Steam boiler has a significant role in the industrial sector. The failure in boiler tubes significantly reduces the availability of the plant. Furthermore, deposits on the inner tube wall contribute to such failure by changing the thermal resistance of the wall, which causes a significant increase in the tube wall's temperature and, consequently, lower allowable stress. The presented thermal-fluid model is developed for the water tube. The model is implemented using ANSYS FLUENT to estimate the wall maximum water tube wall temperature considering the deposits layer and then determine the minimum thickness of the tube wall via ASME standards to assure safe operation. The model is verified via a mesh independence test. The minimum tube thickness is recommended and justified given the thermo-mechanical performance of the water tubes at several operating loads of 50, 75, and 100 %. These loads are implemented by different convective heat transfer coefficients of flue gases under different deposit thicknesses, thermal conductivity, and flue gas temperature. The present work contributes to the literature by recommending the minimum thickness of the water wall tubes and highlighting the thermo-mechanical effect of the deposits on water tube resilience under different operating conditions.

In an attempt to improve the quality of the agricultural drain in Egypt for its reuse again in the irrigation, low cost solution such as sand filter along with/ without other filtration media have been used in this research, As a result of that, pilot plant of sand filter mixed with other filtration media was tested for its ability to improve the sand performance in removing the suspended solids and organic matters from agricultural drain water of the Belbeis drain (in Sharkia governorate in Egypt). Only sand compared with sand with sponge and sand with Liyan Nanfang activated carbon (L.N.A.C) have been tested to find the optimum mixing sand/ medium ratio &optimum infiltration rate. The work has been done on four runs. It was found that sand mixed with sponge gave the best removal efficiency compared to that of the sand only and the sand mixed with L.N.A.C. The results presented that the concentration of CODt, CODsol and TSS was reduced from 125, 47 and 162 mg/l to 44, 34 and 28 mg/l respectively at optimum infiltration rate of 2 m³/m²/d for sand mixed with sponge.

Copper is a heavy metal used in many industries and known for its negative impacts on the environment and human’s health. A novel structured metal organic framework (MOF) was used for copper adsorption for this work. SEM, EDAX, XRD and FTIR were done to confirm the structure of MOF prepared. MOF of 0.05 gm was used to examine its ability in Cu+ 2 removals with different initial concentrations of Cu+2 and pH values (5, 7 and 9). The prepared MOF was able to achieve Cu removal with 94.6%, 93%, 91.5%, and 92.5 % for the initial concentrations of 5, 10, 15, and 20 ppm respectively. It also performed very well for pH 5 and 7 with average removal ranging from 93.9%-95% for pH 5 and 7 for the initial concentrations of 5, 10, and 15 respectively which indicate that the prepared MOF is of high ability in Cu+ 2 removal.

The transition to sustainable energy systems in the Middle East and North Africa (MENA) region addresses critical challenges of environmental protection, energy security, and socio-economic resilience. Using neo-institutional theory, this paper examines the intricate relationship between formal and informal institutions and their significant impact on the region’s energy transition. Despite the MENA region’s abundant renewable energy resources, numerous institutional barriers, such as governance inefficiencies, regulatory inconsistencies, and entrenched socio-cultural norms, significantly hinder this transition. Through a review of existing literature, this study presents a comprehensive analytical framework designed to overcome these barriers, with a focus on the Just and Sustainable Energy Transition model. This strategic model emphasizes equity, sustainability, and inclusive governance as pillars for reform. The study offers detailed recommendations for institutional change and underscores the importance of collaborative efforts among governments, industry stakeholders, and international partners to unlock the MENA region’s renewable energy potential, advance global sustainability goals, and ensure a more secure and resilient energy future.

Under Egyptian soil conditions, when phosphorus fertilizers were applied to the soil, it gets fixed and converts to unavailable form, leading to low solubility for the plant. This study were fulfilled on sweet potato (cv. Beauregard) under undesirable soil properties (CaCO3 10.8 vs 11.3%) using Bacillus megaterium DSM 2894 strain under different five mono calcium phosphate (CSP) levels [(69(CSP20); 138(CSP40); 207 (CSP60); 276 (CSP80) and 345 ((CSP100) kg ha-1 of calcium superphosphate (CSP)] to arise the potential efficiency of some nutrients uptake and decease the applied total amount of CSP in 2019 and 2020 seasons. The results mentioned that highest values were obtained by inoculated plants with DSM2894 strain under 20, 60 and 100% of CSP for all studied nutrients content in both seasons, except Mn content in the 2019. Also, inoculated plants with DSM2894 under previous treatments for all tuberous root nutrients content, except Fe and Zn contents in both seasons, in addition protein and anti-radical power and total yield. Statistically, leaf nutrients uptake and tuberous root content were highly significant affected by DSM and CSP combination. Appling of phosphorus fertilizer with DSM2894 mixture was gave the best values as compared with phosphorus fertilizer or DSM2894, individually.

The utilization of fuel cells (FC) in automotive technology has experienced significant growth in recent years. Fuel cell hybrid electric vehicles (FCHEVs) are powered by a combination of fuel cells, batteries, or/and ultracapacitors (UCs). By integrating power converters with these power sources, the FCHEV system can overcome the limitations of using them separately. The performance of an FCHEV is influenced by the efficiency of the power electronics converter controller, as well as the technical efficiency of the power sources. FCHEVs need intricate energy management systems (EMSs) to function effectively. Poor EMS can lead to low efficiency and accelerated fuel cell and battery degradation. The literature discussed various types of EMSs, such as equivalent consumption minimization strategy, classical PI controller, fuzzy logic controller, and Mutative Fuzzy Logic Controller (MFLC). However, comparing different EMSs can be challenging due to the varying vehicle and system parameters, which might lead to false claims being made regarding system performance. This research aims to categorize and discuss the various topologies of FCHEVs, highlighting their pros and cons, and comparing several EMSs based on performance metrics such as State of Charge (SOC) and FC deterioration.

Purpose: When it comes to improving citizen service delivery standard and processes, or broadly, management in government (MIG), many reform programs and improvement efforts are ongoing across different ministries, departments, and agencies. This paper is part of a larger empirical research where we are interested to know what those programs and projects are, and how they are doing, and what the gaps are. Design/methodology/approach: Analyzing the publicly available data on the government portal and donors’ website, this article provides an overall idea of current reforms in various places of government. In parallel, field research was conducted through visiting agency offices, observing office environment and mechanisms, and interviewing public managers who are working at district and sub-district level offices of directorates or agencies.Findings: As a trend, state-led development process and the traditional mode of administration have moved to New Public Management based quality and performance approach. All donors have their own strategy framework document like ‘Country Assistance strategy’, ‘Country Operations and Business Plan’, Logical Framework Document, Focus or Priority Streams, etc. Many of the projects are sectoral and agency or ministry specific and have an inherent limitations, due to ‘cadre’ based organizational structural arrangement. So, it is common ‘not to own the projects’, rather ‘using the fund as much as possible anyway within the given project duration’. When the fund ends, implementing units, either government or NGOs, abandon the projects. That is why many projects are actually half done without significant and sustained direction.Originality/value: We can conclude that the typical ‘top-down’ or ‘trickle down’ conception is still dominant in design and implementation of reforms programs and service quality efforts. So, how to reach systemically at the bottom where public managers provide services to citizens, needs even more deliberation.

We study the brain segmentation by dividing the brain into multiple tissues. Given possible brain segmentation by deep, machine learning can be efficiently exploited to expedite the segmentation process in the clinical practice. To accomplish segmentation process, a MRI and tissues transfer using generative adversarial networks is proposed. Given the better result, we propose the transfer model using GAN. For the case of the brain tissues, white matter (WM), gray matter (GM) and cerebrospinal fluid (CSF) are segmented. Empirical results show that this proposed model significantly improved segmentation results compared to the stat-of-the-art results. Furthermore, a dice coefficient (DC) metric is used to evaluate the model performance.

Currently, face recognition technologies are the most widely used methods for verifying 1an individual’s identity. Nevertheless, it has increased in popularity, raising concerns about face spoofing attacks, in which a photo or video of an authorized person’s face is used to get access to services. Based on a combination of Background Subtraction (BS) and Convolutional Neural Networks (CNN), as well as an ensemble of classifiers, we propose an efficient and more robust face spoof detection algorithm. This algorithm includes a Fully Connected (FC) classifier with a Majority Vote (MV) algorithm, which uses different face spoof attacks (e.g., printed photo and replayed video). By including a majority vote to determine whether the input video is genuine or not, the proposed method significantly enhances the performance of the Face Anti-Spoofing (FAS) system. For evaluation, we considered the MSU MFSD, REPLAY-ATTACK, and CASIA-FASD databases. The obtained results by our proposed approach are better than those obtained by state of the art methods. On the REPLAY-ATTACK database, we were able to attain a Half Total Error Rate (HTER) of 0.62% and an Equal Error Rate (EER) of 0.58%. It was possible to attain an EER of 0% on both the CASIA-FASD and the MSU FAS databases.

Purpose: To evaluate the efficacy and survival rates of same session ab interno trabeculectomy with the trabectome and Ahmed glaucoma valve implant (AT) in comparison to the Ahmed glaucoma valve alone (A). Method: A total of 107 eyes undergoing primary glaucoma surgery were enrolled in this retrospective comparative case series, including 48 eyes which underwent AT and 59 eyes which received A alone. Participants were identified using the procedural terminology codes, and their medical records were reviewed. The primary outcome measure was surgical success, defined as intraocular pressure (IOP) > 5 mmHg, ≤ 21 mmHg, and IOP reduction ≥ 20% from baseline at two consecutive visits after three months, no reoperation for glaucoma. Secondary outcome measures were IOP, the number of glaucoma medications, incidence of a hypertensive phase, and best corrected visual acuity (BCVA). Results: The cumulative probability of success at one year was 70% in AT, and 65% in A (p=0.85). IOP decreased significantly from 26.6 ± 10.1 mmHg at baseline to 14.7 ± 3.3 mmHg at the final follow-up in AT (p= 0.001). The corresponding numbers for A were 28.8 ± 10.2 and 16.7 ± 4.9, respectively (p= 0.001). The final IOP was significantly lower in AT (p= 0.022). The number of medications at baseline was comparable in both groups (2.6 ± 1.2 in AT and 2.5 ± 1.3 in A, p=0.851). Corresponding number at 1 year visit was 1.2±2 in AT and 2.8±1.8 in A (p=0.001). The incidence of a hypertensive phase was 18.7% in AT and 35.5% in A (p=0.05). HP resolved in only 30% of eyes. The criteria for HP resolution were fulfilled in 9 eyes (30%). There was no difference in the rate of resolution of the hypertensive phase between AT and A (33.3% and 28.5%, respectively, p=0.67). Conclusion: Ahmed glaucoma valve implant with same session trabectome surgery significantly decreased the rate of the hypertensive phase and postoperative IOP as well as the number of glaucoma medications.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

A relevant aspect in the epidemiology of Tegumentary Leishmaniasis (TL) is the Leishmania parasites carrying a viral endosymbiont Leishmania RNA Virus 1 (LRV1), a dsRNA virus. Leishmania parasites carrying LRV1 are prone to causing more severe TL symptoms, increasing the likelihood of unfavorable clinical outcomes. LRV1 has been observed in cultured strains of five L. (Viannia) species, and host specificity was suggested when studying LRV1 from L. braziliensis and L. guyanensis strains. The coevolution hypothesis of LRV1 and Leishmania was based on phylogenetic analyses, implying an association between LRV1 genotypes, Leishmania species, and their geographic origins. This study aimed to investigate LRV1 specificity to Leishmania (Viannia) species hosts by analyzing LRV1 from L. (Viannia) species. To this end, LRV1 was screened in L. (Viannia) species other than L. braziliensis or L. guyanensis, and it was detected in 11 out of 15 L. naiffi and in 2 out of 4 L. shawi. Phylogenetic analyses based on partial LRV1 genomic sequencing supported the hypothesis of host specificity, as LRV1 clustered according to their respective Leishmania species hosts. These findings underscore the importance of investigating Leishmania and LRV1 coevolution and its impact on Leishmania (Viannia) species dispersion and pathogenesis in the American Continent.

Preventive Maintenance (PM) is a periodic maintenance strategy, which has great results for devices in extending their life, increasing productivity, and most importantly, help avoid unexpected breakdowns and their costly consequence. A preventive maintenance scheduling (PMS) is determining the time for carrying out PM, and it represents a sensitive issue in terms of impact on production if the time for the PM process is not optimally distributed. In this study, hybrid heuristic methods were used to solve the PMS problem, as genetic algorithm and Tabu research were adopted. The optimal solution was reached in a short time compared to previous studies in which optimal methods were used, integer programming and nonlinear integer programming. Also, sensitivity analysis was applied to measure the robustness and strength of the method used, where an optimal solution was obtained for all experiments and in record time. This method can be used for power plants in privet or public sectors, to generate an optimal PMS, to save money, and to avoid water or electricity cuts.

Objectives: There are limited data regarding the efficacy of methylprednisolone in patients with acute respiratory distress syndrome (ARDS) due to coronavirus disease 2019 (COVID-19) requiring invasive mechanical ventilation. We aimed to determine whether methylprednisolone increases the number of ventilator-free days (VFDs) among these patients. Design: Retrospective single-center study Setting: Intensive care unit Patients: All patients with ARDS due to confirmed SARS-CoV-2 infection and requiring invasive mechanical ventilation between 1 March and 29 May 2020 were included Interventions: None Measurements and Main Results: The primary outcome was ventilator-free days (VFDs) during the first 28 days, defined as being alive and free from mechanical ventilation. The primary outcome was analyzed with competing-risks regression based on Fine and Gray’s proportional subhazards model. Death before day 28 was considered to be the competing event. A total of 77 patients met the inclusion criteria. Thirty-two patients (41.6%) received methylprednisolone. The median dose was 1 mg.kg-1 (IQR: 1-1.3 mg.kg-1) and median duration of 5 days (IQR:5-7 days). Patients who received methylprednisolone had a mean 18.8 VFDs (95% CI, 16.6-20.9) during the first 28 days vs. 14.2 VFDs (95% CI, 12.6-16.7) in patients who did not receive methylprednisolone (difference, 4.61; 95% CI, 1.10-8.12; P = 0.001). In the multivariable competing-risks regression analysis and after adjusting for potential confounders (ventilator settings, prone position, organ failure support, severity of the disease, tocilizumab, and inflammatory markers), methylprednisolone was independently associated with a higher number of VFDs (subhazards ratio: 0.10, 95%CI: 0.02-0.45; p=0.003). Hospital mortality did not differ between the two groups (31.2% vs. 28.9%, p=0.82). Hospital length of stay was significantly shorter in the methylprednisolone group (24 days [IQR:15-41 days] vs. 37 days [IQR:23-52 days], p=0.046). The incidence of positive blood cultures was higher in patients who received methylprednisolone (37.5% vs. 17.8%, p=0.052). However, 91% of patients who received methylprednisolone also received tocilizumab. The number of days with hyperglycemia was similar in the two groups. Conclusions: Methylprednisolone was independently associated with increased VFDs and shortened hospital length of stay. The combination of methylprednisolone and tocilizumab was associated with a higher rate of positive blood cultures. Further trials are needed to evaluate the benefits and safety of methylprednisolone in moderate or severe COVID-19 ARDS.

Background: We aimed to study the frequency, management, and outcomes of patients with blunt pancreatic trauma. Methods: We reviewed the medical records for all patients admitted with pancreatic injuries between 2011 and 2017 at the only level 1 trauma center in the country. Results: There were 71 patients admitted with pancreatic trauma (0.6% of trauma admissions and 3.4% of abdominal injury admissions) with a mean age of 31 years. Sixty-two patients had pancreatic injury grade I-II and 9 had grade III-IV. Thirty-eight percent had GCS <9 and 73% had ISS >16. The level of pancreatic enzymes was significantly proportional to the grade of injury. Over half of patients required a laparotomy, of them 12 patients had an intervention on the pancreas. Eight patients developed complications related to pancreatic injuries ranging from pancreatitis to pancreatico-cutaneous fistula while 35% developed hemorrhagic shock. Mortality was 31% and regardless of the grade of injury, the mortality was associated with high ISS, low GCS and presence of hemorrhagic shock. Conclusion: Pancreatic injuries following blunt trauma are rare and the injured subjects are usually young male. However, most injuries are of low-grade severity. This study shows that shock, higher ISS and lower GCS are associated with worse in-hospital out-comes. Non-operative management may suffice in patients with lower grade injuries, which may not be the case in patients with higher grade injuries unless carefully selected

A comparative efficacy of apathogenic genotype I (V4) and lentogenic genotype II (LaSota) strains of live Newcastle disease virus (NDV) vaccines was done following vaccination with pathogen-associated molecular pattern (PAMP) H9N2 avian influenza vaccine and challenge with velogenic NDV genotype VII.1.1 (vNDV-VII.1.1). Eight groups (Gs) of day-old chicks were used (n=25). Groups 1-4 received a single dose of PAMP-H9N2 subcutaneously, while Gs (1, 5) and (2, 6) received eye drops of V4 and LaSota respectively as twice doses. All Gs except 4 and 8 were intramuscularly challenged with vNDV-VII.1.1 at 28th days of age. No signs were detected in Gs 1, 5, 4, and 8. The mortality rates were 0% in Gs 1, 4, 5, and 8; 40% in G2; 46.66% in G6; and 100% in Gs 3 and 7. Lesions were recorded as minimal in Gs 1 and 5, but mild to moderate in Gs 2 and 6. The lowest significant viral shedding was detected in Gs 1, 2, and 5. In conclusion, two successive vaccinations of broilers with a live V4 NDV vaccine provided a higher protection against vNDV-VII.1.1 challenge than LaSota. Besides, PAMP-H9N2 with live NDV vaccines induced more protection than live vaccine alone.

Segmentation is an important step in medical imaging. In particular, machine learning, especially deep learning, has been widely used to efficiently improve and speed up the segmentation process in clinical practice. Despite the acceptable segmentation results of multi-stage models, little attention was paid to the use of deep learning algorithms for brain image segmentation, which could be due to the lack of training data. Therefore, in this paper, we propose a Generative Adversarial Network (GAN) model that performs transfer learning to segment MRI brain images.Our model enables the generation of more labeled brain images from existing labeled and unlabeled images. Our segmentation targets brain tissue images, including white matter (WM), gray matter (GM), and cerebrospinal fluid (CSF). We evaluate the performance of our GAN model using a commonly used evaluation metric, which is Dice Coefficient (DC). Our experimental results reveal that our proposed model significantly improves segmentation results compared to the standard GAN model. We observe that our model is 2.1–10.83 minutes faster than stat-of-the-art-models.

Background Homologous recombination deficiency (HRD) evolved into a major diagnostic marker in high grade ovarian cancer (HGOC) predicting the response to poly (Adenosine diphosphate-ribose) polymerase inhibitors (PARPi) and also platinum-based therapy. In addition to HRD, the type of peritoneal tumor spread influences treatment response and patient survival; miliary type tumor spread has poorer predicted outcome than non-miliary type tumor spread. Methods Known methods for HRD assessment were adapted for our technical requirements and the Predictive-value Integrated Genomic Instability Score (PIGIS) for HRD assessment evolved as an outcome. PIGIS was validated in HGOC samples from 122 patients. We used PIGIS to analyze whether the type of tumor spread correlated with HRD status and whether this had an impact on survival. Results We demonstrated that PIGIS can discriminate HRD positive from HRD negative samples. Tumors with miliary tumor spread are HRD negative and have a very bad prognosis with a progression free survival (PFS) of 15.6 months and an overall survival (OS) of 3.9 years. However, HRD negative non-miliary spreading tumors in our cohort had a much better prognosis (PFS 35.4 months, OS 8.9 years), similar to HRD positive tumors (PFS 34.7 months, OS 8.9 years). Conclusions Our results indicate that in a predominantly PARPi naïve cohort the type of tumor spread might be a better predictor of response to platinum sensitivity than HRD. It remains to be determined, whether this also applies for sensitivity to PARPi.

This hypothesis demonstrates that the efficiency of Loop-Mediated Isothermal Amplification (LAMP) for nucleic acid detection can be positively influenced by preconcentration of microbial cells onto hydrophobic paper surfaces. The mechanism of this model is based on the high attraction of microbes towards hydrophobic surfaces. Extensive studies have demonstrated that hydrophobic surfaces exhibit enhanced bacterial and fungal adhesion. The preconcentration approach by exploiting this inherent affinity of hydrophobic paper substrates enables the adherence of a greater number of target cells, resulting in a higher concentration of target templates for amplification directly from urine samples. In contrast to conventional methods, which often involve complex procedures, this approach offers a simpler, cost-effective, and user-friendly alternative. Moreover, the integration of cell adhesion, LAMP amplification, and signal readout within paper origami-based devices can provide a portable, robust, and highly efficient platform for rapid nucleic acid detection. This innovative hypothesis holds significant potential for point-of-care (POC) diagnostics and field surveillance applications. Further research and development in this field will advance the implementation of this technology, contributing to improved healthcare systems and public health outcomes.

This is a case study in the domain of public sector management or management in government, with particular reference to education as a sector as a whole. Bangladesh has shown persistent upward trends in development indicators during the last four decades. In the education sector also, many indicators improved - literacy, the female proportion of literacy, number of educational institutions, etc. Quantity wise investment and indicators increased and improved at all levels and dimensions like primary, secondary, tertiary, technical, and so on. But qualitative improvement remained mysteriously low, despite government intention to increase quality of teaching, learning, and administration. This paper aimed to draw an overall picture of qualitative scenario of the education sector. Analyzing secondary sources like public media, and primary sources like citizen interactions, this qualitative study consolidated the problems of the education sector in a coherent whole. It argues that many problems of education sector are not education problems or budget problems, rather purely and simply ‘management’ problems, and so, can effectively be solved with basic but thorough understanding of the basic technicalities of management as a discipline.

Groove pancreatitis represents a chronic focal form of pancreatitis affecting the zone between the pancreatic head and the duodenal „C” loop, known as the groove area. This is a rare condition that affects the pancreatic periampullary part, including the duodenum and the common bile duct, associated usually with long-term alcohol and tobacco misuse and being more frequent in men than in women. The most common clinical symptoms of groove pancreatitis include weight loss, acute abdominal pain, nausea, and jaundice. This report is about a 66 year old woman with a history of heavy smoking, presenting with weight loss, nausea, and upper abdominal pain. Contrast enhanced computed tomography revealed the existence of a chronic pancreatitis as well as the dilatation of the main pancreatic duct, a cyst of the pancreatic head and enlargement of the biliary tract. Conservatory treatment was initiated but with no improvement of symptoms. Since there was no indication for endoscopic retrograde cholangiopancreatography, we decided to perform a pancreatoduodenectomy, as surgery appears to be the single effective treatment.

Parkinson’s disease (PD) is a neurodegenerative disease that progresses with increasing age and some of its major symptoms include tremor, postural and movement related difficulties. Till date, the treatment of PD remains a challenge because available drugs only treat the symptoms of the disease or possess serious side effects. In light of this, new treatment options are needed, hence this study investigates the neuroprotective effects of an organic Boophone haemanthoides extract (BHE) and its bioactive compounds using an in vitro model of PD involving the toxin 1-methyl-4-phenylpyridinium (MPP+) and SH-SY5Y neuroblastoma cells. A total of seven compounds were isolated from BHE viz: distichamine (1), 1α,3α-diacetylnerbowdine (2), hippadine (3), stigmast-4-ene-3, 6-dione (4), cholest-4-en-3-one (5), tyrosol (6), and 3-hydroxy-1-(4`-hydroxyphenyl)-1-propanone (7). Six compounds (1, 2, 4, 5, 6, 7) were investigated and five showed neuroprotection alongside the BHE. This study gives insight into the bioactivity of the non-alkaloidal constituents of Amaryllidaceae since the isolated compounds and the BHE showed improved cell viability, increased ATP generation in the cells as well as inhibition of MPP+-induced apoptosis. Together, these findings support the claim that the Amaryllidaceae plant family could be a potential reserve of bioactive compounds for the discovery of neuroprotective agents.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

This paper deals with experimental study of the influence of conductive (Fe₃O₄) and insulating (Al₂O₃) nanostructured particles at various concentrations on the dielectric strength of transformer mineral oil. The method of preparation and characterization of these nanofluids (NFs) through the measurements of zeta potential, the real and imaginary parts of dielectric constant as well as the concentration and size of nanoparticles using Scanning Electron Microscope (SEM) images of nanoparticles powders and Dispersive x-ray Spectroscopy (EDS) analysis are presented. Experimental findings reveal that these two types of nanoparticles materials significantly improve AC breakdown voltage and the magnitude of this improvement depends on the concentration, size and nature (material) of nanoparticles. For a given type of nanoparticles, the effect is more marked with the smallest nanoparticles. The conductive nanoparticles offer higher enhancement of dielectric strength compared with insulating nanoparticles based nanofluids. With Fe₃O₄, the breakdown voltage (BDV) can exceed twice that of mineral oil and it increases by more than 76% with Al₂O₃. The physicochemical mechanisms implicated in this improvement are discussed.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

High hopes were associated with the new anti-angiogenic medicament, bevacizumab, which due to the possibility of binding to isoform A of vascular endothelial growth factor (VEGF), inhibited the creation of new blood vessels. However, not only blood vessels are responsible for the tumor cells' spread. During the process of tumor growth, lymphangiogenesis is mediated by other isoforms of the VEGF family, specifically VEGF-C and VEGF-D, which are independent of the bevacizumab action. Therefore, based on the mechanism of bevacizumab action and the processes of angio- and lymphangiogenesis, we formed three hypotheses: 1) if the lymph nodes in the primary ovarian cancers are metastatic, the outcome of bevacizumab treatment is worsened; 2) concerning the second-line treatment, bevacizumab will act in a weakened manner if the recurrence occurs in lymph nodes compared to local recurrences; 3) patients treated by bevacizumab are more likely to have recurrences in lymph nodes. These hypotheses raise the issue of the existing gap of knowledge, which concerns the effect of bevacizumab on the metastatic lymph nodes.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

AI is leveraging all aspects of life. Medical services are not untouched. Especially in the field of medical image processing and diagnosis. Big IT and Biotechnology companies are investing millions of dollars in medical and AI research. The recent outbreak of SARS COV-2 gave us a unique opportunity to study for a non interventional and sustainable AI solution. Lung disease remains a major healthcare challenge with high morbidity and mortality worldwide. The predominant lung disease was lung cancer. Until recently, the world has witnessed the global pandemic of COVID19, the Novel coronavirus outbreak. We have experienced how viral infection of lung and heart claimed thousands of lives worldwide. With the unprecedented advancement of Artificial Intelligence in recent years, Machine learning can be used to easily detect and classify medical imagery. It is much faster and most of the time more accurate than human radiologists. Once implemented, it is more cost-effective and time-saving. In our study, we evaluated the efficacy of Microsoft Cognitive Service to detect and classify COVID19 induced pneumonia from other Viral/Bacterial pneumonia based on X-Ray and CT images. We wanted to assess the implication and accuracy of the Automated ML-based Rapid Application Development (RAD) environment in the field of Medical Image diagnosis. This study will better equip us to respond with an ML-based diagnostic Decision Support System(DSS) for a Pandemic situation like COVID19. After optimization, the trained network achieved 96.8% Average Precision which was implemented as a Web Application for consumption. However, the same trained network did not perform like Web Application when ported to Smartphone for Real-time inference, which was our main interest of study. The authors believe, there is scope for further study on this issue. One of the main goals of this study was to develop and evaluate the performance of AI-powered Smartphone-based Real-time Applications. Facilitating primary diagnostic services in less equipped and understaffed rural healthcare centers of the world with unreliable internet service.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

Aim: This research is aimed at examining the cost-effectiveness of olanzapine versus risperidone in dementia patients with behavioural and psychological symptoms in Thailand. Methods: An existing Markov model based on a critical review through the comprehensive literature search and a justification for the most appropriate model for a Thai setting was adapted to simulate the disease progression of patients with dementia with behavioural disturbances until their need for full-time care (FTC). The time to the FTC state was estimated by a predictive equation developed by Rive et al. (2010). The model was conducted to assess the expected costs and outcomes associated with olanzapine compared with risperidone for Thai patients with BPSD aged 60 years and above. This model performed over a five-year time horizon with a one-month cycle length based on a societal perspective. The incremental cost-effectiveness ratio was used as the estimated outcome. Sensitivity analyses were also conducted to demonstrate the robustness of the results. Results: Over 5 years, olanzapine was found to be a cost-effective therapeutic option for the treatment of behaviourally disturbed patients with dementia compared with risperidone, in Thailand from a societal perspective (ICER < THB 160,000). The model underwent extensive sensitivity analyses, which also confirmed that olanzapine was the dominant strategy following the base-case findings. Conclusions: By comparison with risperidone, the model suggests that olanzapine can be regarded as a cost-effective therapeutic strategy for the management of patients with behavioural and psychological symptoms in Thailand.

Background and Objectives: In the current Covid-19 pandemic, children below the age of 12 could manifest Covid-19 symptoms and serve as a reservoir for the virus in the community. The present study was conducted to evaluate the reactogenicity, and immunogenicity of BBIBP-CorV, prior to involving this age group in the vaccination program in the kingdom of Bahrain. Subjects and Methods: The study included 582 children from 3 to 12 years old of Bahraini and non-Bahraini nationality, all of which contributed to the reactogenicity study. Of those, 401 contributed to the immunogenicity study. All children received 2 doses of BBIBP-CorV inactivated virus 3 weeks apart. To assess reactogenicity, children were followed up for 5 weeks to evaluate any vaccine-related adverse events (AE). To assess immunogenicity, blood was collected on day 0 and day 35 to assess antibody titer against S, N, and neutralizing antibody. Results: Of the 582 participants, (45.4%) were female, (54.61%) were male, with 49% in 9-12 age group. Of the 401 children contributing to the immunogenicity study, 274 (68.3%) had no prior exposure to Covid-19. The overall incidence of AE was 27.7%. No significant difference was found among different age groups. The most frequent AE was local (at the injection site) and occurred in 16% of children, followed by fever in 9.3%. No serious adverse events were reported. The Seroconversion rate was 100% among children with no prior exposure to Covid-19. Children with previous Covid-19 exposure had higher averages of anti-S (2379 U/ml compared to 409.1), anti-N (177.6 U/ml compared to 30.9) and neutralizing antibody (93.7 U/ml compared to 77.1) than children with no prior exposure at day 35. Conclusions: Two doses of COVID-19 BBIBP-CorV on the subjects aged between 3 to 12 has good safety and tolerance and can induce an effective immune response and neutralizing antibody titer.

The broad emission bump in the electromagnetic spectra observed following the detection of gravitational waves created during the kilonova event of merger of two neutron stars in August 2017, GW170817, has been linked to the heavy elements of lanthanides (Z=57-71), and a new understanding of creation of heavy elements in the r-process. The initial spectral emission bump has a wavelength range of 3000 - 7000 \AA, thus covering the region of ultraviolet (UV) to optical (O) wavelengths, and is similar to those seen for lanthanides. Most lanthanides have large number of closely lying energy levels which introduce extensive sets of radiative transitions which often form broad region of lines of significant strength. The current study explores these broad features through photoabsorption spectroscopy of 25 lanthanides ions, Ho I-III, Er I-IV, Tm I-V, Yb I-VI and Lu I-VII. With excitations only to a few orbitals up beyond the ground configurations, we find most of these ions cover large number of bound levels with open $4f$ orbital and produce tens to about hundred thousands lines that may form one or multiple broad features in X-ray to UV, O, and infrared (IR) regions. Spectrum of each of 25 ions is presented indicating presence, shape and wavelength region of the features. Accuracy of atomic data to interpret the merger spectra has been a outstanding problem. The present study aims at providing improved atomic data for energies and transition parameters obtained using relativistic Breit-Pauli approximation implemented in the atomic structure code SUPERSTRUCTURE. The present data have been benchmarked with available experimental data for energies and transition parameters. The study finds that number of ions under the present study are possible contributors of the emission bump of GW170817. All atomic data will be made available online at NORAD-Atomic-Data database.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of simulation and statistical results of EO with other optimization techniques showed that EO is more effective and superior.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus 13 voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ 14 constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources 15 on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar 16 PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed 17 using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of 18 simulation and statistical results of EO with other optimization techniques showed that EO is more effective 19 and superior.

The prevalence of autism in children in the world is estimated as one per 62 children, higher levels reported in some countries. These children experience significant problems with the development of social, behavioural and verbal and non-verbal communication skills. The skills impairment levels varies from an individual to another and that made teaching autistics a challenge for caregivers such as teachers and relatives. Hence, there are quite a number of frameworks of a software learning systems which focus on gaining the children’s attention using representational visual illustration as a learning method instead of the textual form. However, majority of these tools are lacking the personalisation ability to suite everyone in the spectrum. Assistive technology offers an alternative way to attract children with autism. Therefore, this research is proposing an Adaptive Content Management Learning System (ACMLS) model to assist caregivers to produce, design and fine-tune or customise the learning materials appropriately so that the system interface and the materials are suitable for every individual in the spectrum according to each child personal profile aiming to make learning attractive and to contribute in improving their social, communication and behavioural skills and nonetheless, their attention level to the delivered educational topics. The ACMLS model design adopts four main components which are: (1) Design component: which covers the visual design, design principles and the mental model of the children with autism. (2) Technology component: which covers the assistive technology tools and the architecture of the ACMLS system. (3) Education component: Which covers the learning objectives, styles, strategies, methods and the cognitive model. (4) Participants component: which covers the main participants who’re playing a role in the ACMLS model such as: caregivers and children with autism.

The prevalence of autism in children in the world is estimated as one per 62 children, higher levels reported in some countries. These children experience significant problems with the development of social, behavioural and verbal and non-verbal communication skills. The skills impairment levels varies from an individual to another and that made teaching autistics a challenge for caregivers such as teachers and relatives. Hence, there are quite a number of frameworks of a software learning systems which focus on gaining the children’s attention using representational visual illustration as a learning method instead of the textual form. However, majority of these tools are lacking the personalisation ability to suite everyone in the spectrum. Assistive technology offers an alternative way to attract children with autism to use. Therefore, this research is proposing Autism Content Management Learning System (ACMLS) Framework to assist caregivers to produce, design and fine-tune or customise the learning materials appropriately so that the system interface and the materials are suitable for every individual in the spectrum according to each child personal profile aiming to make learning attractive and to contribute in improving their social, communication and behavioural skills and nonetheless, their attention level to the delivered educational topics. The ACMLS framework design adopts four main components which are: (1) Design component: which covers the visual design, design principles and the mental model of the children with autism. (2) Technology component: which covers the assistive technology tools and the architecture of the ACMLS system. (3) Education component: Which covers the learning objectives, styles, strategies, methods and the cognitive model. (4) Participants component: which covers the main participants who’re playing a role in the ACMLS framework such as: caregivers and children with autism.

In recent years, semantic communication has received significant attention from both academia and industry, driven by the growing demands for ultra-low latency and high-throughput capabilities in emerging intelligent services. Nonetheless, a comprehensive and effective theoretical framework for semantic communication has yet to be established. In particular, finding the fundamental limits of semantic communication, exploring the capabilities of semantic-aware networks, or utilizing theoretical guidance for deep learning in semantic communication are very important yet still unresolved issues. In general, the mathematical theory of semantic communication and the mathematical representation of semantics are referred to as semantic information theory. In this paper, we introduce the pertinent advancements in semantic information theory. Grounded in the foundational work of Claude Shannon, we present the latest developments in semantic entropy, semantic rate-distortion, and semantic channel capacity. Additionally, we analyze some open problems in semantic information measurement and semantic coding, providing a theoretical basis for the design of a semantic communication system. Furthermore, we carefully review several mathematical theories and tools and evaluate their applicability in the context of semantic communication. Finally, we shed light on the challenges encountered in both semantic communication and semantic information theory.

The study of the impact of polyQ expansion driven proteotoxicity on cell metabolism has evi-denced NAD molecule as a central player in regulating metabolic response and cell repair in neurodegeneration. The decline in NAD intracellular levels represents a hallmark of ageing aris-ing from a dysregulation between NAD-consuming and biosynthetic enzymatic reactions in which NMNAT plays a key role. By an integrated bioanalytical and proteomic experimental design, the derangement of NAD metabolism deriving from the accumulation of polyQ-Htt protein has been analysed in Saccha-romices cerevisiae harbouring a 103Q-Htt and compared with wild-type Htt, in absence and in presence of a phenolic extract from EVOO, as a source of antioxidant bioactive compounds. Quantification of NAD and its precursors and proteomic analysis of the differential protein ex-pression has been performed by LC-DAD-MS. Chronological lifespan and NAD homeostasis was strongly impaired by proteotoxic polyQ-Htt, eliciting a depletion of NAD levels and accumulation of NaMN. In parallel a downregulation of Sirt2 expression levels has been observed. Phenolic extract administration had no meaningful ef-fects on NAD replenishment to prevent proteotoxicity. NaMN can represent a biomarker of accel-erated aging, and/or a signaling molecule for cell repair.

Recently, the application of Artificial Intelligence (AI) in many areas of life has allowed raising the efficiency of systems and converting them into smart ones, especially in the field of energy. Integrating AI with power systems allows electrical grids to be smart enough to predict the future load, which is known as Intelligent Load Forecasting (ILF). Hence, suitable decisions for power system planning and operation procedures can be taken accordingly. Moreover, ILF can play a vital role in electrical demand response, which guarantees a reliable transitioning of power systems. This paper introduces a Perfect Load Forecasting Strategy (PLFS) for predicting future load in smart electrical grids based on AI techniques. The proposed PLFS consists of two sequential phases, which are; Data Preprocessing Phase (DPP) and Load Forecasting Phase (LFP). In the former phase, input electrical load dataset is prepared before the actual forecasting takes place through two essential tasks, namely feature selection and outlier rejection. Feature selec-tion is done using Advanced Leopard Seal Optimization (ALSO) as a new natural inspired opti-mization technique, Citation: To be added by editorial staff during production. Academic Editor: Firstname Last-name Received: date Revised: date Accepted: date Published: date Copyright: © 2023 by the authors. Submitted for possible open access publication under the terms and conditions of the Creative Commons Attribution (CC BY) license (https://creativecommons.org/licenses/by/4.0/). While outlier rejection is accomplished through Interquartile Range (IQR) as a measure of statis-tical dispersion. On the other hand, actual load forecasting takes place in LFP using a new pre-dictor called; Weighted K-Nearest Neighbor (WKNN) algorithm. The proposed PLFS has been tested through excessive experiments. Results have shown that PLFS outperforms recent load forecasting techniques as it introduces the maximum prediction accuracy with the minimum root mean square error.

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

In 2023, residential and commercial sectors together consumed approximately 27.6% of total U.S. energy, equivalent to about 20.6 quadrillion Btu. Factoring in the electrical system energy losses, the residential sector represented approximately 19.7% of total U.S. energy consumption during that time. There were approximately 144 million housing units in the United States in 2023, which is increasing yearly. In this study, information on energy usage in the United States (U.S.) residential sector has been analyzed and then represented as energy intensities to establish benchmark data and to compare energy consumption of varying sizes and locations. First, public sources were identified, and data from these previously published sources were aggregated to determine the energy use of the residential sector within the US. Next, as part of this study, the energy data for seven houses/apartments from five different United States climate zones were collected firsthand. That data was analyzed, and the energy intensity of each home was calculated and then compared with the energy intensities of the other homes in the same states using RECS data. The energy intensity for each facility was calculated based on the actual energy bills. Finally, the study evaluated the carbon footprint associated with residential energy consumption in all 50 states to reinforce the importance of sustainable development initiatives.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

Image segmentation is a new challenge prob- lem in medical application. The use of medical imaging has become an integral part of research, as it allows us to see inside the human body without surgical intervention. Many researcher have studied brain segmentation. One stage method is used to segment the brain tissues. In this paper, we proposed the multi-stage generative ad- versarial network to solve the problem of information loss in the one-stage. We utilize the coarse-to-fine to improve brain segmentation using multi-stage generative adversar- ial networks (GAN). In the first stage, our model generated a coarse outline for (i) background and (ii) brain tissues. Then, in the second stage, the model generated outline for (i) white matter (WM), (ii) gray matter (GM) and (iii) cerebrospinal fluid (CSF). A good result can be achieved by fusing the coarse outline and refine outline. We conclude that our model is more efficient and accu- rate in practice for both infant and adult brain segmenta- tion. Moreover, we observe that multi-stage model is faster than prior models. To be more specific, the main goal of multi-stage model is to see the performance of the model in a few shot learning case where a few labeled data are available. For medical image, this proposed model can work in a wide range of image segmentation where the convolution neural networks and one-stage methods have failed.

In Bangladesh, family businesses play a significant role in the country's business landscape because so few private companies are set up as large-scale, non-family ownership firms. Thus, it is vital to comprehend family businesses in order to comprehend Bangladeshi company dynamics. In this paper, authors attempted to survey the existing research in the area of family business in Bangladesh. It was found that the area as a research is totally an open field and a lot of new research can be done in the said area. Although a good number of studies can be classified as focused on the SME (small and medium enterprise) domain, a major shortcoming of those SME studies is that the SMEs themselves vary greatly in terms of size, scope, and technology. Whereas most of the family businesses can be predominantly put in the SME category, the particular issue of family business and family dynamics is not very common in those studies. This paper suggests that a good amount of research or studies can be done focusing on family business constitution, family members' participation norm, recruitment and promotion norm, family business succession rules and succession planning, training for family business leadership and management, training for board and directorial supervision, and so on.

In this study, we introduce the dynamics of a Hepatitis B virus (HBV) model with the class of asymptomatic carriers and conduct a comprehensive analysis to explore its theoretical aspects and examine the crossover effect within the HBV model. To investigate the crossover behavior of the operators, we divide the study interval into two subintervals. In the first interval, the classical derivative is employed to study the qualitative properties of the proposed system, while in the second interval, we utilize the ABC fractional differential operator. Consequently, the study is initiated using the piecewise Atangana-Baleanu derivative framework for the systems. The HBV model is then analyzed to determine the existence, Hyers-Ulam (HU) stability, and disease-free equilibrium point of the model. Moreover, we showcase the application of an Adams-type predictor-corrector (PC) technique for Atangana-Baleanu derivatives and an extended Adams-Bashforth-Moulton (ABM) method for Caputo derivatives through numerical results. Subsequently, we employ computational methods to numerically solve the models and visually present the obtained outcomes using different fractional-order values. This network is designed to provide more precise information for disease modeling, considering that communities often interact with one another, and the rate of disease spread is influenced by this factor.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Seawater contamination is a global challenge due to its hazardous effects on marine organisms and human health. Twenty-three surface seawater samples were collected from Al Lith intertidal area along the Saudi Red Sea coast to evaluate the ecological risks and document the potential sources of Cr, Cd, Fe, Zn, and Pb. Contamination factor (CF), contamination degree (Cd), water quality index (WQI), and heavy metal pollution index (HPI), as well as multivariate tools were applied. The averages of HMs (μg/L) had the following order: Zn (6.616) &gt; Pb (0.284) &gt; Cd and Cr (0.268) &gt; Fe (0.197). Results of CF showed moderate contamination of seawater with Cd and low contamination for Cr, Fe, Zn, and Pb. However, 26.09% of the samples showed considerable contamination for Cd. Average Cd values revealed low contamination for HMs, while 17.39% of the samples showed moderate contamination. HPI average values indicated medium pollution for Al Lith seawater, meanwhile 13 samples reported high pollution. The higher HPI values were reported in samples characterized by higher concentration of HMs, particularly Cd and Zn. Correlation matrix and principal component analysis suggested anthropogenic sources for Pb and Zn, mostly from industrial and agricultural effluents, landfilling and domestic wastewaters, apart from their natural sources.

This study introduces a compact Raman spectrometer with a 1064 nm excitation laser coupled with a fiber probe and an inexpensive motorized stage, offering a promising alternative to widely used Raman imaging instruments with 785 nm excitation lasers. The benefits of 1064 nm excitation for biomedical applications include further suppression of fluorescence background and deeper tissue penetration. The performance of the 1064 nm instrument in detecting cancer in human bladder resectates is demonstrated. Raman images with 1064 nm excitation were collected ex vivo from 10 human tumor and non-tumor bladder specimens and the results are compared to previously published Raman images with 785 nm excitation. K-Means cluster (KMC) analysis is used after pre-processing to identify Raman signatures of control, tumor, necrosis, and lipid-rich tissues. Hierarchical cluster analysis (HCA) groups the KMC centroids of all specimens as input. The tools for data processing and hyperspectral analysis were compiled in an open source Python library called SpectraMap (SpMap). In conclusion, the 1064 nm Raman system can differentiate between tumor and non-tumor bladder tissues in a similar way to 785 nm Raman spectroscopy. These findings hold promise for future clinical hyperspectral imaging.

“Pecorino” is a typical semi-hard cheese obtained with raw or heat-treated sheep milk using procedures to valorize the raw material's chemical and microbiological properties. In the present study, using a high throughput method of 16S rRNA gene sequencing, we assessed the evolution of the microbiome composition from milk to Pecorino cheese in artisanal processes using milk from Comisana and Lacaune sheep breeds. The comparative analysis of the bacterial com-munity composition revealed significant differences in the presence and abundance of specific taxa in the milk microbiome of the Comisana and Lacaune breeds. NGS analysis also revealed differences in the curd microbiome related to dairy farming practices, which have a relevant effect on the final structure of the Pecorino-cheese microbiome.

DIEP-based breast reconstruction necessitates wide undermining at the abdominal donor-site, creating large wound areas. Flap harvesting is usually conducted using electrosurgical dissection devices. This study sought to compare the clinical outcomes in patients after using the PEAK PlasmaBlade (PPB) versus monopolar electrocautery (MPE). This retrospective cohort study included 128 patients with DIEP-based breast reconstruction. Patient characteristics as well as information on the postoperative course were collected and a comparative evaluation was conducted. The MPE group exhibited significantly (p* = 0.0324) higher abdominal drainage volume (351.11 ± 185.96 ml) compared to the PPB group (279.38 ± 183.38 ml). Subgroup analysis demonstrated that PPB significantly reduced postoperative wound fluid in patients with BMI > 30 kg/m² (p* = 0.0284), without prior neoadjuvant chemotherapy (p** = 0.0041), and among non-smokers (p = 0.0046). Furthermore, postoperative pain was significantly (p**** < 0.0001) lower in the PPB cohort. This study confirms the non-inferiority of the PEAK PlasmaBlade to conventional electrocautery for abdominal flap harvesting. The PPB demonstrated advantages, notably reduced drainage volume and lower postoperative pain levels. Recognizing patient subsets that benefit more from the PPB highlights the importance of personalized device selection based on patient characteristics.

Drosophila melanogaster serves as a important research model both for genetic investigations and for the study of metal toxicity, facilitating the elucidation of physiological mechanisms comparable to those of human organisms. In our research, we evaluated the toxicity effect resulting from exposure to various concentrations of lead and copper on the prolificity rates throughout the life cycle (egg-adult) of four genotypes of Drosophila melanogaster: wild-type (control), white, brown, and white-vestigial. During our study, the prolificity rates were examined across three repetitions under the impact of exposure to concentrations of 0.50, 1.00, 2.00, and 4.00 mM of copper (CuSO₄) and lead (Pb(C₂H₃O₂₎₂). Prolificity rates throughout the life cycle exhibited variations as a direct consequence of genetic factors, the concentration of exposure, and the specific type of metal, either copper or lead. The mutant white-vestigial genotype revealed an IC₅₀ concentration for prolificity inhibition at lower doses of 2.00 mM for copper and 4.00 mM for lead, in contrast to the control genotype (wild-type), which exhibited an inhibition concentration rate >IC₅₀ of 4.00 mM only in the case of copper. Our results concluded that the (i) dose influences the prolificity rate in a directly proportional manner, (ii) comparative analyses between copper and lead revealed that copper displayed toxicity across all genotypes within the concentration range of 0.50 mM to 2.00 mM. In contrast, lead exhibited toxicity within the concentration range of 1.00 mM to 4.00 mM, highlighting a (iii) more acute toxicity characteristic in the case of copper. Thus, the results of this research reflect the importance of using Drosophila melanogaster as a genetic model in the comparative study of the interaction between genetic factors and the toxicity of metals, offering significant insights into monitoring their impact and defining the maximum permissible doses on organisms.

Despite of being an exceptionally biodiversity rich country, the forest coverage of Bangladesh is declining at an alarming rate. Declaration and management of protected areas in this regard is one of the efforts from government side to tackle the loss of biodiversity. The limited numbers of forest-protected areas (FPA), established to conserve the dwindling forest biodiversity of the country with high pressure on them for timber, non-timber forest products, and fuelwood - makes their management challenging. Moreover, most of the FPAs of the country declared only in the recent decades with very limited infrastructure, manpower and policy support for monitoring and governance. Some people-centred approaches for the management of FPAs and alternative livelihood and income generation subsidies although made available through a few project interventions, their number are still inadequate and performance remains less than satisfactory. This chapter provides a critical review of the FPAs of Bangladesh looking at their role in biodiversity conservation, management challenges, and key lessons from previous management interventions with recommendations for the future. It has been revealed that the FPA system of Bangladesh still poorly represents the diverse forest ecosystems with relatively small forest size and lack of corridors for the movement of wildlife. There are ample opportunities to render co-management of FPAs an effective strategy to minimize the conflicts in FPAs management in the country. It is, however, important to ensure the access of local forest-dependent people to different alternative income generating options that may adequately support their livelihoods.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

This work aimed to develop an anionic cellulose nanofiber (CNF) bio-adsorbent from palm date tree waste and to investigate its removal efficiency against cationic methylene blue dye from contaminated water. Palm date pulp was first prepared from palm date leaves through acid hydrolysis using H2SO4, followed by hydrolysis in a basic medium using KOH, in which the process completely removed the components of hemicellulose, lignin, and silica. To obtain anionic CNF, the resulting pulp was further treated with H2SO4, followed by centrifugation. Biogel formation of the CNF suspension was promoted by sonication, where its removal efficiency of methylene blue dye was studied as a function of dye concentration, temperature, contact time, and pH value. Two equilibrium models, the Langmuir and Freundlich models were employed, and the Langmuir model was found to be consistent with the experimental data. The highest removal efficiency was obtained at 60oC and was 5mg/gm. Furthermore, several kinetic models were used to gain insight into the adsorption mechanism. The pseudo-second-order model provided an accurate description of the adsorption process, while the Elovich equation suggested a chemical reaction between methylene blue dye and CNF. The study’s findings were in agreement with the pseudo-second-order model, indicating general chemical reactions. The study indicates that CNF adsorbents derived from renewable natural waste sources such as palm date leaves can be effective in removing cationic contaminants such as methylene blue dye.

To map Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV 2) spreading and evaluate immune responses variations against this virus, it was essential to locally set up efficient serological tests. The SARS-CoV2 immunogenic proteins were very expensive and not affordable mainly for Low and Middle Income Countries (LMICs). For this purpose, the commonly used antigen, Re-ceptor-Binding Domain (RBD) of Spike S1 protein (S1RBD), was produced using the the Baculovirus Expression Vector System (BEVS) . During the current study, the expression of S1RBD was monitored using western blot under different culture conditions. Different parameters were studied: Multiplicity Of Infection (MOI), cell density at infection and harvest time. Hence, optimal conditions for efficient S1RBD production were identified: MOI 3; cell density at infection 2-3x 106 cells/mL and time post-infection (tpi or harvest time) of 72h and 72-96 h successively for expression in shake-flasks and 7L-bioreactor. A high production yield of S1RBD varying between 4mg and 70 mg per liter of crude cell culture supernatant was achieved, respectively, in shake-flasks and in 7L-bioreactor. Moreover, the produced S1RBD showed an excellent antigenicity potential against COVID-19 patient sera evaluated by western blot. Thus, additional serological assays, such as ELISA, were developed using the purified S1RDB (published by other research groups).

The present study aimed at investigating the in vitro and in vivo susceptibility of malaria parasites to crude extracts and fractions from Polyalthia suaveolens, Uvaria angolensis, and Monodora tenuifolia. The ethanolic extracts were prepared by maceration, and were further partitioned using water, dichloromethane, hexane, and methanol. The most promising fraction was subjected to column chromatography and the sub-fractions tested for activity in vitro. The antiplasmodial effect of extracts and fractions was tested against the Chloroquine resistant (PfK1) strain in 96 wells microtiter plate format using SYBR green florescence assay. The promising fraction was further assessed for cytotoxicity and acute toxicity in Swiss albino mice and subsequently against the rodent malaria parasite, P. berghei. Qualitative phytochemical screening was also performed on the promising fraction. The methanol fractions exerted the overall better effect with that of the twigs of P. suaveolens (PStw(Ace)) showing the highest potency with a IC50 value of 3.24 µg/mL followed by the fractions of leaf of M. tenuifolia (MoTel(Ace), IC50= 3.84 µg/ml) and stem bark of P. suaveolens (IC50= 4.90 µg/ml). The phytochemical screening showed the presence of alkaloids, lactones, and phenols in the more active fraction of P. suaveolens (PStw(Ace)). The chromatographic fractionation of this fraction led to 12 sub-fractions with PS8 sub-fraction being the most active (IC50= 4.42 µg/mL). In vivo, oral administration of 2000 mg/kg b.w of fraction PStw(Ace) in mice showed no signs of toxicity. Also, fraction PStw(Ace) at 400 mg/kg b.w exerted the highest suppressive effect against P. berghei strain B throughout the 4 days experiment (% parasitaemia below 5.2%). Overall, the results achieved supported the use of the three plants in the traditional treatment of malaria in Cameroon. More interestingly, the methanolic fraction of the twigs extract from P. suaveolens might be of interest in future development of an antimalarial phytodrug.

Background: Microscopic examination of acid-fast stained sputum smears for detecting mycobacterial acid-fast bacilli (AFB) remains the most economical and readily available method for laboratory diagnosis of tuberculosis (TB). However, this conventional approach has limitations, including low sensitivity and labor-intensive procedures. Methods: An automated microscopy system incorporating artificial intelligence (AI) and machine learning for AFB identification was evaluated. The study was conducted at an Infectious Disease Hospital in Jiangsu Province, China, utilizing an intelligent microscope system (TB-Scan, Wellgen Medical, Kaohsiung). A total of 1,000 sputum smears were included in the analysis, with the system capturing digital microscopic images and employing an image recognition model to automatically identify and classify AFB. Referee technicians provided the gold standard for discrepant results. Results: The automated system demonstrated an overall accuracy of 95.00% (950/1,000), sensitivity of 91.24% (177/194), and specificity of 95.91% (773/806). Notably, the system identified 21 smears as positive that were previously reported as negative, with referee technicians confirming 17 of these as true positive and retracting the test results accordingly. Recalculating the performance, the accuracy increased to 96.70% (967/1,000), sensitivity to 91.94% (194/211), and specificity to 97.97% (773/789), with a false negative rate of 8.06% (17/211) and a false positive rate of 2.03% (16/789). Conclusions: The incorporation of AI and machine learning into an automated microscopy system demonstrated the potential to enhance the sensitivity and efficiency of AFB detection in sputum smears compared to conventional manual microscopy. This approach holds promise for widespread application in TB diagnostics and potentially other fields requiring labor-intensive microscopic examination.

The majority of investigations on microbial communities from various environments are presently built on culture-independent methods. Many studies point to the pivotal, selective role of primers targeting hypervariable regions of 16S rRNA in the metabarcoding of bacteria, including cyanobacterial communities. The selectivity of primers designed to amplify targeted regions of the 16S rRNA gene, which has been highlighted by many authors, limited effective amplification. Moreover, the type and specificity of the studied material can also negatively influence the results of 16S metabarcoding. Most of the studies of cyanobacterial communities have been performed for planktonic microbial communities that are often represented by common, well-studied species. In this study, we present the results of 16S metabarcoding analysis using three primer pairs - two already well-known and a third designed in this study - that amplify divergent regions of the 16S rRNA gene (V3-V4, V4-V6, V6) for benthic, microbial mat-forming cyanobacteria communities. Such communities can be a source of toxigenic cyanobacterial taxa and should be monitored with adequate primers. The comparison of three primer pairs suggested that those designed within the present study describe the structure and composition of highly heterogeneous cyanobacterial mats’ communities better than the others

Annually, more than 1.5 million preventable new hepatitis B (HBV) infections continue to occur, with an estimated global burden of 296 million individuals living with chronic hepatitis B infection. This substantial health challenge results in over 820,000 annual deaths attributed to complications such as liver cirrhosis and hepatocellular carcinoma (HCC). HBV vaccination remains the cornerstone of public health policy to prevent chronic hepatitis B and its related complications. It serves as a crucial element in the global effort to eliminate HBV, as established by the World Health Organization (WHO), with an ambitious 90% vaccination target by 2030. However, reports on global birth dose coverage reveal substantial variability, with an overall coverage rate of only 46%. This comprehensive review thoroughly examines global trends in HBV vaccination coverage, investigating the profound impact of vaccination on HBV prevalence and its consequences across diverse populations, including both high-risk and general demographics. Additionally, the review addresses the formidable challenges and facilitating factors essential for achieving WHO's HBV vaccination coverage objectives and elimination strategies in the coming decade and beyond.

This study investigated the influence of single nucleotide polymorphisms (SNPs) in genes asso-ciated with the interferon pathway (IFNAR2 rs2236757), antiviral response (OAS1 rs10774671, OAS3 rs10735079), and viral entry (ACE2 rs2074192) on COVID-19 severity and their association with non-alcoholic fatty liver disease (MAFLD). We did not observe a significant association between the investigated SNPs and COVID-19 severity. While the IFNAR2 rs2236757 A allele correlated with higher creatinine levels upon admission and the G allele with lower band neu-trophils upon discharge, these findings require further investigation. The distribution of OAS gene polymorphisms (rs10774671, rs10735079 did not differ between MAFLD and non-MAFLD patients. Our study population's distribution of ACE2 rs2074192 genotypes and alleles differed from the European reference population. Overall, our findings suggest that these specific SNPs may not be major contributors to COVID-19 severity in our patient population, highlighting the potential role of other genetic factors and environmental influences.

In contemporary times, the landscape of malware analysis has advanced into an era of sophisticated threat detection. Today's malware sandboxes not only conduct rudimentary analyses but have evolved to incorporate cutting-edge artificial intelligence and machine learning capabilities. These advancements empower them to discern subtle anomalies and recognize emerging threats with a heightened level of accuracy. Moreover, malware sandboxes have adeptly adapted to counteract evasion tactics, creating a more realistic and challenging environment for malicious entities attempting to detect and evade analysis. This paper delves into the maturation of malware sandbox technology, tracing its progression from basic analysis to the intricate realm of advanced threat hunting. At the core of this evolution is the instrumental role played by malware sandboxes in providing a secure and dynamic environment for the in-depth examination of malicious code, contributing significantly to the ongoing battle against evolving cyber threats. In addressing the ongoing challenges of evasive malware detection, the focus lies on advancing detection mechanisms, leveraging machine learning models, and evolving malware sandboxes to create adaptive environments. Future efforts should prioritize the creation of comprehensive datasets, distinguish between legitimate and malicious evasion techniques, enhance detection of unknown tactics, optimize execution environments, and enable adaptability to zero-day malware through efficient learning mechanisms, thereby fortifying cybersecurity defences against emerging threats.

Soil moisture modeling is necessary for many hydrometeorological and agricultural applications. One of the ways in which modeling of soil moisture (SM) can be improved is by assimilating SM observations to update the model states. Remotely sensed SM observations are prone to being riddled with data discontinuities, namely in the horizontal and vertical spatial, and temporal dimensions. A set of synthetic experiments were designed in this study to assess how much impact each of these individual components of spatiotemporal gaps can have on the modeling performance of SM as well as streamflow. Results show that not having root-zone SM estimates from satellite derived observations is most impactful in terms of modeling performance. Having temporal gaps and horizontal spatial gaps in the satellite SM data also impacts modeling performance, but to a lesser degree. Real-data experiments with the remotely sensed Soil Moisture Active Passive (SMAP) product generally brought improvements to the SM modeling performance in the upper soil layers, but not so much in the bottom soil layer. The updating of model SM states with observations also resulted in some improvements in the streamflow modeling performance during the synthetic experiments, but not during the real-data experiments.

Modular steel buildings (MSBs) interlocking inter-module connections (IMCs) have piqued researchers’ interest. However, the existing literature has not yet studied the optimisation of its plate thicknesses. This paper, therefore, focuses on optimising interlocking (IMCs) plate thickness in (MSBs), leveraging previous experimental and numerical simulation methodologies. Various numerical models for four MSBs interlocking (IMCs) with plate thicknesses (4 mm, 6 mm, 10 mm, and 12 mm) were developed under compression loading conditions. The study’s novelty lay in its comprehensive parametric analysis, which evaluated the slip phenomenon in (MSBs) connections and introduced a slip prediction model validated against empirical data. Further innovative machine learning approach was utilised to predict slip values based on applied force through a random forest regression model trained using the 'Treebagger' function. Sensitivity analysis and comparisons with alternative methods were utilised to underscore the reliability and applicability of the findings. The results showed that 11.03 mm was the optimal plate thickness for interlocking (IMCs) in modular steel buildings, with up to 8.08% reduced material costs. Increasing plate thickness boosts its deformation resistance by up to 50.75%. ‘TreeBagger’ random forest for anomaly detection and machine learning improves slip prediction up to 7% at higher force levels.

Organisms are adapted to each other and the environment, not as tradition would have it, because natural selection made them that way, but because there is inbuilt striving towards stability and equilibrium. A General Theory of Behaviour connects imagery, affect and action with the central executive system we call Consciousness. The General Theory is founded on the assumption that the primary motivation of all of Consciousness and intentional behaviour is Psychological Homeostasis. Psychological homeostasis is as important to the organisation of mind and behaviour as Physiological Homeostasis is to the organisation of bodily systems. Consciousness processes quasi-perceptual images independently of the input to the retina and sensorium. Consciousness is the “I-Am” control centre for integration and regulation of (my) thoughts, (my) feelings and (my) actions with (my) conscious mental imagery as foundation stones. Imagery vividness, a combination of clarity and liveliness, is essential to imagining, remembering, thinking, predicting, planning and acting. Assessment of vividness using introspective report is validated by objective means such as fMRI. A significant body of work shows that vividness of visual imagery is determined by the similarity of neural responses in imagery to those occurring in perception of actual objects and performance of activities. I am Conscious, therefore I am.

Learning dental procedures is a complex task involving the development of fine motor skills. The reported use of theories and/ or evidence for designing learning activities to develop the fine motor skills needed for dental practice is limited. The aim of this review is to explore the available body of knowledge related to learning fine motor skills in dentistry. Evidence from studies investigating motor skill learning highlights the negative impact of self-focus and self-regulation on learning outcomes, particularly during the early stages of learning. The development of activities and schedules that enable novices to demonstrate characteristics similar to experts, without the reported long period of ‘deliberate practice’, is clearly of value. Outcomes of learning implicitly are important in dentistry because working under stressful conditions is common, either during undergraduate study or in practice. It is suggested that learning implicitly in the simulation stage can reduce disrupted performance when transitioning to clinical settings. Therefore, further investigation of effective methods for learning dental fine motor skills is indicated, using approaches that result in robust performance, even under stressful conditions.

Water is essential for all living things however its pain has become serious. Many industrial activities cause its pollution by the release of polluting byproduct. Waste water treatment is hence necessary. In this context, the waste water of the textile industry containing Red Acid 52 was treated by the solid waste of the washed natural phosphate byproduct. Natural phosphate was also studied. The solid materials were first characterized by chemical analysis, Fourier Transform Infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The phosphate materials were after that, tested in the adsorption of the Red Acid 52. The experimental data indicated that the phosphate waste rock allowed the removal of Red Acid 52. Its maximum retention capacity attained 18.4 mg.g-1. Calcinations of materials inhibits the removal capacity found reduced by 60 to 70%. The adsorption kinetics of the Red Acid 52 on the material is well described by the pseudo second order model while the adsorption isotherms are identified by the Langmuir model. Hereafter, the thermodynamic study revealed that the adsorption process is spontaneous and exothermic. Keywords: Waste water, Phosphate co-product, Adsorption, Red Acid 52.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

This study delves into the dynamic field of medical education research, emphasizing the integration of research training within medical curricula. It seeks to understand the impact of such integration on the competencies of future medical professionals. The primary aim is to systematically categorize and analyze the current trends and future directions in medical education research. This involves assessing the influence of research training on medical students' skills and the methodologies used in such research. Methods: The research employs an extensive bibliographic literature review across multiple databases. It classifies studies into categories like experiential or case studies, editorials, and original research articles. This classification is based on criteria such as geographical location, research objectives, theoretical frameworks, and methodologies. Results: Findings reveal a diverse landscape in medical education research, with a significant emphasis on research training. The research showcases varying methodologies and approaches used globally, highlighting the thematic focus and geographical distribution of these studies. Conclusion: Medical education research is a globally expansive and evolving field. It underscores the importance of continuous investigation, particularly focusing on integrating research elements at curricular levels and exploring innovative educational strategies. The study also points out potential gaps in research, especially in underrepresented regions, indicating directions for future research efforts.

Background/Purpose: Multimorbidity of malaria, anaemia, and malnutrition (MAMM) is a condition in which an individual cohabits with two or more of these health outcomes and is becoming an emergent public health concern in sub-Saharan African countries. The independent associations of a child’s demographic variables and socioeconomic disparities with a child’s health outcomes have been established in literature. However, the effects of the intersection of these factors on MAMM, while accounting for other covariates have not been studied. Therefore, this study aimed to determine how children’s sex, age and socioeconomic status interact to explain the variations in MAMM among children aged 6-59 months in Nigeria. Methods: Data from the 2018 Nigeria Demographic and Health Survey and the 2018 National Human Development Report (NHDR) were used. The study includes weighted samples of 10,184 children aged 6-59 months in Nigeria. A three-level multilevel mixed effect ordinal logistic regression model such that individual characteristics at level 1 are nested in communities at level 2 and nested in states at level 3 was used. Subsequently, predictive probability charts and average adjusted probability tables were used to interpret the intersectional effects. Five models were created in this scenario. Model 1 is the interaction between the child's sex and wealth status; model 2, child's sex and age; model 3 is between child's age and wealth status; model 4 has the three 2-way interactions of child's sex, age, and household wealth status, and model 5 includes model 4 and the 3-way interactions between a child's sex, age, and wealth quintiles. Results: The prevalence of children with ‘none of the three diseases’ outcomes was 17.3% (1767/10,184), while, 34.4% (3499/10,184) had ‘only one of the diseases’, and 48.3% (4,918/10,184) cohabit with ‘two or more’ of MAMM. However, in the multivariate analyses, model 3 was the best fit compared with other models, so, that the two-way interaction effects of a child's age and wealth status are significant predictors in the model. Children aged 36-47 months living in the poorest households have the probability of 0.11, 0.18, and 0.32 of contracting MAMM above the probability of children of the same age and live in the middle, more prosperous and richest households, respectively, while all other covariates are held constant. Thus, the variation in MAMM over a child's age differs depending on the household wealth quintile. In other words, as the children grow older, variations in MAMM become more evident between the rich and the poor household. Conclusion: Therefore, it is recommended that policies that are geared toward economic redistribution will help bridged the disparities observed in multiple diseases among children aged 6-59 months in Nigeria

Here we present 1. a model for amplicon sequencing 2. a definition of the best assignment of a read to a set of reference sequences 3. strategies and structures for indexing reference sequences and computing the best assign- ments of a set of reads efficiently, based on (ultra)metric spaces and their geometry The models, techniques, and ideas are particularly relevant to scenarios akin to 16S taxonomic profiling, where both the number of reference sequences and the read diversity is considerable.

Predicting the prices of cryptocurrency owing to its volatility, instability, and other factors has been challenging; investors and traders especially in Nigeria have been on a constant look for a more reliable way of knowing market trends and prices and while there has been so many research conducted using deep learning, the results for which has fall short of what investors could called a strong predictor. This research reviewed the results of many works that had been done and proposed two types of recurrent neural network (RNNs) namely Long Short-Term Memory and Gated Recurrent Unit (GRU) for predicting the future prices of two of the most common crypto assets namely Bitcoin (BTC) and Ethereum (ETH), these two were selected based on their popularity, the volume traded and their market capitalization. The experiment was conducted in a GPU Jupyter Notebook environment and the performance of our experiment was evaluated on a test set using root mean square error (RMSE) and based on its values, the LSTM presented a better performance with rsme scores of 654.66, and 80.30 respectively for BTC and ETH as compared to GRU. The paper proceeds further to compare the results of this experiment with other related works and we discovered that its performance is a great improvement.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

Aluminum, a contentious trace element found in the environment, has been demonstrated to have harmful effects on both humans and animals. In contrast, Sempervivum tectorum, an evergreen plant, has been found to offer numerous beneficial effects for both humans and animals. Therefore, this study aims to assess the protective effect of S. tectorum on certain reproductive biomarkers in male rats exposed to aluminum. Thirty-five Wistar rats were randomly divided into five groups: NTC (no-treatment control) received distilled water; NC (negative control) received drinking water containing 1 mg/L aluminum sulfate (AS); E1 received 1 mg/L AS along with an 8% S. tectorum extract; PC (positive control) received only 8% S. tectorum extract; E2 received 1 mg/L AS for three months followed by 8% extract for one month. The study analyzed testosterone, LH, FSH, body weight, and the histological structure of the testis, epididymis, and prostate, as well as the levels of zinc, manganese, copper, and iron in these organs. Significant decreases in body weight, testis, and epididymis size were observed in the aluminum-exposed groups compared to the control, whereas these decreases were not significant in the S. tectorum-treated groups compared to the control. Aluminum exposure led to significant decreases in testosterone and LH levels, with FSH levels showing a non-significant decrease in males, which were mitigated significantly by the administration of the plant extract. Histological analysis revealed alterations in the testis, epididymis, and prostate of the AS-exposed groups, including necrosis of seminiferous tubule epithelium and Leydig cells in the testis, and basal epithelial necrosis in the epididymis and prostate. Aluminum levels increased in all organs studied, while levels of zinc, copper, iron, and manganese decreased, showing a negative and significant correlation with aluminum levels. The aqueous extract of S. tectorum demonstrated a protective effect on certain studied biomarkers in male rats affected by aluminum exposure.

Aim: This study measures and evaluates the socioeconomic burden of people living with keratoconus in Saudi Arabia. Methods: The study employed a cross-sectional design, a Keratoconus Economic Burden Questionnaire, and a convenient sample of 89 keratoconus patients (58.4% male) drawn from multiple regions in Saudi Arabia. It was conducted using online surveys and the data was analysed using appropriate quantitative techniques. Results: The mean age and annual income of participants were 33.24 years and Saudi Riyal (SAR) 33,505.6180 (SD=62,215.29), respectively, with only 37% being employed for wages. Up to 94.4% needed glasses or contact lenses at least once a week and 73.0% received care from optometrists. The condition forced 45.9% of the respondents to change careers or leisure activities, with a further 51.3% having to take time off work. The mean annual out-of-pocket expenses for buying and maintaining glasses or contact lenses as well as traveling and accommodation for keratoconus-related treatment were SAR 8,673.19 (SD=11,307.73), with 48.32 incurring upwards of SAR 12,000 over the period. The treatment costs increased with disease duration, r(89) = .216, p < .05. Regression results show that the existence of comorbid eye disease, changing glasses at least once a year, and wearing either glasses or contact lenses at least once a week individually have statistically significant, negative effects on the total annual keratoconus treatment costs, while disease duration, utilisation of optometrists, and taking time off had a statistically significant increase on the total cost (p<.05). Conclusion: With a prevalence rate of 1 in 375, progressive debilitation, and the lifetime nature of the disease, keratoconus is a critical public health concern in Saudi Arabia. The resulting visual impairment and discomfort as well as both direct and indirect economic burdens have considerable impacts on the patient's quality of life.

Background/Purpose: Over the last two decades, malaria has remained a major worldwide public health concern, especially in the developing countries leading to high morbidity and mortality among children. Nigeria is the world most burdened malaria endemic nation, contributing more than a quarter of global malaria cases. This study determined the prevalence of malaria among children 6-59 months in Nigeria, and the effects of individual and contextual factors. Methods: The study utilized data from 2018 Nigeria Demographic and Health Survey (NDHS) involving a weighted sample size of 10,185 children who were tested for malaria using rapid diagnostic test (RDT). Given the hierarchical structure of the data set, such that children at level-1 are nested in community at level-2, and nested in states and Federal Capital Territory (FCT) at level-3, multilevel mixed effect logistic regression models were used for the analysis. Results: The proportion of children 6-59 months of age in Nigeria that had malaria fever positive as assessed by RDTs was 35.5% (3,418/10185), (CI: 33.9-37.1). Kebbi State had the highest proportion of children 6-59 months who were malaria positive, 77.6%, (CI: 70.2-83.5), followed by Katsina State, 55.5%, (CI: 47.7-63.1). The Federal Capital Territory (FCT), Abuja had the proportion of 29.6%, (CI: 21.6-39.0), malaria positive children of 6-59 months of age. Children between the age of 48 and 59 months were 2.68 times more likely to have malaria fever than children 6-11 months of age (AOR=2.68, 95% CI: 2.03-3.54). Also, children from the rural area (AOR= 2.12, 95% CI: 1.75-2.57), were more likely to suffer from malaria infection compare with children from urban area. Conclusion: The study identified some individual and contextual predictors of malaria among children in Nigeria. These factors are areas that need to be considered for policy designs and implementations toward control and total elimination of malaria-related morbidity and mortality among children in Nigeria.

Tumor to stroma ratio is a highly debated prognostic factor in the management of several solid tumors and there is no universal agreement on its practicality. In our study we proposed to confirm or dismiss the hypothesis that a simple measurement of stroma quantity is an easy-to-use and strong prognostic tool. We have included 74 consecutive patients with colorectal cancer who underwent primary curative abdominal surgery. The tumors have been grouped into stroma-poor (stroma &lt;10%), medium-stroma (between 10 and 50%) and stroma-rich (over 50%). The proportion of tumor stroma ranged from 5% to 70% with a median of 25%. Very few, only 6.8% of patients had stroma-rich tumors, 4% stroma-poor tumors and 89.2%tumors with a medium quantity of stroma. The proportion of stroma, at any cut-off, had no statistically significant influence on the disease specific survival. This can be explained by the low proportion of stroma-rich tumors in our patient group and the inverse correlation of stroma proportion with tumor grade. The real-life proportion of stroma-rich tumors and the complex nature of the stroma-tumor interaction has to be further elucidated.

The prevalence of diabetes mellitus (DM), considered one of the most common metabolic disorders, has dramatically increased and resulted in higher rate of morbidity and mortality around the world, in the past decade. It is well known that insulin resistance in target tissues and a deficiency in insulin secretion from pancreatic β-cells are the main characteristic of type 2 diabetes. The aim of this study was the bio-evaluation of compounds isolated from three selected plant species; namely, Salvia africana-lutea, Leonotis ocymifolia and Plectranthus madagascariensis, for their glucose uptake ability. Methanolic extracts were produced from the arterial part of each plant. Compounds were identified using different spectroscopic techniques. The glucose uptake ability of each compound was then evaluated in mammalian cells using 2-deoxyglucose-6-phosphate. The cytotoxicity of each compound was established via the MTT assay. Chromatographic purification of the three plant species yielded fifteen pure terpenoids. Compounds 1 (p = 0.0031), 8 (p = 0.0053), and 6 (p = 0.0086), showed a marked increase in glucose uptake, with p values of p=0.0031, p=0.0053 and p=0.0086, respectively. Additionally, 1, 4 and 6 exhibited cytotoxicity toward mammalian tissue with a decrease in cell viability of ~70%, ~68% and ~67%, respectively. The results suggested that several compounds demonstrated a marked increase in glucose uptake while two of the compounds exhibited signs of cytotoxicity. It may, therefore, be suggested that these compounds be considered as potential candidates for novel plant-derived alternative therapies in the treatment of type 2 diabetes.

The aim of this work was to classify the business incubators in Spain according to the four phases of startups incubation. Taking into account that the graduation rate implies greater survival and business success of the incubated companies, they have been identified at each stage of the incubation (spread of entrepreneurship, pre-incubation, advanced incubation, and graduation). The activities that present higher impacts on the success of the incubated companies and the activities carried out by the incubator that have a greater relevance on the graduation of the companies have concretely been considered. Principal component (PC) cluster analysis have been applied. All the incubation variables were used simultaneously, reducing their number, and grouping them into factors, finally the cases were grouped according to these latent variables. Principal components analysis reduced dimensionality to 8 factors with a 74 % of explained variance. Factor 1 was positively related to pre-incubation variables, factor 2 was linked to training and collaboration variables within the entrepreneurship diffusion phase. Factor 3 called activity monitoring and control and was related to phase 3 or basic incubation variables. Clusters analysis facilitates the grouping of incubators into three clusters: Group 1 (16 % of the total), incubators with strong deficits in incubation phases 1, 2 and 3. They are small Business Incubators, often located in rural areas or cities and low graduation rate. Group 2 (30 %), business incubators with very high graduation rate, and strongly positive values in factor 1 and 2. Factor 3 although positive is susceptible to improvement. They are the largest incubators and usually located in industrial and technological parks. Group 3 (54 %) is the majority, with values close to cluster 2 and 3.

Patients with locally advanced head and neck squamous cell carcinoma (HNSCC) frequently require primary radiochemotherapy (RCT). Despite intensity-modulation, desired radiation-induced effects observed in HNSCC, may also be observed as side-effects in healthy tissue e.g. the sternocleidomastoideus muscle (SCM). These side-effects (e.g. tissue fibrosis) depend on the interval between completion of RCT and restaging-CT. For salvage surgery, the optimal time window for surgery is currently postulated between 6 and 12 weeks after completion of RCT. Thus, no extensive tissue fibrosis is to be expected. This interval is based on studies exploring surgical complications. Studies directly exploring radiation-induced changes of the SCM in HNSCC-patients are sparse. The present study quantifies tissue alterations in SCM and paravertebral musculature (PVM) after RCT applying radiomics to determine the optimal time window for salvage surgery. Three radiomic key parameters 1) volume, 2) mean positivity of pixels (MPP) and 3) uniformity were extracted with mint lesionTM in the staging-CTs and restaging-CTs of 98 HNSCC-patients. Of these, 25 were female, the mean age was 62 (±9.6) years and 80.9% were UICC Stage IV. The mean restaging-interval was 55 (±28; range29-229) days. Only the mean volume significantly decreased after RCT from 9.0 to 8.4 and 96.5 to 91.9 ml for SCM and PVM, respectively (both p=0.007, both Cohen’s d=0.28). In addition, the mean body mass index (BMI) decreases from 23.9 (±4.2) to 21.0 (±3.6) kg/m² (p<0.001); Cohen's d = 0.9). The mean BMI-decrease significantly correlated with the volume decrease for SCM (r=0.27; p=0.007) and PVM (r=0.41; p<0.001). If t-test p-values were adjusted for the BMI-decrease, no significant change in volumes for SCM and PVM was observed (both p>0.05). The present data supports the postulated optimal interval for salvage surgery of 6 to 12 weeks. Irrespective of the remaining risk-benefit ratio of salvage surgery, the risk of additional surgical complications due to fibrosis is not supported by the present observations.

Keywords: Pain; Nociception; Disorders of Consciousness; Consciousness

: Plant-derived terpenes have aroused considerable interest as chemotherapeutic agents for a variety of diseases. This study aimed at the isolation and purification of the scarce terpenes psiadin, plectranthone and saudinolide from their respective plants, followed by the determination of antiproliferative activity, against hepatic cancer cell lines (HepG2, Hep3B), and the potential molecular mechanisms. Time- and dose-dependent cytotoxicity, evaluated using MTT and colony-forming assays, were exhibited by psiadin and plectranthone against the cancer cells. Flow cytometry showed that these two terpenes blocked cell cycle progression and induced mitochondrial-mediated apoptosis, particularly through increased cytochrome c and disruption of mitochondrial membrane potential. Additionally, they initiated the generation of reactive oxygen species as well as inhibiting NF-B. Psiadin lowered several essential cyclins and cyclin-dependent kinases and reduced RB activation. It was concluded that psiadin, in particular, has a significant therapeutic potential with the biggest advantage of differentiating between cancer and normal cells which is acutely lacking in current cytotoxic drugs. Its precise mode of action needs further investigation but appears predominantly to cause cell cycle arrest by interfering with cyclin production. It will be important to determine, in future studies, whether these terpenes will similarly inhibit other cancer cell lines and retain its activity against tumors in vivo.

Shiga toxins (Stxs), and more specifically the Stx2a subtype, are the major virulence factors involved in enterohemorrhagic Escherichia coli (EHEC)-associated hemolytic uremic syndrome (eHUS); a life-threatening disease causing acute kidney injury, especially in children. Cleavage of Stxs A subunit, when followed by reduction, boosts the enzymatic activity causing damage to targeted cells. This cleavage was assumed to be mostly mediated by furin during Stx intracellular trafficking. Cleavage of A subunit, without reduction, changes the binding properties of Stxs for blood components during HUS pathogenesis. To investigate whether the cleavage could occur in the intestine, even prior entering target cells, Stx2a structure was characterized after its exposure to specific host factors present in human stool. The structure of Stx2a A subunit was determined by immunoblotting after electrophoretic separation under reducing conditions. Trypsin and chymotrypsin-like elastase 3B (CELA3B), two serine proteases, were identified as potential candidates that may trigger the extracellular cleavage of Stx2a A subunit directly after its secretion by EHEC in the gut. Whether this observation indeed translates to natural infections and plays a role in eHUS pathogenesis has yet to be determined as well as whether host's protease profile could affect disease development by changing the toxin’s biological features.

HLA class-I (HLA-I) polyreactive monoclonal antibodies (mAbs) reacting to all HLA-I alleles were developed by immunizing HLA-E monomeric heavy chain (HC) (Open Conformers, OCs). Two of the mAbs (TFL-006 and TFL-007) bound to the HC’s coated on a solid matrix. The binding was inhibited by a peptide 117AYDGKDY123, present in all alleles of the six HLA-I isoforms but masked by 2-microglobulin -m) in intact HLA-I trimers (Closed Conformers, CCs). Identical HLA-I polyreactivity is observed in IVIg administered to lower anti-HLA antibodies (Abs) in HLA-sensitized patients, but the mechanism is unknown. We hypothesized that the mAbs that mimic IVIg HLA-I polyreactivity might mimic the immunomodulatory functions of IVIg. We tested the relative binding affinity of the mAbs and IVIg for both OCs- and CCs and compared their effects on (a) the phytohemagglutinin (PHA)-activation T-cells, (b) the production of anti-HLA-II antibody (Ab) by B-memory cells, and anti-HLA-I Ab by immortalized B-cells, and (c) the upregulation of CD4+, CD25+, and Fox P3+ T-regs. The mAbs bound only to OCs, whereas IVIg is bound to both CCs and OCs. The mAbs suppressed blastogenesis and proliferation of PHA-activated T-cells, anti-HLA Ab production by B-cells and expanded the T-regs, better than IVIg. We conclude that a humanized version of the TFL-mAbs could be an ideal therapeutic IVIg-mimetic.

Orthohepadnavirus causes chronic hepatitis in a broad range of mammals, including primates, cats, woodchucks, and bats. Hepatitis B virus (HBV) X protein inhibits type-I interferon (IFN) signaling, promoting HBV escape from the innate immune system to establish persistent infection. However, whether X proteins of Orthohepadnavirus viruses in the other species have similar inhibitory activity remains unknown. Here, we investigated the anti-IFN activity of 17 Orthohepadnavirus X proteins derived from various hosts. We observed conserved activity of Orthohepadnavirus X proteins in inhibiting TIR-domain-containing adaptor protein inducing IFN-β (TRIF)-mediated IFN-β signaling pathway through TRIF degradation. X proteins from domestic cat hepadnavirus (DCH), a novel member of Orthohepadnavirus, inhibited mitochondrial antiviral signaling protein (MAVS)-mediated IFNβ signaling pathway comparable with HBV X. These results indicate that inhibition of IFN signaling is conserved in Orthohepadnavirus X proteins.

Spodoptera frugiperda is an invasive pest that has spread in various parts of the world. These pests have the ability to spread and adapt highly to new habitats. Until now, it is not known with certainty the distribution of these invasive pests in Eastern Indonesia, especially Bali and Nusa Tenggara. This study aims to map the spatial distribution and genetic distribution of S. frugiperda which damages maize in the areas of Bali and Nusa Tenggara. This research was conducted using a survey method from May to September 2022 covering the islands of Bali, Lombok, Sumbawa, Sumba, Flores, and Timor. The results showed that S. frugiperda had spread evenly in Bali and Nusa Tenggara. The results of PCR amplification in the COI gene from 9 sample isolates from all research locations showed the similarity of DNA bands leading to the Spodoptera frugiperda species with a banding pattern length of 683 – 697. These results indicated that the distribution of genetic variants of corn caterpillars in Bali, NTB, and NTT was confirmed as S. frugiperda species. However, the isolated gene S. frugiferda, which was shown by the alignment results of the sequences from Lombok, was confirmed as a different strain from strains from Bali, Sumba, Sumbawa, Flores, and Timor. This incident can be seen from the difference in the protein base composition of S. frugiperda from Bali, Sumba, Sumbawa, Timor, and Flores. The results of phylogenetic analysis in this study confirmed 3 clusters of the genetic closeness of S. frugiperda. Cluster-1 comes from the results of the search for specimens of JB FAW and KB FAW from Bali, SB FAW and SB FAW Sorghum from Sumba, SW FAW from Sumbawa, KP FAW from Timor, and FL FAW from Flores. Cluster-2 is an isolate outside of our species. Cluster-3 comes from the search for LT and LS FAW specimens from Lombok. The genetic distance between cluster-1 and cluster-3 is quite far, which is 0.20 mu.

With the increase of the Artificial Neural Network (ANN), machine learning has taken a forceful twist in recent times. One of the most spectacular kinds of ANN design is the Convolutional Neural Network (CNN). The Convolutional Neural Network (CNN) is a technology that mixes artificial neural networks and up to date deep learning strategies. In deep learning, Convolutional Neural Network is at the center of spectacular advances. This artificial neural network has been applied to several image recognition tasks for decades and attracted the eye of the researchers of the many countries in recent years as the CNN has shown promising performances in several computer vision and machine learning tasks. This paper describes the underlying architecture and various applications of Convolutional Neural Network.

Purpose: To compare the efficacy and safety of graft-free short tunnel small flap (STSF) technique with that of scleral patch graft (SPG) in Ahmed glaucoma valve (AGV) implantation. Design: Randomized clinical trial. Participants: Eighty-eyes of eighty patients with medically uncontrolled glaucoma including 41 in STSF and 39 eyes in SPG. Methods: Patients were enrolled and assigned randomly to STSF or SPG. Main Outcome Measures: tube exposure, Intraocular pressure (IOP), number of glaucoma medications, best corrected visual acuity (BCVA), surgical complications, and success rate ( defined as intraocular pressure (IOP) >5 mmHg, ≤21 mmHg, and IOP reduction ≥20% from baseline at two consecutive visits after three months, no reoperation for glaucoma). Results: only one case in SPG developed tube exposure at 1-year follow-up. The cumulative probability of success during the first year of follow-up was 70% in the STSF and 65% in SPG (P = 0.36). IOP decreased significantly from 29.6 ± 8.6 mmHg at baseline to 16.4 ± 3.6 mmHg at the final follow-up in STSF (p = 0.001). The corresponding numbers for SPG were 30.9 ± 11.2 and 15.8 ± 4.7, respectively (p = 0.001). The final IOP was comparable between both groups (p = 0.65). Mean ± standard deviation of the number of glaucoma medications was 1.8 ± 0.9 in STSF and 1.6 ± 0.9 in SPG at final follow-up (P = 0.32). Postoperative complications developed in 8 patients (19%) in STSF and 9 patients (23%) in SPG (P = 0.81). Conclusions: STSF and SPG techniques had comparable complication rate at one-year follow-up. Both techniques were comparable in terms of success rate, postoperative IOP, and glaucoma medications.

Breast cancer is the most common cancer in women globally, often necessitating mastectomy and subsequent breast reconstruction. Silicone mammary implants (SMIs) play a pivotal role in breast reconstruction, yet their interaction with the host immune system and microbiome remains poorly understood. This study investigates the impact of SMI surface topography on host antimicrobial responses, wound proteome dynamics, and microbial colonization. Biological samples were col-lected from ten human patients undergoing breast reconstruction with SMIs. Mass spectrometry profiles were analyzed for acute and chronic wound proteomes, revealing a nuanced interplay between topography and antimicrobial respondseproteins. 16S rRNA sequencing assessed mi-crobiome dynamics, unveiling topography-specific variations in microbial composition. Surface topography alterations influenced wound proteome composition. Microbiome analysis revealed heightened diversity around rougher SMIs, emphasizing topography-dependent microbial inva-sion. In vitro experiments confirmed staphylococcal adhesion, growth, and biofilm formation on SMI surfaces, with increased texture correlating positively with bacterial colonization. This comprehensive investigation highlights the intricate interplay between SMI topography, wound proteome dynamics, and microbial transmission. The findings contribute to understanding host-microbe interactions on SMI surfaces, essential for optimizing clinical applications and minimizing complications in breast reconstruction.

COVID-19 has substantially influenced healthcare systems, requiring early prognosis for innovative therapies and optimal results, especially in individuals with comorbidities. Healthcare practitioners have used AI systems for investigating, anticipating, and predicting diseases, through means including medication development, clinical trial analysis, and pandemic forecasting. This study proposes the use of AI to predict disease severity in terms of hospital mortality among COVID-19 patients. Methodology: A cross-sectional study was conducted the approval from the Research Ethics Committee of King Abdulaziz University (KAU), Saudi Arabia. The study used sequential sampling approaches to include 50 Real-Time Polymerase Chain Reaction (RT-PCR) positive COVID-19 patients from KAU's coronavirus isolation wards. A pre-designed form was used to collect each patient's demographic information, including age and gender, signs and symptoms, illness severity (mild, moderate, severe), and laboratory findings. Furthermore, the length of the hospital stay and the result, whether the patient recovered or died, were reported. Results: The study involved 50 patients with varying degrees of disease severity, most of whom suffered from fever, fatigue, cough, sore throat, and diarrhoea. Laboratory analysis of COVID-19 patients showed increased white blood cell and platelet counts, with C-reactive protein levels above normal. Elevated LDH levels indicated possible tissue damage, while ferritin levels were elevated. Other enzymes were in the normal range, but bilirubin levels were slightly elevated. Overall, the patient's lab results indicated inflammation and possible blood clot formation. The study evaluated the predictive accuracy for outcomes and mortality of COVID-19 patients based on factors such as CRP, LDH, Ferritin, ALP, Bilirubin, D-dimers, and hospital stay (p-value ≤0.05). The predictive accuracy mortality of patients with COVID-19 using AI showed Hospital stay, D-Dimers ALP, Bilirubin, LDH, CRP, and Ferritin significantly affected hospital mortality. (p ≤ 0.0001). Conclusion: Artificial Intelligence is crucial for identifying early coronavirus infections and monitoring patient conditions. It improves treatment consistency and decision-making via the development of algorithms. AI can track the crisis at various scales, facilitate research, and aid in developing treatment regimens, prevention strategies, and drugs and vaccines. It also aids in monitoring health and facilitating research on the virus.

Establishment of protected areas (PAs) is one of the key global conservation strategies that currently cover approximately 15% of the earth’s land surface. Globally, PA networks are designed to curb the growing anthropogenic pressures in areas with high biological diversity. Despite the importance of PAs in conserving the vanishing biodiversity and unique habitats, many of them are in critical condition due to poor governance thus functioning below the expected level. Moreover, in many developing countries, the PA coverage is below the global standard. Recognizing their contemporary role in conservation, governments have recently agreed to expand the global PA coverage to 17% by the year 2020 (Aichi target 11). This book with eight chapters from different regions of the world provides an overview of the PAs governance, institutional mechanisms, conservation benefits, limitations and challenges associated with their respective policy discourse, integrated management, and functional attributes. Protected areas expect to to play an important role in the long rn in conservation and protection of biodiversity and ecosystems particularly in countries where population pressure and habitat loss are high. Regular intervention, political commitment, and effective governance are essential for the sustainability of PAs across the world. Here, we also attempted to shed some light on future development clues for the sustainable management and monitoring of PAs worldwide.

Stress urinary incontinence (SUI) influences the quality of life of women. The research applied ICIQ LUTS qol (The International Consultation Incontinence Questionnaire Lower Urinary Tract Symptoms quality of life) as a tool to measure the quality of life (QOL) of patients with stage 1 SUI in many areas. 140 perimenopausal women who participated in a urodynamic test at Department of Gynecology, Endocrinology and Gynecologic Oncology, Pomeranian Medical University, Police, Poland in the years 2013-2015 were enrolled in the study. Patients were divided into two groups: A and B. Two questionnaires were applied: the author’s original questionnaire and the standardized ICIQ LUTS qol. Gymnastic plans were recommended 4 times per week for the period of 3 months. The plan for group A included the exercises of pelvic floor muscles (PFM) with the simultaneous tension of the transverse abdominal muscle (TrA) and for group B included the exercises of PMF without TrA. The evaluation of the quality of life of patients with stage 1 SUI with the use of ICIQ LUTS qol among patients from groups A and B after therapy showed a significant improvement in most areas. More impact is observed in the physiotherapy of both PFM with TrA.

Various wood fibres, including pine and flax, are used in wood–plastic composites (WPCs). This paper studies the effect of the lignin content on the morphological and thermal degradation and damage due to the ultraviolet (UV) aging of polypropylene/flax (PP-flax) and polypropylene/pine (PP-pine) fibres composites. Flax and pine fibres exhibited distinct densities of 1.51 and 1.47 g/cm³, respectively, potentially influenced by growth factors and varying compositions of light substances, such as hemicellulose, lignin, and impurities. The thermal decomposition mass loss increased proportionally with the percentage of lignin in the fibre. From 238°C to 390°C, the pine fibre exhibited a 72% mass loss compared to flax fibre, which showed a 54% mass loss, owing to the higher lignin content in pine fibres. Based on differential scanning calorimetry (DSC), the fibre composition affected the material melting temperature. Moreover, DSC curves revealed a higher degree of crystallinity in the case of the PP-flax biocomposite (12%) compared to pure polypropylene (9%) and PP-pine (6%). This result can be attributed to the high content of crystalline components in flax fibres, such as cellulose. Acoustic emissions analysis confirmed that the high lignin content delays degradation and mitigates the appearance of microcracks on the surface of the PP-pine biocomposite. Overall, the study provides valuable data for understanding the UV degradation phenomenon in biocomposites and highlights the influence of fibre composition on material performance.

The Solvency II regulatory framework specifies procedures and parameters for determining solvency capital requirements (SCRs) for insurance companies. The proposed standard SCR calculations involve two steps. The Value–at–Risk (VaR) of each risk driver is measured and, in a second step, all components are aggregated to the company’s overall SCR, using the Standard Formula. This formula has two inputs: the VaRs of the individual risk drivers and their correlations. The appropriate calibration of these input parameters has been the purpose of various Quantitative Impact Studies that have been conducted during recent years. This paper demonstrates that the parameter calibration for the equity–risk module—overall, with about 25%, the most significant risk component—is seriously flawed, giving rise to spurious and highly erratic parameter values. As a consequence, an implementation of the Standard Formula with the currently proposed calibration settings for equity–risk is likely to produce inaccurate, biased and, over time, highly erratic capital requirements.

Introduction: Carcinoid heart disease is a rare cause of right-sided valvular dysfunction, an important complication in patients with carcinoid syndrome. Objectives: We aim to present our own experience regarding early myocardial dysfunction in patients with carcinoid syndrome. Methods: 64 patients (35-90 year old, 62,5% female, 37,5% male patients) with carcinoid syndrome were evaluated be-tween October 2017 and June 2021. All patients underwent two-dimensional echocardiography with additional tissue Doppler and speckle-tracking techniques. For all patients there were measured urinary level of 5- hydroxyindolacetic acid, serotonin and NT-proBNP values. Results: The following echocardiographic features: global longitudinal strain of both ventricles, mean systolic velocity of the left ventricle, systolic velocity of the free wall of right ventricle, correlated with high values of specific biomarkers: serotonin, and urinary 5-hydroxyindolacetic acid, and also with the presence of hepatic metastases and poorly differentiated tumors. Discussion: In this study we identified several patients with early myocardial dysfunction due to carcinoid syndrome, representing a predictive model of poor prognosis, requiring further investigations. Conclusion: Echocardiographic assessment based on the measurement of systolic velocities, as well as the global longitudinal strain of both ventricles, together with specific biomarkers may contribute to better recognition of carcinoid heart disease in clinical practice, but this needs validation through further studies enrolling larger number of patients.

This study delves into the intricate interplay of economic growth components, specifically focusing on Consumption and investment in Saudi Arabia from 2000 to 2022. Employing vector error correction models and cointegration techniques, we analyze the short- and long-term dynamics within the relationship of Consumption, investment, and economic growth. Granger causality analysis is also used to discern these pivotal variables' causal connections. Our empirical analysis reveals a persistent long-term cointegration relationship among the variables, underscoring the enduring nature of their interdependency. Furthermore, our findings highlight Consumption and investment's statistically significant positive impact on economic growth. Notably, the short-term analysis unveils a stable model characterized by an annual adjustment to equilibrium of 100%.Moreover, the Granger causality study demonstrates unidirectional causal linkages between Consumption, investment, and economic growth. These findings hold substantial implications for policy formulation in Saudi Arabia. Policymakers must grasp the ramifications of burgeoning prosperity and evolving private consumption patterns on future environmental outcomes. Achieving sustainable long-term results necessitates equal emphasis on bolstering private Consumption and fostering other facets of economic growth.

The aim of our study was a comprehensive comparative assessment of the effect of consumption of 1 and 2% cholesterol as part of a standard diet with and without regular moderate physical activity on the main biomarkers of lipid and cholesterol metabolism, as well as the intestinal microbiota of male Wistar rats. The animals were randomly divided into 5 groups according to body weight and Open Field test results: Control (n=10), 1% Chol (n=10), 2% Chol (n=10), 1% Chol + RUN (n=10) and 2% Chol + RUN. The cholesterol was additionally added in the amount of 1g or 2g/100g, respectively, to the diet of animals. The rats of experimental groups 1% Chol + RUN and 2% Chol + RUN were subjected to regular (2 days a week) physical activity on a Treadmill. In rats of four experimental groups, when compared to the Control, a response of 39 indicators was revealed. The largest number of changes in biomarkers - 29 (statistically significant, p

Lyme disease, the leading vector-borne ailment in the U.S., annually affects an estimated 476,000 individuals, predominantly in the Northeast and Upper Midwest. Despite its increasing incidence, the evaluation of risk within U.S. cities, including natural public lands, remains inadequate. This study focuses on blacklegged tick occurrences and Borrelia burgdorferi infection prevalence in 24 Staten Island parks, aiming to assess Lyme disease exposure risk. Monthly acarological risk index (ARI) calculations from 2019 to 2022 revealed elevated values (0.16-0.53) in specific parks, notably Wolfe’s Pond Park, High Rock Park, Clay Pit Pond Park, Clove Lake Park, and Fair View Park. June (0.36) and November (0.21) consistently exhibited heightened ARIs, aligning with peak tick collection months. Despite stable yearly infection rates at 28.97%, tick densities varied significantly between parks and years. Identifying a high transmission risk in specific parks in Staten Island, a highly urbanized part of New York City, emphasizes the continuous necessity for Lyme disease risk management, even within the greenspaces of large cities.

We present an open-source Star Tracker (ST) for Attitude Determination. Our implementation makes use of open source software of common usage in astronomy running on a Raspberry Pi 2 platform. The developed platform is open and available for parties interested in further development. Evaluation of the system showed that the ST is suitable for Cubesats of 2U or larger. The ST platform is capable of solving the Lost-In-Space (LIS) problem. Currently, the average accuracy reached of the algorithm is close to 5 seconds of arc with an average processing time of 75 seconds. However, a average accuracy of about 3 minutes of arc can be reached with 35 seconds in average processing time. We also describe the evaluation procedure, the found conclusions of this procedure, in particular the section of the algorithm where most of the processing time is spent and other possible source of errors not included in this study.

Pre-diabetes is a serious health condition where blood sugar levels are higher than normal, but not high enough yet to be diagnosed as type 2 diabetes. Pre-diabetes puts one at an increased risk of developing type 2 diabetes and heart disease Methodology: A cross-sectional study was carried out on 384 patients aged 20-70 years old, attending the dental clinics to assess the risk for diabetes, using the FINDRISC questionnaire, HbA1c blood test and a periodontal examination. Results: The mean age of participants was 38.90±10.74. 32.3% were categorized as no risk, 46.6% low risk, while 19% and 2.1% moderate and high risk of developing diabetes respectively. Tests for serum HbA1c Level showed 46.1 % had normal HbA1c followed by 18.0% and 3.6 % were pre-diabetic and diabetic respectively. 19.3% of participants had periodontal pockets measuring more than 4mm and 15.9% measuring more than 6mm. Conclusion: The study has proven to be useful in identifying patients at high-risk of developing diabetes. Controlling and managing periodontal disease could be a new aspect to include in the standards for diabetes care. Dental settings could be a successful platform to carry out the screening and risk stratification of pre-diabetic patients.