Slope failures pose a substantial threat to mining activity due to their destructive potential and high probability of occurrence on steep slopes close to limit equilibrium conditions, often found both in open pits and in waste and tailing disposal facilities. The development of slope monitoring and modeling programs usually entails the exploitation of in situ and remote sensing data together with the application of numerical modeling, and it plays an important role in the definition of prevention and mitigation measures aimed at minimizing the impact of slope failures in mining areas. Here we present a new methodology combining satellite radar interferometry and 2D finite element modeling for slope stability analysis at a regional scale, applied within slope unit polygons. We studied a former mining area in southeast Spain, and the method proved useful in detecting and characterizing a considerably large number of unstable slopes. Out of 1,959 slope units used for the spatial analysis of the radar interferometry data, 43 were unstable, with varying values of safety factor and landslide size. Out of the 43 active slope units, 21 exhibited line of sight velocities greater than the maximum error obtained through the validation analysis (2.5 cm/year). Eventually, this work discusses the possibility of using the results of the proposed approach to devise a proxy for landslide hazard. The proposed methodology can help to provide non-expert final users with intelligible, clear and easily comparable information to analyze slope instabilities in different settings, not limited to mining areas.

Functional Data Analysis (FDA) is a relatively new field of statistics dealing with data expressed in the form of functions. FDA methodologies can be easily extended to the study of imaging data, an application proposed in Wang et al. (2020), where the authors settle the mathematical groundwork and properties of the proposed estimators. This methodology allows for the estimation of mean functions and simultaneous confidence corridors (SCC), also known as simultaneous confidence bands, for imaging data and for the difference between two groups of images. This is especially relevant for the field of medical imaging, as one of the most extended research setups consists on the comparison between two groups of images, a pathological set against a control set. FDA applied to medical imaging presents at least two advantages compared to previous methodologies: it avoids loss of information in complex data structures and avoids the multiple comparison problem arising from traditional pixel-to-pixel comparisons. Nonetheless, computing times for this technique have only been explored in reduced and simulated setups (Arias-López et al., 2021). In the present article, we apply this procedure to a practical case with data extracted from open neuroimaging databases and then measure computing times for the construction of Delaunay triangulations, and for the computation of mean function and SCC for one-group and two-group approaches. The results suggest that previous researcher has been too conservative in its parameter selection and that computing times for this methodology are reasonable, confirming that this method should be further studied and applied to the field of medical imaging.

Based on economic feasibility, renewable generators can use pumped hydro storage (PHS) to improve their profitability by performing energy arbitrage under real time pricing (RTP) schemes. In this paper, we present a new method to optimise the size and manage utility-scale wind-PV systems using PHS with energy arbitrage under RTP. The storage in the PHS is used to supply load consumption and/or energy arbitrage. Further, both load supply and power-generating systems are considered, and a genetic algorithm metaheuristic technique is used to perform the optimisation efficiently. Irradiance, wind speed, temperature, hourly electricity price, component characteristics, and financial data are used as data, and the system is simulated in 15 min time steps during the system lifetime for each combination of components and control variables. Uncertainty is considered for the meteorological data and electricity prices. The pump and turbine efficiencies and available head and penstock losses are considered as variables (not fixed values) to obtain accurate simulations. A sample application in Spain is demonstrated by performing a sensitivity analysis of different locations, electricity prices, and costs. The PHS is not worth considering with the present cost of components.

The emerging whitefly-transmitted crinivirus Tomato chlorosis virus (ToCV) causes substantial economic losses by inducing yellow leaf disorder in tomato crops. This study explores potential resistance mechanisms by examining early-stage molecular responses to ToCV. A time-course transcriptome analysis compared naïve, mock and ToCV-infected plants at 2, 7, and 14 days post-infection (dpi). Gene expression changes were most notable at 2 and 14 dpi, likely corresponding to whitefly feeding and viral infection. Gene Ontology (GO) and Kyoto Encyclopedia of Genes and Genomes (KEGG) enrichment analyses revealed key genes and pathways associated with ToCV infection, including those related to plant immunity, flavonoids and steroids biosynthesis, photosynthesis, and hormone signalling. Additionally, virus-derived small interfering RNAs (vsRNAs) originating from ToCV predominantly came from RNA2 and were 22 nucleotides in lengt. To confirm these findings, two genes involved in plant immunity, Hsp90 (heat shock protein 90) and its co-chaperone Sgt1 (suppressor of the G2 allele of Skp1) were targeted through viral-induced gene silencing (VIGS), showing potential contribution to basal resistance against viral infections since their reduction correlated with increased ToCV accumulation. This study provides insights into tomato plants responses to ToCV, with potential implications for developing effective disease control strategies.

Introduction: Osteosarcomas of the jaw (OSJ) are rare tumors with a different behavior from osteosarcomas of other bones. This study aims to analyze the clinical, pathological, and therapeutic characteristics of this type of sarcoma. Methods: a retrospective observational study of cases diagnosed with OSJ registered at the “La Paz” University Hospital (Madrid). Results: Eight cases with a diagnosis of OSJ were obtained in a study period of 22 years (2000-2022). The mean age was 41 years. The distribution was 1:1 between the maxilla and mandible. Painful inflammation was the most frequent clinical manifestation. Conventional osteoblastic osteosarcoma was the most common. Survival at 5 years was 50%, while at 10 years, it decreased to 25%. Conclusions: OSJ differs from conventional osteosarcomas of long tubular bones. Surgery continues to be the mainstay of treatment; more studies are needed in which more standardized protocols can be proposed for adjuvant therapeutic management.

Abstract: Coal bed methane (CBM) reservoirs are complex systems whose properties differ from those of conventional reservoirs. Coal seams are dual-porosity systems that comprise the porosities of the matrix and cleat system. Gas in the coal seams can be stored as free gas in the cleat system and as adsorbed gas in the porous medium. The flow mechanisms of the natural gas through the formation include desorption, diffusion, and Darcy’s flow regimes. The permeability of CBM reservoirs is more sensitive to pressure variations than conventional gas reservoirs. To study the flow behavior of CBM reservoirs it is mandatory to use a model that considers their unique characteristics. The objective of this study was to propose a physical and mathematical model of production performance for horizontal wells in CBM reservoirs whose permeability is dependent on pressure. A solution for the model was obtained by applying Pedrosa´s transformation, perturbation theory, Laplace transformation, the point source method, and Sthefest´s algorithm. The solution to this problem was validated with previous work thoroughly. The type curves of the model were built and the pressure transient behavior of the model was analyzed and discussed. The effects of several parameters on pressure behavior were also discussed.

Abstract: This article aims to better understand the mechanisms that connect climate change perceptions and general willingness to engage in pro-environmental behavior using Spanish cross-sectional data (N = 403). To do this, we first developed and validated the General Willingness for Environmental Behavior Scale (GWEBS), which includes the classical approach of voluntarily doing new actions but also actions implying not doing things (degrowth) and actions forced by social constraints. The exploratory and confirmatory factor analysis showed a good fit for the one-factor structure, which had adequate validity based on their relationship with other variables. Additionally, the GWEBS distinguished between women and men, left- and right-oriented people, and people who belonged to pro-environmental groups and people who did not. In the second place, we tested the parallel mediator role of eco-anxiety and trust in science in the relationship between climate change perceptions and the GWEBS. The results showed that eco-anxiety, fully, and trust in science partially mediated such a relationship, making them crucial to mobilize the intention to act following the perception. This study contributes to our understanding of the psychological mechanisms that eventually drive pro-environmental behaviors and provides a clear direction for future research.

Cervical cancer screening systems aim to detect established HPV infections early. However, if there are no high-grade lesions, the intervention choice is basically limited to observational follow-up with recommendations on life habits like diet, to favor infection control. Therefore, it is important to establish specific feeding guidelines that provide clear evidence about the benefit they may bring against HPV infections. The present study evaluates the benefits of nutritional supplementation with a casein hydrolysate-based formula in patients with HR-HPV infection, compared with a non-supplemented control group. A total of 118 patients completed 6 months of follow-up. Significant differences between supplemented and control groups were observed for total or partial HR-HPV clearance at 6 months (74.6% vs 35.6%). Supplemented patients also suffered a lower occurrence of new intracervical lesions (0% vs 28.6%), a significantly greater resolution (67.4% vs 41.9%) and less progression of pre-existing lesions (4.7% vs 9.7%) at 6 months. An increase in the effectors of cellular immunity that could be responsible for their effect was also observed in supplemented patients. We conclude that nutritional supplementation with this casein hydrolysate-based formula could improve the outcomes of observational management of HPV infection.

This paper presents new above-ground biomass (AGB) and biomass components equations for seventeen forest species in the temperate forests of northwestern Mexico. A data set corresponding to 1336 destructively sampled oak and pine trees was used to fit the models. Generalized method of moments was used to simultaneously fit systems of equations for biomass components and AGB, to ensure additivity. Additionally, the carbon content of each tree component was calculated by the dry combustion method, in a TOC analyser. The fitted equations accounted for on average 91, 83, 84 and 78% of the observed variance in stem wood and stem bark, branch and foliage biomass, respectively, whereas the total AGB equations explained on average 93% of the total observed variance in AGB. The inclusion of h or d²h as additional predictor in the d-only based equations systems slightly improved estimates of stem wood, stem bark and total above-ground biomass, and greatly improved the estimates produced by the branch and foliage biomass equations. The fitted equations were used to estimate AGB stocks at stand level from a database on growing stock from 429 permanent sampling plots. Three machine-learning techniques were used to model the estimated stand level AGB and carbon contents; the selected models were applied to map the AGB and carbon distributions in the study area, which yielded mean values of 129.84 Mg ha^-1 and 63.80 Mg ha^-1, respectively.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

Ready-to-eat fresh fruit have an increasing presence in international markets due to its convenience and health benefits. However, these produces are highly perishable and efficient technologies to increase their shelf life are needed. In the present research, different citrus fruit species and cultivars from organic farming were assayed to obtain enzymatically citrus segments. The best results in terms of segment quality were observed for ‘Hernandina’ clementine which was chosen to make a new ready-to-eat produce based on peeled citrus segments packaged in glass jars with slight syrup made on citrus juice and organic sugar cane. The most appreciated syrup was those containing 50-50 (v/v) of ‘Fino’ lemon juice and ‘Hernandina’ clementine based on the sensory scores given by the panellists. In addition, different pasteurization treatments were assayed to preserve the new produce safety and nutritional and sensory quality properties during storage at cold temperature. Results showed that pasteurization treatment at 50 °C for 45 min could be enough to avoid microbial contamination with mesophilic and psychrophilic aerobic bacteria or yeast and mould and to maintain sensory properties until five weeks of storage at 4 °C. In addition, only a 10 % reduction of vitamin C was observed from fresh segments or syrup until the end of storage period, showing that the new ready-to-eat produce would conserve high bioactive compound content and health benefits after pasteurization and prolonged cold storage.

The utilization of inertial measurement units (IMUs) as wearable sensors is proliferating 1 across various domains such as healthcare, sports, and rehabilitation. This expansion is driven by 2 the continuous improvement of sensor technology to accommodate specific operational demands. 3 This paper introduces the development of a configurable wearable device capable of capturing both 4 high-frequency and low-frequency signals, tailored for a wide range of monitoring applications.Our 5 focus is on a comprehensive evaluation of the device in terms of deviation, noise levels, and precision. 6 We present initial findings that demonstrate the device’s robust performance, and put on the spotlight 7 the most critical optimizations needed to improve the device to reach the goal of a smart general-use 8 unit for human motion monitoring.

We study an air-fluidized granular monolayer, composed in this case of plastic spheres, which roll on a metallic grid. The air current is adjusted so that the spheres never loose contact with the grid, so that the dynamics may be regarded as pseudo two-dimensional (or two-dimensional, if the effects of sphere rolling are not taken into account). We find two surprising continuous transitions, both of them displaying two coexisting phases. Moreover, in all cases, we found the coexisting phases display strong energy non-equipartition. In the first transition, at weak fludization, a glassy phase coexists with a disordered fluid-like phase. In the second transition, a hexagonal crystal coexists with the fluid phase. We analyze, for these two-phase systems, the specific diffusive properties of each phase, as well as the velocity correlations. Surprisingly, we find a glass phase at very low packing fraction and for a wide range of granular temperatures. Both phases are characterized also by a strong anti-correlated velocities upon collision. Thus, the dynamics observed for this quasi two-dimensional system unveils phase transitions with peculiar properties, very different from the predicted behavior in well know theories for their equilibrium counterparts.

Background: The relationship between adherence to the Mediterranean Diet (MD) and both physical fitness (PF) and physical activity (PA) level has been analysed in several studies. The aim of this research was to describe, compare and analyse the level of PF and PA in schoolchildren aged 6-13 in the Region of Murcia, according to adherence to the MD. Methods: A descriptive and cross-sectional study was performed. A total of 370 schoolchildren (44.9% girls) aged 6-13 (8.7±1.8) from six primary schools in the Region of Murcia (Spain). Results: Only 25.9% of the schoolchildren had optimal adherence to the MD. Regarding the scores of the different PF tests in MD groups, only statistically significant differences were found for CRF (p=0.048) in boys. PA level, showed statistically significant differences in both boys (p=0.040) and girls (p=0.016). A positive relationship was found between the KIDMED index and CRF (ρ=.127), standing broad jump (ρ=.133) and PA level (ρ=.235). A higher probability of having a greater CRF (OR=1.17; CI95%=1.02–1.34) and PA level (OR=7.84; CI95%=2.84–21.60) was found in High MD group. Conclusion: These results suggest that an optimal adherence to the MD is associated with higher CRF and PA level in the selected schoolchildren.

A basic pattern in the body plan architecture of many animals, plants and some molecular and cellular systems is five-part units. This pattern has been understood as a result of genetic blueprints in development and as a widely conserved evolutionary character. Despite some efforts, a definitive explanation of the abundance of pentagonal symmetry at so many levels of complexity is still missing. Based on both, a computational platform and a statistical spatial organization argument, we show that five-fold morphology is substantially different from other abundant symmetries like three-fold, four-fold and six-fold symmetries in terms of spatial interacting elements. We develop a measuring system to determine levels of spatial organization in 2D polygons (homogeneous or heterogeneous partition of defined areas) based in principles of regularity in a morphospace. We found that spatial organization of five-fold symmetry is statistically higher than all other symmetries studied here (three to ten-fold symmetries) in terms of spatial homogeneity. The significance of our findings is based on the statistical constancy of geometrical constraints derived from spatial organization of shapes, beyond the material or complexity level of the many different systems where pentagonal symmetry occurs.

Large datasets play a crucial role in the progression of surgical robotics, facilitating advancements in the fields of surgical task recognition and automation. Moreover, public datasets enable the comparative analysis of various algorithms and methodologies, thereby assessing their effectiveness and performance. The ROSMA (Robotics Surgical Maneuvers) dataset provides 206 trials of common surgical training tasks performed with the da Vinci Research Kit (dVRK). In this work, we extend ROSMA dataset with two annotated subsets: ROSMAT24, which contains bounding box annotations for instrument detection, and ROSMAG40, which contains high and low level gesture annotations. We propose an annotation method that provides independent labels for the right-handed tool and the left-handed tool. For instrument identification, we validate our proposal with a YOLOv4 model in two experimental scenarios. We demonstrate the generalization capabilities of the network to detect instruments in unseen scenarios. For gesture segmentation, we propose two label categories: high-level annotations that describe gestures at a maneuvers level, and low-level annotations that describe gestures at a fine-grain level. To validate this proposal, we have designed a recurrent neural network based on a bidirectional long-short term memory layer. We present results for four cross-validation experimental setups, reaching up to a 77.35% mAP.

Based on a measuring system to determine levels of spatial organization in 2D polygons (homogeneous or heterogeneous partition of defined areas) lying on principles of regularity, we propose the entropy term linked to the concept of “information”, from the “information theory field”, in order to obtain an information measurement regarding a quantity of or amount of information in the architecture of complex 2D biological organizations. The term “quantity” does not refer to the amount of data (size), but to the probability of a geometrical basic pattern within a set of possible statistical configurations regarding levels of homogeneity and heterogeneity. It is this notion of information that is important in information theory, and measures of information in units of bits, what we propose to use for measuring quantities of organization in the architecture of complex geometrical systems. Two complex systems are tested, biological and non biological in order to obtain experimental results, which are verified with the evaluation criteria “entropy”. Experimental results show that the lowest levels of information and entropy, in addition with low rates of heterogeneity and high rates of homogeneity are particular features of geometrical organizations in biological systems.

The fast pace development of the Internet and the Coronavirus Disease (COVID-19) pandemic have impacted considerably on the educative sector; encouraging the constant transformation of the teaching-learning strategies and more in technological areas as Educational Software Engineering. Web programming, a fundamental topic in Software Engineering and Cloud-based applications, deals with various critical challenges in education, such as learning continuous emerging technological tools, plagiarism detection, generating innovative learning environments, among others. Continual change and more with the current digitization becomes a challenge for teachers and students who cannot depend on traditional educational methods. The article presents a sustainable teaching-learning methodology for web programming courses in Engineering Education using a project-based integrated approach adaptable to the continuous web technological advances. The methodology has been developed and improved for 9 years, 15 groups, and 3 different universities. Our results demonstrate that the methodology is 100% adaptable with new technologies that might arise; it also presents the advantages of avoiding plagiarism in the best case and a personalized induction for every specific student in the learning process.

From June 18 to 19, 2013, the Ésera river in the Pyrenees, Northern Spain, caused widespread damage due to flooding as a result of torrential rains and sustained snowmelt. We estimate the contribution of snow melt to total discharge applying a snow energy balance to the catchment. Precipitation is derived from sparse local measurements and the WRF-ARW model over three nested domains, down to a grid cell size of 2 km. Temperature profiles, precipitation and precipitation gradient are well simulated, although with a possible displacement regarding the observations. Snowpack melting was correctly reproduced and verified in three instrumented sites, and according to satellite images. We found that the hydrological simulations agree well with measured discharge. Snowmelt represented 33% of total runoff during the main flood event and 23% at peak flow. The snow energy balance model indicates that most of the energy for snow melt during the day of maximum precipitation came from turbulent fluxes. This approach forecast correctly peak flow and discharge during normal conditions at least 24h in advance and could give an early warning of the extreme event 2.5 days before.

Tomato is considered moderately sensitive to salinity, which detracts from the quality and yield of its fruit; therefore, wild populations have been used as a genetic resource. The aim of this research was to identify lines derived from wild tomato populations with tolerance to salinity during the germination and seedling stages. During germination, 52 wild lines and 2 commercial hybrids (Imperial®, Reserva®) were subjected to 150 mM and 0 mM NaCl and evaluated. The test was carried out for 20 days in a germination chamber with constant darkness, temperature of 25±2 °C and relative humidity of 80±4%. At the seedling stage, 22 wild tomato lines with the best performance in the germination test and 2 commercial hybrids (Imperial®, Topanga®) were evaluated for 12 days in a floating raft system. Concentrations of 175 mM and 0 mM NaCl were used. During germination, the saline condition decreased germination percentage (65.2%), speed of germination (88.2%), steam length (72.5%), root length (46.56%), normal plants number (59.5%), stem dry matter (68.78%), root dry matter (61.99%), and total dry matter (67.1%). At the seedling stage, this condition decreased (P<0.05) the aerial part dry matter (46.37%), leaf area (59.35%), root length (42.43%), final plant height (40.24%), and growth rate (71.42%). Seventeen tolerant genotypes were identified at one of both developmental stages, while one genotype showed tolerance at both stages. These results indicate that there are different response mechanisms in each developmental stage. Native tomatoes play an important role in the identification of tolerant genotypes since they can be used as genetic resources for obtaining commercial genotypes with salt tolerance.

The mucopolysaccharidoses (MPS) are a group of 11 lysosomal storage diseases (LSDs) produced by mutations in the enzymes involved in the lysosomal catabolism of glycosaminoglycans. Most of the mutations affecting these enzymes may lead to changes in processing, folding, glycosylation, pH stability, protein aggregation, and defective transport to the lysosomes. The use of small molecules, called pharmacological chaperones (PCs), that can restore the folding, trafficking and biological activity of mutated enzymes has been extensively explored in LSDs as a therapeutic alternative. PCs have the advantage of wide tissue distribution, potential oral administration, lower production cost, and fewer issues of immunogenicity. In this paper, we will review the advances in the identification and characterization of PCs for the MPS. These molecules, mainly based in molecules mimicking the enzyme substrates, have been described for MPS II, IVA, and IVB, showing a mutation-dependent enhancement of the mutated enzymes. Although the results show the potential of this strategy, further studies should focus in the development of disease-specific cellular models that allow a proper screening and evaluation of the identified PCs. In addition, in vivo evaluation, both pre-clinical and clinical, should be performed, before they can become a real therapeutic strategy for the treatment of MPS patients.

Background: Circulating tumor cells (CTC) have relevance as prognostic markers in breast cancer. However, the functional properties of CTCs or their molecular characterization have not been well-studied. Experimental models indicate that only a few cells can survive in the circulation and eventually metastasize. Thus, it is essential to identify these surviving cells capable of forming such metastases. Methods: We isolated viable CTCs from 50 peripheral blood samples obtained from 35 patients with advanced metastatic breast cancer using RosetteSepTM for ex vivo culture. The CTCs were seeded and monitored on plates under low adherence conditions and with media supplemented with growth factors and Nanoemulsions. Phenotypic analysis was performed by immunofluorescence and gene expression analysis using RT-PCR and CTCs counting by Cellsearch® system. Results: We found that in 75% of samples the CTC cultures lasted more than 23 days, predicting a shorter Progression-Free Survival in these patients, independently of having ≥ 5 CTC by Cellsearch®. We also observed that CTCs before and after culture showed a different gene expression profile. Conclusions: the cultivability of CTCs is a predictive factor. Furthermore, the subset of cells capable of growing ex vivo show stem or mesenchymal features and may represent the CTC population with metastatic potential in vivo.

Rheumatoid arthritis (RA) is an autoimmune disease mainly characterized by joint inflammation. It presents extra-articular manifestations, with the lungs one of the affected areas. Among these, damage to the pulmonary interstitium (Interstitial Lung Disease -ILD) has been linked to proteins involved in the inflammatory process and related to extracellular matrix deposition and lung fibrosis establishment. Peptidyl arginine deiminase enzymes (PAD), which carry out protein citrullination, play a role in this context. A genetic association analysis was conducted on genes encoding two PAD isoforms, PAD2 and PAD4. This analysis also included ancestry informative markers and protein level determination in samples from patients with rheumatoid arthritis, RA-associated ILD, and clinically healthy controls. Significant single nucleotide variations (SNV) and a haplotype were identified as susceptibility factors for ILD-RA development. Elevated levels of PAD4 were found in ILD-RA cases, while PADI2 showed an association with RA susceptibility. This document presents the data obtained from the conducted research, which has been published.

Objective. To test the hypothesis that a session of unilateral tSMS over the dominant primary motor cortex (M1) in healthy subjects produces a transient decrease in manual dexterity. Methods. A triple-blinded randomized control trial was conducted in 40 healthy participants who were allocated to real- or sham-tSMS group. Each participant underwent one session of tSMS and were assessed before, immediately after, 15 minutes, and 40 minutes after stimulation. Outcome measures were Finger Tapping Test (FTT), 5-seconds FTT, nine Hole Peg Test, and the hand grip assessment. Results: Significant differences were found between groups 15 minutes after stimulation in favor of the tSMS group in the FTT (2.2 ± 0.99; CI= .18-4.22; d= .84p=.034), and 5-second FTT (4.2 ± 1.98; CI= .199-8.2, d= .68; p=.04). In the intragroup analysis, a significantly lower number of taps 15 minutes after stimulation was observed in sham group (3.3 ± 1.01; CI= .47-6.13; d= .42; p=.015), but not in the real stimulation group. Conclusion: A unilateral session of tSMS in the M1 of the dominant hemisphere of healthy individuals does not reduce manual dexterity or grip strength. This technique could have benefits on the motor performance of the arm contralateral to the stimulated motor cortex

In this paper, the stabilization and high efficiency of an unstable Second Harmonic Generation (SHG) of a Nd : YVO4 laser with a KTP intracavity is carried out by using a passive Q-switching crystal and a parametric modulation method (harmonic modulation) is shown. The harmonic modulation was defined as um(t) = Amsin(2π fmt), with modulation amplitude as Am(Vpp), and modulation frequency as fm(Hz), applied to the pumping of the Nd : YVO4 -KTP laser to control the amplitude and frequency of the emission, thus stabilizing the dynamic states of this laser. The promising application of this green light source is materialized when such light is necessary for high-density optics, such as in the treatment materials industry or in some aesthetic applications.

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

The anthropogenic deterioration of aquatic ecosystems affects water resources due to agricultural malpractices, pollution from domestic septic tanks, recreational activities, and poor watershed management, among others. This study examines the management of Las Curias Reservoir (176,974 m2), San Juan, Puerto Rico, post the 2016 arrival of the invasive aquatic fern Salvinia molesta. In December 2019, a community-led initiative introduced the Cyrtobagous salviniae weevil, an effective biological control agent for S. molesta, and commenced a mechanical removal campaign using an aquatic harvester. Limnological sampling (September 2019 to March 2022) and drone flights were employed to measure physicochemical and floating plant cover changes, respectively, in the reservoir. Monitoring of weevils in the reservoir demonstrated a rapid establishment and dispersal, which resulted in visible damage including browning of plants and eventually sinking of entire mats. By January 29, 2021, 71% (125,652 m2) of the reservoir surface was covered by salvinia. In 2022, the reservoir recorded an average dissolved oxygen concentration of 2.38 mg/L -1 (± 0.021, n = 144), the highest in the study period and indicative of ecosystem recovery. After three years of control efforts, dissolved oxygen, pH, and specific conductance returned to levels recorded prior to Salvinia molesta introduction. This ecosystem recovery, a first in Puerto Rico, could be attributed to an early use of mechanical control and a long-term impact of biological control.

Background: Understanding the trophic ecology of threatened freshwater fishes is relevant to managing their conservation. The genus Orestias is endemic to the Andes region and shows great biogeographical interest in the Neotropics due to its adaptation to the high-altitude systems of the Andes as well as because several species are considered threatened. (2) Methods: Here, we synthesize the documented trophic interaction of Orestias spp. in freshwater ecosystems of the Andes region available in the literature and use available data to explore the trophic interaction of Orestias species via null models. (3) Results: Our findings showed that Orestias spp. consume a wide range of prey (i.e., mainly aquatic insects, crustaceans, and mollusks) that varied according to their habitats and feeding morphology. The null model revealed that species associations in diet were random because of the presence of many repeated species. Our results would reveal that some Orestias spp. may show an opportunistic feeding strategy that concurs with previous reports. Additionally, we highlight major information gaps associated with the trophic ecology of Orestias spp. and propose some direction for future studies. (4): Our study provides valuable in-formation on Orestias spp. trophic ecology, which may be useful for developing conservation strategies for native fish in the Neotropical region.

Reference evapotranspiration (ET0) is the first step in calculating crop irrigation demand, and numerous methods have been proposed to estimate this parameter. FAO-56 Penman-Monteith (PM) is the only standard method for defining and calculating ET0. However, it requires radiation, air temperature, atmospheric humidity, and wind speed data, limiting its application in regions where these data are unavailable; therefore, new alternatives are required. This study compared the accuracy of ET0 calculated with the Blaney-Criddle (BC) and Hargreaves-Samani (HS) methods versus PM using information from an automated weather station (AWS) and the NASA-POWER platform (NP) for different periods of time. The information collected corresponding at Module XII of the Lagunera Region Irrigation District 017, a semi-arid region in the North of Mexico. The HS method underestimated by 5.5 % the reference evapotranspiration (ET0) compared to the PM method during the period from March to August, and yielded the best fit in the different evaluation periods: daily, average, and 5-day cumulative; the latter showed the best values of inferential parameters. The information about maximum and minimum temperatures from the NP platform was suitable for estimating ET0 using the HS equation. This data source is a timely alternative, particularly in semi-arid regions where no data from weather stations are available.

Abstract: Thermal desalination is yet a reliable technology in the treatment of brackish water and seawater; however, its demanding high energy requirements have lagged it compared to other non-thermal technologies such as reverse osmosis. This review provides an outline of the development and trends of the three most commercially used thermal or phase change technologies worldwide: Multi Effect Distillation (MED), Multi Stage Flash (MSF), and Vapor Compression Distillation (VCD). First, state of water stress suffered by regions with little fresh water availability and existing desalination technologies that could become an alternative solution are shown. The most recent studies published for each commercial thermal technology are presented, focusing on optimizing the desalination process, improving efficiencies, and reducing energy demands. Then, an overview of the use of renewable energy and its potential for integration into both commercial and non-commercial desalination systems is shown. Finally, research trends and their orientation towards hybridization of technologies and use of renewable energies as a relevant alternative to the current problems of brackish water desalination are discussed. This reflective and updated review will help researchers to have a detailed state of the art of the subject and to have a starting point for their research, since current advances and trends on thermal desalination are shown.

SARS-CoV-2 is a new coronavirus that has caused a worldwide pandemic. It produces severe acute respiratory disease (COVID-19), which is fatal in many cases, characterised by cytokine release syndrome (CRS). According to the World Health Organization (WHO), those who smoke are likely to be more vulnerable to infection. Here, in order to clarify the epidemiologic relationship between smoking and COVID-19, we present a systematic literature review until 28 April 2020 and a meta-analysis. It includes 18 recent COVID-19 clinical and epidemiological studies based on smoking patient status from 720 initial studies in China, USA, and Italy. The percentage of hospitalised current smokers was 7.7% (95%CI: 6.9-8.4) in China, 2.3% (95%CI: 1.7-2.9) in the USA and 7.6% (95%CI: 4.2-11.0) in Italy. These percentages were compared to the smoking prevalence of each country and statistically significant differences were found in them all (p <0.0001). By means of the meta-analysis, we offer epidemiological evidence showing that smokers were statistically less likely to be hospitalised (OR=0.18, 95%CI: 0.14-0.23, p<0.01). CRS and exacerbated inflammatory response are associated with aggravation of hospitalise patients. In this scenario, we hypothesise that nicotine, not smoking, could ameliorate the cytokine storm and severe related inflammatory response through the cholinergic-mediated anti-inflammatory pathway.

Gold nanoparticles (AuNPs) have been used in a broad range of applications conferring to bio-molecules diverse proprieties such as deliver, stabilization and reduction of adverse effects of drugs or plant ex-tracts. Polyphenolic compounds from Bacopa procumbens (BP) are able to modulate proliferation, adhesion, migration and cell differentiation, reducing artificial scratch area in fibroblast cultures and promoting wound healing in in vivo model. Here, chemically synthetized AuNPs conjugated with BP (AuNP-BP) were characterized by Uv-Vis, ATR-FTIR, DLS and zeta-potential. Results showed over-lapping FTIR spectra of polyphenolic compounds from B. procumbens capping the AuNPs, stable size by the DLS and zeta potential, AuNP-BP was 44.58 nm, the zeta-potential of AuNPs was -36.3±12.3 mV after conjugation with the BP; - (AuNP-BP), the zeta-potential was reduced to -18-2±7.02 mV. Enhancement of wound healing effect were evaluated by morphometric, histochemical and FTIR changes in rat wound excision model. Results showed that the nanoconjugation process reduced 100 folds BP concentrations to have the same wound healing effect of BP alone. Besides histological and FTIR spec-troscopy analyses, demonstrated that AuNP-BP treatment displayed better macroscopical performance; the reduction on inflammatory cells, and the increased synthesis and better organization of collagen fibers.

Physical exercise is the greatest stress on the cardiovascular system, not only in humans but also in all vertebrates. Consequently, the cardiovascular response cannot be thought of as having only one "anthropocentric" interpretation. The modulation of cardiac output (Q) in response to exercise in the five major groups of vertebrates exhibits considerable variability. Moreover, the response of the heart rate (HR) and the stroke volume (SV), the fundamental factors that cause the rise in Q, is also highly variable. The difference in the range of HR is difficult to determine in many vertebrates, both at rest and at maximal effort. Additionally, the increase in SV varies among vertebrates. For example, while rainbow trout and leopards increase their SV by increasing end diastolic volume (EDV), humans do so at the expense of both increasing EDV and reducing end systolic volume (ESV). The variation in arterial pressure that arises during exercise varies notably among vertebrates, such as amphibians, whose blood pressure values do not increase as significantly as in mammals. Such differences in cardiovascular response among vertebrates may be linked to their habitat or living environment. This review aims to analyze the cardiovascular response of vertebrates to physical exercise as the most common stressor.

Dietary supplements are commonly used among athletes. The Australian Institute of Sport (AIS) groups supplements into 4 categories, being group D considered by the World Anti-Doping Agency (WADA) as prohibited supplements. The online availability of four doping substances: oxandrolone, dehydroepiandrosterone (DHEA), androstenedione and Tribulus terrestris, purchased from Spain, Puerto Rico, Canada, USA, Ukraine and Russia was evaluated. The characteristics of the websites, the countries the webs sold to, the pharmaceutical forms offered and the recommendations for its use were analyzed by using a computer tool designed ad hoc. There were significant differences between countries in the number of webpages that sold the products (Chi-square test, p<0.05). Oxandrolone was available for purchase mainly in Spain (27.12%) and Ukraine (26.58%), coming from websites dedicated to sports (77.26%). For DHEA, most of the pages were located in Canada (23.34%) and Russia (21.44%). Tribulus terrestris was the compound with the highest number of web pages. In the case of androstenedione, none of the pages for its sale requested prescription. Products such as androstenedione or DHEA are claimed to enhance sports performance or for sports use without providing details. The results showed that a limited number of Internet sites request prescriptions. Most of the doping substances are purchased from the country where they are requested. Athletes should be encouraged to consult health professionals about which supplements are suitable for their type of training and sports objectives.

Mexico shows a high prevalence of obesity in children and adolescents. Geographical location and cultural environment could play a role in the promotion of healthy lifestyles in terms of physical activity (PA), sedentary behavior (SB) and nutrition. The purpose of this study was to assess rural and urban differences in body composition (BC), physical fitness (PF), PA and nutritional status of adolescents from the state of Jalisco (Mexico). The study involved 469 students aged 13-17 years (55.0% girls) from 8 high schools. BC was analyzed by bioimpedance, and PF by standardized field tests. Objective measurements of PA and SB were taken in a subsample (n=240). Energy intake (EI) was calculated from two 24h recalls. Rural residents presented a higher prevalence of overweight, waist circumference, trunk fat mass, regional fat free mass and muscle handgrip strength (all p&lt;0.05, ηp2&lt;0.06). Cardiorespiratory fitness was similar among participants, whereas urban adolescents showed higher muscle power, speed-agility and flexibility scores (all p&lt;0.05, ηp2&lt;0.07). Overall lifestyle behavior in urban adolescents was more sedentary (p&lt;0.05, ηp2= 0.11). EI was similar in both locations. In conclusion, urban Mexican adolescents presented a generally higher sedentary behavior and better fitness and fatness profile than their rural peers.

Pinus occidentalis, Swartz is the primary timber species in the Dominican Republic (DR). Despite its economic importance, studies conducted on this species are very scarce, making it difficult to estimate current inventory levels. This study aims to enhance the accuracy of estimating total bole volume of P. occidentalis in different ecological zones (EZs) within La Sierra, evaluating and comparing two established volume equations—combined variable and Schumacher-Hall—across nine modeling variants (MVs). An indicator variables analysis determined the necessity of distinct equations for two EZs. Fitting included both linear and nonlinear models. Our comprehensive statistical analysis included goodness-of-fit metrics to evaluate each model variant's performance rigorously. Modeling variant SH02 was most effective in the Dry Ecological Zone, showing superior performance in both fitting and validation phases. Similarly, SH03 emerged as the best fit for the Combined Intermediate and Humid Ecological Zones, achieving the lowest overall ranking sum among tested variants. The SH equation variants SH02 and SH03, provide reliable and precise volume estimations, allowing optimization of forestry management practices for P. occidentalis trees. The SH models outperformed the CV model variants' consistency in parameter estimation. This tailored approach employed ensures more accurate volume predictions, which is crucial for sustainable management and conservation efforts.

Background: Atopic dermatitis is a chronic condition that significantly affects the daily life of those who suffer from it, requiring complex and personalized management with active participation of the patient in the management of their disease. Objective: to describe the design and development process of a mobile application, using the Design Thinking method, for the follow-up of patients with atopic dermatitis. Methods: User-centered design and prototype creation method, differentiating the phases of the empathize, define, idea, prototype, and test. A purposive snowball sampling was used to recruit patients with atopic dermatitis, family members, and health professionals. Three two-hour workshops were held, attended by 25 people. Results: the parameters to be monitored will include objective data (physical, behavioral, treatments, environmental, integration of daily routines) and subjective data (user experience). On the other hand, it will figure out behavior patterns, set up rewards, foster a feeling of community, and use notifications and a chatbot. Conclusion: The active integration of all stakeholders at each stage of the design and development of the digital solution has improved its relevance and acceptance, resulting in a tool that is expected to significantly improve the management of atopic dermatitis.

Salmonella Typhimurium infection in pigs is characterized by an intense inflammatory response in early infection which seems to dysregulate host physiology including the gut microbiota. Both, changes in host physiology and microbiome composition, must entail modifications within the gut environment. This study analyzes the gut metabolome in early infected pigs (48 hours after infection) and non-infected controls by untargeted metabolomics (LC–QTOF MS/MS and GC–TOF MS), supported with microbiome data (16S rRNA abundance and prediction functional analyses). The metabolomic profile in Salmonella-infected pigs differed from healthy controls in 39 of these metabolites, including eight amino acids, four bile acids and carboxylic acids, three carnitines and sugar derivates, eleven fatty acids and six other compounds. Changes in amino acids abundance and the observed decrease of proteolytic bacteria such as Lactobacillus or Bacteroides could favor the niche colonization by Desulfovibrionaceae. In addition, the decrease in short chain fatty acids and tricarboxylic acids cycle was correlated to a decrease in beneficial bacteria in infected pigs. Interestingly, we observed an increase of bile acids concentration and compounds such as succinic acid or pantothenic acid, which may boost the inflammatory response. Altogether, the results reveal how S. Typhimurium infection alters the gut microbiome composition and prompts changes in the metabolism with a potential interaction between intestinal metabolism and microbiota abundance.

Early diagnosis and appropriate treatments are crucial to reducing mortality risk in septic patients. Low SOFA scores and current biomarkers may not discern adequately patients that could develop severe organ dysfunction or have an elevated mortality risk. The aim of this prospective observational study is to evaluate the predictive value of the biomarkers midregional proadrenomedullin (MR-proADM), procalcitonin (PCT), C-Reactive Protein (CRP), and lactate for 28-day mortality in patients with sepsis and a SOFA score ≤ 6. 284 patients were included, with a 28-day all-cause mortality of 8.45 % (N=24). Non-survivors were older (p=0.003), required mechanical ventilation (p=0.04) and were ventilated for longer (p=0.02), had a higher APACHE II (p=0.015) and SOFA (p=0.027) scores. Lactate showed the highest predictive ability for all-cause 28-day mortality with an area under the receiver-operating characteristic curve (AUROC) of 0.67 (0.55–0.79). The AUROC for all-cause 28-day mortality in patients with community-acquired infection was 0.69 (0.57–0.84) for SOFA, and 0.70 (0.58–0.82) for MR-proADM. A 2.1 nmol/L cut-off point for this biomarker in this subgroup of patients discerned with 100% sensibility survivors from non-survivors at 28 days. In patients with community acquired sepsis and initial SOFA score ≤ 6, MR-proADM could help identify patients at risk of 28-day mortality.

We present an innovative method harnessing multistability within a diode-pumped erbium-doped fiber laser to construct logic gates. Our approach involves manipulating the intensity of external noise to regulate the probability of transitioning among four concurrent attractors. In this manner, we facilitate the realization of OR, AND, NOT, and NOR logic operations, aligning with the coexisting period-1, period-3, period-4, and period-5 orbits. Employing detrended fluctuation analysis, we establish equilibrium in the probability distributions of these states. The obtained results denote a substantial advancement in the field of optical logic gate development, representing a pivotal stride toward the seamless integration of an all-optical logic gate within laser oscillator-based systems.

Commercially pure (c.p.) iron powders with a deliberate high degree of oxidation were consolidated by medium-frequency electrical resistance sintering (MF-ERS). This is a consolidation technique where pressure, and heat coming from a low-voltage and high-intensity electrical current, are simultaneously applied to a powder mass. In this work, the achieved densification rate is interpreted according to a qualitative microscopic model, based on the compacts global porosity and electrical resistance evolution. The effect of current intensity and sintering time on compacts was studied on the basis of micrographs revealing the porosity distribution inside the sintered compact. The microstructural characteristics of compacts consolidated by the traditional cold-press and furnace-sinter powder metallurgy route are compared with results of MF-ERS consolidation. The goodness of MF-ERS versus the problems of conventional sintering when working with oxidized powders is analyzed. The electrical consolidation allows to obtain higher densifications than the traditional route under non-reducing atmospheres.

Materials known as Nd:YAG are crystalline materials of the cubic system made from neodymium-doped yttrium aluminum garnet, which among others, have excellent optical properties. Nd:YAG four-level laser devices are highly used in both the health and industrial sectors. In this study, a simple and inexpensive alternative to manufacturing Nd:YAG materials through solid state reactions following powder processing routes was proposed. For this, an intense mixture of the precursor materials (Al2O3 and Y2O3) was carried out, followed by the addition of neodymium atoms to improve the optical properties of the resulting material. High energy mechanical mixing of the precursor powders resulted in submicron particles, with good size distributions of the powders. The advance of YAG formation was monitored by intermediate phase formation during heat treatment through interrupted tests at different temperatures and analysis by X-ray diffraction. From this analysis, it was found that reaction for the formation of the desired YAG is completed at 1500°C. Fourier-transform infrared spectroscopy analyses determined the presence of functional groups corresponding to the YAG. Finally, the study by optical emission spectroscopy showed wavelengths in agreement with the electronic structure of the elements of the synthesized Nd:YAG.

Cascalote pods are an important source of phenolic compounds, mainly recovered using solvent extraction methods. As a sustainable alternative, this study aimed to evaluate solid-state fermentation (SSF) to enhance the extractability of total phenolic compounds (TPC) with antioxidant activity (AA) from cascalote pods. Aspergillus niger GH1 was selected based on the amount of TPC released and AA measured (ABTS, DPPH, FRAP) in a shorter time. Moreover, moisture, temperature, inoculum size, and mineral composition were evaluated. The largest amount of TPC released was 124.17 mg/gdm (g of dry material) after 12 h of culture, strongly and highly significantly correlated with the AA. Moisture and KH2PO4 concentration were the main influencing factors on TPC release. Treatment 6 [1x 107 spores/gdm, 30 °C, 60% moisture, mineral composition (g/L): KH2PO4, 1.52; NaNO3, 7.65; and MgSO4, 1.52] was selected due to the highest values of both TPC and AA. SSF-assisted extraction allowed increase 118 % and 93 % in TPC and AA values, respectively. Corilagin, lagerstannin, geraniin, and ellagic acid were the main phenolic compounds identified by RP-HPLC-ESI-MS in cascalote extracts. The results obtained demonstrate the feasibility of SSF-assisted extraction as a biotechnological alternative for the recovery of important bioactive molecules from this underutilized material.

Healthcare workers (HCW) have been the professional category most exposed to SARS-CoV-2. The pandemic’s impact on HCW was analyzed in terms of COVID-19-related temporary disability (TD) between February 15 2020 and May 1 2021. TDs in HCW for COVID-19 infection or quarantine were described. TD quarantine/infection ratios and TDs per 100,000 affiliated HCW were compared with the cumulative incidence (CI) of COVID-19 cases notified to the National Network of Epidemiological Surveillance. TDs rates by economic activity and occupation were computed. A total of 429,127 TDs were recorded, 36,6% for infection. Three-quarters (76%) were women. The median TD quarantine/infection ratio was 2.5 (Interquartile range [IQR] 1.5-3.9). TDs rates in HCW were always above the CI except for the last two months of the fourth wave. Hospital activities accounted for 84% of TDs and showed the highest TD rate for infection (8,279/100,000). The highest TDs rates were registered among Nursing assistants, Nursing professionals and Physicians: 7,426, 6,925 and 5,508/100,000, respectively. The results demonstrate the high impact of COVID-19 on HCW in Spain and it’s inequalities. They also confirm that TDs represent a complementary source of information for epidemiological and public health surveillance and could provide an early warning of new emerging infections.

We study the synchronous dynamics of three diffusively coupled erbium-doped fiber lasers (EDLFs) in the unidirectional ring configuration without external pump modulation. The dynamical behavior of the system is analyzed using time series, Fourier spectra, Poincaré sections, bifurcation diagrams, and Lyapunov exponents for different values of the coupling strength. For weak coupling, we observe a well-known route to chaos from a stable equilibrium through a Hopf bifurcation and a series of torus bifurcations as the coupling strength is increased. An interesting result is found for large values of the coupling strength, where the phase locking is close to zero. This allows a significant increase in the peak energy of the EDFLs pulses, i.e., above the coupling strength the lasers switch to a Q-switching mode with large-amplitude short pulses. This result allows us to propose a new method for increasing the laser pulse energy based on the control of the bistability by the rotating wave in the array of three unidirectionally ring-coupled EDFLs as a function of the coupling strength. In our system, we were able to increase the peak laser power by almost 20 times more than a continuous single EDFL.

In this work epitaxial Au islands have been grown on epitaxial α-Fe2O3 thin film by pulsed laser deposition on SrTiO3(111) substrate. Both Au and α-Fe2O3 layer show an island-type growth with an average particle size of 40 and 62 nm, respectively. The crystallographic coupling of lattices is confirmed with a rotation of 30º between the in-plane crystallographic axes of α-Fe2O3(0001) structure and those of SrTiO3(111) substrate and between the in-plane crystallographic axes of Au(111) and those of α-Fe2O3(0001) structure. α-Fe2O3 is the only phase of iron oxide identified before and after its functionalization with Au nanoparticles. In addition, its structural character-istics are also preserved after Au deposition, with minor changes at short-range order. The func-tional character of the complex systems as gas sensor has been proven at room temperature. Con-ductance measurements of Au(111)/α-Fe2O3(0001)/ SrTiO3(111) system show that the incorpora-tion of Au islands on top of the α-Fe2O3(0001) layer induces an enhancement of the gas-sensing ac-tivity for CO and CH4 gas in comparison to a bare α-Fe2O3(0001) layer grown on SrTiO3(111).

This study is dedicated to understanding and simulating the mechanical properties of concrete, with a specific focus on the mesoscopic scale. Investigating concrete at this level involves examining its composition as a heterogeneous amalgamation comprising mortar, aggregates, and the interfacial transition zone (ITZ). Such an approach provides a detailed examination of the material's behavior and attributes. Numerical models are utilized, leveraging the finite element method (FEM), to examine the behavior of concrete. The study employs MATLAB programming to develop three-dimensional models, subsequently subjected to FEM analysis. Various mesoscopic Representative Volume Elements (RVEs) are formulated, encompassing varied shapes and dimensions. The MATLAB framework generates input files for numerical FEM simulations, replicating compression strength tests. As complexity increases with the inclusion of the ITZ, prismatic RVEs are developed. The proposed mesoscopic model establishes a foundational framework for a numerical simulation methodology tailored to laboratory compression tests. It provides detailed insights into concrete behavior, elucidating deformation, and fracture mechanisms. Although not a complete substitute for experimental methods, these models offer a cost-effective and expeditious alternative, pinpointing vulnerable areas and exploring the implications of additional materials on concrete behavior. Experimental data and virtual tests pave the way for mitigating carbon footprint and improving concrete sustainability.

Background: The mental state is important in the health/illness process. Including stress, depression and anxiety. Nature immersion therapies have been implemented as a valid method for reducing these disorders. The aim will evaluate the effect of forest intervention therapies on levels of stress, depression, and anxiety. Methods: We searched for randomized clinical trials related to stress, anxiety and depression levels. Risk of bias was assessed according to the guidelines of the Cochrane Handbook for International Systematic Reviews. Results: We identified and synthesized eight publications. Two studies for cortisol showed significant differences between the pre-test and post-test levels in the intervention groups. One study including Natural killer cells, that reported a significant decrease in the intervention group compared to the control group. Two studies used the Stress Response Inventory, indicated a significant reduction in stress levels in the intervention group compared to the control group. Regarding Restorative Out-come Scale, no significant differences were found. Three studies were selected for the evaluation of anxiety and depression levels according to the Positive and Negative Affect Schedule. Four studies used The Profile of Mood States scale; no significant difference was observed. Conclusions: There is limited evidence to recommend forest bathing for reducing these disorders.

Cervical cancer is preventable through vaccination, early detection, and treatment of precancerous lesions. However, global inequalities mean that the disease remains a leading cause of cancer death around the world, with over 80% of new cases and 90% of deaths occurring in low and middle-income countries (LMICs). In El Salvador, joint efforts between the Ministry of Health (MoH) and the non-profit organization Basic Health International (BHI) have been in place since 2008 with the goal of reducing the country’s disease burden. While the World Health Organization’s (WHO) call to action to eliminate cervical cancer provided worldwide momentum to implement new public health initiatives, the COVID-19 pandemic disrupted ongoing programs and jeopardized plans for the future. The purpose of this manuscript is to describe the progress that El Salvador has achieved in improving cervical cancer prevention, the impact of the pandemic on current strategies, and potential solutions that can help the country meet the WHO’s strategic targets by 2030 to accelerate the elimination of cervical cancer.

Osteoarthritis (OA) is the most common cause of pain and disability in adults. Dietary supplements such as undenatured type II collagen (UC-II) have shown to have some benefits in OA treatment. This study aimed to assess changes in pain levels among knee OA patients treated with UC-II for 6 months. Patients with knee OA of any grade were given a daily 40 mg dose of UC-II (CondroArtil®) as a dietary supplement for 6 months. Pain levels were measured using the visual analog scale (VAS) before starting UC-II 6 months thereafter. A total of 100 patients (62/38: male/female) with a mean age of 46.3 ± 13.8 years participated in the study. Most patients (60%) had mild to moderate OA (grade I or II). The UC-II supplementation was shown to significantly reduce pain levels (p<0.001) with a negative correlation between pain reduction and age (p=0.006) and BMI (p=0.049). The OA severity also affected pain reduction (p=0.011), with grade II OA experiencing higher pain levels. Previous physical therapy and food supplements had a significant impact on pain reduction (p=0.017 and p=0.012, respectively). The study suggests that UC-II is an effective treatment for reducing pain in patients with knee OA.

There is currently much interest in avoiding precious metals in Catalysis. The devel-opment of nickel catalysts to replace palladium in the Mizoroki-Heck reaction is a relevant case in this line of research since both elements share many chemical features. This contri-bution focuses on -Phenyl elimination in alkylnickel complexes. This is the microscopic reverse of olefin insertion (or carbometallation), a fundamental step of the Heck cycle that is usually considered irreversible and selectivity-determining. However, the potential reversibil-ity of carbometallation is generally concealed by the facile beta-hydrogen elimination that follows. Where -hydrogen elimination is hindered, beta-aryl elimination may ensue. We have previously shown that cationic 2-methyl-2-phenylpropyl (neophyl) palladium com-plexes supported by bidentate ligands experience -Ph elimination, which can be seen as an example of olefin de-insertion. In this contribution, we report that -phenyl elimination can also occur in their nickel analogs, in which case fast hydrolyses of the resulting phenyl product can follow the reaction. We investigated the mechanism of these processes and compared their feasibility for nickel and palladium catalysts using DFT calculations. These results are relevant information for the design of nickel-based catalysts for the Heck reac-tion.

High-resolution GPS/GSM dataloggers provide spatial information of the highest quality, which outperform previous tracking methods, such as Argos telemetry or conventional VHF ground-tracking. As a result, this has improved our knowledge of home-range behavior and spatial ecology of many species, including large raptors. In this paper, we use high-resolution GPS/GSM dataloggers to assess the home-range size and the role of sex, season (breeding or non-breeding season), and breeding status (reproductive or non-reproductive individuals) on the space use of Bonelli’s eagle (Aquila fasciata). To this end, 51 territorial individuals (25 females and 26 males) were equipped with GPS/GSM transmitters and were tracked over 7 years (2015–2021) in eastern Spain. Overall, we recorded 4,791,080 fixes that were analyzed through kernel density methods (50%, 75%, and 95% fixed kernels). The average individual home-range size according to the 95%, 75%, and 50% kernels was 54.84 ± 20.78 km², 24.30 ± 10.18 km², and 11.17 ± 4.90 km², respectively. Overall, the home-range size of individuals occupying the same territory was similar, mainly due to the cooperative hunting behavior exhibited by the species. We did not find interannual differences in the home-range size (95% fixed kernel) of the majority of individuals, showing a strong territorial fidelity of the breeding pairs. In general, females’ home-range size was slightly smaller than males’ size due to the decrease in activity in the breeding season as a result of laying, incubation, and chick attendance at nests. No seasonal variation in the 95% kernel was found, but it was found in the 75% and 50% kernels. In regard to the breeding status, higher home-range size was recorded in the non-reproductive individuals. Moreover, we found a low neighbor overlap among the territories (4.18% ± 3.06%), which evidences a high level of intraspecific competition in the Bonelli’s eagle. Finally, this study highlights the advantages of the use of accurate telemetry information to improve our understanding of the spatial ecology of the endangered Bonelli’s eagle, which ultimately will serve to better inform management actions for its conservation.

In this work we discuss the insights from activity landscape, docking and molecular dynamics towards the understanding of the structure-activity relationships of dual inhibitors of major epigenetic targets: lysine metiltransferase (G9a) and DNA metiltranferase 1 (DNMT1). The study was based on a novel data set of 50 published compounds with reported experimental activity for both targets. The activity landscape analysis revealed the presence of activity cliffs, e.g., pairs of compounds with high structure similarity but large activity difference. Activity cliffs were further rationalized at the molecular level by means of molecular docking and dynamics simulations that led to the identification of interactions with key residues involved in the dual activity or selectivity with the epigenetic targets.

Self-consciousness can be considered as the internal disposition to direct attention to oneself. This dispositional tendency can be focused on private aspects of the self, but also on public characteristics of the individual. We examine self-consciousness in online consumer behavior. This concept has been poorly investigated in consumer research. The main objective of this paper is to analyze the influence of the dimensions of self-consciousness in consumer adoption of online shopping. This study is based on a sample of 725 Spanish undergraduates. Results indicated that public self-consciousness is a significant predictor of the adoption of online shopping.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

Transient receptor potential canonical (TRPC) channels are calcium channels with diverse expression profiles and physiological implications in the retina. Neurons and glial cells of rat retinas with photoreceptor degeneration caused by retinitis pigmentosa (RP) exhibit basal calcium levels that are above those detected in healthy retinas. Inner retinal cells are the last to degenerate and are responsible for maintaining the activity of the visual cortex even after complete loss of photoreceptors. We considered the possibility that TRPC1 and TRPC5 channels might be associated with both the high calcium levels and the delay in inner retinal degeneration. TRPC1 is known to mediate protective effects in neurodegenerative processes, while TRPC5 promotes cell death. In order to comprehend the implications of these channels in RP, the co-localization and subsequent physical interaction between TRPC1 and TRPC5 in healthy retina (Sprague-Dawley rats) and degenerating (P23H-1, a model of RP) retina were detected by immunofluorescence and proximity ligation assays. There was an overlapping signal in the innermost retina of all animals where TRPC1 and TRPC5 physically interacted. This interaction increased significantly as photoreceptor loss progressed. Both channels function as TRPC1/5 heteromers in the healthy and damaged retina, with a marked function of TRPC1 in response to retinal degenerative mechanisms. Furthermore, our findings support that TRPC5 channels also function in partnership with STIM1 in Müller and retinal ganglion cells. These results suggest that increase in TRPC1/5 heteromers may contribute to slowing of the degeneration of the inner retina during the outer retinal degeneration.

The emergence of prosumers, who actively participate in designing and producing goods, has generated interest in domestically manufactured products. Factors such as innovation, design methods, component reuse, prototyping, and digital fabrication empower prosumer designers to realize their ideas and enhance products to meet their specific design requirements. This article presents a case that combines bioinspired design methods with prosumer characteristics from the perspective of a designer who uses biological research results acting as a prosumer. By analyzing prosumer needs, bioinspired design, and domestic fabrication requirements, designers define the methods that best suit their possibilities. As a result of using biological information, the geometry of Samara seeds, propeller sizing, wind tunnel tests, and subsequent improvements, the custom design of a bioinspired microgenerator has been refined to the final design of a bicycle flashlight. The aim is to popularize a working approach that facilitates the interaction of design methods and reinforces domestic manufacturing processes. Implementing bioinspired design methods within the prosumer context offers a methodological alternative to transform the current economic model, promoting systemic sustainability and the development of proprietary technologies.

The aim of this work was to classify the business incubators in Spain according to the four phases of the startup’s incubation process. Considering that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the business incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis has been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors. Finally, the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3, named activity monitoring and control, was related to phase 3 or basic incubation variables. Cluster analysis facilitates the grouping of business incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small sized business incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factors 1 and 2. Factor 3, although positive, it is susceptible to improvement. They are the largest group of business incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

As consequence of COVID-19, millions of households suffered mobility restrictions and changes in their lifestyle during several months. The aim of this study was to evaluate the effects of COVID-19 home confinement in food habits, lifestyle and emotional balance of the Spanish population. This cross-sectional study used data collected via an anonymous online questionnaire during the last month before lockdown finished in Spain in a total of 675 participants. 38.8% of the respondents experienced weight gain while 31.1% lost weight during confinement. The increase in body weight was positively correlated with the age (Rs = 0.14, p &lt;0.05) and BMI (Rs = 0.20, p &lt;0.05). We also identified that 39.7% reported poorer quality sleep, it was positively correlated with BMI (Rs = -0.18, p &lt;0.05) and with age (Rs = -0.21, p &lt;0.05). 44.7% of the participants had not performed physical exercise during confinement with differences by sex (p &lt;0.05), by age (p &lt;0.05), by BMI (p &lt;0.05) and sleep quality (p &lt;0.05). According to emotional-eater questionnaire, 21.8% and 11% were classified as emotional eater and very emotional eater, respectively. We emphasize the importance of adopting a healthy lifestyle, as the COVID-19 pandemic nowadays is ongoing.

To reduce environmental impacts from sodium silicate synthesis it was suggested the use of sugarcane bagasse ash (SCBA) as a source of silicon dioxide and sodium carbonate using the ceramic method. Although the production of sodium silicate is carried out on a large scale, it should be noted that its process requires temperatures above 1000 °C or the use of highly corrosive agents such as sodium hydroxide and chlorine gas used to neutralize the remaining sodium hydroxide. In the present work, the synthesis temperatures were reduced to 800 °C with a reaction time of 3 hours by pressing equimolar mixtures of previously purified SCBA and sodium carbonate, then heat treatment was carried out under the indicated conditions. The resulting materials were analyzed by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD). Among the crystalline phases, calcium disodium silicate was identified, in addition to sodium silicate, so it was inferred that the other components of the ash can interfere with the synthesis of silicate. Therefore, to obtain the highest composition of sodium silicate, a leaching treatment of the SCBA is required.

During the COVID-19 pandemic, the high prevalence of comorbidities in Mexico, as well as the disparities between public and private health subsystems, substantially contributed to the severe impact it had in the country. The objective of this study was to evaluate and compare risk factors present at admission for mortality of hospitalized patients with COVID-19. A 2-year retrospective cohort study of hospitalized adult patients with COVID-19 was conducted at a private tertiary care center. The study population consisted of 1,258 patients with a median age of 56 ± 16.5 years, of whom 1,093 recovered (86.8%) and 165 died (13.1%). In the univariate analysis, older age (p &lt;0.001), comorbidities such as hypertension (p &lt;0.001) and diabetes (p &lt;0.001), signs and symptoms of respiratory distress, and markers of acute inflammatory response were significantly more frequent in non-survivors. The multivariate analysis showed that older age (p &lt;0.001), the presence of cyanosis (p 0.005) and previous myocardial infarction (p 0.032) were independent predictors for mortality. In the studied cohort, risk factors present at admission associated with an increased risk of death were older age, cyanosis and a previous myocardial infarction, which can be used as valuable predictors for patients’ outcomes. To our knowledge, this is the first study analyzing predictors of mortality in COVID-19 patients attended on a private tertiary hospital in Mexico.

Anti-Müllerian hormone (AMH) has been proposed as biomarker for fertility in cattle, yet this associative relationship appears to be influenced by heat stress. Objective was to test serum AMH and AMH-related single nucleotide polymorphisms (SNPs) as markers potentially predictive of reproductive traits in heat-stressed dairy cows. The study included 300 Holstein cows that were genotyped using BovineSNP50 (54,000 SNP) after blood samples were collected and DNA extracted. A genome wide association study was then executed. Nine intragenic SNPs within the pathways that influence the AMH gene were found important with multiple comparisons adjustment test (p&lt;1.09x10-6). A further validation study was performed in an independent Holstein cattle population, which was divided into moderate (MH; n=152) and severe heat-stressed (SH; n=128) groups, and subjected to a summer reproductive management program. Serum AMH was confirmed as a predictor of fertility measures (p&lt;0.05) in MH but not in SH group. Cows were genotyped using the TaqMan allelic discrimination method and qPCR, which revealed four SNPs as predictive markers for serum AMH (p&lt;0.01), reproductive traits (p&lt;0.01) and physiological variables (p&lt;0.05). These SNPs were in the genes AMH, IGFBP1, LGR5 and TLR4. In conclusion, both serum AMH concentrations and AMH-related SNPs appear to be associated with fertility traits in dairy cows managed during summer.

Pinus patula is one of the most planted wood conifer species worldwide; however, no foliar nutrient standards exist for this species up to date. The objective of the present study was to generate and verify two sets of foliar nutrient standards for nearly ten-year-old P. patula trees: critical nutrient concentrations and DRIS norms. Nutrients studied were N, P, K, Ca, Mg, Fe, Cu, Zn, Mn, and B. The reference standards were verified experimentally by installing two fertilization trials; one of them located in Huayacocotla, state of Veracruz and the other one in Aquixtla, state of Puebla, Mexico. Nutrient status of each fertilization trial was correctly predicted by critical nutrient values and DRIS as well. Both standards were able to detect the secondary growth-limiting nutrient deficiency in the Huayacocotla trial, where the primary limitation for growth was scarcity of solar radiation within tree crowns. The limiting nutrient in both experimental trials was K.

Bimetallic nanoparticles are of interest since they lead to many interesting electrical, chemical, catalytic, and optical properties. They are particularly important in the field of catalysis since they show superior catalytic properties than their monometallic counterparts. The structures of bimetallic nanoparticles depend mainly on the synthesis conditions and the miscibility of the two components. In this work, PdPt alloyed-bimetallic nanoparticles (NPs) were synthesized through the polyol method, and characterized using spherical aberration (Cs) corrected scanning transmission electron microscopy (STEM). High-angle annular dark-field (HAADF)-STEM images of bimetallic nanoparticles were obtained. The contrast of images shows that nanoparticles have an alloy structure with an average size of 8.2 nm. Together with the characterization of nanoparticles, a systematic molecular dynamics simulations study, focused on the structural stability and atomic surface segregation trends in 923-atom PdPt alloyed-bimetallic NPs was carried out.

Obesity has increasingly become a worldwide epidemic, as demonstrated by epidemiological and clinical studies. Obesity may lead to development of a broad spectrum of cardiovascular diseases (CVDs), such as coronary heart disease (CHD), hypertension, heart failure (HF), cerebrovascular disease, atrial fibrillation (AF), ventricular arrhythmias, and sudden cardiac death (SCD). In addition to hypertension, there are other cardiometabolic risk factors (CRFs) such as visceral adiposity, dyslipidemia, insulin resistance, diabetes, elevated levels of fibrinogen, and C-reactive protein and others, all of which increase the risk of CVD events. Mechanisms involved between obesity and CVD mainly include insulin resistance, oxidative stress, inflammation, and adipokines dysregulation, which cause maladaptive structural and functional alterations of the heart, particularly left ventricular (LV) remodeling and diastolic dysfunction. Natural products of plants, provide a diversity of nutrients and different bioactive compounds, including phenolics, flavonoids, terpenoids, carotenoids, anthocyanins, vitamins, minerals, fibers, and others, which possess a wide range of biological activities including antihypertensive, antilipidemic, antidiabetic, and other activities, thus conferring cardiometabolic benefits. In this review, we discussed the main therapeutic interventions using extracts from herbs and plants in preclinical and clinical trials with protective properties targeting CRFs. Molecular mechanisms and therapeutic targets of herbs and plants extracts for the prevention and treatment of CRFs are also reviewed.

There is an urgent need to develop new therapies for cancer treatment due to high rates of resistance and tumor relapse. Moreover, chemotherapy and radiation weaken the immune system and leave patients susceptible to sudden death from infections and organ failure since antineoplastic drugs lack specificity. Hence, scientists worldwide continue the search for natural alternatives with anticancer activities and fewer side effects. In this regard, traditional medicine offers strategies for preventing and treating numerous diseases and nowadays scientific studies worldwide highlight some of the mechanisms underlying their potential as an effective alternative for the management of cancer. In Mexico, Mayan healers have been prescribed mainly medicinal plants for more than 2,000 years. Furthermore, their ethnomedical knowledge has led to drug discovery or the development of herbal remedies. Medicinal plants from the genus of Cissus remain an important element of all indigenous medical systems in Mexico including the Mayan tribes in Yucatan, particularly for the management of gastrointestinal illnesses, sores, cutaneous diseases, and tumors. In this review, we present the reported bioactivities against cancer cells of the extract and compounds from the species of Cissus with a particular focus on recent studies on the phytochemistry of C. trifoliata which is widely distributed in Mexican territory and used for tumor management in traditional medicine.

The kynurenine pathway (KP) and the endocannabinoid system (ECS) are known to be deregulated in depression and obesity; however, it has been recognized that acute physical exercise has an important modulating role inducing changes in the mobilization of their respective metabolites -endocannabinoids (eCB) and kynurenines (KYN)- which overlap at some points, acting as im-portant antidepressant, anti-nociceptive, anti-inflammatory, and antioxidant biomarkers. There-fore, the aim of this review is to analyze and discuss some studies performed recently to investigate the potential interactions between both systems, particularly, those related with exercise-derived endocannabinoidome and kynurenine mechanisms and to elucidate how, the prescription of physical exercise could represent a new approach for the clinical manage of these two conditions.

BACKGROUND Detecting total cholesterol in dried blood spots could aid in identifying individuals with a high likelihood of familial hypercholesterolemia and could be used as a screening measure. This study aims to assess the diagnostic accuracy of dried blood spots on Whatman 903 paper cards using a manual enzymatic technique. METHODS A total of 394 samples collected as serum and dried blood spots were compared. Cholesterol was determined in serum using the automated reference method, while cholesterol on paper was measured using a manual enzymatic method. Within- and between-day diagnostic variability were analyzed. The correlation between both methods was assessed using Passing-Bablok regression and Bland-Altman plot. Internal validation of our correlation formula was performed on 149 samples, along with external validation of the formula proposed by Corso et al. RESULTS The within- and between-day coefficient of variation was found to be lower than 10.14% and 14.09%, respectively. Method comparison yielded an area under the curve of 0.976, with a standard error of 0.009. Passing-Bablok regression indicated a precision of 0.803 and an accuracy of 0.96. Internal validation precision was measured at 0.716. Regarding internal validation, calculated cholesterol with our regression line did not differ from serum cholesterol analysis, while significant differences were observed in calculated cholesterol levels using the external formula. CONCLUSIONS Total cholesterol analysis in dot blood spots demonstrates high precision and reproducibility. This method reliably enables the incorporation of this biological marker into neonatal screening for familial hypercholesterolemia detection.

The changes in consumer preferences and the increasingly competitive global market have demanded that food entrepreneurs engage in innovative value-added activities. The date is a delicatessen fruit known by its content of active compounds (e.g., dietary fiber and antioxidants) and its biological activity which has a vast potential in the design of new products such as bioactive ingredients, sugar substitutes, dietary supplements, functional foods, among others. In the current paper, innovative approaches to the value addition to date fruits and their processing by-products have been reviewed from recent high-quality scientific works. New processes such as ultrafiltration and hydrothermal treatments are shown as a useful alternative to obtain differentiated date-based ingredients (e.g., fiber concentrates, sap syrups, and date powders). Moreover, the use of date fruits and their byproducts as natural sources of value-added active compounds in the preparation of dairy, meat, and bakery and cereal products is also presented.

The tourism sector in general and the hotelier in particular face the challenge of managing appropriate measures to deal with the covid-19 pandemic. In this sense it is useful to know what the measures are most demanded by the clientele. This research, by analyzing the variance (ANOVA) of a factor concluded that women are more demanding than men in terms of the level of demand in relation to the measures to be taken in hotels. This, as a practical application, allows to know more accurately the expectations, demands and demands of the client segmented by sex, in order to satisfy and improve the tourist experiences.

The tourism sector in general and the hotelier in particular face the challenge of managing appropriate measures to deal with the covid-19 pandemic. In this sense it is useful to know what the measures are most demanded by the clientele. This research, by analyzing the variance (ANOVA) of a factor concluded that women are more demanding than men in terms of the level of demand in relation to the measures to be taken in hotels. This, as a practical application, allows to know more accurately the expectations, demands and demands of the client segmented by sex, in order to satisfy and improve the tourist experiences.

The tourism sector in general and the hotelier in particular face the challenge of managing appropriate measures to deal with the covid-19 pandemic. In this sense it is useful to know what the measures are most demanded by the clientele. This research, by analyzing the variance (ANOVA) of a factor concluded that women are more demanding than men in terms of the level of demand in relation to the measures to be taken in hotels. This, as a practical application, allows to know more accurately the expectations, demands and demands of the client segmented by sex, in order to satisfy and improve the tourist experiences.

Human Parechoviruses, officially known as Parechovirus A (PeV-A), is associated with mild gastrointestinal and respiratory illness in young children, however, they may also give rise to Central Nervous System (CNS) infections and neonatal sepsis. While studies have delved into the detection of PeV-A in different populations, the detection of PeV-A in Hispanic populations in Latin American countries is not well-known. The aim of this study was to determine the presence of PeV-A in respiratory, gastrointestinal, and neurological clinical samples of pediatric patients in Panama. Two hundred samples of pediatric patients with a negative diagnosis for the main respiratory viruses, rotavirus and neurological viruses such as herpesvirus, enterovirus and cytomegalovirus, collected between 2014 and 2015, were analyzed by real-time RT-PCR. Eight positive PeV-A infections were detected, 2 in respiratory samples, 5 in stool samples and one detected in cerebrospinal fluid. This is the fisrt report of PeV-A in Panamá.

Today, it is difficult to have a high-field nuclear magnetic resonance device (NMR) due to the high cost of its acquisition and maintenance. These high-end machines require significant space and specialist personnel for operation and offer exceptional quality in the acquisition, processing, and other advanced functions associated with detected signals. However, alternative devices are low-field nuclear magnetic resonance devices. They benefit from the elimination of high-tech components that generate static magnetic fields and advanced instruments. Instead, they used magnetic fields induced by ordinary conductors. Another category of spectrometers uses the Earth's magnetic field, which is simple and economical, but limited in use. These devices are called Earth Field Nuclear Magnetic Resonance (EFNMR). This device is ideal for educational purposes, especially for engineers and those who study nuclear magnetic resonance, such as chemistry or other experimental sciences. Students can observe their internal workings and conduct experiments that complement their education without worrying about damaging equipment. This article provides a detailed explanation of the design and construction of electrical technology devices for the excitation of atomic spin resonance using Earth's magnetic fields. Covers all necessary stages, from research to analysis, from simulation, assembly, construction of each component, and the development of comprehensive software for spectrometer control.

This paper shows the development of a simultaneous tri-band (S: 2.2 - 2.7 GHz, X: 7.5 - 9 GHz and Ka: 28 - 33 GHz) low-noise cryogenic receiver for geodetic Very Long Baseline Interferometry (geo-VLBI) which has been developed by the technical staff of Yebes Observatory (IGN) laboratories in Spain. The receiver was installed in the first radio telescope of the Red Atlántica de Estaciones Geodinámicas y Espaciales (RAEGE) project, which is located in Yebes Observatory, in the frame of the VLBI Global Observing System (VGOS). After this, the receiver was borrowed by the Norwegian Mapping Autorithy (NMA) for the commissioning of two VGOS radiotelescopes in Svalbard (Norway). A second identical receiver was built for the Ishioka VGOS station of the Geospatial Information Authority (GSI) of Japan, and a third one for the second RAEGE VGOS station, located in Santa María (Açores Archipelago, Portugal). The average receiver noise temperatures are 21, 23 and 25 Kelvin and the measured antenna efficiencies are 70%, 75% and 60% in S-band, X-band and Ka-band, respectively.

This article focuses on generating an alternative in order to identify traffic officers during driving. This research employed the latest You Only Look Once (YOLO) model, using a six-phase methodology: data collection, data preparation involving resizing and labeling, implementation of various filters to avoid overfitting, model training, prediction evaluation, and result interpretation. The YOLO model was applied across three iterations using a dataset of 1862 images. To enhance training efficiency and detection speed, the graphics processing unit (GPU) acceleration was utilized, further enhancing the experimental process. The results of this study revealed that the YOLOv8x variant produced the most promising results. This proposed model attained a remarkable F1 score of 0.95, bolstered by a confidence score of 0.631, with the potential for an increase to 0.80 in confidence without significantly compromising the F1-score. These findings are poised to make a substantial contribution to the broader research landscape, particularly in advancing the effectiveness of detection models for traffic officers.

In computer vision, human action recognition is a hot topic, popularized by the development of deep learning. Current models have achieved high accuracy results on public datasets. Despite this success, they require significant computational resources for training. Given that transfer learning based techniques allow reusing what other models have already learned and training models with less computational resources, in this work we propose using a transfer learning based approach for action recognition in videos. We describe a methodology for human action recognition using transfer learning techniques in a custom dataset. The proposed method consists of four stages: 1) human detection and tracking, 2) video preprocessing, 3) feature extraction (using pretrained models with ImageNet), and 4) action recognition using a two-stream model consisting of TCNs, LSTMs, and CNNs layers. The custom dataset is imbalanced with 189, 390, 490, 854, and 890 videos per class, respectively. For feature extraction, we analyzed the performance of seven pretrained models: Inception-v3, MobileNet-v2, MobileNet-v3-L, VGG-16, VGG-19, Xception, and ConvNeXt-L. We show that the best results were obtained with the last one. Finally, using pretrained models for feature extraction allowed training in a PC with a single GPU with an accuracy of 94.9%.

This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.

The purpose of this study is to analyse the feasibility of using waste from granite gang saws (GCW-GS) to manufacture ultra-high performance, steel-fibre reinforced concrete (UHPFRC). These machines cut granite blocks by abrasion using a steel blade and slurry containing fine steel grit. The waste generated by gang saws (GCW-GS) contains up to 15% Fe2O3 and up to 5% CaO. This is the main difference from the waste produced by diamond saws (GCW-D). Consequently, the second objective of this study is to compare the results of the waste obtained with gang saws with that from diamond saws, in order to determine the influence of iron and calcium oxides. The waste from cutting granite with gang saws was used in different percentages to replace micronized quartz powder of natural origin in the manufacture of UHPRFC. All the test specimens were analysed to determine their compressive strength, elasticity modulus, flexural strength and indirect tensile strength. The final conclusion is that wastes from both gang saws and diamond saws can be used to manufacture UHPFRC with an improvement in the mechanical properties up to a 35% replacement. The results for GCW-GS are better, mainly due to the pozzolanic effect of the iron dioxide. For higher percentage replacements the mechanical properties are close to the control concrete with small decreases.

Biopolymers based on plant and animal proteins are interesting alternatives in the development of films with future prospects as food packaging. Considering that in recent years there has been an increasing interest in the valorization of agro-industrial residues and by-products and that the blending of polymers can lead to materials with improved properties, in this work, keratin-rich feather fibers and gliadins were blended at different ratios in order to develop sustainable and biodegradable films. Control gliadin G100, feather F100 films and their blends at 3:1 (G75F25) , 2:2 (G50F50) and 1:3 (G25F75) ratios were successfully developed through thermoprocessing. The physical properties were differentiated as a function of the concentration of both polymeric matrices. Although gliadins showed higher hydrophilicity confirmed by its highest swelling degree, films with high gliadin ratios exhibited lower water permeability values at low and medium relative humidities. On the other hand, the feathers displayed the highest Young´s modulus values and provided oxygen barrier to the blends, principally at the highest relative humidity. In conclusion, the blend of these protein-based polymers at different ratio resulted on interesting composites whose physical properties could be adjusted.

Technology has transformed aeroponics, providing numerous advantages over traditional soil-based agriculture. However, there remains a need for comprehensive information on the types of technology employed in aeroponics and their impact on the growing process. This paper presents a literature review of 47 studies published between 2012 and 2023 in peer-reviewed journals and conference proceedings. As a result, it identifies the status and tendencies in the usage of technology in aeroponics as well as the main opportunities and challenges. Furthermore, this paper introduces the Technology Adoption and Integration in Sustainable Agriculture (TAISA) model. TAISA is a model that identifies the degree of technology integration in any sustainable agriculture system to determine how technology affects production and quality. Overall, the systematic review suggests that technology can play a vital role in improving the efficiency and sustainability of aeroponic farming. However, careful consideration must be given to the costs and technical requirements associated with using these technologies. Moreover, the TAISA model reveals that technology has primarily been employed in creating new processes that are not possible to implement without the help of technology. Therefore, we conclude that technology use has taken root in aeroponics and can be promoted to improve sustainable agriculture.

Background: Although confirmed cases of infection with severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) have been declining since late 2020 due to general vaccination, little research has been done regarding the impact of vaccines against SARS-CoV-2 in Spain in terms of hospitalizations and deaths. Objective: Our aim was to identify the reduction in severity and mortality of coronavirus disease 2019 (COVID-19) at a nationwide level due to vaccination. Methods: We designed a retrospective, population-based study to define waves of infection and to describe the characteristics of the hospitalized population. We also studied the rollout of vaccination and its relationship with the decline in hospitalizations and deaths. Finally, we developed two mathematical models to estimate non-vaccination scenarios using machine learning modeling (with the ElasticNet and RandomForest algorithms). The vaccination and non-vaccination scenarios were eventually compared to estimate the number of averted hospitalizations and deaths. Results: In total, 498,789 patients were included, with a global mortality of 14.3%. We identified six waves or epidemic outbreaks during the observed period. We established a strong relationship between the beginning of vaccination and the decline in both hospitalizations and deaths due to COVID-19 in all age groups. We also estimated that vaccination prevented 170,959 hospitalizations (CI 95% 77,844–264,075) and 24,546 deaths (CI 95% 2,548–46,543) in Spain between March 2021 and December 2021. We estimated a global reduction of 9.19% in total deaths during the first year of COVID-19 vaccination. Conclusions: Demographic and clinical profiles changed over the first months of the pandemic. Patients over 80 years old and other age groups obtained clinical benefit from early vaccination. The severity of COVID-19, in terms of hospitalizations and deaths, decreased due to vaccination.

The diagnosis and treatment of autoimmune diseases are major challenges. Their signs, symptoms, and their clinical severity change throughout the course of the disease. The available treatments for these conditions do not result in complete remission, and their long-term use generates several side effects. The main challenges in this field are the development of more sensitive diagnostic tools, and effective treatments. Studies in patients and animal models reported alterations in monocyte phenotype, activation, and function. These cells play an essential role in the pathogenesis of chronic inflammatory states and have become a target for extracorporeal monitoring and specific intervention. Nanoparticles (NPs) are ultrafine particles that can be used as contrast agents in diagnostic imaging techniques to detect specific cells in inflammatory infiltrates in tissues that are not easily accessible by biopsy. In addition, NPs can be designed to deliver drugs to a cell population or tissue. This review describes several experimental pieces of evidence demonstrating that monocytes and macrophages can specifically uptake various types of NPs, thus becoming detectable in vivo by magnetic resonance imaging and susceptible to be modulated by therapeutic agents. Hence, nanoparticles targeting mononuclear phagocytes represent promising tools for diagnosing and treatment.

The use of probiotics in reproductive-related dysbiosis is an area of continuous progress due to the growing interest from clinicians and patients suffering recurrent reproductive microbiota disorders. An imbalance in the natural colonization sites related to reproductive health: vaginal, cervicovaginal, endometrial and also pregnancy-related altered microbiota could play decisive role in reproductive outcomes. Oral and vaginal administrations are in continuous discussion regarding the clinical effect pursued, but probiotics as oral supplement therapy is the route administration better studied. To complement and summarise with qualitative and quantitative information of vaginal probiotics clinical studies, the main objective of this work was to retrieve the standardised protocols commonly used and their microbiota modulation capacities. The studies selected were related to treat bacterial vaginosis (BV) as the most commonly disorder, few studies on vulvovaginal candidiasis (VVC) and also administration to stabilise microbiota before in vitro fertilisation (IVF). Probiotic doses administered were similar to oral probiotics protocols, ranging from ≥ 107 CFU/day to 2.5 x 1010 CFU/day, and variable regarding posology duration from 1 day to 12 weeks, being 1 week commonly applied. Moderate modulation was achieved regarding the relative abundance decrease of abnormal microbiota, coinciding with parallel increase in Lactobacillus species.

The intracellular calcium concentration ([Ca2+]i) modulation plays a key role in the regulation of cellular growth and survival in normal cells and failure of [Ca2+]i homeostasis is involved in tumor initiation and progression. Here we show that inhibition of Furin by its naturally occurring inhibitor the prodomain ppFurin in the MDA-MB-231 breast cancer cells resulted in enhanced SOCE through TRPC6 activation that associated reduced cells malignant phenotype. Expression of ppFurin in a stable manner in MDA-MB-231 and the melanoma MDA-MB-435 cell lines inhibits Furin activity as assessed by in vitro digestion assays. Accordingly, cell transfection experiments, revealed that the ppFurin-expressing cells are unable to process adequately the PC substrates proVEGF-C and proIGF-1R. Compared to MDA-MB-435 cells, expression of ppFurin in MDA-MB-231 significantly induces Ca2+ entry which is impaired by silencing of TRPC6 expression. Analysis of TRPC6 activation revealed its up-regulated tyrosine phosphorylation in ppFurin-expressing MDA-MB-231 cells. The expression of ppFurin in MDA-MB-231 cells reduced their viability and ability to migrate and enhanced their sensitization to the apoptosis inducer hydrogen peroxide. These findings suggest that Furin inhibition by ppFurin may be a useful strategy to interfere with Ca2+ mobilization leading to breast cancer cells malignant phenotype repression and reduction of their resistance to treatments.

Beta-lactam resistant bacteria, commonly resident in tertiary hospitals, have emerged as a worldwide health problem because of ready-to-eat vegetable intake. We aimed to characterize the genes providing resistance to beta-lactam antibiotics in Enterobacteriaceae, isolated from five commercial salad brands for human consumption in Mexico City. 25 samples were collected, grow in blood agar plates, the bacteria were biochemistry identified and antimicrobial susceptibility testing was done, the carried family genes were identified by endpoint PCR and the specific genes were confirmed with WGS by NGS. 12 positive cultures were identified and their microbiological distribution was as follows, 8.3% for Enterobacter aerogene (n=1), 8.3% for Serratia fonricola (n=1), 16.7% for Serratia marcesens (n=2), 16.7% for Klebsiella pneumoniae (n=2), and 50% (n=6) for Enterobacter cloacae. The endpoint PCR results showed 11 colonies positive for blaBIL (91.7%), 11 for blaSHV (91.7%), 11 for blaCTX (97.7%), 12 for blaDHA (100%),4 for blaVIM (33.3%), 2 for blaOXA (16.7%), 2 for blaIMP (16.7%), 1 for blaKPC (8.3%) and 1 for blaTEM (8.3%) gene, all samples were negative blaROB, blaCMY, blaP, blaCFX and blaLAP gene. The sequencing analysis revels a specific genotypes for Enterobacter cloacae (blaSHV-12, blaCTX-M-15, blaDHA-1, blaKPC-2); Serratia marcescens (blaSHV-1, blaCTX-M-3, blaDHA-1, blaVIM-2); Klebsiella pneumoniae (blaSHV-12, blaCTX-M-15, blaDHA-1); Serratia fonticola (blaSHV-12, blaVIM-1, blaDHA-1) and Enterobacter aerogene (blaSHV-1, blaCTX-M-1, blaDHA-1, blaVIM-2, blaOXA-9). Our results indicate that beta-lactam resistant bacteria have acquired integrons with a different number of genes that providing panresistance to beta-lactam antibiotics, including penicillins, oxacillins, cefalosporins, monobactams, carbapenems and imipenems.

Artificial Intelligence (AI) has emerged as a disruptive technology in various areas, and medicine is no exception. In the last decade, there has been rapid progress in the application of AI in healthcare, from diagnosing and prognosticating diseases to improving operational efficiency in hospitals. This literature review explores the advances of artificial intelligence in the field of medicine, discusses its benefits, and discusses the ethical and regulatory challenges that need to be addressed to maximize its potential.

Introduction: The exponential growth of the SARS-CoV-2 virus transmission during the first months of 2020 has placed substantial pressure on health systems worldwide. The complications derived from the novel coronavirus disease (COVID-19) vary in due to comorbidities, sex and age, with more than 50% of the patients who require some level of intensive care developing acute respiratory distress syndrome (ARDS). Areas covered: Various complications caused by SARS-CoV-2 infection have been identified, the most lethal being the acute respiratory distress syndrome, caused most likely by the presence of severe immune cell response and the concomitant alveolus inflammation. The authors carried out an extensive and comprehensive literature review on SARS-CoV-2 infection, the clinical, pathological and radiological presentation as well as the current treatment strategies. Expert Opinion Elevation of inflammatory biomarkers is a common trend among seriously ill patients. The information available strongly suggests that in COVID-19 patients, their altered immune response, including a massive cytokine storm, is responsible for the further damage evidenced among ARDS patients. The increasingly high number of scientific articles and evidence available can only suggest that the individualization of each case is the norm, not all patients with acute respiratory failure due to COVID-19 meet the Berlin definition and therefore ARDS should be considered as a heterogeneous disease, with a wide range in the expression of its severity and clinical manifestations.

Polycystic ovary syndrome (PCOS) usually comes along with metabolic disturbances attributed to androgen excess and obesity, but the contribution of each has not been defined, and the occurrence of metabolic disturbances is frequently not investigated. We evaluated 99 PCOS and 41 non-PCOS women. Clinical biomarkers of glucose-, liver-, and endothelial-related metabolic alterations were measured; participants were categorized into four groups according with obesity (OB) and hyperandrogenemia (HA) statuses: Healthy (no-HA, lean), HA (HA, lean), OB (no-HA, OB), and HAOB (HA, OB). Metabolic disturbances were highly frequent in PCOS women (70%). BMI correlated with all biomarkers, while free testosterone (FT) only with glucose- and hepatic-related indicators. Despite insulin sensitivity and liver enzymes were associated with FT, women with obesity exhibited lower M [coeff = 8.56 – 0.080(FT) –3.71(Ob); p &lt;0.001)] and higher aspartate aminotransferase (coeff = 26.27 + 0.532(FT) + 8.08(Ob); p = 0.015)] than lean at the same level of FT. Women with obesity exhibited greater risk of metabolic disorders than lean, independently of hyperandrogenemia. Clinicians are compelled to search for metabolic alterations in PCOS women; obesity must be handled in all cases, but hyperandrogenemia needs to be managed also in those with glucose- or liver-related disturbances.

Industry 4.0 is an industrial paradigm that is causing changes in form and substance in factories, companies and businesses around the world, and is impacting work and education in general. In fact, the disruptive technologies that frame the fourth industrial revolution have the potential to improve and optimize manufacturing processes and the entire value chain, which can lead to an exponential evolution in the production and distribution of goods and services. All these changes imply that the fields of engineering knowledge must be oriented towards the concept of Industry 4.0, for example Mechanical Engineering. The development of various physical assets that are used by cyber-physical systems and digital twins is based on Mechanics. However, the specialized literature on Industry 4.0 says little about the importance of Mechanics in the new industrial era and more importance is given to the evolution of Information and Communication Technologies and Artificial Intelligence. This article presents a frame of reference about the importance of Mechanical Engineering in Industry 4.0 and proposes an extension to the concept of Mechanics 4.0, recently defined as the relationship between Mechanics and Artificial Intelligence. For the analysis of Mechanical Engineering in Industry 4.0, the criteria of the four driving forces that defined Mechanics in the third industrial revolution was used. An analysis of Mechanical Engineering Education in Industry 4.0 is presented, and the concept of Mechanical Engineering 4.0 Education is improved. Finally, the importance of making changes in the educational models of engineering education is described.

This preprint is focused in the presence of plastics and microplastics in food. We will discuss how many we eat, and how they arrive to the food, and why. We will treat many other things, such as the waste treatment in Europe and in Spain, with updated data; how much plastic waste is generated; what are microplastics and how they are analyzed, I will tell about the experience we have at the University of Alicante (UA); how they can be removed and we will estimate how many we eat over the course of a year.

By analyzing the urban landscape, this investigation focuses on commercial typologies in historical urban areas and its relationship with the urban landscape and its heritage values. Trade plays an essential role in historical urban areas, both in the past and in the present, since it is part of the urban landscape—creating it and modifying it, but also preserving it. Historical protected urban areas contain diverse elements reflecting the impacts of commercial activities that have existed in cities throughout history. At present, the urban landscape of commercial activity is made up of a multiplicity of typologies and formats which interact with the historical landscape and its values, using them to strengthen its strategies of attraction, differentiation, and sales. Shop owners contribute to the preservation of historic urban areas by maintaining the commercial functions within them. Therefore, we affirm that the role of commercial activity in the preservation of urban protected areas is essential. However, further research is needed because this aspect has not been addressed in depth by the scientific community specializing in the management of cultural heritage.

Dengue is one the most significant mosquito-borne viral diseases globally, with its prevalence extending across tropical and subtropical regions, exerting a considerable financial strain on health systems. Despite decades of research leading to the development of a vaccine implemented in endemic countries, its usage remains restricted to a fraction of the population at risk of contracting dengue. Due to these limitations, there is a growing focus on research aimed at unraveling the cellular mechanisms crucial for Dengue virus (DENV) infection to pinpoint potential host targets. Multiple studies propose a pivotal role of cytoskeletal remodeling in DENV infection. Specifically, DENV alters the organization of actin to facilitate viral entry, replication, and release. In this study, we investigated the involvement of the protein c-Abl, a kinase crucial in actin dynamics, in the context of DENV infection. Our findings suggest that either silencing or pharmacological inhibition of the kinase c-Abl leads to accumulation of dengue ENV protein in vitro, associated with actin remodeling. These results illuminate cellular mechanisms that could serve as potential therapeutic alternatives for dengue management.

Autism Spectrum disorder (ASD) and intellectual disability (ID) are the most frequent develop-mental disorders with a prevalence between 3% and 5% of the population. In addition, both ASD and ID can be found in the same patient. Mutations in several genes involved in the epigenetic regulation of gene expression have been linked to different ID associated with ASD features including alterations of the ly-sine-acetyltransferase 6A (KAT6A) gene in KAT6A syndrome. KAT6A enzyme participates in a wide range of critical cellular functions such as chromatin remodeling, gene expression, protein synthesis, cell metabolism, and replication. In this manuscript, we examined the pathophysiolog-ical alterations in fibroblasts derived from three patients harboring KAT6A mutations. We ad-dressed survival in stress medium, histone acetylation, protein expression patterns and tran-scriptome analysis as well as cell bioenergetics. In addition, we evaluated the therapeutic effec-tiveness of epigenetic modulators and mitochondrial boosting agents such as pantothenate and L-carnitine in correcting the mutant phenotype. Pantothenate and L-carnitine treatment increased histone acetylation and corrected protein and transcriptomic expression patterns in mutant KAT6A cells. Furthermore, cell bioenergetics of mutant cells was significantly improved. Our results suggest that pantothenate and L-carnitine can significantly correct the mutant phe-notype in cellular models of KAT6A syndrome.

Background: The effectiveness of the anti-COVID-19 vaccine remains a matter to be clarified. Methods: The humoral and cellular immunity after the administration of three doses of the Pfizer–BioNTech and Oxford AstraZeneca vaccines against SARS-CoV-2 over one year and the appearance of post-vaccination COVID-19 have been studied. Results: Anti-SARS-CoV-2 IgG and IgA antibodies showed a progressive increase throughout the vaccination period. This increase was greatest after the third dose. The highest levels were observed in subjects who had anti-SARS-CoV-2 antibodies prior to vaccination. There was an increase in CD4+ αβ, CD8+ γδ and TEM CD8+ γδ T cells, and a decrease in apoptosis in CD4+CD8+ and CD56+ αβ and γδ T cells. Post-vaccination SARS-CoV-2 infection was greater than 60%. The symptoms of COVID-19 were very mild and were related to γδ T cell deficit, specifically CD8+ TEMRA and CD56+ γδ TEM, as well as lower pre-vaccine apoptosis levels. Conclusions: Those results demonstrate the important role that γδ T cells play in SARS-CoV-2 vaccine immunization.

The nutritional composition of food for animal production can be completed using olive tree and plant by-products due to their high contents of bioactive compounds, such as pentacyclic triterpenes. Here, we present a novel application of near-infrared spectroscopy (NIRS) for the prediction of the total or individual [maslinic acid (MA), oleanolic acid (OA), and uvaol (UO)] pentacyclic triterpene concentrations in a feed additive obtained from a plant mixture. The oxygen radical absorbance capacity of these types of samples demonstrated the existence of a high antioxidant capacity. The conventional determination methods of pentacyclic triterpenes concentration are costly, labor-intensive, and not practical for analyzing several lines within a limited timeframe at the factory level. The optimal regression model developed in our work demonstrated high correlation values for the calibration and validation sets, along with a high residual prediction deviation value. The NIRS method can be applied directly to dried powder and avoids extraction and high-performance liquid chromatography (HPLC) analysis. Our results also demonstrate that NIRS can accurately quantify pentacyclic triterpenes even at low concentrations in food additives. It can be used at the factory level to directly determine the concentrations in the additive powder obtained at the same time that the powder is produced.

Unidentified abortion, of which leptospirosis, brucellosis and ovine enzootic abortion are important factors, is the main cause of disease spread between animals and humans in all agricultural systems in most developing countries. Although there are well-defined risk factors for these diseases, these characteristics do not represent the prevalence of the disease in different regions. This study predicts the unidentified abortion burden from multi-microorganisms in ewes based on artificial neural networks approach and GLM. Methods: A two-stage cluster survey design was conducted to estimate the seroprevalence of abortifacient microorganisms, and to identify putative factors of infectious abortion. Results: Overall seroprevalence of Brucella was 70.7%, while Leptospira spp. was 55.2%, C. abortus 21.9% and B. ovis 7.4%. Serological detection with the 4 abortion-causing microorganisms was determined only in 0.87% of sheep sampled. The best GLM is integrated by serological detection of serovar Hardjo and Brucella ovis in animals of the slopes with elevation between 2600 to 2800 meters above sea level from municipality of Xalatlaco, as well water supply, sheep pen built with materials of metal grids and untreated wood, with dirt and concrete floors, and bed of straw that remained independently associated with infectious abortion in ewes. Approximately 80% of those respondents did not wear gloves or masks to prevent the transmission of the abortifacient zoonotic microorganisms. Conclusions: Sensitizing stakeholders on good agricultural practices could improve public health surveillance. Further studies on the effect of animal-human transmission in such a setting are worthwhile to further support the One Health initiative.

Sentinel-2 provides the opportunity to map the snow cover at unprecedented spatial and temporal resolution at global scale. Here we calibrate and evaluate a simple empirical function to estimate the fractional snow cover (FSC) in open terrain using the normalized difference snow index (NDSI) from 20 m resolution Sentinel-2 images. The NDSI is computed from flat surface reflectances after masking cloud and snow-free areas. The NDSI-FSC function is calibrated using Pléiades very high resolution images and evaluated using independent datasets including SPOT 6/7 satellite images, time lapse camera photographs, terrestrial lidar scans and crowd-sourced in situ measurements. The calibration results show that the FSC can be represented with a sigmoid-shaped function 0.5×tanh(a×NDSI+b)+0.5 where a = 2.65 and b = -1.42 yielding a root mean square error of 25%. Similar RMSE are obtained with different evaluation datasets with a high topographic variability. With this function, we estimate that the confidence interval on the FSC retrievals is 38% at the 95% confidence level.