The anthropogenic deterioration of aquatic ecosystems affects water resources due to agricultural malpractices, pollution from domestic septic tanks, recreational activities, and poor watershed management, among others. This study examines the management of Las Curias Reservoir (176,974 m2), San Juan, Puerto Rico, post the 2016 arrival of the invasive aquatic fern Salvinia molesta. In December 2019, a community-led initiative introduced the Cyrtobagous salviniae weevil, an effective biological control agent for S. molesta, and commenced a mechanical removal campaign using an aquatic harvester. Limnological sampling (September 2019 to March 2022) and drone flights were employed to measure physicochemical and floating plant cover changes, respectively, in the reservoir. Monitoring of weevils in the reservoir demonstrated a rapid establishment and dispersal, which resulted in visible damage including browning of plants and eventually sinking of entire mats. By January 29, 2021, 71% (125,652 m2) of the reservoir surface was covered by salvinia. In 2022, the reservoir recorded an average dissolved oxygen concentration of 2.38 mg/L -1 (± 0.021, n = 144), the highest in the study period and indicative of ecosystem recovery. After three years of control efforts, dissolved oxygen, pH, and specific conductance returned to levels recorded prior to Salvinia molesta introduction. This ecosystem recovery, a first in Puerto Rico, could be attributed to an early use of mechanical control and a long-term impact of biological control.

Background: Atopic dermatitis is a chronic condition that significantly affects the daily life of those who suffer from it, requiring complex and personalized management with active participation of the patient in the management of their disease. Objective: to describe the design and development process of a mobile application, using the Design Thinking method, for the follow-up of patients with atopic dermatitis. Methods: User-centered design and prototype creation method, differentiating the phases of the empathize, define, idea, prototype, and test. A purposive snowball sampling was used to recruit patients with atopic dermatitis, family members, and health professionals. Three two-hour workshops were held, attended by 25 people. Results: the parameters to be monitored will include objective data (physical, behavioral, treatments, environmental, integration of daily routines) and subjective data (user experience). On the other hand, it will figure out behavior patterns, set up rewards, foster a feeling of community, and use notifications and a chatbot. Conclusion: The active integration of all stakeholders at each stage of the design and development of the digital solution has improved its relevance and acceptance, resulting in a tool that is expected to significantly improve the management of atopic dermatitis.

This paper outlines evidence-based practice in the context of professionalism, and highlights the contribution evidence-based practice can make to the professional practice of higher education course managers. Implications of the changing HE landscape for the status of academics as professionals are reviewed, and evidence-based practice is proposed as a solution for both enhanced course management and to remedy perceived deprofessionalisation. Finally, questions regarding researching professional practice within one’s own institution are addressed.

The fluorine-less noble-gas containing anions OBONgO- and OCNNgO-have been studied by correlated electronic structure calculation and density functional theory. The obtained energetics indicates that for Ng = Kr and Xe, these anions should be kinetically stable at low temperature. The molecular structures and electron density distribution suggests that these anions are stabilized by ion-induced dipole interactions with charges concentrated on the electronegative OBO and OCN groups. The current study shows that in additional to the fluoride ion, polyatomic groups with strong electronic affinities can also form stable noble-gas containing anions of the type X-...NgO.

We present here seven new zircon (U-Th)/He (ZHe) ages and three new zircon fission track ages (ZFT) analyzed from an age-elevation profile (Machu Picchu, Peru). ZFT data present older ages in comparison with the other thermochronological data, whereas the ZHe data interestingly present similar ages than the ones obtained with apatite (U-Th)/He (AHe). It has been proposed that He retention in zircon is linked to the damage dose, with an evolution of the closure-temperature from low values associated to low α-dose (<1016 α/g), subsequently increasing before decreasing again at very high α-dose (>1018 α /g). Studies have been focused on the He diffusion behavior at high α-dose, but little is known at low dose. We propose that the ZHe closure temperature at α-dose ranging from 0.6×1015 to 4×1016 α/g is in the range of ~60-80°C. This value is lower than the one proposed in the current damage model ZRDAAM and demonstrates that the ZHe and AHe methods could have similar closure temperatures at low α-dose (i.e. similar ages). These new data strengthen our previous geological conclusions and even highlight an about twice more important cooling rate than the one deduced from AHe and apatite fission-track data alone registered at Machu Picchu.

An ultra-low anti-reflection optical coating on both surfaces of a plastic cover slip was studied for use in confocal image measurement. The optical reflectance at a wavelength of 632.8 nm was less than 0.1% when the coated sample was placed in a liquid having a refractive index of 1.34 close to the aqueous solution of the biomaterial. The high- and low-index coating films, Substance-2 (PrTiO3) and silicon dioxide (SiO2), were measured by an ellipsometer to determine their optical refraction indices and extinction coefficients. Theoretically, when the two layer thicknesses are designed using the optical admittance diagram of the cover slip to approach the equivalent index of 1.34, a reflectance of 1.6×10-5% in the liquid could be obtained. Experimentally, the reflectance of the sample deposited on the two faces of the cover slip was 4.223±0.145% as measured in the air; and 0.050±0.002% as measured by a He-Ne laser in the liquid.

High-spin states of 192Tl are populated by the heavy ion fusion-evaporation reaction 181Ta(16O, 5n)192Tl at 97 MeV beam energy. A new level scheme with eight new levels is constructed and the level spins are tentatively assigned. The negative-parity yrast band is extended up to 23^{-}\hbar. Subsequently, the systematics of signature splitting and signature inversion are discussed for the negative-parity yrast band of odd-odd Tl isotopes including 192Tl, 194Tl, 196Tl, and 198Tl. With the increase of neutron number signature inversion is found in 196,198Tl at high-spin state in these four Tl isotopes. The reason may be due to the competition between neutron-proton interaction and Coriolis force.

Mitochondrial alternative oxidase 1a (AOX1a) plays an extremely important role in critical node of seed viability. However, the regulatory mechanism is still poorly understood. The study aims to identify regulatory mechanisms by comparing between OsAOX1a-RNAi and wild type (WT) rice seed during artificial aging treatment. Gain weight and P50 significantly decreased in OsAOX1a-RNAi rice seed, indicating that there might be impaired in seed development and storability. Compared to WT seeds in the 100%, 90%, 80%, and 70% germination, respectively, NADH and succinate-dependent O2 consumption, the activity mitochondrial malate dehydro-genase and ATP contents were decreased in OsAOX1a-RNAi seeds in the 100%, 90%, 80%, and 70% germination, respectively, indicating that mitochondrial status in the OsAOX1a-RNAi seeds after imbibition was weaken than the WT. In addition to, the reduced abundance of complex I N and P module subunits might showed that the capacity of mitochondrial electron transfer chain was significantly inhibited in the OsAOX1a-RNAi seed at critical node of seed viability. Above results might indicated that the ATP production was impaired in OsAOX1a-RNAi seeds during ageing. Therefore, we conclude that the activities of mitochondrial metabolism and alternative pathways were severely inhibited in OsAOX1a-RNAi seeds at critical node of viability, which was leading to accelerate the collapse of seed viability. The precise regulatory mechanism of the alternative pathway at the critical node of viability still needs to be further analyzed.

Based on research data from the renovation of old residential areas in Chengdu, China, this study provides empirical evidence regarding the causal relationship between urban renewal and the transformation of residents' pro-environmental behaviors. The research findings demonstrate a significant enhancement in residents' engagement in pro-environmental behaviors due to the renovation of old residential areas. Robustness tests based on replacement samples and two-stage difference-in-difference models also confirm the reliability of the conclusions. The preliminary mechanism test indicates that the mechanism of the impact of renovation of old residential areas on the transformation of residents' pro-environmental behaviors can be attributed to two main factors. Firstly, the improvement of environmental infrastructure provides residents with better conditions for participating in pro-environmental activities. Secondly, there is an elevation in residents' environmental protection awareness, prompting a more voluntary engagement in pro-environmental behavior. This study suggests that decision-makers should fully recognize that urban renewal activities nationwide are not only a process of improving urban hardware and functionality, but also a realistic and vivid "environmental education" course for the whole nation. Taking urban renewal as an opportunity to enhance citizens' awareness of environmental protection will effectively promote the transformation of pro-environmental behaviors among residents.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

The impact of drought stress on plant growth in arid regions is a critical concern, necessitating the exploration of strategies to enhance plant drought resistance, particularly during the early stages of drought stress. This study focuses on the ectomycorrhizal fungus Cenococcum geophilum, renowned for its extensive genetic diversity and broad host compatibility, making it a crucial ally for host plants facing external stresses. We utilized approximately 5-month-old Pinus massoniana seedlings inoculated with different ecotypic strains of C. geophilum for 7 days of drought stress. The results showed that the inoculation of most strains of C. geophilum enhanced the drought resistance of P. massoniana seedlings under the early stages of drought stress, by influencing the water content, photosynthesis, accumulation of osmotic adjustment substances, and antioxidant enzyme activities in both shoots and roots of seedlings. These responses were further validated through transcriptome analysis. Notably, the level of drought resistance observed in mycorrhizal seedlings was irrespective of the level of drought tolerance of C. geophilum strains. This study contributes essential data for understanding the drought response mechanisms of mycorrhizal P. massoniana seedlings inoculated by distinct C. geophilum ecotypes, and guidance on selecting candidate species of ectomycorrhizal fungi for mycorrhizal afforestation in drought areas.

Phenacoccus manihoti (Hemiptera: Pseudococcidae), is an invasive pest that is very detrimental to cassava cultivation in Indonesia. Control efforts by utilizing natural enemies of the parasitoid have succeeded in overcoming the cassava mealybug in 25 countries such as in Africa and Thailand. The purpose of this study was to specifically evaluate the potential for parasitoid species associated with the mealybug P. manihoti by (1) determining the level of parasitization against mealybugs on various varieties of cassava, (2) determining parasitoid preference for P. manihoti instars, and (3) determining the type of parasitoid. This study was undertaken in the field to re-evaluate the kinds of parasitoids associated with cassava pests, and in the laboratory to assess the amount of parasitization, predilection, and functional response of parasitoids to P. manihoti population density. The findings revealed three of parasitoids linked with P. manihoti in the field: Anagyrus lopezi, Acerophagus sp., and Blepyrus sp. The parasitoid A. lopezi had the greatest parasitization rate in the field, which was 18.67 %. Furthermore, the parasitoids A. lopezi and Blepyrus sp. preferred 3rd instar nymphs, but Acerophagus sp. preferred 2nd instar nymphs. The parasitoid A. lopezi demonstrated a type-III functional response, while Acerophagus sp. and Blepyrus sp. demonstrated a type-II functional response. The handling capacity (Th) of A. lopezi is the shortest at 3.42 minutes. This work is a comprehensive study of the parasitoid A. lopezi's potential as a biological agent, highlighting how it effectively suppresses P. manihoti on various cassava varieties in Bali, providing an inexpensive, environmentally friendly, and applicable control in tropical countries.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

: Sputtering of silicon in a Helium magnetron discharge (MS) has been reported as a bottom-up procedure to obtain He-charged silicon films (i.e. He nanobubbles encapsulated in a silicon matrix). The incorporation of heavier noble gases is demonstrated in this work with a synergistic effect producing increased Ne and Ar incorporations when using He-Ne and He-Ar gas mixtures in the MS process. Microstructural and chemical characterizations are reported by ion beam analysis (IBA) and scanning and transmission electron microscopies (SEM and TEM). In addition to gas incorporation, helium promotes the formation of larger nanobubbles. For the case of Ne high resolution X-ray photoelectron and absorption spectroscopies (XPS and XAS) are reported with remarkable dependence of the Ne 1s photoemission and the Ne K-edge absorption on the nanobubbles size and composition. The gas (He, Ne, Ar) charged thin films are proposed as “solid” targets for the characterization of spectroscopic properties of noble gases in a confined state without the need for cryogenics or high-pressure anvils devices. Also their use as targets for nuclear reaction studies is foreseen.

The reason for excessive multidecade deflections is still unclear after 70 years of the cantilever method that has been applied in building large-span segmental concrete bridges. The failure of the Koror-Babeldaob bridge gives the author a clue that the reason might be the boundary condition. The asymmetric properties of the bearing and prestress tendon draw the author’s attention. To understand the process of stress redistribution, the virtual stiffness method which is derived from the principle of minimum potential energy was created, and the phenomenon the author suggested named Material Inelasticity and Prestress Loss Coupling Effect is discovered. The unexplainable excessive deflection and prestress loss are found in the new load model. The calculation of excessive deflection is discussed. The new model fits the experience well. The optimization design methods and construction key points are proposed.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

This work is a natural extension of the author’s previous work: “Multiple scattering theory for heterogeneous elastic continua with strong property fluctuation: theoretical fundamentals and applications” (arXiv:1706.09137 [physics.geo-ph]), which established the foundation for developing multiple scattering model for heterogeneous elastic continua with either weak or strong fluctuations in mass density and elastic stiffness. Polycrystalline material is another type of heterogeneous materials that widely exists in nature and extensively used in industry. In this work, the corresponding multiple scattering theory for polycrystalline materials with randomly oriented anisotropic crystallites is developed. To validate the theory, the theoretical results for a series of materials such as OFHC copper, 304 stainless steel, and Inconel 600 are compared to experimental measurements and the numerical results obtained using finite element simulations. Detailed analysis shows that the new theory is capable of predicting the dispersion and attenuation of polycrystals with satisfactory accuracy. The results also show the new model can give an estimate on the average grain size with a relative error equal to or less than ten percent. As applications in ultrasonic nondestructive evaluation, we calculated the dispersion and attenuation coefficient of one of the most important polycrystalline materials in aeronautics engineering: high-temperature titanium alloys. The effects of grain symmetry, grain size, and alloying elements on the dispersion and attenuation behaviors are examined. Key information is obtained which has significant implications for quantitatively evaluating the average grain size, monitoring the phase transition, and even estimating gradual change in chemical composition of titanium components in gas turbine engines. For applications in seismology, the velocities and Q-factors for both hexagonal and cubic polycrystalline iron models for the Earth’s uppermost inner core are obtained in the whole frequency range. Using the realistic material parameters of iron under the high temperature and high-pressure conditions calculated from ab initio simulations, the numerical results show that the Q-factors range from 0.001 to 0.05, which shows good agreement with that inferred from real seismic data. The new model predicts the velocity of longitudinal waves varies between ± 1% to ± 5 % relative to the Voight average velocity, while the velocity of transverse waves varies from ± 10% to ± 20%, which gives promising explanation to the abnormally slow transverse velocity observed in practical measurements. The numerical results support the conjecture that the Earth’s uppermost inner core is a solid polycrystalline medium. The comprehensive numerical examples show the new model is capable of capturing the most important scattering features of both ultrasonic and seismic waves with satisfactory accuracy. This work provides a universal, quantitative model for characterization of a large variety of polycrystalline materials. It also can be extended to incorporate more complicated microstructures, including ellipsoidal grains with or without textures, and even multi-phase polycrystalline materials. The new model demonstrates great potential of applications in ultrasonic nondestructive evaluation and inspection of aerospace and aeronautic structures. It also provides a theoretical framework for quantitative seismic data explanation and inversion for the material composition and structural formations of the Earth’s inner core.

Scattering of elastic waves in heterogeneous media has become one of the most important problems in the field of wave propagation due to its broad applications in seismology, natural resource exploration, ultrasonic nondestructive evaluation and biomedical ultrasound. Nevertheless, it is one of the most challenging problems because of the complicated medium inhomogeneity and the complexity of the elastodynamic equations. A widely accepted model for the propagation and scattering of elastic waves, which properly incorporates the multiple scattering phenomenon and the statistical information of the inhomogeneities is still missing. In this work, the author developed a multiple scattering model for heterogeneous elastic continua with strong property fluctuation and obtained the exact solution to the dispersion equation under the first-order smoothing approximation. The model establishes an accurate quantitative relation between the microstructural properties and the coherent wave propagation parameters and can be used for characterization or inversion of microstructures. Starting from the elastodynamic differential equations, a system of integral equation for the Green functions of the heterogeneous medium was developed by using Green’s functions of a homogeneous reference medium. After properly eliminating the singularity of the Green tensor and introducing a new set of renormalized field variables, the original integral equation is reformulated into a system of renormalized integral equations. Dyson’s equation and its first-order smoothing approximation, describing the ensemble averaged response of the heterogeneous system, are then derived with the aid of Feynman’s diagram technique. The dispersion equations for the longitudinal and transverse coherent waves are then obtained by applying Fourier transform to the Dyson equation. The exact solution to the dispersion equations are obtained numerically. To validate the new model, the results for weak-property-fluctuation materials are compared to the predictions given by an improved weak-fluctuation multiple scattering theory. It is shown that the new model is capable of giving a more robust and accurate prediction of the dispersion behavior of weak-property-fluctuation materials. Numerical results further show that the new model is still able to provide accurate results for strong-property-fluctuation materials while the weak-fluctuation model is completely failed. As applications of the new model, dispersion and attenuation curves for coherent waves in the Earth’s lithosphere, the porous and two-phase alloys, and human cortical bone are calculated. Detailed analysis shows the model can capture the major dispersion and attenuation characteristics, such as the longitudinal and transverse wave Q-factors and their ratios, existence of two propagation modes, anomalous negative dispersion, nonlinear attenuation-frequency relation, and even the disappearance of coherent waves. Additionally, it helps gain new insights into a series of longstanding problems, such as the dominant mechanism of seismic attenuation and the existence of the Mohorovičić discontinuity. This work provides a general and accurate theoretical framework for quantitative characterization of microstructures in a broad spectrum of heterogeneous materials and it is anticipated to have vital applications in seismology, ultrasonic nondestructive evaluation and biomedical ultrasound.

The geometry of mesoscopic inhomogeneities plays an important role in determining the macroscopic propagation behaviors of elastic waves in a heterogeneous medium. Non-equiaxed inhomogeneities can lead to anisotropic wave velocity and attenuation. Developing an accurate scattering theory to describe the quantitative relation between the microstructure features and wave propagation parameters is of fundamental importance for seismology and ultrasonic nondestructive characterization. This work presents a multiple scattering theory for strongly scattering elastic media with general tri-axial heterogeneities. A closed analytical expression of the shape-dependent singularity of the anisotropic Green’s tensor for the homogeneous reference medium is derived by introducing a proper non-orthogonal ellipsoidal coordinate. Renormalized Dyson’s equation for the coherent wave field is then derived with the help of Feynman’s diagram technique and the first-order-smoothing approximation. The exact dispersion curves and the inverse Q-factors of coherent waves in several representative medium models for the heterogeneous lithosphere are calculated numerically. Numerical results for small-scale heterogeneities with the aspect ratio varying from 1 to 7 show satisfactory agreement with those obtained from real earthquakes. The results for velocity dispersion give rise to a novel explanation to the formation mechanism of different seismic phases. The new model has potential applications in seismology and ultrasonic microstructure characterization.

The hyper-arid environment is characterized by high inter-annual climatic fluctuations. The yearly average rainfall can change substantially for several years, forming wet or dry sub-periods. Observing rainfall trends over a sub-period can lead to a false perception of a change in the trend but may in fact represent a periodic cycle when examined on a larger time scale. We aimed to better characterize the rainfall regime prevailing in the hyper-arid Arava Valley (Israel/Jordan), and to examine the response of vegetation to annual rainfall. We hypothesized that annual and perennial vegetation would respond differently to wet and dry sub-periods, and that grazing activities will impact vegetation growth. We used a time series of monthly rainfall, from which we calculated Standard Precipitation Index (SPI), and calculated proxies of perennial and annual vegetation over the last four decades using Landsat-derived Normalized Difference Vegetation Index (NDVI). We found no clear trend in rainfall amounts during this period, however we did identify wet and dry sub-periods which were statistically distinct in rain and in vegetation patterns from each other. The highest levels of correlation between rainfall and the NDVI derived proxies were found when examining average rainfall over a period of two- three years for the annual vegetation and over four years for perennial vegetation. Using the Mann-Kendall test, we identified a time lag of two to four years, with the proxies of annual vegetation responding faster than the proxies of perennial vegetation, to shifts between wet and dry sub-period. In addition, we found a consistent difference between natural vegetation cover in Jordan (grazed) and Israel (non-grazed), favoring the development of natural vegetation on the Israeli side. We conclude that integrating between long-term remote sensing satellite imagery and climatic records revealed the greater resilience of perennial vegetation in the hyper-arid region to climatic fluctuation, and enabled us to identify the vegetation’s sensitivity to anthropogenic impact.

The paper studies some cases in physics such as Galilean inertia motion and etc., and presents a logical schema of recursive abduction, from which we can derive the universality of physical laws in an effective logical path without requiring infinite inductions. Recursive abduction provides an effective logical framework to connect a universal physical law with finite empirical observations based on both quasi-law tautologies and suitable recursive dimensions, two new concepts introduced in this paper. Under the viewpoint of recursive abduction, the historical difficulty from Hume’s problem naturally vanishes. In Hume’s problem one always misunderstood a time-recursive issue as an infinitely inductive problem and, thus, sank into an inescapable quagmire. With this new effective logical schema, the paper gives a concluding discussion to Hume’s problem and justifies the validity of probability argument for natural laws.

Technology has transformed aeroponics, providing numerous advantages over traditional soil-based agriculture. However, there remains a need for comprehensive information on the types of technology employed in aeroponics and their impact on the growing process. This paper presents a literature review of 47 studies published between 2012 and 2023 in peer-reviewed journals and conference proceedings. As a result, it identifies the status and tendencies in the usage of technology in aeroponics as well as the main opportunities and challenges. Furthermore, this paper introduces the Technology Adoption and Integration in Sustainable Agriculture (TAISA) model. TAISA is a model that identifies the degree of technology integration in any sustainable agriculture system to determine how technology affects production and quality. Overall, the systematic review suggests that technology can play a vital role in improving the efficiency and sustainability of aeroponic farming. However, careful consideration must be given to the costs and technical requirements associated with using these technologies. Moreover, the TAISA model reveals that technology has primarily been employed in creating new processes that are not possible to implement without the help of technology. Therefore, we conclude that technology use has taken root in aeroponics and can be promoted to improve sustainable agriculture.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

This article focuses on generating an alternative in order to identify traffic officers during driving. This research employed the latest You Only Look Once (YOLO) model, using a six-phase methodology: data collection, data preparation involving resizing and labeling, implementation of various filters to avoid overfitting, model training, prediction evaluation, and result interpretation. The YOLO model was applied across three iterations using a dataset of 1862 images. To enhance training efficiency and detection speed, the graphics processing unit (GPU) acceleration was utilized, further enhancing the experimental process. The results of this study revealed that the YOLOv8x variant produced the most promising results. This proposed model attained a remarkable F1 score of 0.95, bolstered by a confidence score of 0.631, with the potential for an increase to 0.80 in confidence without significantly compromising the F1-score. These findings are poised to make a substantial contribution to the broader research landscape, particularly in advancing the effectiveness of detection models for traffic officers.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

Translation is spatiotemporally regulated and ER-associated mRNAs are generally in efficient translation. It is unclear whether the ER-associated mRNAs are deadenylated or degraded on the ER surface in situ or in the cytosol. Here, we showed that ER possessed active deadenylases, particularly the poly(A)-specific ribonuclease (PARN), in common cell lines and mouse tissues. Consistently, purified recombinant PARN exhibited a strong ability to insert into the Langmuir monolayer and liposome. ER-anchored PARN was found to be able to reshape the poly(A) length profile of the ER-associated RNAs by suppressing long poly(A) tails without significantly influencing the cytosolic RNAs. The shortening of long poly(A) tails did not affect global translation efficiency, suggesting that the non-specific action of PARN towards long poly(A) tails was beyond the scope of translation regulation on the ER surface. Transcriptome sequencing analysis indicated that the ER-anchored PARN trigged the degradation of a small subset of ER-enriched transcripts. The ER-anchored PARN modulated the translation of its targets by redistributing ribosomes to heavy polysomes, suggesting that PARN may play a role in dynamic ribosome reallocation. During DNA damage response, MK2 phosphorylated PARN-Ser557 to modulate PARN translocation from the ER to cytosol. By promoting the decay of ER-associated MDM2 transcripts with low ribosome occupancy, the ER-anchored PARN modulated DNA damage response and thereby cell viability. These findings revealed that a highly regulated communication between mRNA degradation rate and translation efficiency is present on the ER surface in situ and that PARN may contribute to this communication by modulating the dynamic ribosome reallocation between transcripts with low and high ribosome occupancies.

Rural landscapes are acknowledged for their potential to restore human health due to their natural characteristics. However, few studies have systematically analysed the impact of naturalness, landscape types, and combinations of landscape elements on restorativeness using both subjective and objective measurements. This study investigated the restorative effects of various rural landscapes in Guangzhou, employing electroencephalography and eye-tracking technologies to record physiological responses and using the Restorative Components Scale and the Perceived Restorativeness and Naturalness Scale to evaluate psychological responses. The results indicated the following: (1) There was a significant positive correlation between perceived naturalness and restorativeness, surpassing the impact of actual naturalness. (2) Different landscape types had a varying impact on mental health at the equal perceived naturalness. Natural forest landscapes and artificial forest landscapes exhibited the most substantial restorative effects among the natural and semi-natural landscapes examined, respectively, while settlement landscapes showed the highest restorative potential among the artificial landscapes. (3) Restorative properties varied across landscape elements, with identical elements yielding different benefits in different environments. Trees and water significantly enhanced restorativeness, whereas constructed elements such as roads and infrastructure reduced it. This study provides a scientific basis for restorative rural landscape design to enhance mental health and well-being.

In order to shorten the detection time and improve the average precision on embedded devices, A lightweight and high accuracy model is proposed for passion fruit in complex environments (backlight, occlusion, overlap, sunny, cloudy, rainy). Firstly, replacing the backbone network of YOLOv5 with a lightweight GhostNet model reduces the number of parameters and computation while improving detection speed. Secondly, a new feature branch is added to the GhostNet network, and the feature fusion layer in the neck network is reconstructed to effectively combine the lower-level and higher-level features, which not only improves the accuracy of the model but also maintains its lightweight. Finally, the knowledge distillation methods are used to transfer the knowledge from the more capable teacher model to the less capable student model, which significantly improving the detection accuracy. The improved model is denoted as G-YOLO-NK. The average accuracy of the G-YOLO-NK network is 96.00%, which is 1.00% higher than the original YOLOv5s model. Furthermore, the improved model size is 7.14MB, reduced to half of the original model, and the real-time detection frame rate is 11.25 FPS on the Jetson Nano. Compared to the state-of-the-art model, the proposed model outperforms them in terms of average precision and detection performance. The present work provides an effective model for real-time detection of passion fruits in complex orchard scenes, which can provide valuable technical support for the development of orchard picking robots and greatly improve the intelligence level of orchards.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

The Shule River Basin (SRB) is a typical arid area in northwest China with a fragile ecology. Un-derstanding vegetation dynamics and its response to climate change and human activities provides essential information for ecological and environmental resource management. This study extracted fractional vegetation coverage (FVC) data from 2000 to 2019 using the Google Earth Engine plat-form and Landsat satellite images, employing trend analysis and other methods to examine spati-otemporal changes in vegetation in the SRB. Additionally, partial correlation and residual analysis were utilized to explore the response of FVC to climate change and human activities. The main results were as follows: (1) The regional average FVC in the SRB showed a significant upward trend from 2000 to 2019, increasing by 1.3 × 10−3 y–1. The area within 1 km of roads experienced a higher increase of 3 × 10−3 y–1, while the roadless areas experienced a lower increase of 1.1 × 10−3 y–1. Road construction from 2004 to 2006 significantly reduced the FVC within 200 meters of the roads. FVC spatial heterogeneity in the SRB is significant. (2) Partial correlation analysis shows that FVC has a strong positive correlation with precipitation and surface water area, with correlation coefficients of 0.575 and 0.744, respectively. There is a weak negative correlation between FVC and land surface temperature (LST). FVC changes are more influenced by precipitation than by LST. (3) Compared to climate factors, human activities have a greater impact on vegetation dynamics in the SRB. The contributions of climate change to vegetation recovery are increasing. (4) The area changes of dif-ferent land types are closely related to climate factors and human activities, reflecting their impact on vegetation. These results provide valuable information for ecosystem restoration and environ-mental protection in the SRB.

Recurrent Pregnancy Loss (RPL) affects 1-2% of women, and its triggering factors are unclear. Several studies have shown the vaginal, endometrial, and gut microbiota may play a role in RPL. A decrease in the quantity of Lactobacillus crispatus in local microbiota has been associated with an increase in local (vaginal and endometrial) inflammatory response and immune cell activation that leads to pregnancy loss. The inflammatory response may be triggered by gram-negative bacteria, lipopolysaccharides (LPS), viral infections, mycosis, or atypia (tumor growth). Bacterial structures and metabolites produced by microbiota could be involved in immune cell modulation and may be responsible for immune cell activation and molecular mimicry. Gut microbiota metabolic products may increase the amount of circulating pro-inflammatory lymphocytes, which, in turn, will migrate into vaginal or endometrial tissues. Local proinflammatory Th1 and Th17 subpopulations along with a decrease in Treg and tolerogenic NK cells are accountable for the increase in pregnancy loss. Local microbiota may modulate the local inflammatory response increasing pregnancy success. Analyzing local and gut microbiota may be necessary to characterize some RPL patients. Although oral supplementation of probiotics has not been shown to modify vaginal or endometrial microbiota, the metabolites produced by it may benefit patients. Lactobacillus crispatus transplantation into the vagina may enhance the required immune tolerogenic response to achieve a normal pregnancy. The effect of hormone stimulation and progesterone to maintain early pregnancy on microbiota has not been adequately studied, and more research is needed in this area. Well-designed clinical trials are needed to ascertain the benefit of microbiota modulation in RPL.

This preprint is focused in the presence of plastics and microplastics in food. We will discuss how many we eat, and how they arrive to the food, and why. We will treat many other things, such as the waste treatment in Europe and in Spain, with updated data; how much plastic waste is generated; what are microplastics and how they are analyzed, I will tell about the experience we have at the University of Alicante (UA); how they can be removed and we will estimate how many we eat over the course of a year.

An essential step in solving any topology optimization problem is determining the sensitivities of the objective function and optimization constraints. Unfortunately, these sensitivities are usually derived and implemented manually. Nontrivial objective functions and constraints, especially with the involvement of material and geometric nonlinearities, need strenuous mathematical derivation, leading to error-prone implementation. Another intriguing approach to finding sensitivities is automatic differentiation. This paper uses the automatic differentiation and adjoint method to find the sensitivities for two multiphysics topology optimization problems: 1) thermoelasticity and 2) piezoelectricity. This approach is not limited to these examples and can be easily extended to other single- or multi-physics topology optimization problems.

A facilitative transport system exists on the blood brain barrier (BBB) that has been tacitly assumed to be a path for glutamate entry to brain. But glutamate is a non-essential amino acid whose brain content is much greater than plasma, and studies in vivo show that glutamate does not enter brain in material quantities except in those small regions with fenestrated capillaries (circumventricular organs). The situation became understandable when luminal (blood facing) and abluminal (brain facing) membranes were isolated and studied separately. Facilitative transport of glutamate and glutamine exist only on the luminal membranes whereas Na+-dependent transport systems for glutamate, glutamine and some other amino acids are present only on the abluminal membrane. The Na+-dependent cotransporters of the abluminal membrane are in a position to actively transport amino acids from the extracellular fluid (ECF) into the endothelial cells of the BBB. These powerful secondary active transporters couple the energy of the Na+-gradient to move glutamate and glutamine into the ECF whereupon glutamate can exit to blood on the luminal facilitative glutamate transporter. Glutamine may also exit brain on a separate facilitative transport system that exists on the luminal membranes or glutamine can be hydrolyzed to glutamate within the BBB thereby releasing ammonia that is freely diffusible. The γ-glutamyl participate cycle participates indirectly by producing oxoproline (pyroglutamate) that stimulates almost all secondary active transporters yet discovered in the abluminal membranes of the BBB.

Soft set theory is a mathematical tool for dealing with uncertainty. This paper investigates limits of interval type of soft sets (for short, it-soft sets). The concept of it-soft sets is first introduced. Then, limits of it-soft sets are proposed and their properties are obtained. Next, point-wise continuity of it-soft sets and continuous it-soft sets are discussed. Finally, an application for rough sets is given.

Pruning is one of the most important tree fruit production activities, which is highly dependent on human labor. Skilled labor is in short supply, and the increasing cost of labor is becoming a big issue for the tree fruit industry. Growers are motivated to seek mechanical or robotic solutions for reducing the amount of hand labor required for pruning. This paper reviews the research and development of sensing and automated systems for branch pruning for tree fruit production. Horticultural advancements, pruning strategies, 3D structure reconstruction of tree branches, as well as practice mechanisms or robotics are some of the developments that need to be addressed for an effective tree branch pruning system. Our study summarizes the potential opportunities for automatic pruning with machine-friendly modern tree architectures, previous studies on sensor development, and efforts to develop and deploy mechanical/robotic systems for automated branch pruning. We also describe two examples of qualified pruning strategies that could potentially simplify the automated pruning decision and pruning end-effector design. Finally, the limitations of current pruning technologies and other challenges for automated branch pruning are described, and possible solutions are discussed.

Over the last ten years, the integrated pond aquaculture (IPA) has been developing rapidly as a new aquaculture mode, and mechanical power oxygenator is a common oxygenation device in this aquaculture mode. However, with the gradual expansion of the application range of this aquaculture mode, the problems of low efficiency, poor oxygenation uniformity, and low applicability of mechanical power oxygenators, which can produce water reflux and suction pollution accumulation, have gradually emerged. Therefore, we designed a new type of push-water aerator device (NPWAD) applicable to the integrated recirculating water aquaculture mode of ponds. Mainly, the specific parameters of the key components were clarified through the selection calculation and structural design, and the experiments were carried out in the self-constructed pond integrated aquaculture system at the experimental base. The experiments were carried out on the water in the tank for grass carp culture, and the oxygenation and water pushing effects of the type of push-water aerator device under 15 groups of different operating parameters were carried out by using multiple types of high-precision water quality monitoring sensors, with the rotational speed of the device, the operating time (0-30 min) and the height of the water (0.5-1.5 m) as the independent variables, and the oxygenation amount R, the oxygenation power efficiency E_s and the surface layer of the water as the evaluation indexes, average flow velocity V_f were used as its evaluation indexes of oxygenation and water pushing. The results show that the optimal parameters of the NPWAD are impeller water lifting component speed n_1=1000r/min, small-hole aeration component speed n_2=2280r/min. At this time, the average oxygen increase of this device is R=1.96mg/L, the average oxygenation power efficiency is E_s=3.8 kg·(h·kW)-1, the DO uniformity of the water M_1=95.3%, and the average flow velocity V_f=190.8mm/s, which can effectively promote the water directional flow and achieve the water circulation and layer exchange, and it is in line with the preferred swimming speed of grass carp at various growth stages. The new type of push-water aerator device is able to enhance the DO concentration of the water faster, but also to achieve the purpose of promoting the directional flow of the water and renewing the water in the tank, as well as in a short period of time to improve the uniformity of the DO of the water faster, for the improvement of the pond aquaculture production efficiency has practical significance.

A construction for the systems of natural and real numbers is presented in Zermelo-Fraenkel Set Thoery, that allows for simple proofs of the properties of these systems, and practical and mathematical applications. A practical application is discussed, in the form of a Simple and Linear Fast Adder (Patent Pending). Applications to finite group theory and analysis are also presented. A method is illustrated for finding the automorphisms of any finite group $G$, which consists of defining a canonical block form for finite groups. Examples are given, to illustrate the procedure for finding all groups of $n$ elements along with their automorphisms. The canonical block form of the symmetry group $\Delta_4$ is provided along with its automorphisms. The construction of natural numbers is naturally generalized to provide a simple and sound construction of the continuum with order and addition properties, and where a real number is an infinite set of natural numbers. A basic outline of analysis is proposed with a fast derivative algorithm. Under this representation, a countable sequence of real numbers is represented by a single real number. Furthermore, an infinite $\infty\times\infty$ real-valued matrix is represented with a single real number. A real function is represented by a set of real numbers, and a countable sequence of real functions is also represented by a set of real numbers. In general, mathematical objects can be represented using the smallest possible data type and these representations are calculable. In the last section, mathematical objects of all types are well assigned to tree structures in a proposed type hierarchy.

While digitization can make the health industry faster and more efficient, there are many financial, social and organizational obstacles and barriers to its implementation. This article offers a systematic review of the main troubles detected from the literature review. Also there is a proposal of new kind of restrictions to pay attention. Finally, its offer an heterodox reading about the problem analyzed.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

Air quality is a topic of growing relevance on the global agenda. Two key indicators of air quali-ty, nitrogen dioxide (NO2) and carbon monoxide (CO), represent significant hazards to human health and the environment putting the sustainability of natural resources at risk. Therefore, it is imperative to regularly monitor and reduce atmospheric pollutant concentrations to mitigate their harmful consequences. This study presents an analysis of NO2 total and CO emissions in Argentina, utilizing remote sensing data. The research aims to determine the spatiotemporal distribution of NO2 and CO emissions in Argentina from 2019 to 2021. Subsequently, it seeks to establish the influence of land uses and land cover on the emission of NO2 and CO through dif-ferent climatic, anthropic, and natural indicators. The study was carried out in Argentina during the period 2019-2021, where random points were placed for the different land covers with a total of 800 points surveyed. The year with the highest CO concentration (mol/m-2) was 2020. The values were highest for tree covers and herbaceous wetland coverage in the northern part of the country. For total NO2, the highest concentrations were reached during the years 2020 and 2021. Regarding its distribution, throughout the evaluated period, the highest concentrations of total NO2 were found in the built-up and cropland coverages, with the capital of the country and the northern region of the Buenos Aires province being the most affected areas. In addition, the concentration of CO was influenced by climatic variables (atmospheric pressure, wind speed, maximum environment temperature, Palmer index), natural (height, humidity, NDVI), and ur-ban variables (distances to mining extraction, airports, power plants, urban index) for the differ-ent uses and land covers. Finally, the concentrations of total NO2 were influenced by climatic variables (Palmer index and wind speed), natural (height and NDVI), and urban variables (dis-tance to airports, power plants, industries, service stations, and open dumpsites) for the differ-ent uses and land cover. This study contributes to sustainable environmental management, ena-bling the formulation of effective strategies for mitigating emissions and promoting the long-term health and well-being of communities.

Today's city needs more than ever methodological devices that ensure a specific urbanism, in keeping with the complexity of relationships that occur in the urban space. Networks or systems of diverse nature must be activated to achieve a certain success of the city, even more so in its fragile central fabrics. The study is focused on the historic neighborhoods of the city of Jaén (Spain), which have a high vulnerability index. The aim is to establish a strategy to revitalize their urban and social capital and improve their articulation with the rest of the urban and territorial structure. A methodological proposal for the analysis of vulnerability factors and an urban and cartographic analysis of the public space is addressed through an interweaving of a triple network: environmental, social, and urban. For this purpose, the configuration of this overlapping network of analysis and formulation of criteria is presented, which considers the urban multiplicity and promotes new dynamics for the integrated urban regeneration of the area and for the activation of public and collective urban spaces.

A modular switched-capacitor (SC) DC-DC converter (MSCC) is introduced in this paper. It is designed to boost a low input voltage to a high voltage level and can be applied for photovoltaics and electric vehicles. This topology has high extensibility for high voltage gain output. The merits of the converters also lie in the fault tolerance operation and the voltage regulation with a minimum change in the duty ratio. Those features are built in when designing the modules and then integrating these into the DC-DC converter. Converter performance including voltage gain, voltage and current stress are focused and tested. The converter is modelled analytically, and its control algorithm is analyzed in detailed. Both simulation and experiment are carried out to verify the topology under normal operation and fault mode operation.

In this paper, we consider a make-to-order supply chain which satisfies demand that is dependent on both price and quoted lead -time. The manufacturer chooses the lead -time and the order quantity, and the retailer sets the revenue shares. The interactions between the manufacturer and the retailer are modelled as a Nash Game, and the existence and uniqueness of pure strategy equilibrium are demonstrated. A mechanism that enables the supply chain to coordinate the decisions of the members is developed. Lastly, we also analyze how the supply chain system parameters impact the optimal supply chain decisions and the supply chain performance.

Arabinoxylans (AXs) are non-starch polysaccharides with complex structures naturally occurring in grains (i.e., barley, corn, and others) providing many health benefits, especially as prebiotics. AXs can be classified as water-extractable (WEAX) and water-unextractable (WUAX) based on their solubility, with properties influenced by grain sources and extraction methods. A large body of evidence shows that AXs exert an im-portant health impact, including glucose and lipid metabolism regulation and immune system enhancement, which is induced by the interactions between AXs and the gut microbiota. Recent research underscores the dependence of AX physiological effects on structure, advocating for a deeper understanding of struc-ture-activity relationships. While systematic studies on WEAX are prevalent, knowledge gaps persist re-garding WUAX, despite its higher grain abundance. Thus, this review reports recent data on WUAX struc-tural properties (chemical structure, branching, MW) in cereals under different treatments. It discusses WUAX applications in baking and its benefits deriving from gut fermentation.

This study presented a novel and sustainable method for producing chitin nanocrystals (PA-ChNCs) using phosphoric acid hydrolysis. The produced PA-ChNCs were used as stabilizers for Pickering emulsions and their physicochemical properties as well as stabilization mechanisms were systematically investigated. The PA-ChNCs exhibited small particle sizes and high surface areas, enabling an effective adsorption at the oil/water interface, which prevented coalescence in Pickering emulsions. The particle size and surface charge PA-ChNCs were strongly pH-dependent, which were critical factors for stabilizing Pickering emulsions. The study showed that emulsions with higher O:W ratios (50%) exhibited larger droplets but greater viscosity, forming a stable gel-like matrix that was more stable than emulsions with other O:W ratios after storage for 30 days. Emulsions with higher PA-ChNCs concentrations (2.0 wt%) and higher pH values (pH 10) showed small droplets and high viscosity, leading to stable emulsions. This research contributes to the development of sustainable and effective emulsifiers for use in the food industry, making utilization of seafood waste in an eco-friendly manner possible. Overall, this study highlights the potential of using newly developed PA-ChNCs as stabilizers for Pickering emulsions in food products.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

Bearings are widely used in various types of electrical machinery and equipment. As their core components, failures will often cause serious consequences . At present, most methods of parameter adjustment are still manual adjustment of parameters. This adjustment method is susceptible to prior knowledge and easy to fall into the local optimal solution, failing to obtain the global optimal solution and requires a lot of resources.Therefore, this paper proposes a new method of bearing fault diagnosis based on wavelet packet transform and convolutional neural network optimized by simulated annealing algorithm.The experimental results show that the method proposed in this paper has a more accurate effect in feature extraction and fault classification compared with traditional bearing fault diagnosis methods. At the same time, compared with the traditional artificial neural network parameter adjustment, this paper introduces the simulated annealing algorithm to automatically adjust the parameters of the neural network, thereby obtaining an adaptive bearing fault diagnosis method. To verify the effectiveness of the method, the Case Western Reserve University bearing database was used for testing, and the traditional intelligent bearing fault diagnosis method was compared. The results show that the method proposed in this paper has good results in bearing fault diagnosis. Provides a new way of thinking in the field of bearing fault diagnosis in parameter adjustment and fault classification algorithms

The apple leaf-curling midge, Dasineura mali Kieffer (Diptera: Cecidomyiidae), is an invasive pest of apple. To provide crucial information for its pest risk analysis, forecast and management, we investigated the effects of temperatures (5, 10, 15, 20 and 25°C) and daylengths (10, 11, 12, 13, 14 and 15 hrs) on its development and survival. The midge could not complete its development at 10°C or lower. After transferred from 20°C to 10°C, mature larvae could survive for about two months and develop to adults. Pupation and emergence rates were significantly higher at 20°C than at 10°C and 25°C. Daylength had no effect on these parameters. The low temperature threshold and thermal requirement to complete development from eggs to adults were 3.7°C and 627 degree-days, respectively. The midge had significantly lower thermal requirement for completion of its lifecycle at 20°C (614.5 degree-days) than at 15°C (650.1 degree-days) and 25°C (634.8 degree-days). The thermal model developed in this study provided accurate predictions of the number of D. mali generations and adult emergence time in each generation in different regions of New Zealand. We suggest that the model could be used to predict population dynamics of this pest in other parts of the world.

Neural decoding from spiking activity is an essential tool for understanding the information encoded in population neurons, especially in applications like brain-computer interface (BCI). Various quantitative methods have been proposed and have shown superiorities under different scenarios respectively. From the machine learning perspective, the decoding task is to map the high-dimensional spatial &amp; temporal neuronal activity to the low-dimensional physical quantities (e.g., velocity, position). Because of the complex interactions and the abundant dynamics among neural circuits, good decoding algorithms usually have the capability of capturing flexible spatiotemporal structures embedded in the input feature space. Recently, the Transformer-based models are widely used in processing natural languages and images due to its superior performances in handling long-range and global dependencies. Hence, in this work we examine the potential applications of Transformers in neural decoding and introduce two Transformer-based models. Besides adapting the Transformer to neuronal data, we also propose a data augmentation method for overcoming the data shortage issue. We test our models on three experimental datasets and their performances are comparable to the previous state-of-the-art (SOTA) RNN-based methods. In addition, Transformer-based models show increased decoding performances when the input sequences are longer, while LSTM-based models deteriorate quickly. Our research suggests that Transformer-based models are important additions to the existing neural decoding solutions, especially for large datasets with long temporal dependencies.

Despite the rapid adoption of bilingual programs (English-Chinese) in China's higher education institutions (HEIs), concerns have been raised on perceived language hindrance to students’ academic comprehension and then performance. In response to this, this paper investigates the effects of bilingual instruction on content-based learning and provides empirical evidence after testing related influential factors in bilingual environment. Analyzing a sample of 498 undergraduate students enrolling in a fundamental business course in a sample university in China, we find insignificant statistical difference in students' academic performance between bilingual and L1 classes. We attribute this to the English language support provided by the university and show that learning competence can help students to minimize language barrier and furthermore solve the common learning problems confronted by both bilingual and L1 students. Overall, our paper aims to identify key determinants of students' academic performance in bilingual instruction and provide policy implication for developing desirable bilingual programs in HEIs.

Unmanned aerial vehicles (UAVs) have increasingly become integral to multi-access edge computing (MEC) due to their flexibility and cost-effectiveness, especially in the B5G and 6G eras. This paper aims to enhance the Quality of Experience (QoE) in large-scale UAV-MEC networks by minimizing the shrinkage ratio through optimal decision-making in computation mode selection for each user device (UD), UAV flight trajectory, bandwidth allocation, and computing resource allocation at edge servers. However, the interdependencies among UAV trajectory, binary task offloading mode, and computing/network resource allocation across numerous IoT nodes pose significant challenges. To address these challenges, we formulate the shrinkage ratio minimization problem as a mixed-integer nonlinear programming (MINLP) problem and propose a two-tier optimization strategy. To reduce the scale of the optimization problem, we first design a low-complexity UAV partition coverage algorithm based on the Welzl method and determine the UAV flight trajectory by solving a Traveling Salesman Problem (TSP). Subsequently, we develop a coordinate descent (CD) based method and an alternating direction method of multipliers (ADMM) based method for network bandwidth and computing resource allocation in the MEC system. The CD-based method is simple to implement and has a low computational complexity, while the ADMM-based method can further enhance the optimization result through joint optimization. Extensive simulations demonstrate that our proposed algorithms perform well in large-scale edge networks and outperform other representative benchmark methods.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

Avian Influenza viruses (AIVs) has posed a significant pandemic threat since their discovery. This review mainly focuses on the epidemiology, virology, and pathogenesis, and treatments of avian influenza viruses. We delve into the global spread, past pandemics, clinical symptoms, severity, and immune response related to AIVs. The review also discusses various control measures, including antiviral drugs, vaccines, and potential future directions in influenza treatment and prevention. Lastly, by summarizing the insights from the previous pandemic control, this review aims to direct effective strategies for managing future influenza pandemics.

In real financial markets, the certainty equivalent rate is an important factor for investors to consider. From the value of a specific company’s certainty equivalent rate, investors can judge if this company is worth investing in. In this paper, we will explore how to obtain the value of the certainty equivalent rate so that we can evaluate a given company. First, we will introduce the theoretical support of this paper, which is put-call parity. From put-call parity, we will derive the mathematical expression for the certainty equivalent rate. Second, we will use the mathematical expression for the certainty equivalent rate to perform an empirical study. We will consider some extreme examples, including some of the best- and worst-performing stocks up to this point in 2023. Based on these stocks’ data, we will visualize the performance of these stocks and explain the meaning of the data. Finally, we will apply the results to a very popular industry—the electric vehicle industry—to explore the current electric vehicle market situation in the U.S.A.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), the causative agent of coronavirus disease 2019 (COVID-19) continues to wreak havoc threatening the public health services and imposing economic collapse worldwide. Tailoring public health responses to the SARS-CoV-2 pandemic depends on understanding the mechanism of viral replication, disease pathogenesis, and accurately identifying acute infections and mapping the spreading risk of hotspots across the globe. However, effective identification and isolation of persons with asymptomatic and mild SARS-CoV-2 infections remain the major obstacles to efforts in controlling the SARS-CoV-2 spread and hence the pandemic. Understanding the mechanism of persistent viral shedding, reinfection, and the post-acute sequalae of SARS-CoV-2 infection (PASC) is crucial in our efforts to combat the pandemic and provide better care and rehabilitation to survivors. Here we present a living literature review on SARS-CoV-2 viral persistence, reinfection and PASC. We also highlight potential areas of research to uncover putative links between viral persistence, intra-host evolution, host immune status, and protective immunity to guide and direct future basic science and clinical research priorities.

Aimed to obtain purple garlic varieties, 360 bolting bulbs from the Protected Geographical Indication (PGI) “Las Pedroñeras” were selected for their size, and the presence of abundant external scales. After a further selection, 243 out of the 360 bulbs were discarded due to undesired characteristics, as light purple color, high number of small cloves, cloves affected by Fusarium spp. and mites, among other. It was stablished that each bulb would give rise to a family. Thus, 117 families were planted under a random design during season 2021-2022. Either physiological, morphological and phenological traits were assessed for each family, and the affectations by pest and pathogens were also controlled. After the assessment of this trial, 103 out 117 families remained in the program, and were used for the establishment of a second trial the next season. Unlike the first trial, after the evaluations only 23 families remained in the program. There was observed a high variability for most of traits, with a great influence of families. The phenotypic behavior of families was significative influenced by environment, highlighting the need of their assessment under different environmental conditions. The high variability registered for the target sample, opens the possibility to select new garlic varieties from this PGI.

Using numerical simulation method, combined with the pre-branch material characteristics of the measurement results, based on the LS-DYNA software to simulate the branch crushing process, the analysis found that not only the existence of the cutter cutting in the branch destruction process, there is also the cutting of the opposing surface of the bending fracture, with the increase in the speed of the knife rollers, the cutter cutting resistance increases, the cutting resistance reaches 2690 N when the cutter at 2500 r/min, the cutter cutting resistance is the smallest in the cutting simulation at the blade angle of 55°, the blade angle is more suitable for the cutting of the branch. In the cutting simulation under different cutting edge angles, the cutting resistance of the tool is the smallest when the edge angle is 55°, which is 1860 N. This edge angle is more suitable for branch crushing and cutting. Using Fluent software to analyse the airflow characteristics of the crushing device, it was found that with the increase of the knife roller speed, the inlet flow and negative pressure of the crushing chamber are increasing, the speed of 2500 r/min, the inlet flow and negative pressure were 1.92 kg/s and 37.16 Pa, which will be conducive to the feeding of branches, but the speed is too high and it will also lead to the enhancement of the vortex of part of the area in the crushing device, which will affect the feeding of branches and the throwing of the crushed material. affect the feeding of branches and the throwing out of crushed materials, and finally determined the speed range of the crushing knife roller is 1800 ~ 2220 r/min. Based on ANSYS/Model module modal analysis of the crushing knife roller, the knife roller of the first six orders of the intrinsic frequency and vibration pattern, crushing knife roller of the lowest order of the modal intrinsic frequency of 137.42 Hz, much larger than the crushing knife roller operating frequency of 37 Hz, the machine will not resonate during operation.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

Cadmium (Cd) is a major heavy metal pollutant and a significant cause of abiotic stress in the environment. Organisms have developed various pathways to protect themselves against Cd stress. MYB protein is a large transcription factor family in plants. Many members of the family have been found to regulate developmental processes and stress responses. However, the function and mechanism of MYB116 are far from clear. In a recent study, we found that MYB116 of Chinese cabbage enhances Cd tolerance in yeast. BrMYB116 is transiently inducible by Cd treatment in Chinese cabbage. When expressed in yeast cells, it enhances tolerance against Cd stress and reduces Cd accumulation in the cells. Further analysis shows that BrMYB116 protein enhances Cd tolerance in yeast cells by activating one target gene that encodes the facilitator of iron transport 3 (FIT3). ScFIT3 is activated through specific binding with its promoter. More importantly, the expression of ScFIT3, leads to a substantial reduction of Cd accumulation in both yeast and Chinese cabbage. This finding implies that a similar network may exist in other biological systems, which presents a promising avenue for enhancing Cd tolerance in plants and developing Cd-resistant crops.

This article is about school evaluation. The objective was to explain critically the mediating relationships between educational evaluation and the production of school knowledge from the perspective of the Dialectical Historical Materialism. With this interest, a documentary analysis was made, obtaining as result four explanatory categories: production, subsumption, distribution and exchange of knowledge, which form a concrete totality with distinctions and antagonistic relationships between them, limited by their opposite. It is concluded that the evaluation as a mediating form lacks antagonistic pair and consequently of control by opposition, emerging from the school daily as autonomous and sovereign entity, oppressive of school subjects.

The construction time of concrete structures in hydraulic tunnels is long, the construction environment is complex, and there are many influencing factors. The requirements for construction quality are high, not only to meet the strength requirements, but also to meet the design requirements of erosion resistance, crack resistance, and seepage resistance according to its specific operating environment. Therefore, evaluating the construction quality of concrete structures in hydraulic tunnels is of great significance. Considering the randomness and fuzziness of factors affecting the construction quality of concrete structures in hydraulic tunnels, this paper proposes a comprehensive evaluation model based on Combined Weighting (CWM) and Uncertainty Measurement Theory (UM). The IAHP method and CRITIC method are used to determine the subjective and objective weights of evaluation indicators, combined weighting is based on the principle of minimum entropy, and the UM method is used to evaluate the construction quality level. Finally, taking a hydraulic tunnel as an example, its construction quality grade is calculated to be III according to the evaluation model proposed in this paper, which matches with the engineering reality, and a comparative study is made with the mixture element topology theory at the same time. It is verified that the evaluation model can scientifically and reasonably evaluate the construction quality level of concrete structures in hydraulic tunnels.

Device to Device (D2D) is a pivotal technology in the next generation of communication, allowing for direct task offloading between mobile devices (MDs) to improve the efficient utilization of idle resources. This paper proposes a novel algorithm for dynamic task offloading between active MDs and idle MDs in the D2D-MEC (Mobile Edge Computing) system by deploying multi-agent deep reinforcement learning (DRL) to minimize the long-term average delay of delay-sensitive tasks under deadline constraints. Our core innovation is a dynamic partitioning scheme for idle and active devices in the D2D-MEC system, accounting for stochastic task arrivals and multi-time-slot task execution, which has been insufficiently addressed in existing literature. We adopt a queue-based system to formulate a dynamic task offloading optimization problem. To address the challenges of large action space and coupling of actions across time slots, we model the problem as a Markov Decision Process (MDP) and perform the multi-agent DRL through Multi-Agent Proximal Policy Optimization (MAPPO). We employ a centralized training with decentralized execution (CTDE) framework to enable each MD to make offloading decisions solely based on its local system state. Extensive simulations demonstrate the efficiency and fast convergence of our algorithm. In comparison with the existing sub-optimal results deploying single-agent DRL, our algorithm reduces the average task completion delay by 11.0% and the ratio of dropped tasks by 17.0%.

In recent years, frequent occurrences of low temperature disasters due to global climate change have significantly impacted the normal growth of crops. Research has indicated that inorganic selenium (which is more toxic) can not only enhance the effects of low temperature stress but also increase selenium content on plants; however, there is a scarcity of studies investigating the impacts of organic selenium and nano-selenium on crops. In order to investigate whether organic selenium and nano-selenium can enhance low-temperature tolerance and increase selenium content in pak choi (Brassica chinensis var. pekinensis. cv. ‘Suzhouqing’), different concentrations (0, 5, 10, 20 mg L-1) of exogenous selenium were applied in this experiment to assess their effects on plant growth, nutritional quality and antioxidant properties. RNA-Seq technology was used to sequence the transcriptome of the leaves. Based on the transcriptome data, a Weighted Gene Co-expression Network Analysis (WGCNA) was employed to construct a network that associates with physiological traits related to stress resistance. Two highly correlated gene co-expression modules were identified, and within them, nine hub genes associated with endocytosis, antioxidant stress, absorption, transport, and metabolism of selenium were discovered. The results indicated that the beneficial effects on yield and total selenium content under low temperature were attributed to (1) protection of photosynthetic pigments for enhancing photosynthetic capacity by the up-regulation of LHca2, LHcb1, LHca1, LHcb4 in KEGG pathway: photosynthesis-antenna proteins; (2) activation of antioxidant system for efficient ROS homeostasis such as SOD, POD and CAT by the genes such as Superoxide dismutase, Monodehydroascorbate and (3) selenium absorption by endocytosis, seleninum transportation by ABC transporter gene family and selenium metabolism related genes such as Cysteine synthase, Glutaredoxin. These findings provide a foundation for further investigation into the molecular mechanisms underlying the effects of organic selenium and nano-selenium on cyanochloride production at low temperatures.

The paper introduces a control hybrid model that is designed on the basis of OOSEM (Object-Oriented Systems Engineering Method), MDA (Model-Driven Architecture) concepts, RealTime UML/SysML (Unified Modeling Language/Systems Modeling Language), and an algorithm based on UKF (Unscented Kalman Filter). This hybrid model enables the implementation of control elements for autonomous underwater vehicles (AUVs) and can be adapted to reuse for most standard AUV platforms. To obtain this goal, the dynamic model of AUV is integrated with the following specializations of OOSEM/MDA, in which the analysis model is clarified via the use-case model definition and then combines with HA (hybrid automata) to precisely define the requirements for control. Next, the designed model is specialized via real-time UML/SysML to get the core control blocks, which describe the behaviors and structures of control parts in detail. This design model is then transformed into the model of implementation with the assistance of round-trip engineering to conveniently realize the controller of AUVs. Based on this new model, an AUV controller for low-cost turtle-shaped AUVs is implemented that performs tracking for a planar trajectory with accepted feasibility.

This paper presents a wideband dual-polarized dipole antenna structure operating at 1.7-3.8 GHz (76.4%). For a traditional 4G dipole antenna which covers the band 1.71 GHz- 2.69 GHz, it’s difficult to maintain the satisfactory impedance matching and normal stable radiation patterns within the 5G sub-6 GHz band 3.3-3.8 GHz, which mainly due to the fixed antenna height is no longer a quarter-wavelength. To solve this, a connected-ring-shaped metasurface structure is proposed and deployed to operate as an artificial magnetic conductor (AMC). As a result, stable antenna radiation patterns are obtained within the whole band 1.7-3.8 GHz. For verification, this wideband dipole antenna using AMC is implemented and tested. The measured results show that the proposed antenna has an impedance bandwidth of 80.7% (1.7-4.0 GHz). It has an average measured in-band realized gain of 7.0±1.0 dBi and a stable 70∘±5∘ half power beam width (HPBW) within the 4G/5G-sub 6GHz bands 1710-2690 MHz and 3300-3800 MHz.

In order to overcome the limitation of the traditional adaptive Unscented Kalman Filtering (UKF) algorithm in noise covariance estimation for statement and measurement, we propose a hybrid adaptive UKF algorithm based on combining Maximum a posteriori (MAP) criterion and Maximum likelihood (ML) criterion, in this paper. First, to prevent the actual noise covariance deviating from the true value which can lead to the state estimation error and arouse the filtering divergence, a real-time covariance matrices estimation algorithm based on hybrid MAP and ML is proposed for obtaining the statement and measurement noises covariance, respectively; and then, a balance equation the two kinds of covariance matrix is structured in this proposed to minimize the statement estimation error. Compared with the UFK based MAP and based ML, the proposed algorithm provides better convergence and stability.

Many research work has demonstrated that taken the Combined Cooling Heating and Power system (CCHP) as the core equipment, the integrated energy system (IES) can bring obvious benefit to energy efficiency, CO2 emission reduction and operation economy in urban areas. Compared with isolated IES, integrated energy micro-grid (IEMG) which is formed by connecting multiple regions IES together, through distribution and thermal network, can further improve the reliability, flexibility, cleanliness and economy of regional energy supply. Based on the existing IES model, this paper describes the basic structure of IEMG and built a IEMG planning model. The planning based on the mixed integer linear programming, and economically construction planning scheme are calculated by using known electricity, heating and cooling loads information and the given multiple equipment selection schemes. At last, the model is validated by a case study. The results show that the application of IEMG can effectively improve the economy of regional energy supply.

Mobile Edge Computing (MEC) integrated with Wireless Power Transfer (WPT) is emerging as a promising solution to reduce task delays and extend the battery life of Mobile Devices (MDs). Cooperative user communication, or relay technology, enhances communication efficiency for users located far from the base station by mitigating the double near-far effect caused by distance. This is considered a key technology in Beyond 5G (B5G) and future communication systems. In this paper, we focus on maximizing the long-term energy efficiency (EE) of a user-cooperation WPT-MEC system, while taking into account the uncertain load dynamics at the edge MD and the time-varying state of the wireless channel. The joint optimization of wireless charging time fraction, MD offloading duration, helper node processing time, and transfer power decision presents significant challenges due to the coupling of data offloading among cooperative users and a volatile system environment. To address these challenges, we formulate the problem as a stochastic programming problem and propose an online control algorithm, DOUCA, to solve it. Our approach utilizes Dinkelbach’s method and Lyapunov optimization theory to decouple the sequential decision problem into a deterministic sub-problem for each time slot. For the sub-problem, we use variable substitution to convert the non-convex problem into a convex one, containing only a small number of variables, which can be efficiently solved. Furthermore, we provide a mathematical analysis of our algorithm’s performance. Extensive simulation results demonstrate the effectiveness of our proposed algorithm, as evidenced by an impressive energy efficiency improvement of over 20% compared to benchmark methods. Our algorithm also achieves a trade-off between EE and system stability.

In today's highly digitized and globalized financial environment, the need to protect payment systems from risk is more urgent than ever. Artificial intelligence (AI) technology is rapidly becoming a key tool in this space, with machine learning algorithms, big data analytics, and real-time monitoring enabling AI to effectively detect and prevent fraudulent activity, optimize risk management processes, and deliver intelligent services. AI not only improves the security and efficiency of payment systems, but also significantly improves customer satisfaction and loyalty. With the continuous development of AI technology and financial payment technology, the financial payment industry will usher in more innovations and changes in the future, further optimizing the payment process, improving payment efficiency, and ensuring payment security.

In the context of freshwater ecosystems, turbidity and suspended solids play crucial roles, with their levels significantly influenced by anthropogenic activities. This study focuses on assessing and monitoring these parameters in Albufera de Valencia using Sentinel-2 imagery. The primary aim is to establish reliable estimation algorithms that can contribute to effective ecosystem management. The study calibrated and validated algorithms for estimating turbidity and suspended solids. The R783×R705/R490 model proved to have the best performance for estimating turbidity and total solids in the Albufera. However, R783/R490 obtained a higher coefficient of de-termination for the organic part, while the R705 band was selected for the inorganic part. However, to achieve better estimates of turbidity and inorganic matter, more research is needed in the future. The implications of excessive suspended solids are underscored, including the depletion of dissolved oxygen, and reduced primary productivity due to limited light penetration and habitat availability. Collaboration between disciplines such as limnology, optics and water chemistry are crucial to advance water quality estimation models in lakes and lagoons such as Albufera. By integrating expertise and approaches from these diverse fields, new knowledge can be gained and the basis for more effective management and conservation strategies can be laid.

Thin-film lithium niobate has gained significant attention in photonics due to its broad optical transparency, high refractive index, nonlinear coefficient, and substantial electro-optic coefficient. It holds great promise for developing electro-optic modulators with low loss, a compact size, and wide bandwidth. This study focuses on a meticulous investigation utilizing microwave photonics to establish a high-performance electro-optic modulator. Specifically, we analyze the optical mode field distribution and traveling wave electrode structure of lithium niobate thin-film materials. The proposed modulator achieves an impressive half-wave voltage-length product of 1.69 V·cm, a negligible metal loss of 0.01 dB/cm, and a substantial 3dB electro-optic bandwidth of 50 GHz. This research successfully realizes low-loss, high-efficiency LNOI electro-optical modulators, providing a strong foundation for large-scale integrated optoelectronic systems.

Climate change represents a prevalent challenge confronted by humanity, and with cities being one of the regions most heavily impacted by such change, enhancing their climate resilience is paramount in adapting to and mitigating the associated risks and losses. This article evaluates the climate resilience of 270 major cities in China by creating an urban climate resilience indicator system centered on exposure, vulnerability, and resilience. The article analyses the spatial and temporal evolution trend of climate resilience in Chinese cities, as well as the source of regional differences using Kernel density analysis and the Dagum Gini coefficient decomposition. The article then explores the influence of financial investments on urban climate resilience, considering the moderating effect of urbanization rate.

Motion related human activity recognition using wearable sensors can potentially enable various useful daily applications. So far, most studies view it as a stand-alone mathematical classification problem without considering the physical nature of human motions. Consequently, they suffer from data dependencies and encounter the dimension disaster problem and the over-fitting issue, and their models are never human-readable. In this study, we start from a deep analysis on natural physical properties of human motions, and then propose a useful feature selection method to quantify each feature's classification contribution capability. On one hand, the "dimension disaster" problem can be avoid to some extent, due to the affined dimension of key features; On the other hand, over-fitting issue can be depressed since the knowledge implied in human motions are nearly invariant, which compensates the possible data inadequacy. The experiment results indicate that the proposed method performs superior to those adopted in related works, such as decision tree, k-NN, SVM, neural networks.

According to official sources, the numbers of children-to-parent violence (CPV) in the most advanced countries have been on an increasing trend for more than a decade, which generates great social concern. This phenomenon has also aroused enormous interest among researchers, who have identified risk and protective factors related to adolescent CPV in numerous studies. To contribute to a better explanation of CPV, the aim of the present study was to analyze the relationship between family communication problems and CPV, through psychosocial adjustment variables -psychological distress and positive attitude toward the transgression of social norms- in schooled adolescents. The sample consisted of 8115 adolescents enrolled in schools in the State of Nuevo León (Mexico) (51.5% boys, 49.5% girls), whose ages ranged from 11 to 16 years (M = 13.34, SD = 1.04). Structural equation modeling was performed using Structural Equation Modeling Software (EQS). The results showed that family communication problems have a direct and signif-icant relationship with CPV. It was also observed that there is an indirect relationship between both variables, through the relationships of psychological distress and positive attitude towards the transgression of social norms. The multigroup analysis performed showed gender differences in some of these relationships. Finally, the results and their implications in the field of family intervention are discussed.

Antiretroviral therapy has effectively suppressed HIV infection and replication and prolonged the lifespan of HIV-infected individuals. In the meantime, various complications including type 2 diabetes associated with long-term antiviral therapy have shown steady increases. Metformin has been the front-line anti-hyperglycemic drug of choice and the most widely prescribed medication for the treatment of type 2 diabetes. However, little is known about the effects of Metformin on HIV infection and replication. In this study, we showed that Metformin treatment enhanced HIV gene expression and transcription in HIV-transfected 293T and HIV-infected Jurkat and human PBMC. Moreover, we demonstrated that Metformin treatment resulted in increased CREB expression and phosphorylation, and TBP expression. Furthermore, we showed that Metformin treatment increased the recruitment of phosphorylated CREB and TBP to the HIV LTR promoter. Lastly, we showed that inhibition of CREB activation significantly abrogated Metformin-enhanced HIV gene expression. Taken together, these results demonstrated that Metformin treatment increased HIV transcription, gene expression, and production though increased CREB phosphorylation and recruitment to the HIV LTR promoter. These findings may help design the clinical management plan and HIV cure strategy of using metformin to treat type 2 diabetes, a comorbidity with an increasing prevalence, in people living with HIV.

Recurrent pregnancy loss (RPL) affects around 2 % of women of reproductive age. Primary RPL is defined by ≥2 pregnancy losses and no normal birth delivery. In secondary RPL, the losses are after a normal pregnancy and delivery. Most cases have no clear aetiology, although primary cases are the most complex. Several gene polymorphisms have been associated with RPL. Some polymorphisms are increased in women of Asian or Caucasian race. In admixed RPL populations, the information on possible genetic links is scarce and contradictory. The study aimed to assess the frequency of two SNP in different enzymes involved in medical conditions observed during pregnancy. Microsomal epoxy hydrolase (mEPH) is involved in detoxifying xenobiotics. It is present in ovaries, and it is hormonally regulated. The endothelial nitric oxide synthase forms nitric oxide from arginine and is involved in vascular tone. Two SNPs, rs1051740 and rs1799983, were assessed. The study included 26 controls and 63 primary RPL patients. Significant differences were observed in the frequencies of both SNP (p<0.05). The frequency of mutated alleles was higher in patients. Double mutated homozygotes were encountered only in RLP patients (p<0.05). Genetic polymorphisms rs1051740 and rs1799983 may be involved in primary RPL in the Venezuelan admix population. Genetic studies could provide crucial information on the aetiology of primary RPL.

PH value is one of the most significant ecological factors affecting the survival and growth of aquatic organisms. But the effect and tolerance of pH value on many aquatic species are still unknown. This study mainly investigated the effects of pH value on the hatching rate of eggs, the adaptability of newly hatched larva fish and the survival of 3-months-old juvenile fish of Takifugu obscurus. Water pH values can cause a great impact on Takifugu obscurus lives, when the fertilized eggs of Takifugu obscurus were incubated at pH 5.0, 6.0, 7.0, 8.0, 8.3 (control group), 9.0, 10.0 and 11.0 respectively. Under the pH of 5.0, 6.0, 10.0 and 11.0, the hatching rate and speed is greatly reduced and the deformity rate of hatching larvae is greatly increased; When the hatch-pH value was 6.0, the acid adaption of hatched larvae was significantly enhanced, but alkali adaptation was weakened; Under the condition of pH gradient of 6.0, 6.4, 6.8, 7.0, 8.0, 8.3, 9.0, 10.0, 10.2, 10.5, 11.0 and 12.0, survival time and survival rate of juvenile fish show a significant difference. Especially when the pH value was 6.0 and 12.0, juvenile fish die immediately after swimming quickly. Within 24 h, half of the fish died at the pH of 6.4 and 10.3, and within 48 h, half died at the pH of 7.1 and 9.9. In addition, the gradual pH value group in which the pH value gradually decreased or increased had stronger acid-base adaptability and a higher survival rate than the acute experimental group. The above results show the relationship between pH value and survival of Takifugu obscurus, which can provide more reference for the introduction of Takifugu obscurus into saline-alkali land in the future. Additionally, the incubated pH value can influence the pH tolerance of Takifugu obscurus, which can be applied to the breed improvement into an appropriate water environment.

In this paper, we discuss optical properties of the topologically charged rotating black hole. We study the horizon, the photon region, the shadow of the black hole and other observables. The results show that in addition to the black hole spin parameter $a$, the other two parameters, five-dimensional mass parameter $\beta$ and electric charge $q$, are also found to affect the horzion, the photon region and the black hole shadow. In a certain range, with the increase of the three parameters, the horizon distance, shape of the photon region and the black hole shadow will all shrink. Moreover, with the increase of these three parameters, the distortion parameter $\delta_{s}$ gradually increases, while the peak of the black hole energy emission rate decreases.

Circular RNAs (circRNAs) served as covalently closed single-stranded RNAs have been proposed to influence plant development and stress resistance. Grapevine is the most economically valuable fruit crops cultivated worldwide and threaten by various abiotic stresses. Herein, we reported that a circRNA (Vv-circPTCD1) processed from the second exon of a pentatricopeptide repeat family gene PTCD1 was preferentially expressed in leaves and responded to salt and drought but not heat stress in grapevine. Additionally, the second exon sequence of PTCD1 was highly conserved but the biogenesis of Vv-circPTCD1 is species-dependent in plants. It was further found that the overexpressed Vv-circPTCD1 can slightly decreased abundance of the cognate host gene and the neighboring genes were barely affected in grapevine callus. Furthermore, we also successfully overexpressed the Vv-circPTCD1, and found that the Vv-circPTCD1 deteriorated the growth during heat, salt, and drought stresses in Arabidopsis. However, the biological effects on grapevine callus were not always consistent with that of Arabidopsis. Interestingly, we found that the transgenic plants of linear counterpart sequence also conferred the same phenotypes as that of circRNA during the three stress conditions, no matter what species. Those results imply that although the sequences are conserved, the biogenesis and functions of Vv-circPTCD1 are species-dependent. Our results indicate that the plant circRNA function investigation should be conducted in homologous species, which support valuable reference for further plant circRNA studies.

From the mid-19th century, Collegiate Gothic architecture gained prominence among American universities. Subsequently, through the efforts of American missionaries, the Collegiate Gothic style spread to Christian universities in Asia. Specifically, this study concentrates on the nuanced relationship between the transnational missionary routes and adopting the Collegiate Gothic style, primarily focusing on Anderson Hall at Soochow University, China. The investigation meticulously dissects the multifaceted factors influencing the choice of architectural styles, considering the perspectives of missionaries, architects, and other key stakeholders. Through an intricate analysis of Anderson Hall, this research illuminates the unique characteristics of Collegiate Gothic architecture. By unraveling the complex layers of East Asian campus heritage, this study enriches our comprehension of its origins. It establishes a robust foundation for guiding the preservation and revitalization of architectural styles within university campuses. This scholarly inquiry holds particular significance for experts in academic heritage conservation.

In recent years, the analysis of macro- and micro-expression has drawn the attention of researchers since they provide visual cues of an individual's emotions for a broad range of potential applications such as lie detection and criminal detection. In this paper, we address the challenge of spotting facial macro- and micro-expression from videos and present compelling results by using a deep learning approach to analyze the optical flow features. Different from other deep learning approaches that are mainly based on Convolutional Neural Networks (CNNs), we propose a Transformer-based deep learning approach that predicts a score indicating the probability of a frame being within an expression interval. In contrast to other Transformer-based models that achieve high performance by being pre-trained on large datasets, our deep learning model, called SL-Swin, which incorporates Shifted Patch Tokenization and Locality Self-Attention into the backbone network Swin Transformer, effectively spots macro- and micro-expressions by being trained from scratch on small-size expression datasets. Our evaluation outcomes surpass the MEGC 2022 spotting baseline result, obtaining an overall F1-score of 0.1366. Additionally, our approach also performs well in the MEGC 2021 spotting task with an overall F1-score of 0.1824 and 0.1357 on CAS(ME)^2 and SAMM Long Videos, respectively. The code is publicly available on GitHub (https://github.com/eddiehe99/pytorch-expression-spotting).

Edible insects can diversify diets, improve livelihoods, contribute to food and nutrition security, and have a smaller ecological impact. European Union has categorized insects as novel food, and recently, in 2021 and 2022, two species: Tenebrio molitor and Acheta domesticus have been authorized for commercialization. Acceptance and perception of food risk derived from insect consumption vary depending on factors impacting insect consumption acceptability, including neophobic tendencies, gender differences, familiarity, and gastronomic perceptions. The aim of this work was to evaluate the perception and acceptance of edible insects by exploring those factors. The study was carried out on higher education students from Universities from Valencia (Spain). Students recognize insects for their high nutritional value, particularly protein content, and have varying knowledge levels about specific nutritional components. In terms of labeling and marketing, removing health and sustainability benefits from packaging can improve consumer responses. Most respondents prefer clear labeling of insect derivatives, quality certification seals, and complete information about insect content. Students consider marketing and knowledge as significant influencers of insect consumption. In summary, the text highlights the multifaceted nature of insect consumption acceptability. These insights offer valuable perspectives on insect consumption dynamics.

Heat waves represents a major concern for the tourism industry in the Mediterranean area. Therefore, it is necessary to deepen the study of the influence of high temperatures and their effects on tourist behavior. This research aims to develop a structural model that allows measuring how heat waves affect the behavior of external tourist demand in coastal destinations. The results are useful for the design by tourist destinations of adaptation measures to climate change. The proposed hypotheses have been contrasted using non-linear structural equations (SEM), estimated with data from the National Institute of Statistics on external demand in Spain. The results confirm lower tourist flows with the increase in high temperatures to the coasts of the Spanish Mediterranean area from traditional source markets, such as the United Kingdom. Furthermore, the tourist flow to the Balearic Islands decreases with high temperatures.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

We investigate and discuss in detail the structure of the restricted singular value decomposition for a tensor triplet under t-product (T-RSVD). The algorithm is provided with a numerical example illustrating the main result. For applications, we consider color image watermarking processing with T-RSVD.

This study examines the DCMA concerning the future risk of the water security status. We considered three risk factors: population growth, economic growth, and natural water supply demand differences. In the risk analysis part, we consulted with experts from several sectors including academia, Non-Governmental Organization (NGOs), and industry, to predict that the probability of future water stresses in high, medium, and low scenarios are 0.73, 0.24, and 0.03, respectively. In the decision analysis part, we adopted two Multiple Criteria Decision Analysis (MCDA) approaches that include Multiple Attribute Value Theory (MAVT) and Analytic Hierarchy Process (AHP) methods to evaluate the best alternative decision to alleviate future water stresses in the DCMA. The sensitivity analysis demonstrates the best option closely connects to the weighting scheme of the criteria considered in the framework. This study provides a valuable risk and decision analysis framework to analyze the water security status associated with the future water supply and demand gap decrease caused by three risk factors: population growth, climate change, and natural water supply.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

LCK, a member of the Scr kinase family, is a non-receptor tyrosine kinase involved in immune cell activation, antigen recognition, tumor growth, and cytotoxic response. The enzyme has usually been linked to T lymphocyte activation upon antigen recognition. Lck activation is central to CD4, CD8, and NK activation. However, recently, it has become clearer that activating the enzyme in CD8 cells can be independent of antigen presentation and enhance cytotoxic response. The role of Lck in NK cytotoxic function has been controversial in a similar fashion as the role of the enzyme in CAR T cells. Inhibition of Lck has been mainly to treat hematologic malignancies with a high rate of success. They may be useful in treating other tumor types, and they may be useful to prevent cell exhaustion. New, more selective inhibitors have been documented, and they have shown inter-esting activities not only in tumor growth but in the treatment of autoimmune diseases, asthma, and graft vs host disease. Drug repurposing and bioinformatics can aid in solving several unsolved is-sues on the role of Lck in cancer. In summary, the role of Lck in immune response and tumor growth is not a simple event and requires more research.

Using annual panel data of 46 listed commercial banks in China from 2012 to 2021 and constructing a two-way fixed-effects model, this study empirically analyzes the competition and technology spillover effects of fintech on the profitability of commercial banks. The results show that (1) in the early stages of fintech development, the competition effect is larger than the technology spillover effect; thus, it is negatively correlated with commercial banks’ profitability. However, with the spread of innovative fintech, the technology spillover effects and commercial bank profitability will gradually improve. (2) The influence of fintech on the profitability of commercial banks differs. Compared to large commercial banks, fintech has more significant negative effects on small- and medium-sized commercial banks in the short run. However, the role of fintech for such banks will also grow in the future. The results of this study provide practical guidance for how commercial banks can respond to the fintech wave. To realize sustainable development of the banking industry, commercial banks should change their business philosophy and revenue model, vigorously improve their fintech innovation capability, differentiate their choice of fintech development routes, develop personalized customization with a focus on users, and ultimately realize digital transformation and upgrading.

Micro/Nano Robot is an intelligent and efficient microrobot that can perform specific tasks under the influence of external stimuli. Depending on the application scenarios, the microrobot can adaptively transform into appropriate functional forms under different external stimuli, thus perfectly matching the needs. To date, microbots have been widely used in targeted therapy, drug delivery, tissue engineering, environmental remediation, and other fields. Although the applications of microrobots are promising, there are only a few reviews that can focus on the preparation methods and driving mechanisms. Therefore, it is necessary to outline the current status of the development of these microrobots in order to provide some new insights for the further development of the field. Therefore, this paper reviews the research progress of microrobots in terms of preparation methods, stimulus response mechanisms and applications, and highlights the applicability of different preparation methods and stimulus types. Finally, the current challenges faced by microrobots are highlighted and possible solutions are proposed to facilitate the practical application of microrobots.

We primarily investigate the existence of solutions for fractional neutral integro-differential equations subjected to Neumann-type boundary conditions, which is crucial for understanding natural phenomena. Taking into account factors such as neutral type, fractional-order integrals, and fractional-order derivatives, we employ probability density functions, Laplace transforms, and resolvent operators to formulate a well-defined concept of a mild solution for the specified equation. Following this, by integrating fixed point theorems, we establish the existence of mild solutions under more relaxed conditions.

During March and April 2020, the European Union (EU) was the center of the COVID-19 pandemic. Many National Governments imposed severe lockdown policies to mitigate the health crisis. The European Parliament commissioned a survey to analyse the citizens’ attitudes over a number of issues related to the COVID-19 pandemic. 21804 European citizens in 21 EU countries responded the survey between 23 April and 1 May 2020. The paper analyses empirically the individual satisfaction that European citizens have experienced over the measures taken by the respective National Governments to control the COVID-19 pandemic. The analysis is based on a micro-econometric model (ordered probit) that explains the citizens’ satisfaction by a number of attitudes and sociodemographic factors. Our results reveal that Spaniards are the least satisfied citizens in comparison with Danes, Irelanders, Greeks and Croats who are the most satisfied nationals. The years of education and the social class also play a determinant role. We also find that the most important determinant is the political support to the Government, and that those who are more worried by the economy and the protection of individual rights are usually more critic with the measures than those who are more worried by the health consequences.

In this study, we present a federated learning approach that combines a multi-branch network and the Oort client selection algorithm to improve the performance of federated learning systems. This method successfully addresses the significant issue of non-iid data, a challenge not adequately tackled by the commonly used MFedAvg method. Additionally, one of the key innovations of this research is the introduction of uniformity, a metric that quantifies the disparity in training time amongst participants in a federated learning setup. This novel concept not only aids in identifying stragglers but also provides valuable insights into assessing the fairness and efficiency of the system. Experimental results underscore the merits of the integrated multi-branch network with the Oort client selection algorithm and highlight the crucial role of uniformity in designing and evaluating federated learning systems.

(1) Background: Parents of children with autism spectrum disorders often experience psychological distress, which can affect the quality of childcare they provide. It is crucial to screen for psychiatric symptoms among these parents. The Core Symptom Index (CSI) is a widely used tool for assessing general symptoms such as depression, anxiety, and somatic symptoms, with demonstrated validity and reliability across various populations. However, there is limited research on the validity and reliability of the CSI in the general Chinese population. This study aimed to investigate the psychometric properties of the Chinese version of the CSI among parents of children with autism spectrum disorders using Confirmatory Factor Analysis (CFA). (2) Methods: A total of 794 Chinese parents raising children with autism participated in this study. All completed the CSI, along with the social inhibition subscale of the Interpersonal Problems Inventory and the Couple Satisfaction Index. Factorial validity was assessed using CFA to determine how well the bifactor three-factor model fits the data. Various structural models were compared using model fit indices. Convergent and discriminant validity were examined by exploring correlations with the social inhibition subscale and the Couple Satisfaction Index. Invariance testing of the CSI was conducted across multiple groups based on gender, age, and education using CFA. The reliability of the CSI was evaluated using McDonald’s omega coefficients. (3) Results: The bifactor model emerged as the best-fitting model for the data, suggesting that the total score of the CSI adequately represents overall psychiatric symptoms. The CSI exhibited significant correlations with the social inhibition subscale (r = 0.41, p &lt; 0.01) and smaller correlation coefficients with the Couple Satisfaction Index (r = -0.16, p &lt; 0.05), indicating both convergent and discriminant validity. Invariant tests supported scalar invariance levels based on gender and age but only partial invariance for education. The Chinese version of the CSI demonstrated high consistency, with McDonald's omega coefficients ranging between 0.86 and 0.95. (4) Conclusions: The bifactor model of the Chinese version of the CSI is validated, making it a suitable tool for measuring depression, anxiety, and somatization symptoms among parents of children with autism spectrum disorders. Further research on other Chinese populations is encouraged.

City marathons have evolved and grown exponentially in type and popularity, managerial complexity, for their financial impact on their host cities and for the attraction of corporate sponsors. Much research has focused on evaluating the broad economic, urban, tourist, social, sporting, and symbolic effects of city marathons on host cities. Research have not examined the importance of the contribution of sponsors to the financial stability and its implications to the overall management and further success of marathons. This article focuses on the cases of the Bank of America Chicago Marathon and the Marathon Valencia Trinidad Alfonso and examines how effective has been the contribution of their sponsors to the financial stability and its implications for the management and success of both races over time. Results show that the international success of both events –in terms of sporting participation, performance and economic impact– is closely related to the design and management of the event; the synergies between the political, business and sporting spheres that the organizational leadership of the event has made it possible to implement and, as a consequence, the support received from sponsors, which has not only provided both races with financial stability, but also has contributed to improve the management of the race.

To address the challenges associated with the difficult electromagnetic (EM) scattering computations of anisotropic dielectric-coated metallic composite targets, we proposed an efficient hybrid algorithm for simulating the EM scattering of complex targets with anisotropic dielectric coatings. This method, based on Impedance Boundary Condition (IBC), utilizes surface impedance vectors to describe the EM properties of the dielectric. It fully leverages the respective advantages of the low-frequency Method of Moments (MoM) and the high-frequency Physical Optics (PO) to achieve high-precision and rapid EM simulation of anisotropic dielectric-coated metallic composite targets. Employing boundary conditions and equivalent principles, we equivalently transform the EM scattering problem of targets with thin dielectric coatings into the radiation problem of equivalent EM current on impedance surfaces. This enables the high-precision and rapid calculation of Radar Cross Sections (RCS) for complex targets with anisotropic dielectric coatings. Using examples such as a square plate structure, a simplified aircraft, and a complex satellite model, the simulation results exhibit a high degree of agreement with full-wave numerical solutions and demonstrate a significant advantage in computational resources. This research convincingly demonstrates the accuracy and effectiveness of the proposed method.