The in vitro production and cryopreservation of mammalian embryos generate reactive oxygen species (ROS) due to conditions of the system that can overcome their antioxidant protection. Resveratrol is an antioxidant used in in vitro systems improving blastocyst rates, but its effect on antioxidant enzymes such as glutathione (GSH) in embryos produced by in vitro fertilization (IVF) after vitrification has not been reported. The objective of this study was to evaluate the effect of resveratrol in the in vitro maturation medium (IVM) of sheep oocytes (Ovis aries) on the levels of ROS and GSH in embryos produced by IVF subjected to vitrification. Resveratrol was added at 0µM, 0.25µM, 0.5µM and 1µM during oocyte in vitro maturation (IVM). Matured oocytes were fertilized with thawed ram sperm. Embryos were cultured in sequential media until blastocysts, then were vitrified for 24 h and after heating they were stained with DCFH-DA (2',7'-dichlorodihydrofluorescein diacetate) to determine the presence of ROS and with Cell Tracker Blue® for the presence of GSH. The quantitative values of ROS and GSH were obtained through the Image J image processor. The results showed that resveratrol increases GSH and decreases ROS production (p<0.05). It is concluded that its use in sheep oocytes during IVM has a beneficial effect on embryos produced by IVF subjected to vitrification, protecting them from oxidative damage by promoting the synthesis of antioxidants.

There are important challenges for modeling large electrical distribution circuits, even more with the presence of distributed renewable generation. Constructing simulations for assessing the effect of the penetration of distributed generation on electrical distribution networks has become of great importance for Distribution Network Operators (DNOs). This paper proposes a simulation strategy based on open-source platforms and the integration of scripting tools for the rapid modeling of large-scale electrical distribution circuits with distributed renewable generation. The implementation is based on the adaptation of a tool called QGIS2OpenDSS, which creates OpenDSS distribution network models directly from an open-source geographic information system, QGIS. The plugin’s capabilities are demonstrated using a real distribution feeder with more than 60% penetration of renewable generation based on photovoltaic systems. These simulations are carried out using real data from a circuit provided by a DNO in the Dominican Republic, which is used to demonstrate how this approach provides a more accessible and flexible way to simulate and assess the effect of Distributed Energy Resources (DERs) in Medium Voltage (MV) and Low Voltage (LV) networks, enabling utilities to evaluate system performance and identify potential issues.

The FTF (Fusarium Transcription Factor) gene family is composed of two members (FTF1 and FTF2) with high sequence homology. Both genes encode Zn(II)2Cys6 binuclear zinc finger transcription factors involved in the modulation of virulence in the F. oxysporum species complex (FOSC). While FTF1 is a multicopy gene exclusive of highly virulent strains of FOSC and is located in the accessory genome, FTF2 is a single copy gene, located in the core genome, and well conserved in all filamentous ascomycete fungi, except yeast. The involvement of FTF1 in the colonization of the vascular system and regulation of the expression of SIX effectors has been stablished. To address the role of FTF2 we generated and characterized null FTF2 mutants in a F. oxysporum f. sp. phaseoli weakly virulent strain and analyzed them together with the equivalent mutants formerly obtained in a highly virulent strain. The results obtained highlight a role for FTF2 as a negative regulator of the production of macroconidia and demonstrate that it is required for full virulence and positive regulation of SIX effectors. In addition, gene expression analyses provide compelling evidence that FTF2 is involved in the regulation of hydrophobins likely required for plant colonization.

This article analyses the environmental impact of the measures imposed during the SARS-CoV-2 pandemic. We compare the evolution of atmospheric pollution levels in recent years and during lockdown, and assess the effects of the decrease in mobility and changes in patterns and lifestyles during the latter period. Thus, the reduction in the risk to human health brought about by the improvement of air quality during the months of confinement through the use of dose-response functions is estimated. The focus of the case study is the island of Tenerife. The island of Tenerife has been selected because it can serve as an example for other sites in Europe. We distinguish between the three areas with the highest population concentrations: the Metropolitan, Southern, and Northern areas. The impacts of air pollution and its relationship with changes in consumption and activity patterns are clearly distinguishable. Therefore, the lessons learned can be easily extrapolated to other areas, in both island and mainland contexts.

Seeds can maintain their quality for a limited time; after that, they will lose their germination ability and vigor. Some physiological and physicochemical changes in the structure of the seeds during storage can decrease the quality of the seeds which is known as aging. Therefore, detection of the strong young seeds from the old ones is a vital issue in the modern agriculture. Conventional methods of detection of the seed viability and germination are destructive, time-consuming and costly. In this research, two peanut cultivars, namely North Carolina 2 (NC-2) and Florispan were selected and three artificial aging levels were induced to them. Hyperspectral images (HSI) of the samples were acquired and the seed viability was evaluated using two pre-trained convolutional neural network (CNN) image processing models, AlexNet and VGGNet. The noise of the reflection spectra of the samples was relatively resolved and modified by combining Preprocessing techniques of moving average (MA) and standard normal variate (SNV). Using principal component analysis (PCA), the dimensions were declined and three principal components (PC) were extracted. These PCs were then used as variables in the classification of support vector machine (SVM) and linear discriminant analysis (LDA). The results showed the high capability of CNN architectures such as AlexNet and VGGNet in detection of the seed viability based on the HIS with no pre-processing and feature extraction. The mentioned architectures reached the accuracy of 0.985 and 0.986, respectively. The combination of feature extraction method of PCA with LDA and SVM classifiers showed that the use of a limited number of PCs instead of all wavelengths can decrease the complexity of modeling, while enhancing the efficiency of the models such that LDA and SVM classifiers achieved the accuracy of 0.983 and 0.986 in classification of peanut sees, respectively.

Due to the irruption of new technologies in cities such as mobile applications, geographic infor-mation systems, Big Data, Internet of Things (IoT) or Artificial Intelligence (AI), new approaches to citizen management are being developed with the aim of adapting citizen services to this new en-vironment. These new services can enable city governments and businesses to offer their citizens a truly immersive experience that facilitates their day-to-day lives and ultimately improves their quality of life. In this sense, it is important to emphasize that all investments in infrastructure and technological developments in smart cities will be wasted if the citizens for whom they have been created eventually do not use them for whatever reason. To avoid these kinds of problems, the citizen's level of adaptation to the technologies should be evaluated. However, although much has been studied about new technological developments, studies to validate the actual impact and user acceptance of these technological models are much more limited. This paper tries to fill this gap presenting a new model of recommender system based in the most cited and used model in the scientific and academic literature: the Technology Acceptance Model (TAM) and using the most cited and agreed upon criteria in the existing literature. To accomplish the objective, this study in-troduces a novel recommender system that utilizes a fuzzy 2-tuple linguistic model in conjunction with the analytic hierarchy process (AHP) method to prioritize and personalize the relationship between tourists and smart cities. The methodology proposed in this paper was tested and validated in a case of study through different clusters to derive global recommendations tailored to each specific cluster. The main findings reveal that the use of technology is closely linked to the ability to enjoy personalized experiences in the realm of Smart Cities and Smart Tourism. As future works, authors recommend extending the recommender system model to any cluster of tourists using the proposed methodology and evaluate also other kind of disruptive technologies such as artificial intelligence (AI) in supporting the citizens.

Peanuts, owing to their composition of complex carbohydrates, plant protein, unsaturated fatty acids, and essential minerals (magnesium, iron, zinc, and potassium), hold significant potential as a vital component of the human diet. Additionally, their low water requirements and nitrogen fixation capacity make them an appropriate choice for cultivation in adverse environmental conditions. The germination ability of seeds profoundly impacts the final yield of the crop, assessing seed viability of extreme importance. Conventional methods for assessing seed viability and germination are both time-consuming and costly. To address these challenges, this study investigated Visible-Near Infrared Spectroscopy (Vis/NIR) in the wavelength range of 500-1030 nm as a non-destructive and rapid method to determine the viability of two varieties of peanut seeds: North Carolina-2 (NC-2) and Spanish flower (Florispan). The study subjected the seeds to three levels of artificial aging through heat treatment, involving incubation in a controlled environment at a relative humidity of 85% and a temperature of 50°C over 24-hour intervals. The absorbance spectra noise was significantly mitigated and corrected to a large extent by combining the Savitzky-Golay (SG) and Multiplicative Scatter Correction (MSC) methods. To identify the optimal wavelengths for seed viability assessment, a range of meta-heuristic algorithms were employed, including world competitive contest (WCC), league championship algorithm (LCA), Genetics (GA), Particle Swarm Optimization (PSO), Ant Colony Optimization (ACO), imperialist competitive algorithm (ICA), learning automata (LA), heat transfer optimization (HTS), forest optimization (FOA), discrete symbiotic organisms search (DSOS), and cuckoo optimization (CUK). These algorithms offer powerful optimization capabilities for effectively extracting relevant wavelength information from spectral data. Results revealed that all the algorithms demonstrated remarkable accuracy in predicting the allometric coefficient of seeds, achieving correlation coefficients exceeding 0.985 and errors below 0.0036, respectively. In terms of execution time, the ICA (2.3635 seconds) and LCA (44.9389 seconds) algorithms exhibited the most and least efficient performance, respectively. Conversely, the FOA and the LCA algorithms excelled in identifying the least number of optimal wavelengths (10 wavelengths). Subsequently, the seeds were classified based on the wavelengths selected by the FOA (10 wavelengths) and (DSOS (16 wavelengths) methods, in conjunction with logistic regression (LR), decision tree (DT), Multilayer Perceptron (MP), support vector machine (SVM), k-nearest neighbor (K-NN), and NaiveBayes (NB) classifiers. The DSOS-DT and FOA-MP methods demonstrated the highest accuracy, yielding values of 0.993 and 0.983, respectively. Conversely, the DSOS-LR and DSOS-KNN methods obtained the lowest accuracy, with values of 0.958 and 0.961, respectively. Overall, our findings demonstrated that Vis/NIR spectroscopy, coupled with variable selection algorithms and learning methods, presents a suitable and non-destructive approach for detecting seed viability.

Currently, the textile industry is a poorly automated sector, due in part to problems in the handling of deformable leather and textile parts during production operations. In this work, several problems in the handling process of leather and textile parts are addressed, introducing methods to increase the automation of the process. A pneumatic actuator designed to pick up textile or leather parts avoiding their deformation during transport has been developed. This actuator maximizes the number of gripping points to improve handling, making it more stable and efficient. Additionally, a vision system has been implemented in the part picking task which, in conjunction with the CAD information of the part, sends the modified gripping position of the part to the robot. This allows customized handling of each textile or leather part. Finally, validation tests have been carried out on this development, both in simulations and in laboratory conditions, demonstrating its viability and direct applicability in the production line.

The significant environmental issue of water pollution caused by emerging contaminants un-derscores the imperative for developing novel cleanup methods that are efficient, economically viable, and that are intended to operate at high capacity and under continuous flows at the in-dustrial scale. This study shows the results of the operational design to build a prototype for the retention at lab scale of pollutants residues in water by using as adsorbent material, insoluble polymers prepared by β-cyclodextrin and epichlorohydrin as a cross-linking agent. Laboratory in batch tests were run to find out the adsorbent performances against furosemide and hydro-chlorothiazide as pollutants model. The initial evaluation concerning the dosage of adsorbent, pH levels, agitation, and the concentration of pharmaceutical pollutants enabled us to identify the optimal conditions for conducting the subsequent experiments. The adsorption kinetic and the mechanisms involved were evaluated revealing that that the experimental data perfectly fit the pseudo second order model being the adsorption process mainly governed by chemisorption. According to the KF constants values of 0.044 (L/g) and 0.029 (L/g) for furosemide and hydro-chlorothiazide, respectively and determination coefficient (R2) higher than 0.9 for both com-pounds, Freundlich yielded the most favorable outcomes, suggesting that the adsorption process occurs on heterogeneous surfaces involving both chemisorption and physisorption processes. The maximum monolayer adsorption capacity (qmax) obtained by Langmuir isotherm reveal a saturation of the β-CDs-EPI polymer surface 1.45 times higher for furosemide (qmax = 1.282 mg/g) than hydrochlorothiazide (qmax = 0.844 mg/g). Based on these results, the sizing design and building of a lab scale model were conducted, which in turn will be used later to evaluate its performances working in continuous flow in a real scenario.

When we discuss migration and compare national trends, the topic most commonly centers on undocumented immigrants and asylum seekers. However, there is also considerable variation in internal migration patterns, with differences found between and within nations. Many factors shape whether, why, and where people relocate. Over the last few decades, the world's two largest economies - the United States and China - have seen domestic migration changes happening in opposite directions. China has become increasingly mobile and experienced urbanization. In contrast, the U.S. has seen a steady decline in the rate at which its population relocates, with cities experiencing net migration losses as citizens leave for suburbs. This paper examines these trends using data from the last decade to compare the two nations in areas of internal migration, urbanization, housing, social mobility, and economic growth.

This work implements a stable algorithm in Field-Programmable Gate Arrays (FPGAs) for which two architectures (unrolling the loop) were developed and analyzed. The algorithm recovers sources located at the boundary separating two homogeneous media that make up a two-dimensional non-homogeneous region from measurements on the boundary of such region. The problem of recovering these sources is an ill-posed inverse problem as small errors in the measurement can produce important changes in the source location. Inverse source problems have many applications in different areas, such as engineering and medicine, making the proposed implementation important. The first architecture (mode one) allows considering different operating speeds, which is an advantage depending on whether we work with fast or slow signals. The second one (mode two) reduces resource consumption by exploiting the characteristics of the source identification algorithm, which is an advantage for multichannel problems such as inverse electrocardiography or electroencephalography. The architectures were tested on four FPGAs of the 7 Series of Xilinx: Spartan-7 xc7s100fgga484, Virtex-7 xc7v585tffg1157, Kintex-7 xc7k70tfbg484, and Artix-7 xc7a35tcpg236. The two FPGA implementations of the algorithm were validated using synthetic examples implemented in MATLAB. The results presented here can be extended to concentric spheres and complex geometries.

: Background: Overweight and obesity are major risk factors for many chronic diseases, and weight-loss interventions often include systematic exercising and nutritional supplements. The purpose of this study was to determine the independent/synergistic effects of Spirulina maxima supplementation (6-week, 4.5 g/day) and a systematic physical exercise program (6 weeks/ 2 times) on body composition and cardiorespiratory fitness of overweight and obese subjects. Methods: 27 overweight and 25 obese sedentary male subjects were assigned to four interventions through a randomized double-blind, crossover controlled trial: Physical exercise program with (SE) or without (Ex) Spirulina maxima or no-exercise program with (Sm) and without (C) Spirulina maxima. Body composition and cardiorespiratory fitness parameters were taken during a maximal intensity test. Results: As compared to C group, SE, Sm and Ex groups reduced (p < 0.05) their body fat percentage while improving their maximal oxygen uptake (VO₂max; r = −0.40), being obese subjects more benefited. Weight loss, time to reach fatigue and onset of blood lactate accumulation were improved in both Spirulina maxima supplemented groups, regardless the subjects’ body composition. Conclusions: Spirulina maxima supplementation synergistically improves the effects of systematic exercise in body composition and cardiorespiratory fitness parameters in overweight but mostly in obese adults.

In this work, we report manganese phthalocyanine (MnPc) films obtained by ultrasonic spray-pyrolysis technique at 40°C deposited on glass substrate subjected to thermal annealing at 100 °C and 120°C. The MnPc films were characterized by UV/Vis spectroscopy, Raman spectroscopy, X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The absorption spectra of the MnPc films were studied in a wavelength range from 200 to 850 nm, where the characteristic bands of a metallic phthalocyanine known as B and Q bands were observed in this range of the spectrum. The optical energy band (Eg) was calculated by the Tauc equation. It was found that for these MnPc films, the Eg has the values of 4.41, 4.46 and 3.58 eV corresponding to as deposited, annealing 100°C and 120°C, respectively. The Raman spectra of the films showed their characteristic vibrational modes of the MnPc films. In X-ray diffractograms of these films, the characteristic diffraction peaks of a metallic phthalocyanine are observed, presenting a monoclinic phase. SEM images of these films were studied in cross section obtaining thicknesses of 2, 1.2 and 0.3 μm to as deposited, annealing 100°C and 120°C, successively. Also, in the SEM images of these films, both the average particle sizes ranging from 4 to 0.041 µm and the average diameter from 4.8 to 0.091 μm were obtained. The results agree with those reported in the literature for MnPc films deposited with other techniques.

In this Case Report we analyze the possible causes of the poor health status of a professional Apis mellifera iberiensis apiary located in Gajanejos (Guadalajara, Spain). Several factors that potentially favor colony collapse were identified, including Nosema ceranae infection, alone or in combination with other factors (eg, BQCV and DWV infection), and the accumulation of acaricides commonly used to control Varroa destructor in the beebread (coumaphos and tau-fluvalinate). Based on the levels of residues, the average toxic unit estimated for the apiary, suggests a possible increase in vulnerability to infection by N. ceranae due to the presence of high levels of acaricides. These data highlight the importance of evaluating these factors in future monitoring programs, as well as the need to adopt adequate preventive measures as part of national and international welfare programs aimed at guaranteeing the health and fitness of bees.

Considering nutritional qualities of gofio (Gf) and aloe vera juice (AVJ), their combination is indicated as an easy and fast source of ingest of basic bio elements. As the texture of the final product must be accepted by customers, the influence of Gf concentration on the rheological behavior of Gf/AVJ suspensions was determined. Shear thinning index of AVJ maintains unaltered despite the presence of Gf particles, although the viscosity value increases as expected. Linear viscoelastic studies on Gf/AVJ confirmed this is a viscoelastic liquid that changes from chewy to creamy texture with Gf concentration increase.

The interest in random fiber lasers (RFLs), first demonstrated one decade ago, is still growing and their basic characteristics have been studied by several authors. RFLs are open systems that present instabilities in the intensity fluctuations due to the energy exchange among their non-orthogonal quasi-modes. In this work, we present a review of the recent investigations on the output characteristics of a continuous-wave erbium-doped RFL, with emphasis on the statistical behavior of the emitted intensity fluctuations. A progression from the Gaussian to Lévy and back to the Gaussian statistical regime was observed by increasing the excitation laser power from below to above the RFL threshold. By analyzing the RFL output intensity fluctuations, the probability density function of emission intensities was determined, and its correspondence with the experimental results was identified, enabling a clear demonstration of the analogy between the RFL phenomenon and the spin-glass phase transition. A replica-symmetry-breaking phase above the RFL threshold was characterized and the glassy behavior of the emitted light was established. We also discuss perspectives for future investigations on RFL systems.

Taekwondo is a Korean martial art, combat sport, and Olympic discipline. Taekwondo competi-tion is characterized as an individual sport (1X1), single elimination tournament and repechage system. The aim goal of this study is brought of a bibliometric review regarding the item’s “taekwondo” and “performance”, through identified and published manuscripts on the Web of Science (WOS) database by December 31, 2022. The bibliometric analysis was used to analyze a data set of 460 WOS-indexed manuscripts published between 1992 and 2022. Descriptive analy-sis, citation, authorships, countries, institutionals, and keywords co-occurrence analyses were conducted into Taekwondo sports performance. The manuscripts founded in the WOS database are inserted on the categories: “Sports Science” (n = 229), “Hospitality Leisure Sport Tourism” (n = 48), and “Physiology” (n = 32). The authors Kazemi et al. (2006), Matsushigue et al. (2009), and Paillard (2017) are the must published and cited researchers. The countries with high number of published manuscripts with the objective of this study are Brazil (n = 83), South Korea (n = 57), and Spain (n = 52). We found also, five collaboration networks between authors and institutions, found a gap of the thematic relevant researchers. The authors should have highlighted Franchini, E., (n = 42), and Falco, C., (n = 20). It is recommended to carry out multidimensional research on Taekwondo sports performance with the aim of establishing collaborations within groups, insti-tutions, and countries. In this way, the productivity, effectiveness, and quality of research would be increased, as well as international collaboration networks.

The Bologna Process and the European Higher Education area require the application of new active methodologies in the classroom that place the student at the center of his or her learning process. In the present work we analyze the application of a Service-Learning methodology in the context of a Final Degree Dissertation (FDD) in the degree in Environmental Sciences at the University of Extremadura (Spain). The project deals with an isolated Kichwa community in Ecuador and involves the development of alternative science education materials for the capacitation of in-service science teachers. This paper evaluates how an FDD carried out according to self-learning (SL) principles can help in the acquisition of so-called soft skills and how these can be focused in the promotion of the Sustainable Development Goal (SDG) knowledge and achievement. To this end, a qualitative study of the experience and a deep evaluation, followed by a final reflection, were carried out. According to the preliminary results, we can conclude that Higher Education should include SDGs in its teaching praxis and could do this successfully using the SL methodology.

The aim of this study was to use latent profile analysis to identify specific profiles of burnout syndrome in combination with work engagement and to identify whether job satisfaction, psychological well-being, and other sociodemographic and work variables affect the probability of presenting a profile of burnout syndrome and low work enthusiasm. A total of 355 healthcare professionals completed the Spanish Burnout Inventory, the Utrecht Work Engagement Scale, the Job Satisfaction Scale, and the Psychological Well-Being Scale for Adults. Latent profile analysis identified 4 profiles: 1) burnout with high indolence (BwHIn); 2) burnout with low indolence (BwLIn); 3) high engagement, low burnout (HeLb); and 4) in the process of burning out (IPB). Multivariate logistic regression showed that a second job in a government health care institution; a shift other than the morning shift; being divorced, separated or widowed; and work load are predictors of burnout profiles with respect to the HeLb profile. These data are useful for designing intervention strategies according to the needs and characteristics of each type of burnout profile.

Owing to the escalating adoption of IoT systems across various domains, the demand for mobile and wireless power sources has surged. Although conventional batteries typically serve as energy storage components, the current low-power consumption devices necessitate eco-friendly alterna-tives. In this study, we designed, fabricated, and characterized an energy harvesting device that repurposes mechanical vibrations. A three-beam design was employed to harvest energy across a broader range of potential frequencies. Finite element models were simulated to ascertain the first bending moment for both sets of beams. A nanostructured piezoelectric multilayer film made of ZnO was deposited onto an AISI 304 steel substrate, and a photosensitive resin seismic mass was implemented. Low-cost techniques generating minimal environmental waste were leveraged in the fabrication process. The piezoelectric film was deposited using a spray nebulization technique involving recycled materials and cost-effective equipment. Micrographs of the layers unveiled the presence of nanospheres with diameters of 250 nm. Employing a custom-made shaker, output voltages of 1.08 V and 180 mV, and power outputs of 1.849 µW and 16.2 nW were achieved for each set of beams. The electrical characterization was conducted using a custom-made shaker, repurposing materials for this objective.

RNA polymerase II (RNAPII) frequently transcribes non-protein coding DNA sequences in eukaryotic genomes into long non-coding RNA (lncRNA). Here, we focus on the impact of the act of lncRNA transcription on nearby functional DNA units. Distinct molecular mechanisms linked to the position of lncRNA relative to the coding gene illustrate how non-coding transcription controls gene expression. We review the biological significance of the act of lncRNA transcription on DNA processing, highlighting common themes, such as mediating cellular responses to environmental changes. This review presents the background in chromatin signaling to appreciate examples in different organisms where we can interpret functions of non-coding DNA through the act of RNAPII transcription.

The objective of this research was to study the dynamics of moisture and nutrition at the root zone and to quantify the variables linked to efficient water management in avocado orchards of mid and high-lands of Michoacán, México, in typical Andisols of low fertility with (A)C(w2) and C(w2) climates, respectively. Using the FDR (Frequency Domain Reflectometry) technology, the dynamics of soil moisture and salinity were recorded daily at four depths: 0-15, 15-30, 30-45, and 45-60 cm. The soil moisture balance model was used to determine actual evapotranspiration (ETr), crop coefficient (Kc), and water use efficiency (WUE). Results indicated that ETr is 66-73% of the total water at 0-30 cm depth; the fertilizer absorption is limited to 0-30 cm, being negligible at deeper layers. The water use efficiency is 4.4 to 5.6 kg of fruit m-3 of applied water, and the ratio of the water use index (ETr/irrigation sheet applied, ISA) is 0.65-0.70; while the annual avocado Kc is 0.72 in Cutzato and 0.78 in Tiamba. We concluded that avocado has a low water requirement, it does not cause leaching of nutrients and/or water, the absorption of water and nutrients mostly occurs at 30 cm depth, and from a hydrological point of view, the crop is environmentally friendly.

Structural hydroxide groups in layered magnesium-aluminum double hydroxides were partially replaced by fluoride ions. Fluorinated and fluorine-free materials were used as hosts for two dyes, carminic acid and hydroxyl naphthol blue, resulting in a hybrid pigment color palette. Additionally, the pigments were protected with a magnesium hydroxide phase to prevent the color from fading over time. The color properties of the pigments were significantly influenced by the host of dye, since the presence of fluorine directly influences the acid-base properties of the layered double hydroxides. Finally, the pigments were successfully applied to prepare colored creams.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Background Cesarean scar ectopic pregnancies are a rare form of extrauterine pregnancies, yet their incidence has increased along with the rise in the number of cesarean deliveries. As with other ectopic pregnancies, cesarean scar ectopic pregnancies pose a greater risk for maternal hemorrhage and ultimately maternal mortality. Case presentation We present a series of clinical cases of cesarean scar ectopic pregnancy diagnosed by transvaginal ultrasonography. Each patient received an individualized treatment: the rate of success depended on the particular maternal condition in each case. Due to the low frequency of this entity, there are no clear protocols for its treatment and thus there are numerous options for treatment and follow up: expectant management, medical therapy, surgical intervention, uterine artery embolization or a combined approach. Each method has different levels of success and is dependent on the surgeon’s skill and patient presentation. The transvaginal ultrasound is necessary to obtain the fine details of the gestation sac and its relation to the scar and must be followed by a meticulous abdominal scan with a full bladder. Conclusion Herein, we present a rare pathological phenomenon whose frequency is on the rise, and for which transvaginal ultrasound and flow doppler provide high diagnostic accuracy. Early diagnosis of cesarean scar ectopic pregnancies offers treatment options to that may help avoid uterine rupture and bleeding, thus preserving the uterus and future fertility.

Identifying groups that share common features among datasets through clustering analysis is a typical problem in many fields of science, particularly in post-omics and systems biology research. In respect of this, quantifying how a measure can cluster or organize intrinsic groups is important since currently there is no statistical evaluation of how ordered is, or how much noise is embedded in the resulting clustered vector. Many of the literature focuses on how well the clustering algorithm orders the data, with several measures regarding external and internal statistical measures; but none measure has been developed to statistically quantify the noise in an arranged vector posterior a clustering algorithm, i.e., how much of the clustering is due to randomness. Here, we present a quantitative methodology, based on autocorrelation, to assess this problem.

The paper proposes a novel methodology for the stabilization of shallow foundations, with a simplified model combined with 3D Electrical resistivity tomography (ERT-3D) and conso- lidation injections. To determine its usefulness, the method has been applied in a case located in Estepona (southern Spain). The chosen tomography model is the dipole-dipole configuration, with an optimized distance between electrodes of 0.80 m for a better visualization of the foundation subsoil; with this parameterization, a total of 72 electrodes were installed in the analyzed case. In this work, the depth of the anomaly in the building's supporting subsoil was detected ranging from 2.00 m to 3.90 m deep. The study also delineates areas of high resistivity variations (50-1,000 Ω m) in the middle and eastern end of the field. These data have been validated and corroborated with a field campaign. The results of the ERT-3D monitoring are presented, once the investment data has been processed with the RES3DINV software, from the beginning to the end of the stabilization intervention. The novelty occurs with the interaction between the tomography and the foundation consolidation injections, until the final stabilization; very useful methodology in case of emergency consolidation, where there is a need to minimize damage to the building. Thus, people using this combined system; will be able to practically solve the initial anomalies of the subsoil that caused the damages, in a non-invasive way, considerably lowering the value of the resistivities.

This article aims to serve as a guide for the construction of supply chain simulation models designed with a lean approach, using Promodel software. To achieve this, a supply chain was designed for a fictitious company located in the City of Celaya, Guanajuato and a set of suppliers located in different cities within the same State. It was used as a google tool to define the distances between each of the companies. As a final result, a representative model of a supply chain was obtained, as well as a methodology that allows the construction of lean supply chains regardless of the number of companies that comprise it. The effect of the variability in the delivery times between suppliers was incorporated into the simulation model, as well as an equation that calculates the pollution emissions of the vehicles that integrate the network that moves the products between the companies. With this work it is possible to represent networks of supply chains of real world companies, where the variability and contamination factor is included, to facilitate the decision making regarding the number of vehicles, inventory levels, quantities to be shipped, frequency in the shipments, etc. with the purpose of contaminating as little as possible and at the same time preventing interruptions in the supply chain using the least amount of resources possible.

Over the last decade, Psidium guajava L. (guava) leaves have demonstrated their in vitro and in vivo effect against Diabetes mellitus (DM). However, there is a lack of literature concerning the effect of the individual phenolic compounds present in the leaves in DM disease. For this reason, the aim of the present work was the in silico evaluation of each phenolic compound. The identification of an 80% ethanol extract of guava leaves revealed the presence of 73 compounds. The in silico study carried out with the DIA-DB web server revealed that aldose reductase was the target protein with heterogeneous affinity. Naringenin exhibited the highest number of interactions with target proteins, and compounds like catechin, quercetin, naringenin and morin displayed similarities with known antidiabetic drugs. In conclusion, the computational workflow showed that guava leaves contain several compounds that can play a therapeutic role in the treatment of DM.

The knowledge of the precise anatomy and dimensions of the pulp chamber in the different teeth allows the odontologist to perform correct diagnosis, as well as treatment planning and moni-toring. The clinical practice has introduced cone-beam computed tomography (CB-CT) as a method to evaluate the morphology and dimensions of the pulp chamber. Nevertheless, micro-computed tomography (micro-CT) is regarded as the gold standard in approaching those topics. Here we have designed an algorithm that takes as input DICOM images from in vivo CB-CT of permanent molars to determine the accuracy CB-CT for evaluation of pulp chamber volume. The values were compared with those from in vivo CB-CT (rough and expert manipulated) and ex vivo micro-CT. The relative errors obtained with the volume calculated by the algorithm vs. the volume measured by micro-CT do not exceed 5.7%; also, no significant differences were found between algorithm volumes vs. manipulated CB-CT volumes while all volumes were different from those obtained with automatic CB-CT software. These data demonstrate that volume algorithm CB-CT based may be a reliable technique for evaluation of the pulp chamber volume in permanent molars and can be useful in the diagnosis of pulp diseases, as well as in the planning and monitoring of their treatments.

Combining antiviral drugs with different mechanisms of action can help prevent the development of resistance by attacking the infectious agent through multiple pathways. Additionally, by using faster and more economical screening methods, effective synergistic drug candidates can be rapidly identified, facilitating faster paths to clinical testing. In this work, a rapid method was standardized to identify possible synergisms from drug combinations. We analyzed the possible reduction of antiviral effective concentration of drugs already approved by the FDA, such as ivermectin  (IVM), ribavirin (RIBA) and acyclovir (ACV) against Zika virus (ZIKV), Chikungunya virus (CHIKV) and herpes virus type 2 (HHV-2). Essential oils (EOs) were also included in the study since they have been reported for more than a couple of decades to have broad-spectrum antiviral activity. We also continued studying the antiviral properties of one of our patented molecule with broad-spectrum antiviral activity, the ferruginol analogue 18-(phthalimid-2-yl)ferruginol (phthFGL). In general, the combination of IVM, phthFGL and Oregano EO showed the greatest synergism potential against CHIKV, ZIKV and HHV-2, obtaining a reduction in the EC99 value of up to ~8, and ~27, and ~12-fold for CHIKV, in example, respectively. The ternary combination RIBA, phthFGL, Oregano EO was slightly more efficient than the binary combination RIBA/phthFGL but much less efficient than IVM, phthFGL, Oregano EO which indicates that IVM could contribute more to the differentiations of cell targets (for example by inhibition of host heterodimeric importin IMP α/β1 complex) than ribavirin. PhthFGL showed a good pharmacokinetic profile.

Pencil-beam Doppler scatterometers are a promising remote sensing tool for measuring ocean vector winds and currents from space. While several point designs exist in the literature, these designs have been constrained by the hardware they inherited, and the design is sub-optimal. Here, I present guidelines to optimize the design of these instruments starting from the basic sensitivity equations. Unlike conventional scatterometers or pencil-beam imagers, appropriate sampling of the Doppler spectrum and optimizing the radial velocity error lead naturally to a design that incorporates a pulse-to-pulse separation and pulse length that vary with scan angle. Including this variation can improve radial velocity performance significantly and the optimal selection of system timing and bandwidth is derived. Following this, optimization of the performance based on frequency, incidence angle, antenna length, and spatial sampling strategy are considered. It is shown that antenna length influences the performance most strongly, while the errors depend only on the square root of the transmit transmit power. Finally, a set of example designs and associated performance are presented.

The progressive impairment analysis in gait from neurological diseases patients such as Hereditary Ataxias (HA) has been carried out using gait data collected with movement sensors. This research is focused on finding the minimum amount required of gait features to recognize efficiently and less intrusive way, HA patients based on data collected with iPhone movement sensors placed on the ankles from 14 HA patients and 14 healthy people. A twofold proposal is made , first a local minimum prominent peak criterion to find out the starting point of each stride, to get 10-stride window about which 56 spatial-temporal features are derived; second a search strategy based on Hill Climbing algorithm to reduce the number of gait features and sensors. The main results were the findings that with two gait patterns a 96% of classification accuracy was achieved by using K-Nearest Neighbors (KNN) and Multi-Layer Perceptron (MLP) algorithms, but in addition, MLP only right ankle sensor patterns were required which also allows to reduce the intrusion.

Chiral hydroxamic acid (HA) and bis-hydroxamic acid (BHA) ligands have made significant contributions to the field of asymmetric synthesis, particularly in the synthesis of natural products. These ligands possess unique molecular structures that allow for exceptional stereochemical control, leading to their widespread use in catalytic systems. This review highlights the advancements made in asymmetric synthesis using chiral hydroxamic acid and bis-hydroxamic acid ligands and their impact on the synthesis of complex natural products. The discussion encompasses their role in enantioselective C-C bond formation, the functionalization of C-H bonds, asymmetric transformations involving heteroatoms, and their application in the total synthesis of natural products. The versatility and efficiency of chiral hydroxamic acid ligands and bis-hydroxamic acid ligands make them invaluable tools for synthetic chemists working towards the efficient and selective synthesis of natural products. This review provides a comprehensive overview of their contributions, showcasing their potential to expand the boundaries of chemical synthesis and access the diverse array of natural product scaffolds.

Right atrial isomerism (RAI) is a complex entity whose treatment and outcome are heterogeneous. The aim of this study was to analyze the results obtained after cardiac surgery in patients with RAI. A retrospective study was conducted; it included patients diagnosed with RAI who underwent cardiac surgery; their follow-up was from January 1, 2010 to March 31, 2020. Demographic characteristics and perioperative conditions were described. Thirty-eight patients with RAI were included, the median age was 4 years (IQR 2-9.2), and 57.9% were men. The main diagnoses were atrioventricular canal (63.2%) and pulmonary stenosis (55.3%). The most common surgical procedures were modified Blalock‐Taussig shunt (65.8%) and total cavopulmonary connection with an extracardiac conduit fenestrated without cardiopulmonary bypass (15.9%). The use of inhaled nitric oxide was a marker of postoperative mortality in critically ill patients (OR: 10.33; 95% CI: 1.04 - 102.08; p = 0.02). The overall survival was 86.8%, with a better outcome in those who did not require reintubation (Log Rank, p < 0.01). The survival of RAI was similar to other centers of reference. Individuals with RAI should be evaluated rigorously to determine an adequate repair strategy, considering high morbidity and mortality.

Microbial biofilms cause several environmental and industrial issues, even on the human health. Although they have represented a threaten due to their resistance to antibiotics, there are currently no approved antibiofilm agents for clinical treatments. The multi-functionality of antimicrobial peptides (AMPs) including the antibiofilm activity and their potentialities to target multiple mi-crobes motivated the synthesis of AMP relatives for developing antibiofilm agents for clinical purposes. Antibiofilm peptides (ABFPs) have been organized in databases that allowed the building of prediction tools which have assisted in the discovery/design of new antibiofilm agents. However, the complex network approach has been explored yet as an assistant tool for this aim. Herein, a kind of similarity networks, called the Half-Space Proximal Network (HSPN) is applied to represent/analyse the chemical space of the ABFPs aimed to identify promising scaf-folds for the development of next generation antimicrobials, able to target both planktonic and biofilm microbial forms. Such analyses also considered the metadata associated to the ABFPs such as origin, other activities, targets, etc. in which the relationships were projected by multilayer networks called metadata networks (METNs). From the complex networks mining, a reduced but informative set of 66 ABFPs representing the original antibiofilm space was extracted. This subset retained from the most central to atypical ABFPs, having some of them, desired properties for developing next generation antimicrobials. So, this subset is advisable for assisting the search/design both new antibiofilm/antimicrobial agents. The provided ABFP motifs list, dis-covered within the HSPN communities, is also useful for the same purpose.

In this paper, an iterative procedure to find the solution of a nonlinear structural model is introduced. The model presents different multiplicities where parameters are randomly selected within a solvability region. To achieve this aim, a class of multipoint fixed-point iterative schemes for single roots is modified to find multiple roots, reaching the fourth order of convergence. Complex discrete dynamics techniques are employed to select the members with the most stable performance. The structural problem, as well as some academic problems involving multiple roots, are solved numerically to verify the theoretical analysis, robustness and applicability of the proposed scheme.

The acquired immunodeficiency syndrome (AIDS) caused by the human immunodeficiency virus (HIV) continues to be a public health problem. In 2020, 680,000 people died from HIV-related causes, and 1.5 million people were infected. Antiretrovirals are only a way to control HIV infection but not to cure AIDS. As such, effective treatment must be developed to control AIDS. Developing a drug is not an easy task, and there is an enormous amount of work and economic resources invested. For this reason, it is highly convenient to employ computer-aided drug design methods, which can help generate and identify novel molecules. Using the de novo design, new novel molecules can be developed using fragments as building blocks. In this work, we develop a virtual-focused compound library of HIV-1 viral protease inhibitors from natural product fragments. Natural products are characterized by a large diversity of functional groups, many sp3 atoms, and chiral centers. Pseudo-natural products are a combination of natural products fragments that keep the desired structural characteristics from different natural products. An interactive version of chemical space visualization of virtual compounds focused on HIV-1 viral protease inhibitors from natural product fragments is freely available at https://figshare.com/s/ceb58d58e8f5585ce67e.

The Atlantic puffin is a medium-sized seabird with black and white plumage and orange feet. It is distributed mainly along the northern Atlantic Ocean and due, among other reasons, to human activities, it is in a threatened situation and classified as a vulnerable species according to the International Union of Conservation of Nature (IUCN). In this study, we used a total of 20 carcasses of juvenile Atlantic puffins to perform anatomical cross sections and magnetic resonance images. Thus, an adequate description of the head was made, providing valuable information that could be helpful as a diagnostic tool for veterinary clinicians, who increasingly treat these birds in zoos, rehabilitation centers and even in the wild.

In Mexico there is a deficit in the production of pine resin, because it depends on natural forests. Therefore, it is necessary to select provenances and phenotypes of potential species such as P. oocarpa. The objective was to determine the difference between provenances and the variation of resin components and quality, as well as the effect of geographic and climatic factors. Resin from five provenances was collected from southern Mexico. The percentage of rosin, turpentine and water was obtained, as well as the acidity and saponification index. P. oocarpa resin had 80.94 % rosin, 7.7 % turpentine and 11.49 % water. The saponification and acidity index was 125.47 and 117.49 mg KOH.g_1, respectively. All variables showed differences (p≤ 0.0001) between provenances. The provenance contributed between 6.44 and 11.71 % to the total variance, the error contributed between 88.29 and 93.56 %. Geographic and climatic variables only had an effect on the percentage of turpentine; the correlation was negative with altitude and longitude, but positive with temperature and precipitation. The results allow defining seed collection sites for resin plantations and orienting the selection for a P. oocarpa improvement program.

This paper investigates the mental health stressors experienced by Central American youth immigrants and asylum seekers, including unaccompanied minors, surveyed in the U.S. in 2017. This population is hard to reach, vulnerable, and disproportionately exposed to trauma from a young age. They face numerous challenges to mental health, and increased psychopathological risk, exacerbated by high levels of violence and low state-capacity in sending countries, restrictive immigration policies, the fear of deportation for themselves and their family members, and the pressure to integrate once in the U.S. Using survey data and the validated PHQ-9 questionnaire and Child PTSD Symptom Scale (CPSS), we find that Central American youth have seen improvements in their self-reported mental health after migrating to the U.S. but remain at risk of further trauma exposure, depression, and PTSD. They exhibit a disproportionate likelihood of having lived through traumatizing experiences that put Central American immigrants at higher risk for psychological distress and disorders and may also create obstacles to integration that in turn create new stressors that compound with PTSD and depression. PTSD, depression, or anxiety can be minimized through programs that aid their integration and mental health.

Nutrient estimation in forest ecosystems through satellite images allows us to obtain accurate data, starting with data transformation from forest stands and the existing relationship with the spectral information of the image through modeling. The objective of the study was to quantify and validate the content of C, N, H in aboveground tree biomass in managed stands using spatial modeling and satellite images. This study was conducted during 2017-2018 in managed forest stands in San Juan Lachao, Oaxaca, Mexico. Fifteen 400 m2 experimental sites were selectively established, using a completely randomized experimental design of five silvicultural treatments with three replications. As part of data preprocessing, normality and homogeneity of variances assumptions were checked using the Shapiro-Wilk and Bartlett tests, respectively. From the pixels, data of the average of Normalized Difference Vegetation Index (NDVI) that surrounded the sampling sites were contrasted against the data obtained from forest inventory and the regression models to estimate C, N, H and biomass were generated. Models were validated by NDVI. With the models we estimated 0.95 t ha-1 biomass, which contains between 0.61 and 0.63 of C, 0.44-0.46 of N and 0.24 of H. The models generated had coefficients of determination (R2) of 0.85 to 0.87, which are significant parameters (p ≤ 0.0001). These results confirm that the use of Sentinel satellite images in the estimation of these elements in forest ecosystems based on the relationship between data inventory and the NDVI is highly reliable.

The aim of this review is to present the Quality by Design (QbD) model as a suitable methodology to perform research in the academic Costa Rican institutions that teach Pharmacy. Pubmed, Science Direct, and Google Scholar databases were screened for original and review papers, as well as short communications published not more than 10 years ago. Publications were screened by title and abstract. Relevant references were used to develop three important themes: The University’s Research Model in Costa Rica, QbD Model, and QbD as a Research Methodology for Industrial Pharmacy in the Academy. In this sense, the QbD model is a great methodology for carrying out research projects regarding Pharmaceutical Sciences but especially for Drug Development. Academic research based on this model enables training and developing practical, scientific, and leadership skills in pharmacy students. The generated knowledge can be shared in the classrooms, which represents an ideal environment to communicate their research results and to foster collaborative work between researchers, professors, and students. The participation of all these actors allows a high level of commitment to research work, which benefits the scientific advancement of the university and society. It is important to visualize the student body as potential key actors in the research process, encouraging in them the desire to become trained scientific researchers who want to pursue a career in the academy, giving continuity to it.

The present work shows a novel physical-mathematical model to estimate the average corrosion resistance index from the crystallographic texture in API 5L steels. The crystallographic texture of the studied steels was measured by means of the X-ray diffraction technique. The model, based on the symmetric spherical surface harmonics for a BCC structure, is capable of describing the anisotropy surface of anodic dissolution resistance of the crystal and establishing a straightforward relationship between crystallographic texture, surface roughness, and metal corrosion behavior. The predictions of the average corrosion resistance index made from the crystallographic texture were in good agreement with those obtained from potentiodynamic polarization curves for the investigated steels. This agreement validates the capacity of this model and opens the possibility of applying it as a novel criterion for the material selection and design stages in order to combat metal corrosion problems.

This research undertakes a quantitative exploration of the impact of procurement mo-dalities on economic efficiency and inclusive procurement within the Dominican Repub-lic's public sector. Applying data science methodologies and machine learning techniques, this study analyzes a rich dataset of public procurement contracts spanning from 2018 to 2023. A focus is placed on understanding how different procurement modalities affect contract amounts and processing times—two key indicators of economic efficiency. Machine learning models, including Random Forest and Gradient Boosting, are em-ployed to predict these essential metrics across different procurement modalities. The findings indicate a significant positive correlation between certain procurement modali-ties and economic efficiency. The machine learning models reveal that procurement strategies focused on local sourcing and transparent bidding processes tend to yield high-er economic returns and more equitable outcomes. This research underscores the poten-tial of quantitative analysis to inform procurement policies, fostering a more economi-cally efficient and inclusive procurement ecosystem in the Dominican Republic's public sector. The insights garnered from this study could have significant implications for the design of more inclusive procurement strategies, contributing to socio-economic growth and corruption reduction in the Dominican Republic.

In this paper, we present a three-step sixth-order iterative schemes to estimate the solutions of a nonlinear systems of equations, for predicting the shear strength of a reinforced concrete beam. This procedure is designed by means of a weight function technique. The values for the parameters of this system were randomly selected inside the prescribed ranges by technical standards for structural concrete; moreover, some of this parameters were fixed taking into consideration the solvability region of the adopted steel constitutive model. The efficiency of the new class is compared with other current schemes, with very good results.

The Sunyaev-Zeldovich effect (SZe) is a global distortion of Cosmic Microwave Bckground (CMB) spectrum as result of its interaction with a hot electron plasma in the intracluster medium for large gravitational virialized structures such as galaxy clusters. Furthermore, this hot gas of electrons emits X-Rays due to its fall in the gravitational potential well of the cluster. The analysis of SZe and X-Ray data, provide a method for calculating distances to galaxy clusters at any redshift (Angular diameter distance (d_A) and gas mass fraction (f_gas)). On the other side, many of these galaxy clusters produce a Strong Gravitational Lens effect (SGL), which has become an useful astrophysical tool for cosmology. We use these cosmological tests, in addition to the more traditional ones (SNIa, CMB, BAO), to constraint alternative models of dark energy (ωCDM, CPL, IDE, EDE) and study the history of expansion through the cosmographic parameters (H(z), q(z), j(z)). Using Akaike and Bayesian Information Criterion (AIC, BIC) we find that the ωCDM and ΛCDM models are the most favored by the observational data. In addition, we found that at low redshift appears an peculiar behavior of slowdown of aceleration, which occurs only on dynamical dark energy models using only galaxy clusters (d_A,clusters + f_gas).

La integration (at various nominal contents) in SBA-15 prepared under acidic medium was intended from corresponding direct nitrate addition during mesoporous silica formation. Materials were impregnated with Pt (1.5 w%) and studied through several textural (N2 physisorption), structural (XRD, TG-DTG) and surface (FTIR, STEM-HAADF, SEM-EDS, NH3 and CO2 TPD) instrumental techniques. Pt-impregnated solids were tested in phenol hydrodeoxygenation (HDO, T=250 °C, 3.2 MPa, batch reactor, n-decane as solvent). Catalytic activity (in pseudo first order kinetic constant, kHDO basis) was related to Pt dispersion which was, however, not determined by nominal rare earth content. Determining actual composition of modified SBA-15 materials is crucial in reaching sound conclusions regarding their physicochemical properties, especially when La modifier is directly added during mesoporous matrices formation where efficient interaction among constituents could be difficult to get. Otherwise, results from some characterization techniques (N2 physisorption and FTIR, for instance) could be misleading and even contradictory. Indeed, extant modifier precursors when under SBA-15 synthesis conditions could affect the properties of prepared materials even though they were absent in obtained| formulations. Performing a simple compositional analysis could eliminate uncertainties regarding the role of various modifiers on characteristics of final catalysts. However, several groups have failed in doing so.

As the rate of discovery of new antibacterial compounds towards multidrug resistant bacteria is declining, there is an urge for the search of molecules that could revert this tendency. Acinetobacter baumannii has emerged as a highly virulent Gram-negative bacterium that has acquired multiple mechanisms against antibiotics and is considered of critical priority. In this work we developed a quantitative structure-property relationship (QSPR) model with 592 compounds for the identification of structural parameters related to their property as antibacterial agents against A. baumannii. QSPR mathematical validation (R2 = 70.27, RN = -0.008, aR2 = 0.014 and δK = 0.021) and its prediction ability (Q2LMO= 67.89, Q2EXT = 67.75, a(Q2)= -0.068, δQ = 0.0, rm2 = 0.229, and ∆rm2 = 0.522) were obtained with different statistical parameters; additional validation jobs were done using three sets of external molecules (R2 = 72.89, 71.64 and 71.56). We used the QSPR model to perform a virtual screening on the BIOFACQUIM natural product database. From this screening our model showed that molecules 32 to 35 and 54 to 68, isolated from different extracts of plants of the Ipomoea sp., are potential antibacterial against A. baumannii. Furthermore, biological assays showed that molecules 56 and 60 to 64 have a wide antibacterial activity against clinical isolated strains of A. baumannii, as well as other multidrug resistant bacteria including Staphylococcus aureus, Escherichia coli, Klebsiella pneumonia, and Pseudomonas aeruginosa. Finally, we propose 60 as a potential lead compound due to its broad-spectrum activity and its structural simplicity. Therefore, our QSPR model can be used as a tool for the investigation and search of new antibacterial compounds against A. baumannii.

Polyvinyl alcohol (PVA) is highly compatible polymer with biological environments. Specifically, it has been used as a trap for different types of microorganisms in Bio-MEMS, and its properties can be modified to act as an electrode for electrochemical analysis. This study presents a nano-composite developed with PVA, multiwall carbon nanotubes (CNTs) doped with nitrogen, which changes the electrical properties of the polymer and its viscosity to obtain nanofibers by electro-spinning. The proposed nanocomposite was characterized using Fourier transform-infrared and Raman spectroscopy techniques, confirming the presence of the CNTs immersed in the polymer. High-resolution transmission electron microscopy was used to obtain the micrographs that showed the characteristic interplanar distances of the multiwall CNT in the polymeric matrix with values of 3.63 Å. Finally, the CNx mats were exposed to various aqueous solutions in a po-tentiostat to demonstrate the effectiveness of the nanofibers for electrochemical analysis. The CNx-induced changes in the electrical properties of the polymer were identified using cyclic voltammograms, while the electrochemical analysis revealed supercapacitor behavior.

There is a relationship between systemic sarcoidosis (SS) and malignancy. Sarcoidosis results from an exaggerated immune response in genetically susceptible individuals. In oncologic pa-tients with sarcoidosis, tumoral antigens and antineoplastic treatment are considered potential triggering factors. The observation of a patient with granulomas in a parotid carcinoma that later developed SS led us to review previous tumors of patients with SS. The aim of the study is to see if granulomas were already present in the tumors that preceded sarcoidosis. We identified 196 sarcoidosis patients, 47 of which had a previous tumor. We were able to review 29 cases 12 of which showed tumor associated granulomas (TAGs)(41.4%). This ratio is much higher than that of the normal population. We analyzed five control patients without sarcoidosis for each tumor. In conclusion, we have observed TAGs in patients who later develop SS. In our series, the ratio of TAGs in patients with SS was significantly greater than in the normal population. To prove our findings, we suggest reviewing the history of patients with SS in search of previous tumors. The histology of such tumors should be reviewed in an attempt to identify granulomas.

(1) Background: Franco’s dictatorship was an authoritarian regime in Europe in the twentieth century. The political and historical context has a significant influence on the socio-cultural make-up of each era, having consequences on equality and violence against women. The objec-tive of our study is to explore and understand women’s experiences of violence against women during the Franco regime and how it affects them today; (2) Methods: This qualitative study ex-plores violence against women in Francoist Spain. Data was colleted between January and march 2022 through twenty-one interviews were carried out with female survivors of Francoism; (3) Results: Three themes emerged from the analysis: underlying social conditions that allow for vio-lence against women; forms of violence against women: from punishment to forced silence; dif-ferent standpoints about violence against women: the feminist struggle versus denial; (4) Conclu-sions: We concluded that the imposed patriarchy during Francoist repression was harmful for Spanish women for decades. Women suffered violence against women and they are still bearing the consequences, passing on attitudes that could contribute to the persistence of violence against women.

Chronic myeloid leukaemia (CML) is a haematological neoplasm driven by the BCR/ABL fusion oncogene. The monogenic aspect of the disease and the feasibility of ex vivo therapies in haematological disorders make CML an excellent candidate for gene therapy strategies. The ability to abolish any coding sequence by CRISPR-Cas9 nucleases offers a powerful therapeutic opportunity to CML patients. However, a definitive cure can only be achieved when only CRISPR-edited cells are selected. A gene-trapping approach combined with CRISPR technology would be an ideal approach to ensure this. Here, we have developed a CRISPR-Trap strategy that efficiently inserts a donor gene trap (SA-CMV-Venus) cassette into the BCR-ABL1-specific fusion point in the CML K562 human cell line. The trapping cassette interrupts the on-cogene coding sequence and expresses a reporter gene that enables the selection of edited cells. Quantitative expression analyses showed significantly higher level of expression of the BCR-Venus allele coupled with a drastically lower level of BCR/ABL expression in Venus+ cell fractions. Functional in vitro experiments showed cell proliferation arrest and apoptosis in selected Venus+ cells. Finally, xenograft experiments with the selected Venus+ cells showed a large reduction in tumour growth, thereby demonstrating a therapeutic benefit in vivo. This study is a proof of concept for the therapeutic potential of a CRISPR-Trap system as a novel strategy for gene elimination in haematological neoplasms.

We propose an advanced filtering scheme based on Recurrent Neural Networks (RNNs) and Deep Learning to enable efficient control strategies for Vertical Farming (VF) applications.  We demonstrate that the best RNN model incorporates five neuron layers, with the first and second containing ninety Long Short-Term Memory neurons.  The third layer implements one Gated Recurrent Units neuron.  The fourth segment incorporates one RNN network, while the output layer is designed by using a single neuron exhibiting a rectified linear activation function.  By utilizing this RNN digital filter, we introduce two variations: (1) A scaled RNN model to tune the filter to the signal of interest, and (2) A moving average filter to eliminate harmonic oscillations of the output waveforms. The RNN models are contrasted with conventional digital Butterworth, Chebyshev I, Chebyshev II, and Elliptic Infinite Impulse Response (IIR) configurations.  The RNN digital filtering schemes avoid introducing unwanted oscillations, which makes them more suitable for VF than their IIR counterparts.  Finally, by utilizing the advanced features of scaling of the RNN model, we demonstrate that the RNN digital filter can be pH selective, as opposed to conventional IIR filters.

CVDs are a leading cause of death globally. In CVDs, the heart is unable to deliver enough blood to other body regions. Since effective and accurate diagnosis of CVDs is essential for CVD prevention and treatment, machine learning (ML) techniques can be effectively and reliably used to discern patients suffering from a CVD from those who do not suffer from any heart condition. Namely, machine learning algorithms (MLAs) play a key role in the diagnosis of CVDs through predictive models that allow us to identify the main risks factors influencing CVD development. In this study, we analyze the performance of ten MLAs on two datasets for CVD prediction and two for CVD diagnosis. Algorithm performance is analyzed on top-two and top-four dataset attributes/features with respect to five performance metrics –accuracy, precision, recall, f1-score, and roc-auc – using the train-test split technique and k-fold cross-validation. Our study identifies the top two and four attributes from each CVD diagnosis/prediction dataset. As our main findings, the ten MLAs exhibited appropriate diagnosis and predictive performance; hence, they can be successfully implemented for improving current CVD diagnosis efforts and help patients around the world, especially in regions where medical staff is lacking.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

The coffee industry loses millions of dollars annually worldwide due to the Coffee Berry Borer (CBB); these losses imply a decrease in quality and production. Traps are used to monitor their flight and for pest control. The main objective was to determine the flight pattern and trap capture percentages of the CBB population over time using column traps (CTs) in two independent field experiments. CTs were composed of four traps installed at four different heights 0.5, 1.5, 2.5, and 3.5m above ground. Our results demonstrated a significant difference in CBB capture by traps placed at different heights above the ground. The CT capture maintained a pattern throughout this study's lag; the lower the height, the greater the percentage of CBBs captured. In Experiments A and B, the traps placed at 0.5m caught 67% and 85% of the CBBs captured, respectively. Furthermore, the trap set at 1.5m above the ground in the multi-level CT showed a higher capture percentage than the individually placed trap (also at 1.5m). The pattern of the capture and proportion of the CBB in the CTs were maintained throughout the study despite the season, changes in temperature, and relative air humidity. We suggested that CTs could be explored as a useful tool for capturing the CBB, considering its monitoring and management.

In birds, unlike mammals, there is no complete separation between the thoracic and abdominal cavities. Instead, they have the coelomic cavity where most main organs are found. Therefore, an adequate knowledge of the anatomy of the coelomic cavity is of great importance for veterinarians, biologists and the scientific community. This study aimed to evaluate the coelomic cavity anatomy in the Atlantic puffins (Fratercula Arctica) using anatomical sections and computed tomography images.

Abstract The modified Bessel function (MBF) of the first kind is a fundamental special function in mathematics with applications in a large number of areas. When the order of this function is integer, it has an integral representation which includes the exponential of the cosine function. Here we generalize this MBF to include a fractional parameter, such that the exponential in the previously mentioned integral is replaced by a Mittag-Leffler function. The necessity for this generalization arises from a problem of communication in networks. We find the power series representation of the fractional MBF of the first kind, as well as some differential properties. We give some examples of its utility in graph/networks analysis and mention some fundamental open problems for further investigation.

Piperine, an active plant alkaloid from black pepper (Piper nigrum), has several pharmacological effects: antioxidant, anti-inflammatory and immunomodulatory, which involves inhibiting molec-ular events associated with various stages of cancer development. The aim of this study was to investigate the molecular mechanisms of action of piperine in relation to its potential anticancer effect on head and neck cancer cells. Parameters related to neoplastic potential, analysis of cyto-kine, protein and gene expression were investigated in the head and neck cancer cell lines (HEp-2 and SCC-25) treated with piperine. The results of the tests indicated that piperine modified mor-phology, inhibited viability and the formation of cell colonies. Piperine promoted genotoxicity by triggering apoptosis and cell cycle arrest in G2/M and S. A decrease in cell migration was also observed, and decreased expression of MMP2/9 genes. Piperine also reduced the expression of inflammatory molecules (PTGS2 and PTGER4), regulated the secretion of cytokines (IF-y and IL-8) and modulated the expression of ERK and p38. These results suggest that piperine exerts anti-cancer effects on tumor cells, and could be a promising natural treatment by regulating signaling pathways associated with head and neck cancer.

Building roofs are sources of unwanted heat for buildings situated in zones with a warm climate. Thus, reflective coatings have emerged as an alternative to reject a significant fraction of solar energy received by roofs. In this research, the thermal behavior of concrete slab-type roofs with traditional and solar reflective coatings was simulated using a computational tool. Weather data from four cities in Mexico with a warm climate were used as boundary conditions. This tool is an in-house code based on the Finite Volume Method developed by the author to perform building components simulations. The code was validated with experimental data from previous work. A series of comparative simulations were developed, taking a gray roof as a control case. The results showed that for the roof without thermal insulation (single roof), the solar reflective coatings reduced the exterior surface between 11 and 16∘C. Consequently, the single roofs’ daily heat gain was reduced by a factor ranging between 41 and 54%. On the other hand, for the insulated roof, the reflective coatings reduced the exterior surface temperature between 17 and 21∘C. At the same time, the daily heat gain of composite roofs was reduced between 37 and 56%.

This article presents the results of the study on the elements and spaces that likes and dislikes’ historical urban landscape of Ibarra's city, Ecuador, based on the analysis of the urban image. This research aims to propose an objective way to intervene a historical landscape based on the opinion of the people who frequent the place. Our hypothesis is that the characteristics (age, gender, educational level, and frequency of visits) of the interviewees condition their judgment on liking and disliking. It is proposed to know which of these characteristics condition the judgment. The methodology has two parts: a descriptive statistical analysis with graphs and frequencies used to map each point on the maps, and a logistic regression model to study the relationships between liking and disliking with interviewee characteristics. As results, (1) it has been possible to obtain those elements or spaces that are liked and disliked in proportion graphs and in planimetry. (2) Explanatory analysis of liking and disliking through the logistic regression model and inference to study significant characteristics. It emphasizes that "frequency of visits" is the significant characteristic for the elements and spaces that dislike. It's concluded that the study carried out provides objective tools to obtain the opinion of people and it's useful seen it in planimetry. Also, could be establish priorities to urban authorities about improve and intervention on elements or spaces that people judge because they are liking or disliking.

Materials known as Nd:YAG are crystalline materials of the cubic system made from neodymium-doped yttrium aluminum garnet, which among others, have excellent optical properties. Nd:YAG four-level laser devices are highly used in both the health and industrial sectors. In this study, a simple and inexpensive alternative to manufacturing Nd:YAG materials through solid state reactions following powder processing routes was proposed. For this, an intense mixture of the precursor materials (Al2O3 and Y2O3) was carried out, followed by the addition of neodymium atoms to improve the optical properties of the resulting material. High energy mechanical mixing of the precursor powders resulted in submicron particles, with good size distributions of the powders. The advance of YAG formation was monitored by intermediate phase formation during heat treatment through interrupted tests at different temperatures and analysis by X-ray diffraction. From this analysis, it was found that reaction for the formation of the desired YAG is completed at 1500°C. Fourier-transform infrared spectroscopy analyses determined the presence of functional groups corresponding to the YAG. Finally, the study by optical emission spectroscopy showed wavelengths in agreement with the electronic structure of the elements of the synthesized Nd:YAG.

Demyelinating diseases alter myelin or the coating surrounding most nerve fibers in the central and peripheral nervous systems. The grouping of human central nervous system demyelinating disorders today includes Multiple Sclerosis (MS) and Neuromyelitis Optica Spectrum Disorders (NMOSD) as distinct disease categories. Each disease is caused by a complex combination of genetic and environmental variables, many involving an autoimmune response. Even though these conditions are fundamentally similar, research into genetic factors, their unique clinical manifestations, and lesion pathology has helped with differential diagnosis and disease pathogenesis knowledge. This review aims to synthesize the genetic approaches that explain the differential susceptibility between these diseases, explore the overlapping clinical features, and pathological findings, discuss existing and emerging hypotheses on the etiology of demyelination, and assess recent pathogenicity studies and their implications for human demyelination. This review presents critical information from previous studies on the disease, which asks several questions to understand the gaps in research in this field.

Acute and chronic bone infections, especially those caused by methicillin-resistant Staphylococcus aureus (MRSA), remains a major complication and therapeutic challenge. It is documented that local administration of vancomycin offers better results than the usual routes of administration (e.g. intravenous) when ischemic areas are present. In this work, we evaluate the antimicrobial efficacy against S. aureus and S. epidermidis and analyzed the potential cytotoxic effect of a novel hybrid 3D-printed scaffold based on poly(caprolactone) and chitosan loaded with different vancomycin concentrations (1, 5, 10 and 20%). For this purpose, vancomycin release was measured by means of HPLC, and the biological response of ah-BM-MSCs in the presence of the scaffolds was evaluated in terms of cytotoxicity (LDH activity), proliferation (AlamarBlueⓇ) and osteogenic differentiation (ALP activity, Alizarin Red staining). In addition, two cold plasma treatments were evaluated to improve the adhesion of hydrophobic polymers to hydrogels. The hybrid PCL/CS/Van scaffolds tested were found to be biocompatible, bioactive, and bactericide, as demonstrated by no cytotoxicity or functional alteration and by bacterial inhibition. Our results suggest that the scaffolds developed would be excellent candidates to be used in a wide range of biomedical fields such as drug delivery systems or tissue engineering applications.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

Lathyrane-type diterpenes have a wide range of biological activities. Among them, euphoboetirane A (1) exerts neurogenesis-promoting activity. In order to increase the structural diversity of this type of lathyranes to explore their potential use in neurodegenerative disorders, the biotransformation of 1 by Streptomyces puniceus BC-5GB.11 has been investigated. The strain BC-5GB.11, isolated from surface sediments collected from the intertidal zone of the inner Bay of Cadiz, was identified as Streptomyces puniceus, as determined by phylogenetic analysis using 16S rRNA gene sequence. Biotransformation of 1 by BC-5GB.11 afforded five products (3-7), all of them reported here for the first time. The main biotransformation pathways involved regioselective oxidation at non-activated carbons (3-5) and isomerization of the D^12,13 double bond (6). In addition, a cyclopropane-rearranged compound was found (7). The structures of all compounds were elucidated on the basis of extensive NMR and HRESIMS spectroscopic studies.

Contamination by microplastics (MP) in aquatic ecosystems is largely due to the release of millions of these particles from treated effluents from Wastewater Treatment Plants (WWTP). Due to the lack of policies and regulations that establish criteria for the control and elimination of MP from WWTP effluents, this research evaluated the presence of MP for particle sizes of 38 and 150 µm in influents and effluents from three WWTP in the port of Acapulco, Mexico. Using optical microscopy and Fourier transform infrared spectroscopy (FTIR) techniques, the MP detected were polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET) and polyvinyl chloride (PVC). MP removal efficiencies of 82.5 to 98.7% (38 µm) and 86.8 to 97.5% (150µm) were obtained; the MP average daily emissions to the receiving bodies of these three WWTPs were in the ranges of 9.5 x 106 - 4.70 x 108 particles and the annual emissions in the range of 3.05 x 109 - 1.72 x 1011 particles. This work reveals the urgency of implementing regulatory policies to avoid the continuous emission of MP to aquatic ecosystems from WWTPs in Acapulco, Mexico.

Varroa destructor is considered one of the most devastating parasites of the honey bee, Apis mellifera, and a major problem for the beekeeping industry. Currently, the main method to control Varroa mites is the application of drugs that contain different acaricides as active ingredients. The pyrethroid tau-fluvalinate is one of the acaricides most widely used in beekeeping due to its efficacy and low toxicity to bees. However, the intensive and repetitive application of this compound produces a selective pressure that, when maintained over time, contributes to the emergence of resistant mites in the honey bee colonies, compromising the acaricidal treatments efficacy. Here we studied the presence of tau-fluvalinate residues in hives and the evolution of genetic resistance to this acaricide in Varroa mites from honeybee colonies that received no pyrethroid treatment in the previous four years. Our data revealed the widespread and persistent tau-fluvalinate contamination of beeswax and beebread in hives, an overall increase of the pyrethroid resistance allele frequency and a generalized excess of resistant mites relative to Hardy-Weinberg equilibrium expectations. These results suggest that tau-fluvalinate contamination of the hives may seriously compromise the efficacy of pyrethroid-based mite control methods.

Development of non-conventional hybrids (NCHs) responds to the demand for the Elotes Occidentales 'EO' race for production of pozole. The effect of: crop cycle (2019, 2020 and 2021) on physical characteristics, flowered grain quality and phytochemical content of two HNC (Pz1 and Pz2) of pozolero maize, as well as the effect of the presence or absence of pedicel, type of pollination (open and controlled, 2019), and progenitor lines (female and male, 2020) on flowered grain quality and content of phytochemical compounds were evaluated. Size, hardness, color, total phenols and anthocyanins in unprocessed grain were determined, and yield, volume and puncture strength in flowered grain. Results were analyzed with a factorial arrangement in a completely randomized design. There were significant differences (p≤0.05) in most of the variables studied by effect of crop cycle and genotype. NCHs had large grains (40 g 100 grains-1), soft endosperm (IF&gt; 60), pink-purple color, and phenol and anthocyanin contents similar to those reported for the 'EO' race. The presence or absence of the pedicel did not affect flowered grain quality. Controlled pollination favored anthocyanin synthesis. The anthocyanin content of NCHs was determined by the female line. Thermal processing reduced anthocyanins by 60%; however, they leached into the flowering broth, so that the pozole made from NCHs improves the nutraceutical value of the pozole, relative to that of pozole made with Cacahuacintle maize.

Adhesion systems are very important in robots for infrastructure inspection (especially in vertical walls). They present the challenge of optimizing the ratio vacuum/power consumption in battery-powered robots. In this paper a CFD (Computer Fluid Dynamics) modelling and optimization process of a robot adhesion system is carried out to determine the best performing configuration in terms of vacuum and power consumption. Analytical and numerical models were developed to predict the behaviour of the system for different configurations. The models were validated, using test rig measurements, by calibrating an arbitrary defined inlet height that simulates the leakage flow. Then, different geometric parameters were varied to determine the best performing configuration based on the vacuum/power consumption ratio value. The model presented in the paper was capable of predicting the behaviour of the system for different configurations, with a margin of error of 15% for the vacuum prediction and a 25% for the motor power calculation. Finally, the model was used to optimize parameters of the system, like the number of blades of the impeller. The adhesion system was conceived for the modular autonomous climbing legged robot ROMERIN.

COVID-19 is frequently associated with a coagulopathy with severe consequences. The mechanisms leading to a pro-coagulant state in these patients is multifactorial, including tissue destruction and inflammatory mechanisms. Based on the analysis of publicly available interactomes, we propose that SARS-CoV-2 infection causes a deficiency in C1 esterase inhibitor (C1-INH), a pathogen-specific mechanism that may help explain the pro-coagulant state in COVID-19 patients.

The sense of uncertainty and fragility due to the effects and magnitude of global challenges we are facing (from pandemic circumstances to climate change impacts) requires – much more than in the past – the capacity to generate a visionary and forefront design approach in the young gen-erations aiming at stimulating their reaction attitude rather than providing consolidated tools from past conditions that no longer exist or will rapidly evolve. Within this general framework, we have investigated the effectiveness and impacts of experienced-based methods of learning and innovative educational tools in architecture aimed at shaping expertise in which the environ-mental dimension and the climate-change challenge dialogues with the context's complexity in terms of socio-cultural dynamics, real potentialities and constrains, addressing their transdisci-plinary trajectories. The paper analyses 5 international pioneering teaching experiences that provide the opportunity to understand the outcomes of collaborative and experiential learning processes in which the educational activities leverage a dialogue between diverse communities (academia-citizens-policymakers-practitioners). The study outcomes show that shifting the pedagogical paradigm towards in-field-experience-based models can improve the awareness of future practitioners for climate implications of architectural design, implement their analysis and project skills while triggering processes of knowledge transfer and co-production at community level, and allow them to better address the societal and cultural issues involved within decision making.

Two polyurethanes (PUs) were similarly synthesized by reacting a cycloaliphatic isocyanate with 1,4 butanediol and two polyols of different nature (polyester, polycarbonate diol) with molecular weights of 1000 Da. The PU made with polycarbonate diol polyol (YCD) was the only showing intrinsic self-healing at 20 °C. For assessing the mechanism of intrinsic self-healing of YCD, a structural characterization by molecular weights determination, infrared and X-ray photoelectronic spectroscopies, differential scanning calorimetry, X-ray diffraction, thermal gravimetric analysis and dynamic mechanical thermal analysis was carried out. It was concluded that the self-healing at 20 °C of YCD was due to non-covalent dynamic exchange interactions among the carbonate groups of the soft segments. Therefore, the chemical nature of the polyol played a key role in developing PUs with intrinsic self-healing at 20 °C.

Background: Modern MEG devices include 102 sensor triplets containing one magnetometer and two planar gradiometers. The first processing step is often a signal space separation (SSS), which provides a powerful noise reduction. A question commonly raised by researchers and reviewers is which data should be employed in source reconstruction: (1) magnetometers only, (2) gradiometers only, (3) magnetometers and gradiometers together. The MEG community is currently divided about the proper answer and strong arguments in favor and against these three approaches often expressed. Methods: First, we provide theoretical evidence that both gradiometers and magnetometers contain the same information after SSS, and argue that they both result from the backprojection of the same SSS components. Then, we compare beamforming source reconstructions from magnetometers and gradiometers in real MEG recordings before and after SSS. Results: Without SSS, the correlation between source time series extracted from magnetometers and gradiometers was high, with Pearson correlation coefficient r=0.5-0.8. After SSS, these correlation values increased dramatically, reaching over 0.90 across all cortical areas. Conclusions: After SSS, almost identical source reconstructions (r>0.9) can be obtained with magnetometers and gradiometers, as long as regularization is selected appropriately to account for the different properties in magnetometers and gradiometers covariance matrices.

Statistical based reconstruction methods and signal processing tooling techniques are implemented and used to detect delaminations or debondings within composite items. From literature it appears that, although a single procedure for the estimation of the structural health is a fast solution, a multiple analysis based on different reconstruction methods or different damage parameters could provide more detailed information about the location and the severity of possible failures. This work discusses the advantage of using cross-correlation analysis in a data-driven approach based on ultrasonic guided waves (GW) tomographic technique and piezoelectrics (PWAS) in pitch-catch configuration. In this sense, this work evidences an improvement in damage detection when the cross-correlation is included as part of the GW-based system for damage assessment approach. The specimens used as test structures to demonstrate the validity of the methodology derive from an aircraft wing test article where damages are specified as skin delamination produced by low energy impact.

The antioxidant, antimicrobial, antiproliferative, and enzyme inhibitory properties of five extracts from aerial parts of Salvia pachyphylla were examined to assess the prospective of this plant as a source of natural products with therapeutic potential. Those properties were analyzed performing a set of standard assays. The extract obtained with dichloromethane showed the most variety of components, as yielded promising results in all completed assays. Furthermore, the extract obtained with ethyl acetate exhibited that greatest antioxidant activity as well as the best xanthine oxidase inhibitory activity. Remarkably, both extracts obtained with n-hexane or dichloromethane revealed significant antimicrobial activity against the Gram-positive bacteria; also, they showed greater antiproliferative activity against three representative cell lines of the most common types of cancers in women worldwide, and against a cell line that exemplifies cancers that typically develop drug resistance. Despite that other extracts were less active, such as the methanolic or aqueous, their results are promising for the isolation and identification of novel bioactive molecules.

This work demonstrates the antimycotic activity and structural damage of stingless bee propolis against Malassezia pachydermatis,causative agent of canine otitis.Two propolis ethanolic extracts(EEP) derived from the stingless bees, Scaptotrigona mexicana and Tetragonisca angustula were tested against three clinical strains of Malassezia pachydermatis and one of reference (ATCC 14522). Each ethanolic extract of propolis was analyzed by Gas Chromatography – Mass Spectrometry(GC-MS). Antimycotic activity was evaluated by plate microdilution. To evaluate the induced changes in yeasts, by fluorescence microscopy, stains were performed with chalcofluor white and propidium iodide. For both propolis, sesquiterpenes were the main components determined by GC-MS. Minimum inhibitory concentration (MIC) of 32 mg/mL and a minimum fungicidal concentration of 64 mg/Ml were determined in both extracts. EPP of Scaptotrigona mexicana and Tetragonisca angustula caused significant damage to yeast morphology. Propidium iodide penetration was observed, indicating damage to the yeast and with calcofluor-white stain, only morphology deformation was observed..The antimycotic activity and structural damage of propolis from Scaptotrigona mexicana and Tetragonisca angustula against Malassezia pachydermtais was demonstrated .This probably being the first scientific report that demonstrates structural damage in Malassezia pachydermatis of Mexican stingless bee propolis

Wearable vital signs monitoring and specially the electrocardiogram have taken important role due to the information that provide about high-risk diseases, it has been evidenced by the needed to increase the health service coverage in home care as has been encouraged by WHO. Some wearables devices have been developed to monitor the ECG in which the location of the measurement electrodes is modified respect to the Einthoven model. However, mislocation of the electrodes on the torso can lead to the modification of acquired signals, diagnostic mistakes and misinterpretation of the information in the signal. This work presents a volume conductor evaluation and an ECG signal waveform comparison when the location of electrodes is changed, to find a electrodes’ location that reduces distortion of interest signals. In addition, effect of motion artifacts and electrodes’ location on the signal acquisition are evaluated. A group of volunteers was recorded to obtain ECG signals, the result was compared with a computational model of the heart behavior through the EA ECG, DTW and SNR methods to quantitatively determine the signal distortion. It was found that while the Einthoven method is followed, it is possible to acquire the ECG signal from the patient’s torso or back without a significant difference, and the electrodes position can be moved 6cm at most from the suggested location by the Einthoven triangle in Mason-Likar’s method.

The aim of this study was to evaluate the intensity of the annual sexual behavior (SB) of Boer bucks under tropical conditions in southern Mexico. For one year, 16 extensively grazing males were evaluated for SB individually with estrogenized goats. From the beginning of the experiment and every 30 days, body weight (BW), body condition (BC), testicular circumference (TC), odor intensity (OI) and SB (nudging, ano-genital sniffing, flehmen, mounting attempts, mounts with intromission, and self-urination) were recorded. The bucks showed a more intense SB during the months of November to May than during the months of June to October (p < 0.05). Greater frequency was found for nudging, ano-genital sniffing, mounting attempts, and self-urination in the months of November to May (p < 0.001). BW was lower during the months of January to August than in the months of September to December (p < 0.05). On the other hand, TC increased from October to December (p < 0.05). Similarly, the OI in males varied over time (time effect; p < 0.001). In fact, an increased odor was found from October to December. The conclusions were that breed male goats from the tropics of Guerrero have a more intense SB during the months of November to May, which corresponds to the time of the year when forage availability is the greatest.

Background: Hereditary Hemorrhagic Telangiectasia (HHT) is a vascular autosomically inherited rare disease. Epistaxis (nose bleeds) is the most common symptom in HHT, leading to anemia and affecting patient’s quality of life. In addition to epistaxis, gastrointestinal bleeding (GI), more often at older ages, may lead to severe anemia and need for blood transfussions. Thus, finding drugs to control both types of bleeding is a primary necessity in HHT. Methods: A cross-sectional observational study was conducted in a series of 11 HHT patients treated with low tacrolimus doses (0.5-1mg) on an off-label prescription basis. Patients showed refractory bleeding to previous treatments. Epistaxis severity score (ESS) and hemoglobin levels were parameters used to evaluate tacrolimus impact. The occurrence of side effects was also recorded. Results: Tacrolimus was well tolerated in most of the patients, except in 2 which abandoned the treatment. The remaining patients tolerated the treatment, with a general improvement in their health condition. Epistaxis was significantly reduced comparing the ESS before and after treatment. Hemoglobin levels were significantly increased overcoming the anemia in the course of the treatment. Conclusion: Tacrolimus at low doses should be considered as a promising treatment for bleeding derived of epistaxis and GI in HHT.

Mannheimia haemolytica is the main pathogen contributing to pneumonic pasteurellosis in sheep. The aim of this study was to investigate the antimicrobial resistance levels in M. haemolytica from the lungs of slaughtered sheep and the genetic resistance mechanisms involved. A total of 256 M. haemolytica isolates, 169 from lungs with pneumonic lesions and 87 without, were analyzed by the disk diffusion method for 12 antimicrobials, and the whole genome of 14 isolates sequenced to identify resistance determinants. Levels of phenotypic resistance ranged from <2 % for 10 antimicrobials (amoxicillin, amoxicillin-clavulanic, ceftiofur, cefquinome, lincomycin/spectinomycin, gentamicin, erythromycin, florfenicol, enrofloxacin, and doxycycline) to 4.3% for tetracycline and 89.1% for tylosin. Six isolates carried tetH genes and four carried, in addition, strA and sul2 genes in putative plasmid sequences. No mutations associated with macrolide resistance were identified in 23 rDNA sequences suggesting that M. haemolytica phenotypic results for tylosin should be interpreted with care in the absence of well-established epidemiological and clinical breakpoints. The identification of strains phenotypically resistant to tetracycline and of several resistance genes, some of which were present in plasmids, highlight the need for continuous monitoring of susceptibility patterns in Pasteurellaceae isolates from livestock

Background and Objectives: The purpose of this study was to describe and evaluate the bleeding that occurs during the first weeks of gestation and its implications throughout pregnancy. Secondarily, we assessed the associated complications in order to identify potential risk factors that could be used to select women at higher risk of adverse outcomes that could benefit from an early diagnosis and improved monitoring. Materials and Methods: We made a selection of all the women who consulted in the Emergency Department of the Hospital QuirónSalud in Malaga on 2015 presenting with first trimester metrorrhagia. We refer to first trimester metrorrhagia as that which occurs until week 12+6. Once these pregnant women were identified, we studied several variables not related to the gestation and some others associated with it and its natural course. Results: The average age of the patients assessed was 34.1. Associated gestational complications were metrorrhagia in the second trimester (6.3%), threatened preterm labour (7.4%), preeclampsia (2.5%), gestational diabetes (7.4%), late abortion (1.2%) and early postpartum hemorrhage (1.8%). We sought associations to assess possible risk factors, establishing an increased maternal age as an aggravating factor for the development of complications. We also studied gestational complications finding a higher prevalence of them in older women, such as prematurity (33.11 vs 34.48 years), gestational diabetes (33.11 vs 36.06 years) and preeclampsia (33.25 vs 35 years). Conclusions: Maternal age is a risk factor for first-trimester spontaneous miscarriage and for the development of complications of pregnancy. It is crucial to perform a correct screening of different pathologies throughout the pregnancy to anticipate potential complications.

Oral pyogenic granuloma (PG) is generally a solitary benign connective tissue proliferation of unknown etiology. It is the most common type of oral inflammatory hyperplasia histologically characterized by proliferation of granulation tissue with inflammatory infiltrates and high angiogenic capacity. Vascular neoformations of different diameters are usually present. Due to their structural characteristics, tendency to bleed, and rapid and alarming growth rate, these neoformations may have serious consequences. Sometimes, it is complex to make an accurate diagnosis. Therefore, adequate management and treatment are based on the characteristics and systemic conditions of each patient. This review was carried out to provide an overview of the factors involved in, or attributed to the etiopathogenesis of oral PG. It describes the different forms of presentation and clinical evolution, as well as the most frequent signs and symptoms that characterize this disease, while incorporating recent radiographic and microscopic findings. In addition, it describes the different modalities for the management of oral pyogenic granuloma depending on the particular characteristics of each patient.

Sars-CoV-2 outbreak represents a public health emergency, affecting different regions of the world. Lung is the organ more damaged due to the high presence of Sars-CoV-2 binding receptor ACE2 on epithelial alveolar cells. Severity of infection vary from absence of symptomatology to be more severe, characterized by acute respiratory distress syndrome (ARDS), multiorgan failure and sepsis requiring treatment in Intensive Care Unit (ICU).It is not still clear why in a small percentage of patients immune system is not able to efficiently suppress viral replication. It has been documented as predictive factors for severity and susceptibility affections of cardiovascular system such as heart failure (HF), coronary heart disease (CHD) and risk factors for atherosclerotic progression, hypertension and diabetes among others.Atherosclerotic progression, as chronic inflammation process, is characterized by immune system dysregulation leading to pro-inflammatory pattern, including (Interleukin 6) IL-6, Tumor Necrosis Factor α (TNF-α) and IL-1β raise. Reviewing immune system and inflammation profiles in atherosclerosis and laboratory results report in severe Sars-CoV-2 infection we have supposed a pathogenetic correlation. Atherosclerosis may be a pathogenetic ideal substrate to high viral replication ability leading to adverse outcomes, how reported in patients with cardiovascular factors. Moreover, level of atherosclerotic progression may impact on a different degree of severe infection and in a vicious circle feeding itself Sars-CoV-2 may exacerbate atherosclerotic progression due to excessive and aberrant plasmatic concentration of cytokines.

Primary ciliary dyskinesia (PCD) is an inherited disorder that impairs motile cilia, essential for respiratory health, with a reported prevalence of 1 in 16,309 within Hispanic populations. Despite having the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in 70% of Puerto Rican patients, the characterization of the ciliary dysfunction remains unidentified due to the unavailability of advanced diagnostic modalities like High-Speed Video Microscopy Analysis (HSVA). Our study implemented HSVA for the first time on the island as a tool to better diagnose and characterize the RSPH4A [c.921+3_921+6del (intronic)] founder mutation in Puerto Rican patients. By applying HSVA, we analyzed the ciliary beat frequency (CBF) and pattern (CBP) in native Puerto Rican patients with PCD. Our results showed decreased CBF and a rotational CBP linked to the RSPH4A founder mutation in Puerto Ricans, presenting a novel diagnostic marker that could be implemented as an axillary test into the PCD diagnosis algorithm in Puerto Rico. The integration of HSVA technology in Puerto Rico substantially enhances the framework for PCD evaluation and diagnosis, facilitating prompt detection and early intervention for improved disease management. This initiative, demonstrating the potential of HSVA as an adjunctive test within the PCD diagnostic algorithm, could serve as a blueprint for analogous developments throughout Latin America.

We studied the link between carbon and water fluxes to understand the response of net ecosystem carbon exchange (NEE) to water availability conditions of three different potato water regimes cropping systems [full irrigation (FI), deficit irrigation (DI) and rainfed (RF)]. Through the eddy covariance technique, we measured CO₂ and water vapor exchanges and determined surface resistances, omega factor, and inherent water use efficiency (IWUE). Additionally, continuous plant growth determinations of leaf area index (LAI) and specific leaf area (SLA) were made over the three cropping systems. The RF potato was a net carbon source (NEE = 187.21 ± 3.84 g C m⁻²), while both, FI (NEE= −311.96 ± 12.82 g C m⁻²) and DI (−17.3 ± 4.6 g C m⁻²) were a net carbon sink. Greater sink activity is due to high fluxes of gross primary productivity (GPP) [where the GPP > ecosystem respiration (R_eco)] and evapotranspiration (ET), and the high efficiency in the exchange of carbon and water. Without water limitations, the larger canopy, with greater photosynthetic activity (GPP/R_eco > 2) as well as with low internal resistance offers a greater area for water and carbon exchange, and the highly coupled and synchronized ET – GPP fluxes are primarily controlled by the radiative environment. The lower sink capacity of the DI potato crop and the carbon source activity from the RF, are consequences of a smaller area for water and carbon exchange due to the smaller canopy, and a low IWUE from decoupled and desynchronized carbon and water exchange caused by unbalanced restrictions on ET and GPP fluxes. Specifically, at DI potato, ET remained at a high rate, while GPP was reduced by means of non-stomatal limitations. In the rainfed potato, vapor pressure deficit (VPD) played a significant role increasing midday canopy resistance (Rc) up to 13 times compared to irrigated sites, when VPD was around 0.8 kPa. In consequence, ET and GPP fluxes decreased together, but GPP decreased more than ET because of stomatal and non-stomatal limitations.

This article presents a unique set of voltage and current data from a public building and acquired using a hybrid measurement solution that combines Python and Grafana. The transversal purpose consists of contributing to the community with a vision of the quality of the supply more oriented to the monitoring of the state of the network, providing a more realistic vision, which allows a better understanding, and the adoption of the best decisions to achieve the efficient energy management and thus optimize the operation and maintenance of power systems. The work focuses on higher order statistical estimators that, combined with exploratory data analysis techniques, improve the characterization of the shape of the stress signal. These techniques and data, together with the acquisition and monitoring system, present a unique combination in the line of low-cost measurement solutions. It also incorporates the underlying benefit of the contribution to industrial benchmarking. The paper also includes a computational comparison between Python and LabVIEW to elicit the performance of the measurement solution.

This review documents an emerging body of evidence concerning the neurological effect of polycyclic aromatic hydrocarbon (PAH) exposure, with regard to cognitive function and increased risk of neurodegeneration. Two electronic databases PubMed and Web of Science were systematically searched. The 37/428 studies selected included outcomes measuring cognitive function, neurobehavioral symptoms of impaired cognition, and pathologies associated with neurodegeneration from prenatal (21/37 studies), childhood (14/37 studies), and adult (8/37 studies) PAH exposure. Sufficient evidence surrounding prenatal exposure negatively impacting child intelligence, mental development, average overall development, verbal IQ, memory impairment, externalizing, internalizing, anxious, depressed behaviours, behavioural development and child attentiveness was found. Evidence concerning exposure during childhood and as an adult was scarce and highly heterogeneous, however presence of neurodegenerative biomarkers and increased concentrations of cryptic “self” antigens in serum and cerebrospinal fluid samples suggest a higher risk of neurodegenerative disease. Associations with lowered cognitive ability, and impaired attentiveness were found in children and memory disturbances, specifically auditory memory, verbal learning and general memory in adults. Although evidence is not yet conclusive and further research is needed the studies included supported the hypothesis that PAH exposure negatively impacts cognitive function and increases the risk of neurodegeneration in humans, and recommends considering the introduction of a variable “rural vs. urban” as covariate for adjusting analyses where the neurological functions affected (as result of our review) are outcome variables.

The present study evaluates the psychometric properties of the Conflicts in Romantic Relationships Over Facebook Use Scale with a sample of Puerto Rican adults. A total of 577 Puerto Ricans participated on this confirmatory and psychometric study. The results confirmed that the scale has a multidimensional structure. These dimensions are: Partner Facebook intrusion, Conflict over Facebook use, and Jealousy over Facebook use. A total of 18 items complied with the criteria of discrimination and presented appropriate factorial loads (6 items per dimension). The Cronbach’s Alpha indexes of the dimensions ranged between .87 and .95 and the omega coefficients ranged between .88 and .95. In summary, the instrument has the appropriate psychometric properties to continue with validation studies, as well as to be implemented in various work areas, both theoretical and applied.

In this part of the series of two papers, we extend the theorems discussed in part I for infinite series. We then use these theorems to develop distinct novel results involving the Hurwitz zeta function, Riemann zeta function, Polylogarithm and Fibonacci numbers. In continuation, we obtain some zeros of the newly developed zeta functions and explain their behaviour using plots in complex plane. Furthermore, we provide particular cases for the theorems and corollaries which show that our results generalise the currently available functions and series such as the Riemann zeta function and the geometric series. Finally, we provide four miscellaneous examples to showcase the vast scope of the developed theorems.

p-type Ag-N dual acceptor doped ZnO thin films with long electrical stability were deposited by DC magnetron reactive co-sputtering technique. After deposition, the films were annealed at 400 °C for one hour in a nitrogen-controlled atmosphere. The deposited films were amorphous. However, after annealing they crystallize in the typical hexagonal wurtzite structure of ZnO. The Ag-N dual acceptors were incorporated substitutionally in the structure of zinc oxide and achieving that the three samples presented the p-type conductivity in the ZnO. Initial electrical properties showed a low resistivity of from 1 to10^{−3} Ω.cm, Hall mobility of tens cm2/V.s and a hole concentration from 10^{17} to 10^{19} cm^{−3}. The electrical stability analysis reveals that the p-type conductivity of the ZnO:Ag,N films is very stable and does not revert to n-type, even after 36 months of aging. These results reveal the feasibility of using these films for applications in short-wavelength or transparent optoelectronic devices.

Objectives: To assess the short-term impact of a single global stretching session on plantar pressures and lumbar range of motion (RoM) over one week in sedentary university students. Design: A randomised controlled trial with two parallel groups. Participants: Sixty-four university students were randomly assigned to a stretching group or control group. The stretching group received a single session of global stretching and the control group remained seated for the same length of time as the stretching session. Main outcome measures: Lumbar RoM and plantar pressures were assessed before, immediately after, 48 hours after, and 7 days after intervention. Results: Group-by-time interaction was significant for lumbar lateral flexion (p = 0.044), right maximal pressure (p = 0.003), left maximal pressure (p = 0.008), right mean pressure (p = 0.025), left mean pressure (p = 0.002), and maximal pressure minus mean pressure in right foot (p = 0.007). The model with plantar pressures showed a significant difference for group-by-time interaction (p = 0.010).Conclusion: Global stretching seems to counteract the ill-effects of prolonged sitting up to seven days with respect to plantar pressure in standing without improving lumbar ROM

The aim of the present work was to evaluate the effects of Thalassia testudinum hydroethanolic extract, its polyphenolic fraction, and thalassiolin B on the activity of phase I metabolizing enzymes as well as their antimutagenic effects. Spectrofluorometric techniques were used to evaluate the effect of tested products on rat and human CYP1A and CYP2B activity. The antimutagenic effect of tested products was evaluated in benzo[a]pyrene (BP)-induced mutagenicity assay by Ames test. Finally, the antimutagenic effect of Thalassia testudinum (100 mg/kg) was assessed in a BP-induced mutagenesis in mice. The tested products significantly (p<0.05) inhibit rat CYP1A1 activity, acting as mixed-type inhibitors of rat CYP1A1 (Ki = 54.16±9.09 μg/mL, 5.96±1.55 μg/mL and 3.05±0.89 μg/mL, respectively). Inhibition of human CYP1A1 was also observed (Ki = 197.1±63.40 μg/mL and 203.10±17.29 μg/mL for the polyphenolic fraction and for thalassiolin B, respectively). In addition, the evaluated products significantly inhibit (p<0.05) benzo[a]pyrene (BP)-induced mutagenicity in vitro. Furthermore, oral doses of Thalassia testudinum (100 mg/kg) significantly reduced (p<0.05) the BP-induced micronuclei and oxidative damage, together with an increase of glutathione, in mice. In summary, Thalassia testudinum metabolites exhibit antigenotoxic activity mediated, at least, by the inhibition of CYP1A1-mediated BP biotransformation. Thus, the metabolites of T. testudinum may represent a potential source of chemopreventive compounds for adjuvant therapy of cancer.

Dioscorea composita is a plant native to México and Central America with a high concentration of diosgenin precursors. Currently, México is one of the two most important countries producers of this yam; however, climate change is altering the environmental conditions of its natural habits, threatening its preservation and productivity. This is why this research was focused to characterize the eco-geography of D. composita and predict its potential geographic distribution under climate change scenarios in México-Central America. A collection of 408 geo-referenced accessions was used to determine its climatic adaptation, ecological descriptors, and the current and future potential geographic distribution, which was modeled with MaxEnt model through the Kuenm R-package. For future climate scenarios, an ensemble of the GCMs HadGEM-ES and CCSM4 was used. Results showed that D. composita adapts to warm humid and very humid agro-climates and that the most contributing variables for its presence are annual and seasonal moisture availability indices, seasonal photoperiod, annual thermal range, Bio14 and Bio11. The year 2050 RCP 4.5 climate scenario would contract the potential distribution of D. composita, whilst the 2050 RCP 8.5 scenario would expand it, indicating that this species could be a good crop option under this scenario of emissions.

The current management of colorectal cancer liver metastasis (CRCLM) patients involves a multidisciplinary approach with surgical resection remaining the primary curative option. The advances in liver surgery have improved outcomes, enabling more patients to undergo surgery successfully. In addition, the development of imaging software has improved the preoperative planning and patient selection for surgery and other interventions. Systemic therapies, such as targeted therapies and immunotherapies have enhanced the chances of complete resection. Targeted agents in combination with chemotherapy, have shown efficacy in downstaging tumors and increasing resectability.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

A method for infrared and cameras sensor fusion, applied to indoor positioning in intelligent spaces, is proposed in this work. The fused position is obtained with a maximum likelihood estimator from infrared and camera independent observations. Specific models are proposed for variance propagation from infrared and camera observations (phase shifts and image respectively) to their respective position estimates and to the final fused estimation. Model simulations are compared with real measurements in a setup designed to validate the system. The difference between theoretical prediction and real measurements is between 0.4 cm (fusion) and 2.5 cm (camera), within a 95% confidence margin. The positioning precision is in the cm level (sub-cm level can be achieved at most tested positions) in a 4x3 m locating cell with 5 infrared detectors on the ceiling and one single camera, at distances from target up to 5 m and 7 m respectively. Due to the low cost system design and the results observed, the system is expected to be feasible and scalable to large real spaces.

With the growing demand for personal protective equipment (PPE) in the face of the pandemic events caused by SARS-COV-2, the opportunity arises for the development of materials with characteristics such as antimicrobial, antiviral, antifungal activity, etc. The use of polymeric nanocomposites based on polyester/copper offers an alternative of great interest due to the versatility of the raw material and the high efficiency of copper as an antimicrobial additive. In this study, textile fibers prototypes with different Cu nanoparticles (CuNP) content were produced using melt-spinning to obtain bi-component multifilament fibers, and melt-blowing to obtain non-woven fabrics. The prototypes were tested against different pathogenic microorganisms such as S. aureus, E. coli, and C. albicans. It was shown that bi-component fibers offer more excellent protection against pathogens, while non-woven fabric only shows activity against E. coli. It was possible to identify that the CuNP were confined exclusively in the outer cover of the bi-component fibers, using different analytical techniques, which may be associated with the increase in antimicrobial activity, compared to the fibers present in the non-woven fabric, even when they present the same CuNP content.

(1) Background: Grapes and their associated by-products (as grape pomace, GP) stand out for their polyphenol content, which makes them a source of bioactive compounds with antioxidant capacity. The aim of this research was to determine if the inclusion of 50 g/kg of GP in the diet of hens could enrich egg with antioxidants and to study its effect on internal and external egg quality parameters. (2) Methods: A trial was conducted with two genetic lines of hens, which were fed either a control diet or a diet containing 50 g/kg of GP. Performance, internal and external egg quality, and egg yolk content of vitamins E and A, and gallic acid were determined; (3) Results: In eggs laid by hens fed GP diet, Haugh units and yolk colour score were enhanced, and eggshell became thinner, but without affecting the breaking strength. No dietary effect was observed on vitamin contents in yolk. Higher gallic acid content was observed in yolk of eggs laid by hens fed the GP diet, suggesting that some dietary phenolic compounds could be transferred to the eggs. Hen genetics influenced egg weight, albumen Haugh units, shell thickness and α- and γ-tocopherol concentration in yolks; (4) Conclusions: Dietary inclusion of GP improved the internal quality of eggs, enriching yolks with a phenolic compound, but reduced shell thickness.