Hospital-acquired infections (HAIs) contribute to increased length of hospital stay, high mortality and higher health-care costs. Prevention and control of HAIs is a critical public health concern. We conducted a cross-sectional survey of 213 hospital health-care workers in Qassim, Saudi Arabia. We assessed Knowledge, Attitude and Practice (KAP) of standard infection control precautions using a structured questionnaire. Predictors of KAP were investigated using multivaraible logistic regression analyses and independent sample t tests. Prevalence of good (≥80% correct response) knowledge, attitude and practice were 67.6%, 61.5% and 73.2%, respectively. Predictors of good knowledge included age over 34 years (adjusted odds ratio: 30.5, p<0.001), and receiving training (13.3, p<0.001). Predictor of positive attitude was having >6 years of experience (5.5, p<0.001). While, the predictors of good practice were having >6 years of experience (2.9, p<0.01), previous exposure to HAIs (2.5, p<0.05) and training (3.5, p<0.01). However, being female (0.22, p<0.001) and older (>34 years) (0.34, p<0.01) were negatively associated with knowledge. Results indicate that older academic programs might not have adequately covered infection crontrol. Arranging training for HCWs might be useful in improving their knowledge of standard infection control precautions and is also expected to facilitate positive attitude and practice.

Pneumonia kills over two million children under-age of five every year. Oral amoxicillin was recommended by WHO as the first drug of choice for treatment of non-severe pneumonia. The study aimed to determine the clinical failure rate of amoxycillin for the treatment of childhood non-severe pneumonia at Primary Health Care Centers (PHCCs). A randomized controlled multicenter-trial study was conducted in Sana’a. IMCI strategy was used to enrollments the cases where randomly allocated to receive amoxicillin or co-trimoxazole orally for five days. Multivariate logistic regression was used for identified risk factors associated with clinical failure. A total of 254 children were enrolled, of whom 128 cases were treated with amoxicillin while 126 with co-trimoxazole. The clinical failure for amoxicillin was significantly more than co-trimoxazole (30% vs 10%) p value > 0.001. the most risk factor which significantly associated to amoxicillin failure were pre-infection in the last 6 months, while abnormal CBC and literate mothers were associated with clinical failure of co-trimoxazole (p value > 0.05). The use of co-trimoxazole as an alternative to amoxicillin for the treatment of non-severe pneumonia in the PHCCs and conducting further studies to determine the appropriate antibiotic as the first line of defense are recommended.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

Smart livestock farming leverages technology to boost production and meet food demand sustainably. This study delves into smart technologies in animal production, covering opportunities, challenges, and solutions. Smart agriculture employs modern technology to enhance efficiency, sustainability, and animal welfare in livestock farming. It includes remote monitoring, GPS-based animal care, robotic milking, smart health collars, predictive disease control, and other innovations to achieve these goals. While smart animal production holds great promise, it does face challenges related to cost, data management, and connectivity. To address these challenges, potential solutions include remote sensing, technology integration, and farmer education. Smart agriculture offers opportunities for increased efficiency, improved animal welfare, and enhanced environmental conservation. A well-planned approach is crucial to maximize the benefits of smart livestock production while ensuring its long-term sustainability. This study confirms the growing adoption of smart agriculture in livestock production, with the potential to support sustainable development goals and deliver benefits such as increased productivity and resource efficiency. To fully realize these benefits and ensure the sustainability of livestock farming, it is essential to address cost and education challenges. Therefore, this study recommends promoting a positive outlook among livestock stakeholders and embracing smart agriculture to enhance farm performance.

Seawater contamination is a global challenge due to its hazardous effects on marine organisms and human health. Twenty-three surface seawater samples were collected from Al Lith intertidal area along the Saudi Red Sea coast to evaluate the ecological risks and document the potential sources of Cr, Cd, Fe, Zn, and Pb. Contamination factor (CF), contamination degree (Cd), water quality index (WQI), and heavy metal pollution index (HPI), as well as multivariate tools were applied. The averages of HMs (μg/L) had the following order: Zn (6.616) &gt; Pb (0.284) &gt; Cd and Cr (0.268) &gt; Fe (0.197). Results of CF showed moderate contamination of seawater with Cd and low contamination for Cr, Fe, Zn, and Pb. However, 26.09% of the samples showed considerable contamination for Cd. Average Cd values revealed low contamination for HMs, while 17.39% of the samples showed moderate contamination. HPI average values indicated medium pollution for Al Lith seawater, meanwhile 13 samples reported high pollution. The higher HPI values were reported in samples characterized by higher concentration of HMs, particularly Cd and Zn. Correlation matrix and principal component analysis suggested anthropogenic sources for Pb and Zn, mostly from industrial and agricultural effluents, landfilling and domestic wastewaters, apart from their natural sources.

Aim: This study measures and evaluates the socioeconomic burden of people living with keratoconus in Saudi Arabia. Methods: The study employed a cross-sectional design, a Keratoconus Economic Burden Questionnaire, and a convenient sample of 89 keratoconus patients (58.4% male) drawn from multiple regions in Saudi Arabia. It was conducted using online surveys and the data was analysed using appropriate quantitative techniques. Results: The mean age and annual income of participants were 33.24 years and Saudi Riyal (SAR) 33,505.6180 (SD=62,215.29), respectively, with only 37% being employed for wages. Up to 94.4% needed glasses or contact lenses at least once a week and 73.0% received care from optometrists. The condition forced 45.9% of the respondents to change careers or leisure activities, with a further 51.3% having to take time off work. The mean annual out-of-pocket expenses for buying and maintaining glasses or contact lenses as well as traveling and accommodation for keratoconus-related treatment were SAR 8,673.19 (SD=11,307.73), with 48.32 incurring upwards of SAR 12,000 over the period. The treatment costs increased with disease duration, r(89) = .216, p < .05. Regression results show that the existence of comorbid eye disease, changing glasses at least once a year, and wearing either glasses or contact lenses at least once a week individually have statistically significant, negative effects on the total annual keratoconus treatment costs, while disease duration, utilisation of optometrists, and taking time off had a statistically significant increase on the total cost (p<.05). Conclusion: With a prevalence rate of 1 in 375, progressive debilitation, and the lifetime nature of the disease, keratoconus is a critical public health concern in Saudi Arabia. The resulting visual impairment and discomfort as well as both direct and indirect economic burdens have considerable impacts on the patient's quality of life.

Over the past decade, Deep Learning (DL) had been applied in a large number of optical sensors’ applications. DL algorithms can improve the accuracy and reduce the noise level in optical sensors. Optical sensors are considered as promise technology for the modern intelligent sensing platforms. These sensors are widely used to process monitoring, quality prediction, pollution, defense, security and many other applications. However, they suffer major challenges such as the large generated data and low processing speed for that data and moreover the much cost of these sensor. These challenges can be mitigated by integrating deep learning system with the optical sensor technologies. This paper presents recent studies that integrate DL algorithms with optical sensors applications. This paper also highlights several of DL algorithms directions that promise a considerable impact on use for optical sensor applications. Moreover, this study provides new directions for the future related research development.

: Plant-derived terpenes have aroused considerable interest as chemotherapeutic agents for a variety of diseases. This study aimed at the isolation and purification of the scarce terpenes psiadin, plectranthone and saudinolide from their respective plants, followed by the determination of antiproliferative activity, against hepatic cancer cell lines (HepG2, Hep3B), and the potential molecular mechanisms. Time- and dose-dependent cytotoxicity, evaluated using MTT and colony-forming assays, were exhibited by psiadin and plectranthone against the cancer cells. Flow cytometry showed that these two terpenes blocked cell cycle progression and induced mitochondrial-mediated apoptosis, particularly through increased cytochrome c and disruption of mitochondrial membrane potential. Additionally, they initiated the generation of reactive oxygen species as well as inhibiting NF-B. Psiadin lowered several essential cyclins and cyclin-dependent kinases and reduced RB activation. It was concluded that psiadin, in particular, has a significant therapeutic potential with the biggest advantage of differentiating between cancer and normal cells which is acutely lacking in current cytotoxic drugs. Its precise mode of action needs further investigation but appears predominantly to cause cell cycle arrest by interfering with cyclin production. It will be important to determine, in future studies, whether these terpenes will similarly inhibit other cancer cell lines and retain its activity against tumors in vivo.

The proliferation of fake news on social media platforms poses significant challenges to information authenticity and public trust. In this study, the impact of various word embedding techniques on the performance of both machine learning and deep learning models for fake news detection is systematically evaluated. The comprehensive TruthSeeker dataset, which spans over a decade of labeled news articles and social media posts, is utilized. Three popular word embedding techniques are analyzed: TF-IDF, Word2Vec, and FastText. These embeddings were tested with multiple machine learning classifiers, including logistic regression, naive Bayes, K-nearest neighbors, support vector machines, multilayer perceptrons, decision trees, and random forests, as well as deep learning models, specifically convolutional neural networks (CNNs). Among machine learning models, the Support Vector Machine (SVM) with TF-IDF achieved the highest accuracy of 99.03%, precision of 98.92%, recall of 99.15%, and F1 score of 99.03%. The Multilayer Perceptron (MLP) also demonstrated strong performance with Word2Vec, reaching an accuracy of 95.24%, precision of 94.95%, recall of 95.50%, and F1 score of 95.07%. For deep learning models, CNNs combined with TF-IDF embeddings showed outstanding results, achieving an accuracy of 98.99%, precision of 98.56%, recall of 99.48%, and F1 score of 99.02%. These results highlight the critical role of word embeddings in enhancing model accuracy and reliability in misinformation detection.

To assess contamination levels, sources, and ecological health risks of potentially toxic elements (PTEs) in the sediments of Al Lith on the Saudi Red Sea coast, 25 samples were collected and analyzed for Zn, V, Cr, Cu, Ni, As, Pb, and Fe using ICP-AES. The average concentrations of PTEs (μg/g) were found in the following order: Fe (14259) > V (28.30) > Zn (22.74) > Cr (16.81) > Cu (12.41) > Ni (10.63) > As (2.66) > Pb (2.46). Contamination indices indicated that Al Lith sediments exhibited either no or minimal enrichment of PTEs, with concentrations below the low effects range. This suggests that the primary source of these PTEs is the basement rocks of the Arabian Shield and that they are unlikely to pose a substantial risk to benthic communities. The hazard index (HI) values for PTEs in both adults and children were below 1.0, indicating no significant non-carcinogenic risk. Lifetime cancer risk (LCR) values for Pb, As, and Cr in both adults and children were within acceptable or tolerable levels, posing no significant health threats. However, a few samples showed LCR values exceeding 1 × 10-4, indicating potential risks.

The leaves of Nicotiana glauca (Solanaceae) plant, are known for its major cause of health concern. This study investigated the antioxidant activity and polyphenols composition of aerial parts of N.glauca collected from its wild habitat in Jordan, using Methanol-Conventional (MC) and deep eutectic solvents (DESs) extraction methods in addition to nicotine content determination using UHPLC. The results have shown that the MC extract contains fewer total phenols and flavonoid content than the DES extract at ratio of 90% (0.1194 ±0.009 and 0.311± 0.020 mg/mL equivalent to gallic acid) and (0.01084±0.005 and 0.928 ± 0.09 mg/mL equivalent to rutin), respectively. Moreover, the study showed that the MC extract contains 635.07 ppm nicotine compared to the DES extraction method, which contains 1194.91 ppm. Both the MC and the DES extracts exhibited weak antioxidant activities with the highest was 33%inhibition equivalent to ascorbic acid was found for DES at (90%) ratio. The UHPLC-MS/MS analysis revealed the presence of variations in the detected compounds between the two extraction methods used. This study found that en-vironmentally friendly DES extraction of N. glauca produced higher phenol and flavonoid content than MC method, highlighting green chemistry methods' superior efficiency and environmental benefits for extracting valuable phytoconstituents.

The transition to sustainability requires major behavioural changes. This requires a complete rethinking of ecosystems and their interconnections, reassessing environmental issues, and a behavior change manifesting. Thus, understanding how sustainability Knowledge, Attitudes, and Practices (KAP) change is essential to sustainability as they shape human behaviour. The main aim of this study was to investigate the constructs of sustainability KAP among university and non-university populations. Data were collected using a structured questionnaire of items measured on a five-point Likert scale ranging from 1 (strongly disagree) to 5 (strongly agree). The questionnaire was distributed to diverse participants, ensuring a broad representation of views on sustainability. There are ten sociodemographic variables, 344 respondents in UAE where the female (28.5%) and male (13.7%), (58.1%) participants did not belong to the UAE university and their age fall into the 18-24 years old. The mean scores indicate a positive orientation towards sustainability, with Knowledge (M = 4.2272), Attitudes (M = 4.2650), and Practices (M = 3.8198) all above the midpoint and the UAE university students showed more knowledge, attitude and practices scores ‎than others population. Associations between KAP were significant at a significant level of p &lt; 0.05. This indicates that the next generation will have more environmentally KAP.

The Ministry of Health (MOH) in the Kingdom of Saudi Arabia (KSA) established a National School-based Screening Program (NSBSP) for health screening of school-going children. Students from specific grades were systematically screened for several health problems including obesity, visual and auditory problems, dental cavities, scoliosis, and attention-deficit/hyperactivity disorder (ADHD). This cross-sectional study aimed to determine the prevalence of these health problems among primary school students based on secondary data obtained from the NSBSP. We included 444,259 screened school children from the 1st and 4th grades of 50% of the selected schools (both private and public) across the KSA during the academic year 2018-2019. Among them, the most prevalent health problems identified were dental cavities (38.7%), eye refractory errors (10.9%), and overweight and obesity (10.5%); the less prevalent problems included ADHD (2.81%), auditory problems (0.6%), and scoliosis (0.48%). A greater prevalence of most health problems was observed in girls than boys. The NSBSP successfully aided the detection of health conditions with high and low prevalence among primary school students in the KSA, and thus, identification of health problems of specific concern. Implementation of effective school health services for the prevention, early detection, diagnosis, and treatment of these health problems is imperative.

The transition to sustainable energy systems in the Middle East and North Africa (MENA) region addresses critical challenges of environmental protection, energy security, and socio-economic resilience. Using neo-institutional theory, this paper examines the intricate relationship between formal and informal institutions and their significant impact on the region’s energy transition. Despite the MENA region’s abundant renewable energy resources, numerous institutional barriers, such as governance inefficiencies, regulatory inconsistencies, and entrenched socio-cultural norms, significantly hinder this transition. Through a review of existing literature, this study presents a comprehensive analytical framework designed to overcome these barriers, with a focus on the Just and Sustainable Energy Transition model. This strategic model emphasizes equity, sustainability, and inclusive governance as pillars for reform. The study offers detailed recommendations for institutional change and underscores the importance of collaborative efforts among governments, industry stakeholders, and international partners to unlock the MENA region’s renewable energy potential, advance global sustainability goals, and ensure a more secure and resilient energy future.

The increasing cancer burden is a major health concern in Arab countries with variations in cancer profiles. Given the limited oncology research output and scarce data on cancer trial participation in the Arab region, this study explored the therapeutic cancer trial landscape in Arab countries over the past 20 years. A bibliometric analysis of the PubMed database was conducted on primary publications of therapeutic trials with a participating Arab center. Arab countries participated in 320 published cancer-related therapeutic trials (2000‒2021). There was a consistent increase in the number of trials, sample size, multiregional site participation, and number of randomized trials. However, most trials were small, did not receive external funding, and included a single Arab site. Compared with Arab-only trials, trials with joint non-Arab sites were larger (p = .003) and more likely to be externally funded (p < .001). Citation numbers and journal impact factors were higher in trial publications with joint non-Arab authorship than those without (p < .001, for both). Despite improving conduct and publication records of oncology trials with Arab centers, cancer trial participation remains limited in Arab countries. Concerted efforts are required to encourage sponsorship and international collaboration in this region.

Many corner detector techniques have already been used in extracting information from UAV images to perform various photogrammetric and mapping activities. Among these techniques is the Feature from Accelerated Segment Test (FAST) and the Harris corner detector. It is widely agreed that the evaluation of detectors is of great importance because it evaluates and enhances the accuracy of the detected features. This research evaluates the performance of FAST-9 and FAST-12 as well as the Harris detector in terms of the repeatability rate, completeness, and correctness under different threshold values. Each method is evaluated in terms of its ability for detection UAV objects (crowd and cars features). Then the common detected features between both FAST versions and the Harris detector are extracted. This is to determine which method performs best under different image conditions (e.g., illumination variations, camera position and orientation, and image noise). The results show that the size of the threshold plays a crucial role in determining the number of detected feature points. An increase in the threshold value leads to a decrease in the number of detected points and vice versa. Thus, the correctness decreases whereas the completeness increases as a function of the threshold values. Furthermore, the relationship between the FAST-9 and the Harris detector is slightly better than those between the FAST-12 and the Harris detector. This is because the number of common features between the FAST-9 and the Harris detector are relatively higher than those between the FAST-12 and the Harris detector.

This study finds that in northern Jordan, breeder indicators present challenges to the sustainability and growth of sheep and goat farming, while economic indicators suggest a combination of financial stability alongside hurdles related to profitability and resource ownership. Breeder age plays a role in the management of livestock herds, due to factors such as experience, resources, or adherence to traditional practices. Experience significantly affects breeders' decisions on male insemination replacements, likely due to skill. Crop cultivation influences breeders' returns by reducing feeding costs, while strategic lamb sales management boosts individual animal profitability. Winter raises animal mortality due to cold stress. Other animals in herds increase kid mortality by spreading diseases. Breeder experience significantly affects lamb survival, stressing its role in care. Increasing sheep proportion enhances lamb production and reduces lamb mortality while managing rams and selling lambs positively affects herd health and productivity. A larger goat herd proportion positively correlates with kids sold but inversely with breeding males and overall kids, implying trade-offs affecting herd productivity and mortality rates. Sheep herds (92.5%) show slightly better reproductive success than goats (90.6%), implying superior long-term viability. Flock excels in birth, survival, and sales, but low sheep and lamb%. Improvement is needed for sustainability, and the potential is high. Goat breeding shines in birth, sales, and overall success, but needs attention to kid survival and other sustainability issues. In conclusion, despite challenges, there are promising opportunities to enhance sheep and goat farming in Jordan. Effective management, informed by breeders' experience and economics, is crucial. Empowering small-scale herders and implementing targeted interventions like winter mortality solutions and selective breeding is vital for sustainable growth.

this paper focuses on a scientific study of the restoration, rehabilitation and reuse of the great throne hall, the most important hall in al-jawhara palace. it also aims to study the most important factors and forces of damage that affected the great throne hall, natural, biological, and human, and the resulting damage. field tests were performed, laboratory tests to determine fracture stress, liquidity and spandex limits tests, chemical analysis on soil samples and geoelectrical testing of the soil, and the results did not show caves or voids in the ground until a depth of 10.00 m, construc-tion materials were studied and tested using x-ray, (xrd), mechanical tests (tensile, shear, com-pression), and a study of the effect of seismic loads on the walls; the results showed horizontal and vertical cracks; based on the study and analysis of these cracks, it was possible to present modern techniques in restoration and reinforcement methods, and in conclusion, the researcher's recommendations.

Purpose: When it comes to improving citizen service delivery standard and processes, or broadly, management in government (MIG), many reform programs and improvement efforts are ongoing across different ministries, departments, and agencies. This paper is part of a larger empirical research where we are interested to know what those programs and projects are, and how they are doing, and what the gaps are. Design/methodology/approach: Analyzing the publicly available data on the government portal and donors’ website, this article provides an overall idea of current reforms in various places of government. In parallel, field research was conducted through visiting agency offices, observing office environment and mechanisms, and interviewing public managers who are working at district and sub-district level offices of directorates or agencies.Findings: As a trend, state-led development process and the traditional mode of administration have moved to New Public Management based quality and performance approach. All donors have their own strategy framework document like ‘Country Assistance strategy’, ‘Country Operations and Business Plan’, Logical Framework Document, Focus or Priority Streams, etc. Many of the projects are sectoral and agency or ministry specific and have an inherent limitations, due to ‘cadre’ based organizational structural arrangement. So, it is common ‘not to own the projects’, rather ‘using the fund as much as possible anyway within the given project duration’. When the fund ends, implementing units, either government or NGOs, abandon the projects. That is why many projects are actually half done without significant and sustained direction.Originality/value: We can conclude that the typical ‘top-down’ or ‘trickle down’ conception is still dominant in design and implementation of reforms programs and service quality efforts. So, how to reach systemically at the bottom where public managers provide services to citizens, needs even more deliberation.

We study the brain segmentation by dividing the brain into multiple tissues. Given possible brain segmentation by deep, machine learning can be efficiently exploited to expedite the segmentation process in the clinical practice. To accomplish segmentation process, a MRI and tissues transfer using generative adversarial networks is proposed. Given the better result, we propose the transfer model using GAN. For the case of the brain tissues, white matter (WM), gray matter (GM) and cerebrospinal fluid (CSF) are segmented. Empirical results show that this proposed model significantly improved segmentation results compared to the stat-of-the-art results. Furthermore, a dice coefficient (DC) metric is used to evaluate the model performance.

The rodents of Saudi Arabia consist of 20 species and 12 genera within four families (Gliridae, Dipodidae, Muridae, and Hystricidae). Details on the past and present distribution of the rodents were included along with available data on their habitat preference and biology. The eastern central part of Saudi Arabia covering Tuwiq mountains plateau, including the vicinity of Riyadh, hosts the highest number of rodent species. Analysis of the rodent fauna of Saudi Arabia revealed that they have four major zoogeographical affinities; Palaearctic-Oriental (one species), Afrotropical- Palaearctic (six species), Palaearctic (four species), endemic to Saudi Arabia and Yemen (three species), Afrotropical-Palaearctic-Oriental (three species) and three cosmopolitan species. According to the National Red List, the Euphrates Jerboa, S. euphratica, is listed as Endangered, Near Threatened for the Indian Crested Porcupine, H. indica, three species as Data Deficient, while the rest are considered as Least Concern.

This hypothesis demonstrates that the efficiency of Loop-Mediated Isothermal Amplification (LAMP) for nucleic acid detection can be positively influenced by preconcentration of microbial cells onto hydrophobic paper surfaces. The mechanism of this model is based on the high attraction of microbes towards hydrophobic surfaces. Extensive studies have demonstrated that hydrophobic surfaces exhibit enhanced bacterial and fungal adhesion. The preconcentration approach by exploiting this inherent affinity of hydrophobic paper substrates enables the adherence of a greater number of target cells, resulting in a higher concentration of target templates for amplification directly from urine samples. In contrast to conventional methods, which often involve complex procedures, this approach offers a simpler, cost-effective, and user-friendly alternative. Moreover, the integration of cell adhesion, LAMP amplification, and signal readout within paper origami-based devices can provide a portable, robust, and highly efficient platform for rapid nucleic acid detection. This innovative hypothesis holds significant potential for point-of-care (POC) diagnostics and field surveillance applications. Further research and development in this field will advance the implementation of this technology, contributing to improved healthcare systems and public health outcomes.

Ti-Al based alloys, particularly TiAl and Ti3Al two-phase alloys, have garnered significant attention as potential replacements for various high-temperature structural materials due to their exceptional properties, including low density, oxidation resistance, and high strength at elevated temperatures. Despite these advantages, experimental studies on the microstructure evolution of Ti-Al based alloys under complex conditions remain challenging to observe and characterize. This review article examines the current research on molecular dynamics (MD) simulations of Ti-Al based alloys, focusing on two-phase Ti-Al alloys, Ti-Al amorphous alloys, Ti-Al composite materials, and the welding and multi-layer/film applications of Ti-Al alloys. The review highlights the unique capabilities of MD simulations in predicting the behavior of Ti-Al based alloys and addresses existing scientific challenges. Furthermore, the article discusses future research directions and development prospects in this field.

Segmentation is an important step in medical imaging. In particular, machine learning, especially deep learning, has been widely used to efficiently improve and speed up the segmentation process in clinical practice. Despite the acceptable segmentation results of multi-stage models, little attention was paid to the use of deep learning algorithms for brain image segmentation, which could be due to the lack of training data. Therefore, in this paper, we propose a Generative Adversarial Network (GAN) model that performs transfer learning to segment MRI brain images.Our model enables the generation of more labeled brain images from existing labeled and unlabeled images. Our segmentation targets brain tissue images, including white matter (WM), gray matter (GM), and cerebrospinal fluid (CSF). We evaluate the performance of our GAN model using a commonly used evaluation metric, which is Dice Coefficient (DC). Our experimental results reveal that our proposed model significantly improves segmentation results compared to the standard GAN model. We observe that our model is 2.1–10.83 minutes faster than stat-of-the-art-models.

A relevant aspect in the epidemiology of Tegumentary Leishmaniasis (TL) is the Leishmania parasites carrying a viral endosymbiont Leishmania RNA Virus 1 (LRV1), a dsRNA virus. Leishmania parasites carrying LRV1 are prone to causing more severe TL symptoms, increasing the likelihood of unfavorable clinical outcomes. LRV1 has been observed in cultured strains of five L. (Viannia) species, and host specificity was suggested when studying LRV1 from L. braziliensis and L. guyanensis strains. The coevolution hypothesis of LRV1 and Leishmania was based on phylogenetic analyses, implying an association between LRV1 genotypes, Leishmania species, and their geographic origins. This study aimed to investigate LRV1 specificity to Leishmania (Viannia) species hosts by analyzing LRV1 from L. (Viannia) species. To this end, LRV1 was screened in L. (Viannia) species other than L. braziliensis or L. guyanensis, and it was detected in 11 out of 15 L. naiffi and in 2 out of 4 L. shawi. Phylogenetic analyses based on partial LRV1 genomic sequencing supported the hypothesis of host specificity, as LRV1 clustered according to their respective Leishmania species hosts. These findings underscore the importance of investigating Leishmania and LRV1 coevolution and its impact on Leishmania (Viannia) species dispersion and pathogenesis in the American Continent.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

This is a case study in the domain of public sector management or management in government, with particular reference to education as a sector as a whole. Bangladesh has shown persistent upward trends in development indicators during the last four decades. In the education sector also, many indicators improved - literacy, the female proportion of literacy, number of educational institutions, etc. Quantity wise investment and indicators increased and improved at all levels and dimensions like primary, secondary, tertiary, technical, and so on. But qualitative improvement remained mysteriously low, despite government intention to increase quality of teaching, learning, and administration. This paper aimed to draw an overall picture of qualitative scenario of the education sector. Analyzing secondary sources like public media, and primary sources like citizen interactions, this qualitative study consolidated the problems of the education sector in a coherent whole. It argues that many problems of education sector are not education problems or budget problems, rather purely and simply ‘management’ problems, and so, can effectively be solved with basic but thorough understanding of the basic technicalities of management as a discipline.

This paper deals with experimental study of the influence of conductive (Fe₃O₄) and insulating (Al₂O₃) nanostructured particles at various concentrations on the dielectric strength of transformer mineral oil. The method of preparation and characterization of these nanofluids (NFs) through the measurements of zeta potential, the real and imaginary parts of dielectric constant as well as the concentration and size of nanoparticles using Scanning Electron Microscope (SEM) images of nanoparticles powders and Dispersive x-ray Spectroscopy (EDS) analysis are presented. Experimental findings reveal that these two types of nanoparticles materials significantly improve AC breakdown voltage and the magnitude of this improvement depends on the concentration, size and nature (material) of nanoparticles. For a given type of nanoparticles, the effect is more marked with the smallest nanoparticles. The conductive nanoparticles offer higher enhancement of dielectric strength compared with insulating nanoparticles based nanofluids. With Fe₃O₄, the breakdown voltage (BDV) can exceed twice that of mineral oil and it increases by more than 76% with Al₂O₃. The physicochemical mechanisms implicated in this improvement are discussed.

Survivability is a critical concern in WSNs, heavily influenced by energy efficiency. Addressing severe energy constraints in WSNs requires solutions that meet application goals while prolonging network life. This paper presents an energy optimization approach (EOAMRCL) for WSNs, integrating the Grey Wolf Optimization (GWO) for enhanced performance. EOAMRCL aims to enhance energy efficiency by selecting the optimal duty-cycle schedule, transmission power, and routing paths. The proposed approach employs a centralized strategy using a hierarchical network architecture. During the cluster formation phase, an objective function, augmented with GWO, determines the ideal cluster heads (CHs). The routing protocol then selects routes with minimal energy consumption for data transmission to CHs, using transmission power as a metric. In the transmission phase, the MAC layer forms a duty-cycle schedule based on cross-layer routing information, enabling nodes to switch between active and sleep modes according to their network allocation vectors (NAV). This process is further optimized by an enhanced CSMA/CA mechanism, which incorporates sleep/activate modes and pairing nodes to alternate between active and sleep states. This integration reduces collisions, improves channel assessment accuracy, and lowers energy consumption, thereby enhancing overall network performance. EOAMRCL was evaluated in a MATLAB environment, demonstrating superior performance compared to EEUC, DWEHC, and CGA-GWO protocols, particularly in terms of network lifetime and energy consumption. This highlights the effectiveness of integrating GWO and the updated CSMA/CA mechanism in achieving optimal energy efficiency and network performance.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

Preventive Maintenance (PM) is a periodic maintenance strategy, which has great results for devices in extending their life, increasing productivity, and most importantly, help avoid unexpected breakdowns and their costly consequence. A preventive maintenance scheduling (PMS) is determining the time for carrying out PM, and it represents a sensitive issue in terms of impact on production if the time for the PM process is not optimally distributed. In this study, hybrid heuristic methods were used to solve the PMS problem, as genetic algorithm and Tabu research were adopted. The optimal solution was reached in a short time compared to previous studies in which optimal methods were used, integer programming and nonlinear integer programming. Also, sensitivity analysis was applied to measure the robustness and strength of the method used, where an optimal solution was obtained for all experiments and in record time. This method can be used for power plants in privet or public sectors, to generate an optimal PMS, to save money, and to avoid water or electricity cuts.

Despite the effectiveness of insulin injections in managing hyperglycemia in Type 1 Diabetes, they fall short in addressing autoimmunity and regenerating damaged islets. This review aims to explore the potential of various treatment modalities for T1DM, including mesenchymal stem cells (MSCs), MSC-derived exosomes, gene therapy, islet allotransplantation, and pancreatic islet cell transplantation. Results: MSCs demonstrate efficacy in T1DM treatment through immunomodulation and tissue regeneration, although further research is warranted to optimize their therapeutic potential. Gene therapy presents a promising approach despite challenges such as donor shortage and immune rejection. Pancreatic islet cell transplantation emerges as a viable option, albeit with associated risks including graft rejection and the need for immunosuppression. Teplizumab, an FDA-approved humanized monoclonal antibody, revolutionizes the treatment landscape of Type 1 Diabetes by significantly delaying its onset, offering a paradigm shift since the discovery of insulin Conclusion: Ongoing studies and technological advancements in T1DM management offer a promising outlook for improved treatments and possibly even eradication on a global scale. MSCs, MSC-derived exosomes, gene therapy, and pancreatic islet transplantation hold considerable potential.

Background and Objectives: In the current Covid-19 pandemic, children below the age of 12 could manifest Covid-19 symptoms and serve as a reservoir for the virus in the community. The present study was conducted to evaluate the reactogenicity, and immunogenicity of BBIBP-CorV, prior to involving this age group in the vaccination program in the kingdom of Bahrain. Subjects and Methods: The study included 582 children from 3 to 12 years old of Bahraini and non-Bahraini nationality, all of which contributed to the reactogenicity study. Of those, 401 contributed to the immunogenicity study. All children received 2 doses of BBIBP-CorV inactivated virus 3 weeks apart. To assess reactogenicity, children were followed up for 5 weeks to evaluate any vaccine-related adverse events (AE). To assess immunogenicity, blood was collected on day 0 and day 35 to assess antibody titer against S, N, and neutralizing antibody. Results: Of the 582 participants, (45.4%) were female, (54.61%) were male, with 49% in 9-12 age group. Of the 401 children contributing to the immunogenicity study, 274 (68.3%) had no prior exposure to Covid-19. The overall incidence of AE was 27.7%. No significant difference was found among different age groups. The most frequent AE was local (at the injection site) and occurred in 16% of children, followed by fever in 9.3%. No serious adverse events were reported. The Seroconversion rate was 100% among children with no prior exposure to Covid-19. Children with previous Covid-19 exposure had higher averages of anti-S (2379 U/ml compared to 409.1), anti-N (177.6 U/ml compared to 30.9) and neutralizing antibody (93.7 U/ml compared to 77.1) than children with no prior exposure at day 35. Conclusions: Two doses of COVID-19 BBIBP-CorV on the subjects aged between 3 to 12 has good safety and tolerance and can induce an effective immune response and neutralizing antibody titer.

AI is leveraging all aspects of life. Medical services are not untouched. Especially in the field of medical image processing and diagnosis. Big IT and Biotechnology companies are investing millions of dollars in medical and AI research. The recent outbreak of SARS COV-2 gave us a unique opportunity to study for a non interventional and sustainable AI solution. Lung disease remains a major healthcare challenge with high morbidity and mortality worldwide. The predominant lung disease was lung cancer. Until recently, the world has witnessed the global pandemic of COVID19, the Novel coronavirus outbreak. We have experienced how viral infection of lung and heart claimed thousands of lives worldwide. With the unprecedented advancement of Artificial Intelligence in recent years, Machine learning can be used to easily detect and classify medical imagery. It is much faster and most of the time more accurate than human radiologists. Once implemented, it is more cost-effective and time-saving. In our study, we evaluated the efficacy of Microsoft Cognitive Service to detect and classify COVID19 induced pneumonia from other Viral/Bacterial pneumonia based on X-Ray and CT images. We wanted to assess the implication and accuracy of the Automated ML-based Rapid Application Development (RAD) environment in the field of Medical Image diagnosis. This study will better equip us to respond with an ML-based diagnostic Decision Support System(DSS) for a Pandemic situation like COVID19. After optimization, the trained network achieved 96.8% Average Precision which was implemented as a Web Application for consumption. However, the same trained network did not perform like Web Application when ported to Smartphone for Real-time inference, which was our main interest of study. The authors believe, there is scope for further study on this issue. One of the main goals of this study was to develop and evaluate the performance of AI-powered Smartphone-based Real-time Applications. Facilitating primary diagnostic services in less equipped and understaffed rural healthcare centers of the world with unreliable internet service.

The literature study delves into novel therapeutic strategies in transplantation medicine, highlighting unique approaches that could revolutionize current practices. It emphasizes novel patterns that have the potential to transform the current landscape. Commencing with a thorough examination of the historical environment, it traces crucial advances and changes in transplantation. The focus is on traditional techniques, emphasizing their limitations and challenges. An extensive examination of contemporary transplantation therapies offers valuable insights into the most recent progress in organ, cellular, and tissue transplantation. This analysis examines the immunological obstacles and outlines the current advancements and constraints. The exploration further navigates into novel models and concepts such as immunomodulation, developments in organ preservation techniques, gene editing, biomaterials, scaffold-based solutions, and the integration of precision medicine, artificial intelligence, and machine learning applications. Each section analyzes the potential for change and current progress in various areas, backed by relevant scientific sources up to 2023. The subsequent sections delve into innovative cellular therapies, biotechnological progress, current clinical trials, and case studies demonstrating effective applications. This examination delves into the ethical and regulatory considerations of innovative therapeutic procedures, emphasizing ethical implications, regulatory frameworks, and the importance of balancing innovation with patient welfare. The literature review concludes by offering a forward-looking perspective, emphasizing potential progress, anticipated challenges, and advocating for collaboration and interdisciplinary approaches to overcome limitations in the field of transplantation medicine.

In this study, the olive pomace was considered because of its importance in the environment. So, this study carried out to estimate the total nitrogen content and the fatty acids profile of olive pomace. The olive pomace samples were collected from Irbid, Jarash, Ajloun and Mafraq during the harvesting season 2014 to study the biochemical characteristics of fatty acid composition and the total nitrogen (TN) content. The total nitrogen content was determined by standard Kjeldahl method and the fatty acid profile was detected by gas chromatography (GC). The results show that the total nitrogen content ranged from (0.39 ± 0.0) to (0.62 ± 0.02) with statistically significant difference suggesting that the composition of matrices and their percentage may be responsible for composition of amendments. The calculated total protein percentage ranged between (2.43 ± 0.00) to (3.87 ± 0.17). Also, 13 different fatty acids were quantitatively profiled and quantitated. Oleic acid (C 18:1) was found to be the highest percentage of all other fatty acids and ranged between (59.03%) and (63.81%), moreover the C 18:1/C 18:2 (oil quality) was calculated and C.V% showed variation meaning that nutritional implication could affect the oxidative stability of oils. In conclusion, OP by-product could give a sustainable and alternative-cheap source for fertilizers, pharmaceutical industries, cosmetics and other industries.

Aim: This research is aimed at examining the cost-effectiveness of olanzapine versus risperidone in dementia patients with behavioural and psychological symptoms in Thailand. Methods: An existing Markov model based on a critical review through the comprehensive literature search and a justification for the most appropriate model for a Thai setting was adapted to simulate the disease progression of patients with dementia with behavioural disturbances until their need for full-time care (FTC). The time to the FTC state was estimated by a predictive equation developed by Rive et al. (2010). The model was conducted to assess the expected costs and outcomes associated with olanzapine compared with risperidone for Thai patients with BPSD aged 60 years and above. This model performed over a five-year time horizon with a one-month cycle length based on a societal perspective. The incremental cost-effectiveness ratio was used as the estimated outcome. Sensitivity analyses were also conducted to demonstrate the robustness of the results. Results: Over 5 years, olanzapine was found to be a cost-effective therapeutic option for the treatment of behaviourally disturbed patients with dementia compared with risperidone, in Thailand from a societal perspective (ICER < THB 160,000). The model underwent extensive sensitivity analyses, which also confirmed that olanzapine was the dominant strategy following the base-case findings. Conclusions: By comparison with risperidone, the model suggests that olanzapine can be regarded as a cost-effective therapeutic strategy for the management of patients with behavioural and psychological symptoms in Thailand.

The variability of ozone over Egypt has been studied in this work. Higher values of coefficient of variation (COV) at eight stations occur at winter while lowest values occur at summer. The COV is function of latitude in annual, winter and spring where it decreases gradually from the north to south of Egypt. The trend analysis of ozone over the eight stations indicates negative trends over northern stations for both annual and seasonal time series with the greatest one at winter. The horizontal distribution of ozone trend values is negative over all Egypt in winter while it positive over middle and south Egypt in the other seasons. The long-term variability of the behavior of the annual ozone shows positive trend values in ozone are the dominant features during the period 1979- 1989 at the most stations. Negative trend values in ozone are the dominant features during the period 1990- 2014 at all stations. The Mann–Kendall test confirms that there is an abrupt change towards decreasing of ozone occurs in 1981, 1984, 2012, 1999, 2000, 1998 and 2010, while a change towards increasing of ozone appears in 2006, 2014, 1993 and 1989.

Demand for environmentally friendly types of energy is growing all over the world, which naturally increases the intensity of work on the production of hydrogen-containing fuel mixtures. Steam reforming of methanol is one of the most effective areas of research, as it is a process with low energy consumption. The results of steam reforming of methanol on the catalysts prepared by solution combustion synthesis (SCS) and impregnation by moisture capacity are presented. Investigation of the activity of Cu-Ce-Al catalysts of different composition was carried out for production of hydrogen and comparison of SCS with traditional impregnation method. Methanol conversion reaches 99%, while the selectivity of H2 was 88%, at 500 °C. It was found that CuAl2O4 spinel formation is due to substitution of Al3+ with Cu2+ Ce3+ cations. A consequence CuAl2O4 and CeAlO3 lattice parameters increase because of difference in ionic radius of Al3+ (0.53 Å) and Cu2+ (0.73 Å), Ce3+ (1.07 Å). Advantages of SCS catalysts in steam reforming of methanol were shown. The aim of this research is to develop a new catalyst for conversion of methanol into hydrogen containing fuel mixtures, which will further promote the organization of a new era of environmentally friendly energy-saving production methods.

In recent years, semantic communication has received significant attention from both academia and industry, driven by the growing demands for ultra-low latency and high-throughput capabilities in emerging intelligent services. Nonetheless, a comprehensive and effective theoretical framework for semantic communication has yet to be established. In particular, finding the fundamental limits of semantic communication, exploring the capabilities of semantic-aware networks, or utilizing theoretical guidance for deep learning in semantic communication are very important yet still unresolved issues. In general, the mathematical theory of semantic communication and the mathematical representation of semantics are referred to as semantic information theory. In this paper, we introduce the pertinent advancements in semantic information theory. Grounded in the foundational work of Claude Shannon, we present the latest developments in semantic entropy, semantic rate-distortion, and semantic channel capacity. Additionally, we analyze some open problems in semantic information measurement and semantic coding, providing a theoretical basis for the design of a semantic communication system. Furthermore, we carefully review several mathematical theories and tools and evaluate their applicability in the context of semantic communication. Finally, we shed light on the challenges encountered in both semantic communication and semantic information theory.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of simulation and statistical results of EO with other optimization techniques showed that EO is more effective and superior.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus 13 voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ 14 constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources 15 on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar 16 PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed 17 using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of 18 simulation and statistical results of EO with other optimization techniques showed that EO is more effective 19 and superior.

The prevalence of autism in children in the world is estimated as one per 62 children, higher levels reported in some countries. These children experience significant problems with the development of social, behavioural and verbal and non-verbal communication skills. The skills impairment levels varies from an individual to another and that made teaching autistics a challenge for caregivers such as teachers and relatives. Hence, there are quite a number of frameworks of a software learning systems which focus on gaining the children’s attention using representational visual illustration as a learning method instead of the textual form. However, majority of these tools are lacking the personalisation ability to suite everyone in the spectrum. Assistive technology offers an alternative way to attract children with autism. Therefore, this research is proposing an Adaptive Content Management Learning System (ACMLS) model to assist caregivers to produce, design and fine-tune or customise the learning materials appropriately so that the system interface and the materials are suitable for every individual in the spectrum according to each child personal profile aiming to make learning attractive and to contribute in improving their social, communication and behavioural skills and nonetheless, their attention level to the delivered educational topics. The ACMLS model design adopts four main components which are: (1) Design component: which covers the visual design, design principles and the mental model of the children with autism. (2) Technology component: which covers the assistive technology tools and the architecture of the ACMLS system. (3) Education component: Which covers the learning objectives, styles, strategies, methods and the cognitive model. (4) Participants component: which covers the main participants who’re playing a role in the ACMLS model such as: caregivers and children with autism.

The prevalence of autism in children in the world is estimated as one per 62 children, higher levels reported in some countries. These children experience significant problems with the development of social, behavioural and verbal and non-verbal communication skills. The skills impairment levels varies from an individual to another and that made teaching autistics a challenge for caregivers such as teachers and relatives. Hence, there are quite a number of frameworks of a software learning systems which focus on gaining the children’s attention using representational visual illustration as a learning method instead of the textual form. However, majority of these tools are lacking the personalisation ability to suite everyone in the spectrum. Assistive technology offers an alternative way to attract children with autism to use. Therefore, this research is proposing Autism Content Management Learning System (ACMLS) Framework to assist caregivers to produce, design and fine-tune or customise the learning materials appropriately so that the system interface and the materials are suitable for every individual in the spectrum according to each child personal profile aiming to make learning attractive and to contribute in improving their social, communication and behavioural skills and nonetheless, their attention level to the delivered educational topics. The ACMLS framework design adopts four main components which are: (1) Design component: which covers the visual design, design principles and the mental model of the children with autism. (2) Technology component: which covers the assistive technology tools and the architecture of the ACMLS system. (3) Education component: Which covers the learning objectives, styles, strategies, methods and the cognitive model. (4) Participants component: which covers the main participants who’re playing a role in the ACMLS framework such as: caregivers and children with autism.

Background: Asthma is a widespread chronic respiratory disease that poses a significant public health challenge. The current study investigated the associations between air pollution and asthma severity among individuals residing near the Sohar industrial port (SIP) in Oman. Despite the presence of multiple major industrial complexes in Oman, limited knowledge regarding their impact on respiratory health is accredited. Hence, the primary objective of this study is to offer valuable insights into the respiratory health consequences of industrial air pollution in Al Batinah North. Methods: The state health clinics' records for patient visits related to asthma were collected for the timeframe spanning 2014 to 2022. Exposure was defined as the distance from SIP, Majan Industerial Area (MIA) and Sohar Industerial Zone (SIZ) to determine high, intermediate, and low exposure zones (12 km, respectively). Exposure effect modifications by age, gender, and smoking status were also examined. Results: The conducted cross-sectional study of 410 patients (46.1% males and 53.9% females) living in over 17 areas around SIP revealed that 73.2% of asthmatics were under 50 years old, with severity significantly associated with closeness to the port. Risk ratios were estimated to be (RR:2.42; CI95%: 1.01–5.78), (RR:1.91; CI95%: 1.01–3.6), and (RR:1.68; CI95%: 0.92–3.09) for SIP, MIP and SIZ areas, respectively, compared to the control area. Falaj Al Qabail (6.4 km) and Majees (6 km) had the highest number of asthma patients (N. 69 and N. 72), and highest percentages of severe asthma cases among these patients (28% and 24%) with significant risk ratios (RR:2.97; CI95%: 1.19–7.45 and RR:2.55; CI95%: 1.00–6.48), correspondingly. Moreover, severe asthma prevalence peaked in the 25-50 age group (RR:2.05; CI95%: 1.26–3.33), and this linkage between asthma and age was much more pronounced in males than females. Smoking and exposure to certain contaminant (dust and smoke) increased also the risk of severe asthma symptoms, but their effects were less important in the high risk zone, suggesting much more important risk factor. A neural network model accurately predicted asthma risk (94.8% accuracy), with proximity to Sohar Industrial Port as the most influential predictor. Conclusion: The study highlights the High asthma burden near Sohar Industrial Port, linked to port proximity and smoking and wind direction as major risk factors. These findings inform vital public health policies to reduce air pollution and improve respiratory health in the region, prompting national policy review.

In Bangladesh, family businesses play a significant role in the country's business landscape because so few private companies are set up as large-scale, non-family ownership firms. Thus, it is vital to comprehend family businesses in order to comprehend Bangladeshi company dynamics. In this paper, authors attempted to survey the existing research in the area of family business in Bangladesh. It was found that the area as a research is totally an open field and a lot of new research can be done in the said area. Although a good number of studies can be classified as focused on the SME (small and medium enterprise) domain, a major shortcoming of those SME studies is that the SMEs themselves vary greatly in terms of size, scope, and technology. Whereas most of the family businesses can be predominantly put in the SME category, the particular issue of family business and family dynamics is not very common in those studies. This paper suggests that a good amount of research or studies can be done focusing on family business constitution, family members' participation norm, recruitment and promotion norm, family business succession rules and succession planning, training for family business leadership and management, training for board and directorial supervision, and so on.

In this study, we introduce the dynamics of a Hepatitis B virus (HBV) model with the class of asymptomatic carriers and conduct a comprehensive analysis to explore its theoretical aspects and examine the crossover effect within the HBV model. To investigate the crossover behavior of the operators, we divide the study interval into two subintervals. In the first interval, the classical derivative is employed to study the qualitative properties of the proposed system, while in the second interval, we utilize the ABC fractional differential operator. Consequently, the study is initiated using the piecewise Atangana-Baleanu derivative framework for the systems. The HBV model is then analyzed to determine the existence, Hyers-Ulam (HU) stability, and disease-free equilibrium point of the model. Moreover, we showcase the application of an Adams-type predictor-corrector (PC) technique for Atangana-Baleanu derivatives and an extended Adams-Bashforth-Moulton (ABM) method for Caputo derivatives through numerical results. Subsequently, we employ computational methods to numerically solve the models and visually present the obtained outcomes using different fractional-order values. This network is designed to provide more precise information for disease modeling, considering that communities often interact with one another, and the rate of disease spread is influenced by this factor.

Image segmentation is a new challenge prob- lem in medical application. The use of medical imaging has become an integral part of research, as it allows us to see inside the human body without surgical intervention. Many researcher have studied brain segmentation. One stage method is used to segment the brain tissues. In this paper, we proposed the multi-stage generative ad- versarial network to solve the problem of information loss in the one-stage. We utilize the coarse-to-fine to improve brain segmentation using multi-stage generative adversar- ial networks (GAN). In the first stage, our model generated a coarse outline for (i) background and (ii) brain tissues. Then, in the second stage, the model generated outline for (i) white matter (WM), (ii) gray matter (GM) and (iii) cerebrospinal fluid (CSF). A good result can be achieved by fusing the coarse outline and refine outline. We conclude that our model is more efficient and accu- rate in practice for both infant and adult brain segmenta- tion. Moreover, we observe that multi-stage model is faster than prior models. To be more specific, the main goal of multi-stage model is to see the performance of the model in a few shot learning case where a few labeled data are available. For medical image, this proposed model can work in a wide range of image segmentation where the convolution neural networks and one-stage methods have failed.

Calcium phosphates and manganese phosphates play a significant role in biomedical and engineering applications, and these compounds are both synergistic. These compounds could have great potential for use in different applications, particularly as precursors of biomaterials. Therefore, the aim of this study was to explore the effect of the gradual replacement of Ca2+ with Mn2+ on the phase composition and crystal structure of brushite (CaHPO4·2H2O), which could be useful for the production of Mono- and Biphasic Ca1−xMnxHPO4·nH2O Compounds. In order to prepare the starting solutions required for this study, Ca(NO3)2·4H2O, (NH4)2·HPO4, and Mn(NO3)2·4H2O were used at various molar concentrations. Afterwards, the Ca1−xMnxHPO4·nH2O compounds were prepared using dissolution and precipitation methods. These compounds were characterized using XRD, SEM, FT-IR, XPS, and TGA techniques. The findings revealed that Mn substituted Ca partially at low Mn/Ca molar ratios, 0.25, and Mn doping increased the unit cell of CaHPO4·2H2O. The produced biphasic compound was composed of monoclinic CaHPO4·2H2O and nanostructured orthorhombic MnHPO4·(H2O)3 after a continuous increase in the Mn/Ca molar ratio to 1.5. When the Ca/Mn molar ratio was above 1.5, a monophasic compound of the MnHPO4·(H2O)3 phase was formed. The MnHPO4·(H2O)3 compound was successfully prepared for the first time using this dissolution-precipitation method. It was also established that the Mn/Ca ratio of the starting solution can be modified to produce CaHPO4·2H2O and MnHPO4·(H2O)3 phases with specific weight percent compositions.

The key question for the understanding of corrosion phenomena of Si3N4-SiC material in Al reduction cell – whether corrosion by gases (and oxidation in particular) opens way for the corrosion by molten cryolite, or corrosion of Si3N4-SiC by cryolite plays its own role in degradation of the material in service. More probably the reactions of silicon carbide and silicon nitride with molten cryolite go after the stage of pre oxidation to silicon dioxide. The corrosion of Si3N4-SiC material in the reduction cell may take place by “gas-solid” reaction and by “liquid-solid” reaction. There are several variants of lab corrosion test for the evaluation of corrosion resistance of Si3N4-SiC material to cryolite. The results of investigation of Si3N4-SiC lab corrosion test give no direct evidence of selective dissolution of specific phase (Si3N4 or SiC, α-Si3N4 or β-Si3N4) in cryolite. The existing variants of lab corrosion testing require clarification.

κ Draconis is a binary system with a classical Be star as the primary component. Its emission-line spectrum consists of hydrogen lines, notably the Hα line with a peak intensity ratio (V/R) variations phase-locked with the orbital period P = 61.55 days. Among binaries demonstrating the Be phenomenon, κ Dra stands out as one of a few systems with a discernible mass of its secondary component. Based on more than 200 spectra obtained in 2014 − 2023, we verified the physical parameters and constructed the mass function. We used part of these data obtained in 2014 − 2021 to investigate regions in the circumstellar disk of the primary component that emit the Hα line using the Doppler tomography method. The results show that the disk has a non-uniform density distribution with a prominent enhancement at Vy≈ 99 km s−1 and Vx≈−6 km s−1 that corresponds to a cloud-like source of the double-peaked Hα line profile. We argue that this enhancement’s motion is responsible for the periodic variations of the Hα V/R ratio, which is synchronised in orbital phase with the radial velocity (RV) of absorption lines from the atmosphere of the primary component.

Silicon carbide particle-reinforced aluminum matrix (SiCp/Al) composites are significant lightweight metal matrix composites extensively utilized in precision instruments and aerospace sectors. Nevertheless, the inclusion of rigid SiC particles exacerbates tool wear in mechanical machining, resulting in a decline in the quality of surface finish. This work undertakes a comprehensive investigation into the problem of tool wear in SiCp/Al composite materials throughout the machining process. Initially, a comprehensive investigation was conducted to analyze the effects of cutting velocity vc, feed per tooth fz, milling depth ap, and milling width ae on tool wear during high-speed milling under SCCO2-MQL (Supercritical Carbon Dioxide Minimum Quantity Lubrication) ultrasonic vibration conditions. Furthermore, a prediction model for tool wear was developed by employing the orthogonal test method and multiple linear regression. The model's relevance and accuracy were confirmed using F-tests and t-tests. Ultimately, through the utilization of a genetic algorithm, the milling parameters were optimized, resulting in the identification of the most optimal combination of parameters. Empirical findings suggest that the careful selection of milling parameters can significantly mitigate tool wear, extend the lifespan of the tool, and enhance the quality of the surface. This work serves as a significant point of reference for the processing of SiCp/Al composite materials.

Background: Despite their generally favorable prognosis, hepatic fibrosis remains a possible complication for hepatitis B virus (HBV) inactive carriers. This study aimed to estimate the prevalence of significant fibrosis and associated risk factors among Omani HBV inactive carriers. Methods: A retrospective study was conducted of 200 Omani HBV inactive carriers visiting a tertiary hospital in Muscat, Oman, between January 2017 and December 2018. Significant fibrosis (stage F2 or higher) was identified using two-dimensional shear-wave elastography. Baseline clinical, laboratory, and radiological data were analyzed to determine associations. Results: Of the total sample, 106 patients (53%) were male, and the mean age was 44.6 ± 9.3 years. The prevalence of significant fibrosis was 20% (n = 40). Male gender (p = 0.007), age ≥60 years (p = 0.024), and fatty changes in liver ultrasound (p = 0.044) were found to be independent factors for significant fibrosis. Conclusion: the prevalence of significant fibrosis was relatively high among a sample of Omani HBV inactive carriers, with several sociodemographic and clinical risk factors identified. Periodic assessment of liver function is needed for patients with these risk factors; moreover, routine biochemical parameters could be useful predictors of disease prognosis. Further research is recommended to substantiate these findings.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

Nowadays recurrent implantation failure (RIF) after invitro fertilization is common problem that reproductive specialists usually faced. The phenomenon of thin endometrium in RIF patients has yet not completely understood and properly treated. This study aimed to reveal significantly dysregulated selected genes expression between RIF patients with thin endometrium and fertile women. Endometrial samples were collected in the implantation window days (LH+7 – LH+10) of the natural menstrual cycle from RIF patients (n=20) and fertile women (n=14). Ten genes were chosen as target genes regarding their possible relations with the implantation process. Endometrial gene expression levels showed differences in RIF samples compared to fertile samples. The significant downregulation was observed for CXCL1 (p=0.005) and C4BPA (p=0.03) genes. There was no statistically significant difference between the RIF groups and the fertile group in the expression of 8 genes: CXCL8, HPRT1, MMP10, INFG, VEGFB, HAND2, IL15 and TNC (p&gt;0.05). The use of a combination of two markers (C4BPA + CXCL1) allows for good discrimination of RIF patients from fertile women (AUC 0.806).

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Saudi Arabian cities have experienced a rapid expansion of their urban areas - particularly their city centers - over the last four decades. This has resulted to an increase in vehicular usage, which has adversely affected the daily walking experience of the residents. Walkability has several positive effects on people's health as well as the environment in cities. In addition to being a means of transportation, it also helps people create a sense of place, enhancing their image ability to be easily understood as a legible urban structure, and deepen their emotional bond with the city. Using the medium-sized Saudi Arabian city of Onaizah as a case study, this study looks into the feasibility of creating urban walking corridors to encourage users to walk more. According to Saudi Arabia's Vision 2030, which emphasizes the value of sustainable urban development and raising quality of life for residents, the study addresses walkability as a generator to maintain and improve the urban scene of the city center. Geographic Information Systems (GIS) was used to analyze the data and generate the urban corridors in the city center. The results showed the possibility of improving walking in Onaizah through three urban corridors to the city center, measuring 1,401 meters, 1,283 meters, and 1,507 meters, respectively. These corridors represent urban, commercial and heritage corridors, giving an opportunity for planners and decision makers to challenge prioritize pedestrian connectivity and enhance the physical environment, leading to sustainable urban development. This research paper used various criteria analysis methods to provide a comprehensive assessment of various factors to conclude these urban corridors; for example, assessments of land use, transportation and environmental considerations. The study aligns with Saudi Arabia's vision 2030 by promoting walking and enhancing the city's overall walkability while offering Onaizah society by creating and suggesting urban corridors to the city center a sustainable and livable urban environment.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

Reproductive disorders are a common event in modern reproductive medicine, occurring both in spontaneous and assisted pregnancies. Studies of the molecular mechanisms of implantation disorders in thin endometrium, including the study of gene transcriptional activity, have shed light on the identification of potential biological markers of endometrial receptivity. Background/Objectives: to reveal significantly dysregulated selected genes expression between RIF and RPL patients with thin endometrium. Methods: Endometrial samples were collected in the implantation window days (LH+7 – LH+10) of the natural menstrual cycle from RIF patients (n=20) and RPL patients (n=19). Ten genes were chosen as target genes regarding their possible relations with the implantation process. Total RNA was purified, reverse-transcribed; gene expression was quantified by RT-PCR. Results: The expression of the IL-15, INFG and HPRT1 genes were significantly decreased in RIF with thin endometrium patients compared to the RPL patients (log2 fold change=0.92, p=0.023 for IL-15, log2 fold change=1.24, p=0.046 for INFG, and log2 fold change=0.579, p=0.046 for HPRT1). There were not significant differences in expression of CXCL8, CXCL1, MMP10, C4BPA, TNC, VEGFB and HAND2 genes between groups. Conclusions: decreased expression of IL-15, INFG and HPRT1 genes was found in patients with RIF with thin endometrium compared to the endometrium of women with RPL. This has practical significance for clinicians for differentiated prescription of immunomodulatory therapy in patients undergoing ART programs.

Peste des Petits Ruminants (PPR) is one of the major transboundary animal diseases that severely impact livestock production and trade worldwide. An investigation was carried into the seroprevalence and risk factors of PPR in small ruminants, camels, and wild ruminants in Bahrain. A total of 1240 serum samples were collected from 119 sheep flocks and 1224 serum samples from 125 goat herds. In addition, 100 sera from camels and 38 sera from wild ruminants, were collected. Serum samples were tested for the presence of PPR specific antibodies using a competitive ELISA. Flock management and health information of the flocks and herds were collected using a semi-structured questionnaire. The individual prevalence of PPR in sheep and goats was 26% and 25.5%, respectively. The flock or herd level prevalence of PPR was 22.7% and 29.6% in sheep and goats, respectively. None of the tested camels or wild ruminants were positive for PPR-specific antibodies. Sheep and goats from the Northern governorate were more likely to be seropositive to PPR than in other governorates. On the individual animal level, the univariate analysis suggested; age (&lt;12 months), sex (male), and health status (weak animals) as risk factors for PPR seropositivity. On the flock/herd level, the multivariable logistic regression analysis identified large flock/herd size and semi-intensive farming as risk factors for PPR seropositivity.

In contemporary times, the landscape of malware analysis has advanced into an era of sophisticated threat detection. Today's malware sandboxes not only conduct rudimentary analyses but have evolved to incorporate cutting-edge artificial intelligence and machine learning capabilities. These advancements empower them to discern subtle anomalies and recognize emerging threats with a heightened level of accuracy. Moreover, malware sandboxes have adeptly adapted to counteract evasion tactics, creating a more realistic and challenging environment for malicious entities attempting to detect and evade analysis. This paper delves into the maturation of malware sandbox technology, tracing its progression from basic analysis to the intricate realm of advanced threat hunting. At the core of this evolution is the instrumental role played by malware sandboxes in providing a secure and dynamic environment for the in-depth examination of malicious code, contributing significantly to the ongoing battle against evolving cyber threats. In addressing the ongoing challenges of evasive malware detection, the focus lies on advancing detection mechanisms, leveraging machine learning models, and evolving malware sandboxes to create adaptive environments. Future efforts should prioritize the creation of comprehensive datasets, distinguish between legitimate and malicious evasion techniques, enhance detection of unknown tactics, optimize execution environments, and enable adaptability to zero-day malware through efficient learning mechanisms, thereby fortifying cybersecurity defences against emerging threats.

Soil moisture modeling is necessary for many hydrometeorological and agricultural applications. One of the ways in which modeling of soil moisture (SM) can be improved is by assimilating SM observations to update the model states. Remotely sensed SM observations are prone to being riddled with data discontinuities, namely in the horizontal and vertical spatial, and temporal dimensions. A set of synthetic experiments were designed in this study to assess how much impact each of these individual components of spatiotemporal gaps can have on the modeling performance of SM as well as streamflow. Results show that not having root-zone SM estimates from satellite derived observations is most impactful in terms of modeling performance. Having temporal gaps and horizontal spatial gaps in the satellite SM data also impacts modeling performance, but to a lesser degree. Real-data experiments with the remotely sensed Soil Moisture Active Passive (SMAP) product generally brought improvements to the SM modeling performance in the upper soil layers, but not so much in the bottom soil layer. The updating of model SM states with observations also resulted in some improvements in the streamflow modeling performance during the synthetic experiments, but not during the real-data experiments.

Gestational trophoblastic diseases (GTDs) encompass a spectrum of conditions characterized by abnormal trophoblastic cell growth, ranging from benign molar pregnancies to malignant trophoblastic neoplasms. This systematic review explores the molecular underpinnings of GTDs, focusing on genetic and epigenetic factors that influence disease progression and clinical outcomes. Based on 65 studies identified through systematic search and selection criteria, key findings include dysregulations in tumor suppressor genes such as p53, aberrant apoptotic pathways involving BCL-2, and altered expression of growth factor receptors and microRNAs. These molecular alterations not only differentiate molar pregnancies from normal placental development but also contribute to their clinical behavior, from benign moles to potentially malignant forms. The review synthesizes insights from immunohistochemical studies and molecular analyses to provide a comprehensive understanding of GTD pathogenesis and implications for personalized care strategies.

Salmonella Typhimurium is a typical Gram-Negative bacterium associated with food-borne illness threatening public health. This pathogen is reported to have caused millions of infections and thousands of hospitalizations yearly in the United States alone. Salmonella Typhimurium has a sophisticated array of virulent factors, including its flagella, which contributes significantly to its pathogenicity. Cannabidiol (CBD), the non-psychoactive component of the cannabis plant, has attracted the interest of many researchers recently because of its antimicrobial properties. With the growing interest in exploring CBD’s antimicrobial properties, we, in this study, have delved into unravelling how prolonged exposure of Salmonella Typhimurium to CBD influences the expression of the flgA gene. We hypothesized that the exposure of Salmonella Typhimurium to CBD may result in flgA upregulation, causing the bacteria to withstand various stresses and potentially enhance its survival rates and pathogenicity. We have employed several assays, such as mRNA expression, motility assays, pH induction assays, nutrient starvation interventions, and biofilm analysis, to explore the influence of CBD on the pathophysiology of Salmonella Typhimurium. Our findings reveal that CBD-resistant strains exhibit enhanced resilience to extreme pH levels and motility and survive poorly under nutrient starvation, with more robust biofilm formation compared to the susceptible strains. The results contribute to the broader comprehension of CBD resistance mechanisms in bacteria. This work provides insight into the potential therapeutic interventions for controlling CBD-resistant bacterial infections. This study also underscores the essence of exploring novel alternative antimicrobial agents to tackle the ever-persistence of bacterial antibiotic resistance.

Water is essential for all living things however its pain has become serious. Many industrial activities cause its pollution by the release of polluting byproduct. Waste water treatment is hence necessary. In this context, the waste water of the textile industry containing Red Acid 52 was treated by the solid waste of the washed natural phosphate byproduct. Natural phosphate was also studied. The solid materials were first characterized by chemical analysis, Fourier Transform Infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The phosphate materials were after that, tested in the adsorption of the Red Acid 52. The experimental data indicated that the phosphate waste rock allowed the removal of Red Acid 52. Its maximum retention capacity attained 18.4 mg.g-1. Calcinations of materials inhibits the removal capacity found reduced by 60 to 70%. The adsorption kinetics of the Red Acid 52 on the material is well described by the pseudo second order model while the adsorption isotherms are identified by the Langmuir model. Hereafter, the thermodynamic study revealed that the adsorption process is spontaneous and exothermic. Keywords: Waste water, Phosphate co-product, Adsorption, Red Acid 52.

The endocannabinoid system (ECS) is a complex neuromodulatory network in the human body that have enormous impact in developing the central nervous system, as well as modulates various physiological processes. The ECS is made up of anandamide, 2-arachidonoylglycerol (2-AG), which are responsible for the synthesis and degradation of endocannabinoids, and enzymes such as FAAH and MAGL ensures the precise control over endocannabinoid levels. The ECS relies on CB1 receptors found in the central nervous system (CNS), and CB2 receptors found in the peripheral nervous system and immune cells. Dysregulation of the ECS has been associated with several health conditions, prompting investigations into its association with phytocannabinoids to harness their therapeutic potential. The ECS is intricately linked with the nervous system, and it is known to modulate neuronal activities in the CNS, influencing pain and mood modulation. The ECS is also associated with neuropathies-peripheral nerve damage leading to symptoms such as weakness, numbness and pain as evidenced in diabetic neuropathy, Guillain-Barré Syndrome, carpal tunnel syndrome, peripheral neuropathy, and postherpetic neuralgia. The focus of this review is on the interplay between 2-arachidonoylglycerol and anandamide amidohydrolase in neuropathy, elucidating their roles in pain regulation, inflammation, and specific neuropathies. The knowledge generated is expected to have broad implications, providing comprehensive insights into neuropathic conditions and how to improve on them. Ultimately, this understanding may lead to more effective treatments and improved quality of life for individuals affected by these conditions.

Learning dental procedures is a complex task involving the development of fine motor skills. The reported use of theories and/ or evidence for designing learning activities to develop the fine motor skills needed for dental practice is limited. The aim of this review is to explore the available body of knowledge related to learning fine motor skills in dentistry. Evidence from studies investigating motor skill learning highlights the negative impact of self-focus and self-regulation on learning outcomes, particularly during the early stages of learning. The development of activities and schedules that enable novices to demonstrate characteristics similar to experts, without the reported long period of ‘deliberate practice’, is clearly of value. Outcomes of learning implicitly are important in dentistry because working under stressful conditions is common, either during undergraduate study or in practice. It is suggested that learning implicitly in the simulation stage can reduce disrupted performance when transitioning to clinical settings. Therefore, further investigation of effective methods for learning dental fine motor skills is indicated, using approaches that result in robust performance, even under stressful conditions.

Over the years, the need for autonomous systems such as drones, also known as unmanned aerial vehicles (UAVs), has significantly increased in popularity across several industries, including the military. The Internet of Battlefield Things (IoBT) represents a modern technological advancement that significantly enhances the operational efficacy of defense systems. It establishes an integrated military force by connecting individuals to intelligent technology in drones, radios, equipment, antennas and ground stations. This is achieved through the utilization of cloud and edge computing, sensors, mobile devices, embedded systems, and IoT-based systems. However, IoBT security is significantly compromised by enemies that exploit the vulnerabilities and malicious intrusions that specifically target the external environment or to obtain sensitive data. In addition, a comprehensive understanding of cyberattacks and countermeasures is essential for assuring the security of IoBT. On the other hand, as cyber threats get more complicated, trust becomes increasingly important for the security of digital systems. Within this context, the zero trust architecture contends that the security of a complex network is inherently vulnerable to internal and external threats. In defense, UAV security system applications, for example, the primary purpose of the zero trust architecture is to limit the vulnerability of military UAV systems to cyberattacks, hence reducing the possibility of data breaches and illegal entry. This study conducts a systematic review aimed at identifying different aspects of cybersecurity strategies for protecting UAV systems within the IoBT domain. Furthermore, zero trust architecture is presented in the study as an effective prospective solution to the security issues that develop in defense UAV systems.

High dimensional datasets are highly likely to have redundant, irrelevant, and noisy features that negatively affect the performance of the classification algorithms. Selecting the most relevant features and reducing the dimensions of datasets by removing the undesired features is a dimensional reduction technique called Feature Selection (FS). In this paper, we propose an FS approach based on the Black Hole Algorithms (BHO) with a mutation technique called MBHO. Generally, BHO contains two major phases. At the exploitation phase, a set of stars are modified based on some rule and according to some objective function, the best star is selected as the black hole which attracts other stars. Furthermore, when a star gets closer to the event horizon, it will be swallowed and a new one will be randomly generated in the search space which thus is the exploration phase. However, randomness may cause the algorithm to fall into the trap of local optima, and to overcome such complications, inversion mutation is used. Furthermore, we modify a widely utilized objective function in most of the proposed works for wrapper feature selection by combining two new terms that are based on the correlation among the selected subset of features and the features and the classification label. We also utilize a transfer function, known as the V2 transfer function, to convert continuous values into discrete ones to enhance search. We assess our approach via extensive evaluation experiments using fourteen benchmark datasets. We benchmark the performance of a wrapper FS approach called Binary Cuckoo Search (BCS), and three filter-based FS approaches (namely Mutual Information Maximisation (MIM), Joint Mutual Information (JMI), and minimum Redundancy Maximum Relevance (mRMR)). Our evaluation has shown that the proposed model is an effective approach for FS, in selecting better features that enhance the performance metrics on the classifiers. Thus, MBHO can be utilized as one alternative to the existing state-of-art-approaches. We release the source codes of our implementation for the community to build on with new methods and datasets.

This study employs Geographic Information System (GIS) techniques to evaluate the walkability of Onaizah City, which serves as a representative model for a Saudi city situated in the Qassim region, north of the capital city, Riyadh. The goal is to evaluate how easily pedestrians can navigate the street network and identify areas that excel or need improvement in terms of walkability. The results offer insights for planning and development supporting sustainable initiatives. Approach; The study involves integrating GIS data, such as street layouts, land use patterns, and demographic information. By analyzing factors like integration values and choice values within the street network the study gauges’ walkability aspects. Furthermore, correlation analysis explores how spatial arrangements, influence walkability. By studying the case of a medium-sized Saudi city, which can then be applied to several Saudi cities. Cost distance analysis and cost-back correlation calculations are employed to determine pedestrian routes. Findings and Discussion; Through GIS techniques the study effectively assesses the walkability of Onaizah City by identifying three walking paths with lengths of (1401m, 1283m, and 1507m). The study reveals pedestrians' actual city distance. Weighted criteria assign 40% to heritage sites, 30% to green spaces, and 15% each to mosques/commercial sites. Preserving access to heritage sites and incorporating areas enhance walkability. Conclusion: Study enhances walkability understanding, offering data-driven planning suggestions. Urban planners prioritize pedestrian connectivity, considering GIS effectiveness and physical environment importance. Findings support walkability research and sustainable urban development.

Background/Purpose: Over the last two decades, malaria has remained a major worldwide public health concern, especially in the developing countries leading to high morbidity and mortality among children. Nigeria is the world most burdened malaria endemic nation, contributing more than a quarter of global malaria cases. This study determined the prevalence of malaria among children 6-59 months in Nigeria, and the effects of individual and contextual factors. Methods: The study utilized data from 2018 Nigeria Demographic and Health Survey (NDHS) involving a weighted sample size of 10,185 children who were tested for malaria using rapid diagnostic test (RDT). Given the hierarchical structure of the data set, such that children at level-1 are nested in community at level-2, and nested in states and Federal Capital Territory (FCT) at level-3, multilevel mixed effect logistic regression models were used for the analysis. Results: The proportion of children 6-59 months of age in Nigeria that had malaria fever positive as assessed by RDTs was 35.5% (3,418/10185), (CI: 33.9-37.1). Kebbi State had the highest proportion of children 6-59 months who were malaria positive, 77.6%, (CI: 70.2-83.5), followed by Katsina State, 55.5%, (CI: 47.7-63.1). The Federal Capital Territory (FCT), Abuja had the proportion of 29.6%, (CI: 21.6-39.0), malaria positive children of 6-59 months of age. Children between the age of 48 and 59 months were 2.68 times more likely to have malaria fever than children 6-11 months of age (AOR=2.68, 95% CI: 2.03-3.54). Also, children from the rural area (AOR= 2.12, 95% CI: 1.75-2.57), were more likely to suffer from malaria infection compare with children from urban area. Conclusion: The study identified some individual and contextual predictors of malaria among children in Nigeria. These factors are areas that need to be considered for policy designs and implementations toward control and total elimination of malaria-related morbidity and mortality among children in Nigeria.

This article delves into the enduring relevance of Liberal International Relations (IR) Theory amidst persistent criticisms regarding power dynamics and its applicability in emerging states. Despite its detractors, Liberal IR Theory offers a nuanced understanding of state behavior, blending social contexts with power dynamics. It recognizes the intricacies of economic interdependence and advocates for a balanced approach in advancing democracy and human rights. While nationalism poses challenges to international institutions, their adaptability endures. Leaders, albeit constrained, retain the capacity to foster peace through visionary leadership and global cooperation. By acknowledging its limitations and fostering open dialogue, Liberal IR Theory continues to evolve, poised to contribute to a just and peaceful global order.

The paper delineates the developed vision system of the UR5 cobot and the operating algorithm of the robotic quality control station. The hardware-software architecture of the developed robotic station was shown, consisting of a UR5 cobot equipped with a web camera and a stationary industrial camera with a lighting system. Image processing and analysis algorithms were described, the method of control and communication between the station components was discussed, and two operating scenarios were presented as a single robotic station and a robotic line. Based on the results obtained, the level of measurement noise, accuracy, and repeatability of the developed vision system were estimated.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

Dietary habits, including meal frequency, meal timing, and skipping meals, have been extensively studied due to their association with the development of non-communicable diseases (NCDs). This study describes dietary habits, meal timing, meal frequency, skipping meals, and late-night eating in Kuwaiti adults. The Kuwait National Nutrition Surveillance System data was utilized to reach the objectives of this study. The findings reveal that approximately 50% of the adults in Kuwait eat after 10 p.m., 29% skip breakfast, and 9.8% skip dinner. Furthermore, adults in Kuwait consume 4.4 meals per day on average. Women skip breakfast more often and have extended night fasting than men (p&lt;0.001). Married adults skip breakfast and dinner less than unmarried adults (p&lt;0.001). In conclusion, this descriptive study provides valuable insights into the dietary habits of Kuwaiti adults, emphasizing the importance of further investigating the association between meal timing, meal frequency, and the prevalence of NCDs in Kuwait.

Background/Objectives: Multiple sclerosis (MS) is a chronic neurological disorder characterized by various clinical presentations and manifestations that include biopsychosocial impediments. This study has three interrelated goals relevant to biopsychosocial functioning. The first is to compare cognitive, neuropsychological, and affective functioning and quality of life between patients with MS (PwMS) and a control group. The second is to examine whether cognitive and neuropsychological performance is affected by gender, and the third is to examine whether variation in QoL hinges on cognitive neuropsychological performance. Methods: This multicenter study was carried out among clinically stable PwMS under follow-up in two tertiary care units in urban Oman. Healthy controls, matched for age and sex, were also recruited as a comparison group. Data were collected using cognitive batteries sensitive to current reasoning ability and conventional neuropsychological batteries designed to measure verbal learning, visual-spatial ability, and processing speed. The affective range (anxiety and depressive symptoms) and quality of life (QoL) were also assessed. Results: The PwMS group scored lower on current reasoning ability, verbal learning, visual-spatial ability, and processing speed compared with the control group. The incidence of anxiety was higher in the PwMS group but there was no statistically significant difference in depressive symptoms. No significant differences were found in cognitive variables between the two sexes, except in visual-spatial ability, where women outperformed men. PwMS with low QoL scored lower on the attention and concentration indices than those with adequate QoL. According to QoL, no significant differences were observed in reasoning, verbal learning, and visual-spatial ability. Conclusions: The present sentinel study suggests that the Omani cohort with MS tends to have lower indices of current reasoning ability, visual and spatial memory and cognitive speed compared to control subjects. Gender differences are minimal, except for visual-spatial abilities where women outperform men. Quality of life significantly affects cognitive functioning. In general, the biopsychosocial impediment appears to be significant, indicating the need for comprehensive evaluation and care in the management of MS.

In order to establish the formation patterns of the Co–Mg oxide system, samples with different Co:Mg ratios and heat treatment temperatures were synthesized and studied. Study of the sam-ples confirmed the phase transition of MgxCo2–xO4 spinels into corresponding solid solutions at 800–900 °C. The similarity of formation patterns for different compositions is shown. The rock-salt oxide in low-temperature samples is an anion-modified paracrystalline phase that forms a “true” solid solution only upon spinel decomposition. TPR profiles of decomposed Co3O4 spinel show surface Co3O4 peaks and a wide peak corresponding to well-crystallized CoO, while par-tial Co3O4 TPR up to 380 °C results in dispersed and amorphous CoO. High-temperature non-stoichiometric samples are poorly reduced, indicating their low oxygen reactivity. Spinel reoxidation after heat treatment to 1100 °C by calcination at 750 °C showed complete regenera-tion for MgCo2O4–Co3O4 samples and its absence in case of an excess of MgO relative to stoi-chiometry. Based on the data obtained, it can be concluded that the processes governing the formation of Co–Mg oxide systems are determined by both Co:Mg ratio and the heat treatment conditions, potentially providing the possibility of fine tuning for specific catalytic processes.

In 2023, residential and commercial sectors together consumed approximately 27.6% of total U.S. energy, equivalent to about 20.6 quadrillion Btu. Factoring in the electrical system energy losses, the residential sector represented approximately 19.7% of total U.S. energy consumption during that time. There were approximately 144 million housing units in the United States in 2023, which is increasing yearly. In this study, information on energy usage in the United States (U.S.) residential sector has been analyzed and then represented as energy intensities to establish benchmark data and to compare energy consumption of varying sizes and locations. First, public sources were identified, and data from these previously published sources were aggregated to determine the energy use of the residential sector within the US. Next, as part of this study, the energy data for seven houses/apartments from five different United States climate zones were collected firsthand. That data was analyzed, and the energy intensity of each home was calculated and then compared with the energy intensities of the other homes in the same states using RECS data. The energy intensity for each facility was calculated based on the actual energy bills. Finally, the study evaluated the carbon footprint associated with residential energy consumption in all 50 states to reinforce the importance of sustainable development initiatives.

Recently many medications are derived from natural substances that have a potential to fight diseases. These bioactive compounds such as curcumin (CUR) and nicotinamide (NIC) have an antioxidant, anti-inflammatory activity and boosting the immune system. Aim: This study aims to evaluate antibacterial and antimelanoma activity of CUR-NIC combination and their liposomal preparation. Method: Activity of CUR-NIC was investigated against skin infection bacteria, Staphylococcus aureus and Pseudomonas aeruginosa. The cytotoxicity assay for melanoma B16 cancer cell line using MTT and migration assays. Results: The CUR and CUR-NIC (1:1) combination and showed an inhibition zone against S. aureus of 18±0.8 mm and MIC 31.25 µg/ml compared to 16 ±0.85 and 62.5 µg/ml, respectively. The cytotoxicity assay for melanoma B16 cancer cell line revealed that the of CUR and NIC combination synergistically reduced cell proliferation with (CI< 1). Indeed, liposomal preparation showed cytotoxic effect of Lip-CUR (IC50= 31.4 ± 3.2), Lip-NIC (IC50=190 ± 7.3) and Lip-CUR-NIC (IC50 8.5 ± 0.3) while CUR showed IC50 of 9.8 ± 2.2µM and NIC (IC50 135.95 ±10.2 µM). Conclusion: synergistic effect when curcumin and nicotinamide are combined, potentially offering a more effective cancer treatment strategy.

Microbial composition across substrates in mangroves, particularly in the Middle East, remains unclear. This study characterized bacterial communities in sediment, water, Terebralia palustris snail guts, and plastic associated with Avicennia marina mangrove forests in two coastal lagoons in the Sea of Oman using 16S rDNA gene MiSeq sequencing. The genus Vibrio dominated all substrates except water, which featured unique genera Sunxiuqinia and Pseudomonas. There were significant differences in bacterial communities on different substrata, in particular plastic. Snail guts harbored the highest number of unique Operational Taxonomic Units (OTUs) in both lagoons. Plastic in the polluted Sawadi lagoon with low salinity harbored distinct genera like Vibrio, Aestuariibacter, Zunongwangia, and Jeotgalibacillus absent in Qurum lagoon with higher salinity and low pollution. Sawadi lagoon exhibited higher species diversity in sediment and plastic substrates, Qurum lagoon demonstrated lower overall species diversity. The PCA indicates that environmental factors like salinity, pH, and nutrient levels significantly influence bacterial community composition across substrates. Variations in organic matter and potential anthropogenic influences, particularly from plastics, further shape bacterial communities. This study highlights the complex microbial communities in mangrove ecosystems, emphasizing the importance of considering multiple substrates in mangrove microbial ecology studies.

The Yb/Al multilayer films exhibit excellent theoretical reflectivity in the 54-90nm wavelength range. This study attempted to incorporate 1.5% wt.% of Si impurities into Al to suppress the crystallization of Al, reduce interfacial roughness, and enhance the actual reflectivity of the prepared Yb/Al multilayer films. The internal microstructure changes of the film layers before and after Si impurity doping were investigated using GIXRR, AFM, and XRD techniques. The reflectivity of two types of multilayer films, Yb/Al(1.5wt.%Si) and Yb/Al(pure), was tested to evaluate the effect of Si impurity on the film performance.

Various wood fibres, including pine and flax, are used in wood–plastic composites (WPCs). This paper studies the effect of the lignin content on the morphological and thermal degradation and damage due to the ultraviolet (UV) aging of polypropylene/flax (PP-flax) and polypropylene/pine (PP-pine) fibres composites. Flax and pine fibres exhibited distinct densities of 1.51 and 1.47 g/cm³, respectively, potentially influenced by growth factors and varying compositions of light substances, such as hemicellulose, lignin, and impurities. The thermal decomposition mass loss increased proportionally with the percentage of lignin in the fibre. From 238°C to 390°C, the pine fibre exhibited a 72% mass loss compared to flax fibre, which showed a 54% mass loss, owing to the higher lignin content in pine fibres. Based on differential scanning calorimetry (DSC), the fibre composition affected the material melting temperature. Moreover, DSC curves revealed a higher degree of crystallinity in the case of the PP-flax biocomposite (12%) compared to pure polypropylene (9%) and PP-pine (6%). This result can be attributed to the high content of crystalline components in flax fibres, such as cellulose. Acoustic emissions analysis confirmed that the high lignin content delays degradation and mitigates the appearance of microcracks on the surface of the PP-pine biocomposite. Overall, the study provides valuable data for understanding the UV degradation phenomenon in biocomposites and highlights the influence of fibre composition on material performance.

Rice blast is the most harmful disease caused by Magnaporthe oryzae, leading to yield loss. The aim of the work is to improve resistance of rice to blast by introducing and pyramiding genes using conventional breeding technique and modern MAS analysis. Pyramiding is the combination of several resistance genes in one genotype, in this case it improves the resistance of rice to pathogens. MAS analysis revealed that 3 out of 4 studied domestic high-yielding rice cultivars (Bakanasski, Aisaule and Aru) contain 1 blast resistance gene (Pi-2). It was discovered 7 pyramidal lines with the introduction of a combination of 2 blast resistance genes (Pi-1 and Pi-ta) into 6 hybrids and 3 genes (Pi-1, Pi-33 and Pi-ta) into 1 line. Phytopathological test of local cultivars and pyramidal lines of rice showed that 3 out of 7 pyramidal lines have moderate resistance: 2 lines (F2 Bakanasski/7667 (var. vulgaris Koern.) and F2 Aisaule/7664 (var. italica Alef.)), containing 2 resistance genes (Pi-1 and Pi-ta) and 1 line – F2 Aisaule/7689 (var. zeravschanica Brsch.), carrying 3 genes (Pi-1, Pi-33 and Pi-ta), while the local cultivars Bakanasski, Aisaule and Aru are susceptible. As a result, the blast resistance of rice was improved by creating pyramidal lines. Pyramided lines can be used for germplasm exchange and in rice breeding programs to improve blast resistance in rice.

This paper presents the deformation of the joined sheet after the clinch-riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1±0.05 mm and 1.5±0.1 mm. The sheet deformation was measured before and after the joining process. The rivet was pressed in the sheets with the same dimension between the rivet axis and three sheet edges: 20, 30 and 40 mm. For fixed segments of the die, from the rivet side close to the rivet, the sheet deformation was greater than that of the area with movable segments. The movement of die sliding element caused more sheet material to flow in the space between the fixed part of the die and movable segments. Hence, the sheet deformation in these places was smaller than for the die fixed element – sheet material was less compressed. For sheets thickness 1.5 mm and width 20 mm, the bulk of the sheet was observed. For a sheets width of 20 mm, it was observed that the deformation of the upper and lower sheets in the area of the rivet is greater than for sheets width of 30 or 40 mm.

Generative artificial intelligence tools are flourishing across various sciences, particularly in the educational domain. ChatGPT, with its versions 3.5 and 4.0, stands out for its multilingual capabilities, catering to both students and educators. This research aimed to evaluate the performance differences between these versions, and importantly, to compare the accuracy of ChatGPT's responses in English versus Arabic. In our study, we presented ChatGPT with 39 chemistry problems related to 6th-7th grade curriculum, including twenty-five open questions and fourteen multiple-choice questions. Each response was categorized as accurate, partially accurate, or inaccurate. Our analysis, focused on trends across versions and languages, revealed significant enhancements in version 4.0, particularly in its ability to process Arabic. However, despite these improvements, our findings indicate that responses in English consistently outperformed those in Arabic in terms of accuracy. In light of this discrepancy, we suggest that ChatGPT either incorporates additional Arabic databases into its training regimen or develops a code that adopts the following strategy to ensure more accurate responses in science education: questions should first be translated from Arabic to English, addressed, and then retranslated into Arabic before being presented to the user. This approach takes advantage of the greater accuracy of responses in English to benefit Arabic-speaking users, and it may also improve outcomes for speakers of other languages who experience less precise answers in the fields of chemistry or science education.

Cytologic diagnosis of extra‐adrenal paraganglioma presenting as a peripancreatic mass is challenging with a high rate of diagnostic error. We present a case of a peripancreatic mass identified by radiology as a gastrointestinal stromal tumor. Endoscopic ultrasound‐guided fine needle aspiration (FNA) of the mass showed a moderately cellular tumor composed of small to medium sized neoplastic cells with round to oval nuclei arranged singly and in loose clusters. The cells were positive for neuroendocrine markers (synaptophysin and chromogranin) and negative for CD117. A diagnosis of a neoplasm with a neuroendocrine tumor (NET) was made on FNA cytology. The subsequent surgical resection of the tumor revealed peripancreatic paraganglioma with immunohistochemistry positive for synaptophysin, chromogranin, and S100. The latter delineates the sustentacular cells. Although paraganglioma is a well recognized tumor, a detailed comparison of peripancreatic paraganglioma versus pancreatic/gastrointestinal NET is still lacking.

Solar pasteurization, as a means of treating milk in remote rural areas without electrical power, is based on using solar energy to thermally inactivate pathogenic microorganisms at temperatures below the boiling point to maintain or improve milk quality. A solar milk pasteurizer of flat‐plate water‐heating glass acting as the solar collector, connected to a stainless-steel cylindrical milk vat, was constructed and evaluated in Navrongo, in the tropical savanna zone of Ghana, West Africa. The novel approach taken in this project is to integrate the solar collection and heat exchanger into a single unit using materials and fabrication techniques readily available in the developing world. The vat comprises a 1.5 mm thick stainless steel cylindrical tank, a 2.2 cm wide hot water jacket, and an outer layer of 5.0 mm thick aluminium foil insulation. Hot water produced by the collector was used for pasteurizing milk. The optimum quantity of milk that this device could pasteurize under the study conditions was 8 L. The device could pasteurize raw milk to a maximum temperature of 74 °C at 14:00 h GMT. The ambient temperature during the pasteurization ranged from 30 °C to 43 °C. The microbial analysis before and after the pasteurization was done, and the result shows that the total bacteria count before pasteurization was 6.6x10⁶ log CFU/mL per unit volume, and the total bacteria count after pasteurization was 1.0x10² log CFU/mL. By acceptable standards, the total bacteria count after pasteurization is within a safe range for consumption, and coliform counts were negative. The solar milk pasteurization system is cost-effective. Hence, it is appropriate for milk producers in arid pastoral areas without electricity to adopt the solar pasteurizer as an alternative to firewood as a fuel source for milk pasteurization. This approach can potentially create a cottage industry that may also play a crucial role as a water treatment technology that will improve the health of rural populations.

The Gulf Cooperation Council (GCC), locally known as Khaliji, is a group of six Arab nations, including Saudi Arabia, Bahrain, Kuwait, Oman, Qatar, and the United Arab Emirates (UAE). Intimate partner violence (IPV) is a significant public health concern in the GCC region, but the research that synthesized the trend has received scant attention. The present narrative review examines existing research on the prevalence and frequency of IPV among Khaliji women in GCC nations. This review synthesized studies on physical violence, sexual violence, emotional abuse, and controlling behaviors perpetrated by an intimate partner. The prevalence rates of IPV among Khaliji women are observed to be high: women reported facing different types of abuse from their partners, namely physical (7% - 71%), sexual (3.7% - 81%), financial (21.3% - 26%) and psychological (7.5% - 89%), which is a culmination of controlling behavior (36.8%), emotional (22% - 69%) and social violence (34%). The extant studies in the GCC suggest that the most endorsed IPV was psychological abuse (89%) followed by sexual violence (81%). Qualitative content analysis of the associated factors resulted in four meaningful descriptors such as demographics of the victim, sociocultural factors, socioeconomic, and perpetrator-related issues. The study on IPV is still nascent and few. The way forward will require developing culturally appropriate interventions that address unique risk factors for IPV among Khaliji populations, strengthening institutional responses, and increasing awareness and social support for the victim of IPV.

FER zeolites has a unique framework structure and acid distribution, and is widely studied as a catalyst for reactions such as n-butene skeletal isomerization and dimethyl ether carbonylation. The BAS located in the 10-MR of FER zeolites serves as the active site for the isomerization reaction of n-butene skeletal to produce isobutene. In contrast, the acid site found in the 8-MR is prone to side reactions, such as polymerization and cracking, which can adversely affect the selectivity of isobutene. This study prepared five types of FER zeolites using different method, inducing Na-form or H-form crystal seeds without organic structure directing agents (OSDAS), using pyridine alone as a template, and combining the seeds with pyridine. The differences in the structure and acid distribution of the five zeolites were investigated, as well as their catalytic performance for the the skeletal isomerization of n-Butene. Experiments and characterization results showed that under hydrothermal synthesis conditions, the FER-PY+SH zeolites synthesized by using both H-form zeolites seeds and pyridine exhibited the highest aluminum concentrations at T1 and T3 positions, along with the greatest BAS of 10-MR. This unique composition contributed to the highest selectivity of isobutene. The FER-PY+SH catalyst was continuously used for 720 hours at 350 ℃, 0.1 MPa, and n-butene mass space velocity of 2.0 h^-1 for three recycles on 2160 h. During this period, the conversion of n-butene over 39%, while the selectivity of isobutene exceeded 95%.The catalyst exhibited excellent stability and activity.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

Dry Fish is a rich source of proteins and nutrients and can be eaten in many forms. Oman is one of the important fish producers in the world and having high demand in neighboring countries for Oman’s fish. Fishery sector is considered as one of the important economic development sector in sultanate of Oman. In the fishery sector, use of technology is not up to the mark because of less awareness of technology application among Omani fishermen. Also, there is a demand for a greater number of cold storages in different regions to store fresh fishes which is not materialized yet. Similarly, there is a demand of perfect and cheap technology in Oman to dry fishes to improve the profit to the fishermen. Solar energy is abundantly available in Oman and there are high possibilities in Oman to use solar energy in domestic and industrial applications. Since the sunlight is available throughout the year, it is possible to convert in to thermal energy or electrical energy. Electricity can be produced from photovoltaic principle (PV) or indirectly with concentrated solar power. Similarly, we can use solar concentrators for many thermal applications. The solar dryer is a device which is used to dry fruits, vegetables, leaves, clothes etc. If any of the items are dried with the help of solar energy, then we can save lot of non-renewable source of energy and can help to improve economy of the country. The sun can, at least seasonally at Oman’s latitudes, provide a substantial part of the energy needed for various applications. In this work, we used solar dryer to make dry fish with high quality. Use of parabolic type concentrator to dry the fish is an effective solution which is an innovative idea to the fishermen. The temperature variation in dryer is directly proportional to the intensity of solar. The tracking mechanism is a combination of electronic and mechanical design which tracks the sun automatically. In this work, a parabolic concentrator with automatic tracking mechanism was designed and the performance analysis have been done. In the design, copper tubes are used for heat transfer and then the hot fluid is circulated in the box which is used to dry the fishes. As per the experiment, fish drying efficiency obtained from solar dryer is 77.9% and it took 3 days to dry king fish of 20kg. There are many advantages in parabolic type solar concentrators relate to the quality of dryness in the fishes and time taken to dry the fishes which are elaborately discussed in this paper. This solar dryer technology will improve green environment and also will save non-renewable sources of sultanate of Oman for longer period of time.

Fractional cointegration in time series data has been explored by several authors, but panel data applications have been largely neglected. A previous study of ours discovered that the Chen and Hurvich fractional cointegration test for time series was fairly robust to a moderate degree of heterogeneity across sections, out of the six tests considered. Therefore, this paper advances a customized version of the Chen and Hurvich methodology to detect cointegrating connections in panels with unobserved fixed effects. Specifically, we develop a test statistic that accommodates variation in the long-term cointegrating vectors and fractional cointegration parameters across observational units. The behaviour of our proposed test is examined through extensive Monte Carlo experiments under various data generating processes and circumstances. The findings reveal that our modified test performs quite well comparatively and can successfully identify fractional cointegrating relationships in panels even in the presence of idiosyncratic disturbances unique to each cross-sectional unit. Furthermore, the proposed modified test procedure established the presence of long-run equilibrium between the exchange rate and labour wage of 36 countries agricultural markets.

Inflammatory myofibroblastic tumor (IMT) is a rare soft tissue tumor of mesenchymal origin that most commonly presents in children. IMTs hold non-specific symptoms and radiological features, rendering diagnosis challenging. Presentation: We report a case of a 26-year-old man who was diagnosed at a different center with IMT of the right lower lobe. He underwent lobectomy with a positive gross margin, after which he was referred to our institution for further management, where we performed redo surgery with removal of residual tumor from the bronchial stump. The case presented here shows that interdisciplinary surgical planning is vital to ensure proper detection and successful tumor resection, while highlighting a unique case of recurrence necessitating a redo surgery.Conclusion: IMT is a rare entity in adults presenting with diverse, non-specific symptoms. IMT’s usually follow a favorable prognosis, but behavior may be unpredictable. While uncommon in adults, strong clinical suspicion is warranted. Complete surgical resection is the treatment of choice and follow up is crucial given the potential for recurrence.

Pre-diabetes is a serious health condition where blood sugar levels are higher than normal, but not high enough yet to be diagnosed as type 2 diabetes. Pre-diabetes puts one at an increased risk of developing type 2 diabetes and heart disease Methodology: A cross-sectional study was carried out on 384 patients aged 20-70 years old, attending the dental clinics to assess the risk for diabetes, using the FINDRISC questionnaire, HbA1c blood test and a periodontal examination. Results: The mean age of participants was 38.90±10.74. 32.3% were categorized as no risk, 46.6% low risk, while 19% and 2.1% moderate and high risk of developing diabetes respectively. Tests for serum HbA1c Level showed 46.1 % had normal HbA1c followed by 18.0% and 3.6 % were pre-diabetic and diabetic respectively. 19.3% of participants had periodontal pockets measuring more than 4mm and 15.9% measuring more than 6mm. Conclusion: The study has proven to be useful in identifying patients at high-risk of developing diabetes. Controlling and managing periodontal disease could be a new aspect to include in the standards for diabetes care. Dental settings could be a successful platform to carry out the screening and risk stratification of pre-diabetic patients.

Sustainable development and education in sustainable development (ESD) are crucial and interconnected topics under wide discussion today. Young adults need to be educated in how to help bring about change. Thus, the dynamic relationship between school and home is important. In education, use could be made of English language classes, especially since English is a global language that enables access to the sustainability literature and facilitates discussion in global conferences and meetings. Consequently, English as a foreign language (EFL) students could gain confidence from being able to understand and use the terminology of, for example, sustainability. In this paper, the use of competence-based language teaching (CBLT) is proposed as a means of introducing sustainability topics into EFL writing classes at a university in Saudi Arabia. Students’ competence in sustainable development is therefore considered based on their ability to write about suggested sustainable development topics, measured on a scale for five dimensions of ESD proposed by Michelsen and Fischer (2017). The results demonstrate that the students possessed competence in sustainable development and intended to participate in its implementation. Thus, recommendations are made for the stakeholders in the education sector to include sustainable development topics as an initial offering in the curricula of various specialties using the CBLT approach.

Mosquito-borne diseases (MBDs) are a group of illnesses transmitted by mosquitoes and can be caused by bacteria, viruses, or parasites. These diseases represent a significant global burden of infectious diseases, including morbidity and mortality. This systematic review delves into the multifaceted factors contributing to the spread of mosquito-borne diseases (MBDs) in the Middle East and North Africa (MENA) region. Following PRISMA guidelines, a thorough analysis of peer-reviewed articles from May 1990 to Jan 2023 was conducted, highlighting the interplay of population, environmental, disease, and mosquito factors in disease transmission and prevalence. The review incorporated 31 studies that revealed a complex relationship between various risk factors and the presence of MBDs. Significant associations were observed with age, certain occupations, environmental conditions such as rainfall and temperature, sanitation practices, specific pathogen variants, clinical symptoms, and Aedes aegypti mosquitoes. Conversely, gender, socioeconomic status, educational status, and certain sanitation-related factors showed inconsistent association with the spread of MBDs. The review underscores the need for targeted interventions, including vector control, improved sanitation, and educational campaigns to mitigate the spread of MBDs in the MENA region. This review could guide research studies to address data gaps and assist in developing effective surveillance programs in the MENA region. This work emphasizes the need for region-specific public health strategies and further research to understand and curb the burden of these diseases effectively.

Osteopetrosis incidence is less than 1:200,000 birth in most populations (Worth, 1963) . It's more common in consanguineous people as it's unusual in two members of the same family. The defined treatment for Osteopetrosis is Hematopoietic stem cell transplantation (HSCT). With a 73% five years disease-free survival in donors. The incidence of Hypertrophic pyloric stenosis is 1 in 300–900 newborns. Hypertrophic pyloric stenosis is due to hypertrophy of the smooth muscle of the pyloric sphincter. The classic age of occurrence is the first few months of life, and the classic presentation is non-bilious projectile vomiting after feeding. We reported a four family members with Osteopetrosis and Pyloric stenosis and their three cousins with Osteopetrosis, which is a very rare presentation and association.

Hypervirulent Klebsiella pneumoniae (hvKp) is a variant that has been increasingly linked to severe, life threatening infections including pyogenic liver abscess and bloodstream infections. HvKp belonging to the capsular serotypes K1 and K2 have been reported worldwide, however very scarce studies are available on the their genomics and virulence. In the current study we report four hypermucoviscous hvKp ESBL clinical strains of capsular serotype K1 and K2 isolated from pus and urine of critically ill patients in tertiary care hospitals in Oman. These strains belong to diverse sequence types (STs) namely ST-23(K1), ST-231(K2), ST-881(K2), and ST-14(K2). To study their virulence, Galleria Mellonella model and resistance to human serum killing were used. The G. mellonella model revealed that the K1/ST-23 isolate is the most virulent as 50% of the larvae died in the first day, followed by isolate K2/ST-231 for which 75% of the larvae died in the second day and isolate K2/ST-14 for which 50% of the larvae died in the second day. Resistance to human serum killing showed there was complete inhibition of bacterial growth of all four isolates by the end of the first hour and up to the third hour. For ST-23(K1), ST-231(K2), ST-881(K2), and ST-14(K2), there was a gradual decrease in the number of colonies up to the second to third hour, which indicates neutralization of bacterial cells by the serum components. However, this was followed by sudden increase of bacterial growth, indicating possible resistance of bacteria against human serum bactericidal activity. Whole genome sequencing (WGS) revealed that hvKp strains display unique genetic arrangement of k-loci. Whole genome SNP-based phylogenetic analysis revealed that these hvKp isolates are phylogenetically distinct, belonging to diverse clades and belong to different STs in comparison to global isolates. This is the first report from Oman detailing the WGS of hvKp clinical isolates and assessing their resistance and virulence genomics, which reinforce our understanding of their epidemiology and dissemination in clinical settings.