The annual construction and demolition waste (CDW) generated from EU construction sector was 850 million tons, which represented 31% of the total waste generation and about 28% of CDW was ceramics (bricks and tiles). In this study, the feasibility of using CDW brick powder as the precursor of alkali activated mortar (AAM) and extruded polystyrene (XPS) as the lightweight aggregates to form lightweight brick powder AAM (LW-BP-AAM) for non-structural applications was investigated. The thermal conductivity of LP-BPAAM was 0.112 W/m·K with density of about 1,135 kg/m³ which was lower than the counterparts with similar density in literature. The acid resistance of LW-BP-AAM is comparable to conventional fly ash based AAM and superior than ordinary Portland cement. From the scanning electron microscopy with energy dispersive X-ray spectroscopy, there was no severe damage on the surface of LW-BP-AAM but aluminate was removed from the matrix which was further verified in Fourier transform infrared spectroscopy. The mass and strength loss of LP-BP-AAM was 1.5% and 33%, respectively. Although the compressive strength of the LP-BP-AAM was low (about 1.8 MPa), it can be improved by optimising the particle size of the XPS aggregates.

Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

The performance analysis of the internal/external flows around a high speed vehicle in near-space is fundamental and critical to the configuration and structure design for high speed aircraft. In this paper, the two-dimensional coupled implicit Reynolds Average Navier-Stokes (RANS) solver and RNG k–ε turbulence model is employed to numerically simulate the flow field of an integrated high speed vehicle. The flow field are divided three parts to solve separately and compared with that solved by integrated simulation. The flow field are decomposed to save computer storage and simulation time. The first part is inlet/isolator, the second part is combustion chamber and the third is nozzle. In the computation process, the outlet condition of isolator is endowed to the inlet boundary of combustion chamber and the outlet boundary of combustion chamber is endowed to the inlet boundary of nozzle, then the whole flow field of integrated high speed vehicle is solved. Aerodynamic characteristic of fragment-computation and integration-computation is comparatively analyzed at different angles of attack, the results show that the maximum deviation of lift coefficient obtained by fragment-computation is less than 3% compared with that by integration, the maximum deviation of drag coefficient fragment-computation is less than 5% compared with that by integration, while pitching moment coefficient deviation less than 12%. However, for simulation time-consumption, the time used by fragment-computation reduces 45% compared with integration-computation. Meanwhile, by components force analysis, it can be concluded that the aerodynamic property of inlet/isolator can been obtained separately and hardly effected by other parts.

The combination of new-generation information technology and manufacturing technology has resulted in major and profound impact on future development paradigm of manufacturing. It is challenging for existing methods to conduct a multidimensional trend exploration related to machine tool domain, which is the basis of virtually everything in manufacturing. In this paper, we proposed an integrating approach framework combined topic models, bibliometric, trend analysis and patent analysis to mine insightful information about future development from multi-source data related to machine tool, such as papers, grants, patents and news. Specifically, papers and grants provided two different perspectives to explore the current focuses and future trends in machine tool research. Furthermore, the future technology development of machine tool was investigated through patents analysis. Finally, news related to machine tool industry in recent years was analyzed to analyze future machine tool business mode. The integration of the above various analytical methods and the multi-dimensional mining of literatures enabled the analysis of the future development of machine tool domain systematically from multi-perspectives which include research, technology development and industry. The conclusions obtained in this paper is beneficial to different communities of machine tool in terms of determining the research directions for researchers, identifying industry opportunities for corporations and developing reasonable industry policy for policy makers.

Following our previous success in identifying new steroid-based anticancer agents, we herein disclosed the structural requirements for retaining high potency against cancer cells and associated modes of action. The structurally novel steroidal dimer by001 inhibited growth of different esophageal cancer cells and colony formation at low micromolar levels, elevated cellular ROS levels and caused mitochondrial dysfunction. Mechanistic studies showed that by001 induced cell death through the mitochondria and death receptor-mediated apoptotic pathways and autophagy induction, as well as inhibited migration.

Mineral prospectivity mapping (MPM), aiming to outline and prioritize mineral exploration targets, has been spurred by data-driven machine learning algorithms. Supervised data-driven MPM is a typical few-shot task, suffering from the scarcity of labeled data, over-fitting of models and uncertainty of predictions. The main objective of this contribution is to propose a robust framework of few-shot learning (FSL) combining data augmentation and transfer learning, which enables generation of prospectivity models with excellent predictive efficiency and low uncertainty. The mineral systems approach was used to transfer a conceptual mineral system into mappable exploration criteria. Synthetic minority over-sampling technique (SMOTE) was employed to augment and balance the labeled dataset, allowing for model pre-training with a large synthetic training dataset of source domain. The knowledge derived from pre-trained models was then transferred to the target domain by fine-tuning, and the prospectivity model was generated in light of over-fitting and uncertainty assessment. The proposed FSL framework was applied to tungsten prospectivity mapping in southern Jiangxi Province. The results indicate that the SMOTE-ed balanced dataset boosts the classification accuracy in the training process. The FSL models yield an arch-shaped prediction point pattern favorable for focusing potential targets with high probability and low uncertainty. The FSL models achieve a high predictive performance (test AUC=0.9172) and the lowest quantitative over-fitting value, compared to the models derived from the benchmark algorithms of random forest and support vector machine. Four levels of potential targeting zones, considering both predictive efficiency and uncertainty, are extracted from the resulting FSL prospectivity map. The final high-potential and low-risk exploration targets only cover 4.27% of the area, but capture 41.53% known tungsten deposits, achieving superior predictive performance. This study highlights the capability of FSL framework for controlling over-fitting and generating high-confidence exploration targets with low uncertainty.

Although several carbon sequestration methods have been proposed according to theories from various disciplines, it is not known which method is the best. This study evaluated and summarized the advantage and disadvantages of several major carbon sequestration methods, including carbon capture and sequestration, ocean alkalinization, algal cultivation, and wood burial, based on the first principles, namely, sequestration scale and time, elemental stoichiometry, and energy use efficiency. This study suggested that, at present, wood burial may be a leading candidate for carbon sequestration because it can be implemented immediately on a large scale, is cost-effective and efficient, has a long sequestration time, has low technical requirements, and has a relatively low impact on agriculture. This study also discussed the implementation of wood burial from the perspective of nutrient requirements. To achieve carbon neutrality by 2050, the present study proposed a 25-year project starting in 2025 with an average sequestration rate of 3 Pg C per year, which includes burying 1.5 Pg of dead wood carbon and the creation of 9.7 × 10⁶ ha woodland.

In a dual-inertia system based on permanent magnet synchronous motor (PMSM), the elastic transmission mechanism, such as reducer and coupling, is prone to mechanical resonance, which reduces the precision of servo system transmission. Model prediction and introduction of state feedback are effective methods to suppress mechanical resonance, but the control parameters de-pend on the mechanical parameters of the system. Therefore, mechanical parameter identification is very necessary. In this paper, a forgetting factor recursive least square method is used to identify the mechanical parameters of the dual-inertia elastic system. Firstly, the mathematical model of the dual-inertia system is established and reasonably simplified. Then, the discrete function of the identification algorithm is constructed, and the motor speed and electromagnetic torque are sam-pled to achieve the on-line identification of the main mechanical parameters of the dual-inertia system, and the influencing factors of the identification accuracy are analyzed. Finally, simulations and experiments are carried out to verify the effectiveness of the algorithm.

The Digital Twin is one of the big technology trends of the last decade. In the course of its rapid expansion into the various fields of application, many different definitions emerged, tailored to the respective applications. Taxonomies can cluster the diversity and define application-specific archetypes. This paper presents a characterization of the Digital Twin in the context of structural mechanics and lightweight design. It begins by exploring various definitions of the Digital Twin concept and its application in different industries. The paper further analyzes the product life cycle of structures, dividing it into the design and operational phases and identifying the requirements for a Digital Twin in each phase. The structural design process is examined, including the definition of a structure and the stages of the product development process. Additionally, the paper discusses the operational phase of structures, highlighting the need for continuous monitoring, evaluation, and adaptation through Structural Health Monitoring (SHM) systems. The paper proposes two archetypes of Digital Twins for structures: a structure-designing Digital Twin for the design phase and a structure-monitoring Digital Twin for the operational phase. The findings provide a framework for implementing Digital Twins in structural mechanics, enabling digital design and monitoring of structures for improved performance and maintenance strategies.

Adaptive bitrate (ABR) algorithms optimize the quality of streaming experiences for users in client-side video players especially in unreliable or slow mobile networks. Several rule-based heuristic algorithms can achieve stable performance, but they sometimes fail to adapt properly to changing network conditions. Fluctuating bandwidth may cause algorithms to default to behavior that creates a negative experience for the user. ABR algorithms can be generated with reinforcement learning, a decision-making paradigm in which an agent learns to make optimal choices through interactions with an environment. Training reinforcement learning algorithms for bitrate streaming requires building a simulator for an agent to experience interactions quickly; training an agent in the real environment is infeasible due to the long step times in real environments. This project explores using supervised learning to construct a world-model, or a learned simulator, from recorded interactions. A reinforcement learning agent trained inside of the learned model, rather than a simulator, can outperform rule-based heuristics. Furthermore, agents trained inside the learned world-model can outperform model-free agents in low sample regimes. This work highlights the potential for world-models to quickly learn simulators, and to be used to generate optimal policies.

The PII protein is an evolutionary highly conserved regulatory protein from bacteria to higher plants. In bacteria it modulates the activity of several enzymes, transporters and regulatory factors by interacting with them and thereby regulating important metabolic hubs like carbon/nitrogen homeostasis. More than two decades ago the PII protein was characterized for the first time in plants, but its physiological role is still not sufficiently resolved. To gain more insights into the function of this protein, we investigated the interaction behaviour of AtPII with candidate proteins by BiFC and FRET/FLIM in planta and with GFP/RFP traps in vitro. In the course of these studies we found that AtPII interacts in chloroplasts with itself as well as with known interactors like NAGK in dot-like aggregates, which we named PII foci. In these novel protein aggregates AtPII interacts also with yet unknown partners, which are known to be involved in plastidic protein degradation. Further studies revealed that the C-terminal part of AtPII is crucial for the formation of PII foci. Altogether, the presented results indicate a novel mode of interaction for PII proteins with other proteins in plants, which may be a new starting point for the elucidation of physiological functions of PII proteins in plants.

Dust storms play a crucial role in the climate system and the space environment of Mars and have a great impact on human’s Mars exploration activities. The Martian dust storms exhibit significant regional, seasonal and interannual variations due to various controlling factors such as the large-scale atmospheric circulation, varying solar radiation forcing, and Martial orbital and rotational motions and their coupling to the atmospheric dynamics. This paper focuses on the review of cur-rent understandings on Martian dust storms. This paper begins by elucidating the basic properties of dust storms, and their driving mechanisms and impacts on atmospheric dynamics, atmospheric electric property, space environment, topography, and Mars explorations. Then it introduces the observation methods on different platforms including orbiters and landers/rovers, and the da-tasets constructed based on these historical observations for Martian dust storms. Finally, we pro-posed the dust storm monitoring and forecasting for the upcoming Chinese Tianwen-3 Mars sam-pling returning mission. It concludes by depicting the future research topics to systematically un-derstand the Martian dust storms.

Seedling emergence is crucial for the establishment and growth of crops and is influenced by topsoil temperature and moisture. Mulching has been widely used to promote seedling emergence in areas with a cold spring. This study was conducted to determine and simulate the effects of transparent plastic film mulch on surface soil moisture, temperature, and seedling emergence of spring maize in Northwest China. Four treatments were used: no mulching (CK), full plastic film mulch (PMF), and partial plastic film mulch, 60 cm in width (PM60, 40 cm uncovered between rows of mulch) or 30 cm in width (PM30, 20 cm uncovered between rows of mulch). The effects of soil water conservation and temperature enhancement gradually decreased as the plastic film width decreased, but there was little difference between PMF and PM60 treatments. Soil-water-modified growing degree days (WGDD) described the beneficial effects of soil moisture and temperature with respect to seedling emergence under mulching conditions. Plastic film mulching markedly accelerated seedling emergence and increased final seedling emergence rate because mulching can shorten the autotrophy duration and maintain surface soil moisture, which leads to increased germination. The effects of seedling emergence improvement decreased as the plastic film width decreased. The relationship between WGDD and cumulative relative seedling emergence (CRE) was adequately described by a Gompertz function.

Tomato brown rugose fruit virus (ToBRFV) is an emerging tobamovirus infecting tomatoes and peppers. Due to its ability to trigger seed contamination, efficient mechanical transmission, and to break the popular resistance genes (Tm-1, Tm-2 and Tm-22), the virus has resulted in a global pandemic on greenhouse tomato production in recent years despite the implementation of strict hygiene and disinfection measures. The objective of this study was to evaluate whether ToBRFV can be transmissible through recirculating hydroponic systems and search for effective approach to contain its spread under such circumstances. We not only detected the presence of ToBRFV in the runoff water solutions collected from ToBRFV-infected tomato greenhouses, but also demonstrated the infectivity of detected virus through initiating ToBRFV infection on tomato plants using bioassay. We then conducted treatment using cold plasma-generated ozone on ToBRFV-contaminated water reservoir and further assessed the efficacy of the treatment to inac-tivate the virus. Results showed the effectiveness of the cold-plasma ozone treatment was de-pendent on the ozone concentrations (0.1 mg/L to 1.0 mg/L), the periods of exposure (24 min to 72 min), and the relative virus titers (1:100 to 1:10,000 - dilution of virus-infected tissue extract), demonstrating the cold-plasma ozone treatment could offer a promising solution to cope with the potential ToBRFV spread through a recirculating hydroponic system in a greenhouse.

Concrete cracks and local damage can affect the bond performance between concrete and steel bars, thereby reducing the durability of reinforced concrete structures. Compared with general concrete crack repair methods, biomineralization repair not only has effective bonding capabilities but is also particularly environmentally friendly. In view of this, this study aimed to apply biomineralization technology to repair damaged fiber-reinforced lightweight aggregate concrete (LWAC). Two groups of LWAC specimens were prepared. The control group used lightweight aggregates (LWAs) without bacterial spores and nutrient sources, and the experimental group used LWAs containing bacterial spores and nutrient sources. These specimens were first subjected to compression tests and pull-out tests, respectively, and thus were damaged. After the damaged specimen healed itself in different ways for 28 days, secondary compression and pull-out tests were conducted. The self-healing method of the control group involved placing the specimens in an incubator. The experimental group was further divided into experimental group I and experimental group II. The self-healing method of experimental group I was the same as that of the control group. The self-healing method of experimental group II involved soaking the specimen in a mixed solution of urea and calcium acetate for two days, and then taking it out and placing it in an incubator for two days, with a cycle of four days. The test results showed that, compared with the control group specimens, the relative bond strength ratio of the experimental group II specimens increased by 17.9%. Moreover, the EDS and XRD analysis results confirmed that the precipitate formed at the crack was calcium carbonate, which improved the compressive strength and bond strength after self-healing. This indicates that the biomineralization maintenance method used in experimental group II is more effective.

Viruses can induce the fusion of infected and neighboring cells, leading to the formation of syncytia. Cell-cell fusion is mediated by viral fusion proteins on the plasma membrane of infected cells that interact with cellular receptors on neighboring cells. Viruses use this mechanism to spread rapidly to adjacent cells or escape host immunity. For some viruses, syncytium formation is a hallmark of infection and a known pathogenicity factor. For others, the role of syncytium formation in viral dissemination and pathogenicity remains poorly understood. Human cytomegalovirus (HCMV) is an important cause of morbidity and mortality in transplant patients and the leading cause of congenital infections. Clinical HCMV isolates have broad cell tropism but differ in their ability to induce cell-cell fusions, and little is known about the molecular determinants. We developed a system to analyze HCMV glycoprotein B (gB) variants in a defined genetic background. HCMV strains TB40/E and TR were used as vectors to compare the fusogenicity of six gB variants from congenitally infected fetuses with those from three laboratory strains. Five of them conferred the ability to induce fusion of MRC-5 human embryonic lung fibroblasts to one or both backbone strains, as determined by a split GFP-luciferase reporter system. The same gB variants were not sufficient to induce syncytia in infected ARPE-19 epithelial cells, suggesting that additional factors are involved. The system described here allows a systematic comparison of the fusogenicity of viral envelope glycoproteins and may help to clarify whether fusion-promoting variants are associated with increased pathogenicity.

Plant-microbe interactions are essential for ecosystem health and agricultural productivity. Metabolomics has revolutionized our understanding of these interactions by providing powerful methods to decipher the complex chemical signals involved. This review highlights the various metabolomics techniques used to study plant-microbe interactions, such as mass spectrometry, nuclear magnetic resonance spectroscopy, and advanced imaging technologies. We also discuss the role of contemporary bioinformatics tools, extensive databases, and the increasing influence of artificial intelligence and machine learning in the analysis of metabolomics data. Integrating metabolomics with other omics fields, including transcriptomics, proteomics, and metagenomics, allows for a comprehensive understanding of the molecular mechanisms underlying plant-microbe interactions. The review emphasizes the significance of fluxomics in elucidating the dynamic nature of metabolic networks. While there are challenges in data analysis, integration, and interpretation, metabolomics has profoundly expanded our knowledge of the role metabolites play in shaping plant-microbe interactions. As metabolomics technologies advance and integrate further with other omics approaches, we anticipate groundbreaking discoveries that will provide deeper insights into these complex interactions, ultimately leading to innovative strategies for sustainable agriculture and biotechnology.

Firstly, a new set of Quasi-Cubic Trigonometric Bernstein basis with two tension shape parameters is constructed, and we prove that it is an optimal normalized totally basis in the framework of Quasi Extended Chebyshev space. And the Quasi-Cubic Trigonometric Bézier curve is generated by the basis function and the cutting algorithm of the curve are given, the shape features (cusp, inflection point, loop and convexity) of the Quasi-Cubic Trigonometric Bézier curve are analyzed by using envelope theory and topological mapping; Next we construct the non-uniform Quasi-Cubic Trigonometric B-spline basis by assuming the linear combination of the optimal normalized totally positive basis have partition of unity and continuity, and its expression is obtained. And the non-uniform B-spline basis is proved to have totally positive and high-order continuity. Finally, the non-uniform Quasi Cubic Trigonometric B-spline curve and surface are defined, the shape features of the non-uniform Quasi-Cubic Trigonometric B-spline curve are discussed, and the curve and surface are proved to be continuous.

Evaluating the economic and environmental effects of farmers' green production behaviors holds important reference value for promoting sustainable agricultural development, alleviating agricultural non-point source (NPS) pollution, and achieving the organic combination of environmental protection and economic development. This paper utilizes survey data from 1,345 farm households in the main rice production areas of Jiangxi Province, China, using the example of reduced fertilizer application (RFA) among rice farmers. By constructing a DEA—SBM model with undesirable outputs to measure environmental effects, and applying an endogenous switching model to test the economic and environmental effects of farmers' adoption of green production technologies. The study found that: (1)The behavior of RFA by farmers has a significant positive impact on their net profit per mu(NPPA), helping farmers increase their income, with the increase ranging from 2.05% to 6.54%. (2)The behavior of RFA by farmers has a significant positive impact on agricultural green productivity(AGP), contributing to the improvement of the environment, with the improvement ranging from 44.09% to 45.35%. (3)Heterogeneity analysis found inconsistencies in the income-enhancing and environmental-enhancing effects at different quantiles of NPPA and AGP. Therefore, attention should be placed on improving the agricultural product quality supervision system under the market circulation mechanism, creating land scale conditions conducive to the promotion and application of fertilizer reduction technologies, and promoting the implementation of externality internalization compensation systems.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

A overview on application of CO2 in the ironmaking and steelmaking process is presented. Study on resource utilization of CO2 is significant for the reduction of CO2 emissions and the coping with global warming. The paper introduces the research progress of CO2 utilization in the sintering, Blast Furnace, Converter, secondary refining, Continuous Casting and smelting process of stainless steel in recent years in China. According to the foreign and domestic research and application status, the paper analyzes the feasibility and metallurgical effects of the CO2 utilization in the ferrous metallurgy process. The paper mainly introduces such new techniques as 1) flue gas circulating sintering, 2) blowing CO2 through Blast Furnace tuyere and CO2 as a pulverized coal carrier gas, 3) top and bottom blowing CO2 in the converter, 4) Ladle Furnace and Electric Arc Furnace bottom blowing CO2, 5) CO2 as Continuous Casting shielding gas, 6) CO2 for stainless steel smelting, and 7) CO2 circulation combustion. CO2 has a very wide application prospect in ferrous metallurgy process and the quantity of CO2 utilization is expected to be 100kg per ton of steel. It will effectively facilitate the progress of metallurgical technology and strongly promote the energy conservation of metallurgical industry.

Considering the prevalence of cropping pattern in many Saffron cultivation regions, the continuous cropping obstacle caused the decline in growth and development. These effects justify the necessity of studying agronomic strategies to promote plant quality and production. Herein, the mono cropping, intercrop of Paulownia and Saffron, and intercrop of Soybean and Saffron patterns have been performed. The metabolites of Saffron under three cropping patterns were determined and identified using by an ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) method. Uni and multivariate statistical analysis were applied to examine the difference between groups and select the significant differential accumulated metabolites. The results showed that a total of 315 compounds were significantly changed in three comparison groups. Phenylalanine metabolism, linoleic acid metabolism, and flavonoid biosynthesis pathway has been greatly enriched by the changed metabolites. The phenyl lactate, trans-2-Hydroxy-cinnamate, γ-Linolenate, 9-oxo-octadecadienoic acid, 13-0xo-0ctadecadienoic acid, 9,12,13-TriHOME of those metabolites showed significant differential accumulation in Saffron under three cropping patterns. And the accumulation of safranal and picrocrocin related compounds, such as Crocetin, Crocin showed a similar variation regularity. These indicate that there may be a close internal relationship between the cropping pattern and the biosynthesis of metabolites related to endogenous substances and Saffron quality formation.

Greenhouse gas (GHG) emissions from human activities have climbed significantly above pre-pandemic levels and reached record highs that unequivocally accelerate global warming. Industry has a significant impact on climate change, emitting at least 21 % of global GHGs and making little overall progress toward its reduction until now. Reducing industry’s emissions requires coordinated action along the value chains in order to promote mitigation options, such as energy and material efficiency, circular material flows, and transformative changes within production processes. The authors analyzed the GHG emissions generated during the manufacturing of three different products of automotive suppliers located in Austria. Despite previous efforts toward an environmentally compatible fabrication, additional and significant reduction potentials were identified. These measures for product carbon footprint (PCF) reduction included the sourcing of low-carbon materials (which are already available on the market), more extensive use of renewable energy, and changes towards more resource efficient manufacturing processes and machinery. Depending on the materials used, the PCF can be reduced by up to 80 %. The findings serve to prepare for future PCF reporting regulations and illustrate reduction potentials to achieve future market advantages, especially when PCFs become an awarding criterion.

Heritage conservation area designation is often resisted by communities due to concerns with overly strict regulations for property alterations and negative impacts on property values. This paper addresses these concerns by examining Freemans Bay and Onehunga – two Special Character Areas (SCAs) in Auckland, New Zealand. A property value analysis was used to assess the impact of SCA designation on property values and an online questionnaire survey gathered information on homeowners’ experiences and levels of satisfaction with living in an SCA. The results indicate that designated SCA properties have higher average values than non-designated properties and homeowners are overwhelmingly satisfied with living in a SCA. The main benefits are a sense of community and having certainty around the look and feel of their neighbourhood into the future. The main issue identified by respondents is the requirement for Resource Consent. The majority of people who had gone through the process found it to be a negative experience because of the high cost in terms of time and money. A historic urban landscape approach to the development of management plans and design guidelines is recommended to improve the implementation of the Special Character Areas in Auckland and beyond.

This paper discusses a significant public-private partnership (PPP) formed by the government and Taiwanese Farmer Associations. Particularly, it will investigate a pattern of the PPP that has successfully promoted rural development and agricultural modernization in Taiwan since 1950s. Taiwanese Farmer Associations (hereafter TFAs), similar to agricultural cooperatives in South Korea and Japan, have played a policy agent in fostering rural development in this island state since 1950s. TFA’s performance inherently came from Japanese Cooperatives before World War II. The Performances of those farmer organizations are combinations of economic, social, and educational synergies. The rural development experiences in Taiwan demonstrate that success of rural modernization is carried out by a special public-private partnership (PPP). First, this paper discusses formation and development of farmer cooperative organizations in East Asian societies and compare the similarities and differences of practice of those organizations and their relations to the governments among Taiwan, South Korea, and Japan. Secondly, this paper examines collaborative mold and process in which both the government and Taiwan Farmer Associations have been extensively involved. A specific cooperative apparatus between the government and TFA functioning and operating as a perfect PPP has been formed under administrative guidance of the state. Thirdly, this paper looks at input and various supports in financial and policy perspective by the public sector. Fourthly, the paper discusses legal framework, administrative apparatus, and governance pattern for TFA. Fifthly, the paper discuses that a specific PPP successfully involving in rural modernization in Taiwan is significantly derived from the state’ guidance that properly regulates a collaboration between the government and TFA. So-call East Asian model of PPP in agricultural modernization and rural community development may become a valuable experience for most of developing countries.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

Typical modern information systems are required to process copious data. Conventional manual approaches can no longer effectively analyze such massive amounts of data, and thus humans resort to smart techniques and tools to complement human effort. Currently, network security events occur frequently, and generate abundant log and alert files. Processing such vast quantities of data particularly requires smart techniques. This study reviewed several crucial developments of existent data mining algorithms, including those that compile alerts generated by heterogeneous IDSs into scenarios and employ various HMMs to detect complex network attacks. Moreover, sequential pattern mining algorithms were examined to develop multi-step intrusion detection. These studies can focus on applying these algorithms in practical settings to effectively reduce the occurrence of false alerts. This article researched the application of data mining algorithms in network security. The academic community has recently generated numerous studies on this topic.

Wearable thermoelectric generators (w-TEGs) convert thermal energy into electrical energy to realize self-powering of intelligent electronic devices, thus reducing the burden of battery replacement and charging, and improving the usage time and efficiency of electronic devices. Through finite element simulation, this study successfully designed high-performance thermoelectric generator and made it into wearable thermoelectric module by adopting “rigid device - flexible connection” method. It was found that higher convective heat transfer coefficient on cold-end leads to larger effective temperature difference and better power generation performance of device in typical wearable scenario. Meanwhile, at same convective heat transfer coefficient on the cold-end, longer TE leg length leads to larger temperature difference established at both ends of device, larger device output power and open-circuit voltage. However, when the convective heat transfer coefficient increases to a certain level, optimization effect of increasing TE leg length on device power generation performance will gradually diminish. For devices with fixed temperature difference between two ends, longer TE leg length leads to higher resistance of TEG, resulting in lower device output power but slight increase in open-circuit voltage. Finally, sixteen 16×4×2 mm2 TEGs (L=1.38 mm, W=0.6 mm) and two modules were fabricated and tested. At hot end temperature Th=33 ℃ and cold end temperature Tc=30 ℃, the actual maximum output power Pout of TEG is about 0.2 mW, and the actual maximum output power Pout of TEG module is about 1.602 mW, which is highly consistent with the simulated value. This work brings great convenience to research and development of wearable thermoelectric modules and provides new, environmentally friendly and efficient power solution for wearable devices.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.

This article addresses the trajectory tracking between two non-identical systems with chaotic properties. We employ the Rossler chaotic and RCL-shunted Josephson junctions model in similar phase space to study trajectory tracking. In order to achieve the goal tracking, we afford two stages to approximate the target tracking. The first stage utilizes the active control technique to transfer the output signal from the RCLs-J system into the quasi-Rossler system. Then next, the RCLs-J system employs the proposed the iterative learning control scheme and the control signal from the drive system to trace the trajectory of Rossler system. The numerical results demonstrate the proposed method and the tracking system is asymptotically stable.

This research not only dedicated a less restrictive method of iteration-varying function for a learning control law to design a controller but also synchronize two nonlinear systems with free time-delay. In addition, the mathematical theory of system synchronization has proved rigorously and the theory verified through an example to demonstrate the behavior of each parameter in the theory. The design of a controller using the iterative learning control law is significant for robotic tracking. The controller in this research generates a feed-forward control input using the error dynamics among the drive-response systems. The error dynamics satisfies the Lyapunov function and the combination of output errors, which respectively represented relative estimated differences of the drive-response systems. The iterative learning control rule serves the function of a filter adding previous control error after the end of each iteration. The numerical example of a synchronous system is given a Lorenz system for driving and another with the iterative learning control law for response under different initial condition. The results verify and demonstrate the proposed mathematical theory. The simulation exhibits consistency in the behavior of each parameter to match mathematical theory.

How perceptual limits can be overcome has long been examined by psychologists. This study investigated whether visual cues, blindfolding, visual-auditory synesthetic experience and music training could facilitate a smaller frequency difference limen (FDL) in a gliding frequency discrimination test. It was hoped that the auditory limits could be overcome through visual facilitation, visual deprivation, involuntary cross-modal sensory experience or music practice. Ninety university students, with no visual or auditory impairment, were recruited for this one-between (blindfold/visual cue) and one-within (control/experimental session) designed study. A MATLAB program was prepared to test their FDL by an alternative forced-choice task (gliding upwards/gliding downwards/no change) and two questionnaires (Vividness of Mental Imagery Questionnaire & Projector-Associator Test) were used to assess their tendency to synesthesia. Participants with music training showed a significantly smaller FDL; on the other hand, being blindfolded, being provided with visual cues or having synesthetic experience before could not significantly reduce the FDL. However, the result showed a trend of reduced FDLs through blindfolding. This indicated that visual deprivation might slightly expand the limits in auditory perception. Overall, current study suggests that the inter-sensory perception can be enhanced through training but not though reallocating cognitive resources to certain modalities. Future studies are recommended to verify the effects of music practice on other perceptual limits.

Repetitive transcranial magnetic stimulation (rTMS) with intensive occupational therapy improves upper limb motor paralysis and activities of daily living after stroke; however, amount of improvement according to paralysis severity remains unverified. Target activities for daily living using patients’ upper limb functions can be established by predicting the amount of change after treatment for each severity level of upper limb motor paralysis and further aid practice planning. This study estimated post-treatment score changes for each severity level of motor paralysis (no, poor, limited, notable, and full) stratified according to Action Research Arm Test (ARAT) scores before combined rTMS and intensive occupational therapy. Severity of motor paralysis was the fixed factor for analysis of covariance, delta (post-pre) of the scores was the dependent variable. Ordinal logistic regression analysis was used to compare changes in ARAT subscores in patients, divided according to paralysis severity before treatment. A multicenter retrospective cohort dataset analyzed 907 patients with stroke hemiplegia. Largest treatment-related changes in scores were observed in the Limited recovery group for upper limb motor paralysis and Full recovery group for quality-of-life activities using paralyzed upper limb. These results will help predict treatment effects and determine exercises and goal movements for occupational therapy after rTMS.

Leading and lagging Key performance indicators (KPIs) provide a means for assurance that risk control systems, to prevent or limit major hazards. The relative importance degree of KPIs provides a theorical guidance for monitoring, inspection and maintenance of structural integrity. In this paper, structural integrity KPIs are classified into leading and lagging KPIs based on Bowtie methodology and the importance degree of the KPIs are evaluated by weight calculation on the basis of Fuzzy analytical hierarchy process (FAHP).

Background Dietary guidelines typically recommend limiting the intake of fresh red meat, yet evidence linking red meat consumption with adverse health outcomes is inconsistent. Objective To assess the level of evidence from existing systematic reviews and meta-analyses and analyze the association between high consumption of red meat and cancer risk and adverse health outcomes. Methods Eight databases were searched to collect systematic reviews and meta-analyses from database inception to December 2022. Two independent reviewers screened and extracted data and used the AMSTAR 2 tool to evaluate methodological quality of the included studies. Meta-analysis was conducted using STATA 17.0. Results A total of 18 studies were included, of which 5 were rated as high quality, 4 as medium quality, 6 as low quality, and 3 as extremely low quality. Of the 9 SRs/MAs included, primary studies with overlap were identified, and 14 studies were eventually included. The meta-analysis results showed that compared with the lowest intake of red meat, the highest intake of red meat was associated with an increased risk of colorectal cancer (OR 1.21, 95% CI 1.07-1.37), gastric cancer (OR 1.37, 95% CI 1.18-1.59), non-Hodgkin's lymphoma (OR 1.10.95% CI 1.02-1.19), stroke (RR 1.11, 95% CI 1.03-1.20), type 2 diabetes (RR 1.19 95% CI 1.04-1.37), and ischemic heart disease (RR 1.09, 95% CI 1.06-1.12), as well as a negative effect on total cholesterol (WMD 0.264, 95% CI 0.144-0.383), triglycerides (WMD -0.181, 95% CI -0.349 to -0.013), low-density lipoprotein (WMD 0.198, 95% CI 0.065-0.330), and high-density lipoprotein (WMD -0.065, 95% CI -0.109 to -0.020). However, the associations with breast cancer (RR 1.05 95% CI 1.00-1.11), glycemic control (WMD 0.040, 95% CI 0.049-0.129), and changes in body weight status [overweight (β 0.89, 95% CI 0.48-1.64); obesity (β 1.06, 95% CI 0.30-3.71)] were not significant. Conclusions This comprehensive umbrella review suggests that high consumption of red meat may increase the risk of colorectal cancer, gastric cancer, non-Hodgkin lymphoma, stroke, type 2 diabetes, and cardiovascular disease, and that reducing red meat intake is a key modifiable dietary factor for reducing risk. However, there was no significant correlation with breast cancer, kidney stones, age-related eye disease or changes in body weight.

3D reality capturing has demonstrated increased efficiency and consistently accurate outcomes in architectural digitisation. Nevertheless, despite advancements in data collecting, 3D reality capturing still lacks full automation, especially in the post-processing and modelling phase. Artificial intelligence (AI) has been a significant focus, especially in computer vision, and tasks such as image classification and object recognition might be beneficial to the digitisation process and its subsequent utilisation. This article aims to examine the potential outcomes of integrating AI technology into the field of 3D reality-capturing, with a particular focus on its use in architectural scenarios. The main methods used for data collection are laser scanning (static or mobile) and photogrammetry. As a result, image data including RGB-D data (files containing both RGB colours and Depth information) and point clouds have become the most common raw datasets available for object mapping. The study comprehensively analyses the current use of 2D and 3D deep learning techniques in documentation tasks, particularly downstream applications. It also highlights the ongoing research efforts in developing real-time applications with the ultimate objective of achieving generalisation and improved accuracy.

With the development of remote sensing satellite technology for Earth observation, remote sensing stereo images have been used for three-dimensional reconstruction in various fields, such as urban planning and construction. However, remote sensing images often include noise, occluded regions, weakly textured areas and repeated textures, which can lead to reduced accuracy in stereo matching and affect the quality of the 3D reconstruction results. To reduce the impact of complex scenes in remote sensing images on stereo matching and to ensure both speed and accuracy, we propose a new end-to-end stereo matching network based on convolutional neural networks (CNNs). The proposed stereo matching network can learn features at different scales from the original images and construct cost volumes with varying scales to obtain richer scale information. Additionally, when constructing the cost volume, we introduce negative disparity to adapt to the common occurrence of both negative and nonnegative disparities in remote sensing stereo image pairs. For cost aggregation, we employ a 3D convolution-based encoder-decoder structure that allows the network to adaptively aggregate information. Before feature aggregation, we also introduce an attention module to retain more valuable feature information, enhance feature representation, and obtain a higher-quality disparity map. By training on the publicly available US3D dataset, we obtain the accuracy that 1.115 pixel in end-point error (EPE) and 5.32% in the error pixel ratio (D1) on the test dataset, and the inference speed is 92 ms. Comparing our model with existing state-of-the-art models, we achieve higher accuracy, and the network is beneficial for the three-dimensional reconstruction of remote sensing images.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

Taiwan's bed and breakfast (B&B) development has been more than 25 years ago, from the first generation of retirement to the B&B industry, serving tourists from all over the world accom-modation, providing breakfast and accommodation mode to the present, after the change of employees from the second generation, more and more attention is paid to the cultivation and cultivation of business ability. With the advent of the era of AI technology networking, the ca-pabilities required for B&B operation are more focused on all aspects of service, and the good marketing ability of B&B can promote a green chimney-free tourism economy, which is also a favorite industry of various governments and the public. This study explores the basic vocational competency indicators required for running a B&B, with (1)EQ emotion management skills, (2)Financial management ability, (3)(SK) technical skills, and (4)Marketing and promotion management capabilities. Through the study method, the K-S Z test was determined by the con-sensus conclusion of expert reliability and validity p value

Spirit of science is one of the important components of science education theory. It not only directly affects the level of science education, but also indirectly affects the selection, education and evaluation of scientific researchers, and the development of science and technology in a country or region. Although more than a century ago, the researchers began to discuss the topic of spirit of science. However, to date, the research of the definition, attribute, structural model and its characteristics of the spirit of science has not yet made a breakthrough. Based on the detailed literature review, the related theoretical analysis and the research of the structural model of the spirit of science, this paper puts forward the new definition, the attribute and the establishment of the structural model of the spirit of science, and analyzes the match the situation from new structural model of the spirit of science and the scientific nature published by the American Society for the Advancement of Science. The results of this study are of great significance for raising the level of scientific education and cultivating future scientific researchers, enhancing their motivation and skills in innovation in scientific research and promoting the development of future scientific undertakings.

. Manufacturers are increasingly adopting mixed-flow manufacturing models to meet the growing customized, diverse, and dynamic customer demand. In such an environment, material distribution scheduling optimization is vital for smooth operations and is integral to production management. However, manufacturers frequently encounter problems like disordered and delayed material distribution. Traditional scheduling methods suffer from problems like inadequate transparency, delayed decision directives, and suboptimal results, impacting performance. To this end, this study proposes a dynamic material distribution scheduling optimization model and strategy based on digital twin (DT) to address these problems. Firstly, we introduce workstation satisfaction and establish a material distribution path optimization model minimizing total distribution cost while maximizing workstation satisfaction. Subsequently, we present a cloud-edge computing-based decision framework and explain the DT-based material distribution system's components and operation. Furthermore, a dynamic material distribution scheduling optimization mechanism based on DT is designed. By incorporating a savings method and incentive, penalty strategies, improvements are made to the path node selection probabilities and the information pheromone update rules of the traditional ant colony optimization (ACO) algorithm. Finally, a numerical case study, using real data from collaborating enterprises, validates the proposed algorithm and strategy. This research offers valuable insights into logistics management and algorithm design in smart manufacturing environments.

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals like magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For WE43 scaffolds, during the first days an increase of the smeared Young's modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the struts surfaces. In this study the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite element simulations are performed to study the influence of the substrate layer thickness and Young's modulus for single struts and for a new scaffold geometry with adapted polar f2cc,z unit cells. The finite element model is further validated by compression tests on AM scaffolds made from Zn1Mg. The results show, that even low thicknesses and Young's moduli of the substrate layer increases significantly the smeared Young's modulus under axial compression.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

Glaucoma is one of the primary causes of blindness worldwide. Canal opening surgery, a type of minimally invasive glaucoma surgery (MIGS) applied in cases of mild to moderate glaucoma, has gained increasing popularity in recent years due to its efficacy in reducing intraocular pressure, its safety profile, the simplicity of its technique, and the reduced likelihood of compromised vision. Nevertheless, the existing body of histopathological studies remains insufficient for a comprehensive understanding of post-surgical wound healing. Consequently, debates persist among researchers regarding the mechanism through which Schlemm’s canal opening surgery reduces intraocular pressure, as well as the surgical techniques that may impact the outcomes and the factors influencing surgical success. As the history of MIGS is relatively short and lacks sufficient systemic reviews or meta-analysis evaluating the influence of individual factors, this review was conducted to illuminate disparities in the researchers’ opinions at the current stage of research.

Global warming poses a threat to plant survival, impacting growth and agricultural yield. Protein turnover, a critical regulatory mechanism balancing protein synthesis and degradation, is crucial for cellular response to environmental changes. We investigated the effects of elevated temperature on proteome dynamics in Arabidopsis thaliana seedlings using 15N-stable isotope labeling and ul-tra-performance liquid chromatography-high resolution mass spectrometry, coupled with the ProteinTurnover algorithm. Analyzing different cellular fractions from plants grown under 22°C and 30°C growth conditions, we found significant changes in the turnover rates of 571 proteins, with a median 1.4-fold increase, indicating accelerated protein dynamics under thermal stress. Notably, soluble root fraction proteins exhibited smaller turnover changes, suggesting tissue-specific adap-tations. Significant turnover alterations occurred with redox signaling, stress response, protein folding, secondary metabolism, and photorespiration, indicating complex responses enhancing plant thermal resilience. Conversely, proteins involved in carbohydrate metabolism and mito-chondrial ATP synthesis showed minimal changes, highlighting their stability. This analysis high-lights the intricate balance between proteome stability and adaptability, advancing our under-standing of plant responses to heat stress and supporting the development of improved thermo-tolerant crops.

A typical vibrational spectrum in the ice phase has four separate bands: translation, libration, bending and stretching. Ice X, the final ice phase under high pressure, shows an exotic vibrational spectrum. Theoretically, an ideal crystal of ice X only has one peak at 998 cm-1 for Raman scattering and two peaks at 450 cm-1 and 1507 cm-1 for infrared absorption in this work. These three characteristic peaks are indicators of the phase transition between ice VII/VIII and ice X. Despite much experimental and theoretical work on ice X, only this study has clearly indicated these characteristic peaks in the region of the IR band. The phonon density of states shows quite different features than ice VIII, which could be verified by inelastic neutron scattering in the future. The dynamic processes of 15 vibrational normal modes are discussed and the typical hydrogen bonds are missing.

We quantitatively investigated the statistical behaviors of semiflexible polymer chains, which are simultaneously subjected to force stretching and rectangular tube confinement. Based on the wormlike chain model and Odijk deflection theory, we derived a new deflection length, by which new compact formulas are obtained for the confinement free energy and force-confinement-extension relation. These newly derived formulas have been justified by numerical solutions of an eigenvalue problem associated with the Fokker-Planck governing equation and extensive Brownian dynamics simulations based on the so-called Generalized Bead-Rod (GBR) model. We found that, comparing to the classical deflection theory, these new formulas are valid for a much extended range of the confinement-size /persistence-length ratio, and have no adjustable fitting parameters for sufficient long semiflexible chains in the whole deflection regime.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

Chinese Taihe Black-bone silky fowl (TBsf) is the homology of medicine and food and has high nutritional and medical value all over the world. However, the nutritional compositions and specific metabolite advantages of Taihe silky fowl muscle are still poorly understood. In this study, we investigated the differences of nutritional components between TBsf and another similar breed (Black Feathered chicken and laid green-shelled eggs, BF-gsc). Meanwhile, we also explored the divergences in muscle characteristics of Taihe silky fowl fed with two different diets, that is normal chicken feed (TBsf-ncf) and Broussonetia papyrifera-fermented feed (TBsf-bpf). Firstly, the growth performance and biochemical index of Taihe silky fowl was significantly different compared with black-feathered chicken. Secondly, we identified the metabolic alterations in Taihe silky fowl by performing an un-targeted UHPLC-Q-TOF-MS/MS analysis. Our results suggested that the whole metabonomic characteristics had obvious separation between TBsf-ncf, TBsf-bpf and BF-gsc groups both in the positive and negative ion mode by PCA analysis. Next, OPLS-DA multivariate analysis revealed that 57 metabolites (in positive mode) and 49 metabolites (in negative mode) were identified as differential metabolites between TBsf-ncf and BF-gsc group. These differential metabolites were mainly enriched to ABC transporters, biosynthesis of amino acids and aminoacyl-tRNA biosynthesis. Besides, there were 47 metabolites (in positive) and 13 metabolites (in negative) were differentially regulated between TBsf-ncf and TBsf-bpf group, which were majorly involved in histidine metabolism and linoleic metabolism. Furthermore, the integrated network analysis suggested that DL-arginine, DL-isoleucine, linoleoylcarnitine, stearoylcarnitine (positive) and ricionleic acid, D-proline, uric acid (negative) were the significantly metabolic biomarkers in Taihe silky fowl. Moreover, the metabolites of primaquine, ticlpoidine, riboflavin, acetylcarnitine (positive) and salicylic acid, acetaminophen sulfate, glutamic acid (negative) were markedly changed in the Taihe silky fowl fed with BP-fermented feed. In summary, a global survey of the nutritional components and metabolite differences were performed in muscle tissues of Taihe silky fowl between various breeds and feeds. The comprehensive expression profiles of the metabolites in Taihe silky fowl affected by genetic and environmental factors were acquired. This study provided valuable evidence fo breed and feed-induced putative biomarkers as well as improved the economic value of Taihe silky fowl through targeted metabolite regulation.

Disassembly is a pivotal technology to enable the circularity of electric vehicle batteries by applying circular economy strategies that extend the life cycle of their components, like remanufacturing and repurposing, or by using efficient recycling to reintegrate the gained materials in producing new battery systems. This paper aims to develop a multi-method self-configuring simulation model for investigating disassembly scenarios while considering the battery design as well as the configuration and layout of the disassembly station. We demonstrate the developed model in a case study using a battery of Mercedes-Benz and the automated disassembly station of the project DeMoBat at Fraunhofer IPA. Furthermore, we introduce two disassembly scenarios, the component-oriented and the accessibility-oriented disassembly, and compare them using the simulation model to determine several indicators, such as the frequency of tool change, the number and distribution of robot routes, the tool utilization, and the disassembly time.

Spectrally weighed irradiance on the corneal plane is often used to determine the visual and non-visual potency of light. Spectral irradiance or illuminance is measured with a diffuser in the so-called 2π geometry (i.e., a hemispheric measurement). Due to anatomical conditions, the human binocular field of view (FOV) does not correspond to a hemisphere but is occluded upwards and downwards. FOV-restricted measurements are scarce, however, and thus the error when using hemispheric measurements is yet to be determined. For our study, we designed and 3D printed FOV occlusions as attachments to spectral measurement devices. Measurements with and without the occlusion were taken in different lighting situations in the laboratory (light from different directions) and in real-world conditions (light typically from above). Our measurements show a reduction of visual and melanopic values due to the FOV occlusion ranging from negligible to over 60% for realistic scenarios. Further, the reduction was comparable for visual and melanopic parameters, as the distribution of light in the FOV was generally spectrally homogeneous. In the case of an exemplary and artificial laboratory situation, however, the melanopic daylight (D65) efficacy ratio changed by more than a factor of 2 only due to the FOV occlusion. Finally, head orientation showed a marked impact on all quantities. Our results reveal the potential for considerable error when just evaluating and comparing vertical, hemispheric measurements in experiments and non-visual lighting design projects. We thus encourage the (additional) use of a FOV occlusion for eye-level measurements in typical viewing directions and provide open-source 3D-print files.

A reinforcement learning algorithm is proposed to improve the accuracy of short-term load forecasting (STLF) in this article. The proposed model integrates radial basis function neural network (RBFNN), support vector regression (SVR), and adaptive annealing learning algorithm (AALA). In the proposed methodology, firstly, the initial structure of RBFNN is determined by using SVR. Then, an AALA with time-varying learning rates is used to optimize the initial parameters of SVR-RBFNN (AALA-SVR-RBFNN). In order to overcome the stagnation for searching optimal RBFNN, a particle swarm optimization (PSO) is applied to simultaneously find promising learning rates in AALA. Finally, the short-term load demands are predicted by using the optimal RBFNN. The performance of the proposed methodology is verified on the actual load dataset from Taiwan Power Company (TPC). Simulation results reveal that the proposed AALA-SVR-RBFNN can achieve a better load forecasting precision as compared to various RBFNNs.

Tremor is a prevalent neurological disorder characterized by involuntary shaking or trembling of body parts. This condition impairs fine motor skills and hand coordination to varying degrees and can even affect overall body mobility. As a result, tremors severely disrupt the daily lives and work of those affected, significantly limiting their physical activity space. This study developed an innovative Spatial Augmented Reality (SAR) system aimed at assisting individuals with tremor disorders to overcome their physical limitations and expand their range of activities. The system integrates eye-tracking and Internet of Things (IoT) technologies, enabling users to smoothly control objects in the real world through eye movements. It employs a virtual stabilization algorithm for stable interaction with objects in the real environment. The study comprehensively evaluated the system's performance through three experiments: 1) assessing the effectiveness of the virtual stabilization algorithm in enhancing the system's ability to assist individuals with tremors in stable and efficient interaction with remote objects; 2) evaluating the system's fluidity and stability in performing complex interactive tasks; 3) investigating the precision and efficiency of the system in remote interactions within complex physical environments. The results demonstrate that the system significantly improves the stability and efficiency of interactions between individuals with tremor and remote objects, reduces operational errors, and enhances the accuracy and communication efficiency of interactions.

In this paper, a novel voltage control strategy of stand-alone operation brushless doubly fed induction generator for variable speed constant frequency wind energy conversion systems was presented and discussed particularly. Based on the model of the generator power system, the proposed direct flux control strategy employs a nonlinear reduced-order generalized integrator based resonant sliding-mode control scheme to directly calculate and regulated the output value of converter which control winding stator required so as to eliminate the instantaneous errors of power winding stator flux, and no involving any synchronous rotating coordinate transformations. The stability, robustness and convergence capability of the proposed control strategy were described and analyzed. Owing to no extra current control loops involved, therefore simplifying the system configuration design and enhancing the transient performance. Constant converter switching frequency was achieved by using space vector pulse width modulation, which reduce the harmonic of generator terminal voltage. In addition, experimental results prove the feasibility and validity of the proposed scheme, and excellent steady and dynamic state performance is achieved.

In this paper, we tackle air quality forecasting by using machine learning approaches to predict the hourly concentration of air pollutants (e.g., Ozone, PM_2.5 and Sulfur Dioxide). Machine learning, as one of the most popular techniques, is able to efficiently train a model on big data by using large-scale optimization algorithms. Although there exists some works applying machine learning to air quality prediction, most of the prior studies are restricted to small scale data and simply train standard regression models (linear or non-linear) to predict the hourly air pollution concentration. In this work, we propose refined models to predict the hourly air pollution concentration based on meteorological data of previous days by formulating the prediction of 24 hours as a multi-task learning problem. It enables us to select a good model with different regularization techniques. We propose a useful regularization by enforcing the prediction models of consecutive hours to be close to each other, and compare with several typical regularizations for multi-task learning including standard Frobenius norm regularization, nuclear norm regularization, ℓ_2,1 norm regularization. Our experiments show the proposed formulations and regularization achieve better performance than existing standard regression models and existing regularizations.

ESG (Environmental, Social, and Governance) responsibility fulfillment increasingly affects enterprise valuation. Although researchers debate about the precise effects, the prevailing view suggests a linear relationship between ESG performance and enterprise value. This study introduces a novel ESG responsibility performance metric through the Regulated Intermediary Model to delve into this relationship within the Chinese context. Our findings reveal an inverted U-shaped relationship between ESG performance and enterprise value, with financing constraints having a significant moderating effect. These findings remain robust after employing instrumental variables to mitigate potential endogeneity. Heterogeneity analysis demonstrates that this inverted U-shaped relationship is particularly pronounced in non-polluting and non-state-owned enterprises. Moreover, a comparison between equity and debt financing mechanisms underscores that improved ESG performance is associated with lower cost of equity financing, thereby enhancing enterprise value. Financial institutions are encouraged to leverage innovative financial instruments to diversify enterprise financing channels and alleviate financing constraints of enterprises that fulfill their ESG responsibilities.

This study uses machine learning to identify key factors influencing the cost-effectiveness of over-the-counter (OTC) medications. By developing a novel cost-effectiveness rating (CER) from user ratings and prices, we analyzed data from Amazon. The findings indicate that FSA/HSA eligibility, symptom treatment range, safety warnings, special effects, active ingredients, and packaging size significantly impact cost-effectiveness across cold, allergy, digestion, and pain relief medications. Medications eligible for FSA or HSA funds, treating a broader range of symptoms, and having smaller packaging are perceived as more cost-effective. Cold medicines with safety warnings were found to be cost-effective due to their lower average price and effective ingredients like phenylephrine and acetaminophen. Allergy medications with kid-friendly features showed higher cost-effectiveness, and ingredients like calcium, famotidine, and magnesium boosted the cost-effectiveness of digestion medicines. These insights help consumers make informed purchasing decisions and assist manufacturers and retailers in enhancing product competitiveness. Overall, this research supports better decision-making in the pharmaceutical industry by highlighting factors that drive cost-effective medication purchases.

This paper studies the maximum reliability of multi-hop relay UAV, in which UAV provides wireless services for remote users without direct communication link on the ground as a coded cooperative relay. In this paper, the analytical expressions of total power loss and total bit error rate are derived as reliability measures. Firstly, based on the environmental statistical parameters, a LOS probability model is proposed. Then the problem of minimizing the bit error rate of static and mobile UAVs is studied. The goal is to minimize the total bit error rate by jointly optimizing the height, elevation, power and path loss, and subject to the maximum allowable path loss con-straints, transmission power allocation constraints and UAV height and elevation constraints. At the same time the total path loss is minimized to achieve maximum ground communication cov-erage. However, the formulated joint optimization problem is non-convex and generally difficult to solve. Therefore, we decomposed the problem into two subproblems and proposed an effective joint optimization iteration algorithm. Finally, the simulation results are given, and the analysis shows that the optimal height of different reliability measures is slightly different, and using the mobility of UAVs can improve the reliability of communication performance.

Purpose: We evaluated the outcomes of fluid-gas exchange (FGE) for long-term flap closure of idiopathic macular hole (MH) after the inverted internal limiting (ILM) flap technique. Methods: We included eyes showed flap closure without complete MH closure, connection of the apart macular tissue, 1 month postoperatively after the inverted ILM flap technique. The eyes stayed at flap closure at 2 months postoperatively further underwent in-office FGE with 16% C3F8. Results: Among 10 eyes, 5 eyes (50%) showed flap closure at 2 months postoperatively further underwent FGE for complete MH closure while the remaining 5 eyes (50%) progressed directly at 2 months postoperatively. The improvement in vision of all flap closure from baseline was significant (p=0.015), with the mean baseline vision was 1.19 [Snellen equivalent (SE), 20/307] ± 0.52 logMAR and the mean final vision being 0.63 (SE, 20/85) ± 0.38 logMAR. The group that underwent FGE showed a better final vision of 0.45 (SE, 20/75) ± 0.23 logMAR than the group that didn’t undergo FGE (0.81 [SE, 20/128] ±0.44 logMAR). All eyes achieved complete MH closure, including the eyes that underwent FGE in a mean period of 5.60 months (range 3-10 months) after the inverted ILM flap technique. The eyes that underwent FGE achieved higher rate of foveal restoration [complete external limiting membrane (ELM): 80%; complete ellipsoid zone (EZ): 60%] than those that didn’t receive FGE (complete ELM: 40%; complete EZ: 10%). Conclusions: Eyes that underwent FGE accelerated complete MH closure and showed better final vision and fovea l restoration.

Objective: To examine the effect of bilateral total lobectomy and unilateral total lobectomy on improving thyroid function in patients with thyroid micropapillary carcinoma treated with euthyrox. Methods: The study was conducted on 68 patients with thyroid micro papillary carcinoma treated with euthyroxwho had been surgically treated with euthyrox in our hospital between January 2018 and December 2019. On the basis of random number grouping, they were divided into control groups (n = 34, bilateral total lobectomy) and observation groups (n = 34, unilateral total lobectomy plus isthmectomy). Thyroid function, free triiodothyronine (FT3), thyroid hormone (TSH), and voice function (VHI score) of the two groups were compared.Results: In comparison to the control group, the observation group had shorter incision lengths, shorter operation times, and shorter hospital stays, as well as less intraoperative bleeding and drainage volume, and the difference was statistically significant (P < 0.05); As compared with the control group, the observation group had higher FT4 and FT3 levels as well as lower TSH levels, a statistically significant difference (P < 0.05).VHI scores of emotions, function, physiology, and other voice functions were significantly lower among the observation group than those of the control group (P < 0.05).Conclusion: A unilateral total lobectomy with adjacent isthmus resection in patients with thyroid micro papillary carcinoma can yield ideal results, accelerate the time taken for surgical rehabilitation, improve thyroid function, thereby improving voice quality, as well as improve the overall prognosis of the patient.

With the aging of China's population, the problem of pension security has become more and more prominent, and whether delayed retirement can effectively alleviate the pension fund gap and ensure the sustainability of the pension fund has become the focus of social concern. This study predicts the income and expenditure of urban workers' basic pension insurance fund from 2021 to 2050 by constructing an actuarial model of pension insurance fund income and expenditure, and simulates the effect of delayed retirement policy. The prediction results show that under the existing system, the basic pension insurance fund for urban workers will have a shortfall for the first time in 2027, and the shortfall will expand year by year. Compared with the non-implementation of delayed retirement policy, the simulation of the implementation of delayed retirementt program delayed the emergence of the fund gap until 2029, and the forecast period of the pension fund gap significantly narrowed, indicating that delayed retirement policy has a certain positive impact on alleviating the pressure of pension payments, but delayed retirementt can not completely eliminate the pension fund gap. In view of this, this paper suggests that a progressive and flexible delayed retirement policy should be introduced as soon as possible to better adapt to the needs of different groups. At the same time, differentiated policies should be formulated for different groups of people and a pension incentive mechanism for delayed retirement should be set up to improve public acceptance of delayed retirement policy. In addition, delayed retirement policy should be combined with other measures, such as lowering the corporate contribution rate and enhancing the value-added capacity of the pension fund, so as to ensure the sustainability of the pension fund.

Drug-target affinity (DTA) prediction is crucial for understanding molecular interactions and aiding drug discovery and development. While various computational methods have been proposed for DTA prediction, their predictive accuracy remains limited, failing to delve into the structural nuances of interactions. With increasingly accurate and accessible structure prediction of targets, we developed a novel deep learning model, named S2DTA, to accurately predict DTA by fusing sequence and structural knowledge of drugs, targets, and pockets using heterogeneous models based on graph and semantic networks. Experimental findings underscored that complex feature representations imparted negligible enhancements to the model’s performance. However, the integration of heterogeneous models demonstrably bolstered predictive accuracy. In comparison to three state-of-the-art methodologies, the supremacy of S2DTA became strikingly apparent. It showcased a noteworthy 25.2% reduction in Mean Absolute Error (MAE) and an impressive 20.1% decrease in Root Mean Square Error (RMSE). Furthermore, S2DTA exhibited substantial advancements in other pivotal metrics, including Pearson Correlation Coefficient (PCC), Spearman, Concordance Index (CI), and R2. These metrics experienced remarkable increments of at least 19.6%, 17.5%, 8.1%, and a remarkable 49.4%, respectively. Finally, we conducted interpretability analysis on the effectiveness of S2DTA by bidirectional self-attention mechanism, fully proving that S2DTA is a valuable and accurate tool for predicting DTA. For further exploration, the source data and code repository can be accessed at https://github.com/dldxzx/S2DTA.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

Starting from acid chlorides, alkynes, tryptamines, and acroyl chloride, 21 densely substituted tetrahydro-beta-carbolines are prepared in a four-component one-pot reaction. In this study, the aza-Michael addition step to generate intermediate enaminones is optimized in the presence of ytterbium triflate. Moreover, apart from acroyl chloride, all reactants can be deployed in almost equimolar ratios, which increases the atom economy of the sequence. For mechanistic rationali-zation, the concluding aza-anellation was investigated by DFT calculations on potential inter-mediates and corresponding activation energies, revealing that the aza-anellation rather pro-ceeds via ene-reaction than via electrocyclization.

The goal of this paper is to fabricate innovative diaphragm headphones using graphene oxide paper (GOP) and GOP/epoxy nanocomposites (GOPC). Initially, graphene oxide suspension is fabricated, and the vacuum filtration method is adopted to make GOP. Then vacuum bag molding is used to fabricate GOPC from GOP. Hot pressing and associated molds are adopted to fabricate line-indented (GOPC-L) or curve-indented patterns (GOPC-C) on the GOPC. The performance of one kind of GOP and three kinds of GOPC diaphragm headphones is analyzed based on their sound pressure level (SPL) curves achieved by the Soundcheck measurement system. There are four important processing parameters that will influence the performance of the diaphragm, including material type GOP versus GOPC, indented pattern type, sonication time on suspension, and graphene weight fraction in suspension. Compliances of various diaphragms are measured by the Klippel LPM laser measurement system. The results indicate that effects of sonication time and graphene weight fraction on SPL of GOP and GOPC headphones are in reverse, and this is associated with their difference on compliance (modulus), mass, damping ratio, and microstructure uniformity. Either GOPC-L or GOPC-C seems to improve the microstructure of the GOPC, and leads to better SPL performance. The correlation between the previous four factors and SPLs of four kinds of diaphragm headphones is proposed by using scanning electron microscope (SEM) to examine the microstructure of these diaphragms.

This paper aims at tackling with the task of fusion feature from images and its corresponding point clouds for 3D object detection in autonomous driving scenarios basing on AVOD, an Aggregate View Object Detection network. The proposed fusion algorithms fuse features targeted from Bird’s Eye View (BEV) LIDAR point clouds and its corresponding RGB images. Differs in existing fusion methods, which are simply the adoptions of concatenation module, element-wise sum module or element-wise mean module, our proposed fusion algorithms enhance the interaction between BEV feature maps and its corresponding images feature maps by designing a novel structure, where single level feature maps and another utilizes multilevel feature maps. Experiments show that our proposed fusion algorithm produces better results on 3D mAP and AHS with less speed loss comparing to existing fusion method used on the KITTI 3D object detection benchmark.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

Synthesis of poly(o-phenylenediamine) (PoPD) and poly(o-phenylenediamine)-ZnO (PoPD-ZnO) nanocomposites on carbon steel by in-situ polymerization with HCl acid as doping acid Material coating. The composition and structure of PoPD-ZnO nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The corrosion protection ability of polymer coatings in 3.5% NaCl was studied by potentiodynamic polarization curves and electrochemical impedance spectroscopy. It can be seen from the electrochemical corrosion experimental data that PoPD-WPU coating (PWC) and PoPD-ZnO-WPU coating (PZWC) can effectively improve the corrosion resistance of the carbon steel substrate, and the corrosion rate is reduced by 2-3 orders of magnitude compared with carbon steel. The conclusion demontrates that PoPD can effectively extend the service life of carbon steel substrates. In addition, it is advantageous to form a compact and low-defect coating when added nano-particle ZnO, which is advantageous for the POPD film to develop its good barrier property and corrosion resistance.

Bifenthrin (BF) is a new highly effective broad-spectrum insecticide that has gained widespread use. However, there is limited research on the potential toxic effects of bifenthrin pollution on amphibians. In this research, Chinese giant salamanders (CGS) were exposed to three different concentrations of BF (0, 0.04, and 4 g/L BF) for 1-week to investigate the toxic effects. Behavioral changes, liver pathology, oxidative stress factors, DNA damage, and transcriptome differences were observed and analyzed. The results showed that exposure to BF (0.04 and 4) significantly decreased the adenosine-triphosphate (ATP), superoxide dismutase (SOD), glutathione (GSH), catalase (CAT), and 8-hydroxydeoxyguanosine (8-OHdG) contents in the brain, liver, and kidney of CGS, whereas the malondialdehyde (MDA) and reactive oxygen species (ROS) contents were increased. The liver tissue showed considerable inflammatory reactions and structural malformations. RNAseq analysis of the liver showed that BF caused abnormal antioxidant indices of CGS, which affected molecular function genes such as catalytic activity, ATP-dependent activity, metabolic processes, signaling and immune system processes, behavior and detoxification significantly up-regulated, resulting the differential genes were significantly enriched in calcium signaling pathway, PPARα signaling pathway and NF-kB signaling pathway. These results indicated that BF induced the abnormal production of free radicals to exceed the potential of the self-defense system, causing different degrees of oxidative damage and lipid peroxidation in the body, resulting in oxidative stress, abnormal lipid metabolism, DNA damage, tissue inflammation, and abnormal behavior. This work provides a theoretical basis for the rational use of pyrethrin and environmental risks assessment, and scientific guidance for the conservation of amphibian populations.

Red djulis (Chenopodium formosanum) is a native cereal plant in Taiwan; it contains abundant polyphenols, betalian and dietary fiber. The appearance of red djulis is bright red. Therefore, it is also called the “ruby of cereals”. The antioxidative activity of red djulis extract is well-understood. However, the antiaging function still remains unclear. This study examined the potential of red djulis extract for enhancing collagen secretion and preventing cutaneous aging using red djulis extracts. The red djulis extracts are comprised of an abundant active component that can effectively enhance the ability of collagen secretion of dermal fibroblasts, prevent the glycation of collagen and resist the damage of ultraviolet light exposure. After fibroblast treatment with red djulis extracts, TGM1, KRT1, KRT10 and SOD2 genes were up-regulated significantly by 2.3, 4.3, 4.4 and 27.3 times, respectively, compared to those of the control group. Additionally, it can increase COL1A2 gene expression by 43% and decrease MMP9 gene expression 33%. Therefore, it was demonstrated that red djulis extracts affect gene expressions related to the skin barrier, antioxidation and collagen. Moreover, we found positive effects on skin barrier integrity, endogenous antioxidant activity and skin collagen-preservation. The preparation of the red djulis extracts is environmental friendly and can promote the economic value of Chenopodium formosanum; thus, the proposed extract is suitable for applications in the development of food products, especially beverages, skin care and cosmetic products.

Our wellbeing is greatly influenced by our childhood and adolescence, and the relationships that we form during those phases of our development. The human-dog bond started thousands of years ago. The higher prevalence of dog ownership around the world, especially in households including children along with the growing number of people studying dogs most likely explain the growing literature focusing on child-dog interactions. We review the potential effects of child-dog interactions on the physical, mental, and social wellbeing of both species. A scoping search of the SCOPUS database found several hundred documents meeting selection criteria. It allowed us to define the numerous ways in which children and dogs can interact, be it neutral (e.g., sharing a common area), positive (e.g., petting), or negative (e.g., biting). Then, we found evidence for an association between interacting with dogs during childhood and an array of health and mental benefits like stress relief and the development of empathy. Walking a dog and playing with one are perfect physical activity opportunities. Additionally, interacting with a dog can help lower stress and may have a role in the development of empathy. Nonetheless, a number of detrimental outcomes have also been identified in both humans and dogs. Children are the most at-risk population regarding dog bites and dog-borne zoonoses, which may lead to a subsequent fear of dogs or even death. Moreover, pet bereavement is generally inevitable when living with a canine companion and should not be trivialized. In terms of dogs, children sometimes take part in caretaking behaviors toward them which include going on walks. They are opportunities for dogs to relieve themselves outside, but also to exercise and socialize. In contrast, a lack of physical activity can lead to the onset of obesity. Dogs may present greater levels of stress when in the presence of children. Finally, the welfare of assistance, therapy, and free-roaming dogs remains underexplored. Overall, the study of the effects, positive as well as negative, on both species still requires further development. We call for more longitudinal studies and hope for cross-cultural research in the future in order to better understand the impact child-dog interactions might have.

The health benefits of purple sweetpotato, which is used as an edible food in its natural state and in processed foods and as a natural color pigment, have been recognized. In Japan, sweetpotato has been economically produced in regions below 36°4′N latitude, however, cultivation areas are beginning to expand further north. The anthocyanin and polyphenolics in purple sweetpotatoes cultivated in different locations; I (42°92′ N, 143°04′ E), II (35°99′ N, 140°01′ E), and III (31°72′ N, 131°03′ E), were compared over two years. Total anthocyanin and polyphenolic contents in purple sweetpotatoes tended to be high in location I. Their contents significantly differed over the two years in locations I and III and was dependent on temperature during cultivation. The anthocyanin and polyphenolic compositions differed between locations. The peonidin/cyanidin ratios were higher in location III compared with I and II in all varieties. The relative amount of chlorogenic acid was higher in location I, while the amount of 3,4- and 4,5-dicaffeoyolquinic acids were higher in location III, suggesting that the variability of the anthocyanin and polyphenolic content and composition was dependent on cultivation conditions. This study suggested that northern areas in Japan are an alternative production area and may yield higher amounts of anthocyanin and polyphenolics.

This paper addresses the difficulty of balancing real-time response and low power consumption in intelligent manhole cover application scenarios. It proposes a method to distinguish normal and abnormal events by segmenting the boundary where the acceleration of the intelligent manhole cover deviates from a set threshold and lasts for a certain period, based on the difference in vibration patterns of the intelligent manhole cover when a normal event and an abnormal event occur. This paper uses digital output motion sensor data autonomous data fusion to implement the pattern mentioned above recognition algorithm, which reduces the MCU computing and working time and the overall power consumption of the system while meeting the real-time response requirements. The test results demonstrate that the method has a high rate of anomaly recognition accuracy. The method ensures the system's real-time response capability, and the actual low power consumption test demonstrates that the device can operate continuously for 9.5 years. The low power consumption index exceeds the requirements of the existing national standard, thereby resolving the issue that it is challenging to balance intelligent manhole cover abnormality recognition and low power consumption.

In addition to provide an extremely clean environment for primary loop of high-temperature gas-cooled reactor (HTR), the primary helium circulator (PHC) using electromagnetic levitation technology also provides an effective means for vibration control. Besides synchronous vibration produced by mass imbalance and sensor runout, double-frequency vibration produced by unbalanced magnetic pull (UMP) is serious in PHC engineering prototype (PHC-EP). In this paper, we firstly analyzed the mechanism of UMP and the multi-frequency vibration characteristics in combination with the PHC-EP. Then we put forward a distributed iterative learning control (ILC) algorithm and a parallel control scheme to suppress the periodic vibrations. Finally, we verified the methods by carrying out experimental researches on the active magnetic bearing (AMB) bench of PHC-EP. The results show that the methods put forward in this paper have significant control effect on the double-frequency vibration generated by UMP of the PHC-EP, and provide theoretical and practical references for the PHC safe operation in HTR.

A novel verifiable privacy preservation scheme for outsourcing medical image to cloud through ROI based crypto-watermarking is proposed in the paper. In the proposed scheme, data owner firstly carries out substitution of S-box for the region of interest (ROI) of medical image, and then separates the image into 4 most significant bits (MSBs) plane and 4 least significant bits (LSBs) plane images. Secondly, the hash value of ROI is embedded into the two separated bit plane images using reversible watermarking algorithm. Lastly, some selected hash values are transformed into the initial parameters of chaotic maps, and the two sharing secrets, which are produced through chaos based encryption algorithm, are finally outsourced to two different cloud servers. For authorized users, they can get shares from different cloud servers, and then can losslessly recover the original medical image through a series of decryption operations and extraction of watermarking. Furthermore, the users can verify whether the original image is completely reconstructed or not, they even can locate the tampered parts inside ROI if anyone of the sharing secrets is damaged. Some experiments analyses and comparisons are given to show the security and effectiveness of proposed scheme.

This study investigated the effects of soil crust development on the underlying soil properties. The field sampling work was conducted in June 2016 in the Hobq Desert in Inner Mongolia, North China. Soil crust samples and 0–6, 6–12, 12–18, 18–24, 24–30 cm deep underlying soil samples were taken from five representative areas of different soil crust development stages. All samples were analyzed for physicochemical properties including water content, bulk density, aggregate content, organic matter content, enzyme activities, and microbial biomass carbon and nitrogen. The results showed that the thickness, water content, macroaggregate (>250 μm) content, organic matter content, microbial biomass and enzyme activities of the soil crusts gradually increased along the soil crust development gradient, while the bulk density of the soil crusts decreased. Meanwhile, the physicochemical and biological properties of the soils below the algal and moss crusts were significantly ameliorated when compared with the physical crust. Moreover, the amelioration effects were significant in the upper horizons (approx. 0–12 cm deep) and diminished quickly in the deeper soil layers.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

Background: Pleurotus ostreutus is one of the world’s most commonly consumed mushrooms. Cultivation of mushrooms using wood resources usually results in environmental issues of deforestation. Juncao grass Pennisetum sp, Arundo Donax, and Methodology: Miscanthus are the culture mediums used in this research which offered a composting system most particularly for a simple formulation, cheap and feasible for small farms in cultivating oyster mushrooms. Results: The present study assessed the different junco grass as a substrate for growing Pleurotus ostreatus given the enzyme activities, growth, and yields. In addition, on the other hand, Lignin peroxidase (LiP) was the most active enzyme in each culture material among the other enzyme activities expressed differently between substrate and growing stages. Fruiting bodies harvested on giant grass,Arundo donax,and miscanthus,substrate weighed 159.2g/bag,132g/bag, and 65.1g/bag on average respectively. The biological efficiency of pleurotus cultivated in three different substrates was 75.2%, 63.4%, and 28.7%, respectively. Lignin peroxidase (LiP) was the most active enzyme followed by Laccase in each substrate. At the same time, other enzyme activities were differently expressed between substrate and different developmental stages. Nutrient analysis revealed significant variations, with differences in polysaccharides, proteins, and amino acids among substrates as well as the presence of heavy metals as arsenic, lead, mercury, and cadmium content in all samples was within safe limits. Conclusion: Findings from this study will serve as a solid foundation for future studies aimed at characterizing different substrate responses on enzyme activity. This research provides a sustainable footprint for subsequent research promoting eco-friendly mushroom production. The obtained results indicate that Arundo donax should be a good substrate in place of giant grass, using miscanthus is not productive based on the results obtained in this research the juncao grasses offer a sustainable approach that reduces reliance on wood-based substrates and enhances environmental sustainability.

A novel nano-laminated GdB2C2 material was successfully synthesized using GdH2, B4C, and C via an in-situ solid state reaction approach for the first time. The formation mechanism of GdB2C2 was revealed based on the microstructure and phase evolution investigation. A purity of 96.4 wt. % GdB2C2 was obtained at a low temperature of 1500 ℃, while a near full pure GdB2C2 can be obtained at a temperature over 1700 ℃. The as-obtained GdB2C2 presented excellent thermal stability at high temperature of 2100 ℃ in Ar atmosphere due to the stable frame work formed by the high covalent four-members and eight-members B-C rings in GdB2C2. The minimum reflection loss value (RLmin) of -47.01 dB with an effective absorption bandwidth (EAB) of 1.76 GHz at a thickness of 3.44 mm was obtained for the GdB2C2 synthesized at 1500 ℃. The possible EMWA mechanism could be ascribed to the nano-laminated structure and appropriate electrical conductivity, which facilitated to the good impedance matching, remarkable conduction loss, interfacial polarization as well as multiple interface reflection and scattering. The as-obtained GdB2C2, with excellent EMWA performance as well as remarkable ultra-high temperature thermal stability, could be a promising candidate for the EMWA materials applications in extreme ultra-high temperatures.

A simple and rapid method for efficient synthesis of sulfonyl chlorides/bromides from sulfonyl hydrazide with NXS (X = Cl or Br) and late-stage conversion to several other functional groups has been described. A variety of nucleophiles could be engaged in this transformation thus permitting the synthesis of complex sulfonamides, sulfonates. In most cases, these reactions are highly selective, simple, and clean, affording products in excellent yields.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

Previous research has indicated that ultra-high pressure (UHP) technology is useful in speeding up the extraction process of cold brew (CB) coffee. However, the impact of different degrees of roasting on UHP CB coffee is still unclear. Therefore, this study aimed to investigate the effects of three different degrees of roasting (light, medium, and dark) on the physicochemical and flavor characteristics of UHP CB coffee. The results of this study showed that most physicochemical characteristics of UHP coffee were similar to those of conventional CB coffee, regardless of the degree of roasting. However, the majority of physicochemical characteristics, non-volatile components, and sensory evaluation significantly increased with an increase in roasting degree. The HS-SPME-GC/MS analysis showed that most volatile components, such as pyrazines, furans (except furfural), esters, pyrrole, pyridine, and most aldehydes, increased from light to dark roasting, and this was significantly evident in CB coffee compared with UHP. The content of volatile components in UHP coffee was significantly (P<0.05) higher than that in CB coffee at the same degree of roasting, especially with dark roasting. The combination of orthogonal partial least squares-discriminant analysis (OPLS-DA) and principal component analysis (PCA) indicated that the distance between coffee samples at different degrees of roasting under CB coffee was greater than that under UHP coffee. However, the distance between these two extraction methods at medium roasting was evidently closer than that at light and dark roasting. Moreover, 15 representative differential compounds, such as were Hazelnut pyrazine, linalool, butane-2,3-dione, 3- methylbutanal found by the calculation of odor-active values (OAVs) indicating the main contributing compounds to odor. Overall, the effect of roasting degrees on UHP coffee was less than that on CB coffee, which was consistent with the results of physicochemical characteristics, volatile components, and sensory evaluation.

In the new period, the state has made every effort to promote the new urbanization of public sports service. Entropy method, coupled coordination model, cold hot spot analysis is used to explore the dynamic relationship between public sports services and the development of new urbanization in China from 2008 to 2017. The results show that: (1) The development of the internal subsystem of public sports service is not balanced, the sports financial investment system grows rapidly, but the development of professional sports talent team is slow. (2) The imbalance of regional development cannot be ignored, and the public sports service level shows a decreasing gradient from east to west. (3) The regional development features are different. The eastern region is dominated by the coordinated development of sports public service and urbanization, while the central region is mainly in the type of public sports service lag, while the western region has multiple complex characteristics of low-level coordination and public sports service lag. Therefore, it is proposed that the construction of modern public sports service system should be investigated in the context of the development of new urbanization. It should be promoted from the following aspects: promoting the extension of public sports service to rural areas, engendering the "citizen's right" of sports health to the migrant population, conforming to the trend of mass sports intelligence, developing green sports and revitalizing idle sports assets in cities.

Climate change is one of the biggest challenges of our times. Its impact on human populations is not yet completely understood. Many studies have focused on single aspects with contradictory observations. However, climate change is a complex phoenomenon that cannot be adequately addressed from a single discipline's perspective. Hence, we propose a comprehensive conceptual framework on the relationships between climate change and human responses. This framework includes biological, psychological and behavioural aspects, and provides a multidisciplinary overview and critical information for focused interventions. The role of tipping points and regime shifts is explored, and a historical perspective is presented to describe the relationship between climate evolution and socio-cultural crisis. Vulnerability, resilience and adaptation are analyzed from an individual and a community point of view. Finally, emergent behaviours and mass effect phenomena are examined that account for mental maladjustment and conflicts.

We propose a novel plasmon nano-optical antenna that consists of three vertically superimposed discs with different materials. Two symmetrical nanometer-scale Yagi antenna elements with gold-material are embedded into the surface of the middle disc with silicon dioxide. Based on plasmon theory and Yagi antenna principle, we explore the properties of the far-field radiation and near-field transmission of the antenna in near infrared band. It is found that the pattern of the xoy plane in the antenna can be adjusted in arbitrary direction. The far-field pattern and near-field transmission spectrum can be reconfigured by changing the angle a of the Yagi antenna elements in the middle disc. Moreover, we also discuss the influences of the widths and lengths of the elements on the near-field transmission spectrum when a is fixed at 0 degree.

In recent years, electroencephalogram (EEG) emotion recognition has emerged as a research hotspot in the field of artificial intelligence (AI). Despite advancements in EEG-based emotion recognition, room for enhancing performance persists due to EEG signal redundancy and limitations in feature extraction, leading to inefficient models and emotional information loss. To fully utilize EEG's emotional information and improve recognition accuracy while reducing computational costs, this paper proposes a Convolutional-Recurrent Hybrid Network with a dual-stream adaptive approach and an attention mechanism (CSA-SA-CRTNN). Firstly, the model utilizes a CSAM module to assign corresponding weights to EEG channels. Then, an adaptive dual-stream convolutional-recurrent network (SA-CRNN and MHSA-CRNN) is applied to extract local spatial-temporal features. After that, the extracted local features are concatenated and fed into a temporal convolutional network with a multi-head self-attention mechanism (MHSA-TCN) to capture global information. Finally, the extracted EEG information is used for emotion classification. We conducted binary and ternary classification experiments on the DEAP dataset, achieving 99.26% and 99.15% accuracy for arousal and valence in binary classification, and 97.69% and 98.05% in ternary classification, surpassing relevant algorithms. Additionally, the model's efficiency is significantly higher than other models, achieving better accuracy with lower resource consumption.

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

The pressing threat of global warming poses significant risks to plant survival, adversely affecting their growth and agricultural productivity. It is crucial to understand how plants react to heat stress at the molecular level to develop crops that can withstand higher temperatures. In our study, we investigated the proteome dynamics of *Arabidopsis thaliana* seedlings under moderate heat stress conditions (30°C) using a combination of 15N-stable isotope labeling and the ProteinTurnover algorithm. This approach allowed us to closely examine the proteomic changes across different cellular compartments. Our findings revealed significant changes in the turnover rates of 571 proteins, with an average increase of 1.4-fold, indicating enhanced protein dynamics under heat stress. Notably, root soluble proteins showed more subtle changes, suggesting tissue-specific responses. We also detected significant turnover variations in proteins involved in redox signaling, stress response, and metabolism, highlighting the complex nature of these adaptive mechanisms. In contrast, proteins related to carbohydrate metabolism and mitochondrial ATP synthesis showed little change, underscoring their stability. This detailed analysis illuminates the proteomic adaptations of *Arabidopsis* seedlings to moderate heat stress, enhancing our understanding of plant thermal resilience and supporting efforts to develop thermotolerant crops.

Based on the topology of wide area protection system (WAPS), after studying the reliability of hardware system and information flow in the WAPS and establishing the reliability assessment model, the multi-service reliability analysis method with multi monitoring and protection tasks in WAPS was proposed. In the model, the impact of network quality of service (QoS) such as information flow loss and delay, is studied. On the base of the model, the multi-service reliability evaluation method is employed to analyze the reliability of a WAPS of IEEE14 node power system, and the key nodes of the WAPS is given, which provides a basis for improving the reliability of the WAPS.

Brain metastasis (BrM), involving the spread of cells from a primary tumor through the blood circulation system to the brain microvasculature, eventually progresses despite multiple treatments and remains a substantial contributor to major mortality in patients with advanced- stage cancer. Molecular signatures and immune cellular components of the tumor microenvironment (TME) are emerging as essential regulators involved in establishing an organ-specific metastasis (colonization) and therapeutic response. A comprehensive understanding of detailed characterization and the immune landscape in context of process of BrM formation will greatly expand the horizon of treatments available to target these deadly diseases. In this review, we provide a comprehensive picture of the complex interactions between tumor cells and immune cellular components participated in the BrM process. Based on this knowledge, we will discuss opportunities and challenges for therapeutic strategies against BrM.

Objective: To investigate the protein expression levels of cyclin‑dependent kinase subunit 2 (CKS2) and cluster of differentiation (CD) 47 in gastric cancer (GC) and their clinical significances. Methods: A total of 126 GC patients who underwent radical resection were selected as study subjects. Additionally, 32 patients with benign gastric tumor, 42 patients with low-grade intraepithelial neoplasia (LGIEN), and 49 patients with high-grade intraepithelial neoplasia (HGIEN) who underwent surgery were selected as the control groups. Immunohistochemistry was used to detect the expression of CKS2 and CD47 in surgical specimens. We statistically analyzed the clinical significance of the expression of the two factors. Results: (1) The positivity rates for CKS2 in benign gastric tumor tissue, LGIEN tissue, HGIEN tissue, and GC tissue gradually increased, i.e., 6.3% (2/32), 30.9% (13/42), 38.8% (19/49), and 60.3% (76/126), respectively, and the positivity rates for CD47 were 18.8% (6/32), 38.1% (16/42), 46.9% (23/49), and 65.9% (83/126), respectively. (2) High expression of CKS2 and CD47 were associated with tumor diameter, Lauren classification, number of lymph node metastases, and TNM stage. In addition, the immunohistochemical scores for CKS2 and CD47 were positively correlated (r=0.625, P=0.000). (3) The median follow-up time of 126 patients was 46.5 months, and the overall survival rate was 40.5% (51/126). Survival analysis showed that compared with that in the CKS2 (-) group, the overall survival rate for patients in the CKS2 (+) group was significantly worse (25.0% vs 64.0%, 2=15.67, P=0.000) and that compared with the CD47 (-) group, the CD47 (+) group had significantly worse overall survival (30.1% vs 60.5%, 2=15.67, P=0.000). (4) The overall survival rates of CKS2(+)CD47(+) group, CKS2(+)CD47(-) group, CKS2(-)CD47(+) group, and CKS2 (-)CD47 (-) group were 20.0%(13/65), 58.3%(7/12), 57.1%(8/14), 65.7% (23/35), respectively, the prognosis of patients in CKS2(+)CD47(+) group was significantly poor. Conclusion: High expression levels of CKS2 and CD47 were closely related to the occurrence of GC and can be used as independent risk factors to assess the prognosis of patients.

Research has shown a protective association between social support and depression, depression among stroke patients, and health impacts of depression. Yet not much is known on the effect of social support on depression among stroke patients. This review aims to summarize the current research examining the association between social support and depression among stroke patients. A literature search was performed in PubMed to find original peer-reviewed journal articles from 2016 to Mar. 12, 2023 that examined the association between social support and depression among stroke patients. The search terms were depression and "social support" and stroke, which lead to 172 articles. After abstract review, seven observational studies that studied the target association among stroke patients were selected. One additional study was found using PsycINFO as a complementary source with the same search strategy and criteria. Overall, a negative association was found between social support and depression among stroke patients in seven studies, with more social support leading to lower rates of depression post-stroke. One study found that social support was positively related with depression, but the result was nonsignificant. Overall, the results of recent studies suggest that social support is negatively associated with depression among stroke patients. In most studies, this association was statistically significant. The findings suggest the importance of improving social support perceived by stroke patients in the prevention of depression after the occurrence of stroke.

A wealth of Full Waveform (FW) LiDAR data are available to the public from different sources, which is poised to boost the extensive application of FW LiDAR data. However, we lack a handy and open source tool that can be used by potential users for processing and analyzing FW LiDAR data. To this end, we introduce waveformlidar, an R package dedicated to FW LiDAR processing, analysis and visualization as a solution to the constraint. Specifically, this package provides several commonly used waveform processing methods such as Gaussian, adaptive Gaussian and Weibull decompositions, and deconvolution approaches (Gold and Richard-Lucy (RL)) with users’ customized settings. In addition, we also developed functions to derive commonly used waveform metrics for characterizing vegetation structure. Moreover, a new way to directly visualize FW LiDAR data is developed through converting waveforms into points to form the Hyper Point cloud (HPC), which can be easily adopted and subsequently analyzed with existing discrete-return LiDAR processing tools such as LAStools and FUSION. Basic explorations of the HPC such as 3D voxelization of the HPC and conversion from original waveforms to composite waveforms are also available in this package. All of these functions are developed based on small-footprint FW LiDAR data, but they can be easily transplanted to the large footprint FW LiDAR data such as Geoscience Laser Altimeter System (GLAS) and Global Ecosystem Dynamics Investigation (GEDI) data analysis. It is anticipated that these functions will facilitate the widespread use of FW LiDAR and be beneficial for better estimating biomass and characterizing vegetation structure at various scales. The package and code examples can be found at https://github.com/tankwin08/waveformlidar.

Lyme disease, the leading vector-borne ailment in the U.S., annually affects an estimated 476,000 individuals, predominantly in the Northeast and Upper Midwest. Despite its increasing incidence, the evaluation of risk within U.S. cities, including natural public lands, remains inadequate. This study focuses on blacklegged tick occurrences and Borrelia burgdorferi infection prevalence in 24 Staten Island parks, aiming to assess Lyme disease exposure risk. Monthly acarological risk index (ARI) calculations from 2019 to 2022 revealed elevated values (0.16-0.53) in specific parks, notably Wolfe’s Pond Park, High Rock Park, Clay Pit Pond Park, Clove Lake Park, and Fair View Park. June (0.36) and November (0.21) consistently exhibited heightened ARIs, aligning with peak tick collection months. Despite stable yearly infection rates at 28.97%, tick densities varied significantly between parks and years. Identifying a high transmission risk in specific parks in Staten Island, a highly urbanized part of New York City, emphasizes the continuous necessity for Lyme disease risk management, even within the greenspaces of large cities.

This paper describes the formulations for viscoplasticity of metals based on the Chaboche and Delobelle model. The implementations of the viscoplastic models were detailed herein and then implemented via user subroutines for material models (UMAT) in ABAQUS. Two typical metals, i.e., 316 Stainless Steel and Zircaloy-4, were chosen as examples and their viscoplastic behaviors were captured. Numerical simulations are compared to reported experiments to validate the models and the UMAT codes. Typical viscoplastic behaviors of both metals, such as stress relaxation and creep, were captured well against available experiments. We publicize all the data and codes via: https://github.com/XJTU-Zhou-group/ABAQUS_UMAT_316ss_Zr4.

Current adaptive cruise control (ACC) systems adopt fixed desired time headway, which leads to an abrupt speed reduction after being cut-in by a lane changer in front or when changing lanes too close to the new leader. In contrast, human drivers behave differently and feature a variable spacing within 20 or 30 seconds right after a cut-in or lane change. Motivated by the smooth transition found in driver relaxation, the paper aims to incorporate relaxation into ACC systems. Based on the open-source ACC platform, Openpilot, Comma.ai, the paper proposes a feasible relaxation model compatible with current factory ACCs, which has also been tested using a market car with stock ACC hardware. The study further investigates the impact of relaxation ACC on traffic operation. Numerical simulation suggests that incorporating relaxation into ACC can help: i) reduce the magnitude of speed perturbations in both cut-in vehicles and followers; ii) stabilize the lane-changing traffic by reducing the speed variance and prevent the lateral propagation of congestion, and iii) increase the average vehicle speed and capacity in merging traffic.

Traditional potential transformers have problems of large volume, difficulty in insulation, iron core saturation, ferroresonance overvoltage and poor transient response characteristics. The voltage sensor based on the principle of electric field coupling and differential input structure does not need to contact the measured object or ground, and can avoid the above problems. However, it requires a sufficiently high capacitance between the differential electrodes to obtain sufficient accuracy and a high voltage division ratio. The existing method of using mutual capacitance between the differential electrodes will cause many problems and fail to meet the practical needs. To solve the above problems, this paper innovatively uses multi-layer ceramic capacitor to replace the mutual capacitance and designs a new type of voltage sensor. In addition, by using single bypass small resistance grounding method to increase the input impedance of the differential signal processing circuit, error of the sensor is further reduced. The experimental results show that the sensor has excellent accuracy and great transient response characteristics. The ratio error under power frequency is within ±0.5% and the phase error is within 1. The ratio error in the range of 500 Hz∼30 kHz is within ±5% and the phase error is within 5. Moreover, it has the advantages of low cost, miniaturization, flexible shape and easy to adjust the voltage division ratio. These characteristics indicate that the sensor has good voltage measurement and sensor network potential.

Seeds stored for a prolonged period are subject to aging and reduction in germination potential (GP), which will negatively affect seed sales. Rare-earth elements have a synergistic effect on the improvement of seed GP. In this study, we examined the effects of neodymium on biochemical components, the antioxidant protective system, and metabolism-related enzymes during germination of naturally and artificially aged seeds of three wheat cultivars. Seed germination indices, biochemical substance contents, and enzyme activities decreased after seed aging. Soaking seeds in neodymium nitrate solution revived aged wheat seeds at an optimal concentration of 20 µmol/L for 8 h. Soaking in neodymium nitrate solution increased the GP (by 2.25%–60.9%), germination index (by 1.69%–29.2%), and vigor index (by 3.36%–18.7%) of aged seeds. Compared with non-soaked seeds, soaking significantly changed the contents of biochemical substances, and the activities of antioxidant protective enzymes and metabolic enzymes in seedlings were increased. Soaking with neodymium may revive aged seeds by regulating the synthesis of soluble sugars, soluble proteins, chlorophyll, and carotenoids, and decomposing malondialdehyde, in the germinating seed. Root dehydrogenase and amylase showed different responses to the aging modes. The differential responses of root dehydrogenase and amylase may reflect differences in the resistance of enzymes to long-term mild seed aging and short-term severe environmental aging.

The determination of a causal relationship between gut microbiota and a range of dyslipidemia remains uncertain. To clarify these associations, we employed a two-sample mendelian randomization (MR) analysis utilizing the inverse-variance weighted (IVW) method. This comprehensive analysis investigated the genetic variants that exhibited a significant association (p&lt;1e-5) with 129 distinct gut microbiota genera, and their potential link to diverse forms of dyslipidemia. The results indicated a potential causal relationship between 22 gut microbiota genera and dyslipidemia in humans. Furthermore, these findings suggested that the impact of gut microbiota on dyslipidemia regulation is dependent on the specific phylum, family, and genus. Bacillota phylum demonstrated the greatest diversity, with 15 distinct genera distributed among 8 families. Notably, gut microbiota derived from the Lachnospiraceae and Lactobacillaceae families exhibit statistically significant associations with lipid levels that contribute to overall health (p&lt;0.05). The sensitivity analysis indicated that our findings possess robustness (p&gt;0.05). The findings of our investigation provide compelling evidence that supports a causal relationship between the gut microbiota and dyslipidemia in the human body. It is noteworthy to highlight the significant influence of the Bacillota phylum as a pivotal regulator of lipid levels, and the families Lachnospiraceae and Lactobacillaceae should be acknowledged as probiotics that make substantial contributions to this metabolic process.