Abstract: Molybdenum (Mo) thin films were sputtered from two kinds of Mo targets with different microstructures under the same sputtering process, and the effect of microstructure of Mo target on morphology, deposition rate and resistance of sputtered film were studied and discussed. The results show that morphological differences between Mo thin films sputtered by Mo targets with different microstructures are very small. The more uniform and finer the grain structures of Mo target, the better the uniformity on thickness and resistance of Mo sputtered film. Moreover, during sputtering process, when Mo target’s grain size is finer and the surface area of grain boundary is higher, the thickness reduction of the target is more homogeneous and the sputtering film has faster deposition velocity. The difference in microstructure of the Mo target has not obvious influence on the grain orientation of sputtering film.

Greenwater (splashing of water on the deck) loading is a classical problem faced by the designer of ship-shaped vessels, which becomes even worst when the vessel operates at harsh weather conditions for an extended period. Installation of breakwaters on the deck can play a crucial role in minimizing this impact. However, research on the design and optimization of the breakwater is still at its infancy, and this study aims at shedding further light on this area by proposing and analyzing the effectiveness of three breakwater designs on a fixed box-shaped vessel. Commercial CFD software is used for this investigation. However, the design model (without breakwater) was validated at first against experimental results of green water splashing, before performing the actual simulations with proposed breakwater design. A vertical plate is used as the deck structure, and greenwater pressure at several locations on that plate is measured to compare the effectiveness of various breakwater designs. Overall, breakwaters with openings (perforations, grillages etc.) found to be more effective in minimizing the pressure generated by the greenwater. Nevertheless, there are significant rooms for improvement on breakwater designs, and some topics for further research are also suggested in this regard.

Evaluating soil quality across various altitudinal gradients, both with and without vegetative cover, is crucial for the proper functioning of soil and optimal crop growth, thereby contributing to the sustainability of agroecosystems. Although the altitudinal gradient significantly influences soil quality, the ability to predict this quality, expressed through an index, in soils with and without vegetative cover, is still insufficiently explored. This study aimed to assess soil quality in the Jun Jun micro-watershed, located in the Tungurahua region, Ecuador. To achieve this objective, three categories of altitudinal gradients were selected: less than 2800 meters above sea level (masl), between 2800 and 2900 masl, and greater than 2900 masl. A total of 24 soil samples were collected in the mentioned gradients, considering both areas with and without vegetative cover. The indicators used included chemical and biological parameters such as soil organic carbon (OC), earthworm density (WD), earthworm biomass (WB), organic matter (OM), pH, total nitrogen (TN), and organic carbon (OC). The results revealed that in areas with altitudinal gradients below 2800 masl, soil quality index values were higher compared to other altitudes. In vegetated areas, a decrease in index values was observed as the altitudinal gradient increased, indicating a deterioration in soil quality with altitude. These findings are significant in providing a quantitative assessment of the effects of altitudinal gradient and vegetative cover influence on soil quality.

A Shape Memory Alloy (SMA) enabled Overtopping Wave Energy Converter (OWEC) that maximizes its overtopping discharge, and thus energy output under different wave conditions is presented. Among all the parameters affecting the overtopping discharge rate, the crest freeboard height is the most influential one to control the overtopping discharge rate and the stored overtopping volume behind it. Currently, all the OWEC crest freeboard heights are fixed by design to maximize the discharge rate on one particular sea state. In the present study, we show that the SMA can adjust the crest freeboard height through a control system based on the sea state and achieve an optimal overtopping discharge rate. A scaled OWEC model is built in the lab with its crest freeboard height controlled by springs made of SMA. The length (and thus tension) of the springs is controlled by temperature changes by changing the passing current through the springs. By adjusting the length of the springs based on the incoming wave condition, we adjust the freeboard to an optimal height known to generate a maximum overtopping discharge rate for energy conversion. This smart material-enabled design can maximize the overtopping discharge and thus the output power of the OWEC under various wave conditions. Furthermore, the simplicity of using SMA springs as the actuator leads to the minimum number of moving mechanical parts, which can remarkably decrease maintenance costs. As the proof of concept, two types of tests are conducted in the laboratory using the same OWEC model under several random wave trains generated from spectra with different significant wave heights - one type with a fixed crest freeboard height and the other type featuring the adjustable crest freeboard height controlled by the springs. The substantial increase of harvested output power in the OWEC with the adjustable crest freeboard height may pave the way for more efficient wave energy conversion systems.

Natural montane peatlands generally are not a significant source of nitrous oxide (N₂O) due to environment limitation including phosphorus (P) scarcity and temperature lowness. Phosphorus enrichment and warming caused by global change are altering this limitation, likely to increase the source function of N₂O. However, the combined effects of P addition and warming on N₂O fluxes and biotic/abiotic factor in peatlands are still uncertain. To address this, we investigated the long-term (12 yrs) effects of P addition (5 and 10 kg ha^-1 yr^-1) and its interaction with warming on N₂O fluxes in a peatland. The results showed that although long-term P addition did not significantly affect the source/sink function of N₂O in the peatland, it stimulated enzyme activities, promoted peat decomposition. However, warming amplified the effect of P addition to increase N₂O emissions by stimulating enzyme activities and changing soil stoichiometry, even turned the peatland into a significant source of N₂O with an emission of approximate 100 g m^-2 during the growing season. Our study suggests that P enrichment under the current background of global warming will enhance the possibility of strong N₂O emissions in montane peatlands, which may increase the risk to further aggravate global warming.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

Microbial community succession in raw milk determines its quality and storage period. In this study, carbon dioxide (CO2) at 2000 ppm was used to treat raw milk to investigate the mechanism of extending the shelf life of raw milk by CO2 treatment from the viewpoint of microbial colonies and metabolites. The results showed that the shelf life of CO2-treated raw milk was extended to 16 days at 4 ℃, while that of the control raw milk was only 6 days. Microbiomics analysis identified 221 Amplicon Sequence Variants (ASVs) in raw milk, and the alpha diversity of microbial communities increased (P < 0.05) with the extension of storage time. Among them, Pseudomonas, Actinobacteria and Serratia were the major microbial genus responsible for the deterioration of raw milk, with a percentage of 85.7%. A combined metagenomics and metabolomics analysis revealed that microorganisms altered the levels of metabolites, such as pyruvic acid, glutamic acid, 5'- cmp, arginine, 2-propenoic acid, and phenylalanine in the raw milk through metabolic activities, such as ABC transporters, pyrimidine metabolism, arginine and proline metabolism and phenylalanine metabolism, and reduced the shelf life of the raw milk. CO2 treatment prolonged the shelf life of the raw milk by inhibiting the abundance of Gram-negative aerobic bacteria, such as Acinetobacter guillouiae, Pseudomonas fluorescens, Serratia liquefaciens and Pseudomonas simiae.

Background and objectives: TSC1 is a crucial component of the mTOR pathway, impacting cell growth, proliferation, and autophagy, while TSC2 is a tumor suppressor gene that regulates cell growth and is associated with the mTOR signaling pathway. In the present study, we analyzed TSC1 and TSC2 mRNA expression levels in rectal cancer, and evaluated the clinicopathological and prognostic characteristics of TSC1 and TSC2. Materials and Methods: TSC1 and TSC2 mRNA expression was examined in various cancer types. We further evaluated survival to determine the prognostic significance of TSC1 and TSC2 mRNA in CRC using The Cancer Genome Atlas (TCGA) data. Results: The study focused on rectal cancer, as it exhibited the most promising results. The patients were split into two subgroups, each comprising 50% of the total, based on the TSC gene expression levels. This division was made to assess the clinical characteristics associated with the expression of TSC1 and TSC2 genes. In the study, lower TSC1 expression was linked to venous invasion in rectal cancer patients, and there was also a related trend with lymphatic invasion, although it didn't reach statistical significance. Lower TSC2 expression was observed in younger patients and had some associations with sex and M stage, but these correlations were not statistically significant. When it came to survival analysis, TSC1 expression did not significantly impact overall survival, while higher TSC2 expression was associated with a poorer prognosis in rectal cancer. To enhance our comprehension, additional research, especially in larger case studies, is needed to explore the molecular mechanisms and clinical characteristics of TSC genes in colorectal cancer.

With the rapid evolution of SARS-CoV-2, the emergence of new strains is an intriguing question. This paper presents an evolutionary theory to analyze the mutations of the virus and identify the conditions that lead to the generation of new strains. We represent the virus variants using a 4-letter sequence based on amino acid mutations on the spike protein and employ an n-distance algorithm to derive a variant phylogenetic tree. We show that the theoretically-derived tree aligns with experimental data on virus evolution. Additionally, we propose an A-X model, utilizing the set of existing mutation sites (A) and a set of randomly generated sites (X), to calculate the emergence of new strains. Our findings demonstrate that a sufficient number of random iterations can predict the generation of new macro-lineages when the number of sites in X is large enough. These results provide a crucial theoretical basis for understanding the evolution of SARS-CoV-2.

Bond Properties were performed on Ag-2.35Au-0.7Pd-0.2Pt-0.1Cu alloy wire with a diameter of 25 µm under different process parameters. Effects of electrical flaming off (EFO) current and EFO time on deformability of the free air ball (FAB) were investigated using scanning electron microscopy (SEM) as well as the effects of ultrasonic power and bonding force on the bond characteristic. The experimental results showed that, FAB grows from a preheated tip to a small ball, a regular ball and finally to a golf ball with increasing either the EFO current or the EFO time, and the FAB presented optimal shape at 25 mA and 650 μs. Moreover, a nonlinear relationship between FAB diameter and EFO time is obtained at the EFO current of 25 mA, which could be expressed by a cubic equation. Further, at a constant bonding force, as the ultrasonic power increased, the mashed ball diameter grew larger and larger, the capillary hole imprint became more and more obvious, and the tail width also increased larger and larger, and vice versa. The optimal ultrasonic power and bonding force are 70 mW and of 45 gf for ball bond and 90 mW and 75 gf for wedge bond, respectively. Finally, for all the bonded wire samples prepared under optimal process parameters, no ball and wedge bond lifts happened after destructive pull test, and full intermetallic compound coverage with perfect morphology occurred on the bond pad after ball shear test, which meant that the bonded wire samples have high bond strength, and hence improved the reliability of microelectronic products.

Astragalus membranaceus (AM) and Panax ginseng (PG) are two herbal products with a long history of clinical usage in traditional Chinese medicine (TCM), used in treating a variety of diseases especially in stimulating or inhibiting the immune system. To elucidate the immunity effect of these two traditional Chinese medicine on animal model, four pharmacodynamic indexes (spleen index, thymus index, splenic lymphocyte proliferation and cytotoxic activity of natural killer (NK) cells) were observed on mice. Furthermore, metabolic profiles of plasma were also analyzed by ultra-performance liquid chromatography quadrupole-time-of-flight mass spectrometry (UPLC-Q/TOF-MS, LC-MS) method. All mice were intragastric administrated at three doses (low dose, moderate dose and high dose) once daily for 30 days. Principal components analysis (PCA) and orthogonal projection to latent structure discriminant analysis (OPLS-DA) were performed on LC-MS spectra of plasma, showing that all administration groups developed the disturbance of internal milieu, compared to the blank control (BC) group. Besides, correlation analysis was conducted between pharmacodynamic index and metabolic index. It indicated that uracil, lysoPC(18:3(6Z,9Z,12Z)), sphinganine, LPA(0:0/16:0), UDP-glucuronate, PC(14:0/18:0) were five main endogenous substances, much closely related to four immunological indexes. Glycerophospholipid metabolism was found in both AM and PG groups. Pyrimidine metabolism and sphingolipid metabolism were closely regulated in AM groups. Energy metabolism (starch and sucrose metabolism, Pentose and glucuronate interconversions, together with glycerolipid metabolism) and glycerolipid metabolism were found in PG groups. These findings could contribute to the understanding of mice plasmatic metabolic profiling after long-term administration. Comparative immune-related metabolomic analysis of AM and PG was obtained on the base of pathway analysis of immune-related biomarkers. PG groups trended to have effect on cytotoxic activity of NK cells. AM groups trended to effect thymus index. Our work provides a detailed interpretation of immunological characteristics in different traditional Chinese medicine on metabonomic level.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

Flexible implementations of Monte Carlo Tree Search (MCTS), combined with domain specific knowledge and hybridization with other search algorithms, can be a very powerful for the solution of problems in complex planning. We introduce mctreesearch4j, a standard MCTS implementation written as a standard JVM library following key design principles of object oriented programming. We define key class abstractions allowing the MCTS library to flexibly adapt to any well defined Markov Decision Process or turn-based adversarial game. Furthermore, our library is designed to be modular and extensible, utilizing class inheritance and generic typing to standardize custom algorithm definitions. We demon- strate that the design of the MCTS implementation provides ease of adaptation for unique heuristics and customization across varying Markov Decision Process (MDP) domains. In addition, the implementation is reasonably performant and accurate for standard MDP’s. In addition, via the implementation of mctreesearch4j, the nuances of different types of MCTS algorithms are discussed.

Large Language Models (LLMs) have demonstrated promising capabilities to solve complex tasks in critical sectors such as healthcare. However, LLMs are limited by their training data which is often outdated, the tendency to generate inaccurate ("hallucinated") content and a lack of transparency in the content they generate. To address these limitations, retrieval augmented generation (RAG) grounds the responses of LLMs by exposing them to external knowledge sources. However, in the healthcare domain there is currently a lack of systematic understanding of which datasets, RAG methodologies and evaluation frameworks are available. This review aims to bridge this gap by assessing RAG-based approaches employed by LLMs in healthcare, focusing on the different steps of retrieval, augmentation and generation. Additionally, we identify the limitations, strengths and gaps in the existing literature. Our synthesis shows that proprietary models such as GPT-3.5/4 are the most used for RAG applications in healthcare. Also, there is a lack of standardized evaluation frameworks for RAG-based applications. In addition, the majority of the studies do not assess or address ethical considerations related to RAG in healthcare. It is important to account for ethical challenges that are inherent when AI systems are implemented in the clinical setting. Lastly, we highlight the need for further research and development to ensure responsible and effective adoption of RAG in the medical domain.

A fern, Polypodium aureum, possesses a specialized spore-releasing mechanism like a catapult induced by quick expansion of vaporized bubbles. This study introduces lipid-coated perfluorocarbon droplets to enable repeatable vaporization-condensation cycles, inspired by the repeatable vaporization of Polypodium aureum. Lipid-perfluorocarbon droplets have been considered not to exhibit repeatable oscillations due to bubble collapse by low surface tension of lipid layers. However, a single lipid-dodecafluoropentane droplet with a diameter of 9.17 µm shows expansion-contraction oscillations over 4,000 cycles by changing lipid composition and applying low power of 1.7 MHz ultrasound to induce partial vaporization of droplets. The optimal combinations of shell composition, droplet fabrication, and acoustic conditions can minimize damage on shell structure and quick recovery of damaged shell layers. The highly-expanding oscillatory microbubbles provide a new direction for fuel-free micro or nanobots as well as biomedical applications of contrast agents and drug delivery.

Media thermal conductivity is important in various heat-transfer processes. Many conventional fluid conductors suffered low conductivity and environmental issues. Therefore, researchers developed efficient aqueous nanofluid conductors. Carbon nanotubes (CNTs) are widely studied to reach efficient, stable, low-cost and environmentally-friendly aqueous-nanofluids. This review provides a clear understanding of how CNTs improve thermal conductivity of aqueous nanofluids. A qualitative model is presented to explain literature mechanisms behind improvement. CNT type effects are discussed with other factors such as aspect ratio, Reynold number, dispersion quality, composition, temperature and additives. CNT functionalization is described. Relations to estimate nanofluid thermal conductivity are discussed. The model will help specialists to tailor CNT aqueous nanofluids as desired.

This article illuminates the reception and transformation of Ippen一遍(1234-1289)’s religious tenets and practices by Enju Kato加藤円住 (1919-2021) and his temple Shōjōkō-ji清浄光寺. While Enju Kato asserts that his life has been dedicated to adhering and enacting Ippen's concept of "renunci-ation," he has reinterpreted this concept based on his personal experiences and comprehension. Second, Enju Kato and Shōjōkō-ji have inherited some of Ippen's religious practices yet adapted these to align with contemporary settings. This article presents a case study discussing the ac-ceptance and transformation of doctrines and practices of jishū時宗 in contemporary era, which has been overlooked by academia thus far.

Transient receptor potential melastatin-8 (TRPM8) is a cation channel that is activated by cold and “cooling agents” such as menthol and icilin, which induce a cold sensation. Stimulation of TRPM8 activates an intracellular signaling cascade that ultimately leads to a change in the gene expression pattern of the cells. Here, we investigated the TRPM8-induced signaling pathway that links TRPM8 channel activation to gene transcription. Using a pharmacological approach, we show that inhibition of phosphatidylinositol 4-phosphate 5 kinase alpha (PIP5K), an enzyme essential for the biosynthesis of phosphatidylinositol 4,5-bisphosphate, attenuated TRPM8-induced gene transcription. Analyzing the link between TRPM8 and Gq proteins, we show that pharmacological inhibition of the beta gamma subunits impairs TRPM8 signaling. In addition, genetic studies showed that TRPM8 requires an activated Galpha subunit for signaling. In the nucleus, the TRPM8-induced signaling cascade triggers an activation of the transcription factor AP-1, a complex consisting of a dimer of basic region leucine zipper (bZIP) transcription factors. Here, we identified the bZIP protein c-Jun as an essential component of AP-1 within the TRPM8-induced signling cscade. In summary, with PIP5K, Gq subunits and c-Jun we have identified key molecules in the TRPM8-induced signaling from the plasma membrane to the nucleus.

The traffic light detection and recognition are crucial for enhancing the security of unmanned systems. This study proposes a YOLOv5-based traffic light detection algorithm to tackle the challenges posed by small targets and complex urban backgrounds. Initially, the mosaic-9 method is employed to enhance the training dataset, thereby boosting the network’s ability to generalize and adapt to real-world scenarios. Furthermore, the network incorporates the Squeezed-and-Excitation (SE) attention mechanism to improve. Moreover, the YOLOv5 algorithm’s loss function has been optimized by substituting it with EIoU_loss, which addresses issues like missed detection and false alarms. Experimental results demonstrate that the model , trained with this enhanced network, achieves a 99.4% mAP on a custom dataset, which is 6.3% higher than the original YOLOv5, while maintaining a detection speed of 74 f/s. Therefore, this algorithm offers higher detection accuracy and effectively meets real-time operational requirements.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

The “Crisis of Reproducibility” has received considerable attention both within the scientific community and without. While factors associated with scientific culture and practical practice are most often invoked, I propose that the Crisis of Reproducibility is ultimately a failure of generalization with a fundamental scientific basis in the methods used for biomedical research. The Denominator Problem describes how limitations intrinsic to the two primary approaches of biomedical research, clinical studies and pre-clinical experimental biology, lead to an inability to effectively characterize the full extent of biological heterogeneity, which compromises the task of generalizing acquired knowledge. Drawing on the example of the unifying role of theory in the physical sciences, I propose that multi-scale mathematical and dynamic computational models, when mapped to the modular structure of biological systems, can serve a unifying role as formal representations of what is conserved and similar from one biological context to another. This ability to explicitly describe the generation of heterogeneity from similarity addresses the Denominator Problem and provides a scientific response to the Crisis of Reproducibility.

In the aim of improving the positioning accuracy of monocular visual inertial simultaneous localization and mapping (VI-SLAM) system, an improved initialization method with faster convergence is proposed. This approach is classified as three parts: Firstly, in the initial stage, the pure vision measurement model of ORB-SLAM is employed to make all the variables visible. Secondly, the frequency of IMU camera was aligned by IMU preintegration technology. Thirdly, an improved iterative method is put forward for estimating the initial parameters of IMU faster. The estimation of IMU initial parameters is divided into several simpler sub-problems, containing direction refinement gravity estimation, gyroscope deviation estimation, accelerometer bias and scale estimation. The experimental results on the self-built robot platform show that our method can up-regulate the initialization convergence speed, simultaneously improve the positioning accuracy of the entire VI-SLAM system.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

Inorganic polymeric materials react slowly at room temperature and as a result usually require high-temperature curing. This study used the Arrhenius equation to analyze the correlation between curing temperature and curing duration during high-temperature curing. The test results show that optimal values exist for each alkali equivalent of the activator (weight ratio of Na2O/glass powder), curing temperature, and curing duration. Extending the curing duration and increasing the curing temperature have positive effects when the alkali equivalent is lower than the optimal value. However, over-curing results in invisible cracking in the specimens. Furthermore, despite exhibiting high strength initially, the strength of specimens gradually diminishes after standing in air. To ensure the durability of glass-based geopolymer, the curing temperature should not exceed 70℃, and the curing duration should be less than one day.

This study assessed farmers’ perception of climate change, estimated the determinants of, and evaluated the relationship among adaptation practices using the multivariate probit model. A survey in 300 agricultural households was carried out covering 10 sample districts considering five agro-ecological zones and a vulnerability index. Four adaptation choices (change in planting date, crop variety, crop type and investment in irrigation) were deemed as outcome variables and socioeconomic, demographic, institutional, farm-level and perceptions variables were deployed as explanatory variables. Their marginal effects were determined for three climatic variables—temperature, precipitation and drought. Age, gender and education of head of household, credit access, farm area, rain-fed farming and tenure, are found to be more influential compared to other factors. All four adaptation-options are found to be complimentary to each other. Importantly, the intensity of impact of dependent variables in different models, and for available adaptation-options, are found to be unequal. Therefore, policy options and support facilities should be devised according to climatic variables and adaptation options to achieve superior results.

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.

Melanogenesis is a biosynthetic pathway for producing of the pigment melanin in human skin. Tyrosinase, a key enzyme, catalyzing is the first step in melanogenesis and the downregulation of the tyrosinase enzyme activity is the most reported method for anti-melanogenesis. According to the hyperpigmentation as an important issue in cosmetic industry, there is a big demand for melanogenesis inhibitors. In the present study, we identified the anti-melanogenic effect of Inonotus Obliquus in α-MSH-induced B16F10 mouse melanoma cells as a new inhibitor. Comparing with control and Inonotus Obliquus extracts treated B16F10, we identified melanin contents, tyrosinase activity, tyrosinase mRNA and protein expression, MITF activity using a constructed plasmid. As shown in these results, we demonstrated that Inonotus Obliquus extracts down-regulated melanin synthesis using down-regulating activity and expression of tyrosinase which is key enzyme to produce melanin. In addition, we revealed expression of tyrosinase is regulated by MITF through repressing MITF transcriptional activity. Inonotus Obliquus extracts has potential to repress melanogenesis and decreased of hyperpigmentation and to use as cosmetic ingredient.

In autonomous driving systems, high-speed and real-time image processing, along with object recognition, are crucial technologies. This paper builds upon the research achievements in in-dustrial item sorting systems and proposes an object recognition and sorting system for auton-omous driving. In industrial sorting lines, goods sorting robots often need to work at high speeds to efficiently sort large volumes of items. This poses a challenge to the robot's real-time vision and sorting capabilities, making it both practical and economically viable to implement a real-time and low-cost sorting system in a real-world industrial sorting line. Existing sorting systems have limitations such as high cost, high computing resource consumption, and high power consump-tion. These issues lead to the fact that existing sorting systems are typically used only in large industrial plants. In this paper, we design a high-speed, low-cost, low-resource-consumption FPGA (Field-Programmable Gate Array) based item sorting system that achieves similar perfor-mance to current mainstream sorting systems at a lower cost and consumption than existing sorting systems. The recognition part employs a morphological recognition method, which segments the image using a frame difference algorithm and then extracts the color and shape features of the items. To handle sorting, a six-degree-of-freedom robotic arm is introduced in the sorting segment. The improved cubic B-spline interpolation algorithm is employed to plan the motion trajectory and consequently control the robotic arm to execute the corresponding actions. Through a series of experiments, this system achieves an average recognition delay of 25.26ms, ensures smooth operation of the gripping motion trajectory, minimizes resource consumption, and reduces implementation costs.

The greatly diversified flowering plants (angiosperms) are the dominating and defining group in the current earth ecosystem. However, from which group by what way the flowers, especially their gynoecia (key characteristics of angiosperms), are derived have been the questions in botany unanswered over centuries. Such an embarrassing situation can be attributed to the lack of plants with partially enclosed ovules, which are supposed to be a post between gymnosperms and angi-osperms. Here we report a fossil plant that has an apparent coniferous vegetative and reproduc-tive morphologies but has a single seed partially wrapped by the subtending bract. Such a mor-phology suggests that the carpels in angiosperms may be equivalent to bracts enclosing their axil-lary seed(s). Such a non-traditional interpretation of the homology of angiosperm carpels is com-patible with various new progresses made in botany and is in line with Tomlinson’s recent hy-pothesis. Together with other fossil evidence reported recently, it appears that gynoecia in angio-sperms are derived in multiple ways.

3D Zernike moments based on 3D Zernike polynomials have been successfully applied to the field of voxelized 3D shape retrieval and have attracted more attention in biomedical image processing. As the order of 3D Zernike moments increases, both computational efficiency and numerical accuracy decrease. Due to this phenomenon, a more efficient and stable method for computing high-order 3D Zernike moments was proposed in this study. The proposed recursive formula for computing 3D Zernike radial polynomials combines the recursive calculation of spherical harmonics to develop a voxel-based algorithm for the calculation of 3D Zernike moments. The algorithm was applied to the 3D shape Michelangelo's David with a size of 150×150×150 voxels. As compared to the method without additional acceleration, the proposed method uses a group action of order sixteen orthogonal group and saving unnecessary iterations, the factor of speed-up is 56.783±3.999 when the order of Zernike moments is between 10 and 450. The proposed method also obtained an accurate reconstructed shape with the error rate (normalized mean square error) of 0.00 (4.17×10^-3) when the reconstruction was computed for all moments up to order 450.

This study was to investigate and assess salivary biomarkers as a means of diagnosing periodontitis. A total of 121 subjects were included: 28 periodontally healthy subjects, 24 with stage I, 24 with stage II, 23 with stage III, and 22 with stage IV periodontitis. Salivary proteins including active matrix metalloproteinase-8 (MMP-8), pro-MMP-8, total MMP-8, C-reactive protein, secretory immunoglobulin A and planktonic bacteria including Aggregatibacter actinomycetemcomitans, Porphyromonas gingivalis, Tannerella forsythia, Treponema denticola, Fusobacterium nucleatum, Prevotella intermedia, Porphyromonas nigrescens, Parvimonas micra, Campylobacter rectus, Eubacterium nodatum, Eikenella corrodens, Streptococcus mitis, Streptococcus mutans, Staphylococcus aureus, Enterococcus faecalis, and Actinomyces viscosus were measured from salivary samples. The performance of the diagnostic models was assessed by receiver operating characteristics (ROC) and area under the ROC curve (AUC) analysis. The diagnostic models were constructed based on the subjects’ proteins and/or microbial profiles, resulting in two potential diagnosis models, which achieved better diagnostic powers with an AUC value &gt; 0.750 for the diagnosis of stage II, III, and IV periodontitis (Model PC-I; AUC: 0.796, sensitivity: 0.754, specificity: 0.712) and for the diagnosis of stage III and IV periodontitis (Model PC-II; AUC: 0.796, sensitivity: 0.756, specificity: 0.868). This study can contribute to screening for periodontitis based on salivary biomarkers.

Despite the best efforts in air-purification, airborne infectious diseases do and will continue to spread due to continuous emission of bioaerosols by the host/infected person. To tackle the rapid spread of airborne infectious diseases, a shift in focus from air-purification to bioaerosol disinfection/ decontamination is urgently needed. In this work, we studied a cold plasma ionizer (CPI) and electrostatic precipitator (ESP)-coupled CPI (CPI-ESP) for disinfection and cleaning of bioaerosols. Using porcine respiratory coronavirus (PRCV) and E. coli in a testing chamber, we demonstrated that CPI coupled with ESP is an effective technology for inactivating aerosolized microorganisms and microorganisms spread on surfaces. In addition, we have demonstrated the efficiency of a CPI-ESP coupled device for disinfection of naturally occurring airborne microbials in a few indoor settings (i.e., an living room, a discussion room, a schoolroom and an office) to determine the treatment duration- and human activity-dependent efficacy. To understand the disinfection mechanism, we conduced fluorescence microscopy study to reveal different degree of bacteria cell membrane damage under CPI treatment.

Macrophages exhibit impaired phagocytosis, adhesion, migration, and cytokine production in space, hindering their ability to elicit immune responses. Considering that the combined effect of spaceflight microgravity and radiation is multiscale and multifactorial in nature, it is expected that contradictory findings are common in the field. This theory paper reanalyzes research on the macrophage spaceflight response across multiple timescales from seconds to weeks, and spatial scales from the molecular, intracellular, extracellular, to the physiological. Key findings include time-dependence of both pro-inflammatory activation and integrin expression. Here, we introduce the time-dependent, intracellular localization of MRTF-A as a hypothetical confounder of macrophage activation. We discuss the mechanosensitive MRTF-A/SRF pathway dependence on the actin cytoskeleton/nucleoskeleton, microtubules, membrane mechanoreceptors, hypoxia, oxidative stress, and intracellular/extracellular crosstalk. By adopting a multiscale perspective, this paper provides the first mechanistic answer for a three-decade-old question regarding impaired cytokine secretion in microgravity—and strengthens the connection between the recent advances in mechanobiology, microgravity, and the spaceflight immune response. Finally, we hypothesize MRTF involvement and complications in treating spaceflight-induced cardiovascular, skeletal, and immune disease.

Migraine is one of the leading causes of disability worldwide [1,2]and patients with acute migraine frequently present to emergency departments (ED)[3]. The current literature suggests that ED treatment of migraine headache varies across institutions [4-7]. Considering this, we conducted a scoping review to summarize trends in medication prescribing patterns for acute migraine treatment in the ED setting. Trends were evaluated for factors influencing treatment choices, with particular attention placed on opioids and migraine specific therapy. This scoping review was based on the Arksey and O'Malley methodological framework[8]and included studies published between 1 January 2000 until 31 May 2020. 14 publications met the inclusion criteria. The most common classes of medication prescribed were often anti-emetics or Non-steroidal anti-inflammatory drugs (NSAID), but rates varied between studies. There was a concerning trend towards an underutilization of triptans and overutilization of opiates. The use of specific clinical goals of treatment (e.g. two-hour pain free freedom response) was also not evident. Additionally, 88% (n=8) of the 9 studies commenting on adherence to hospital or evidence-based guidelines stated that practices were non-adherent. Overall, the reviewed literature reveals treatment practices for acute migraine in the ED are heterogeneous and deviate from established international recommendations.

The scale of China's floating population is very large, and it is a key group that needs attention in promoting the equalization of basic public services. This study explores the impact and mechanism of adjusting the urban household registration threshold on the acquisition of citizenship status by the "rural-urban" floating population, with the household registration threshold as the link. It was found that the threshold for household registration has an impact on the willingness of rural urban migrant population to settle down from two aspects. On the one hand, a high threshold for household registration implies the unaffordability of obtaining citizenship status for the "rural-urban" migrant population, which has a significant crowding out effect on their willingness to settle down. Moreover, the high skilled "rural-urban" migrant population without housing is more sensitive to the high threshold for household registration. On the other hand, from the perspective of urban scale, the increase in the threshold for household registration has had a crowding out effect on the floating population for Type I large cities, mega cities, and super large cities. The increase in the threshold for settling in mega cities has the strongest crowding out effect on the floating population, which means that as the urban population expands, the welfare benefits enjoyed by the floating population in these cities will decrease, leading them to be more inclined to leave these cities and seek development opportunities in other cities. This study effectively answers how the threshold for household registration affects the willingness of rural urban migrant population to settle, providing mathematical support for urban development.

This article explores the apologetic discourse towards the convergence between Pure Land Buddhism and science of the contemporary Chinese Buddhist monk Da An (1959- ). Faced with the formidable challenge posed by contemporary science towards public acceptance of Buddhism, Da An endeavors to employ science as a medium for propagating Pure Land teachings, seeking to accommodate the preferences of scientifically inclined individuals. He utilizes several theoretical physics concepts to validate that certain ostensibly miraculous accounts within Pure Land Buddhist texts are not incompatible with contemporary science. Further, he asserts that certain supernatural narratives therein indicate that some physical principles still residing in theoretical conjectures on Earth have already been validated and can be utilized at will by the celestial beings in Sukhāvatī, thus asserting the supremacy of Pure Land teachings over science. The article endeavors to examine the contemporary dialogue between Pure Land Buddhism and science, which has been overlooked in the current research realm of the interaction between Buddhism and science.

Widespread poverty is the most serious threat and social problem that Bangladesh faces. Regional vulnerability to climate change threatens to escalate the magnitude of this poverty. It is essential that projections of poverty be made while bearing in mind the effects of climate change. The main purpose of this paper is to investigate the agrarian sub-national regional analysis of climate change vulnerability in Bangladesh under various climate change scenarios and its potential impact on poverty. This study is relevant to socio-economic research on climate change vulnerability and agriculture risk management and has the potential to contribute new insights to the complex interactions in household income and climate change risks to agricultural communities in Bangladesh and South Asia. The current study uses analysis of variance, cluster analysis, decomposition of variance and log-normal distribution to estimate the parameters of income variability that ascertain vulnerability levels and help us to understand the poverty levels that climate change could potentially incur. It is found that the income share in income sources revealed that income category shares across the various regions of Bangladesh are far from uniform. The variance decomposition of income showed that agricultural income in Mymensingh and Rangpur is the main cause of income difference. Moreover, large variance of agricultural income in the regions is induced by gross income from rice production. Additionally, constant reduction of rice yield due to climate change in Bangladesh is not such a severe problem for farmers, however, the extreme events like flood, flash flood, drought, sea level rise, and greenhouse gas emission based on RCPs could increase the poverty rates in Mymensingh, Rajshahi, Barisal, and Khulna regions that would be highly affected by unexpected yield loss due to extreme climatic events. Therefore, research and development of adaptation measures to climate change for regions where farmers are largely dependent on agricultural income is important.

Prompt removal of misfolded membrane proteins and misassembled membrane protein complexes is essential for membrane homeostasis. However, the elimination of these toxic proteins from the hydrophobic membrane environment has high energetic barriers. Transmembrane FtsH is the only known ATP-dependent protease responsible for this task, unlike other well-studied soluble ATP-dependent proteases. The mechanisms by which FtsH recognizes, unfolds, translocates, and proteolyzes its substrates remain unclear. Here, we report the crystal structures of the Thermotoga maritima FtsH periplasmic domain (PD) in an associative trimeric state at a 1.5-1.95 Å resolution. We also describe the pH-dependent oligomerization states of the isolated PD using dynamic light scattering. These observations help us understand how FtsH recognizes membrane-anchored misfolded proteins.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

Gas flaring is commonly used by industrial plants for processing oil and natural gases in the atmosphere, and hence is an important anthropogenic source for various pollutants including CO₂, CO, and aerosols. This study evaluates the feasibility of using satellite data to characterize gas flaring form space by focusing on the Khanty Mansiysk Autonomous Okrug in Russia, a region that is well known for its dominatingly gas flaring activities. Multiple satellite-based thermal anomaly data products at night are inter-compared and analyzed, including MODIS (Moderate Resolution Imaging Spectroradiometer) Terra level-2 Thermal Anomalies product (MOD14), MODIS Aqua level-2 Thermal Anomalies product (MYD14), VIIRS (Visible Infrared Imaging Radiometer Suite) Active Fires Applications Related Product (VAFP), and VIIRS level-2 data based Nightfire product (VNF). The analysis compares and contrasts the efficacy of these sensor products in detecting small, hot sources like flares on the ground in extremely cold environments such as Russia. We found that the VNF algorithm recently launched by NOAA has the unprecedented accuracy and efficiency in characterizing gas flares in the region owing primarily to the use of Shortwave Infrared (SWIR) bands. Reconciliation of VNF’s differences and similarities with other nighttime fire products is also conducted, indicating that MOD14/MYD14 and VAFP data are only effective in detecting those gas flaring pixels that are among the hottest in the region. Validation of VNF product of gas flaring location with Google Earth images are made. It is shown that that VNF’s estimates of gas flaring area (the area of gas flaming) agree well the counterparts from Google images with a linear correlation of 0.91, highlighting its potential use for routinely monitoring emissions of gas flaring from space.

We investigated experimentally, analytically and numerically the formation process of double emulsion formations under dripping regime in a tri-axial co-flow capillary device. The results show that mismatches of core and shell droplets under a given flow condition can be captured both experimentally and numerically. We propose a semi-analytical model using the match ratio between the pinch-off length of the shell droplet and the product of the core growth rate and its pinch-off time. The mismatch issue can be avoided if the match ratio is lower than unity. We considered a model with the wall effect to predict the size of the matched double emulsion. The model shows slight deviations with experimental data if the Reynolds number of continuous phase is lower than 0.06, but asymptotically approaches to good agreement if the Reynolds number increases from 0.06 to 0.14. The numerical simulation generally agrees with the experiments under various flow conditions.

Amidst the escalating demands for efficient Intelligent Transportation Systems (ITS) management, the significance of accurate Origin-Destination (OD) data prediction has emerged as a paramount concern, given its indispensable role in the ITS domain. This paper introduces a groundbreaking integrated model, creatively fusing the unique strengths of Graph Convolutional Network (GCN), Residual Neural Network (ResNet), and Long Short-Term Memory Network (LSTM) into a single architecture, which we name GraphResLSTM, to exploit road segment average speed data for OD prediction. Compared with conventional road segment traffic volume data, average speed data is more readily available, significantly reducing the data accessibility barrier for OD prediction. We underscore the critical role of selection of key road segments and employs a combination of Entropy Weight Method and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) to identify 41 representative road segments from the experimental road network. In the experimental phase, we simulate 86400000 seconds of traffic conditions, generating a total of 1440000 data records. Utilizing these simulated data, we design and conduct comparative experiments between models as well as data types. The results demonstrate that both the GraphResLSTM model and road segment average speed data outperform other models and data types notably in OD prediction tasks.

Wireless Sensor networks (WSNs) are gaining more and more research interest due to their ability to monitor large areas more or less independent. However, their reliability is an important issue, since their system reliability is influenced from a hardware, a data and an energetic point of view due to different factors like loading conditions, signal attenuation and battery lifetime. Regarding these issues, the positions of sensor nodes have to be chosen correctly to maximize the system reliability, which has to be considered during the development of new products equipped with WSNs. In this paper, an approach to estimate a WSNs system reliability during the development phase based on the analysis of the measurements on the example of strain measurements in finite elements (FE) models is presented. For that, the part under consideration is divided into regions with similar strains by the use of a Region Growing Algorithm (RGA). Afterwards, the WSN’s configuration is analyzed regarding its reliability in accordance to the data paths and measurement redundancy due to the sensor positions in the found measuring regions. This methodology is tested on an exemplary WSN configuration at an aircraft wing box under bending load and was found to work very well regarding the estimation of the hardware perspective on the system reliability. Therefore, the methodology and the developed algorithm show potentials for optimizations in sensor node positions for better reliability results.

Reliable access to electricity has become a necessity worldwide, and without it, no country can operate health systems and achieve sustainable development goals (SDGs). However, while developed countries have been successfully electrified for many decades, most developing countries have fallen short, contributing to significant impacts, particularly the health sector. The present study explores the relationship between electrification and health vulnerability in developing countries between 1990 and 2020 using the Feasible Generalized Least Square (FGLS) approach. The varied electrification across countries motivates the use of non-linear associations between electrification and health vulnerability. We demonstrate that electrification and health vulnerability have an inverted U-shaped association. Further analysis indicates that most developing countries have achieved a mature level of an inverted U-shaped curve, showing a reduction in health vulnerability with increasing electrification. There are few developing countries, mainly African countries, struggling to reach maturity. The results of this study indicate the need for increased access to electrification, in combination with a reduction in the use of biomass and fossil fuel feedstocks, to mitigate health vulnerability in developing countries.

Atta capiguara is a grass-cutting ant species frequently found in Cerrado biome. However, little is known about the giant nest architecture of this ant. In this study, we investigated the architecture of three A. capiguara nests from the fragment of cerrado in Botucatu, São Paulo, Brazil. Casts were made of the nests by filling them with cement to permit better visualization of internal structures such as chambers and tunnels. After excavation, the depth and dimensions (length, width, and height) of the chambers were measured. The results showed the typical shape of Atta capiguara nests consisting of mounds of loose soil with unique features resembling a conic section. The fungus chambers were found outside the apparent main part of the nest and were spaced apart and distributed laterally at ground level. The waste chambers were located beneath the largest mound of loose soil. Both the fungus and waste chambers exhibited a sectoral distribution. Our study contributes to a better understanding of the so far unknown nest architecture of the grass-cutting ant A. capiguara.

Data mining plays a critical role in the sustainable decision making. The k-prototypes algorithm is one of the best-known algorithm for clustering both numeric and categorical data. Despite this, however, clustering a large number of spatial object with mixed numeric and categorical attributes is still inefficient due to its high time complexity. In this paper, we propose an efficient grid-based k-prototypes algorithms, GK-prototypes, which achieves high performance for clustering spatial objects. The first proposed algorithm utilizes both maximum and minimum distance between cluster centers and a cell, which can remove unnecessary distance calculation. The second proposed algorithm as extensions of the first proposed algorithm utilizes spatial dependence that spatial data tend to be more similar as objects are closer. Each cell has a bitmap index which stores categorical values of all objects in the same cell for each attribute. This bitmap index can improve the performance in case that a categorical data is skewed. Our evaluation experiments showed that proposed algorithms can achieve better performance than the existing pruning technique in the k-prototypes algorithm.

Background: Existing human cell immortalization methods made the cells obtain oncogenesis phenotype and/or caused the cells gain and/or lose chromosomes. Immortalized normal human T cells lines provide critical in vitro models for basic research and therapeutic products development.Methods: We utilized a CRISPR/Cas9 system to replace a single copy of the exon 2 of the cell cycle inhibitor gene CDKN2A (encoding p16 and p14 proteins) with a single copy of human telomerase reverse transcriptase (hTERT) to immortalize human primary CD8⁺ T cells (hCD8⁺T-TERT). By using Cas9 protein and low donor DNA copies/cell, we successfully immortalized hCD8⁺T cells with a single copy of hTERT transgene, which also avoided uncontrolled insertion of Cas9 gene and guide RNA vector.Results: Human primary CD8+ cells were immortalized and expanded more than 2.6 × 10⁷ times. Characterization of the cells revealed that the immortalized CD8⁺ T-TERT cells retained most of the cell surface markers and normal karyotype. The CD8⁺ T-TERT cells also retained the dependence of IL-2 and CD3/CD28 activator for survival and expansion.Conclusion: we established a stable immortalized CD8⁺ T cell line that had a phenotype consistent with T cells and will be a useful research model.

A Micro holes in a diamond are presented by using a homemade femtosecond (fs) Yb:KGW laser. An fs laser source was used emitting pulse duration of 230 fs at 1030 nm wavelength, whereas the spot size amounted to 8.9 μm. Parameters like pulse energy, and pulse number were varied over a wide range in order to evaluate their influence both on the micro hole geometry like hole diameter, circularity, taper angle, and on the drilling quality. Hourglass-shaped micro holes whose diameters decrease and increase again after a certain depth have important applications. The results demonstrate the feasibility of extending the drilling of an hourglass-shaped hole in a diamond sample, which has similar diameters at the hole entrance (92 μm) and exit (95 μm), but a much smaller diameter (28 μm) at a certain waist section inside the hole.

Today’s intruders usually send attacking commands to a target system through several stepping-stone hosts, in order to reduce the chance of being detected. With stepping-stone intrusion (SSI), the intruder’s identity is hidden behind a long interactive chain of hosts and very hard to detect. An effective approach for SSI detection (SSID) is to estimate the length of the chain. This type of method is called network-based SSID. Most existing network-based SSID worked effectively only when intruders’ session manipulation was not present. These known SSID algorithms are either weak to resist intruders’ chaff-perturbation manipulation or having very limited capability in resisting attacker’s session manipulation. This paper develops a novel network-based SSID algorithm resistant to intruders’ chaff-perturbation by using packet crossover. Our proposed SSID algorithm is simple and easy to implement as the number of packet crossovers can be easily computed. We conduct rigorous technical proofs to verify the correctness of our proposed algorithm. The experimental results show that our proposed SSID algorithm works effectively and perfectly in resisting intruders’ chaff-perturbation up to 50% chaff rate.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

The Gurney flap (GF) is a miniature lift-enhancement device and is usually mounted at the trailing edge of an airfoil. The GF and has been successfully applied to isolated airfoils, multi-element airfoils, and aircraft wings as well as helicopter rotor due to its attractive features of simplicity, cost-effective and separation control. The GF also has aroused the attention of researchers in the turbomachinery industry. However, limited studies are currently available on the application of a GF to an axial fan.Hence, in this paper, we conduct a wind tunnel and computational fluid dynamic (CFD) investigation on an axial fan profiled with a NACA 65-(12)10 airfoil to evaluate the effect of the GF on the performance of the fan. We also present the detailed flow features of the fan with and without the GF after validating the simulation results with the experimental results. The experimental results show that as the GF is installed higher on the fan blade, it can produce a higher total pressure rise accompanied with a greater loss of efficiency. The installation of the GF also enlarges the work capacity of the fan. Detailed flow field analysis, including the surface pressure distribution, vorticity distribution at the trailing edge and streamline distribution of the fan, is carried out to understand the mechanisms of the effect of the GF on the performance of the fan.

This paper introduces in general the conservation work of the Nara Palace Site in Japan carried out by Japanese conservation experts. Concerning conservation theory, this paper focused on the international conventions in which the 1994 Nara Document on Authenticity plays an important role in contributing to Japanese cultural heritage conservation achievements with the expansion of Cultural diversity and Heritage diversity, the Values and Authenticity conceptions which proposed a new orientation in terms of awareness and openness broader vision in identifying architectural heritage values. Regarding, based on the 1994 Nara Document on Authenticity, the 1964 Venice Charter, and the 1999 Bura Charter, we try to propose a new concept of the so-called “Architectural Heritage DNA” and its potential structure, providing a simple formula for the authentic values appraisal of the heritage conservation works. In addition, we also try to supplement the concept of Inheritance between Conservation and Development which is the lack of international conventions of cultural heritage conservation. The viewpoints expressed in this paper are based on the most common concepts of international conventions but interpreted in a new-understandable, practical, and highly applicable way possible to the current socio-political situation and in the future, as well.

Novel 1,2,3-triazole compounds 3–4 were synthesised via the regioselective addition and cyclization reaction of 1,1-enediamines (EDAMs) 1 with p-methylbenzenesulfonyl azide (TsN₃) 2 in 1,4-dioxane at refluxing for 5 hours. As a result, 1,2,3-triazoles 3–4 can be easily and efficiently obtained via catalyst-free click chemistry. The reactions have some advantages such as metal-free catalyst, excellent yield, inexpensive raw materials, and convenient final treatment.

In the last two decades, the discovery of various pathways involved in renal cell carcinoma (RCC) have led to the development of biologically-driven targeted therapies. Hypoxia inducible factors (HIFs), angiogenic growth factors, von Hippel-Lindau (VHL) gene mutations and oncogenic miRNAs play essential roles in the pathogenesis and drug resistance of clear cell renal cell carcinoma. These insights have led to the development of VEGF inhibitors, mTOR inhibitors and immunotherapeutic agents which have significantly improved outcomes of patients with advanced RCC. HIF inhibitors will be a valuable asset in the growing therapeutic armamentarium of RCC. Various histone deacetylase (HDAC)inhibitors, including selenium and agents such as PT2385 and PT2977, are being explored in various clinical trials as potential HIF inhibitors to ameliorate the outcomes of RCC patients. In this article, we will review the current treatment options and highlight the potential role of selenium in the modulation of drug resistance biomarkers expressed in ccRCC tumors.

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

Acoustic metasurface are artificial structures which could manipulate the wavefront in sub-wavelength dimensions and the previous proposed acoustic metasurface were mostly realized with single materials. An acoustic metasurface with composite structure is proposed for underwater acoustic stealth considering both wavefront manipulation and sound absorption. The unit cells of the metasurface are composed by metallic supporting lattice, interconnecting polymer materials and mass balancing columns. With the gradual modulations of equivalent physical properties along the horizontal direction of metasurface, the incident acoustic wave is reflected to other directions. Meanwhile, the polymer material inside the unit cells would dissipate the acoustic wave energy due to inherent damping properties. With the simultaneous modulations of reflected wave direction and scattering acoustic amplitude, significant improvement of underwater stealth effect is achieved. Compared with single-phase metasurface, the Far-Field Sound Pressure Level (FFSPL) of the multiphase metasurface decreased by 4.82 dB within the frequency range of 3kHz~30kHz. Under a hydrostatic pressure of 5MPa, the linearized mean stress for multiphase metasurface is only 1/3 of that of single-phase metasurface due to much thicker struts and much more uniform stress distribution. The proposed composite structure possesses potential applications due to acceptable thickness (80mm) and low equivalent density (1100 kg/m3).

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

The purpose of this study is to analyze how global research cooperation patterns in the secondary battery industry have changed over recent years and to identify the evolution in the focus of research. To this end, network analysis was performed using the nationality information of the authors of a 10-year multinational joint research paper related to lithium-ion batteries. Furthermore, keyword analysis and topic modeling were performed using the abstract data from the study. The results of this study confirm that some countries that are not well-known in the field, such as Australia, Spain, and France, showed high centrality, compared with the level of cooperation scale. Additionally, six research topics were identified. According to a comparison over the first half of the decade, no difference was observed in the appearance of keywords indicating high energy density and conductivity with lithium, a key mineral. Keyword distribution was high for topics like battery charging and discharging in the first half of the decade, and for next-generation battery materials, such as solid electrolytes, lithium metal anodes, and lithium-sulfur batteries in the second. These results provide insights into the establishment of R&D cooperation strategies by countries and pre-planning by companies in the battery industry.

The primary attraction of IaaS is providing elastic resources on demand. It becomes imperative that IaaS-users have an effective methodology for learning what resources they require, how many resources and for how long they need. However, the heterogeneity of resources, the diversity resource demands of different cloud applications and the variation of application-user behaviors pose IaaS-users big challenge. In this paper, we purpose a unified resource demand forecasting model suiting for different applications, various resources and diverse time-varying workload patterns. With the model, taking input from parameterized applications, resources and workload scenarios, the corresponding resources demands during any time interval can be deduced as output. The experiments configure concrete functions and parameters to help understanding the above model.

The current outbreak of coronavirus disease (COVID-19) caused by SARS-CoV-2 in Wuhan, China has killed more than 2600 people since December 2019. Currently there is no effective treatment for this epidemic. Drug for anti SARS-CoV-2 are urgently needed. In this study we evaluated two compound libraries containing launched drugs and compounds from 300 kinds of Traditional Chinese Medicine in order to find anti SARS-CoV-2 drugs. Docking and then calculating binding free energy were performed as workflow against four key anti-SARS-CoV-2 drug targets, 3CLpro, PLpro and RdRp from SARSCoV-2, and AAK1 from human as well. As a result, drugs launched with potential for antiviral usage were selected in the hope of providing some knowledge for future drug discovery.

Candida albicans, a prominent constituent of the human microbiota, poses a significant health threat due to its opportunistic pathogenicity and adept biofilm-forming capabilities. This research delves into the antifungal attributes and biofilm inhibition potential of Tea Tree Oil (Melaleuca alternifolia) cultivated in Vietnam. Renowned for its bioactive compounds, including terpinen-4-ol, 1,8-cineole, and terpinolene, the essential oil of Melaleuca alternifolia, commonly referred to as tea tree oil (TTO), is scrutinized for its impact on Candida albicans. The study meticulously determines the Minimum Inhibitory Concentration (MIC) and Minimum Fungicidal Concentration (MFC) of TTO against Candida albicans in both planktonic and biofilm states. Additionally, it assesses the biofilm-forming capacity of Candida albicans and establishes the Minimum Biofilm Inhibitory Concentration (MBIC) and Minimum Biofilm Eradication Concentration (MBEC) of TTO. Employing a liquid culture dilution method within a defined concentration range of 0.1 μL/mL to 10 μL/mL, the experimental approach adheres to established protocols. The outcomes reveal a noteworthy MIC and MIC₈₀ of 0.1 μL/mL and 2 μL/mL, respectively, and an MFC of 10 μL/mL for TTO against Candida albicans. Furthermore, TTO exhibits an MBIC of 2 μL/mL, showcasing its efficacy in inhibiting biofilm formation. However, the MBEC of TTO remains uncertain, possibly due to insufficient concentration tested, which may not effectively disrupt over 50% of the pre-formed biofilm mass within 24 hours. These results underscore the promising potential of TTO as a potent antifungal agent and biofilm inhibitor against Candida albicans, offering valuable insights for the innovation of novel therapeutic strategies in the realm of fungal infections.

Abstract: Objectives: To establish the expression profile of N6-methyladenosine(m6A) modifications in the hippocampus of mice with diabetic cognitive impairment (DCI) and elucidate the potential regulatory mechanism. Methods: A DCI model was established by feeding a high-fat diet to C57BL/6J mice. m6A and RNA sequencing was conducted to profile the m6A-tagged transcripts in the hippocampus. Results: Methylated RNA immunoprecipitation with next-generation sequencing and RNA sequencing analyses yielded differentially m6A-modified and expressed genes in the hippocampus of DCI mice, which were enriched in pathways involving synaptic transmission and axonal guidance. Mechanistic analyses revealed a remarkable change in m6A modification levels through alteration of the mRNA expression of m6A methyltransferases (METTL3 and METTL14) and demethylase (FTO) in the hippocampus of DCI mice. Conclusions: We identified a co-mediated specific RNA regulatory strategy that broadens the epigenetic regulatory mechanism of RNA-induced neurodegenerative disorders associated with metabolic and endocrine diseases.

This paper proposes a new non-radial biennial Luenberger energy and environmental performance index (EEPI) to measure the EEP change in various Chinese cities. The sources of EEP change, in terms of technical efficiency change and technological change, are examined by Luenberger EEPI. The contributions from specific undesirable outputs and energy inputs to the EEP change are identified by means of the non-radial efficiency measure. The proposed approach is applied to evaluate the EEP of the industrial sector in 283 cities in China over 2010-2014. Factors influencing the emission abatement potential are investigated by employing geographically weighted regression (GWR) model. We find that 1) changes in EEP can be attributed to technological progress but that technological progress slows down across the study period; 2) the soot emission performance experiences a downtrend among four specific sub-performances in line with the truth that severe haze happened frequently in China; 3) the best performers begin to move from the coastal to inland cities with the less resource consumption and higher ecological equality; 4) cities with the strongest positive effect in regards to pollution intensity on emission abatement potential are located in the areas around the Bohai Gulf, where air pollution is particularly severe.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Higher education informatization (HEI) is an interdisciplinary field that examines the use and integration of information and communication technologies (ICTs) in higher education. This paper provides a bibliometric and visual analysis of the research trends, patterns, and topics in this field. Using the Web of Science database, we selected and analyzed 199 SCI and SSCI papers on HEI published from 2000 to 2023 by VOSviewer and CiteSpace software. The results indicate that the publication volume of HEI research has grown significantly in recent years, with China and the US being the most productive and influential countries. The author network shows the collaboration and contribution of different researchers and institutions, while the journal network reveals the multidisciplinary nature and scope of the field. The keyword network and the burst keyword analysis identify the main research themes and the emerging hot topics in HEI, such as online learning, big data, and artificial intelligence. The co-citation network of sources illustrates the theoretical and methodological foundations and influences of the field. The paper concludes with some implications and suggestions for future HEI research.

A robust guaranteed cost preview repetitive controller is proposed for a class of polytopic uncertain discrete-time systems. In order to improve the tracking performance, the repetitive controller combined with preview compensator is inserted in the forward channel. By using the L-order forward difference operator, an augmented dynamic system is constructed. Then, the guaranteed cost preview repetitive control problem is transformed into the guaranteed cost control problem for the augmented dynamic system. For given performance index, the sufficient condition of asymptotic stability for the closed-loop system is derived by combining parameter-dependent Lyapunov function method with linear matrix inequality (LMI) techniques. By incorporating the controller obtained into the original system, the guaranteed-cost preview repetitive controller is derived. A numerical example is also included to show the effectiveness of the proposed method.

Telemedicine has become an interesting research topic in recent years, especially since the start of the COVID-19 pandemic. This article conducts research using a systematic literature review to identify paradoxes in telemedicine services. The research method follows the steps in a systematic literature review, by accessing the Scopus journal database to search for relevant articles between 2018 and 2024. The selected articles were selected based on certain inclusion and exclusion criteria, resulting in 28 relevant articles which were then analyzed to understand findings related to paradoxes in telemedicine services. The research results show four main clusters of paradoxes in telemedicine research, namely health services, health quality, the COVID-19 pandemic, and technology. Each cluster shows complex opportunities and challenges in efforts to improve health services through telemedicine. Understanding the clusters for each article can then be mapped to the organizational categories in the Dynamic Equilibrium Model. In conclusion, this study provides a comprehensive insight into the paradoxes in telemedicine services, highlighting the importance of understanding the various aspects involved in the adoption and implementation of this technology. With a better understanding of this paradox, it is hoped that society and health practitioners can overcome the challenges and exploit the opportunities offered by telemedicine to improve the accessibility and quality of health services in the future.

Digital healthcare systems play a pivotal role in providing efficient and accessible healthcare services. However, ensuring secure authentication and key agreement mechanisms is essential to protect sensitive patient data and maintain the integrity of the system. The existing methods face limitations in terms of vulnerability to cyber attacks, scalability, and resource utilization. Furthermore, the integration of blockchain technology introduces new complexities that need to be addressed. This research proposes an optimized fuzzy logic approach combined with blockchain technology to address the authentication and key agreement challenges in digital healthcare systems. The proposed solution leverages the flexibility and adaptability of fuzzy logic algorithms to handle uncertainty and imprecision in authentication decisions. By employing fuzzy logic, the system can effectively minimize false positives and false negatives, enhancing the robustness against adversarial attacks. Moreover, the integration of blockchain technology provides a decentralized and tamper-proof infrastructure for securely storing and managing authentication and key agreement data. This ensures transparency and trust in the system, mitigating the risks of unauthorized access and data manipulation. The blockchain-based architecture also enables efficient resource utilization and scalability, allowing the system to handle authentication requests in a timely manner, even in large-scale digital healthcare environments.The proposed method is evaluated by using the NIST Special Database 302 and it shows superior performance compared to existing methods, with minimum False Rejection Rate (FRR), False Acceptance Rate (FAR), and response time. Moreover, the proposed method minimizes communication overhead during the authentication process and resists different cyber attacks including a Replay attack, Man-in-the-middle attack, Denial of Service (DoS) attack, and Impersonation attack. The proposed method achieves excellent performance in terms of security, efficiency, and resistance to various cyber-attacks, making it a promising approach for secure data sharing in P2P cloud environments.

The connected vertex cover (CVC) problem is a variant of the vertex cover problem, which has many important applications, such as wireless network design, routing and wavelength assignment problem, etc. A good algorithm for the problem can help us improve engineering efficiency, cost savings and resources in industrial applications. In this work, we present an efficient algorithm GRASP-CVC (Greedy Randomized Adaptive Search Procedure for Connected Vertex Cover) for CVC in general graphs. The algorithm has two main phases, i.e., construction phase and local search phase. To construct a high quality feasible initial solution, we design a greedy function and a restricted candidate list in the construction phase. The configuration checking strategy is adopted to decrease the cycling problem in the local search phase. The experimental results demonstrate that GRASP-CVC is competitive with the other competitive algorithm, which validate the effectivity and efficiency of our GRASP-CVC solver.

In this work, a novel silane coupled cationic precursor (SAGS) was synthesized by 3-glycidyloxypropyltrimethoxysilane and sodium 2-((2-aminorthyl)amino) ethanesulfonate. A series of cation exchange membranes were prepared with poly(vinyl alcohol) (PVA) and SAGS by sol-gel process. The structure of the prepared membranes were characterized by fourier transform infrared spectrum (FTIR) and scanning electron microscopy (SEM), and its properties were studied by water uptake (WR), cation exchange capacity (CEC), linear expansion ratio (LER), alkali stability, thermogravimetric analysis (TGA), mechanical properties and diffusion dialysis performance. FTIR and X-ray photoelectron spectroscopy (XPS）confirmed the successful preparation of SAGS membranes, and SEM images showed that the prepared membranes were dense and uniform. The WR values of the SAGS membranes were in the range of 91.49-122.39 %, and the LER values were 17.65-28.21 %. In addition, the SAGS membranes had suitable CEC value, good alkali resistance and thermal stability which ensured the application of membranes in the field of diffusion dialysis (DD) for alkali recovery. In DD test, the dialysis coefficients of NaOH (UOH) ranged from 0.012 mm/h to 0.023 mm/h, and the separation factors (S) was in the range of 30.77-16.43. In summary, the prepared membrane had good performance and simple preparation process, which had great application potential in textile industrial wastewater recovery.

In mesoscale eddies, chemical properties and biological composition are different from those in surrounding water, due to their unique physical processes. It is unclear how physical-biological coupling occurs in warm-core eddies, particularly since no study has examined the relationship between bacteria and viruses. The purpose of the present study was to examine the influence of anticyclonic warm eddy on the relationship between bacterial and viral abundances as well as viral activity (viral production) in different depths. In the core of warm eddy, bacterial abundance (0.48 to 2.82 ×105 cells mL−1) fluctuated less than that of the outside eddy (1.12 to 7.03×105 cells mL−1). In particular, there was four-folds higher of viral-bacterial abundance ratio (VBR) estimated within the eddy below DCM than the outside eddy. We suggest that prevailing physical forces with downwelling at the center of the anticyclonic warm eddy, viruses can also be transmitted into the deep ocean directly through adsorption on particulate organic matter during sinking. Overall, our findings provide valuable insights into the interaction between bacterial and viral communities and their ecological mechanism within the warm eddy.

Theoretical physics addresses the fundamental principles of nature and the mysteries of the universe. In the last century, the theory of relativity challenged people's understanding of time and space, while quantum mechanics revealed various forms of energy. However, the concept of gravity remains elusive. All matter in the universe is composed of energy that can be converted into other forms, yet it is always conserved. However, achieving a state of equilibrium, represented by the equal sign, can be challenging to achieve on both macro and quantum scales. A phenomenon that can transition from one state to infinity is called collision and is essential for understanding natural phenomena and physical processes throughout the universe. In the study of general relativity cannot be three-dimensional problems to gain mathematical inspiration, understand the application of new dimensions. Here, we elucidate the nature of gravity, which inspires the solution of the Riemann hypothesis. Our results show that the conduction mode of dimensional energy is defined by Euler's formula. And a special mode of collision is derived which translates into vibration.

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

This paper intoduces a non-standard research technique to clarify how complex phenomena, such as those that are abundantly present in human physiology, can be faithfully described using fractal dynamical models with and without stochastic forces. This method for conducting research involves tracing the his- torical evolution of understaning an empirical medical process faciltated by the fractal calculus perspective. Herein we trace the analysis of the time series for heart rate varability (HRV) developed for diagnosing the cardiovascular health of a patient. This is done herein by introducing four (one empirical which en- tails three theoretical fractal models) distinct but related fractal models each one introduced to solve a particular problem arising from a fundamental defect in the previous model but in generalizing a model at one stage to resolve the problem associated with the defect another is invariably introduced by the re- placement model. It is through the utilization of the fractional calculus that the necessity for rethinking how to systematically incorporate additonal layers of complexity are revealed ultimately resulting in a 'complete' description of its empirical dynamics in fractal terms.

Although effective in term of chance of future live birth, the current methods for fertility preservation such as oocytes, embryo or ovarian tissue cryopreservation cannot be offered to all cancer patients and in all clinical contexts. Expanding options for fertility preservation is crucial to address the need to encompass all situations. One emerging strategy is pharmacoprotection, which is non-invasive and has the potential to fill existing gaps in fertility preservation. Besides the identification of the most efficient therapeutic agent itself, the potential off-target effect re-mains one of the main limitation of this strategy for clinical application, particularly when healthy ovarian tissue is targeted. This review focuses on the advances in pharmacoprotective approaches and the challenge of targeting the ovaries to deliver these agents. The unique properties of gold nanoparticles (AuNPs) make them an attractive candidate for this purpose. We discuss how AuNPs meet many of the requirements for an ideal drug delivery system, as well as the existing limitations that have hindering the progression of AuNPs research into more clinical trials. Additionally, the review highlights microRNA (miRNA) therapy as a next-generation approach to address the issues of fertility preservation and discusses the obstacles that currently impede its clinical availability.

Cymbidium faberi Rolfe is one of the traditional Chinese orchids with important ornamental value, and the cultivation of Cymbidium faberi Rolfe mutant strains with different appearances is essential to increase its economic value, but at present, the acquisition of Cymbidium faberi Rolfe mutant strains basically relies on natural mutation.The objectives of this research were to mutagenize Cymbidium faberi Rolfe protocorm-like bodies (PLBs) and shoots in vitro using sodium azide (NaN3), and to screen and evaluate mutants in mutagenized Cymbidium faberi Rolfe seedlings using morphological characteristics.Cymbidium faberi Rolfe PLBs and shoots were used as mutagenic materials, and co-cultivated in induced shoots growth medium with the addition of 0.0 (control), 0.5, 1.0, 1.5, 2.0, 2.5, 3.0 mg/L and 0.0 (control), 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, and 10.0 mg/L NaN3 to induce the mutations, and the mortality rates of the PLBs and shoots were increased with the increase of the NaN3 concentration.At 14 d of co-cultivation, PLBs and shoots were most efficiently mutagenized with 1.5 mg/L and 4.0 mg/L NaN3, respectively.After the explants were cultured for 3 months, changes in leaf and flower morphology were observed in some mutants: shorter and thicker leaves, shorter node length, reduced height, and mid-translucent leaves compared with controls; and some Cymbidium faberi Rolfe bloomed prematurely, with single flowers with large, thick petal sepals and small inflorescences, and colours include light green throughout, and a few with purple stamens.This suggests that NaN3 can effectively mutagenise Cymbidium faberi Rolfe PLBs and shoots to satisfy people's demand for Cymbidium faberi Rolfe's ornamental properties while increasing its economic value.

Blood image intensity has been used to detect erythrocyte sedimentation rate (ESR). However, it does not give an information on biophysical properties of blood sample under continuous ESR. In this study, three physical properties, including, τ₀, ESR_τ, and AI_I, are suggested to quantify mechanical variations of blood under continuous ESR. To demonstrate the proposed method, blood sample is loaded into a driving syringe. The blood flow rate is set in a periodic on–off pattern. Blood sample is then supplied into a capillary chip, and microscopic blood images are captured at specific intervals. Blood shear stress is quantified from the interface of blood stream in the coflowing channel. Both τ₀ and ESR_τ are then obtained by analyzing the blood shear stress. Simultaneously, the AI_I is evaluated by analyzing the image intensity of blood flow. According to the experimental results, the τ₀ exhibits consistent trends with respect to hematocrit as well as diluent. The ESR_τ and AI_I showed a reciprocal relationship each other. Three suggested properties represented substantial differences for suspended blood samples (i.e., hardened red blood cells, different concentration of dextran solution and fibrinogen). In conclusion, the present method can detect variations of blood sample under continuous ESR effectively.

Educating children to be informed, responsible, socially adept citizens who care about others is an overarching purpose for schools. A rising variety of preventive and child development initiatives are being implemented in schools. Insufficient coordination with other school activities and neglect of implementation and assessment variables essential for a significant program impact these programs' current implications. They are not doomed to failure in the long term. The other challenges for scholars in school-based action research are identifying practical models to prevent problem characteristics, promoting positive child development, and supporting widespread development and sustainability of evidence-based preschool through educational practice. To conceptualize good youth development programs through Social and Emotional Learning (SEL) in schools, this research presents integrated social, emotional, and intellectual education (ISEIE). School interventions are necessary to implement the social and emotional skills on self-understanding, social knowledge, self-management, relationship management, responsibility, and decision-making. Schools are the best place to implement all these programs to create a better generation. To back up this viewpoint, this study looks at research from illustrative studies and research syntheses. In the end, this paper provides suggestions for implementing programs that combine social, emotional, and intellectual development.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

Searching over a sorted list is a classical problem in computer science. Binary Search takes at most log2n+1 tries to find an item in a sorted list of size n. Interpolation Search achieves an average time complexity of Ο(loglogn) for uniformly distributed data. Hybrids of Binary Search and Interpolation Search are also available to handle data with unknown distributions. This paper analyzes the computation cost of these methods and shows that interpolation can significantly affect their performance — accordingly, a new method, Interpolation Once Binary Search (IOBS), is proposed. The experimental results show that IOBS outperforms the hybrids of Binary Search and Interpolation Search for nonuniformly distributed data.

The α-glucosidase inhibitor is of interest to researchers due to its association with type-II diabetes treatment by suppressing postprandial hyperglycemia. Hesperidin is a major flavonoid in orange fruit with diverse biological properties. This paper evaluates the effects of hesperidin on α-glucosidase through inhibitory kinetics, fluorescence quenching, and molecular docking methods for the first time. The inhibition kinetic analysis showed that hesperidin reversibly inhibited the α-glucosidase activity with an IC50 value of 18.52 M and the inhibition was performed in an uncompetitive type. Fluorescence quenching studies indicated that the intrinsic fluorescence of α-glucosidase was quenched via a static quenching process and only one binding site was present between hesperidin and α-glucosidase. The interaction between them was spontaneous and mainly driven by hydrogen bonds as well as hydrophobic forces. Furthermore, molecular docking results suggested that hesperidin might bond to the entrance or outlet part of the active site of α-glucosidase through a network of five hydrogen bonds formed between hesperidin and the four amino acid residues (Trp709, Arg422, Asn424, and Arg467) of ?-glucosidase and hydrophobic effects. These results provide new insights into the inhibitory mechanisms of hesperidin on α-glucosidase, supporting the potential application of hesperidin-rich orange product as a hypoglycemic functional food.

Tack is one of the most important factors affecting the operability of prepregs, but it is still very difficult to obtain the change of prepreg tack with time at different temperatures. In this paper, a newly designed T-peel device is used to test the tack decay rate of prepregs at different temperatures. The obtained decay rate deviates less than 8.9% from the manufacturer's data. The maximum deviation of the ratio of tack decay speeds calculated by the Arrhenius equation from the experiments is not higher than -9.7%. It is proved that the present method can obtain the decay rate of tack of prepregs at different temperatures. This method is also applicable to the other two types of prepregs. The article proposes the handling life unit, an operational life measurement unit for prepregs, and establishes that the relationship between tack and remaining shelf life reduces prepreg management costs.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

Cortex Periplocae, as a traditional Chinese herbal medicine, has been widely used for autoimmune diseases, especially rheumatoid arthritis. Due to its potential pharmaceutical values, more studies about the biological activities of Cortex Periplocae have been conducted recently. Meanwhile, the adverse reaction of Cortex Periplocae is not a negligible problem in clinic. In this article, we reviewed a series of articles and summarized the recent studies of Cortex Periplocae in the areas of phytochemistry and pharmacology. More than 100 constituents have been isolated and identified from Cortex Periplocae, including steroids, cardiac glycosides, terpenoids, and fatty acid compounds. The crude extracts of Cortex Periplocae and its active compounds exhibit various biological activities, such as cardiotonic effect, anticancer action, and anti-inflammatory effect. This paper aims to provide an overall review on the bioactive ingredients, pharmacological effect, and toxicity of this plant. Furthermore, this review suggests investigating and developing new clinical usages according to the above pharmacological effects.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

The multidrug resistance transporter NorM is an important drug resistance pump and plays a critical role in multidrug resistance in bacteria and mammals. In this study we carried out molecular dynamics simulation to study the mechanism of Na+ binding and dynamical structures of two long loops in the substrate-releasing process in substrate binding NorM. Our simulation study identified several key residues (D41, E261 D377) along the Na+ binding pathway and a multi-state ion-binding mechanism is proposed based on the simulation study. In this proposed model, the transport of Na+ is a multi-stage process with D41 being the first station for binding to Na+, followed by Na+ binding to the second station E262 and finally to the cation-binding site of E262 and D377. During the transport of Na+, the transmembrane components TM1, TM7 and TM2 are rearranged to facilitate the ion transport as well conformational changes of NorM to a closed state. Further, substrate-bound simulation revealed that Loop3-4 and Loop9-10 control the substrate-releasing process.

Stabilization of a G-quadruplex (G4) in the promotor of the c-MYC proto-oncogene leads to inhibition of gene expression, and it thus represents a potentially attractive new strategy for cancer treatment. However, most G4 stabilizers show little selectivity among the many G4s present in the cellular complement of DNA and RNA. Intriguingly, a crescent-shaped cell-penetrating thiazole peptide, TH3, preferentially stabilizes the c-MYC G4 over other promotor G4s, but the mechanisms leading to this selective binding remain obscure. To investigate these mechanisms at the atomic level, we performed an in silico comparative investigation of the binding of TH3 and its analogue TH1 to the G4s from the promotors of c-MYC, c-KIT1, c-KIT2, and BCL2. Molecular docking and molecular dynamics simulations, combined with in-depth analyses of non-covalent interactions and bulk and per-nucleotide binding free energies, revealed that both TH3 and TH1 can induce the formation of a sandwich-like framework through stacking with both the top and bottom G-tetrads of the c-MYC G4 and the adjacent terminal capping nucleotides. This framework produces enhanced binding affinities for the c-MYC G4 relative to other promotor G4s, with TH3 exhibiting an outstanding binding priority. Van der Waals interactions were identified to be the key factor in complex formation in all cases. Collectively, our findings fully agree with available experimental data. Therefore, the identified mechanisms leading to specific binding of TH3 towards the c-MYC G4 provide valuable information to guide the development of new selective G4 stabilizers.

Due to their high specificity, monoclonal antibodies (mAbs) have garnered significant attention in recent decades, with advancements in production processes, such as high seeding density (HSD) strategies, contributing to improved titers. This study provides a thorough investigation of high seeding processes for mAb production in Chinese hamster ovary (CHO) cells. Using a metabolic network and flux balance analysis, we compared standard fed-batch (STD FB) with HSD cultivations, exploring supplementary lactate and cysteine, and a bolus medium enriched in amino acids. We observed high glycolytic fluxes and depletion of asparagine simultaneously with the lactate shift building kinetic models around this and other observations. An ensemble of kinetic models assessed the impact of a feeding medium enriched with additional asparagine, revealing a missing lactate shift without enhancing mAb productivity in the experiments. This research provides valuable model-based insights into cellular metabolism during HSD processes, laying the foundation for refined CHO cell-based mAb production. The proposed hypothesis on the regulations guides future experimental validation and bioprocess optimization for enhanced mAb production efficiency.

Agrivoltaic agrotunnels are currently designed for high density grow walls that are not amenable to bush berries or root crops. Commercial grow bins provide deeper substrates for produce with more root systems but have high costs per unit growing area. To overcome the economic limitations of grow bins, this study applies the distributed manufacturing open-source design paradigm to develop four designs for low-cost open source structures. The designs target root vegetables and bush fruit specifically to be adopted by remote communities with limited or no outdoor growing environment to offset the market price for imported fresh produce. The indoor growing designs provide the necessary structure for supporting grow light and grow bins and enabled the transplanted berry plants to flower and produced fruits. They provide a comparable amount (110L) or more of grow volume from 106 to 192 L. The water reservoir volume for the commercial system (62 L) and grow area (0.5 m³) is surpassed by all new designs that range from 64 to 192 L and 0.51 to 0.76 m³, respectively. These superior properties are possible with material costs for all four designs that save more than 90% of the economic cost of the commercial systems.

The age-related loss of muscle mass and strength is referred to as “sarcopenia”. The combined effect of sarcopenia and osteoporosis is a devastating threat to the old adult, accounting for reduced mobility, risk for falls and subsequent fractures. In previous studies, we observed a high degree of inter-individual variability of paraspinal muscle fatty infiltration, one most relevant index of muscle wasting. This aspect solicited us to develop a computerized method to quantitatively characterize muscle fatty infiltration in aging and diseases. Magnetic resonance images of paraspinal muscles from 58 women of different age (age range 23-85 years) and physio-pathological status (healthy young, pre-menopause, post-menopause, and os-teoporosis), were used to set up the method. It is based on fractal analysis of lean muscle area (contractile muscle) to estimate muscle fatty infiltration. In particular, lacunarity was computed by parameter β from our hyperbola model function, used to fit the GBA (gliding box algorithm) curvilinear plot. Succolarity was estimated by parameter µ, for the four main directions, through an algorithm implemented on purpose. Results show that fractal lacunarity, by quantifying muscle fatty infiltration, can discriminate be-tween osteoporosis and healthy aging while succolarity can separate the other three groups showing similar lacunarity. Therefore, fractal features of contractile muscle, by measuring fatty infiltration, can represent good indices of sarcopenia in aging and disease.

The Soil and Water Assessment Tool (SWAT) is one of the most widely used hydrologic models. SWAT has been undergoing constant changes since its development. However, compartment review and testing of SWAT are comparably limited, especially the flood routing functions. In this study, the daily flood routing subroutines of different SWAT versions were reviewed and tested using a well observed segment of the Weser river located in Germany. Results show several problems with the flood routing subroutines of SWAT. The variable storage subroutine of SWAT (revision 664) does not transform the flood wave. Unphysical results could be obtained with the variable storage routing of SWAT (revision 528). The Muskingum subroutine of SWAT (revisions 664 and 528) overestimates channel evaporation (resulting in a bias of 14\% to 19% in streamflow) and underestimates transmission losses. Simulated results show that the timing and shape of the flood wave could be improved with a corrected Muskingum subroutine. Based on the results of this study, we suggest the SWAT user community to review their existing SWAT models to see how the aforementioned issues will affect their methods, findings and conclusions.

MultiCal is an affordable, high-precision measuring device designed for the on-site calibration of industrial robots. Its design features a long measuring rod with a spherical tip that is attached to the robot. By restricting the rod’s tip to multiple fixed points under different rod orientations, the relative positions of these points are accurately measured beforehand. A common issue with MultiCal is the gravity deformation of the long measuring rod, which introduces measurement errors into the system. This problem becomes especially serious when calibrating large robots, as the length of the measuring rod needs to be increased to enable the robot to move in a sufficient space. To address this issue, we propose two improvements in this paper. Firstly, we suggest the use of a new design of the measuring rod that is lightweight yet has high rigidity. Secondly, we propose a deformation compensation algorithm. Experimental results have shown that the new measuring rod improves calibration accuracy by 20% to 39%, while by using the deformation compensation algorithm, the accuracy increases by 6% to 16%. In the best configuration, the calibration accuracy is similar to that of a measuring arm with a laser scanner, producing an average positioning error of 0.274 mm and a maximum positioning error of 0.838 mm. The improved design is cost-affordable, robust, and has sufficient accuracy, making MultiCal a more reliable tool for industrial robot calibration.

Water plays a vital role in the healthy growth of pears. Early detection of water stress can play a significant role in the timely management of water deficiency for pear yield. Most current methods are labour-intensive, time-consuming, only provide point measurements, and could be destructive. In this research, a real-time non-destructive method using a push-broom hyperspectral system (400-1000nm) was used to collect hyperspectral image data and detect the water stress of the pear seedling leaves. To build a reliable prediction model, machine learning techniques were used. The Successive Projections Algorithm (SPA) was applied for optimal wavelength selection. In particular, CNN was applied to obtain the features of key wavelengths. Both the CNN features and key wavelengths were put into RR-MLR, BLR and ENN for analysis. The training accuracy of the three modellings all reach the accuracy above 70% after about 100 epochs, while combination of CNN features outperformed the mere main spectra analysis. This research demonstrated that hyperspectral imaging coupled with machine learning techniques could be applied to predict the water content of pear leaves predict non-destructively.

It is crucial to forecast the water demand accurately for supplying water efficiently and stably in a water supply system. In particular, accurately forecasting short-term water demand helps in saving energy and reducing operating costs. With the introduction of the Smart Water Grid (SWG) in a water supply system, the amount of water consumption is obtained in real time through an advanced metering infrastructure (AMI) sensor, which can be used for forecasting the short-term water demand. The models widely used for water demand forecasting include the autoregressive integrated moving average, radial basis function-artificial neural network, quantitative multi-model predictor plus, and long short-term memory. However, there is a lack of research on assessing the performance of models and forecasting the short-term water demand by applying the data on the amount of water consumption by purpose and the pipe diameter of an end-use level of the SWG demonstration plant in each demand forecasting model. Therefore, in this study, the short-term water demand was forecasted for each model using the data collected from the AMI, and the performance of each model was assessed. The Smart Water Grid Research Group installed ultrasonic-wave-type AMI sensors in the block 112 located in YeongJong Island, Incheon, and the actual data used for operating the SWG demonstration plant were adopted. The performance of the model was assessed by using the residual, root mean square error (RMSE), normalized root mean square error (NRMSE), Nash–Sutcliffe efficiency (NSE), and Pearson correlation coefficient (PCC) as indices. The water demand forecast was slightly underestimated in models that employed the assessment results based on the RMSE and NRMSE. Furthermore, the forecasting accuracy was low for the NSE due to a large number of negative values; the correlation between the observed and forecasted values of the PCC was not high, and it was difficult to forecast the peak amount of water consumption. Therefore, as the short-term water demand forecasting models using only time and the amount of water consumption have limitations in reflecting the characteristics of consumers, a water supply system can be managed more precisely if other factors (weather, customer behavior, etc.) influencing the water demand are applied.

This research focussed on utilisation of salmon protein and lipid to manipulate pasta glycaemic index and protein digestibility. Salmon fish (Oncorhynchus tschawytscha) powder (SFP) supplemented pasta flour at the from 5% to 20% (w/w). Inclusion of SFP lead to a significant reduction in starch digestibility and hence the potential glycaemic values of pasta (experimental pasta being up to 143% lower than control values). SFP addition to pasta increased the release of phenolic compounds from pasta during both a gastric digestion (179%) and pancreatic digestion ( 133%) in comparison to the control sample. At the same time, the antioxidant activity of the digested pasta was increased by up to 263% (gastric) and 190% (pancreatic) in comparison to durum wheat pasta alone. Interestingly, although protein levels increased with incorporation of SFP, the digestibility values of the protein decreased from 86.41% for the control pasta to 81.95% for 20% SFP pasta. This may indicate that there are interactions between phenolic and protein in the pasta samples which affect overall protein digestibility levels.

Oleuropein, glycosylated secoiridoid present in olive leaves is known to be an important antioxidant phenolic compound. We studied the antioxidant effect of low doses of oleuropein aglycone (3,4-DHPEA-EA) and oleuropein aglycone peracetylated (3,4-DHPEA-EA(P)) in murine C2C12 myocytes treated with hydrogen peroxide (H2O2). Both compounds were used at a concentration of 10 μM and were able to inhibit cell death induced by the H2O2 treatment, with 3,4-DHPEA-EA(P) being more. Under our experimental conditions, H2O2 efficiently induced the phosphorylated-active form of JNK and of its downstream target c-Jun. We demonstrated, by Western blot analysis, that 3,4-DHPEA-EA(P) was efficient in inhibiting the phospho-active form of JNK. This data suggests that the growth arrest and cell death of C2C12 proceeds via the JNK/c-Jun pathway. Moreover, we demonstrated that 3,4-DHPEA-EA(P) affects the myogenesis of C2C12 cells; because MyoD mRNA levels and the differentiation process are restored with 3,4-DHPEA-EA(P) after treatment. Overall, the results indicate that 3,4-DHPEA-EA(P) prevents ROS-mediated degenerative process in a genomic and epigenomic manner by functioning as an efficient antioxidant.

Oleuropein, glycosylated secoiridoid present in olive leaves is known to be an important antioxidant phenolic compound. We studied the antioxidant effect of low doses of oleuropein aglycone (3,4-DHPEA-EA) and oleuropein aglycone peracetylated (3,4-DHPEA-EA(P)) in murine C2C12 myocytes treated with hydrogen peroxide (H2O2). Both compounds were used at a concentration of 10 μM and were able to inhibit cell death induced by the H2O2 treatment, with 3,4-DHPEA-EA(P) being more. Under our experimental conditions, H2O2 efficiently induced the phosphorylated-active form of JNK and of its downstream target c-Jun. We demonstrated, by Western blot analysis, that 3,4-DHPEA-EA(P) was efficient in inhibiting the phospho-active form of JNK. This data suggests that the growth arrest and cell death of C2C12 proceeds via the JNK/c-Jun pathway. Moreover, we demonstrated that 3,4-DHPEA-EA(P) affects the myogenesis of C2C12 cells; because MyoD mRNA levels and the differentiation process are restored with 3,4-DHPEA-EA(P) after treatment. Overall, the results indicate that 3,4-DHPEA-EA(P) prevents ROS-mediated degenerative process in a genomic and epigenomic manner by functioning as an efficient antioxidant.

Background: Transit-time flow measurement (TTFM) is frequently used to evaluate intraoperative quality control during coronary artery bypass grafting (CABG). Although TTFM has the ability to assess graft failure intraoperatively, the perioperative factors affecting TTFM during CABG surgery remain poorly understood. Methods: Patients who underwent CABG surgery at a single institution between July 2016 and May 2018 were prospectively evaluated. Patients’ demographic characteristics, previous medical history, Euroscore, the results of preoperative blood tests, and intraoperative data were recorded. TTFM and blood viscosity were measured hemodynamically, and mean flow (mL/min) and pulsatility index (PI) were recorded. Arterial blood gas was analyzed immediately after anastomosis of the left internal mammary artery (LIMA) to the left descending artery (LAD) and before sternal closure. Factors associated with TTFM were assessed by multiple linear regression analysis. Results: Of the 62 patients who underwent CABG surgery during the study period, 57 were evaluated, including 49 who underwent off-pump and eight who underwent on-pump surgery. Blood viscosity was not significantly associated with TTFM (p > 0.05). However, TTFM was significantly associated with body mass index (BMI), systolic blood pressure, and cardiac index (p < 0.05 each). Conclusions: Blood viscosity was not significantly associated with intraoperative graft flow. Blood flow of graft vessels, however, was significantly associated with BMI, systolic blood pressure, and cardiac index.

In South Korea, in line with the increasing need for a reliable water supply following the continuous increase in water demand, the Smart Water Grid Research Group (SWGRG) was officially launched in 2012. With the vision of providing water welfare at a national level, SWGRG incorporated information and communications technology in its water resource management, aiming at the development of core technologies for a Smart Water Grid consisting of intelligent microgrids and a demonstration and tests of the developed technologies through a field operation in a living lab. The living lab was built in Block 112 of YeongJong Island, Incheon, South Korea (area of 17.4 km2, population of 8,000), where Incheon International Airport, a hub of Northeast Asia, is located. In this location, water is supplied through a single submarine pipeline, making the place optimal for responses to water crises and the construction of a water supply system during emergencies. From 2017 to 2019, ultrasonic wave type smart water meters and IEEE 802.15.4g advanced metering infrastructure (AMI) networks were installed at 527 sites of 958 consumer areas in the living lab, and core element technologies (intelligent water source management and distribution system, smart water distribution network planning/control/operation strategy establishment, AMI network and device development, integrated management of bi-directional smart water information), and operation solutions (smart water statistics information, real-time demand-supply analysis, decision support system, real-time hydraulic pipeline network analysis, smart DB management, and water information mobile application) were developed through a field operation and testing.