Blood testing is a crucial medical application. In this study, we applied Raman spectroscopy to test blood samples and obtained complete biological information, including the main components and compositions in these samples. Short-wavelength (532-nm green light) Raman scattering spectroscopy was conducted on samples of normal blood, abnormal blood in 3 types of preparation including whole blood, plasma, and serum, and the underlying information reflected by the biological characteristics detected in each sample type were analyzed. Raman spectroscopy results indicated that normal blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. Hemoglobin affects blood oxygen level. The characteristic peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. In addition, surface-enhanced Raman spectroscopy was used to collect biological signals that are difficult to obtain in conventional Raman spectroscopy, including those of small molecules such as hormones, antibodies, and enzymes. Changes in biological information collected in this manner can be used as a basis for potentially diagnosing clinical diseases.

A robust guaranteed cost preview repetitive controller is proposed for a class of polytopic uncertain discrete-time systems. In order to improve the tracking performance, the repetitive controller combined with preview compensator is inserted in the forward channel. By using the L-order forward difference operator, an augmented dynamic system is constructed. Then, the guaranteed cost preview repetitive control problem is transformed into the guaranteed cost control problem for the augmented dynamic system. For given performance index, the sufficient condition of asymptotic stability for the closed-loop system is derived by combining parameter-dependent Lyapunov function method with linear matrix inequality (LMI) techniques. By incorporating the controller obtained into the original system, the guaranteed-cost preview repetitive controller is derived. A numerical example is also included to show the effectiveness of the proposed method.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

To determine the fracture rate of ceramic crowns and causes of ceramic crown failure, this study used keywords—namely “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown”—to search for articles published in English from 2005 to 2023 in the PubMed electronic database. Rather than using the Boolean logic algorithm between MESH terms and keywords, we accurately calculated the numbers of final clinically tracked cases with crown fractures from the contents of articles. The titles and abstracts of many related articles focused on implant or abutment fracture, while crown fracture was investigated and mentioned only in the main texts of the articles. Our studies included those crowns as well as having more complete data collection. Our search yielded 228, 93, 404, and 358 articles for the keywords “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown,” respectively. We used the Newcastle–Ottawa Scale (NOS) to assess article quality, and our inclusion criteria were randomized controlled trials (RCT) and cohort study articles involving more than 3 years of follow-up and more than 20 cases. After reviewing, 16 high-quality articles were selected for analysis. The 4.4% crown fracture rate recommended on the basis of most clinical results was achieved in only 6 of the 16 articles. In these 6 articles, the researchers concluded the following reasons that may cause the crown fractures: the thickness of the veneer ceramic material; the connector dimensions; pontic span of the fixed prosthesis; the type of cement; the treatment of the ceramic surface before luting. Other articles inferred that the computer-aided design libraries that were insufficient for the creation of appropriate anatomically supported frameworks for prostheses with ceramic veneers; the thermal expansion coefficient and fracture toughness of the framework material did not match those of the veneer ceramic, resulting in an insufficient area supporting the ceramic veneer then leads to premature crown failure after a long period chewing. The future prospective for material developing could focus on solving those problems and have better clinical results.

Evaluating soil quality across various altitudinal gradients, both with and without vegetative cover, is crucial for the proper functioning of soil and optimal crop growth, thereby contributing to the sustainability of agroecosystems. Although the altitudinal gradient significantly influences soil quality, the ability to predict this quality, expressed through an index, in soils with and without vegetative cover, is still insufficiently explored. This study aimed to assess soil quality in the Jun Jun micro-watershed, located in the Tungurahua region, Ecuador. To achieve this objective, three categories of altitudinal gradients were selected: less than 2800 meters above sea level (masl), between 2800 and 2900 masl, and greater than 2900 masl. A total of 24 soil samples were collected in the mentioned gradients, considering both areas with and without vegetative cover. The indicators used included chemical and biological parameters such as soil organic carbon (OC), earthworm density (WD), earthworm biomass (WB), organic matter (OM), pH, total nitrogen (TN), and organic carbon (OC). The results revealed that in areas with altitudinal gradients below 2800 masl, soil quality index values were higher compared to other altitudes. In vegetated areas, a decrease in index values was observed as the altitudinal gradient increased, indicating a deterioration in soil quality with altitude. These findings are significant in providing a quantitative assessment of the effects of altitudinal gradient and vegetative cover influence on soil quality.

Knowledge graphs (KGs) play a crucial role in many applications, such as question answering, but incompleteness is an urgent issue for their broad application. Much research in knowledge graph completion (KGC) has been performed to resolve this issue. The methods of KGC can be classified into two major categories: rule-based reasoning and embedding-based reasoning. The former has high accuracy and good interpretability, but a major challenge is to obtain effective rules on large-scale KGs. The latter has good efficiency and scalability, but it relies heavily on data richness and cannot fully use domain knowledge in the form of logical rules. We propose a novel method that injects rules and learns representations iteratively to take full advantage of rules and embeddings. Specifically, we model the conclusions of rule groundings as 0-1 variables and use a rule confidence regularizer to remove the uncertainty of the conclusions. The proposed approach has the following advantages: 1) It combines the benefits of both rules and knowledge graph embeddings (KGEs) and achieves a good balance between efficiency and scalability. 2) It uses an iterative method to continuously improve KGEs and remove incorrect rule conclusions. Evaluations on two public datasets show that our method outperforms the current state-of-the-art methods, improving performance by 2.7% and 4.3% in mean reciprocal rank (MRR).

Image segmentation is a new challenge prob- lem in medical application. The use of medical imaging has become an integral part of research, as it allows us to see inside the human body without surgical intervention. Many researcher have studied brain segmentation. One stage method is used to segment the brain tissues. In this paper, we proposed the multi-stage generative ad- versarial network to solve the problem of information loss in the one-stage. We utilize the coarse-to-fine to improve brain segmentation using multi-stage generative adversar- ial networks (GAN). In the first stage, our model generated a coarse outline for (i) background and (ii) brain tissues. Then, in the second stage, the model generated outline for (i) white matter (WM), (ii) gray matter (GM) and (iii) cerebrospinal fluid (CSF). A good result can be achieved by fusing the coarse outline and refine outline. We conclude that our model is more efficient and accu- rate in practice for both infant and adult brain segmenta- tion. Moreover, we observe that multi-stage model is faster than prior models. To be more specific, the main goal of multi-stage model is to see the performance of the model in a few shot learning case where a few labeled data are available. For medical image, this proposed model can work in a wide range of image segmentation where the convolution neural networks and one-stage methods have failed.

With the increase of intelligent voice phishing and the increasing reliance on open banking systems, there has been a rise in cases where individuals' personal information has been exposed, resulting in significant financial losses for the victims. Non-face-to-face transactions in the financial sector face challenges such as customer identification, ensuring transaction integrity, and preventing transaction rejection. Blockchain-based distributed ledgers have been proposed as a solution, but their adoption is limited due to the difficulty of managing private keys and the burden of gas fees management. This paper proposes a non-face-to-face P2P real-time token payment system that minimizes the risk of key loss by storing private keys in a keystore file and database through a server-based key management module. The proposed system simplifies token creation and management through a server-based token management module and implements an automatic gas charging function for smooth token transactions. Transaction integrity and non-repudiation are ensured through a transaction confirmation module that uses transaction IDs without exposing personal information. Furthermore, advanced security measures such as blocking foreign IP access and DDoS defense are implemented to securely protect user data. The proposed system aims to provide a convenient, secure, and accessible online payment solution to the public by implementing a self-authentication function using a web application that is not limited to smart phones or application platforms.

The teaching and learning environment have changed significantly over the last decade with the integration of an increasing amount of information and communication technologies, especially in distance education due to global pandemics, total lockdowns, isolation, and quarantine periods. The number of numerous virtual and non-virtual tools involved in educational processes is growing day by day. In terms of technological innovations used in learning environments, many researchers and educators are trying their best to bring more creative ideas into the technology- based learning environments. Although higher educational institutions have greatly benefited from the growing number of hardware and software resources in the educational process, they have also faced some setbacks that have harmed the learning processes. These technologies have in turn complicated some of the processes in the learning atmosphere. Therefore, we take Spanish teaching course as an example to present the challenging smarter teaching and learning systems that higher educational institutions face today.

Building on the Sustainable Happiness Model, this study examined how congruency between ideal self-image and brand image influence a sense of happiness. The findings show that when ideal self-image and ideal social self-image are congruent with brand image a sense of happiness can be enhanced through brand identification and positive emotions. This study contributes to literature as it reveals the mechanism of how congruency between ideal self-image and brand image positively affect happiness.

Recently many researches of EOS (Electric Arc Furnace Oxidizing Slag) on application to construction industry have been carried out with increasing its production and limited reclamation site. EOS can be used as a fine aggregate for construction material, however, its engineering properties vary with the manufacturing process and producing district, causing a quality differences in material performance. In the work, EOS is obtained from steel manufacturing plants in South Korea and the engineering properties are evaluated for EOS and the cement mortar with EOS, respectively. From the tests, EOS is mainly made up of CaO, SiO₂, and FeO with 18.2% of larnite which has a crystal structure of β-C₂S with similar cement mineral. EOS mortar shows an increasing compressive strength with more EOS content, which is affected by a considerable amount of larnite (β-C2S) in EOS. The EOS based mortar with ERS (Electric Arc Furnace Reduction Slag) shows unsatisfactory results over the criteria for rate of change, which implies that more consideration must be taken for the usage of the mixed ERS and EOS for cement mortar due to swelling effect of ERS on dimensional stability.

Refractive index measurements have been an important task for a long time because that index plays an essential role in describing the optical properties of a material. Many methods have been developed to perform that task. Some of them use interferometry to achieve high precision, however these configurations are complicated. Some measure the critical angle using simple structures, but the accuracy is not satisfactory because it is difficult to judge the exact critical angle with intensity variations. Here we propose several new schemes based on measuring the polarization change in the total internal reflection. The proposed method has the merits of simple structure and easy incident angle determination that gives the maximum phase change. Additionally, it is possible to find the material dispersion by measuring the wavelength dependence of the polarization ellipticity. Some useful formulas relating the refractive index with the maximum phase change are obtained. This work can provide valuable alternatives for index measurement.

Wastes from social economic activities had great impact on water quality thereby limiting water usability for domestic purposes. Sewages discharge from people activities, usually consist of undesirable concentrations of soluble chemicals that infiltrate into the surrounding surface and underground water, and then constitute health risk to the populace. In order to investigate the concentration characteristics and health risk for the local residents in Nandong Underground River Watershed (NURW), eleven common heavy metals in the water body analysis were conducted. Health risk assessment (HRA) was taken to analyze eleven heavy metals of 84 water samples from surface and underground waters in NURW: 36 samples underground water and 48 samples surface water. Our results showed that the heavy metals concentration order is that of Fe > Al > Mn > Zn > As > Cd > Pb > Cr > Ni > Cu > Hg. Correlation analysis indicates that these eleven metal elements have certain similarity on material source and migration transformation. The health risks for local residents exposed to metal elements in the water of NURW mainly from carcinogenic risk (10−6～10−4 a−1) through drinking way, and the health risk of heavy metals exposed to children through drinking way was much higher than adults. The maximum exposing health risks of Cr in both underground and surface water were higher than the recommendation standard (5.0×10-5 a-1) from ICRP, and all the values over the standard (5.0×10-6 a-1) recommended by the Swedish Environmental Protection Agency and the Dutch Ministry of Construction and Environment and the British Royal Society. The results of health risk assessment shows that Cr in the water of NURW was the mainly source of carcinogenic risk for the local residents, following by Cd and As. Consequently, it is necessary to control the three carcinogenic metals when the water was used as drinking water source.

Translation is spatiotemporally regulated and ER-associated mRNAs are generally in efficient translation. It is unclear whether the ER-associated mRNAs are deadenylated or degraded on the ER surface in situ or in the cytosol. Here, we showed that ER possessed active deadenylases, particularly the poly(A)-specific ribonuclease (PARN), in common cell lines and mouse tissues. Consistently, purified recombinant PARN exhibited a strong ability to insert into the Langmuir monolayer and liposome. ER-anchored PARN was found to be able to reshape the poly(A) length profile of the ER-associated RNAs by suppressing long poly(A) tails without significantly influencing the cytosolic RNAs. The shortening of long poly(A) tails did not affect global translation efficiency, suggesting that the non-specific action of PARN towards long poly(A) tails was beyond the scope of translation regulation on the ER surface. Transcriptome sequencing analysis indicated that the ER-anchored PARN trigged the degradation of a small subset of ER-enriched transcripts. The ER-anchored PARN modulated the translation of its targets by redistributing ribosomes to heavy polysomes, suggesting that PARN may play a role in dynamic ribosome reallocation. During DNA damage response, MK2 phosphorylated PARN-Ser557 to modulate PARN translocation from the ER to cytosol. By promoting the decay of ER-associated MDM2 transcripts with low ribosome occupancy, the ER-anchored PARN modulated DNA damage response and thereby cell viability. These findings revealed that a highly regulated communication between mRNA degradation rate and translation efficiency is present on the ER surface in situ and that PARN may contribute to this communication by modulating the dynamic ribosome reallocation between transcripts with low and high ribosome occupancies.

In autonomous driving systems, high-speed and real-time image processing, along with object recognition, are crucial technologies. This paper builds upon the research achievements in in-dustrial item sorting systems and proposes an object recognition and sorting system for auton-omous driving. In industrial sorting lines, goods sorting robots often need to work at high speeds to efficiently sort large volumes of items. This poses a challenge to the robot's real-time vision and sorting capabilities, making it both practical and economically viable to implement a real-time and low-cost sorting system in a real-world industrial sorting line. Existing sorting systems have limitations such as high cost, high computing resource consumption, and high power consump-tion. These issues lead to the fact that existing sorting systems are typically used only in large industrial plants. In this paper, we design a high-speed, low-cost, low-resource-consumption FPGA (Field-Programmable Gate Array) based item sorting system that achieves similar perfor-mance to current mainstream sorting systems at a lower cost and consumption than existing sorting systems. The recognition part employs a morphological recognition method, which segments the image using a frame difference algorithm and then extracts the color and shape features of the items. To handle sorting, a six-degree-of-freedom robotic arm is introduced in the sorting segment. The improved cubic B-spline interpolation algorithm is employed to plan the motion trajectory and consequently control the robotic arm to execute the corresponding actions. Through a series of experiments, this system achieves an average recognition delay of 25.26ms, ensures smooth operation of the gripping motion trajectory, minimizes resource consumption, and reduces implementation costs.

In the extra-thick coal seams and multi-layered hard roofs, the longwall hydraulic support yielding, coal face spalling, strong deformations of goaf-side entry, and severe ground pressure dynamic events typically occur at the longwall top coal caving longwall faces. Based on the Key strata theory an overburden caving model is proposed here to predict the multilayered hard strata behaviour. The proposed model together with the measured stress changes in coal seam and underground observations in Tongxin coal mine provides a new idea to analyse stress changes in coal and help to minimise rock bursts in the multi-layered hard rock ground. Using the proposed primary Key and the sub-Key strata units the model predicts the formation and instability of the overlying strata that leads to abrupt dynamic changes to the surrounding rock stress. The data obtained from the vertical stress monitoring in the 38 m wide coal pillar located adjacent to the longwall face indicates that the Key strata layers have a significant influence on ground behaviour. Sudden dynamically driven unloading of strata was caused by the first caving of the sub-Key strata while reloading of the vertical stress occurred when the goaf overhang of the sub-Key strata failed. Based on this findings several measures were recommended to minimise the undesirable dynamic occurrences including pre-split of the hard Key strata by blasting and using the energy consumption yielding reinforcement to support the damage prone gate road areas. Use of the numerical modelling simulations was suggested to improve the key theory accuracy.

Elders have a higher rate of return visits to the emergency department (ED) than other patients. It is critical to understand the risk factors for return visits to the ED by elders. The aim of this study was to determine the factors associated with return visits to the ED by elders. This study retrospectively reviewed the hospital charts of elders who return visits to the ED within 72 hours after discharge. The risk factors identified in the Triage Risk Screening Tool were applied in this study. Of the elders discharged from the ED, 8.64% made a return visit to the ED within 72 hours. The highest revisit rate occurred within 24 hours after discharge. Factors associated with return ED visits within 24 hours by elders were difficulty walking and having discharge care needs. Factors associated with ED return visits within 24–48 hours were cognitive impairment and polypharmacy. Difficulty walking, having discharge care needs and hospitalization within the past 120 days were associated with return visits made within 48–72 hours following discharge. Identifying the reasons for return visits to the ED and providing a continuous review of geriatric assessment and discharge planning could reduce unnecessary revisits.

The Hwangdo tidal flat is an intertidal landform located in Cheonsu Bay, Taean-gun, Chungcheongnam-do, on the west coast of Korea. The topographical characteristics of the semi-enclosed bay on the eastern side of the study area include waterways, sandbars, small islands, and tidal flats. In this study, data were acquired from tide gauges installed on the Hwangdo Bridge, and the height of the ellipsoid was measured using a real-time kinematics global positioning system (RTK-GPS). Digital elevation model (DEM) using Matrice 300 drone data were also acquired after processing. The geochemical sediment characteristics in the study area were analyzed, together with tidal-flat exposure-time characteristics based on environmental factors. Sediment data (n = 107) collected from October 25 to 28, 2022 (Korean local time) were used to classify sediment particles according to Folk and Ward (1957). Sedimentary facies ranged from coarse sand (sand:mud ratio = 9:1) to sandy silt (sZ) followed by muddy sand (mS) and slightly gravelly sandy mud ((g)sM). Total organic carbon (TOC) in the surface sediments were also characterized based on a particle-size analysis. The mean change in tidal height measured at Hwangdo Bridge during the sampling period was ~7.53 m (minimum: –3.86 m, maximum: +3.67 m). Based on the Boryeong's sea level measurement tide data in 2022, the tidal area in the drone images ranged from 6.362 m² (0.006 km²) at DEM +4.0 to 4,841,078 m² (4.841 km²) at DEM –4.0 m, indicating an increase in the tidal-flat area according to the tidal level of up to ~800-fold. The daily average exposure time was 9.0 h (minimum: 1.5 h, maximum: 17.9 h). Based on the results of multivariate analysis using exposure times and a geochemical dataset, four groups were identified: upper, middle, and lower intertidal zones and regions with a relatively high organic-matter concentration. A determination of the main characteristics of the Hwangdo tidal flat according to their spatial distribution showed that, among various environmental factors, changes in the sand or clay sediment composition were determined by community factors. The results of this study demonstrate the four statistically processed groups of marine environmental characteristics in the Hwangdo tidal flats. Changes in sedimentary patterns, rather than in the exposure time, accounted for the differences in the sediment compositions of the upper, middle, and lower stations, a response that is expected to continue.

Dendrobium Sw have multiple photosynthetic pathways but due to the lack of identification, the influence of CAM pathway on the plastid genomic evolution of Dendrobium and the origin of CAM pathway are still poorly understood. In this study, based on the results of δ13C, net photosynthetic rates (Pn) and titratable acid value, we identified Dendrobium species into three photosynthetic pathways. Then the chloroplast whole genome characteristics of 10 Dendrobium species were analyzed with next-generation sequencing technology. The quadripartite-structure plastomes ranged from 151,673 bp to 160,375 bp and included 127 to 132 genes. Five noncoding mutational hotspots (rbcL-accD, atpB-rbcL, rbcL, trnLUAA, accD, Pi > 0.10) were identified. A total of 41–60 SSRs were recognized, the average trinucleotide content was only about 4%, which is probably due to a more conserved SSR. Among multiple photosynthetic pathways, the apparent differences in IR junctions of SSC/IRB junctions (JSBs) were measured within chloroplast genomes, and the chloroplast genome size of constitutive CAM plants is shorter because of their ndh gene loss or pseudogenization, and this phenomenon accounts for a decreasing proportion of constitutive CAM, facultative CAM, and obligate C3 plants, so that the loss of the ndh gene may be speculated to be closely related to the CAM pathway. Phylogenetic analyses showed that there are multiple independent CAM origins in selected Dendrobium species, and the ancestral Dendrobium plastome possessed full ORFs for all ndh genes. The study aims to clarify the chloroplast genomic features of different photosynthetic pathways, enrich the genomic data of CAM plants, and provide genetic information from different perspectives for further systematic study of Dendrobium.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Transient receptor potential melastatin-8 (TRPM8) is a cation channel that is activated by cold and “cooling agents” such as menthol and icilin, which induce a cold sensation. Stimulation of TRPM8 activates an intracellular signaling cascade that ultimately leads to a change in the gene expression pattern of the cells. Here, we investigated the TRPM8-induced signaling pathway that links TRPM8 channel activation to gene transcription. Using a pharmacological approach, we show that inhibition of phosphatidylinositol 4-phosphate 5 kinase alpha (PIP5K), an enzyme essential for the biosynthesis of phosphatidylinositol 4,5-bisphosphate, attenuated TRPM8-induced gene transcription. Analyzing the link between TRPM8 and Gq proteins, we show that pharmacological inhibition of the beta gamma subunits impairs TRPM8 signaling. In addition, genetic studies showed that TRPM8 requires an activated Galpha subunit for signaling. In the nucleus, the TRPM8-induced signaling cascade triggers an activation of the transcription factor AP-1, a complex consisting of a dimer of basic region leucine zipper (bZIP) transcription factors. Here, we identified the bZIP protein c-Jun as an essential component of AP-1 within the TRPM8-induced signling cscade. In summary, with PIP5K, Gq subunits and c-Jun we have identified key molecules in the TRPM8-induced signaling from the plasma membrane to the nucleus.

If we assume that: a. The four fundamental forces of nature are independent waves without rest masses, and their speeds are constant in a vacuum, just like light. b. Light or electromagnetic waves and gravity are comparable in structures. Weak and strong interactions are similar in structures. c. Light and weak interaction have the same speed c_L with spin number +1 or –1. d. Gravity and strong interaction have the same speed c_G without spin. e. The primary particles, namely electrons, electron neutrinos, and dark neutrinos in this paper, are made by the above four waves. We can find and describe some fundamental characteristics of the primary particles (e.g., their sizes, energies, and interactions) and introduce new attractive results from them (e.g., the source of the Pauli exclusion principle, the solution to the Einstein-Podolsky-Rosen paradox, and c_G slightly faster than c_L).

Thermal fluctuations in two-dimensional (2D) isotropy systems at non zero finite temperatures can destroy the long-range (LR) magnetic order due to Mermin-Wanger theory. Interestingly, the magnetic anisotropy related to spin-orbit coupling (SOC) could stabilize magnetic order in 2D systems. Recently, 2D FexGeTe2 (3≤x≤7) with high curie temperature (TC), as a typical 2D van der Waals metallic ferromagnet, has not only made significant progress in synthetic methods and controlling ferromagnetism (FM), but also actively explored many device applications. In this Review, we introduce six experimental methods, ten ferromagnetic modulation strategies, and three spintronic devices of 2D FexGeTe2 materials. Overall, we have outlined the challenges and potential research directions in this field.

Electricity generation from renewable energy sources is emerging as a result of global carbon emission reduction policies. However, most renewable energy sources are non-dispatchable and cannot be adjusted to meet the fluctuating electricity demands of society. A flexible operation process has been proposed as an effective solution to compensate for the unstable nature of renewable energy sources. Thermal load fluctuations during flexible operation may cause creep-fatigue damage to the high-temperature components of thermal power plants, as they are designed with a focus on creep damage under a constant power level. This study investigated the residual life of high-temperature components, such as a superheater tube and a reheater header, to failure under flexible operation conditions using finite element analysis and empirical models. First, we determine an analytical solution for the straightened superheater tube under thermal conditions and compare it with the numerical solution to verify the numerical models. Through the verified finite element model, the creep-fatigue life of the reheater header is estimated by considering flexible operation factors and employing the Coffin-Manson and Larson-Miller models. Although fatigue damage increases with decreasing minimum load and ramp rate, we confirmed that creep damage significantly affects the residual life during flexible operation. In addition, a surrogate model was proposed to evaluate the residual life of the reheater as a function of the flexible operation factors using the machine learning methodology, based on the results of finite element methods. It can be used to predict its residual life without performing complex thermal-structure analysis and relying on empirical models for fatigue and creep life. We expect our findings to contribute to the efficient operation of thermal power plants by optimizing the flexible operation factors.

In South Korea, in line with the increasing need for a reliable water supply following the continuous increase in water demand, the Smart Water Grid Research Group (SWGRG) was officially launched in 2012. With the vision of providing water welfare at a national level, SWGRG incorporated information and communications technology in its water resource management, aiming at the development of core technologies for a Smart Water Grid consisting of intelligent microgrids and a demonstration and tests of the developed technologies through a field operation in a living lab. The living lab was built in Block 112 of YeongJong Island, Incheon, South Korea (area of 17.4 km2, population of 8,000), where Incheon International Airport, a hub of Northeast Asia, is located. In this location, water is supplied through a single submarine pipeline, making the place optimal for responses to water crises and the construction of a water supply system during emergencies. From 2017 to 2019, ultrasonic wave type smart water meters and IEEE 802.15.4g advanced metering infrastructure (AMI) networks were installed at 527 sites of 958 consumer areas in the living lab, and core element technologies (intelligent water source management and distribution system, smart water distribution network planning/control/operation strategy establishment, AMI network and device development, integrated management of bi-directional smart water information), and operation solutions (smart water statistics information, real-time demand-supply analysis, decision support system, real-time hydraulic pipeline network analysis, smart DB management, and water information mobile application) were developed through a field operation and testing.

Alzheimer’s disease (AD) is a chronic neurodegenerative disease, and typical pathologic findings include abnormally hyperphosphorylated tau aggregation and neurofibrillary tangles. Insulin resistance and hyperglycemia have been assessed as risk factors for AD development. As the maintenance of optimal blood glucose levels is an important indicator of diabetes mellitus (DM) treatment, diet control is essential. AMPK is a crucial sensor of cellular bioenergetics for controlling anabolic and catabolic metabolism. Diet restriction to achieve euglycemia can increase AMPK activity in the liver and heart. Since AMPK is a direct regulator of tau phosphorylation, we hypothesized that strict diet control to achieve euglycemia affects tau protein phosphorylation through increased AMPK activity in the hippocampus of DM rats. To confirm this hypothesis, we generated insulin-deficient DM rats by subtotal pancreatectomy. Animals were categorized into the restriction (R) group, control (C) group and ad libitum (AL) group according to the diet. We found that tau phosphorylation was significantly increased in the R group compared with the C or AL group. AMPK activity in the R group significantly increased compared to that of the C group or AL group, as expected. Furthermore, the R group showed more critical tau pathology in the hippocampus than the other groups. These results suggest that diet control to achieve euglycemia in insulin-deficient DM conditions is harmful because of the increased possibility of AD development through increased tau phosphorylation by AMPK activation in the hippocampus. We propose that not only hyperglycemia but also euglycemia, which is beneficial in DM patients, must be considered a potential risk factor for AD development, especially when euglycemia is achieved by diet control during insulin deficiency.

There is limited evidence for the association between malnutrition and hospital mortality as well as Intensive Care Unit length-of-stay (ICU-LOS) in critically ill patients. We aimed to examine the aforementioned associations by conducting a prospective cohort study in an ICU of a Singapore tertiary hospital. Between August 2015 and October 2016, all adult patients with ≥24 h of ICU-LOS were included. The 7-point Subjective Global Assessment (7-point SGA) was used to determine patients’ nutritional status within 48 hours of ICU admission. Multivariate analyses were conducted in two ways: 1) presence versus absence of malnutrition, and 2) dose-dependent association for each 1-point decrease in the 7-point SGA. There were 439 patients of which 28.0% were malnourished, and 29.6% died before hospital discharge. Malnutrition was associated with an increased risk of hospital mortality [adjusted-RR 1.39 (95%CI: 1.10–1.76)], and this risk increased with a greater degree of malnutrition [adjusted-RR 1.09 (95%CI: 1.01–1.18) for each 1-point decrease in the 7-point SGA]. No significant association was found between malnutrition and ICU-LOS. Conclusion: There was a clear association between malnutrition and higher hospital mortality in critically ill patients. The association between malnutrition and ICU-LOS could not be replicated and hence requires further evaluation.

We performed Bayesian network meta-analysis (NMA) to suggest frontline treatments for patients with high PD-L1 expression (at least 50%). A total of 5,237 patients from 22 studies were included in this NMA. In terms of progression-free survival, immune checkpoint inhibitors (ICIs) plus bevacizumab plus chemotherapy had the highest surface under the cumulative ranking curve (SUCRA) value (98.1%), followed by ICI plus chemotherapy (82.9%). In terms of overall survival (OS), dual immunotherapy plus chemotherapy had the highest SUCRA value (79.1%), followed by ICI plus bevacizumab plus chemotherapy (73.4%). However, there was no significant difference of survival outcomes among treatment regimens combined with immunotherapy. Moreover, ICI plus chemotherapy failed to reveal a significant OS superiority to ICI monotherapy (hazard ratio = 0.978, 95% credible internal: 0.771-1.259). In conclusion, this NMA indicates that ICI plus chemotherapy with/without bevacizumab might to be the best options in terms of OS for NSCLC with high PD-L1 expression. Considering there was no significant difference of survival outcomes among treatment regimens incorporating immunotherapy and ICI plus chemotherapy failed to show significant survival benefits over ICI monotherapy, however, ICI monotherapy may be reasonable as first-line treatment for advanced NSCLC with high PD-L1 expression and no targetable aberrations.

Due to the shortage of agricultural labor forces and rapid aging of farmers, the utilization of tractors is becoming popular and essential in Korea. Tractors can be classified into two types, a walking tractor called as a power tiller and a riding tractor. In this study, agricultural tractors including walking and riding types were categorized into 4 levels by rated output power. And diesel emission inventory of tractors was established and analyzed using 2011 and 2019 survey data in Korea. Emission inventory including CO, NOx, SOx, TSP(PM10), PM2.5, VOCs and NH3 were established using Tier 3 methodology. The total amount of emission using agricultural tractors was decreased about 13% from 2011 to 2019. The number of walking tractors were decreased by about 19% in 8 years, on the other hand that of riding tractors were increased by about 12%. However, the emission reduction is about 48% for walking tractors and the emission increment is about 5% for riding tractors. Thus, the total emission from agricultural tractors was decreased by about 16% in those periods. It is due to the decrease of 21% and 15% in the hours of use of walking and riding tractors, respectively, in 2019. Walking tractors mainly emit air pollutants from spraying and transporting. Riding tractors mainly 61% of total air pollutants emits from soil preparation and transporting operations. Geographic information system (GIS) was used to spatially assign air pollutants variables into 17 provinces and metropolitan cities in Korea. High emission generating regions and changes of emissions during 8 years were clearly seen in GIS analysis. High air pollutant emitting regions are mainly located in the western and southern regions of Korea, which have plenty of arable areas compared to other regions in Korea.

In Korea, rice is a major staple grain and is mainly cultivated using various agricultural machinery. Air pollutants emitted from agricultural machinery have their origins mainly from the exhaustion of internal combustion engines. In this study, emission characteristics of five main air pollutants by European Environment Agency's Tier 1 method for rice cultivation was analyzed. Diesel is a main fuel for agricultural machinery and gasoline is generally used only for rice transplanters as a fuel in Korea. Tractors consume 46% of total fuel consumption and 56% of diesel fuel consumption. Gasoline used for rice transplanters accounts for 17% of total fuel consumption each year. Tractors and rice transplanters are emitting 82% of all total pollutants. From 2011 to 2019, the total amount of air pollutant emissions was decrease by 15%. That accounted for the reduction of rice cultivation fields in those periods. Rice transplanting operation was in charge of 42% of total emissions. Then, harrowing, harvesting, tilling, leveling, and pest control operations generated 10%, 10%, 8%, 8% and 7% of total emissions, respectively. The contribution of each air pollutant held 54% of CO, 39% of NOx, 5% of NMVOC, and 2% of TSP from the total emission inventory. The three major regions emitting air pollutants from mechanized agricultural practices were Jeollanam-do, Chungcheongnam-do, and Jeollabuk-do, which consume 55% of total fuel usage in rice farming. The total amount of air pollutant emissions from rice cultivation practices in 2019 was calculated as 8,448 Mg in Korea.

Shear connectors are used in steel beam–concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. We performed push-out tests of stubby Y-type perfobond rib shear connectors for composite frames. These shear connectors have relatively small ribs than conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

The so-called “Chinese pyramids” are huge burial mounds covering the tombs of the Emperors of the Western Han dynasty. If we include also the mounds of the members of the royal families, these monuments sum up to more than 40, scattered throughout the western and the southern outskirts of modern Xi'an. They are mostly unexcavated and poorly known although, taken together, they form a fascinating sacred landscape, which was conceived as a perennial witness of one of the most magnificent Chinese dynasties. This sacred landscape is today encroached by the frenetic urban development of the Xi’an urban area. We discuss and elaborate here some of the results of a recent, new satellite-imagery survey of these monuments, highlighting the aspects which may contribute to solutions for a sustainable and compatible development within this important ancient landscape.

Wool quality and yield are important economic traits of livestock. In this study, the skin tissues of the upper scapula of Super Merino sheep (SM) and Small-Tailed Han sheep (STH) during the growing period were studied. Differentially expressed (DE) long non-coding RNAs (lncRNAs) and messenger RNAs (mRNA) were identified via histopathological observation and high-throughput RNA sequencing. Gene ontology (GO) and the Kyoto Encyclopedia of Genes and Genomes (KEGG) were used to analyze differentially expressed genes. Reverse transcription quantitative Polymerase Chain Reaction (RT-qPCR) was used to verify nine selected DE lncRNAs and five DE mRNAs. Significant differences were found in the expression levels of LOC114113396 (KRTAP15-1), CRABP1, KRT10, KRTAP1-3, KRTAP4.3, KRT2, FGF1, IGF-1, and KIT in SM and STH skin tissues. These results indicate that these mRNAs may play an important role in the growth and development of hair follicles and the regulation of hair fiber traits. Differentially expressed lncRNA target genes and mRNAs were mainly enriched in biological processes and pathways related to skin development and fiber traits, which is consistent with previous studies. LncRNA MSTRG.9225.1, MSTRG.124320.1, MSTRG.96951.1, MSTRG.91685.1, MSTRG.122229.1, MSTRG.89255.1, MSTRG.98769.1, and MSTRG.84658.1 may indirectly participate in the growth and development of sheep hair follicles and the regulation of hair fiber diameter by regulating the expression of their respective target genes. These candidate lncRNAs and mRNAs may provide a basis for the study of sheep hair follicle growth and development and hair fiber traits.

Levels of synthetic musk fragrances (SMFs) and various personal care products (PCPs) were measured in the Han River and its tributaries in Seoul, Korea. The most abundant SMF in all river and PCP samples was 4,6,6,7,8,8-hexamethyl-1,3,4,7-tetrahydrocyclopenta[g]isochromene (HHCB), followed by 1-(3,5,5,6,8,8-hexamethyl-6,7-dihydronaphthalen-2-yl)ethanone (AHTN), musk ketone (MK), and 1,1,2,3,3-pentamethyl-2,5,6,7-tetrahydroinden-4-one (DPMI). There was a significant correlation between the SMF concentration in the PCPs and the Han River samples. Moving from upstream to downstream in the Han River, the median SMF concentration was 6.756, 2.945, 0.304, and 0.141 μg/L in the sewage treatment plant (STP) influent, effluent, tributaries, and mainstream, respectively, implying that effective SMF removal was achieved during the sewage treatment process, followed by dilution in the receiving water. Four STPs using advanced biological treatment processes had removal efficiencies of 55.8%, 50.6%, 43.3% for HHCB, AHTN, and MK, respectively. The highest SMF concentrations in the tributaries were observed at locations close to the STPs. Our study confirmed that the main source of SMFs in the receiving water were sewage effluent containing untreated SMFs, which are largely originated from household PCPs, especially hair care products (e.g., shampoo) and perfumes.

In this study, we examine microscale waterflooding in a randomly close-packed porous medium. Three different porosities are prepared in a microfluidic platform and saturated with silicone oil. Optical video fluorescence microscopy is used to track the water front as it flows through the porous packed bed. The degree of water saturation is compared to water containing two different types of chemical modifiers, sodium dodecyl sulfate (SDS) and polyvinylpyrrolidone (PVP), with water in the absence of a surfactant used as a control. Image analysis of our video data yield saturation curves and calculate fractal dimension, which we use to identify how morphology changes the way an invading water phase moves through the porous media. An inverse analysis based on the implicit pressure explicit saturation (IMPES) simulation technique uses mobility ratio as an adjustable parameter to fit our experimental saturation curves. The results from our inverse analysis combined with our image analysis show that this platform can be used to evaluate the effectiveness of surfactants or polymers as additives for enhancing the transport of water through an oil-saturated porous medium.

The aim of this paper is to compare the taxonomic composition and species diversity of the macrozoobenthos in Maritsa River (Bulgaria) and Han River (South Korea). Samples were collected at 15 selected sites in each river, including some of their main tributaries in 2020 and 2021. The number of the taxa recorded in Maritsa River was more than twice as great as in Han River: 192 taxa belonging to 19 systematic groups compared to 88 taxa belonging to 18 groups respectively. The order Ephemeroptera had the highest species richness: 31 taxa in the Bulgarian rivers and 26 taxa in the South Korean ones. The macrozoobenthic communities responded and adapted to the various conditions and impacts in the water environment with changes in the species composition and structure. The analysis of the similarity in the taxonomic composition showed low resemblance between all study sites but displayed distinct separations between the rivers and the two years. In general, the species structure of the macrozoobenthic communities in Maritsa River and its studied tributaries was better than in Han River. In both years, high species diversity was recorded at the reference sites in the rivers, characterized by conditions closely resembling natural environments. The species richness and the evenness of macrozoobenthos were very low at sites downstream subjected to considerable anthropogenic pressure. Some of the communities in Han River were almost destroyed completely.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

The iridoids of H. diffusa play an important role in the anti-inflammatory process, but the specific iridoid with anti-inflammatory effect and its mechanism is lack of study. An iridoid compound named scandoside (SCA) was isolated from H. diffusa and its anti-inflammatory effect was investigated in lipopolysaccharide (LPS)-induced RAW 264.7 cells. Its anti-inflammatory mechanism was confirmed by in intro experiment and molecular docking analysis. As results, SCA significantly decreased the productions of nitric oxide (NO), prostaglandin E₂ (PGE₂), tumor necrosis factor-α (TNF-α) and interleukin-6 (IL-6) and inhibited the levels of inducible nitric oxide synthase (iNOS), cyclooxygenase-2 (COX-2), TNF-α and IL-6 mRNA expression in LPS-induced RAW 264.7 cells. SCA treatment suppressed the phosphorylation of inhibitor of nuclear transcription factor kappa-B alpaha (IκB-α), p38, extracellular signal-regulated kinase (ERK) and c-Jun N-terminal kinase (JNK). The docking data suggested that SCA had great binding abilities to COX-2, iNOS and IκB. Taken together, the results indicated that the anti-inflammatory effect of SCA is due to inhibition of pro-inflammatory cytokines and mediators via suppressing the nuclear transcription factor kappa-B (NF-κB) and mitogen-activated protein kinase (MAPK) signaling pathways, which provided useful information for its application and development.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

Due to rising global warming and climate change, biodiversity protection has become a critical ecological concern. The rich biodiversity zones are under threat and are deteriorating, necessitating national, regional, and provincial efforts to safeguard these natural areas. The effective conservation of National Parks and Nature-protected Areas helps to improve biodiversity conservation, forest, and urban air quality. The continuous encroachment and abuse of these protected areas have degraded the ecosystem over time. While exploring the geophysical ecology and biodiversity conservation of these areas in West Africa, Kainji National Park was selected for this study because of its notable location, naturalness, rich habitat diversity, topographic uniqueness, and landmass. The conservation of national parks and nature-protected areas is a cornerstone of biodiversity conservation globally. This study is aimed at the target of United Nations Sustainable Development Goal 13, 2030- Climate Action, targeted at taking urgent action towards combating climate change and its impacts. The study captures both flora and fauna that are dominant in the study area. The 15 identified tree species were selected from over 30 species with 563,500,000 (an average of 3,700,000 in each sample frame) trees for every tree species/type with a total of 63% tree green canopy cover. The study areas divided into three zones were randomly sampled within a stratum of 25x25km frames divided into 150 sample frames for proper analyses using the i-Tree Eco v6.0.23. The following microclimatic data were captured and analyzed; photosynthetically active radiation, rain/precipitation, temperature, transpiration, evaporation, water intercepted by trees, avoided a runoff by trees, potential evaporation by trees, isoprene and monoterpene by trees. This study also further discusses the tree benefits of a green, low carbon, and sustainable environment within the context of biodiversity conservation considering carbon storage, carbon sequestration, hydrology effects, pollution removal, oxygen production, and volatile organic compounds (VOCs). There is a quick need for remotely-sensed information about the protected areas at regular intervals and government policies must be strict against illegal poaching, logging activities and other hazardous human impacts.

Establishing an effective evaluation model to analyze the actual environmental level of the multi-indicator systems is an urgent challenge. However, due to the complexity of the environmental system, the factors that determine the practical system are usually interrelated. To solve this problem, many methods have been proposed and verified. However, the disadvantage of unreasonable weight determination and only single-indicator assessment limits the practical application of these analysis methods. Here, we established an optimized entropy weight model and integrate it with the fuzzy comprehensive evaluation (FCE) method to quantify the complex environmental system. By introducing the linear programming method into the entropy weight solution, we can obtain high accuracy weight values and strong resistance to extreme data. Theoretical and simulation results demonstrate that our method can enhance the precision of weight calculation and evaluation results for multi-factor systems. Our work develops an effective method to quantify the complex environment system comprehensively and is significant to real applications of evaluation method.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

As the lifespan of porous asphalt pavement extends, it invariably experiences performance degradation and an increase in tire/pavement noise compared with the original surface when it is newly built. To understand the medium-term performance of porous asphalt pavement during service and reveal the influence of different pavement performance indicators on tire/pavement noise generation, a seven-year continuous observation and data analysis study was conducted. Porous asphalt with different designed material parameters was taken into account, including thin-layer porous asphalt overlay with a maximum nominal aggregate size of 10mm (PUC-10), porous asphalt with a maximum nominal aggregate size of 13mm (PAC-13), and a two-layer porous asphalt incorporating both PUC-10 and PAC-13 (PUC-10+PAC-13). Using automated pavement technology testing equipment, key performance indexes, including damage rate (DR), rut depth (RD), international roughness index (IRI), and sideway force coefficient (SFC), were measured and calculated. The on-board sound intensity (OBSI) method was used to test noise levels in three types of porous asphalt pavement structures and on a dense graded easy compact asphalt concrete (ECA) for comparison. The progressions of the medium-term performances were analyzed according to the measured results. The correlations between tire/pavement noise levels and testing speed, testing lane, pavement structure, and road condition indicators were investigated by regression. The research results revealed that the DR and SFC of the three types of porous asphalt pavement displayed more significant attenuation in the service period, while the IRI and RD showed small changes. Among them, the SFC demonstrated significant attenuation over the first 4 years, decreasing between 13.8% and 17.0%. From the 3-7 years of operation, the transverse crack disease in porous asphalt pavement progressed rapidly. The three porous asphalt pavement structures tested exhibited commendable noise reduction capabilities. Compared to ECA, the OBSI noise levels of these structures were lower by 2.09 dB, 1.53 dB, and 2.88 dB, respectively. Compared to other pavement condition indicators, RD had a more significant impact on the OBSI value of the PUC-10 porous asphalt pavement. For the PUC-10+PAC-13 porous asphalt pavement, there was a significant linear relationship between the OBSI value and SFC, mainly due to polishing of the coarse aggregate surface. It leads to a decrease of the micro-texture, which lies in increasing tire/pavement noise at high-frequency ranges and decreasing SFC. This study will have guiding significance for the research of the attenuated law and durability improvement of porous asphalt tire/pavement noise.

It is crucial to forecast the water demand accurately for supplying water efficiently and stably in a water supply system. In particular, accurately forecasting short-term water demand helps in saving energy and reducing operating costs. With the introduction of the Smart Water Grid (SWG) in a water supply system, the amount of water consumption is obtained in real time through an advanced metering infrastructure (AMI) sensor, which can be used for forecasting the short-term water demand. The models widely used for water demand forecasting include the autoregressive integrated moving average, radial basis function-artificial neural network, quantitative multi-model predictor plus, and long short-term memory. However, there is a lack of research on assessing the performance of models and forecasting the short-term water demand by applying the data on the amount of water consumption by purpose and the pipe diameter of an end-use level of the SWG demonstration plant in each demand forecasting model. Therefore, in this study, the short-term water demand was forecasted for each model using the data collected from the AMI, and the performance of each model was assessed. The Smart Water Grid Research Group installed ultrasonic-wave-type AMI sensors in the block 112 located in YeongJong Island, Incheon, and the actual data used for operating the SWG demonstration plant were adopted. The performance of the model was assessed by using the residual, root mean square error (RMSE), normalized root mean square error (NRMSE), Nash–Sutcliffe efficiency (NSE), and Pearson correlation coefficient (PCC) as indices. The water demand forecast was slightly underestimated in models that employed the assessment results based on the RMSE and NRMSE. Furthermore, the forecasting accuracy was low for the NSE due to a large number of negative values; the correlation between the observed and forecasted values of the PCC was not high, and it was difficult to forecast the peak amount of water consumption. Therefore, as the short-term water demand forecasting models using only time and the amount of water consumption have limitations in reflecting the characteristics of consumers, a water supply system can be managed more precisely if other factors (weather, customer behavior, etc.) influencing the water demand are applied.

Electrospun nanofiber-supported thin film composite membranes are among the most promising membranes for seawater desalination via forward osmosis. In this study, a high-performance electrospun polyvinylidenefluoride (PVDF) nanofiber-supported TFC membrane was successfully fabricated after molecular layer-by-layer polyelectrolyte deposition. Negatively-charged electrospun polyacrylic acid (PAA) nanofibers were deposited on electrospun PVDF nanofibers to form a support layer consisted of PVDF and PAA nanofibers. This resulted to a more hydrophilic support compared to the plain PVDF nanofiber support. The PVDF-PAA nanofiber support then underwent a layer-by-layer deposition of polyethylenimine (PEI) and PAA to form a polyelectrolyte layer on the nanofiber surface prior to interfacial polymerization, which forms the selective polyamide layer of TFC membranes. The resultant PVDF-LbL TFC membrane exhibited enhanced hydrophilicity and porosity, without sacrificing mechanical strength. As a result, it showed high pure water permeability and low structural parameter values of 4.12 Lm⁻²h⁻¹bar⁻¹ and 221 µm, respectively, significantly better compared to commercial FO membrane. Layer-by-layer deposition of polyelectrolyte is therefore a useful and practical modification method for fabrication of high performance nanofiber-supported TFC membrane.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

Cadmium(Cd) is a highly toxic and cumulative environmental pollutant. Siderophores are heavy metal chelators with high tolerance to heavy metals such as Cd. Furthermore, ryegrass (Lolium perenne L.) has potential remediation capacity for soils contaminated by heavy metals. Consequently, using ryegrass alongside beneficial soil microorganisms that produce siderophores may be an effective means to remediate soils contaminated with Cd. In this study, Bacillus strains WL1210 and CD303 that were previously isolated from the rhizospheres of Nitraria tangutorum in Wulan and Peganum harmala L in Dachaidan, respectively, both arid sandy environments, were evaluated for heavy metal pollution mitigation. The results indicate that both strains of Bacillus exhibit favorable biological characteristics and stress resistance, and they are both producers of siderophores, which promote the growth of ryegrass under Cd stress.

(1) Background: Proximal humerus fractures can be a debilitating condition if not properly treated. These fracture patterns are varied and differ in every patient. Functional outcomes may be determined by the integrity of the shoulder girdle involving the rotator cuff insertion. The post-operative resorption or malreduction of the greater tuberosity is an important factor contributing to the poor functional outcome of a patient. (2) Methods: A single-center retrospective comparative study was performed to evaluate the functional outcomes of patients undergoing operative fixation for this injury. A total of 387 consecutive cases treated operatively from 2019-2021 were included for analysis. (3) Results: 94 cases fulfilled our criteria for analysis. A matched-group comparison of 19 patients each was performed to compare demographics, post-operative fracture characteristics and functional outcomes. (4) Conclusions: The resorption or malreduction of the greater tuberosity contributes greatly to the prognostic outcome in patients treated with ORIF surgery. In our demographic study, obesity is another contributing factor affecting the parameters of post-operative reduction in proximal humerus fractures. Appropriate surgical planning and post-operative multidisciplinary care must be taken into consideration to attain a satisfactory prognostic outcome.

Falls, highly common in the constantly increasing global aging population, can have a variety of negative effects on their health, well-being, and quality of life, including restricting their capabilities to conduct Activities of Daily Living (ADLs), which are crucial for one’s sustenance. Timely assistance during falls is highly necessary, which involves tracking the indoor location of the elderly during their diverse navigational patterns associated with ADLs to detect the precise location of a fall. With the decreasing caregiver population on a global scale, it is important that the future of intelligent living environments can detect falls during ADL.s while being able to track the indoor location of the elderly in the real world. Prior works in these fields have several limitations, such as – the lack of functionalities to detect both falls and indoor locations, high cost of implementation, complicated design, the requirement of multiple hardware components for deployment, and the necessity to develop new hardware for implementation, which make the wide-scale deployment of such technologies challenging. To address these challenges, this work proposes a cost-effective and simplistic design paradigm for an Ambient Assisted Living system that can capture multimodal components of user behaviors during ADLs that are necessary for performing fall detection and indoor localization in a simultaneous manner in the real world. Proof of concept results from real-world experiments are presented to uphold the effective working of the system. The findings from two comparison studies with prior works in this field are also presented to uphold the novelty of this work. The first comparison study shows how the proposed system outperforms prior works in the areas of indoor localization and fall detection in terms of the effectiveness of its software design and hardware design. The second comparison study shows that the cost for the development of this system is the least as compared to prior works in these fields, which involved real-world development of the underlining systems, thereby upholding its cost-effective nature.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

Traveling salesman problems (TSPs) are well-known combinatorial optimization problems, and most existing algorithms are challenging for solving TSPs when its scale is large. To improve the efficiency of solving large-scale TSPs, this work presents a novel adaptive layered clustering framework with improved genetic algorithm (ALC\_IGA). The primary idea behind ALC\_IGA is to break down a large-scale problem into a series of small-scale problems. First, the $k$-means and improved genetic algorithm are used to segment the large-scale TSPs layer by layer and generate the initial solution. Then, the developed two phases simplified $2$-opt algorithm is applied to further improve the quality of the initial solution. The analysis reveals that the computational complexity of the ALC\_IGA is between $O(n\log n)$ and $O(n^2)$. The results of numerical experiments on various TSP instances indicate that, in most situations, the ALC\_IGA surpasses the state-of-the-art algorithms in convergence speed, stability, and solution quality. Specifically, the ALC\_IGA can solve instances with $2 \times 10^5$ nodes within 0.15h, $1.4 \times 10^6$ nodes within 1h, and $2 \times 10^6$ nodes in three dimensions within 1.5h.

Spices rich in polyphenols are metabolized to a convergent group of phenolic acids. We conducted a dose-exposure nutrikinetic study to investigate associations between mixed spices intake and plasma concentrations of selected, unconjugated phenolic acids. In a randomized crossover study, 20 Chinese males consumed a curry meal containing 0 g, 6 g, and 12 g of mixed spices. Postprandial blood was drawn up to 7 h at regular intervals and plasma phenolic acids were quantified via LC-MS/MS. Cinnamic acid (CNA, p < 0.0001) and phenylacetic acid (PAA, p < 0.0005) concentrations were significantly increased with mixed spices consumption, although none of the other measured phenolic acids differ significantly between treatments. CNA displayed a high dose-exposure association (R² > 0.8, p < 0.0001). The adjusted mean AUC_{0-7 h} for CNA during the 3 increasing doses were 8.4 ± 3.4, 376.1 ± 104.7 and 875.7 ± 291.9 nM·h respectively. Plasma CNA concentration may be used as a biomarker of spice intake.

Remote sensing (RS) as a landscape planning and management tool for socio-cultural diversity and inclusiveness in protected(reserved) areas through monitoring of the land-use changes, settlement/living patterns, predominant trades/socio-economic activities in the urban-rural locations, and the demography in Sub-Saharan Africa (SSA). The eighteen federal governments recognized nature reserves in Nigeria being the giant of Africa because of their green landscapes, rich biodiversity, and human resources. This study aimed to explore the application of remote sensing to assess the extent of land degradation and encroachment in the 18 recognized national parks in Nigeria. A review of the protection of national parks using remote sensing and monitoring the trend of national park invasions which could either be natural or man-made. The study is in line with the United Nations SDG Goal 15: Life on Land- “Protect, restore and promote sustainable use of terrestrial ecosystems, sustainably manage forests, combat desertification, and halt and reverse land degradation and halt biodiversity loss”. Located in the West Africa subregion lying on Latitude: 9° 04' 39.90" N (9.077899) and Longitude: 8° 40' 38.84" E (8.677599), with an estimated population of over 220,000,000 people. This study through an intensive review of various literature adopted a mixed approach for the analysis and assessment of the geospatial data, the updated aerial photographs obtained through the Landsat imageries (Google Earth Pro, 2023), and the use of GIS for Geospatial analysis which enables the collection and analysis of spatial and geographic data gathering land use/land covers (LULC) maps, soil type, and elevation maps. While exploring the geophysical ecology and biodiversity conservation of some selected national parks in Nigeria, while also providing cost-effective alternatives for biodiversity monitoring and conservation strategy development. A review of national implementation strategies on biodiversity conservation with the deployment of remote sensing technologies, it is now feasible to obtain large details of the surface of the planet without conducting arduous field activities with the assistance of the availability of multi-date, multi-resolution, multi-sensor aerial information to help prevent for encroachment, loss, and degradation of the natural landscapes.

Liver cirrhosis leads to hepatic dysfunction and life-threatening conditions. Though clinical efficacy of autologous bone marrow-drived mesenchymal stem cells (BM-MSC) transplantation in alcoholic cirrhosis (AC) was demonstrated, the relevant mechanism has not been elucidated. We aimed to identify predictive factors and gene/pathways for responders after autologous BM-MSC transplantation. Fifty-five patients with biopsy-proven AC underwent autologous BM-MSC transplantation. The characteristics of responders who showed improvement in fibrosis score (≥ 1) after transplantation were compared with those of non-responders. BM-MSCs were analyzed with cDNA microarrays to identify genes and pathways that were differentially expressed in responder after transplantation. Thirty-three patients (66%) were responders. In the multivariate analysis, initial high Laennec score (p=0.007, odds ratio 3.73) and performance of BM-MSC transplantation (p=0.033, odds ratio 5.75) were predictive factors for responder. Three genes (olfactory receptor 2L8, microRNA4520-2, and chloride intracellular channel protein 3) were upregulated in responders and 11 metabolic pathways (inositol phosphate, ATP-binding cassette transporters, protein kinase signaling, extracellular matrix-receptor interaction, endocytosis, phagosome, hematopoietic cell lineage, adipocytokine, peroxisome proliferator-activated receptor, fat digestion/absorption, and insulin resistance) were upregulated in non-responders (p<0.05). BM-MSC transplantation is warranted treatment for AC patients with high Laennec score. Cell-based therapy utilizing response-relating genes or pathway can be treatment candidate.

The COVID-19 pandemic caused by the novel coronavirus emerged in Wuhan City, Hubei province of China at the end of 2019, has radically transformed the lives of people around the world. Due to its fast spreading, it is currently considered as a worldwide health, social and economic concern. The lack of knowledge on this area has encouraged academic sphere for extensive research, which is reflected in exponentially growing scientific literature in this area. However, current state of COVID-19 research reveals only early development of knowledge, while a comprehensive and in-depth overview remains neglected. Accordingly, the main aim of this paper is to fill the aforementioned gap in the literature and provide an extensive bibliometric analysis of COVID-19 research across science and social science research landscape, using innovative and sophisticated bibliometric approaches (e.g. Venn diagram, Biblioshiny descriptive statistics, VOSviewer co-occurrence network analysis, Jaccard distance cluster analysis, text mining based on logistic regression). The bibliometric analysis is based on the Scopus database including all relevant and latest information on COVID-19 related publications (n=16,866) in the first half of 2020. The empirical results indicate that there is still a lack of publications of COVID-19 and its implications in less-explored (non-health) sciences, especially in social sciences. Accordingly, the findings emphasize an importance of a comprehensive and in-depth approach considering different scientific disciplines in COVID-19 research. The understanding of the evolution of emerging scientific knowledge on COVID-19 is beneficial not only for scientific community but also for evidence-based policymaking in order to prevent and address the COVID-19 pandemic.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

With the rapid evolution of SARS-CoV-2, the emergence of new strains is an intriguing question. This paper presents an evolutionary theory to analyze the mutations of the virus and identify the conditions that lead to the generation of new strains. We represent the virus variants using a 4-letter sequence based on amino acid mutations on the spike protein and employ an n-distance algorithm to derive a variant phylogenetic tree. We show that the theoretically-derived tree aligns with experimental data on virus evolution. Additionally, we propose an A-X model, utilizing the set of existing mutation sites (A) and a set of randomly generated sites (X), to calculate the emergence of new strains. Our findings demonstrate that a sufficient number of random iterations can predict the generation of new macro-lineages when the number of sites in X is large enough. These results provide a crucial theoretical basis for understanding the evolution of SARS-CoV-2.

Gas flaring is commonly used by industrial plants for processing oil and natural gases in the atmosphere, and hence is an important anthropogenic source for various pollutants including CO₂, CO, and aerosols. This study evaluates the feasibility of using satellite data to characterize gas flaring form space by focusing on the Khanty Mansiysk Autonomous Okrug in Russia, a region that is well known for its dominatingly gas flaring activities. Multiple satellite-based thermal anomaly data products at night are inter-compared and analyzed, including MODIS (Moderate Resolution Imaging Spectroradiometer) Terra level-2 Thermal Anomalies product (MOD14), MODIS Aqua level-2 Thermal Anomalies product (MYD14), VIIRS (Visible Infrared Imaging Radiometer Suite) Active Fires Applications Related Product (VAFP), and VIIRS level-2 data based Nightfire product (VNF). The analysis compares and contrasts the efficacy of these sensor products in detecting small, hot sources like flares on the ground in extremely cold environments such as Russia. We found that the VNF algorithm recently launched by NOAA has the unprecedented accuracy and efficiency in characterizing gas flares in the region owing primarily to the use of Shortwave Infrared (SWIR) bands. Reconciliation of VNF’s differences and similarities with other nighttime fire products is also conducted, indicating that MOD14/MYD14 and VAFP data are only effective in detecting those gas flaring pixels that are among the hottest in the region. Validation of VNF product of gas flaring location with Google Earth images are made. It is shown that that VNF’s estimates of gas flaring area (the area of gas flaming) agree well the counterparts from Google images with a linear correlation of 0.91, highlighting its potential use for routinely monitoring emissions of gas flaring from space.

Pleione is a genus of Orchidaceae and is one of the major sources of Pseudobulbus Cremastrae seu Pleiones (PCsP). It contains many constituents, such as phenanthrene, bibenzyl, glycoside, flavonoid and so on, which have plenty of bioactivities, including anti-tumor, anti-oxidation, anti-inflammatory, lowering glycemic levels and other pharma cological activities. In order to further utilize the edible and medicinal functions of Pleione, and clarify its medicinal active ingredients, this review systematically summarizes the constituents and pharmacological effects of Pleione, which will provide a theoretical foundation for the clinical application and new drug development．

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Medical Self-service Terminals (MST) offer potential for process optimization and enhanced patient convenience in hospitals, including the elderly. However, the behavioral inclination (BI) of elderly Chinese individuals towards MST adoption remains suboptimal. This study aims to elucidate BI determinants for MST among the aging demographic, focusing on User Interface (UI) attributes within the extended Unified Technology Acceptance and Use Theory (UTAUT) Model. The empirical inquiry examines seven factors, comprising three key UI attributes and four fundamental UTAUT factors. Results reveal significant positive associations of Performance Expectancy (β=0.40, p&lt;0.001), Effort Expectancy (β=0.50, p&lt;0.001), and Social Influence (β=0.25, p&lt;0.05) with BI. Notably, User Interface Design positively correlates with Performance Expectancy (β=0.89, p&lt;0.001) and Effort Expectancy (β=0.81, p&lt;0.001). These findings emphasize the interplay between objective UI attributes and subjective UTAUT determinants. This research enhances understanding of UI's impact on MST BI and acceptance, particularly within the Chinese elderly population, urging MST researchers to prioritize elderly attitudes for effective technological integration in healthcare.

Resection of malignant lesions in the oral and maxillofacial area causes functional and morphological defects. To recover from these defects, reconstruction surgery is needed such as a primary closure or a flap. There are advantages and disadvantages to the method of using the primary closure and the flap, and the choice of procedure is entirely up to a surgeon. The purpose of this study is to evaluate availability of primary closure in patients. For 10 years from January 2010 to May 2020, patients who recovered using flaps after removing malignant lesions from the oral cavity and those who closed the lesion using primary closure were investigated. The investigation was conducted by searching the database of the hospital. There were 85 patients who removed malignant lesions in the oral and maxillofacial area, and among them 16 patients closed the soft tissue defects using primary closure. Operation time, histologic types, stages, wound status, and period of hospitalization according to the patients' medical records were investigated retrospectively. Between the staging and the primary closure, statistically significant differences were observed between stage I and stage II patients in 13 patients using the primary closure. (P=0.046). Statistically significant differences were identified between operation time and primary closure, with an average of 4.02 hours (P=0.015). The average period of hospitality for patients who underwent primary closure was 13.4 days, compared to 26.7 days for those who underwent flap surgery. This difference was statistically significant (P=0.0003). This study evaluated the use of primary closure in patients who underwent resection of malignant lesions in the oral and maxillofacial area. Although the majority of patients underwent reconstruction with flaps, our results showed that primary closure can be a viable option for certain patients with early-stage lesions. Therefore, oral and maxillofacial surgeons should carefully consider various evaluation criteria and select appropriate reconstruction methods to optimize functional and aesthetic outcomes for each patient.

Regulatory macrophages (Mregs) are unique in that they have anti-inflammatory and immunosuppressive properties. Thus, treating inflammatory diseases using Mregs is an area of active research. Human Mregs are usually generated by culturing peripheral blood monocytes stimulated by macrophage colony-stimulating factor with interferon (IFN)-. Here, we generated Mregs with an elongated cell morphology from THP-1 cells stimulated with phorbol 12-myristate 13-acetate and cultured with arginylglycylaspartic acid and vitamin D3. These Mregs regulated macrophage function, and respectively downregulated and upregulated the expression of pro-inflammatory and immunosuppressive mediators. They also expressed Mregs-specific marker, such as dehydrogenase/reductase 9, even when exposed to inflammatory stimulants such as IFN-, lipopolysaccharide, purified xenogeneic antigen, and xenogeneic cells. The Mregs also exerted anti- inflammatory and anticoagulatory actions in response to xenogeneic cells and immunosuppressive effects on mitogen-induced Jurkat T-cell proliferation. Our method of generating functional Mregs in vitro without cytokines is simple and cost-effective.

This study aimed to conduct importance-performance analyses (IPAs) based on the perception of Korean middle-school students toward health management awareness during the post-coronavirus disease 2019 (COVID-19) era. Data were collected from 867 Korean middle-school students via online and offline surveys between May and June 2023. A frequency analysis, a reliability analysis, an IPA based on the entire target students, and an IPA depending on sex were carried out with the collected data, and they revealed the following. First, the IPA results regardless of sex indicated that four factors of the mental health were located in the third quadrant with one factor of the same variable in the fourth quadrant. The three factors of the disease management were located in the third quadrant. As for physical activity, two factors were located in the first quadrant, one in the second quadrant, and one in the third quadrant. As for sleep management, two factors were located in the second quadrant, one in the third quadrant, and one in the first quadrant. As for the eating management, two factors were located in the third quadrant, and one in the fourth quadrant. As for the social distancing variable, all four factors were located in the third quadrant. As for the hygiene management, two factors were located in the first quadrant, one in the third quadrant, and one in the fourth quadrant. Furthermore, the IPA results indicated gender differences in regular sports and vigorous movement activities associated with the physical activity. Additionally, a gender difference was observed in regular diet associated with the eating management. This study proposed possible measures for encouraging adolescents to recognize the importance of health and increase their health-related performance during the COVID-19 endemic phase.

Due to the long duration and high cost of traditional pumping tests, the response of well water level to seismic wave, earth tide, and barometric pressure provides a feasible method for determining continuous changes in aquifer hydraulic parameters. Aiming at the problem that the response phase shift of well BB water level to tidal tide M2 is greater than that of tide O1, this paper preferentially calculated the time series changes of S, Be, n and BKu based on the response mechanism of well water level to barometric pressure and earth tide and with the help of smooth moving method. Then by using the mixed flow model, the variation of transmissivity and leakage coefficient over time were simultaneously obtained, and the evolution process and characteristics of aquifer parameters near well BB caused by the Wenchuan earthquake were ultimately discussed. The calculation results are basically consistent with the previous pumping test, and have been verified and compared by using other scholars' methods. This solving process avoids the problems such as excessive dependence on initial values, multiple solutions, and unstable tide O1, which has a promoting effect on the study of the impact of seismic activity on aquifer systems.

This paper presents the findings of an exploratory study on the continuously generating Big Data on Twitter related to the sharing of information, news, views, opinions, ideas, knowledge, feedback, and experiences about the COVID-19 pandemic, with a specific focus on the Omicron variant, which is the globally dominant variant of SARS-CoV-2 at this time. A total of 12028 tweets about the Omicron variant were studied, and the specific characteristics of tweets that were analyzed include - sentiment, language, source, type, and embedded URLs. The findings of this study are manifold. First, from sentiment analysis, it was observed that 50.5% of tweets had the ‘neutral’ emotion. The other emotions - ‘bad’, ‘good’, ‘terrible’, and ‘great’ were found in 15.6%, 14.0%, 12.5%, and 7.5% of the tweets, respectively. Second, the findings of language interpretation showed that 65.9% of the tweets were posted in English. It was followed by Spanish or Castillian, French, Italian, Japanese, and other languages, which were found in 10.5%, 5.1%, 3.3%, 2.5%, and <2% of the tweets, respectively. Third, the findings from source tracking showed that “Twitter for Android” was associated with 35.2% of tweets. It was followed by “Twitter Web App”, “Twitter for iPhone”, “Twitter for iPad”, “TweetDeck”, and all other sources that accounted for 29.2%, 25.8%, 3.8%, 1.6%, and <1% of the tweets, respectively. Fourth, studying the type of tweets revealed that retweets accounted for 60.8% of the tweets, it was followed by original tweets and replies that accounted for 19.8% and 19.4% of the tweets, respectively. Fifth, in terms of embedded URL analysis, the most common domains embedded in the tweets were found to be twitter.com, which was followed by biorxiv.org, nature.com, wapo.st, nzherald.co.nz, recvprofits.com, science.org, and other URLs. Finally, to support similar research and development in this field centered around the analysis of tweets, we have developed an open-access Twitter dataset that comprises tweets about the SARS-CoV-2 omicron variant since the first detected case of this variant on November 24, 2021.

Alzheimer's disease (AD) is characterized by memory impairment and existence of amyloid-β (Aβ) plaques and neuroinflammation. Due to the pivotal role of oxidative damage in AD, natural antioxidative agents, such as polyphenol-rich fungi, have garnered scientific scrutiny. Here, the aqueous extract of mixed medicinal mushroom mycelia (MMMM) - Phellinus linteus, Ganoderma lucidum, and Inonotus obliquus - cultivated on a barley medium, was assessed for its anti-AD effects. A neuron-like PC12 cells, which were subjected to Zn2+, an Aβ aggregator, was employed as an in vitro AD model. The cells pretreated with or without MMMM assayed for Aβ immunofluorescence, cell viability, reactive oxygen species (ROS), apoptosis, and antioxidant enzyme activity. 5XFAD mice were administered with 30 mg/kg/day MMMM for 8 weeks and underwent memory function tests and histologic analyses. In vitro results demonstrated that the cells pretreated with MMMM exhibited attenuation in Aβ immunofluorescence, ROS accumulation, and apoptosis, and increment in cell viability and antioxidant enzyme activity. In vivo results revealed that 5XFAD mice administered with MMMM showed attenuation in memory impairment and histologic deterioration such as Aβ plaques accumulation and neuroinflammation. MMMM might mitigate AD-associated memory impairment and cerebral pathologies, including Aβ plaque accumulation, and neuroinflammation, by impeding Aβ-induced neurotoxicity.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

The traditional Simultaneous Localization and Mapping (SLAM) systems are based on the 1 strong static assumption, and their performance will degrade significantly due to the presence of 2 dynamic objects located in dynamic environments. To decrease the effects brought by the dynamic 3 objects, based on ORB-SLAM2 system framework, a novel dynamic semantic SLAM system called 4 MOR-SLAM is presented using mask repair method, which can accurately detect dynamic objects 5 and realize high-precision positioning and tracking of the system in dynamic indoor environments. 6 First, an instance segmentation module is added to the front end of ORB-SLAM2 to distinguish 7 dynamic and static objects in the environment and obtains a preliminary mask. Next, to overcome the 8 under-segmentation problem in instance segmentation, a new mask inpainting model is proposed to 9 ensure that the integrity of object masks, which repairs large objects and small objects in the image 10 with depth value fusion method and morphological method respectively. Then, a reliable basic matrix 11 can be obtained based on the above repaired mask. Finally, the potential dynamic feature points 12 in the environment are detected and removed through the reliable basic matrix, and the remaining 13 static feature points are input into the tracking module of the system to realize the high-precision 14 positioning and tracking in dynamic environments. The experiments on the public TUM dataset 15 show that, compared with ORB-SLAM2, the MOR-SLAM improves the absolute trajectory accuracy 16 by 95.55%. In addition, compared with DynaSLAM and DS-SLAM on the high-dynamic sequences 17 (fr3/w/rpy and fr3/w/static), the MOR-SLAM improves the absolute trajectory accuracy by 15.20% 18 and 59.71%, respectively

The PI3K/mTOR signalling pathway plays a central role in the governing of cell growth, survival and metabolism. As such, it must integrate and decode information from both external and internal sources to guide efficient decision-making by the cell. To facilitate this, the pathway have evolved an intricate web of complex regulatory mechanisms and elaborate crosstalk with neighbouring signalling pathways, making it a highly non-linear system. Here, we describe the mechanistic biological details that underpin these regulatory mechanisms, covering a multitude of negative and positive feedback loops, feed-forward loops, competing protein interactions, and crosstalk with major signalling pathways. Further, we highlight the non-linear and dynamic network behaviours that arise from these regulations, uncovered through both computational and experimental studies. Given the pivotal role of the PI3K/mTOR network in cellular homeostasis and its frequent dysregulation in pathologies including cancer and diabetes, a coherent and systems-level understanding of the complex regulation and consequential dynamic signalling behaviours within this network is imperative for advancing biology and development of new therapeutic approaches.

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

This study analyzes the effect of economic growth and income distribution on health inequality using data from the Organization for Economic Cooperation and Development (OECD). A panel analysis was conducted by combining 21 years of data (from 2000 to 2020) from 38 OECD countries. Life expectancy and avoidable mortality were set as the dependent variables; gross domestic product and poverty gap were set as the independent variables; body mass index, consumption, smoking rate, healthcare personnel, number of beds in health service facilities, national medical expenses, and unemployment were set as control variables. First, economic growth and poverty gap significantly affect life expectancy and avoidable mortality. It has been confirmed that to resolve health inequality, growth during growth and distribution must be prioritized. Second, it has been confirmed that as the poverty gap increases, life expectancy increases and the avoidable mortality rate decreases. A mechanism different from the existence of a medical security system targeting the lowest class or an increase in the welfare of society worked. In conclusion, as a policy proposal to alleviate health inequality, this study suggests that policy intervention is necessary to block or alleviate the negative impact of income inequality in health care policies.

Species have shown their habital variations in responding to climate change, especially during the spring and summer spawning seasons. The species distribution model (SDM) is considered the most favorable tool to study the potential effects of climate change on species distribution. Therefore, we developed the ensemble SDM to predict the changes in species distribution of Portunus trituberculatus among different seasons in 2050 and 2100 under the climate scenarios RCP4.5 and RCP8.5. The results of SDM indicate that the distribution of this species will move northward and have obviouse seasonal variations. Meanwhile, the suitable habitat for the species will be significantly reduced in summer, with loses rates ranging from 45.23% (RCP4.5) to 88.26% (RCP.8.5) by 2100s. Habitat reduction will mainly occur in the East China Sea and southern part of the Yellow Sea, while there will be a small increase in the northern Bohai Sea. These findings will be important to manage the ecosystem and fishery, provide an information forecast of this species in the future, and maintain species diversity if the seawater temperature rises.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

The pharmacological effects of the fruiting body of Ophiocordyceps sinensis (Os) exerted antioxidant, anti-virus, and immunomodulatory, whereas the anti-inflammatory effects and active components of Os mycelial submerged culture (OMSC) are not known. This study aimed to investigate the active compounds in the fermented liquid (FLOS), hot water (WEOS), and 50-95% (EEOS-50, EEOS-95) ethanol extracts of OMSC and their anti-inflammatory effects and potential mechanisms in LPS-stimulated microglial BV2 cells. The results demonstrated that all of the OMSC extracts could inhibit NO production in BV2 cells. EEOS-95 exhibited the strongest inhibitory effects (41 % inhibitory ability at 500 µg/mL), and its ergosterol, GABA, total phenolic, and total flavonoid contents were significantly higher than those of the other extracts (18.60, 18.60, 2.28, and 2.14 mg/g, p &lt; 0.05, respectively). EEOS-95 also has a strong inhibitory ability against IL-6, IL-1β and TNF-α with IC50 of 617, 277 and 507 µg/mL, respectively, which is higher than that of 1 mM melatonin. The anti-inflammatory mechanism of EEOS-95 seems to be associated with up-regulation of PPAR-γ/Nrf-2/HO-1 antioxidant-related expression and down-regulation of NF-κB/COX-2/iNOS pro-inflammatory expression signaling. Therefore, we hypothesized that EEOS-95 can prevent neurodegenerative diseases, but the effect on the application in vivo should be further investigated.

Hepatocellular Carcinoma is one of the most predominant malignancies with high fatality rate and is rising at an alarming rate because it is quite resistant to radioand chemotherapy. The proliferation, migration and activation of endothelial cells are involved in tumor occurrence and development. Indirubin is the major active anti-tumor ingredient of a traditional Chinese herbal medicine. In this research, Td-ECs were derived from human umbilical vein endothelial cells (HUVECs) by treating HUVECs with the conditioned medium of human liver cancer cell line HepG2. The effects of indirubin on cell proliferation, migration, invasion and angiogenesis of Td-ECs were assessed. Indirubin significantly inhibited Td-EC cell proliferation in a dose- and time-dependent manner. Indirubin also inhibited Td-EC migration and angiogenesis. However, indirubin’s effects on HUVECs were weaker than on Td-ECs.

In February 2004, the Food and Drug Administration (FDA) was the first to approve the combination of cisplatin (CDDP) and pemetrexed (PEM) as standard first-line chemotherapy for untreated, unresectable malignant pleural mesothelioma (MPM). However, after that approval, no progress was made in the standard first-line treatment of MPM for almost 15 years. Positive results from a phase 3 study (Mesothelioma Avastin Cisplatin Pemetrexed Study: MAPS) verifying the effect of bevacizumab, an anti-angiogenesis agent added to CDDP/PEM for unresectable MPM, were published in The Lancet in December 2015; however, this did not lead to approval by national drug regulatory agencies. Furthermore, no second-line treatment was established for cases refractory to CDDP/PEM. In August 2018, the Pharmaceuticals and Medical Devices Agency of Japan was the first in the world to approve monotherapy with nivolumab, an immune checkpoint inhibitor (ICI), for previously unresectable, advanced, or recurrent MPM. Following Japan, in October 2020, the FDA approved the combination of nivolumab and ipilimumab for the treatment of previously untreated, unresectable MPM. In this article, we review the transition of drug treatment for MPM, in light of the historical background, focusing on the benefits of ICIs.

The extant Keteleeria is endemic to East and Southeast Asia, while it is widely distributed in the northern hemisphere in Earth’s history. In this paper, we reported a novel wood fossil of Keteleerioxylon changchunense Shi, Sun, Meng et Yu sp. nov. collected from the middle member of Yingcheng Formation, Yingcheng Coal Mine, Changchun City, Jilin Province, Northeast China. The quantitative growth-ring analyses of K. changchunense indicate that it was evergreen and its leaf longevity was 1-3 years, which is consistent with the foliar retention of extant Keteleeria. Its high ring markedness index (RMI) indicates that the climate seasonality was pronounced during the early Albian in Songliao Basin, Northeast China. The fossil records of Keteleeria and closely related taxa indicate that this group might originate in Northeast China, spread and migrated northward during the Cretaceous, gradually decreased in the Cenozoic, and so far only survives in East and Southeast Asia.

The critical period (CP) phenomenon in language development ranks among the 125 conundrums facing scientists in the 21st century, according to Science. While the phenomenon itself has been noncontroversial in first language acquisition, it still warrants an adequate explanation. Predicated on language acquisition as a complex process, questions among the first to be raised include: How do children accomplish this remarkable feat in such a short amount of time? And how do nature and nurture come together to influence language learning? In second language acquisition, however, both the notion of CP, albeit popular, and its empirical evidence have remained contested to this date - among the questions, whether the observed evidence counts as CP-specific and/or whether or not it warrants an isomorphic attribution to maturational constraints. Entwined in this debate are two well-established facets of inter-learner differential attainment. The first is that there exists a stark difference in ultimate attainment between younger and older learners. A second facet is the vast differences in ultimate attainment among older learners. In this article, adopting a social physics approach, we mathematically establish both the relationship between nature and nurture contributions and the presence of a critical period, and, at once, tender a parsimonious and probable theory for the twin phenomena of inter-learner differential attainment.

Current COVID-19 vaccines can effectively reduce disease severity and hospitalisation; however, they are not considerably effective in preventing infection and transmission. In this context, mucosal vaccines are pertinent to prevent SARS-CoV-2 infection and spread. In this study, we generated a replication-competent recombinant chimeric influenza A virus (IAV) expressing the receptor-binding domain (RBD) of SARS-CoV-2 prototype in the C-terminus of the neuraminidase (NA) of A/Puerto Rico/08/1934 H1N1 (PR8). The remaining seven segments from A/WSN/1933 H1N1 (WSN) were named PR8NARBD/WSN. We observed that the recombinant virus with the WSN backbone demonstrated improved expression of NA and RBD. A single intranasal dose of PR8NARBD/WSN in mice generated robust mucosal immunity, neutralising antibodies, cellular immunity, and tissue-resident memory T cells specific to SARS-CoV-2 and IAV. Importantly, immunisation with PR8NARBD/WSN viruses effectively protected mice against lethal challenges with H1N1, H3N2 IAV, and SARS-CoV-2 Beta variant and significantly reduced lung viral loads. Overall, our research demonstrates the promising potential of PR8NARBD/WSN as an attractive vaccine against emerging SARS-CoV-2 variants and influenza A virus infections.

Since large articulated vehicles have uncertainties in trailer articulation angle as well as dynamic complexity, it is not easy to accurately establish a reliable motion plan. In this paper, two geometric path plans constructed based on the empirical rules of driving experts are presented so that articulated vehicles can automatically perform perpendicular parking on a reverse path. By analyzing the empirical parking methods of professional drivers, these path plans were constructed by appropriately combining several standardized simple basic motions to facilitate implementation in real vehicles. In addition, path plans included appropriate complementary motions to effectively respond to uncertainties arising from articulation angles, etc. The complementary motions developed in this study are based on the results of qualitative analysis on the behavior of articulated vehicles. The usefulness of the proposed articulated vehicle parking method has been proven through hundreds of experimental tests using a 1:10 ratio model automated vehicle.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

With the trend of public infrastructure becoming more sustainable, large multi-purpose sports venues (LMPSVs) have become one of the world's most complex architectural projects and one of the landmark buildings of an international city. LMPSVs will lead the world in sustainable design, construction and operational innovations, and play a crucial role in raising awareness of sustainability around the world. System Thinking (ST), System Dynamics (SD) and Sustainable System Development (SSD) theories are three interrelated concepts that together form a methodological framework for solving complex system problems and driving strategies. The purpose of this study is to examine how LMPSVs can implement environmental, social, governance, and innovation (ESGI) enterprise transformation strategy (ETS) based on a sustainable systems development (SSD) framework. In view of the current global environmental challenges and social responsibility requirements, the motivation of this study is to provide an integrated transformation pathway for LMPSVs to achieve the goal of sustainable development and to contribute to the field of related disciplines. The methodology of this research adopts a combination of literature review and case study analysis, and the theoretical basis is mainly drawn from cutting-edge research in the fields of sustainable development, corporate social responsibility (CSR) and environmental management. Then, by analyzing successful transformation cases in China, we extract data and information to explore the application and effectiveness of these strategies in practice. The results of the study show that by implementing ESGI-based transformation strategy, LMPSVs can not only make significant progress in terms of environmental protection, social responsibility, and governance structure, but also drive long-term corporate growth and competitiveness through innovation. Specifically, these results are realized in terms of increased efficiency in energy use, improved waste management, community involvement and increased stakeholder satisfaction. The study concludes by emphasizing that the SSD-based ESGI Transformation Strategic framework provides a sustainable pathway for LMPSVs. In the future, the extension of this transformation strategy will help a wider range of industry sectors to achieve sustainable development goals, and has wide application potential and far-reaching social significance.

Genetic diversity is the foundation of evolutionary resilience, adaptive potential, and the flourishing vitality of living organisms, serving as the cornerstone for robust ecosystems and the continuous evolution of life on Earth. The landscape of directed evolution, a powerful biotechnological tool inspired by natural evolutionary processes, has undergone a transformative shift propelled by innovative strategies for generating genetic diversity. This shift is fuelled by several factors, encompassing the utilization of advanced toolkits like CRISPR-Cas and base editors, enhanced comprehension of biological mechanisms, cost-effective custom oligo pool synthesis, and the seamless integration of artificial intelligence and automation. This comprehensive review looks into the myriad methodologies employed for constructing gene libraries, both in vitro and in vivo, categorized into three major classes: random mutagenesis, focused mutagenesis, and DNA recombination. The objectives of this review are threefold: firstly, to present a panoramic overview of recent advances in genetic diversity creation, secondly, to inspire novel ideas for further innovation in the genetic diversity generation, and thirdly, to provide a valuable resource for individuals entering the field of directed evolution.

Demand for development of the convergence industry, research studies on electrical conductivity, thermal characteristics, semiconductors, motors, and batteries using special materials have come to the fore. Meanwhile, molybdenum (Mo) exhibits relatively small inorganic qualities, and the thermal conductivity rate is applied to various fields. In this study, in-depth characteristics were considered regarding the concentration of thermal characteristics, IR car terminal characteristics, and IR ve-hicles. This study calculated each phase temperature of the molybdenum sputtered specimens in the steady state according to the heat transfer theory. When the molybdenum-sputtered fabric’s metal layer pointed to the outside air, the heat transfer rate (Q) was high at 5748.3W, In contrast, if the molybdenum sputtered film’s metal layer of the pointed toward the heat source, the heat transfer rate (Q) was low at 187.1W. As a result of measuring the IR transmittance, the infrared transmit-tance of the molybdenum sputtering-treated sample was significantly reduced compared to the untreated sample. In the case of untreated samples, the transmittance ranged from 92.7 to 42.0%. When only the cross part was treated with molybdenum sputtering and the molybdenum surface was directed toward the IR irradiator, the IR transmittance was 66.8~0.7%. It is believed that the molybdenum sputtering polyamide samples produced in this study can be applied to multifunc-tional military wear, biosignal detection sensors, semiconductor products, batteries, etc., by utilizing excellent electrical properties, stealth functions, IR blocking properties, and lightness for infrared thermal imaging detectors.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

Blood image intensity has been used to detect erythrocyte sedimentation rate (ESR). However, it does not give an information on biophysical properties of blood sample under continuous ESR. In this study, three physical properties, including, τ₀, ESR_τ, and AI_I, are suggested to quantify mechanical variations of blood under continuous ESR. To demonstrate the proposed method, blood sample is loaded into a driving syringe. The blood flow rate is set in a periodic on–off pattern. Blood sample is then supplied into a capillary chip, and microscopic blood images are captured at specific intervals. Blood shear stress is quantified from the interface of blood stream in the coflowing channel. Both τ₀ and ESR_τ are then obtained by analyzing the blood shear stress. Simultaneously, the AI_I is evaluated by analyzing the image intensity of blood flow. According to the experimental results, the τ₀ exhibits consistent trends with respect to hematocrit as well as diluent. The ESR_τ and AI_I showed a reciprocal relationship each other. Three suggested properties represented substantial differences for suspended blood samples (i.e., hardened red blood cells, different concentration of dextran solution and fibrinogen). In conclusion, the present method can detect variations of blood sample under continuous ESR effectively.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

In this letter we investigate if SARS-CoV-2 RNA is involved in the increased ageing of alveolar cells. Our in silico study is explorative. With the results we are able to outline experiments with AEC2 repair of bleomycin damaged alveolar cells. If AEC2 repair capability is diminished by spike RNA then perhaps this result provides a first step on a route to treat immortal lung cancer cells.

This study aims to test a model linking destination image, perceived value, tourist satisfaction, and tourist loyalty. Based on a sample of 300 tourists travelling by car from the World Natural Heritage Site of Tianchi, China, a new model of destination image was explored and data were analysed using partial least squares structural equation modelling (PLS-SEM). The results show that perceived value and satisfaction are direct antecedents of destination loyalty. Above all, perceived value and tourist satisfaction mediate the relationship between destination image and loyalty. Finally, this study discusses the theoretical and management implications of the findings in order to boost the tourism industry in the context of car trips.

Water resources provided by alpine glaciers are an important pillar for people living in the arid regions in the west of China. In this study, the HBV (Hydrologiska Byrans Vattenavdelning) light model was applied to simulate glacier mass balance and runoff in the Koxkar River Basin (KRB) on the south slope of Mt. Tumur, western Tianshan Mts.. Daily temperature and precipitation were calculated by multiple linear regressions and gradient-inverse distance weighting, respectively, based on in-situ observed data by automatic weather stations (AWSs) in the basin (2007–2009) and at four meteorological stations neighbering the basin (1959–2009). Observed daily air temperature and precipitation were taken as input data for the HBV model, which was calibrated using runoff in 2007/08 and 2009/10, and validated in 2008/09 and 2010/11. Generally, the model could simulate runoff very well. The annual glacier mass balance and runoff were calculated using the HBV model driven by interpolated meteorological data for the period of 1959–2009. The simulated glacier mass balance were reasonable when compared with those observed values at nearby glaciers, indicating a decrease trend of mass balance in the basin with an average value of –370.4 mm a^-1 since 1959. The annual runoff showed a slight increase trend (5.51 mm a^-1). Futher analysis indicated that the runoff is more sensitive to temperature than precipitation amuont in the Koxkar river basin.

Searching over a sorted list is a classical problem in computer science. Binary Search takes at most log2n+1 tries to find an item in a sorted list of size n. Interpolation Search achieves an average time complexity of Ο(loglogn) for uniformly distributed data. Hybrids of Binary Search and Interpolation Search are also available to handle data with unknown distributions. This paper analyzes the computation cost of these methods and shows that interpolation can significantly affect their performance — accordingly, a new method, Interpolation Once Binary Search (IOBS), is proposed. The experimental results show that IOBS outperforms the hybrids of Binary Search and Interpolation Search for nonuniformly distributed data.

There are several causes of hypoxia during and after surgery, and atelectasis is a common symptom that occurs during surgery. In particular, elderly patients are more vulnerable to hypoxia due to their existing lung diseases or respiratory muscle weakness. This study presents the cases of two elderly patients who developed hypoxia during total hip arthroplasty under general anesthesia. Positive end expiratory pressure, recruitment maneuver, and increased fraction of inspired oxygen improved hypoxia only temporarily, and patients’ oxygen saturation level again dropped to 79%–80%. We suspected that hypoxia was caused by atelectasis and, therefore, re-sumed spontaneous respiration. Thereafter, both the patients showed an improvement in hypoxia. Intraopera-tive hypoxia that is suspected to be caused by atelectasis can be improved by securing sufficient lung volume for respiration through increased muscle tone with spontaneous respiration

Background and Objectives: Cancer as the second leading cause of death in the United States poses a huge healthcare burden. Barriers to access to advanced therapies influence the outcome of cancer treatment. In this study, we examined whether insurance types affect the quality of cancer clinical care regarding access to an important monoclonal antibody, ramucirumab. Materials and Methods: Data for 13,340 cancer patients with Purchased or Medicaid insurance from the All of Us Database were collected for this study. The Chi-square test of proportions was employed to determine the significance of patient cohort characteristics and ramucirumab usage between Purchased and Medicaid insurance groups. The independent t-test was utilized to assess the influences of other determinants on insurance types. Results: Cancer patients who are African American, with lower socioeconomic status, or with lower educational attainment are more likely to be insured by Medicaid. Analysis of survey questions demonstrated the relationship between income and education level with insurance type as Medicaid cancer patients were less likely to receive primary care and specialist physician access and more likely to request lower cost medications. In addition, those with Medicaid insurance were identified to have poorer access to expensive therapeutics like ramucirumab compared to those with Purchased insurance.  Conclusions: The inequities of the US healthcare system are observed for cancer patient care; access to physicians and therapeutics are highly varied and dependent on insurance types. Socioeconomic status determines insurance type, which unfortunately generates a significant impact on cancer treatment and disease outcome.

Considering the spectrum shortage problem of IoT devices, we introduce a collaborative spectrum sensing (CSS) framework in this paper to identify available spectrum resources, so that IoT devices can access it and meanwhile avoid causing harmful interference to the normal communication of the primary user (PU). However, in the process of the PU’s signal detection in IoT devices, the issue about the stopping time and decision cost arises. To this end, we propose a distributed cognitive IoT model, which includes two IoT devices independently using sequential decision rules to detect the PU. On this basis, we define the stopping time and cost function for IoT devices, and formulate an average cost optimization problem in CSS. To solve this problem, we further regard the optimal stopping time problem as a finite horizon problem, and solve the threshold of the optimal decision rule by dynamic programming. At last, numerical simulation results demonstrate the correctness of our proposal in terms of the global false alarm and miss detection probability, and it always achieves minimal average cost under various cost of each observation taken and thresholds.

Appetitive traits have been associated with eating behaviors and weight in youth. However, the relationships among adults have received less attention. In this study, we measured appetitive traits among 520 female college students from a University in eastern Chinese using the Chinese translated Adults Eating Behavior Questionnaire (C-AEBQ) and found that two food approach traits (food enjoyment and emotional over-eating) were positively while two food avoidance traits (slowness in eating and satiety responsiveness) were negatively associated with BMI. Individual trait was differentially associated with eating behaviors. Specifically, a positive correlation was found between food responsiveness and higher frequency of selecting delivery food, spicy food, and sugared beverage; conversely, satiety responsiveness was associated with higher frequency of skipping meals. Using latent profile analysis, participants were classified into four appetitive patterns: food approacher, food approacher with emotional under-eating, food avoider, and food avoider with emotional over-eating. Food avoiders had significant lower BMI and higher proportion of underweight than other three patterns. Compared to food approacher, food avoiders had higher frequency of skipping breakfast, and food avoiders with emotional over-eating had higher frequency of skipping both breakfast and lunch. No significant differences were observed in food choice and dieting behavior among four appetitive patterns. The findings suggested a correlation between an individual’s appetitive pattern and eating behaviors among female college students, those with food avoidance patterns are more likely to have irregular meals, which may contribute to their low BMI. The findings provide valuable insights for female college students to cultivate a healthy eating behavior and sustain a healthy body weight.

Oleuropein, glycosylated secoiridoid present in olive leaves is known to be an important antioxidant phenolic compound. We studied the antioxidant effect of low doses of oleuropein aglycone (3,4-DHPEA-EA) and oleuropein aglycone peracetylated (3,4-DHPEA-EA(P)) in murine C2C12 myocytes treated with hydrogen peroxide (H2O2). Both compounds were used at a concentration of 10 μM and were able to inhibit cell death induced by the H2O2 treatment, with 3,4-DHPEA-EA(P) being more. Under our experimental conditions, H2O2 efficiently induced the phosphorylated-active form of JNK and of its downstream target c-Jun. We demonstrated, by Western blot analysis, that 3,4-DHPEA-EA(P) was efficient in inhibiting the phospho-active form of JNK. This data suggests that the growth arrest and cell death of C2C12 proceeds via the JNK/c-Jun pathway. Moreover, we demonstrated that 3,4-DHPEA-EA(P) affects the myogenesis of C2C12 cells; because MyoD mRNA levels and the differentiation process are restored with 3,4-DHPEA-EA(P) after treatment. Overall, the results indicate that 3,4-DHPEA-EA(P) prevents ROS-mediated degenerative process in a genomic and epigenomic manner by functioning as an efficient antioxidant.