Many drylands around the world have seen both soil and vegetation degradation around watering points. It can be seen in spaceborne imagery as radial brightness belts that fade with distance from the water areas. The study's primary goal was to characterize spatio-temporal land degradation/rehabilitation in the drylands of the southeast Iberian Peninsula. The brightness index of Tasseled Cap was discovered to be the best spectral transformation for enhancing the contrast between the bright-degraded areas near the points and the darker surrounding areas far from and in-between these areas. To comprehend the spatial structure present in spaceborne imagery of two desert sites and three key time periods, semi-variograms were created (mid-late 2000s, around 2015, and 2020). In order to assess spatio-temporal land-cover patterns, a geostatistical model (kriging) was used to smooth brightness index values extracted from 30 m spatial resolution images. To assess the direction and intensity of changes between study periods, a change detection analysis based on kriging prediction maps was performed. These findings were linked to the socioeconomic situation prior to and following the EU economic crisis. The study discovered that degradation occurred in some areas as a result of the region's agricultural activities being exploited.

The gold deposits of the eastern region of Cuba are genetically related to the lithological formations of the island arc and the ophiolitic complex, which have been studied and exploited since the time of the Spanish colonization in the mid-sixteenth century. These deposits are part of the so-called Aguas Claras-Guajabales mineral field, in the Holguín Province (Cuba) and lie in an extensive elongated strip of approximately 15 km in length. The object of this work is to make an orderly, detailed, and chronological review of the geological and mining work carried out in this region as well as to highlight the degree of study achieved in each of the stages of research. To facilitate this work, an extensive bibliographic review of all available materials was planned and carried out, such as reports, manuals, monographs, and articles. The results obtained from this study highlight that gold mineralization is closely linked to metasomatic processes produced by the circulation of hydrothermal fluids that affected different lithologies of both the volcanic island arc and the ophiolitic complex, it is noteworthy that the highest gold contents are mainly where the lithologies contact each other. This highlights the fact that the presence of alterations such as serpentinization, listvenitization, rodingitization and propylitization have played a primary role in the deposition of gold during mineralization processes. This work could be a very useful guide for future research in this region, as it is an orderly, concrete, and practical compilation of the characteristics of the mineralization and alterations, as well as a precise indication of the spatial position, thicknesses, and contents of the gold horizons.

Industry 4.0 (i4.0) is one of the fields of knowledge that is most extensively researched recently and whose definition is the most controversial, and Latin America (LatAm) is no exception. Identifying the LatAm countries and institutions with the highest degree of innovation and global impact in the i4.0 field. New citation micro-topics were used to identify the thematic domain: 4.224.1040 Industry 4.0. Difference indicators were extracted from Web of Science, Journal Citation Reports and especially Incites. Broadly speaking, the LatAm effort rate in i4.0 is high, as well as its global impact. The main countries are, in decreasing order, Brazil and Mexico. These countries show a high number of industry collaborations, and Brazil boasts many patent citations. Spain is a key partner of Mexico, Colombia, Argentina, Cuba and Ecuador. The most prominent institutions are the Monterrey Institute of Technology (Tecnológico de Monterrey) and the University of Rio Grande do Sul (Universidade Federal do Rio Grande do Sul – UFRGS). The former specializes in engineering and smart manufacturing systems and the latter in ICT (cloud computing, IoT, and big data, among others).

In South Sudan, three case-control studies found a positive association between Nodding Syn-drome (NS) and a Mansonella perstans infection. To investigate whether M. perstans could play the primary and sole causal role in the development of NS, we examined blood films of persons with and without epilepsy in rural villages affected by NS in Mahenge, Tanzania, to identify M. perstans infections. Study participants were also examined for onchocercal nodules and skin lesions and tested for the presence of anti-O. volvulus antibodies (Ov16 ELISA). One hundred and thirteen epilepsy cases and 132 controls were enrolled, with a mean age of 28.3 years (interquartile range 22 – 34 years); 125 (51%) were females. Of the persons with epilepsy, 43 (38.1%) met the probable NS criteria. M. perstans infection was absent in all participants, but Ov16 prevalence and oncho-cerciasis-associated skin manifestations were positively associated with epilepsy, including probable NS. Onchocercal nodules in the mothers of cases were also positively associated with epilepsy. In conclusion, in contrast with O. volvulus, M. perstans is likely not endemic in Mahenge and therefore cannot be a co-factor for NS in the area. Hence, this filaria cannot be the primary and sole causal factor in the development of NS.

Technology has transformed aeroponics, providing numerous advantages over traditional soil-based agriculture. However, there remains a need for comprehensive information on the types of technology employed in aeroponics and their impact on the growing process. This paper presents a literature review of 47 studies published between 2012 and 2023 in peer-reviewed journals and conference proceedings. As a result, it identifies the status and tendencies in the usage of technology in aeroponics as well as the main opportunities and challenges. Furthermore, this paper introduces the Technology Adoption and Integration in Sustainable Agriculture (TAISA) model. TAISA is a model that identifies the degree of technology integration in any sustainable agriculture system to determine how technology affects production and quality. Overall, the systematic review suggests that technology can play a vital role in improving the efficiency and sustainability of aeroponic farming. However, careful consideration must be given to the costs and technical requirements associated with using these technologies. Moreover, the TAISA model reveals that technology has primarily been employed in creating new processes that are not possible to implement without the help of technology. Therefore, we conclude that technology use has taken root in aeroponics and can be promoted to improve sustainable agriculture.

Iberian holm oak meadows are savannah-like ecosystems that result from traditional silvo pastoral practices. However, such traditional uses are declining, driving changes in the typical tree – open grassland structure of these systems. Yet, there are no studies integrating the whole ecosystem — including the arboreal and the herbaceous layer — as drivers of greenhouse gas (GHG: CO2, CH4 and N2O) dynamics. Here we aim at integrating the influence of tree canopies and interactions among plant functional types (PFT: grasses, forbs, and legumes) of the herbaceous layer as GHG exchange drivers. For that purpose, we performed chamber based GHG surveys in plots dominated by representative canopy types of Iberian holm oak meadows, including Quercus species and Pinus pinea stands, the last a common tree plantation replacing traditional stands; and unravelled GHG drivers through a diversity interaction model approach. Our results show that the tree – open grassland structure especially drove CO2 and N2O fluxes, with higher emissions under the canopy than in the open grassland. Emissions under P. pinea canopies being higher than those under Quercus species. In addition, the inclusion of diversity and compositional terms of the herbaceous layer improve the explained variability, legumes enhancing CO2 uptake and N2O emissions. Changes in the tree cover and tree species composition, in combination with changes in the structure and composition of the herbaceous layer, will imply deep changes in the GHG exchange of Iberian holm oak meadows. These results may provide some guidelines to perform better management strategies of this vast but vulnerable ecosystem.

We show broadband sum-frequency generation (SFG) in the Green-Yellow-Orange-Red spectral range using bismuth triborate, BiB3O6 crystal (BIBO) as nonlinear material. We perform a noncollinear phase-matching configuration within BIBO crystal using the remaining light behind the second harmonic generation stage and the infrared idler of an optical parametric amplifier (OPA). The obtained mixing radiation of ultrafast light sources to generate femtosecond pulses across 520.5 to 742.5 nm region is observed. SFG spectrum from single-pass cross-correlation intensity over such visible range is showed. The SFG wavelengths as a function of tunable wavelength idler OPA agrees with the expectations of parametric conversion condition and open the door to practical multi-beam or multi-color sum-frequency generators.

This article is a scoping review analyzing advances in experimental studies on bacterial self-healing of concrete. From Scopus, ScienceDirect, Web of Science and Google Scholar search engine databases, 54 studies were selected for analysis, and an increasing trend of publications since 2015 was found, with India as the country with the largest research presence. Different ma-terials are used as replacement or admixture in concrete, such as fibers, particles and recycled material from construction waste. It was found that the most commonly used bacteria are Bacillus subtilis and Bacillus sphaericus, which can improve the strength of concrete by generating calcite and sealing cracks. In addition, it was found that the presence of materials such as fibers, ashes and construction recyclates can protect bacteria in an alkaline environment. The designs usually in-clude more than two experimental groups and a control. In summary, this study highlights the importance of bacterial self-healing in concrete and provides information on advances in this field of research.

The copper mining industry is increasingly using artificial intelligence methods to improve cop-per production processes. Recent studies reveal the use of algorithms such as Artificial Neural Network, Support Vector Machine, and Random Forest, among others, to develop models for predicting product quality. Other studies compare the predictive models developed with these machine learning algorithms in the mining industry, as a whole. However, not many copper mining studies published compare the results of machine learning techniques for copper recovery prediction. This study makes a detailed comparison between three models for predicting copper recovery by leaching, using four datasets resulting from mining operations in northern Chile. The algorithms used for developing the models were Random Forest, Support Vector Machine, and Artificial Neural Network. To validate these models, four indicators or values of merit were used: accuracy (acc), precision (p), recall (r), and Matthew’s correlation coefficient (mcc). This paper describes dataset preparation and the refinement of the threshold values used for the predictive variable most influential on the class (the copper recovery). Results show both a precision over 98.50% and also the model with the best behavior between the predicted and the real. Finally, the models obtained show the following mean values: acc=94.32, p=88.47, r=99.59, and mcc=2.31. These values are highly competitive as compared with those obtained in similar studies using other approaches in the context.

This paper proposes an improvement to a recent Peak-to-Average-Power-Ratio (PAPR) reduction technique for Orthogonal Frequency Division Multiplexing (OFDM), the GreenOFDM. This technique, which is inspired by SeLected Mapping (SLM), generates several waveform candidates using a given number of Inverse Fast Fourier Transforms (IFFT), and selects the one with the lowest PAPR for the transmission of the OFDM symbol. In GreenOFDM, we show that for (U) IFFTs, it provides better PAPR reduction capabilities than SLM-OFDM as it increases the number of waveform candidates from U (available for SLM-OFDM) to U^2/4. In this work, we propose a simple and clever extension of the GreenOFDM that further increases the number of waveform candidates by a factor 4 (from U^2/4 to U^2), or equivalently reduces by a factor of 2 the number of IFFTs for a same PAPR performance. Compared to SLM-OFDM, the improved GreenOFDM technique reduces the complexity by requiring only the square-root of the number of IFFTs for a same PAPR reduction performance.

The present article proposes a complete framework for Supply Chain Strategy (SCS) analysis that is adapted to the specific characteristics of the agrifood chain, thereby facilitating management of the former. As a specific case of analysis, the horticultural supply chain, originating in Spain and ending with the European consumer, is analyzed, taking as a reference the marketing companies at origin (mainly social economy companies, i.e.; cooperatives). In addition, a survey of marketing companies is conducted to possibly determine which explicit cooperative growth strategies may include horizontal and vertical collaboration relationships with other members of the chain. The aim is to analyze with whom the cooperative collaborates within the supply chain and the key points of such collaboration. A model analyzing the influence of collaboration on company performance is also considered. The results reveal that, in recent years, aspects related to quality and health have been surpassed and replaced by the concept of sustainability within a framework of collaboration with customers. In any case, it becomes evident that there is a need to expand collaboration within the chain by incorporating the supplier of the supplier, with the aim of making the chain more profitable.

We are experiencing an unprecedented urbanization process that alongside with physical, social and economic developments is having a significant impact on population’s health. Due to higher apprehensions of pollution, violence and poverty, our modern cities no longer ensure a good quality of life so they become unhealthy environments. This study aims to measure the socio-environmental and hematologic profile of residents of Santo André’s landfill – “Bairro Espírito Santo” by using the contextualization of the studied area. The research method is Observational type and from Retrospective cohort and by convenience sampling in Santo André in the Greater ABC region. The study determined a socio environmental profile and the hematologic diseases screening related to a close location to the landfill. The disease manifests itself within a broad spectrum of symptoms that causes changes in blood count parameters. The full blood counts analysis was performed, indicating that the blood counts of residents living near the landfill led to positive hematological changes and diseases like Leukopenia, Anemia, Neutropenia and lymphocytosis were the most common changes. However it is considered that the proof of the relation of cause- effect to environmental exposures that may trigger chronic manifestations in humans requires specific studies that are often complicated.

Background: To investigate the experiences and perspectives of rural physical therapists in relation to various telehealth strategies in physical therapy; Methods: A qualitative field study was conducted in [n=4,344] remote regions of [n=6] (Mexico). Using telehealth technology, 16 physical therapists from 6 clinics expanded their reach and provided physical therapy care to patients located in nonmetropolitan sites. The outcomes measured were the sociodemographic characteristics, telemedicine modalities employed, and the types of treatments administered. These assessments were conducted pre, post-intervention, and during the follow-up period; Results: This study included 4,344 participants, averaging 44.5 ±20.7 years old. Most visits (80.1%) were initial, while 19.9% were follow-ups, with an average of 12.4 ±4.7 sessions. "Puebla sur" had the highest case frequency (29.3%), followed by "Tlalnepantla" (27.5%), "CAPU" (17.4%), "Tlalpan" (15.5%), and "Guadalajara" and "Guatemala" clinics with lower frequencies (8.8% and 1.5%, respectively); Conclusions: This study highlights the potential of telemedicine to surmount barriers such as limited access to healthcare facilities, physical impediments faced by patients in rural areas, and financial burdens on families. The findings contribute to the optimization of telehealth strategies, specifically tailored to the unique challenges of rehabilitation care in underserved rural communities.

The regioselectivity in non-polar [3+2] cycloaddition (32CA) reactions has been studied within the Molecular Electron Density Theory (MEDT) at the B3LYP/6-311G(d,p) level. To this end, the 32CA reactions of nine simplest three-atom-components (TACs) with 2-methylpropane were selected. The electronic structure of the reagents has been characterised through the Electron Localisation Function (ELF) and the Conceptual DFT. The energy profiles of the two regioisomeric reaction paths and ELF of the transition state structures are studied to understand the origin of the regioselectivity in these 32CA reactions. This MEDT study permits to conclude that the least electronegative ends X1 atom of these TACs controls the asynchronicity in the C-X (X = C,N,O) single bond formation, and consequently, the regioselectivity. This behaviour is a consequence of the fact that the creation of the non-bonding electron density required for the formation of the new CX single bonds has a lesser energetic cost at the least electronegative X1 atom than that at the Z3 one.

This study presents a new kinetic scheme for the mass yield prediction of waste lignocellulosic biomasses treated by Hydrothermal Carbonization (HTC). The proposed reactions are based on the decomposition, solubilization, and polymerization of each main fraction of the biomass: cellulose, hemicellulose, and lignin. The ash content was assumed to be inert. The kinetic parameters have been obtained by non-linear adjustment using a data set with 220 experimental runs collected from the literature. The results indicate that the pre-exponential factors range was from 7.33 x10¹ to 1.412x10⁵ min^-1, and activation energies were between 33.75 y 225.3 kJ/mol. A good fit is achieved between the observed and predicted data with an R² of 0.81 and an RMSE of 7.7 %. The proposed scheme was validated with the experimental data obtained by the HTC of sawdust (Pinus radiata) and rapeseed (Brassica napus). The experiments were carried out at temperatures of 190, 220, and 250 ºC and reaction times of 0, 30, 60, 90, and 120 min. The predicted values showed an average error of 2.3 and 3.5 %, respectively. Therefore, the kinetic scheme is a useful tool in the conversion analysis of waste biomass treated by HTC.

Molecules sourced from marine environments hold immense promise for the development of novel therapeutic drugs, owing to their distinctive chemical compositions and valuable medicinal attributes. Notably, Talarolide A and Talaropeptides A-D have gained recent attention as potential candidates for pharmaceutical applications. This study aims to explore the chemical reactivity of Talarolide A and Talaropeptides A-D through the application of molecular modeling and computational chemistry techniques, specifically employing Conceptual Density Functional Theory (CDFT). By investigating their chemical behaviors, the study seeks to contribute to the understanding of the potential pharmacological uses of these marine-derived compounds. The investigation involves the utilization of molecular modeling and computational chemistry tools, with a specific focus on Conceptual DFT. These techniques are applied to examine the chemical reactivity of Talarolide A and Talaropeptides A-D, shedding light on their potential for interacting with various biological targets. The research reveals insights into the chemical reactivity of Talarolide A and Talaropeptides A-D, uncovering active reaction sites and potential biological targets. Talarolide A demonstrates robust anti-inflammatory properties and antitumor activity against diverse cancer cell lines, while Talaropeptide A displays antimicrobial efficacy against both bacteria and fungi. The study underscores the significance of comprehending the chemical reactivity of natural marine products for advancing pharmaceutical development. By employing computational tools such as Conceptual DFT, this research uncovers crucial information about the active sites and potential targets of Talarolide A and Talaropeptides A-D. The findings contribute to the broader understanding of marine-derived peptides and their prospects as pharmaceutical agents, though further investigations are necessary to fully elucidate their pharmacological attributes.

In the coming years, digital applications and services that continue to use the country's native cloud systems will be huge. By 2023, that will exceed 500 million, according to IDC. This corresponds to the sum of all applications developed in the last 40 years. If you are the one you answered, yes! This article is for you!

Aberrant expression of the tight junction protein claudin 6 (CLDN6) is a hallmark of gastric can-cer progression. Its expression is regulated by the transcription factor CREB. But in H. pylo-ri-induced gastric cancer there is no information regarding what transcription factors in-duce/upregulate the expression of CLDN6. We aimed to identify if CREB and YY1 regulate the expression of CLDN6 and the site where they bind to the promoter sequence. Bioinformatics analysis, H. pylori LPS, YY1 and CREB silencing, western blot, luciferase assays, and chromatin immunoprecipitation experiments were performed using the gastric adenocarcinoma cell line AGS. A gen reporter assay suggested that the initial 2000 bp contains the regulatory sequence as-sociated with CLDN6 transcription; the luciferase assay demonstrated three different regions with transcriptional activity, but the -901 to -1421 bp region displayed the maximal transcrip-tional activity in response to LPS. Fragment 1279-1421 showed CREB and surprisingly YY1 oc-cupancy. Sequential ChIP experiments confirmed that YY1 and CREB interact in the 1279-1421 region. Our results suggest that CLDN6 expression is regulated by the binding of YY1 and CREB in the 901-1421 enhancer in which a non-described interaction of YY1 with CREB was established in the 1279-1421 region.

The Church of the Pious Schools of Valencia (18th century) has the largest Valencian dome constructed, with its 24.5 meter span, and it is included among the prestigious great European domes, inspired by the Pantheon and belonging to Neoclassicism. Currently, it is undergoing a thorough study and restoration process to improve the management of the monument, especially to halt its deterioration due to moisture and cracks. An initial study included in the Master Plan (1995) determined that the cracks were caused by thermal effects, but recently other studies have addressed that the failure originated from the walls. Additionally, environmental impact and thermal behavior are among the causes, as excessive humidity due to high interior occupancy can cause damage to the dome, which has historic coatings. As a result of the study process, it is proposed to sensorize the dome of the church to have comprehensive control of temperature, humidity, and CO2, as well as accelerometers to monitor the movements of the structure. With this, after the restoration of the dome, the potential effects of temperature, humidity, and CO2 on the dome's surfaces will be controlled, in addition to verifying if there is any correlation between the cracks and the temperature.

The present work sets out the evaluation of composite laminates through optimization objective functions. Genetic Algorithms (GA), as well as Simulated Annealing (SA), were performed in order to determine the optimal ply orientations of a fiber-reinforced polymer laminate for three given load cases: 1) in-plane loads, 2) combined moments, and 3) in-plane loads and combined moments. It searches the optimal orientation layup, which fulfills at the same time both the maximum strain criterion and the Tsai-Wu failure criterion. Construction of an objective function based on the strains and the stresses involves a minimization process to deformations and a maximization of the safety factor. For the first load case, the initial solution is [±45/0/90/±45]s, and the best solution is [(45/135)2/452]s. For the second load case, [-45/45/45/-45/0/90]s is the initial layup sequence, then the best solution obtained is [(45/-45)2/452]s, where plies at 0° and 90º are not necessary even when axial loads are applied. For the third study case, the original layup sequence is [0/45/-45/45/0/90]s; meanwhile, the best solution calculated is [21/24/145/140/45/49]s. An interesting observation is that each pair of layers has a 5º gap. The simulations show that the qualitative results from the GA are better than the SA, but with a significantly higher computational cost. These kinds of computational tools are expected to be used as a reference guide for an optimal fiber configuration with respect to the common orientations used when composite laminates are designed for a structural application.

: Mistrust, amplified by numerous artificial intelligence (AI) related incidents, has caused the energy and industrial sectors to be amongst the slowest adopter of AI methods. Central to this issue is the black-box problem of AI, which impedes investments and fast becoming a legal hazard for users. Explainable AI (XAI) is a recent paradigm to tackle this challenge. Being the backbone of the industry, the prognostic and health management (PHM) domain has recently been introduced to XAI. However, many deficiencies, particularly lack of explanation assessment methods and uncertainty quantification, plague this young field. In this paper, we elaborate a framework on explainable anomaly detection and failure prognostic employing a Bayesian deep learning model to generate local and global explanations from the PHM tasks. An uncertainty measure of the Bayesian model is utilized as marker for anomalies expanding the prognostic explanation scope to include model’s confidence. Also, the global explanation is used to improve prognostic performance, an aspect neglected from the handful of PHM-XAI publications. The quality of the explanation is finally examined employing local accuracy and consistency properties. The method is tested on real-world gas turbine anomalies and synthetic turbofan data failure prediction. Seven out of eight of the tested anomalies were successfully identified. Additionally, the prognostic outcome showed 19% improvement in statistical terms and achieved the highest prognostic score amongst best published results on the topic.

In this study, ignition delay and burning rate are experimentally investigated in relation to the effect of pristine carbon nanotubes (CNTs), sodium dodecylbenzene sulfonate (SDBS), and diesel blends. Single droplet combustion tests were conducted in a combustion system for 21 days using CNTs at concentrations of 50 ppm and 100 ppm, that were dispersed in Colombian commercial diesel and stabilized by SDBS. Additionally, recordings of the combustion were collected, and the Shadowgraph optical method was utilized for monitoring the evolution of droplet size during combustion. The measurements were done over a four-week period. The results demonstrated that the temporal stability has a direct impact on the single droplet combustion tests because a concentration of CNTs of 100 ppm showed higher stability than those achieved by 50 ppm. Consequently, improvements were found with a concentration of 100 ppm, for instance, thermal conductivity increased by about 20%, ignition delay time by 16.2%, and burning rate by 30.5%.

The current study aimed to examine the relationship between demographic variables within the family context and parenting behaviors among adolescent mothers (including affection, responsiveness, encouragement, and teaching). These factors were correlated with communication, problem-solving abilities, and personal-social development in typically developing infants. The study included a sample of 79 Chilean adolescent mother-child dyads with children aged 10 to 24 months. Communication, problem-solving, and personal-social development were assessed using the Ages and Stages Questionnaire-3, along with a demographic information questionnaire. Parenting behaviors (affection, responsiveness, encouragement, and teaching) were observed using the Spanish version of Parenting Interactions with Children: Checklist of Observations Linked to Outcomes. The findings indicated that employed mothers and those who had not dropped out of school had children with better problem-solving skills. Additionally, children residing with their fathers and female children exhibited superior performance in communication, problem-solving, and personal-social development. Maternal responsiveness was associated with communication and problem-solving, while maternal encouragement was linked to improved problem-solving skills. Maternal teaching was connected to communication, problem-solving, and personal-social development. The study emphasized the significance of parenting and sociodemographic factors among adolescent mothers in influencing their children's development.

Antisepsis of the hands of medical personnel is one of the most important steps in the process of patient care, since direct contact can cause the cross-transfer of potentially pathogenic microorganisms at surgical sites.This study aimed to analyze the prevalence of microorganisms on the hands of 131 surgeons in a university hospital before the surgical procedure. Swabs were collected from each clinician's hands before and after handwashing. The samples were placed in a transport medium and immediately delivered to a private Clinical Analysis Laboratory from São Luis-Maranhão. The microorganisms were identified by ionization source mass spectrometry and matrix-assisted laser desorption (MALDI-TOF), and antibiotic susceptibility tests (AST) were performed using the Vitek2 automated system. The results showed a high frequency (100%) of microorganisms before handwashing, but after surgical antisepsis, the rate dropped significantly (p<0.05) to 27.5%. Gram-positive cocci and rods were the most common microbes, followed by gram-negative bacilli species. The effectiveness of hand antisepsis was 72.5%. The ideal would be 100% efficacy, that is, 0% microorganisms in all surgeons. It is logical that the presence of any organism, no matter how infrequent it may be, will always represent a great risk of postoperative infection for any patient.

In an era characterized by rapid technological advancements, economic fluctuations, and global competition, adaptability and resilience have become critical success factors for businesses navigating uncertainty and complexity. This article explores the role of enterprise agility in today’s business landscape at Latam branch of Tata Consultancy Services (TCS), where organizations face complex and diverse operations. We aim to examine how companies can become more agile in the face of emerging challenges and seize opportunities swiftly to drive growth and deliver value. Since 2014, the division has embarked on an agile transformation journey to drive growth, deliver value, foster innovation, and build resilience in an increasingly dynamic environment. We scrutinize an approach to measuring and enhancing enterprise agility, employing statistical analysis and continuous improvement methodologies to tackle real-world challenges while offering valuable insights and recommendations for organizations aiming to implement similar systems. The results of an agile transformation in a certain company’s Latam branch serve as a compelling case study, demonstrating how the implementation of targeted measures and continuous improvement can significantly bolster enterprise agility. Methodologically, our work applies a novel sequence of parametric statistical tests which, to the best of our knowledge, have not been used in the industry to validate the results of business agility metrics. In future work, we aim to create a new workflow considering non-parametric tests to address data with other statistical distributions. We conclude our work by proposing a sequence of steps for organizations to implement business agility metrics.

We study the effect of oblique illumination on the functioning of a plasmonic nanoantenna for chiral light. The antenna is designed to receive a structured beam of light and produce a nanosized near-field distribution that possesses non-zero orbital angular momentum. The design consists of metal (gold) micro-rods laid on a dielectric surface and is compatible with well-developed nanofabrication techniques. Experimental arrangements often require such an antenna to operate in a tilted geometry, where input light is incident on the antenna at an oblique angle. We analyze the limitations that the angled illumination imposes and discuss approaches to mitigate these limitations. Through our numerical simulations, we find that tilt angles larger than 30 degrees require modifications to the antenna design. Our analysis guides current and future experimental configurations to pushing the limits of resolution and sensitivity.

Stellatolides are natural compounds that have shown promising biological activities, including antitumor, antimicrobial, and anti-inflammatory properties, making them potential candidates for drug development. Chemical Reactivity Theory (CRT) is a branch of chemistry that explains and predicts the behavior of chemical reactions based on the electronic structure of molecules. Conceptual Density Functional Theory (CDFT) and Computational Peptidology (CP) are computational approaches used to study the behavior of atoms, molecules, and peptides. In this study, we present the results of our investigation of the chemical reactivity and ADMET properties of Stellatolides A-H using a novel computational approach called Conceptual DFT-based Computational Peptidology (CDFT-CP). Our study uses CDFT and CP to predict the reactivity and stability of molecules and to understand the behavior of peptides at the molecular level. We also predict the ADMET properties of the Stellatolides A-H to provide insight into their effectiveness, potential side effects, and optimal dosage and route of administration. This study sheds light on the potential of Stellatolides A-H as promising candidates for drug development and highlights the potential of CDFT-CP for the study of other natural compounds and peptides.

The presence of heavy metals in cocoa crops is currently a serious problem for farmers and producers in various regions of Peru. Exports of cocoa and its derivatives to European markets are threatened by possible indications of contamination of heavy metals such as Cadmium (Cd) in cocoa beans for export, some at levels higher than those allowed by food regulations established by European Community, which are oriented to consumer protection. The possible sources of cadmium contamination in cocoa crops can be due to natural activities, such as volcanic activities, erosion processes and sedimentation in rocks that contain minerals with a high content of heavy metals (Greenockite, Burnsite, Hawleite, among others), and by anthropogenic activities such as: mining of associated deposits, agriculture (use of fertilizers), smelting of minerals and burning of fossil fuels. Currently, there is no information about contents of heavy metals in areas located in The Campo Verde-Honoria-Tournavista corridor (Ucayali Region and Huanuco Region), due to this, in this work we make a study of this region. A methodology will be used to take cocoa samples from the seed and soil in these areas, and then through chemical analysis, determine the concentrations of heavy metals, using an atomic absorption spectrophotometer. As a consequence of this study, we determined and concluded that the concentrations of cadmium obtained in soils are slightly higher than European standards allowed. Therefore, with this information we prepare a geochemical cadmium map in soils for the study area, which will help cocoa producers to identify areas that exceed the allowed cadmium values, in order to comply with standards that European Community demands in relation of concentration levels of heavy metals (Cadmium) in chocolate. In this way, we can carry out in the future a mitigation plan for areas with cadmium problems, which allows to reduce their content in order to export the product without any problem. .

Despite of over 20 years of community directed treatment with ivermectin (CDTI), a high prevalence of onchocerciasis and onchocerciasis-associated epilepsy were observed in rural villages in Mahenge, Tanzania. Therefore, we assessed the knowledge, attitude and practice about onchocerciasis in four rural villages in the Mahenge area. This was a qualitative study conducted between June and July 2019. Eleven focus group discussions were organized with persons with epilepsy and their caretakers, community resource persons, and community drug distributors (CDDs), and two in-depth interviews with district programme coordinators of neglected tropical diseases (NTD). Most participants were aware about symptoms of onchocerciasis using local terminologies such as “ukurutu/rough dry skin” and “kuwashwa/itching”. A small proportion of people did not take ivermectin during CDTI for fear of adverse reactions such as itching and swelling. Some men believed that ivermectin may decrease libido. Challenges for high CDTI coverage included, long walking distance by CDDs to deliver drugs to households, persons being away for farming, low awareness of the disease and limited supervision by the NTD coordinators. In conclusion, ivermectin uptake in Mahenge should be optimised by continuous advocacy about the importance of taking ivermectin to prevent onchocerciasis-associated morbidity and by improving supervision during CDTI.

Language learners often face communication problems when they need to express themselves and do not have this ability. On the other hand, continuous advances in technology create new opportunities to improve second language (L2) acquisition through context-aware ubiquitous learning (CAUL) technology. Since vocabulary is the foundation of all language acquisition, this article presents the ULearnEnglish, an open-source system to allow ubiquitous English learning focused on incidental vocabulary acquisition. To evaluate the proposal, 15 learners used the system developed, and 10 answered a survey based on the Technology Acceptance Model (TAM). Results indicate a favorable response to the use of the learner context to assist them in their learning. The ULearnEnglish achieved an acceptance of 78.66% for the perception of the utility, 96% for the perception of ease of use, 86% for user context assessment, and 88% for ubiquity. This study presented a positive response in using the location of users to assist their learning. Among the main contributions, this study demonstrates an opportunity for ubiquity use in future research in language learning. Also, furthers studies can use the source available to evolve the model and system.

Introduction: Within primary ARDS, SARS-CoV-2-associated ARDS (C-ARDS) emerged in late 2019, reaching its peak during the subsequent two years. Recent efforts in ARDS research have concentrated on phenotyping this heterogeneous syndrome to enhance comprehension of its pathophysiology. Methods and Results: A retrospective study was conducted on C-ARDS patients from April 2020 to February 2021, encompassing 110 participants with a mean age of 63.2±11.92 (26-83 years). Of these, 61.2% (68) were male, and 25% (17) experienced severe ARDS, resulting in a mortality rate of 47.3% (52). Ventilation settings, arterial blood gases, and chest X-ray (CXR) were evaluated on the first day of invasive mechanical ventilation and between days two and three. CXR images were scrutinized using a convolutional neural network (CNN). A binary logistic regression model for predicting C-ARDS mortality was developed based on the most influential variables: age, PaO2/FiO2 ratio (P/F) on days one and three, CNN-extracted CXR features, and age. Initial performance assessment on test data (23 patients out of the 110) revealed an area under the receiver operating characteristic (ROC) curve of 0.862 CI (0.654-0.969). Conclusion: Integrating data available in all intensive care units enables the prediction of C-ARDS mortality by utilizing evolving P/F ratios and CXR. This approach can assist in tailoring treatment plans and initiating early discussions to escalate care and extracorporeal life support. Machine learning algorithms for imaging classification can uncover otherwise inaccessible patterns, potentially evolving into another form of ARDS phenotyping. The combined features of these algorithms and clinical variables demonstrate superior performance compared to either element alone.

Renewable Energy Communities (RECs) are emerging as an effective concept and model to empower the active participation of citizens on the energy transition, not only as energy consumers, but also as promoters of environmentally friendly energy generation solutions. This paper aims to contribute to the management and optimization of individual and community Distributed Energy Resources (DER). The solution follows a price and source-based REC management program, in which consumers day-ahead flexible loads (Flex Offers) are shifted according to electricity generation availability, prices and personal preferences, to balance the grid and incentivize user participation. The heuristic approach used in the proposed algorithms allows the optimization of energy resources in a distributed edge and fog approach with a low computational overhead. The simulations performed using real world energy consumption and flexibility data of a REC with 50 dwellings show an average cost reduction of 10.6% and an average increase of 11.4% in individual self-consumption. Additionally, the case-study demonstrates promising results regarding grid load balancing and the introduction of intra-community energy trading.

This study presents a methodology to fabricate Ti6Al4V cylindrical compacts with a highly porous core and dense shell with the purpose to mimic the bone microstructure. Compacts with different core diameters were obtained by conventionally press and sintering. Large pores were created with the aid of pore formers. Sintering kinetics was determined by dilatometry, whereas characterization was performed by X-ray computed tomography. Also, permeability was evaluated on the 3D microstructure and the mechanical strength was evaluated by compression tests. Results indicated that sintering is constraint by the different densification rates of the porous and dense layers. Nonetheless, defectless compacts were obtained due to neck bonding between Ti6Al4V particles. Large pores were located in the designed core with similar pore size distribution. Permeability increased following a power law as a function of the pore volume fraction. Stiffness of bilayer components was driven by the porous core, meanwhile, the strength resulted from the combination of both layers. Bilayer materials obtained showed a permeability and mechanical properties, as well as admissible strain (σy /E) similar to those of human bones.

While deforestation rates decline globally they are rising in the Western Amazon. Artisanal-scale gold mining (ASGM) is a large cause of this deforestation and brings with it extensive environmental, social, governance, and public health impacts, including large carbon emissions and mercury pollution. Underlying ASGM is a broad network of factors that influence its growth, distribution, and practices such as poverty, flows of legal and illegal capital, conflicting governance, and global economic trends. Despite its central role in land use and land cover change in the Western Amazon and the severity of its social and environmental impacts, it is relatively poorly studied. While ASGM in Southeastern Peru has been quantified previously, doing so is difficult due to the heterogeneous nature of the resulting landscape. Using a novel approach to classify mining that relies on a fusion of CLASlite and the Global Forest Change dataset, two Landsat-based deforestation detection tools, we sought to quantify ASGM-caused deforestation in the period 1984–2017 in the southern Peruvian Amazon and examine trends in the geography, methods, and impacts of ASGM across that time. We identify nearly 100,000 ha of deforestation due to ASGM in the 34-year study period, an increase of 21% compared to previous estimates. Further, we find that 10% of that deforestation occurred in 2017, the highest annual amount of deforestation in the study period, with 53% occurring since 2011. Finally, we demonstrate that not all mining is created equal by examining key patterns and changes in ASGM activity and techniques through time and space. We discuss their connections with, and impacts on, socio-economic factors, such as land tenure, infrastructure, international markets, governance efforts, and social and environmental impacts.

The present work proposed a low-cost portable device as an enabling technology for Smart Farms using multispectral imaging and Machine Learning in soil texture. Clay is an important factor for the verification and monitoring of soil use due to its fast reaction to chemical and surface changes. The system developed uses the analysis of reflectance in wavebands for clay prediction. The selection of each wavelength is performed through an LED lamp panel. A NoIR microcamera controlled by a Raspberry Pi device is employed to acquire the image and unfold it in RGB histograms. Results showed an good prediction performance with R2 of 0.96, RMSEC of 3.66% and RMSECV of 16.87%. The high portability allows the equipment to be used in a field providing strategic information related to soil sciences.

Lupus nephritis (LN) is a severe complication of systemic lupus erythematosus (SLE) and is considered one of the leading causes of mortality. Multiple immunological pathways are involved in the pathogenesis of SLE, which makes it imperative to deepen our knowledge about this disease's immunopathological complexity and explore new therapeutic targets. Since an altered redox state contributes to immune system dysregulation, this document briefly addresses the role of oxidative stress (OS), oxidative DNA damage, antioxidant enzymes, mitochondrial function, and mitophagy in SLE and LN. Although adaptive immunity's participation in the development of autoimmunity is undeniable, increasing data emphasize the importance of innate immunity elements, particularly the Toll-like receptors (TLRs) that recognize nucleic acid ligands, in inflammatory and autoimmune diseases. Here, we discuss the intriguing role of TLR7 and TLR9 in developing SLE and LN. Also included are the essential characteristics of conventional treatments and some other novel and little-explored alternatives that offer options to improve renal function in LN.

Chloride (Cl-) is applied in coffee in rates as a “macronutrient” due that potassium (K+) is one of the most demanded nutrients by the coffee plant, and the potassium muriate (KCl) bases fertilizer is one the most used by the coffee growers. Does not exist scientific evidence that addresses the question regarding with which is the influences of the Cl- applied in the K fertilization base on MOP on coffee growth, nutrient uptake, and nitrogen use efficiency (NUE). Over four years, two trials were conducted on greenhouse and field conditions to address these questions. The trials set up were designed to test the influence of increased Cl- and reduced S rates on biomass accumulation, nutrient uptake, and NUE. A significant effect of the Cl- rates on growth was observed under greenhouse conditions but a non-significant effect on yield under field conditions. Cl- and S significantly influence the NUE in coffee. The result allows us to conclude that Cl- rates need to be balanced with S rates and that Cl- applied as a macronutrient can improve the NUE in coffee when those rates do not exceed 180 mg. L-1 Cl- and 80 mg.L-1 S in the greenhouse and 150 kg.ha-1.year-1 Cl- and 50 kg. ha-1.year-1 S in field conditions. In practical terms, coffee farmers need to balance the K base fertilizers sources to improve the nutrient use efficiency, especially the NUE.

Celiac disease (CD) is an immune-mediated gluten-induced enteropathy that affects predisposed individuals of all ages. Many patients with CD do not report gastrointestinal symptoms making it difficult to reach an early diagnosis. On the other hand, CD is related to a wide spectrum of extra-intestinal manifestations, being dermatitis herpetiformis (DH) the best characterized. These associated conditions may be the clue for reaching the diagnosis of CD. Over the last years, there have been multiple reports of the association between CD and several cutaneous manifestations that may improve with a gluten-free diet (GFD). The presence of some of these skin diseases, even in absence of gastrointestinal symptoms, should give rise to an appropriate screening for CD. The aim of this paper is to describe the different cutaneous manifestations that have been associated to CD and the possible mechanisms involved.

This article presents a systematic mapping study dedicated to conduct a literature review on machine learning and IoT applied in the identification of diseases through heart sounds. This research was conducted between January 2010 and July 2021, considering IEEE Xplore, PubMed Central, ACM Digital Library, JMIR- Journal of Medical Internet Research, Springer Library, and Science Direct. The initial search resulted in 4,372 papers, and after applying the inclusion and exclusion criteria, 58 papers were selected for full reading to answer the research questions. The main results are: of the 58 articles selected, 46 (79.31%) mention heart rate observation methods with wearable sensors and digital stethoscopes, and 34 (58.62%) mention care with machine learning algorithms. The analysis of the studies based on the bibliometric network generated by the VOSviewer showed in 13 studies (22.41%) a trend related to the use of intelligent services in the prediction of diagnoses related to cardiovascular disorders.

Studies show that executive functions and motor development are associated among each other and with learning ability. A more technological lifestyle, related with digital culture, should be considered an important component to stimulate children. In addition, digital games constitute an element of the digital culture in which children are inserted. The aim of this study is to present a systematic mapping of the literature involving executive functions, motor development and the use of digital games in intervention programs for elementary school children, from 6 to 11 years old. Four databases were searched: PubMed, Scielo, Science Direct and SCOPUS, including publications between 2012 and March 2021. The initial results indicated 4881 works. After the selection process, 15 investigations that presented the central theme of the study were selected. The main results indicate that intervention strategies are quite heterogeneous. Most of the studies demonstrated significant positive effects after intervention protocols and were conducted in Europe and 46% of the studies were conducted in a school environment. No researches were identified that involved technological solutions involving executive functions, motor development and digital games in an integrated manner, constituting a field of future scientific research.

Keyhole laser beam welding (LBW) of stainless steel sheets with a gap in between is numerically simulated with a three-dimensional, transient multi-physical model for laser material processing. At first, the model’s ability to reproduce experimental results on a relatively coarse computational mesh within reasonable computing time, so as to serve as process optimization tool, is presented. An example of process optimization, where a given set of weld seam quality criteria is fulfilled by iteratively optimizing a secondary laser beam, is shown. The relatively coarse mesh, in combination with a good model calibration to the experimental conditions, allows for sufficiently fast simulations to use this approach for optimization tasks. Finally, using a finer spatial and temporal discretization, the dynamic processes in the vicinity of the keyhole leading to the formation of pores are investigated. The physical phenomena predicted by the simulation are coherent with experimental observations found in literature.

Traditional ways of validating satellite-derived sea surface temperature (SST) and sea surface salinity (SSS) products, using comparisons with buoy measurements, do not allow for evaluating the impact of mesoscale to submesoscale variability. Here we present the validation of remotely-sensed SST and SSS data against the unmanned surface vehicle (USV) – Saildrone – measurements from the Spring 2018 Baja deployment. More specifically, biases and root mean square differences (RMSD) were calculated between USV-derived SST and SSS values, and six satellite-derived SST (MUR, OSTIA, CMC, K10, REMSS, and DMI) and three SSS (JPLSMAP, RSS40, RSS70) products. Biases between the USV SST and OSTIA/CMC/DMI were approximately zero while MUR showed a bias of 0.2C. OSTIA showed the smallest RMSD of 0.36C while DMI had the largest RMSD of 0.5C. An RMSD of 0.4C between Saildrone SST and the satellite-derived products could be explained by the daily variability in USV SST which currently cannot be resolved by remote sensing measurements. For SSS, values from the JPLSMAP product showed saltier biases of 0.2 PSU, while RSS40 and RSS70 showed fresh biases of 0.3 PSU. An RMSD of 0.4 PSU could not be explained solely by the daily variability of the USV-derived SSS. Coherences were significant at the longer wavelengths, with a local maximum at 100 km that is most likely associated with the mesoscale turbulence in the California Current System.

The mass concentration of particulate matter (PM) has been systematically used in epidemiological studies as exposure indicator, to relate airborne concentrations with a wide variety of human health effects, which can be hardly explained by using this single parameter. In fact, PM is a “particle cocktail” that includes a complex mixture of compounds with a wide range of sizes, chemical compositions and emission sources. Current research hypothesizes that many of the adverse health effects are derived from oxidative stress in biological systems caused by the deposition of PM into the lungs. This emerging hypothesis is called the oxidative stress paradigm. In this commentary article we analize how this new paradigm could help to answer the as-of-yet unanswered questions related to the mechanism of action of PM pollution on human health. Acellular oxidative potential (OP) assays have been emerged as a promising approach to quantify the PM potential to induce oxidative stress and to relate it with the chemical composition and size distribution of PM. Recent researches have shown that the OP is related to the presence of metals, organic carbon, polyaromatic hydrocarbons and quinones. However, the association between PM and particle-induced toxicity is still largely unknown. Therefore, additional research is needed to identify the specific PM characteristic(s), such as its specific size, emission source or chemical content, which contribute the most to its redox activity. Thus, the OP measurements provide information that allows us to evaluate and integrate the toxic potential of PM in a unique parameter, whose relationships with emission sources, size distribution and/or chemical composition should be faced in the near future.

Daily thousands of people and goods move along Brazilian Federal highways. Traffic accidents are numerous on these highways and have a significant impact, whether on the economy or the health system. Identifying predictor variables, the probability of an event occurring and how to mitigate them are of paramount importance for the actions of the transit authorities that manage these roads. The main contribution of this study is the development of a predictive machine learning model which uses open data to shows graphically the critical points in the highways. This model is fully reproducible and can be applied to any region worldwide helping to minimize the number of accidents and to prevent deaths by automotive collisions. For this study, 43 variables were analyzed supporting the identification of the causes of accidents with fatal victims on the main highways in the south of Brazil. RoadLytics is proposed as a supervised machine learning model, using the Random Forest algorithm to analyze about 33 thousand occurrences between 2017 and 2020. An exploratory analysis of the data was carried out to support the modeling and to facilitate data visualization. In this sense, heat maps were developed to support the analysis and identification of potential risk areas. The results show that BR386 highway registers the highest number of fatal occurrences, regardless of the season. Additionally, concerning the weather conditions, the analysis shows that 52% of accidents occurred in favorable conditions, such as clear skies, victimizing 501 people. The driver’s lack of attention is the main reason for the accidents’ occurrences. Applying the developed model, an accuracy of 77% was achieved for the classification of fatal accidents.

Plant pathogenic fungi are the most important cause of losses in agriculture. In the face of the overuse of synthetic fungicides, natural products are an encouraging alternative to control these plant pathogenic fungi. In this study, we tested the antifungal capacity of metabolites produced by strains of the genus Streptomyces against the plant pathogenic fungi Alternaria alternata, Botrytis cinerea and Fusarium oxysporum. In addition, we investigated the feasibility of applying these metabolites in a postharvest setting for the control of B. cinerea on cherry tomato fruits. The results revealed the ability of the strains, especially Streptomyces netropsis, to inhibit the growth of plant pathogenic fungi and, in some cases, the sporulation of these fungi. In addition, we observed an interesting phenomenon in which Streptomyces strains physically encapsulated the mycelium of the fungi, which contributed to their inhibition. Finally, the protective activity of S. netropsis extract on Cherry tomato fruits infected with B. cinerea was demonstrated. In conclusion, this research opens the door to studies on the understanding of physical microbial interactions in natural environments and holds promise in agriculture, especially in the protection of agricultural products during the post-harvest stage as a safer and more sustainable alternative.

Molecular dynamics simulation is currently the theoretical technique eligible to simulate a wide range of systems from soft condensed matter to biological systems. However, of the excellent results that the technique has arrogated, this approach remains computationally expensive, but with the emergence of the new supercomputing technologies bases on graphics processing units graphical processing units-based systems GPUs, the perspective has changed. The GPUs allow performing large and complex simulations at a significantly reduced time. In this work, we present recent innovations in the acceleration of molecular dynamics in GPUs to simulate non-Hamiltonian systems. In particular, we show the performance of measure-preserving geometric integrator in the canonical ensemble, that is, at constant temperature. We provide a validation and performance evaluation of the code by calculating the thermodynamic properties of a Lennard-Jones fluid. Our results are in excellent agreement with reported data reported from literature, which were calculated with CPUs. The scope and limitations for performing simulations of high-throughput MD under rigorous statistical thermodynamics in the canonical ensemble are discussed and analyzed.

Breast cancer has an important incidence in the worldwide female population. Although alterations in the mitochondrial genome probably play an important role in carcinogenesis, the actual evidence is ambiguous and inconclusive. The purpose of the present work was to explore mitochondrial sequences of clinical cases with breast cancer from different origins and determine the polymorphisms associated. The search for complete and partial mtDNA sequences obtained from breast cancer patients and controls was performed in NCBI Genbank database. We identified 124 mtDNA sequences associated to breast cancer cases of which 86 were complete and 38 partial sequences. Of these 86 complete sequences, 52 belong to patients with a confirmed diagnosis of breast cancer and 34 sequences were obtained from healthy mammary tissue of the same patients used as controls. From mtDNA analysis, two polymorphisms with significative statistical differences were found in D130 in sequences analyzed: m.310del (rs869289246) in 34.6% (27/78) breast cancer cases and 61.7% (21/34) of controls; and m.315dup (rs369786048) in 60.2% (47/78) of breast cancer cases and 38.2% (13/34) of controls. Also, the variant m.16519T>C (rs3937033) was found in 59% of control sequences and 52% of breast cancer sequences with a significant statistical difference. Polymorphic changes are evolutionarily related to haplogroup H of Indo-European and Euro Asiatic origins, however, were found in all non-European sequences with breast cancer.

Every year around 800 000 people commit suicide, this represents one death every 40 seconds. In the search for possible biological biomarkers associated with suicide and/or psychiatric disorders, serum cholesterol levels have been extensively explored. Several studies have indicated that cholesterol and associated proteins, especially apolipoproteins (Apos), may play an important role in the diagnosis, prognosis, and susceptibility of suicide. Here, we describe the current knowledge and findings in the relationship between apolipoproteins and suicide.

Current hydrogen production is based on the reforming process leading to the emission of pollutants; therefore, a substitute production method is imminently required. Water electrolysis is an ideal alternative for large-scale hydrogen production, as it does not produce any carbon-based pollutant byproducts. Production of green hydrogen from water electrolysis using intermittent sources (e.g., solar, eolic) would facilitate clean energy storage. However, the electrocatalysts currently required for water electrolysis are noble metals, making this potential option expensive and inaccessible for industrial applications. Therefore, there is a need to develop electrocatalysts based on earth-abundant and low-cost metals. Nickel-based electrocatalysts are a fitting alternative because they are economically accessible. Extensive research has focused on developing nickel-based electrocatalysts for hydrogen and oxygen evolution. Theoretical and experimental work have addressed the elucidation of these electrochemical processes and the role of heteroatoms, structure, and morphology. Even though some works tend to be contradictory, they have lit up the path for efficient nickel-based electrocatalysts. For these reasons, herein, a review of recent progress is presented.

Today, across the most critical problems faced by hospitals and health centers are those caused by the existence of patients who do not attend their appointments. Among others, this practice generates waste of resources and increases the patients’ waiting list. To handle these problems, hospitals are actively trying to implement methods to reduce the idle time caused by patient no-shows. Many scheduling systems developed require predicting whether a patient will show up for an appointment or not. Although, a challenging problem resides in obtaining these estimates precisely. The goal of this work is to analyze how objective factors influence a patient not to attending their appointment, to identify the main causes that contribute to a patient’s decision, and to be able to predict whether or not the patient will attend the scheduled appointment. As a result, the obtained model is tested on a real dataset collected in a health center linked to the University of Vale do Itajaí (UNIVALI), which includes 25 features and about 5000 samples. The algorithm that produced the best results for the available dataset is the Random Forest classifier. It reveals the best recall rate (0.91), since it measures the ability of a classifier to find all the positive instances and achieves a receiver operating characteristic curve rate of 0.969.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

A basic pattern in the body plan architecture of many animals, plants and some molecular and cellular systems is five-part units. This pattern has been understood as a result of genetic blueprints in development and as a widely conserved evolutionary character. Despite some efforts, a definitive explanation of the abundance of pentagonal symmetry at so many levels of complexity is still missing. Based on both, a computational platform and a statistical spatial organization argument, we show that five-fold morphology is substantially different from other abundant symmetries like three-fold, four-fold and six-fold symmetries in terms of spatial interacting elements. We develop a measuring system to determine levels of spatial organization in 2D polygons (homogeneous or heterogeneous partition of defined areas) based in principles of regularity in a morphospace. We found that spatial organization of five-fold symmetry is statistically higher than all other symmetries studied here (three to ten-fold symmetries) in terms of spatial homogeneity. The significance of our findings is based on the statistical constancy of geometrical constraints derived from spatial organization of shapes, beyond the material or complexity level of the many different systems where pentagonal symmetry occurs.

In this article, we show theoretically and experimentally the formation of spin-waves band gaps in a magnonic crystal that was implemented by the deposition of periodic micro-structured strips of magnetite nanoparticles. A theoretical model describing the spectra of the transmitted spin-waves bandgaps is proposed. This is achieved using a simple model based on microwave transmission line theory and considering the presence of micro-structured strips of magnetite nanoparticles on the surface. Such magnonic crystal of equally spaced micro-structured strips of magnetite nanoparticles on the surface of an yttrium iron garnet thin film has been implemented and measured. The periodic micro-structured nanoparticles are deposited on the surface of such yttrium iron garnet single-crystal film grown on a gallium-gadolinium garnet substrate via dip-coating technique. Propagation of magnetostatic surface spin-waves is studied and it is shown that the presence of such periodic structure leads to the formation of spin-wave band gaps in the transmission characteristics. The spin-wave detection has been carried out using a pair of microwave antennas and a vector network analyzer. The results show that the periodic structure formed by the magnetite strips modifies the spectra of the transmitted spin waves producing band gaps.

Surveillance is the systematic data collection, analysis, and interpretation essential to planning and implementing control activities. The lack of success in control and surveillance elsewhere for the Ae. aegypti mosquito demands developing new accessible and effective strategies. This work aimed to develop and evaluate an adhesive and lure trap for household indoor and outdoor surveillance of Ae. aegypti. Based on a bibliographic review, four compounds with significant attraction percentages for Ae. aegypti were considered. Our more effective blend was determined by preliminary bioassays using the high-throughput screening system (HITSS) and 90 × 90 cm mosquito cages. We designed a low-cost, pyramid-shaped, sticky cardboard trap to incorporate the selected blend. Semi-field 2 x 2 m cages and field tests were conducted to evaluate its effectiveness through mosquito capture percentages. In laboratory tests, blend number 2 presented an attraction percentage of 47.5 ± 4.8%; while in semi-field cages, a 4-inch, 110-v powered fan was used to disperse the attractants, then a similar capture percentage of 43.2 ± 4.0 % was recorded. Field evaluation of the at-house indoor environment and comparing it with the golden standard BG-Sentinel trap recorded interesting results, i.e., an average of our prototype 6.0 ± 1.5 trapped mosquitoes versus 10.0 ± 2.6. In most Latin American countries, there is a lack of formal and accessible strategies for monitoring adult populations of Ae. aegypti, therefore, must develop tools that reinforce entomological surveillance methods.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

Obstacle-avoidance robots have become an essential field of study in recent years. This paper analyzes two cases that extend reactive systems focused on obstacle detection and its avoidance. The scenarios explored get data from their environments through sensors and generate information for the models based on artificial intelligence to obtain a reactive decision. The main contribution is focused on the discussion of aspects that allow comparing both approaches, such as the heuristic approach implemented, requirements, restrictions, response time, and performance. The first case presents a mobile robot that applies fuzzy logic to achieve soft turning basing its decision on depth image information. The second case introduces a mobile robot based on multi-layer perceptron and ultrasonic sensors to decide how to move in an uncontrolled environment. The analysis of both options offers perspectives to choose between reactive obstacle-avoidance systems based on ultrasonic or Kinect sensors, models that infer optimal decisions applying fuzzy logic or artificial neural networks, with key elements and methods to design mobile robots with wheels. Therefore, we show how AI or Fuzzy Logic techniques allow us to design mobile robots that learn from their “ experience ” by making them safe and adjustable for new tasks, unlike traditional robots that use large programs to perform a specific task.

The new Internet of Things (IoT) applications are enabling the development of projects that help monitoring people with different diseases in their daily lives. Alzheimer’s is a disease that affects neurological functions and needs support to maintain maximum independence and security of patients during this stage of life, as the cure and reversal of symptoms have not yet been discovered. The IoT-based monitoring system provides the caregivers’ support in monitoring people with Alzheimer’s Disease (AD). This paper presents an ontology-based computational model which receives physiological data from external IoT applications, allowing to identify of potentially dangerous behaviors for patients with AD. The main scientific contribution of this work is the specification of a model focusing on Alzheimer’s disease using the analysis of Context Histories and Context Prediction, which considering the state of the art, it is the only one that uses analysis of Context Histories to perform predictions. The research also proposes a simulator to generate activities of the daily life of patients allowing the creation of datasets. These datasets were used to evaluate the contributions of the model and were generated according to the standardization of the ontology. The simulator generated 1025 scenarios applied to guide the predictions, which achieved average accurary of 97.44%. The experiments also allowed the learning of 20 relevant lessons on technological, medical and methodological aspects of DCARE that are recorded in this article.

Membrane distillation techniques appear as one of the most promise alternative to guarantee the availability of potable water in time of scarce of this essential resource. For membrane preparation, polyvinylidene fluoride (PVDF) is preferred due to the easier synthesis procedures with respect to other fluorine based polymers. In this work, copper oxide nanoparticles (CuONPs) at different weight percent (wt.%), embedded in PVDF membranes supported on non-woven polyester fabric (NWPET) were prepared by the phase-inversion method, and characterized by spectroscopy (ATR-FTIR, Raman) and electron microscopy techniques (SEM). The PVDF deposited onto the NWPET was highly composed by its polar -phase (F()= 53 %) which was determined from the ATR-FTIR spectrum. The F() value was kept constant, in the whole range of CuONPs studied (2-10 wt.%) as was determined from the ATR-FTIR spectrum. The absence of signals corresponding to CuONPs in the ATR-FTIR spectra and the appearance of peaks at 297, 360 and 630 cm-1 in the Raman spectra of the membranes suggested that the CuONPs are preferably located in the inner of the membrane but not on its surface. The membrane morphologies were characterized by SEM. From the obtained SEM micrographs, a decrease and increase in the amount of micropores and nanopores, respectively, near to the surface and intercalated in the finger-like layer were observed. As result of the CuONPs addition, the nanopores in the sponge-like layer decrease in size. The values of water contact angle (WCA) measurements showed a trend to decrease from 94° to 80° upon the addition of CuONPs (2-10 wt.%) indicating a diminish in the hydrophobicity degree of the membranes. Apparently, the increase in the amount of nanopores near to the surface decreased the membrane roughness becoming less hydrophobic.

Cheese consumption provides humans with minerals, proteins, carbohydrates, and vitamins. In Mexico, several cheese varieties are produced, each with its texture, scent, and flavor. The artisanal cheeses made in the states of Tabasco and Chiapas —including, among others, the varieties named crema (cream), doble crema (double cream), oaxaca, panela, fresco, bola, poro, Cotija, and asadero— have a high demand in the domestic and foreign markets. The intensification of anthropic activity in these states causes an increased emission to the environment of contaminants like heavy metals, which could reach human foodstuffs through the food chains. In particular, heavy metal contents in cheeses consumed daily by these states' local population might represent a public health risk. Because of that, our objectives in this work were to determine the concentrations of lead, cadmium, nickel, copper, zinc, and iron in artisanal cheeses produced in the states of Tabasco and Chiapas, and to determine the values of the Hazard Quotient (HQ), Total Hazard Quotient (THQ), and Cancer Risk Total (CRT) for adult and young men and women. The results of our analyses of cheese samples from the states of Tabasco and Chiapas showed that the average concentrations (mg kg-1) of cadmium (0.0023±0.002, 0.0023±0.002 mg kg-1, respectively for each state), lead (0.0047±0.00, 0.0051±0.002), nickel (0.0039±0.0046, 0.0031±0.0039), copper (0.0199±0.021, 0.0202±0.022), zinc (0.1611±0.18, 0.194±0.21), and iron (61.84±4.23, 65.76±6.61 mg kg-1), the first three values lower than the limits established by the FAO/WHO and Codex Alimentarius. The value of THQ that we obtained was less than one, and that of CRT was within the limits established by the US-EPA, which means that the consumption of artisanal cheeses from Tabasco and Chiapas by humans does not imply a risk of disease or cancer.

The KARS gene encodes the aminoacyl-tRNA synthetase (aaRS) which activates and joins the lysin with its corresponding transfer RNA (tRNA), through the ATP-dependent aminoacylation of the amino acid. The KARS gene mutations have been linked to diverse neurologic phenotypes such as: neurosensorial hearing loss, leukodistrophy, microcephaly, developmental delay or regression, peripheral neuropathy, cardiomyopathy, impairment of the mitochondrial respiratory chain, hyperlactatemia, among others. This article presents the case of a Colombian pediatric patient with two pathological missense variants in a compound heterozygous state in the KARS gene.

Ribosomal proteins (RPs) mediate protein synthesis and stability of the ribosomal complex. RPs and rRNA form ribosomal subunits and ri-bosomes, the cellular machinery for protein synthesis, a fundamental biological process related to cell growth and proliferation. The differ-ences between paralogs within the same RP family have led them to ac-quire extraribosomal functions involved in plants' growth, develop-ment, and biotic and abiotic stresses. From transcriptomic analysis, it has been revealed that ribosomal proteins have a crucial role during MTs development. The RPLs; RPL11, RPL29 and RPL40 interact with PEBP family members (Phosphatidylethanolamine-binding proteins), poten-tial activators in the MTs development. In potatoes, genome editing is a promising technology to introduce crop breeding traits. Recently, the edition of the genome through the CRISPR/Cas9 system has made it the most efficient and powerful genetic modification method. Based on this, the gene modulation by overexpression and silencing in RPL11, RPL29 and RPL40 will guide us to understand the effect on the microtuberiza-tion process and produce improved potato plants with the capability of growing under adverse environments (biotic and abiotic stresses). By understanding the molecular biology mechanisms that RPs govern, we can improve crops under today's changing climatic conditions.

This work presents a multi-start algorithm for solving the capacitated vehicle routing problem with two-dimensional loading constraints (2L-CVRP) allowing for the rotation of goods. Researches dedicated to graph theory and symmetry considered the vehicle routing problem as a classical application. This problem has complex aspects that stimulate the use of advanced algorithms and symmetry in graphs. The use of graph modeling of the 2L-CVRP problem by undirected graph allowed the high performance of the algorithm. The developed algorithm is based on metaheuristics such as the Constructive Genetic Algorithm (CGA), to construct promising initial solutions; a Tabu Search (TS), to improve the initial solutions on the routing problem; and a Large Neighborhood Search (LNS), for the loading subproblem. Although each one of these algorithms allowed to solve parts of the 2L-CVRP, the combination of these three algorithms to solve this problem was unprecedented in the scientific literature. In our approach, a parallel mechanism for checking the loading feasibility of routes was implemented using multi-threading programming to improve the performance. Additionally, memory structures, like hash-tables, were implemented to save time by storing and querying previously evaluated results for the loading feasibility of routes. For benchmarks, tests were done on well-known instances available in the literature. The results proved that the framework matched or outperformed most of the previous approaches. As the main contribution, this work brings higher quality solutions for large-size instances of the pure CVRP. This paper involves themes related to the symmetry journal, mainly complex algorithms, graphs, search strategies, complexity, graph modeling, and genetic algorithms. In addition, the paper especially focuses on topic-related aspects of special interest of the community involved in symmetry studies, such as, graph algorithms and graph theory.

The interaction of the nervous, immune, and endocrine systems is crucial in the maintenance of homeostasis in vertebrates, and vital in mammals. The spleen is a key organ that regulates the neuroimmunoendocrine system. The Taenia crassiceps mouse system is an excellent experimental model to study the complex host-parasite relationship, particularly sex-associated susceptibility to infection. The aim of the present study was to determine the changes in neurotransmitters, cytokines, sex steroids, and sex-steroid receptors in the spleen of cysticercus-infected male and female mice, and the association of these different components with whole parasite counts. We found that parasite load was higher in female in comparison to male mice. The levels of the neurotransmitter epinephrine were significantly decreased in infected male animals. The expression of IL-2 and IL-4 in the spleen was markedly increased in infected mice; however, the expression of Interleukin (IL)-10 and Interferon (IFN)-γ decreased. We also observed sex-associated differences between non-infected and infected mice. Interestingly, the data show that estradiol levels increased in infected males but decreased in females. Our studies provide evidence that infection leads to changes on neuroimmunoendocrine molecules in the spleen during infection. These changes are dimorphic and impact the establishment, growth, and reproduction of T. crassiceps. Our findings support the key role of the neuroimmune network in determining sex-associated susceptibility to the helminth parasite.

Student-centered active learning (SCAL) shifts the focus from the teacher to the student. Implementing SCAL requires the development of new forms of assessment beyond memorization and comprehension. This paper aims to demonstrate the effectiveness of SCAL by analyzing student performance at different cognitive levels. In flipped classrooms, students completed tasks with varying cognitive demands. The tests measured knowledge (level 1), comprehension (level 2), application (level 3) and analysis (level 4). This approach to assessment assesses not only the acquisition of content, but also skills that are critical to a health science student's future career. The results of expository learning were compared with student-centered collaborative learning in the Anatomy and Embryology I course over three academic years. Student opinions were collected through 326 anonymous Wooclap® surveys. No differences in performance were found for low cognitive level questions. However, SCAL significantly improved performance on higher cognitive level questions that required problem solving and application of knowledge. Despite the benefits of SCAL, it requires more effort from both teachers and students. The current assessment system, which measures the quality of teaching, penalizes this effort and requires teachers to believe strongly in the effectiveness of SCAL.

The focus of this work lies in the construction of monitoring system designed in the form of a patch using a long-lasting potentiometric electrolyte concentration sensor from metal electrodes, in a galvanic cell configuration Mg(s)|NaCl(aq)|Cu(s). Initially, a mathematical analysis was conducted on the expected sensor output through the Nernst equation. The experimental phase involved conducting controlled tests in the laboratory using various molar concentrations of sodium chloride (NaCl) in aqueous solution. Results showed that the electrolyte sensor allows for monitoring electrolyte levels in NaCl in the range of 0.02 to 1 M/L, with electrode lifespan exceeding 10 days. On the other hand, when patch is using human sweat during controlled exercise routines, it showed the sensor's capability for monitoring changes in the subjects' hydration levels in real time. The sensor output potential is greater than 1.7 volts when the sensor electrodes are in contact with human sweat, which is equivalent to measuring molar concentrations at normal hydration and moderately high hydration levels. Sensor results indicate that the system can function in a self-powered manner without external batteries. Additionally, the extended lifespan of its electrodes allows for continuous monitoring of imbalances in the human body, showcasing the system capability for long-term health assessment.

Background: The incidence of prostate cancer (PC) has been risen annually. Despite the diagnosis is made mainly with non-metastatic PC, mortality is explained by the metastatic disease (mPC). Without a doubt there is an intermediate scenario in which patients have no mPC but will have initiated a metastatic cascade through an epithelial-mesenchymal transition. There is indeed a need for more and better tools to predict what patients will progress in the future to non-localized clinical disease or already have micrometastatic disease, and therefore, will clinically progress after primary treatment. Biomarkers for predicting mPC are still under development; there are few studies and not much evidence of their usefulness. Summary: This review is focused on tissue-based genomic biomarkers (TBGB) for predicting metastatic disease. We developed four main research questions that will attempt to answer according to the current evidence. Why is important to predict metastatic disease? Which tests are available to predict metastatic disease? What impact should there be on clinical guidelines and clinical practice in predicting metastatic disease? What are current prostate cancer treatments? Key Messages: Knowing useful predict tools could help determine which patients may need multimodal or adjuvant treatment even with a localized disease, and in consequence, what patients do not need more than a single modality of treatment. The importance of predicting metastasis is fundamental, given that once metastasis is diagnosed, the quality of life (QoL) and survival drop dramatically.

Nowadays, hydropower is the principal renewable; however, climate change increases extreme events such as floods, droughts, erosion, and sedimentation of rivers that produce uncertainty in hydroelectric generation. Thus, this document aims to analyze the climate change projections in the hydropower systems of Ecuador based on data from 14 projects studying the scenarios ac-cording to the Shared Socioeconomic Pathways from the Intergovernmental Panel on Climate Change. The study period starts from 2010 to 2020 with historical data, collects the tendency, defines a database year, and then projects the scenarios to 2050. The quantitative methodology uses a statistic on Ecuador's hydropower obtained inflow time series to calculate the deviation over the last years and develop a model to simulate future generation. The results show that the hydropower in Ecuador is expected to decrease considerably through 2050 due to meteorological changes. In this calculation of the Shared Socioeconomic Pathways, the selected scenarios show a reduction in SSP5 of 11.5%, SP2 of 16.2%, and SSP4 of 18.2% to 2050, concluding that the oppor-tunities for hydroelectric production facing climate change are variable, but the challenges are broad. In Ecuador, the projections of hydropower plants represent a sensitive issue of their re-ductions, especially knowing that the country had an energy grid in 2020 that depended on 87% of hydroelectric production.

Among the many Lysosomal Storage Disorders (LSDs) that would benefit from the establish-ment of novel cell models, either patient-derived or genetically engineered, is Mucopolysaccha-ridosis type II (MPS II). In fact, even though a specific therapeutic approach does exist for this disorder (Enzyme Replacement Therapy, ERT, with recombinant human IDS) and haematopoiet-ic stem cell transplantation (HSCT) may also hold promise whenever the disorder is diagnosed soon enough, both approaches have their own drawbacks. Here we present our results on the establishment and characterization of two MPS II pa-tient-derived stem cell line(s) from deciduous baby teeth. To the best of our knowledge, this is the first time a stem cell population is isolated from LSD patient samples obtained from the oral cavity. Taking into account our results on the molecular and biochemical characterization of those cells and our first insights on their subcellular MPS phenotype, we consider these cells will be a valuable tool for both pathophysiological assessments and drugs screenings. Ultimately, we believe patient-derived dental pulp stem cells (DPSC) may represent a feasible alternative to induced pluripotent stem cells (iPSC) in many labs with standard cell culture con-ditions and limited (human and economic) resources.

In this letter, we show an alternative low-cost fabrication method to obtain poly(dimethyl siloxane) (PDMS) microfluidic devices. The proposed method allows the inscription of micron resolution channels on polystyrene (PS) surfaces, used as a mold for the wanted microchip’s production, by applying a high absorption coating film on the PS surface to ablate it with a focused low-power visible laser. The method allows obtaining micro resolution channels at powers between 2 and 10mW and can realize any two-dimensional polymeric devices. The effect of the main processing parameters on the channel’s geometry is presented.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

Applying a procedure similar to that of E.S. Bring, by using a 4^th degree Tschirnhaus transformation, it was possible to transform the Bring-Jerrard normal quintic (BJQ) equation into a De Moivre form (DMQ), so that it could be solved by radicals. The general solution by radicals of the De Moivre equations of any degree is presented. By the same procedure the BJSx (normal sextic) equation was taken to another one without the 2^nd, 4^th and 6^th terms which was transformed into a cubic (solvable) equation. By applying a 6^th degree Tschirnhaus transformation to the BJSp (normal septic) equation its Bring-Jerrard binormal (without the 2^nd, 3^rd, 4^th and 5^th terms) form was obtained.

Rheumatoid arthritis (RA) is an autoimmune disease mainly characterized by joint inflammation. It presents extra-articular manifestations, with the lungs one of the affected areas. Among these, damage to the pulmonary interstitium (Interstitial Lung Disease -ILD) has been linked to proteins involved in the inflammatory process and related to extracellular matrix deposition and lung fibrosis establishment. Peptidyl arginine deiminase enzymes (PAD), which carry out protein citrullination, play a role in this context. A genetic association analysis was conducted on genes encoding two PAD isoforms, PAD2 and PAD4. This analysis also included ancestry informative markers and protein level determination in samples from patients with rheumatoid arthritis, RA-associated ILD, and clinically healthy controls. Significant single nucleotide variations (SNV) and a haplotype were identified as susceptibility factors for ILD-RA development. Elevated levels of PAD4 were found in ILD-RA cases, while PADI2 showed an association with RA susceptibility. This document presents the data obtained from the conducted research, which has been published.

This paper presents additional results of the generalized bathtub model for urban networks, including a simpler derivation and exact solutions for uniformly distributed trip lengths. It is shown that in steady state this trip-based model is equivalent to the more parsimonious accumulation-based model, and that the trip-length distribution has merely a transient effect on traffic dynamics, which converge to the same point in the macroscopic fundamental diagram (MFD). To understand the statistical properties of the system, a queueing approximation method is proposed to compute the network accumulation variance. It is found that (i) the accumulation variance is much larger than predicted by traditional queueing models, due to the nonlinear dynamics imposed by the MFD, (ii) the trip-length distribution has no effect on the accumulation variance, indicating that the proposed formula for the variance might be universal, (iii) the system exhibits critical behavior near the capacity state where the variance diverges to infinity. This indicates that the tools from critical phenomena and phase transitions might be useful to understand congestion in cities.

Antimicrobial-resistant bacteria represent a serious threat to public health. Among these bacteria, Salmonella is of high priority because of its morbidity levels and its ability to induce different types of cancer. Aim: This study aimed to identify Salmonella strains encoding genes linked to the promotion of precancerous lesions and to isolate a bacteriophage to evaluating its preclinical potential against these bacteria. Methodology: An epidemiological approach based on wastewater analysis was employed to isolate Salmonella strains and detect genes associated with the induction of precancerous lesions. Antimicrobial susceptibility was assessed by disk diffusion method. A bacteriophage was isolated via the double agar technique, and its morphological characteristics, stability, host range, replication dynamics and ability to control Salmonella under different conditions were evaluated. The bacteriophage genome was sequenced and analyzed using bioinformatics tools. Results: Thirty-seven Salmonella strains were isolated, 17 of which contained the five genes associated with precancerous lesions induction. These strains exhibited resistance to multiple antimicrobials, including fluoroquinolones. A bacteriophage from the Au-tographiviridae family with lytic activity against 21 bacterial strains was isolated. This phage ex-hibited a 20 min replication cycle, releasing 52 ± 3 virions per infected cell. It demonstrated sta-bility and efficacy in reducing Salmonella concentration in simulated gastrointestinal conditions, and its genome lacked genes that represent a biosafety risk. Conclusion: This bacteriophage shows promising preclinical potential as a biotherapeutic agent against Salmonella.

In the area of health, namely hospitals, we can agree that the intrinsic need to have multidisciplinary teams, highly specialized and indispensable resources leads us to a degree of complexity that requires, daily, the best performance, not running away from the logistics area to the rule. The centralization of resources, namely distribution warehouses, emerges as a challenge and possible solution for health institutions to respond in the best possible way to their main purpose: to put the right material in the right place at the right price in the right time space. As regards the advantages of this type of organization, there are several authors who argues that the need for human resources training, ease of coordination and the use of economies of scale are the main advantage. As far as the disadvantages are concerned, there is no special agreement on them, there are disparate factors from author to author, such as: routine, centralization, objectives or operation costs.

The number of physical devices connected to the Internet such as vehicles, household appliances and other "things" has been steadily increasing in recent years, thus forming the basis for the Internet of Things (IoT). IoT ecosystem extends beyond country borders and application domains, combining thousands of versatile devices that differ in terms of their structures, capabilities, and available resources. It is therefore not surprising that the landscape of wireless communication technologies and the degree of IoT devices available today is excessively broad and diverse. Interference between networks leads to frame collisions and consequent packet loss. Frame collisions occur when two or more packets overlap in time and frequency and use the same Long Range (LoRa) parameters, i.e. the same Spreading Factor (SF), Bandwidth (BW) and Carrier Frequency (CF). When most devices use the same configuration, collision probability is higher. The probability of frame collisions is also affected by traffic characteristics, particularly the periodicity of the transmission and the payload size. Larger payload sizes and more frequent transmissions accumulate with higher Time on Air (ToA) and channel occupancy [1]. Transmission powers and the location of the gateways also influences this situation. The aim of this experimental work is to verify the effects of collisions and interference in Long Range Wide Area Network (LoRaWAN), regarding the periodicity of transmissions and the payload sizes in a context of an inter-SF interference scenario. And to validate measuring tools like Received Signal Strength Indicator (RSSI), ToA and Packet Delivery Ratio (PDR) in the reliability of a network. We validate our conclusions by analyzing ToA according with RSSI and different data sizes, the RSSI for different SFs and different data sizes and finally the packet loss through the PDR for a better understanding of the reliability of packet transmission in our link. In the end we conclude that in an environment with inter-SF interference, the choice of SFs and packet lengths impacts ToA. When dealing with multiple devices near gateways, different SFs and varying packet lengths can lead to increased latency and longer ToA. Consequently, the risk of packet loss becomes more significant, especially if the signal-to-interference ratio (SIR) is low. This limitation will therefore affect scalability, particularly in Non-Line-Of-Sight (NLOS) scenarios.

Cardiovascular diseases (CVD´s) continue as the primary cause of death worldwide. During the past couple of years, and with the surge of the COVID-19 pandemic, deaths linked to CVD´s were -slightly overshadowed by those deaths related to COVID-19, albeit during the highest peaks of the pandemic. The present study derived form understanding the correlation between both diseases, from the standpoint of patients already diagnosed with CVD´s (n = 41883) and what comorbidities had the highest influence on overall patient death (n = 3637). Obesity, hypertension, and diabetes are all linked to worsening the outcome of COVID-19 positive patients, hence they were considered when looking at the overview of all CVD positive patients. Our finding showed that 1697 deaths were related to diabetes (p < 0.001), 987 deaths were related to obesity (p < 0.001), and lastly 2499 deaths were attributed to hypertension (p < 0.001) individually. Using logistic regression modeling, we found diabetes (OR: 1.744, p < 0.001) and hypertension (OR: 2.179, p < 0.001) had a high impact on patient deaths. Hence, having a CVD diagnosis, with hypertension and/or diabetes seems to increase the likely-hood of complication leading to death in COVID-19 positive patients.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

In ref. [1], we pointed out that certain anomalies observed in the published data for ac magnetic susceptibility of a room temperature superconductor reported in Nature 586, 373 (2020) [2] would be cleared up once the measured raw data were made available. Part of the measured raw data were recently posted in arXiv:2111.15017 [3]. Here we report the results of our analysis of these raw data and our conclusion that they are incompatible with the published data. Implications of these results to the claim that the material is a room temperature superconductor are discussed.

Pancreatic cancer leads the most common lethal tumor in America. This lethality is related to limited treatment options. Conventional treatments involve a non-specific use of chemotherapeutical agents like 5-FU, capecitabine, gemcitabine, cisplatine, oxaliplatine, or irinotecan, that produce several side effects. This review we focus on the use of targeted nanoparticles as an alternative to the standard treatment for the pancreatic cancer. The principal objective of the use of nanoparticles is the reduction in side effects that conventional treatments produce, mostly because of their nonspecificity. Currently, several molecular markets of pancreatic cancer cells have been studied to target nanoparticles and improve the actual treatment. Therefore, properly functionalizated nanoparticles with specific aptamers or antibodies can be used to recognize pancreatic cancer cells and once cancer is recognized, these nanoparticles can attack the tumor by drug delivery, hyperthermia, or gene therapy.

This paper has a twofold objective. The first aim is to present a comprehensive bibliographical analysis of journal articles and book chapters on fuzzy-random option pricing (FROP) over the WoS and SCOPUS databases. It follows PRISMA criteria and takes special care of developments in continuous time. Thus, we described the principal findings about the research streams, outlets and authors of this topic and lets us suggest further research. The second contribution is motivated by the fact that the bibliographical revision has identified a lack of developments on equilibrium models on the yield curve. This question motivates extending Vasicek’s yield curve equilibrium model to introduce fuzziness in the parameters that govern interest rate movements (speed of reversion, equilibrium short-term interest rate, and volatility). Likewise, this paper develops an empirical application on the term structure of fixed income public bonds with the highest credit rating in the Euro area.

This study examines the feasibility of using event-related potentials (ERPs) obtained from electroencephalographic (EEG) recordings as biomarkers for long-term memory item classification. Previous studies have identified old/new effects in memory paradigms associated with explicit long-term memory and familiarity. Recent advancements in convolutional neural networks (CNNs) have enabled the classification of ERP trials under different conditions and identification of features related to neural processes at the single-trial level. We employed this approach to compare three CNN models with distinct architectures using experimental data. Participants (N = 25) performed an association memory task while recording ERPs that were used for training and validation of the CNN models. The EEGNET-based model achieved the most reliable performance in terms of precision, recall, and specificity compared with the shallow and deep convolutional approaches. The classification accuracy of this model reached 70% for known items and 62% for unknown items. Good overall accuracy requires a trade-off between recall and specificity and depends on the architecture of the model and the dataset size. These results suggest the possibility of integrating ERP and CNN into online learning tools and identifying the underlying processes related to long-term memorization.

Background. It is well established that human milk feeding contributes in limiting lung disease among vulnerable neonates. The primary aim of this research was to compare the need for mechanical ventilation of human milk-fed sick neonates with that of formula-fed sick neonates. Methods. All late preterm and full term infants from a single center with findings of sepsis, from 2002 to 2017, were identified. Data regarding infant feeding during hospital admission were recorded. Multivariate logistic regression analyses were performed to assess the impact of the type of milk on ventilation support and main neonatal morbidities. Results. The total number of participants was 322 (human milk group = 260, exclusive formula group = 62). On bivariate analysis, 72% of human milk-fed neonates did not need oxygen therapy nor respiratory support versus 55% of their formula-fed counterparts (P<0.0001). Accordingly, invasive mechanical ventilation was required by 9.2% of human milk-fed infants versus 32% of their formula-fed counterparts (P=0.0085). These results hold true in multivariate analysis, indeed human milk-fed neonates were more likely to require less respiratory support (OR=0.44; 95% CI: 0.22, 0.89) when compared to those who were exclusively formula-fed. Conclusion. Human milk feeding might minimize exposure to mechanical ventilation.

Biodiversity conservation questions human practices towards biodiversity and, therefore, largely conflicts with ordinary societal aspirations. Decisions on the location of protected areas, one of the most convincing conservation tools, reflect such a competitive endeavor. Operations Research (OR) brings a set of analytical models and tools capable of resolving the conflicting interests between ecology and economy. Recent technological advances have boosted the size and variety of data available to planners, thus challenging conventional approaches bounded on optimized solutions. New models and methods are requested to use such a massive amount of data in integrative schemes addressing a large variety of concerns. Here, we provide an overview on the past, present and future challenges that characterize spatial conservation models supported by OR. By enlarging the spatial, temporal, taxonomic and societal horizons of biodiversity conservation planners navigate around multiple bio-socioeconomic equilibria and are able to decide on cost-effective strategies to improve biodiversity persistence.

Background: This study aimed to estimate the prevalence of sexualized drug use (SDU) in gay, bisexual, and other men who have sex with men living with HIV (HIV+GBMSM) in Madrid during 2019/2020 and compare it with data from 2016/2017. Methods: We analysed the frequency of SDU in a sample of HIV+GBMSM attending HIV clinics, who participated in an anonymous online survey regarding sexual behaviour and recreational drug use. The association between SDU, sexual risk behaviours, and STIs was evaluated. The methodology employed in the present study(U-SEX-2) in 2019/2020 was consistent with that of a previous study(U-SEX-1) in 2016/2017. Results: The study included 424 HIV+GBMSM, with a mean age of 40(10.43) years. Overall, 94% (396) reported being sexually active. Additionally, 33% (140) had been diagnosed with an STI within the previous year. Moreover, 54% (229) had used drugs in the last year, 25% (107) engaged in SDU, and 15% (17) reported engagement in slamsex. After adjusting for confounding factors, SDU was associated with STIs, fisting, unprotected anal intercourse, and having &gt; 24 sexual partners in the last year. According to the DUDIT test scores, 76% (81) probably had problematic drug use (≥6 points), and 5% (8) probable drug dependence (≥25 points). When comparing the U-SEX-1(2016/2017) data with the U-SEX-2(2019/2020) data, no significant differences were found in the proportion of participants practicing SDU or slamsex. Conclusion: The prevalence of SDU among HIV+GBMSM has remained high in recent years and without significant changes. We observed a clear association between SDU, high-risk sexual behaviors, STIs, and the risk of drug related problems.

The current study aims to first, isolate H. pylori in cultures from gastric biopsy samples and test their susceptibility. Secondly, we aim to assess the efficacy of the standard triple therapy from patients coming of the western central region of Colombia. Patients with H. pylori positive re-ceived standard triple therapy with PPI [40 mg b.i.d.], clarithromycin [500 mg b.i.d.], amoxicillin [1g b.i.d.] for 14 days. Thereafter, antibiotic susceptibility of the isolates was assessed by E-Test. From 94 patients enrolled, 67 were positive for H. pylori by histology or culture. Resistance to metronidazole, levofloxacin, rifampicin, clarithromycin and amoxicillin was 81, 26.2, 23.9, 19 and 9.5%, respectively. No resistance was found for tetracycline. 54 patients received standard triple therapy, 48 attended follow-ups testing and of them, 30 had resistance test reports. Overall eradication rate was 81.2%, 4 patients underwent second-line management and only one patient remained H. pylori positive by urea breath test during the follow-up [six weeks]. Eradication was significantly higher in patients with clarithromycin susceptible than in resistant strains [95.6% vs. 42.8% p= 0.001]. The updated percentages of resistance to clarithromycin in this geographical area have increased, so this value must be considered when choosing the treatment regimen.

Earthworms are iteroparous organisms with indeterminate growth, i.e. they continue to increase in size throughout their life and after completion of sexual development. Terrestrial oligochaetes vary greatly in size. Depending on the species, adult earthworms can reach between 10 mm and 3 m in length and between &lt;1 mm and &gt;25 mm in width, with most being of length 5-15 cm. Among the more than 7000 species described to date, very few (~20) reach lengths greater than 1 m. The longest earthworm on record is Amynthas mekongianus, which is found in the mud banks of the Mekong River in Southeast Asia and which reaches almost 3 m in length. It is about the same size as Megascolides australis, the ‘Giant Gippsland Earthworm’. These atypically giant earthworm species remain a scientific curiosity in terms of their biology, but they cannot be considered cases of gigantism. Gigantism occurs when organisms are much larger than normal or exhibit excessive growth. Earthworms obtain energy from the organic matter on which they feed, and their growth mainly depends on the quality of the resource and on the species, as well as on food availability, environmental factors, which can directly or indirectly affect growth by modifying food availability, and other factors such as competition. This is particularly evident in earthworms, which display indeterminate growth and large species-dependent variations in size. The biology, life cycle and growth and reproduction rates of Eisenia fetida (Savigny 1826) and Eisenia andrei (Bouché 1972), the earthworm species most commonly used in vermicomposting and vermiculture, have been widely reported. Here we present details of the enormous growth of individual specimens of Eisenia andrei and Dendrobaena hortensis reared under particular culture conditions and fed a special diet. Individuals almost 20 times the average weight of individuals of the species have been obtained. Possible explanations for this interesting phenomenon are discussed.

It was recently shown that urban networks might exhibit two different critical points, one for the percolation of congested links through the network, and another one for the flow of vehicles through the network. It was observed that the percolation critical point happens after the flow critical point, where network throughput is maximized. This result is important because if a causal relationship exists between these two processes, it can be leveraged for improving control methods to avoid network collapse. This paper presents the results of numerical experiments to understand the possible causal relationship between the percolation and flow processes by focusing on the relative timing between the two critical points. The goal is to understand the impacts of important factors such as: (i) urban network type: long- and short-block networks, (ii) signal timing control type: fixed, random, responsive, and (iii) route choice: turning proportions at intersections. We find that the threshold density $k^*_c$ to determine if a link is congested has the main impact on the timing of the percolation transition, where lower values trigger earlier transitions. This implies that $k^*_c$ can be set such that the percolation transition happens before the flow critical point, opening the door for improved congestion management strategies. If $k^*_c$ is set to the average network critical density, maximum network throughput happen simultaneously with the percolation transition. Surprisingly, it appears that these results, and more generally, the relationship between the percolation and flow processes is independent of (i) and (ii) above.

Glucose is a simple sugar molecule. The sugar molecule is chemically symbolised as C6H12O6. This means that the glucose molecule contains 6 carbon atoms (C), 12 hydrogen atoms (H) and 6 oxygen atoms (O). In human blood, the molecule glucose circulates as blood sugar. Normally after eating or drinking, our body breaks down the sugars in food and uses them to obtain energy for our cells. To do this, our pancreas produces insulin. Insulin "pulls" sugar from the blood and puts it into the cells for use. If someone has diabetes, their pancreas can't produce enough insulin. As a result, the level of glucose in the blood rises. This can lead one to many potential complications, including blindness, disease, nerve damage, amputation, stroke, heart attack and damage to blood vessels etc. In this study, a non-invasive method for monitoring blood glucose has been developed and is therefore easily usable. The device developed can measure the glucose level continuously and eliminates the disadvantages of the invasive system. Near-IR sensors (optical sensors) were used to estimate the concentration of glucose in the blood; these sensors have a wavelength of 940 nm. The sensor is placed on the tip of the finger and the output of the optical sensor is then connected to the microcontroller at the analogue input. Another sensor used, but only to provide more medical information was the heartbeat sensor. After processing and regression analysis, the glucose level is predicted, and data is sent via the Bluetooth network to a developed APP. The results of the implemented device were compared with available invasive methods. The study consists of a hardware platform inserted into an armband and then a small black parallelepiped-shaped box in which the optical sensors are inserted. The hardware consists of a microcontroller, a Near-IR optical sensor, a heartbeat sensor and a Bluetooth module.

Among cross-sectional imaging modalities, computed tomography (CT) is more available and faster; however, magnetic resonance (MR) performs better in terms of sensitivity and specificity, due to its higher contrast resolution. The appearance of peritoneal deposits on CT and MR depends mainly on the primary tumour histology: in case of unknown primary tumour (3-5% of cases), their behaviour at imaging may provide insights on the tumour origin. The time-point of tumour evolution, previous or ongoing treatments and the peritoneal spaces where they occur, also play an important role in determining the appearance of peritoneal deposits. Thus, knowledge of peritoneal anatomy and fluid circulation is mandatory in detection and characterization of peritoneal deposits. Several benign and malignant conditions may show similar imaging features that overlap those of PC, making the differential diagnosis challenging. Clinical history, laboratory findings and previous imaging examinations must be considered to achieve the correct diagnosis.

Biosensors are analytical devices that utilize biological interactions to detect and quantify clinical biomarkers, contaminants, allergens, and microorganisms. They combine different disciplines including analytical chemistry, molecular biology, and electrical engineering. Biosensors operate by coupling a bioreceptor, such as nucleic acid or proteins, with a transducer that converts the biological interaction into an electrical signal. Electrochemical and optical transduction are commonly used approaches due to their high detection capability and compatibility with miniaturization. Biosensors provide both high specificity and sensitivity and can be integrated into low-cost microfluidic platforms for rapid and point-of-care applications. These attributes make these devices valuable tools in analytical chemistry, particularly for early diagnostic applications. However, conventional biosensors face challenges related to the immobilization of biorecognition elements on the transducer surface, leading to issues like lost of sensitivity and selectivity. To address these problems, the introduction of nanomaterials, particularly magnetic nanoparticles (MNPs) and magnetic beads (MBs), has been implemented. MNPs combine their magnetic properties with other interesting characteristics such as small size, high surface-to-volume ratio, and excellent biocompatibility. They can be tailored for specific applications and have been extensively used in various fields, including biosensing and clinical diagnosis. Furthermore, MNPs simplify sample preparation by isolating target analytes through magnetic separation, thus improving sensitivity, and reducing analysis time and interference phenomena. The synthesis and modification of MNPs play a crucial role in adjusting their properties for different applications. This review presents an overview of the synthesis and surface modifications of magnetic nanoparticles, their role in the development of biosensors and bioassays, and their applications across various scientific areas.

Current adaptive cruise control (ACC) systems adopt fixed desired time headway, which leads to an abrupt speed reduction after being cut-in by a lane changer in front or when changing lanes too close to the new leader. In contrast, human drivers behave differently and feature a variable spacing within 20 or 30 seconds right after a cut-in or lane change. Motivated by the smooth transition found in driver relaxation, the paper aims to incorporate relaxation into ACC systems. Based on the open-source ACC platform, Openpilot, Comma.ai, the paper proposes a feasible relaxation model compatible with current factory ACCs, which has also been tested using a market car with stock ACC hardware. The study further investigates the impact of relaxation ACC on traffic operation. Numerical simulation suggests that incorporating relaxation into ACC can help: i) reduce the magnitude of speed perturbations in both cut-in vehicles and followers; ii) stabilize the lane-changing traffic by reducing the speed variance and prevent the lateral propagation of congestion, and iii) increase the average vehicle speed and capacity in merging traffic.

Audio recording in classrooms is a common practice in educational research, with applications ranging from detecting classroom activities to analysing student behaviour. Previous research has employed neural networks for classroom activity detection and speaker role identification. However, these recordings are often affected by background noise that can hinder further analysis, and the literature has only sought to identify noise with general filters and not specifically designed for classrooms. Although the use of high-end microphones and environmental monitoring can mitigate this problem, these solutions can be costly and potentially disruptive to the natural classroom environment. In this context, we propose the development of a neural network model that can specifically detect and filter out background noise in classroom recordings. This model would allow the use of lower quality recordings without compromising analysis capability, thus facilitating data collection in natural educational environments and reducing the costs associated with high-end recording equipment.

Opuntia ficus-indica has always interacted with many phytophagous insects at its center of origin; two of them are Dactylopius coccus and D. opuntiae. D. coccus, or true cochineal, is produced to extract carminic acid, and D. opuntiae or wild cochineal is a key invasive pest of O. ficus-indica in more than 20 countries around the world. Despite the economic and environmental relevance of this cactus and, D. opuntiae and D. coccus, there are few studies that have explored volatile organic compounds (VOCs) derived from the plant-insect interaction. The aim of this work was to determine VOCs of D. coccus and D. opuntiae feeding on cultivars suitable for their development and to identify different VOCs in cladodes infested by each Dactylopius species. Volatiles were identified through their essential oils, which were obtained by hydrodistillation. A total of 66 VOCs from both Dactylopius species were identified, and 125 from the Esmeralda and Rojo Pelón cultivars infested by D. coccus and D. opuntiae, respectively, were determined. Differential VOCs production due to infestation by each Dactylopius species was also found. Some changes in methyl salicylate, terpenes such as linalool or the alcohol p-vinylguaiacol were related to Dactylopius feeding on cladodes of their respective cultivars. Changes in these VOCs and their probable role in plant defense mechanisms should receive more attention because this knowledge could improve D. coccus rearing, or to its inclusion in breeding programs for D. opuntiae control in regions where it is a key pest of O. ficus-indica.

Three-Dimensional reconstruction of the corneal surface provides a powerful tool for managing corneal diseases. This study proposes a novel method for reconstructing the corneal surface from elevation point clouds, using modal schemes capable of reproducing corneal shapes using surface polynomial functions. The multivariable polynomial fitting was performed using a non-dominated sorting multivariable genetic algorithm (NS-MVGA). Standard reconstruction methods using least-squares discrete fitting (LSQ) and sequential quadratic programming (SQP) were compared with the evolutionary algorithm-based approach. The study included 49 eyes of 49 patients (ages 11-63) sorted in two groups: control (33 eyes) and keratoconus (KC) (16 eyes). Tomographic information (Sirius, Costruzione Strumenti Oftalmici, Italy) was processed using Matlab. The goodness of fit for each method was evaluated using mean squared error (MSE), measured at the same nodes where the elevation data were collected. Polynomial fitting based on NS-MVGA improves MSE values by 86% compared to LSQ-based methods in healthy patients. Moreover, this new method improves aberrated surface reconstruction by 43% for Amsler-Krumeich (AK) Grade 1 keratoconus patients. Finally, significant improvements were also found in morpho-geometric parameters, such as asphericity and corneal curvature radii.

Background: It is well known the adverse effect of mercury exposure on pregnant women and newborns. Interactions between environmental factors and individual genetic susceptibility have been identified, particularly polymorphisms of codifying genes for the Glutathione S-transferase family (GSTs). Herein, we report a case series of patients with high Hg levels in biosamples. Case Series: Fourteen cases with high Hg levels were identified. Non-occupational or home exposure risk factors were identified. All mothers reported fish consumption during pregnancy. Almost 60% of the individuals were null for either one GSTs gene. To date, in the subsequent mother-child pairs toxicology controls no signs or symptoms of poisoning were identified and most of the mercury levels decreased and are below the accepted limit. Discussion: In this case series we found some similarities with the literature; among them, the relation of Hg ratio in maternal blood and umbilical cord, a possible exposure factor is the consumption of fish during pregnancy and, the high levels of Hg may be related with susceptibility biomarkers such as GSTs gene polymorphisms. This case series highlights the need to develop studies that evaluate the interactions between environmental factors and individual genetic susceptibility. Additionally, the importance of evaluating which Colombian fish species present the highest levels of Hg.

The fact that real dissipative (entropy producing) processes may be detected by non–comoving observers (tilted), in systems that appear to be isentropic for comoving observers, in general relativity, is explained in terms of the information theory, in analogy with the explanation of the Maxwell's demon paradox.

Data from NASA’s Soil Moisture Active Passive Mission (SMAP) and from the California Cooperative Oceanic Fisheries Investigations (CalCOFI) were used to examine the freshening that occurred during 2015-2016 in the Southern California Current System. Overall the freshening was found to be related to the 2014-2016 Northeast Pacific Warm Anomaly. The primary goal was to determine the feasibility of using SMAP data to observe the surface salinity signal associated with the warming. As a first step direct comparisons were done with salinity from the CalCOFI data at one-meter depth. During 2015 SMAP was saltier than CalCOFI by 0.5 PSU, but biases were reduced to < 0.1 PSU during 2016. South of 33°N, and within 100 km of the coast, SMAP was fresher in 2015 by almost 0.2 PSU. CalCOFI showed freshening of 0.1 PSU. North of 33°N SMAP and CalCOFI saw significant freshening in 2016, SMAP by 0.4 PSU and CalCOFI by 0.2 PSU. Differences between SMAP and CalCOFI are consistent with the increased stratification in 2015 and changes in the mixed layer depth.

In this paper, we revisit a modified version of the classical Whitehead's theory of gravity in which all possible bilinear forms are considered to define the corresponding metric. Although, this is a linear theory that fails to give accurate results for the most sophisticated predictions of general relativity, such as gravity waves, it can still provide a convenient framework to analyze some new phenomena in the Solar System. In particular, recent development in the accurate tracking of spacecraft and the ephemerides of planetary positions have revealed certain anomalies in relation with our standard paradigm for celestial mechanics. Among them the so-called flyby anomaly and the anomalous increase of the astronomical unit play a prominent role. In the first case the total energy of the spacecraft changes during the flyby and a secular variation of the semi-major axis of the planetary orbits is found in the second anomaly. For this to happen it seems that a net energy and angular momentum transfer is taken place among the orbiting and the central body. We evaluate the total transfer per revolution for a planet orbiting the Sun in order to predict the astronomical unit anomaly in the context of Whitehead's theory. This could lead to a more deeply founded hypothesis for an extended gravity model.

Study of micro-RNA regulatory networks (known as miRNA’s or miR’s), during development and in known pathologies have been the basis of study over the past decades. Herein, we recapitulate these findings in order to highlight the best underlying mechanisms found to date. We also seek to elucidate how miRNA dysregulation can be associated with many cardiovascular diseases. Furthermore, we discuss miR regulation mechanism during in early development in vivo and invitro. Since many of the miR’s are precursors to transcriptional regulation, we relate back to their molecular control as we can then look together at the fundamental disease they might be exacerbating by this dysregulation.