Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

The object of this study was to discover an alternative therapeutic agent with fewer side effects against acne vulgaris, which is one of the most common skin diseases. Acne vulgaris often associates with acne-related bacteria such as <i>Propionibacterium acnes</i>, <i>Staphylococcus epidermidis</i>, <i>Staphylococcus aureus</i> and <i>Pseudomonas aeruginosa</i>, some of which exhibit a resistant against commercial antibiotics used in the treatment of acne vulgaris (tetracycline, erythromycin, and lincomycin). In the current study, we evaluated <i>in vitro</i> antibacterial activity of chitosan-phytochemical conjugates against acne-related bacteria. Three of chitosan-phytochemical conjugates used in this study showed stronger antibacterial activity than that of chitosan (unmodified control). Chitosan-caffeic acid conjugate (CCA) exhibited the highest antibacterial activity against acne-related bacteria with minimum inhibitory concentration values of 8 μg/mL to 256 μg/mL. In addition, the MICs of antibiotics against antibiotic resistant <i>P. acnes</i> and <i>P. aeruginosa</i> strains were dramatically reduced in the combination with CCA, suggesting that CCA would restore the antibacterial activity of the antibiotics. The analysis of fractional inhibitory concentration indices clearly revealed a synergistic antibacterial effect between CCA and the antibiotics. Thus, the median ∑FIC values against the antibiotic resistant bacterial strains were ranged from 0.375 to 0.533 in the combination mode of CCA and antibiotics.

The differentiation between Neuromyelitis optica spectrum disorder (NMOSD) and cervical spondylotic myelopathy (CSM) is necessary, because both diseases have similar symptoms, such as motor weakness and sensory disturbances. The challenge arises when NMOSD presents with short-segment spinal cord lesions, which can mimic the clinical presentation of CSM. This case report presents an NMOSD misdiagnosed as CSM. A 66-year-old woman presented with neck pain, left arm pain, and motor weakness. She was initially diagnosed with CSM based on MRI findings that revealed the increased signal intensity of the spinal cord at the C3 to 4 levels and underwent surgery. Three years later, she had sudden left upper extremity motor weakness and mild gait disturbance. Physical exam showed left-side weakness and altered reflexes, with longitudinally extensive transverse myelitis (LETM) findings on cervical MRI. The CSF study revealed a 2+ AQP4-Ab finding. Finally, NMO was diagnosed. Steroid pulsed therapy and immunosuppression therapy led to improved motor function and gait after 20 days. We present a case report of a NMO patient who initially exhibited clinical and radiological features CSM but was later diagnosed with NMO. This case underscores the diagnostic challenge in distinguishing NMO from CSM, especially in elderly patients who commonly experience spinal degeneration leading to cord compression and associated cord signal changes on MRI. The misinterpretation or confusion with transverse myelitis can occur as a result. This case highlights the importance of considering NMO as a potential differential diagnosis in elderly patients with spinal degeneration, emphasizing the significance of precise and timely diagnosis for guiding optimal treatment decisions.

In recent years, bone tissue engineering (BTE) has made significant progress in promoting the direct and functional connection between bone and graft, including osseointegration and osteoconduction, to facilitate the healing of damaged bone tissues. Herein, we introduce a new, environmentally friendly, and cost-effective method for synthesizing reduced graphene oxide (rGO) and hydroxyapatite (HAp). The method uses epigallocatechin-3-O-gallate (EGCG) as a reducing agent to synthesize rGO (E-rGO), and HAp powder is obtained from Atlantic bluefin tuna (Thunnus thynnus). The physicochemical analysis indicated that the E-rGO/HAp composites had exceptional properties for use as BTE scaffolds, as well as high purity. Moreover, we discovered that E-rGO/HAp composites facilitated not only proliferation, but also early and late osteogenic differentiation of human mesenchymal stem cells (hMSCs). Our work suggests that E-rGO/HAp composites may play a significant role in promoting the spontaneous osteogenic differentiation of hMSCs, and we envision that the E-rGO/HAp composites could serve as promising candidates for BTE scaffolds, stem cell differentiation stimulators, and implantable device components due to their biocompatible and bioactive properties. Overall, we suggest a new approach for developing cost-effective and environmentally friendly E-rGO/HAp composite materials for BTE application.

The aim of this study is to evaluate the optimal conditions of membrane filtration process. Both laboratory test and pilot-scale test were conducted to examine a treated water on blending water. The water sample were prepared by blending a raw water and the effluent water filtered through an organic membrane. The optimal efficiency in the treatment of water quality at the lab-scale test was generated under conditions of flux at 2.0 m³/m²∙day, the blending ratio of 4:1, and the optimal dosage of coagulant at 20 ppm. The pilot-scale test resulted in that the optimal efficiency was obtained under conditions of flux at 2.0 m³/m²∙day and the blending ratio of 6.0:1. However, the different results between lab-scale and pilot-scale tests on the optimal dosage of coagulant implied that it is difficult to achieve the stable condition of process operation at the low level of coagulant. In summary, the results indicated that, in the combination process of organic membrane and ceramic membrane, the recovery efficiency was achieved above the level of 98.4 %. Compared to 92.1 % in a single organic membrane process, the combination process is 6.3 % more efficient than the single one. This combination process of water treatment lead to stable recovery rates by the optimal input of dosage, less pollution load to water, and a stabilized filtration system.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

Energy and Environment Tax is used globally as a means of environment policy. Energy and Environment tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy and environmental taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy and environmental taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and to suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy and environmental taxes. Results of this study show that South Korea’s energy and environmental taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy and environmental tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy and environmental taxation. However, energy and environmental taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy and environmental taxation

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

This study aimed to improve sensitivity of ferrous particle sensors used in various mechanical systems such as wind power gearboxes to detect abnormalities by measuring the amount of ferrous wear particles generated by metal-to-metal contact. Existing sensors collect ferrous particles using a permanent magnet. However, its ability to detect abnormalities is limited because it only measures amounts of ferrous particles collected on the top of the sensor. To overcome this limitation, this study evaluated sensibility of an existing sensor using a multi-physics analysis method and improved it by changing the core shape inside the sensor. The detection ability of the improved sensor was analytically shown to be better than the existing sensor. This study highlights the use of analytical methods and multi-physics analysis for developing a ferrous particle sensor and presents a method to compare sensibility analytically. Results of the improved sensor are expected to enhance the ability to detect abnormalities in the lubrication system where ferrous wear particles are generated. This study will contribute to the development of more effective ferrous particle sensors, which can potentially improve the performance and reliability of mechanical systems.

In this study, the literature on varnish contamination is investigated among the various con-taminations of lubricant. As the period of use of lubricant increases, the lubricant deteriorates and becomes contaminated. The varnish causes filter plugging, sticking of hydraulic valves and fuel injection pumps, obstruction of flow, reduction of clearance, poor heater and cooler perfor-mance, and increase of friction and wear in various lubrication systems. These problems also cause mechanical system failure, performance degradation, and increased maintenance and re-pair cost. To improve the problems causes by the varnish, an adequate understanding of varnish is required. Therefore, in this literature review, definitions and characteristics, generating ma-chinery, generating mechanisms, causes, measurement methods, and prevention or removal methods are summarized. Most of the data are reports of companies related to lubricant and machine maintenance, and are included in some papers. We hope that this summary of varnish will be helpful to those who are engaged in reducing or preventing varnish problems.

Recently, due to the decrease in labor force, increase in labor costs, and the desire for improved quality of life, research on robots has been actively conducted to address these issues. However, it is currently difficult to find robots that physically interact with humans. The reason is that the actuators of robots do not have high torque density on their own. To solve this problem, high torque density motors, such as proprioceptive actuators, are being researched. However, the torque density is still insufficient for physical interaction with humans, so we have developed a motor with higher torque density. However, high torque density motors have the disadvantage of lower speed characteristics due to increased Back-EMF. Therefore, to address the deterioration of speed characteristics in the developed motor, we applied the Independent 3-Phase winding structure to improve the speed characteristics. Consequently, through comparison with Y-Connection and Delta-Connection, we propose the most suitable winding structure for high torque density motors intended for physical interaction with humans.

Epoxy was blended with benzoxazine resin and aluminum trihydrate (ATH) additive to render flame retardancy while maintaining mechanical properties. The ATH was modified using three different silane coupling agents and then added to 60/40 epoxy/benzoxazine mixtures. The effect of blend compositions and surface modification on flame retardant and mechanical properties of the composites was investigated by UL94, tensile, and shear tests. Resin mixtures containing more than 40 wt% benzoxazine revealed a UL94 V-1 rating with enhanced tensile and shear strength. Upon addition of 20 wt% ATH to 60/40 epoxy/benzoxazine, a V-0 rating was achieved. The lowered tensile and adhesive properties of the composites in the presence of ATH were improved by modifying the ATH surface using silane coupling agents.

Hepatocellular carcinoma (HCC) is currently the third leading cause of malignancy-related mortalities worldwide. Natural killer (NK) cells are involved in the critical role of first line immunological defense against cancer development. Defects in NK cell functions are recognized as important mechanisms for immune evasion of tumor cells. NK cell function appears to be attenuated in HCC, and many previous reports suggested that NK cells play a critical role in controlling HCC, suggesting that boosting the activity of dysfunctional NK cells can enhance tumor cell killing. However, the detailed mechanisms of NK cell dysfunction in tumor microenvironment of HCC remain largely unknown. A better understanding of the mechanisms of NK cell dysfunction in HCC will help in the NK cell-mediated eradication of cancer cells and prolong patient survival. In this review, we describe the various mechanisms underlying NK cell dysfunction in HCC. Further, we summarize current advances in the approaches to enhance endogenous NK cell function and in adoptive NK cell therapies, to cure this difficult-to-treat cancer.

Background and Objectives: High rates of psychiatric disorders and comorbidities have been reported in juvenile detainees which have been associated with repeat offenses. However, research on this topic has been limited to Asian countries. This study aimed to examine the prevalence of psychiatric disorders and sexual differences among juvenile detainees in a detention center in South Korea. Materials and Method: The participants comprised 54 males and 46 females, with a minimum intelligence score of 80. Psychiatric diagnosis was determined using the Mini-International Neuropsychiatric Interview for Children and Adolescents (MINI-KID). The Massachusetts Youth Screening Instrument-Version 2 (MAYSI-2) was used to investigate gender differences. Results: Using the MINI-KID, the most frequent diseases were conduct disorder (CD), alcohol dependence, suicidal tendency, attention-deficit/hyperactivity disorder (ADHD) with statistically significant differences between men and women. Only alcohol abuse was higher in men while the rest were higher in women. The items with a statistically significant gender difference in MAYSI-2, were alcohol/drug use, feeling depressed/anxious, somatic complaints, suicidal ideation, and traumatic experience. All items for which the gender difference was statistically significant were higher in the proportion of women. Conclusions: Juvenile detainees exhibit high rates of psychiatric disorders and comorbidities. CDs, alcohol dependence and ADHD are the most common psychiatric disorders among juvenile detainees in South Korea. Assessment of and intervention in psychiatric disorders may help prevent further offenses. These findings highlight the importance of diagnosing and intervening in psychiatric disorders within juvenile detention systems.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

This paper examines the moral community thesis in the secular context of China. Using multilevel logistic regression, we test (1) whether both individual- (measured by affiliation with institutional religion) and aggregate-level religiosity (measured by the number of religious sites per 10,000 people in province) are inversely related to law and rule violations at the individual level and (2) whether the province-level religiosity enhances the inverse relationship between individual religiosity and the deviant behaviors. Results from analyzing data from the 2010 China General Social Survey and the Spatial Explorer of Religions show that both individual- and aggregate-level religiosity are inversely related to the odds of violating the law and various rules of government, transportation, workplace, and other organizations. However, the cross-level interactions are not significant across models, indicating that the contextual religiosity does not increase the effect of individual-level religiosity on deviance. Implications of findings for the moral community thesis are discussed.

Background and Objectives: Although there has been growing interest in the association of ADHD with anxiety, depression, suicidal ideation, and self-esteem, there is a lack of consistent results and these associations remain unclear. This study investigated the differential patterns of anxiety, depression, suicidal ideation, and self-esteem with regard to the presence of ADHD. Materials and Methods: The subjects were divided into a patient group and a control group. The patient group included 49 patients diagnosed with ADHD at the department of psychiatry of one university hospital. For the control group, 3,727 students were invited to complete a questionnaire. Of the 1,717 students who responded to the questionnaire, 245 were selected for patient-controlled studies. All the subjects were instructed to complete the Beck Suicide Ideation Scale, Children's Depression Inventory, Beck’s Depression Inventory, State-Trait Anxiety Inventory, and Rosenberg Self-Esteem Scale. Results: ADHD subjects experienced more anxiety, depression, and suicidal ideation as well as lower self-esteem compared to the control group comprising participants without ADHD. Conclusions: These findings suggest that ADHD symptoms may contribute to greater suicidal ideation through experienced depression, anxiety, and low self-esteem in school-aged children. Therefore, appropriate ADHD symptom management is necessary to reduce suicidal ideation among school-aged children with ADHD symptoms.

Changes in coastal topography can affect the ecological environment and marine industries. In this study, we analyzed the patterns and causes of changes in shoreline and undersea topography in the Nakdong River estuary in the southeast of South Korea using depth and shoreline surveys of the estuary, as well as data on discharge, suspended sediments, and precipitation in the Nakdong River basin. The results showed that erosion and sedimentation occurred repeatedly owing to complex factors such as the discharge of the estuary and invasion by open sea waves. However, no clear unilateral trend was observed. Unlike previous survey data, a large amount of erosion occurred in the second half of 2020. Previously, sedimentation was the main process, but erosion occurred rapidly, which was observed in the summer of 2020 when the erosion was three times higher than that in other periods owing to the severe rainy season and torrential rains for over a month. In addition, regarding the flow rate and force of the river water outflow, the amount of discharge increased rapidly, causing erosion. Moreover, a strong typhoon in the summer of 2020 affected the topography of the estuary.

Osteoporosis is a common metabolic bone disease in patients with diabetes, which can develop simultane-ously with Type 2 diabetes (T2D) in postmenopausal women. Bisphosphonate (BP) is administered to pa-tients with both the conditions and may cause medication-related osteonecrosis of the jaws (MRONJ). It affects the differentiation and function of osteoclasts as well as thickness of cortical bone through bone mineralization. Therefore, this study aimed to investigate the effects of T2D on osteoclast differentiation and activity as well as cortical bone formation in postmenopausal patients with MRONJ. Tissue samples were collected from 10 patients diagnosed with T2D and Stage III MRONJ in the experimental group and from 10 patients without T2D in the control group. Histological examination was conducted, and expres-sion of dendritic cell-specific transmembrane protein (DC-STAMP) and tartrate resistant acid phosphatase (TRAP) was assessed. Cortical bone formation was analyzed using CBCT images. The number of TRAP-positive osteoclasts and DC-STAMP-positive mononuclear cells were significantly less in the experi-mental group (p < 0.05). Furthermore, the thickness and ratio of cortical bone were significantly greater in the experimental group (p < 0.05). In conclusion, T2D decreased the differentiation and function of osteo-clasts, and increased cortical bone formation in postmenopausal patients with MRONJ.

U-Net, based on a deep convolutional neural network (CNN), has been clinically used to au-to-segment normal organs and potentially target volumes. However, CNNs with local geometric dependencies may limit the accuracy of segmentation. Additionally, the performance of CNNs can vary depending on the selection of network hyper-parameters, which was mitigated by the proposition of nnU-Net. We chose a vision transformer architecture called VT U-Net, which features a self-attention excluding the convolution layer, to overcome the limitations of CNNs by utilizing global geometric information of images. The VT U-Net v.2 became more powerful thanks to the adaptive hyper-parameter optimizer embedded in nnU-Net. However, despite leveraging the benefits of nnU-Net, VT U-Net v.2 still had additional network hyper-parameters that needed to be optimally chosen. Accordingly, among various hyper-parameters, this study attempted to find the optimal combination of the patch size and the embedded dimension regarding the transformer. From the 4-fold cross-validation, the modified VT U-Net v.2 showed the highest average performance for planning target volume (PTV) segmentation among the investigated networks. Though nnU-Net was based on convolution layers, the adaptive hyper-parameter optimizers turned out to enhance the performance. It was also confirmed that network hyper-parameters affected the segmentation accuracy of vision transformers.

Quadrotor drones have rapidly gained interest recently. Numerous studies are underway for the commercial use of autonomous drones, and especially the distribution businesses are taking serious reviews on drone delivery services. However, there are still many concerns about urban drone operations. The risk of failures and accidents makes it difficult to provide drone-based services in the real world with ease. There have been many studies that introduced supplementary methods to handle drone failures and emergencies. However, we discovered the limitation of the existing methods. The majority of approaches were improving PID-based control algorithms which is the dominant drone control method. This type of low-level approach lacks situation awareness and the ability to handle unexpected situations. This study introduces an event-based control methodology that takes a high-level diagnosing approach that can implement situation awareness via time-window. While leaving the low-level controller to involve in operating the drone for most of the time in normal situations, our controller operates at a higher level and detects unexpected behaviors and abnormal situations of the drone. We tested our method with real-time 3D computer simulation environments with Unreal Engine[15] and AirSim[31]. We were able to verify that our approach can provide enhanced double safety and better ensure safe drone operations. We hope our discovery to possibly contribute to the advance of real-world drone services in the near future.

Background and Objective: There is a paucity of literature comparing unilateral instrumented transforaminal lumbar interbody fusion (UITLIF) with bilateral instrumented TLIF (BITLIF) regarding radiological alignment, including the coronal balance, even though UITLIF might have asymmetric characteristics in the coronal plane. This retrospective study aimed to compare the clinical and long-term radiological outcomes of 1-level UITLIF and BITLIF in lumbar degenerative diseases (LDD). Materials and Methods: Patients who underwent 1-level UITLIF with two rectangular polyetheretherketone (PEEK) cages or BITLIF with ≥ 5 years of follow-up at a single hospital were included. We compared the clinical and radiological outcomes between the UITLIF and BITLIF. Results: In total, 63 and 111 patients who underwent UITLIF and BITLIF, respectively, were enrolled. The median follow-up was 85.55 months (range: 60–130). The UITLIF group had a significantly shorter operation time (185.0 [170.0–210.0] vs. 225.0 [200.0–265.0], p &lt; 0.001) and lower estimated blood loss (300.0 [250.0–500.0] vs. 550.0 [400.0–800.0], p &lt; 0.001) than BITLIF group. Regarding the clinical outcomes, there were no significant differences in the intermittent claudication score (p = 0.495) and Kirkaldy–Willis criteria (p = 0.707) at 1 year postoperatively. The interval changes of the local coronal Cobb angle at the index level, L1-S1 lordotic angle, and coronal off-balance from the immediate postoperative radiograph to the last follow-up were not significantly different (p = 0.687, p = 0.701, and p = 0.367, respectively). Conclusion: UITLIF with two rectangular PEEK cages is a viable option for providing comparable clinical outcomes and radiological longevity to BITLIF in 1-level LDD. In addition, UITLIF has advantages over BITLIF in terms of operative time and blood loss.

This study determines the threshold for the computational rate of actuator motor controllers for unmanned underwater vehicles necessary to accurately follow discontinuous square wave commands. Motors must track challenging square-wave inputs, and identification of key computational rates permit application of deterministic artificial intelligence (D.A.I.) to achieve tracking to a machine-precision degree of accuracy in direct comparison to other state-of-art approaches. All modeling approaches are validated in MATLAB simulations where the motor process is discretized at varying step-sizes (inversely proportional to computational rate). At a large step-size (fast computational rate), discrete D.A.I. shows a mean error more than three times larger than that of a ubiquitous model-following approach. Yet, at a smaller step size (slower computational rate), the mean error decreases by a factor of 10, only three percent larger than that of continuous D.A.I. Hence, the performance of discrete D.A.I. is critically affected by the sampling period for discretization of the system equations and computational rate. Discrete D.A.I. should be avoided when small step-size discretization is unavailable. In fact, continuous D.A.I. has surpassed all modeling approaches which makes it the safest and most viable solution to future commercial applications in unmanned underwater vehicles.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

Emotion plays a powerful role in humans’ interaction with robots. In order to express more human-friendly emotions, robots need the capability of contextual appraisal that expresses the emotional relevance of various targets in the spatiotemporal situation. In this paper, an emotional appraisal methodology is proposed in this study to cope with such contexts. Specifically, the Ortony, Clore, and Collins model is abstracted and simplified to approximate an emotional appraisal model in the form of a sentence-based cognitive system. The contextual emotion appraisal is modeled by formulating the emotional relationships among multiple targets and the emotional transition with events and time passing. To verify the proposed robotic system’s feasibility, simulations were conducted for scenarios where it emotional interacts with humans manipulating liked or disliked objects on a table. This experiment demonstrated that the robot's emotion can variously change over time like human by using a proposed formula for emotional valence, which is moderated by emotion appraisal of occurring events.

Activities in the digital economy driven by information technology have rapidly increased in scope and speed in the aftermath of COVID-19. Meanwhile, social isolation accelerated by quarantine measures has increased concerns about individuals’ mental health. However, little is known about the specific consequences of online interactions, especially when applied in online fan community-based relationships where loyal community members are prevalent. Therefore, we examined whether a sense of virtual community (SOVC) can link fans’ online activities with their mental well-being and behavioral loyalty to the platform. For this purpose, we focus on BTS fandom “Adorable Representative MC for Youth” (ARMY) behaviors and attitudes on the fan community platform Weverse. With 202 valid data samples acquired from global ARMY, this study conducted a partial least squares–structural equation modeling analysis. The empirical findings reveal that SOVC in Weverse is significantly influenced by the intensity of online interactions with other fans and parasocial relationships with celebrities. SOVC is found to be the direct predictor of fans’ behavioral loyalty and mental well-being. When considering fans’ perceptions of other social media platforms, dissatisfaction with previous online fan communities enhances the intensity of online interactions with other fans in Weverse.

(1) Background: The CEO message of hospital homepage contain various contents such as the hospital's future vision, promises with customers, upgraded services and public activities. The CEO’s message of the homepage includes non-financial information as well as financial information of corporates. Also, it provides useful information for not only company's goals and vision but also firm performance and strategies for the future. This study aims to investigate associations between CEO’s message of hospitals homepages and financial status. We used the balanced scorecard frame to analyze what content on the hospital's homepage is related to the hospital's various financial ratios. (2) Methods: We adopt a text mining method to extract significantly repeated keywords from the CEO’s message of hospital website. And we classify these keywords by a balanced scorecard frame. To examine the relationship between keywords of CEO’s message of the hospital homepage and hospital’s financial ratio, T-test is conducted for the difference in the TF-IDF (Term Frequency is Divided by Inverse Document Frequency) mean of the home page contents and its relationship with the views of the balanced scorecard framework. (3) Results: According to empirical results on 65 samples collected from local hospitals, there are some significant relationship between the qualitative content of the hospital's homepage and the quantitative financial ratio that indicates profitability, activity, leverage, liquidity, and transfer to essential business fund (EBF) income. (4) Conclusions: The introduction section of a homepage is most accessible to customers, containing the aims and ideals of hospitals and reflecting their values and visions [1]. In addition, in view of financial status, they can either emphasize financial strength or focus on other areas to mask weakness of financial information. This study reminds us of the importance of hospital website’s disclosure, and it can be inferred from the financial status of the hospital. It also highlights the need for harmonization between quantitative data, financial statements, and qualitative data, CEO’s messages. (5) Implications: To our best knowledge, this paper is the first research attempting to investigate the relation between text of hospital homepage and financial ratio of hospital through text mining technique and balanced scorecard frame. Hospitals take a crucial part in a country’s welfare and healthcare backbone industry. Nevertheless, in many countries, hospital organization sectors tend to remain a source of critical fiscal deficits due to its ineffective and sloppy management. We expect that the result of this paper can provide hospital managers to useful information.

In this study, a new empirical equation was established to predict the sedimentation volume resulting from the construction of a multipurpose weir or low-head dam. The study employed a one-dimensional numerical model (STAFF) to investigate the key parameters affecting sedimentation volume. Short-term predictions were conducted through laboratory experiments with movable bed, and the results indicated that dimensionless unit stream power and the Shields parameter exhibited the most significant correlation with dimensionless deposition volume. Using a multiple regression approach, an empirical equation was formulated and validated for predicting sedimentation in the upstream reservoir of the weir.

Gain-scheduled autopilots have emerged as a dominant strategy to achieve adaptive control of coupled, non-linear engineering complexities, owing to an ability to adapt to changing operational conditions and uncertainties. This study focuses on utilizing bilinear interpolation of gain-scheduled autopilots, emphasizing enhanced system performance and robustness. Through a comprehensive investigation and comparative analysis using three disparate cases, advantages over conventional methods are revealed. Strengths and weaknesses of both simple and specialized variants (such as linear, and real-time gain-scheduling) are introduced. Three missile guidance case–studies utilize simulation time and miss distance figures of merit. Potential to achieve precise control across various mission scenarios, while ensuring reduced computational complexity is revealed by nearly two–hundred percent improved missile miss distances with comparable distances traveled and slightly improved computational burden.

This research intended to report amine-functionalized multiwall carbon nanotubes (MWCNTs) prepared by a simple method for efficient and rapid removal of Reactive Yellow 2 (RY2) from water. EDS analysis showed that the N content increased from 0 to 2.42% and from 2.42 to 8.66% after modification by APTES and PEI, respectively. BET analysis displayed that the specific surface area, average pore size, and total pore volume were reduced from 405.22 to 176.16 m2/g, 39.67 to 6.30 nm, and 4.02 to 0.28 cm3/g, respectively. These results proved that the PEI/APTES-MWCNTs were successfully prepared. pH edge experiment indicated that pH 2 was optimal for RY2 removal. At pH 2 and 25 °C, the time required for adsorption equilibrium was 10, 15, and 180 min at initial concentrations of 50, 100, and 200 mg/L, respectively; and the maximum RY2 uptake calculated by the Langmuir model was 714.29 mg/g. Thermodynamic studies revealed that the adsorption process was spontaneous and endothermic. 0-0.1 mol/L of NaCl showed negligible effect on RY2 removal by PEI/APTES-MWCNTs. Five adsorption/desorption cycles confirmed the good reusability of PEI/APTES-MWCNTs in RY2 removal. Overall, the PEI/APTES-MWCNTs are a potential and efficient adsorbent for reactive dye wastewater treatment.

In this study, a tuned mass damper is proposed as a seismic acceleration mitigating technique of an electrical cabinet inside the nuclear power plant. In order to know the mitigation performance, the electrical cabinet and the tuned mass damper were modeled using SAP2000. The sine sweep wave was used to confirm the vibration characteristics of the cabinet over a wide frequency range, and the several various earthquakes were applied to the cabinet to verify the control performance of the tuned mass damper. After analyzing the numerical results, it is summarized that the application of the proposed technique can reduce the acceleration response of the cabinet.

TVs and monitors are among the most widely used displays in various environments. However, they have limitations in their physical display conditions, such as a fixed size/position and a rigid/flat space. In this paper, we suggest a new "Display In the Wild" (DIW) concept to overcome the aforementioned problems. Our proposed DIW system allows us to display a flexibly large screen on dynamic non-planar surfaces at an arbitrary display position. To implement our DIW concept practically, we choose a projector as the hardware configuration in order to a generate screen anywhere with different sizes. However, distortion occurs when the projector displays content on a surface that is dynamic and/or non-planar. Therefore, we propose a distortion correction method for DIW to overcome the aforementioned surface-constraints. Since projectors are not capture devices, we propose using a depth camera to determine the distortions on the surfaces quickly. We also propose DIW-specific calibration and fast/precise correction methods. Our calibration method is constructed to easily and quickly detect the projection surface, and also allows our proposed system to accommodate the intrinsic parameters such as a display resolution and field of view. We accomplish a fast undistortion process of the projector by considering only surface boundary pixels, which enables our method to run in real time. In our comprehensive experiments, the proposed DIW system generates undistorted screens such as TVs and monitors on dynamic non-planar surfaces at an arbitrary display position with Unmanned Aerial Vehicles (UAVs) in a fast and accurate manner, demonstrating its usefullness in practical DIW scenarios.

In this study, an experiment was conducted on hoop pine (Araucaria cunninghamii), which is a common tree species in Taiwan. Holes with diameters of 4, 5, 7, 10, 12, and 14 cm were drilled in dry hoop pine timber with a diameter of 39 cm and a height of 57 cm, and an 800 MHz Ground Penetrating Radar (GPR) antenna were used to determine the minimum image resolution and the size of the holes in the wood. GPR images of the timber were subjected to a filtering process to obtain characteristic reflection curves of the damage to the timber. Curves with clear waveforms were observed in the GPR profiles of eccentric holes with a diameter of 4 cm. Profiles of the damage were obtained and profile images with the trunk radius at the centre were transformed into polar coordinate images. From these polar coordinate images, the location, size and diameter of the eccentric holes in the wood were identified, and the reflection curves were characterised by waveforms and irregular fluctuations. The risk levels of tree trunks were determined on the basis of their t/R (minimum normal wall thickness of the cross-section of the trunk/radius of the trunk) values and hole area ratios. A comparison between the GPR-based results and the actual diameters of the holes revealed that the filtered GPR profiles could be used for the efficient and accurate assessment of damage to hoop pine timber (average error rate ≤ 4%).

Currently, Korea is experiencing localized extreme rainfall, which accounts for more than 80% of flood-related disasters, and is increasing in small river basins, where more than 60% of flood-related casualties occur. These events are caused by climate change and geological factors and their impact is becoming more severe. As a result, an effective measurement system is required to mitigate their impact, particularly in small stream basins that are especially vulnerable due to their steep slopes, small catchment areas, and lack of maintenance and management capacity. In addition, a Flood Early Warning Framework (FEWF) that forecasts discharge and depth during flood events is crucial for reducing casualties. Therefore, this research is focused on developing the FEWF using the nomograph and rating curve methods, which are established by the robust constrained nonlinear equation solver and are suitable for small streams. The FEWF is evaluated using real-time data observed over 7-years period from the Closed-circuit Television-based Automatic Discharge Measurement Technology (CADMT), and the results show that the FEWF is effective in forecasting discharge and depth during flood events. The use of CADMT technology for real-time data can develop an accurate and reliable FEWF, which can help mitigate the impacts of extreme rainfall events and reduce the number of flood-related casualties in small stream basins.

Individual investors often struggle to predict stock prices due to the limitations imposed by the computational capacities of personal laptop Graphics Processing Units (GPUs) when running intensive deep learning models. This study proposes solving these GPU constraints by integrating deep learning models with technical analysis methods. This integration significantly reduces analysis time and equips individual investors with the ability to identify stocks that may yield potential gains or losses in an efficient manner. Thus, a comprehensive buy and sell algorithm, compatible with average laptop GPU performance, is introduced in the study. This algorithm offers a lightweight analysis method that emphasizes factors identified by technical analysis methods, thereby providing a more accessible and efficient approach for individual investors. To evaluate the efficacy of this approach, we analyzed the performance of eight deep learning models: LSTM (4 layers), CNN, BiLSTM (4 layers), CNN Attention, BiGRU CNN BiLSTM Attention, BiLSTM Attention CNN, CNN BiLSTM Attention, and CNN Attention BiLSTM. These models were used to predict stock prices for Samsung Electronics and Celltrion Healthcare. The CNN Attention BiLSTM model displayed superior performance among these models, with the lowest validation mean absolute error value. In addition, an experiment was conducted using WandB Sweep to determine the optimal hyperparameters for four individual hybrid models. These optimal parameters were then implemented in each model to validate their back-testing rate of return. The CNN Attention BiLSTM hybrid model emerged as the highest-performing model, achieving an approximate rate of return of 5 percent. Overall, this study offers valuable insights into the performance of various deep learning and hybrid models in predicting stock prices. These findings can assist individual investors in selecting appropriate models that align with their investment strategies, thereby increasing their likelihood of success in the stock market.

This study compared condylar volume, length, and articular eminence (AE) characteristics in normal individuals and those with unilateral and bilateral juvenile idiopathic osteoarthritis (JOA). The 116 patients were divided into four groups: control (n=16), affected condyle of unilateral JOA (Aff-Uni) (n=36), non-affected condyle of JOA (NonAff-uni) (n=36), and bilateral JOA (Bi-JOA) (n=28). Volume and length differences in the condyle and AE were analyzed using ANOVA and Bonferroni post hoc tests. The results showed that Bi-JOA had significantly different condylar volume, especially in the condylar head (p&lt;0.01), specifically the middle, anterior, and medial parts (p&lt;0.05). Condylar length also differed among the groups, with differences observed between the control group and the other three groups, as well as between the bilateral group and the other three groups (p&lt;0.01). AE total volume differed between the control group and Aff-Uni. In the detailed comparison, Aff-Uni and NonAff-Uni were smaller than the control group in the posterior, lateral, and medial sections (p&lt;0.05). In conclusion, depending on the involvement of unilateral or bilateral JOA, there were differences in condylar volume and AE compared to the normal control group. Therefore, prognosis should be evaluated by distinguishing between patients with unilateral and bilateral JOA.

The purpose of this paper is to summarize and share the field experiment results of KEPCO's project consortium to create a TSO-DSO-DERA interaction scheme. The field experiment was conducted based on the prequalification algorithm proposed in the previous research from the same consortium and was designed to verify the validity of the algorithm under realistic grid conditions. In addition, during the course of the field experiment, it was found that points that were missed or not given much importance in the existing prequalification algorithm could affect the completeness of the overall system, and then practical improvements were made to improve it. The demonstration results confirm that the proposed algorithm is effective in real-world grid environments and can help DSOs ensure the reliability of the distribution system while supporting DERA's participation in the wholesale market using the proposed prequalification scheme.

In this work, alkylammonium-functionalized hollow mesoporous silica as nonocarrier of drugs was synthesized to realize enhanced cancer therapy by pH stimuli for sustained drug release. First, functionalized hollow mesoporous silica nanoparticles (Hollow MSNs) were synthesized using dodecyl dimethyl(3-sulfopropyl)ammonium hydroxide (DDAPS), sodium dodecyl sulfate (SDS), and triethanolamine as structure-directing agents, and tetraethyl orthosilicate (TEOS) and N-trimethoxysilypropyl-N,N,N-trimethylammonium chloride (TMAPS) as silica sources under basic condition via the sol-gel process. The structure and morphology of the alkylammonium-functionalized hollow mesoporous silica nanoparticles (Hollow MSN-N+CH3) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption-desorption analysis, and Fourier-transform infrared (FT-IR) spectroscopy. The functionalized hollow MSNs had a particle size of about 450 nm and a shell thickness of about 60 nm with uniform size. The nanoparticle had a surface area of 408 m2g-1, pore volume of 0.8 cm3g-1 and a uniform pore diameter of 45.9 Å. In the cancer cell viability test with MCF-7 cell, fludarabine-incorporated and alkylammonium-functionalized hollow mesoporous silica nanoparticles (Flu/Hollow MSN-N+CH3) showed excellent cancer cell death comparable with pure fludarabine drug with the controlled drug release by pH stimuli. It is considered that our current materials have the potential applicability as pH-responsive nanocarriers in the field of cancer therapy.

Marine vessels operating on the Arctic Sea route are constantly prone to collisions and friction with ice. This study discusses the wear of the hull plate caused by the collision of ice against vessels operating in Arctic Sea routes. The abrasive wear of the hull due to ice impact was numerically assessed based on both the incident behavior of ice particles interacting with the flow around the hull and the wear loss of the hull surface caused by the contact force of ice particles. A multi-phase approach was adopted to account for the behavior of ice particles continuously affected by the fluid force around the hull. The fluid force acting on the ice floe was evaluated using computational fluid dynamics (CFD) and the dynamic motion of the drift ice was evaluated using the discrete element method (DEM). The motion of the floating ice particles was updated in real time by iteratively coupling the fluid force and the motion of the ice floe at each time step of the numerical simulation. The results of the wear simulation models were presented in terms of the shape change of the hull surface due to wear. At first, the wear was evaluated for cases in which only the surface paint of the hull was damaged. Thereafter, a computation model considering the shape change of the hull surface experiencing long-term friction of ice particles was introduced. Finally, the numerical procedures to predict the abrasive wear of the hull surface by ice impact were discussed.

Current-voltage characteristics curves of NFinFET are presented and are fitted with the modi-fied current-voltage (I-V) formulas, where the modified term in the triode region is demon-strated to be indispensable. In the as-known I-V formula, important parameters need determin-ing to make both the measured data and the fitting data as close as possible. Those parameters include kN (associated with the sizes of the transistor and mobility), (associated with Early Voltage), and Vth (the threshold voltage). The differences between the measured data and the fit-ting data vary as the applied source-drain bias, proving that the mobility of the carriers is not consistently constant. On the other hand, a modified formula, called kink effect factor, is nega-tively or positively added simulating solitary heat waves, which disturb the propagation of car-riers and thus influence the Source-Drain current (IDS). The new statistical standard deviations () are then found to be effectively suppressed as the kink effect is taken into account.

We propose an algorithm for generating a panoramic image of a pipe’s inner surface based on inverse perspective mapping (IPM). For efficient crack detection, we used only perspective images of the pipe interior that can be obtained with a single lens camera instead of those taken with a 360-degree camera or a 3D depth camera. Frontal images taken while passing through the pipe were converted to images of the inner surface of the pipe using IPM. We derived a generalized IPM formula that considers the slope of the image plane to correct image distortion caused by the tilt of the plane; this IPM formula was derived based on the vanishing point of the perspective image, which was detected using optical flow techniques. Finally, the multiple transformed images with overlapping areas were combined via image stitching to create a panoramic image of the inner pipe surface. To validate our proposed algorithm, we restored images of pipe inner surface using a 3D pipe model and used these images for crack detection.

A flexible structure is applied to improve the lubrication performance of a misaligned journal bearing. The journal bearing is representative sliding bearing and there are damages due to metal-to-metal contact by misalignment. Since misalignment is an unavoidable phenomenon, a journal bearing with a flexible structure was proposed as a way to improve it. The lubrication characteristics of the bearing are evaluated numerically under steady-state condition. EHL (elastohydrodynamic lubrication) analysis considering elastic deformation was performed. The lubrication performance is compared in accordance with variation of the geometry of the flexible structure and evaluated based on the minimum film thickness. Moreover, the results of the journal bearing with flexible structure are compared with those of the journal bearing without the flexible structure. The flexible structure is then applied in the form of a groove to the area supporting high load on the journal bearing; it is elastically deformed by the generated oil-film pressure, which helps to obscure a larger oil film. Through numerical analysis, it is found that the journal bearing with flexible structure can improve the lubrication performance in the misaligned condition.

(1) Background: Due to the high proportion of disadvantaged students in a rural school in Taiwan and the gap between students’ concepts and practices of environmental protection and sustainable energy, four science and mathematics teachers in this school planned an engineering-centered PjBL of sustainable energy curriculum in a Makers Club to enhance students’ creativity, engineering skills, practices of environmental protection and sustainable energy, and learning attitudes; (2) Methods: This study is four-year action research. Teachers and students initiated the idea from rebuilding an old fan in a classroom; (3) Results: The students in the Makers Club improved their engineering skills and created various green-power generation devices (evolved from ventilation ball generator, hydropower, ocean current power generators to tiny, 3D-printing wind power generators). They turned environmental protection and sustainable energy concepts into actions during practices and won awards from science and engineering fairs every year. This creative and supportive atmosphere spread from the club to the whole school and improved the students’ practices of environmental protection and learning attitudes after long-term implementation; (4) Conclusions: The design principles of the engineering-centered PjBL of sustainable energy curriculum played a critical role and were outlined at the end of the study.

Building a new power plant to address the growing demand for power due to population concentration in the metropolitan area is one of the world's major concerns. However, since a large power plant can not be located around the city due to burden of economic cost, building power plant outside metropolitan and cities is necessary. Therefore, new power generation facilities are promoting policies to provide distributed generator(DG) with a small capacity relatively near the metropolitan. When the DG (photovoltaic, wind farm, etc.) is connected with the grid using medium voltage direct current (MVDC) system, voltage sourced converter(VSC) should supply reactive power to the grid, because of fault ride through(FRT) operation in grid fault. If the voltage drop is severe, the converter should be disconnected from the grid immediately without supplying the reactive power, resulting in a considerable economic loss. In general, superconducting fault current limiter(SFCL) is introduced as a measure to enhance FRT capability. In this paper, we use trigger type SFCL which protects superconducting element and reduces low voltage. On the other hand, the active power unbalance of the DC-link and the DC voltage rise due to the reactive power supply of the grid-side converter. The rise of the DC voltage causes the P (active power), Q (reactive power) control of the converter to deviate, causing malfunction and damage of the DC equipment. Therefore, the rise of the DC voltage must be prevented. In this paper, we consider the suppression the DC voltage rising caused by the FRT operation through the active power tracking control (APTC).

Lately, the Critical Pathway(CP) of Electronic Medical Record(EMR) is used to the guideline for a treatment in the public hospital. We propose a healthcare promotion service using disease pattern with lifestyle risk factors. We classify a medical historical patient data with disease codes with lifestyle risk factors (hypertension, diabetes, smoking, overweight, excessive alcohol intake, and low physical activity) to make the lifestyle risk factors through the classification. We finally make the clusters of disease code with lifestyle risk factors using the medical historical data based on EMR's electronic discharge summary data. As the result of that, we do a healthcare recommending service based on the disease pattern with lifestyle risk. We can build a medical help desk of a public hospital to support people as we check into the public hospital; how to get the procedure of curing, the desired curing clinical method for the healthcare promotion service by each disease code, and how to be better our healthcare. We evaluate the performance of the proposed system by experimenting with the datasets collected at the medical center to measure performance and report some experimental results.

The high demand for liquefied natural gas (LNG) requires more LNG carriers (LNGCs) to be in operation. During transportation, there is a high risk due to the required extremely low temperatures and the explosive nature of LNG cargo. Moreover, when there is a lack of experience in operating old LNGCs, there is a serious concern regarding operational accidents. A systematic maintenance strategy, especially for LNG cargo containment systems, is crucial for maintaining safe LNG transportation at sea. The purpose of this study is to develop preventive LNG cargo containment system maintenance models by using LNGC dock specifications from LNGCs of various ages. The dock specifications from a conventional LNGC repairing dock were analyzed using natural language processing techniques in order to develop preventive maintenance models of the LNG cargo containment system. From these results, and by considering the ship’s age, it was found that for young LNGCs the priority for repair should focus on checking routine consumable spare parts by tank inspections, whereas for older LNGCs the focus should be on tank condition maintenance rather than on other facilities. These results are expected to be useful in the development of a maintenance strategy of preventive LNG cargo containment systems in maritime LNG transportation.

As environmental regulations become stricter, weight- and cost-effective fiber-reinforced polymer com-posites are being considered as alternative materials in the automobile industry. Rapid impregnation of the resin into the reinforcing fibers is critical during liquid composite molding, and the optimization of resin impregnation is related to the cycle time and quality of the products. In this review, various resins capable of rapid impregnation, including thermoset and thermoplastic resins, are discussed for manu-facturing fiber-reinforced composites used in the automobile industry, along with their advantages and disadvantages. Finally, vital factors and perspectives for developing rapidly impregnated resin-based fiber-reinforced composites for automobile applications are discussed

Coastal areas are increasingly being damaged with the expansion of seawater intrusion areas. We suggest a three-step method for reducing seawater intrusion areas by predicting future damage to groundwater being used continuously. First, the area most vulnerable to seawater intrusion damage is selected from among 25 areas on the west coast of the Republic of Korea. Having identified the Taean area as the region in question in the second step, we use RCP 4.5 and 8.5 as future sea level rise scenarios and predict the future usage of groundwater using linear-regression analysis of data for the past 10 years. Consequently, for RCP 8.5 (groundwater-usage scenario 1.0), 68.5% of the total Taean area is projected to be influenced by seawater intrusion. In the third step, the effectiveness of seawater intrusion reduction measures is analyzed considering the projected future situation and the local characteristics of the Taean area. After considering the effects of alternative locations, as well as seawater intrusion related data, alternatives were prioritized using a multi-criteria decision-making method. Consequently, 3, 5, and 4 were prioritized in the listed order, and we judged that by applying seawater intrusion area reduction measures according to this result, we will achieve the biggest effect.

The biological synthesis of nanoparticles has been emerging as an environmentally benign and eco-friendly method owing to its cost-effectiveness and high efficiency. Recently, the biological synthesis of semiconductor and metal-doped semiconductor nanoparticles with enhanced photocatalytic degradation efficiency and anticancer and antibacterial properties have gained tremendous attention. In pursuit of this purpose, for the first time, we biosynthesized zinc oxide (ZnO) and silver/ZnO nanocomposites (NCs) as semiconductor and metal-doped semiconductor nanoparticles, respectively, using the cell-free filtrate (CFF) of Lysinibacillus sphaericus bacterium. The biosynthesized ZnO and Ag/ZnO were characterized by various techniques such as ultraviolet-visible spectroscopy, X-ray diffraction, Fourier-transform Infrared spectroscopy, Field-emission scanning electron microscopy, transmission electron microscopy, and photoluminescence spectroscopy. The photocatalytic degradation potential of these semiconductor/metal-semiconductor nanoparticles was evaluated against the degradation of azo dye methylene blue (MB) under simulated solar irradiation. Ag/ZnO showed 90.7 ± 0.91% photocatalytic degradation of MB, compared to 50.7 ± 0.53% by ZnO in 120 min. The cytotoxicity of ZnO and Ag/ZnO on human cervical HeLa cancer cells was determined using an MTT assay. Both nanomaterials exhibited cytotoxicity in a concentration-dependent and time-dependent manner on HeLa cells. The antibacterial activity was also determined against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus). Compared to ZnO, Ag/ZnO NPs showed higher antibacterial activity. Hence, the biosynthesis of semiconductor nanoparticles could be a promising strategy for developing hybrid metal/semiconductor nanomaterials for different biomedical and environmental applications.

Osmotic demyelination syndrome (ODS) is an acute demyelinating disorder characterized by the loss of myelin in the center of the basis pons which is defined as central pontine myelinolysis (CPM) and demyelination process in locations outside the pons which is defined as extrapontine myelinolysis (EPM). ODS including CPM and EPM is mainly caused by the rapid correction of hyponatremia. However, there are several reports of ODS in medical condition such as malnutrition, alcoholism, liver transplantation, malignancy, sepsis, electrolyte imbalance including hypernatremia, hypokalemia, hypophosphatemia, and chronic illness. Rarely, ODS was reported in patients with hyperammonemia or hyperbilirubinemia without sodium fluctuations. The symptoms usually correspond to the lesion site and EPM precedes CPM. Because ODS may be irreversible, prevention is more important. Here, we report a case of ODS secondary to the hyperammonemia and hyperbilirubinemia, as it can have unfavorable prognosis.

Gelidium jelly was traditionally made by boiling processed Gelidium seaweed and allowing the filtrate to congeal into jelly. The processing of Gelidium seaweed was very complicate involved the repeated procedures of water washing and sun drying for 7 times, and the seaweed was originally purple-red in color turned into yellow after the repeated wash and sun drying. This study aimed to evaluate the effects of halogen lamp drying methods in replace of sun drying on the physical-chemical qualities of Gelidium jellies. Properties included the agar yield, gelling temperature, hardness, springiness, rheological parameters, sensory attributes, color, and volatile compounds were investigated. The results demonstrated halogen lamp drying method required 12 times of washing and drying processes to achieve the similar jelly properties compared to sun drying for 7 times in the experimental conditions. Volatiles including heptanal, β-ionone, and (E)-2-decenal could be used as indicators to monitor the washing and drying processing. Halogen lamp was found could be an alternative processing method for seaweed drying, especially at rainy days.

Here, satellite images from 2006 to 2022 were collected to assess changes in the sandbar topography of the Nakdong River Estuary region, southeast of South Korea. The employed method of satellite image acquisition involves capturing images at the same time each year to facilitate a comparison of topographical changes over time. The shorelines of the islands in the study area, including Jinwoo Island, Shinja Island, and Doyo Sandbar, were analyzed. Shoreline analysis was performed using the digital shoreline analysis system (DSAS) package in ArcGIS. The results indicate that Jinwoo Island is expanding at 6.46 m/year in the direction of Nulcha Island. The western side of Shinja Island is expanding at 4.76 m/year, whereas the eastern side is retreating at a rate of 24.41 m/year. In the case of the Doyo Sandbar, the southern shoreline is retreating at a rate of 14.69 m/year; however, the speed is gradually decreasing. Marked topographical changes are evident in the Nakdong River Estuary, and the interlinked barrier islands undergo deposition and erosion, leading to alterations in the shoreline. These findings serve as foundational data for predicting and addressing environmental and social issues arising in the Nakdong River Estuary region due to climate change.

This paper presents a V2G strategy to flatten the daily load curve by considering the charging and discharging location of the electric vehicle to help understand the effect of the load generated by charging and discharging of the electric vehicle on the power grid. Based on the estimated share of electric vehicles, the assumption that electric vehicles go to work in the morning and leave in the afternoon was set, and the electric vehicle discharge power was calculated by reflecting both the characteristics of vehicles that go to work in the morning and the SMP1 and SMP2 plans. In addition, the electric vehicle charging power was calculated by reflecting the characteristics of vehicles returning home from work in the afternoon and the TOU rate system. In other words, in order to establish an efficient V2G strategy, a charging/discharging type-specific modeling was developed that considered all the characteristics of an electric vehicle commuting vehicle, and charging and discharging daily load using SMP1 and SMP2 rate plans for morning discharge and TOU1 and TOU2 rate plans for afternoon charging were applied. After calculating the curve, this value was compared and analyzed to evaluate the effect on grid leveling by adding the existing load. The analysis provides an accurate understanding of the impact of EV charging and discharging loads on the power grid according to V2G strategies. In this paper, it is helpful to apply EV charge and discharge management technology to avoid grid overload and minimize grid expansion by leveling the grid daily load curve by applying appropriate SMP and TOU rates through the establishment of an efficient V2G strategy by charge and discharge modeling.

In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen, depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation, and the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased, while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

White spot lesions (WSLs), a side effect of orthodontic treatment, can result in reversible and unaesthetic results. Graphene oxide (GO) with a bioactive glass (BAG) mixture(BAG@GO) was added to Low Viscosity Transbond XT(LV) in a ratio of 1, 3, 5%. The composite’s characterization and its physical and biological properties were verified with scanning electron microscopy(SEM) and X-ray diffraction(XRD); its microhardness, shear bond stress (SBS), cell viability, and adhesive remnant index (ARI) were also assessed. Efficiency in reducing WSL was evaluated using antibacterial activity of S. mutans. Anti-demineralization was analyzed using a cycle of the acid-base solution. Adhesives with 3 or 5 wt.% of BAG@GO showed significant increase in microhardness compared with LV. The sample and LV groups showed no significant differences in SBS or ARI. The cell viability test confirmed that none of the sample groups showed higher toxicity compared to the LV group. Antibacterial activity was higher in the 48-hour group than in the 24-hour group; the 48-hour test showed that BAG@GO had a high antibacterial effect, which was more pronounced in 5 wt.% of BAG@GO. Anti-demineralization effect was higher in the BAG@GO-group than in the LV-group; the higher the BAG@GO concentration, the higher the anti-demineralization effect.

Submucosal invasion is a critical step in gastric cancer (GC) progression, which greatly enhances metastasis risk. Cancer stem cells are responsible for invasion, metastasis, and tumor growth. To identify stem cell-related markers associated with submucosal invasion in GCs, we investigated the expression of candidate cancer stem cell (CSC) markers (CD133, CD44, and ALDH1A) and intestinal stem cell (ISC) markers (EPHB2, OLFM4, and LGR5) in early GCs with submucosal invasion. Remarkably, expression of all ISC markers and CD133 was frequently confined to the basal area of the lamina propria (basal pattern) in mucosal cancer. The proportion of stem cell marker-positive cells substantially increased during submucosal invasion. Given that ISC markers are restricted to the crypt base of the normal intestinal mucosa, these findings suggest that many early GCs may retain hierarchical characteristics. CD44 expression showed a focal pattern, ALDH1A was predominantly expressed diffusely, and there was no expansion of CD44 or ALDH1A expression in the submucosal cancer cells. RSPO2 from muscularis mucosa seem to be partly responsible for the increased expression of ISC markers in GC cells at the basal areas. We also found that ISC markers were correlated with CDX2 expression in GCs, indicating that ISC markers are involved in the intestinal differentiation in GCs. Interestingly, ISC markers (EPHB2 and OLFM4) and CD133 showed a positive impact on clinical outcomes. In particular, the prognostic value of EPHB2 was significant for intestinal-type GCs in a multivariate analysis. In summary, ISC markers and CD133 showed a basal distribution pattern along with enhanced expression in submucosal invading cells in early GCs. EPHB2 was an independent prognostic marker in intestinal-type GCs.

In order to understand the effect of Pb-CuI co-doping on the thermoelectric performance of Bi₂Te₃, n-type Bi₂Te₃ co-doped with x at% CuI and 1/2x at% Pb (x = 0, 0.01, 0.03, 0.05, 0.07, and 0.10) were prepared via high temperature solid state reaction and consolidated using spark plasma sintering. Electron and thermal transport properties, i.e., electrical conductivity, carrier concentration, Hall mobility, Seebeck coefficient, and thermal conductivity, of CuI-Pb co-doped Bi₂Te₃ were measured in the temperature range from 300 K to 523 K and compared to corresponding x% of CuI-doped Bi₂Te₃ and undoped Bi₂Te₃. The addition of a small amount of Pb significantly decreased the carrier concentration, which could be attributed to the holes from Pb atoms, thus the CuI-Pb co-doped samples show a lower electrical conductivity and a higher Seebeck coefficient compared to CuI-doped samples with similar x values. The incorporation of Pb into CuI-doped Bi₂Te₃ rarely changed the power factor because of the trade-off relationship between the electrical conductivity and the Seebeck coefficient. The total thermal conductivity(κ_tot) of co-doped samples (κ_tot ~1.4 W/m∙K at 300 K) is slightly lower than that of 1% CuI-doped Bi₂Te₃ (κ_tot~1.5 W/m∙K at 300 K) and undoped Bi₂Te₃ (κ_tot ~1.6 W/m∙K at 300 K) due to the alloy scattering. The 1% CuI-Pb co-doped Bi₂Te₃ sample shows the highest ZT value of 0.96 at 370 K. All data on electrical and thermal transport properties suggest that the thermoelectric properties of Bi₂Te₃ and its operating temperature can be controlled by co-doping.

Taekwondo has evolved from a traditional martial art into an official Olympic sport. This study introduces a novel action recognition model tailored for Taekwondo unit actions, utilizing joint motion data acquired via wearable inertial measurement unit (IMU) sensors. The utilization of IMU sensor-measured motion data facilitates the capture of the intricate and rapid movements characteristic of Taekwondo techniques. The model, underpinned by a conventional convolutional neural network (CNN)-based image classification framework, synthesizes action images to represent individual Taekwondo unit actions. These action images are generated by mapping joint motion profiles onto the RGB color space, thus encapsulating the motion dynamics of a single unit action within a solitary image. To further refine the representation of rapid movements within these images, a time-warping technique was applied, adjusting motion profiles in relation to the velocity of the action. The effectiveness of the proposed model was assessed using a dataset compiled from 40 Taekwondo experts, yielding remarkable outcomes: an accuracy of 0.998, precision of 0.983, recall of 0.982, and an F1-score of 0.982. These results underscore the time-warping technique's contribution to enhancing feature representation, as well as the proposed method's scalability and effectiveness in recognizing Taekwondo unit actions.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

The efficient generation of high-quality random numbers is essential in the operation of cryptographic modules. The quality of a random number generator is evaluated by the min-entropy of its entropy source. Typical method used to achieve high min-entropy of the output sequence is an entropy accumulation based on a hash function. This is grounded in the famous Leftover Hash Lemma which guarantees a lower bound on the min-entropy of the output sequence. However, the hash function based entropy accumulation has slow speed in general. For a practical perspective we need a new efficient entropy accumulation with the theoretical background for the min-entropy of the output sequence. In this work, we obtain the theoretical bound for the min-entropy of the output random sequence through the very efficient entropy accumulation using only bitwise XOR operations, where the input sequences from the entropy source are independent. Moreover we examine our theoretical results by applying to the quantum random number generator that uses dark noise arising from image sensor pixels as its entropy source.

Viral pathogens pose a substantial threat to public health and necessitate the development of effective remediation and antiviral strategies. This short communication aimed to investigate the antiviral efficacy of disinfectants on the surface proteins of human pathogenic viruses. Using in silico modeling, ligand binding energies (LBEs) of selected disinfectants were predicted and combined with their environmental impacts and costs through eco-pharmaco-economic analysis (EPEA). Results revealed the binding affinities of chemical disinfectants to viral proteins varied significantly (p

Abstract: NFinFET transistors with fin channel length 90nm and a planar MOSFET transistor with channel length 180nm and 90nm are presented with characteristic curves at various gate biases. A finalized algorithm with kink effects is effectively responsible for addressing the field effect transistors. The algorithm includes the modified conventional current-voltage formula and a nonlinear heat-associated kink solution which is simplified as a Gaussian form. Three parameters in modified model includes kN (related with channel width, channel length, and gate oxide capacitor, and proportional to the mobility of carriers)Vth(Threshold Voltage), and (the inverse of Early Voltage). Those parameters are determined to minimize the discrepancies between the measured data and the fitting values, but leave kinks located at around (VGS－Vth), which are deliberately eliminated by the Gaussian form because of the agitation of thermal kink effects. The whole fitting is made to be as close as the as-measured IDS-VDS. In the mean time, those determined parameters are physically meaningful after the analysis has been done.

Antimicrobial peptides (AMPs) have emerged as a promising solution to tackle bacterial infections and combat antibiotic resistance. However, their clinical application has been hindered by their vulnerability to protease degradation and toxicity towards mammalian cells. To overcome these challenges, our study aims to develop a method to enhance the stability and safety of AMPs, applicable to effective drug-device combination products. KR12 antimicrobial peptide was chosen and in order to further enhance its delivery and efficacy, HIV TAT protein-derived cell-penetrating peptide (CPP) was fused to form CPP-KR12. A new product, CPP-KR12@Si, was developed by forming silica nanoparticles with self-entrapped CPP-KR12 peptide using the biomimetic silica precipitability due to its cationic nature. Peptide delivery from CPP-KR12@Si to bacteria and cells was delivered at a slightly delayed rate with improved stability against trypsin treatment and a reduction in cytotoxicity over CPP-KR12. Finally, the antimicrobial potential of CPP-KR12@Si/bone graft substitute (BGS) combination product was demonstrated, which is coated with CPP-KR12 in the form of nanoparticles on the surface of BGS. Self-entrapped AMP in silica nanoparticles is a safe and effective AMP delivery method that will be useful for developing a drug/device combination product for tissue regeneration.

Purpose: Carotid intraplaque hemorrhage (IPH) increases risk of territorial cerebral ischemic events, but different sequences or criteria have been used to diagnose or quantify carotid IPH. The purpose of this study was to compare manual segmentation and semi-automatic segmentation for quantification of carotid IPH on magnetization-prepared rapid acquisition with gradient-echo (MPRAGE) sequences. Methods: Forty patients with 16–79% carotid stenosis and IPH on MPRAGE sequences were reviewed by two trained radiologists with more than five years of specialized experience in carotid plaque characterization with carotid plaque MRI. Initially, the radiologists manually viewed the IPH based on the MPRAGE sequence. IPH volume was then measured by three different semi-automatic methods, with high signal intensity 150%, 175%, and 200%, respectively, above that of adjacent muscle on the MPRAGE sequence. Agreement on measurements between manual segmentation and semi-automatic segmentation was assessed using the intraclass correlation coefficient (ICC). Results: There was near-perfect agreement between manual segmentation and the 150% and 175% criteria for semi-automatic segmentation in quantification of IPH volume. The ICC of each semi-automatic segmentation were as follows: 150% criteria: 0.861, 175% criteria: 0.809, 200% criteria: 0.491. The ICC value of manual vs. 150% criteria and manual vs. 175% criteria were significantly better than the manual vs. 200% criteria (p < 0.001). Conclusions: The ICC of 150% and 175% criteria for semi-automatic segmentation are more reliable for quantification of IPH volume. Semi-automatic classification tools may be beneficial in large-scale multicenter studies by reducing image analysis time and avoiding bias between human reviewers.

This paper presented a method for calculating daily load curves by considering charging and discharging locations of electric vehicles to help to understand the impact of loads generated by charging and discharging of electric vehicles on the power grid. Based on the estimated PEVs’ share, the PEVs discharge power was calculated to reflect both the characteristics of the arriving vehicle in the morning and the SMP plan after establishing a assumption that the electric vehicle arrived at work in the morning and the electric vehicle arrived at home in the afternoon for each of the charging/discharging locations, that is, work and home, of electric vehicles in the city. After calculating the daily load curve for each charging/discharging power type for the PEVs charging strategy, which takes into account both the characteristics of the vehicle arriving at home in the afternoon and the TOU fare system and the characteristics of the vehicle arriving at work in the morning and the SMP fare system, it was analyzed by comparing the impact assessment on the grid by adding the existing load. The results of this paper provide an accurate understanding of the impact of PEVs charging and discharging loads on the power grid. The results should help to establish PEVs charging and discharging load management plans to prevent overloading the power grids with appropriate SMP and TOU tariffs while curbing the reinforcement and expansion of power grids as much as possible.

In this work, polyacrylic acid-functionalized MCM-41 was synthesized, which was further interacted with calcium ions, to realize enhanced pH-responsive nanocarrier for sustained drug release. First, mesoporous silica nanoparticles (MSNs) were prepared by the sol-gel method. Afterward, (3-trimethoxysilyl)propyl methacrylate (TMSPM) modified surface was prepared by using the post-grafting method, then polymerization of acrylic acid was proceeded. After adding calcium chloride solution, polyacrylic acid-functionalized MSNs with calcium-carboxyl ionic bonds in the polymeric layer, which can prevent the cargo from leaking out of the mesopore, were prepared. The structure and morphology of the modified nanoparticles (PAA-MSNs) were characterized by X-ray diffraction (XRD), Fourier-transform infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM), and N2 adsorption-desorption analysis, etc. The controlled release of guest molecules was studied by using 5-fluorouracil (5-FU). The drug molecules-incorporated nanoparticles showed different releasing rates under different pH conditions. It is considered that our current materials have the potential as pH-responsive targeted nanocarriers in the field of medical treatment.

This study reports the recovery of Pd(II) from acid solution by a polyethylenimine (PEI) crosslinked chitin (PEI-chitin) biosorbent. FE-SEM analysis demonstrated that there are many slot-like pores on PEI-chitin. N2 adsorption-desorption experiment revealed that the average pore size was 47.12 nm. Elemental analysis verified the successful crosslinking of PEI with raw chitin. The Langmuir model better explained the isotherm experimental data and the theoretical maximum Pd(II) uptake was 59.6 mg/g. The adsorption kinetic data was better described by pseudo-second-order model and the adsorption equilibrium was achieved within 30 min for all initial Pd(II) concentrations of 50-200 mg/L. In the fixed-bed column, the adsorption of Pd(II) on PEI-chitin showed slow breakthrough and fast saturation performance. The desorption experiments achieved a concentration factor of 8.4 ± 0.4. In addition, adsorption-desorption cycles in the fixed-bed column were performed up to 3 times, consequently confirming the good reusability of PEI-chitin for Pd(II) recovery. Therefore, the PEI-chitin can be used as a promising biosorbent for the recovery of Pd(II) in practical applications.

This study presents a meta-analysis of studies that investigate the effectiveness of chitosan administration on lifestyle-related disease in murine models. A total of 34 published studies were used to evaluate the effect of chitosan supplementation. The effect sizes for various items after chitosan administration were evaluated using the standardized mean difference. Using Cochran’s Q test, the heterogeneity of effect sizes was assessed, after which a meta-ANOVA and –regression test was conducted to explain the heterogeneity of effect sizes using the mixed-effect model. Publication bias was performed using Egger’s linear regression test. Among the items evaluated, blood triglyceride and HDL-cholesterol showed the highest Q statistics and I2 values, respectively. Other than blood HDL-cholesterol, total cholesterol, and triglyceride in feces, most items evaluated showed a negative effect size with high significance in the fixed- and random-effect model (p<0.0001). In the meta-ANOVA and -regression test, administering chitosan and resistant starch was revealed to be most effective in lowering body weight. In addition, chitosan supplementation proved to be an effective solution for TNF-α inhibition. In conclusion, chitosan has been shown to be somewhat useful in improving symptoms of lifestyle-related disease. Although there are some limitations in the results of this meta-analysis due to the limited number of animal experiments conducted, chitosan administration nevertheless shows promise in enhancing the quality of human life.

In this paper, we define new kind of Daehee numbers, the degenerate Daehee numbers of the third kind, using degenerate log function as generating function. We obtain some identities for the degenerate Daehee numbers of the third kind associated with the Daehee, degenerate Daehee and degenerate Daehee numbers of the second kind. In addition, we derive a differential equation associated with the degenerate log function. We deduce some identities from the differential equation.

The dopamine D3 receptor is an important CNS target for the treatment of a variety of neurological diseases. Selective dopamine D3 receptor antagonists modulate the improvement of psychostimulant addiction and relapse. In this study, five and six featured pharmacophore models of D3R antagonists were generated and evaluated with the post-hoc score combining two survival scores of active and inactive. Among Top 10 models, APRRR215 and AHPRRR104 were chosen based on the coefficient of determination (APRRR215: R2training = 0.80; AHPRRR104: R2training = 0.82) and predictability (APRRR215: Q2test = 0.73, R2predictive = 0.82; AHPRRR104: Q2test = 0.86, R2predictive = 0.74) of their 3D-quantitative structure–activity relationship models. Pharmacophore-based virtual screening of a large compound library from eMolecules (> 3 million compounds) using two optimal models expedited the search process 100-fold speed increase compared to the docking-based screening (HTVS scoring function in Glide) and identified a series of hit compounds having promising novel scaffolds. After the screening, docking scores, as an adjuvant predictor, were added to two fitness scores (from the pharmacophore models) and predicted Ki (from PLSs of the QSAR models) to improve accuracy. Final selection of the most promising hit compounds were also evaluated for CNS-like properties as well as expected D3R antagonism.

We examined the relationship between living alone and the prevalence of depressive symptoms in older Korean widows and assessed the individual contributions of health, social ties, and socioeconomic factors to the development of depressive symptoms. The study was a secondary analysis using data from widows 65 years of age and older who participated in the Living Profiles of Older People Survey (LPOPS). A logistic regression analysis was used to evaluate the contributions of health, social ties, and socioeconomic factors to the development of depressive symptoms. Working status and equivalent household income were significantly associated with depressive symptoms in both those living with others and those living alone. Adjustment for health status and social ties did not change the impact of living alone on the prevalence of depressive symptoms. However, adjustment for equivalent household income eliminated the negative association between living alone and depressive symptoms. Our findings indicate that economic resources are more important than health and social ties for alleviating the negative impact of living alone on the development of depressive symptoms in older widows.

In the present study, we aimed to investigate whether an automated molecular diagnostic method based on PCR-reverse blot hybridization assay can discriminate between human Mycobacterium tuberculosis (MTB)-positive and -negative FFPE tissues and to compare the relative mRNA expression levels of various host immune markers between MTB-infected and uninfected human tissues using quantitative reverse transcription (qRT) PCR. A total of 52 human FFPE tissue samples from various regions of the body, including the lungs, lymph nodes, tendons, colon, and appendix, were collected and used for the molecular identification of Mycobacterium species and analysis of cytokine mRNA expression. As a result, IFN-γ, TNF-α, IP-10, CXCL9, CXCL11, and GM-CSF mRNA expression levels in MTB-infected tissues were significantly higher than those in uninfected samples. Additionally, the differences in the mRNA expression levels of IFN-γ, CXCL9, and GM-CSF between MTB-infected and uninfected tissues were statistically significant were statistically significant (p < 0.05). Correlation curve analysis indicated that the mRNA expression of IFN-γ was inversely proportional to that of IP-10 and that the mRNA expression levels of IFN-γ, TNF-α, CXCL9, CXCL11, GM-CSF, and TNFR were proportional and well-correlated. Furthermore, to establish marker profiles for detecting MTB infection, the statistically significant expression levels of three markers were combined. We confirmed that the combined profile of IFN-γ, CXCL9, and GM-CSF expression levels was statistically significant (P < 0.001). Although the mRNA expression patterns of host immune markers may vary according to MTB infection status, these patterns may be highly correlated and can be simultaneously used as an additional indicator for diagnosing TB.

We aimed to determine whether A-mode ultrasound (US) can provide accurate and reliable measurements comparable to those obtained through B-mode US, under diverse conditions. Thirty healthy participants (15 female, 15 male) underwent measurements of subcutaneous fat thickness (SFT), muscle thickness (MT), and muscle quality (MQ) in the trapezius and biceps brachii muscle with both US modes after and before exercises designed to stimulate the respec-tive muscles. In three key indices, the results demonstrated high validity of A-mode, with min-imal mean differences between the two devices less than 0.91mm and intraclass correlation coef-ficients exceeding 0.95 at all measures. Also, Correlation coefficients between error scores and average scores for the trapezius and biceps brachii muscles suggested no evidence of systematic error. The trapezius MT and MQ significantly increased, and biceps brachii MT significantly in-creased after exercise (p<0.05). Notably, both A-mode and B-mode exhibited the same tendency in these post-exercise changes in muscle. This study suggests that low-cost and low-resolution A-mode US provides measurements of SFT, MT, and MQ similar to more expensive, high-resolution B-mode imaging. A-mode US can serve as an affordable and portable alternative for muscle assessment.

During the recent decades, global warming by greenhouse gas evolution has attracted worldwide attention and evermore strict regulations thereon have become institutionalized as international policies. In the process, more environment-friendly power generation technologies have been developed utilizing fossil fuels with a view to timely commercialization. As one of such “clean coal” technology, Integrated Gasification Fuel Cell system is a promising power generation means and COS hydrolysis reactor is installed downstream of coal syngas to remove acidic gas constituents such as H2S and COS. The most significant design parameters affecting performance of the COS hydrolysis reactor were selected to be GHSV, (catalytic) reaction temperature, and length ratio and numerical modeling was performed considering heat and fluid flow transfer as well as chemical reaction kinetics. Effect of the selected design parameters on the variation of conversion rate and reactant gas mixture concentration were comprehensively investigated to predict performance of COS hydrolysis reactor. Stochastic modeling of reactor performance was finally performed using Monte Carlo simulation and linear regression fitting.

Codium fragile, a green algae, exhibit biological properties. In this study, we examined the effect of Codium fragile extract (CFE) on dextran sulfate sodium (DSS)-induced colitis. As the administration of CFE increased, the proliferation of Akkermansia muciniphila, which is key player in metabolic and gastrointestinal disorders, increased. After CFE administration for 10 weeks, acetic acid was revealed as the major metabolite in mouse cecum and β-glucuronidase activity in mouse feces is decreased. Further, CFE significantly alleviates the acute intestinal injury induced by DSS administration, including DAI scores and colon length. MPO activity in the colon was significantly reduced in the CFE-fed group, which indicated that CFE could inhibit neutrophils infiltration and inflammation in mice. In conclusion, a protective effect of CFE against DSS colitis suggests its clinical use for IBD patients.

This study investigated the effects of whole-body circuit training using a weighted vest on plasma resistin, cardiovascular disease risk factors, and cardiorespiratory fitness for normal-weight obese women. In this study, thirty- six normal-weight obese women were divided into three groups: Weighted Vest Circuit Training (WVCT) (n = 12), Body Weight Circuit Training (BWCT) (n = 12), and Control (CON) (n = 12). Whole-body circuit training was conducted three times a week for eight weeks to compare and analyze plasma resistin, cardiovascular disease risk factors, and cardiorespiratory fitness before and after training. Although there was no significant baseline difference between the groups regarding skeletal muscle mass, it significantly increased for the WVCT group after eight weeks. percent body fat significantly decreased for the WVCT and BWCT groups, and there was a significant difference when the percent body fat of these two groups were compared to that of the control group. Moreover, the WVCT and BWCT groups displayed a significant decrease in plasma resistin, showing a significant difference from the CON group. The WVCT and BWCT group showed a significant decrease in plasma IL-6, whereas the CON group showed a significant increase. VO2max significantly increased post-training compared to before in the BWCT group and the WVCT group, and the WVCT group showed differences between groups compared to the BWCT group and the CON group. None of the three groups displayed significant changes in plasma hs-CRP, yet there was a significant difference between the hs-CRPs of the WVCT and BWCT group and that of the CON group. In conclusion, whole-body circuit training using a weighted vest efficiently improves body composition, plasma resistin, and cardiopulmonary fitness, reducing cardiovascular disease risk factors in normal-weight obese women.

Primary spontaneous pneumothorax (PSP) is a pleural disease that abruptly affects healthy adolescents and young adults, representing a common thoracic disorder in this age group. This study aimed to investigate the necessity of preoperative chest tube insertion in patients with PSP and to re-evaluate current clinical treatment approaches. A retrospective review of medical records was conducted for children and young adults aged 14–30 years, diagnosed with PSP and who underwent Video-assisted thoracoscopic surgery (VATS) between January 2016 and December 2022 at Wonju Severance Christian Hospital. Patients were retrospectively divided into two groups based on their initial treatment: chest tube insertion and non-chest tube insertion. Clinical data including demographics, treatment details, and outcomes were collected and compared. Total 128 cases of PSP were included in the study. The total length of hospital stay was significantly shorter in the non-chest tube group (p=0.000), which was attributed to the omission of pre-operative chest tube insertions. No significant differences were observed between the two groups in terms of postoperative complications or recurrence rates. In cases of young patients with PSP, omitting pre-operative chest tube insertion may be a viable option if the patient is scheduled for VATS.

With the increase of intelligent voice phishing and the increasing reliance on open banking systems, there has been a rise in cases where individuals' personal information has been exposed, resulting in significant financial losses for the victims. Non-face-to-face transactions in the financial sector face challenges such as customer identification, ensuring transaction integrity, and preventing transaction rejection. Blockchain-based distributed ledgers have been proposed as a solution, but their adoption is limited due to the difficulty of managing private keys and the burden of gas fees management. This paper proposes a non-face-to-face P2P real-time token payment system that minimizes the risk of key loss by storing private keys in a keystore file and database through a server-based key management module. The proposed system simplifies token creation and management through a server-based token management module and implements an automatic gas charging function for smooth token transactions. Transaction integrity and non-repudiation are ensured through a transaction confirmation module that uses transaction IDs without exposing personal information. Furthermore, advanced security measures such as blocking foreign IP access and DDoS defense are implemented to securely protect user data. The proposed system aims to provide a convenient, secure, and accessible online payment solution to the public by implementing a self-authentication function using a web application that is not limited to smart phones or application platforms.

Some researchers in Taiwan argue that the current mechanism by which government subsidies are allocated for smart city demonstration projects warrants improvement. A comprehensive literature review determined that the development potential of smart cities should be prioritized in site selection for such demonstration projects. This study developed an evaluation framework on the basis of multi-criteria evaluation methods to enable the identification of suitable smart community demonstration sites. Evaluation criteria were first identified through the Delphi method. Next, the weights of each criterion were derived through the analytic hierarchy process. Furthermore, the capability of the proposed evaluation model was determined through simulation testing.

In this study, two heterogeneous fluorescence immunoassays using CdSe/ZnS quantum dot (QD) to label anti-progesterone antibody (P4Ab) for the determination of progesterone (P4) were performed in the wells of a 96-well microtiter plate. First, P4Ab was conjugated to hydrophilic CdSe/ZnS QDs via ethyl-3-(dimethylaminopropyl) carbodiimide(EDC)-N-hydroxysuccinimide) chemistry(NHS) (QDs-P4Ab conjugates). The QDs-P4Ab conjugate was employed as a second antibody in a sandwich assay, where the P4Ab was immobilized onto the 3-aminopropyltrimethoxysilane (APTMS) sol-gel membrane of the wells of a 96-well microtiter plate, and P4 was bound between the immobilized P4Ab and the QDs-P4Ab conjugate. In this assay, the fluorescence intensity of the QDs increased with increasing P4 concentrations. This assay had a detection limit of 553.9 pg/ml and a sensitivity of 18,251.96 pg/ml with a linear range of 2,184.6 – 117,082 pg/ml. In the direct binding assay, P4 was directly bound to the QDs-P4Ab conjugates immobilized onto the APTMS sol-gel membrane of the wells of a 96-well microtiter plate. In this direct binding assay the fluorescence intensity of the QDs decreased with increasing P4 concentrations, and this assay had a linear range of 28.95 – 26,607.7 pg/ml with a detection limit of 3.32 pg/ml and a sensitivity of 987.24 pg/ml. These fluorescence immunoassays have been successfully applied for the determination of P4 in real human serum, and the results were well correlated with those of a certified radioimmunoassay (RIA) method.

Recently, the intensities of natural disasters have increased significantly owing to climate change and various other environmental factors, causing unprecedented damage. Measures must be established to reduce damage from large-scale natural disasters caused by the rapidly changing environment. The Japanese government published a hazard map manual in 2015 and obligates the creation of a hazard map as a measure to reduce high-scale storm surges. This manual presents a typhoon model based on a parametric model that is used to create a hazard map. The Myers model assuming concentric circles, which is primarily used in East Asia, is disadvantageous as it cannot consider geographic characteristics. Therefore, a new parametric model is necessary to calculate wind and pressure fields, which change according to geographic characteristics. To improve this limitation of the Myers model, we calculated the wind and pressure fields considering geographical effects by combining the Holland model, which can consider the size of a developing typhoon, and the Mascon model, which changes by geographic characteristics. To determine the gradient coefficient of the Holland model, the coefficient that changes every moment was calculated using grid point value data. The result indicated excellent reproducibility of storm surge height according to the geographic characteristics.

South Korea proposed reducing greenhouse gas emissions by 37% compared to the expected emissions by 2030 as the POST-2020 greenhouse gas reduction target. Electric vehicle distribution in the public sector is essential to achieve the carbon dioxide reduction target for transportation. In particular, when buses with internal combustion engines, which travel long distances and contribute substantially to greenhouse gas emissions, are replaced with electric buses, it is expected that greenhouse gas emissions will be significantly reduced. There are three types of electric buses with different power supply systems: a plug-in type in which power is supplied when a plug is inserted, a battery-swapping type in which a battery mounted on top of the vehicle is swapped at a swapping station, and a wireless type in which the battery is wirelessly charged through self-induction at a charging facility installed on the road. Vehicles of each charging type have different advantages and disadvantages. The performance, charging type, battery capacity, and operating environment of electric buses are mutually related parameters that must be considered when introducing such vehicles. Therefore, the optimal charging type must be selected according to the operating environment to enable the widespread use of electric buses. As such, this report proposes the optimal charging type according to the operating environment of public-sector electric vehicles.

Commiphora molmol myrrh resin extracts, which have different physical properties such as polarity and dielectric constant, were prepared by immersion in extraction solvents (hot water, DMSO, hexane, ethanol, and methanol). Methanolic myrrh resin extracts showed broad antibacterial activity against isolated airborne bacteria. Furanoeudesma-1,3-diene and curzerene, as the main terpenoids in the methanolic myrrh resin extract, were analyzed using GC-MS, and the methanolic myrrh resin extracts were found to have antiviral activity (81.2% viral RNA inhibition) against H1N1 influenza virus. Biochars (wood powder-and rice husk-derived) coated with myrrh resin extracts also showed antiviral activity (22.6% and 24.3% viral RNA inhibition), due to the adsorption of terpenoids onto biochar. Myrrh resin extract using methanol as the extraction solvent is a promising agent with antibacterial and antiviral efficacy, and it can be utilized as a novel material via adsorption onto biochar for air filtration processes, cosmetics, fertilizers, drug delivery, and corrosion inhibition.

Visfatin, a member of the adipokine family, plays an important role in many metabolic and stress responses. The mechanisms underlying the direct therapeutic effects of visfatin on wound healing have not been reported yet. In this study, we examined the effects of visfatin on wound healing in vitro and in vivo. Visfatin enhanced the proliferation and migration of human dermal fibroblasts (HDFs) and keratinocytes, and significantly increased the expression of wound healing-related vascular endothelial growth factor (VEGF) in vitro and in vivo. Treatment of HDFs with visfatin induced activation of both extracellular signal-regulated kinases 1 and 2 (ERK1/2) and c-Jun N-terminal kinases 1 and 2 (JNK1/2) in a time-dependent manner. Inhibition of ERK1/2 and JNK1/2 led to a significant decrease in visfatin-induced proliferation and migration of HDFs. Importantly, blocking VEGF with its neutralizing antibodies suppressed the visfatin-induced proliferation and migration of HDFs and human keratinocytes, indicating that visfatin induces the proliferation and migration of HDFs and human keratinocytes via increased VEGF expression. Moreover, visfatin effectively improved wound repair in vivo, which was comparable to the wound healing activity of epidermal growth factor (EGF). Taken together, we demonstrate that visfatin promotes the proliferation and migration of HDFs and human keratinocytes by inducing VEGF expression and can be used as a potential novel therapeutic agent for wound healing.

This paper addresses a method to transmit streaming data via rolling shutter camera-based optical camera communications (OCC). Since the amount of data that can be contained within one frame is limited, and the continuity of received data cannot be guaranteed due to OCC environmental variations, we introduce the concept of dividing the streaming data into several fragmented sets that are transmitted sequentially. We propose a superframe to contain sequential packets of fragmented data and corresponding indexes, so that sequential packets for streaming data can be continuously collected. When redundant frame transmission is considered, any packet lost due to OCC environmental conditions can be recovered. Experimental results show that the proposed method can be successfully used to transmit streaming data, with the number of redundant frames required to acquire all data packets based on image resolution. In addition, we describe how to identify missing packets from a network point of view to reduce the number of redundant frames needed to acquire all the data. This paper presents baseline results of communication performance when sending streaming data via a rolling shutter-based OCC.

The objective of this study was to determine the effects of supplementing L-isoleucine (L-Ile) on milk protein synthesis, using an immortalized bovine mammary epithelial (MAC-T) cell line. In this case, the cells were treated with 0, 0.3, 0.6, 0.9, 1.2 and 1.5 mM of supplemental Isoleucine (Ile), and the most efficient time for protein synthesis for each amino acid was determined by measuring the cell, medium and total protein at 0, 24, 48, 72 and 96 h. Confirmatory tests showed that 48h incubation time and 0.6 mM dosage of L-Ile are considered as the optimal time and dosage. The mechanism of milk protein synthesis was elucidated through proteomics analysis to clarify the metabolic pathway. When the L-Ile was supplemented, extracellular protein (medium protein) reached a peak at 48h, whereas in the case of the intracellular cell protein, it was shown to have reached to its peak at 24h in all L-Ile dosage treatments. In total, it is noted that there were 63 upregulated and 52 downregulated proteins. The results of the protein pathway analysis showed that the L-Ile group stimulated insulin/IGF pathway-mitogen activated protein kinase kinase/MAP kinase cascade, insulin/IGF pathway-protein kinase B signaling cascade, p53 pathway, de novo purine biosynthesis, Wnt signaling pathway, glycolysis, pentose phosphate pathway, and ATP synthesis which are pathways involved and related to protein and energy metabolism. Together, these results demonstrate that L-Ile supplementation was effective in stimulating β-casein synthesis by stimulating genes and pathways which are significantly related to protein and energy metabolism.

This study aims at an acoustic design of the classical concert hall and evaluation of the acoustic performance. In terms of three acoustic parameters (i.e., reverberation time (RT), clarity (C80), and lateral fraction (LF)), this study performed acoustic simulation modeling and site measurement with the K Art Hall located in South Korea as a case study. First, in order to meet the acoustic performance of the K Art Hall (target RT: 1.4~1.7 seconds, target C80: -2dB or more +2dB or less, and target LF: 10~35%), the finish materials and shape of the room as an interior acoustic design were determined. Second, the average values of the RT, C80, and LF using the acoustic simulation modeling were estimated at 1.4 second, 1.2~1.6 dB, and 29%, respectively. Third, the average values of the RT, C80, and LF through site measuring were measured at 1.5~1.64 second, 0.07~1.31dB, and 22.22~31.37%, respectively. Thus, the results of both the acoustic simulation modeling and site measuring were analyzed so as to satisfy the target acoustic performance. The results of this study will help the decision-makers (i.e., owner, construction managers, etc.) to plan the classical concert hall in terms of the RT, C80, and LF.

A number of accidents at sea are primarily caused by low visibility due to sea fog therefore, it is important to estimate sea fog intensity and visibility in real-time in the ocean environment. However, the existing estimation systems have significant costs so that it is not viable to install them at various locations, such as small vessels, minor ports, and a number of buoys. Therefore, this paper proposes an algorithm called RDCP (Reduced Dark Channel Prior) which provides the estimation at a low complexity and a low cost. For the estimation, the RDCP algorithm firstly acquires dark channels from an ocean image, then applies an optimized threshold value to the dark channels, and crops out the sky region in the ocean image. For the estimation performance evaluation, 320 raw images captured from cameras at four different ports in South Korea are used rather than artificially composed images. Considering facilities in oceans which are usually operated in the power limited environment, the processing time performance of PDCP are also examined. The experiments demonstrate that the RDCP algorithm provides reliable estimation performance in real-time.

Emulsifiers like egg yolk (EY) are necessary for the formation of mayonnaise, which is an oil-in-water type colloid. This study aimed to assess the potential of defatted soybean powder treated with supercritical carbon dioxide (DSF-SC) in enhancing the quality of plant-based may-onnaise as plant-based alternatives gain popularity. This study involved producing DSF-SC and comparing its quality attributes to those of mayonnaise made with varying amounts of control soy flour (CSF), DSF-SC, and EY. It was found that mayonnaise made with DSF-SC, with increased emulsifier quantity, showed better emulsion stability, viscosity, and smaller, more uniform particle size compared with CSF mayonnaise. Additionally, DSF-SC mayonnaise was overall rated higher in sensory evaluation. The addition of approximately 2% DSF-SC positively influenced the emul-sion and sensory properties of the vegan mayonnaise, making DSF-SC a promising plant-based alternative emulsifier for replacing animal ingredients.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

Novel pH responsive semi-interpenetrating polymer hydrogels based on tamarind gum-co-poly(acrylamidoglycolic acid) (TMGA) polymers have been synthesized using simple free radical polymerization in the presence of bis[2-(methacryloyloxy)ethyl] phosphate as a crosslinker and potassium persulfate as a initiator. In addition, these hydrogels have been used as templates for green synthesis of silver nanoparticles (13.4±3.6 nm in diameter, TMGA-Ag) by using leaf extract of Teminalia bellirica as reducing agent. Swelling kinetics and equilibrium swelling behavior of the TMGA hydrogels have been investigated in various pH environment the maxium % equilibrium swelling behavior observed i.e., 2882±1.2. The synthesized hydrogels and silver nanocomposites have been characterized by the UV, FTIR, XRD, SEM and TEM. TMGA and TMGA-Ag hydrogels have been investigated to study the characteristics of drug delivery and antimicrobial study. Doxorubicin hydrochloride, a chemotherapeutic agent successfully encapsulated with maximum encapulstaion efficiency i.e., 69.20±1.2 and performed in vitro release studies in pH physiological and gastric environment at 37 ℃. The drug release behavior is examined with kinetic models such as zero order, first order, Higuchi, Hixson Crowell, Korsmeyer-Peppas. These release data was the best fitted with the Korsemeyer-Peppas transport mechanism with n=0.91. Treatment effect on HCT116 Cell, human colon cancer cells were assessed with cell viability and cell cycle analysis. Antimicrobial activity of TMGA-Ag hydrogels is studied against to Staphylococcus aureus and Klebsiella pneumonia. Finally, the results demonstrate that TMGA and TMGA-Ag are promising candidates for anti-cancer drug delivery and inactivation of pathogenic bacteria, respectively.

Gastric cancer is the 5th most common disease in the world and the 4th most common cause of death. It is diagnosed through esophagogastroduodenoscopy with biopsy, however there are limitations in finding lesions in the early stages. Recently, research has been actively conducted to use liquid biopsy to diagnose various cancers, including gastric cancer. Various substances derived from cancer are reflected in the blood. By analyzing these substances, it was expected that not only the presence or absence of cancer but also the type of cancer can be diagnosed. However, the amount of these substances is extremely small, and even these have various variables depending on the characteristics of the individual or the characteristics of the cancer. To overcome these, we collected methylated DNA fragments using MeDIP and compared them with normal plasma to characterize gastric cancer tissue or patient’s plasma. And we attempted to diagnose gastric cancer using the characteristics of cancer reflected in the blood through the cancer tissue and patient’s plasma. As a result, we confirmed that the consistency of common methylated fragments between tissue and plasma was approximately 41.2%, and found the possibility of diagnosing and characterizing cancer using the characteristics of the fragments through SFR and 5'end-motif analysis.

Cisplatin induces early-onset ototoxicity, resulting in hearing loss. The exact mechanism by which cisplatin causes ototoxicity remains unclear. The purpose of this study was to identify the involvement of receptor-interacting protein kinase(RIP)3-dependent necroptosis in cisplatin-induced ototoxicity in animal models. Sprague–Dawley rats (SD, 8 week) were treated via intraperitoneal (i.p) injection with cisplatin (16 mg/kg for 1 day), and their hearing thresholds were was measured by the auditory brainstem response (ABR) method. Hematoxylin and eosin (H-E) staining, immunohistochemistry, and western blots were performed to determine the effect of cisplatin-induced ototoxicity on cochlear morphology. H-E stains outlined necroptotic changes in the organ of Cortis (OCs) and spiral ganglion neurons (SGNs). Additionally, immunohistochemistry and western blot analysis showed overexpression of RIP3 in the OCs and SGNs that were treated with cisplatin. These results suggest that RIP3-dependent necroptosis was substantial in cisplatin-induced ototoxicity; inner cochlear regions, the OCs, and SGNs were especially sensitive to necroptosis.

VITEK MS PRIME (bioMerieux), a newly developed Matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF MS) system, alongside VITEK PICKME Pen (PICKME), offers easy sample preparation for bacteria and yeast. VITEK MS PRIME also offers two software platforms for filamentous fungi: the IVD database and the RUO database. Our study evaluated its identification agreement on 320 clinical isolates of bacteria and yeasts, comparing PICKME and traditional wooden toothpick sampling techniques against ASTA Mi-croIDSys Elite results. Additionally, we assessed the IVD (v3.2) and SARAMIS (v4.16) RUO data-bases on 289 filamentous fungi against molecular sequencing. The concordant rates for spe-cies-level identification of bacteria and yeasts were about 89.4% (286/320) between the PICKME and wooden toothpick, about 83.4-85.3% between VITEK MS PRIME and ASTA MicroIDSys Elite. Retesting with PICKME improved concordance to 91.9%. For filamentous fungi, species-level identification reached 71.3% with the IVD database and 85.8% with RUO, which significantly enhanced basidiomycetes' identification from 35.3% to 100%. Some strains in the IVD database, like Aspergillus vesicolor, Exophiala xenobiotica, and Nannizzia gypsea failed to be identified. VITEK MS PRIME with PICKME offers reliable and efficient microorganism identification. For fila-mentous fungi, combining the use of the RUO database can be beneficial, especially for basidi-omycetes.

In this study, to reduce the use of cement and sand, porous feldspar with excellent economic efficiency was used as a substitute in heat storage concrete layer. When cement was replaced with porous feldspar, the compressive strength was approximately 16%–63% higher compared with when cement was replaced with silicate minerals. To compensate for the reduction in strength owing to the decreased cement content, mechanical and chemical activation methods were employed. When the specific surface area of porous feldspar was increased, the unit weight was reduced by approximately 30% and the compressive strength was increased by up to 90%. When chemical activation was applied using a solidifying agent, the strength was increased by approximately 30% even though 70% of the cement content was replaced with porous feldspar. When cement and sand were replaced with porous feldspar, the compressive strength was approximately two times that of ordinary cement mortar. When the heat storage concrete layer material was replaced with porous feldspar in a pilot scale experiment, the thermal conductivity and heat storage characteristics were better than those of ordinary cement mortar, and an energy-saving effect of approximately 57% was observed, confirming the excellent applicability of porous feldspar as a building material.

Objective: The main purpose of the study is to investigate the combined effects of polydeoxyribonucleotide (PDRN) and extracorporeal shock wave therapy (ESWT) sequences on the regenerative processes in atrophied animal muscles. Methods: Thirty male New Zealand rabbits, aged 12 weeks, were divided into five groups: normal saline, PDRN, ESWT, PDRN injection before ESWT, and PDRN injection after ESWT. Following 2 weeks of cast immobilization, the respective treatments were administered to the atrophied calf muscles. Radial ESWT was performed twice weekly. The evaluation included measurements of calf circumference, tibial nerve compound muscle action potential (CMAP), and gastrocnemius (GCM) muscle thickness after 2 weeks of treatment. Histological and immunohistochemical staining, as well as Western blot analysis, were conducted 2 weeks post-treatment. Staining intensity and extent were assessed using semi-quantitative scores. Results: Groups 4 and 5 demonstrated significantly greater calf muscle circumference, GCM muscle thickness, tibial nerve CMAP, and GCM muscle fiber cross-sectional area (types I, II, and total) than in the remaining three groups (p < 0.05), while they did not did not differ significantly in these parameters. Groups 2 and 3 showed the higher values for all the observations compared to group 1 (p < 0.05). Group 4 had the greatest ratio of vascular endothelial growth factor (VEGF) to platelet endothelial cell adhesion molecule-1 (PECAM-1) in the gastrocnemius muscle fibers than in the other four groups (p < 0.05). Western blot analysis revealed significantly higher expression of angiogenesis cytokines in groups 4 and 5 than in the remaining (p < 0.05). Conclusion: The combination of ESWT and PDRN injection demonstrated superior regenerative efficacy for atrophied calf muscle tissue in rabbit models than these techniques alone or saline. Particularly, administering ESWT after PDRN injection yielded the most favorable outcomes in specific parameters.

This paper reviews the current research on the speciation and determination of mercury by various analytical instruments such as, atomic absorption spectrometer (AAS), voltammeter, inductively coupled plasma optical emission spectrometer (ICP-OES), ICP-atomic emission spectrometer (AES), ICP-mass spectrometer (MS), atomic fluorescence spectrometer (AFS), spectrophotometer, spectrofluorometer, and high performance liquid chromatography (HPLC). Approximately 126 research papers on the speciation and determination of mercury by various analytical instruments published in international journals since 2015 are reviewed. All the analytical parameters, such as limit of detection, linearity range, quality assurance and quality control studies, applicability, and interfering ions studies evaluated in the reviewed articles are tabulated. This review find outs the lack of information on speciation studies of mercury in recent years. Another important prediction from this review is authors are not much studied about the concentrations of mercury in the atmosphere.

Radiotherapy for cancer has been known to affect the responses of immune cells, especially those of CD8+ T cells that play a pivotal role in anti-tumor immunity. Clinical success of immune checkpoint inhibitors led to an increasing interest into the ability of radiation to modulate CD8+ T cell responses. Recent studies that carefully analyzed the CD8+ T cell responses following radiotherapy suggest the beneficial roles of radiotherapy on anti-tumor immunity. In addition, numerous clinical trials that evaluate the efficacy of combining radiotherapy with immune checkpoint inhibitors are undergoing. In this review, we summarize the current status of knowledge regarding the changes of CD8+ T cells following radiotherapy from various preclinical and clinical studies. Furthermore, key biologic mechanisms that underlie such modulation, including both direct and indirect effects, are described. Lastly, we discuss the current evidence and essential considerations for harnessing radiotherapy as a combination partner for immune checkpoint inhibitors.