Hydrogen storage in high pressure tanks can occur with different filling strategies. Many studies have been carried out on supplies with increasing pressure rates. However, hydrogen filling with constant mass inflow rate have not received the same attention. The present work aims to carry out numerical simulations to study hydrogen flow, in a type 3 tank of 70 MPa NWP and constant inflow rate condition. From the analysis of the results, it was possible to verify that there is a linear relationship between the increase in the total equilibrium temperature and the final hydrogen temperature. There is also a linear increasing relationship between Inlet and final temperatures when the equilibrium temperature is fixed. Considering fully adiabatic walls results in significant increases in temperature. The difference between total and static temperatures found in the Inlet tube decreases with the decrease in mass flow rate. The choice of a polymer for the tank lining led to higher temperatures when compared to an aluminum lining.

The aim of this study was to assess precipitation (P) by analyzing data from in situ stations compared with those from solely remote sensing products CHIRP and CMORPH, with a reference station in the city. The evapotranspiration (ET) was analyzed directly using SSEBop. The region chosen for this study was the Metropolitan Area of Belem (MAB), close to the estuary of the Amazon River and the mouth of the Tocantins River. Belem is the rainiest state capital of Brazil, which causes a myriad of problems for the local population. The monthly best fit is shown here. In this study, we analyzed P and ET from local stations and compared them with those from satellite products. The main metrics RMSE, NRMSE, MBE, R2, Slope, and NS were used. For the reference station, the automatic and conventional CHIRP and CMORPH results, in mm/month, were as follows: automatic CHIRP: RMSE = 93,3, NRMSE = 0.32, MBE = −33,54, R2 = 0.7048, Slope = 0.945, NS = 0.5668; CMORPH: RMSE = 195,93, NRMSE = 0.37, MBE = −52,86, R2 = 0.6731, Slope = 0.93, NS = 0.4344; conventional station CHIRP: RMSE = 94.87, NRMSE = 0.32, MBE = −33.54, R2 = 0.7048, Slope = 0.945, NS = 0.5668; CMORPH: RMSE = 105.58, NRMSE = 0.38, MBE = −59.46 R2 = 0.7728, Slope = 1.007, NS = 0.4308. This was compared with the pixel and in situ station data. The ET ranges, on average, between 83 mm/month in the Amazonian summer and 112 mm/month in the Amazonian winter. This work concludes that, although CMORPH has a coarser resolution of 0.25° compared to CHIP’s 0.05° for MAB at a monthly resolution, the remote sensing products were reliable. SSEBop also showed reliable performance. For analyses of the consistency of precipitation time series, these products could provide more accurate information.

The Eurasian grapevine (Vitis vinifera L.) is the most widely grown horticultural crop in the world and is important for the economy of many countries. In the wine production chain, grape varieties play an important role as they directly influence the authenticity and classification of the product. Identifying the different grape varieties is therefore fundamental for quality control and inspection activities, as well as for regulating production. Currently, ampelography and molecular analysis are the main approaches to identifying grape varieties. However, both methods have limitations. Ampelography is subjective and prone to errors and is experiencing enormous difficulties as ampelographers are increasingly scarce. On the other hand, molecular analyses are very demanding in terms of cost and time. In this scenario, Deep Learning (DL) and Machine Learning (ML) methods have emerged as a classification alternative to deal with the scarcity of ampelographs and avoid molecular analyses. In this study, the most recent and current methods for identifying grapevine varieties using DL classification-based approaches are presented through a systematic literature review. The classification pipeline of the 31 studies found in the literature was described, highlighting its pros and cons. Most of the studies used DL-based models trained with leaf images acquired in a controlled environment at a maximum distance of 1.2 metres to classify grape varieties. In addition, there is a large gap between practical applications and the datasets used: a great lack of varieties, limited data acquired in the field and a lack of tests on plants under adverse conditions. Potential directions for improving this area of research were also presented.

Urban mobility is experiencing a profound change. On the one hand, mobility patterns are becoming more complex, and typical home-work-home travel is no longer the rule, as journeys now tend to connect multiple points in a rather inconstant pattern. This has changed the approach to transport planning, in that the existing transportation planning and operation approaches have been focussed on the ability to identify typical home-work/school-home travel and subsequently plan the transport system accordingly. The traditional approach has been: forecast -> plan -> deliver, as new mobility solutions are emerging. These are characterised by greater flexibility, in that they take advantage of the “sharing concept” and simultaneously provide solutions that have lower GHG emissions. Urban mobility follows a fuzzier pattern, with even the urban transportation system behaving like an active organism, where solutions are often quickly replaced. This dynamic and evolving environment raises several new challenges at different levels. The best digital solution system is the Mobility-as-a-Service (MaaS) one. This system transforms the physical transportation system into a commodity and takes advantage of the internet of things (IoT). However, the onset of MaaS solutions is anything but linear. Several business models have emerged, with different partners originating from different industries (e.g., technological, transport operators, infrastructure managers, etc.) developing their own solutions, often in competition with others. It is not unusual to find different MaaS solutions in the same city, which integrate different solutions.

Reducing under-five mortality is a key indicator of a country's overall development, yet in Angola, understanding the factors contributing to hospital deaths in this vulnerable demographic remains incomplete despite improvements in healthcare infrastructure and public health policies. With one of the highest under-five mortality rates in Sub-Saharan Africa, Angola grapples with significant challenges, including malaria, malnutrition, pneumonia, neonatal conditions, and intestinal infectious diseases, as leading causes of death among children. This study aimed to identify factors associated with these hospital deaths in children aged 28 days to five years admitted to DBPH in Luanda between May 2022 and June 2023. Utilizing a hospital-based case-control design, a total of 1020 children were studied, with 340 cases of hospital deaths. Notably, distal and intermediate determinants emerged as primary predictors of hospital mortality, revealing significant associations with maternal education status, maternal alcohol consumption during pregnancy, short hospital stays (≤24h), poor nutritional status, short interbirth intervals, maternal age ≤19 years, and maternal age ≥35 years. These findings underscore the preventable nature of most under-five hospital deaths and emphasize the urgent need to address social inequities and enhance the quality of primary healthcare services to effectively mitigate child mortality.

Agriculture is the main economic activity of Mozambique and there is lack of information about the quality of agricultural soils. In this paper, five soils from the Manica and Sussudenga districts (Manica province) were sampled in the years 2021/2022 and 2022/2023 (before and after the rainy seasons), were subjected to an agronomical and environmental chemical analysis to assess its quality, either from the fertility and environmental contamination point of view. Standard analytical methodologies from external certified laboratories and local X-ray fluorescence measurements were used. All the studied soils are acidic (pH ranging from 4.5 and 5.4), have no salinity problems (conductivity ranging from 4.2 to 11.8 mS/m), have low amount of soil organic matter (0.90% to 1.81%), and soils from the Sussudenga district have a very low cation exchange capacity (CEC) (average of 3.33 cmolc/kg), while those from Manica district ranges from very low to average CEC (3.59 to 13.11 cmolc/kg). Also, Sussudenga soils have a phosphorous deficiency (values ranging from <20 to 38.5 mg/kg) and there are deficiencies and/or excesses of some macro and micronutrients in all soil samples. Manica soils are contaminated, apparently from geogenic origin, with Cr (280 to 1400 mg/kg), Co (80 mg/kg), Ni (78 to 680 mg/kg) and V (86 mg/kg). Agricultural soils monitoring must be fostered in Mozambique in order to improve food quality and quantity to assure economic and environmental sustainability.

Data creation is often the only way for researchers to produce basic geospatial information for the pursuit of more complex tasks and procedures such as those that lead to the production of new data for studies concerning river basins, slope morphodynamics, applied geomorphology and geology, urban and territorial planning, detailed studies, for example, in architecture and civil engineering, among others. This exercise results from a reflection where specific data processing tasks executed in Google Sketchup (Pro version, 2018) can be used in a context of interoperability with Geographical Information Systems (GIS) software. The focus is based on the production of contour lines and Digital Elevation Models (DEM) using an innovative sequence of tasks and procedures in both environments (GS and GIS). It starts in Google Sketchup (GS) graphic interface, with the selection of a satellite image referring to the study area—which can be anywhere on Earth's surface; subsequent processing steps lead to the production of elevation data at the selected scale and equidistance. This new data must be exported to GIS software in vector formats such as Autodesk Design Web format—DWG or Autodesk Drawing Exchange format—DXF. In this essay the option for the use of GIS Open Source Software (gvSIG and QGIS) was made. Correcting the original SHP by removing “data noise” that resulted from DXF file conversion permits the author to create new clean vector data in SHP format and, at a later stage, generate DEM data. This means that new elevation data becomes available, using simple but intuitive and interoperable procedures and techniques which confgures a costless work flow.

Mozambique is one of the poorest countries of the world. However, it has natural resources and if they are managed under sustainable development principles, Mozambique can overcome the current problems. In the present socio-economic status, soil is one of its most important resources and must be protected from pollution and from degradation. This review focuses on the identification and discussion of the main soil quality stressors, namely: soil fertility; deforestation and its sources: agriculture, timber harvesting, charcoal production and uncontrolled fires; mining activities, manly gold artisanal explorations and industrial open-pit coal mining. The sustainable use of the natural resources is mandatory to allow future generations to continue profiting for this nature-based wealth.

Recent advances in embedded antenna and sensor technologies for 5G communications have galvanized a response toward the investigation of their electromagnetic (EM) performance for urban context and civil engineering applications. This article quantitatively investigates the effects of material loading on an evolved antecedent-based design of a hexagonal-stubbed Complementary Split-Ring Resonator (CSRR)-loaded antenna through simulation and experimentation. The optimized antenna design is first conceptualized within a simulation environment to achieve EM resonance at 3.50 GHz before delving into the analysis of operational performance characteristics. As a proof-of-concept, a physical antenna prototype is fabricated on a printed circuit board for the in-situ evaluation of S11 parameter plot. Subsequently, a simulation-based parametric study is conducted on antenna prototypes embedded into Ordinary Portland Cement pastes with varying weight percentages of iron(III) oxide. Simulation-derived and experimental results are mutually verified, achieving a systemic downward shift in resonant frequency and corresponding variations in impedance matching induced by changes in the loading reactance. Finally, an inversion modeling procedure is employed using perturbation theory to extrapolate the relative permittivity of the dielectric embedding materials. Our proposed analysis contributes to optimizing concrete-embedded 5G antenna sensor designs and establishes a foundational framework for estimating unknown EM parameters of cement-based composites.

Spatial modeling in Geographic Information Systems (GIS) always involves choices. The existence of constraints, either of a financial nature or related to the specifics of the software itself, to the algorithms, the uncertainty and even the reliability of the data, the purposes and the applications of the studies, make this a kind of guiding compass for GIS analysts. Building on a previous exercise of data acquisition (check-ins) based on two Digital Social Networks (DSN — Facebook and Foursquare) and on the awareness of the use of Volunteered Geographic Information (VGI) generated by tourists sharing their topophilic ties through DSN, the present analysis aims to evaluate the contribution of modern techniques of spatial analysis applied to tourism in the “Alta and University of Coimbra” area. Concepts and procedural tasks related to density determination, cluster analysis and identification of patterns associated with regionalized variables have thus been implemented with the purpose of evaluating and comparing the results obtained through the application of two techniques of spatial analysis, Kernel Density Estimation (KDE) and Optimized Hot-Spot Analysis (OHSA) & Inverse Distance Weighting (IDW) Interpolation.

Regional heterogeneity of microglia was first described a century ago by Pio del Rio Hortega. Currently, new hints on microglia heterogeneity across central nervous system (CNS) regions are still being unraveled by high-throughput techniques. It remains unclear whether these spatial specificities translate into different microglial behaviors in vitro. We cultured microglia isolated from the cortex and spinal cord and analyzed the effect of the CNS spatial source on in vitro behavior by applying the same experimental protocol and culture conditions. We analyzed microglial cell numbers, function, and morphology and found a distinctive in vitro phenotype. We found that microglia were present in higher numbers in spinal cord-derived glial cultures, presenting different expression of inflammatory genes and a lower phagocytosis rate under basal conditions or after activation with LPS and IFN-. Morphologically, cortical microglial cells are more complex and present longer ramifications, which were also observed in vivo in CX3CR1+/GFP transgenic reporter mice. Collectively, our data demonstrated that microglial behavior in vitro is defined according to specific spatial characteristics acquired in the tissue. Thus, our study highlights the importance of microglia as a source of CNS for in vitro studies.

In recent decades, the creation and availability of Voluntary Geographic Information (VGI) has changed the paradigm associated with the production of Geospatial Information (GI), since due to its free access, citizens can view, analyse, process, and validate this type of data. One of the most popular examples of VGI is the collaborative OpenStreetMap (OSM) project which covers a wide range of themes or characteristics associated with the real world. One of these themes is the feature “waterway” that represents watercourses. The quality of OSM data characteristics is an issue that has been published by many authors in recent years, particularly on the analysis of the completeness indicator. However, few references are found in literature to studies that analyse the completeness of OSM watercourses. This study presents an analysis of the variation over time in completeness/coverage of the OSM "waterway" feature in the epochs of 2014 and 2023 in a mountainous region included in the Mondego River basin, located in Inland of Portugal. The results show that the completeness of this OSM feature (waterway) has a slight increase, considering the amplitude of this period (nine years) and the fact that, nowadays, digital mobile devices enable access to satellite images, therefore allowing in an easy way the digitalization of entities or objects of the real world remotely. Regarding the indicator’s altitude, slope and location/proximity of settlements, it was not possible to observe their influence on the evolution of the completeness of this geographic entity (OSM waterway).

Genetic testing allows for identification of germline DNA variations which are associated with a significant increase in risk of developing breast and ovarian cancer. Detection of a BRCA1 or BRCA2 pathogenic variant triggers several clinical management actions, which may include increased surveillance and prophylactic surgery for healthy carriers or treatment with PARP inhibitor therapy for carriers diagnosed with cancer. Thus, standardized validated criteria for annotation of BRCA1 and BRCA2 variants according to their pathogenicity are necessary to support clinical decision making and ensure improved outcomes. Upon detection, variants whose pathogenicity can be inferred by the genetic code are typically classified as pathogenic, likely pathogenic, likely benign, or benign. Variants whose impact on function cannot be directly inferred by the genetic code are labeled as Variants of Uncertain Clinical Significance (VUS) and are evaluated by multifactorial likelihood models that use personal and family history of cancer, segregation data, prediction tools, and co-occurrence with a pathogenic BRCA variant. Missense variants, coding alterations that replace a single amino acid residue with another, are a class of variants for which determination of clinical relevance is particularly challenging. Here, we discuss current issues in variant classification by following a typical life cycle of a BRCA1 missense variant through detection, annotation and information dissemination. Advances in massively parallel sequencing have led to a substantial increase in VUS findings. Although comprehensive assessment and classification of missense variants according to their pathogenicity remains the bottle neck, new developments in functional analysis, high throughput assays, data sharing, and statistical models are rapidly changing this scenario.

Recent studies have reported shallow and deep seep areas offshore Mocha island. Gas hydrate occurrences along the Chilean margin could explain seeps presence. Gas phases (gas hydrate and free gas) and geothermal gradients were estimated analysing two seismic sections. Close to Mocha island (up to 20 km) were detected high (up to 1900 m/s) and low (1260 m/s) velocities associated with high gas hydrate (up to 20 % of total volume) and free gas (up to 1.1% of total volume) concentrations respectively. These values are in agreement with a variable and high geothermal gradient (65 to 110 °C/km) related to high supply deep fluids canalised by faults and fractures. Faraway from Mocha island (more than 60 km), free gas concentrations decrease to 0.3 % of total volume and low geothermal gradient (from 35 to 60 °C/km) are associated with low fluids supply. Finally, we propose gas hydrate dissociation processes as the main supply source for seeps in the vicinity of Mocha island. These processes can be triggered by ancient sliding reported in literature.

This work describes a method to carry out 2-D inversion of gravity data in terms of porosity and matrix density distribution using previous DC resistivity inversion results to constraint the fractional pore-water content in the rocks. The inversion is carried out using a controlled random search (CRS) algorithm for global optimization. The method was tested on synthetic data generated from a model representing a graben, and the results show that it can estimate accurate values of contrast-density and porosity. The method was also applied to gravity and dc experimental data collected in NE Portugal, showing results that agree quite well with the known geological information.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

Preliminaries Convolutional Neural Network (CNN) applications have recently emerged in Structural Health Monitoring (SHM) systems focusing mostly on vibration analysis. However, the SHM literature shows clearly that there is a lack of application regarding the combination of PZT (Lead Zirconate Titanate) based method and CNN. Likewise, applications using CNN along with the Electromechanical Impedance (EMI) technique applied to SHM systems are rare. To encourage this combination, an innovative SHM solution through the combination of the EMI-PZT and CNN is presented here. To accomplish this, the EMI signature is split into several parts followed by computing the Euclidean distances among them to form a RGB (red, green and blue) frame. As a result, we introduce a dataset formed from the EMI-PZT signals of 720 frames, encompassing a total of 4 types of structural conditions for each PZT. In a case study, the CNN-based method was experimentally evaluated using three PZTs glued onto an aluminum plate. The results reveal an effective pattern classification; yielding a 100% hit rate which outperforms other SHM approaches. Furthermore, the method needs only a small dataset for training the CNN, providing several advantages for industrial applications.

Spatial modeling in Geographic Information Systems (GIS) always involves choices. The existence of constraints, either of a financial nature or related to the specifics of the software itself, to the algorithms, the uncertainty and even the reliability of the data, the purposes and the applications of the studies, make this a kind of guiding compass for GIS analysts. Building on a previous exercise of data acquisition (check-ins) based on two Digital Social Networks (DSN—Facebook and Foursquare) and on the awareness of the use of voluntary geographic information generated by tourists sharing their topophilic ties through DSN, the present analysis aims to evaluate the contribution of modern techniques of spatial analysis applied to tourism in the “Alta and University of Coimbra” area. Concepts and procedural tasks related to density determination, cluster analysis and identification of patterns associated with regionalized variables have thus been implemented with the purpose of evaluating and comparing the results obtained through the application of two techniques of spatial analysis, Kernel Density Estimation (KDE) and Optimized Hot-Spot Analysis (OHSA) & Inverse Distance Weighting (IDW) Interpolation.

Most research on colostrum quality and colostrum management focuses on maternal IgG transfer to the newborn calf. However, in addition to being a source of antibodies, colostrum has other components that influence passive immune transfer, nutrition, gut maturation, and thermoregulation. In this review, the constituents in the bovine colostrum, as well as their variation, are explored and it is discussed the biological role of colostrum on the newborn calf. Protein is the nutrient in higher concentration and fat is the nutrient with the most variation. There is a pronounced amplitude in the total solids content of colostrum, but the average concentration does not vary much between studies (24.7%). Bovine colostrum major components can vary with several factors, such as the region, season, breed, dry period length, and nutritional aspects of the dam. Bioactive components, cells, and microbiome variability are less understood, besides IgG. Regardless, they play crucial distinct roles in the physiological development of the newborn. However, a multi-interactive effect between these components, cells, and microorganisms is more likely to occur. Recently researched components in colostrum like miRNA, nucleo(t)sides, the milk fat globule membrane, oligosaccharides, minor proteins, and the microbiome are examples of promising interest areas of study.

The ultimate goal of this paper was to examine the degree of elasticity between two variables, namely, agricultural credit and agricultural growth, in Angola in the period 2003–2022. Time series data were fitted into the ARDL test using various econometric techniques such as the ADF stationarity test, Granger causality and the ordinary least squares method as well as a vector error correction model (VECM) to analyze the relationship between agricultural credit and agricultural economic growth, showing a causal relationship. Both the impacts through elasticities and the optimal point existing in this relationship were estimated. It was concluded that the impact of agricultural credit on agricultural GDP was 14.41%. Granger causality shows signs of a positive linkage between agricultural credit and agricultural GDP. However, there is a causal relationship between agricultural credit and agricultural GDP, in a unidirectional aspect. This result is consistent with most of the earlier studies reviewed in the literature, confirming that credit-oriented monetary policies can boost economic growth and, consequently, development in Angola. It is important for agricultural credit systems to be designed in a way that ensures equitable access, fair interest rates, and appropriate risk management mechanisms. Additionally, monitoring and evaluation mechanisms should be in place to assess the environmental and social impacts of credit programs on agricultural sustainability. It is worth noting that this is a first-of-a-kind study on the matter of the Angolan credit experience, specifically for the agricultural sector. Angola is still searching for a sustainable credit model that could be used as a catalyzer to boost growth and contribute to economic development.

In California, water is a perennial concern. As competition for water resources increases due to growth in population, California’s tree nut farmers are committed to improving the efficiency of water used for food production. There is an imminent need to have reliable methods that provide information about the temporal and spatial variability of crop water requirements, which allow farmers to make irrigation decisions at field scale. This study focuses on estimating the actual evapotranspiration and crop coefficients of an almond and pistachio orchard located in Central Valley (California) during an entire growing season by combining a simple crop evapotranspiration model with remote sensing data. A dataset of the vegetation index NDVI derived from Landsat-8 was used to facilitate the estimation of the basal crop coefficient (Kcb), or potential crop water use. The soil water evaporation coefficient (Ke) was measured from microlysimeters. The water stress coefficient (Ks) was derived from airborne remotely sensed canopy thermal-based methods, using seasonal regressions between the crop water stress index (CWSI) and stem water potential (Ystem). These regressions were statistically-significant for both crops, indicating clear seasonal differences in pistachios, but not in almonds. In almonds, the estimated maximum Kcb values ranged between 1.05 to 0.90, while for pistachios, it ranged between 0.89 to 0.80. The model indicated a difference of 97 mm in transpiration over the season between both crops. Soil evaporation accounted for an average of 16% and 13% of the total actual evapotranspiration for almonds and pistachios, respectively. Verification of the model-based daily crop evapotranspiration estimates was done using eddy-covariance and surface renewal data collected in the same orchards, yielding an r² >= 0.7 and average root mean square errors (RMSE) of 0.74 and 0.91 mm day^-1 for almond and pistachio, respectively. It is concluded that the combination of crop evapotranspiration models with remotely-sensed data is helpful for upscaling irrigation information from plant to field scale and thus may be used by farmers for making day-to-day irrigation management decisions.

A large share of the reinforced concrete (RC) building stock in Mediterranean countries faces a dual challenge of seismic vulnerability and energy inefficiency, calling for urgent renovation efforts. While energy upgrades have been the focus of previous renovation policies, recent research highlights the critical need for integrated retrofitting solutions that address both structural integrity and energy performance. Multi-criteria decision-making (MCDM) approaches are a promising tool for optimizing the combined choice of these integrated interventions, considering various decision variables (DVs) of economic, social, environmental, and technical nature. To understand the impact of climate and seismic hazard conditions on multi-criteria-based retrofitting assessment, a case-study RC school building is selected and assumed to be located in three distinct climate conditions, cold, mild, and warm, and three seismic hazard levels, low, medium and high. Moreover, given the complexity and challenges of quantifying seismic performance metrics for practitioners, an available simplified (practice-oriented) approach is compared herein with a more thorough research-based one for quantifying the seismic performance of RC buildings within the MCDM framework. Both approaches are applied to the case-study building, considering twelve possible combinations of energy and seismic interventions. The accuracy of the practice-oriented approach and its impact on the retrofitting rankings is evaluated, emphasizing the importance of accessible and efficient evaluation methods in facilitating informed decision-making for building renovation

Keywords: Wood residuals; Forest biomass; Wood composite; Wood floor; Life Cycle Assessment.

This review focus on a critical analysis of nanocatalysts for Advanced Reductive Processes (ARP) and Oxidation Processes (AOP) designed for the degradation of poly/perfluoroalkyl substances (PFAS) in water. Ozone, ultraviolet and photocatalyzed ARP and/or AOP will be the basic treatment technologies. Besides the review of the nanomaterials with greater potential as catalyst for advanced processes of PFAS in water, the perspectives for its future development considering sustainability considerations will be discussed. Moreover, a brief analysis of the current state of the art of the ARP and AOP for the treatment of PFAS in water will be presented.

This paper aims to assess whether the financial performance of Portuguese companies that publish sustainability reports (SR) differs from the financial performance of companies that do not publish SR. We use two methodological procedures. First, we conducted a univariate analysis to test the differences in the financial performance according to the disclosure of SR. Second, we conducted a multivariate analysis using a multiple linear regression that explains financial performance by the disclosure of SR, as well as control variables such as sector, size, leverage, growth, and liquidity. Findings indicate that financial performance of companies that disclose SR does not significantly differ from the financial performance of companies that do not disclose SR. The results are robust to both methodological procedures, as well as to the sample split by sectors.

The conditions for safe Internet access and the development of skills enabling full participation in online environments are recognized in the Council of Europe’s strategy for child rights, from 2022. The guarantee of this right has implications for experiences inside and outside the school context. Therefore, this article aims to compare the perceptions of students from different educational levels, who participated in a digital storytelling workshop, regarding online safety, searching habits, and digital competences. Data were collected through a questionnaire survey completed by 84 Portuguese students from elementary and secondary schools. A non-parametric multivariate analysis of variance was used to identify differences as children advance across educational stages. The results revealed that secondary students tend to spend more time online, and demonstrated more advanced search skills. Interestingly, the youngest children exhibited higher competences in creating games and practicing safety measures regarding online postings. These findings emphasize the importance of schools, in a joint action with the educational community, including parents, teachers and students, developing a coordinated and vertically integrated approach to digital education that considers the children's current knowledge, attitudes, and skills as a starting point for pedagogical intervention.

Context: Code smells are associated with poor design and programming style that often degrades code quality and hampers code comprehensibility and maintainability. Goal: Identify reports from the literature that provide evidence of the influence of code smells on the occurrence of software bugs. Method: We conducted a Systematic Literature Review (SLR) to reach the~stated goal. Results: The SLR includes selected studies from July 2007 to September 2017 which analyzed the source code for open source and proprietary projects, as well, as several code smells and anti-patterns. The results of this SLR show that 24 code smells are more influential in the occurrence of bugs according to 16 studies. In contrast, three studies reported that at least 6 code smells are less influential in such occurrences. Evidence from the selected studies also point out tools, techniques and procedures applied to analyze the influence. Conclusion: To the best of our knowledge, this is the first SLR to target this goal. This study provides an up-to-date and structured understanding of the influence of code smells on the occurrence of software bugs based on findings systematically collected from a list of relevant references in the latest decade.

The Social Economy (SE) emerges as an interesting alternative to deal with social problems that often cannot be met by the services provided by the State. However, one of the concerns relates to the ability of these institutions to meet the demands of stakeholders concerning accountability. In this sense, the present work aimed to determine if the IPSS are prepared to meet the management requirements by increasing their accountability. For that purpose, we conducted qualitative research, with an exploratory focus, with 31 Portuguese Private Social Solidarity Institutions (IPSS). The interviews took place between June and July 2019, with those responsible for managing the entities. The interviews were guided on a semi-structured script based on the literature review. After Content Analysis, it was found that, in most of the institutions interviewed, the board does not use management tools, such as performance analysis, social impact assessment, strategic planning and quality management systems, even recognising the importance of using them. The fact is due to the lack of access or knowledge about its use. In addition, the majority of the IPSS interviewed showed concern about the transparency and ethics of managers. Current strategic management practices are remarkably targeted at companies in the for-profit sector and can compromise the principle of investments in human and social issues. Thus, the introduction of new activities can further reinforce the pressure felt by these institutions in carrying out operational activities.

Given the extreme importance of improving the accountability of Private Social Solidarity Institutions (IPSS), both for reasons of legal compliance (hard law) and for reasons of improving legitimacy and notoriety among their stakeholders (soft law), this paper aims to present a framework designed under a more comprehensive research project, for the assessment of IPSS accountability and, consequently, its improvement. This study also present results of the indicators conceived, identifying the main trends of the framework dimensions and sub-dimensions from a pilot test for the years 2018, 2019 and 2020 in Portugal. Given the results, we believe that the framework designed answers the research question: How to promote accountability (social, financial and economic) in the social economy sector, in particular: the case of the IPSS?, however, as this is an exploratory article, it incorporates the limitation that this is a pilot test with only 7 entities.

Social Economy institutions seek to provide answers to social problems, given that they naturally have a socially responsible mission. This study aims to answer the research question: how sustainable practices, namely environmental behaviour, have been adopted by Portuguese Private Social Solidarity Institutions (IPSS) with the purpose of contributing to Sustainable Development? To achieve this objective, qualitative research was carried out in 31 IPSS, which was framed within the scope of the TFA project (Theoretical framework for promotion of accountability in the social economy sector: the IPSS case). Semi-structured interviews were conducted, with a script based on the literature review, from May to July 2019, with those responsible for the management of these entities. A content analysis was conducted, using the NVivo12 Version 12.6.0 software, which enables data to be coded and categorised, reducing any researcher bias. The results indicate that most entities carry out activities of an environmental nature, related to the reuse of materials, the recycling of waste, the sale of materials for recycling, and user awareness. Several entities expressed financial limitations to the implementation of Environmental Management Systems and their accomplishment. However, the objections presented are not impossible to overcome, according to studies presented in other countries.

For the majority of the contractual arrangements used in construction projects, the owner is not responsible for the cost deviations due to the variability of labor productivity or material price, amongst many other aspects. Consequently, the cost performance of a project may be entirely distinct for the owner and the contractor. Since the majority of the quantitative research on cost estimation and deviation found in the literature adopts the owners’ perspective, this research provides a contribution towards modelling costs and cost deviation from a contractors’ perspective. From an initial sample of 13 residential building and 10 office building projects, it was possible to develop models for cost estimation at the early stage of development including both endogenous and exogenous variables. Although the sample is relatively small, the authors were able to fully analyze all the cost data, using no secondary sources of data (very frequent in cost modelling studies). The statistically significant variables in the cost estimation models were the areas above and below ground and the years following the 2008 financial crisis, including the international bailout (2011-2014) period. For estimating the unit cost, a nonlinear model was obtained with the number of underground and total floor, the floor ratio and the years following the 2008 financial crisis, including the international bailout (2011-2014) period as predictors. For the office buildings, it was also found a statistically significant correlation between the cost deviation and the number of underground floors.

The aim of this paper is to explore the watertightness behaviour for high pressure applications using Multijetfusion technology and polyamide 12 as a material. It reports an efficient solution for manufacturing functional prototypes and final parts for water pressure applications. It provides manufacturing rules to engineers in the pressurized product development process up to 10 MPa of nominal pressure. The research findings show manufacturers the possibility of using additive manufacturing as an alternative to traditional manufacturing. Water leakage was studied using different printing orientations and wall thickness for a range of pressure values. An industrial ball valve was printed and validated with the ISO 9393 standard also meeting tolerance requirements. This paper is a pioneering approach to the additive manufacturing of high performance fluid handling components. This approach solves the problem of leakage caused by porosity in additive manufacturing technologies

Green carbon-based materials (GCM), i.e. carbon materials produced using renewable biomass or recycled wastes, ought to be used in order to processes become sustainable and carbon neutral. Carbon nanomaterials, like for example carbon dots and nanobichar families, and carbon materials, like for example activated carbon and biochar substances, are sustainable materials with great potential to be used in different technology applications. In this review, the following four applications were selected, and the works published in the last two years (since 2022) critically reviewed: agriculture; water treatment; energy management; and, carbon dioxide reduction and sequestration. GCM improved the performance of the technological applications under revision and play an important role in the sustainability of the processes, contributing to the mitigation of the climate change, namely by reducing emission and increase sequestration of CO2eq..

Biomass-derived carbon dots (CDs) are gaining much interest in recent times as it is a sustainable option with abundant availability, low cost, and tunable luminescence. Herein, we report a simple green synthesis method to produce highly fluorescent CDs from Eucalyptus globulus leaves using the one-pot hydrothermal approach. The fabricated CDs exhibit strong blue fluorescence with an excitation and emission maxima of 340 nm and 442 nm respectively. The highest quantum yield (QY) obtained was 60.7%. Due to its promising optical properties and biocompatibility, CDs can be a potential candidate for biosensing applications. Moreover, we employed a life cycle assessment (LCA) cradle-to-gate approach to study the environmental impacts of the synthesis strategy used for the fabrication of CDs. The results point out that citric acid is a main hotspot in CDs synthesis, regarding environmental impacts in most categories. This justifies the introduction of biomass, which reduces the amount of citric acid, thus leading to a more sustainable synthesis strategy for fabricating CDs.

A sustainable matrix based on eucalyptol essential oil/sawdust was developed and applied on one-sided laminated plywood. This finish aims to serve as a eucalyptol odor slow release. Eucalyptol odor release was monitored with gas chromatography coupled with a flame ionization detector (GC – FID: Limits of Detection and Quantification of 0.70 g/m3 and 2.11 g/m3, respectively, and with linearity up to 18.6 g/m3). Measurement of the eucalyptol odor released was performed during a six-month period and it was found that the release followed a first-order exponential decay with a decay rate constant of 0.0169 per day. The half-life was determined to be of 48 days. The granulometry and particle size porosity of sawdust were analyzed by Scanning Electron Microscopy. Sawdust size fraction between 112 – 200 μm showed best eucalyptol absorption capacity with 1:3 masses ratio (sawdust:eucalyptol). The time capacity of eucalyptol release depends of composite eucalyptol – sawdust quantity. Where this relation was determined: 15.0 grams of composite eucalyptol-sawdust by 0.8 mm diameter aperture gave 6 months of eucalyptol release, that was considered very positive, understanding high volatility of eucalyptol and a small quantity of composite for further products. The new product is characterized by a carbon footprint (considering the industry frontiers) of 5.94 kg CO2eq/m2 of plywood floor.

Marine lipids are recognized for their health promoting features, mainly for being the primary sources of omega-3 fatty acids, and therefore critical for human nutrition in an age when the global supply for these nutrients is experiencing an unprecedent pressure due to an ever-increasing demand. The seafood industry originates a considerable yield of co-products worldwide that, while already explored for other purposes, remain mostly undervalued as sustainable sources of healthy lipids, often being explored for low value oil production. These co-products are especially appealing as lipid sources since, besides the well-known nutritional upside of marine animal fat, particularly rich in omega-3 polyunsaturated fatty acids (PUFAs), they have also interesting bioactive properties, which may garner them further interest, not only as food, but also for other high-end applications. Besides the added value that these co-products may represent as valuable lipid sources, there is also the obvious ecological upside of reducing seafood industry waste. In this sense, repurposing these bioresources will contribute to a more sustainable use of marine animal food, reducing the strain on already heavily depleted seafood stocks. Therefore, untapping the potential of marine animal co-products as valuable lipid sources aligns with both health and environmental goals by guaranteeing additional sources of healthy lipids and promoting more eco-conscious practices.

Vaccine refusal and hesitancy pose a critical challenge to public health, leading to delays in vaccination and compromising herd immunity. To address this issue, we conducted a comprehensive observational study on the adult Spanish population in 2021. Through an online questionnaire, we explored the sociodemographic and sociocultural factors, beliefs, and opinions of those refusing or holding hesitancy about vaccines, and their vaccination behaviours by vaccine type and sex. Our findings revealed that vaccine refusal rates were relatively low (16.8%), and mainly associated with influenza vaccination (10.3%). Greater refusal of vaccination was observed in over 60 years old, in those expressing hesitancy due to vaccine components and opposing free and compulsory vaccination, unaware that vaccination protects the community and being against consuming cow’s milk and the use of infant formulas for breastfeeding. Vaccine hesitancy was greatest in individuals under 31 years old, women, parents of children under 15 years old, against compulsory vaccination, unaware that vaccination protects the community, with hesitancy due to vaccine costs, and in favour of alternative and complementary treatments. These insights underscore the need for strategies to improve education about vaccination and dispel misconceptions are crucial for effectively reducing vaccine refusal and hesitancy across the population.

In recent years, climate events such as Drought, El Niño, and La Niña have become increasingly frequent and more intense. Oceanographic monitoring was used to collect hydrological data in the middle and lower sectors of the Caeté estuary in different years. Negative rainfall anomalies of up to 45% were recorded during periods marked by Drought and El Niño events, which make the water of the Caeté estuary more saline and alkaline. During these events, the retention of dissolved inorganic nutrients in the middle sector appear to support increased eutrophication and more productive waters, whereas moderate eutrophication and lower productivity were observed in the lower sector. During the La Niña events, by contrast, positive rainfall anomalies may reach 60%, resulting in more oxygenated water in the estuary. In addition, the lower sector tends to more eutrophic during periods of high rainfall and freshwater discharge, as observed in this study during a La Niña event. The paucity of data on the effects of extreme climate events in Amazonian environments means that the findings of the present study may provide a useful model for the assessment of the effects of these events on other natural environments in the Amazon region.

Oral mucositis is most frequently a toxic effect of chemotherapeutic and/or radiotherapeutic treatment, resulting from complex multifaceted biological events involving DNA damage. The clinical manifestations have a negative impact on the life quality of cancer patients. Preventive measures and curative treatment of mucositis are still not well established. The glycine has anti-inflammatory, immunomodulatory and cytoprotective actions, being a potential therapeutic in mucositis. The objective was to evaluate the effects of glycine on the expression of collagen and growth factors, platelet and epidermal in oral mucositis. The mucositis of which was induced by the protocol of Sonis. 40 hamsters were used, divided into two groups: Group I- control; Group II- supplemented with 5% intraperitoneal glycine, 2,0 mg/g diluted in hepes. Histopathological sections were used to perform the immune-histochemical method, the evaluation collagen expression and the growth factors: EGF and PDGF. It was observed that the group supplemented with glycine higher amounts of collagen expression and predominance type of collagen I. The glycine group presented lower immunoexpression of the growth factors, EGF and PDGF. The group supplemented with glycine showed a marked healing process of the oral mucosite, demonstrated by the predominance of collagen type I and reduction of growth factors, EGF and PDGF.

Reactive transport (RT) couples bio-geo-chemical reactions and transport. RT is important to understand numerous scientific questions and solve some engineering problems. RT is highly multidisciplinary, which hinders the development of a body of knowledge shared by RT modelers and developers. The goal of this paper is to review the basic conceptual issues shared by all RT problems, so as to facilitate advance along the current frontier: biochemical reactions. To this end, we review the basic equations to point that chemical systems are controlled by the set of equilibrium reactions, which are easy to model, but whose rate is controlled by mixing. Since mixing is not properly represented by the standard advection-dispersion equation (ADE), we conclude that this equation is poor for RT. This leads us to review alternative transport formulations, and the methods to solve RT problems using both the ADE and alternative equations. Since equilibrium is easy, difficulties arise for kinetic reactions, which is especially true for biochemistry, where numerous frontiers are open (how to represent microbial communities, impact of genomics, effect of biofilms on flow and transport, etc.). We conclude with the basic 10 issues that we consider fundamental for any conceptually sound RT effort.

Arbutus unedo L. is a small Ericaceae tree with a circum-Mediterranean distribution. It has a huge ecological impact on southern Europe forests and a great economic importance, as a source of phytochemicals with bioactive properties and for fruit production. On the foreseen climate change context, breeding towards drought tolerance is necessary in order to ameliorate plant performance. The aim of this work was therefore to study the reproduction mechanisms of strawberry tree, obtain new genetic combinations by hybridization and select genotypes more tolerant to drought stress. A morphological analysis of flowers and pollen was carried out, and controlled pollinations performed both in vitro and ex vitro. The very first approach on strawberry tree breeding by means of hybridization is also presented. Several physiological parameters were evaluated on 26 genotypes submitted to a water deficit regime. Plant behavior under drought greatly varied among genotypes, which showed a high phenotype plasticity. Three genotypes that were able to cope with water restriction without compromising net CO2 assimilation were identified as highly tolerant to drought stress. The results obtained elucidate the reproduction mechanisms of strawberry tree and open the way for a long-term breeding program based on the selection of drought tolerant plants.

Elastic properties of materials and their changes with temperature are important for their applications in engineering. A study on the influence of phase composition of AISI 4130 alloy on Young's modulus (Ed), shear modulus (Gd), and damping (Q-1) was carried out by Impulse Excitation Technique (IET). The material characterization was carried out using confocal microscopy, XRD, MET, HV, and dilatometry. A stable structure, composed of ferrite (BCC) and pearlite (α-Fe+Fe3C), was obtained by annealing. Metastable structure of martensite (BCT) was obtained by quenching. The Ed, Gd, and Q-1 were measured, varying the temperature from RT to 900 °C. The values of Ed and Gd, at RT, were determined as 201.5 and 79.2 GPa (annealed), and 190.13 and 76.5 GPa (quenched), respectively. In the annealed steel, the values Ed and Gd decrease linearly on heating up to 650 °C, with the thermal expansion. In the quenched steel, weak changes in the dilatometric curve, Ed, Gd, and Q-1, in the range of 350-450 °C, indicated decompositions of the martensitic phase. Sharp decrease in the moduli and high peak of Q-1, was observed for both samples around 650-900 °C, revealing low lattice elastic stability of the phases during transformations α(BCC)+Fe3C↔γ(FCC).

Urban gardens have important social, environmental and economic roles in big cities, contributing to their sustainability. However, food production in urban gardens may be compromised due to soil pollution that resulted from decades of industrial non-regulated environmental activity and mobile transport. In this study, 12 soils from the urban agricultural area of Rome (Italy) were analyzed for the metals Be, Ba, Pb, Co, Ni, V, Zn, Hg, Cd, As, Cu, and Cr. All but one of the soils under analysis were characterized by at least one metal concentration above the threshold limit defined by the Italian Legislative Decree 152/2006 (ILD) for agricultural soils. Multivariate analysis showed that the soils could be classified into five clusters: clusters I and II had relatively lower mean metal concentrations; clusters III, IV, and V had relatively higher mean metal concentrations with several metal concentrations above the threshold proposed by ILD. Three factors contributing to the variability of the metal’s concentration in the soils under investigation were identified: geological factor, related with metals As, Ba, Be, and V; anthropogenic factor, related with Pb and Cu; and, a mixed factor related with Co, Cr, Ni, and Zn. High metal content may limit the utilization of urban soils as urban gardens for food production.

The objective of this study was to evaluate the potential benefits of feeding spray-dried porcine plasma (SDPP) to pigs infected with African swine fever virus (ASFV). Two groups of twelve weaned pigs each were fed with CONVENTIONAL or 8% SDPP enriched diets. Two pigs (trojans)/group) were injected intramuscularly with the pandemic ASFV (Georgia 2007/01) and comingled with the rest of the pigs (1:5 trojan:naïve ratio) to simulate a natural route of transmission. Trojans developed ASF and died within the first week after inoculation but contact pigs did not develop ASF, viremia or seroconversion. Therefore, three more trojans per group were introduced to optimize the ASFV transmission (1:2 trojan:naïve ratio). Blood, nasal and rectal swabs were weekly harvested and at end of the study, ASFV-target organs collected. After the second exposure, rectal temperature of conventionally fed contact pigs increased >40.5˚C while fever was delayed in the SDPP contact pigs. Additionally, PCR Ct values in blood, secretions and tissue samples were significantly lower (P<0.05) for CONVENTIONAL compared to SDPP contact pigs. Under these study conditions, contact exposed pigs fed SDPP had delayed ASFV transmission and reduced virus load, likely by enhanced specific T-cell priming after the first ASFV-exposure.

This study continued the analysis of immunization with the receptor binding domain (RBD) associated with the adjuvants Dimethyldioctadecylammonium bromide (DDA) and Saponin (Sap) (RBD+DDA/Sap) or Aluminum hydroxide (AH) and outer membrane vesicles (OMVs) of Neisseria meningitidis (RBD+AH/OMV); from adult to old age and assessed maternal-fetal transference of antibodies. Outbred Swiss mice were immunized with 2 intramuscular (IM) doses with the antigenic preparations RBD+DDA/Sap, RBD+AH/OMV or RBD alone. The humoral immune response was evaluated using ELISA, avidity-ELISA, Immunoblotting and a Omicron-surrogate-neutralization assay (BA.1), while the cellular immune response was analyzed by ELISpot. Our previous work studied the IgG response; here, we verified that IgM levels were higher right after the immunization doses, but, as IgG, it persisted until 368 days after the immunization. The avidity of IgM increased from low to intermediate-to-high after the booster dose. RBD+DDA/Sap presented neutralizing indexes against Omicron at days 47 and 176, while RBD+AH/OMV showed neutralization on days 21, 47 and 176. Cellular response, measured 465 days after immunization, revealed IFN-Y and IL-4 secretion. The offspring of RBD+DDA/Sap had detectable antibodies, which decreased around 45 days after birth, the last point we analyzed. The results suggested that DDA/Sap is a promising adjuvant mixture to enhance humoral and cellular immune response against SARS-CoV-2, improving maternal-fetal transference of antibodies; cross-reactivity with Omicron variant; and the maintenance of antibodies for a long period.

Background: Evidence supports a causal relationship between circadian disturbance and impaired glucose homeostasis. Method: To determine the effect of a nursing educational intervention on improving healthy sleep, a parallel, open-label clinical trial in subjects with Impaired Fasting Glucose (IFG) or Type 2 Diabetes Mellitus (T2DM) and 18 and older was performed. Study variables were sex, age, fasting glucose, glycated hemoglobin A1c (HbA1c), Pittsburgh Sleep Quality Index (PSQI), sleep duration and efficiency, BMI, antidiabetic treatment and diet and physical exercise. An individual informative educational intervention was carried out following a bidirectional feedback method. It was intended to develop skills to improve sleep through 9 simple tips. An analysis of covariance was performed on all the mean centered outcome variables controlling for the respective baseline scores. Results: After the intervention, in the experimental group, PSQI dropped, the duration and quality of sleep increased. Further, a decrease in fasting glucose and in HbA1c levels was observed. Conclusion: The proposed intervention has proven to be effective to improve sleep quality, time, and efficiency and in only 3 months, to achieve a decrease in fasting glucose and HbA1c levels. These findings support the importance of sleep and circadian rhythms education focused on improving in T2DM or IFG.

Atrial fibrillation (AF) is a cardiac arrhythmia caused by electrophysiological anomalies in the atrial tissue, tissue degradation, structural abnormalities, and comorbidities. A direct relation exists between AF and altered mitochondrial activity resulting from membrane potential loss, contractile dysfunction, or decreased ATP levels. This review aimed to elucidate the role of mitochondrial oxidative mechanisms in AF pathophysiology, the impact of mitochondrial oxidative stress on AF initiation and perpetuation, and current therapies. This review followed the Preferred Reporting Items for Systematic Reviews and Meta-Analysis Extension for Scoping Reviews. PubMed, Excerpta Medica Database, and Scopus were explored until June 2023 using "MESH terms." Bibliographic references from relevant papers were also included. Oxidative stress is an imbalance that causes cellular damage from excessive oxidation, resulting in conditions such as AF. An imbalance in reactive oxygen species production and elimination can cause mitochondrial damage, cellular apoptosis, and cardiovascular diseases. Oxidative stress and inflammation are intrinsically linked, and inflammatory pathways are highly correlated with the occurrence of AF. AF is an intricate cardiac condition that requires innovative therapeutic approaches. The involvement of mitochondrial oxidative stress in the pathophysiology of AF introduces novel strategies for clinical treatment.

1) Background: The objective was to evaluate the corrosion resistance of different commercially pure ultrafine-grained (UFG) titanium and its alloys with acid etched surface processed by equal-channel angular pressing (ECAP); 2) Methods: Coarse-grained and UFG titanium samples were investigated using polarization resistance technique. Surface characteristics of the native oxidized layer were evaluated by TEM and XRD. Electrochemical tests were under physiological electrolyte at a rate of 1 and 10 mV/s. Weight loss tests were performed after immersion into HCl solution for up to 3 years; 3) Results: UFG titanium was less susceptible to corrosion which was identified under lower rates and at higher polarization resistance than its coarse grain counterparts. Titanium Grade 2 and Grade 4 demonstrated similar corrosion susceptibility. Titanium Grade 5 revealed a thin and tightly adhered native oxide layer with adequate corrosion resistance; 4) Conclusions: ECAP process imposed a more compact and adhered oxidized layer. Surface etching techniques delivered a thicker native TiO₂ layer, being both grain refinement and surface etching techniques responsible for the improved corrosion resistance of Titanium samples under physiological environment after 3 years of observation.

This study explores the impact of regular physical exercise on the quality of life and body image among Para-athletes, emphasizing the necessity of such activities for physical, social, and psychological health. This qualitative study employs content analysis and ethnomethodology to evaluate seven Para-athletes from the Navy's Paralympic Project, using focus group interviews to assess their perceptions. The findings reveal that participation in structured sports programs positively influences body image and quality of life, leading to improved performance in training, social interactions, and competitive events. The analysis suggests that motivation and self-esteem are fundamental to the sporting success of Paralympic athletes. Both external and internal motivations are crucial for sustaining athletic careers and overcoming challenges. Self-esteem enables athletes to remain confident in their abilities, even after setbacks.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

Sea level rise and increased storm events, urge cities to develop governance capacity. However, a cohesive conceptual and empirical-based understanding of what governance capacity implies, how to measure it, and what cities can learn, is largely lacking. Understanding the influence of context is critical to address this issue. Accordingly, we aim to identify crosscutting contextual factors and their influence in impeding, enhancing or prioritising different elements of governance capacity to address urban flood risk. By assessing governance capacity through nine conditions and 27 indicators in two Dutch and two cities in the UK, three crosscutting contextual factors are identified: 1) flood probability and impact, 2) national imposed institutional setting, and 3) level of authority to secure long-term financial support. We found that contextual factors explain differences in urban capacity-priorities within and between both countries. The institutional setting in the UK and recent political devolution emphasized the role of citizen awareness, stakeholder engagement, entrepreneurial agents, and the overall necessity for local capacity-development. The Dutch focus on flood safety through centralised public coordination reduces flood probability but also inhibits incentives to reduce flood impacts and reduced public awareness. In conclusion, the three identified contextual factors enable a better understanding of capacity-building priorities.

Due to satisfactory mechanical properties, low specific weight and other advantages, a substantial utilization of laminated structural composites in many components and equipments of several industry sectors, especially in the past two decades, has been made. This class of materials has a good potential to be an important ally to support scientists and engineers with the main current world challenge: an energy transition process that must occur with sustainability, eco-friendly materials and based on an efficient reduction of greenhouse gas emissions. In this context, a microanalysis (scale length: 10μm to 1mm) of mechanical behavior that considers the multiphase characteristics, at leastwise a matrix and a reinforcement phase, of this kind of composites must be explored, i. e., a heterogeneous material is assumed to predict, for example, the effective tensors of stiffness or compliance by a homogenization process, modeling to damage analyses, studies about progressive delamination and other specific aspects of a composite can be previously investigated using micromechanical approaches. Therefore, the understanding of fundamental micromechanics as well as some advanced models are essential to apply these materials in structural industry components. In this sense, this systematic literature review is designed to investigate the main basic and advanced models of laminated composites micromechanics and using this overall study, have been developed, in the end, an analysis of research trends to the topic, in which, lines to future researches are indicated.

The world is facing a great technological transformation towards full autonomous vehicles, where optimists predict that by 2030, autonomous vehicles will be sufficiently reliable, affordable and common to displace most human driving. To cope with these trends, reliable perception systems must enable vehicles to hear and see all the surroundings, being light detection and ranging (LiDAR) sensors a key instrument for recreating a 3D visualization of the world in real time. However, perception systems must rely in accurate measurements of the environment. Thus, sensors must be calibrated and benchmarked before being placed on the market or assembled in a car. This article presents an Evaluation and Testing Platform for Automotive LiDAR sensors with the main goal of testing not only commercially available sensors, but also sensor prototypes currently under development in Bosch Automotive Electronics division. The testing system can benchmark any LiDAR sensor under different conditions, recreating the expected driving environment to which such devices are normally subjected. To characterize and validate the sensor under test, the platform evaluates several parameters such as the field of view (FoV), angular resolution, sensor’s range, etc. This project results from a partnership between the University of Minho and Bosch Car Multimedia Portugal, S.A.

Several methods can be used to evaluate antibody avidity, one of which is the modified ELISA, in which a chaotropic agent is added to disrupt the binding between the antigen and the antibody. Although the avidity index provides relevant information about the functionality of antibodies, it does not allow us to characterize which antigens the antibodies are strongly bound to. To this end, we adapted the Immunoblot and Dot-Blot techniques by adding potassium thiocyanate (KSCN) after incubating nitrocellulose membranes with serum from mice immunized with Neisseria meningitidis outer membrane vesicles (OMVs) or serum from mice immunized with recombinant receptor-binding domain (RBD) of SARS-CoV-2, with different adjuvants for each antigen. In terms of results, when standardizing the incubation time of sera with KSCN, we observed that 5 minutes was the ideal time for both assays, however, when using different dilutions of serum from mice immunized with RBD, there was an influence on the strength of antigen-antibody binding. For the N. meningitidis assay, the antibodies maintained high avidity for the antigens present in the OMVs, PorA, NadA, and Opa, especially in the presence of the aluminum hydroxide adjuvant. The research showed that standardizing the Immunoblot and Dot-Blot in the same assay optimizes time and resources, allowing qualitative analysis for two different antigens, and resulting in more robust information for immunization studies against these pathogens.

Large amounts of gas hydrate are present in marine sediments offshore Taitao Peninsula, near the Chile Triple Junction. Here, marine sediments on the forearc contain carbon that is converted to methane in a zone of very high heat flow and intense rock deformation above the downgoing oceanic spreading ridge separating the Nazca and Antarctic plates. This regime enables vigorous fluid migration. Here we present an analysis of the spatial distribution, concentration, estimate of gas phases (gas hydrate and free gas) and geothermal gradients in the accretionary prism and forearc sediments offshore Taitao (45.5° - 47° S). Velocity analysis of Seismic Profile RC2901-751 indicates gas hydrate concentration values <10% of the total rock volume, and extremely high geothermal gradients (<190 °Ckm^-1). Gas hydrates are located in shallow sediments (90-280 meters below the seafloor). The large amount of hydrate and free gas estimated (7.21x10¹¹ m³ and 4.1x10¹⁰ m³, respectively), the high seismicity, the mechanically unstable nature of the sediments, and the anomalous geothermal conditions, set the stage for potential massive releases of methane to the ocean mainly through hydrate dissociation and/or migration directly to the seabed through faults. We conclude that the Chile Triple Junction is an important methane seepage area and should be the focus of novel geological and ecological research.

Electromagnetic induction (EMI) and electrical resistivity tomography (ERT) are geophysical techniques measuring soil electrical conductivity, providing insights into properties correlated with it, to depths of several meters. EMI measures apparent electrical conductivity (ECa, dS m−1) without physical contact, while ERT acquires apparent electrical resistivity (ERa, ohm m) using electrodes. Both involve mathematical inversion to obtain models of spatial distribution for soil electrical conductivity (σ, mS m−1) and electrical resistivity (⍴, ohm m), respectively, where ⍴ is the reciprocal of σ. Soil salinity can be assessed from σ over large areas by a calibration process consisting of a regression between σ and the electrical conductivity of the saturated soil paste extract (ECe, dS m−1), used as a proxy for soil salinity. This research aims to compare the prediction abilities of the faster EMI to the more reliable ERT for estimating σ and predicting soil salinity. The study conducted surveys and sampling at four locations with distinct salinity levels in Portugal, analysing the agreement between the techniques and obtained 2D vertical soil salinity maps. In our case study, the agreement between EMI and ERT models was fairly good in three locations, with σ varying between 50 and 500 mS m−1. However, this was not the case at location 4, where σ exceeded 1000 mS m−1 and EMI significantly underestimated σ, when compared to ERT. As for soil salinity prediction, both techniques generally provided satisfactory and comparable regional-level predictions of ECe, and the observed underestimation in EMI models did not affect significantly the overall estimation of soil salinity. Consequently, EMI demonstrated an acceptable level of accuracy in comparison to ERT in our case studies, supporting the confidence in utilizing this faster and more practical technique for measuring soil salinity over large areas.

Civil construction is one of the oldest known activities in humanity, reports indicate that builders of the Roman Empire already sought the reuse of materials. Currently, considering the depletion of the supply of natural resources, the recycling of solid waste from construction and demolition (CDW), not only provides new products, but also offers ecological and economic alternative. In this context, this research seeks new variables for the disposal of waste from construction and demolition having in the composition of artificial finishing stones an odd possibility to be analyzed. In this research was developed and analyzed a new composite from the construction and demolition waste using as a binder an orthophthalic polyester resin. The residue was sieved and separated by granulometry by the simplex centroid method, the best compacted mixture was determined statically by ANOVA and the Tukey test. The residue was characterized by X-ray fluorescence and the resin by infrared spectroscopy by Fourier transform. Artificial rock plates were produced with 85% residue and 15% resin, by mass, by vibro system, compression and vacuum, later were cut for mechanical, physical and chemical tests. Analysis was performed by scanning electron microscopy of fractured compositions as well as grain sizes. The artificial stone with the best results presented density of 2,256 g/cm3, water absorption of 0.69%, apparent porosity of 1.55%; bending strength of 34.74 MPa and compression of 111.96 MPa; good results in the alterability and thermal tests. In this satisfactory scenario, the use of this waste in the composition of artificial rocks is promising because it directly meets the concept of sustainable development; replacing the concept of end-of-life of the linear economy, by new circular flows of reuse, restoration and renovation, in an integrated process the circular economy; as well as the quality of the final product with properties similar to the artificial rocks already marketed.

There is currently an exponential growth in the electric vehicle market, which will require an increase in the electrical grid capacity to meet the demand of charging. If, on the one hand, the introduction of energy generation from renewable sources can be used to meet that requirement, the intermittent nature of some of these sources poses challenges to the required real time equilibrium between generation and consumption. The impossibility of controlling generation from some of these sources leads to the attempt of controlling and manage the consumption of electricity, according with the levels of generation. In this context, the emergence of smart grids has introduced mechanisms that guarantee a balance between consumption and generation of electricity. One of these mechanisms is the smart charging of electric vehicles. Effective smart charging relies on communication between the supply equipment and the electric vehicle, en-abling the adjustment of the energy transfer according with the generation levels. Thus, there is a necessity for a standardised system that guarantees this communication. In this context, the ISO 15118 standard, allows high level communication mechanisms, much beyond the basic control solutions offered by the IEC 61851-1 specification. In this context, this paper presents the development of a charge emulation system, based on the ISO 15118 communication protocol and discusses its application for demand response purposes.

Anthropogenic disturbances interacting with natural disturbances, ecological and socio-economic factors can provoke forest degradation and modulate ecosystem resilience. In Haiti, protected areas recently created to reduce forest loss, require studies about forest dynamics and land use to assure the development of sustainable management policies. We combine field interview with Landsat satellite images of the Macaya National Park collected between 1985 and 2021 to investigate: 1) how much of the original forest area has been converted into agricultural or logged area since 1985; and 2) how do elevation and slope influence the expansion of human-induced land-use changes. Our results indicate an increase of 11.36% in forest cover and a reduction of 75.34% in agriculture class cover, despite the passage of seven hurricanes in the region. Forest recovery was apparently unrelated to elevation and slope, and likely reflected the implementation of new environmental laws and policies with the creation of the Macaya National Park in 1983. Restoration and protection programs contributed to ensure access to financial resources, technical assistance and new technology, thus promoting a shift into a more resilient forest system. This study brings hope for forest conservation in Haiti by showing that positive results can be achieved through inclusive collaboration.

Traumatic Brain Injury (TBI) remains a leading cause of morbidity and mortality among all ages; despite the advances, understanding pathophysiological responses after TBI is still complex, involving multiple mechanisms. Previous reviews have focused on potential targets; however, the research on potential targets has continuously grown in the last five years, bringing even more alternatives and elucidating previous mechanisms. Knowing the key and updated pathophysiology concepts is vital for adequate management and better outcomes. This article reviews the underlying molecular mechanisms, the latest updates, and future directions for pathophysiology-based TBI management.

Inbreeding depression is expected to be more pronounced in fitness-related traits, such as pig litter size. Recent studies have suggested that the genetic determinism of inbreeding depression may be heterogeneous across the genome. Therefore, the objective of this study is to conduct a genomic scan across the pig autosomal genome to detect the genomic regions that control inbreeding depression for litter size in two varieties of Iberian pigs (Entrepelado and Retinto). The datasets consist of 2,069 (338 sows) and 2,028 (327 sows) records for litter size (Total Number Born and Number Born Alive) for the Entrepelado and Retinto varieties. All sows were genotyped using the Geneseek GGP PorcineHD 70 K. We employed the Unfavorable Haplotype Finder software to extract runs of homozygosity (ROHs) and conducted a mixed model analysis to identify highly significant differences between homozygous and heterozygous sows for each specific ROH. A total of 8 genomic regions located on SSC2, SSC5, SSC7, SSC8, and SSC13, were significantly associated with inbreeding depression, housing some relevant genes such as FSHR, LHCGR, CORIN, AQP6, and CEP120.

The growth of demand for metallic minerals has faced with the need for new techniques and improving technologies for all mine life cycle operations. Nowadays, the exploitation of old tailings and mine wastes facilities could represent a solution to this demand, with economic and environmental advantages. W-Sn Panasqueira Mine has been operating for more than 100 years. Its first processing plant “Rio” was located near Zêrere river being the mineral processing residues deposited on the top hillside on the margin of this river in Cabeço do Pião tailings dam. The lack of maintenance and monitoring of this enormous structure in the last twenty years represents high risks to the environment and population of the surrounding region. The re-mining of the tailings by hydrometallurgical methods was considered, in order to satisfy these two enounced conditions - metals demand and environmental risk, aiming for the sale of the metal to pay the environmental intervention. Field samples campaign allowed collecting data and results from laboratory tests driving to use regression optimization. The re-mining solution was studied, taking into account the technical, economic, social, and environmental aspects.

In the last five years, European research and innovation programmes have prioritised the development of online catalogues and tools (handbooks, models, etc.) to facilitate the implementation and monitoring of Nature Based Solutions (NBS). However, only a few catalogues and toolkits within European programmes are directly related to mainstreaming of NBS for food production (i.e., edible NBS). Therefore, the main aim of this paper is to present existing NBS tools through the eyes of productive urban landscapes. We reviewed 32 projects related to NBS and 50 tools were identified and characterised. Then, the 6 tools already available, and providing indicators, were further analysed in terms of their format and knowledge domains. Our main conclusion demonstrates that there is a lack of tools capable of supporting users for planning and implementing edible NBS, calculating the food potential of the city and/or of individual edible NBS, including the needed resources for implementation and operation (water, nutrients, energy), and assessing their urban design value, environmental and socio-economic impacts. And when they do exist, there is a resistance to share the models and equations behind the tools to allow other projects to reuse or validate them, fact which is contrary to Open Science principles stood up by many research public agencies.

Background: The newly introduced COVID-19 vaccines have reduced disease severity and hospitalizations. However, they do not significantly prevent infection or transmission. In the same context, measuring IgM and IgG antibody levels is important, but it doesn't provide information about the status of the mucosal immune response. This article describes a comprehensive mapping of IgA epitopes of the S protein, its cross-reactivity, and the development of an ELISA-peptide assay. Methods: IgA epitope mapping was conducted using Spot-synthesis and sera from RT-qPCR COVID-19-positive patients. Specific and cross-reacting epitopes were identified, and an evolutionary analysis from the early Wuhan strain to the Omicron variant was performed using bioinformatics tools and a microarray of peptides. The selected epitopes were chemically synthesized and evaluated using ELISA-IgA. Results: 40 IgA epitopes were identified, with 23 in S1 and 17 in the S2 subunit. Among these, at least 23 epitopes showed cross-reactivity with DENV and other organisms and 24 with other associated coronaviruses. Three MAP4 polypeptides were validated by ELISA, demonstrating a sensitivity of 90-99.96% and a specificity of 100%. Among the six IgA-RBD epitopes, only the SC/18 epitope of the Omicron variants (BA.2 and BA.2.12.1) presented a single IgA epitope. Conclusions: This research unveiled the IgA epitome of the S protein and identified many epitopes that exhibit cross-reactivity with DENV and other coronaviruses. The S protein of variants from Wuhan to Omicron retains many conserved IgA epitopes, except for one epitope (#SCov/18). The cross-reactivity with DENV suggests limitations in using the whole S protein or the S1/S2/RBD segment for IgA serological diagnostic tests for COVID-19. The expression of these identified specific epitopes as diagnostic biomarkers could facilitate monitoring mucosal immunity to COVID-19, potentially leading to more accurate diagnoses and alternative mucosal vaccines.

Micro-nano-plastics (MNPs) are an important constituent of atmospheric aerosol. However, there is still no standard procedure for their sampling and size fractionation, which is an obstacle to the aggregation and critical analysis of results obtained by different research groups. This review focuses on the sampling and fractionation methodologies used for MNPs. Moreover, a straightforward optimized methodology for the sampling and fractionation is proposed.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyses the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% of nano-TiO2 and compares it to the transparent base binder, and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier-Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity and exhibited values between the conventional binder and PMB regarding rutting resistance, penetration, and softening point. They showed similar behavior as the PMB, demonstrating signs of polymer-modification. The addition of TiO2 seems to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increases the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, considering fatigue and 10.0% concerning permanent deformation.

L-asparaginase (ASNase) is an aminohydrolase currently used in the pharmaceutical and food industries. Enzyme immobilization is an exciting option for both applications, allowing a more straightforward recovery and increased stability. High surface area and customizable porosity make carbon xerogels (CXs) promising materials for ASNase immobilization. This work describes the influence of contact time, pH, and ASNase concentration on the immobilization yield (IY) and relative recovered activity (RRA) using Central Composite Design methodology. The most promising results were obtained using CX with an average pore size of 4 nm (CX-4), reaching IY and RRA of 100%. At the optimal conditions, the ASNase-CXs biocomposite was characterized and evaluated in terms of kinetic properties and operational, thermal and pH stabilities. The immobilized ASNase onto CX-4 retained 71% of its original activity after six continuous reaction cycles, showed a good thermal stability at 37 °C (RRA of 91% after 90 min) and was able to adapt to both acidic and alkaline environments. Finally, the results indicated a 3.9-fold increase in the immobilized ASNase affinity for the substrate, confirming the potential of CXs as a support for ASNase and as a cost-effective tool for subsequent use in the therapeutic and food sectors.

This paper discusses the tectonics of the St. Peter and St. Paul Archipelago (SPSPA) in the Equato-rial Atlantic Ocean, based on the joint-system geometry which show a North-South shorten-ing/transpressional uplift tectonism, is active leading to exhumation of the sub-oceanic mantle. These islets are the summits of a sigmoidal submarine ridge formed by mantle ultramafic rocks. The ridge is crossed by the principal transform deformation zone of the northern transform fault of the St. Paul Multifault System. The South flank ridge exposes serpentinized mantle perido-tites, while the North flank exposes strongly deformed/fractured ultramylonites, recording duc-tile and brittle deformation at lithospheric conditions. The SPSPA show multiple joint systems cutting mylonitic foliation of the exposed rocks, forming three main families: high-angle paral-lel joints of tectonic origin, serpentinization-related joints with random direction and load-release low-angle parallel joints. The tectonic joints show an average direction of N31°E and N28°W, forming a conjugate system with a N1ºW compression axes, coherent with a trans-pressive stress field. Accordingly, the earthquakes focal mechanism close to the islets also shows N-S compression. The previously reported active uplift with an average rate of 1.5 mm/year and the directions of the joint system here reported agreeing with a present-day active N-S compres-sive field at a high angle with the direction of the transform fault.

Dental-implant-supported reconstructions provide comfort and improvements in prosthetic function, adaptation, and stability over conventional treatment options. The objective of this study was to evaluate the effect of multiple cleaning solutions on dentures and their influence on the deterioration and loss of retention of overdenture attachments in a 12-month clinical-use simulation. In this way, four different brands of retentive caps made of Teflon (OT Equator, Locator®, Kerator®, and Locator R-Tx®) were immersed in five different cleaning solutions (Kukident®, Benfix®, Corega®, and Protefix®), and tap water was used as the control group, in a simulation that lasted 12 months. Data were analyzed using two-way ANOVA and a Tukey HSD. Furthermore, a Levene Test and Shapiro–Wilk tests were performed to assess the validation of the ANOVA assumptions. The statistical analysis was performed using R version 4.2.2 software with the significance level set to p &lt; 0.05. There were significant statistical differences between the different manufacturers on the retention forces of the attachment’s retentive caps. For the cleaning solution groups, different statistical results between Kukident® and Benfix® were observed. There were no significant statistical differences between Corega®, Protefix®, and tap water despite the fact that the retention forces decreased in all of them.

The Douro Demarcated Region (DDR) has peculiar edaphoclimatic characteristics that provide a suitable terroir for premium wine production. As climate change effects continue to emerge, ensuring productivity and quality becomes increasingly important for viticulturists, as those directly determine their profits. Cultural approaches, such as the use of biostimulants, are actively being developed to mitigate abiotic stress. The main objective of this work was to assess the effect of foliar sprays of a seaweed (Ascophyllum nodosum) based extract (ANE) and glycine betaine (GB) on grape berry quality, bioactive compounds, and antioxidant activity. A trial was installed in a commercial vineyard (cv. Touriga Franca) in the Douro Superior (Upper Douro) sub-region of the Douro Demarcated Region. In 2020, a total of three foliar sprayings were performed during the growing season, namely at pea-size, bunch closure, and veraison. There was a positive effect of both biostimulants (ANE and GB) on the physiological and biochemical performance of cv. Touriga Franca exposed to summer stress. In general, the GB 0.2% spraying was the most promising treatment for this grape cultivar, as it increased berry quality, the concentration of bioactive compounds (total phenolics, flavonoids and ortho-diphenols), and the antioxidant activities. These results revealed the efficacy of biostimulants sprayings as sustainable viticultural practice, improving berry quality under summer stress conditions.

Plant-based extracts have been recently employed as sustainable tools to improve biotic and abiotic stress tolerance and increase grape quality. However, knowledge about the effect of these extracts on secondary metabolism compounds, that are fundamental for grape and wine quality, is still scarce. In this study, a trial was installed in an experimental vineyard with the variety Touriga Franca located at University of Trás-os-Montes e Alto Douro, Baixo Corgo sub-region of the Douro Demarcated Region, in two growing seasons: 2019 and 2020. Foliar sprayings with the natural products, nettle extract (NE) and Japanese knotweed extract (JKE), were tested to evaluate their effect on downy mildew incidence and severity, on grapevines bioactive compounds contents and antioxidant activity, at veraison and harvest. NE and JKE have stimulated an improvement in the concentration of total carotenoids in leaves and the concentration of total phenolics in berries along with an improved concentration of total phenolics and flavonoids in leaves and berries. Thus, it was verified that these extracts enhance grapevines bioactive compounds and antioxidant capacity and, consequently, the physiological performance of the plant and the quality of the berries. Considering the challenges posed by climate change in the Mediterranean basin viticulture sector, the use of plant extracts might represent a sustainable tool to mitigate the increasing severity of drought, often associated to heatwaves and high irradiation. Moreover, downy mildew incidence results suggest that an integrated disease management approach combining conventional control with alternative fungicides can be used in the future for a more sustainable viticulture.

Postmenopausal abnormal uterine bleeding is a common clinical problem addressed in gynecological practice and should prompt clinical investigation due to the significant prevalence of malignant and premalignant lesions of endometrium in this age group. Nevertheless, other causes should be considered since its diagnostic and therapeutic management may differ considerably. Here, we present a case of a colouterine fistula due to chronic diverticulitis presenting with postmenopausal abnormal uterine bleeding. This is extremely rare and is caused by the rupture of a diverticular abscess into the uterine wall, resulting in an inflammatory adhesion of the colon and uterus, with necrosis and subsequent fistula formation. The clinical presentation is variable and may include abdominal pain, gastrointestinal tract symptoms, vaginal discharge and abnormal uterine bleeding. The laboratory and imaging techniques may be not completely conclusive and definitive diagnosis can be made intraoperatively. There are different treatment options, being the en bloc resection and primary anastomosis the most used, allowing complete treatment. The prognosis for a colouterine fistula secondary to diverticulitis is excellent after surgery. This case highlights the importance of clinical suspicion of an unusual cause of uterine bleeding and an effective and multidisciplinary approach that allowed complete surgical treatment and patient recovery.

L-asparaginase from bacterial sources have been used in antineoplastic treatments and the food industry. A novel type II L-a sparaginase encoded by the N-truncated gene ansZP21 of halotolerant Bacillus subtilis CH11 isolated from Chilca salterns in Peru was expressed using a heterologous system in Escherichia coli BL21 (DE3)pLysS. The recombinant protein was purified using one-step nickel affinity chromatography and exhibited activity of 234.38 U mg-1 and a maximum catalytic activity at pH 9.0 and 60 °C. The enzyme shows a homotetrameric form with an estimated molecular weight of 155 kDa by gel filtration chromatography. The enzyme half-life at 60 °C was 3 h 48 min, and L-asparaginase retained 50% of initial activity for 24 h at 37 °C. The activity was considerably enhanced by KCl, CaCl2, MgCl2, mercaptoethanol, and DL-dithiothreitol (p-value &lt; 0.01). Moreover, the Vmax and Km were 145.2 µmol mL-1 min-1 and 4.752 mM, respectively. These findings evidence a promising novel type II L-asparaginase for future industrial applications.

Background: Extremametly lean athletes could have difficulty for adaptive eating (intuitively or consciously) during ad libitum refeed. Aims: we verificate if there is a relation between adaptive eating and coping strategies with energy intake in a model of refeed proposed for bodybuilders. Methods: Fourteen male bodybuilders (29.6±3.1yrs; 85.6±6.8kg, ≥6 competitions) completed the 4-week each consisting of a 5 days of energy restriction following 2 days of refeed. Dietary assessment, body composition (ultrasound), Recovery stress questionnaire (REST-Q) and BRUMS (Brunel mood scale) were accessed pre and post; Coping Function Questionnaire (CFQ), Mindful Eating Scale version 2 (MES 2) and the Intuitive Eating Scale-2 (IES-2) was used at 4th week. Results: The refeed day resulted in a daily caloric increment of ~44% compared to the average energy intake on the energy restriction days, culminating in a weekly calorie deficit of ~27% and a drop in body mass of 3.1±1.4% with relation to initial values. The most reduced body fat and preserved or gained lean mass. The energy consumption during refeed maintained an inverse relationship with the perception of satiety (r=-0.9; p<0.01), total scores of IES 2 (r=-0.82; p<0.01), as well as with the confidence in hunger and satiety cues (r=-0.62; p=0.02) and congruence in food-body choice (r=-0.56; p=0.04) dimensions. Coping based in emotions maintained a relationship with the total scores of IES 2 (r=0.54; p<0.05) and an inverse relationship with energy intake during refeed (r=-0.42; p<0.05). Conclusion: Our results suggest that a higher perception of internal hunger and satiety signals and higher scores in intuitive eating may contribute to energy intake adequate, even when high scores of coping based in emotions are present.

Windthrow (i.e., trees broken and uprooted by wind) is a major natural disturbance in the Amazon. Images from medium-resolution optical satellites (mostly Landsat) combined with extensive field data have allowed researchers to assess patterns of tree mortality and monitor forest recovery over decades of subsequent succession in different regions. Although satellites with high spatial-resolution have become available for the Amazon in the last decade, they have not yet been employed for the mapping and quantification of windthrow tree-mortality. Here, we address how increasing the spatial resolution of satellites affects plot-to-landscape estimates of windthrow tree-mortality. We combined forest inventory data with Landsat 8 (30 m pixel), Sentinel 2 (10 m), and WorldView 2 (2 m) imagery over an old-growth forest in the Central Amazon that was disturbed by a single windthrow event in November/2015. Remote sensing estimates of tree mortality were produced with Spectral Mixture Analysis and analyzed together with forest inventory data using Generalized Linear Models. Windthrow tree-mortality measured in 3 transects (30 subplots) crossing the entire disturbance gradient was 26.9 ± 11.1% (mean ± 95% CI). Based on this ground truth, the three satellites produced reliable and statistically similar estimates (from 26.5% to 30.3% windthrow tree-mortality, p&lt;0.001). The mean-associated uncertainties decreased systematically with increasing spatial resolution (i.e., from Landsat 8 to Sentinel 2 and WorldView 2). However, the overall quality of fit of models showed the opposite pattern, which may reflect the influence of crown damage not accounted for in our field study, and fast-growing regeneration of leaf area. Among the satellites studied, Landsat 8 most accurately captured field observations of variations in tree mortality across the disturbance gradient (i.e., lower under- and/or overestimation from undisturbed to extremely damaged forest). Although satellites with high spatial-resolution can refine estimates of windthrow severity by allowing the quantification of individual tree damage and mortality, our results validate the reliability of Landsat imagery for assessing patterns of windthrow tree-mortality in dense and heterogeneous tropical forests. Although high-resolution imagery may improve estimates of tree damage and mortality, these should be validated using field data at compatible scales.

Chromoblastomycosis (CBM) and phaeohyphomycosis (FEO) are infections caused by melanized filamentous fungal agents, primarily found in tropical and subtropical regions. Both infections pose significant challenges for the correct identification of the causative agent due to their morphological similarity, making conventional methods of morphological analysis highly subjective. Therefore, molecular techniques are necessary for the precise determination of these species. In this regard, this study aimed to contribute to a new methodology based on PCR-RFLP for the identification of agents causing CBM and FEO. Sequences from the ITS region were used to identify potential restriction enzyme sites in silico, followed by in vitro validation using the selected restriction enzymes. The obtained results were compared with species identification through morphological analyses and sequencing. The results demonstrated that the PCR-RFLP applied in this study accurately identified two major agents of chromoblastomycosis, Fonsecaea pedrosoi and Fonsecaea monophora, as well as Cladophialophora bantiana and Exophiala dermatitidis, both causative agents of phaeohyphomycosis. In this context, the proposed assay can complement current methods for identifying these species, aiding in diagnosis, and contributing to the proper management of these infections.

This paper details a design optimization on a hardware accelerator for an on-board real-time SAR imaging system using the Backprojection algorithm, focusing on algorithm-specific approximations intended to reduce the overhead introduced by intensive functions such as the square root, sine, and cosine functions. The main novelty of this work is that new approximations were investigated so that the final image retains high quality regardless of the error in the approximation function. This paper revisits existing approximation methods, such as linear interpolation, polynomial approximation using the Vandermonde matrix, and Chebyshev polynomials, and compares their performance on the algorithm. Results demonstrate that it is possible to maintain the image quality with an SSIM above 0.99 with less 93% LUTs for the square root and less 88% LUTs for the sine and cosine functions using polynomial approximation with the Vandermonde matrix when compared to the HLS baseline functions.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

In the last two decades, the application of composite structures in many industrial sectors has been made progressively. For the current major scientific and technological challenge, the energy transition with sustainable and eco-friendly initiatives, the polymer matrix laminated composites have been revealed as an excellent alternative for the renewable energy sector. In this context, the knowledge about mechanical behavior of multiphase materials is required. Then, researches related to macro, mesomechanical and multiscale approaches are very important to improve accuracy of the models to predict effective mechanical properties and to develop a better understanding about complex phenomena such as progressive damage, creep and fatigue. Due to theses needs, this research is a synthesis of fundamentals and advanced topics concerning to global modeling of laminated composite structures, layerwise analyzes and micro-macromechanical models, in which mainly fiber, matrix, interface and damage characteristics are studied and used in the macroscale approach. At the end of this study, some final remarks and a trend analysis are proposed based on literature consulted, in other words, expectations for the future works are made by the authors.

Environmental pollution management combined with food safety represent two of the main important challenges of the last decades. Soil and water contamination. have historically threatened food safety. As ubiquitous pollutants, microplastics (MPs) have attracted increasing attention over the last few years, due to their impact on the socio-ecological system. These particles can affect the balance of terrestrial, aquatic and aerial ecosystems. Their negative impacts are intensified when they adsorb and carry toxic chemicals. They can circulate through organisms and accumulate in the human food chain. Physiological dysfunctions in living beings continue to be reported, both in terrestrial and aquatic ecosystems. The question that remains is on what scale this might be affecting the global production of food. The present article addresses issues related to the food industry, including agriculture, livestock, and fish farming. In doing so it seeks to provide subsidies for the evaluation of the real impact of MP dispersion through the different world environments and the resulting effects on global food production.

Ryegrass is one such cereal that has been underutilized in human nutrition despite its high nutritional and functional value due to the presence of phytochemicals and dietary fibers It is a viable option, especially for countries that do not produce wheat, as it is easily adaptable and overgrows, making it economically viable. This study evaluated the nutritional impact, bioactive compounds, and physicochemical and technological properties of partially substituting maize flour (MF) with sprouted whole ryegrass flour (SR) in developing extrusion-cooked breakfast cereals. A completely randomized design with substitutions ranging from 0 to 20 % of MF with SR was employed as the experimental strategy (P < 0.05). Partial incorporation of SR increased the bioavailability of γ-aminobutyric acid and total soluble phenolic compounds. Using sprouted grains can adversely affect the technological quality of extruded foods, but ryegrass, with its high dietary fiber and low lipid content, mitigates these negative effects. Consequently, breakfast cereals containing 4 and 8 % SR exhibited better physicochemical properties, such as reduced hardness and increased crispness. These results are promising for ryegrass and suggest combining the age-old germination process with extrusion can enhance cereal-based breakfast products' nutritional quality and bioactive compound content.

Antisepsis of the hands of medical personnel is one of the most important steps in the process of patient care, since direct contact can cause the cross-transfer of potentially pathogenic microorganisms at surgical sites.This study aimed to analyze the prevalence of microorganisms on the hands of 131 surgeons in a university hospital before the surgical procedure. Swabs were collected from each clinician's hands before and after handwashing. The samples were placed in a transport medium and immediately delivered to a private Clinical Analysis Laboratory from São Luis-Maranhão. The microorganisms were identified by ionization source mass spectrometry and matrix-assisted laser desorption (MALDI-TOF), and antibiotic susceptibility tests (AST) were performed using the Vitek2 automated system. The results showed a high frequency (100%) of microorganisms before handwashing, but after surgical antisepsis, the rate dropped significantly (p&lt;0.05) to 27.5%. Gram-positive cocci and rods were the most common microbes, followed by gram-negative bacilli species. The effectiveness of hand antisepsis was 72.5%. The ideal would be 100% efficacy, that is, 0% microorganisms in all surgeons. It is logical that the presence of any organism, no matter how infrequent it may be, will always represent a great risk of postoperative infection for any patient.

Mitochondrial introgression raises questions of biogeography, and extent of reproductive isolation and natural selection. Previous phylogenetic work on the Sorex araneus complex revealed apparent mitonuclear discordance in Iberian shrews indicating past hybridization of S. granarius and the Carlit chromosomal race of S. araneus, enabling introgression of the S. araneus mitochondrial genome into S. granarius. To further study this, we genetically typed 61 S. araneus/coronatus/granarius from localities in Portugal, Spain, France and Andorra at mitochondrial, autosomal and sex-linked loci, and combined our data with the previously published sequences. Our data are consistent with the earlier data that S. coronatus and S. granarius are the most closely related of the three species and confirm that S. granarius from the Central System mountain range in Spain captured the mitochondrial genome from a population of S. araneus. The mitochondrial capture event can be explained by invoking a biogeographical scenario whereby S. araneus was in contact with S. granarius during the Younger Dryas in central Iberia despite the two species currently having disjunct distributions. We discuss whether selection favoured S. granarius with an introgressed mitochondrial genome. Our data also suggest recent hybridization and introgression between S. coronatus and S. granarius and between S. araneus and S. coronatus.

The present article describes the synthesis of an isonicotinate-derived meso-arylporphyrin, that has been fully characterized by spectroscopic methods (including fluorescence spectroscopy), as well as by elemental analysis and by HR-MS. The structure of a n-hexane monosolvate has been determined by single crystal X-ray diffraction analysis. The radical scavenging activity of this new porphyrin against the 2,2-diphenyl-1-picrylhydrazyl (DDPH) radical has been measured. Its antifungal activity against three yeast strains (C. albicans ATCC 90028, C. glabrata ATCC 64677 and C. tropicalis ATCC 64677) has been tested, using the disk diffusion and the microdilution methods. Whereas the measured antioxidant activity was low, the porphyrin showed moderate but encouraging antifungal activity. Finally, a study of its effect on the germination of lentil seeds revealed interesting allelopathic properties.

The rapid development of Deep Learning brought novel methodologies for 3D Object Detection using LiDAR sensing technology. These improvements in precision and inference speed performances lead to notable high performance and real-time inference, which is especially important for self-driving purposes. However, the developments carried by these approaches overwhelm the research process in this area since new methods, new technologies, and software versions lead to different project necessities, specifications and requirements. Moreover, the improvements brought by the new methods may be due to improvements in newer versions of deep learning frameworks and not just the novelty and innovation of the model architecture. Thus, it became crucial to create a framework with the same software versions, specifications and requirements that accommodate all these methodologies and allow the easy introduction of new methods and models. A framework is proposed that abstracts the implementation, reusing and building of novel methods and models. The main idea is to facilitate the representation of state-of-the-art (SoA) approaches and simultaneously encourage the implementation of new approaches by reusing, improving and innovating modules in the proposed framework, which has the same software specifications to allow a fair comparison. This makes it possible to determine if the key innovation approach outperforms the current SoA by comparing models in a framework with the same software specifications and requirements.

Cancer is among the leading causes of death worldwide. Therefore, timely diagnosis and appropriate treatment are very important. There are many disadvantages that come with traditional cancer treatments, such as chemotherapy and radiotherapy. In these treatments, the specific drug concentration affects not only the tumor site but also healthy tissues or organs. One of the foremost promising uses of nanotechnology is in the field of medical technology and specific site targeting can be achieved due to manipulation of materials at a nanometric scale. Nanotechnology offers specific benefits in terms of cancer therapy by enhancing it and reducing its adverse effects by guiding drugs to selectively target cancer cells. In addition, the use of minute amounts of medicine can lead to cost savings. Furthermore, nanoparticles can also be used as imaging agents to improve cancer diagnostics, therapeutics, and treatment management. Thus, this review has focused on the different types of nanoparticles used in cancer therapy, their action mechanisms, and their benefits and applications in diagnosis, imaging, and treatment. This review sums up the parameters that need to be considered when designing systems for cancer therapy while considering the desired characteristics of the nanoparticles from the biological point of view.

Climate change will pose a challenge for the winemaking sector worldwide, bringing progressively drier and warmer conditions and increasing the frequency and intensity of weather extremes. The short-term adaptation strategy of applying biostimulants through foliar application serves as a crucial measure in mitigating the detrimental effects of environmental stresses on grapevine yield and berry quality. The aim of this study was to evaluate the effect of foliar application of a seaweed based biostimulant (A. nodosum – ANE) and glycine betaine (GB) on berry quality, bioactive compounds, antioxidant activity, and elucidated their action on the secondary metabolism. A trial was installed in a commercial vineyard (cv. ‘Touriga Franca’) in the Cima Corgo (Upper Corgo) sub-region of the Douro Demarcated Region. A total of four foliar sprayings were performed during the growing season: at flowering, pea size, bunch closer, and veraison. There was a positive effect of GB in the berry quality traits. Both ANE and GB increased the synthesis of anthocyanins and other phenolics in berries and influenced the expression of genes related to the synthesis and transport of anthocyanins (CHS, F3H, UFGT, MATE1 and GST). So, they have the potential to act as elicitors of secondary metabolism, leading to improved grape quality, but also sets the foundation for sustainable agricultural practices in the long run.

Deficiency of Cytochrome P450 Steroid 21-hydroxylase (CYP21A2) represents 90% of cases in congenital adrenal hyperplasia (CAH), an autosomal recessive disease caused by defects in cortisol biosynthesis. Computational prediction along with functional studies are often the only way to classify variants to understand the links to disease-causing effects. Here we investigated the pathogenicity of uncharacterized variants in the CYP21A2 gene reported in the Brazilian and Portuguese populations. Physicochemical alterations, residue conservation, and effect on protein structure were accessed by computational analysis. The enzymatic performance was obtained by functional assay with the wild-type and mutant CYP21A2 proteins expressed in HEK293 cells. Computational analysis showed that p.W202R, p.E352V, and p.R484L have severely impaired the protein structure, while p.P35L, p.L199P, and p.P433L have moderate effects. The p.W202R, p.E352V, p.P433L, and p.R484L variants showed residual 21OH activity consistent with the simple virilizing phenotype. The p.P35L and p.L199P variants showed partial 21OH efficiency associated with the non-classical phenotype. Additionally, p.W202R, p.E352V and p.R484L also modified the protein expression level. We have determined how the selected CYP21A2 gene mutations affect the 21OH activity through structural and activity alteration contributing to the future diagnosis and management of 21OH deficiency.

Treatment with calcitriol, the hormonal form of vitamin D, has shown beneficial effects in ex-perimental models of acute lung injury. In this study we aimed to analyze the associations be-tween calcitriol supplementation and the risk of SARS-CoV2 infection or COVID-19 mortality. Individuals ≥18 years old living in Catalonia and supplemented with calcitriol from April 2019 to February 2020 were compared with propensity score matched controls. Outcome variables were SARS-CoV2 infection, severe COVID-19 and COVID-19 mortality. Associations between calcitriol supplementation and outcome variables were analyzed using multivariable Cox proportional regression. A total of 8076 patients were identified as being on calcitriol treatment. Advanced chronic kidney disease and hypoparathyroidism were the most frequent reasons for calcitriol supplementation in our population. Calcitriol use was associated with reduced risk of SARS-CoV2 infection (HR 0.78 [CI 95% 0.64-0.94], p=0.010), reduced risk of severe COVID-19 and reduced COVID-19 mortality (HR 0.57 (CI 95% 0.41-0.80), p=0.001) in patients with advanced chronic kidney disease. In addition, an inverse association between mean daily calcitriol dose and COVID-19 severity or mortality was observed in treated patients, independently of renal function. Our findings point out that patients with advanced chronic kidney disease could benefit from calcitriol supplementation during the COVID-19 pandemic.

Objective: to create a set of eligibility criteria for the use of MHT in non-gynecological cancer patients. Methods: We searched all articles published in peer-reviewed journals up to March 2021. The PICOS standards were used and the selection criteria as follows: menopausal women of any age with non-gynecological and non-breast cancer receiving HMT, any MHT preparation (oestrogens alone or combined with a progestogen, tibolone or tissue selective oestrogen complex) or any route of administration (oral, transdermal, vaginal or intra-nasal), recurrence and mortality, randomized controlled trials, and related extension studies or follow-up reports. Results: Women colorectal cancer survivors who use MHT have a lower risk of death from any cause than those survivors who do not use MHT. Women Skin Melanoma Survivors Using MHT Have Longer Survival than Non-MHT Survivors. There is no evidence that women lung cancer survivors who use MHT have a different survival rates than those survivors who do not use MHT. Conclusion: MHT is safe in women who have suffered from colorectal, lung or skin melanoma cancers The study was registered at www.prospero.org (CRD42020166658)

Microbial competition within plant tissues affects invading pathogens' fitness. Metabolomics is a great tool for studying their biochemical interactions by identifying accumulated metabolites. Xylella fastidiosa, a Gram-negative bacterium causing Pierce's disease (PD) in grapevines, secretes various virulence factors including cell wall degrading enzymes, adhesion proteins, and quorum sensing molecules. These factors, along with outer membrane vesicles, contribute to its pathogenicity. Previous studies demonstrated that co-inoculating X. fastidiosa with Paraburkholderia phytofirmans strain PsJN suppressed PD symptoms. Here, we further investigated the interaction between the phytopathogen and the endophyte by analyzing the exometabolome of wild-type X. fastidiosa and a diffusible signaling factor (DSF) mutant lacking quorum sensing, cultivated with 20% P. phytofirmans spent media. LC-MS and MAGI were used to detect and map metabolites to genomes revealing a total of 121 metabolites, of which 25 were further investigated. These metabolites potentially relate to host adaptation, virulence, and pathogenicity. Notably, this study presents the first comprehensive profile of X. fastidiosa in the presence of P. phytofirmans spent media. The results highlight that P. phytofirmans and the absence of a functional quorum sensing affect the ratios of glutamine to glutamate (Gln:Glu) in X. fastidiosa. Additionally, two compounds with plant metabolism and growth properties, 2-Aminoisobutyric acid and Gibberellic Acid, were downregulated when X. fastidiosa interacted with P. phytofirmans. These findings suggest that P. phytofirmans-mediated disease suppression involves modulation of the exometabolome of X. fastidiosa, impacting plant immunity.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

The use of recombinant bovine somatotropin (rbST) leads to an increase, in variable amounts, of milk production in buffalo, but there is a lack of information on the influence of rbST on their metabolism. This study looked at the effects of a single 500 mg dose of rbST on lipid profile, liver and kidney function and physical, chemical and cellular constitution of milk in 14 buffalo over 14 days, from the 100th day of lactation, and compared them with 14 animals in a control group. From the 1st day after rbST, there was a rise in beta hydroxybutyrate (β-HBO), possibly due to the higher dry matter intake or by biotransformation of NEFA into β-HBO. Treatment did not influence blood glucose, non-esterified fatty acids (NEFA), triglycerides, cholesterol, total protein, albumin, AST, GGT, bilirubin, urea or creatinine. In 71.3% of the buffalo there was a gradual increase in milk production with maximal response in the first week that was then followed by a gradual decrease, whilst in 21.4%, the increase in production occurred between 7 and 10 days, and only 7.1% of animals did not respond. On the 3rd, 5th, 7th and 10th days after treatment, an increase was found in milk production between the two groups equal to 1.04, 1.52, 1.42 and 1.06 liters, respectively. In relative terms this means an increase in milk production, respectively, of 15.1%; 21.0%; 19.8 % and 15.1 %. The constitution of the milk showed no difference in the amounts of fat, lactose, total solids or somatic cell count; however, on the 3rd day after rbST, there was a decrease in protein; notably, from the 5th day, protein values show no statistical difference. It can be concluded that the application of rbST in buffalo from the 100th day of lactation is metabolically safe, since the treatment neither caused imbalances in fat metabolism nor overloaded the liver or renal function, and the changes in milk composition were transient and limited to a decrease in milk protein.

Suicide is a public health problem influenced by a variety of biological, psychological, social, and environmental factors. Recognizing the warning signs at each stage is crucial for prevention and helping those at risk. In this context, body awareness, especially interoceptive body awareness, emerges as a potentially relevant and underexplored factor. In this study, binary logistic regression and linear regression analyses were used to examine the relationship between interoceptive body awareness and suicidal orientation in Colombian university students. In addition, the bootstrap technique was used to resample and estimate the distribution of the data. The results support the idea that greater interoceptive awareness may protect against suicidal orientation by improving emotional regulation. An inverse relationship was found between interoceptive awareness and suicidal ideation. These findings are consistent with previous literature on the importance of body awareness for emotional well-being. Further longitudinal research is needed to explore this relationship in depth.

Acute lymphoblastic leukaemia is currently treated with bacterial L-Asparaginase; however, its side effects bring up the special need for improved and efficient novel enzymes development. Previously, we obtained low anti-asparaginase antibody production and high serum enzyme half-life in mice with the P40S/S206C mutant; however, its specific activity was significantly reduced. Thus, our aim was to test single mutants, S206C and P40S, for in vitro and in vivo assays. Our results showed that the drop in specific activity was caused by P40S substitution. Besides, our single mutants were highly stable in biological environment simulation, unlike double mutant P40S/S206C. The in vitro cell viability assay demonstrated that mutant enzymes have higher cytotoxic effect than WT on T-cells derived ALL and on some solid cancer cell lines. The in vivo assays were performed in mice to identify toxicological effects, to evoke immunological response and to study the enzymes pharmacokinetics. From these tests, none of the enzymes was toxic; however, S206C evoked lower physiological changes and immune responses. In relation to pharmacokinetic profile, S206C has two-fold higher activity than WT and P40S two hours after injection. In conclusion, we present bioengineered E. coli asparaginases with high specific enzyme activity and lesser side effects.

This paper presents a new information technology platform specially tailored for infrastructure asset management of urban water systems operated by water utilities of lower digital maturity level, developed in the scope of DECIdE research project. This platform aims at the integration of different data from the water utilities with several information systems and the assessment of the system performance, in terms of water losses, energy efficiency and quality of service by using developed tools (i.e., water and energy balances and key performance indicators). This platform was tested with data from five small to medium size Portuguese water utilities with different maturity levels in terms of technological and human resources. Obtained results are very promising since the platform allows to assess the systems performance periodically which constitute an important part of the infrastructure asset management for small and medium-sized water utilities

Integration of battery energy storage in photovoltaic (PV) systems can reduce the electricity costs and provide desirable flexibility and reliability to these systems decreasing renewable energy fluctuations. This paper presents a review of the PV-battery application in Brazil, highlighting the challenges and prospects based on the state-of-art. A PV-battery systems description is presented in this work, as well as the most applied battery technology and its comparison. The paper also describes the set of applications such as voltage and frequency regulation, renewable energy integration, power quality, etc. In the Brazilian scenario, there are applications of PV-battery systems, most of them part of research and development projects (R&amp;D’s), and some real cases are shown, including its goals, applied equipment, operation modes, strategies, and perspectives. Additionally, this work evaluates the Brazilian scenario regarding the energy storage systems implementation challenges, such as regulatory barriers, business models, and opportunities for R&amp;D in the energy market. In conclusion, it is need develop proper regulatory models to expand PV-battery systems and make them visible to the agents in the electricity sector.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.