SOSTOOLS.

Strigolactones (SLs) are a novel emerging plant hormones, which play important roles in regulating plant organ development and environmental stress tolerance. Even though the SL related genes have been identified and well characterized in some plants. The information of SL related genes in soybean is not fully established yet, especially in response to salt stress. In this study, we identified nine SL biosynthesis genes: two D27, two CCD7, two CCD8, and three MAX1, and seven SL signaling genes: two D14, two MAX2 and three D53 in soybean genome. We found that SL biosynthesis and signaling genes are conserved during evolution in different species. Syntenic analysis of these genes revealed their location on nine chromosomes as well as existence of ten pairs of duplication genes. Moreover, plant hormone and stress-responsive elements were identified in the promoter regions of SL biosynthesis and signaling genes. By using quantitative real-time PCR (qRT-PCR), we confirmed that SL genes have different tissue expression in roots, stems and leaves. Further, we also explored the expression profiles of SL biosynthesis and signaling genes under salt stress. These results suggested that SL signaling genes may play important regulatory roles in response to salt stress. In conclusion, we identified and provided valuable information on the soybean SL biosynthesis and signaling genes, and established a foundation for further functional analysis of soybean SL related genes in response to salt stress.

The base excitation of mechanical equipment can result in pipeline system vibration which seriously affects the safe operation of the equipment. Particle damping technology is based on the particle collision dissipation principle to realize the structural vibration energy dissipation. This paper introduces the particle damping method into the vibration control of pipeline system. A particle damper has been designed for the structural characteristics of the pipeline. The influence of the material and structure of the pipeline particle damper, the external excitation and other parameters on the energy dissipation characteristics of particle damping are revealed. The energy dissipation mechanism of the pipeline particle collision damper under various parameter is analyzed. A pipeline vibration reduction test system with particle damping has been established. The effects of different excitation conditions, damper materials and number of unit structures of particle damper on the vibration damping effect of pipeline systems are investigated comparatively. The influence of damper parameters on the vibration suppression of pipeline system is obtained. The research in this paper can provide technical references for vibration suppression of pipeline systems.

Transcription factors (TFs) are crucial in modulating gene expression and sculpting cellular and organismal phenotypes. The identification of TF-target gene interactions is pivotal for comprehending molecular pathways and disease etiologies but has been hindered by the demanding nature of traditional experimental approaches. This paper introduces a novel web application, utilizing the R programming language, which predicts TF-target gene relationships and vice versa. Our application integrates the predictive power of various bioinformatic tools, leveraging their combined strengths to provide robust predictions. It merges databases for enhanced precision, incorporates gene expression correlation for accuracy, and employs pan-tissue correlation analysis for context-specific insights. The application also enables the integration of user data with established resources to analyze TF-target gene networks. Despite its current limitation to human data, it provides a platform for exploring gene regulatory mechanisms comprehensively. This integrated, systematic approach offers researchers an invaluable tool for dissecting the complexities of gene regulation, with the potential for future expansions to include a broader range of species.

We explored the dynamics of the two interacting information systems. We show that for the Markovian marginal systems the driving force for information dynamics is determined by both the information landscape and information flux. While the information landscape can be used to construct the driving force to describe the equilibrium time reversible information system dynamics, the information flux can be used to describe the nonequilibrium time-irreversible behaviours of the information system dynamics. The information flux explicitly breaks the detailed balance and is a direct measure of the degree of the nonequilibriumness or time irreversibility. We further demonstrate that the mutual information rate between the two subsystems can be decomposed into the equilibrium time-reversible and nonequilibrium time-irreversible parts respectively. This decomposition of the mutual information rate (MIR) corresponds to the information landscape-flux decomposition explicitly when the two subsystems behave as Markov chains. Finally, we uncover the intimate relationship between the nonequilibrium thermodynamics in terms of the entropy production rates and the time-irreversible part of the mutual information rate. We found that this relationship and MIR decomposition still hold for the more general stationary and ergodic cases. We demonstrate the above features with two examples of the bivariate Markov chains.

The need for cross-modal retrieval (CMR) among users is growing because of the swift advancements in computer vision and natural language processing. Promoting home operating systems is greatly aided by the openKylin home operating system. It is focused on enhancing the functionality of the operating system with safe and dependable operating technologies. Practical implications abound for integrating computer vision research into home operating systems. A multimodal retrieval approach based on openKylin is presented to improve the usability of text search graphs, audio, and video. The overview of pertinent domestic and international research is the main topic of this article. This technological advancement. It then offers details on the design, implementation procedure, and final implementation outcomes for demonstration. The works of natural operations show that this strategy has excellent accuracy and performance.

An efficient stereoselective three-component reaction for the synthesis of spiro[4H-chromene-3,3’-oxindole] derivatives was realized through an organocatalyzed cascade Knoevenagel/Michael/cyclization reaction using a quinidine-derived squaramide as the catalyst. Under the optimized conditions, the reactions of isatins, malononitrile, and sesamol yield the desired spirooxindoles in good yields (75–87%) and moderate to high ee values (up to 90% ee). Two pairs of selected enantiomers were subjected to evaluate their antiproliferative activities on three types of human cancer cell lines using the MTT assay. The results indicated that stereoselectivity and electrical effect showed significant impact on activity. Enanotiomer R-3f exhibited optimal cytotoxic activity against U2OS cell line, which was close to the inhibitory activity of positive control, Adriamycin.

Mulberry is an economically significant crop for the sericulture industry worldwide. Stresses such as drought exposure have a significant influence on plant survival. Metabolome directly reflects plant physiological status; thus, a way to assess this impact is to perform a global metabolomic analysis. This study investigated the effect of drought stress on mulberry Yu-711 metabolic balance using a liquid chromatography-mass spectrometry (LC-MS) based on an untargeted metabolomic approach. For this objective, Yu-711 leaves were subjected to two weeks of drought stress treatment and control without drought stress. Multivariate and univariate statistical analyses highlighted numerous differentially-accumulated metabolic elements as a function of time and treatment. Drought stress led to a more differentiated metabolites response than the control. We found that the levels of total lipids and galactolipids, and phospholipids (PC, PA, PE) were significantly altered, producing 48% of the total differentially expressed metabolites. Fatty acyls were the most abundant lipids expressed and decreased considerably by 73.6%. Prenol lipids class of lipids increased in drought leaves. Other classes of metabolites, including polyphenols( flavonoids and cinnamic acid), organic acid (amino acids), carbohydrates, benzenoids, and organoheterocyclic, all had a dynamic trend in response to the drought stress. However, their levels under drought stress generally decreased significantly compared to the control. These results provide an overview of the metabolic profile of the mulberry plant through differentially-accumulated compounds and provide a better understanding of global plant metabolic changes in defense mechanisms.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

In this paper, the experimental study of heating in 2 h lunch mode of air-conditioned bed system is carried out. The results show that the power consumption of heat conduction heating is only 0.34 kW·h, and the average heat dissipation is 81.3 W, while the power consumption of convection heating is 1.43 kW·h, with an average heat dissipation of 748.7 W. Regardless of power consumption or heat dissipation, convection heating is significantly higher than heat conduction heating, resulting in the room air temperature of the former increased from 12.3 °C to 17.3 °C, while the latter only increased from 14.4 °C to 15.2 °C. The study found that the water temperature of heat conduction heating can meet the thermal comfort needs of the human body in the range of 38~40 °C, while convection heating requires a higher temperature range, In contrast, the grade of hot water required for heat conduction heating is lower. Through the experiment, it is also found that the temperature of convection heating rises fast, but it is easy to appear dry feeling after a long time, while heat conductive heating has a slow temperature rise. there is a cool feeling within 20 min after the heating starts, and then the thermal comfort is better. The air conditioning system in this paper is used for the heating experiment in the winter lunch break mode, compared with convection heating, the overall thermal comfort of heat conduction heating is better and more energy efficient. it is suggested to adopt heat conduction heating mode in the winter heating of this system.

The pathogenicity of grapevine geminivirus A (GGVA), a recently identified DNA virus, to grapevine plants remains largely unclear. Here, we report a new GGVA isolate (named GGVAQN) obtained from grapevine ‘Queen Nina’ plants with severe disease symptoms; the infectious clone of GGVAQN (pXT-GGVAQN) was also constructed. Infection assays indicated that Nicotiana benthamiana plants inoculated with GGVAQN display upward leaf curling and chlorotic mottling symptoms. Direct injection of Agrobacterium tumefaciens cells carrying pXT-GGVAQN into roots of in vitro-grown ‘Red Globe’ grape plantlets by syringe led to systemic infection with GGVAQN, and the plants exhibited chlorotic mottling symptoms on their upper leaves, and downward curling, interveinal yellowing, and leaf-margin necrosis symptoms on their lower leaves. Our results provide insights into the pathogenicity of GGVA, and a simple and efficient inoculation method to deliver infectious viral clones to woody perennial plants.

Glass has emerged as a highly versatile substrate for various sensor and MEMS packaging applications, including electromechanical, thermal, optical, biomedical, and RF devices, due to its exceptional properties such as high geometrical tolerances, outstanding heat and chemical resistance, excellent high-frequency electrical properties, and the ability to be hermetically sealed. In these applications, Through-Glass-Via (TGV) plays a vital role in manufacturing and packaging by creating electrical interconnections through glass substrates. This paper provides a comprehensive summary of the research progress in TGV fabrication along with their integrations, including through-via formation and metallization. The paper also reviews the significant qualification and reliability achievements obtained by the scientific community for TGV. Additionally, the paper summarizes the application of TGV technology in various sensors.

The author’s opinion is that the negative energy solutions of the Dirac equation mean that a particle can be of negative kinetic energy (NKE) besides positive kinetic energy (PKE). We think that NKE particles are dark ones and NKE matter is dark matter. In our previous works, the dark matter theory of the NKE version and the dark energy theory that matched dark matter theory were put forth. In this work, we investigate the topics related to the metamorphosis of objects between PKE and NKE. We first evaluate the collosions between a PKE and a NKE particles. A scenario of accelerating PKE particles is raised. We put forth the cosmic dark radiation background and gravity potential background. In the universe, negative energy is predominating. In the observable universe, substances constitute stable PKE systems. The total energy of every such system is negative. We propose a mechanism that NKE substances combine into stable PKE systems. Macroscopically, NKE objects can constitute stable PKE astrophysical systems by means of gravity between them. Microscopically, NKE particles can combine into stable PKE systems by means of attractive interactions between them, say, Coulomb attraction. Currently, people think that there are four ingrediants in the universe: photons \Omega_R0, matter \Omega_M0, dark matter \Omega_DM, and dark energy \Omega_\lambda0. We analyze the order of the appearance of the four ingredients and conclude that qualitatively, their proportions should be \Omega_\lambda0 > \Omega_DM > \Omega_M0 > \Omega_R0.

L-Theanine, a unique non-protein amino acid, is an important bioactive component of green tea. Previous studies have shown that L-theanine has many potent health benefits, such as anti-anxiety effect, regulation of immune response, relaxing neural tension, reducing oxidative damage. However, little is known concerning whether L-theanine can improve the clearance of mitochondrial DNA (mtDNA) damage in organisms. Here, we reported that L-theanine treatment increased ATP production and improved mitochondrial morphology to extend the lifespan of UVC-exposed nematodes. Mechanistic investigations showed that L-theanine treatment enhanced the removal of mtDNA damage and extended lifespan by activating autophagy, mitophagy, mitochondrial dynamics, and mitochondrial unfolded protein response (UPRmt) in UVC-exposed nematodes. In addition, L-theanine treatment also up-regulated the expression of genes related to mitochondrial energy metabolism in UVC-exposed nematodes. Our study provided a theoretical basis for the possibility that tea drinking may prevent mitochondrial related diseases.

Dissolved organic matter (DOM) derived from organic fertilizers may increase soil phosphorus (P) availability. However, the frequently observed correlation between soil P availability and dissolved organic carbon (DOC) content has led to an excessive focus on DOC content at the expense of DOM properties. The present study investigated the influence of DOM characteristics on soil P availability by using a 6-year field experiment and microcosms of P sorption in paddy soil. Our results showed that partial replacement of chemical P fertilizer with manure or crop straw increased P fertilizer-use efficiency, even when decreasing chemical P input by 34 %, compared to normal chemical fertilization. The microcosm experiment demonstrated that DOM properties, rather than total DOC content, determine soil P sorption capacity, despite the significant correlation between DOC content and P availability observed in the field experiment. Manure-DOM exerted stronger inhibitory effects on P sorption than straw-DOM, and high molecular weight (HMW)-fractionated DOM exerted stronger inhibitory effects on P sorption than low-molecular-weight-fractionated DOM by 16-20%. The mechanism was rooted in the HMW DOM with unique characteristics (e.g., strong aromaticity, hydrophobicity, abundant humic-like components, carboxyl groups, and benzene ring structures) competing for soil P sorption sites (e.g., reduction in specific surface area and micropore volume), decreasing the soil surface charge (e.g., zeta potential), and thereby suppressing P sorption in paddy soil. Our study points out a promising avenue for regulating organic matter properties with organic fertilization to improve P use efficiency in agricultural soils.

Spatial crowdsourcing emerges as a new computing paradigm that enables mobile users to accomplish spatio- temporal tasks in order to solve human-intrinsic problems. Existing crowdsourcing systems critically use centralized servers for interacting with workers and making task assignment decisions. These systems are hence susceptible to issues such as the single point of failure and the lack of operational transparency. Prior work, therefore, turns to blockchain-based decentralized crowdsourcing systems, yet still suffers from problems of lacking efficient task assignment scheme, requiring a deposit to an untrusted system, low block generation speed, and high transaction fees. To address these issues, we design a blockchain-based decentralized framework for spatial crowdsourcing, which we call SC-EOS. Our system does not rely on any trusted servers, while providing efficient and user-customizable task assignment, low monetary cost, and fast block generation. More importantly, it frees users from making a deposit into an untrusted system. Our framework can also be extended and applied to generic crowdsourcing systems. We implemented the proposed system on the EOS blockchain. Trace-driven evaluations involving real users show that our system attains the comparable task assignment performance against a clairvoyant scheme. It also achieves 10× cost savings than an Ethereum-based implementation.

Regeneration of biological tissues in medicine is challenging, and 3D bioprinting offers an innovative way to create functional multicellular tissues. One common way in bioprinting is bioink which is one type of the cell-loaded hydrogel. For clinical application, however, the bioprinting still suffers from satisfactory performance, e.g. in vascularization, effective antibacterial, immunomodulation and regulation of collagen deposition. Many studies have incorporated different bioactive materials into the 3D printed scaffolds to optimize the bioprinting. Here, we review a variety of additives added to the 3D bioprinting hydrogel. The underlying mechanisms and methodology for biological regeneration are important and will provide useful basis for future research.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

Reinforcement Learning (RL) has demonstrated considerable potential in solving challenges across various domains, notably in autonomous driving. Nevertheless, implementing RL in autonomous driving comes with its own set of difficulties, such as the overestimation phenomenon, extensive learning time, and sparse reward problems. Although solutions like Hindsight Experience Replay (HER) have been proposed to alleviate these issues, the direct utilization of RL in autonomous vehicles remains constrained due to the intricate fusion of information and the possibility of system failures during the learning process. In this paper, we present a novel RL-based autonomous driving system technology that combines Obstacle Dependent Gaussian (ODG) RL, Soft Actor-Critic (SAC), and meta-learning algorithms. Our approach addresses key issues in RL, including the overestimation phenomenon and sparse reward problems, by incorporating prior knowledge derived from the ODG algorithm. We evaluated our proposed algorithm on official F1 circuits, using high-fidelity racing simulations with complex dynamics. The results demonstrate exceptional performance, with our method achieving up to 89% faster learning speed compared to existing algorithms in these environments.

For solving the fractional differential equations in computational fluid dynamics (CFD), it’s complicated and difficult by the Laplace and Fourier transforms. Based on the Caputo fractional derivative, the analytical solutions for unsteady unidirectional flows of a generalized Oldroyd-B fluid are deduced by the separation of variables method. Results show that the analytical solutions are given easily, and have good university. For some specific parameter values, the well-known analytical solutions for the generalized second grade fluid, the generalized Upper-Convected Maxwell (UCM) fluid as well as the ordinary Oldroyd-B fluid can be obtained.

The phenomenon of interference is a characteristic of all waves. This paper reviews the interference of classical waves and of matter waves in quantum mechanics. In quantum mechanics, there are two interference mechanisms between identical particles. One is that the de Broglie wavelengths of two interference waves are the same, which is called the equal wavelength interference mechanism. The other is that the wavelengths of interference waves can also be different, in which case there should be an exchange term in additional to the direction term in the wave function. There is a fixed phase difference between the two terms, which causes interference. This is called exchange effect interference mechanism. We propose an experiment, which is simpler to what has been done, to show the exchange effect interference. There is a special case where two interference waves can satisfy both the two mechanisms. We propose an experiment to discriminate that in this case which mechanism plays a role on earth.

People have long had a problem: the equations of motion that reflect the laws of physics are invariance under time inversion, while there always are irreversible processes for gases compose of microscopic particles. This article solves this problem. The point is that we should distinguish between the concepts of the equation of motion and motion. We also need to distinguish between the concepts of time-inverse motion and reverse motion. The former is anticlockwise, which is a frictional motion, while the latter is clockwise. For the single-particle motions in classical mechanics and in quantum mechanics, we present mathematical expressions for time-inversion motion and reverse motion, respectively. We demonstrate that single-particle motion is irreversible. The definition of the reversibility of two-particle collisions is given. According to the definition, the two-particle collision as a microscopic motion processes is irreversible. Consequently, for a gas consisting of a large number of particles colliding with each other, its movement should be irreversible, unless the condition of detailed balance is met. We give a physical explanation for the detailed balance, which does not concern the meaning of microscopic reversibility. The detailed balance means that after a pair of reciprocal collisions occur, the distribution function of the particles remains unchanged. Therefore, microscopic two-particle collision events are irreversible, but the statistical average of a large number of collision events makes it possible for the macroscopic process of a gas to be reversible. Conclusively, we clarify the microscopic mechanism of the irreversible process of gases.

Up to now, Schrödinger equation, Klein-Gordon equation (KGE) and Dirac equation are believed the fundamental equations of quantum mechanics. Schrödinger equation has a defect that there is no NKE solutions. Dirac equation has positive kinetic energy (PKE) and negative kinetic energy (NKE) branches. Both branches should have low momentum, or nonrelativistic, approximations: one is Schrödinger equation and the other is NKE Schrödinger equation. KGE has two problems: it is an equation of second time derivative, and calculated density is not definitely positive. To overcome the problems, it should be revised as PKE and NKE decoupled KGEs. The fundamental equations of quantum mechanics after the modification have at least two merits. They are of unitary in that everyone contains the first time derivative and are symmetric with respect to PKE and NKE. This reflects the symmetry of the PKE and NKE matters, as well as matter and dark matter, of our universe. The problems of one-dimensional step potentials are resolved by means of the modified fundamental equations for a nonrelativistic particle.

Goal-conditioned reinforcement learning (RL) holds promise for addressing intricate control challenges by enabling agents to learn and execute desired skills through separate decision modules. However, the irregular occurrence of required skills poses a significant challenge to effective learning. In this paper, we demonstrate the detrimental effects of this imbalanced skill(sub-goal) distribution and propose a novel training approach, Classified Experience Replay (CER), designed to mitigate this challenge. We demonstrate that adapting our method to conventional RL methods significantly enhances the performance of the RL agent. Considering the challenges inherent in tasks such as driving, characterized by biased occurrences of required sub-goals, our study demonstrates the improvement in trained outcomes facilitated by the proposed method. In addition, we introduce a specialized framework tailored for self-driving tasks on highways, integrating Model Predictive Control (MPC) into our RL trajectory optimization training paradigm. Our approach, utilizing CER with the suggested framework, yields remarkable advancements in trajectory optimization for RL agents operating in highway environments.

COVID-19 patients can recover with a median SARS-CoV-2 clearance of 20 days post initial symptoms (PIS). However, we observed some COVID-19 patients with existing SARS-CoV-2 for more than 50 days PIS. This study aimed to investigate the cause of viral clearance delay and the infectivity in these patients. Demographic data and clinical characteristics of 22 long-term COVID-19 patients were collected. SARS-CoV-2 nucleic acid, peripheral lymphocyte count, and functionality were assessed. SARS-CoV-2-specific and neutralization antibodies were detected, followed by virus isolation and genome sequencing. The median age of the studied cohort was 59.83±12.94 years. All patients were clinically cured after long-term SARS-CoV-2 infection ranging from 53 to 112 days PIS. Peripheral lymphocytes counts were normal. Interferon gamma (IFN-ƴ)-generated CD4+ and CD8+ cells were normal as 24.68±9.60% and 66.41±14.87%. However, the number of IFN-ƴ-generated NK cells diminished (58.03±11.78%). All patients presented detectable IgG, which positively correlated with mild neutralizing activity (ID50=157.2, P=0.05). SARS-CoV-2 was not isolated, and a cytopathic effect was lacking. Only three synonymous variants were identified in spike protein coding regions. In conclusion, decreased IFN-γ production by NK cells and low neutralizing antibodies might favor SARS-CoV-2 long-term existence. Further, low viral load and weak viral pathogenicity was observed in COVID-19 patients with long-term SARS-CoV-2 infection.

The existences of the N→C dative bonds in the complexes between N-containing molecules and fullerenes have been verified both theoretically and experimentally. However, finding stable N→C dative bonds is still a highly challenging task. In this work, we investigated computationally the N→C dative bonds in the complexes formed by fullerene C60 with 1,2,5-chalcogenadiazoles, 2,1,3-benzochalcogenadiazoles and 1,2,4,5-chalcogenatriazoles, respectively. It was found that the N→C dative bonds are formed along with the formation of the N–Ch···C (Ch = S, Se, Te) chalcogen bonds. In the gas phase, from S-containing complexes through Se-containing complexes to Te-containing complexes, the intrinsic interaction energies become more and more negative, which indicates that the N–Ch···C chalcogen bonds can facilitate the formation of the N→C dative bonds. The intrinsic interaction energies are compensated by the large deformation energy of fullerene C60. The total interaction energies of Te-containing complexes are negative, while both of the total interaction energies of S-containing complexes and Se-containing complexes are positive. This means that the N→C dative bonds in the Te-containing complexes are more easily observed in experiments in comparison with those in the S-containing complexes and Se-containing complexes. This study provides a new theoretical perspective on the experimental observation of the N→C dative bonds in the complexes involving fullerenes. Further, the formation of stable N→C dative bonds in the complexes involving fullerenes can significantly change the properties of fullerenes, which will greatly simulate and expand the application range of fullerenes.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

Few clinical factors can help predict spontaneous culture conversion (SCC) in patients with Mycobacterium avium complex-pulmonary disease (MAC-PD). We retrospectively classified 373 MPD patients who had undergone watchful waiting without antibiotics according to the so-called ‘body mass index (BMI), age, cavity, erythrocyte sedimentation rate (ESR), and sex (BACES)’ severity. We evaluated whether lower severity is associated with a higher rate of SCC. Of 373 patients, 153 (41%) achieved SCC without antibiotics during a median follow-up of 48.1 months. There was a trend toward a higher SCC rate in patients with lower BACES severity: 48% (87/183), 37% (58/157), and 24% (8/33) in the mild, moderate, and severe BACES groups, respectively. In addition, a favorable outcome, defined as maintaining SCC or having two consecutive negative sputum cultures until the last follow-up date, was also more common in patients with lower BACES severity with 53% (97/183), 34% (54/157), and 18% (6/33) in the mild, moderate, and severe BACES groups, respectively. In multivariate analysis, moderate (hazard ratio [HR]=0.63; 95% confidence interval [CI] 0.44 – 0.91; p = 0.013) and severe BACES (HR 0.37; 95% CI 0.16 – 0.90; p = 0.028) had a significantly negative impact on favorable outcomes compared to mild BACES. Lower BACES severity may be associated with SCC in MAC-PD patients.

Hybrid fiber reinforced composites can be controlled by price, weight and various mechanical properties depending on fiber ratio and lamination method. Despite these excellent hybrid properties, there is a disadvantage that inter-laminar fracture due to external impact, which is the biggest weakness of fiber reinforced composite materials, is weak. The test specimens were prepared by using a vacuum bag method, which is manufactured by using an autoclave device. The pre-preg is manufactured in the form of a B-stage. In the process of fabricating the nanoparticle pre-preg, the homogeneizer using an ultrasonic wave was used to disperse the epoxy subject without the curing agent into nanoparticles. The dispersion of the nanoparticles was dispersed by the weight of the epoxy resin. This is to take into account the cohesion of HNT and to understand the range of cohesion of HNT in a matrix with viscosity and its phenomenon. According to the Comparison of the interlayer interfacial properties and mechanical properties of Aramid / Basalt fiber hybrid composites by HNT addition, the fracture toughness, ILSS and bending strength of specimens with HNT content of more than a certain level were decreased because of the aggregation of HNT.

Celtis sinensis is an adaptable species that is widely grown in southern China. In June 2022, a leaf blotch disease of C. sinensis was observed in Nanjing, Jiangsu, China. Based on morphological characterization, three isolates were identified as Alternaria species. Phylogenetic analysis of combined ITS, GAPDH, TEF1-α, RPB2 and Alt a 1 sequences identified the three isolates we obtained as Alternaria alternata and Alternaria koreana. Koch’s postulates were fulfilled in the greenhouse, and the pathogenicity of A. alternata and A. koreana was determined by leaf inoculation tests on C. sinensis seedlings. The symptoms of indoor inoculation were consistent with those in the field. A. alternata and A. koreana can grow at 15-35 °C, with an optimal growth temperature of 25 °C. The results of fungicide sensitivity experiments indicated that A. alternata and A. koreana were the most sensitive to prochloraz, which may be a useful strategy for the future prevention and control management of A. alternata and A. koreana. This study provides the first step for further research on A. alternata and A. koreana as pathogens of C. sinensis and provides a theoretical basis for future control strategies.

Cisplatin-based chemotherapy has long been viewed as the first-line chemotherapy for advanced and metastatic urothelial carcinoma (UC). However, many patients with UC have been classified as “cisplatin-ineligible patient”, which requires alternative chemotherapy due to their poor responses. In fact, vast majority of those who initially responded to cisplatin-based chemotherapy eventually progressed. Understanding of UC tumor immunology provided an immunopathogenic bases for immune checkpoint inhibitors, targeting PD-1 and CTLA-4, to treat cisplatin ineligible metastatic UC and patients with platinum-refractory metastatic UC. In 2020, data from the trail further showed that PD-L1 inhibitors benefit prolonged survival and progression-free survival as maintenance therapy. Besides immune-targeting therapies, manipulation of tumor microenvironment via metabolic pathways alternation, such as inhibiting tumor glycolysis, lactate accumulation and exogenous glutamine uptake, has been investigated in the past few years. In this comprehensive review, we started by introducing traditional chemotherapy of UC, and summarized current evidences supporting the use of immune checkpoint inhibitors and highlighted ongoing clinical trials. Lastly, we reviewed the tumor metabolic characteristic and the anti-tumor treatments targeting metabolic pathways.

This study investigated the relationship of acrosome reactions and fatty acid composition on fertility in boar sperm. The acrosome reaction of sperm was induced via methyl-beta-cyclodextrin (MBCD), and acrosome reaction, plasma membrane integrity, and fertility were analyzed. The fatty acid composition of the excess acrosome reacted sperm was determined via gas chromatography. The results showed that the acrosome reaction in sperm was induced over 85% of the time by 60 mM MBCD treatment, and the plasma membrane integrity was significantly decreased and was dependent on the MBCD level. The acrosome reacted sperm resulted in significantly higher saturated fatty acids (SFAs) and lower unsaturated fatty acids (PUFAs) than the non-acrosome reaction group. Moreover, the acrosome reacted sperm from 60 mM MBCD significantly decreased in vitro fertility and blastocyst formation relative to non-acrosome reacted sperm, and the acrosome reaction was positively correlated with SFAs and negatively correlated with PUFAs. Of these fatty acids, C22:5n-6 (docosapentaenoic acid [DPA]) and C22:6n-3 (docosahexaenoic acid [DHA]) were directly negatively correlated with the acrosome reaction (r = -0.982 and -0.947, respectively). In conclusion, the excessive acrosome reactions may occur by reducing the PUFAs, which may then dramatically decrease sperm fertility in pigs.

The aim of this experiment was to investigate the effects of moisture content, additives and their interactions on the fermentation quality, aerobic stability and in vitro digestibility of mixed silage of amaranth and corn meal. Amaranths and corn meal were mixed in mass ratios of 69:31, 76:24 and 84:16, and the silage water content was adjusted to 60% (W1), 65% (W2) and 70% (W3), respectively. Silage treatments included no additives (U), the addition of Lactobacillus plantarum (L), the addition of cellulase (E), and the addition of Lactobacillus plantarum + cellulase (M) mixed reagents. The results showed that pH and ammonia nitrogen (NH3-N/TN) levels were significantly lower (p < 0.05) in W1 compared to W2 and W3. At the same time, dry matter (DM), organic matter (OM), in vitro dry matter digestibility (ivDMD), in vitro dry matter digestibility (ivDMD), in vitro organic matter digestibility (ivOMD), and in vitro crude protein digestibility (ivCPD) were significantly increased (p < 0.05). Meanwhile, the aerobic stability of mixed silage of seed amaranth and corn meal decreased with increasing water content. The aerobic stability of the L, E, and M treatment groups was improved by 15, 105, and 111 hours, respectively, compared to the control group at W1. pH and NH3-N/TN levels were lower in the addition of E (E and M) than in the absence of E (U and L) (3.73, 20.1 g kg−1DM vs. 3.64, 22.9 g kg−1 DM, p < 0.05).NDF and ADF were significantly lower with the addition of E than without the addition of E (598 g kg−1 DM, 145 g kg−1 DM vs. 632 g kg−1 DM, 160 g kg−1 DM, p < 0.05). However, CP, ivDMD, ivOMD, and ivCPD were significantly higher (p < 0.05). AA and NH3-N/TN were significantly reduced (p < 0.05) with the addition of L (L and M) compared to without the addition of (U and E). In conclusion, the best fermentation quality, in vitro digestibility and aerobic stability of amaranth and cornmeal mixed silage treated with Lactobacillus plantarum + cellulase (M) were achieved at 60% water content.

Currently, the majority of industrial metal processing involves the use of taps for cutting. However, existing tap machines require relocation to specialized inspection stations and only assess the con-dition of the cutting edges for defects. They do not evaluate the quality of the cutting angles and the amount of removed material. Machine vision, a key component of smart manufacturing, is com-monly used for visual inspection. Taps are employed for processing various materials. Traditional tap replacement relies on the technician's accumulated empirical experience to determine the ser-vice life of the tap. Typically, inspecting tooth wear involves removing the tap and evaluating the degree of wear to determine if regrinding or replacement is necessary. Therefore, we propose the use of visual inspection of the tap's external features to determine whether replacement or regrinding is needed. We examined the bearing surface of the tap and utilized single images to identify the cutting angle, clearance angle, and cone angles. By inspecting the side of the tap, we calculated the wear of each cusp. We further investigated whether the cutting portion affected the length of the tool by measuring changes in tooth surface area and the amount of removed thread. This inspection process can facilitate the development of a tap life system, allowing for the estimation of the durability and wear of taps and nuts made of different materials. Statistical analysis can be employed to predict the lifespan of taps in production lines.

Existing methods for 3D human pose estimation mainly divide the task into two stages. The first stage identifies the 2D coordinates of the human joints in the input image, namely the 2D human joint coordinates. The second stage uses the results from the first stage as input to recover the depth information of human joints from the 2D human joint coordinates to achieve 3D human pose estimation. However, the recognition accuracy of the two-stage method relies heavily on the results of the first stage and includes too many redundant processing steps, which reduces the inference efficiency of the network. To address these issues, we propose the EDD, a fully End-to-end 3D human pose estimation method based on transformer architecture with Dual Decoders. By learning multiple human poses, the model can directly infer all 3D human poses in the image using a pose decoder, and then further optimize the recognition result using a joint decoder based on the kinematic relations between joints. With the attention mechanism, this method can adaptively focus on the most relevant features to the target joint, effectively overcoming the feature misalignment problem in the human pose estimation task and greatly improving the model performance. Any complex post-processing step, such as non-maximum suppression, is eliminated, further improving the efficiency of the model. The results show that the method achieves an accuracy of 87.4% on the MuPoTS-3D dataset, significantly improving the accuracy of end-to-end 3D human pose estimation methods.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

Protection suit is vital for fireman’ safety. Traditional protection suit just physically protects fireman from empyrosis, but can not locate the body injury position from the impact debris. Herein, we present a wearable impact debris positioning system for fireman protection suit alarming based on accelerometer array. The wearable piezoelectric accelerometers with distribute regularly on the suit to detect the vibration on different body parts, which is conducive to positioning injured body parts. In addition, the injured parts can be displayed on the dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11ms attributing to smart signal processing method. This work provides a reliable and smart method for locating and assessing the body injury position from the impact debris, which is significant for fire disaster commander to rescue injured fireman in time.

Acute lymphoblastic leukemia is the most common malignancy in children and is characterized by numerous genetic and epigenetic abnormalities. Epigenetic mechanisms, which involve DNA methylations and histone modifications, result in the heritable silencing of genes without a change in their coding sequence. Emerging studies are increasing our understanding of the epigenetic role of leukemogenesis and have demonstrated the potential of DNA methylations and histone modifications as a biomarker for lineage and subtypes classification, predicting relapse, and disease progression in ALL. Epigenetic abnormalities are relatively reversible when treated with some small molecule-based agents compared to genetic alterations. In this review, we conclude the genetic and epigenetic characteristics in ALL and discuss the future role of DNA methylation and histone modifications in predicting relapse, finally focus on the individual and precision therapy targeting epigenetic alterations.

Background: This study explored the effects of a virtual reality exercise program on overweight middle-aged women. Methods: This randomized controlled trial included women 4065 years of age with a body mass index (BMI) of 23 kg/m2 or more living in D city. The virtual reality environment was set up by attaching an IoT sensor to an indoor bicycle and linking it with a smartphone, enabling exercise in an immersive virtual reality through a head-mounted display. Results: In the virtual reality exercise group, the BMI was significantly decreased after the 8-week intervention compared with the baseline value (F=100.806, p<.001). The depression scores were significantly different among the three groups, with the intervention effect being more significant in the virtual reality exercise group than in the indoor bicycle exercise and con-trol groups (F=3.462, p<.001). Furthermore, the levels of exercise fun (F=12.373, p<.001) and exer-cise immersion (F=14.629, p<.001) were significantly higher in the virtual reality exercise group than in the indoor bicycle exercise and control groups. Conclusions: The virtual reality exercise program positively affected the BMI and the levels of depression, exercise fun, and exercise im-mersion in overweight middle-aged women. It is an effective home exercise program for obesity management in this population.

Background: Disulfidptosis, a recently identified form of cell death triggered by excessive cysteine accumulation and subsequent disulfide stress, has emerged as a novel mechanism of cell death. Despite its significance, the role of disulfidptosis in the tumor microenvironment (TME) remains poorly understood. Methods: In this study, we employed single-cell RNA sequencing data from 100,987 cells of 11 osteosarcoma (OS) patients. Using the non-negative matrix factorization (NMF) algorithm, we performed dimensionality reduction analysis to identify distinct subtypes characterized by 14 disulfidptosis-related genes across major cell types within the TME. Subsequently, we assessed the prognosis and immunotherapy response associated with each disulfidptosis-related subtype, leveraging publicly available databases comprising osteosarcoma data and immunotherapy cohorts. Results: We identified distinct subtypes within tumor-associated fibroblasts, tumor-infiltrating lymphocytes, and macrophages, which we named and annotated based on their characteristic genes. Furthermore, we observed a close association between disulfidptosis-related genes and key biological features of immune cells within the TME, elucidating inferred pseudotime trajectories. Notably, integrating bulk-seq data of osteosarcoma patients, we observed significant differences in overall survival rates among the disulfidptosis-related subtypes. Particularly, the disulfidptosis-related subtype within tumor-associated fibroblasts exhibited superior discriminatory ability in predicting the response of patients undergoing immunotherapy, surpassing other cell subtypes. Our cell-cell communication analysis highlighted extensive and specific interactions between disulfidptosis-related subtypes and osteosarcoma cells. Furthermore, we confirmed the histological localization of the CAPZB+CAF subtype within osteosarcoma tissue and osteoclastoma using immunofluorescence (IF) techniques. Conclusions: Collectively, our study sheds light on the intercellular communication facilitated by disulfidptosis in the TME, underscoring its involvement in the biological functions and immunotherapy response of osteosarcoma.

Coronavirus disease 2019 (COVID-19) is a global pandemic caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). To contain the virus, numerous preventive measures have been taken including isolation of patients, careful infection control, social distancing, and taking vaccine. So far, new confirmed and death cases are still increasing. SARS-CoV-2 invades cells by using the angiotensin converting enzyme 2 (ACE2). ACE2 is an essential enzyme of the renin-angiotensin system (RAS) which converts angiotensin II (Ang II) to angiotensin (1-7). ACE2 is expressed in different organs, including lung, heart, and kidney. A high number of COVID-19 patients developed kidney injury has been reported. Renal impairment and acute injury are associated with mortality of COVID-19, which is 14-16 times higher than other general patients. Acute Kidney Injury has been occured in 2.9 up to 43% of intensive care unit patients. The increasing evidence show that the components of RAS can activate the complement cascade, and cytokines production. Kidney injury caused by SARS-CoV-2 is related mainly to systemic and local inflammation. Moreover, the uncontrolled immune responses mediated by SARS-CoV-2 including hypercytokinaemia, secondary hemophagocytic lymphohistiocytosis, antibody dependent enhancement, complement system, and phagocytic cells activation can contribute in the virus pathogenesis leading to associated renal dysfunction. However, the role and crosstalk between of RAS components and immune response in mediating kidney injury remain undefined. In this review, we focus on the recent studies to provide the pathogenesis of SARS-CoV-2 interacting with RAS and immune responses to mediate kidney injury.

Using the 2011-2020 digital inclusive finance data released by Peking University and the index system constructed by the Blue Book of China Rural Revitalization and Development Index (2018), this paper analyzes the dynamic evolution of the digital inclusive finance and the rural revitaliza-tion from time and space dimensions with the help of kernel density estimation, Markov chain and Moran index. Using The Gini coefficient decomposition method to analyze the source of differ-ences in digital inclusive finance, and then using the spatial autoregressive (SAR) model and ge-ographically weighted regression (GWR) model to study the boosting effect of digital inclusive finance on rural revitalization from the perspective of spatial aggregation and spatial differentia-tion, respectively. The results show that: (1) The growth rate of China's digital inclusive finance slows down year by year, and the inter-provincial differences increase year by year and show gradient characteristics, indicating that there may be a trend of multipolar differentiation. The overall level of Rural Revitalization shows an increasing trend, and the gap between provinces is still apparent. (2) The evolution of digital inclusive finance and rural revitalization is a slow ad-justment process, and there has been no cross-level jump in the past ten years. In digital inclusive finance, the liquidity from the highest and lowest levels to the medium level is high. However, the liquidity in the states of rural revitalization development level is not high. (3) Rural revitalization has a positive spatial spillover effect. The level of rural revitalization in the western area is signif-icantly lower than in the eastern area. At the same time, there is no significant difference between the east and central areas. The depth of the use of digital inclusive finance has a significant positive impact on the revitalization and development of rural areas, indicating that the further promotion of digital inclusive finance business in rural areas can substantially boost the revitalization of rural areas. (4) The boosting effect of digital inclusive finance on rural revitalization shows prominent spatial differentiation characteristics. The depth of use and the degree of digitization generally show a positive impact. The central and eastern coastal cities have the highest impact, decreasing toward the southwest and northeast. The areas with the lowest usage depth impact are clustered in the northeast, and the areas with the lowest digitization impact are clustered in the southwest.

We developed an ovarian cancer-targeted drug delivery system based on a follicle-stimulating hormone receptor (FSHR) peptide. The lipophilic chemotherapeutic drug SN38 and the photosensitizer IR820 were loaded into the phospholipid bilayer of liposomes. Near-infrared laser irradiation stimulated the generation of reactive oxygen species, causing short-term reactive molecular species and spatial-temporal restricted photodamage to the biological targets. The reactive molecular species and spatial-temporal restricted photodamage enhanced the release and uptake of chemotherapy drugs and increased the sensitivity to chemotherapy drugs in ovarian cancer cells. FSH liposomes loaded with SN38 and IR820 (SN38/IR820-Lipo@FSH) were prepared using thin-film hydration-sonication. FSH peptide binding was analyzed using 1H NMR spectrum and Maldi-Tof. The average size and zeta potential of SN38/IR820-Lipo@FSH were 105.1 ± 1.15 nm (PDI: 0.204 ± 0.03) and −27.8 ± 0.42 mV, respectively. SN38/IR820-Lipo@FSH exhibited good drug-loading properties and the in vitro release was slow. FSH significantly increased the uptake of liposomes, inhibited cell proliferation, and induced apoptosis in A2780 cells. Moreover, SN38/IR820-Lipo@FSH exhibited good tumor-targeting ability and anti-ovarian cancer activity in vivo. The SN38/IR820-Lipo@FSH exhibited specific targeting to A2780 ovarian cancer cells. The combination of chemotherapy and photodynamic treatment based on an FSH peptide-targeted delivery system may be an effective approach to treating ovarian cancer.

Null-flux Electro-dynamic suspension (EDS) system promises to be one of the feasible high-speed maglev systems above 600 km/h. On account of its greater current-carrying capacity, superconducting magnet can provide super-magnetomotive force that is required for null-flux EDS system and cannot be provided by electromagnets and permanent magnets. There is already a relatively mature high-speed maglev technology with low temperature superconducting (LTS) magnets as the core, which works in the liquid helium temperature region (T≤4.2 K). 2-Generation high temperature superconducting (HTS) magnet winded by REBa2Cu3O7−δ (REBCO, RE=rare earth) tapes works above 20 K region and do not need to count on liquid helium which is rare on earth. This paper designed HTS no-insulation closed-loop coils applied for EDS system and energized with persistent current switch. The coils can work at persistent current model and has premier thermal quench self-protection. Besides, a full size double-pancake module was designed and manufactured in this paper, and it was tested in liquid nitrogen. The double-pancake module’s critical current is about 54 A and it is capable of working at persistent current model, whose average decay rate measured in 12 hours is 0.58%/day.

Despite existing strong evidence on oxidative markers overproduction following ischemia/reperfusion (I/R), the mechanism by which oxidative enzyme Cytochrome P450-2E1 (CYP2E1) contributes to I/R outcomes is not clear. In this study, we sought to evaluate the functional significance of CYP2E1 in I/R. CYP2E1 KO mice and controls were subjected to middle cerebral artery occlusion (MCAo-90min) followed by 24hr of reperfusion to induce focal I/R injury models. Then, histological and chemical analyses were conducted to investigate the role of CYP2E1 in lesion volume, oxidative stress, and inflammation exacerbation. Also, the role of CYP2E1 on the BBB integrity was investigated by measuring 20-Hydroxyecosatetraenoic acid (20-HETE) activity, as well as, in vivo BBB transfer rate. Following I/R, the CYP2E1 KO mice exhibited a significantly lower lesion volume, and neurological deficits compared to controls (p<0.005). Also, ROS production, apoptosis, and the neurodegeneration were significantly lower in the CYP2E1(-/-) I/R group (p<0.001). The BBB damage was significantly lower in CYP2E1(-/-) mice compared to WT (p<0.001), while 20-HETE production was increased by 41%. Besides, inflammatory cytokines expression and the number of activated microglia were significantly lower in CYP2E1(-/-) mice following I/R. CYP2E1 suppression ameliorates I/R injury and protects BBB integrity by reducing both oxidative stress and inflammation.

Natural products are an important source of antibacterial agents. Canthin-6-one alkaloids have displayed potential antibacterial activity based on our previous work. In order to improve the activity, twenty-two new 3-N-benzylated 10-methoxy canthin-6-ones were designed and synthesized through quaternization reaction. The in vitro antibacterial activity against three bacteria was evaluated by double dilution method. Four compounds (6f, 6i, 6p and 6t) displayed 2-fold superiority (minimum inhibitory concentration (MIC) = 3.91 µg/mL) against agricultural pathogenic bacteria R. solanacearum and P. syringae than agrochemical propineb. Moreover, the structure–activity relationships (SARs) were also carefully summarized in order to guide the development of antibacterial canthin-6-one agents.

Many studies have focused on the impacts of rainfall duration and intensity while overlooking the role of rainfall patterns on intensive tillage erosion in hilly agricultural landscapes. The objective of this study was to determine the combined effects of rainfall patterns and intensive tillage erosion on surface runoff and soil loss on sloping farmland in the purple-soil area of China. Five simulated rainfall patterns (constant, rising, falling, rising-falling, and falling-rising) with the same total precipitation were designed, and the intensive tillage erosion treatment (IT) and no-tillage treatment (NT) were subjected to simulated rainfall using rectangular steel tanks (2 m × 5 m) with a slope of 15°. To analyse the differences in the hydrodynamic characteristics induced by tillage erosion, we calculated the flow velocity (V), Reynolds number (Re), Froude number (Fr), and Darcy-Weisbach resistance coefficient (f). The results indicate that significant differences in surface runoff and soil loss were found among different rainfall patterns and stages (P < 0.05). The falling pattern and falling-rising pattern had faster runoff-initiating times and larger sediment yields than those of the other rainfall patterns. f varied from 0.30 to 9.05 for the IT and 0.48 to 11.57 for the NT and exhibited an approximately inverse trend to V and Fr over the course of the rainfall events. Compared with the NT, the mean sediment yield rates from the IT increased the dynamic range of 8.34%–16.21% among different rainfall patterns. The net contributions of the IT ranged from 2.77% to 46.39% on surface runoff and 10.14%–78.95% on soil loss on sloping farmland. Surface runoff and soil loss were positively correlated with rainfall intensity, V, and Fr but negatively correlated with f irrespective of tillage intensive (P < 0.05). For varying-intensity rainfall patterns, soil and water loss fluctuated during rainfall events, suggesting that the changes in rainfall intensity and tillage intensity would result in drastic variations in soil hydrological characteristics and sediment transport mechanisms. The time sequences of rainfall intensity in each rainfall pattern significantly affected surface runoff, soil erosion, and their contribution rates to total soil and water loss. Moreover, tillage erosion effects on soil and water loss were closely related to rainfall patterns in hilly agricultural landscapes. Our study not only sheds light on the mechanism of tillage erosion and rainfall erosion but also provides useful insights for developing tillage-water erosion prediction models to evaluate soil and water loss on cultivated hillslopes.

Influenced by the quasi-stationary Mei-yu front and the development of mesoscale low vortices on the Mei-yu front, a torrential rain event occurred in Suzhou on July 6, 2020. The 24-hour rainfall recorded by the automatic station exceeded 200 millimeters, with the highest hourly intensity surpassing 70 millimeters, accompanied by thunderstorms and strong winds. This heavy precipitation process was characterized by suddenness, extremity, long duration, high precipitation efficiency, and backward propagation. Using various data sources such as the European ERA5 reanalysis data, ground-based automatic stations, sounding, Doppler weather radar, and wind profile radar, this paper analyzed in detail the circulation characteristics and radar echo structures of this torrential rain event, and further studied the triggering, feature evolution, and maintenance mechanisms of the heavy precipitation.The results show: (1) The continuously strengthening low-level jet stream propagates downward forming an ultra-low-level jet stream. Heavy precipitation is located on the left front side of the jet exit area, where strong convergence and lifting in the boundary layer overlap with the ascending branch of the secondary circulation above the shear line, resulting in heavy precipitation. (2) A supercell storm with intense precipitation produced this heavy rainfall event, characterized by a low centroid of strong echo; echo-free vault, bounded weak echo region, and other supercell structural features. During this event, the high reflectivity factor areas corresponded to high KDP value areas, indicating a large amount of liquid water content. Vertically, the KDP column can track the rainwater mixing ratio well, and its location corresponds to the vicinity of the short-term heavy precipitation occurrence. The high KDP value area mainly consists of numerous precipitation particles, and the vertical vortex wind field structure causes rapid growth of precipitation particles through continuous rolling. Furthermore, it can be found through correlation coefficients (CC) that there are always high-value areas for CC since they correspond to areas of intense precipitation. (3) Continuous triggering of mesoscale convective cloud clusters on the east-west ground convergence line leads to new development and forms a "train effect." Strong frontogenesis in both horizontal and vertical directions triggers and sustains this heavy precipitation event. The significant increase in liquid water and water vapor density has indicative significance for the occurrence of heavy precipitation.

Since the development of CBCT had been utilized in dentistry, the images of the CBCT can assist the surgeon to evaluate the anatomy carefully. Despite the value of the radiology evaluation, the implant procedures may require additional consideration rather than only evaluating the anatomical factors. The purpose of this study is to evaluate the predictability of using CBCT alone to plan for implant placement on the edentulous patient digitally CBCT images were analyzed by clinicians, measuring the ridge heights and widths of 4 selected implant sites in the maxillary and 2 selected implant sites in the mandibular arches for 91 patients planning for the implant-supported overdenture. (A total of 47 patients out of the 91 had completed the implant placement on the edentulous ridge, contributing to 55 upper and/or lower arches (136 dental implants). . Both predictabilities are low, implying the CBCT planning for implant placement on the edentulous ridge is not a good index and is insufficient to predict the surgical procedures as a solo method. The finding of this study indicates that digital planning by CBCT is insufficient to serve as an individual tool to predict implant procedures. Further information and evaluation must be considered for implant placement on the edentulous ridge.

With the continuous development of Artificial Intelligence technology and Internet of Things engineering, more and more driver-less vehicles have been developed and put into the industrial production. The birth of driver-less vehicles undoubtedly brings new vitality to a large amount of industries, particularly in transportation. For the mining industry, transportation is undoubtedly an extremely important link in the whole production process. If the driver-less vehicles can be applied to the underground mines, it can not only improve the production and transportation capacity of the whole mine, but also can reduce the occurrence of many mine safety accidents. ZigBee WSN technology can play a greater role in the narrow environment like underground mines according to the relevant literature, this concept paper just like a engineering project plan mainly tries to integrate the ZigBee WSN technology and the communication-based train control (CBTC) system to explore the possibility of the driver-less vehicles to be used in the underground mines, which aims to solve practical engineering problems for the engineering projects. As the mining engineers, we put forward the concept of this integrated system in this concept paper, but we need to continue to work hard for the future of the underground mines. This concept paper serves just as a guide to the Tossing out a brick to get a jade gem, has a few implications for the development of underground mine transportation.

Based on the two-flavors Polyakov quark-meson model, we study the bubble dynamics of a first-order phase transition in chiral phase diagram at high density but low temperature in the framework of the homogeneous thermal nucleation theory. Under the mean-field approximation, after obtaining the effective potential with inclusion of the fermionic vacuum term, we build a geometric approach to probe two possibly existing minima, which can actually tunnel through a bounce interpolated between a metastable vacuum to an adjacent true vacuum. By separating our discussions into a weak first-order hadron quark phase transition and strong ones, the bubble profiles, the surface tension, the typical radius of the bounce and the saddle point action in the presence of a nucleation bubble as a function of temperature are numerically calculated in detail as the chemical potentials are fixed at $\mu=306 \mathrm{MeV}$ and $\mu=310 \mathrm{MeV}$. our results show that the surface tension remains a small value even when the density is very high and phase boundaries for hadron and quark matter should be resized properly according to the saddle point action evaluated on the bounce. It is also noticed that the inclusion of the deconfinement phase transition in term of the Polyakov loop does not change chiral phase transition dramatically for light quarks.

This paper presents the experimental implementations of the mathematical models and algorithms developed in Part I. Two experiments are carried out. The first experiment aims at the determinations of the correction coefficients of the mathematical model. The dot grid target is measured and the measurement data are processed by our developed and validated algorithms introduced in Part I. The values of the coefficients are indicated and analysed. Uncertainties are evaluated with implementation of the Monte Carlo method. The second experiment measures a different area of the dot grid target. The measurement results are corrected according to the coefficients determined in the first experiment. The mean residual between the measured points and their corresponding certified values reduced 29.6% after the correction. The sum of squared errors reduced 47.7%. The methods and the algorithms for raw data processing, such as data partition, fittings of dots’ centres, K-means clustering, etc., are the same for both two experiments. The experimental results demonstrate that our method for the correction of the errors produced by the movement of lateral stage of confocal microscope is meaningful and practicable.

In order to make full use of the complementarity of existing navigation systems to improve the navigation and positioning accuracy, this paper investigates the visual/INS integrated navigation system based on the factor graph optimization (FGO) algorithm. In the traditional visual/INS integrated navigation system, there is often the problem of image blurring due to the rapid change of light and shadow captured by the vision sensor and the attitude change of the carrier, which leads to the decrease of the positioning accuracy of the combined navigation system. Therefore, this paper firstly introduces Retinex algorithm and BID algorithm to carry out the design of image de-blurring method; then implements the visual/INS integrated navigation algorithm based on the factor graph optimization method; finally, the experimental scheme is designed, comparative experiments are carried out, and the researched method is verified by using the public dataset. The experimental results show that the combined navigation algorithm realized in this paper has high accuracy, and its positioning accuracy is improved by 40% compared with visual positioning.

As China put forward its “carbon emissions peak and carbon neutrality” goals, how to achieve carbon reduction had become a key for China’s goal. The manufacturing industry is an important source of carbon dioxide emissions. For a manufacturing country like China, adjustments in various aspects of the industry would have a huge impact on carbon emissions. As an important reform of contemporary production mode, the process of production automation in China will inevitably affect China's carbon emissions. Therefore, the analysis of the impact of production automation on carbon dioxide emissions was an important basis for judging the future carbon reduction in China. Refer to the traditional study of carbon Kuznets curve, this paper analyzed the impact of average wage on production automation and the role of production automation in the carbon Kuznets curve(CKC). This paper proposed that production automation plays a mediating role in the process of carbon emissions, and gives a verification model of the mediating role. By analyzing the relationship between average wage and production automation process, the U-shaped curve relationship between them was verified. By examining the relationship between carbon dioxide emission data and production automation industry in China, we verified that production automation plays a partial mediating role in the change of carbon Kuznets curve. Combined with the analysis of the two parts, this paper believed that with the continuous development of China's intelligent manufacturing industry, China's carbon reduction prospects were more optimistic, and there was a good industrial foundation to achieve the “carbon peaking and carbon neutrality” goals. Finally, this paper proposes policy suggestions as increase research investment in production automation, help promote the application of production automation, encourage the research and application development of low-carbon technology, especially encourage modular design, so as to give full play to the role of production automation in the process of carbon neutrality in China.

One of the most leading causes of death worldwide is Colorectal cancer(CRC). Polyp segmentation is the most important detected measure for preventing CRC. However, there is still a missing rate for diminutive polyps and multiple ones. In order to solve the phenomenon, we propose to introduce auxiliary attention module(AAM) that can enhance the learning of features related to multiple and diminutive polyps by focusing more on the located and detailed information. Meanwhile, we design to decrease missed rate of multiple and diminutive polyps by implementing an area adaptive loss(AAL) which adapts the weight according to the area and the number of polyps. Our proposed novel AAM and AAL concentrates on training with hard examples and localized information. To evaluate the effectiveness and generalization ability of our proposed model, We utilize three different datasets of variable sizes and a cross dataset. Our proposed method achieves the best results on the Kvasir-SEG dataset, the CVC-ClinicDB dataset and the cross dataset, particularly for the Kvasir-Sessile dataset consisting of small,flat and diminutive polyps. Extensive experimental results show that our proposed DoubleAANet surpass the performance of all existing state-of-the-art segmentation methods.

The power conversion efficiency (PCE) of polymer solar cells (PSCs) are strongly depended on the bulk-heterojunction active layer. Here, the 1,8-diiodooctane (DIO) additives have been added into the PCDTBT: PC70BM blend PSCs. Based on the higher boiling point than host solvent ODB and better solubility of PC71BM, the device photovoltaic properties with DIO additive were changed obviously. The investigations of EQE indicate that the DIO can influence the charge recombination and transportation process, and absorption studies demonstrate that the charge carriers generation process can also be affected by DIO. The overall impact reflected on the decreased equivalent resistant. With 3% v/v DIO, the Jsc, Voc and FF are both increased. Correspondingly, a highest PCE is achieved of 6.15%, while the reference device without DIO only has a PCE of 5.23%. Hence, adding DIO solvent additive is a effective method for the photovoltaic properties improving of PCDTBT: PC70BM blend PSCs.

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

Abstract: This study was aimed to determine the influence of the volume fraction of steel fibers and on fracture parameters of concrete. Fifty notched steel fiber reinforced concrete (SFRC) beams and ordinary concrete beams with dimensions of 100mm×100mm×515mm were cast and tested via three-point bending test. Among them, the type of steel fiber is milling type (MF), and the volume fraction of steel fiber added is 0%, 0.5%, 0.5%, 1.5%, 1.5%, 2%, respectively. The effects of the steel fiber volume fraction (VF) on the critical stress intensity factor (KIC), fracture energy (GF), the deflection at failure(δ0), the critical crack mouth opening displacement (CMODC) and the critical crack tip opening displacement (CTODC)were studied. Through the analysis of test phenomena and test data such as load-deflection (P-δ) curve, load-crack mouth opening displacement (P-CMOD) curve and load-crack tip opening displacement (P-CTOD) curve following conclusions are drawn: With the increase of steel fiber volume fraction, some fracture parameters increase gradually and maintain a certain linear growth. The gain ratio of fracture parameters increases significantly, and the gain effect is obvious. Through this law of growth, the experimental statistical formulas of fracture energy and critical stress intensity factor are summarized.

The use of cemented aeolian sand-fly ash backfill (CAFB) material to fill the mining area to improve the surface subsidence damage caused by underground coal mining is in the development stage. Their performance with large overflow water and strength loss is not well understood. Few research has been conducted to understand the effects of aeolian sand and coal gangue on the rheological properties of CAFB with plasticizers. Therefore, the aim of this study is to investigate the effects of a plasticizer on the rheological properties, specifically yield stress and viscosity, of CAFB prepared with aeolian sand and coal gangue. CAFB mixes containing 0%, 0.05%, and 0.1% plasticizer were prepared, and yield stress and viscosity were determined at different time intervals over the period. Additional tests, such as thermal analysis and zeta potential analysis were also conducted. It was found that the rheological properties of CAFB is the comprehensive manifestation of the composite characteristics of various models. Reasonable particle size distribution and less amount of plasticizer can ensure the stability of slurry structure, reduce the slurry settlement and the risk of pipe blocking. The findings of this study will be beneficial in the design and production of CAFB material.

Facilitating sustainable cooperation between schools and enterprises has become an important concern in many countries. However, there remains a gap in understanding the approaches taken by central and local governments to foster such cooperation through the lens of evolutionary game theory. Therefore, this paper aims to develop a quadrilateral evolutionary game model involving schools, enterprises, the central government, and local governments, to analyze the conditions under which governments can effectively promote school-enterprise cooperation. Our findings indicate that benefit is a decisive factor that affects the strategies of all parties. When the benefits of cooperation are sufficiently attractive, schools and enterprises are inclined to cooperate with each other independently of governmental intervention. While increasing incentives and penalties from the central government and local governments can stimulate school-enterprise cooperation, these measures are not sustainable in the long term. Additionally, the impact of the central government’s incentives and penalties on local governments in promoting school-enterprise cooperation is limited. Enhancing policy efficacy and the practical outcomes of school-enterprise cooperation is essential, which not only strengthens the bond between schools and enterprises but also ensures deep and enduring governmental involvement.

Promoting close and sustainable cooperation between schools, enterprises, and government has become an important concern in many countries. Based on evolutionary game theory, this paper constructs a tripartite evolutionary game model of schools, enterprises, and government in order to analyze the stability of strategies of the different players. The results show that the main factor that influences the stability of the strategies of schools and enterprises is the reward of positive cooperation from sources other than the government, and the main factor that influences the stability of the strategy of the government is the benefit of positive cooperation strategy under the scenario where schools cooperate with enterprises. Therefore, the government should focus on implementing more effective policies, such as increasing the incentives and penalties, improving the mechanism for managing conflicts, ensuring the fairness of benefits distribution, and clarifying the responsibilities of different departments; schools should focus on providing more practical curricula and programs for students, training high-quality teachers, and perfecting talent cultivation to meet the needs of enterprises; and enterprises should focus on providing job experiences for students and transforming the results of schools’ teaching and theoretical research into practical productivity.

Multi-gap Resistive Plate Chamber has been attracting increasing attention and has been studied in recent decades because of its good efficiency, high time resolution and relatively low cost. It has become a new standard technology for the Time of Flight system in particle and high energy physics experiments. In this paper, we introduce the operation principle and structure of the MRPC detector and review the applications on the Time of Flight system in several famous experiments, such as STAR, CBM and SoLID. The performances including time resolution and particle identification are discussed in detail. Some recent advances and perspectives with regard to the future development of the next generation MRPC are also outlined.

As the leader of the largest economy, President of the United States has substantive influence on addressing the global climate change problem. However, presidential election is often dominated by issues other than energy problems. This paper focuses on the on-going 2016 presidential election, examining the energy plans proposed by the leading Democrat and Republican candidates. Our data from the Iowa caucus survey in January 2016 suggests that voters are more concerned about terrorism and economic issues than environmental relative issues. We then compare the Democratic and Republican candidate’s view of American’s energy future, and evaluate their proposed renewable energy targets. We find that the view on renewable energy is polarized between Democratic and Republican candidates, while candidates from both parties agree on the need for energy efficiency. Results from our ordinal least squares regression models suggest that Democratic candidates have moderate to ambitious goals for developing solar and other renewable energy. The Republican candidates favor fossil fuel and they neglect to provide any plan for renewable energy. In addition, this trend of polarization has grown more significant when compared with the past three presidential elections. Our observation suggests that energy issues need to be discussed more to draw broader attention to salient issues of diversifying and decarbonizing the nation’s energy system.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Although sarcopenia is known to be a risk factor for non-alcoholic fatty liver disease (NAFLD), whether NAFLD is a risk factor for the development of sarcopenia is not clear. We investigated bidirectional relationships between NAFLD and low skeletal muscle mass index (LSMI) using three different datasets. Participants were classified into LSMI and normal groups. LSMI was defined as a body mass index (BMI)-adjusted appendicular skeletal muscle mass &lt;0.789 in men and &lt;0.512 in women or as the sex-specific lowest quintile of BMI-adjusted total skeletal muscle mass. NAFLD was determined according to NAFLD liver fat score or abdominal ultrasonography. The NAFLD groups showed a higher hazard ratios (HRs) with 95% confidence intervals (CIs) for LSMI than the normal groups (HRs=1.213, 95% CIs=1.050–1.402). The LSMI groups also showed a higher HRs with 95% CIs for NAFLD than normal groups (HRs=1.564, 95% CIs=1.378–1.775). Participants with NAFLD had consistently less skeletal muscle mass over 12 years of follow-up. In conclusion, LSMI and NAFLD showed a bidirectional relationship. Maintaining muscle mass should be emphasized in the management of NAFLD.

Background: During pregnancy, major physiological changes occur in every system. Understanding the hemodynamic changes in different stages of pregnancy can help to identify abnormal states during pregnancy. Harmonic analysis could be a useful tool in monitoring the state of the ventricular-arterial system during pregnancy. The aim of this study was to investigate the specific statistical relationships between changes in harmonic indices during different stages of pregnancy. Methods: A Total of 380 women (190 pregnant women and 190 age-matched non-pregnant women), with ages ranging from 20 to 45, were enrolled in the study. The visit measured the subject’s hemodynamic parameters including heart rate, systolic blood pressure (SBP), diastolic blood pressure (DBP) and photoplethysmography (PPG). SBP and DBP were evaluated by an automatic blood pressure monitor. PPG signal were continuously recorded for 12-seconds using a PPG sensor. Spectrum analysis of the PPG signal was performed to evaluate the first five harmonic components (C1 – C5) and harmonic phases (P1 – P5). Result: A comparison between pregnant women and non-pregnant women showed that the non-pregnant women had lower DBP, C3, C5 and P5 (p<0.05). Waist Circumference, Heart rate, C2, C4 and P2 were higher in pregnant women. Logistic regression analysis was used to determine the associations between pregnancy and harmonics indices. C2, C4 and P3 were positively and P1 and P4 were negatively associated with pregnancy after controlling age, BMI, waist circumference, heart rate, SBP and DBP. Conclusion: The results of this study provide information on the changes in the harmonic frequency components during various stages of pregnancy. The harmonic components of the PPG signal have independent predictive value for changes in a woman's physiology during pregnancy. Since non-invasive PPG measurements can be performed frequently and easily, in the future, it is possible that the hemodynamic changes from some pregnancy-related disorders could be studied by harmonic analysis.

The Oryzaephilus surinamensis L. (Coleoptera: Silvanidae), is widely distributed all over the world, this beetle causes serious damage to stored products. Much attention has been paid to use food attraction or food volatile as a non-pollution method to achieve pest management. However, in this study, six most attractive food to O. surinamensis were selected among thirty eight food. Furthermore, the food mixture M17 with the best attractiveness were selected among the eighteen food mixtures combined by these six foods at different ratio. Subsequently food mixture M17 were tested in actual barn and compared with commercial attractant. We collected the volatile from food mixture, the volatile compounds attractive to this beetle also. We identified six electrophysio-logically active compounds responsible for the attraction of O. surinamensis, among the six chemically identified compounds, nonanal, dodecane, tridecaneand β-caryophyllene significantly attracted O. surinamensis when tested individually in behavioral assays. Blend of six chemicals according to food volatile concentration was most attractive to the beetles. The findings of this study reveal that food mixture M17 and food volatile can be potentially used for development of effective attractants for management of O. surinamensis.

Using co-precipitation to synthesize (CeO2)0.95(Y2O3)0.05 (YDC) and solid reaction method to synthesize (CeO2)0.75(ZrO2)0.25 (ZDC), and the characterization for both crystal structure and micro-structure of the two materials was conducted with X-ray diffraction (XRD) and scanning electron microscope (SEM) methods. Prepare the YDC and ZDC based limited current O2 sensor by employing platinum pasting bonding method. Sensing characteristics of the sensor were obtained at different conditions and study on the impact of temperature, O2 concentration as well as water vapor pressure on the sensing characteristics had been conducted. XRD results show that the phase structure of both YDC and ZDC is cubic phase. SEM results show that both YDC and ZDC layers are dense layers, which are then qualified to be the composition materials of the sensor. This limited current O2 sensor shows good sensing performance and conforms to the Knudsen model. Log(IL•T) depends linearly on 1000/T with R2 of 0.9904, IL depends linearly on x(O2) with R2 of 0.9726 and sensing characteristics are not affected by p(H2O).

In this paper, the fixed-time stabilization problem for a class of uncertain chained system is addressed by using a novel nonsingular recursive terminal sliding mode control approach. A fixed-time controller and an adaptive law are designed to guarantee the uncertain chained form system both Lyapunov stable and fixed-time convergent within the settling time. The advantage of the controller based on the sliding mode is that the settling time does not depend on the system initial state. Furthermore, we use RBF neural network to estimate the uncertainty of the system. Finally, the simulation results demonstrate the performance of the control laws.

In this research, a novel collector cetyl trimethyl ammonium chloride (CTAC) was used to separate hematite from quartz via reverse flotation for the first time. Micro-flotation tests showed that CTAC had a strong ability to selectively collect quartz and a separation of hematite from quartz could be accomplished with a concentration of 0.00263 mmol/L CTAC. Zeta-potential measurements indicated that the positive CTAC+ species could selectively increase the surface potential of quartz, but it had rather a weak effect on the hematite surface. X-ray photoelectron spectroscopy (XPS) detection indicated that CTAC had a stronger binding affinity to oxygen sites on the surface of quartz than that of hematite, resulting in a large amount of CTAC predominantly adsorbed on quartz rather than hematite.

New antimicrobial approaches are essential to counter antimicrobial resistance. The drug development pipeline is exhausted with emergence of resistance resulting in unsuccessful trials. The lack of an effective drug developed from the conventional drug portfolio has mandated the introspection into the list of potentially effective unconventional alternate antimicrobial molecules. Alternate therapies, that are clinically explicable forms include monoclonal antibodies, antimicrobial peptides, aptamers and phages. Clinical diagnostics optimizes the drug delivery. In the era of diagnostic-based applications, it is logical to draw diagnostic based treatment for infectious diseases. Selection criteria of alternate therapeutics in infectious disease include detection, monitoring of response and resistance mechanism identification. Integrating these diagnostic applications is disruptive to the traditional therapeutic development. The challenges and mitigation methods need to be noted. Applying the goals of clinical pharmacokinetics that include enhancing efficacy and decreasing toxicity of drug therapy this review analyses the strong correlation of alternate antimicrobial therapeutics in infectious diseases. The relationship between drug concentration and the resulting effect defined by the pharmacodynamic parameters are also analyzed. This review analyzes the perspectives of aligning diagnostic initiatives into the use of alternate therapeutics with a particular focus on companion diagnostic applications in infectious diseases.

Crop breeding is an important global strategy to meet sustainable food demand. CRISPR-Cas is a most promising gene-editing technology for rapid and precise generation of novel germplasm, and leads to revolutionary crop breeding innovation. In this review, we summarize recent advance of CRISPR/Cas technology in gene function analyses and generation of new germplasms with increased yield, improved product quality, and enhanced resistance to biotic and abiotic stress. We highlight their applications and breakthroughs in agriculture including crop de novo domestication, decoupling the gene pleiotropy tradeoff, crop hybrid seed conventional production, hybrid rice asexual reproduction, and double haploid breeding. Moreover, the challenges and development of CRISPR/Cas technology in crops are also discussed.

Ammonia-oxidizing microorganism communities are abundant and functionally efficacious in nitrification. However, ammonia-oxidizing archaea (AOA) and ammonia-oxidizing bacteria (AOB) groups complicate this process in subtropical streams. This study investigates the abundance of ammonia-oxidizing communities south of the Dabie Mountains, China, using quantitative polymerase chain reaction (qPCR). Clone libraries were utilized to analyze the abundance and microbial structures of AOA and AOB in sediments. Such analysis may provide strong evidence reflecting the links within the environment. The results show that AOB had a lower abundance of copies of the ammonia-oxidizing gene (amoA) than AOA. Interestingly, the AOA and AOB community compositions were correlated with ecological characteristics. The dissolved oxygen (DO) and oxidation-reduction potential (ORP) had significant positive correlations, whereas the phosphorus within the structure had a negative correlation with the abundance of both groups. Our study shows that it might adopt some species related to Nitrosotalea clusters that can resist comparably higher pH (toward pH 6.5). Together, these results imply that the physiological adaptation of microbial guilds to environmental pressures in ammonia-oxidizing archaea might allow them to have a more substantial function of ammonia-oxidizing communities in natural habitats.

Compliant amplifying mechanisms are used widely in high-precision instruments driven by piezoelectric actuators, and the dynamic and static characteristics of these mechanisms are closely related to instrument performance. Although the majority of existing research has focused on analysis of their static characteristics, the dynamic characteristics of the mechanisms affect their response speeds directly. Therefore, this paper proposes a comprehensive theoretical model of compliant amplifying mechanisms based on the multi-body system transfer matrix method to analyze the dynamic and static characteristics of these mechanisms. The effects of the main amplifying mechanism parameters on the displacement amplification ratio and the resonance frequency are analyzed comprehensively using the control variable method. An iterative optimization algorithm is also used to obtain specific parameters that meet the design requirements. Finally, simulation analyses and experimental verification tests are performed. The results indicate the feasibility of using the proposed theoretical compliant amplifying mechanism model to describe the mechanism’s dynamic and static characteristics, which represents a significant contribution to the design and optimization of compliant amplifying mechanisms.

In recent decades, as eutrophication in inland and coastal waters (ICWs) has increased due to anthropogenic activities and global warming, so has the need for timely monitoring. Compared with traditional sampling and laboratory analysis methods, satellite remote sensing technology can provide macro-scale, low-cost, and near real-time water quality monitoring services. The Geostationary Ocean Color Imager (GOCI), integrated onboard the Communication Ocean and Meteorological Satellite (COMS) from the Republic of Korea, was the first geostationary ocean color observation satellite and was operational from April 1, 2011 to March 31, 2021. Over ten years, GOCI has observed oceans, coastal waters, and inland waters within its 2,500 km×2,500 km target area centered on the Korean Peninsula. The most attractive feature of GOCI, compared with other commonly used watercolor sensors, was its high temporal resolution (1h, eight times daily from 0 UTC to 7 UTC), providing the opportunity to monitor the quality of ICWs, where optical properties can change rapidly throughout the day. This systematic review aims to comprehensively review GOCI features and applications in ICWs, analyzing progress in atmospheric correction algorithms and water quality monitoring. Analyzing 123 articles from the Web of Science and China National Knowledge Infrastructure (CNKI) through a bibliometric quantitative approach, we examined GOCI’s strength and performance with different processing methods. These articles reveal that GOCI played an essential role in monitoring the ecological health of ICWs in its observation area in East Asia. GOCI has led the way to a new era of geostationary ocean satellites, providing new technical means for monitoring water quality in oceans, coastal zones, and inland lakes. We also discuss the challenges encountered by geostationary satellites in monitoring water quality and provide suggestions for improvements.

Climate change and food security are the most relevant issues to be considered in sustainable agricultural development. The FAO’s initiative of climate-smart agriculture has attracted international attention. Since then, the smart agriculture (SA) has been recognized as the most influential trends in contributing to agricultural development. Therefore, encouraging farmers to adopt digital technologies and mobile devices into farming practices becomes a policy priority worldwide. However, there is limited literature available on psychologic factors that drive farmers’ intentions to adopt SA technologies. The purpose of this study is to investigate how farmer’s knowledge and attitude toward SA affects their adoption of smart technologies in Taiwan. A total of 321 farmers participated in the project’s survey in 2017 and 2018, from which the data was used to perform an OLS regression model of SA adoption. This study contributes to a preliminary understanding of relationship between innovation and adoption of SA technologies in a small-scale farming economic context. The findings suggest that the policy makers and R&D institutes need to concentrate on improving market access for well-known and high important SA technologies.

Surface-enhanced Raman spectroscopy (SERS) is commonly used for super-selective analysis through nanostructured silver layers in the environment, food quality, biomedicine, and materials science. To fabricate a high-sensitivity but more accessible device of SERS, dc magnetron sputtering technology was used to realize high sensitivity, low cost, stable deposition rate, and rapid mass production. This study investigated various thicknesses of a silver film ranging from 3.0 to 12.1 nm by field-emission-scanning-electron microscope, X-ray diffraction, and X-ray photoelectron spectroscopy. In the rhodamine 6G (R6G) testing irradiated by a He-Ne laser beam, the analytical enhancement factor (AEF) of 9.35x108, the limit of detection (LOD) of 10-8 M, and the relative standard deviation (RSD) of 1.61% were better than other SERS substrates fabricated by the same dc sputtering process because the results show that the 6 nm thickness silver layer has the highest sensitivity, stability, and lifetime. The paraquat and acetylcholine analytes were further investigated and high sensitivity was also achievable. The proposed SERS samples were evaluated and stored in a low humidity environment for up to forty weeks, and no spectrum attenuation could be detected. Soon, the proposed technology to fabricate high sensitivity, repeatability, and robust SERS substrate will be an optimized process technology in multiple applications.

Radiotherapy is a crucial treatment for head and neck malignancies, but it usually leads to sensorineural hearing loss (SNHL). Changes in the immune microenvironment and sensorial neuroepithelium of the inner ear after radiation exposure remain poorly understood. This study investigated cochlear morphology and macrophages in the inner ear after high-dose irradiation. The heads of 8-week-old Cx3cr1GFP/+ heterozygous male mice were irradiated with 30Gy X-rays and biological samples were taken on the 1st, 7th, and 10th days after irradiation. Auditory brainstem responses were used to assess auditory function in mice. The changes of basal membrane hair cells, spiral ganglion (SGN), and inner ear macrophages were observed using hematoxylin-eosin (HE) staining and immunofluorescence staining. The expression of inflammatory mediators in the inner ear was detected by reverse transcription-polymerase chain reaction (RT-PCR) in cochlear tissue. As a result, there was no significant hair cell loss after high doses of radiation, but the mice developed full-frequency hearing loss on day 10 when HE staining revealed SGN atrophy and immunofluorescence revealed decreased neurofilament expression. The number of macrophages in the inner ear decreased over time. RT-PCR showed that cochlear inflammatory factors and chemokines were briefly up-regulated on the first day after irradiation and then decreased over time. In summary, high-dose irradiation causes acute SNHL that does not involve hair cell loss and may be associated with SGN changes. Radiation-induced SNHL is accompanied by a reduction in cochlear macrophages and changes in the immune microenvironment, but the relationship between the two has yet to be explored.

For screening excellent lactic acid bacteria (LAB) strains to inhibit Escherichia (E.) coli (ETEC) K88, inhibitory activities of more than 1100 LAB strains isolated from different materials and kept in the lab were evaluated in this study. Nine strains with inhibition zone at least 22.00 mm (including that of hole puncher 10.00 mm) and good physiological and biochemical characteristics identified by 16S DNA gene sequencing and recA gene multiple detection, were assigned to Lactobacillus (L.) plantarum subsp. plantarum (5), L. fermentum (1), L. reuteri (1), W. cibaria (1) and E. faecalis (1), respectively. As investigated for their tolerance abilities and safety, only strain ZA3 possessed high hydrophobicity and auto-aggregation abilities, had high survival rate in low pH, bile salt environment and GI fluids, sensitive to ampicillin, resistant to norfloxacin and amikacin, without hemolytic activity and didn’t carry antibiotic resistance genes, exhibited broad spectrum activity against a wide range of microorganisms, and antibacterial substance may attribute to organic acids, especially lactic acid and acetic acid. The results indicated that the selected strain L. plantarum subsp. plantarum ZA3 could be considered a potential probiotic to inhibit ETEC K88 for further research.

The Cav3.2 T-type calcium channel is implicated in various pathological conditions, including cardiac hypertrophy, epilepsy, autism, and chronic pain. Phosphorylation of Cav3.2 by multiple kinases plays a pivotal role in regulating its calcium channel function. The calcium/calmodulin-dependent serine/threonine phosphatase, calcineurin, interacts physically with Cav3.2 and modulates its activity. However, it remains unclear whether calcineurin dephosphorylates Cav3.2, the specific spatial regions on Cav3.2 involved, and the extent of the quantitative impact. In this study, we elucidated the serine/threonine residues on Cav3.2 targeted by calcineurin using quantitative mass spectrometry. We identified six serine residues in the N-terminus, II-III loop, and C-terminus of Cav3.2 that were dephosphorylated by calcineurin. Notably, a higher level of dephosphorylation was observed in the Cav3.2 C-terminus, where calcineurin binds to this channel. Additionally, a previously known CaMKII-phosphorylated site, S1198, was found to be dephosphorylated by calcineurin. Furthermore, we also discovered that a novel CaMKII-phosphorylated site, S2137, underwent dephosphorylation by calcineurin. In CAD cells, a mouse central nervous system cell line, membrane depolarization led to an increase in the phosphorylation of endogenous Cav3.2 at S2137. Mutation of S2137 affected the calcium channel function of Cav3.2. Our findings advance the understanding of Cav3.2 regulation not only through kinase phosphorylation but also via calcineurin phosphatase dephosphorylation.

Background: Wheat root rot disease due to soil-borne fungal pathogens leads to tremendous yield losses worth billions of dollars worldwide every year. It is very important to study the relationship between rhizosphere fungal diversity and wheat roots to understand the occurrence and development of wheat root rot disease. Results: A significant difference in fungal diversity was observed between the diseased and healthy groups in the heading stage, but the trend was the opposite in the filling stage. The abundance of most genera with high richness decreased significantly from the heading to the filling stage in the diseased groups; the richness of approximately one-third of all genera remained unchanged, and only a few low-richness genera, such as Fusarium and Ceratobasidium, had a very significant increase from the heading to the filling stage. In the healthy groups, the abundance of most genera increased significantly from the heading to the filling stage; the abundance of some genera did not change markedly, or the abundance of very few genera increased significantly. Physical and chemical soil indicators showed that low soil pH and density, increases in ammonium nitrogen, nitrate nitrogen and total nitrogen contributed to the occurrence of wheat root rot disease. Conclusions: Our results revealed that in the early stages of disease, highly diverse rhizosphere fungi and a complex community structure can easily cause wheat root rot disease. The existence of pathogenic fungi is a necessary condition for wheat root rot disease, but the richness of pathogenic fungi is not necessarily important. The increases in ammonium nitrogen, nitrate nitrogen and total nitrogen contributed to the occurrence of wheat root rot disease. Low soil pH and soil density are beneficial to the occurrence of wheat root rot disease.

Longitudinal cutting is a most common process in steel structure manufacturing, and the man-hours of the process provide an important basis for enterprises to generate production schedules.However, currently the man-hours in factories are mainly estimated by experts, and the accuracy of this method is relatively low.In this study,we propose a system that predicts man-hours with history data in the manufacturing process and that can be applied in practical structural steel fabrication.The system addresses the data inconsistency problem by one-hot encoding and data normalization techniques,Pearson correlation coefficient for feature selection,and the Random Forest Regression(RFR) for prediction.Compared with the other three Machine Learning(ML) algorithms, the Random Forest algorithm has the best performance.The results demonstrate that the proposed system outperforms the conventional approach and has better forecast accuracy, so that it is suitable for man-hours prediction.

Currently, active and intelligent packaging have been developed to solve the spoilage problem for rich protein foods during storage, especially by adding anthocyanin extracts. In such film system, the antioxidant and antibacterial properties were dramatically increased by adding anthocyanins. The physicochemical properties were enhanced through interactions between active groups in anthocyanins and reactive groups in polymer chains. Additionally, active and intelligent film could monitor the spoilage of rich protein foods in response to pH change. Therefore, this film could monitor the sensory acceptance, and extending the shelf life of rich protein foods simultaneously. In this paper, the structure and functional properties of anthocyanins, the composite actions of anthocyanin extracts and biomass materials, and their reinforced properties of active and intelligent film were discussed. Also, the applications of this film in quality maintenance, shelf-life extension and quality monitoring for fresh meat, aquatic product and milk were summarized. The film that achieves high stability and continuous release of anthocyanins on demand will become an underlying trend in packaging applications for rich protein foods.

Monocarboxylate transporter 8 (MCT8) and organic anion-transporting polypeptide 1C1 (OATP1C1) are thyroid hormones (TH) transmembrane transporters relevant for the availability of TH in neural cells, crucial for their proper development and function. Mutations in MCT8 or OATP1C1 result in severe disorders with dramatic movement disability related to alterations in basal ganglia motor circuits. Mapping the expression of MCT8/OATP1C1 in those circuits is necessary to explain their involvement in motor control. We studied the distribution of both transporters in the neuronal subpopulations that configure the direct and indirect basal ganglia motor circuits using immunohistochemistry and double/multiple labeling immunofluorescence for TH transporters and neuronal biomarkers. We found their expression in the medium-sized spiny neurons of the striatum (the receptor neurons of the corticostriatal pathway), and in various types of its local microcircuitry interneurons, including the cholinergic. We also demonstrate the presence of both transporters in projection neurons of intrinsic and output nuclei of the basal ganglia, motor thalamus and nucleus basalis of Meynert, suggesting an important role of MCT8/OATP1C1 for modulating the motor system. Our findings suggest that a lack of function of these transporters in the basal ganglia circuits would significantly impact motor system modulation, leading to clinically severe movement impairment.

The regulation of intracellular pH in yeast (Saccharomyces cerevisiae) cells is critical for cell function and viability. In yeast, protons (H+) can be excreted from cell by the plasma membrane ATPase Pma1 and pumped into vacuoles by the vacuolar H+-ATPase. Because Pma1 is critical to the survival of yeast cells, it is unknown whether other compensatory components are involved in the pH homeostasis in the absence of Pma1. To elucidate how intracellular pH is regulated independently of Pma1, we employed a screening approach by exposing the yeast haploid deletion mutant library (ver 4.0) to the selective plant plasma membrane H+-ATPase inhibitor PS-1, which we previously reported. After repeated screenings and verification, we identified two proteins, ALY1 and ALY2, that play a role in the regulation of intracellular pH when Pma1 is deficient. Our research uncovers a new perspective on the regulation of intracellular pH related to Pma1 and also preliminarily reveals a role for ALY1 and ALY2 in the regulation of intracellular pH.

Prosocial behavior is vital for positive social development among adolescents, contributing to improved peer relationships, emotional well-being, and social competence. Gratitude, a positive emotion arising from recognizing and appreciating benefits received from others, has been identified as a potential contributor to adolescent prosocial behavior. This study aimed to investigate the mediating roles of social support and basic psychological needs in the relationship between gratitude and prosocial behavior among adolescents. A total of 390 middle school students participated in a longitudinal study, completing questionnaires assessing gratitude, social support, basic psychological needs, and prosocial behavior at two time points with a six-month interval. The results indicated that gratitude positively correlated with social support, basic psychological needs, and prosocial behavior. Structural equation modeling revealed that social support and basic psychological needs partially mediated the relationship between gratitude and adolescent prosocial behavior. Moreover, a chain-like mediation effect was observed, wherein social support influenced basic psychological needs, which in turn predicted prosocial behavior. These findings emphasize the importance of gratitude in fostering prosocial behavior among adolescents and highlight the mediating roles of social support and basic psychological needs in this relationship.

Foxtail millet (Setaria italica) is an important cereal crop with rich nutritional value. Distinctness, Uniformity, and Stability (DUS) are the prerequisites for the application of new variety rights for foxtail millet. In this study, we investigated 32 DUS test characteristics of 183 foxtail millet resources, studied their artificial selection trends, and identified varieties that conform to breeding trends. The results indicated significant differences in terms of means, ranges, and coefficients of variation for each characteristic. Correlation analysis was performed to determine the correlations between various DUS characteristics. Principal component analysis was conducted on 31 test characteristics to determine their primary characteristics. By plotting PC1 and PC2, all germplasm resources could be clearly distinguished. Trends in foxtail millet breeding were identified through differential analysis of DUS test characteristics between landrace varieties and cultivated varieties. Based on these breeding trends, optimal solution types for multiple evaluation indicators were determined; weight allocation was calculated, and a specific TOPSIS algorithm was designed to establish a comprehensive multi-criteria decision-making model. Using this model, the breeding potential of foxtail millet germplasm resources was ranked. These findings provided important reference for foxtail millet breeding in future.

Thorough and precise gene structure annotations are essential for maximizing the benefits of genomic data and unveiling valuable genetic insights. The cucumber genome was first released in 2009 and updated in 2019. To increase the accuracy of predicted gene models, 64 published RNA-seq data and 9 new strand-specific RNA-seq data from multiple tissues were used for manual comparison with the gene models. The updated annotation file (version 2.0) contains increased 24,145 predicted genes from previous version (24317 genes) with a higher BUSCO value of 96.9%. 6231 and 1490 transcripts were adjusted and newly added, respectively, accounting for 31.99% of the overall gene tally. These newly added and adjust genes were renamed (CsaV3.1_XGXXXXX), while genes remaining unaltered preserve their original des ignations. A random selection of 21 modified/added genes were validated using RT-PCR analyses. Additionally, tissue-specific patterns of gene expression were examined using newly obtained transcriptome data with the revised gene prediction model. This improved annotation of cucumber genome will provide essential and accurate resources for studies in cucumber.

Numerous studies have demonstrated that multiple intrinsic and extrinsic factors shape the structure and composition of gut microbiota in a host. The disorder of gut microbiota may trigger various host diseases. Here, we collected fecal samples from wild-caught Japanese geckos (Gekko japonicus) and captive conspecifics fed with mealworms (mealworm-fed geckos) and fruit flies (fly-fed geckos), aiming to examine dietary and sexual correlates of gut microbiota. We used the 16S rRNA gene sequencing technology to determine the composition of gut microbiota. The dominant phyla with a mean relative abundance higher than 10% were Verrucomicrobiota, Bacteroidota and Firmicutes. Gut microbial community richness was higher in mealworm-fed geckos than in fly-fed and wild geckos, and community diversity was higher in mealworm-fed geckos than in wild geckos. Neither alpha nor beta diversity of gut microbiota differed among wild, mealworm-fed and fly-fed geckos. The beta rather than alpha diversity of gut microbiota was sex-dependent. Based on the relative abundance of gut bacteria and its gene functions, we concluded that gut microbiota contributed more significantly to the host’s metabolic and immune functions. Higher diversity of gut microbiota in mealworm-fed geckos could result from higher chitin contents of insects of the order Coleoptera. This study not only provides basic information about the gut microbiota of G. japonicus, but also shows that gut microbiota correlates with dietary habit and sex in the species.

We fabricated high-quality MAPbBr3 single crystals (SC) by introducing moderate amount electron-rich poly(propylene glycol bis(2-aminopropyl ether) (PEA) additives with an inverse temperature crystallization (ITC) method. The intramolecular vibrations and defective states of prepared MAPbBr3 single crystals were systemically studied by the in situ variable-temperature Fourier Transform Infrared (FTIR) Spectroscopy, X-ray photoelectron spectroscopy (XPS), and the synchrotron-based X-ray absorption near edge structure (XANES), et al. We infer that the proper amount of PEA additives would prevent the formation of intermediate states and crystal boundaries, passivating the density of defective states. The X-ray detection properties of single-crystal MAPbBr3 crystals were investigated, using both high dose and low dose X-ray photons at 40keV in synchrotron beamlines. The photocurrent of optimized PEA-treated MAPbBr3 single crystals demonstrate better performance compared with the as-prepared single crystals. Meanwhile, the decay time of MAPbBr3 single crystal is decreased from 460 ns to 210 ns by Time-resolved photoluminescence (TRPL) decay measurement, owing to the defect passivation by 0.5wt% PEA additives. The PEA-treated single crystals possess much faster decay time than the commercialized Ce:YAG scintillator (>500ns). These results help elucidate the passivation of defective states and contribute paths to manufacture high-quality single crystal perovskites for next-generation optoelectronic devices.

The origin of neurodegenerative diseases is linked to the abnormal folding of disease-associated proteins. The traditional amyloid hypothesis has been a focal point of research, but recent findings suggest a more complex picture. This review explores the role of physiological conformation of aggregation-prone domain (also known as prion-like low complexity domain) and multiple co-misfolded proteins in neurodegenerative diseases. We highlight the importance of targeting multi-heterotypic misfolded proteins for effective treatments and emphasize the irreversible neurodegeneration stemming from the loss of physiological folding in prion-like disease-causing proteins underscores the criticality of refolding. Additionally, we introduce the concept of ReproFold Therapeutics, a novel approach aimed at restoring the cellular prion-like folding of disease-causing proteins to rebuild normal cross-β interactomes and mitigate neurodegeneration. Baicalein, a potential drug candidate for this approach, shows promise in vitro and in animal models. Moreover, prion-like low complexity domains implicated in neurodegeneration are also associated with other disorders such as diabetes, cancers, and mental illnesses. Understanding the core pathology of neurodegenerative diseases and the broader implications of prion-like LC domains could revolutionize healthcare approaches and policies worldwide.