In this work, the structural, magnetic, and mechanical properties of Nd16Fe76-xCoxB8 alloys varying the Co content at x = 0, 10, 20 and 25, were experimentally investigated by X-Ray Diffraction (XRD), Mössbauer Spectrometry (MS), Vibrating Sample Magnetometry (VSM) at room temperature (RT), and microhardness test were performed too. The system presents the hard Nd2Fe14B and the Nd1.1Fe4B4 phases for samples with x = 0 and 10. When concentration increases to x= 20 and 25, the CoO phase appears. All MS show the ferromagnetic behavior (eight sextets: sites 16k1, 16k2, 8j1, 8j2, 4c, 4e, sb) associated to the hard and soft magnetic phases, and one paramagnetic component (doublet: site d) associated to the minority Nd1.1Fe4B4 phase, which was not identified by XRD. All samples are magnetically hard present a hard magnetic behavior. The increase of Co content in these samples did not improve the hard magnetic behavior, but increased the critical temperature of the system and decrease the crystallite size of the hard phase. The hysteresis loop showed that predominates the Nd2Fe14B hard magnetic phase. There is a general tendency to increase microhardness with cobalt content, attributable to cobalt doping reduces the lattice parameters and porosities in the sample improving it hardness.

Blockchain decentralized applications (ÐApps) are applications which run on Blockchains nodes. Thus, in order to interact directly with this sort of applications, users need to have a blockchain address, wallet and knowledge about how to make transactions in order to interact with ÐApps. Therefore, the knowledge required to use a ÐApp can easily make users to desist when trying to interact with them. In order to tackle this issue, we propose a software architecture that will be located in the middle of the user and the ÐApp, thus making users initially unaware that they are interacting with a ÐApp. This is achieved by analyzing the relationship between ÐApps and Apps by using UML modelling. Next, based in the previous analysis, we created a middleware for users to interact with a ÐApp in the same manner the do with a traditional web app, i.e. by using usernames, passwords and UI elements instead of addresses, private keys or transactions. Finally, in order to put the developed middleware into practice, we developed a ÐApp that makes use of it. This ÐApp registers the time control of workers from companies by using Blockchain to store the data in a secure and non-modifiable manner.

After brings about a brief review of the theoretical explanations and researches on the reasons for being a victim, this article is organized into two sections. The first presents a comparative analysis of the data for 1999 and 2016 in terms of perceptions, profiles and most significant sociodemographic and socioeconomic variables. The second one shows an explanatory analysis based on a multivariate logistical regression model using as an independent variable lifestyle of the population and socioeconomic variables, and as dependent variables individual’s susceptibility to becoming a victim of certain crimes. The results points towards an explanatory model of victimization in which sociodemographic variables play an increasingly less important role while variables related to lifestyle and subjective perceptions make a significant contribution to greater understanding of the nature of being the victim of a crime.

Abstract: Coal bed methane (CBM) reservoirs are complex systems whose properties differ from those of conventional reservoirs. Coal seams are dual-porosity systems that comprise the porosities of the matrix and cleat system. Gas in the coal seams can be stored as free gas in the cleat system and as adsorbed gas in the porous medium. The flow mechanisms of the natural gas through the formation include desorption, diffusion, and Darcy’s flow regimes. The permeability of CBM reservoirs is more sensitive to pressure variations than conventional gas reservoirs. To study the flow behavior of CBM reservoirs it is mandatory to use a model that considers their unique characteristics. The objective of this study was to propose a physical and mathematical model of production performance for horizontal wells in CBM reservoirs whose permeability is dependent on pressure. A solution for the model was obtained by applying Pedrosa´s transformation, perturbation theory, Laplace transformation, the point source method, and Sthefest´s algorithm. The solution to this problem was validated with previous work thoroughly. The type curves of the model were built and the pressure transient behavior of the model was analyzed and discussed. The effects of several parameters on pressure behavior were also discussed.

Introduction: Determination of radiological bone age (BA) is a diagnostic method that consists of estimating chronological age (CA) from the bone maturation of children. Although environmental and hormonal factors can interfere with bone ossification, the process is essentially dependent on ancestral inheritance. These ethnic backgrounds are not usually considered, which can lead to biased interpretations and inadequate decision-making by pediatricians or forensic experts. The objective of this study was to determine the precision and accuracy of these radiological procedures among different ethnic groups. Methods: A qualitative systematic review carried out following MOOSE statement and previously registered in the International Prospective Registry of Systematic Reviews PROSPERO (CRD42023449512). Search was performed in MEDLINE (PubMed) (n=561), Cochrane Library (n=261), CINAHL (n=103), Web of Science (WOS) (n=181) and public institutional repositories (n=37) from inception to 31st December 2022 using Mesh as “Diagnostic Techniques and Procedures”, “Diagnostic imaging”, “Radiography”, “Age Determination by Skeleton” and free terms combining with booleans “AND” and “OR”. PEDro scale, and Risk of Bias in non-randomized Studies of Exposure (ROBINS-E) were used to assess methodological quality and risk of bias of included studies respectively. Results: 51 articles (n=19,531) were included according to the inclusion criteria previously established. There was a good to moderate methodological quality and a high to very high risk of bias. Skeletal methods for determining BA were precised in terms of intra-observer and inter-observer reliability in all ethnic groups. Regarding to accuracy of Skeletal methods in Caucasians and Hispanic children, GPA was accurate at all ages, but in youths, TW3 RUS could be a consistent alternative. In Asian and Arab, GPA and TW3 overestimated BA in adolescents near adulthood. In African youths, GPA overestimated BA while TW3 was more accurate in estimating CA. Dental and Cervical radiographic methods are equally precise but lesser accurate than Skeletal BA determination. Conclusion: Skeletal radiographic methods GPA and TW3 are both precise for BA determination among all ethnical groups, but their accuracy in estimating CA can be altered by racial bias.

The satisfaction of basic psychological needs leads students to engage in a sport modality on their own initiative. In the Spanish public educational system, mixed and heterogeneous, the gender and sport experience of students influence the teaching and motivation of invasion sports. This study investigated whether students' gender and sport experience, and method influence the psychological variables (basic psychological needs and sport adherence) when teaching school soccer and basketball. Furthermore, correlations were calculated between these psychological variables. The study involved 165 fifth and sixth grade students (age, 11.27 ± 0.68 years old) from several Spanish state schools in the same autonomous community. A non-random convenience sample was used. The needs for autonomy, perceived competence and social relationships were measured using the Basic Psychological Needs in Physical Exercise Scale. Sport adherence was measured using the Measure of Intentionality to be Physically Active. A Confirmatory Factor Analysis and Cronbach's alpha were used to analyze the psychometric properties of the scales. Descriptive and inferential analyses were performed with the Mann-Whitney U and Kruskal-Wallis H tests. There were significant differences in the needs for autonomy and perceived competence according to the students’ gender (boys > girls). Attending to sport adherence, there were also significant differences according to the students’ gender (boys > girls) and sport experience (experienced students > inexperienced students). Likewise, a regression analysis (structural equation model) revealed that the autonomy need showed low association with sport adherence. Higher perceived competence (β = 0.52) and social relationships (β = 0.36) were associated with greater adherence to sport (R2 = 0.65). Increased sport adherence will have health benefits.

The present study evaluates the psychometric properties of the Conflicts in Romantic Relationships Over Facebook Use Scale with a sample of Puerto Rican adults. A total of 577 Puerto Ricans participated on this confirmatory and psychometric study. The results confirmed that the scale has a multidimensional structure. These dimensions are: Partner Facebook intrusion, Conflict over Facebook use, and Jealousy over Facebook use. A total of 18 items complied with the criteria of discrimination and presented appropriate factorial loads (6 items per dimension). The Cronbach’s Alpha indexes of the dimensions ranged between .87 and .95 and the omega coefficients ranged between .88 and .95. In summary, the instrument has the appropriate psychometric properties to continue with validation studies, as well as to be implemented in various work areas, both theoretical and applied.

Instead of simplified steady-state models, with modern computers, one can solve the complete aero-thermodynamics happening in gas turbine engines. In the present article, we describe a mathematical model and numerical procedure to represent the transient response of a PT6A gas turbine engine operating at off-design conditions. The aero-thermal model consists of a set of algebraic and ordinary differential equations that arise from the application of the mass, linear momentum, angular momentum, and energy balances in each engine's component. The solution code has been developed in Matlab-Simulink using a block-oriented approach. Transient simulations of the PT6A engine start-up have been carried out by changing the original Jet-A1 fuel with biodiesel blends. Time plots of the main thermodynamic variables are shown, especially those regarding the structural integrity of the burner. Numerical results have been validated against reported experimental measurements and GasTurb simulations. The computer model has been capable to predict acceptable fuel blends, such that the real PT6A engine can be substituted to avoid the risk of damaging it.

Non-alcoholic fatty liver disease (NAFLD), a frequent complication of metabolic syndrome and visceral obesity, is characterized by marked accumulation of lipids in hepatocytes, accompanied by oxidant stress. In a substantial minority of cases, this progresses to steatohepatitis, which in turn can lead to life-threatening hepatic fibrosis and/or hepatocarcinogenesis. This essay analyzes the molecular biology underlying fat accumulation and oxidant stress in NAFLD, and identifies targets that can be addressed by nutraceutical or dietary measures. Nutraceuticals with potential for prevention or control of NAFLD – as suggested on theoretical grounds, and borne out by experience in rodent studies and/or clinical trials - include ferulic acid, melatonin, methylnicotinamide, tetrahydrocurcumin, nicotinamide riboside, carnosic acid, urolithin A, quercetin, high-dose biotin, citrulline, astaxanthin, long-chain omega-3 fatty acids, berberine, lipoic acid, silibinin, N-acetylcysteine, taurine, capsaicin, spermidine, spirulina, and carnitine. Some of these agents can also address the NLRP3 inflammasome activation and transforming growth factor-β signaling that play a role in driving the transition to steatohepatitis and fibrosis. In addition, soy isoflavones, via estrogen receptor-beta agonism, have anti-fibrotic potential, and supplemental glycine may blunt the contribution of Kupffer cells to the progression of NAFLD. Whole-food plant-based diets of modest protein content, owing to their impact on hormones such as fibroblast growth factor 21 and adiponectin, as well as on the obesity and metabolic syndrome underlying NAFLD, may also be protective in this syndrome. There is considerable potential for complex medical foods or nutraceutical supplementation regimens of rational design to aid prevention and control of NAFLD.

Urbanization has impacted biodiversity and ecosystems at a global scale. At the same time, it has been recognized as a driver of the gap between humans and nature. The lack of direct contact with nature can deteriorate several aspects of human wellbeing, and change knowledge and attitudes of people towards the environment. However, this phenomenon is still poorly understood in Megacities outside developed countries. Here, we explore the relationship between ecological knowledge and self-reported wellbeing in an important urban park in Santiago, Chile. We conducted semi-structured surveys to park users to explore their notions, preferences, ecological knowledge of plants and birds and self-reported wellbeing. Citizens associated urban parks mainly with “nature”, and particularly with the presence of trees and plants. Trees were recognized as the most relevant elements of urban parks, in turn, birds were ranked as the less relevant. Regarding ecological knowledge, respondents correctly identified an average of 2.01 plants and 2.44 birds out of a total of 10 for each taxon, and exotic species were more likely to be recognized. Park users also reported high scores for self-reported wellbeing. Interestingly, variance of self-reported wellbeing scores tended to increase at low levels of ecological knowledge of trees, but no significant relationship was detected with knowledge of birds, nor native species. These results suggest that parks can positively contribute to bring people closer to nature. Ecological knowledge was related to self-reported wellbeing. Improving ecological knowledge can be critical to restore the relationship between humans and nature in megacities.

This paper reports the novel design of a touch mode capacitive pressure sensor (TMCPS) system with a wireless approach for a full-range continuous monitoring of ventricular pressure. The system consists of two modules: an implantable set and an external reading device. The implantable set, restricted to a 2x2 cm² area, consists of a TMCPS array connected with a dual-layer coil, for making a reliable resonant circuit for communication with the external device. The capacitive array is modelled considering the small deflection regime for achieving a dynamic and full 5-300 mmHg pressure range. In this design, the two inductive-coupled modules are calculated considering proper electromagnetic alignment, based on two planar coils and considering the following: 13.56 MHz frequency to avoid tissue damage and three types of biological tissue as core (skin, fat and muscle). The system was validated with the Comsol Multiphysics and CoventorWare softwares; showing a 90% power transmission efficiency at a 3.5 cm distance between coils. The implantable module includes aluminum- and polyimide-based devices, which allows ergonomic, robust, reproducible, and technologically feasible integrated sensors. In addition, the module shows a simplified and low cost design approach based on PolyMEMS INAOE® technology, featured by low-temperature processing.

Wetlands are ecosystems that are essential to ecological balance and biodiversity, never-theless human activity is a constant threat to them. Excess nutrients are caused by inten-sive livestock and agricultural operations, pollution, and population growth, which in turn leads to uncontrolled microbiological development. This impairment in water quality can constitute a risk to animal, human, and environmental health. To thoroughly charac-terize the microbial communities, shotgun metagenomics was used to characterize the taxonomic and functional pattern of microorganisms that inhabit urban wetlands in the Los Lagos Region of Chile. The main objective was to identify microorganisms of veteri-nary relevance, assess their potential antibiotic resistance, and characterize the main vir-ulence mechanism. As expected, a high diversity of microorganisms was identified, in-cluding bacteria described as animal or human pathogens. Also, a diverse repertory of an-timicrobial-resistant genes (ARGs) was detected, which confers mainly resistance to be-ta-lactams, consistent with the families of antibiotics most used in Chile. Besides, a di-verse collection of virulence mechanisms was also identified. Given the significance of the relationship between environmental, animal, and human health—a concept known as One Health—there is a need to establish molecular surveillance programs. This work is the first report of the presence of these harmful biological elements in urban wetlands subjected to anthropogenic pressure, located in the south of Chile.

In the past decades, one of the most widely reported phenomena on Caribbean reefs is the general fall in coral cover and rise in macroalgae. Reefs with low coral cover and high macroalgal abun-dances are often presumed to provide poorer ecosystem functions and services. In this study, we assessed the condition of coral reefs on the Caribbean Coast of Costa Rica and determined how eight key ecosystem metrics varied in response to differential coral and fleshy macroalgae covers. Most reefs surveyed had high fleshy macroalgae and low live coral covers, with an average (± SD) of 31 ± 28% and 14 ± 13% per site. We found that the rugosity, urchin density, fish richness, total fish biomass, large fish density, and the potential fishery value of the reef were higher in sites with low fleshy macroalgae covers (>10%). The value of many of the ecosystem metrics estimated for coral reefs of the region appears to be lower than what’s been reported for other areas in the Caribbean, which may be related to the high macroalgae covers found on the reefs. Our results concur with the prevailing paradigm that an increase in macroalgae abundance could reduce the ecosystem services provided by coral reefs.

The Puuc Biocultural State Reserve (PBSR is an unique model for tropical dry forest conservation in Mexico. Preserving forest biodiversity and carbon within the PBSR depends on the mainte-nance of low impact productive activities coordinated by multiple communal and private land-owners. In this study, we used state-of-the-art remote sensing data to investigate past spatial patterns in forest clearing dynamics and its relation to forest carbon density and forest plant species richness and diversity in the context of the forest conservation goals of the PBSR. We used a Landsat-based continuous change detection product for the 2000-2021 period and compared it to carbon density and tree species richness models generated from ALOS-2 PALSAR 2 imagery and national scale forest inventory data. The estimated error-adjusted area of detected annual forest clearings from the year 2000 until the year 2021 was 230,511 ha in total (+19,979 ha). The analysis of annual forest clearing frequency and area suggests that although forest clearing was significantly more intensive outside of the PBSR than within the PBSR during the entire 2000-2021 period, there is no evidence suggesting that the frequency and magnitude of forest clearing has changed over the years after the creation of the PBSR in 2011. An emergent hotspot analysis shows, however, that high spatiotemporal clustering of forest clearing events (hotspots) during the 2012-2021 pe-riod was less common than prior to 2011 and these more recent hotspots have been confined to areas outside the PBSR. After comparing forest clearing events to carbon density and tree species richness models, results show that land owners outside the PBSR often clear forests with lower carbon density and species diversity than land owners inside the PBSR. This suggests that, compared to land owners outside the PBSR, land owners within the PBSR might be practicing longer fallow periods allowing forests to attain higher carbon density and tree species richness and hence better soil nutrient recovery after land abandonment. In conclusion, our results show that the PBSR effectively acted as a stabilizing forest management scheme during the 2012-2021 period minimizing the impact of productive activities by lowering the frequency of forest clearing events and preserving late secondary forests within the PBSR. We recommend the continuation of efforts for providing alternative optimal field data collection strategies and modeling techniques to spatially predict key tropical forest attributes. The combination of these models with contin-uous change detection datasets will allow to reveal underlying ecological processes and generate information better adapted to forest governance scales.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

The 1884 Andalusia Earthquake, with an estimated Magnitude between 6.2 and 6.7, is one of the most destructive events that shook the Iberian Peninsula, causing around 1200 casualties. Ac-cording to paleoseismology studies and intensity maps, the earthquake source relates to the nor-mal Ventas de Zafarraya Fault (Granada, Spain). Diverse studies registered and later analyzed hydrological effects, such as landslides, rockfalls, soil liquefaction, all-around surge and loss of springs, alterations in the phreatic level, discharge in springs and brooks, and well levels, along with changes in water properties. Further insight into these phenomena found an interplay be-tween hydro-geomechanical processes and crust surface deformations, conditions, and properties. This study focuses on analyzing and simulating the features involved in the major 1884 event and aims at elucidating the mechanisms concerning the mentioned effects. This ex-post analysis builds on the qualitative effects and visible alterations registered by historical studies. It encompasses conceptual geological and kinematic models, and a 2D finite element simulation to account for the processes undergone by the Zafarraya Fault. The study focuses on the variability of hy-dro-geomechanical features and the time evolution of the ground pore-pressure distribution in both the preseismic and coseismic stages, matching some of the shreds of evidence found by field studies. This methodology can be applied to other events registered in the National Catalogues of Earth-quakes to achieve a deeper insight, further knowledge, and a better understanding of past earth-quakes.

This research analyzes the Physical Education students’ degree of academic performance with the incorporation of active methodologies, specifically the flipped classroom mixed learning, restricted to evaluation periods in the months of June and September. The study focuses on whether there are significant differences in this variable through the scores obtained. Through a simple random sampling, 131 students participated in this empiric-analytic research, using an ex-post-facto study with a retrospective design with quasi control group. A robust test of averages comparison, multiple linear regressions and an evaluation of the relative importance of predictors is conducted. The results show how flipped classroom methodology linearly and positively influences academic performance and correlationally motivation and support. As main conclusion, in a hybrid and digitalized learning context, the value of the consideration of active methodologies (flipped classroom) based on emerging pedagogies, allows improving students’ achievement and competence development, providing critical, significant, ubiquitous, transformational and especially motivating experiences.

Among the knowledge areas in which process mining has had an impact, the audit domain is particularly striking. Traditionally, audits seek evidence in a data sample that allows to make inferences about a population. Mistakes are usually committed when generalizing the results and anomalies, therefore, appear in unprocessed sets. However, there are some efforts to address these limitations using process mining-based approaches for fraud detection. To the best of our knowledge, no fraud audit method exists that combines process mining techniques and visual analytics to identify relevant patterns. This paper presents a fraud audit approach based on the combination of process mining techniques and visual analytics. The main advantages are: (i) a method is included that guides the use of the visual capabilities of process mining to detect fraud data patterns during an audit; (ii) the approach can be generalized to any business domain; (iii) well-known process mining techniques are used (Dotted Chart, Trace Alignment, Fuzzy Miner…). The techniques were selected by a group of experts and were extended to enable filtering for contextual analysis, to handle levels of process abstraction, and to facilitate implementation in the area of fraud audits. Based on the proposed approach, we developed a software solution that is currently being used in the financial sector as well as in the telecommunications and hospitality sector. Finally, for demonstration purposes, we present a real hotel management use case in which we detected suspected fraud behaviors, thus validating the effectiveness of the approach.

'Cv 'Doña María' table grape is a high-quality table grape variety included in the Protected Designation of Origin (PDO) of the European Union "The bagged grape of the Vinalopó." The PDO stipulates that grape clusters must be protected with paper bags from inclement weather and insects, which helps enhance the final grape quality. However, 'Doña María' is a variety prone to high shattering in the late stages of ripening on the vine and during postharvest. Inorganic calcium treatments are one of the most commonly used tools to reduce this disorder, but the translocation of this mineral from veraison onward has been questioned. In this study, five applications were performed, from veraison to harvest, using sorbitol-chelated calcium (0.7 % + 1.0 %), Ca(NO3)2 (Ca) at 0.7% and sorbitol at 1%. It was observed that bagged grapes (not wetted with the solutions) only increased the concentration of total and bound calcium when treated with Sorbitol-Ca. This resulted in reduced berry drop during cultivation and postharvest and improved fruit firmness. Additionally, it reduced grape metabolism indicators such as respiration rate, weight loss, malic acid degradation, prevented abscisic acid (ABA) and malondialdehyde (MDA) accumulation, and favored the accumulation of secondary metabolites such as total polyphenols, increased antioxidant activity, and sugar content. The application of sorbitol-chelated calcium is an effective and safe tool that enhances fruit quality and prevents losses due to shattering during postharvest.

Maize (Zea mays sp) is one of the most important basic grains in our diets, and requires high levels pf nitrogen and phosphorus for optimum growth. However, phosphorus is problematic due to its high reactivity in the soil matrix, meaning that it is fixed in a very short time and inaccesible to plants. The lupinus genus, and more specifically, Lupinus albus through its root clusters, or proteoid roots, have the ability to solubilize portions of phosphorus when it is found in a limited environment. The objetive of the current study was to evaluate the effect of lupinus montanus under phosphorus stress conditions intercropped with maize, utilizing sandy soils with calcium phosphate bands. Materials and Methods: Work was conducted in growth chambers using rhizotrons, which allowed the authors to observed the growth and root behavior of both species (Lupinus monatnus and maize), The SAS 9.0 program was used for the statistical Analysis and ANOVA and tukey test were perfomed. Results : The phosphorus analysis in the plant tissue indicated that is concentration in maize was slightly higher in intercropping conditions than in monoculture planting. Conclusion: From this, we calculated that lupinus montanus is capable of solubilizing portions of phosphorus making available for other crops.; likewise, we also observed that proteoid structures did not develop, leaving the study open for other wild species.

The aim of this study was to use latent profile analysis to identify specific profiles of burnout syndrome in combination with work engagement and to identify whether job satisfaction, psychological well-being, and other sociodemographic and work variables affect the probability of presenting a profile of burnout syndrome and low work enthusiasm. A total of 355 healthcare professionals completed the Spanish Burnout Inventory, the Utrecht Work Engagement Scale, the Job Satisfaction Scale, and the Psychological Well-Being Scale for Adults. Latent profile analysis identified 4 profiles: 1) burnout with high indolence (BwHIn); 2) burnout with low indolence (BwLIn); 3) high engagement, low burnout (HeLb); and 4) in the process of burning out (IPB). Multivariate logistic regression showed that a second job in a government health care institution; a shift other than the morning shift; being divorced, separated or widowed; and work load are predictors of burnout profiles with respect to the HeLb profile. These data are useful for designing intervention strategies according to the needs and characteristics of each type of burnout profile.

Plant pathogenic fungi are the most important cause of losses in agriculture. In the face of the overuse of synthetic fungicides, natural products are an encouraging alternative to control these plant pathogenic fungi. In this study, we tested the antifungal capacity of metabolites produced by strains of the genus Streptomyces against the plant pathogenic fungi Alternaria alternata, Botrytis cinerea and Fusarium oxysporum. In addition, we investigated the feasibility of applying these metabolites in a postharvest setting for the control of B. cinerea on cherry tomato fruits. The results revealed the ability of the strains, especially Streptomyces netropsis, to inhibit the growth of plant pathogenic fungi and, in some cases, the sporulation of these fungi. In addition, we observed an interesting phenomenon in which Streptomyces strains physically encapsulated the mycelium of the fungi, which contributed to their inhibition. Finally, the protective activity of S. netropsis extract on Cherry tomato fruits infected with B. cinerea was demonstrated. In conclusion, this research opens the door to studies on the understanding of physical microbial interactions in natural environments and holds promise in agriculture, especially in the protection of agricultural products during the post-harvest stage as a safer and more sustainable alternative.

Objective: The goal of this study was to analyse the attitudes and perceptions of emergency and mental health nurses through the validation of the SM-GIBED scale in specialised care in Spain on alcoholics and other drug-dependent patients. Design and Setting: This cross-sectional study was developed using the Spanish hospital version of the Seaman-Mannello scale to denominate the SM-GIBED scale. Participants: 170 Emergency and Mental Health Nursing from five Spanish Hospitals. Intervention: Self-administered questionnaire to analiyse the perceptions and attitudes about the drug addict and the alcoholic. Primary and Secondary Outcome Measures: A descriptive and inferential analysis of the study variables was carried out. A psychometric analysis was performed to validate the scale. Results: A total of 170 questionnaires were collected from 257 healthcare workers. Overall, 99.1% of the participants had contact with drug-dependent patients during their professional experience. Nearly 75% had difficulties in treating them. The psychometric analysis of the SM-GIBED scale in the Spanish context obtained values of KMO = 0.655 and Bartlett's test p < 0.000. Cronbach's alpha of 0.738 was obtained from the reliability analysis. A reliability analysis of each of the SM-GIBED questions found no case with an alpha lower than 0.71. In conclusion, positive aspects include an ingratiating attitude and subject-to-subject communication when nurses self-define as empathic and non-paternalistic. Among the negative aspects, there is a lack of communication skills and assertiveness with these patients. This highlights a certain degree of resignation and dissatisfaction when working with drug addicts.

The objective of this research was to study the dynamics of moisture and nutrition at the root zone and to quantify the variables linked to efficient water management in avocado orchards of mid and high-lands of Michoacán, México, in typical Andisols of low fertility with (A)C(w2) and C(w2) climates, respectively. Using the FDR (Frequency Domain Reflectometry) technology, the dynamics of soil moisture and salinity were recorded daily at four depths: 0-15, 15-30, 30-45, and 45-60 cm. The soil moisture balance model was used to determine actual evapotranspiration (ETr), crop coefficient (Kc), and water use efficiency (WUE). Results indicated that ETr is 66-73% of the total water at 0-30 cm depth; the fertilizer absorption is limited to 0-30 cm, being negligible at deeper layers. The water use efficiency is 4.4 to 5.6 kg of fruit m-3 of applied water, and the ratio of the water use index (ETr/irrigation sheet applied, ISA) is 0.65-0.70; while the annual avocado Kc is 0.72 in Cutzato and 0.78 in Tiamba. We concluded that avocado has a low water requirement, it does not cause leaching of nutrients and/or water, the absorption of water and nutrients mostly occurs at 30 cm depth, and from a hydrological point of view, the crop is environmentally friendly.

Background: Empathy and assertiveness are two essential soft skills for health professionals such as nurses or physiotherapists. Both professions are characterised by their contribution to preserving and improving health and human care, and for their vocation of service. One of the achievements of the training is the voluntary, conscious, and individually inspired career choice; Objetives: This study aimed to evaluate the empathy, assertiveness, and care vocational levels among undergraduate students enrolled in the Nursing and Physiotherapy Degree programmes and to investigate the relationship between these soft skills and the care vocation; Methods: A cross-sectional study of nursing and physiotherapy students was conducted in the 2022/2023 academic year. The Interpersonal Reactivity Index scales for empathy, the Rathus test for assertiveness, and the “Vocation of Service for Human Care” questionnaire were used as study tools. Finally, 226 students participated in the study; Results: The empathy, assertiveness and vocation of service for human care of the students was found to be acceptable. Significant differences were also observed according to the gender variable or career in the students, with female students presenting better results in empathy subscales or vocation (p < 0.05). Students who are working or have clinical experience in other professions score lower on the empathy personal distress subscale (p < 0.05); Conclusions: Both nursing and physiotherapy students demonstrate satisfactory levels of empathy, assertiveness and vocation for human care. However, gender and previous work experience do notably influence these scores. It would be beneficial to conduct long-term studies with educational interventions to train and develop empathy, assertiveness and vocation for human care.

Antimicrobial resistance has been stated to be a global health problem. In Chile, the use of antibiotics should be declared by medical prescription, however, it is unknown what happens to the drugs once the treatment ends. One possibility is that these end up being disposed of in the trash or down the drain. In both scenarios, antibiotics could accumulate in the environment, stimulating the emergence of antimicrobial resistance mechanisms and their transfer between microorganisms. Unfortunately, sometimes wastewater ends up in bodies of water, due to the dragging of elements by rain, or by the presence of illegal water discharges. In this work, we use shotgun metagenomics to elucidate the functional and microbial composition of biohazard elements in the bay of Puerto Varas City, Chile. As expected, we found a high diversity in microbial communities, with bacterial elements described as human or animal pathogens. Also, we detect a diverse repertory of virulence and antibiotic-resistant genes (ARGs), related with macrolides, beta-lactams, and tetracyclines resistance, which are consistent with the families of antibiotics most used in Chile. Similar ARGs were identified in DNA mobile elements. In addition, we tested the AMR ability in 20 bacterial strains recovered from the Llanquihue lake. This is the first report of the presence of genomic elements that could constitute a health problem for the people who live around the Llanquihue Lake of Chile, considering the importance of the interconnection between environmental, animal, and human health, a concept known as One Health.

This research was carried out to know the species composition of the Arbuscular Micorrhizal Fungi (AMF) communities native to two contrasting soils, and to establish the development and stability of aggregates in those soils contained in pots, as substrates for corn plants in the greenhouse. These soils were inoculated with allochthonous AMF. The experiment had three factors: Soil (S with two levels [S1 and S2]); AMF (A with three levels: without application [A0], with application of Claroideoglomus claroideum [A1] and with application of a consortium [A2]) and Fertilization (f with two levels (without fertilization [f0] and with fertilization [f1]); which generated 12 treatments, each with five replicates (60 experimental units [EU]); the EU consisted of a pot with a plant of corn; with a completely random distribution. The results showed that the Typic Ustifluvent presented nine species of native AMF, while the Typic Dystrustert had only three species. The native AMF in each soil influenced the activity of the allochthonous AMF, with differences being found in the stability of the macro-sized aggregates (0.5 to 2.0 mm) of each soil when they did not receive fertilization

Measuring host communities' perceptions and attitudes towards tourism development has been increasingly common since the mid-1970s. The greater the growth of the tourism industry worldwide, the more relevant it has become to assess the impact of tourism activity on the local residents. In this paper we present the results of a study carried out in two EU countries highly dependent on tourism act though at a different stage of development. Our findings are based on qualitative and quantitative data obtained via a questionnaire survey designed in pre-covid 19 times to analyze the perceptions and attitudes of tourism college students from Croatia and Spain, today’s tourism employers and employees, towards tourism development in sun and sea desti-nations. Our aim is to contrast the hypothesis that the nationality of our sample is a significant variable when evaluating the socioeconomic and environmental impact of the development of the tourism industry. Croatia’s workforce, the most highly dependent on the EU travel and tourism industry show to be much more aware of the negative impacts of tourism development than their Spaniards counterparts; showing a tourism workforce more reluctant to further tourism development.

The architectural configuration of the space plays a crucial role in the acoustics of Neonatal Intensive Care Units (NICUs). The design of the environment, the materials used in construction, and the organisation of noise sources within the room significantly influence the noise levels present in these critical areas. For this research, noise levels found in two hospitals, with different architectural configurations and sizes but similar construction materials, have been analyzed. Data were recorded at 1-second intervals over a period of more than 24 hours. The data collected in these hospitals confirm the magnitude of the noise problem in NICUs, highlighting the urgent need to address it effectively to ensure an appropriate and safe environment for the recovery of neonates. Good architectural planning can help mitigate noise, while poor configuration can exacerbate acoustic problems, negatively affecting both patients and healthcare staff. It is crucial to involve architects, acoustic engineers, and healthcare staff in the design and renovation of NICUs to create spaces that not only meet medical needs but also consider the auditory well-being of neonates.

This study aimed to investigate the influence of cranio-cervical position on the electromyographical activity of the core muscles during the prone plank exercise. Twenty healthy participants were enrolled in this study. Muscle activation was registered using surface electromyography (sEMG) in the rectus abdominis (RA), external oblique (EO), internal oblique (IO) and lumbar portion of erector spinae (LES). Three prone plank conditions were randomly evaluated, varying the position of the cranio-cervical segment during the prone plank performance (NEUTRAL, FLEXION and EXTENSION). sEMG signals of each individual muscle, Total Intensity (TI) and ratings of perceived exertion (RPE) were analysed with statistical significance set at P&lt;0.05. FLEXION revealed significantly higher TI values compared to NEUTRAL and EXTENSION (p = 0.000; effect size (ES) &gt; 0.90). The RA presented larger activation in FLEXION compared to the other variations (p &lt; 0.05; ES &gt;0.70). FLEXION elicited a greater response compared to NEUTRAL for both sides of EO when compared to EXTENSION, and also for both sides of IO compared to the other conditions. Both FLEXION and EXTENSION reported higher RPE values compared to NEUTRAL. Cranio-cervical segment position influenced the electromyographical activation of core musculature, showing highest values when performing prone plank in a cranio-cervical flexion.

Chronic Obstructive Pulmonary Disease (COPD) is a disease characterized by local and systemic inflammation independently of the risk factor; during the exacerbations, such inflammation is accentuated and amplified. A practical inflammatory marker and one with an applicable predictive value in the follow-up has been sought. FeNO has shown an excellent performance in that respect within the context of asthma and has also been studied in tobacco-smoke COPD (COPD-TS). In Biomass-smoke COPD (COPD-BS), this, to our knowledge, has not been evaluated. Objective: To measure FeNO levels in patients with COPD-BS and to compare these with those of patients with stable COPD-TS and in healthy controls. Methods: Transversal, observational, descriptive, comparative, and analytical study. A total of 57 patients, including 23 with COPD-BS, 17 with COPD-TS, and 17 healthy control subjects. The measurement of FeNO was carried out on all of these by means of the on-line chemiluminescence technique; the values were expressed in parts per billion (ppb) for their analysis. Results: It was observed that the FeNO values were similar between COPD-BS and COPD-TS and were significantly different between the healthy and stable COPD (both groups). No correlation was found between pulmonary function and symptoms with FeNO in any of the groups. Conclusions: The level of FeNO in stable COPD is found to be increased in a similar manner in COPD-BS and COPD-TS, with a significant difference on comparing it with that of the healthy subjects.

In this work, we propose a variation of the cellular particle swarm optimization algorithm with differential evolution hybridization (CPSO-DE), to include constrained optimization in it, named Ts-CPD. It is implemented as a kernel of electronic design automation (EDA) tool capable of sizing circuit components considering a single-objective design with restrictions and constraints. The aim is to improve the optimization solutions in the sizing of analog circuits. To evaluate our proposal’s performance, we present the design of three analog circuits: a deferential amplifier, a two-stage operational amplifier, and a folded cascode operational transconductance amplifier. Numerical simulation results indicate that Ts-CPD can find better solutions, in terms of the design objective and the accomplishment of constraints, than those reported in previous works.

Cellular automata are mathematical models that represent systems with complex behavior through simple interactions between their individual elements. These models can be used to study unconventional computational systems and complexity. One notable aspect of cellular automata is their ability to create structures known as gliders, which move in a regular pattern to represent the manipulation of information. This paper introduces the modification of mean-field theory applied to cellular automata, using random perturbations based on the system’s evolution rule. The original aspect of this approach is that the perturbation factor is tailored to the nature of the rule, altering the behavior of the mean-field polynomials. By combining the properties of both the original and perturbed polynomials, it is possible to detect when a cellular automaton is more likely to generate gliders without having to run evolutions of the system.This methodology is a useful approach to finding more examples of cellular automata that exhibit complex behavior. We start by examining elementary cellular automata, then move on to examples of automata that can generate gliders with more states. To illustrate the results of this methodology, we provide evolution examples of the detected automata.

In the food industry, Listeria is a standard control microorganism in ready-to-eat food since it may be pathogenic and cause a disease called listeriosis. The objective of the present study was to carry out a challenge test to verify the efficiency of different combinations of natural antimicrobial ingredients, against Listeria monocytogenes, to be used in ready-to-eat foods. Six different formulations of cooked ham were elaborated: a control, and five different formulations. An initial inoculation of 2 log cycles was used in the different products and the growth of Listeria was monitored at different temperatures and times (4° C for 17 w; 7ºC for 12 w). Control samples showed a progressive growth, reaching 5-6 log after 3 or 4 weeks. The rest of samples showed constant counts of Listeria during the all study. Only samples containing: 100 ppm nitrite + 250 PPM ascorbic acid+0,7% PRS DV-5 did not control the growth of Listeria at 7 ° C after 7 w of storage. The results obtained allowed to classified the cooked ham elaborated using any natural ingredients combinations as a “Ready-to-eat food unable to support the growth of L. monocytogenes other than those intended for infants and for special medical purposes”.

Maintaining a healthy cyber society is a big challenge due to the users’ freedom of expression and behaving. It can be solved by monitoring and analyzing the users’ behavior and taking proper actions towards them. This research aims to present a platform that monitors the public content on Twitter by extracting tweet data. After maintaining the data, the users’ interactions are analyzed using Graph Analysis methods. Then the users’ behavioral patterns are analyzed by applying Metadata Analysis, in which the timeline of each profile is obtained; also, the time-series behavioral features of users are investigated. Then in the Abnormal Behavior Detection Filtering component, the interesting profiles are selected for further examinations. Finally, in the Contextual Analysis component, the contents will be analyzed using natural language processing techniques; A binary text classification model (SVM + TF-IDF with 88.89% accuracy) for detecting if the tweet is related to crime or not. Then, a sentiment analysis method is applied to the crime-related tweets to perform aspect-based sentiment analysis (DistilBERT + FFNN with 80% accuracy); because sharing positive opinions about a crime-related topic can threaten society. This platform aims to provide the end-user (Police) suggestions to control hate speech or terrorist propaganda.

In this paper, an iterative procedure to find the solution of a nonlinear structural model is introduced. The model presents different multiplicities where parameters are randomly selected within a solvability region. To achieve this aim, a class of multipoint fixed-point iterative schemes for single roots is modified to find multiple roots, reaching the fourth order of convergence. Complex discrete dynamics techniques are employed to select the members with the most stable performance. The structural problem, as well as some academic problems involving multiple roots, are solved numerically to verify the theoretical analysis, robustness and applicability of the proposed scheme.

Considering Cu(tda) chelate is a receptor for adenine and related 6-aminopurines, now we report the synthesis, molecular and crystal structures, thermal stability, spectral properties and DFT calculations on the [Cu(tda)(9heade)(H2O)]•2H2O (1). N7 is found to be the preferred donor atom of 9heade, that can favor the cooperation of a Cu-N7(9heade) bond and an (9heade)N6-H•••O(tda) interligand interaction. But unprecedentedly, the Cu(tda)-9heade molecular recognition in 1 is essentially featured the Cu-N1(9heade), without any N6-H•••O(carboxyl tda) interligand interaction. Nevertheless, being N1 the most basic donor for N9-substituted adenines, this Cu-N1 bond is now assisted by an O2-water mediated interaction (N6-H•••O2 and O2•••Cu weak contact). Also in the crystal packing, the O-H(ol) of 9heade interacts with its own adenine moiety by an O3-water mediated interaction (O(ol)-H•••O3 plus O3-H36•••π(adenine moiety). In turn these water-mediated interactions seems to be responsible to serious alterations on the physical properties of crystalline or grounded samples. Density functional theory calculations were used to evaluate the interactions energetically. Moreover, the quantum theory of atoms-in-molecules (QTAIM) in combination with the noncovalent interaction plot (NCIPlot) were used to analyze the interactions and rationalize the existence and relative importance of hydrogen bonding, chalcogen bonding and π-stacking interactions.

Background: The incidence of prostate cancer (PC) has been risen annually. Despite the diagnosis is made mainly with non-metastatic PC, mortality is explained by the metastatic disease (mPC). Without a doubt there is an intermediate scenario in which patients have no mPC but will have initiated a metastatic cascade through an epithelial-mesenchymal transition. There is indeed a need for more and better tools to predict what patients will progress in the future to non-localized clinical disease or already have micrometastatic disease, and therefore, will clinically progress after primary treatment. Biomarkers for predicting mPC are still under development; there are few studies and not much evidence of their usefulness. Summary: This review is focused on tissue-based genomic biomarkers (TBGB) for predicting metastatic disease. We developed four main research questions that will attempt to answer according to the current evidence. Why is important to predict metastatic disease? Which tests are available to predict metastatic disease? What impact should there be on clinical guidelines and clinical practice in predicting metastatic disease? What are current prostate cancer treatments? Key Messages: Knowing useful predict tools could help determine which patients may need multimodal or adjuvant treatment even with a localized disease, and in consequence, what patients do not need more than a single modality of treatment. The importance of predicting metastasis is fundamental, given that once metastasis is diagnosed, the quality of life (QoL) and survival drop dramatically.

Anonymous communications networks were born to protect the privacy of our communications, preventing censorship and traffic analysis. The most famous anonymous communication network is Tor. This anonymous communication network provides some interesting features, among them, we can mention user’s IP location or Tor Hidden Services (THS) as a mechanism to conceal the location of servers, mainly, web servers. THS is an important research field in Tor. However, there is a lack of reviews that sump up main findings and research challenges. In this article we present a systematic literature review that aims to offer a comprehensive view on the research made on Tor Hidden services presenting the state of the art and the different research challenges to be addressed. This review has been developed from a selection of 57 articles and present main findings and advances regarding Tor Hidden Services, limitations found, and future issues to be investigated.

The present study investigates the impact of electrode surface roughness on the electrofreezing of water. This research focuses on how the electrode roughness induced by a laser treatment affects the nucleation and growth of ice crystals under controlled electric fields. To achieve this, a series of experiments were conducted using deionized water samples placed between electrodes with varying surface roughness. The electrodes, fabricated with the Al6061 T6 alloy were structured via the Laser Shock Processing (LSP) method. For this purpose, the pulsed densities during the LSP process were varied from 900 to 2500 pulses/cm2. The increase of the pulse density was correlated to the surface structuring and to the microstructural features and average roughness of the LSP-treated Al6061 alloy. A wavy-like microstructure was induced upon the LSP treatment with average roughnesses between ~ 3.5 and 6 µm at the selected pulse densities. The results indicate that electrode roughness significantly influences the electrofreezing process. Rougher electrodes were found to lower the nucleation temperature compared to smoother ones, suggesting enhanced ice nucleation activity. The findings are attributed to the increased electric field concentration at the asperities of the rough surfaces, which may facilitate the alignment of water molecules and the formation of critical ice nuclei.

Forest management aims to preserve ecosystem integrity, maintaining resilience thresholds. For this, conservation and invasion patterns must be determined in managed landscapes. The objective was to identify proxies (landscape and environmental patterns) that allowed the plant species invasion and define thresholds of human impacts to improve management practices. We also want to identify indicator species for the different kinds of impacts and environments. 165 plots were measured in Nothofagus antarctica forests and associated open-lands (dry and wet grasslands) in Tierra del Fuego (Argentina). We found differences in the studied variables across landscape and among different uses and impact types. Human impacts influenced over land types, emphasizing the importance of managing intensities. Indicator plant species allowed to identify potential ecological thresholds related to human impacts and the establishment of species linked to ecological and economic degradation, e.g. Bolax gummifera and Azorella trifurcata were associated with high grazing pressure in grasslands and fire in forested areas, while Rumex acetosella and Achillea millefolium, typically associated with forested areas, were related to high harvesting pressure and fire impacts. These findings contribute to understanding the long-term effects of some impacts, and allow us to define variables of monitoring and indicator species for each impact type.

Visual thinking leverages spatial mechanisms in animals for navigation and reasoning. Therefore, given the challenge of abstract mathematics and logic, spatial reasoning-based teaching strategies can be highly effective. Our previous research verified that innovative box and ball coloring activities help teach elementary school students complex notions like quantifiers, logical connectors, and dynamic systems. However, given the richness of the activities, correction is slow, error-prone, and demands high attention and cognitive load from the teacher. Moreover, feedback to the teacher should be immediate. Thus, we propose to provide the teacher with real-time help with LLMs. We explored various prompting techniques with and without context Zero shot, Few shot, Chain of Thought, Visualization of Thought, Self Consistency, logicLM and Emotional to test GPT-4o’s visual, logical, and correction capabilities. We obtained that Visualization of Thought and Self Consistency techniques enabled GPT-4o to correctly evaluate 90% of logical-spatial problems that we tested. Additionally, we propose a novel prompt combining some of these techniques that achieved 100% accuracy on a testing sample, excelling in spatial problems and enhancing logical reasoning.

Cocoa bean quality depends mainly on genetic material, edaphoclimatic factors and post-harvest processes such as fermentation. The impact of the fermentation process on the chemical and func-tional composition of different cocoa clones grown in southern Colombia was analyzed. A facto-rial design with repeated measures over time was used to analyze the effect of clone and fermen-tation time on chemical characteristics (bromatology, phenolic compounds and antioxidant ac-tivity). The bromatological characteristics showed significant differences between clones and fermentation time. Clones EET-8 and CCN-51 showed higher contents of acidity (0.51%), fat (63.61%), protein (12.85%) and carbohydrates (1.63 mg g-1). Moisture, acidity and sucrose in-creased their values between day 4 and day 6 of fermentation (P<0.05). Phenolic compounds and antioxidant activity had significant differences between clones, where clones CCN-51 and ICS-95 had high contents of phenols (64.56 mg g-1), flavonoids (3.30 mg g-1) and DPPH reducing capacity (325.55 µmol g-1). In this sense, we consider the FSV-41 clone as the major grain quality index based on the results of chemical composition at bromatological level, antioxidant activity and phenolic compounds.

In this paper, we present a three-step sixth-order iterative schemes to estimate the solutions of a nonlinear systems of equations, for predicting the shear strength of a reinforced concrete beam. This procedure is designed by means of a weight function technique. The values for the parameters of this system were randomly selected inside the prescribed ranges by technical standards for structural concrete; moreover, some of this parameters were fixed taking into consideration the solvability region of the adopted steel constitutive model. The efficiency of the new class is compared with other current schemes, with very good results.

Fabry disease is a lysosomal storage disorder caused by the deficiency of the α-galactosidase-A enzyme. Cardiac, renal, and neurological involvement significantly reduces life expectancy. Until a few years ago, treatment options for Fabry disease were limited to enzyme replacement therapy with agalsidase alfa or beta administered by intravenous infusion every 2 weeks. Migalastat (Galafold®) is an oral pharmacological chaperone that increases enzyme activity of “amenable” mutations. The safety and efficacy of migalastat were supported in the phase III FACETS and ATTRACT studies, compared to available enzyme replacement therapies; showing a reduction in left ventricular mass, and stabilization of kidney function and plasma Lyso-Gb3. Similar results were confirmed in subsequent extension publications, both in patients who started migalastat as their first treatment and in patients who were previously on enzyme replacement therapy and switched to migalastat. In this review we describe the safety and efficacy of switching from enzyme replacement therapy to migalastat in patients with Fabry disease and “amenable” mutations, referring to publications available to date.

Turbulent flow is the first and fundamental physical phenomena to evaluate when optimising cost and reducing emissions from an Anode Baking Furnace (ABF). Gas flow patterns, velocity field, pressure drop, shear stress, and turbulent dissipation rate variables are the main operational parameters to be optimised, considering a specific geometry. Computational Fluid Dynamics (CFD) allows simulating physical phenomena using numerical methods with computer resources. In particular, the finite element method is one of the most used methods to solve the flow equations. This method requires a discretisation of the geometry of the ABF, called mesh. Hence, mesh is the main input to the finite element method. A suitable mesh for applying a discretisation method determines whether the problem can be simulated or not. Generating an appropriate mesh remains a challenge to perform accurate simulations. In this work, a comparison between meshes generated using two mesh generation tools is presented. Results of different study cases are included.

The acoustic environment in learning spaces significantly influences learning effectiveness and occupant well-being. Recent studies have shown that a series of architectural factors within physical learning environments can impact students' educational experiences. This research delves into the relationship between architectural characteristics and the perceived acoustic environment among 467 primary students in 19 learning spaces across 9 schools in Chile. The survey comprises a student questionnaire, a checklist evaluating space characteristics, and acoustic measurements of indoor noise levels during occupied conditions. Examined topics include Indoor Environmental Quality (IEQ) comfort perception, noise annoyance, hearing ability, and acoustic preference. Architectural characteristics considered encompass flexible and acoustic space design parameters. The results indicated that noise discomfort was a common issue, especially in traditional learning spaces without acoustic treatment. The type of learning space (traditional or flexible settings) has a greater impact on acoustic perception particularly concerning noise discomfort and acoustic preference. However, poorly acoustic spaces lacking absorbing materials or exhibiting lower spatial density (m2 per student) contribute to increased indoor noise levels affecting noise annoyance caused by children's talking inside. The study emphasizes the importance of considering both architectural design and acoustic conditioning for optimizing the acoustic experience in educational spaces.

Oral pyogenic granuloma (PG) is generally a solitary benign connective tissue proliferation of unknown etiology. It is the most common type of oral inflammatory hyperplasia histologically characterized by proliferation of granulation tissue with inflammatory infiltrates and high angiogenic capacity. Vascular neoformations of different diameters are usually present. Due to their structural characteristics, tendency to bleed, and rapid and alarming growth rate, these neoformations may have serious consequences. Sometimes, it is complex to make an accurate diagnosis. Therefore, adequate management and treatment are based on the characteristics and systemic conditions of each patient. This review was carried out to provide an overview of the factors involved in, or attributed to the etiopathogenesis of oral PG. It describes the different forms of presentation and clinical evolution, as well as the most frequent signs and symptoms that characterize this disease, while incorporating recent radiographic and microscopic findings. In addition, it describes the different modalities for the management of oral pyogenic granuloma depending on the particular characteristics of each patient.

In this study, four samples of recycled aggregates from construction and demolition waste of Mexico City were characterized, in order to find innovative uses for this type of materials. Gravel and sand from a recycling plant were analyzed, as well as recycled aggregates in the laboratory from demolished concrete collected in landfills. The characterization was carried out by means of XRD, chemical microanalysis (EDS), pH measurement and sieve analysis. The results reveal that the minerals present in the analyzed materials are triclinic feldspars, cristobalite and pyroxene which correspond to the natural aggregates, as well as variable amounts of calcite, product of the carbonation of the cement paste adhered to these aggregates and in a smaller proportion calcium hemicarboaluminate, rosenhanite and tobermorite. It was determined that the quality (amount of cement) of the original concrete that was recycled, has great influence on the granulometry and the chemical-mineralogical composition of the aggregates, since there will be different quantities and qualities of cement paste adhered to the aggregates of according to size. Finally the pH values measured in all samples fluctuate between 10.15 and 12.08, therefore it is suggested that these materials can be used in soil stabilization.

In birds, unlike mammals, there is no complete separation between the thoracic and abdominal cavities. Instead, they have the coelomic cavity where most main organs are found. Therefore, an adequate knowledge of the anatomy of the coelomic cavity is of great importance for veterinarians, biologists and the scientific community. This study aimed to evaluate the coelomic cavity anatomy in the Atlantic puffins (Fratercula Arctica) using anatomical sections and computed tomography images.

We aimed to assess the caffeine intake before and during pregnancy, compliance with caffeine recommendations during pregnancy (200 mg/day) and factors associated with higher intakes before and in first trimester of pregnancy. Caffeine consumption was collected in a Spanish cohort of pregnant women through a validated food questionnaire, before and in each trimester of gestation (T1, T2 and T3). 463 pregnant women were recruited and follow-up through pregnancy. Compliance with caffeine intake recommendations during pregnancy and quintiles of mg/day of caffeine before and in T1 of pregnancy were calculated. A multivariate logistic regression, comparing extreme quintiles of consumption (Q1 vs Q5) was used. Mean caffeine intake before pregnancy was 120.05 mg/day (SD 117.85), 42.76 mg/day (SD 63.90) at 12th GW, 42.00 mg/day (SD 59.76) at 24th GW and 39.34 mg/day (SD 50.9) at 32nd GW (p&lt;0.001). 86% of women complied with caffeine recommendations during pregnancy. At pregnancy (T1), being an active smoker was associated with Q5 &gt; 100.1 mg/day, aOR = 22.69; 95% CI 4.67- 110.26. igh diet quality, aOR = 0.30; 95% CI, 0.13- 0.68, and moderate physical activity level, aOR= 0.44; 95% CI, 0.19-1.00, were inversely associated with Q5 &gt; 100.1 mg/day. Pregnant women are mostly adhering to current caffeine intake guidelines. Higher caffeine intake at pregnancy is associated with other unhealthy habits during pregnancy.

In Mexico there is a deficit in the production of pine resin, because it depends on natural forests. Therefore, it is necessary to select provenances and phenotypes of potential species such as P. oocarpa. The objective was to determine the difference between provenances and the variation of resin components and quality, as well as the effect of geographic and climatic factors. Resin from five provenances was collected from southern Mexico. The percentage of rosin, turpentine and water was obtained, as well as the acidity and saponification index. P. oocarpa resin had 80.94 % rosin, 7.7 % turpentine and 11.49 % water. The saponification and acidity index was 125.47 and 117.49 mg KOH.g_1, respectively. All variables showed differences (p≤ 0.0001) between provenances. The provenance contributed between 6.44 and 11.71 % to the total variance, the error contributed between 88.29 and 93.56 %. Geographic and climatic variables only had an effect on the percentage of turpentine; the correlation was negative with altitude and longitude, but positive with temperature and precipitation. The results allow defining seed collection sites for resin plantations and orienting the selection for a P. oocarpa improvement program.

The anthropogenic deterioration of aquatic ecosystems affects water resources due to agricultural malpractices, pollution from domestic septic tanks, recreational activities, and poor watershed management, among others. This study examines the management of Las Curias Reservoir (176,974 m2), San Juan, Puerto Rico, post the 2016 arrival of the invasive aquatic fern Salvinia molesta. In December 2019, a community-led initiative introduced the Cyrtobagous salviniae weevil, an effective biological control agent for S. molesta, and commenced a mechanical removal campaign using an aquatic harvester. Limnological sampling (September 2019 to March 2022) and drone flights were employed to measure physicochemical and floating plant cover changes, respectively, in the reservoir. Monitoring of weevils in the reservoir demonstrated a rapid establishment and dispersal, which resulted in visible damage including browning of plants and eventually sinking of entire mats. By January 29, 2021, 71% (125,652 m2) of the reservoir surface was covered by salvinia. In 2022, the reservoir recorded an average dissolved oxygen concentration of 2.38 mg/L -1 (± 0.021, n = 144), the highest in the study period and indicative of ecosystem recovery. After three years of control efforts, dissolved oxygen, pH, and specific conductance returned to levels recorded prior to Salvinia molesta introduction. This ecosystem recovery, a first in Puerto Rico, could be attributed to an early use of mechanical control and a long-term impact of biological control.

This study aimed to evaluate the biological activities of two Allium species (Garlic and onion) as well as diallyl disulphide (DADS) and dipropyl disulphide (DPDS) as their representative bioactive compounds in a multi-assay experimental design. The genotoxic, antigenotoxic and lifespan effects of garlic, onion, DADS and DPDS were checked in Drosophila melanogaster and their cytotoxic, pro-apoptotic and DNA-clastogenic activities were analysed using HL60 tumoral cells. All compounds were non-genotoxic and antigenotoxic against H2O2-induced DNA damage with a positive dose-response effect and different inhibition percentages (the highest value: 95% for DADS) at all tested concentrations. Daily intake of Allium vegetables, DADS or DPDS had no positive effects on flies’ lifespan and healthspan. Garlic and DADS exerted the highest cytotoxic effects in a positive dose-dependent manner. Garlic and DADS exerted a DNA-internucleosomal fragmentation as an index of induced proapoptotic activity on HL60 cells. Allium vegetables and DADS were able to induce clastogenic strand breaks in the DNA of HL60 cells. This study showed the genomic safety of the assayed substances and their protective genetic effects against the hydrogen peroxide genotoxine. Long-term treatments during the whole life of Drosophila genetic model were beneficial only at low-median concentrations. The chemopreventive activity of garlic could be associated to its distinctive organosulphur DADS. We suggest that supplementary studies are needed to clarify the cell death pathway against garlic and DADS.

We review past and present results on the non-local form-factors of the effective action of semiclassical gravity in two and four dimensions computed by means of a covariant expansion of the heat kernel up to the second order in the curvatures. We discuss the importance of these form-factors in the construction of mass-dependent beta functions for the Newton's constant and the other gravitational couplings.

Knowing professionals’ attitudes is the basis for the development of skills for dealing with drug dependence. These attitudes may affect patients’ clinical safety and the cost-benefit ratio of the interventions. The goal of this study was to assess emergency and mental health nurses’ attitudes and perceptions towards alcoholics. A multicenter prospective descriptive study was conducted in six hospitals with 167 emergency and mental health nurses. Nurses classified alcoholics as sick individuals, although there was a tendency to feel comfortable working with them. Results indicated that these professionals had a rejecting attitude towards moderate alcohol consumption. We found a significant association between the attitude of the nurse and gender, with the degree of rejection towards the alcoholic being higher in men than in women and with less punitive attitudes in professionals from 0 to 11 years of professional experience.

Over the last decade, Psidium guajava L. (guava) leaves have demonstrated their in vitro and in vivo effect against Diabetes mellitus (DM). However, there is a lack of literature concerning the effect of the individual phenolic compounds present in the leaves in DM disease. For this reason, the aim of the present work was the in silico evaluation of each phenolic compound. The identification of an 80% ethanol extract of guava leaves revealed the presence of 73 compounds. The in silico study carried out with the DIA-DB web server revealed that aldose reductase was the target protein with heterogeneous affinity. Naringenin exhibited the highest number of interactions with target proteins, and compounds like catechin, quercetin, naringenin and morin displayed similarities with known antidiabetic drugs. In conclusion, the computational workflow showed that guava leaves contain several compounds that can play a therapeutic role in the treatment of DM.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

The mining wastes generated during the last decades in the mining region of Pachuca-Real del Monte in Mexico, still contains silver values of interest. For this reason, the present work is a preliminary study of the leaching kinetics of silver contained in these residues, using as a leaching reagent the thiosemicarbazide-oxygen system, with the aim of proposing this leaching system as a less toxic alternative than cyaniding process. Previous the leaching process, representative samples were wholly characterized, finding 56 g of Ag and 0.6 g of Au per ton. For the kinetic study in the mentioned system, were evaluated the reagent concentration, temperature, partial pressure of oxygen, pH and stirring rate. According the experimental results found, it was observed that [CH5N3S] concentration showed a significant effect on the leaching rate, obtaining a reaction order of n = 0.93, in the range of 20 - 40 mol CH5N3S ⋅ m-3, getting so a silver recovery up to 76.9%. The effect of temperature gave an activation energy of Ea = 45.55 KJ mol-1, which was indicative of a chemical reaction control. Finally, partial pressure of oxygen has a notable effect on leaching rate, but pH and stirring rate have not apparent effect.

The mining wastes generated during the last decades in the mining region of Pachuca-Real del Monte in Mexico, still contains silver values of interest. For this reason, the present work is a preliminary study of the leaching kinetics of silver contained in these residues, using as a leaching reagent the thiosemicarbazide-oxygen system, with the aim of proposing this leaching system as a less toxic alternative than cyaniding process. Previous the leaching process, representative samples were wholly characterized, finding 56 g of Ag and 0.6 g of Au per ton. For the kinetic study in the mentioned system, were evaluated the reagent concentration, temperature, partial pressure of oxygen, pH and stirring rate. According the experimental results found, it was observed that [CH₅N₃S] concentration showed a significant effect on the leaching rate, obtaining a reaction order of n = 0.93, in the range of 20 - 40 mol CH₅N₃S × m^-3, getting so a silver recovery up to 76.9%. The effect of temperature gave an activation energy of Ea = 45.55 KJ mol^-1, which was indicative of a chemical reaction control. Finally, partial pressure of oxygen has a notable effect on leaching rate, but pH and stirring rate have not apparent effect.

This paper describe the influence of the Rift Molango during the mineralization of elements of the platinum group and some light rare earths elements in a sedimentary exhalative ore deposit.

Gestational diabetes mellitus (GDM) is a hyperglycemia state that is typically diagnosed by an oral glucose tolerance test (OGTT), which is unpleasant, time-consuming, poorly reproducible, and tardy. The machine learning (ML) predictive models that have been proposed to improve GDM diagnosis are usually based on instrumental methods that take hours to get a result. Near-infrared (NIR) spectroscopy, a simple, fast and low-cost analytical technique has never been assessed for the prediction of GDM. This study aims to develop ML predictive models for GDM based on NIR spectroscopy, and to evaluate their potential as early detection or alternative screening tools according to their predictive power and time of analysis. Serum samples from the first (before GDM diagnosis) and the second (at the time of GDM diagnosis) trimester of pregnancy were analyzed by NIR spectroscopy. Four spectral ranges were considered, and 80 pretreatments were tested for each. NIR data-based models were built with single- and multi-block ML techniques. Every model was subjected to double cross-validation. The best first and second trimester models got areas under the receiver operating characteristic curve of 0.5768 ± 0.0635 and 0.8836 ± 0.0259, respectively. This is the first study reporting NIR spectroscopy-based methods for the prediction of GDM. The developed methods allow to predict GDM from 10 µL of serum in only 32 minutes. They are simple and fast, and have a great potential to be applied in clinical practice, especially as alternative screening tools to the OGTT at the time of GDM diagnosis.

Materials known as Nd:YAG are crystalline materials of the cubic system made from neodymium-doped yttrium aluminum garnet, which among others, have excellent optical properties. Nd:YAG four-level laser devices are highly used in both the health and industrial sectors. In this study, a simple and inexpensive alternative to manufacturing Nd:YAG materials through solid state reactions following powder processing routes was proposed. For this, an intense mixture of the precursor materials (Al2O3 and Y2O3) was carried out, followed by the addition of neodymium atoms to improve the optical properties of the resulting material. High energy mechanical mixing of the precursor powders resulted in submicron particles, with good size distributions of the powders. The advance of YAG formation was monitored by intermediate phase formation during heat treatment through interrupted tests at different temperatures and analysis by X-ray diffraction. From this analysis, it was found that reaction for the formation of the desired YAG is completed at 1500°C. Fourier-transform infrared spectroscopy analyses determined the presence of functional groups corresponding to the YAG. Finally, the study by optical emission spectroscopy showed wavelengths in agreement with the electronic structure of the elements of the synthesized Nd:YAG.

Contamination by microplastics (MP) in aquatic ecosystems is largely due to the release of millions of these particles from treated effluents from Wastewater Treatment Plants (WWTP). Due to the lack of policies and regulations that establish criteria for the control and elimination of MP from WWTP effluents, this research evaluated the presence of MP for particle sizes of 38 and 150 µm in influents and effluents from three WWTP in the port of Acapulco, Mexico. Using optical microscopy and Fourier transform infrared spectroscopy (FTIR) techniques, the MP detected were polyethylene (PE), polypropylene (PP), polyethylene terephthalate (PET) and polyvinyl chloride (PVC). MP removal efficiencies of 82.5 to 98.7% (38 µm) and 86.8 to 97.5% (150µm) were obtained; the MP average daily emissions to the receiving bodies of these three WWTPs were in the ranges of 9.5 x 106 - 4.70 x 108 particles and the annual emissions in the range of 3.05 x 109 - 1.72 x 1011 particles. This work reveals the urgency of implementing regulatory policies to avoid the continuous emission of MP to aquatic ecosystems from WWTPs in Acapulco, Mexico.

One of the interactions that has been studied in recent decades under the ecohydrological approach is infiltration, which is difficult to determine because the existing methods for estimation depends on certain variables that are difficult to establish or identify, and in other cases, the implementation of instrumentation is expensive. Given this, saturated hydraulic conductivity has been the descriptive variable of the infiltration process by recent authors, being understood as the conduction of water that occurs through the soil and its composition through the vegetation cover. The present design generated an easily accessible portable instrumentation model for the monitoring and collection of infiltration data in situ for basins and ecosystems with different land uses, in an automated manner with the objective of determining the vegetation patterns necessary to sustain the infiltration function. The INDI-INECOL tension infiltrometer [1] was chosen as the reference instrument. It evaluates the saturated hydraulic conductivity based on a column of water that descends through the system and it is exchanged in the soil by the air between the pores. To automate data collection, a measurement system has been proposed through a SCADA system, which is defined as a control, action, decision, storage and data recording system. This system collects field data from a sensor VL053L0X connected to a master station, in our case an Arduino board UNO, connected through the serial port and by a graphical user interface programmed on Python, to display, storage and enrichment of the sensor data and finally to be exported in files suitable for Microsoft Excel.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

This paper proposes a Case-Based Reasoning (CBR) system to contribute to reinforce the sustainable performance of an environmental management system. The CBR system aims to support the decision-making process to select environmental management actions aimed at reducing risky trends of the environmental state of a region. The CBR system takes advantage of a set of situation-solution pairs called cases, which are stored in a memory and then retrieved as candidates to solve new problems. Situations in this work are represented by a set of risky trends of the following key environmental variables: CO2 emissions, Air-Quality, Loss of Vegetation Cover, Water Availability, and Solid Waste, whose combination damage the environmental state quality of a region. Meanwhile, solutions are represented by a set of environmental management actions. Similar situations to a given current situation are retrieved from the memory of cases and then their solutions are combined, through an adaptation mechanism, until the solution of the current problem is obtained. We used risky trends derived from real data related to the environmental states of a Mexican region to test the proposed CBR system. The results obtained provided insights into the potential of CBR systems to support the decision-making process to select environmental management actions aimed at reducing risky trends of current environmental states.

High degree of polymerisation agave fructans (HDPAF) are presented as a novel encapsulating material. Electrospraying coating (EC) was selected as the encapsulation technique and β-carotene as the model bioactive compound. In case of direct electrospraying, two encapsulation methodologies (solution and emulsion) were proposed to find the formulation which provided a suitable particle morphology and an adequate concentration of β-carotene encapsulated in the particles. SEM images showed spherical particles with sizes ranging from 440 to 880 nm depending on the concentration of HDPAF and processing parameters. FTIR analysis confirmed interaction and encapsulation of β-carotene with HDPAF. Thermal stability of β-carotene encapsulated in HDPAF was evidenced by thermogravimetric analysis (TGA). The study showed that β-carotene encapsulated in HDPAF by the EC method remained stable for up to 50 h of exposure to UV light. Therefore, HDPAF is a viable option to formulate nanocapsules as a new encapsulating material. In addition, EC allowed increasing the ratio β-carotene:polymer as well as its photostability.

Background: Atopic dermatitis is a chronic condition that significantly affects the daily life of those who suffer from it, requiring complex and personalized management with active participation of the patient in the management of their disease. Objective: to describe the design and development process of a mobile application, using the Design Thinking method, for the follow-up of patients with atopic dermatitis. Methods: User-centered design and prototype creation method, differentiating the phases of the empathize, define, idea, prototype, and test. A purposive snowball sampling was used to recruit patients with atopic dermatitis, family members, and health professionals. Three two-hour workshops were held, attended by 25 people. Results: the parameters to be monitored will include objective data (physical, behavioral, treatments, environmental, integration of daily routines) and subjective data (user experience). On the other hand, it will figure out behavior patterns, set up rewards, foster a feeling of community, and use notifications and a chatbot. Conclusion: The active integration of all stakeholders at each stage of the design and development of the digital solution has improved its relevance and acceptance, resulting in a tool that is expected to significantly improve the management of atopic dermatitis.

A mathematical model, composed of two non-linear differential equations that describe the population dynamics of CD4 T cells in the human immune system, as well as viral HIV particles, is proposed. The invariance region is determined, classical equilibria stability analysis is performed using the basic reproduction number, and numerical simulations are carried out, in order to illustrate stability results. Later, the model is modified with a delay term, which describes the time that cells require for immunological activation. This generates a two-dimensional integro-differential system, which is transformed into a system with three ordinary differential equations, via auxiliary variable use. For the new model, equilibrium points are determined, their local stability is examined, and results are studied by way of numerical simulation.

This study was carried out with a low-cost electronic nose prototype based on eight metal oxide sensors (MQ) in order to characterize samples of lemons treated with 0.5% and 0.1% of sodium benzoate. The MQ sensors designed are sensitive to one or more chemicals to detect the presence of a variety of chemicals in the air. The sensor MQ135 detects ammonia, hydrogen sulphide and benzene. Signal data were studied to obtain a pattern recognition of rotten in lemon fruits. Network analysis was used to obtain a calibration of measures among the stage of lemons. In this article, an electronic nose prototype based on 8 MQ metal oxide sensors has been used in order to analyze and characterize different lemon varieties to which different chemical treatments have been applied in pre-harvest. PCA-based data analyzes were used to observe clusters in the data. Through the combined use of the data obtained by the nose and these Sequential Neural Networks (SNNs) a classification tool for lemon varieties and applied treatments has been obtained. It is shown the ability of this device to be used as a reliable discrimination method, in addition to providing low cost and optimization of time and expert resources.

Right atrial isomerism (RAI) is a complex entity whose treatment and outcome are heterogeneous. The aim of this study was to analyze the results obtained after cardiac surgery in patients with RAI. A retrospective study was conducted; it included patients diagnosed with RAI who underwent cardiac surgery; their follow-up was from January 1, 2010 to March 31, 2020. Demographic characteristics and perioperative conditions were described. Thirty-eight patients with RAI were included, the median age was 4 years (IQR 2-9.2), and 57.9% were men. The main diagnoses were atrioventricular canal (63.2%) and pulmonary stenosis (55.3%). The most common surgical procedures were modified Blalock‐Taussig shunt (65.8%) and total cavopulmonary connection with an extracardiac conduit fenestrated without cardiopulmonary bypass (15.9%). The use of inhaled nitric oxide was a marker of postoperative mortality in critically ill patients (OR: 10.33; 95% CI: 1.04 - 102.08; p = 0.02). The overall survival was 86.8%, with a better outcome in those who did not require reintubation (Log Rank, p < 0.01). The survival of RAI was similar to other centers of reference. Individuals with RAI should be evaluated rigorously to determine an adequate repair strategy, considering high morbidity and mortality.

Seeds can maintain their quality for a limited time; after that, they will lose their germination ability and vigor. Some physiological and physicochemical changes in the structure of the seeds during storage can decrease the quality of the seeds which is known as aging. Therefore, detection of the strong young seeds from the old ones is a vital issue in the modern agriculture. Conventional methods of detection of the seed viability and germination are destructive, time-consuming and costly. In this research, two peanut cultivars, namely North Carolina 2 (NC-2) and Florispan were selected and three artificial aging levels were induced to them. Hyperspectral images (HSI) of the samples were acquired and the seed viability was evaluated using two pre-trained convolutional neural network (CNN) image processing models, AlexNet and VGGNet. The noise of the reflection spectra of the samples was relatively resolved and modified by combining Preprocessing techniques of moving average (MA) and standard normal variate (SNV). Using principal component analysis (PCA), the dimensions were declined and three principal components (PC) were extracted. These PCs were then used as variables in the classification of support vector machine (SVM) and linear discriminant analysis (LDA). The results showed the high capability of CNN architectures such as AlexNet and VGGNet in detection of the seed viability based on the HIS with no pre-processing and feature extraction. The mentioned architectures reached the accuracy of 0.985 and 0.986, respectively. The combination of feature extraction method of PCA with LDA and SVM classifiers showed that the use of a limited number of PCs instead of all wavelengths can decrease the complexity of modeling, while enhancing the efficiency of the models such that LDA and SVM classifiers achieved the accuracy of 0.983 and 0.986 in classification of peanut sees, respectively.

This paper proposes an optimal trading algorithm based on a novel application of the conventional Control Engineering (CE). We consider a fundamental CE concept, namely, the feedback control and apply it to the Algorithmic Trading (AT). The concrete feedback control strategy is designed in a form of the celebrated Proportional-Integral-Derivative (PID) model. The highly fluctuating nature of the modern financial markets has led to the adoption of a model-free realisation of the generic PID framework. The control theoretical methodology we propose is combined with the advanced statistics for the historical market data. We obtain a specific log-normal probability distribution function (pdf) associated with the specific quantities associated with the available stock data. The empirical log-normal pdf mentioned above makes it possible the necessary PID gains optimization. For this aim, we apply the data-driven optimization approaches and consider the corresponding Monte Carlo solution procedure. The optimized PID trading algorithm we propose is also studied in the Fourier analysis framework. This equivalent frequency domain representation involves a new concept in the financial engineering, namely, the "stock market energy" concept. For the evaluation, we implement the proposed PID optimal trading algorithm and develop a Python based prototype software. We finally apply the corresponding prototype software to a dataset from the Binance BTC / USDT stock market. The experimental result illustrates the implementability of the proposed optimal PID trading scheme and also shows the effectiveness of the proposed CE methods in the modern AT.

Computer vision is a powerful technology that has enabled solutions in various fields by analyzing visual attributes in images. One field that has taken advantage of computer vision is agricultural automation, which promotes high-quality crop production. The nutritional status of a crop is a crucial factor in determining its productivity. This status is mediated by approximately 14 chemical elements acquired by the plant, and their determination plays a pivotal role in farm management. To address the timely identification of nutritional disorders, this study focuses on the classification of three levels of phosphorus deficiencies through individual leaf analysis. The methodological steps include: (1) generating a database with laboratory-grown maize plants that were induced to total phosphorus deficiency, medium deficiency, and total nutrition, using different capture devices; (2) processing the images with state-of-the-art transfer learning architectures (i.e. VGG16, ResNet50, GoogLeNet, DenseNet201, and MobileNetV2); and (3) evaluating the classification performance of the models using the created database. The results show that the VGG16 model achieves superior performance, with 98% classification accuracy. However, the other studied architectures also demonstrate competitive performance and are considered state-of-the-art automatic leaf deficiency detection tools. The proposed method can be a starting point to fine-tune machine vision-based solutions tailored for real-time monitoring of crop nutritional status.

Making sustainable business models, especially in manufacturing, is a key approach for organizations to adopt in order to create more sustainable processes. New technologies are needed to implement new policies that can minimize the economic, environmental, and social consequences of industrial activity. Sustainable maintenance is decisive to guarantee the availability, reliability, and safety of assets, surpassing traditional maintenance policies and embracing the principles of the circular economy. The main objective of Maintenance 4.0 is to increase the lifespan and availability of the equipment by preventing unplanned downtime, reducing planned shutdowns, and improving safety. This research focuses on the integration of advanced Industry 4.0 tools with conventional monitoring and control techniques in process industries. The article suggests that while complex neural networks might provide good predictions, simpler solutions can generalize well and have lower prediction errors because they can capture the underlying relationships between variables in a specific asset better. The combination of maintenance function, Industry 4.0 tools, and advanced statistical solutions to obtain sustainable processes can facilitate organizational change and aid decision-making in equipment management. These solutions seek to reduce interruptions and expenses through the unnecessary utilization of labor and spare parts. All these considerations improve communication and data processing, resulting in improved maintenance of a hydrogen compressor in the petrochemical industry.

The aim of this review is to present the Quality by Design (QbD) model as a suitable methodology to perform research in the academic Costa Rican institutions that teach Pharmacy. Pubmed, Science Direct, and Google Scholar databases were screened for original and review papers, as well as short communications published not more than 10 years ago. Publications were screened by title and abstract. Relevant references were used to develop three important themes: The University’s Research Model in Costa Rica, QbD Model, and QbD as a Research Methodology for Industrial Pharmacy in the Academy. In this sense, the QbD model is a great methodology for carrying out research projects regarding Pharmaceutical Sciences but especially for Drug Development. Academic research based on this model enables training and developing practical, scientific, and leadership skills in pharmacy students. The generated knowledge can be shared in the classrooms, which represents an ideal environment to communicate their research results and to foster collaborative work between researchers, professors, and students. The participation of all these actors allows a high level of commitment to research work, which benefits the scientific advancement of the university and society. It is important to visualize the student body as potential key actors in the research process, encouraging in them the desire to become trained scientific researchers who want to pursue a career in the academy, giving continuity to it.

This work shows the preliminary description of the origin of a sedimentary - exhalative outcrop of Jurassic Lower Pliensbachian. The location of this deposit was achieved by applying an examination based in the identification of sedimentary transgressions of heterochronies ages and the identification of a Rift – type mega –structure. According with the methodology, it was carried out a study of the discordant relationships between two types of sediments: continental and marine. According the characterization, it was noted the existence of light rare earths, in values that show positive anomalies in comparison with the distribution of elements in upper continental crust according to the Clarke [1], reflecting so a felsic affinity of the mineral deposit. Also, positive anomalies of platinum and Pd, were determined with marginal contents of Au and Ag; and finally the base metals Zn, Pb and Cu were detected in low contents, which could be due to the presence of altered shale. According to the sedimentary lithology found, which was of siliciclastic type; to the exhalative roots observed during the fieldwork; the presence of quartz minerals such as biotite and muscovite; the presence of minerals of hydrothermal remobilization like chalcopyrite with some base metals, altered shale, as well as sulfur deficiency; this mineral reservoir could be defined as a SEDEX – type.

The Stirling engine is a simple type of external-combustion engine with an external combustion engine based on cyclic compression and expansion of gas at different temperature levels. It has high efficiency; low vibration levels, simple structure and can run on any combustible fuels. It has been the object of numerous studies. This paper presents an analysis of a Stirling engine model GENOA 03 for electric power generation, of 3 KW of nominal power with pressurized air as working fluid, currently under development. To improve its performance and ensure a good operational reliability, it is necessary to carry out a modelling of the engine in all its operating range. This requires complex numerical models that simulate the behaviour of any element of the engine in a cycle. Two typologies of thermodynamic models are developed in this work: isothermal and adiabatic. The main benefits and shortcomings of each model are mentioned. The geometry and conditions of the engine have been adapted through the Matlab ® tool, in order to obtain the operative conditions of the cooler that you want to replace, as well as an approximation to the expected behaviour.

Testing and isolation have been crucial for controlling the COVID-19 pandemic. Venezuela has one of the weakest testing infrastructures in Latin America and the low number of reported cases in the country has been attributed to substantial underreporting. However, the Venezuelan epidemic seems to have lagged behind other countries in the region, with most cases occurring within the capital region and four border states. Here, we describe the spatial epidemiology of COVID-19 in Venezuela and its relation to population mobility, migration patterns, non-pharmaceutical interventions and fuel availability. Using an SEI metapopulation model, we explore how movement patterns could have driven the observed distribution of cases. Low within-country connectivity most likely delayed the epidemic in most states, except for those bordering Colombia and Brazil where high immigration seeded outbreaks. NPIs slowed early epidemic growth and subsequent fuel shortages appeared to be responsible for limiting the spread of COVID-19 across the country.

The Attentional Networks Test for Interactions and Vigilance–executive and arousal components (ANTI-Vea) is a computerized task of 32 min duration in the standard format. The task simultaneously assesses the main effects and interactions of the three attentional networks (i.e., phasic alertness, orienting, and executive control) and two dissociated components of vigilance with reasonable reliability (executive and arousal vigilance). We present this free and publicly accessible resource (ANTI-Vea-UGR; https://anti-vea.ugr.es/) developed to easily run, collect, and analyze data with the ANTI-Vea (or its subtasks measuring some attentional and/or vigilance components embedded in the ANTI-Vea). Available in six different languages, the platform allows for adaptation of stimuli timing and procedure to facilitate data collection from different populations (e.g., clinical patients, children). Collected data can be freely downloaded and easily analyzed with the provided scripts and tools, including a Shiny app. We discuss previous evidence supporting that attention and vigilance components can be assessed in typical lab conditions as well as online and outside the laboratory. We hope this tutorial will help researchers interested in measuring attention and vigilance with a tool useful to collect data from large sample sizes and easy to use in applied contexts.

Salmonella spp. contaminates egg and poultry meat leading to foodborne infections in humans. The emergence of antimicrobial-resistant strains limit the use of antimicrobials. We aimed to determine the effects of the food supplement, fermented defatted ‘alperujo’, a modified olive-oil by-product, on Salmonella Typhimurium colonisation in broilers. One hundred and twenty 1-day-old broilers were divided into four experimental groups: 2 control groups and 2 treated groups, and challenged with S. Typhimurium at day 7 or 21. On days 7, 14, 21, 28, 35 and 42 of life, duodenum and caecum tissue samples were collected for histopathological and histomorphometric studies. Additionally, cecum content was collected for Salmonella spp. detection by culture and qPCR, and for metagenomic analysis. Our results showed a significant reduction of Salmonella spp. in the cecum of 42-day-old broilers, suggesting that fermented defatted ‘alperujo’ stimulates Salmonella Typhimurium clearance in that cecum and may contribute to diminishing the risk of carcass contamination at the time of slaughter. Additionally, the improvement of the mucosal integrity suggests that enhancing intestinal health helps to limit Salmonella spp. colonisation in the host, mitigating production losses. These results could provide evidence that FDA would contribute to prophylactic and therapeutic measures to reduce salmonellosis prevalence in poultry farms.

Tumors of the central nervous system produce adverse outcomes in everyday life; however, low-grade gliomas are uncommon in adults. For this reason, the objective is to describe the executive function of a 59-year-old adult neuro-oncological patient. Pre- and postintervention evaluation of neurological and neuropsychological functioning was performed through neuroimaging techniques (iRM, Spectroscopy, Electroencephalography), hospital history, psychological interview, and Wisconsin Card Classification Test (WCST). Executive performance exhibited a noticeable decline in typical and centile WCST results, as evidenced by deterioration in persistent scores, failure to maintain an attitude and difficulty learning from clinical samples. This information coincides with the evolution of the neuroimage over time. Finally, this topic is discussed in the literature.

Peanuts, owing to their composition of complex carbohydrates, plant protein, unsaturated fatty acids, and essential minerals (magnesium, iron, zinc, and potassium), hold significant potential as a vital component of the human diet. Additionally, their low water requirements and nitrogen fixation capacity make them an appropriate choice for cultivation in adverse environmental conditions. The germination ability of seeds profoundly impacts the final yield of the crop, assessing seed viability of extreme importance. Conventional methods for assessing seed viability and germination are both time-consuming and costly. To address these challenges, this study investigated Visible-Near Infrared Spectroscopy (Vis/NIR) in the wavelength range of 500-1030 nm as a non-destructive and rapid method to determine the viability of two varieties of peanut seeds: North Carolina-2 (NC-2) and Spanish flower (Florispan). The study subjected the seeds to three levels of artificial aging through heat treatment, involving incubation in a controlled environment at a relative humidity of 85% and a temperature of 50°C over 24-hour intervals. The absorbance spectra noise was significantly mitigated and corrected to a large extent by combining the Savitzky-Golay (SG) and Multiplicative Scatter Correction (MSC) methods. To identify the optimal wavelengths for seed viability assessment, a range of meta-heuristic algorithms were employed, including world competitive contest (WCC), league championship algorithm (LCA), Genetics (GA), Particle Swarm Optimization (PSO), Ant Colony Optimization (ACO), imperialist competitive algorithm (ICA), learning automata (LA), heat transfer optimization (HTS), forest optimization (FOA), discrete symbiotic organisms search (DSOS), and cuckoo optimization (CUK). These algorithms offer powerful optimization capabilities for effectively extracting relevant wavelength information from spectral data. Results revealed that all the algorithms demonstrated remarkable accuracy in predicting the allometric coefficient of seeds, achieving correlation coefficients exceeding 0.985 and errors below 0.0036, respectively. In terms of execution time, the ICA (2.3635 seconds) and LCA (44.9389 seconds) algorithms exhibited the most and least efficient performance, respectively. Conversely, the FOA and the LCA algorithms excelled in identifying the least number of optimal wavelengths (10 wavelengths). Subsequently, the seeds were classified based on the wavelengths selected by the FOA (10 wavelengths) and (DSOS (16 wavelengths) methods, in conjunction with logistic regression (LR), decision tree (DT), Multilayer Perceptron (MP), support vector machine (SVM), k-nearest neighbor (K-NN), and NaiveBayes (NB) classifiers. The DSOS-DT and FOA-MP methods demonstrated the highest accuracy, yielding values of 0.993 and 0.983, respectively. Conversely, the DSOS-LR and DSOS-KNN methods obtained the lowest accuracy, with values of 0.958 and 0.961, respectively. Overall, our findings demonstrated that Vis/NIR spectroscopy, coupled with variable selection algorithms and learning methods, presents a suitable and non-destructive approach for detecting seed viability.

This paper presents a novel micro-segmented genetic algorithm (μsGA) to identify the best solution for the locomotion of a quadruped robot designed on a rectangular ABS plastic platform. We compare our algorithm with three similar algorithms found in the specialized literature: a standard genetic algorithm (GA), a micro-genetic algorithm (μGA), and a micro artificial immune system (μAIS). The quadruped robot prototype guarantees the same conditions for each test. The platform was developed using 3D printing for the structure and can accommodate the mechanisms, sensors, servomechanisms as actuators. It also has an internal battery and a multicore embedded system (mES) to process and control the robot locomotion. This research proposes a μsGA that segments the individual into specific bytes. μGA techniques are applied to each segment to reduce the processing time; the same benefits as the GA are obtained, while the use of a computer and the high computational resources characteristic of the GA are avoided. This is the reason why some research in robot locomotion is limited to simulation. The results show that the performance of μsGA is better than the three other algorithms (GA, μGA and AIS). The processing time was reduced using a mES architecture that enables parallel processing, meaning that the requirements for resources and memory were reduced. This research solves the problem of continuous locomotion of a quadruped robot, and gives a feasible solution with real performance parameters using a μsGA bio-micro algorithm and a mES architecture.

Building roofs are sources of unwanted heat for buildings situated in zones with a warm climate. Thus, reflective coatings have emerged as an alternative to reject a significant fraction of solar energy received by roofs. In this research, the thermal behavior of concrete slab-type roofs with traditional and solar reflective coatings was simulated using a computational tool. Weather data from four cities in Mexico with a warm climate were used as boundary conditions. This tool is an in-house code based on the Finite Volume Method developed by the author to perform building components simulations. The code was validated with experimental data from previous work. A series of comparative simulations were developed, taking a gray roof as a control case. The results showed that for the roof without thermal insulation (single roof), the solar reflective coatings reduced the exterior surface between 11 and 16∘C. Consequently, the single roofs’ daily heat gain was reduced by a factor ranging between 41 and 54%. On the other hand, for the insulated roof, the reflective coatings reduced the exterior surface temperature between 17 and 21∘C. At the same time, the daily heat gain of composite roofs was reduced between 37 and 56%.

Back-care knowledge and behaviour may play a vital role in preventing musculoskeletal current and future discomfort and injuries. The aim of the current survey was to explore the level of knowledge regarding ergonomics and posture together with postural behaviour and the incidence of musculoskeletal pain (MSP) in university students in the northeast of England. A mixed methods survey was conducted on a convenience sample of 55 university students. The 32-item valid and reliable questionnaire contains questions on socio-demographics, MSP, knowledge regarding ergonomics and posture (8 closed ended and 8 open-ended items) as well as postural behaviour. Nearly 1.8%, 20% and 78.2% of the university students had poor, fair and good knowledge of ergonomics and posture respectively. Among the 37 students who carried a backpack, 51.4% were found to have poor postural behaviour, 37.8% had fair behaviour and 10.8% had good postural behaviour. Of the 18 students who did not carry a backpack, 55.6% were found to have poor postural behaviour, 27.8% had fair behaviour and 16.6% had good postural behaviour. 70.9% of the students experienced MSP with the most prevalent site of pain being the lower back region. The key themes that emerged from qualitative data (8 open-ended questions) were: “Comfortable posture”, “Correct spinal alignment”, “Spine support”, “less pain and injuries”, “Use knees not the back”, “Keep the object close to body”, “Hands on desk”, “Feet flat on floor” as well as “eyes at screen level”. The findings of this study can be used to develop targeted interventions aimed at educating university students about ergonomics and posture in order to prevent the incidence of MSP. Future research in this field with a large and more representative sample of the university students’ population is strongly recommended to fully understand their knowledge of ergonomics and posture, postural behaviour as well as incidence of MSP.

Several sun models suggest the radioactive balance where the concentration of greenhouse gases and the albedo effect are related to the Earth's surface temperature. There is a considerable increment of greenhouse gases due to anthropogenic activities. Climate change correlates with this alteration in the atmosphere and an increase in surface temperature. Efficient forecasting of climate change and its impacts of 1.5°C global warming above pre-industrial levels could be helpful to respond to the threat of c.c. and develop sustainably. Many studies have predicted the temperature change in the coming years. The global community has to create a model that can realize good predictions to ensure the best way to deal with the warming. Thus, we propose a finite-time thermodynamic (FTT) approach in the present work. The FTT can solve problems such as the faint young sun paradox. In addition, we use different machine learning models to evaluate our method and compare the experimental prediction and results.

Atrophy quantification is fundamental for understanding brain development and diagnosing and monitoring brain diseases. FSL-SIENA is a well-known fully-automated method that has been widely used in brain magnetic resonance imaging studies. However, intensity variations arising during image acquisition that may compromise evaluation, analysis and even diagnosis. In this work, we study whether intensity standardisation can improve longitudinal atrophy quantification. We considered seven methods comprising z-score, fuzzy c-means, Gaussian mixture model, kernel density, histogram matching, white stripe, and removal of artificial voxel effects by linear regression (RAVEL). We used a total of 330 scans from two publicly-available datasets, ADNI and OASIS. In scan-rescan assessments, that measures robustness to subtle imaging variations, intensity standardisation did not compromise the robustness of FSL-SIENA significantly (p>0.1). In power analysis assessments, that measures the ability to discern between two groups of subjects, three methods led to consistent improvements in both datasets with respect to the original: fuzzy c-means, Gaussian mixture model, and kernel density estimation. Reduction in sample size using these three methods ranged from 17% to 95%. The performance of the other four methods was affected by spatial normalisation, skull stripping errors, presence of periventricular white matter hyperintensities, or tissue proportion variations over time. Our work evinces the relevance of appropriate intensity standardisation in longitudinal cerebral atrophy assessments using FSL-SIENA.

Abstract: Rhizobia are soil proteobacteria able to engage in a nitrogen-fixing symbiotic interaction with legumes which involves root rhizobial infection and bacterial invasion of new organs formed by the plant in response to the presence of appropriate bacterial partners. This interaction relies on a complex molecular dialogue between both symbionts. Bacterial N-acetyl-glucosamine oligomers called Nod factors are indispensable in most cases for early steps of the symbiotic interaction. In addition, different rhizobial surface polysaccharides, such as exopolysaccharides (EPS), may also be symbiotically relevant. EPS are acidic polysaccharides located out of the cell with little or no cell association that carry out important roles both in free-life and in symbiosis. EPS production is very complexly modulated and, frequently, co-regulated with that of Nod factors, but the type of co-regulation varies depending on the rhizobial strain. Many studies point out a signalling role of EPS-derived oligosaccharides in root infection and nodule invasion but, in certain symbiotic couples, EPS can be dispensable for a successful interaction. In summary, the complex regulation of the production of rhizobial EPS varies in different rhizobia and the relevance of this polysaccharide in symbiosis with legumes depends on the specific interacting couple.

Introduction: Coronaviruses are zoonotic viruses that include human epidemic pathogens such as the Middle East Respiratory Syndrome virus (MERS-CoV), and the Severe Acute Respiratory Syndrome virus (SARS-CoV), among others (e.g., COVID-19, the recently emerging coronavirus disease). The role of animals as potential reservoirs for such pathogens remains an unanswered question. No systematic reviews have been published on this topic to date. Methods: We performed a systematic literature review with meta-analysis, using three databases to assess MERS-CoV and SARS-CoV infection in animals and its diagnosis by serological and molecular tests. We performed a random-effects model meta-analysis to calculate the pooled prevalence and 95% confidence interval (95%CI). Results: 6,493articles were retrieved (1960-2019). After screening by abstract/title, 50 articles were selected for full-text assessment. Of them, 42 were finally included for qualitative and quantitative analyses. From a total of 34 studies (n=20,896 animals), the pool prevalence by RT-PCR for MERS-CoV was 7.2% (95%CI 5.6-8.7%), with 97.3% occurring in camels, in which pool prevalence was 10.3% (95%CI 8.3-12.3). Qatar was the country with the highest MERS-CoV RT-PCR pool prevalence, 32.6% (95%CI 4.8-60.4%). From 5 studies and 2,618 animals, for SARS-CoV, the RT-PCR pool prevalence was 2.3% (95%CI 1.3-3.3). Of those, 38.35% were reported on bats, in which the pool prevalence was 14.1% (95%CI0.0-44.6%). Discussion: A considerable proportion of infected animals tested positive, particularly by nucleic acid amplification tests (NAAT). This essential condition highlights the relevance of individual animals as reservoirs of MERS-CoV and SARS-CoV. In this meta-analysis, camels and bats were found to be positive by RT-PCR in over 10% of the cases for both; thus, suggesting their relevance in the maintenance of wild zoonotic transmission.

This article analyses the environmental impact of the measures imposed during the SARS-CoV-2 pandemic. We compare the evolution of atmospheric pollution levels in recent years and during lockdown, and assess the effects of the decrease in mobility and changes in patterns and lifestyles during the latter period. Thus, the reduction in the risk to human health brought about by the improvement of air quality during the months of confinement through the use of dose-response functions is estimated. The focus of the case study is the island of Tenerife. The island of Tenerife has been selected because it can serve as an example for other sites in Europe. We distinguish between the three areas with the highest population concentrations: the Metropolitan, Southern, and Northern areas. The impacts of air pollution and its relationship with changes in consumption and activity patterns are clearly distinguishable. Therefore, the lessons learned can be easily extrapolated to other areas, in both island and mainland contexts.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

Family Parvoviridae consists of small, non-enveloped viruses with linear, single-stranded DNA genomes of approximately 4-6 kilobases, subdivided into 3 subfamilies: Parvovirinae, Densovirinae and Hamaparvovirinae. Parvoviruses of aquatic animals infect crustaceans, mollusks, and finfish. In this review, these parvoviruses, which are highly host-specific and are associated with mass morbidity and mortality in both farmed and wild aquatic animals are described. They include Cherax quadricarinatus densovirus (CqDV) in freshwater crayfish; Sea star-associated densovirus (SSaDV) in sunflower sea star on the Northeastern Pacific Coast; Clinch densovirus 1 in freshwater mussels in the Clinch River, Virginia, and Tennessee, USA, in subfamily Densovirinae; Hepatopancreatic parvovirus (HPV) and Infectious hypodermal and hematopoietic necrosis virus (IHHNV) in farmed shrimp worldwide; Syngnathid ichthamaparvovirus 1 in gulf pipefish in the Gulf of Mexico and parts of South America; and Tilapia parvovirus (TiPV) in farmed tilapia in China and Thailand, in the subfamily Hamaparvovirinae. In addition, virus megataxonomy has enabled the inclusion of novel parvoviruses detected in both diseased and healthy animals using metagenomic sequencing for virus discovery, such as the novel zander parvovirus from zander in Hungary, novel salmon parvovirus from sockeye salmon smolts in British Columbia-Canada, and Spawner-isolated mortality virus (SMV) from shrimp broodstock in Australia.

Currently, agro-industrial residues have been used to obtain bioactive compounds. The fermentation process is an alternative for the use of these residues and to be able to accumulate metabolites that may be of interest to different industrial sectors. The aim of this study was to evaluate solid-state fermentation conditions using pineapple waste as substrate with Aspergillus niger spp., to release polyphenolic compounds using a Plackett-Burman exploratory design. Temperature, humidity, inoculum, NaNO3, MgSO4, KCl and KH2PO4 conditions in the fermentation process were evaluated. The results revealed that the Aspergillus niger HT3 strain reached a hydrolyzable tannins accumulation of 10.00 mg/g, while Aspergillus niger Aa20 reached a condensed tannins release of 82.59 mg/g. The KH2PO4 affect the release of condensed tannins with A. niger Aa20 and MgSO4 affect the release of hydrolyzable tannins with A. niger HT3. In addition, a positive antioxidant activity was demonstrated for the DPPH, ABTS and FRAP technique. The HPLC analysis was able to identify compounds in the fermented pineapple peel such as 3-feruloylquinic acid, caffeic acid, lariciresinol and 3-hydroxyphloretin 2'-O-xylosyl-glucoside, among others. The solid-state fermentation process is a biotechnological alternative for the release of bioactive compounds.

The aim of this work was to classify the business incubators in Spain according to the four phases of the startup’s incubation process. Considering that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the business incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis has been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors. Finally, the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3, named activity monitoring and control, was related to phase 3 or basic incubation variables. Cluster analysis facilitates the grouping of business incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small sized business incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factors 1 and 2. Factor 3, although positive, it is susceptible to improvement. They are the largest group of business incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

Our paper deals with an advanced statistical tool for the volatility prediction problem in financial (crypto) markets. Firstly, we consider the conventional GARCH involved volatility models. We next extend the corresponding GARCH based forecasting and calculate a specific probability associated with the predicted volatility levels. Since the probability evaluation is based on a stochastic model, we next develop an additional data-driven estimation of this probability. The proposed advanced statistical estimation uses real (historical) market data. The obtained theoretic results for the statistical probability of levels are also discussed in the framework of the integrated volatility concept. A possible application of the established probability estimation to the volatility clustering problem is also mentioned. Our paper includes a concrete practical implementation of the resulting (combined) volatility prediction tool and considers a novel module for trading and volatility estimation in crypto markets recently developed by 1ex Trading Board group in collaboration with the GoldenGate Venture. Moreover, we discuss shortly a possible using of the proposed model based and data-driven volatility prediction methodology in the financial risk management.

Currently, the textile industry is a poorly automated sector, due in part to problems in the handling of deformable leather and textile parts during production operations. In this work, several problems in the handling process of leather and textile parts are addressed, introducing methods to increase the automation of the process. A pneumatic actuator designed to pick up textile or leather parts avoiding their deformation during transport has been developed. This actuator maximizes the number of gripping points to improve handling, making it more stable and efficient. Additionally, a vision system has been implemented in the part picking task which, in conjunction with the CAD information of the part, sends the modified gripping position of the part to the robot. This allows customized handling of each textile or leather part. Finally, validation tests have been carried out on this development, both in simulations and in laboratory conditions, demonstrating its viability and direct applicability in the production line.