This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Highly diverse agroecosystems are increasingly of interest as the realization of farms' invaluable ecosystem services grows. Simultaneously there has been an increased use of uncrewed aerial systems (UAS) in remote sensing as drones offer a finer spatial resolution and faster revisit rate than traditional satellites. With the combined utility of UAS and the attention on agroecosystems, there exists an opportunity to assess UAS practicality in highly biodiverse settings.  In this study, we utilized UAS to collect fine-resolution 10-band multispectral imagery of coffee agroecosystems in Puerto Rico. We created land cover maps through a pixel-based supervised classification of each farm and assembled accuracy assessments for each classification. To bolster our understanding of the classifications, we interviewed farmers to understand their thoughts on how these maps may be best used to support their land management. The average overall accuracy (53.9%), though relatively low, was expected for such a diverse landscape with fine-resolution data. After sharing imagery and land cover classifications with farmers, we found that while the prints were often a point of pride or curiosity for farmers, integrating the maps into farm management was perceived as impractical. These findings highlight that while remote sensing of diverse agroecosystems may provide a detailed way of estimating land cover classes and ecosystem services for researchers and government agencies for example these maps may be of limited use to land managers without additional interpretation.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

Background: Only few studies have studied the link between risk perception and sleep in the context of the COVID-19 pandemic. This study investigates the effect of two distinct risk appraisals—risk perception and perception of collective coordinated defense (PCCD) on Chinese adults’ sleep quality during the COVID-19 pandemic, and tested COVID-19-related fear and rumination as potential mediators of the relationships. Methods: Data were collected using a self-report online questionnaire from a sample of 224 Chinese adults during the fourth wave of the COVID-19 pandemic in Hong Kong. Results: COVID-19 risk perception and PCCD were related to poor sleep quality. Mediation analysis showed that both fear and rumination mediated the relationship between risk perception and sleep quality, whereas only fear mediated the relationship between PCCD and sleep quality. The model showed an excellent fit to the data and accounted for 44% of the variance in sleep quality in Chinese adults. Conclusions: This study demonstrates the distinct perceptual processes—risk appraisals in particular—contributed to poor sleep quality in Chinese adults during the COVID-19 public emergencies. These findings would be helpful for policy makers to address the sleep problems induced by psychological consequences of the pandemic.

Many lifestyle and occupational habits negatively impact on physical and mental health, increasing the risk of cardiovascular and other diseases. While larger institutions fulfill occupational health requirements to ensure their employees’ wellbeing at work, smaller business workers and entrepreneurs may neglect initial signs of stress or physical decline, putting themselves at increased risk. Early detection of compromised cardiopulmonary health or fitness has the potential to flag up indications for early interventions and reduce the risk of disease onset and progression. This case study highlights the usefulness of respiratory muscle training (RMT) in improving pulmonary and cardiovascular parameters as an early countermeasure to cardiopulmonary decline. We suggest RMT as an easily accessible, cost- and time effective opportunity to support a healthy lifestyle.

The aim of this study was to evaluate the Hapo ms, a passive upper limbs exoskeleton developed to assist workers for tasks with arms in front of the body. Twelve participants had to perform a static task, a manual handling task and a load carrying task two times: with and without the exoskeleton. In all cases subjective (perceived effort in arm and back areas, comfort) and objective (muscular activity, postural balance) criteria were evaluated. Results have shown a decrease in anterior deltoid (-12 to -18% depending of the task) and in biceps brachii (-19% to -33% depending of the task) muscular activity. No significant difference was pointed out in back muscle and postural balance was not significantly perturbed due to the wear of the exoskeleton. Finally, perceived effort reduction was observed during the three tasks (except in back area for task 1). To conclude, the Hapo ms seems well adapted to assist upper arms during tasks with arms in front of the body.

Global financial investments in energy production and consumption are significant since all aspects of a country's economic activity, and development require energy resources. In this paper, we assess the investment trends in the global energy sector during, before and after financial crises of 2008 using two data sources: (1) Dealogic database providing cross‐border mergers and acquisitions (M&As), and (2) fDi Intelligence fDi Markets database providing greenfield (GF) foreign direct investments (FDIs). We highlight the changing role of China and compare its M&A and GF FDI activities to those of the United States, Germany, UK, Japan and others during this period. We analyze the investments along each segment of the energy supply chain of these countries to highlight the geographical origin and destination, sectoral distribution, and cross‐border M&As and GF FDI activities. Our paper shows that while energy accounts for nearly 25% of all GF FDI, it only accounts for 4.82% of total M&A FDI activity in the period 1996-2016. China's outbound FDI in the energy sector started its ascent around the time of the global recession and had accelerated in the post-recession phase. In the energy sector, the development of China's outbound cross‐border M&As is similar to USA or UK, located mostly in the developed countries in the west, while their outbound GF investments are spread across many countries around the world. Also, China's outbound energy M&As are concentrated in certain segments (extraction, and electricity generation) while their GF covers all segments of the energy supply chain.

We find that the standard relative entropy and the Umegaki entropy are designed for the purpose of inferentially updating probability and density matrices respectively. From the same set of inferentially guided design criteria, both of the previously stated entropies are derived in parallel. This formulates a quantum maximum entropy method for the purpose of inferring density matrices in the absence of complete information.

: Extra- and intra-cellular activity occurs under the direction of numerous inter-molecular interactions, and in any tissue or cell, molecules are densely packed, thus promoting those molecular interactions. Galectins and chemokines, the focus of this review, are small, protein effector molecules that mediate various cellular functions, in particular cell adhesion and migration, as well as cell signaling/activation. In the past, researchers have reported that combinations of these (and other) effector molecules act separately, yet sometimes in concert, but nevertheless physically apart and via their individual cell receptors. This view that each effector molecule functions independently of the other limits our thinking about functional versatility and cooperation, and, in turn, ignores the prospect of physiologically important inter-molecular interactions, especially when both molecules are present or co-expressed in the same cellular environment. This review is focused on such protein-protein interactions with chemokines and galectins, their homo- and hetero-oligomeric structures that they can form, and the functional consequences of those paired interactions.

Current therapeutic strategies targeting cancer cells within solid tumors have displayed limited success owing to the presence of non-cancer components referred to as the tumor stroma within the tumor microenvironment (TM). These stromal cells, extracellular matrix and blood vessels influence cancer cell response to therapy and play key roles in tumor relapse and resistance. Of the stromal cells present in the TM, a lot of attention has been given to cancer-associated fibroblasts (CAFs) as they are the most abundant and are important in cancer initiation, progression and therapy resistance. In this updated review I emphasize the role of CAFs in the regulation of tumor cell behaviour and reveal how CAF-derived factors and signaling influence tumor cell heterogeneity and development of novel strategies to combat cancer. To investigate the expression of CAF markers in tumor tissues versus normal tissues, transcriptomic data from The Cancer Genome Atlas (TCGA) and the Gene Expression Profiling Interactive Analysis (GEPIA) databases was used. Bioinformatic analysis reveals differential expression of CAF markers in several cancer types, underscoring the need for further multiomics and biochemical studies on CAFs, CAF subsets and markers. Differences in CAF markers’ expression could be due to different cellular origins as well as the effect of cancer-specific tumor microenvironmental effect on CAFs. Lastly, I present recent advances in therapeutic targeting of CAFs and the success of such endeavours or its lack thereof. It is recommended that for patients’ outcomes to improve, cancer treatment be combinatorial in nature, targeting both cancer cells and stromal cells and interactions.

In this paper, we present a new stress calculation method for flexible structures, particularly, the tensile armors, and apply it to flexible riser fatigue analysis. The method is based on a 3-dimensional curved bar theory. First, the tensile armor center line was described as a cylindrical helix curve, its bended curve length and bending migration length were derived and studied under different friction scenarios. Second, the tensile and bending stiffness was given with consideration of frictional hysteretic effect, and verified through FEA analysis results. Third, we presented the stress calculation formula for tensile armor under tension and bending load. All stress components are considered, including tensile, bending and shear stresses. Fourth, the method was benchmarked with published experimental results on a flexible prototype tension and bending tests, and comparisons showed general agreements. Fifth, the method is further applied to a 8” flexible riser for fatigue assessment and lifetime extension evaluation, and showed the flexible riser has sufficient remaining fatigue life, and is suitable to continue its service under the current operating conditions. Last, conclusions are drawn. It concluded that the presented tensile armor stress calculation method and modelling techniques are valid for flexible riser fatigue analysis. This method is time efficient, and can be implemented into other multi-scale models for riser dynamic analysis. It is also applicable to other similar helix structure stress analysis, such as wire ropes, submarine hoses, and subsea umbilicals.

Many cellular functions important for tumor initiation and progression are mediated by members of the integrin family, a diverse family of cell adhesion receptors. With recent studies emphasising on the role of the tumor microenvironment (TME) in tumor initiation and progression, it is not surprising that a lot of attention is being given to integrins. Several integrins are under trial with many demonstrating appealing activity in patients with different cancers. A deeper knowledge of the functions of integrins within the tumor microenvironment is still required, and might lead to better inhibitors being discovered. Integrin expression is commonly dysregulated in many tumors with integrins playing key roles in signaling as well as promotion of tumor cell invasion and migration. This review report new data on the differential expression of integrins within solid tumors using two publicly available resources: The Cancer Genomic Atlas (TCGA) and Gene Expression Profiling Interactive Analysis (GEPIA). In this analysis, I investigated the expression of integrin alpha 2 (ITGα2), ITGα3, ITGβ4 and ITGβ6 in tumor tissues versus adjacent normal tissues. This analysis showed that integrins were differentially expressed in cervical squamous cell carcinoma (CESC), head and neck squamous cell carcinoma (HNSC), esophageal carcinoma (ESCA) and lung adenocarcinoma (LUAD). This analysis showed that ITGα2 and ITGβ6 expression are upregulated in CESC and ESCA, ITGα3 is upregulated in HNSC and ESCA whilst ITGβ4 is highly expressed in CESC, HNSC, ESCA and LUAD tumor tissues compared to adjacent normal tissues. Integrins also play a major role in adhesion of circulating tumor cells to new sites and the resulting formation of secondary tumors. Furthermore, integrins have demonstrated the ability to promoting stem cell-like properties in tumor cells as well as drug resistance. Anti-integrin therapies rely heavily on the doses or concentrations used as these determine whether the drugs act as antagonists or as integrin agonists. This review offers the latest synthesis in terms of current knowledge of integrins functions within the tumor microenvironment and potential targets for different cancers.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

Human-Computer Interaction, including technology-aided instruction, is beginning to focus on virtual reality (VR) technology due to its ability to support immersive learning, teaching through simulation, and gamification of learning. These systems can deliver high-level multisensory learning experiences that are important in the teaching of many subjects, especially those involving abstract concepts or requiring spatial skills, such as organic chemistry. Haptic experiences with VR, however, remain a challenge. In addition, development have focused on general entertainment/gaming; VR systems in chemistry implement simulations of the chemistry laboratory and other advanced systems whereas those that support safe, game-like, immersive and multisensory learning of organic chemistry with haptics at pre-university education levels are scarce. We developed the VR Multisensory Classroom (VRMC) as an immersive learning environment within a VR head-mounted display, where learners employ hand movements to build hydrocarbon molecules and experience haptic feedback through gloves with built-in sensors and hand-tracking with the Leap Motion system. We report here the evaluation of the first prototype by learners from diverse backgrounds who reported on the ability of the VRMC to support high engagement, motivation, interest and organic chemistry learning as well as diverse learning styles. The VRMC is a novel VR classroom that supports immersive learning in molecular organic chemistry with haptics for multisensory learning.

This paper defines the two main causes of global warming in the UK and seeks to cut climate change using green hydrogen made from renewable electricity sources. Combustion vehicles powered by fossil gasoline and diesel emit a third of UK climate-warming CO2 while buildings heated by natural gas provide a quarter. First, current UK grid problems are defined: Electricity grid, gas grid and petroleum grid. Then experiments on the private energy community of Keele University allow electrolysis demonstrations producing green hydrogen for buildings and vehicle refueling. Next, the model supply chain is planned and tested. Finally, experiments and calculations are outlined, analyzing the optimum system design criteria proposed. We conclude that economic green hydrogen can displace diesel and gasoline in vehicle transport, while also displacing natural gas for combined heat and power in buildings. In addition, the prospect in 2023 is that profits can now be made all along the green hydrogen supply chain, such that new businesses involved in clean communities can beat the National Grid monopoly and other large dominant fossil grid companies.

Early reports demonstrated the presence of cells with stem-like properties in bone marrow, with these cells having both hematopoietic and mesenchymal lineages. Over the years, various investigations have purified and characterized mesenchymal stromal/stem cells (MSCs) from different human tissues as cells with multi-lineage differentiation potential under the appropriate conditions. Due to their appealing characteristics and potential, MSCs are leveraged in many applications including medicine, oncology, bioprinting and as recent as treatment of COVID-19. To date, reports indicate mesenchymal stromal/stem cells have varied differentiation capabilities into different cell types and demonstrate immunomodulating and anti-inflammatory properties. Reports indicate that different MSCs microenvironments or niche and the resulting heterogeneity may influence their behavior and differentiation capacity. The potential clinical applications of mesenchymal stromal/stem cells have led to an avalanche of research reports on their properties and hundreds of clinical trials being undertaken. The future looks bright and promising for mesenchymal stem cell research with many clinical trials under way to prove their utility in many applications and in the clinic. This report provides an update on the potential broader use of mesenchymal stromal/stem cells, review early observations of the presence of these cells in the bone marrow and their magnificent differentiation capabilities and immunomodulation.

Iron oxide nanozymes are a form of nanomaterial with both superparamagnetic and enzyme-mimicking properties. Given the multifunctional nature of iron oxide nanozymes, it is attractive for creating iron oxide hybrid nanozymes through biomolecular modifications to imbue with auxillary properties. Such iron oxide hybrid nanozymes can be useful for rapid and cost-effective analysis of circulating tumor nucleic acids (ctNAs) in patient liquid biopsies during minimal residual disease (MRD) monitoring of cancer recurrence. Herein, the use of streptavidin-modified iron oxide hybrid nanozymes is reported for magnetic enrichment and bioelectrocatalytic sensing of three prostate cancer (PCa) ctRNA biomarkers with high detection specificity and sensitivity (10 copies) over an ultrabroad dynamic range (five orders of magnitude). Furthermore, the feasibility of ctRNA analysis for pre- and post-cancer treatment MRD monitoring is demonstrated using PCa urinary liquid biopsy samples.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Accurate lithium battery diagnosis and prognosis is critical to increase penetration of electric vehicles and grid-tied storage systems. They are both complex due to the intricate, nonlinear, and path-dependent nature of battery degradation. Data-driven models are anticipated to play a significant role in the behavioral prediction of dynamical systems such as batteries. However, they are often limited by the amount of training data available. In this work, we generated the first big data comprehensive synthetic datasets to train diagnosis and prognosis algorithms. The proof-of-concept datasets are over three orders of magnitude larger than what is currently available in the literature. With benchmark datasets, results from different studies could be easily equated, and the performance of different algorithms can be compared, enhanced, and analyzed extensively. This will expend critical capabilities of current AI algorithms, tools, and techniques to predict scientific data.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

The theories of quantum mechanics and relativity dramatically altered our understanding of the universe ushering in the era of modern physics. Quantum theory deals with objects probabilistically at small scales, whereas relativity deals classically with motion in space and time. We show here that the mathematical structures of quantum theory and of relativity follow together from pure thought, defined and uniquely constrained by the same elementary ``combining and sequencing'' symmetries that underlie standard arithmetic and probability. The key is uncertainty, which inevitably accompanies observation of quantity and imposes the use of pairs of numbers. The symmetries then lead directly to the use of complex \sqrt{-1} arithmetic, the standard calculus of quantum mechanics, and the Lorentz transformations of relativistic spacetime. One dimension of time and three dimensions of space are thus derived as the profound and inevitable framework of physics.

The extracellular matrix (ECM) is a ubiquitous member of the body and is key to the maintenance of tissues and organs integrity. Initially thought to be a by-stander in many cellular processes, the extracellular matrix has been shown to have diverse components that regulate and activate many cellular processes and ultimately influence cell phenotype. Importantly, the ECM composition, architecture, and stiffness/elasticity influence cellular phenotypes. Under normal conditions and during development, the synthesized ECM is constantly undergoing degradation and remodeling processes via the action of matrix proteases that maintain tissue homeostasis. In many pathological conditions including fibrosis and cancer, the ECM synthesis, remodeling, and degradation is dysregulated causing its integrity to be altered. Both physical and chemical cues from the ECM are sensed via receptors including integrins and play key roles in driving cellular proliferation and differentiation and in various disease progression such as cancers. Advances in ‘omics’ technologies have seen an increase in studies focussing on bi-directional cell-matrix interactions and here we highlight emerging knowledge on the role played by the ECM during normal development and in pathological conditions. This review summarizes current ECM-targeted-therapies that can modify tumor ECM to overcome drug resistance and better cancer treatment.

Based on its large surface area and covering the whole human body, the skin body’s largest organ and its main function is protection. Injuries and wound healing involving the skin offer valuable lessons shared with and of relevance to other organ systems and the diseases that impact them. Arguably the most complex human body process, wound healing is a multifaceted process that involves multiple cells and the extracellular matrix (ECM), with each component playing a specific role in the different stages of the healing process. Importantly, studies indicate that cells with stem cell-like properties are present within many of the human tissues and play key roles in case of tissue and cellular injury. Cell-to-cell and cell-to-ECM interactions are salient in wound healing subsequent to an injury. Microenvironment related factors and the variations therein including hypoxia or the abundance of oxygen, the presence/absence of growth factors and cytokines add to the complexity of the wound healing process and impact cell function and result in compromised or enhanced wound healing. This expert review critically examines the advances in biochemical and analytical tools that are enable the analysis of numerous cells and molecules within the wound microenvironment, revealing great cellular heterogeneity as well as novel molecular targets of importance to enhance wound healing. In a broader angle, we emphasize the ways in which wound healing is significant in the search for perfect skin after injury and in many common complex human diseases including cancer. In all, wound healing is a centrepiece of integrative biology research and applications in medicine as well as dermatology as discussed in this review.

More people around the world now have obesity than suffer from starvation thanks to our modern food system. Agriculture was transformed over the 20^th century by a variety of technological advancements that relied heavily on fossil fuels. In the United States of America, government policies and economic incentives led to surplus production of cheap inputs to processed food industries that produced a wide variety of heavily marketed, convenient, rewarding, timesaving, and relatively inexpensive ultra-processed foods. The energy available in the United States food supply increased much more than population needs, albeit with large inequities in food distribution and nutrition security. While most of the rise in per capita food availability during the late 20^th and early 21^st centuries in the United States resulted in increased food waste, a variety of mechanisms have been proposed by which changes in the increasingly ultra-processed food environment resulted in excess energy intake disproportionately in people genetically susceptible to obesity. As populations continue to grow, substantial investments in coordinated nutrition and agricultural research are needed to transform our current food system to one that relies less on fossil fuels, preserves biodiversity, ensures environmental health, and provides equitable access to affordable, safe, and nutritious food that reduces the prevalence of chronic diseases like obesity.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

Celecoxib as adjuvant therapy has been shown in a small randomized trial for Covid-19 to prevent clinical deterioration and rapidly improve thoracic computerized axial tomography (CT-chest)¹. Multiple descriptive trials of high dose famotidine (both inpatient and outpatient) have demonstrated clinical response^2,3,4. We describe the rapid clinical responses after increasing the celecoxib dosage to 400mg bid with high dose famotidine 80mg qid in both a critical inpatient who on baseline required 40 liters per minute high flow nasal insufflation and an outpatient who declined admission but had critical Covid-19 biomarkers.

Fractional differential equations have become a fundamental modelling approach for understanding and simulating the many aspects of nonlocality and spatial heterogeneity of complex materials and systems. Yet, while real-order fractional operators are nowadays widely adopted, little progress has been made in extending such operators to complex-order counterparts. In this work, we introduce new definitions for the complex-order fractional Laplacian, fully consistent with the theory of averaging of smooth functions over fractal sets, and present tailored spectral methods for their numerical treatment. The proposed complex-order operators exhibit a dual particle-wave behaviour, with solutions manifesting wave-like features depending on the magnitude of the imaginary part of the fractional order. Reaction-diffusion systems driven by the complex-order fractional Laplacian exhibit unique spatio-temporal dynamics, such as equilibrium of diffusion in random materials by interference of scattered waves, conduction block and highly fractionated propagation, or the generation of completely novel Turing patterns. Taken together, our results support that the proposed complex-order operators hold unparalleled capabilities to advance the description of multiscale transport phenomena in physical and biological processes highly influenced by the heterogeneity of complex media.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

Molecular dynamics (MD) simulations present a sophisticated nano-scale computational approach that can play a critical role in material design for next generation batteries. One critical piece of information needed for MD simulations is the non-bonded potential parameters, which can be obtained through quantum mechanics (QM) calculations or experimental methods. However, experimental data is not available for exploratory and novel materials to derive the potential parameters. Also, the QM approach needs significant computational power and is too time consuming for large systems. On the other hand, current Artificial Intelligence techniques are faster, but they cannot be generalized across molecules and properties. As a result, there is a significant barrier to discovering and exploring new materials. Overcoming this barrier, in this work, we propose a Machine Learning (ML) based technique that can learn inter-atomic potential parameters for various particle-particle interactions employing QM calculations. This ML model can be used as an alternative for QM calculations for predicting non-bonded interactions in a computationally efficient manner. Using these parameters as input to MD simulations, we can predict a diverse range of properties, enabling researchers to design new and novel materials suitable for various applications in the absence of experimental data. We employ our ML-based technique to learn the Buckingham potential, a non-bonded interatomic potential. Subsequently, we utilize these predicted values to compute the densities of four distinct molecules, achieving an accuracy exceeding 93%. This serves as a strong demonstration of the efficacy of our proposed approach.

10% copper substituted (BiCUVOX/Bi₂V_0.9Cu_0.1O_5.5−δ) and 5% copper/titanium double-substituted bismuth vanadate (BiCUTIVOX/Bi₂V_0.9(Cu_0.05Ti_0.05)O_5.5−δ) platelets were formed by molten salt synthesis (MSS) using a eutectic KCl/NaCl salt mixture. The product was phase pure within the limits of X-ray diffraction. The size and form of the platelets could be controlled by changing the heating temperature and time. The crystallite growth rate at a synthesis temperature of 650 °C, and activation energy for grain growth were determined for BICUTIVOX, which experienced inhibited growth compared to BICUVOX. Quasi-equilibrium, multi-foil shapes consisting of lobes around the perimeter of the platelets were observed and explained in the context of relative two-dimensional nucleation and edge growth rates.

Measuring the impact of land use regulation on the land market involves identifying and classifying relevant impact factors related to the land market. The objective of this study was to identify land market impact factors in the context of the introduction of land use regulation in Nepal. A desktop review was carried out to identify preliminary set of impact factors, which were reclassified through intuitive analysis based on the degree of thematic closeness. Perspective-based impact factors were identified through the qualitative analysis of primary data collected through semi-structured interviews with the Nepalese land market stakeholders. These independently derived impact factors were compared with the desktop literature review impact factors resulting in fourteen land market impact factors across four dimensions, including transaction cost, valuation, mortgage availability, taxation, and compensation across the economic dimension; lot size, subdivision restrictions, and coordination across the institutional dimension; awareness, expectation and proximity across the social dimension; and risk reduction, quality of residential land, and suitability of zoning classification across the environmental dimension. There was significant overlap and commonality across factors identified from both the literature review and semi-structured interviews. The land market impact factors determined in the study may be adapted and generalized across other countries and could be utilized to better understand the impacts of land policy decisions on urban planning and development. Further research is recommended on the process to operationalize the use of these factors to quantify the impact of land use regulation on different land markets.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

‘‘Sustainable Supply Chain Management’’ (SSCM) has become a hot topic on which eminent researchers are working on every day. However, it is clear that we still observe in this field of research, an artistic vagueness on the fundamental differences between Sustainable Supply Chain Management and Green Supply Chain Management (GSCM) Moreover, it is regrettable to note that previous researchers haven't yet thought about having a specific theory which can be applied to SSCM, the use of macro theories still being observed. In addition, we observe a lack of research in the oil and gas industry especially in Developing Countries when we know that this industry is the most lucrative and polluting. Therefore, this paper’s purpose consists to make a Systematic Literature Review (SLR) of 38 papers published from 2005 to 2023 especially in oil and gas industry and in Developing Countries, in order to make a clear distinction between SSCM and GSCM while highlighting the practices related to them and at the same time, generating a united theory which will bring together the triple bottom line of the SSCM. As findings, the authors built a Conceptual Framework that applies the triple bottom line of the SSCM in oil and gas industry by demonstrating that GSCM which is more related to environmental issues and is a part of the SSCM. Therefore, in order to be more efficient and to have a great impact on their performances, Oil and gas companies should apply SSCM practices rather than GSCM practices which are very different from what is applied in Developed Countries because of certain barriers and pressures.

One of the most used markers of cancer stem cells in several cancers, including colorectal cancer and breast cancer, is CD44. CD44 is a glycoprotein that traverses the cell membrane and binds to many ligands including hyaluronan resulting in activation of signaling cascades. Several reports have shown conflicting data on the expression of CD44 and that the expression depends on modes of investigations and subtypes of cancers. In addition, the correlation between CD44 expression and drug resistance, immune infiltration, EMT, metastasis and patients prognosis in several cancer types remains unclear. This study investigated CD44 expression in several cancers and explored its relationship with tumorigenesis using various publicly available databases, including The Cancer Genome Atlas, GEPIA, Oncomine, Genomics of Drug Sensitivity in Cancer and Tumor Immune Estimation Resource. Our analysis reveals that CD44 is differentially expressed in different cancers. CD44 expression is significantly associated with cancer patients’ survival in gastric, pancreatic and colorectal cancers. In addition, CD44 expression is closely linked with immune infiltration and immune suppressive features in pancreatic, colon adenocarcinoma and stomach cancer. High CD44 expression was significantly correlated with the expression of drug resistance-, EMT- and metastasis- linked genes. Tumors expressing high CD44 have higher mutation burden and afflict older patients than tumors expressing low CD44. Cell lines expressing high CD44 are more resistant to anti-cancer drugs compared to those expressing low CD44. Protein-protein interaction investigations and functional enrichment analysis showed that CD44 interacts with gene products related to cell-substrate adhesion, migration, platelet activation, and cellular response to stress. KEGG pathway analysis revealed that these genes play key roles in biological adhesion, cell component organization, locomotion, G-α-signaling and the response to stimulus. Overall, this investigation reveals that CD44 play significant roles in tumorigenesis, can be used as a prognostic biomarker in several cancers and can be therapeutically targeted in cancer therapy.

Chloroquine was among the first of several effective drug treatments against malaria until the onset of chloroquine resistance. In light of diminished clinical efficacy of chloroquine as an antimalarial therapeutic, there is potential in efforts to adapt chloroquine for other clinical applications, such as in combination therapies and in diagnostics. In this context, we designed and synthesized a novel asymmetrical squaraine dye coupled with chloroquine (SQR1-CQ). In this study, SQR1-CQ was used to label live Plasmodium falciparum (P. falciparum) parasite cultures of varying sensitivities towards chloroquine. SQR1-CQ positively stained ring, mature trophozoite and schizont stages of both chloroquine–sensitive and chloroquine–resistant P. falciparum strains. In addition, SQR1-CQ exhibited significantly higher fluorescence, when compared to a chloroquine-BODIPY (borondipyrromethene) conjugate. We also achieved successful SQR1-CQ labelling of P. falciparum directly on thin blood smear preparations. Drug efficacy experiments measuring half-maximal inhibitory concentration (IC50) showed lower concentration of effective inhibition against resistant strain K1 by SQR1-CQ compared to conventional chloroquine. Taken together, the versatile and highly fluorescent labelling capability of SQR1-CQ and promising preliminary IC50 findings potentiates it to be further developed as a promising diagnostic bioimaging tool with drug efficacy against chloroquine-resistant P. falciparum.

Translation of basic animal research to find effective methods of diagnosing and treating human neurological disorders requires parallel analysis infrastructures. Small animals such as mice provide exploratory animal disease models. However, many interventions developed using small animal models fail to translate to human use due to physical or biological differences. Recently, large-animal minipigs have emerged in neuroscience due to both brain similarity and economic advantages. Medical image processing is a crucial part of research as it allows researchers to monitor their experiments and understand disease development. However, although many algorithms are created and optimized for MR analysis of human data, those tools are not directly applicable or sufficiently sensitive to measure minipig data. In this work, we propose PigSNIPE - a pipeline for the automated handling, processing, and analyzing of large-scale data sets of minipig MR images. The pipeline allows for image registration, AC-PC alignment, landmark detection, skull stripping, brainmasks and intracranial volume segmentation (DICE 0.98), tissue segmentation (DICE 0.82), and caudate-putamen brain segmentation (DICE 0.8) in under two minutes. To the best of our knowledge, this is the first automated pipeline tool aimed at large animal images.

In recent times, there has been significant enthusiasm for the development of all solid state batteries. This interest stems from a dual focus on safety—addressing concerns related to toxic and flammable organic liquid electrolytes—and the pursuit of high energy density. \cite{SCHNELL2018160,Zheng2018}. While liquid electrolyte batteries constitute for now the vast majority of commercial cells, solid electrolyte batteries show great promise. In parallel with experimental research, computational models \cite{GrazioliEtAlCM2016} clarify the several fundamental physics \cite{LiMonroeARCBM2020} that take place throughout battery operations. We review some classical models, emphasizing the conceptual advancements documented in the most recent works.

The possibility of using graphane monolayer crystals as the electrode material is becoming popular. Graphane is stable at room temperature and has large surface area, but its chemical inertness hinders its direct interactions with Li ions. In this study, we performed density functional theory calculations to study the energetic stability, structural and electronic properties of Li on graphane with various CH divacancy configurations (v12, v13 and v14 ). The results show that adsorption of Li atom reduces the formation energy of the CH divacancy configurations. The Li-v12 is most stable with the highest binding energy of 3.25 eV/Li and relaxes to in-plane with other C atoms. Altering the Li charge state to have Li−1-v12 or Li+1 -v12 affects the energetic stability and electronic characters of Li-v12 . The Li−1-v12 (Li +1-v 12 ) enhances (reduces) the binding force between Li and v 12 configuration, and furthermore it improves (deteriorates) the conductivity of the structure. Further investigation of graphane with vacancies is encouraged due to these intriguing observations, as it holds promise for potential utilization as an electrode material.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

In the present manuscript, we report new insights into the concept of (a)synchronicity in Diels-Alder (DA) reactions in the framework of the reaction force analysis, in conjunction with natural population calculations and atomic resolution of energy derivatives along the intrinsic reaction coordinate (IRC) path. Our findings suggest that the DA reaction transitions between a preferentially concerted mechanism to a stepwise one in a 0.10 Å window of synchronicity indices, ranging from 0.90 to 1.00 Å. We have also shown that the relative position of the global minimum of the reaction force constant with respect to the TS is an alternative and quantifiable indicator of the (a)synchronicity in DA reactions. Moreover, the atomic resolution of energy derivatives reveals that the mechanism of the DA reaction involves two inner elementary processes associated with the formation of each of the two C-C bonds. This resolution goes on to indicate that, in asynchronous reactions, the driving and retarding components of the reaction force are mostly due the fast and slow-forming C-C bonds (elementary process) respectively, while in synchronous ones both elementary processes retard and drive the process concomitantly and equivalently.

In the U.S. 44% of low-income households struggle to pay their utility bills, affecting their ability to afford necessities such as food and health expenses. Several government and utility funded energy efficiency programs exist to assist those experiencing energy insecurity. In Salt Lake City, Utah, there is a high demand for, but low availability of, energy efficiency services in underserved neighborhoods creating an opportunity for creative community-based programs to fill this inherent gap. This pilot project, involving the exchanging of LED bulbs in Salt Lake City, highlights the development of a community-based energy efficiency program that aims to bring energy savings to a uniquely targeted portion of the city and determines its feasibility in addressing energy insecurity at a larger scale. Through the 8-month project duration, 1,432 bulbs were exchanged at 23 events reaching 181 households in low-income areas. Through a year of use, these bulbs are estimated to save residents approximately 18,219 USD in electricity bills and reduce CO2 emissions from power plants by 122.23 metric tons, in addition to a savings of 4,400 USD in social cost of carbon as defined by the U.S. Environmental Protection Agency. Since this pilot reached less than 1% of households, we extrapolated a reach of 2%, 5%, and 7.5% and found substantial potential decreases in power plant emissions and financial savings. As this project is ongoing and being expanded, we discuss relevant findings that will help shape future community-based models so that they are appropriately deployed and more effective in alleviating local energy insecurity.

We present a modified version of the Szilard Engine, demonstrating that an explicit measurement procedure is entirely unnecessary for its operation. By considering our modified engine, we are able to provide a new interpretation of Landauer’s original argument for the cost of erasure. From this view, we demonstrate that a reset operation is strictly impossible in a dynamical system with only conservative forces. Then, we prove that to approach a reset yields an unavoidable instability at the reset point. Finally, we present an original proof of Landauer’s principle that is completely independent from the Second Law of Thermodynamics.

Tumorigenesis is a complex and dynamic process involving cell-cell and cell-extracellular matrix (ECM) interactions that allow tumor cell growth, drug resistance and metastasis. This review provides an updated summary of the role played by the tumor microenvironment (TME) components and hypoxia in tumorigenesis and highlight various ways through which tumor cells reprogram normal cells including into phenotypes that are pro-tumorigenic including cancer associated- fibroblasts, -macrophages and -endothelial cells. Tumor cells secrete numerous factors leading to transformation of a previously anti-tumorigenic environment into a pro-tumorigenic environment. Once formed, solid tumors continue to interact with various stromal cells including local and infiltrating fibroblasts, macrophages, mesenchymal stem cells, endothelial cells, pericytes, and secreted factors and the ECM within the tumor microenvironment (TME). The TME is key to tumorigenesis, drug response and treatment outcome. Importantly, stromal cells and secreted factors can initially be anti-tumorigenic but over time promote tumorigenesis and induce therapy resistance. To counter hypoxia, increased angiogenesis leads to formation of new vascular networks in order to actively promote and sustain tumor growth via supply of oxygen and nutrients whilst removing metabolic waste. Angiogenic vascular network formation aid in tumor cell metastatic dissemination. Successful tumor treatment and novel drug development require the identification and therapeutic targeting of pro-tumorigenic components of the TME including cancer-associated- fibroblasts (CAFs) and -macrophages (CAMs), hypoxia, blocking ECM-receptor interactions, in addition to targeting of tumor cells. Re-programming of stromal cells and the immune response to be anti-tumorigenic is key to therapeutic success. Lastly, this review highlights potential TME- and hypoxia-centred therapies under investigations.

Text fields in electronic medical records (EMR) contain information on important factors that influence health outcomes, however, they are underutilized in clinical decision making due to their unstructured nature. We analyzed 6,497 inpatient surgical cases with 719,308 free text notes from Le Bonheur Children’s Hospital EMR. We used a text mining approach on preoperative notes to obtain the text-based risk score algorithm as predictive of death within 30 days of surgery. We studied the additional performance obtained by including text-based risk score as a predictor of death along with other structured data based clinical risk factors. The C-statistic of a logistic regression model with 5-fold cross-validation significantly improved from 0.76 to 0.92 when text-based risk scores were included in addition to structured data. We conclude that preoperative free text notes in EMR include significant information that can predict adverse surgery outcomes.

Consumer preference not only dictates what food is consumed but how that food is produced. Ingredients in livestock feed that are not antibiotics, not genetically modified, not of animal origin, and that are nutrient-like, tend to be more acceptable to consumers, retailers, and producers. Mono- and diglycerides (MDG) fit these criteria, are commonly used in food, and are generally recognized as safe. But beyond being emulsifiers and a source of energy, MDG are also known to have antimicrobial, immune and microbiome modulation, and angiogenic activity. MDG in broiler diets have been shown to impact a variety of immune-related functions such as regulation of circulating antibodies, as well as decreased gene expression or protein concentration of pro-inflammatory cytokines like TNF-α, IL-1β, IL-6, and IFN-γ. In addition, MDG can affect metabolic function and intestinal integrity. Results of this review show that MDG can serve as antimicrobial and growth-supporting alternatives for reducing poultry production losses, improving resource utilization, and meeting consumer demand for sustainably produced and safe animal protein.

Fractional calculus gained a lot of attention in the last couple of years. Researchers discovered that processes in various fields follow rather fractional dynamics than ordinary integer-ordered dynamics, meaning the corresponding differential equations feature non-integer valued derivatives. There are several arguments for why this is the case, one of them being that fractional derivatives’ inherit spatiotemporal memory and/or the ability to express complex naturally occurring phenomena. Another popular topic nowadays is machine learning, i.e., learning behavior and patterns from historical data. In our ever-changing world with ever-increasing amounts of data, machine learning is a powerful tool for data analysis, problem-solving, modeling, and prediction. It further provides many insights and discoveries in various scientific disciplines. As these two modern-day topics provide a lot of potential for combined approaches to describe complex dynamics, this article reviews combined approaches of fractional derivatives and machine learning from the past, puts them into context, and thus provides a list of possible combined approaches and the corresponding techniques. Note, however, that this article does not deal with neural networks, as there already is profound literature on neural networks and fractional calculus. We sorted past combined approaches from the literature into three categories, i.e., preprocessing, machine learning & fractional dynamics, and optimization. The contributions of fractional derivatives to machine learning are manifold as they provide powerful preprocessing and feature augmentation techniques, can improve physically informed machine learning, and are capable of improving hyperparameter optimization. Thus, this article serves to motivate researchers dealing with data-based problems, to be specific machine learning practitioners, to adopt new tools and enhance their existing approaches.

The increasing spatial and spectral resolution of hyperspectral imagers yields detailed spectroscopy measurements from both space-based and airborne platforms. Machine learning algorithms have achieved state-of-the-art material classification performance on benchmark hyperspectral data sets; however, these techniques often do not consider varying atmospheric conditions experienced in a real-world detection scenario. To reduce the impact of atmospheric effects in the at-sensor signal, atmospheric compensation must be performed. Radiative Transfer (RT) modeling can generate high-fidelity atmospheric estimates at detailed spectral resolutions, but is often too time-consuming for real-time detection scenarios. This research utilizes machine learning methods to perform dimension reduction on the transmittance, upwelling radiance, and downwelling radiance (TUD) data to create high accuracy atmospheric estimates with lower computational cost than RT modeling. The utility of this approach is investigated using the instrument line shape for the Mako long-wave infrared hyperspectral sensor. This study employs physics-based metrics and loss functions to identify promising dimension reduction techniques. As a result, TUD vectors can be produced in real-time allowing for atmospheric compensation across diverse remote sensing scenarios.

As one of the critical state parameters of the battery management system, lithium battery state of charge (SOC) can provide an essential reference for battery safety management, charge/discharge control, and energy management of electric vehicles. To analyze the application of deep learning in electric vehicle power battery SOC estimation, this study reviewed the technical process, common public datasets, and the neural networks used, structural characteristics, advantages and disadvantages of lithium battery SOC estimation in deep learning method. First, the specific technical processes of the deep learning method for SOC estimation were analyzed, including data collection, data preprocessing, feature engineering, model training, and model evaluation. Secondly, the current commonly and publicly used lithium battery dataset was summarized. Then, the input variables, data sets, errors, and advantages and disadvantages of four types of deep learning methods, were concluded using the structure of neural network used for training as the classification criterion. Finally, the challenges and future development directions of lithium battery SOC estimation in deep learning method were explained.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

In this paper the application of recycled Li-ion batteries spent cathode (LIB-SC) combined with NaHCO₃/H₂O₂ system is presented for the first time in the literature as an alternative for degradation of potentially toxic organic molecules. The model pollutant choice was methylene blue molecule. The spent cathode composition corresponds to LiCoO₂, which was proved by the XRD and EDX. Regarding the decolorization of methylene blue solution, the addition of NaHCO₃ in comparison with only H₂O₂ reduces the complete decolorization time in 96%. This reduction occurs because the radical CO₃ is more stable than OH. In this way, the application the system proposed in this article is aimed at solving two major global problems: the disposal of cell phone batteries and the pollution of liquid effluents.

Crowdsourced Data (CSD) generated by citizens is becoming more popular as its potential utilisation in many applications is increasing due to its currency and availability. However, the quality of CSD, including its relevance, is often questioned as the data is not generated by professionals nor follows standard data collection procedures. The quality of CSD can be assessed according to a range of attributes including its relevance. Information relevance has been explored through using in Geographic Information Retrieval (GIR) techniques to identify relevant information. This research tested a relevance assessment approach for CSD by adapting relevance assessment techniques available in the GIR domain. The thematic and geographic relevance were assessed using the Term Frequency-Inverse Document Frequency (TF-IDF), Vector Space Model (VSM) and Natural Language Processing (NLP) techniques. The thematic and geographic specificities of the queries were calculated as 0.44 and 0.67 respectively, which indicates the queries used were more geographically specific than thematically specific. The Spearman's rho value of 0.62 indicated that the final ranked relevance lists showed reasonable agreement with a manually classified list and confirmed the potential of the approach for CSD relevance assessment for other possible crowdsourced data analysis.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

We provide quantitative results from GIS-based modelling of urban emission functions for a range of representative low- and mid-rise locations, ranging from individual streets to residential communities within cities as well as entire towns and city regions with the aim of whether lantern photometry or built environment has the dominant effect on light pollution. We demonstrate the scalability of our work by providing results for the largest urban area modelled to date, comprising the central 117 km2 area of Dublin City and containing nearly 42,000 public lights. Our results show a general similarity in the shape of the azimuthally-averaged emission function for all areas examined, with differences in total light output distribution depending primarily on the nature of the lighting and, to a smaller extent, on the obscuring environment including seasonal foliage effects. A comparison with global satellite observations shows that they are consistent with the deduced angular emission function for other low-rise areas worldwide. We further validate our approach by comparing results for a range of urban locations by the close agreement observed in a detailed comparison of with calibrated imagery from the International Space Station. To our knowledge, this is the first such detailed quantitative verification of light loss calculations.

We examine the relation between environmental, social, and governance commitment levels (ESG) and firm dividend payer status. Given that larger and more profitable firms are positively associated with both payer status and ESG, it could be that ESG and dividends are complements. However, given that both dividends and ESG relate to firm spending decisions, it may be that the choice is “either/or” and that ESG and dividends are substitutes. We document a positive relation between ESG and dividend payer status in U.S. firms over the period 1991-2016. In particular we find that the proportion of dividend payers is roughly 13% higher for firms with positive ESG compared to those with negative ESG. Including ESG in the models used to predict payer status provides, on average, a nearly 26% improvement in relative forecast accuracy. Our results are robust to estimation techniques and the inclusion of variables known to be determinants of payer status.

Climate warming is expected to have pronounced effects on Arctic and Subarctic ecosystems, especially regions underlain by discontinuous and relatively warm permafrost. The main goal of this research is to evaluate the vulnerability and dynamics of permafrost under climate warming across the various ecotypes in respect of ecosystem stability, socioeconomic impact, and for better understanding possible future environmental changes. We suggested the new version of the spatially distributed permafrost dynamics model (GIPL2-MPI), which is developed in the Geophysical Institute, University of Alaska Fairbanks. This model is based on the ecosystem approach to simulate the permafrost dynamics, which we are discussing in this paper. We combined ground-based observations and numerical freeze/thaw modeling using climate-ecosystem-permafrost interactions to understand the physical processes and mechanisms controlling permafrost physical state. We predict the changes in permafrost conditions using output from two GCMs (NCAR-CCSM4 and GFDL-CM3) and Five-Model Average Ensemble for the RCP-4.5 and RCP-8.5 scaled down to 1 by 1 km spatial resolution (https://uaf-snap.org/) across entire Alaska. Our result shows that by the end of the current century widespread near-surface permafrost degradation could begin everywhere in Alaska southward of the Brooks Range as well as across some spots at the North Slope Alaska.

This is an exercise to explore the concentration of Lithium, Lithium-7 isotope and the possible presence of black dirty ice in the lunar surface using spectral data obtained from the Clementine mission. The main interest in tracing the lithium and presence of dark ice in the lunar surface are closely related to future human settlement missions in the Moon. We investigate the distribution of Lithium and 7 Li isotope on the Lunar surface, employing spectral data from the Clementine images. We utilized Visible (VIS-NIR) imagery at wavelengths of 450, 750, 900, 950, and 1000 nm, along with Near-Infrared (NIR-SWIR) at 1100, 1250, 1500, 2000, 2600, and 2780 nm, encompassing 11 bands in total. This dataset offers a comprehensive coverage of about 80% of the lunar surface, with resolutions ranging from 100 to 500 meters, spanning latitudes from 80°S to 80°N. In order to extract quantitative abundance of Lithium, ground truth sites were used to calibrate the Clementine images. Samples (12045, 15058, 15475, 15555, 62255, 70035, 74220 and 75075) returned from Apollo missions 12, 15, 16 and 17 have been correlated to the Clementine VIS-NIR bands and five spectral ratios. The 5 spectral ratios calculated synthesize the main spectral features of sample spectra that were grouped by their Lithium and 7 Li content using Principal Component Analysis. The ratios spectrally characterize substrates of anorthosite, silica-rich basalts, olivine-rich basalts and High-T mare basalts and Orange soils. Our findings reveal a strong linear correlation between the spectral parameters and the lithium content in the 8 Apollo samples. With the values of the 11 Clementine bands and the 5 spectral ratios for each of the 8 lunar soils we performed linear regression models to estimate the concentration of Lithium and 7 Li. Also, we calculated Digital Terrain Models (DTMs; Altitude, Slope, Aspect, DirectInsolation and WindExposition) from LOLA-DTM to discover relations between relief and spatial distribution of the extended models of lithium and 7 Li. The analysis was conducted in a mask polygon extracted from Lunar Orbiter Laser Altimeter (LOLA) and located around the Apollo 15 landing site. This analysis seeks to uncover potential 7 Li enrichment through spallation processes, influenced by varying exposure to solar wind. To explore the possibility of find ice mixed with regolithe (black ice) we used a spectral library (350-2500nm) form ices dirty with different concentration of volcanic particles.

In the last two decades, the discovery of various pathways involved in renal cell carcinoma (RCC) have led to the development of biologically-driven targeted therapies. Hypoxia inducible factors (HIFs), angiogenic growth factors, von Hippel-Lindau (VHL) gene mutations and oncogenic miRNAs play essential roles in the pathogenesis and drug resistance of clear cell renal cell carcinoma. These insights have led to the development of VEGF inhibitors, mTOR inhibitors and immunotherapeutic agents which have significantly improved outcomes of patients with advanced RCC. HIF inhibitors will be a valuable asset in the growing therapeutic armamentarium of RCC. Various histone deacetylase (HDAC)inhibitors, including selenium and agents such as PT2385 and PT2977, are being explored in various clinical trials as potential HIF inhibitors to ameliorate the outcomes of RCC patients. In this article, we will review the current treatment options and highlight the potential role of selenium in the modulation of drug resistance biomarkers expressed in ccRCC tumors.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Metabolites present in the hemolymph of honey bees play a crucial role in modulating the metamorphic process within the species. However, the precise alterations in metabolite composition, along with the associated variances and regulatory pathways implicated during the larvae-to-pupae metamorphosis of honey bees, remain incompletely elucidated. In this investigation, we gathered hemolymph samples from honey bee larvae at three distinct physiological stages-feeding, prepupal, and pupae and subjected them to metabolite analysis utilizing the liquid chromatography-mass spectrometry (LC-MS) technique. Employing principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA), we identified significant differential metabolites and conducted a metabolic pathway analysis on those differentially up-regulated during the prepupal and pupae stages. Notably, metabolites up-regulated in the hemolymph of prepupal stage larvae primarily governed glucose metabolism and fat digestion and absorption, while those in pupae stage larvae were involved in regulating chitin and lipopolysaccharide precursor formation, as well as the biosynthesis of phenylalanine, tyrosine, and tryptophan. These findings bear significant implications for advancing our comprehension of the metamorphic processes in honey bees.

Background: The liver is involved in disseminated tuberculosis in more than 80% of the cases while primary liver involvement is rare, representing < 1% of all cases. Hepatic tuberculosis (TB) can be treated by conventional anti-TB therapy, however, diagnosing this disease still remains a challenge. The diagnosis might be particularly difficult in patients with a single liver lesion that could be misdiagnosed as a tumor or other focal liver lesions. While computed tomography and magnetic resonance imaging findings have been described, there is a paucity of literature on contrast-enhanced ultrasound (CEUS) features of hepatic TB. Case Summary: herein, we describe a case of a patient with tuberculous lymphadenopathy and chronic HCV-related liver disease who developed a single macronodular hepatic TB lesion. Due to the finding of a hepatocellular carcinoma (HCC) highly suggestive CEUS pattern, specifically a LR5 category according to the Liver Imaging Reporting and Data System (LI-RADS), and a good response to antitubercular therapy, a non-invasive diagnosis of HCC was made, and the patient underwent liver resection. We also review the published literature on imaging features of hepatic TB and discuss the diagnostic challenge represented by hepatic TB when occurs as a single focal liver lesion. Conclusions: this report shows for the first time that CEUS pattern of hepatic TB might be misinterpreted as HCC and specific imaging features are lacking. Personal history and epidemiological data are mandatory in interpreting CEUS findings of a focal liver lesion even when the imaging pattern is highly suggestive of HCC.

Dementia education and training for workforce development is becoming increasingly important in bridging knowledge gaps among health and social care practitioners in the UK and internationally. Dementia Education for Workforce Excellence (DEWE) was developed during the COVID-19 pandemic blending both synchronous and asynchronous instruction and delivered across three different contexts: care homes, home care, and nurse education within the UK and India. This study aimed to evaluate DEWE using mixed methods with online survey data analyzed descriptively and interview data analyzed thematically. Integration of survey and interview data aimed toward a comprehensive evaluation of this novel approach for dementia workforce development. Thirty-four social care practitioners and nurse educators completed the online survey demonstrating high-level learner satisfaction; learning gains; behavioral change, and motivation to share new knowledge. Four key themes developed from the analysis of interviews (n=9) around participants’ pursuit of new knowledge; delivery modes in DEWE; learning gains and impact of DEWE; and adaptations for future program implementation. Findings suggest DEWE is an innovative resource that promotes person- and relationship-centered dementia care across all stages of one’s dementia journey. Cultural adaptations are recommended for international delivery to ensure contextual alignment and maximum impact.

The terms 'open' and 'openness' are widely used across the current higher education environment particularly in the areas of repository services and scholarly communications. Open-access licensing and open-source licensing are two prevalent manifestations of open culture within higher education research environments. As theoretical ideals, open-licensing models aim at openness and academic freedom. But operating as they do within the context of global neoliberalism, to what extent are these models constructed by, sustained by, and co-opted by neoliberalism? In this paper, we interrogate the use of open-licensing within scholarly communications and within the larger societal context of neoliberalism. Through synthesis of various sources, we will examine how open access licensing models have been constrained by neoliberal or otherwise corporate agendas, how open access and open scholarship have been reframed within discourses of compliance, how open-source software models and software are co-opted by politico-economic forces, and how the language of 'openness' is widely misused in higher education and repository services circles to drive agendas that run counter to actually increasing openness. We will finish by suggesting ways to resist this trend and use open-licensing models to resist neoliberal agendas in open scholarship.

In the power plant industry, the turbine inlet temperature (TIT) plays a key role in the efficiency of the gas turbine and, therefore, the overall—in most cases combined—thermal power cycle efficiency. Gas turbine efficiency increases by increasing TIT. However, an increase of TIT would increase the turbine component temperature which can be critical (e.g., hot gas attack). Thermal barrier coatings (TBCs)—porous media coatings—can avoid this case and protect the surface of the turbine blade. This combination of TBC and film cooling produces a better cooling performance than conventional cooling processes. The effective thermal conductivity of this composite is highly important in design and other thermal/structural assessments. In this article, the effective thermal conductivity of a simplified model of TBC is evaluated. This work details a numerical study on the steady-state thermal response of two-phase porous media in two dimensions using personal finite element analysis (FEA) code. Specifically, the system response quantity (SRQ) under investigation is the dimensionless effective thermal conductivity of the domain. A thermally conductive matrix domain is modeled with a thermally conductive circular pore arranged in a uniform packing configuration. Both the pore size and the pore thermal conductivity are varied over a range of values to investigate the relative effects on the SRQ. In this investigation, an emphasis is placed on using code and solution verification techniques to evaluate the obtained results. The method of manufactured solutions (MMS) was used to perform code verification for the study, showing the FEA code to be second-order accurate. Solution verification was performed using the grid convergence index (GCI) approach with the global deviation uncertainty estimator on a series of five systematically refined meshes for each porosity and thermal conductivity model configuration. A comparison of the SRQs across all domain configurations is made, including uncertainty derived through the GCI analysis.

Objectives Asylum seekers in Germany represent a highly vulnerable group from a health perspective due to a variety of risk factors. At the same time their access to healthcare is restricted. While the introduction of the Electronic Health Insurance Card (EHIC) for asylum seekers instead of healthcare-vouchers is discussed controversially using politico-economic reasons, there is hardly any empirical evidence on its actual impact on the use of medical services Study design Thus, the aim of this study is to examine the influence of the possession of the EHIC on the use of medical services by asylum seekers as measured by their consultation rate of ambulant physicians (CR). For this purpose, a standardized survey was carried out to 260 asylum seekers in different municipalities of which some have introduced the EHIC for asylum seekers, while others have not. Methods Various CR were differentiated considering possible third variables as well as confounding factors. The period prevalence was compared between the groups "with EHIC" and "without EHIC" using a two-sided t-test. Multivariate analysis was done using a linear OLS regression model. Results Asylum seekers who are in possession of the EHIC are significantly more likely to seek ambulant medical care than those receiving healthcare-vouchers. Their CR, however, does not differ significantly from the age-corrected CR of the autochtonous population. Taking into account relevant covariables, the possession of the EHIC can be viewed as an independent influencing factor on the asylum seekers' use of medical care. Conclusions The results of this study suggest that having to ask for healthcare-vouchers at the social security office could be a relevant barrier for asylum seekers. Nevertheless, the ownership of the EHIC does not seem to lead to an overuse of medical services.

Tumor vasculature proliferates rapidly, generally lacks pericyte coverage, and is uniquely frag-ile making it an attractive therapeutic target. A subset of small-molecule tubulin binding agents cause disaggregation of the endothelial cytoskeleton leading to enhanced vascular permeability generating increased interstitial pressure. The resulting vascular collapse and ischemia cause downstream hypoxia, ultimately leading to cell death and necrosis. Thus, local damage gener-ates massive amplification and tumor destruction. The tumor vasculature is readily accessed and potentially a common target irrespective of disease site in the body. Development of a therapeutic approach and particularly next generation agents benefits from effective non-invasive assays. Imaging technologies offer varying degrees of sophistication and ease of implementation. This review considers technological strengths and weaknesses with examples from our own laboratory. Methods reveal vascular extent and patency, as well as insights into tissue viability, proliferation and necrosis. Spatiotemporal resolution ranges from cellular mi-croscopy to single slice tomography and full three-dimensional views of whole tumors and measurements can be sufficiently rapid to reveal acute changes or long-term outcomes. Since imaging is non-invasive, each tumor may serve as its own control making investigations par-ticularly efficient and rigorous. The concept of tumor vascular disruption was proposed over 30 years ago and it remains an active area of research.

Background: Co-infections of SARS-CoV-2 with respiratory viruses, bacteria and fungi have been reported to cause a wide range of illness. Objectives: We asses s the prevalence of co-infection of SARS-CoV-2 with seasonal respiratory viruses, document the respiratory viruses detected among individuals tested for SARS-CoV-2, and describe characteristics of individuals with respiratory virus co-infection detected. Methods: Specimens included in this study were submitted as part of routine clinical testing to Public Health Ontario Laboratory from individuals requiring testing for SARS-CoV-2 and/or seasonal respiratory viruses. Results: Co-infection was detected in a smaller proportion (2.5%) of individuals with laboratory confirmed SARS-CoV-2 than those with seasonal respiratory viruses (4.3%); this difference was not significant. Individuals with any respiratory virus co-infection were more likely to be younger than 65 years of age and male than those with single infection. Those with SARS-CoV-2 co-infection manifested mostly mild respiratory symptoms. Conclusions: Findings of this study may not support routine testing for seasonal respiratory viruses among all individuals tested for SARS-CoV-2, as they were rare during the study period nor associated with severe disease. However, testing for seasonal respiratory viruses should be performed in severely ill individuals, in which detection of other viruses may assist with patient management.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

This paper presents the concept of applying incremental capacity analysis (ICA) on the OCV curve in the SoC space. The OCV curve can be obtained from any sequence of discharge or charge current or power pulse with a necessary rest period to allow the cell to reach a pseudo-OCV after each pulse. With a higher resolution (>100 pulses) in the full SoC window, an OCV vs SoC curve can be obtained with sufficient accuracy to perform an ICA on the obtained OCV curve. ICA as a diagnostic technique has commonly been applied on Li-ion cells with a constant charge and discharge at slow currents. However, a slow controlled constant current charge or discharge is normally not feasible and cannot be easily applied to a battery in an application. Here we revisit pulse-based ICA to supplement the conventional constant-current-based technique. Conventional ICA performed on ageing data with constant current is directly compared to ICA performed on a selection of higher resolution OCV curves. The main advantage of OCV-ICA is that it can be applied to most cells and systems without significant interruption of normal cell operation. OCV-ICA provides valuable insights into ageing mechanisms as well as detailed information on changes in internal resistance.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

This code provides computational facilities to simulate current versus time during the charging of Li-ion cells at desire constant voltage by considering multiscale physical phenomena. This code only considers a powder of active materials (at microscale or nanoscale) and a small part of electrolyte around it as a half cell. Then it is extended to a complete cell by applying correct boundary conditions. This code is very useful by modifying code parameters to understand the effect of the complex shape of active materials powder (surface area and powder size), kind of electrolyte, and the applied voltages on the charging response of Li-ion cell. As a summary, a microscale approach to the design of Li-ion cells has been provided via this code.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

In this article, we investigate the applicability of quantum machine learning for classification tasks using two quantum classifiers from the Qiskit Python environment: the Variational Quantum Classifier (VQC) and the Quantum Kernel Estimator (QKE). We evaluate the performance of these classifiers on six widely known and publicly available benchmark datasets and analyze how their performance varies with the number of samples on two artificially generated test classification datasets. As quantum machine learning is based on unitary transformations, this paper explores data structures and application fields that could be particularly suitable for quantum advantages. Hereby, we developed a data set based on concepts from quantum mechanics using the exponential map of a Lie algebra. This dataset will be made publicly available and contributes a novel contribution to the empirical evaluation of quantum supremacy. We further compared the performance of VQC and QKE on six widely applicable datasets to contextualize our results.\\ Our results demonstrate that the VQC and QKE perform better than basic machine learning algorithms such as advanced linear regression models (Ridge and Lasso). They do not match the accuracy and runtime performance of sophisticated modern boosting classifiers like XGBoost, LightGBM, or CatBoost. Therefore, we conclude that while quantum machine learning algorithms have the potential to surpass classical machine learning methods in the future, especially when physical quantum infrastructure becomes widely available, they currently lag behind classical approaches. Our investigations also show that classical machine learning approaches have superior performance classifying datasets based on group structures, compared to quantum approaches that particularly use unitary processes.\\ Furthermore, our findings highlight the significant impact of different quantum simulators, feature maps, and quantum circuits on the performance of the employed quantum estimators. This observation emphasizes the need for researchers to provide detailed explanations of their hyperparameter choices for quantum machine learning algorithms, as this aspect is currently overlooked in many studies within the field.\\ To facilitate further research in this area and ensure the transparency of our study, we have made the complete code available in a linked GitHub repository.

We developed a temporal population receptive field model to differentiate the functional and hemodynamic responses in the human LGN. The hemodynamic response of the human LGN is dominated by the richly vascularized hilum, a structure that serves as a point of entry for blood vessels entering the LGN and supplying the substrates of central vision. The location of the hilum along the ventral surface of the LGN and the resulting gradient in the amplitude of the hemodynamic response across the extent of the LGN has made it difficult to segment the human LGN into its more interesting magnocellular and parvocellular regions that represent two distinct visual processing streams. Here, we show that an intrinsic clustering of the LGN responses to a variety of visual input reveals the hilum, and further that this clustering is dominated by the amplitude of the hemodynamic response. We introduce a temporal population receptive field model that includes both a sustained and transient temporal impulse response. When we account for the hemodynamic amplitude, we demonstrate that this temporal response model is able to functionally segregate the residual responses according to their temporal properties.

This paper proposes an Integrated Fire Management (IFM) framework that can be used to support communities and resource managers in finding effective and efficient approaches to prevent damaging fires, as well as maintain desirable fire regimes in Kenya. Designing and implementing an IFM approach in Kenya calls for a systematic understanding of the various uses of fire and the underlying perceptions and traditional ecological knowledge of the local people. The here proposed IFM framework allows an evaluation of the risks posed by fires, while balancing them with their beneficial ecological and economic effects, and thus developing effective fire management approaches. A case study of the proposed IFM framework was conducted in Gathiuru Forest that is part of the larger Mt. Kenya Forest Ecosystem. Focus group discussions were held with key resource persons, primary and secondary data on socio-economic activities were studied, fire and weather records were analyzed and the current fire management plans were consulted. Questionnaires were used to assess how the IFM is implemented in the Gathiuru Forest Station. The results show that the proposed IFM framework is scalable and can be applied in places with fire-dependent ecosystems as well as in places with fire-sensitive ecosystems in Kenya. The effectiveness is dependent on the active participation, formulation and implementation of the IFM activities by the main stakeholder groups (Kenya Forest Service (KFS), Kenya Wildlife Service (KWS), and the Community Forest Associations (CFA)). The proposed IFM framework helps in implementing cost-effective approaches to prevent damaging fires and maintain desirable fire regimes in Kenya.

There are frequently interactions between active folds and major rivers (mean annual water discharges > 70 m³s^-1). The major river may incise across the fold, to produce a water gap across the fold, or a bevelling (or lateral planation) of the top of the fold. Alternatively, the major river may be defeated to produce a diversion of the river around the fold, with wind gaps forming across the fold in some cases, or ponding of the river behind the fold. Why a river incises or diverts is often unclear, though influential characteristics and processes have been identified. A new scheme for investigating fold-river interactions has been devised, involving a short description of the major river, climate, and structural geology, and 13 characteristics of river and fold geomorphology: 1) Channel width at location of fold axis, w, 2) Channel-belt width at location of fold axis, cbw, 3) Floodplain width at location of fold axis, fpw, 4) Channel sinuosity, Sc, 5) Braiding index, BI, 6) General river course direction, RCD, 7) Distance from fold core to location of river crossing, C-RC, 8) Distance from fold core to river basin margin, C-BM, 9) Width of geological structure at location of river crossing, Wgs, 10) Estimate of erosion resistance of surface sediments/rocks and deeper sediments/rocks in fold, ERs, ERd, 11) Channel water surface slope at location of fold axis, s, 12) Average channel migration rate, Rm, 13) Estimate of fold total uplift rate, TUR. The first 10 geomorphological characteristics should be readily determinable for nearly all major rivers using widely available satellite imagery and fine scale geological maps. The last 3 characteristics should be determinable for most major rivers where other data sources are available. This study demonstrates the methodology of this scheme, using the example of the major rivers Karun and Dez interacting with active folds in the foreland basin tectonic setting of lowland south-west Iran. For the rivers Karun and Dez (mean annual water discharges 575 m³s^-1 and 230 m³s^-1, respectively), it was found that geomorphological characteristics Nos. 2, 3 and 7 had statistically significant differences (p-value ≤ 0.05) between the categories of river incision across a fold and river diversion around a fold. For river incision, at the fold axis, channel-belt width was always < 2.7 km, and floodplain width was generally (80 % of cases) < 5.7 km; whereas for river diversion, at the projection of the fold axis, these two characteristics had a wide range of values. For river incision, the distance from the fold core to the location where the river channel crossed the fold axis, was generally (80 % of cases) ≤ 8.5 km; whereas for river diversion, this distance was always > 22 km. Since it is highly likely that different characteristics will be important for other major rivers interacting with other folds, it is recommended that this scheme is now used to investigate a variety of major rivers from across the globe. By comparing the same parameters for different major rivers, a better understanding of fold-river interactions should be achieved.

With advances in Building Information Modeling (BIM), Virtual Reality (VR) and Augmented Reality (AR) technologies have many potential applications in the Architecture, Engineering, and Construction (AEC) industry. However, the AEC industry, relative to other industries, has been slow in adopting AR/VR technologies, partly due to lack of feasibility studies examining the actual cost of implementation versus an increase in profit. The main objectives of this paper are to understand the industry trends in adopting AR/VR technologies and identifying gaps within the industry. The identified gaps can lead to opportunities for developing new tools and finding new use cases. To achieve these goals, two rounds of a survey at two different time periods (a year apart) were conducted. Responses from 158 industry experts and researchers were analyzed to assess the current state, growth, and saving opportunities for AR/VR technologies for the AEC industry. The findings demonstrate that older generations are significantly more confident about the future of AR/VR technologies and they see more benefits in AR/VR utilization. Furthermore, the research results indicate that Residential and commercial sectors have adopted these tools the most, compared to other sectors and institutional and transportation sectors had the highest growth from 2017 to 2018. Industry experts anticipated a solid growth in the use of AR/VR technologies in 5 to 10 years, with the highest expectations towards healthcare. Ultimately, the findings show a significant increase in AR/VR utilization in the AEC industry from 2017 to 2018.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

Data creation is often the only way for researchers to produce basic geospatial information for the pursuit of more complex tasks and procedures such as those that lead to the production of new data for studies concerning river basins, slope morphodynamics, applied geomorphology and geology, urban and territorial planning, detailed studies, for example, in architecture and civil engineering, among others. This exercise results from a reflection where specific data processing tasks executed in Google Sketchup (Pro version, 2018) can be used in a context of interoperability with Geographical Information Systems (GIS) software. The focus is based on the production of contour lines and Digital Elevation Models (DEM) using an innovative sequence of tasks and procedures in both environments (GS and GIS). It starts in Google Sketchup (GS) graphic interface, with the selection of a satellite image referring to the study area—which can be anywhere on Earth's surface; subsequent processing steps lead to the production of elevation data at the selected scale and equidistance. This new data must be exported to GIS software in vector formats such as Autodesk Design Web format—DWG or Autodesk Drawing Exchange format—DXF. In this essay the option for the use of GIS Open Source Software (gvSIG and QGIS) was made. Correcting the original SHP by removing “data noise” that resulted from DXF file conversion permits the author to create new clean vector data in SHP format and, at a later stage, generate DEM data. This means that new elevation data becomes available, using simple but intuitive and interoperable procedures and techniques which confgures a costless work flow.

In this study, a cholera infection model with the bilinear infection rate is developed by considering the perturbation of the infection rate by the mean-reverting process. First of all, we give the existence of a globally unique positive solution for a stochastic system at arbitrary initial value. On this basis, the sufficient condition for the model to have an ergodic stationary distribution is given by constructing proper Lyapunov functions and tight sets. This indicates in a biological sense the long-term persistence of cholera infection. Furthermore, after transforming the stochastic model to an relevant linearised system, an accurate expression for the probability density function of the stochastic model around a quasi-endemic equilibrium is derived. Subsequently, the sufficient condition to make the disease extinct is also derived. Eventually, the theoretical findings are shown by numerical simulations. Numerical simulations show that the impact of regression speed and fluctuation intensity on stochastic systems.

Cancer patients and their family caregivers experience various losses when patients become terminally ill, yet little is known about the grief experienced by patients and caregivers and factors that influence grief as patients approach death. Additionally, few, if any, studies have explored associations between advance care planning (ACP) and grief resolution among cancer patients and caregivers. To fill this knowledge gap, the current study examined changes in grief over time in patients and their family caregivers and whether changes in patient grief are associated with changes in caregiver grief. We also sought to determine how grief changed following completion of advance directives. The sample included advanced cancer patients and caregivers (n=98 dyads) from Coping with Cancer III, a federally funded, multi-site prospective longitudinal study of end-stage cancer care. Participants were interviewed at baseline and at follow-up roughly 2 months later. Results suggest synchrony, whereby changes in patient grief were associated with changes in caregiver grief. We also found that patients who completed a living will (LW) experienced increases in grief, while caregivers of patients who completed a do-not-resuscitate (DNR) order experienced reductions in grief, suggesting that ACP may prompt “grief work” in patients while promoting grief resolution in caregivers.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

This study aims to examine the cytotoxicity mechanisms of synthetic cathinone (bath salts) on rat primary cultured neurons and primary astroglial cells, and to assess their neurobehavioral effects on mice. We administered methylenedioxypyrovalerone (MDPV) to both rat primary cultured neurons and primary astroglial cells to assess cell injury. We also analyzed the effects of MDPV on these cell cultures using immunocytochemistry. We utilized western blotting to assess the breakdown of αII-spectrin and glial fibrillary acidic protein (GFAP) induced by MDPV. The western blotting experiment also included calpain and caspase inhibitors (SNJ1945 and Z-D-DCB, respectively) and pro-apoptotic and pro-necrotic agents (Staurosporine and calcium ionophore A23187, respectively). Lastly, we assessed MDPV’s effects on behavioral effects using rotarod, locomotor activity, elevated plus maze, Morris water maze, forced swimming, and open field tests. MDPV caused a dose-dependent release of LDH in both cerebrocortical neuron-astroglia mixed cultures and primary astroglial cultures. MDPV also caused neurite breakages and astroglial process retraction on immunocytochemistry. Lastly, MDPV induced αII-spectrin breakdown in western blotting experiments. Co-administration of calpain and caspase inhibitors reduced the degradation of αII-spectrin and GFAP. MDPV administration also increased anxiety-like behavior and locomotor activity in the mice. Synthetic cathinones, which share structural similarities with methamphetamine, also induce significant neurotoxic effects and neurobehavioral effects on rodent models. These neurotoxic effects are likely mediated by calpain and caspase-induced apoptosis and necrosis, while astroglial death is likely only due to calpain activation. Therefore, further research may focus on pharmacological interventions targeting these pathways to mitigate the cytotoxic impact of cathinones in humans.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Alphaviruses are positive-sense RNA arboviruses that are capable of causing severe disease in otherwise healthy individuals. There are many aspects of viral infection that determine pathogenesis and major efforts regarding the identification and characterization of virulence determinants have largely focused on the roles of the nonstructural and structural proteins. Nonetheless, the viral RNAs of the alphaviruses themselves play important roles in regard to virulence and pathogenesis. In particular, many sequences and secondary structures within the viral RNAs play an important part in the development of disease and may be considered important determinants of virulence. In this review article, we summarize the known RNA-based virulence traits and host:RNA interactions that influence alphaviral pathogenesis for each of the viral RNA species produced during infection. Overall, the viral RNAs produced during infection are important contributors to alphaviral pathogenesis and more research is needed to fully understand how each RNA species impacts the host response to infection as well as the development of disease.

NIRS uses the relative absorption of light at 850nm and 760nm, to determine skeletal muscle oxygen saturation. Previous studies have used the ratio of both signals to report muscle oxygen saturation. Purpose: To evaluate the different approaches used to represent muscle oxygen saturation, and to evaluate the pulsations of the O₂heme and Heme signal. Method: Twelve participants, ages 20-29years were tested on the forearm flexor muscles using continuous wave NIRS at rest. Measurements were taken during 2-3mins rest, during physiological calibration (5-minuts Ischemia) and during reperfusion. Results: There was a significant difference in pulse size between O₂heme and Heme signal at the three locations (p < 0.05). Resting oxygen saturation was 58.8+9.2%, 69.6+3.9%, and 89.2+6.9% when calibrated using O₂heme, TSI, and Heme, respectively. Conclusion: The difference in magnitude of O₂heme and Heme pulse with each heartbeat might suggest different anatomical locations of these signals, which propose calibrating with just one of the signals instead of the ratio of both. Calculations of physiological calibration must account for increased blood volume in the tissue, because of the changes in blood volume which appear to be primarily from the O₂heme signal. Resting oxygen levels calibrated with Heme agrees with theoretical oxygen saturation.

Zika virus (ZIKV), without a vaccine or no effective treatment approved as yet, have globally spread since the past century. The infection caused by ZIKV in humans has changed progressively from mild to subclinical in the last years, causing epidemics with greater infectivity, tropism towards new tissues, and other related symptoms as a product of various emergent ZIKV-host cell interactions. However, it is still unknown why or how the RNA genome structure impacts those interactions in differential evolutionary origin strains. Moreover, genomic comparison of ZIKV strains from the sequence-based phylogenetic analysis is well known, but differences from RNA structure comparisons are less known. Thus, in order to understand the RNA genome variability of lineages of various geographic distributions better, 412 complete genomes in a phylogenomic scanning were used for studying the conservation of structured RNAs. We found specific genomic regions, which highlight their patterns of conserved RNA structures at the level of inter-geographical comparisons. We have proposed these structures as candidates for further experimental validation to establish their potential role in vital functions of the viral cycle of ZIKV and their possible associations with the singularities of different outbreaks that occurred in specific geographic regions.

Glucocorticoid administration is a common clinical practice in attempt to decrease inflammation associated with, and improve resectability of, canine mast cell tumors (MCTs). However, the impact of neoadjuvant glucocorticoids on histological features and proliferation indices of canine MCTs is unknown. The objective of this study was to evaluate changes in tumor grade, mitotic count, Ki67, AgNOR, and AgNORxKi67 scores following short-course, anti-inflammatory neoadjuvant prednisone in canine patients with MCTs. This was a prospective, single-arm pilot study. Client-owned dogs with treatment-naïve, cytologically-confirmed MCTs were enrolled. Patients underwent an initial incisional biopsy followed by a 10-14 day course of anti-inflammatory prednisone, and surgical resection. All histological samples were randomized, masked, and evaluated by a single pathologist. Unstained paired pre- and post-treatment samples were submitted to a commercial laboratory for Ki67 and AgNOR immunohistochemical analysis. There were 11 dogs enrolled with 11 tumors. There were no statistical differences between the pre- and post-treatment histological parameters of mitotic index, Ki67, AgNOR, or Ki67xAgNOR. There were no clinically-significant alterations between pre-treatment and post-treatment in the assignment of tumor grades. A short-course of anti-inflammatory prednisone does not appear to alter the histological parameters that affect grade-determination, nor significantly alter the proliferation indices in canine MCTs.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

In this study, Li-Al-OH layered double hydroxide (LDH), which was prepared by solvent-free one-step mechanochemical reaction of LiOH and Al(OH)₃, was applied to remove boron from aqueous solution. Dry-grinding for 3 h at a rotational speed of 500 rpm, Li/Al molar 1/2 was the optimum condition to prepare highly crystalline of Li-Al LDH phase with no evident impure phases. Two milling products with Li/Al molar ratio at 1/2 and 2/2 were evaluated for boron adsorption. The results confirmed that Li/Al molar ratio 2/2 sample showed high boron adsorption capacity due to the physical adsorption of Li-Al-OH LDH and chemical synergism of phase gel Al(OH)₃. The adsorption isotherms, described by the Langmuir model, indicated maximum monolayer boron uptake capacity 45.45 mg/g, implying competitive adsorption capacity of the material in our experiment.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

South Africa possesses the largest anti-retroviral therapy (ART) program in the world but the path to this record was dramatic. There is scarce literature employing a comprehensive framework to explain this ART policy change and inform current policy making processes. This paper applies the Advocacy Coalition Framework (ACF) to analyse the interactions among diverse actors, institutions and networks that were associated with the ART policy change in South Africa. Post-apartheid, HIV/AIDS and AIDS-related mortality were serious public health problems. At the time, the discernible coalitions in the AIDS policy subsystem were the prescience coalition and AIDS dissidents. In view of the availability of compelling scientific evidence on the pathogenesis of HIV/AIDS, the clinical usefulness of ART, the availability of funding for national ART roll-out, strong global advocacy to reduce the cost of ART, all of these in an era when access to adequate HIV care was increasingly considered a human right, the environment to establish an appropriate ART policy for the country was conducive. However, AIDS dissidents dominated the policy agenda via their control over key institutions, the use of various dimensions of power, biasing evidence to inform policy, and promoting the activities of strong interest groups that were not in support of ART. National ART roll-out ultimately emerged as a political priority as a result of external shocks (on the ART policy subsystem) which disfavoured the dominant coalition. Failure to supplement this application of the ACF with key pubic policy concepts such as power dimensions, evidence use in policy, governance and emergence of global health networks would have led to suboptimal appraisal of the ART policy change and misinformation of current policy making processes.

Inflammation is an underlying problem for many disease states and has been implicated in iron deficiency (ID). This study aimed to determine whether iron status is improved by epigallocate-chin-3-gallate (EGCG) through reducing inflammation. Thirty-two male Sprague-Dawley rats were randomly divided into four groups (n = 8 each): positive controls, negative controls, lipo-polysaccharide (LPS, 0.5 mg/kg body weight), and LPS + EGCG (LPS plus 600 mg EGCG/kg diet). Iron status, hepcidin, C - reactive protein (CRP), serum amyloid A (SAA), and interleukin-6 (IL-6) were measured. There were no differences in treatment groups compared with control in CRP, hepcidin, and liver iron concentrations. Serum iron concentrations were significantly lower in the LPS (p=0.02) and the LPS+EGCG (p=0.01) than in the positive control group. Compared to the positive control group, spleen iron concentrations were significantly lower in the negative con-trol (p<0.001) but not with both LPS groups. SAA concentrations were significantly lower in LPS + EGCG group compared to LPS alone group. IL-6 concentrations were significantly higher in LPS+EGCG (p= 0.004) than in any of the three groups. EGCG reduced SAA concentrations but did not affect hepcidin or improve serum iron concentration or other iron markers.

The greatly diversified flowering plants (angiosperms) are the dominating and defining group in the current earth ecosystem. However, from which group by what way the flowers, especially their gynoecia (key characteristics of angiosperms), are derived have been the questions in botany unanswered over centuries. Such an embarrassing situation can be attributed to the lack of plants with partially enclosed ovules, which are supposed to be a post between gymnosperms and angi-osperms. Here we report a fossil plant that has an apparent coniferous vegetative and reproduc-tive morphologies but has a single seed partially wrapped by the subtending bract. Such a mor-phology suggests that the carpels in angiosperms may be equivalent to bracts enclosing their axil-lary seed(s). Such a non-traditional interpretation of the homology of angiosperm carpels is com-patible with various new progresses made in botany and is in line with Tomlinson’s recent hy-pothesis. Together with other fossil evidence reported recently, it appears that gynoecia in angio-sperms are derived in multiple ways.

(1) Background: Patella and achilles tendon injuries have become increasingly prevalent due to an increasingly active population. These injuries can cause significant dysfunction which is especially true for elite athletes. Standard B-Mode ultrasound has been useful in the diagnosis of these injuries, however, only to a limited extent. Shear wave elastography (SWE) can aid in evaluation by objectively measuring tissue stiffness. Prior studies have proven shear wave values can be used to evaluate tendon tissue noting differences in healthy versus pathologic tendons. One main limitation remains a lack of normative data for specific tendon tissues which we aim to address in this study; (2) Methods: A cross-sectional study of healthy volunteers aged 18-65 without lower extremity injury was evaluated using A Samsung RS85 Prestige ultrasound machine with a 14L-2 MHz transducer. Shear wave values were collected in a standardized manner for the patellar tendon at one location, as well as the achilles tendon at the midportion and insertional areas; (3) Results: Data for 54 healthy adult patellar and achilles tendons was collected bilaterally. The mean SWE average of the patellar tendon (P1-P3) for all subjects was 96.3 +/- 10.9 kPA. A higher BMI was correlated with a decrease in patella tendon kPA and the mean PT1 was higher for males compared to females (adjusted mean 96.4 kPA for males and 88.5 kPA for females, mean difference = 7.9 kPA; P = 0.009). The mean SWE average of the insertional Achilles (AT1-AT3) for all subjects was 101.7 +/-16.2 kPA and for the midportion achilles (MTP1-MTP5) was 145.6 +/- 18.8 kPA. There was a decrease in kPA for insertional Achilles measurements in those with a higher BMI, but this did not reach statistical significance (p=.12); (4) Conclusion: This study provides normative SWE values for the patella and achilles tendon using the Samsung RS85. These values can be used for comparison to pathological tissue by means of the same examination protocol to better understand tendon degeneration. Further studies are warranted as to how SWE can be applied to the diagnosis of tendinopathy, partial and full-thickness tears, and response to treatment.

Solid tumors display complex biology and most therapies including chemotherapy cannot prevent therapy resistance and relapse. Most therapeutics target cancer cells, but recent data suggest the presence of cancer stem cells as cells with self-renewal and tumorigenic abilities. Cancer stem cell markers have been suggested to have prognostic value and can be targeted during cancer treatment and in resistant disease. CSCs have been postulated to play significant contextual roles in tumor initiation, progression, therapy resistance and metastasis. CSCs have thus been targeted by new generation cancer drugs. The transcriptional expression of several CSC markers in different cancers was evaluated by searching publicly available The Cancer Genome Atlas (TCGA) and Gene Expression Profiling Interactive Analysis (GEPIA) databases. We report here new findings on expression and prognostic significance of CSC markers in several cancers by examining the expression of CSCs markers in tumor tissues versus the adjacent normal tissues. We found that CSC markers were mostly highly expressed various tumors such as colon, lung, pancreatic and esophageal cancers. No CSC marker is expressed in the same pattern in all cancers and individual CSC marker expression was not linked to patient survival. This analysis calls for continued research on CSCs and clinical evaluation of the CSC markers in relation to prognosis of cancers in large population samples. Novel cancer drugs ought to target CSCs, cancer cells and tumor microenvironment variations.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

Glaucoma poses a serious public health concern as it is the second leading cause of blindness after cataracts, while also being the leading cause of irreversible blindness worldwide. Glaucoma is more prevalent among Black, Latino, and Asian populations and it is essential to examine both racial and ethnic disparities that exist in treatment and prevention. As the number of people with glaucoma continues to grow, it is important to review aspects of this condition in order to better care for those affected. This article will review significant forms of glaucoma and what differentiates them in a diagnosis, treatment options, and recommendations on prevention and improving awareness