This paper studies the performance improvement of the IEEE 802.15.4 nonbeacon-enabled mode originated by the inclusion of the Request-To-Send/Clear-To-Send (RTS/CTS) handshake mechanism resulting in frame concatenation. Under IEEE 802.15.4 employing RTS/CTS, the backoff procedure is not repeated for each data frame sent but only for each RTS/CTS set. The maximum throughput and minimum delay performance are mathematically derived for both the Chirp Spread Spectrum and Direct Sequence Spread Spectrum Physical layers for the 2.4 GHz band. Results show that the utilization of RTS/CTS significantly enhances the performance of IEEE 802.15.4 applied to healthcare in terms of bandwidth efficiency.

Usually, in ground-penetrating radar (GPR) datasets the user defines the limits between the useful signal and the noise through standard filtering to isolate the effective signal as much as possible. However, there are true reflections that mask the coherent reflectors that can be considered noise. In archaeological sites these clutter reflections are caused by scattering with origin in subsurface elements (e.g., isolated masonry, ceramic objects and archaeological collapses). Its elimination is difficult because the wavelet parameters similar to coherent reflections and there is a risk of creating artifacts. In this study a procedure to filtering the clutter reflection noise (CRN) from GPR datasets is presented. The CRN filter is a singular value decomposition-based method (SVD), applied in the 2D spectral domain. This CRN filtering was tested in a dataset obtained from a controlled laboratory environment, to establish a mathematical control of this algorithm. Also, it has been applied in a 3D-GPR dataset acquired in the Roman villa of Horta da Torre (Fronteira, Portugal), which is an uncontrolled environment. The results show an increase in the quality of archaeological-GPR planimetry that were verified via archaeological excavation.

The Roman villa of Pisões (Beja, Portugal), was part of the Lusitanian colony of Pax Iulia. This place stands out for the predominance of the water element in several structures of the villa, highlighting the balneum and the large natatio, one of the largest known in Roman Hispania. The records of the initial excavations that took place since 1967 do not allow the establishment of clear functionalities of the villa. The University of Évora, owner of the site, conceived an action plan for the requalification and enhancement of the archaeological site. One of the tasks aims to investigate using Applied Geophysics. This work analyses the landscape directly related to the villa, given that it is in the flooded area of a river, with a Roman containment dam. It is uncertain whether the water supply comes from this structure or other nearby springs. The use of ground-penetrating radar, combined with unnamed aerial vehicles, all integrated in a geographic information system, allows us to know the location of underground water connections and create a topographic model with high resolution. Considering all the information, we propose a model for the water transport inside the villa and estimate the location of the water supply.

INT-FFT algorithm presented in this work uses an interpolation methodology to densify 3D-GPR datasets to sharpen images obtained in GPR surveys obtained in an archaeological context. It allows the reconstruction of missing data from the combined use of mathematical transforms (e.g., the Fourier and Curvelet transform) and predictive filters. This technique makes it possible to calculate the missing signal simply by meeting two requirements: the data in the frequency domain must be limited in a range of values and must be able to be represented by a distribution of Fourier coefficients (verified conditions). The INT-FFT algorithm uses an open-access routine (Suinterp, Seismic Unix) to interpolate the GPR profiles based on seismic trace interpolation. This process uses automatic event identification routines by calculating spatial derivatives to identify discontinuities in space by detecting very subtle changes in the signal, thus allowing for more efficient interpolation without artifacts or signal deterioration. We successfully tested the approach using GPR datasets from the Roman Villa of Horta da Torre (Fronteira, Portugal). The results show an increase in the geometric sharpness of the GPR reflectors and have not produced any numerical artifacts. The tests performed to apply the methodology to GPR-3D data allowed for assessing the interpolation efficiency, the level of recovery of missing data, and the level of information lost when one chooses to increase the distance between profiles in the acquisition stage of the data.

Serotonergic neurons constitute one of the main systems of neuromodulators, whose diffuse projections regulate the functions of the cerebral cortex. Serotonin (5-HT) is known to play a crucial role in the differential modulation of cortical activity related to behavioral contexts. Certain aspects of the 5-HT signaling framework hint at its potential role as a modulator of activity-dependent synaptic changes within the critical period of the primary visual cortex (V1). Cells of the serotonergic system are among the first neurons to differentiate and operate. During postnatal development, ramifications from raphe nuclei become massively distributed in the visual cortical area, remarkably increasing the availability of 5-HT for the regulation of excitatory and inhibitory synaptic activity. A substantial amount of evidence has demonstrated that synaptic plasticity at pyramidal neurons of the superficial layers of V1 critically depends on a fine regulation of the balance between excitation and inhibition (E/I). Therefore, 5-HT could play an important role in controlling this balance, providing the appropriate excitability conditions that favor synaptic modifications. In order to explore this possibility, the present work used in vitro intracellular electrophysiological recording techniques to study the effects of 5-HT on the E/I balance of V1 layer 2/3 neurons, during the critical period. Serotonergic modulation of the E/I balance has been analyzed on spontaneous activity, evoked synaptic responses, and long-term depression (LTD). Our results pointed out that the predominant action of 5-HT implies a reduction of the E/I balance. 5-HT promoted LTD at excitatory synapses while blocking LTD at inhibitory synaptic sites, thus shifting the Hebbian alterations of synaptic strength towards lower levels of E/I balance.

In this paper we use the additive thermodynamic formalism to obtain new bounds of the Hausdorff and box-counting dimension of certain non conformal hyperbolic repellers defined by piecewise smooth expanding maps on a $d$-dimensional smooth manifold $M$.

Flavonoids are widely recognized as natural polydrugs, given their anti-inflammatory, antioxidant, sedative and antineoplastic activities. Recently, different studies have shown that flavonoid have the potential to inhibit BET bromodomains. Previous reports suggest that flavonoids are putative inhibitors of the ZA channel due to their orientation and interactions with P86, V87, L92, L94 and N140. Herein, a comprehensive characterization of the binding mode of the biflavonoid amentoflavone and fisetin is discussed. To this end, both compounds were docked with BRD4 using four docking programs. Results were post-processed with protein-ligand interaction fingerprints. To gain further insights into the binding mode of the two natural products, docking results were further analyzed with molecular dynamics. Results showed that amentoflavone makes numerous contacts in the ZA channel, as previously described for flavonoids and kinase inhibitors. It was also found that amentoflavone can potentially make contacts with non-canonical residues for BET inhibition. Most of these contacts were not observed with fisetin. Based on these results, amentoflavone was tested for BRD4 inhibition, showing activity in the micromolar range. This work may serve as basis for scaffold optimization and further characterization of flavonoids as BET inhibitors.

This article aimed to evaluate, using statistical tools, the generation and composition of urban solid waste (MSW) in the city of Belém, Pará, from nine urban collection sectors in the municipality, and the average nominal income of the population. Approximately 900kg of urban solid waste were col-lected from the municipality in the period from 2021 to 2022. Statistical tests were carried out on hypotheses with 5% significance in comparative evaluations, and their respective average nominal incomes. The results indicated that the organic fraction corresponds to 55.57% of the waste generated in the municipality, 14.26% is inert waste (potentially contaminating) and 0.67% is miscellaneous waste. It was observed that the waste generated by families with high purchasing power tends to contain higher percentages of recyclables, while in families with lower purchasing power the highest percentages tend to be organic. Knowledge of the generation of MSW is fundamental for the choice and dimensioning of operations and processes involved in the management chain at the municipal level. The decentralization of services offered based on solid waste management would enable greater success in serving the population.

The formulation and analytic solution of a new mathematical model with constitutive curvature for analysis of tunnel ventilation shaft wall is proposed. Based on the Mindlin-Reissner theory for thick shells, this model also takes into account the shell constitutive curvature and considers an expression of the shear correction factor variable (αn) in terms of the thickness (h) and the radius of curvature (R). The main advantage of the proposed model is that it has the possibility to analyze thin, medium and thick tunnel ventilation shafts. As a result, two comparisons were made: the first one, between the new model and the Mindlin-Reissner model without constitutive curvature with the shear correction factor (α_n=6/5) as a constant, and the other, between the new model and the tridimensional numerical models (solids and shells) obtained by finite element method for different slenderness ratios (h/R). The limitation of the proposed model is that it is to be formulated for a general linear-elastic and axial-symmetrical state with continuous distribution of the mass.

The dengue virus (DENV) is an arbovirus belonging to the Flaviviridae family; the species comprises four antigenically distinct serotypes (DENV–1, DENV–2, DENV–3, and DENV–4), which are further subdivided into genotypes. The virus is transmitted to humans through mosquito bites, primarily from the Aedes spp. genus. Dengue is endemic in various parts of the world, including tropical and subtropical regions of Asia, Latin America, Africa, and Oceania. In Brazil, the state of Tocantins, located in north-central Brazil, has experienced a significant number of arboviral disease cases, particularly dengue. This study aimed to monitor DENV circulation within the state by conducting full genome sequencing of viral genomes recovered from 61 patients between June 2021 and July 2022. During this period, both DENV-1 and DENV-2 serotypes were identified. Our findings confirm the circulation of DENV serotypes 1 and 2 in Tocantins, affecting males and females equally, with younger age groups (4 to 43 years old) being the most susceptible. Phylogenetic analysis revealed that the circulating viruses belong to DENV–1 genotype V American and DENV–2 genotype III Southeast Asian/American. The Bayesian analysis of DENV-1 Genotype V sequenced here is closely related to genomes previously sequenced in the state of São Paulo. Regarding DENV-2 genotype III genomes, these are clustered in a distinct, well-supported subclade, along with previously reported isolates from the states of Goiás and São Paulo. In both cases, our results suggest that multiple introductions of these genotypes occurred in the Tocantins state. This observation highlights the significant impact of major population centers in Brazil on virus dispersion, including other Latin-American countries and the USA. In the SNP analysis, DENV-1 displayed 122 distinct missense mutations, while DENV-2 had 44, with significant mutations predominantly occurring in the envelope and NS5 proteins. The analyses performed here reveal the concomitant circulation of distinct DENV-1 and -2 genotypes in some Brazilian states, underscoring the dynamic evolution of the DENV and the ongoing significance of surveillance efforts in supporting public health policies.

All types of sports are potential application scenarios for automatic and real-time visual object and event detection. In rink hockey, the popular roller quad skate variant of hockey team sports, it is of great interest to automatically track player’s movements and positions, player’s sticks and, also, making other judgments, such as being able to locate the ball. In this work, we introduce a real-time pipeline composed by an object detection model, created specifically for rink hockey games, followed by a knowledge-based event detection module. Even in the presence of occlusions and quick motions, our deep learning object detection model effectively identifies and tracks, in real-time, important visual elements such as: ball; players; sticks; referees; crowd; goalkeeper; and goal. Using a curated dataset composed by a collection of videos of rink hockey, comprising 2525 annotated frames, we trained and evaluated the algorithm performance and compare it to state of the art object detection techniques. Our object detection model, based on YOLOv7, presents a global accuracy of 80%, and presents a good performance in terms of accuracy and speed, according to our results, making it a good choice for rink hockey applications. In our initial tests, the event detection module successfully detected one important event type in rink hockey games, the occurrence of penalties.

This document presents, from environmental thinking (ecosystem - culture relations), the concept of the Main Agroecological Structure of Agroecosystems (MAS, EAP, for its acronym in Spanish), considered as a dissipative cultural structure. It discusses its possible applications (resilience, production, diversity) both inside and outside the farms. The MAS can be useful in the land planning on the farms, based on the concept of potential MAS that allows the quantification of the management of internal and external corridors, including natural vegetation. At the same time, it can be useful in the context of landscape management because it shows a series of cultural relations (economic, social, symbolic and technological) hidden from the partial analysis of landscape ecology.

In this work we discuss the insights from activity landscape, docking and molecular dynamics towards the understanding of the structure-activity relationships of dual inhibitors of major epigenetic targets: lysine metiltransferase (G9a) and DNA metiltranferase 1 (DNMT1). The study was based on a novel data set of 50 published compounds with reported experimental activity for both targets. The activity landscape analysis revealed the presence of activity cliffs, e.g., pairs of compounds with high structure similarity but large activity difference. Activity cliffs were further rationalized at the molecular level by means of molecular docking and dynamics simulations that led to the identification of interactions with key residues involved in the dual activity or selectivity with the epigenetic targets.

This study examines the potential of combining decision support approaches to identify optimal bundles of ecosystem services. A forested landscape, Zona de Intervenção Florestal of Paiva and Entre-Douro and Sousa (Portugal), is used to test and demonstrate this potential. The landscape extends over 14,000 ha, representing 1,976 stands. The property is fragmented into 376 holdings. The overall analysis was performed in three steps. First, we selected six alternative solutions (A to F) in a Pareto frontier generated by a multiple criteria method within a decision support system (SADfLOR) for subsequent analysis. Next, an aspatial strategic multi-criteria decision analysis (MCDA) analysis was performed with the Criterium DecisionPlus (CDP) component of another decision support system (EMDS) to assess the aggregate performance of solutions A to F for the entire forested landscape with respect to their utility for delivery of ecosystem services. For the CDP analysis, SADfLOR data inputs were grouped into two sets of primary criteria: Wood Harvested and Other Ecosystem Services. Finally, a spatial logic-based assessment of solutions A to F for individual stands of the study area was performed with the NetWeaver component of EMDS. The NetWeaver model was structurally and computationally equivalent to the CDP model, but the key NetWeaver metric is a measure of the strength of evidence that solutions for specific land stands were optimal for the unit. Solutions D and B performed best in the aspatial strategic MCDA analysis, and a composite of the maps generated by NetWeaver demonstrated the spatial basis for the performance of solutions D and B in individual land stands. We conclude with a discussion of how the combination of decision support approaches encapsulated in the two systems could be further automated.

Bone cement, mainly based in PMMA, is commonly used in different arthroplasty surgical proce-dures, and its use is essential for prosthesis fixation. However, its manufacturing process reaches high temperatures that can produce necrosis in the patients' surrounding tissues. In order to con-tribute to avoid this problem, the addition of graphene could delay the polymerisation of the MMA and, simultaneously, contribute to the optimisation of the composite material's properties. This article analysed the effect of the addition of different percentages of Highly Reduced Graphene Oxide (HRGO) with different wt. % (0,10, 0,50 and 1,00) and surface densities (150, 300, 500 and 750 m2/g) on the physical, mechanical, and thermal properties of commercial PMMA-based bone cement and its processing. It was noticed that a lower sintering temperature would be reached with this addition, making it less harmful to use in surgery and as it reduces its adverse effects. In contrast, the materials' density does not show significant changes, which indicates that the addi-tion of HRGO does not significantly increase its porosity. Lastly, the mechanical properties are re-duced by almost 20 %. Nevertheless, these properties are high enough so that these new materials can still fulfil their structural function.

Integrated crop-livestock production (ILP) is an interesting alternative for more sustainable soil use. However, more studies are needed to analyze soil pore properties under ILP at the micrometer scale. Thus, this study proposes a detailed analysis of soil pore architecture at the micrometer scale in three dimensions. For this purpose, samples of an Oxisol under ILP subjected to minimum tillage (MT) and no-tillage (NT) with ryegrass as cover crop (C) and silage (S) were investigated. The soil micromorphological properties of the soil were analyzed using X-ray microtomography. The MT(C) system showed the highest values of porosity (c. 20.4%), connectivity (c. 32.8×103), volume (c. 26%), and number of pores (c. 32%) in a rod-like shape. On the other hand, the MT(S), NT(C), and NT(S) systems showed higher tortuosities (c. 2.2, c. 2.0, and c. 2.1) and lower pore connectivities (c. 8.3×103, c. 6.9×103, and c. 6.2×103), especially in S use. Ellipsoidal and rod-shaped pores predominated over spheroidal and disc-shaped pores in all treatments. The results of this study show that the use of ryegrass as a cover crop improves soil physical properties, especially in MT. For S use, the type of soil management (MT or NT) did not show any differences.

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

The determination of the parameters that characterise the air-void system in hardened concrete elements becomes crucial for structures under freezing and thawing cycles. The ASTM C457 standard describes some procedures to accomplish this task, but they are not easy to apply, require specialised equipment such as a stereoscopic microscope and result in highly tedious tasks to be performed. This paper describes an alternative procedure to the modified point-count method described in the Standard that makes use of macro photography. This alternative procedure is successfully applied to a large set of samples and presents some advantages over the traditional method, since the required equipment is less expensive and provides a more comfortable and less tedious procedure for the operator.

Background: Coronary artery bypass grafting (CABG) can be performed using on-pump or off-pump techniques. The optimal approach remains debated. Objectives: The COMPARE CABG (Comparative Outcomes of Mortality, Perioperative complications, cARdiac function, and Hospital stay in On-Pump versus Off-Pump Coronary Artery Bypass Grafting) study aims to systematically compare the outcomes of these surgical approaches. Methods: A comprehensive search was conducted in Pubmed, Cochrane Library, and other databases. Studies with a sample size > 4000 were included. Outcomes analyzed included mortality, complications, cardiac function, and hospital stay. Results: Meta-analysis of 5 studies with 58,232 patients showed that off-pump CABG was associated with a slightly lower complication rate: 15% for on-pump CABG and 13.5% for off-pump CABG with a pooled effect size of 0.90 (95% CI: 0.85-0.95). In terms of cardiac function and hospital stay, results were also favorable to off-pump CABG with an effect size of 1.12 (95% CI: 1.05-1.19) and 1.15 (95% CI: 1.10-1.20), respectively. The pooled mortality rate was 2.5% for on-pump and 2.4% for off-pump CABG, with an effect size of 1.05 (95% CI: 0.98-1.12), indicating no significant difference between the groups. Conclusion: These findings suggest that off-pump CABG may be a preferable option for reducing surgical complications, though both techniques yield comparable mortality outcomes. Further research is needed to explore long-term cardiac function and patient-specific factors influencing the choice of surgical method.

The literature is scarce in the evaluation of Behçet’s disease (BD) among individuals during the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection. Then, an epidemiological study was conducted using the data from 46 hospitalized patients with BD and coronavirus disease (COVID)-19 representing a prevalence of 2,11 patients per 100,000 inhabitants. From the study sample, 58.7% (27 patients) were female, and 67.4% (31 patients) were White. The main symptoms were fever (40; 87.0%), cough (38; 82.6%), dyspnea (35; 76.1%), and peripheral saturation below 95% (35%, 76.1%). The need for intensive care unit support occurred for 39.1% (18) patients. Also, 21.7% (10) patients needed invasive ventilatory support and 47.8% (22) needed non-invasive ventilatory support. A total of 73.9% (34) of patients lived, and 26.1% (12) of patients died. Only the presence of respiratory discomfort [37.9% vs. 5.9%] was more common among those who died. Patients with BD were not at an increased risk of worse COVID-19 outcomes in Brazil.

Medicinal plants for bone grafts are promising because they are free from infecting microorganisms and biocompatible. We report a novel study evaluating osteoregeneration of bone grafts from extracts of Alternanthera brasiliana and Fridericia platyphylla after bone injury induced by radius fracture in rats. Grafts were obtained using 2% chitosan gel and 0.5% hydroalcoholic extract. The rats were randomly divided into four experimental groups (N= 12): Negative control (NC) - Chitosan gel; Positive control (PC) - bovine mineral bone graft (Lumina Bone®, fine powder 0.5); F. platyphylla Graft (FRID) - 0.5% bone graft; A. brasiliana Graft (ABRA) - 0.5% bone graft. The animals were evaluated for three periods, 30, 60, and 90 days after fracture induction. Bone alkaline phosphatase (BSAP) and radiographic and histological evaluations were followed. After 90 days, there was an increase in BSAP for the ABRA group on the newly formed bone matrix but not for FRID, indicating the presence of active osteoblasts. Additionally, mature bone tissue and bone remodeling were observed, and a conspicuous presence of type I collagen for both FRID and ABRA. We demonstrated that FRID and ABRA grafts produced early bone neoformation. New perspectives for these species as a graft are suggested.

As companies increasingly undergo digital transformation, the role of talent management pro-cesses becomes pivotal in enhancing overall organizational performance. The research addresses the significance of talent management in corporate digital transformation, examining whether variations in the digitalization of these processes can be attributed to company size. A qualitative approach was employed, utilizing a questionnaire, collecting responses from 202 organizations across diverse sectors. Findings reveal disparities in digitalization throughout the talent man-agement process, with pronounced presence in the attracting, selecting, and rewarding phases, but diminishing in deployment and development, further declining in planning. A positive cor-relation between company size and adoption of specific digital platforms was observed. Larger enterprises exhibit greater utilization of digital platforms in talent deployment and development. Moreover, corporate communication tools are consistently utilized in the rewarding phase, irre-spective of company size. These findings offer practical insights for organizations to optimize their digitalization strategies based on their scale, thereby contributing to more effective and tailored digitalization endeavors. The uniqueness of this research lies in its exploration of the in-fluence of company size on the digitalization of talent management processes and its potential to explain variations across different stages of these processes.

Having garnered significant attention in the scientific community over the past decade, Wire Arc Directed Energy Deposition (arc-DED) technology is at the heart of this investigation into additive manufacturing parameters. Singularly focused on invar as the selected material, the primary objective revolves around devising an indirect cord height measurement approach. This innovative methodology involves the seamless integration of internal signals and sensors, enabling the derivation of crucial measurements sans the requirement for direct physical interaction or conventional measurement methodologies. Through the course of this research, meticulous alteration of deposition parameters is undertaken to thoroughly scrutinize their influence on the ultimate cord dimensions. The fusion of cutting-edge manufacturing techniques with advanced sensor technology constitutes the essence of this endeavor, offering substantial potential to augment precision and efficiency in additive manufacturing processes. Remarkably cost-effective, this solution circumvents the need for intricate measurements and significantly contributes to the proper layer-by-layer growth process.

Several clinically useful anticancer drugs selectively kill cancer cells by inducing DNA damage; the genomic instability and DNA repair defects of cancer cells make them more vulnerable than normal cells to the cytotoxicity of DNA-damaging agents. Because epoxide-containing compounds can induce DNA damage, we have used the MTT assay to evaluate the selective cytotoxicity of three epoxyalkyl galactopyranosides against A549 lung cancer cells and MRC-5 lung normal cells. Compound (2S,3S)-2,3-Epoxydecyl 4,6-O-(S)-benzylidene-β-D-galactopyranoside (EDBGP) showed the highest selective anticancer activity and was selected for mechanistic studies. After observing that EDBGP induced cellular DNA damage (comet assay), we found that cells deficient in nucleotide excision repair were hypersensitive to the cytotoxicity of this compound; this suggests that EDBGP may induce bulky DNA adducts. EDBGP did not inhibit glycolysis (glucose consumption and lactate production). Pre-treatment of lung cancer cells with several antioxidants did not reduce the cytotoxicity of EDBGP, thereby indicating that reactive oxygen species do not participate in the anticancer activity of this compound. Finally, EDBGP was screened against a panel of cancer cells and normal cells from several tissues, including three genetically modified skin fibroblasts with increasing degree of malignancy. Our results suggest that epoxyalkyl galactopyranosides are promising lead compounds for the development of new anticancer agents.

Psychotherapy is one of the evidence-based clinical interventions for the treatment of depression in older adults with dementia. Randomized Controlled Trials are often the first methodological choice to gain evidence, yet they are not applicable to a wide range of humanistic psychotherapies. Amongst all, the efficacy of the Gestalt therapy (GT) is under-investigated. The purpose of this paper is to present a research protocol aiming to assess the effects of a GT-based intervention on people with dementia (PWD) and the indirect influence on their family carers. The study implements the Single-Case Experimental Design with Time-Series Analysis that will be carried out in Italy and Mexico. Ten people in each country, who received a diagnosis of dementia and present depressive symptoms, will be recruited. Eight or more GT sessions will be provided whose fidelity will be assessed by the GT Fidelity Scale. Quantitative outcome measures are foreseen for monitoring participants’ depression, anxiety, quality of life, carers’ burden, and the caregiving dyad mutuality, at baseline and follow-up. The advantages and limitations of the research design are considered. If GT will result effective in the treatment of depression in PWD, it could enrich the range of evidence-based interventions provided by healthcare services.

Fake news was conventionally assumed to mean fabricated information published in newspapers and other mass media. It was mostly done to increase the paper's sales and was unlikely to have long-term impacts on society. Fake news in marketing concerns intentionally delivering false or misleading information regarding a product or service to influence consumer behavior. Despite the severity of these impacts, we noted that there is very little scientific research on fake news in marketing and consumer behavior. This systematic literature review (LRSB) aims to bridge this knowledge gap by searching and analysing relevant publications on "fake news in marketing" and synthesising data from 117 relevant studies, providing a framework for marketers and business leaders to reduce the spread and impact of online misinformation. The main highlights identify that the implementation and use of social media, shaping a presence on the internet, diffusion, and consumption of fake news have become a serious challenge and a dominant problem in the marketing sector, especially with the growth of digital marketing. Strategically, fake news spread can be categorized into various types, and the use of these tactics can produce short-term benefits such as increased engagement and instant sales, but they can also have severe long-term costs such as reputational damage, loss of revenues and market share, and discouraged investors and shareholders.

Tumors of the central nervous system produce adverse outcomes in everyday life; however, low-grade gliomas are uncommon in adults. For this reason, the objective is to describe the executive function of a 59-year-old adult neuro-oncological patient. Pre- and postintervention evaluation of neurological and neuropsychological functioning was performed through neuroimaging techniques (iRM, Spectroscopy, Electroencephalography), hospital history, psychological interview, and Wisconsin Card Classification Test (WCST). Executive performance exhibited a noticeable decline in typical and centile WCST results, as evidenced by deterioration in persistent scores, failure to maintain an attitude and difficulty learning from clinical samples. This information coincides with the evolution of the neuroimage over time. Finally, this topic is discussed in the literature.

In this work, the influence of catalyst reuse and reaction time on the yield and quality of organic liquid products (OLP) obtained in a cracking pilot plant at 450 °C and 1.0 atm has been systematically investigated. The distillation of OLP produced 04 (four) distilled fractions. The quality of the biofuels was certified by physical-chemical analysis, as well as FT-IR and GC-MS analysis. The experimental results showed the feasibility of applying the spent sodium carbonate twice in catalytic cracking of vegetable oils. The physical-chemical properties (density, viscosity, acid value, saponification value, and flash point) of OLP decrease as the reaction time increases. The distillation of OLP yields 62.35% (wt.), producing green-like gasoline, kerosene, and diesel fractions rich in hydrocarbons. Therefore, biofuels-like fractions produced by distillation of OLP have a great potential for replacing partially petroleum derived fuels.

Chiral hydroxamic acid (HA) and bis-hydroxamic acid (BHA) ligands have made significant contributions to the field of asymmetric synthesis, particularly in the synthesis of natural products. These ligands possess unique molecular structures that allow for exceptional stereochemical control, leading to their widespread use in catalytic systems. This review highlights the advancements made in asymmetric synthesis using chiral hydroxamic acid and bis-hydroxamic acid ligands and their impact on the synthesis of complex natural products. The discussion encompasses their role in enantioselective C-C bond formation, the functionalization of C-H bonds, asymmetric transformations involving heteroatoms, and their application in the total synthesis of natural products. The versatility and efficiency of chiral hydroxamic acid ligands and bis-hydroxamic acid ligands make them invaluable tools for synthetic chemists working towards the efficient and selective synthesis of natural products. This review provides a comprehensive overview of their contributions, showcasing their potential to expand the boundaries of chemical synthesis and access the diverse array of natural product scaffolds.

Porphyry copper-molybdenum deposits (PCDs) are the world’s most important source of copper, molybdenum and rhenium. Previous studies have reported that some PCDs can have sub-economic to economic grades of critical metals, i.e., those elements that are both essential for modern societies and subject to the risk of supply restriction (e.g., platinum group elements (PGE), rare earth elements (REE), In, Co, Te, Ge, Ga, among others). Even though some studies have reported measured concentrations of Pd and Pt in PCDs, their occurrence and mineralogical form remain poorly constrained. Furthermore, these reconnaissance studies have focused predominantly on porphyry Cu-Au deposits, but very limited information is available for porphyry Cu-Mo systems. In this contribution, we report the occurrence of critical metal (Pd, Pt, Au, Ag, and Te) inclusions in copper sulfides from the world’s largest PCD, the supergiant Río Blanco-Los Bronces deposit in central Chile. Field emission scanning electron microscope (FESEM) observations of chalcopyrite and bornite from the potassic alteration zone reveal the presence of micro- to nano-sized particles (<1-10 μm) of noble metals, most notably Pd, Au, and Ag. The high-resolution data show that these inclusions are mostly tellurides, such as merenskyite [PdTe2], Pd-rich hessite [Ag2Te], sylvanite [(Ag, Au)Te2] and petzite [Ag3AuTe2]. The data point to Pd (and probably Pt) partitioning in copper sulfides during the high-temperature potassic alteration stage, opening new avenues of research aimed at investigating not only the mobility of PGE during mineralization and partitioning into sulfides, but also at evaluating the potential of porphyry Cu-Mo deposits as a source for noble metals.

This paper analyses the evolution of the internal damage in two types of steel that show different fracture behaviours, with one of them being the initial material used for manufacturing prestressing steel wires, which shows a flat fracture surface perpendicular to the loading direction, and the other one being a standard steel used in reinforced concrete structures, which shows the typical cup-cone surface. 3mm-diameter cylindrical specimens are tested with a tensile test carried out in several loading stages and, after each of them, unloaded and analysed with X-ray tomography, which allows detection of internal damage throughout the tensile test. In the steel used for reinforcement, damage is developed progressively in the whole specimen, as predicted by Gurson-type models, while in the steel used for manufacturing prestressing steel-wire damage is developed only in the very last part of the test. In addition to the experimental study, a numerical analysis is carried out by means of the finite element method by using a Gurson model to reproduce the material behaviour.

We recently screened a series of new aziridines β-D-galactopyranoside derivatives for selective anticancer activity and identified 2-methyl-2,3-[N-(4-methylbenzenesulfonyl)imino]propyl 2,3-di-O-benzyl-4,6-O-(S)-benzylidene-β-D-galactopyranoside (AzGalp) as the most promising compound. In this article, we explore possible mechanisms involved in the cytotoxicity of this aziridine and evaluate its selective anticancer activity using cancer cells and normal cells from a variety of tissues. Our data show that AzGalp induces DNA damage (detected with the comet assay). Cells deficient in the DNA repair pathway nucleotide excision repair (NER) were hypersensitive to the cytotoxicity of this compound. These results suggest that AzGalp induces bulky DNA adducts, and that cancer cells lacking a functional NER pathway may be particularly vulnerable to the anticancer effects of this aziridine. Several experiments revealed that neither the generation of oxidative stress nor the inhibition of glycolysis played a significant role in the cytotoxicity of AzGalp. The combinations of AzGalp with either oxaliplatin or 5-fluorouracil slightly improved the ability of both anticancer drugs to selectively kill cancer cells. AzGalp also displayed selective cytotoxicity against a panel of malignant cells versus normal cells; the highest selectivity was observed for two acute promyelocytic leukemia cell lines. Additional preclinical studies are necessary to evaluate the anticancer potential of AzGalp.

Changes brought about by the Internet to Scholarly Communication and the spread of Open Access movement, have made it possible to increase the number of potential readers of published research dramatically. This two-phase study aims, at first, to assert the satisfaction of the potential for increased open access to articles published by authors at the University of Coimbra, in a context when there was no stimulus for the openness of published science other than an institutional mandate set by the University policy on Open Access (“Acesso Livre”). The satisfaction of the access openness was measured by observing the actual archiving behavior of researchers (either directly or through their agents). We started by selecting the top journal titles used to publish the STEM research of the University of Coimbra (2004-2013) by using Thomson Reuters’ Science Citation Index (SCI). These titles were available at the University libraries or through online subscriptions, some of them in open access (21%). By checking the journals' policy at the time regarding self-archiving at the SHERPA/RoMEO service, we found that the percentage of articles in Open Access (OA) could rise to 80% if deposited at Estudo Geral, the Institutional Repository of the University of Coimbra, as prescribed by the Open Access Policy of the University. As we concluded by verifying the deposit status of every single paper of researchers of the University that published in those journals, this potential was far from being fulfilled, despite the existence of the institutional mandate and favorable editorial conditions. We concluded, therefore, that an institutional mandate was not sufficient by itself to fully implement an open access policy and to close the gap between publication and access. The second phase of the study, to follow, will rescan the status of published papers in a context where the Portuguese public funding agency, the Fundação para a Ciência e a Tecnologia, introduced in 2014 a new significant stimulus for open access in science. The FCT Open Access Policy stipulates that publicly funded published research must be available as soon as possible in a repository of the Portuguese network of scientific repositories, RCAAP, which integrates the Estudo Geral.

This study takes as a starting point the importance and dependence of the media (Ball-Rokeach & DeFleur, 1976) to obtain information about the pandemic. The dependency theory of the media system was developed in the 1970s when mass media were the dominant source of information. Today, at a time when media choices have become abundant, studies are needed to understand the phenomenon of media dependence in light of new dimensions made important by the transformations that have taken place in the social and media fields - where the coexistence of mass media with social media platforms stands out. As large-scale crises rarely occur and the media environment changes rapidly, it is important to analyze how media dependence relates to choose and trust in different media (traditional media vs. social media) in times of crisis. Several questions arise. What is the trust attributed by individuals to social media as sources of information about the COVID-19? How well informed are the individuals who choose these sources as the main sources of information? From a questionnaire administered to 240 individuals in Portugal, during the first week of the state of emergency (March 2020), this research seeks to identify how people gained access to information about the COVID-19, how they acted critically towards the various sources and how they assess the reliability of different media. Finally, it analyzes the association between the type of medium chosen and adherence to misinformation content about the virus. The results reveal the existence of a phenomenon of dependence on the media, with a strong exposure (both active and accidental) to informative content, with conventional media being privileged as the main source, and positively distinguished in terms of confidence. Finally, a statistically significant association of a positive sign was identified between the use of social media as the main source and the acceptance of misinformation.

(1) Background: Franco’s dictatorship was an authoritarian regime in Europe in the twentieth century. The political and historical context has a significant influence on the socio-cultural make-up of each era, having consequences on equality and violence against women. The objec-tive of our study is to explore and understand women’s experiences of violence against women during the Franco regime and how it affects them today; (2) Methods: This qualitative study ex-plores violence against women in Francoist Spain. Data was colleted between January and march 2022 through twenty-one interviews were carried out with female survivors of Francoism; (3) Results: Three themes emerged from the analysis: underlying social conditions that allow for vio-lence against women; forms of violence against women: from punishment to forced silence; dif-ferent standpoints about violence against women: the feminist struggle versus denial; (4) Conclu-sions: We concluded that the imposed patriarchy during Francoist repression was harmful for Spanish women for decades. Women suffered violence against women and they are still bearing the consequences, passing on attitudes that could contribute to the persistence of violence against women.

The main purpose of this paper is to present a system to detect extrusion failures in Fused Deposition Modelling (FDM) 3D printers by sensing that the filament is moving forward properly. After several years using these kind of machines, authors detected that there is not any system to detect the main problem in FDM machines. Authors thought in different sensors and used the Weighted Objectives Method, one of the most common evaluation methods, for comparing design concepts based on an overall value per design concept. Taking into account the obtained scores of each specification, the best choice for this work is the optical encoder. Once the sensor is chosen, it is necessary to design de part where it will be installed without interfering with the normal function of the machine. To do it, photogrammetry scanning methodology was employed. The developed device perfectly detects the advance of the filament without affecting the normal operation of the machine. Also, it is achieved the primary objective of the system, avoiding loss of material, energy and mechanical wear, keeping the premise of making a low-cost product that does not significantly increase the cost of the machine. This development has made it possible to use the printer with remains coil filament, which were not spent because they were not sufficient to complete an impression and also printing models in two colours with only one extruder.

This paper conducts an extensive literature review focusing on the utilisation of crack tip plasticity as a crucial parameter in determining and enhancing crack growth models. The review encompasses a comprehensive analysis of various methodologies, predominantly emphasising numerical simulations of crack growth models while also considering analytical approaches. Although experimental investigations are not the focus of this review, their relevance and interplay with numerical and analytical methods are acknowledged. The paper critically examines these methodologies, providing insights into their advantages and limitations. Ultimately, this review aims to offer a holistic understanding of the role of crack tip plasticity in the development of effective crack growth models, highlighting the synergies and gaps between theoretical, experimental, and simulation-based approaches.

The introduction of non-conventional renewable energies (photovoltaic and wind, in the residential case) demand new proposals and opportunities to obtain a domestic energy management system (HEMS), which allows reducing the use of electrical energy. The HEMS incorporates artificial intelligence (AI) techniques to respond to energy demand (DR), which can control, switch, turn on and off, modifying the consumption profile, reducing monthly billing, which as a consequence brings improvement. of the quality of life at home. Based on what has been described, a model for identifying electrical appliances and determining consumption patterns for the home is proposed, using intrusive measurement/actuator equipment called Smart Socket. The Smart Socket measures the electrical variables of voltage and current in real time, calculating the powers and active-reactive-apparent energies of each household appliance (or the most relevant ones). The information provided by the Smart Socket is used as a basis to configure the HEMS, with the aim of optimizing energy use using artificial intelligence techniques and tools, thus reducing energy consumption, CO2 emissions and the user's monthly billing. residential.

In this study, the analysis of metals in the solubilized extract of the organic fraction of Urban Solid Waste (MSW) from the municipality of Belém do Pará was carried out. The waste used in this research was collected in residential areas, through door-to-door collection, with the points and neighbor-hoods served in the municipality of Belém determined by the sectorization of these locations, with family income as the main parameter. The MSW was collected and transported to the segregation area. Gravimetric analysis of MSW was carried out and the selected organic and paper fractions were subjected to drying, crushing and sieving pre-treatment. Next, the solubilized extract of the organic fraction of MSW was obtained, following the method set out in NBR nº 10.006/2004 of the Brazilian Association of Technical Standards. The values obtained were compared with CONAMA Resolutions nº 357/2005, 396/2008 and 430/2011, in addition to being compared with results of bibliographical research. The results indicated that these wastes do not comply with environmental and health regulations. Although a highly significant association was found between chromium and boron through Pearson's correlation, the remaining strong correlations between other elements did not reach statistical significance. Furthermore, a similarity was observed in the solubilization conditions of these wastes with those found in landfill leachate.

.Cloud manufacturing is an evolving networked framework that enables multiple manufacturers to collaborate in providing a range of services, including design, development, production, and post-sales support. The framework operates on an integrated platform encompassing a range of Industry 4.0 technologies, such as Industrial Internet of Things (IIoT) devices, cloud computing, Internet communication, big data analytics, artificial intelligence, and blockchains. The connectivity of industrial equipment and robots to Internet opens the cloud manufacturing to the massive attack surface of cybersecurity and cyber crime threats caused by external and internal attackers. The impacts can be severe because physical infrastructure of industries is at stake. One potential method to deter such attacks involves utilizing blockchain and artificial intelligence to track the provenance of IIoT devices. This research explores a practical approach to achieve this goal by gathering provenance data associated with operational constraints defined in smart contracts and identifying deviations from these constraints through predictive auditing using artificial intelligence. A software architecture comprising IIoT communications to machine learning for comparing the latest data with the predictive auditing outcomes and logging appropriate risks was designed, developed, and tested. The state changes in the smart ledger of smart contracts were linked with the risks such that the blockchain peers can timely detect high deviations and take actions. The research defined the constraints related to physical boundaries and weight lifting limits allocated to three forklifts and showcased the mechanisms of detecting risks of breaking these constraints with the help of artificial intelligence. It also demonstrated state change rejections by blockchains at medium and high-risk levels. This research followed software development in Java 8 using JDK 8, CORDA blockchain framework, and Weka package for random forest machine learning. As a result of this, the model, along with its design and implementation, has the potential to enhance efficiency and productivity, foster greater trust and transparency in the manufacturing process, booster risk management, strengthen cybersecurity, and advance sustainability efforts.

Introduction: Left ventricular dysfunction in an independent predictor of mortality in Chagas disease. Global longitudinal strain (GLS) is an emerging echocardiographic modality with possible incremental value in early detection of cardiac involvement. Objective: Compare left ventricular function with multiple echocardiographic parameters between patients with the indeterminate and chronic forms of Chagas and perform a literature review. Methods: In this observational study, 11 patients with a confirmed diagnosis of Chagas disease were evaluated. Individuals were distributed as follows: 5 with the indeterminate and 6 with the chronic forms. Conventional echocardiographic evaluation was followed by GLS measurement. Results: The mean left ventricle ejection fraction LVEF was 33 ± 2.88 and the mean GLS of the left ventricle was - 10.76 ± 2.20 in the chronic form as compared to 57.80 ± 6.49 and - 17.34 ± 3.82, respectively in the indeterminate group. Contractility was reduced in segments of the inferior, inferoseptal and anteroseptal walls in both groups. Conclusion: Analysis of longitudinal strain in the indeterminate form has potential incremental value to the conventional analysis of ejection fraction when compared to patients with chronic Chagas cardiomyopathy, especially with individual segmental analysis but the impact and clinical significance of these techniques is still unknown.

Introduction: The disease caused by Coronavirus-2019 (COVID-19) was initially described in December 2019. Severe acute respiratory syndrome type 2 (Sars-Cov-2) is responsible for an important multisystem inflammatory spectrum. Cardiovascular conditions have been reported with an estimated frequency of 8-28%. In this context, transthoracic echocardiography associated with the analysis of the two-dimensional Global Longitudinal Strain (GLS) of the left ventricle derived from Speckle Tracking emerges as a promising modality. Objective: This study aims to evaluate the applicability of GLS and segmental deformity assessment in detecting subclinical myocardial dysfunction in patients that recovered from COVID-19 infection. Methods: The observational study involved 18 patients (mean age 52 years) with recent evidence of COVID-19 infection that underwent detailed echocardiographic evaluation with GLS, and cardiac magnetic resonance (CMR) according to segmental assessment results. The degree of correlation between the methods was analyzed and a systematic literature review was also conducted. Results: The mean left ventricular ejection fraction (LVEF) was 57.50 ± 9.98%. Only 16.6% of patients had reduced LVEF. The average GLS was – 18.70 ± 3.54% and in 44% of cases only one myocardial segment was affected, particularly the inferolateral basal. CMR revealed inflammatory cardiomyopathy. Discussion: Subclinical myocardial involvement is associated with major adverse cardiac events. Literature review supports the use of GLS for detecting early cardiac involvement. Conclusion: Speckle-tracking echocardiography has been shown to have clinical utility in a variety of settings and to offer superior prognostic value with a potential to enhance subclinical detection of myocardial changes in patients after COVID-19 infection.

As consequence of the digital transformation, e-learning methodologies have become an inseparable part of the standard classes in schools and universities, assuming an increasingly significant role in compensating for the difficulties resulting from the COVID-19 pandemic. Numerous pedagogical methodologies and strategies can be easily implemented in high education, promoting students’ motivation and interest in learning. This research study analyses the implementation of gamification pedagogical strategy on 50-60 undergraduate chemical engineering students at the university, by evaluating its effect on the success rate on a specific topic of Chemical Reactions Engineering subject and the motivation effect for the following topics. Our results show a significant positive effect of the gamification strategy on university lectures, increasing up to 25-30 % of the success ratio with an apparent motivation effect. During the subsequent years, the changes in the lifestyle of study also play a role in students’ performance. Therefore, it is necessary to evaluate case studies such as the one presented here to understand better the use of these pedagogical methods and strategies in high education, especially in technical subjects described in this paper.

This paper proposes an upper bound for mine productivity and also a simple truck dispatch rule that demonstrates how tight the upper bound can be using simulation. It also proposes a greedy search to approximate the productivity upper bound, which is faster and often exact. Uncertainty is added to the simulation in order to verify how the productivity responds to it. Typically, the productivity upper bound is less tight close to its saturation point as a function of the number of trucks, where adding more trucks only increases queues. Furthermore, more uncertainty in the model typically leads to a less tight upper bound. The results are conducted using real data from an open pit mine in Brazil.

Background/Objectives: Managing chronic respiratory diseases such as asthma and chronic obstructive pulmonary disease (COPD) within the Spanish Sistema Nacional de Salud (SNS) presents significant challenges, particularly due to their high prevalence and poor disease control rates—approximately 45.1% for asthma and 63.2% for COPD. This study aims to develop a novel predictive model using Electronic Health Records (EHR) to estimate the likelihood of poor disease control in these patients, thereby enabling more efficient management in primary care settings. Methods: The Seleida project employed a bioinformatics approach to identify significant clinical variables from EHR data in primary care centers in Seville and Valencia. Statistically significant variables were incorporated into a logistic regression model to predict poor disease control in patients with asthma and COPD patients. Key variables included the number of short-acting β-agonist (SABA) and short-acting muscarinic antagonist (SAMA) canisters, prednisone courses, and antibiotic courses over the past year. Results: The developed model demonstrated high accuracy, sensitivity, and specificity in predicting poorly controlled disease in both asthma and COPD patients. These findings suggest that the model could serve as a valuable tool for the early identification of at-risk patients, allowing healthcare providers to prioritize and optimize resource allocation in primary care settings. Conclusions: Integrating this predictive model into primary care practice could enhance the proactive management of asthma and COPD, potentially improving patient outcomes and reducing the burden on healthcare systems. Further validation in diverse clinical settings is warranted to confirm the model's efficacy and generalizability.

Although monitoring and observing insect pest populations in the fields is essential in crop management, it is still a laborious and sometimes ineffective process. High infestation levels may diminish the photosynthetic activity of soybean plants, affecting their development and reducing the yield. An imprecise decision making in integrated pest management program may lead to an ineffective control in infested areas or the excessive use of insecticides. In order to reach a more efficient control of arthropods population it is important to evaluate the infestation in time to mitigate its negative effects on the crop and remote sensing is an important tool for monitoring. It was proposed that infested soybean areas could be identified, and the arthropods quantified from non-infested areas in a field by hyperspectral remote sensing. Thus, the goals of this study were to investigate and discriminate the reflectance characteristics of soybean non-infested and infested with Bemisia tabaci using hyperspectral remote sensing data. Therefore, samples of infested and non-infested soybean leaves were collected and transported to the laboratory to obtain the hyperspectral curves. The results obtained allowed to discriminate the different levels of infestation and to separate healthy from whitefly infested soybean leaves based on their reflectance.

This work seeks to approach the comparative analysis of the distribution of POFs (polymeric optical fibers) arranged in a random and sorted manner in the manufacture of translucent concretes. The following characteristics were analyzed: compressive strength, flexural tensile strength, capillary water absorption and light transmittance. Portland cement, water, fine aggregate (sand), silica fume, polycarboxylate ether-based superplasticizer and polymeric optical fiber were used in the production of the composites. Except the fiber content, the mixture of all other inputs was kept as a fixed parameter. Groups with the following levels of POFs were produced: 0%, 2%, 3.5% and 5%. The POF content is the sum of the areas of the fiber sections in the composite with the total area of the translucent surface. The results showed that for the analysis of mechanical behavior (flexural tensile and compressive strength) and durability (capillary water absorption), composites with random and sorted fibers within the 2% POF presented to belong to statistically distinct groups. For the other fiber contents, there was no pattern of behavior, that is, it cannot be said that there is a difference within 3.5% or 5% POF between sorted and random fibers in relation to the mechanical and durability characteristics analyzed. As for the light transmittance, it was attributed that the statistical difference between the fiber arrangements only within the 5% POF content can be a consequence of their accumulation in certain points of the material, thus influencing this characteristic measured by a light meter.

A strategy to reduce qualitative and quantitative losses in crop-yields refers to early and accurate detection of insect-damage caused in plants. Remote sensing systems like hyperspectral proximal sensors are a promising strategy for managing crops. In this aspect, machine learning predictions associated with clustering techniques may be an interesting approach mainly because of its robustness to evaluate high dimensional data. In this paper, we model the spectral response of insect-herbivory-damage in maize plants and propose an approach based on machine learning and a clustering method to predict whether the plant is herbivore-attacked or not using leaf reflectance measurements. We differentiate insect-type damage based on the spectral response and indicate the most contributive wavelengths to perform it. For this, we used a maize experiment in semi-field conditions. The maize plants were submitted to three different treatments: control (health plants); plants submitted to Spodoptera frugiperda herbivory-damage, and; plants submitted to Dichelops melacanthus herbivory-damage. The leaf spectral response of all plants (controlled and submitted to herbivory) was measured with a FieldSpec 3.0 Spectroradiometer from 350 to 2500 nm for eight consecutive days. We evaluated the performance of different learners like random forest (RF), support vector machine (SVM), extreme gradient boost (XGB), neural networks (MLP), and measured the impact of a day-by-day analysis into the prediction. We proposed a novel framework with a ranking strategy, based on the accuracy returned by predictions, and a clusterization method based on a self-organizing map (SOM) to identify important regions in the reflectance measurement. Our results indicated that the RF-based framework algorithm is the overall best learner to deal with this type of data. After the 5th day of analysis, the accuracy of the algorithm improved substantially. It separated the three treatments into different groups with an F-measure equal to 0.967, 0.917, and 0.881, respectively. We also verified that the most contributive spectral regions are situated in the near-infrared domain. We conclude that the proposed approach with machine learning methods is adequate to monitor herbivory-damage of S. frugiperda and stink bugs like Dichelops melacanthus in maize, differentiating the types of insect-attack early on. We also demonstrate that the framework proposed for the analysis of the most contributive wavelengths is suitable to highlight spectral regions of interest.

Objective. To describe patient satisfaction with pre-hospital emergency knowledge and determine if patients and professionals share a common vision on the satisfaction predictors. Methods. A qualitative study conducted in two phases. First, a systematic review following the PRISMA protocol was carried out searching publications between January 2000 and July 2016 in Medline, Scopus, and Cochrane. Second, three focus groups involving professionals (advisers and healthcare providers) and a total of 79 semi-structured interviews involving patients were conducted to obtain information about what dimensions of care were a priority for patients. Results. Thirty-three relevant studies were identified. A majority conducted in Europe using questionnaires. They pointed out a very high level of satisfaction of callers and patients. Delay with the assistance and the ability for resolution of the case are the elements that overlap in fostering satisfaction. The published studies neither reviewed the overall care process nor related the measurement of the real time in responding to an emergency with the satisfaction. The patients and professionals concurred in their assessments about the most relevant elements for patient satisfaction, although safety was not a predictive factor for patients. Response capacity and perceived capacity for resolving the situation were crucial factors for satisfaction. This qualitative approach yielded assistance targets to be improved. Conclusions. Published studies have assessed similar dimensions of satisfaction. Furthermore, despite the fact that few explanations may be given due to the no face to face attention, taking into account the patient’s emotional needs or maintaining contact with the patient until the emergency services arrive are high predictors of the satisfaction.

Currently, a wide variety of velocity profiles are used in motion control. Thus, this paper compares the energy consumption of three parabolic, trapezoidal, and S-curve profiles. We studied the case of using embedded systems since they are a powerful solution to monitor and coordinate the movement of devices and machinery in various industries combined with motion control applications. These integrated systems allow precise and efficient control of motors and actuators through control and feedback algorithms. In addition, we propose an alternative methodology for implementing motion controllers using an Advanced RISC Machine (ARM) microcontroller, which computes the trajectory and the control action in real-time. We conducted an experiment using a linear plant composed of a direct current (DC) motor coupled to an endless screw where a carriage is mounted that can move mechanically along a rail a distance of 1.16m. In addition, a 4096 pulses per revolution (PPR) encoder is connected to the motor to measure position and angular velocity, which compute the distance the carriage has moved in meters. A current sensor is used to assess the energy consumption, and 40 tests for each profile were carried out to compare the energy consumption for the three-motion profiles considering cases with and without load on the carriage.

The self-assembly is an intriguing process of great importance in general soft matter and thus re-ceives an ever-growing scientific interest. Its most trivial example is the entropy-driven crystalli-zation of hard spheres. Past works have established the similarities and differences in the phase behavior of monomers and chains made of hard spheres. In the present work, inspired by the dif-ference in the melting points of the pure components, we study, through Monte Carlo simulations, the phase behavior of athermal mixtures composed of fully flexible polymers and individual monomers of uniform size. We analyze how the relative number fraction and the packing density affect crystallization and the established ordered morphologies. A synergetic effect is observed in the crystallization leading to synchronous crystallization of the two species. Structural analysis of the resulting ordered morphologies shows perfect mixing and thus no phase separation, which could split the system into polymer-rich and monomer-rich domains. Due to the constraints imposed by chain connectivity, the local environment of the individual spheres is systematically more spherical and more symmetric compared to the one of spheres belonging to chains. In general, increasing polymer content leads to reduction of the degree of crystallinity. According to the present findings, relative concentration is another determining factor to control the phase behavior of hard colloidal systems based on polymers.

Polyalcohol liquefaction can be done by acid or basic catalysis producing polyols with different properties. This study compared the mechanical properties of foams produced using polyols from liquefied Cytisus scoparius obtained by acid and basic catalysis and using two different foam catalysts. The differences were monitored using FTIR analysis. Acid-catalyzed liquefaction yielded 95.1 %, with the resultant polyol having an OH index of 1081 mg KOH/g while basic catalysis yielded 82.5 %, with a similar OH index of 1070 mg KOH/g. Generally, compressive strength with dibutyltin dilaurate (DBTDL) ranged from 16 - 31 kPa (acid-liquefied polyol) and 12 -21 kPa (base-liquefied polyol), while with stannous octoate (TIN), it ranged from 17 - 42 kPa (acid) and 29 - 68 kPa (base). Increasing water content generally decreased the compressive modulus and strength of foams. Higher water content led to a higher absorption at 1670 cm-1 in the FTIR spectrum due to the formation of urea. Higher isocyanate indices generally improved compressive strength, but high amounts led to unreacted isocyanate that could be seen by a higher absorption at 2265 cm-1 and 3290 cm-1. DBTL was shown to be the best foam catalyst due to higher trimer conversion seen in the spectra by a higher absorption at 1410 cm-1. Acid and base-derived polyols lead to different polyurethane foams with different FTIR spectra, particularly with a higher absorption at 1670 cm-1 for foams from acid-derived liquefaction.

Polysaccharides such as alginate and gellan gum are biocompatible and easily accessible biopolymers with excellent properties to produce microparticles as drug delivery systems. However, the production methods often fail in reproducibility, compromising the translational potential of such systems. In this work, microparticles made from gellan gum and alginate were optimized using the coaxial air flow method, and an inexpensive and reproducible production method. A Design of Experiments was used to identify the main parameters that affect the microparticle’s production and optimization, focusing on the diameter and dispersibility. Airflow was the most significant factor for both parameters. Pump flow affected the diameter, whilst the gellan gum/alginate ratio affected dispersibility. After optimization, microparticle swelling, drug entrapment and release profile were analyzed at two pH, 7.4 and 6.5. Using methylene blue as a model drug, higher encapsulation and swelling indexes were obtained at pH 7.4, whilst a more pronounced release occurred at pH 6.5. The microparticle release profiles were studied by resorting to well-known models, showing a Fickian type release. The developed microparticles show promising results as drug-delivery vehicles for biomedical applications.

Almost two decades ago, Ernesto P. Borges and Bruce M. Boghosian embarked on the intricate task of composing a manuscript to honor the profound contributions of Constantino Tsallis to the realm of statistical physics, coupled with a concise exploration of q-Statistics. Fast forward to Constantino Tsallis’ illustrious 80th birthday celebration in 2023, where Deniz Eroglu and Ugur Tirnakli delved into Constantino’s collaborative network, injecting renewed vitality into the project. With hearts brimming with appreciation for Tsallis’ enduring inspiration, Eroglu, Boghosian, Borges and Tirnakli proudly present this meticulously crafted manuscript as a token of their gratitude.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

The aim of this study was to evaluate the intensity of the annual sexual behavior (SB) of Boer bucks under tropical conditions in southern Mexico. For one year, 16 extensively grazing males were evaluated for SB individually with estrogenized goats. From the beginning of the experiment and every 30 days, body weight (BW), body condition (BC), testicular circumference (TC), odor intensity (OI) and SB (nudging, ano-genital sniffing, flehmen, mounting attempts, mounts with intromission, and self-urination) were recorded. The bucks showed a more intense SB during the months of November to May than during the months of June to October (p < 0.05). Greater frequency was found for nudging, ano-genital sniffing, mounting attempts, and self-urination in the months of November to May (p < 0.001). BW was lower during the months of January to August than in the months of September to December (p < 0.05). On the other hand, TC increased from October to December (p < 0.05). Similarly, the OI in males varied over time (time effect; p < 0.001). In fact, an increased odor was found from October to December. The conclusions were that breed male goats from the tropics of Guerrero have a more intense SB during the months of November to May, which corresponds to the time of the year when forage availability is the greatest.

The Eliezer and Gray physical interpretation of the Ermakov-Lewis invariant is applied as a guiding principle for the derivation of the special relativistic analog of the Ermakov-Milne-Pinney equation and associated first integral. The special relativistic extension of the Ray-Reid system and invariant is obtained. General properties of the relativistic Ermakov-Milne-Pinney are analyzed. The conservative case of the relativistic Ermakov-Milne-Pinney equation is described in terms of a pseudo-potential, reducing the problem to an effective Newtonian form. The non-relativistic limit is considered as well. A relativistic nonlinear superposition law for relativistic Ermakov systems is identified. The generalized Ermakov-Milne-Pinney equation has additional nonlinearities, due to the relativistic effects.

The high transmissibility, rapid evolution, and immune escape of SARS-CoV-2 variants can influence the course of infection and, in turn, morbidity and mortality in COVID-19, posing a challenge in controlling transmission rates and contributing to the emergence and spread of new variants. The factors that shape viral genetic variation are consequently essential for understanding the evolution and transmission of SARS-CoV-2, especially in vaccinated individuals where immune response plays a role in the progression and spread of this disease. This study assessed. In this context, we evaluated the impact of immunity induced by the CoronaVac vaccine (Butantan/Sinovac) on intra-host genetic diversity, analyzing 118 whole-genome sequences of SARS-CoV-2 from unvaccinated and vaccinated patients infected with the Gamma variant. Vaccination with CoronaVac favors negative selection at the intra-host level in different genomic regions and prevent greater genetic diversity of SARS-CoV-2, which may help reduce the emergence of new mutations, reinforcing the importance of vaccination in reducing virus transmission.

Manual material handling tasks in industry cause work-related musculoskeletal disorders. Exoskeletons are being introduced to reduce the risk of musculoskeletal injuries. This study investigated the effect of using a passive lumbar exoskeleton in terms of moderate ergonomic risk. Eight participants were monitored by electromyogram (EMG) and motion capture (MoCap) while performing tasks with and without the lumbar exoskeleton. The results showed a significant reduction in the root mean square (VRMS) for all muscles tracked: erector spinae (8%), semitendinosus (14%), gluteus (5%), and quadriceps (10.2%). The classic fatigue parameters showed a significant reduction in the case of the semitendinosus: 1.7% zero-crossing rate, 0.9% mean frequency, and 1.12% median frequency. In addition, the logarithm of the normalized Dimitrov’s index showed reductions of 11.5, 8, and 14% in erector spinae, semitendinosus, and gluteus, respectively. The calculation of range of motion in the relevant joints demonstrated significant differences, but in almost all cases, the differences were smaller than 10. The findings of the study indicate that the passive exoskeleton reduces muscle activity and introduces a minor change of strategies for motion. Thus, EMG and MoCap appear to be appropriate measurements for designing an exoskeleton assessment procedure.

IntroductionGlycogen synthase kinase 3 (GSK-3) has been associated with a lot of diseases, such as Alzheimer’s Disease and diabetes. Its role in depression is connected to stress and neuroinflammation. Lithium is an essential inhibitor of GSK-3. Some studies have suggested that the use of this psychiatric medication may lower suicide rates. Here, we outline the current understanding and discoveries regarding the link between GSK-3 and suicide. MethodWe used the PRISMA statement and defined the PECOS strategy, such as Population (P) = individuals; exposure (E) = GSK-3 alteration function; comparison (C) = without GSK-3 alteration function; outcome (O) = suicide; and study design(S) = all kinds of studies with an association between GSK-3 and suicide.ResultsTwelve studies were included in this review. GSK-3 appears to be related to suicidal behavior by activating inflammatory pathways, activating genes, altering neurotransmission, and increasing impulsivity. Clinical studies do not present robust results that allow defining an epidemiological profile of greater risk for suicidal behavior in association with changes in the functioning of GSK-3.ConclusionThe interference of GSK-3 functioning in suicidal behavior seems inevitable, with solid evidence from laboratory animal studies. However, there is a need for further clinical studies on this crucial topic to answer better some questions about the association between GSK-3 and suicide.

Vasculogenic mimicry (VM), a process in which aggressive cancer cells form tube-like structures, plays a crucial role in providing nutrients and escape routes. Highly plastic tumor cells, such as those with triple-negative breast cancer (TNBC) phenotype, can develop VM. However, little is known about the interplay between cellular components of the tumor microenvironment upon TNBC cells VM-capacity. In this study, we analyzed the ability of endothelial and stromal cells to induce VM when interacting with TNBC cells, and analyzed the involvement of the FGFR/PI3K/Akt pathway in this process. VM was corroborated using fluorescently‐labeled TNBC cells. Only endothelial cells triggered VM formation, suggesting a predominant role of paracrine/ juxtacrine factors from an endothelial origin in VM development. By immunocytochemistry, qPCR and secretome analyses, we determined increased expression of proangiogenic factors as well as stemness markers in VM-forming cancer cells. Similarly, endothelial cells primed by TNBC cells showed upregulation of proangiogenic molecules, including FGF, VEGFA, and several inflammatory cytokines. The endothelium-dependent TNBC-VM formation was prevented by AZD4547 or LY294002, strongly suggesting the involvement of the FGFR/PI3K/Akt axis in this process. Given that VM is associated with poor clinical prognosis, targeting FGFR/PI3K/Akt pharmacologically may hold promise for treating and preventing VM in TNBC tumors.

Oral pyogenic granuloma (PG) is generally a solitary benign connective tissue proliferation of unknown etiology. It is the most common type of oral inflammatory hyperplasia histologically characterized by proliferation of granulation tissue with inflammatory infiltrates and high angiogenic capacity. Vascular neoformations of different diameters are usually present. Due to their structural characteristics, tendency to bleed, and rapid and alarming growth rate, these neoformations may have serious consequences. Sometimes, it is complex to make an accurate diagnosis. Therefore, adequate management and treatment are based on the characteristics and systemic conditions of each patient. This review was carried out to provide an overview of the factors involved in, or attributed to the etiopathogenesis of oral PG. It describes the different forms of presentation and clinical evolution, as well as the most frequent signs and symptoms that characterize this disease, while incorporating recent radiographic and microscopic findings. In addition, it describes the different modalities for the management of oral pyogenic granuloma depending on the particular characteristics of each patient.

Piperine, an active plant alkaloid from black pepper (Piper nigrum), has several pharmacological effects: antioxidant, anti-inflammatory and immunomodulatory, which involves inhibiting molec-ular events associated with various stages of cancer development. The aim of this study was to investigate the molecular mechanisms of action of piperine in relation to its potential anticancer effect on head and neck cancer cells. Parameters related to neoplastic potential, analysis of cyto-kine, protein and gene expression were investigated in the head and neck cancer cell lines (HEp-2 and SCC-25) treated with piperine. The results of the tests indicated that piperine modified mor-phology, inhibited viability and the formation of cell colonies. Piperine promoted genotoxicity by triggering apoptosis and cell cycle arrest in G2/M and S. A decrease in cell migration was also observed, and decreased expression of MMP2/9 genes. Piperine also reduced the expression of inflammatory molecules (PTGS2 and PTGER4), regulated the secretion of cytokines (IF-y and IL-8) and modulated the expression of ERK and p38. These results suggest that piperine exerts anti-cancer effects on tumor cells, and could be a promising natural treatment by regulating signaling pathways associated with head and neck cancer.

Background: The study demonstrates the sustainable synthesis of translucent zinc oxide (ZnO) nanowires using Moringa seed extract, highlighting eco-friendly and sustainable approaches. Methods: Characterization techniques such as X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) confirmed the formation of ZnO nanostructures with diverse morphologies, including nanowires and spherical clusters. Results: The synthesized ZnO nanowires exhibited remarkable photocatalytic activity, achieving over 89% degradation efficiency of methylene blue (MB) under UV light within 80 minutes, demonstrating their potential for wastewater treatment applications. Conclusions: The research findings support Sustainable Development Goals (SDGs) related to clean water, climate action, and life below water and on land, highlighting the role of eco-friendly nanostructures in environmental remediation. The dual advantage of Moringa seed extract, providing both a sustainable synthesis route and health benefits due to its rich content of vitamins and phytochemicals, underscores the potential of integrating natural resources in nanotechnology for environmental and health applications.

In recent years, the potential of insects has been explored as a sustainable protein alternative to sustain the growing world population. Differences in the way insects are processed can affect their proximate composition and digestibility. This work studies the effects of the combination of different types of slaughter methods and drying temperatures on the proximate composition, organic matter digestibility (OMd), hydrolysis degree (DH/NH2 and DH/100 g DM), total hydrolysis (TH) and hygienic sanitary study of BSFL (black soldier fly larvae). Four types of slaughter methods were used: frozen (F), blanched + frozen (B), Melacide® + frozen (M) and liquid nitrogen (N), each with three drying temperatures (50, 70 and 90 °C). A negative correlation between acid detergent fibre (ADF) and protein digestibility parameters was obtained. 70 °C was the most suitable drying temperature, as it reported higher values of protein digestibility (DH, TH), resulting in hygienic and sanitary conditions suitable for food use. Slaughtering with liquid nitrogen and blanching were more convenient than traditional freezing or the use of Melacide® to achieve higher protein digestibility results.

Forest road pavement needs an evaluation methodology based on a comprehensive assessment of road conditions. This research was conducted to evaluate the performance of a method for rating the surface condition of forest roads and eventually to adapt the method to the situation prevailing in a forest road network. The rating method selected as the basis for this experiment was the pavement condition index (PCI) developed by the U.S. Army Corps of Engineers. A 53 km of forest roads were selected contained the most influential factors and conditions variability. Eventually, 201 road segments were delineated between 150-300 m in length. Within the given segments, sample plots were set 20 m in length consecutively. It was concluded that the panel scores for distress and surface condition of sample unit and section differed from forest road pavement condition index (FRPCI) and PCI. Linear regression was used to derive equations between distress and PCI score to determine effective FRPCI parameters that provide a numerical rating for the condition of road segments within the road network, where 0 worlds are the worst possible condition, and 100 is the best possible condition best. Also, regression analysis showed the FRPCI model with a 0.87 correlation for the total of the road is a performance index used for the first time in forest roads. This study showed a range of FRPCI from 7.8 to 96.3, different from PCI and URCI ratings (0.85-45 and 1.2-53). The FRPCI index helps forest managers in road maintenance, harvesting, and planning to use road information.

A E. Crassipes is considered a problem in different aquatic ecosystems, due to its abundance could become a solution to design and build economic and efficient treatment plants, and especially for the production of biofuels such as bioethanol. The objective of this research is to design and implement a sustainable development process between phytoremediation and bioethanol production with E. crassipes, evaluating the incidence of chromium adhered to the biomass of this plant in the production of bioethanol. Materials and methods: A system was installed to evaluate the phytoremediation with E crassipes with water loaded with chromium, determining the effectiveness of this plant to remove this heavy metal even if it is alive in a body of water. After this process, we proceeded to bring the biomass loaded with chromium to bioreactors to evaluate the production of bioethanol, assessing three types of biomass, one without chromium adhered and the other two with chromium adhered to its plant structure. There was an impact of the ethanol production of the E crassipes due to the presence of chromium, but this production can be taken into account for the assembly of an integral system of phytoremediation and bioethanol production, making the most of this biomass.

This study describes the implementation of IoT sensors in drinking water systems and fog collector systems in low-income communities in Ecuador. The influence and handling of these sensors are analyzed, as well as the materials and methods used in their implementation. The importance of validating the accuracy and reliability of IoT sensors compared to professional devices, especially in mountain areas, is highlighted. In addition, it is mentioned that the cost-benefit of using IoT sensors in fog catchers and drinking water networks depends on several factors, such as the scale of the project, specific objectives, and available resources. Finally, it is highlighted that the use of IoT sensors in smart construction and water collection systems has proven to be beneficial in preventing effects on the operation.

This study aimed to evaluate the physico-chemical properties, biocompatibility and bioabsorption of 3 different new membranes for bone guided regeneration (PLGA associated with hydroxyapatite and beta-TCP) with three thicknesses (200, 500 and 700 µm) implanted in mice subcutaneously. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and the quantification of Carbon, Hidrogen and Nitrogen were used to characterize the physico-chemical properties. One hundred Balb-C mice were divided into 5 experimental groups: Group 1 - Sham (without implantation); Group 2 - 200 μm; Group 3 - 500 μm; Group 4 - 700 μm; and Group 5 - Pratix®. Each group was subdivided into four experimental periods (7, 30, 60 and 90 days). Samples were collected and processed for histological and histomorphometrical evaluation. The membranes showed no moderate or severe tissue reactions in the experimental periods studied. The 500 μm membrane did not show tissue reaction for any experimental periods studied. The 200 μm membrane membranes began to exhibit fragmentation after 30- day, while the 500 and 700 µm membranes started the fragmentation at 90-day. All membranes studied were biocompatible, and the 500µm membrane showed the best results being a promissory membrane for bone guided regeneration.

When there is uncertainty in the value of parameters of the input random components of a stochastic simulation model, two-level nested simulation algorithms are used to estimate the expectation of performance variables of interest. In the outer level of the algorithm (n) observations are generated for the parameters, and in the inner level (m) observations of the simulation model are generated with the value of parameters fixed at the value generated in the outer level. In this article, we consider the case in which the observations at both levels of the algorithm are independent, showing how the variance of the observations can be decomposed into the sum of a parametric variance and a stochastic variance. Next, we derive central limit theorems that allow us to compute asymptotic confidence intervals to assess the accuracy of the simulation-based estimators for the point forecast and the variance components. Under this framework, we derive analytical expressions for the point forecast and the variance components of a Bayesian model to forecast sporadic demand; and we use these expressions to illustrate the validity of our theoretical results by performing simulation experiments using this forecast model.

The coffee industry loses millions of dollars annually worldwide due to the Coffee Berry Borer (CBB); these losses imply a decrease in quality and production. Traps are used to monitor their flight and for pest control. The main objective was to determine the flight pattern and trap capture percentages of the CBB population over time using column traps (CTs) in two independent field experiments. CTs were composed of four traps installed at four different heights 0.5, 1.5, 2.5, and 3.5m above ground. Our results demonstrated a significant difference in CBB capture by traps placed at different heights above the ground. The CT capture maintained a pattern throughout this study's lag; the lower the height, the greater the percentage of CBBs captured. In Experiments A and B, the traps placed at 0.5m caught 67% and 85% of the CBBs captured, respectively. Furthermore, the trap set at 1.5m above the ground in the multi-level CT showed a higher capture percentage than the individually placed trap (also at 1.5m). The pattern of the capture and proportion of the CBB in the CTs were maintained throughout the study despite the season, changes in temperature, and relative air humidity. We suggested that CTs could be explored as a useful tool for capturing the CBB, considering its monitoring and management.

Objectives Bone fractures are very common diseases, which can be caused by impact injuries or physiological disorders. Thus, the present review aimed to study the use of medicinal plants in the healing mechanism of bone fractures. Evidence acquisition Through research in the PubMed, Google Academic, and Scielo databases, this article reviews 11 ethnopharmacological studies and 34 preclinical studies on the biological actions of different plants in bone fracture healing mechanism. Results Indian tribes have highlighted in the plants ethnopharmacological study for various diseases, including bone fractures. However, despite the large citations of traditional use, technical-scientific studies are still scarce in the literature. Chenopodium ambrosioides, Piper sarmentosum, quadrangular Cissus, Ricinus communis and Radix salvia miltiorrhiza plants were the most studied in the literature regarding their osteogenic, angiogenic, anti-inflammatory and remodeling effects, acting on bone receptors, stimulating bone metabolism, increasing minerals uptake, and assisting in free radicals breakdown. Conclusion Thus, the medicinal plants use is promising in the field of bone regeneration, as well as being alternative when conventional therapies are unfeasible, increasing herbal medicines demand and popularity.

There is an urgent need to develop new therapies for cancer treatment due to high rates of resistance and tumor relapse. Moreover, chemotherapy and radiation weaken the immune system and leave patients susceptible to sudden death from infections and organ failure since antineoplastic drugs lack specificity. Hence, scientists worldwide continue the search for natural alternatives with anticancer activities and fewer side effects. In this regard, traditional medicine offers strategies for preventing and treating numerous diseases and nowadays scientific studies worldwide highlight some of the mechanisms underlying their potential as an effective alternative for the management of cancer. In Mexico, Mayan healers have been prescribed mainly medicinal plants for more than 2,000 years. Furthermore, their ethnomedical knowledge has led to drug discovery or the development of herbal remedies. Medicinal plants from the genus of Cissus remain an important element of all indigenous medical systems in Mexico including the Mayan tribes in Yucatan, particularly for the management of gastrointestinal illnesses, sores, cutaneous diseases, and tumors. In this review, we present the reported bioactivities against cancer cells of the extract and compounds from the species of Cissus with a particular focus on recent studies on the phytochemistry of C. trifoliata which is widely distributed in Mexican territory and used for tumor management in traditional medicine.

This article analyzes laws, normative reforms and regulations surrounding the practices and mechanisms of control over the consumption, cultivation and commercialization of cannabis. On the one hand, I investigate regulatory practices that deny rights for the consumption of cannabis classified as recreational. On the other hand, I study regulatory practices that extend rights for the production, consumption and commercialization of cannabis classified as medicinal and industrial. The empirical moment is composed of four stages and methodological tools. First, I conduct an analysis of state policies. Then, I analyze nine laws and codes on cannabis regulation from 1970 to the present. Next, I perform five semi-structured interviews. Finally, I develop two life stories of former people deprived of their liberty for cannabis cultivation and trade. In this way, I trace forms of regulation on multiple demands, knowledge, interests and beliefs. This research focuses on state regulation. Cannabis regulatory regimes are conceived as constructions of political, social and economic truths, meanings and rights. In sum, the answer to the question of how collective demands around cannabis are regulated in Ecuador stipulates that state action reinforces stigmatization and criminalization. In addition, it legitimizes moral entrepreneurs and counter-movements around cannabis.

The study of photonic crystals has emerged as an attractive area of research in nanoscience in the last years. In this work we study the properties of a two-dimensional photonic crystal composed of dielectric rods. The unit cell of the system is composed of six rods organized on the sites of a C6 triangular lattice. We induce a topological phase by introducing an angular perturbation ϕ in the pristine system. The topology of the system is then determined by using the so-called k.p perturbed model. Our results show that the system presents a topological and a trivial phases, depending on the sign of the angular perturbation ϕ. The topological character of the system is probed by evaluating the electromagnetic energy density and analyzing its distribution in the real space, in particular on the maximal Wyckoff points. We also find two edge modes at the interface between the trivial and topological photonic crystals, which present a pseudospin topological behavior. By applying the Bulk-Edge correspondence, we study the pseudospin edge modes and conclude that they are robust against defects, disorder and reflection. Moreover, the localization of the edge modes leads to the confinement of light and the interface behaves as a waveguide for the propagation of electromagnetic waves. Finally, we show that the two edge modes present energy flux propagating in opposite directions, which is the photonic analogue of the quantum spin Hall effect.

The dysregulated release of cytokines has been identified as one of the key factors behind poorer outcomes in COVID-19. This ‘cytokine storm ‘produces an excessive inflammatory and immune response, especially in the lungs, leading to acute respiratory distress (ARDS), pulmonary edema and multi-organ failure. Alleviating this inflammatory state is crucial to improve prognosis. Pro-inflammatory factors play a central role in COVID-19 severity, especially in patients with comorbidities In these situations, an overactive, untreated immune response can be deadly, suggesting that mortality in COVID-19 cases is likely due to this virally driven hyperinflammation. Administering immunomodulators has not yielded conclusive improvements in other pathologies characterized by dysregulated inflammation such as sepsis, SARS-CoV-1 and MERS. The success of these drugs at reducing COVID-19-driven inflammation is still anecdotal and comes with serious risks. It is also imperative to screen the elderly for risk factors that predispose them to severe COVID-19. Immunosenescence and comorbidities should be taken into consideration. In this review, we summarize the latest data available about the role of the cytokine storm in COVID-19 disease severity as well as potential therapeutic approaches to ameliorate it. We also examine the role of inflammation in other diseases often comorbid with COVID-19, such as aging, sepsis, and pulmonary disorders. Finally, we identify gaps in our knowledge and suggest priorities for future research aimed at stratifying patients according to risk as well as personalizing therapies in the context of COVID19-driven hyperinflammation.

Wikipedia, as "social machine", is a privileged place to observe the collective construction of concepts without central control. Based on Dahlberg's theory of concept, and anchored in the pragmatism of Hjørland - in which the concepts are socially negotiated meanings - the evolution of the concept of Semantic Web (SW) was analyzed in the English version of Wikipedia. An exploratory, descriptive and qualitative study was designed and we identified 26 different definitions (between 7-12-2001 and 12/31/2017) of which 8 are of particular relevance for their duration, with the latter being the two recorded at the end of the analyzed period. According to them, SW: "is a extension of the web"and "is a Web of Data"; the latter, used as a complementary definition, links to Berners-Lee's publications. In Wikipedia, the evolution of the SW concept appears to be based on the search for the use of non-technical vocabulary and the control of authority carried out by the debate. As a space for collective bargaining of meanings, the Wikipedia study may bring relevant contributions to a community's understanding of a particular concept and how it evolves over time.

We studied the capacity of glutathione and a specific inactivated dry yeast rich in glutathione to protect white grape must from browning compared to using sulphur dioxide. The results indicate that sulphur dioxide drastically reduces the oxygen consumption rate, protects hydroxycinnamic acids from oxidation and prevents grape must against browning even in the presence of laccase. Glutathione, pure or in the form of a specific inactivated dry yeast rich in glutathione, also reduces the oxygen consumption rate but to a lesser extent than sulphur dioxide. It favours the formation of GRP from hydroxycinnamic acids and effectively protects grape must against browning in healthy grape conditions. Nevertheless, in the presence of laccase it was not effective enough. Therefore, both forms of glutathione can be considered as interesting alternative tools to sulphur dioxide for preventing browning in white grape must, but only when the grapes are healthy.

Given the importance of the development of urban infrastructure and environmental impacts produced by the civil construction waste (CCW), it is important to correct the handling of CCW with objective solutions that are more environmentally friendly. In that sense the present study aimed to determine indicators that make it possible to estimate the amount of CCW generated from construction sites in the city of Londrina, Parana State, Brazil. The generation of CCW was estimated in a general way, regarding the composition of its mixture, correlated to the gross areas of the buildings studied and their generated volumes of RCC. This generating rate was evaluated in a general way and specifies two types of sites: the new residential and new non-residential constructions. The data required for the development of these indicators was obtained through extensive survey and interviews carried out at the environment secretariat of the City Hall. The generating rate of CCW obtained for non-residential buildings was 0.2052m3/m2 or 170.44kg/m2, for new residential sites was 0.2054m3/m2 or 170.60kg/m2 and for new commercial or non-residential construction sites, it was 0.20453 m3/m2 or 169.85kg/m2. It was also possible to estimate the amount generated annually per inhabitant in the municipality, which is 0.60m3/inhabit.year or 498.55kg/inhabit.year.

Clinical training in medical schools in Spain is performed by rotations in university hospitals. During these internships, students are expected to acquire and master basic procedural skills. However, the assessment tools available rarely check whether these skills are completely acquired by the students. We have used an e-portfolio to determine the optimal number of times the students need to repeat a procedure to be able to perform it independently. The results were compared with the actual performance during the internships. An e-portfolio collected qualitative information about the internships. Quantitative information was also requested about the number of times each clinical skill was performed. Later, a survey asked these students and their teachers the optimal number of times each skill should be repeated before it could be considered fully acquired. The questionnaire was answered by 98.6% of the students and 70.3% of their teachers. Out of the 21 clinical skills and procedures selected, both students and their tutors agreed in a similar optimal value in 16 of them; only in five of them, teachers thought that students needed a greater number of times than that selected by the students. When these optimal values were compared with the actual values recorded in the portfolio during the internships, it was found that about half of the clinical skills were carried out less frequently than expected, thus providing an important feedback about the internships. Quantitative information collected in portfolios reveals a moderate mismatch between students and tutors perceptions of their training needs.

Abstract: Rotavirus (RV) it’s the agent of one of the main causes of severe viral gastroenteritis in the pediatric population, being responsible for a significant portion of deaths related to diarrhea among children under five years. RV are identified as a potential reference pathogen and it is known that the persistence and infectivity of the viral particles can be related to environmental factors. The aim of the study was to identify and correlate the presence of Rotavirus in collective and individual water sources (deep tubular wells, shallow tubular wells, shallow dug wells, springs, surface water, rainwater stored in cisterns and water trucks that were collected from surface water) of rural communities in the state of Goiás, with the seasons in which the collections were made (rainy and dry season). For this, 86 water samples in the dry period and 160 samples in the rainy period were collected. Concentration of water samples, extraction of viral genetic material, cDNA synthesis and molecular tests (qPCR) were performed. When analyzing the presence of RV in the samples in relation to the period studied, RV was found to be more prevalent in the dry season (54.7%) than in the rainy season (20%), showing a strong statistical association with the dry season (p-value < 0.001). The proportion of positive samples in the dry period, considering the type of source, resulted in higher in Shallow dug wells (p-value <0.001), higher in surface waters (p = 0.001) and higher in spring water (p-value = 0.02). The presence of pathogenic microorganisms in water is a public risk problem, enabling the emergence of outbreaks, endemics and epidemics. In the present research, there was an association among the presence of Rotavirus and the dry period of the year, when compared to the rainy period. Describing or identifying the seasonal behavior of pathogens is important for prevention and attention to water treatment and help in the monitoring of the virus in the water sources.

The Cobb angle is critical in assessing adolescent idiopathic scoliosis (AIS) patients. This study aimed to evaluate the error in selecting the cranial and caudal limit vertebrae on AIS digital X-rays of experienced and novice observers and its correlation with the error in measuring the Cobb angle and determining the length of the scoliotic curves. Using the TraumaMeter v.873 software, eight raters (four experienced and four novices) independently evaluated 68 scoliotic curves on 42 AIS X-rays across three sessions one month apart according to Hopkins’ criteria of absolute reliability. Two spine specialist experts using the Cobb method established the gold standard measurements. The percentage of error in the selection of the cranial vertebrae (the most-tilted vertebra above the apex) is higher than in the caudal vertebrae (the most-tilted vertebrae below the apex) (44.7%, CI95% 41.05-48.3 compared to 35%, CI95% 29.7-40.4). The error in the choice of the most tilted vertebrae, in number of vertebrae per scoliotic curve, was MBE (mean bias error) =0.45, CI95% 0.38-0.52 in the cranial and MBE=0.35, CI% 0.69-0.91 in the caudal. The percentage of errors in the choice of boundary vertebrae is lower for the experienced than for the novices, both in cranial and caudal. The experienced chose at least one boundary vertebrae incorrectly in 52% of the meas-urements and the novices in 65.1%. The error in the Cobb angle did not depend on the number of boundary vertebrae chosen incorrectly (r=0.198, p=0.111). Of the 50% of Cobb angle measurements closest to the actual value, 55.4% (454) were obtained by incorrectly selecting at least one boundary vertebra. There was a positive correlation (r=0.673, p=0.000) between the error in selecting the boundary vertebrae and the error in determining the length of the scoliotic curves. The error in quantifying the length of scoliotic curves was MBE=0.43, CI95% 0.35-0.51 vertebrae per curve. We can conclude that errors in selecting boundary vertebrae are common among experienced and novice observers, with a greater frequency of error in the cranial vertebrae. There is no correlation between the error in selecting the boundary vertebrae and the error in measuring the Cobb angle. Contrary to the consensus, the accuracy of determining the length of the scoliotic curve is limited by the Cobb method’s reliance on the correct selection of boundary vertebrae. Inappropriate choice of boundary vertebrae leads to an estimated error in determining the length of the scoliotic curves of 0.805 vertebrae for each boundary vertebra chosen incorrectly.

Mandarins occupy the third group among citrus produced in Brazil. Primarily aimed at the fresh fruit market, commercial orchards have suffered significant losses in production, due to the high incidence of diseases, such as alternaria brown spot (ABS) and huanglongbing (HLB). The fact that 80% of the orchards are composed of two varieties, Ponkan mandarin and Murcott tangor, are highly susceptible to both diseases, demand intensive chemical control of the diseases in the field, which has resulted in a significant increase in production costs and a negative environmental impact. A total of one hundred and seventy-three mandarin accessions, including several species and hybrids, belonging to the Collections of the Instituto Agronômico de Campinas (IAC), were evaluated in the field, in an endemic location for the diseases. Evaluations of the incidence and severity of the diseases showed that there is a range of genotypes tolerant to ABS with potential to replace the current commercial varieties, mainly within the clementina and Willow leaf mandarin groups. Although with differences in incidence and susceptibility to HLB, there are no varieties tolerant to this disease, which significantly impacts the loss of fruit quality.

The combined influence of the North Atlantic Oscillation (NAO) and the East Atlantic (EA) patterns on the covariability of temperatures and precipitation in 35 stations of the Iberian Peninsula during the period 1950-2019 is analysed in this work. Four EA-NAO composites were defined from teleconnection patterns positive and negative phases: EA+NAO+, EA+NAO-, EA-NAO+, and EA-NAO-. Daily data of maximum and minimum temperature were used to obtain seasonal means (TX, and TN, respectively), and the covariability of these variables with accumulated seasonal rainfall (R) was studied comparing results obtained for different NAO and EA composites. Main results indicate slight differences in the spatial coverage of correlation coefficients between R and temperature variables, except in spring when the generalized negative relationship between R and TX under EA+NAO+ and EA-NAO- disappears under EA-NAO+ and EA+NAO- composites. This result may be useful to interpret and discuss historical reconstructions of Iberian climate.

Several review articles about megachurch studies have been published recently concentrating their work on USA, Europe, and other parts of the world, with just a few references about Latin American megachurches. For that reason, this article aims to identify some of the characteristics of Latin American Evangelical megachurches by looking at relevant literature, especially that produced in the region, in Spanish and Portuguese, which is usually overlooked by researchers in Global North. Since this research field is still limited in Latin America, areas, where further work is necessary, are identified. Three general catalysts for the emergence of megachurches in the region, church growth methodologies, Pentecostalization, and theologies of growth, serve as guides to organize the review process. The discussion shows several potential areas of research in a variety of fields such as theology, ecclesiology, organizational theory, leadership, gender studies, and ethics, are proposed from the review.

The aim of the present work was to evaluate the effects of Thalassia testudinum hydroethanolic extract, its polyphenolic fraction, and thalassiolin B on the activity of phase I metabolizing enzymes as well as their antimutagenic effects. Spectrofluorometric techniques were used to evaluate the effect of tested products on rat and human CYP1A and CYP2B activity. The antimutagenic effect of tested products was evaluated in benzo[a]pyrene (BP)-induced mutagenicity assay by Ames test. Finally, the antimutagenic effect of Thalassia testudinum (100 mg/kg) was assessed in a BP-induced mutagenesis in mice. The tested products significantly (p<0.05) inhibit rat CYP1A1 activity, acting as mixed-type inhibitors of rat CYP1A1 (Ki = 54.16±9.09 μg/mL, 5.96±1.55 μg/mL and 3.05±0.89 μg/mL, respectively). Inhibition of human CYP1A1 was also observed (Ki = 197.1±63.40 μg/mL and 203.10±17.29 μg/mL for the polyphenolic fraction and for thalassiolin B, respectively). In addition, the evaluated products significantly inhibit (p<0.05) benzo[a]pyrene (BP)-induced mutagenicity in vitro. Furthermore, oral doses of Thalassia testudinum (100 mg/kg) significantly reduced (p<0.05) the BP-induced micronuclei and oxidative damage, together with an increase of glutathione, in mice. In summary, Thalassia testudinum metabolites exhibit antigenotoxic activity mediated, at least, by the inhibition of CYP1A1-mediated BP biotransformation. Thus, the metabolites of T. testudinum may represent a potential source of chemopreventive compounds for adjuvant therapy of cancer.

Dioscorea composita is a plant native to México and Central America with a high concentration of diosgenin precursors. Currently, México is one of the two most important countries producers of this yam; however, climate change is altering the environmental conditions of its natural habits, threatening its preservation and productivity. This is why this research was focused to characterize the eco-geography of D. composita and predict its potential geographic distribution under climate change scenarios in México-Central America. A collection of 408 geo-referenced accessions was used to determine its climatic adaptation, ecological descriptors, and the current and future potential geographic distribution, which was modeled with MaxEnt model through the Kuenm R-package. For future climate scenarios, an ensemble of the GCMs HadGEM-ES and CCSM4 was used. Results showed that D. composita adapts to warm humid and very humid agro-climates and that the most contributing variables for its presence are annual and seasonal moisture availability indices, seasonal photoperiod, annual thermal range, Bio14 and Bio11. The year 2050 RCP 4.5 climate scenario would contract the potential distribution of D. composita, whilst the 2050 RCP 8.5 scenario would expand it, indicating that this species could be a good crop option under this scenario of emissions.

Climate change and exposure to environmental pollutants play a key role in the onset and aggravation of allergic diseases. As different climate-dependent patterns of molecular immunoglobulin E (IgE) reactivity have been regionally described, we sought to investigate the evolving allergen exposome in distinctive allergic phenotypes, and subtropical weather conditions through a Precision Allergy Molecular Diagnosis (PAMD@) model. Concurrent sensitization to several house dust mites (HDM) and storage mite molecules were broadly dominant in the investigated cohort, followed by the major cat allergen Fel d 1, and regardless of the basal allergic disease. Although a complex repertoire of allergens was recognized, a steadily increasing number of IgE binding molecules was associated with the complexity of the underlying atopic disease. Besides the highly prevalent IgE responses to HMD major allergens, Der p 21, Der p 5, and Der p 7 also showed as serodominant molecules, especially in those subjects bothered with asthma and atopic dermatitis. The accurate characterization of the external exposome at the molecular level and their putative role as clinically relevant allergens is essential to elucidate the phenotypic diversity of atopic disease in terms of personalized diagnosis and therapy.

Alternaria brown spot (ABS) is a disease caused by the fungus Alternaria alternata f. sp. citri, which results in lesions on fruits, leaves, and branches of several mandarin varieties and their hybrids. Due to the high cost of fungicide application, alternative methods for controlling ABS need to be studied. Therefore, this study aimed to evaluate the use of essential oils (EOs) from different mandarin varieties to mitigate the effects of ABS. The inhibitory effect of different concentrations (1, 2, 4, 8, and 16 μL mL-1) of Fremont IAC 543 mandarin, IAC 2019Maria mandarin, Murcott IAC 221 tangor, and Late IAC 855 willowleaf. EOs on the in vitro mycelial growth of the fungus A. alternata was evaluated. Additionally, the curative and preventive effects of these EOs on ABS symptoms on detached leaves of Murcott IAC 221 tangor were also assessed. The EO of IAC 2019Maria mandarin induced less mycelial growth, and consequently, greater inhibition of the growth of the fungus A. alternata at a concentration of 16 μL mL-1. This EO was more effective in control than the other oils tested. In the detached leaf experiment, both the curative and preventive treatments at a concentration of 16 μL mL-1 showed lower values of disease severity.

Non-enzymatic thiol addition into α,ß-unsaturated carbonyl system is associated with several biological effects. In vivo, the reactions can form small-molecule thiol (e.g., glutathione) or protein thiol adducts. The reaction of two synthetic (4’-methyl- and 4’-methoxy substituted) cyclic chalcone analogs with glutathione and N-acetylcysteine was studied by HPLC-UV method. The selected compounds displayed in vitro cancer cell cytotoxicity (IC50) of different orders of magnitude. The structure of the formed adducts was confirmed by HPLC-MS. The incubations were performed under three different pH conditions (pH 3.5/3.8, 6.3/6.7, and 8.0/7.4). The chalcones intrinsically reacted with both thiols under all incubation conditions. The initial rates and compositions of the final mixtures depended on the substitution and the pH. The frontier molecular orbitals and the Fukui function were carried out to investigate the effects on open-chain and seven-membered cyclic analogs. Furthermore, machine learning protocols were used to provide more insights into physicochemical properties and to support the different thiol-reactivity. HPLC analysis indicated diastereoselectivity of the reactions. The observed reactivities do not directly relate to the different in vitro cancer cell cytotoxicity of the compounds.

This study adapted and assessed a shortened version of the IAT (Internet Addiction Test) scale completed by young people aged 12 years and older regarding their online behaviors and risk of online addiction. The psychometric qualities of the reduced version - Screening IAT - youth are presented in order to validate its use in the early detection of online addiction. The total sample is composed of 3021 participants being 55.9% female and 44.1% male, with a mean age of x ̅=15 years (σ=3.028), attending junior high school (56.2%), high school (37.8%) and college (5.9%). The procedure included a factorial analysis, in which the total sample was randomly divided into three samples. An exploratory factor analysis was performed with one part of the sample, and a confirmatory factor analysis was performed with the others parts, assessing internal consistency, construct reliability, and discriminant validity. The results indicate that this reduced version of the IAT for young people has good psychometric qualities and can be applied in research and clinical settings. With this version and the parent-teacher version there is a direct contribution to a tripartite assessment of internet addiction risk.

Quantum revival phenomena, wherein the wave function of a quantum system periodically returns to its initial state after evolving in time, are investigated in this study. Focusing on electrons confined within a quantum box with an impurity, both weak and strong coupling regimes are explored, revealing intricate relationships between impurity parameters and temporal dynamics. The investigation considers the influence of impurity position, impurity strength, and external factors such as aluminum concentration, temperature, and hydrostatic pressure on classical periods and revival times. Through analytical derivations and graphical analyses, the study elucidates the sensitivity of quantum revivals to these parameters, providing valuable insights into the fundamental aspects of quantum mechanics. While no specific physical applications are discussed, the findings offer implications for quantum heat engines and other quantum-based technologies, emphasizing the importance of understanding quantum revivals in confined quantum systems.

Single Image Super Resolution (SSIR) is a problem in computer vision where the goal is 1 to create high-resolution images from low-resolution ones. It has important applications in fields 2 such as medical imaging and security surveillance. While traditional methods such as interpolation 3 and reconstruction-based models have been used in the past, deep learning techniques have recently 4 gained attention due to their superior performance and computational efficiency. This article proposes 5 an Autoencoder based Deep Learning Model for SSIR, in particular, a light model that uses fewer 6 parameters without compromising performance. The down-sampling part of the Autoencoder 7 mainly uses 3 by 3 convolution and has no subsampling layers. The up-sampling part uses transpose 8 convolution and residual connections from the down sampling part. The model is trained using a 9 subset of the VILRC ImageNet database. The model is evaluated using quantitative metrics PSNR, 10 SSIM as well as qualitative measures such as perceptual quality. PSNR and SSIM figures as high as 11 76.06 and 0.93 are reported.

The vehicular ad hoc network (VANET) when augmented with internet is called internet of vehicles (IoV). In the IoV, vehicles have on board units (OBUs), use communication technologies and customized software to communicate with infrastructure around them. The vehicles can have permanent connectivity and global network awareness based on cloud computing. IoV technologies are still being assessed to ensure that the network is protected from attacks, supports a dynamic vehicular mobility scenarios and meets the low latency communication requirements between the vehicles and the surrounding infrastructure. To meet these strict Quality of Service (QoS) demands, Unmanned Aerial Vehicles (UAVs) play a vital role in IoV ecosystems. An UAV can serve as a mobile roadside unit (mRSU) to transmit data between vehicles, stationery RSUs and other UAVs. The UAVs have better line of sight (LOS) connections which result in better channel states and lower path loss than fixed RSUs. Although the inclusion of UAVs in vehicular networks has improved the system performance by providing better resource management and routing solutions, the traditional optimization techniques with their limitations are often not applicable. Therefore, in recent years, research community is integrating Artificial Intelligence (AI) and Machine Learning (ML) into UAV based IoV ecosystem to better manage resource allocation, routing and mobility management issues to optimize the overall network performance. In this survey paper we review the existing research done in AI/ML based UAV-IoV networks and communications with focus on resource management and routing from year 2019 to 2023. We have studied different AI techniques, their training attributes and architectures in various research works. The limitations of AI-based approaches in terms of required computational resources, availability of real world data and AI models’ complexity for the UAV-IoV environment are also discussed. Finally, the future directions for UAV-IoV research opportunities that can leverage the full potential of AI are presented.

In this study, the objective is to analyze the economic viability of municipal household solid waste (organic matter + paper) for the production of gas, coke and biofuel through the pyrolysis and distillation process. The waste was collected in the city of Belém do Pará-Brazil and pre-treated at UFPA. The analyzed fraction (organic matter + paper) was subjected to pre-treatment of drying, crushing, sieving and was subsequently subjected to proximate characterization and finally pyrolysis of the organic fraction (organic matter + paper) in a fixed bed reactor. Initially, it was necessary to review the literature and with the yields obtained by pyrolysis of the frac-tion, economic feasibility analyzes were carried out. The economic indicators for evaluating the most viable pyrolysis process were: simple payback, discounted payback, net present value (NPV), internal rate of return (IRR), and profitability index (IL). The analysis of the indicators showed the economic viability considering an analysis horizon of 10 years, of materials based on organic material and paper. The break-even point obtained was 0.96 US$/L and the minimum biofuel sales price (MFSP – “Minimum Fuel Sale Price”) obtained in this work was 1.30 US$/L. The sensitivity analysis demonstrated that material costs (organic matter + paper), bio-oil yield, total project investment and electricity, respectively, are the variables that most affect the mini-mum biofuel sales price (MFSP).

Will human societies accommodate social robots, given the current development rate? Are we under a novelty effect? Can (and should) social robots compete with intelligent agents (e.g., software robots) for the attention of humans? Will the current development of machine learning be the motor of social robotics? What kind of robotics products and culture can we expect that will emerge? These are relevant questions to assess the sustainability of social robots and how they will change business practices and lifestyle. Speculative/exploratory arguments on these topics are possible and have been mostly left out of research papers. This, however, results in an unconventional structure where the novelty comes from the questioning of the role of Social Robotics that has not been duly addressed in the literature. The paper raises questions and (i) presents arguments supporting sustainability grounded on experiments in real-world scenarios, and (ii) identifies challenges according to multiple viewpoints. These are questions for which assertive answers are not found in the literature. Besides the answers to the above questions, the conclusions point to pathways we believe social robotics can evolve, e.g., incorporating maximal knowledge on how humans work.

The health benefits of extra virgin olive oil (EVOO) are related with its chemical composition and the presence of bioactive compounds with antioxidant properties. The aim of this study was evaluate antioxidant compounds (pigments, CoQ10 and phenolic compounds) and antioxidant properties of EVOO from the same region comparing different cultivars (Hojiblanca and Arbequina), harvest year and crop stage. Antioxidant properties of oils were studied before and after a gastrointestinal digestion process, by in vitro assays (DPPH, ABTS and FRAP) and antioxidant markers in Caco-2 cells (reactive oxygen species production). The content of bioactive compounds measured was significantly affected by cultivar and harvest year (except for carotenoids) and by the crop stage (except for coenzyme Q10). Higher amount of coenzyme Q10 was observed in Hojiblanca than in Arbequina EVOO. Total phenol content and antioxidant properties were also different depending on cultivar and harvest year and the in vitro digestion process strongly improved antioxidant marker values. Antioxidant potential in bioaccessible fractions was mainly related with content of coenzyme Q10 and phenolic compounds in EVOO. Chemometric analysis showed that the oils were clearly classified by cultivars, harvest and crop stage, according with chemical composition and antioxidant activity analyzed in the present study

In the last decade, the integration of robots into agricultural tasks has significantly transformed food production from planting to harvest. The precision and efficiency of a robot allow for specialized crop management in cases such as; plant disease identification, optimization of water and fertilizer use, monitoring of environmental and soil conditions, among others. That is, the adoption of robots in agricultural practices through intelligent automation increases crop yields and decreases environmental impact. Intelligent automation faces contemporary challenges such as climate change and population growth, promoting sustainable food security. Therefore, this article presents a review of the state of the art of modular robots and their applications in agriculture. Modular robots have the ability to reconfigure and adapt to different tasks, promoting versatile solutions for the agricultural sector. These solutions are linked to the robot's control systems, which can be centralized, decentralized, and hybrid. Firstly, centralized control allows for unified management and coordination in high-precision tasks. Secondly, the decentralized approach offers flexibility and robustness in changing environments where adaptability is required. Thirdly, hybrids incorporate features of both control types balancing control and autonomy to increase efficiency and effectiveness in practical applications. In some cases, control systems incorporate bio-inspired motion control techniques, where the robot mimics natural movements and behaviors to improve its adaptability in performing a task. For example, the chemosynthesis model, which is a biological process where bacteria convert an inorganic compound into energy, has been adapted for individual robots to explore and navigate their environment. Therefore, this article presents an overview of modular robots, the incorporation of bio-inspired motion control techniques, and their convergence towards the sustainable solution of contemporary problems in the agro-industry.

This paper aims to analyze the effects of Covid-19 on financial markets from the perspective of Complexity. The Covid-19 pandemic has caused turmoil in financial markets and is already one of the most important financial crises in history, causing a fall in several stock markets as well as great volatility. Unlike past crises, which in most cases were caused either by problems of fiscal deficits or in the financial system, this crisis has its origin in an epidemic disease, which occurred in Wuhan, China, and quickly spread across the globe affecting transport networks, commerce and finance, and will affect the public debt of many countries. This is a systemic situation in which there is a need to consider several interconnected systems, financial instability and high financial risk, something that econophysics and some complexity theorists already do. Therefore, this paper intends to show, theoretically, the systemic and complex character of the recent financial crisis caused by Covid-19.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.