The extraction method for simultaneously analyzing fatty acids (Myristic acid, cis-Palmitvaccenic acid, Palmitic acid, Palmitic-9,9-d2 acid, Oleic acid, Stearic acid and Stearic-2,2-d2 acid) related to biodiesel fuel in large algae was developed. The introduction of trimethylaminoethyl (TMAE) derivatives into the hydroxyl group (-OH) functional group of the analyte was able to improve ionization and obtain high sensitivity. Liquid Chromatography (LC) was used to investigate the optimal mobile phase composition and flow rate for the separation of five derived fatty acids. In this study, a solid phase extraction (SPE) column was introduced for efficient extraction of fatty acids, and the optimal conditions for SPE were set by comparing the recovery rate according to the solvent for each step (loading, washing, and elution) of SPE from macroalgae.

Sea fog event over the Eastern Yellow Sea on 15–16 April 2012 was reproduced in the Weather Research and Forecasting (WRF) simulation with high-resolution to investigate the roles of phys-ical processes and synoptic-scale flows on advection fog with sea surface warming. Initially, longwave radiative cooling (LRC) with negative sensible heat flux (SHF) due to the turbulence af-ter sunset triggered a formation of cloud at the surface under the moist advection with a southerly wind. This is a conventional type of advection fog. At night, continuous cooling due to longwave radiation and SHF near the surface modulated the change of the SHF from negative to positive, resulting in a drastic increase in the latent heat flux (LHF) that provided sufficient moisture at lower atmosphere (self-moistening). This is a favorable condition for advection fog with sea sur-face heating (ssH), and this transition represents advection fog with ssH. Enhanced turbulent mixing driven by a buoyancy force increased the depth of the sea fog with a gradual rise in the marine atmospheric boundary layer (MABL) height, even at nighttime. In addition, cold advec-tion with a prevailing northerly wind at the top of the MABL led to a drastic increase in turbulent mixing and the MABL height, which resulted in rapid growth of the height of sea fog due to ver-tical diffusion. After sunrise, shortwave radiative warming in the fog layers offsetting the LRC near the surface weakened thermal instability, which contributed to the reduction in the MABL height, even during the daytime. In addition, dry advection of northerly wind induced dissipa-tion of the fog via evaporation. An additional sensitivity test of sea surface salinity showed weaker and shallower sea fog than the control due to the decrease in both the LHF and local self-moistening.

Air pollutants such as volatile organic compounds (VOCs), nitrogen oxides (NOx), sulfur dioxide (SO2), as well as water pollutants including heavy metal, are harmful to human and environment. Effective control and reduction of their pollution is therefore an important topic for today’s scientists. Fly ash (FA) is a type of industrial waste that can cause multiple environmental problems if discharged into the air. On the other hand, because of its high porosity, large specific surface area, and other unique characteristics, the FA can also be used as a low-cost and high efficient adsorbent with some simple modifications. This paper reviews the effects of FA on treatment of the above air and water pollution based on our research experience over many years, including to the current status of global FA utilization, physicochemical properties, principle of adsorption, and the application direction of FA in the future. It focuses on the use of nanocomposite technology to fabricate functional FA fibrous membranes to adsorb VOCs from air, and treat heavy metal wastewater. This present review first describes the fabrication technology of FA nanocomposites and their mechanism of adsorption VOCs from air. Utilization of nanofiber technology to fabricate multi-functional FA emerging composite materials to mitigate air and water pollution has great potential in the future, especially use of pollutant material to control other pollutants.

Substrate binding proteins (SBP) bind to specific ligands in the periplasmic region and bind to membrane proteins to participate in transport or signal transduction. Typical SBPs consist of two α/β domains and recognize the substrate by hinge motion between two domains. Conversely, short length Rhodothermus marinus SBP (named as RmSBP) exists around the methyl-accepting chemotaxis protein. We previously determined the crystal structure of RmSBP consisting of a single α/β domain, but the substrate recognition mechanism is still unclear. To better understand the short length RmSBP, we performed comparative structure analysis, computational substrate docking, and X-ray crystallographic study. RmSBP shares a high level of similarity in α/β domain with other SBP proteins, but it has a distinct topology in the C-term region. The substrate binding model suggested that conformational change in the peripheral region of RmSBP was required to recognize the substrate. We determined the crystal structures of RmSBP at pH 5.5, 6.0, and 7.5. RmSBP showed structural flexibility of the β1-α2 loop, β5-β6 loop, and extended C-term domain based on the electron density map and temperature B-factor analysis. These results provide information that will further the understanding of the function of the short length SBP.

Background and objectives: Traditional intravenous, patient-controlled analgesia (PCA) uses a fixed-rate continuous background infusion mode. However, some patients suffer from inadequate analgesia or opioid-related adverse effects due to the biphasic pattern of postoperative pain. Therefore, we investigated the postoperative analgesic efficacy of PCA using an optimizing background infusion mode (OBIM), where the background injection rate varies depending on the patient's bolus demand. Materials and Methods: We prospectively enrolled 204 patients who underwent laparoscopic cholecystectomy in a randomized, controlled, double-blind study. Patients were allocated into either the optimizing (group OBIM) or the traditional background infusion group (group TBIM). The numeric rating scale (NRS) score for pain was evaluated at admission to and discharge from the recovery room, as well as at the 6th, 24th, and 48th postoperative hours. Data of bolus demand count, total infused volume, and background infusion rate was downloaded from the PCA device at 30-min intervals until the 48th postoperative hour. Results: The NRS score was not significantly different between groups throughout the postoperative period (P = 0.621), decreasing with time in both groups (P < 0.001). The bolus demand count was not significantly different between groups throughout (P = 0.756). The mean cumulative infused PCA volume was lower in group OBIM [84.0 (95% confidence interval: 78.9−89.1) mL) than in group TBIM [102 (97.8−106.0) mL] (P < 0.001). The background infusion rate was significantly different between groups throughout (P < 0.001); it was higher in group OBIM than in group TBIM before the 12th postoperative hour, and lower from the 18th to the 48th postoperative hours. Conclusions: The OBIM combined with bolus dosing is useful in that it reduces the cumulative PCA volume compared to the TBIM combined with bolus dosing, while yielding comparable postoperative analgesia and bolus demand in patients undergoing laparoscopic cholecystectomy.

The present study was conducted to investigate the effects of rhizome extract of Dioscorea batatas (Dioscoreae Rhizoma, Chinese Yam) and its bioactive compound, allantoin, on myoblast differentiation and mitochondrial biogenesis in skeletal muscle cells. Yams were extracted in water and the extract was analyzed by HPLC. The expression of C2C12 myotubes differentiation and mitochondrial biogenesis regulators were determined by reverse transcriptase (RT)-PCR or Western blot. The glucose levels and total ATP contents were determined by glucose consumption, glucose uptake and ATP assays, respectively. Treatment with yam extract (1 mg/mL) and allantoin (0.2 and 0.5 mM) significantly increased of MyHC expression compared with non-treated myotubes. Yam extract and allantoin significantly increased the expression of mitochondrial biogenesis regulating proteins, PGC1?, Sirt-1, NRF-1, and TFAM, as well as the phosphorylation of AMPK and ACC in C2C12 myotubes. Furthermore, yam extract and allantoin significantly increased the glucose uptake levels and the ATP contents. Finally, HPLC analysis revealed that the yam extract contained 1.53% of allantoin. Yam extract and allantoin, stimulated myoblast differentiation into myotubes and increased energy production through upregulation of mitochondrial biogenesis regulators. These findings indicate that yam extract and allantoin can help to prevent the skeletal muscle dysfunction through stimulation of energy metabolism.

Objective: The pleiotropic effect of hydroxy-3-methylglutaryl coenzyme A (HMG-CoA) reductase inhibitors (statins) is responsible for potent defense against inflammatory response. This study evaluated the inhibitory effects of HMG-CoA reductase inhibitors on monosodium urate (MSU)-induced inflammatory response through the regulation of interleukin-37 (IL-37) expression. Methods: Serum was collected from patients with gout (n = 40) and from healthy controls (n = 30). The mRNA and protein expression of target molecules IL-1b, IL-37, caspase-1, and Smad3 was measured in THP-1 cells stimulated with MSU, atorvastatin, or rosuvastatin using real-time quantitative polymerase chain reaction and Western blot assay. Transfection with IL-1b or Smad3 siRNA in THP-1 cells was used to verify the pharmaceutical effect of statins in uric acid-induced inflammation. Results: Serum IL-37 level in gout patients was significantly higher than in controls (p < 0.001) and was associated with serum uric acid level (r = 0.382, p = 0.008). THP-1 cells stimulated with MSU markedly induced IL-37 mRNA expression and transition of IL-37 from cytoplasm to nucleus. Recombinant IL-37 treatment dose-dependently inhibited activation of caspase-1 and IL-1b in MSU-induced inflammation. Atorvastatin and rosuvastatin attenuated caspase-1 activation and mature IL-1b expression but augmented translocation of IL-37 from cytoplasm to nucleus. Atorvastatin and rosuvastatin induced phosphorylation of Smad3 in THP-1 cells treated with MSU crystals. Statins potently attenuated translocation of IL-37 from cytoplasm to nucleus in THP-1 cells transfected with Smad3 siRNA compared to cells with negative control siRNA. Conclusion: This study revealed that statins inhibit MSU-induced inflammatory response through augmentation of phosphorylated Smad3-mediated IL-37 expression in THP-1 cells.

The recycling, incineration, and final disposal rate of municipal solid waste (MSW) are calculated based on the total amount of waste input to each facility in many countries. These statistic data have serious limitation in setting the national goal and policy for effective waste management because it is not considering the amount of foreign objectives in the process of each life-cycle stage. This case study is to estimate the actual rates of recycling, incineration, and final disposal by material flow analysis (MFA) after the collection of MSW in Korea. The actual rates of recycling, incineration and final disposal for MSW in 2016 were 49.9%, 32.9% and 23.1% respectively, indicating that the recycling rate was lower by 10.1%, while the incineration and final disposal rates were raised by 7.6% and 8.4% respectively, compared with the statistics for current MSW. In addition, the changed actual rates of recycling, incineration treatment, and final landfill, and variation of waste treatment charge according to treated amounts per treatment method was analyzed. This results of this study will contribute to establish national level of plan on effective waste management.

Achievement of solid fusion of the lumbosacral junction (L5-S1 level) is an important factor in adult spinal deformity (ASD) surgery. The purpose of this study is to explore the effectiveness and feasibility of injectable rhBMP-2 (a combination of Eschericia coli-derived rhBMP-2 and hydrogel type β-TCP carrier; NOVOSIS Inject) as a bone substitute for the fusion of lumbosacral junction. 20 patients (average age 69.1 years) diagnosed with ASD with sagittal imbalance who underwent surgical treatment including anterior lumbar interbody fusion (ALIF) in the L5-S1 level were evaluated. Injectable rhBMP-2 was applied in L5-S1 ALIF and followed-up for 1-year. Solid fusion rates and changes of clinical outcomes (Oswestry Disability Index [ODI], Visual Analog Scale [VAS] of back and leg) were measured and analyzed at 6 and 12 months after surgery. All postoperative adverse events were evaluated about the association with injectable rhBMP-2. Fusion rates were 68.4% and 100% at 6 and 12 months after surgery. Compared to baseline, ODI were improved to 45.8% and 63.7%, VAS(back) were improved to 69.2% and 72.8%, and VAS(leg) were improved to 49.2% and 64.8% at 6 and 12 months after surgery (p&lt;0.001, respectively). There were no adverse events associated with injectable rhBMP-2. Thus, injectable rhBMP-2 may be a suitable choice of a bone graft substitute when achieving solid interbody fusion in the lumbosacral junction.

OBJECTIVE: Although 3D-printed anatomic models are not new to medicine, the high costs and lengthy production times entailed have limited their application. Our goal was developing a new and less costly 3D modeling method to depict organ-tumor relations at faster printing speeds. METHODS: We have devised a method of 3D modeling using DICOM images. Coordinates are extracted at a specified interval, connecting them to create mesh-work replicas. Adjacent constructs are depicted by density variations, showing anatomic targets (ie, tumors) in contrasting color. RESULTS: An array of organ solid-tumor models were printed via Fused Deposition Modeling 3D printer at significantly less cost ($0.05/cm3) and time expenditure (1.73 min/cm3; both, p<.001). Printed models helped promote visual appreciation of organ-tumor anatomy and adjacent tissues. Our mesh-work 3D thyroidal prototype reproduced glangular size/contour and tumor location, readily approximating the surgical specimen. CONCLUSIONS: This newly devised mesh-type 3D printing method may facilitate anatomic modeling for personalized care and improve patient awareness during informed surgical consent.

Cell migration crucial contributor to metastasis, a critical process associated with the mortality of cancer patients. The initiation of metastasis is triggered by epithelial-mesenchymal transition (EMT), along with the changes of the expression of EMT marker proteins. Inflammation plays a significant role in carcinogenesis and metastasis. Lipopolysaccharide (LPS), a typical inflammatory agent, promoted the generation of superoxide through the activation of p-Tyr42 RhoA, Rho-dependent kinase 2 (ROCK2) and the phosphorylation of p47phox. In addition, p-Tyr42 RhoA activated phospholipase D1 (PLD1), with PLD1 and phosphatidic acid (PA) being involved in superoxide production. PA also regulated the expression of EMT maker proteins. Consequently, we have identified MHY9 (Miosin IIA, NMIIA) as a PA-binding protein in response to LPS. MYH9 also contributed cell migration and the alteration of the expression of EMT marker proteins. P-Tyr42 RhoA, PLD1 and MYH9 associated to form a complex, which was distributed in both the cytosol and nucleus. In addition, we have found that p-Tyr42 RhoA and PLD1 associated with the ZEB1 promoter. Taken together, we propose that p-Tyr42 RhoA and PLD1, responsible for producing PA, and PA-bound MYH9 are involved in the regulation of ZEB1 expression, thereby promoting cell migration.

We successfully designed an optimized plenum fan with a three-dimensional, smooth, curved blade. The optimized model revealed that the static pressure in the channel had been increased uniformly and stably, and the flow separation at the leading edge was significantly reduced. To conclude, the three-dimensional blade stabilized the fluid flow, and the flow friction was reduced by suppressing the flow separation as much as possible so that both the static pressure and the static efficiency were clearly improved in comparison with those of the original model. The static efficiency, as a result, was improved by 6% compared with that of the original model.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

This study entailed the design and analysis of a 400 m-class underwater glider operated by a bladder-type buoyancy engine. The underwater glider was designed for high-speed movement with a maximum velocity of 2 knots. The shape of the hull was designed to reduce water resistance using the Myring hull profile equation. The reliability was verified by performing simulations using resistance coefficients. The relationship between the control value of the ballast discharged from the buoyancy engine and the glider's speed according to the path angle was analyzed. Further, the relationship between the optimal glide angle and the design control value of the ballast was derived, and the optimal glider speed was estimated accordingly. Based on the analysis results, a bladder-type buoyancy engine was developed, and the maximum speed of the tested underwater glider was measured via sea trials.

This study was to investigate and assess salivary biomarkers as a means of diagnosing periodontitis. A total of 121 subjects were included: 28 periodontally healthy subjects, 24 with stage I, 24 with stage II, 23 with stage III, and 22 with stage IV periodontitis. Salivary proteins including active matrix metalloproteinase-8 (MMP-8), pro-MMP-8, total MMP-8, C-reactive protein, secretory immunoglobulin A and planktonic bacteria including Aggregatibacter actinomycetemcomitans, Porphyromonas gingivalis, Tannerella forsythia, Treponema denticola, Fusobacterium nucleatum, Prevotella intermedia, Porphyromonas nigrescens, Parvimonas micra, Campylobacter rectus, Eubacterium nodatum, Eikenella corrodens, Streptococcus mitis, Streptococcus mutans, Staphylococcus aureus, Enterococcus faecalis, and Actinomyces viscosus were measured from salivary samples. The performance of the diagnostic models was assessed by receiver operating characteristics (ROC) and area under the ROC curve (AUC) analysis. The diagnostic models were constructed based on the subjects’ proteins and/or microbial profiles, resulting in two potential diagnosis models, which achieved better diagnostic powers with an AUC value &gt; 0.750 for the diagnosis of stage II, III, and IV periodontitis (Model PC-I; AUC: 0.796, sensitivity: 0.754, specificity: 0.712) and for the diagnosis of stage III and IV periodontitis (Model PC-II; AUC: 0.796, sensitivity: 0.756, specificity: 0.868). This study can contribute to screening for periodontitis based on salivary biomarkers.

Multidrug resistant (MDR) bacteria have become a severe problem for public health. Developing new antibiotics for MDR bacteria is difficult, from inception to the clinically approved stage. Here, we have used a new approach; we have modified the antibiotic, ciprofloxacin (CFX), with triphenylphosphonium (TPP, PPh3) moiety via ester- (CFX-ester-PPh3) and amide-coupling (CFX-ester-PPh3), to target bacterial membranes. In this study, we have evaluated the antibacterial activities of CFX and its derivatives against 16 species of bacteria, including MDR bacteria, using minimum inhibitory concentration (MIC) assay, morphological monitoring, and expression of resistance-related genes. TPP-conjugated CFX, CFX-ester-PPh3 and CFX-amide-PPh3 showed significantly improved antibacterial activity against Gram-positive bacteria, Staphylococcus aureus, including MDR S. aureus (MRSA) strains. The MRSA ST5 5016 strain showed high antibacterial activity, with an MIC values of 11.12 µg/mL for CFX-ester-PPh3 and 2.78 µg/mL for CFX-amide-PPh3. The CFX derivatives inhibited biofilm formation in MRSA by more than 74.9% of CFX-amide-PPh3. In the sub-MIC, CFX derivates induced significant morphological changes in MRSA, including irregular deformation and membrane disruption, accompanied by a decrease in the level of resistance-related gene expression. With these promising results, this method is very likely to combat MDR bacteria, through a simple TPP moiety modification of known antibiotics, which can be readily prepared at clinical sites.

Phosphate (Pi) starvation is a critical factor limiting crop growth, development, and productivity. Rice (Oryza sativa) R2R3-MYB transcription factors function in the transcriptional regulation of plant responses to various abiotic stresses and micronutrient deprivation, but little is known about their roles in Pi starvation signaling and Pi homeostasis. Here we identified the R2R3-MYB transcription factor gene OsMYB58, which shares high sequence similarity with AtMYB58. OsMYB58 expression was induced more strongly by Pi starvation than by other micronutrient deficiencies. Overexpressing OsMYB58 in Arabidopsis thaliana and rice inhibited plant growth and development under Pi-deficiency conditions. In addition, overexpression of OsMYB58 in plants exposed to Pi deficiency strongly affected root development, including seminal root, lateral root, and root hair formation. Overexpressing OsMYB58 strongly decreased the expression of the rice microRNAs, OsmiR399a and OsmiR399j. By contrast, overexpressing OsMYB58 strongly increased the expression of rice PHOSPHATE 2 (OsPHO2), whose expression is repressed by miR399 during Pi starvation signaling. OsMYB58 functions as a transcriptional repressor of the expression of its target genes, as determined by a transcriptional activity assay. These results demonstrate that OsMYB58 negatively regulates OsmiR399-dependent Pi starvation signaling by enhancing OsmiR399s expression.

Objective: The purpose of this study was to determine if Porphyra tenera extract (PTE) has immune-enhancing effects and is safe in healthy adults. Methods: Subjects (3x10³ ≤ peripheral blood leukocyte levels < 8x10³ cells/μl) who met the inclusion criteria were recruited for this study. Enrolled subjects (n=120) were randomly assigned to either the PTE group (n=60) who were given 2.5 g/day of PTE (as Porphyra tenera extract) in capsule form or the placebo group (n=60) who were given crystal cellulose capsules with the identical appearance, weight, and flavor as the PTE capsules for 8 weeks. Outcomes were assessed by measuring natural killer cell (NK-cell) activity, cytokines, and upper respiratory infection (URI), and safety parameters were assessed at baseline and 8 weeks. Results: Compared to baseline, NK cell activity (%) increased for all effector cell to target cell ratios in the PTE group after 8 weeks, but there were no changes in the placebo group (p<0.1). Subgroup analysis of 101 subjects without an URI revealed that NK-cell activity in the PTE group tended to be increased for all E:T ratios (E:T=12.5:1 p=0.068; E:T=25:1 p=0.036; E:T=50:1 p=0.081) compared to the placebo group. There was a significant difference between these two groups for the E:T=25:1 ratio, which increased from 20.3±12.0% at baseline to 23.2±12.4% after 8 weeks in the PTE group (p=0.036). There was no significant difference in levels of cytokines between these two groups. Conclusions: PTE supplementation appears to enhance immune function by improving NK-cell activity without adverse effects in healthy adults.

As renewable energy generation prediction systems have been introduced into the energy trading market, accurate prediction of solar photovoltaic (PV) energy generation has become a crucial challenge for ensuring stable trade of variable energy. Therefore, it is essential to quantitatively investigate and analyze current prediction technology and develop more advanced prediction systems. In this study, three models for predicting PV energy generation were investigated. Multiple regression, random forest, and gradient boosting machine (GBM) models were con-structed for 15 utility-scale power plants throughout South Korea. Model performance was evaluated in terms of root mean square error (RMSE) and mean absolute error (MAE). The multiple regression-based model had an RMSE of 12.00% and MAE of 9.06%. The random forest model had an RMSE of 11.69% and MAE of 8.61%. The GBM model had an RMSE of 11.34% and MAE of 8.18%, indicating its superior accuracy among the three models in predicting PV energy generation. These findings provide valuable insights that may contribute to the development of advanced PV energy generation models and their application in grid operations.

There is a lack of data comparing sugammadex with anticholinesterase for the quality of anaesthesia recovery, especially following a single bolus dose of rocuronium. Thus, we evaluated the influence of reversal with sugammadex or neostigmine on post-operative quality of recovery by using the Post-operative Quality Recovery Scale (PQRS). A total of 86 patients undergoing trans-pars plana vitrectomy (TPPV) under general anaesthesia were intubated following a single bolus dose of rocuronium (0.6 mg/kg). At the end of surgery, patients were received either neostigmine or sugammadex. The quality of recovery was assessed using the PQRS at 15 minutes and 40 minutes after surgery, and on post-operative day 1. The recovery rate in the physiological domain was higher in the sugammadex group at 15 minutes after surgery (P = 0.02). Though there were no significant differences in the overall cognitive recovery domain, patients in the sugammadex group could recall more numbers in reverse order. However, there were no significant differences between the groups in the other domains of the PQRS. The use of sugammadex may increase the quality of the post-operative physiological recovery at early post-operative periods compared with neostigmine use following a single bolus dose of rocuronium in patients undergoing TPPV with general anaesthesia.

The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

Cervical cancer, primarily caused by high-risk human papillomavirus (HR-HPV) types 16 and 18, is a major global health concern. Persistent HR-HPV infection can progress from reversible pre-cancerous lesions to invasive cervical cancer, which is driven by the oncogenic activity of human papillomavirus (HPV) genes, particularly E6 and E7. Traditional screening methods, including cytology and HPV testing, have limited sensitivity and specificity. This review explores the ap-plication of p16/Ki-67 dual-staining cytology for cervical cancer screening. This advanced im-munocytochemical method allows for simultaneously detecting p16 and Ki-67 proteins within cervical epithelial cells, offering a more specific approach for triaging HPV-positive women. Dual staining and traditional methods are compared, demonstrating their high sensitivity and negative predictive value but low specificity. The increased sensitivity of dual staining results in higher detection rates of CIN2+ lesions, which is crucial for preventing cervical cancer progression. However, its low specificity may lead to increased false-positive results and unnecessary biopsies. The implications of integrating dual staining into contemporary screening strategies, particularly considering the evolving landscape of HPV vaccination and changes in HPV genotype prevalence are also discussed. New guidelines and further research are necessary to elucidate the long-term effects of integrating dual staining into screening protocols.

Various peptides or non-structural amino acids are recognized by their specific target proteins and perform biological role in various pathways in vivo. Understanding the interactions between target protein and peptides (or non-structural amino acids) provides key information on the molecular interactions, which can be potentially translated to the development of novel drugs. However, it is experimentally challenging to determine the crystal structure of protein-peptide complexes. To obtain structural information on substrate recognition of peptide-recognizing enzyme, X-ray crystallographic studies were performed using triglycine (Gly-Gly-Gly) as main-chain of peptide. The crystal structure of Parengyodontium album Proteinase K in complex with triglcyine was determined at 1.4 Å resolution. Two different bound conformations of triglycine were observed at the substrate recognition site. The triglycine backbone forms stable interactions with β5-α4 and α5-β6 loops of main-chain. One of the triglycine-binding conformations was identical with the binding mode of a peptide-based inhibitor from a previously reported crystal structure of Proteinase K. Triglycine has potential application X-ray crystallography to identify substrate recognition sites in peptide binding enzymes.

Croton L. (Euphorbiaceae) is a very specious genus and consists of about 1,250 species, mainly distributed in tropical Asia and China. The first complete plastome sequence from the genus, Croton tiglium, is reported in this study (NCBI acc. No. MH394334). The plastome is 150,021 bp in length. The lengths of LSC and SSC are 111,654 bp and 18,167 bp, respectively. However, the length of the IR region is only 10,100 bp and includes only four rrn and four trn genes, and a small part of the ycf1 gene. We propose two-step IR contractions to explain this unique IR region of the C. tiglium plastome. First, the IR contracted from rps19-rpl2 to ycf2-trnL-CAA on the LSC/IRb boundary. Second, the IR contracted from ycf2-trnL-CAA to rrn16-trnV-GAC on the LSC/IRa boundary. In addition, duplicated copies of psaI genes were discovered in the C. tiglium plastome. Both copies were located side by side between accD and ycf4 genes, but one copy was pseudogenized because of a five-basepair (TAGCT) insertion in the middle of the gene following frameshift mutation. The plastome contains 112 genes, of which 78 are protein-coding genes, 30 are tRNA genes, and four are rRNA genes. Sixteen genes contain one intron and two genes have two introns. The infA gene is lost. Twelve large repeats were detected in the plastome. All large repeats are located in the LSC region. Also, 272 simple sequence repeats (SSRs) were identified. The penta-SSRs accounted for 45% of total SSRs, followed by mono- (32%), di- (12%), tetra (6%) and tri-SSRs (5%). Most of them were distributed in the large single copy (LSC) region (85%). In addition, 76% of the SSRs were located in the intergenic spacer (IGS). Phylogenetic analysis suggested that C. tiglium is a sister group of Jatropha curcas with 100% bootstrap support. Seven Euphorbiaceae species formed one clade with 100% bootstrap support.

As renewable energy generation prediction system has been introduced into the energy trading market, making a model to accurately predict the quantity of solar photovoltaic (PV) energy generation has become a significant problem. Moreover, to encourage an accurate prediction of the quantity of energy generation, an incentive system has been implemented for those who predict the quantity of solar PV energy under the error rate of 8%. Therefore, it has become more important to investigate and analyze current prediction technology numerically and develop more advanced prediction system. In this study, we tried to develop a better model to improve the accuracy of solar PV energy generation quantity by comparing three models made with gradient boosting machine (GBM), Model 1, Model 2, Model 3 respectively. Model 1 was built with the whole training data set without any additional preprocessing. After conducting some additional preprocessing procedure to predict solar energy generation more accurately, we made Model 2 with the whole training data set and Model 3 with only upper 10% of energy generation capacity. To compare the accuracy of three models, normalized mean absolute error (nMAE) was used as an evaluation index. The nMAE of Model 1 was 9.64% while the Model 2 showed 8.41%. Also, Model 3, which was constructed with the training set of upper 10% energy generation capacity, outperformed with the nMAE of 8.08%. For further study, to check the effectiveness of models constructed with GBM, a time series model, autoregressive integrated moving average (ARIMA), was also built and the nMAE was compared.

Changes in crude oil price affect the shipping freight market in three different channels. This study explores the dependence structure between oil prices and maritime freight rates to identify the strongest channel. Therefore, it investigates the relationship between oil prices and three major maritime freight rates; the Baltic Dry Index (BDI), the Baltic Dirty Tanker Index (BDTI), and the Baltic Clean Tanker Index (BCTI). We employ the decomposition method, not studied in the existing literature. The copula approach identifies the time-varying effects and asymmetry in the tail dependence structure between oil prices and freight rates. The main results of this analysis are as follows. The decomposed components display different conditional dependence patterns, and asymmetry is revealed in the upper and lower tail dependence. In the long run, we find more dependence in extreme periods like the financial crises. In short-run fluctuations, we find the dependence increases in an economic boom. The implications of the results suggest that dependence can vary over time and may change depending on extreme events, implying that the complementary strategies of the long run and short run should be different.

Bone morphogenetic proteins (BMPs), belonging to the transforming growth factor-β superfamily, regulate many cellular activities including proliferation and neovascularization. The use of recombinant human bone morphogenic protein 2 (rh-BMP 2) in oral and maxillofacial surgery has seen a tremendous increase, especially with bone grafting materials to promote bone reconstruction processes; even though its interactions with the other essential processes in the human tissues are still not fully clear. investigating the effect of administrating rh-bmp2 on the clinical values of the gingival cell proliferation index Ki67 marker expression in the gingival tissue in comparison with normal human gingival tissue. The study includes 2 groups in a randomized controlled Clinical Trial: 40 gingival samples; 20 normal and 20 have been treated with 0.25µg of rh-BMP2 during dental implantation in the posterior mandible area, taken 3 months later in the time of healing abutments installation using a tissue puncher. Samples will be stained with hematoxylin-eosin and immunohistochemically. The expression of Ki67 will be measured in one way: the number of cells that express the marker. The comparison between groups will be done using One -a way ANOVA test in the numerical data SPSS 17.0 will be used as software. Differences would be considered significant at P=0.05. It is considered that rh-BMP2 can improve gingival tissue proliferation in patients undergoing dental implant treatment, and indicates better healing.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

Rice is an important cereal crop worldwide, the growth of which is affected by rice blast disease, caused by the fungal pathogen Magnaporthe oryzae. As climate change increases the diversity of pathogens, the disease-resistance genes (R genes) in plants must be identified. The major blast-resistance genes have been identified in indica rice varieties; therefore, japonica rice varieties with R genes now need to be identified. Because leucine-rich repeat (LRR) domain proteins possess R-gene properties, we used bioinformatics analysis to identify the rice candidate LRR domain receptor-like proteins (OsLRR-RLPs). OsLRR-RLP2, which contains six LRR domains, showed differences in the DNA sequence, containing 43 single-nucleotide polymorphisms (SNPs) in indica and japonica subpopulations. The results of M. oryzae inoculation analysis indicated that indica varieties with partial deletion of OsLRR-RLP2 showed susceptibility, whereas japonica varieties with intact OsLRR-RLP2 showed resistance. oslrr-rlp2 mutant generated using clustered regularly interspaced palindromic repeats (CRISPR)/CRISPR-associated protein 9 (Cas9) showed increased pathogen susceptibility, whereas plants overexpressing this gene showed pathogen resistance. These results indicate that OsLRR-RLP2 confers resistance to rice, and OsLRR-RLP2 may be useful for breeding resistant cultivars.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

The causal effects of chondroitin, glucosamine, and vitamin/mineral supplement intake on kidney function remain unknown, despite being commonly used. We conducted a two-sample summary-level Mendelian randomization (MR) analysis to test for causal associations between regular dietary supplement intake and kidney function. Genetic instruments for chondroitin, glucosamine, and vitamin/mineral supplement intake were obtained from genome-wide association study of European ancestry. Summary statistics for the log-transformed estimated glomerular filtration rate (log-eGFR) were provided by the CKDGen consortium. The multiplicative random-effects inverse variance-weighted method showed that genetically predicted chondroitin and glucosamine intake was causally associated with a lower eGFR (chondroitin, eGFR change beta = -0.113 %, standard error (SE) = 0.03 %, P-value = 2E-04; glucosamine, eGFR change beta = -0.240 %, SE = 0.035 %, P-value = 6E-12). However, a genetically predicted vitamin/mineral supplement intake was associated with a higher eGFR (eGFR change beta = 1.426 %, SE = 0.136 %, P-value = 1E-25). Validation analyses and pleiotropy-robust MR results for chondroitin and vitamin/mineral supplement intake supported the main results. Our MR study suggests a potential causal effect of chondroitin and glucosamine intake on kidney function. Therefore, clinicians should carefully monitor their long-term effects.

A new study for CH4 reforming to hydrogen and hydrogen storage was performed using magnesium-based alloy. MgH2-12Ni (with the composition of 88 wt% MgH2 + 12 wt% Ni) was prepared in a planetary ball mill by milling in hydrogen atmosphere (reaction-involved milling). X-ray diffraction (XRD) analyses were performed for the samples after reaction-involved milling and after reactions with CH4. The variation of adsorbed or desorbed gas with time was measured by a Sieverts’ type high-pressure apparatus at 773 K. The microstructures of the powders were observed using scanning transmission microscope (STEM) with energy-dispersive X-ray spectroscopy (EDS). The synthesized samples were also characterized using Fourier Transform Infrared (FT-IR) spectroscopy. XRD pattern of MgH2-12Ni after reaction with CH4 of 12 bar at 773 K and decomposition under 1.0 bar at 773 K exhibited phases of MgH2 and Mg2NiH4. This shows that reforming of CH4 was occurred, hydrogen produced after reforming of CH4 was then adsorbed on the particles, and hydrides were formed during cooling to room temperature. Ni and Mg2Ni formed during heating up to 773 K are believed to have brought about catalytic effects for reforming CH4. MgH2-12Ni adsorbed 0.8 wt% reformed CH4 within 1 min in a reaction with CH4 of 12 bar at 773 K and then desorbed 0.8 wt% reformed CH4 (hydrogen-containing mixture) within 1 min under 1 bar at 773 K. Attenuated total reflectance FT-IR spectroscopy (ATR-FTIR) spectra of MgH2-12Ni after reactions under 12 bar CH4 at 723 K and 773 K showed peaks of C-H bending, C=C stretching, O-H stretching, O-H bending, and C-O stretching.

Serial femtosecond crystallography (SFX) using an X-ray free-electron laser (XFEL) enables determination of room-temperature structures without causing radiation damage. Using an optical pump-probe or mix-and-injection, SFX enables the intermediate state visualization of a molecular reaction. In SFX experiments, serial and stable microcrystal delivery to the X-ray interaction point is vital for reasonable data collection and efficient beam time. The Pohang Accelerator Laboratory X-ray Free Electron Laser (PAL-XFEL) facility established SFX instruments at a nanocrystallography and coherent imaging (NCI) experimental station. Various sample delivery methods, including injection, fixed-target scanning, and hybrid methods, have been developed and applied to collect XFEL diffraction data. Herein, we review the currently available sample delivery methods for SFX at the NCI experimental station at the PAL-XFEL. This article will help PAL-XFEL users access the SFX system for their experiments.

Pericytes are increasingly recognized as being important in the control of blood-brain barrier permeability and vascular flow. Research on this important cell type has been hindered by widespread confusion regarding the phenotypic identity and nomenclature of pericytes and other perivascular cell types. In addition, pericyte heterogeneity and mouse-human species differences have contributed to confusion. Herein we summarize our present knowledge on the identification of pericytes and pericyte subsets in humans, primarily focusing on recent findings in humans and nonhuman primates. Precise identification and definition of pericytes and pericyte subsets in humans may help us to better understand pericyte biology and develop new therapeutic approaches specifically targeting disease-associated pericyte subsets.

Recent progress in the fabricating flexible electronics has been developed significantly due to the increased interest of the flexible electronics which can be applied to enormous fields not only to conventional electronic devices but to bio/eco electronic devices. Flexible electronics can be applied to wide range of fields such as flexible display, flexible power storage, flexible solar cells, wearable electronics and healthcare monitoring devices. Recently, flexible electronics are being attached on the skin and even implanted into human body to monitor the bio-signals and for treatment purpose. To improve the electrical characteristic and the mechanical properties of flexible electronics, nanoscale fabrications using novel nano-materials are required. Advanced in nanoscale fabrication methods allow construction of the active materials that can combine with the ultra-thin soft substrate to form flexible electronics with high performances and reliability. In this review, wide range of nanoscale fabrication methods for flexible electronics classified in either top-down or bottom-up approaches such as conventional photolithography, soft lithography, nanoimprint lithography, growth, assembly and chemical vapor deposition(CVD) will be reported with specific fabrication processes and results. Here, our aim is to introduce various fabrication methods that can be used to fabricate the flexible electronics.

Introduction: This study explored the structural relationship between peer relations, exercise participation satisfaction, exercise commitment, and adherence to intention to exercise among Korean sports club participants. The objective was to offer insights that can enhance intentions for continuous exercise participation. Methods: To fulfill this objective, data were gathered using snowball sampling from teenagers at middle schools in Seoul and Gyeonggi, South Korea, who either currently participate in school sports clubs or have participated in the past. A total of 261 responses were analyzed using frequency, technical statistics, and confirmatory factor, reliability, correlation, and structural equation model analyses. Results: Through these analyses, this study found that peer relationships, exercise participation satisfaction, and exercise commitment were significant as both direct and indirect influences on exercise adherence intentions. Discussion: Intervention strategies should focus on fostering the positive emotions that stem from peer relationships.

We analyze the upside and downside risk connectedness among international stock markets. We characterize the connectedness among international stock returns using the Diebold and Yilmaz spillover index approach and compute the upside and downside value-at-risk. We document that the connectedness level of the downside risk is higher than that of the upside risk and that stock markets are more sensitive when the stock market declines. We also find that specific periods (e.g., the global financial crisis, the European debt crisis, and the COVID-19 turmoil) intensify the spillover effects across international stock markets. Our results demonstrate that the EU, Ger-many, and the US acted as net transmitters of dynamic connectedness; however, Japan (JP), China (CH), and India (IN) acted as net receivers of dynamic connectedness during the sample period. These findings provide significant new information to policymakers and market participants.

Radar observation data with high temporal and spatial resolution are used in the data assimilation experiment to improve precipitation forecast of a numerical model. The numerical model considered in this study is Weather Research and Forecasting (WRF) model with double-moment 6-class microphysics scheme (WDM6). We calculated radar equivalent reflectivity factor using higher resolution WRF and compared with radar observations in South Korea. To compare the precipitation forecast characteristics of three-dimensional variational (3D-Var) assimilation of radar data, four experiments are performed based on different precipitation types. Comparisons of the 24-h accumulated rainfall with Automatic Weather Station (AWS) data, Contoured Frequency by Altitude Diagram (CFAD), Time Height Cross Sections (THCS), and vertical hydrometeor profiles are used to evaluate and compare the accuracy. The model simulations are performed with and with-out 3D-VAR radar reflectivity, radial velocity and AWS assimilation for two mesoscale convective cases and two synoptic scale cases. The radar data assimilation experiment improved the location of precipitation area and rainfall intensity compared to the control run. Especially, for the two convective cases, simulating mesoscale convective system was greatly improved.

Liver cirrhosis is one of the most prevalent chronic liver diseases worldwide. In addition to viral hepatitis, genetic conditions such as steatohepatitis, autoimmune hepatitis, sclerosing cholangitis, and Wilson’s disease can also lead to cirrhosis. Moreover, alcohol can cause cirrhosis on its own and exacerbate chronic liver disease from other causes. The treatment of cirrhosis can be divided into addressing the cause of cirrhosis and reversing liver fibrosis. To this date, there is still no clear consensus on the treatment of cirrhosis. Recently, there has been a lot of interest in potential treatments that modulate the gut microbiota and gut-liver axis for the treatment of cirrhosis. According to recent studies, modulation of the gut microbiome by probiotics ameliorates the progression of liver disease. The precise mechanism for relieving cirrhosis via gut microbial modulation has not been identified. This paper summarizes the role and effects of the gut microbiome in cirrhosis based on experimental and clinical studies on absorbable antibiotics, probiotics, prebiotics, and synbiotics. Moreover, it provides evidence of a relationship between the gut microbiome and liver cirrhosis.

Accumulating reports have suggested that an inability to clear dead cells is a cause of inflammation and cancer and that the fascia is associated with cancer metastasis. Novel corpuscle-connected filiform structures (CCFSs) entangled on the fascia of the internal organs of rats were selectively visualized with high repeatability (93%) under vital staining with Janus Green B (JGB). Serial sections of CCFSs stained with haematoxylin and eosin and with Mattson Trichrome were microscopically examined. In parallel, the immunohistochemistry with CD31, Lyve 1, scanning electron microscopy, and transmission electron microscopy (TEM) were also used to investigate the novel properties of the CCFSs. All of the CCFSs enclosed JGB-stained granules, which was verified by the impromptu coupling of stereo and light microscopes and fluorescence-activated cell sorting. The functions of the CCFSs were discovered under fluorescence microscopy and confocal laser scanning microscopy to be implicated in cell death: fragmented DNAs and f-actins with extracellular DNAs. The dead cells in the CCFSs were verified by using terminal deoxynucleotidyl transferase dUTP nick end labelling and TEM. Moreover, the CCFS had a relatively-high concentration of calcium, a main element for cell death in tissue, which was measured in 2-dimensionally images using time-of-flight secondary ion mass spectrometry. Taken these results, we report for the first time that novel reticular CCFSs are widely entangled on the fascia of the internal organs of rats with the implication for cell death.

Porcine epidemic diarrhea (PED) is a swine wasting disease caused by coronavirus infection. It causes great economic damage to the swine industry worldwide. Despite the continued use of vaccines, PED outbreaks continue, highlighting the need to review the effectiveness of current vaccines and develop additional vaccines based on new platforms. Here, we review existing vaccine technologies for preventing PED and highlight promising technologies that may help control PED virus in the future.

1) Background: In service business areas, design enhances the customer experience through the elements which anticipate specific emotional responses of customers. Many service companies are keen to develop and examine design elements from the customer perspective. Furthermore, recently, having considered the significance of customers’ emotional responses by design elements, categorising design elements into manageable dimensions can facilitate the evaluation of design elements. However, design elements and dimensions of design value are not defined in the current service marketing literature, and companies need a measurement tool and managerial guideline to their innovative value creation and compelling service delivery. For these reasons, this research aims to categorise the design value dimensions and propose the managerial implication for the innovative use of design; 2) Methods: This study used the mixed methodology; two stages of interviews and SEM (Structural Equation Modelling); 3) Results: Interview analyses facilitate the identification of design elements in the service delivery process. SEM results underpin the relevance of the categorised design elements and their impact on customer loyalty by comparing different groups (country and time elapsed from experience); and 4) Conclusions: Findings are the fundamentals of developing measuring tool for design and trigger future studies for conceptualising intangible assets.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

We introduce a novel microscopic image dataset augmented with segmentation and detection labels specifically designed for microplastic analysis in sewage environments. Recognizing the increasing concern over microplastics — particles of synthetic polymers smaller than 5mm — and their detrimental effects on marine ecosystems and human health, our research focuses on enhancing detection and analytical methodologies through advanced computer vision and deep learning techniques. The dataset comprises high-resolution microscopic images of microplastics collected from sewage, meticulously labeled for both segmentation and detection tasks, aiming to facilitate accurate and efficient identification and quantification of microplastic pollution. In addition to dataset development, we present example deep learning models optimized for segmentation and detection of microplastics within complex sewage samples. The models demonstrate significant potential in automating the analysis of microplastic contamination, offering a scalable solution to environmental monitoring challenges. Furthermore, we ensure the accessibility and reproducibility of our research by making the dataset and model codes publicly available, accompanied by detailed documentation on GitHub and LabelBox. The dataset and example deep learning models are publicly available at the following GitHub link. https://anonymous.4open.science/r/Microplastics-in-Sewage-1BEF

Since the college years represent an important period for forming oral health behaviors during adulthood, it is important that college students establish proper oral health-promoting behaviors. Therefore, this study aims to identify the effects of oral health education experience, knowledge, and practice behaviors on oral health care self-efficacy among college students, as studies related to this topic are scarce. A total of 236 college students participated in a questionnaire survey comprising 21 questions. The collected data were analyzed through a chi-square test, independent-samples t-test, and logistic regression analysis using SPSS version 22.0. Participants with oral health education experience showed higher levels of oral health knowledge and practice behaviors than those who did not, and the odds of them having oral health care self-efficacy was 3.743 higher. Moreover, a one-unit increase in oral health knowledge and practice behaviors was associated with a 1.199 and 1.351 increase in oral health care self-efficacy, respectively. For oral health promotion among college students, oral health care self-efficacy reinforcement programs tailored to college students should be developed. These should focus on expanding oral health education opportunities to promote improvement in oral health care self-efficacy by strengthening oral health knowledge and the motivation to practice oral health behaviors.

Silica aerogels and their derivatives have outstanding thermal properties with exceptional values in the thermal insulation industry. However, the brittle nature restricts its large-scale commercialization. Thus, enhancing their mechanical strength without affecting their thermal insulating properties is essential. Therefore, for the first time, highly thermally stable Poly(acrylamide-Co-acrylic acid) partial sodium salt is used as a reinforcing polymer to synthesize hybrid P(AAm-CO-AAc)-silica aerogels via epoxy ring-opening polymerization in the present study. Functional groups in P(AAm-CO-AAc) partial sodium salts, such as CONH2 and COOH, acted as nucleophiles for the epoxy ring-opening reaction with (3-glycidyloxypropyl)trimethoxysilane, which resulted in a seven-fold enhancement in mechanical strength compared to that of a pristine silica aerogel while maintaining the thermal conductivity at less than 30.6 mW/mK and porosity of more than 93.68%. Moreover, the hybrid P(AAm-CO-AAc)-silica aerogel demonstrated improved thermal stability up to 343 ⁰C owing to the synergetic effect between P(AAm-CO-AAc) and the silica aerogel, corresponding to thermal stability and strong covalent bonding among them. These excellent results illustrate that this new synthetic approach for producing hybrid P(AAm-CO-AAc)-silica aerogels is useful for enhancing the mechanical strength of a pristine silica aerogel without impairing its thermal insulating property and shows potential as an industrial heat insulation material.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

Pseudolysimachion nakaianum (Ohwi) T.Yamaz. is an endemic species that is an important species in the forest ecosystems of South Korea. This study aimed to develop an in vitro propagation system for P. nakaianum, to enhance the availability of this rare and endemic plant for commercial horticulture and restoration efforts. We utilized cotyledon explants from in vitro germinated seeds and two types of explants (petiole and leaf) from in vitro seedlings to assess the impact of five different cytokinins on adventitious shoot organogenesis in P. nakaianum. The half-strength Murashige and Skoog (MS) medium, supplemented with 10 µM thidiazuron (TDZ) for both cotyledon and petiole explants, yielded the highest shoot induction rates (61.1 ± 9.6% and 26.7 ± 8.8%, respectively) and the greatest number of shoots (3 ± 0.6 and 4.4 ± 0.5, respectively). Responses from leaf explants were variable, with none showing in vitro regeneration. Successfully acclimatized P. nakaianum plantlets in a greenhouse demonstrated normal growth. This protocol outlines an effective method for the direct in vitro regeneration from cotyledon and petiole explants of P. nakaianum, providing valuable information for the conservation of this species.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

In urban areas, deep excavation-induced ground deformation may damage adjacent existing structures and is conventionally evaluated by levelling at installed settlement points. However, a small number of measurements cannot represent the total change in ground deformation adjacent to excavation sites. Furthermore, significant local subsidence may occur in places where settlement points have not been installed and only noticed after an accident. For deep excavation sites located in urban areas, paved pedestrian sidewalks are often located adjacent to sites, and construction activity can cause these paving blocks to displace. This study introduces a method to detect paving block displacement adjacent to deep excavation sites using terrestrial photogrammetry. A digital camera creating point cloud data (PCD) and an acquisition method satisfying the frontal and side overlap requirements were demonstrated. To investigate the displacement detection and measurement capabilities by PCD analysis, an experimental program was conducted, including a PCD comparison containing the uplift, settlement, and horizontal paving block displacement and reference data. The cloud-to-cloud distance computation algorithm was adopted for PCD comparison. Paving block displacement was detected for displacements of 5, 7.5, and 10 mm in the uplift, settlement, and horizontal directions; however, the horizontal displacements were less clear. PCD analysis enabled satisfactory measurements between 0.024 and 0.881 mm for the vertical-displacement cases, but a significant error was observed for the horizontal-displacement cases owing to the cloud-comparison algorithm. The measurement blind spot of limited settlement points was overcome by the proposed method that detected and measured paving block displacement adjacent to excavation sites.

The aim of this work is to study the phase transformations, microstructures and mechanical properties of the martensitic stainless steel (MSS) 410 deposits produced by laser powder-directed energy deposition (LP-DED) additive manufacturing. The LP-DED MSS 410 deposits underwent the post heat treatment in austenitizing at 980℃ for 3hrs and followed by different tempering treatment at the temperatures of 250, 600, and 750℃ for 5hrs, respectively. The analyses of phase transformations and microstructural evolutions of LP-DED MSS 410 were carried out using X-ray diffraction, SEM-EDS, and EBSD. Vickers hardness and tensile strength properties were also measured to analyze the effects of the different tempering heat treatments. It reveals that as-built MSS 410 has very fine lath martensite and high hardness of about 480HV1.0 and tensile strength of about 1280 MPa, but elongation was very lower than the post heat treated ones. Precipitations of chromium carbide (Cr23C6) were most commonly observed at the grain boundaries and the entire matrix at the tempering temperatures of 600℃ and 750℃. In general, the tensile strengths de-creased from 1381MPa to 688MPa as tempering temperatures increased up to 750℃ from 250℃. Additionally, as the tempering temperature increased, the chromium carbide and tempered mar-tensite structures became coarser.

Perfluorinated compounds (PFCs) are used in the manufacturing process of the semiconductor and display industries, and the need for emission reduction is growing as a greenhouse gas with a very large global warming potential. The decomposition characteristics of etch type and water film (WF) type plasma-wet scrubbers were investigated. The PFCs used in the study were CF4, SF6, NF3, CHF3, C2F6, C3F8, and C4F8, and the destruction removal efficiency (DRE) and by-product gas generation rate according to the changes in the parameters (total flow rate and power) of the plasma-wet scrubber were confirmed. When the total flow rate was 100 L/min and the measured maximum power (11 kW), the reduction efficiency of CF4 in the etch type was 95.60 % and the DRE of other PFCs was 99.99 %. And, in the WF type, the DRE of CF4 was 90.06 %, that of SF6 was 96.44 %, and that of other PFCs was 99.99 %. When the total flow rate was 300 L/min and 11 kW, the DRE of SF6 in the etch type was 99 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. And, in the WF type, the DRE of SF6 was 94.39 %, and the DRE of NF3, CHF3, C2F6, C3F8, and C4F8 were 99.80 %, 95.34 %, 85.38 %, 88.49 %, and 98.22 %, respectively. The by-product gas generation rate was significantly lower in the WF type.

Abstract: This study estimates consumers’ willingness to pay (WTP) for sustainability turfgrass attributes such as low-input and stress-tolerance attributes, while considering potential trade-off relationships between aesthetic attributes and sustainability attributes. To address our objectives, our study conducts a choice experiment and estimates two mixed logit models. The first model includes low-input, winter kill, and shade-tolerance attributes as predictor variables, and the second model extends the first model by adding interaction terms between aesthetic and sustainability attributes. Another choice experiment is conducted under water policies with various water rate increase and watering restriction scenarios. Results from the mixed logit models show that overall, higher low-input cost reduction, less winter-damaged, and more shade-tolerance grasses are preferred, the direct effect of aesthetic attributes on consumers’ preference is strong, but the indirect effect represented by the interaction terms are generally statistically insignificant. Our results indicate that consumers like to have a pretty lawn, but no strong consideration is given to the aesthetics of their lawn when selecting low-input and stress-tolerance turfgrasses. Our choice experiment under water policy scenarios suggests that water pricing is more effective than watering restriction in increasing consumer demand for water-conserving turfgrasses.

This study aimed to investigate the effects of lupin flake supplementation on the growth, plasma parameters, carcass characteristics, and meat composition of late-fattening Hanwoo steers. The steers (n = 40) were randomly divided into the four groups with 10 steers each: LP0 (Lupin flake 0%), LP3 (lupin flake 3%), LP6 (Lupin flake 6%), and LP9 (lupin flake 9%). The total digestible nutriant intake increased as the concentration of lupin increased (linear and quadratic effects; P &lt; 0.05). The thiobarbituric acid-reactive substance content in the strip loins decreased as lupin flake supplementation levels increased (linear and quadratic effects; P &lt; 0.05), while carnosine levels increased linearly (P &lt; 0.05). As the lupin flake supplementation level increased, anserine and creatinine contents increased linearly and quadratically (P &lt; 0.05). Similarly, adenosine triphosphate (ATP) and adenosine monophosphate (AMP) contents increased with increasing lupin flake supplementation levels in linear and quadratic effects (P &lt; 0.001). Palmitoleic acid content increased significantly with increasing lupin flake supplementation level (linear and quadratic effects; P &lt; 0.05). The content of oleic acid in the strip loin was not significant, but the unsaturated fatty acid (UFA) (P &lt; 0.05) and n-6/n-3 ratio (P &lt; 0.05) increased. The results of this study indicated that although lupin flake supplementation did not markedly affect the growth, carcass characteristics, or meat composition of late-fattening Hanwoo steers, it exerted a positive effect on the flavor, taste profiles (anserine, creatinine, ATP, and AMP), hypotonicity(TBARS), and healthy meat production (UFA and n-6/n-3 ratio) related to beef.

Antimicrobial peptides (AMPs) have emerged as a promising solution to tackle bacterial infections and combat antibiotic resistance. However, their clinical application has been hindered by their vulnerability to protease degradation and toxicity towards mammalian cells. To overcome these challenges, our study aims to develop a method to enhance the stability and safety of AMPs, applicable to effective drug-device combination products. KR12 antimicrobial peptide was chosen and in order to further enhance its delivery and efficacy, HIV TAT protein-derived cell-penetrating peptide (CPP) was fused to form CPP-KR12. A new product, CPP-KR12@Si, was developed by forming silica nanoparticles with self-entrapped CPP-KR12 peptide using the biomimetic silica precipitability due to its cationic nature. Peptide delivery from CPP-KR12@Si to bacteria and cells was delivered at a slightly delayed rate with improved stability against trypsin treatment and a reduction in cytotoxicity over CPP-KR12. Finally, the antimicrobial potential of CPP-KR12@Si/bone graft substitute (BGS) combination product was demonstrated, which is coated with CPP-KR12 in the form of nanoparticles on the surface of BGS. Self-entrapped AMP in silica nanoparticles is a safe and effective AMP delivery method that will be useful for developing a drug/device combination product for tissue regeneration.

Many studies on flexible strain and pressure sensors have been reported due to growing interest in wearable devices for healthcare. However, most are fabricated with multiple ingredients and complicated methods even though commercial textiles, such as cotton, nylon, polyester, and silk were used. Here we present flexible pressure and strain (motion) sensors prepared with only graphene oxide (GO) and commercial silk fabrics and yarns. The pressure sensors were fabricated by simply dipping the silk fabric into GO solution followed by thermal treatment at 400 °C for reduction of GO (rGO). The pressure sensors were made from rGO-coated fabrics, which were stacked in 3-, 5-, and 7-layers. The super-sensitivity of 2.58 ×103 kPa-1 at low pressure was observed in the 7-layer pressure sensor. The strain sensors were obtained from rGO-coated twisted silk yarns whose gauge factor was 0.307. Although this value is small or comparable to other sensors, it is appropriate for motion sensing. The results of this study show a cost-effective and simple method for the fabrication of pressure and motion sensors with commercial silk and GO.

Milled MgH2, NaAlH4, MgH2–10NaAlH4, MgH2–30NaAlH4, MgH2–50NaAlH4, and MgH2–2Ni-10NaAlH4 samples were prepared by milling in hydrogen atmosphere (reactive mechanical milling, RMM). Decomposition temperatures of milled MgH2, NaAlH4, MgH2–10NaAlH4, and MgH2–30NaAlH4 were examined in a Sieverts-type hydrogen-absorption and release apparatus, in which the hydrogen pressures were kept constant during hydrogen absorption or release. As the content of NaAlH4 in the sample increased, the temperature at the highest peak in the ratio of increase in Hr to increase in T, dHr/dT, versus T curve decreased. The higher content of NaAlH4 is believed to have made effects of reactive mechanical milling stronger. Effects of the NaAlH4 content on the temperatures of intermediate reactions were studied for MgH2 – NaAlH4 composites. Phase formation in the cycled MgH2–50NaAlH4 were investigated. The hydrogen-storage properties of MgH2–30NaAlH4 were compared with those of Mg-based alloys in which oxide, halides, or fluoride was added.

Our study provides guidelines on how to build long-term customer relationship in the non-contract mechanism context. More specifically, the findings show that special, social, and core benefits influence calculative commitment, and operational and special benefits influence affective commitment. This study also supports that calculative and affective commitment play a crucial role in understanding multi-channel agencies’ loyalty. In sum, this study revealed that calculative and affective commitment can be considered as partial or full mediators in the relationship between RBs (relational benefits) and loyalty. This study not only contributed to the existing SET (social exchange theory) and RBs paradigm but also provided practical implications for food distribution management.

Recently, the demand for electric vehicle is increasing worldwide due to eco-friendly policies and stricter emission regulations. As a traction motor for electric vehicle, interior permanent magnet synchronous motors are mainly used. For the design of the interior permanent magnet synchronous motor, the magnetic equivalent circuit method, which is a method of lumped constant circuit, and the finite element method, which is a method of distributed constant circuit, mainly are used. Magnetic equivalent circuit method is useful for simple design through fast and intuitive parameters, but it cannot derive the distribution of magnetic field. The finite element method can derive an accurate magnetic field distribution, but it takes a long time to analyze and it is difficult to analyze intuitive design parameters. In this paper, magnetic equivalent circuit method and Carter coefficient are mixed for rotor structure design. This design method will be called the hybrid magnetic equivalent circuit method. Intuitive design parameters are derived through this hybrid magnetic equivalent circuit method. We will derive the Air gap flux density distribution according to rotor shape, no-load induced voltage, and cogging torque, and compare and verify it with the finite element method.

A surgical microscope is large in size, which makes it impossible to be portable. The distance between the surgical microscope and the observation tissue is 15–30 cm, and the adjustment range of the right and left of the camera is a maximum of 30°. Therefore, the surgical microscope is generated attenuation (above 58%) of irradiation optical source owing to the long working distance. Moreover, the observation of tissue is affected because of dazzling by ambient light as the optical source power is strong (55 to 160 mW/cm2). Further, observation blind spot phenomena will occur due to the limitations in adjusting the right and left of the camera. Therefore, it is difficult to clearly observe the tumor. In this study, a compact pen-type probe with a portable surgical microscope is presented. The proposed surgical microscope comprises a small and portable pen-type probe that can adjust the working distance between the probe and the observed tissue. In addition, it allows the adjustment of the viewing angle and fluorescence brightness. The proposed probe has no blind spots or optical density loss.

A surgical microscope is large in size, making portability impossible. The distance between the surgical microscope and the observation tissue is 15 to 30 cm, while the maximum adjustment range of the camera to the right and left is 30°. Therefore, surgical microscopes cause attenuation (above 58%) of the irradiation optical source owing to the long working distance. Moreover, the observation of tissue was dazzled with ambient light because the optical power source was strong (50 to 160 mW/cm2). Owing to the limited ability to adjust the camera to the right and left, a blind spot occurs with a surgical microscope. Therefore, it is difficult to clearly observe a tumor. In this study, a compact pen-type probe with a portable surgical microscope is proposed. The pen-type probe is small with a portable shape, and is capable of adjusting the working distance between itself and the observed tissue. It is also possible to adjust the viewing angle and fluorescence brightness. The proposed pen-type probe has no blind spots or optical density loss.

A metering roundabout where traffic is controlled by traffic lights with phase times influenced by queue detector occupancy might be the solution to enhance performance when there are unbalanced traffic flows at roundabouts. There have, however, been minimal studies on how the distance of the queue detector from the stop line affects signal phase time durations and the queuing lengths. This research, therefore, seeks to develop a Cuckoo Search/Local search Algorithm using parameters such as arrival volumes, conflicting volumes, detector distance and phase time to investigate the relationship of signal setting, detector location and queuing formulations. Also, some additional statistical tests were performed for the fitness of the data. In order to conduct solid model validations, model output data was compared against the AIMSUN model. The results from the analyses demonstrated that the queue detector distance can affect phase time durations and vehicle queuing lengths on the controlling approach as well as queuing lengths on the metered approach. This study showed that, based on the study for the Old Belair Road roundabout in Adelaide, South Australia, the total queue length (controlling + metered) will be minimized when the detector is relocated at 209 meters from the roundabout stop line, giving longer phase green times and resulting in decreased intersection queuing lengths.

The irradiation biology of the brown marmorated stink bug (BMSB, Halyomorpha halys Stål) treated at the nymphal stage was investigated to determine its application for sterile insect technique (SIT). Fifth instar males of BMSB were exposed to gamma-radiation 60Co at different doses of 12, 16, 20, 24 and 64 Gy. Irradiated males were mated with non-irradiated virgin females to assess the longevity of both sexes, female fecundity and fertility of their offspring until the egg stage of the F2 generation. The mortality of each of the developmental stages of the F1 and eggs of the F2 generation was observed to determine whether negative effects from exposure to radiation was inherited. The data indicated that irradiation significantly reduced the lifespan of male insects at doses above 20Gy. Irradiated males did not affect the longevity and fecundity of their female partners, nor either sex of their resulting progeny, but it did reduce the hatch rate of the eggs at all doses tested. The sterility rates of F1 eggs were 55.6%, 73.3%, 74.1% and 74.1% at doses of 12Gy, 16Gy, 20Gy and 24Gy respectively. Eggs were completely sterile (100%) at a dose of 64Gy with no egg hatch recorded. A low hatch rate of F2 eggs illustrated that negative effects from radiation was inherited by the subsequent generation. The results support the potential for the use of SIT for BMSB management by irradiating the fifth instar male nymphs at 16-64Gy.

In this paper, the design process of BLDC adopting the dual rotor method that can reduce the overall size of the motor while generating the same torque as the conventional Permanent Magnet BLDC is analyzed. A simple size is selected by obtaining the torque per rotor volume (TRV), and a method of matching the counter electromotive force by selecting the pole arc of the magnet through a magnetic equivalent circuit is analyzed. Since the efficiency is low because the 120-degree commutation method is selected, the middle stator is optimized through detailed design through the experimental design method. Afterwards, it has the advantage of being able to shift without stopping due to the characteristic of a dual rotor. For this, an analysis of the driving characteristics for each mode is performed.

This study investigated clinical nurses’ knowledge and visual differentiation ability of the pressure injury classification system (PICS) and incontinence-associated dermatitis (IAD), additionally analyzing possible influencing factors. A convenience sample of 248 nurses took the PICS and IAD knowledge test (KT) and completed the visual differentiation ability test (VDAT), consisting of 21 photographs with clinical information. The overall mean score for correct answers was 12.65±2.90 points in PICS & IAD KT and 11.43±4.57 points in VDAT. Incorrect responses were most common for statements related to stage Ⅱ, Ⅲ, IAD for PICS & IAD KT, and deep tissue pressure injury (DTPI), unstageable, and stage Ⅲ for VDAT. Significant correlations were found between PICS & IAD KT and VDAT (r=.252, p<.001). Factors affecting scores for VDAT were the scores of PICS & IAD KT, debridement experience in nursing patients with PI, and the management frequency of PI and IAD. Results indicate that nurses have an overall understanding of PICS and IAD, but low visual differentiation ability regarding stage Ⅲ, DTPI, and unstageable PI. Continuing education is needed to further improve knowledge and visual differentiation ability for PICS and IAD.

Currently, maritime traffic is increasing with economic growth in several regions worldwide. However, this growth in maritime traffic has led to increased risk of marine accidents. These accidents have a higher probability of occurring in regions where geographical features, such as islands, are present. Further, the positioning of rescue ships in a particular ocean region with a high level of maritime activity is critical for rescue operations. This paper proposes a method for determining an optimal set of locations for stationing rescue ships in an ocean region with numerous accident sites in the Wando islands of South Korea. The computational challenge in this problem is identified as the positioning of numerous islands of varying sizes located in the region. Thus, the proposed method combines a clustering-based optimization method and an image processing approach that incorporates flood filling to calculate the shortest distance between two points in the ocean that detours around the islands. Experimental results indicate that the proposed method reduces the distance from rescue ships and each accident site by 5.0 km compared to the original rescue ship locations. Thus, rescue time is reduced.

This paper discusses a significant public-private partnership (PPP) formed by the government and Taiwanese Farmer Associations. Particularly, it will investigate a pattern of the PPP that has successfully promoted rural development and agricultural modernization in Taiwan since 1950s. Taiwanese Farmer Associations (hereafter TFAs), similar to agricultural cooperatives in South Korea and Japan, have played a policy agent in fostering rural development in this island state since 1950s. TFA’s performance inherently came from Japanese Cooperatives before World War II. The Performances of those farmer organizations are combinations of economic, social, and educational synergies. The rural development experiences in Taiwan demonstrate that success of rural modernization is carried out by a special public-private partnership (PPP). First, this paper discusses formation and development of farmer cooperative organizations in East Asian societies and compare the similarities and differences of practice of those organizations and their relations to the governments among Taiwan, South Korea, and Japan. Secondly, this paper examines collaborative mold and process in which both the government and Taiwan Farmer Associations have been extensively involved. A specific cooperative apparatus between the government and TFA functioning and operating as a perfect PPP has been formed under administrative guidance of the state. Thirdly, this paper looks at input and various supports in financial and policy perspective by the public sector. Fourthly, the paper discusses legal framework, administrative apparatus, and governance pattern for TFA. Fifthly, the paper discuses that a specific PPP successfully involving in rural modernization in Taiwan is significantly derived from the state’ guidance that properly regulates a collaboration between the government and TFA. So-call East Asian model of PPP in agricultural modernization and rural community development may become a valuable experience for most of developing countries.

Background and objectives: TSC1 is a crucial component of the mTOR pathway, impacting cell growth, proliferation, and autophagy, while TSC2 is a tumor suppressor gene that regulates cell growth and is associated with the mTOR signaling pathway. In the present study, we analyzed TSC1 and TSC2 mRNA expression levels in rectal cancer, and evaluated the clinicopathological and prognostic characteristics of TSC1 and TSC2. Materials and Methods: TSC1 and TSC2 mRNA expression was examined in various cancer types. We further evaluated survival to determine the prognostic significance of TSC1 and TSC2 mRNA in CRC using The Cancer Genome Atlas (TCGA) data. Results: The study focused on rectal cancer, as it exhibited the most promising results. The patients were split into two subgroups, each comprising 50% of the total, based on the TSC gene expression levels. This division was made to assess the clinical characteristics associated with the expression of TSC1 and TSC2 genes. In the study, lower TSC1 expression was linked to venous invasion in rectal cancer patients, and there was also a related trend with lymphatic invasion, although it didn't reach statistical significance. Lower TSC2 expression was observed in younger patients and had some associations with sex and M stage, but these correlations were not statistically significant. When it came to survival analysis, TSC1 expression did not significantly impact overall survival, while higher TSC2 expression was associated with a poorer prognosis in rectal cancer. To enhance our comprehension, additional research, especially in larger case studies, is needed to explore the molecular mechanisms and clinical characteristics of TSC genes in colorectal cancer.

Abstract: Global ecological concern regarding the transfer of fouling organisms to ship hulls is increasing. This study investigated the species composition, dominant species, distribution patterns, community structure, and life-cycle differences of hull-fouling macroinvertebrates on five research vessels (R/Vs: Isabu, Onnuri, Eardo, Jangmok 1, and Jangmok 2) operated by the Korea Institute of Ocean Science and Technology (KIOST). Hull-fouling macroinvertebrates were collected three to five times on quadrats from the upper and middle sectors of the hull sides, bottom, and niche areas (the propellers and shafts and the thrusters). A total of 47 macroinvertebrate species were identified, represented by 8,519 individuals(ind.)/m2 and a biomass of 1,967 gWWt/m2 on the five vessels. The number of species, density, and biomass were greater on the coastal vessels the Eardo, Jangmok 1, and Jangmok 2 than on the ocean-going vessels the Isabu and Onnuri. Among the coastal vessels, barnacles were the most abundant and had the greatest density, while mollusks had the highest biomass. Differences between hull sectors showed that the highest species abundance and density appeared on all hulls in ports and bays where the Jangmok 1 operated, while the highest species abundance, density, and biomass were identified in the niche areas of the Eardo, which operated farther from the coast. The hull-fouling macroinvertebrates that exceeded 1% of all organisms were the barnacles Amphibalanus amphitrite, Balanus trigonus, and Amphibalanus improvisus; the polychaete Hydroides ezoensis; the bivalves Magallana gigas and Mytilus galloprovincialis; and the amphipod Jassa slatteryi. The dominant species were cosmopolitan and globally distributed, and many of them were cryptogenic. Six native species were identified: M. gigas, H. ezoensis, the amphipod Melita koreana, the isopod Cirolana ko-reana, and the barnacle B. trigonus and F. kondakovi. Eight non-indigenous species (NIS) were de-tected: barnacles A. amphitrite and A. improvisus, the bivalve M. galloprovincialis, the polychaete Perinereis nuntia, amphipods J. slatteryi and Caprella californica, and bryozoans Bugulina californica and Bugula neritina. Of the fouling macroinvertebrates found on the vessel hulls, 13% were native and 17% were NIS. The nMDS ordination analysis of the five vessels showed four clusters of fouling macroinvertebrate communities: two ocean clusters (the Isabu and Onnuri), one coastal cluster (the Eardo and Jangmok 2), and one local cluster (the Jangmok 1). More diverse communities developed on the hulls of vessels that operated locally rather than globally or in deep oceans. Spearman rank correlation showed that biological indices such as number of species, density, and biomass correlated highly and positively with the numbers of days on coastal operations and negatively with the number days on ocean operations. The species diversity index correlated positively with the total number of anchoring days and coastal operation days and negatively with the total number of operation days and ocean operation days. The macroinvertebrates differed by the area of operation, the port of anchorage, the number of days in operation and at anchor, and the hull sectors. There is no previous research data on hull-fouling macroinvertebrates in the Republic of Korea, and this study provides a basis for future studies to identify introduced species and their differences based on operation area.

This paper presents an approach to improve the robustness of tip-tilt controllers for fast-steering mirror (FSM)-based laser beam steering (LBS) systems in the presence of dynamic disturbances such as external shocks. To this end, we propose the addition of a disturbance observer (DOB)-based anti-shock controller in parallel to the original linear servo control loop to improve its control performance in the presence of external shocks. To increase the tip-tilt control performance against external shocks, the DOB-based control method, which is an improved control method for eliminating nonperiodic disturbances, is implemented in the original tip-tilt control system. Results indicate that the control error of the DOB-based anti-shock controller decreased, resulting in an efficient improvement in its disturbance-rejection performance.

This study presents an effective control algorithm to improve the robustness of fast steering mirror (FSM)-based laser beam steering systems against dynamic disturbances such as repetitive disturbances resulting from operating conditions. A stable control system must be able to maintain the required high-precision control even when dynamic disturbances affect the FSM system. In this study, an improved control method is proposed using an internal model principle (IMP)-based nonlinear controller with a disturbance observer (DOB) for the FSM system. This IMP-based controller with DOB can attenuate the residual control error signal under dynamic disturbance conditions.

Past epigenetic information refers to the epigenetic modifications that have occurred in the past have since been updated. These modifications may no longer be present and not actively influencing on cellular functions. When past epigenetic modifications disappear, the precise records of those modifications typically may be vanish. If it is indeed true, a critical question arises: Can an organism sustain continuous survival and evolution without the information about past epigenetic modifications up to the present? It is reasonable to assume that among the information about past modifications, there could be crucial data essential for survival and evolution. If all these experiences were to vanish, rendering them unknowable in the present, it would undoubtedly pose significant challenges to survival and evolution. Therefore, the argument that such epigenetic information has been securely stored somewhere within the cell is not merely speculative but likely a factual reality.In this study, a new term “Epigenetic Archive”, is introduced in biology. It refers to a data repository that encompasses all experience data on past epigenetic modifications. The argument presented here underscores the importance of Epigenetic Archive and the need for its secure preservation. According to the argument, the information that cells experience should be continuously and securely stored, and any distortion of this information is said to be inconsistent with the principles of evolution and survival. This information is seen as evidence of a cell's successful existence up to the present, and it is emphasized that this successful record must be preserved. From this perspective, Epigenetic Archive should be designed to safely store past biological experiences and link this information securely to the present data. This study proposes that the data architecture in Epigenetic Archive is indeed akin to the principles of blockchain technology, particularly in terms of immutability and a distributed ledger securely preserving information across generations and ensuring that all cells possess consistent epigenetic information across a biological organism.The applications and implications of such an analogy of blockchain to Epigenetics could be an original contribution for future research on biology and genetics.

We evaluated the transcriptional response of interferon (IFN)-related genes in rock bream iridovirus (RBIV)-infected rock bream under high-, low-, or no-mortality conditions induced by different stocking water temperatures. Under the high susceptibility condition (group A, water temperature 26 °C, 100% mortality), only the Mx gene was expressed early, with prolonged expression, and with heavy viral loads of approximately 106–107 major capsid protein gene copies/μL from 4 to 10 days post infection (dpi). However, IRF1, IRF3, IRF8, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56 were activated at later time points (8 dpi) and then quickly decreased (10 dpi). For the low susceptibility condition, the water temperature was set at 23 °C for 7 days (group B) and then reduced to 17 °C. Group B exhibited a 28% mortality rate, in which persistent and effective antiviral responses were observed for long periods of time. In particular, at 20 and 22 dpi, when virus replication was peaked at approximately 107/μL, the expressions of most of the IFN-related genes (IRF1, IRF3, IRF8, Mx, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56) were significantly higher in group B than in the control group. Moreover, prolonged and higher levels of IRF3 (at least 30 dpi), IRF8 (at least 30 dpi), ISG15 (at least 30 dpi), PKR (at least 28 dpi), Viperin (at least 30 dpi), and IFI44 (at least 30 dpi) were also observed in the recovery stage of infection. Under the no-susceptibility condition at 17 °C (0% mortality), significantly elevated levels of IRF3, Mx, ISG15, and PKR were observed mostly until 20 dpi. The findings indicate that RBIV infection can induce an efficient IFN-mediated antiviral immune response in low- and no-susceptibility conditions. The findings could be valuable for effective control of viral pathogens in fish.

At 100% penetration, intermittent renewable energy causes outages. To flatten the leaping supply and demand curves of renewable energy, an energy storage medium and carrier are required. The Hydrogen energy stotrage system (HydESS), which combines a proton exchange membrane (PEM)-based water electrolysis (WE) system and a fuel cell (FC), has the quickest response time, the longest duration, and the greatest storage capacity. HOMER tools for techno-economic analysis are used to evaluate the HydESS hybrid system. Kyiv, Ukraine, is appealing due to its spatial-temporal wind speed, solar irradiance, and energy security. With an LCOE of $0.245 kWh−1 and 9.3% fuel cell power output, the most feasible solution is onshore wind turbine-coupled PEMFC HydESS. As a result 1,000-kW wind power, 250-kW PEMFC, 250-kW PEMWE, and 441-kW BESS are optimized to serve a 3,900 kWh day academic residence load. When compared to a diesel generator and a BESS, the hybrid HydESS reduces CO2 emissions by 4,132 tons over a 25-year period. The LCOE of a hybrid HydESS system is determined by the SOFC lifetime rather than the PEMFC's 2% difference between 40,000 and 50,000 h with the same rated power. This study recommends accelerating PEMFC development with fluctuation-endurable materials and design.

This study emphasizes the necessity of introducing a blockchain-based joint logistics system to strengthen the competency of medical supply chain management (SCM) and tries to develop a healthcare supply chain management (HSCM) competency measurement item through an analytic hierarchy process. The variables needed for using blockchain-based joint logistics are the performance expectations, effort expectations, promotion conditions, and social impact of the UTAUT model, and the HSCM competency results in increased reliability and transparency, enhanced SCM, and enhanced scalability. Word cloud results, analyzing the most important considerations to realize work efficiency among medical industry-related agencies, mentioned numerous words, including sudden situations, delivery, technology trust, information sharing, effectiveness, urgency, etc. This might imply the need to establish a system that can respond immediately to emergency situations during holidays. It could also suggest the importance of real-time information sharing to increase the efficiency of inventory management. Therefore, there is a need of a business model that can increase the visibility of real-time medical SCM through big data analysis. By analyzing the importance of securing reliability based on the blockchain technology in the establishment of a supply chain network for HSCM competency, we reveal that joint logistics can be achieved and synergistic effects can be created by implementing the integrated database to secure HSCM competency. Strengthening partnerships, such as joint logistics, will eventually lead to HSCM competency. In particular, HSCM should seek ways to upgrade its competitive capabilities through big data analysis based on the establishment of a joint logistics system.

The study presents a mathematical modeling for supporting the premise that our body is composed of blockchain systems. A cell population is considered a space with peer-to-peer communication networks for applying blockchain protocol. Transaction is defined as gene expression that constantly occurs for protein synthesis in each cell. The transaction process proceeds according to the blockchain protocol with sharing and recording the data on the blockchain ledger. The premise comes from the clues of the previous research such that the cell population is a complex structured network system having cell-to-cell connections. Although individual cells exhibit stochastic nonlinear dynamic behavior, cell population shows consensus behavior that reaches to ensemble through interaction among cells. It is inferred that gene expression is not regulated by the corresponding cell only nor determined by external intelligence such as the brain. This is achieved through a consensus through stochastic interactions between cells over the whole cell population. These findings imply that mathematical blockchain modeling is a suitable for gene expression process. The original contribution of the study is a methodology for applying mathematically the blockchain protocol to the real biological gene expression process. In other words, the DNA sequence is converted into a numeral bit sequence that makes it possible to implement the blockchain protocol. A new DNA sequence scheme is proposed with adding methylated cytosine and adenine as the 5th and 6th bases for including epigenetic information which has profound effect on gene expression and regulation. The methodology was applied to the real biological synthesis process of protein samples. The protein is composed of amino acids that are encoded by triplet codons of 216 kinds with 6 base RNA sequence. The gene expression information is traced backward from a synthesized protein sample, amino acids of codons, RNA transcript up to DNA sequence. One of the results is a numeric value in the form of a bit sequence with which mathematical blockchain modeling is applicable. The cryptographic authentication and the consensus process are mathematically proven to work properly by the blockchain protocol. It implies that the same protein is synthesized, but with different epigenetic data, then protein's latent material properties will certainly be different. Although the result has not been justified by the biologic experiment yet, it is sure that the biological hidden algorithm inside DNA sequence will be revealed by the binary bit-logic with physical on/off states which is mathematically proven. The research will greatly contribute to disease treatment and medicine development as well as epigenetics in the future.

This paper develops Bayesian inference in reliability of a class of scale mixtures of log-normal failure time (SMLNFT) models with stochastic (or uncertain) constraint in their reliability measures. The class is comprehensive and includes existing failure time (FT) models (such as log-normal, log-Cauchy, and log-logistic FT models) as well as new models that are robust in terms of heavy-tailed FT observations. Since classical frequency approaches to reliability analysis based on the SMLNFT model with stochastic constraint are intractable, the Bayesian method is pursued utilizing a Markov chain Monte Carlo (MCMC) sampling based approach. This paper introduces a two-stage maximum entropy (MaxEnt) prior, which elicits a priori uncertain constraint and develops Bayesian hierarchical SMLNFT model by using the prior. The paper also proposes an MCMC method for Bayesian inference in the SMLNFT model reliability and calls attention to properties of the MaxEnt prior that are useful for method development. Finally, two data sets are used to illustrate how the proposed methodology works.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

Gesture recognition technology has been quickly developed in the field of human-computer interaction. The multiple-input multiple-output (MIMO) radar has been widely adopted in gesture recognition because of its notable spatial resolution. In this work, a highly accurate MIMO radar-based hand gesture recognition algorithm with very low complexity is proposed. To make the proposed system applicable in the industry and work well even when the size of the training data is limited, we applied several low-complexity adaptive signal processing methods to extract features and reduce the noise effect. First, spectrum analysis is applied to range-Doppler maps (RDMs) and a cell-averaging constant false alarm rate (CA-CFAR) with mirror filters is applied to improve the robustness to noise. Afterward, the features related to the distance, speed, direction, and the elevation angle of the moving object are determined by the proposed adaptive signal analysis techniques and the random forest is applied for classification. The proposed system has the capability to precisely distinguish and identify eight motions, including waving, moving to the left or right, patting, pushing, pulling, and rotating clockwise or anticlockwise, with an accuracy of 95%. Experiments demonstrate the capability of the proposed hand gesture recognition system to classify different movements precisely.

Aging is associated with muscle atrophy and fatty infiltration of skeletal muscle. The multifidus muscle stabilizes the lumbar spine and undergoes adipose accumulation with age, leading to functional decline in the elderly. Therefore, quantitative assessment of the multifidus muscle can be beneficial for the elderly when formulating treatment strategies and reducing future complications. Fifty-seven patients (mean age, 73.89 ± 6.09; 23 male patients) who underwent lumbar Magnetic resonance imaging (MRI) were prospectively recruited. The cross-sectional area (CSA) of the multifidus from the L2-S1 level and the CSA of the L4-5 level psoas muscle were measured. The functional CSA (fCSA) of the multifidus muscle was measured by excluding the fat infiltration area from the multifidus CSA. The CSA to fCSA ratio was obtained by multiplying 100 by the value obtained by dividing CSA by the fCSA. Pfrrmann classification was used to evaluate the degree of disc degeneration. The functional disability measurements were the Short Physical Performance Battery (SPPB), Berg Balance Scale (BBS), grip strength, and functional reach test (FRT). Pearson's correlation analysis was used to examine the relationship between the functional disability measurements and the multifidus muscle. The CSA to fCSA ratio value was relatively constant at each spine level and showed a significant correlation with the SPPB, grip strength, FRT, and psoas index (p&lt;0.05). However, degree of disc and multifidus muscle degeneration were not statistically significant. So, age-related changes play a significant role in developing back muscle fatty infiltration than disc dgeneration. Moreover, Grip strength showed a stronger relationship with the quality of the multifidus muscle than other functional disability measurements.

Rice cultivation serves as a significant anthropogenic source of methane (CH4), a primary greenhouse gas, and nitrous oxide (N2O), a secondary greenhouse gas. Although N2O emissions remain relatively small compared to CH4 emissions, they are remarkably affected by nitrogen-fertilized soil conditions during rice cultivation. To date, investigations are very limited concerning N2O emissions from rice cultivation in relation to environmental factors such as temperature, rainfall, and soil properties. In this case study, we investigated the characteristics of N2O emissions in the central region of South Korea, where a single rice cropping cycle occurs annually over a span of three years, from May 2020 to May 2023. We investigated the impact of variations in temperature and soil moisture on N2O emissions during rice cultivation. In this context, we attempted to discover the complex dynamics of N2O emissions by comparing longer fallow periods with the rice cultivation periods and extended non-dry periods with irrigated periods. We observed that extremely high N₂O flux events encountered during the fallow period appeared to have a substantial impact on the yearly cumulative N₂O emissions, surpassing the impact of cumulative N₂O emissions during the rice cultivation period. We found that high N₂O flux events arose not only from artificial nitrogen inputs but also due to temperature and soil moisture variations influenced by weather conditions. We concluded that assessing N₂O emissions solely based on the rice cultivation period would underestimate annual emissions. To prevent underestimation of N₂O emissions, continual gas collection throughout a year covering both rice cultivation and fallow phases is required in align with monitoring of varying temperature and soil moisture conditions. Based on our findings, we recommend that at least a three whole year evaluation period is needed to ensure estimation accuracy of N₂O emissions under varying nitrogen fertilization rates. Also, the findings from this study would help prepare a further revision or refinement of N2O emission factor from rice cultivation in the national greenhouse gas inventories defined by the inter-governmental panel on climate change (IPCC).

Recently, two respiratory syncytial virus (RSV) vaccines based on the prefusion F (pre-F) antigen were approved in the United States. We developed and validated an enzyme-linked immunosorbent assay (ELISA)-based protocol for the practical and large-scale evaluation of RSV vaccines. Two modified pre-F proteins (DS-Cav1 and SC-TM) were produced by genetic recombination and replication using an adenoviral vector. The protocol was established by optimizing the concentrations of the coating antigen (pre-F proteins), secondary antibodies, and choice of blocking buffer. To validate the protocol, we examined its accuracy, precision, and specificity using serum samples from 150 participants across various age groups and the standard serum provided by the National Institute of Health. In the linear correlation analysis, coating concentrations of 5 and 2.5 μg/mL of DS-Cav1 and SC-TM, respectively, showed high coefficients of determination (r2 = 0.90). Concentrations of secondary antibodies (alkaline phosphatase-conjugated anti-human immunoglobulin G, diluted 1:2000) and blocking reagents (5% skim milk/PBS-T) were optimized to minimize non-specific reactions. High accuracy was observed for DS-Cav1 (r2 = 0.90) and SC-TM (r2 = 0.86). Further, both antigens showed high precision (coefficient of variation &lt; 15%). Inhibition ELISA revealed cross-reactivity of antibodies against DS-Cav1 and SC-TM but not with the attachment protein.

This study aimed to assess the differences in the importance and performance of health awareness in Korean middle school students according to the types of online physical education classes they attended during the coronavirus disease-2019 pandemic. Overall, 583 participants were selected using a convenience sampling method; the data were obtained through an online survey using Google forms. Frequency analysis, reliability analysis, independent sample t-test, and importance-performance analysis were performed. First, the differences between importance and performance were found to be the most for sleep and physical activity management, and the least for disease and hygiene management. In addition, both the groups demonstrated higher importance and performance for hygiene and disease management. There were significant differences in the importance and performance of all the sub-factors. Second, hygiene, disease management, and mental health management were found in quadrant I in both the groups, while physical activity, sleep, and dietary habit management were in quadrant III. No factors were in quadrant II and IV.

The development of technology that combines supercapacitors and lithium-ion batteries by externally connecting them in parallel is ongoing. This study examines the correlation between the volume ratio and electrical characteristics of a cell made by internally connecting a battery capacitor with Li4Ti5O12 as the anode active material and a supercapacitor in parallel. It was found that increasing the volume occupied by the battery capacitor in the cell led to increased cell energy and resistance, resulting in decreased output characteristics. Conversely, increasing the volume occupied by the supercapacitor in the cell led to a decrease in the IR drop during discharge and cell temperature when evaluating cycle characteristics with a current of 20C. The study also examined the behavior of the current distributed during the charging and discharging process based on the volume ratio of the supercapacitor and the battery capacitor. Analyzing the correlation between the volume ratio and electrical characteristics of supercapacitors and battery capacitors could potentially lead to the development of a new type of energy storage device.

According to Hofstede’s theory of cultural dimensions, cultures differ in cultural values and norms; values and norms that may influence differences in trendsetting, creative traits and behaviors, and pro-environmental behaviors. Further, because men and women have been socialized within particular cultures, gender differences may exist in trendsetting, creative traits and behaviors, and pro-environmental behaviors. Trendsetters have characteristics that are interrelated with creative traits and behaviors, perhaps inclining them to endorse pro-environmental behaviors. However, the interrelationships among these variables remain unexplored. Thus, the purpose of this study was to examine these three variables among college students in South Korea and the United States, specifically looking at cultural and gender differences. Participants were 225 Korean college students and 221 U.S. college students. Questionnaires included demographic items and scales measuring trendsetting, creative traits and behaviors, and pro-environmental behaviors. Data analyses included descriptive statistics, Cronbach’s alpha reliability, MANOVA, ANOVA and SNK posthoc test. Results show that U.S. (vs Korean) students indicated greater trendsetting and creative traits and behaviors but not greater pro-environmental behaviors. Fashion trendsetting groups in both Korea and the U.S. differed in creative traits and behaviors and pro-environmental behaviors. Among Korean trendsetting groups, reluctant adopters scored lowest on creative traits and behaviors and pro-environmental behaviors. Among U.S. trendsetting groups, trendsetters scored highest on creative traits and behaviors and pro-environmental behaviors; reluctant adopters scored lowest on pro-environmental behaviors. Theoretical and practical implications are provided for researchers and marketers.

Railway has been used as one of the most crucial means of transportation in public mobility and economic development. For efficiently operating railways, the electrification system in railway infrastructure, which supplies electric power to trains, is essential facilities for stable train operation. Due to its important role, the electrification system needs to be rigorously and regularly inspected and managed. This paper presents a supervised learning method to classify Mobile Laser Scanning (MLS) data into ten target classes representing overhead wires, movable brackets and poles, which are recognized key objects in the electrification system. In general, the layout of railway electrification system shows a strong regularity of spatial relations among object classes. The proposed classifier is developed based on Conditional Random Field (CRF), which characterizes not only labeling homogeneity at short range, but also the layout compatibility between different object classes at long range in the probabilistic graphical model. This multi-range CRF model consists of a unary term and three pairwise contextual terms. In order to gain computational efficiency, MLS point clouds is converted into a set of line segments where the labeling process is applied. Support Vector Machine (SVM) is used as a local classifier considering only node features for producing the unary potentials of CRF model. As the short-range pairwise contextual term, Potts model is applied to enforce a local smoothness in short-range graph. While, long-range pairwise potentials are designed to enhance spatial regularities of both horizontal and vertical layouts among railway objects. We formulate two long-range pairwise potentials as the log posterior probability obtained by Naïve Bayes classifier. The directional layout compatibilities are characterized in probability look-up tables which represent co-occurrence rate of spatial relations in horizontal and vertical directions. The likelihood function is formulated by multivariate Gaussian distributions. In the proposed multi-range CRF model, the weight parameters to balance four sub-terms are estimated by applying the Stochastic Gradient Descent (SGD). The results show that the proposed multi-range CRF can effectively classify detailed railway elements, representing the average recall of 97.66% and the average precision of 97.07% for all classes.

A number of accidents at sea are primarily caused by low visibility due to sea fog therefore, it is important to estimate sea fog intensity and visibility in real-time in the ocean environment. However, the existing estimation systems have significant costs so that it is not viable to install them at various locations, such as small vessels, minor ports, and a number of buoys. Therefore, this paper proposes an algorithm called RDCP (Reduced Dark Channel Prior) which provides the estimation at a low complexity and a low cost. For the estimation, the RDCP algorithm firstly acquires dark channels from an ocean image, then applies an optimized threshold value to the dark channels, and crops out the sky region in the ocean image. For the estimation performance evaluation, 320 raw images captured from cameras at four different ports in South Korea are used rather than artificially composed images. Considering facilities in oceans which are usually operated in the power limited environment, the processing time performance of PDCP are also examined. The experiments demonstrate that the RDCP algorithm provides reliable estimation performance in real-time.

Background The Delta Neutrophil Index (DNI), a prodiagnostic marker for sepsis, utilizes leukocyte count. Platelet activation, similar to leukocytes, plays a crucial role in host defence against pathogens and may serve as a predictor of sepsis outcome. However, the combined evaluation of Mean Platelet Component (MPC) and DNI in assessing sepsis has been rarely used. Methods To assess the prodiagnostic validity of simultaneous utilization of DNI and MPC in cases of human febrile sepsis, we conducted measurements of cellular indices, including DNI and MPC, as well as molecular biomarkers such as procalcitonin (PCT) and C-reactive protein (CRP). This study was carried out on patients admitted to the emergency department with suspected sepsis. Results Using a cutoff value of 2.65%, the sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) of DNI in sepsis were found to be 69%, 73.9%, 77.9%, and 64.1%, respectively. Furthermore, significant differences in DNI and MPC levels were observed between the sepsis and non-sepsis groups (6.7±7.8% versus 2.1±2.2%, P=0.000 and 26.0±1.9 g/dl versus 26.8±1.4 g/dl, P=0.002), respectively. Notably, there was a negative correlation between DNI and MPC, with the strength of the correlation varying based on the cause of sepsis. By setting the cutoff value for DNI at 6.2%, the sensitivity, specificity, and NPV improved to 100%, 80.3%, and 100%, respectively, although the PPV remained at 10.6%. Importantly, the DNI≥6.2 group exhibited a higher incidence of death (10.9%, 5/46) and multiorgan failure (19.6%, 9/46) compared to the DNI<6.2 group (0.0%, 0/46 and 0.0%, 0/167, respectively) (P=0.000 and P=0.000, respectively). Conclusions In our study, DNI demonstrates superior effectiveness compared to other molecular biomarkers such as CRP and procalcitonin in distinguishing febrile septic patients from febrile nonseptic patients and predicting prognosis. Additionally, there exists a negative correlation between MPC and DNI, making MPC a valuable marker for differentiating the etiology of sepsis. These findings hold significant clinical implications as DNI/MPC is a cost-effective and readily applicable approach in various impending sepsis scenarios. Notably, this study represents the first examination of the prodiagnostic validity of simultaneously employing DNI and MPC in human cases of febrile sepsis.

Though Moracin D derived from Morus alba was known to have anti-inflammatory and antioxidant activities, the underlying antitumor mechanism of Moracin D was never unveiled so far. Thus, in the recent study, the apoptotic mechanism of Moracin D was elucidated in breast cancer cells. Herein, Moracin D exerted significant cytotoxicity in MDA-MB231 and MCF7 cells. Also, Moracin D increased sub G1 population, cleaved poly (ADP-ribose) polymerase (PARP) and attenuated the expression of pro-cysteine aspartyl-specific protease (procaspase 3), c-Myc, cyclin D1, B-cell lymphoma 2 (Bcl-2),and X-linked inhibitor of apoptosis protein (XIAP) in MDA-MB231 cells. Of note, Moracin D reduced expression of Forkhead box M1 (FOXM1), β-catenin, Wnt3a, and upregulated glycogen synthase kinase 3 beta (GSK 3β) on Tyr216 along with disturbed binding of FOXM1 with β-catenin in MDA-MB-231 cells. Conversely, GSK3β inhibitor SB216763 reversed the apoptotic ability of Moracin D to reduce expression of FOXM1, β-catenin, pro-caspase3 and pro-PARP in MDA-MB-231 cells. Overall, these findings provide novel insight that Moracin D inhibits proliferation and induces apoptosis via suppression of Wnt3a/FOXM1/β-catenin signaling and activation of caspase and GSK3β

The interest in renewable energy to replace fossil fuel is increasing as the problem caused by climate change become more severe. Small hydropower (SHP) is evaluated as a resource with high development value because of its high energy density compared to other renewable energy sources. SHP may be an attractive and sustainable power generation environmental perspective because of its potential to be found in small rivers and streams. The power generation potential could be estimated based on the discharge in the river basin. Since the river discharge depends on the climate conditions, the hydropower generation potential changes sensitively according to climate variability. Therefore, it is necessary to analyze the SHP potential in consideration of future climate change. In this study, the future prospect of SHP potential is simulated for the period of 2021 to 2100 considering the climate change in three hydropower plants of Deoksong, Hanseok, and Socheon stations, Korea. As the results, SHP potential for the near future (2021 to 2040) shows a tendency to be increased and the highest increase is 23.4% at the Deoksong SPH plant. Through the result of future prospect, we have shown that hydroelectric power generation capacity or SHP potential will be increased in the future. Therefore, we believe that it is necessary to revitalize the development of SHP in order to expand the use of renewable energy. Also, a methodology presented in this study could be used for the future prospect of the small hydropower potential.

It has been more than three decades since the discovery of multifunctional factors, Non-POU Domain-Containing Octamer-Binding Protein, NonO and Splicing Factor, Proline-and Glutamine-Rich, SFPQ. Some of their functions, including their participations in transcriptional and posttranscriptional regulation as well as their contribution to paraspeckle subnuclear body organization have been well-documented. In this review, we focus on the roles of NonO and SFPQ in cell cycle with particular attention to their participation in nonhomologous end joining (NHEJ) and homologous recombination (HR) of DNA damage responses induced by irradiation. In these contexts, absence or malfunction of either or both lead to genome instability and ultimately to apoptosis, cellular senescence, and tumor development. This review also will shed light on NonO and SFPQ function in DNA/RNA/protein binding and their association with Ku heterodimer of the NHEJ pathway required for repair of DNA double-strand breaks (DSBs).

This study reports the preparation of silica and nano-fructosome encapsulated Candida antarctica lipase B particles (CalB@NF@SiO2) and demonstration of their enzymatic hydrolysis and acylation. CalB@NF@SiO2 particles were prepared as a function of TEOS concentration (3-100 mM). Their mean particle size was 185 nm by TEM. Enzymatic hydrolysis was performed to compare catalytic efficiencies of CalB@NF and CalB@NF@SiO2. Catalytic constants (Km, Vmax, and Kcat) of CalB@NF and CalB@NF@SiO2 were calculated with Michaelis-Menten equation and Line-weaver Burk plot. Optimal stability of CalB@NF@SiO2 was found at pH 8 and temperature of 35 ℃. Moreover, CalB@NF@SiO2 particles were reused for seven cycles to evaluate their reusability. In addition, enzymatic synthesis of benzyl benzoate was demonstrated by an acylation reaction with benzoic anhydride. The efficiency of CalB@NF@SiO2 for converting benzoic anhydride to benzyl benzoate by the acylation reaction was 97%, indicating that benzoic anhydride was almost completely converted to benzyl benzoate. Consequently, CalB@NF@SiO2 particles are better than CalB@NF particles for enzymatic synthesis. In addition, they are reusable with high stability at optimal pH and temperature.

The objective of the present paper is to get a better understanding of the electrochemical properties of organoclays, which were prepared via solid-state intercalation of three cationic surfactants, such as dodecyltrimethylammonium, tetradecyltrimethylammonium, and hexadecyltrimethylammonium, as bromide salts, at different loading levels into the interlayers of two natural smectite clays (AH and DI). The electrochemical properties of the prepared organoclays were investigated by cyclic voltammetry. The cyclic voltammetry response of the electrochemical probe, 〖Fe(CN)〗_6^(3-)/〖Fe(CN)〗_6^(4-), shows that the intensities of the anodic and cathodic peaks don’t increase when the working electrode is based on carbon paste modified with the raw clays (AH or DI), whereas the peaks intensities increase significantly when the working electrode consists of carbon paste modified with organoclays. This increase in the intensity of the current indicates an improvement in the surface conductivity of the carbon paste electrode when they are modified with organoclays. When the working Electrode is based on organoclays modified carbon paste, the potential differences (ΔEp) are ranged between 140 and 170 mV, which are lower than those of the unmodified carbon paste electrode (330 mV) and those modified with raw clays (520 mV). This indicates an easy electron transfer process on the surface of the organoclays modified carbon paste electrodes.

This study was conducted to examine the moderating and mediating effect of ego - resilience, parenting attitude, and peer attachment in the relation between smartphone dependency and aggression. Participants were 1,863 youths using a smartphone among the first middle school students responded in the 7th Korean Children and Youth Panel Survey (KCYPS) conducted by the National Youth Policy Institute in Korea. The data were analyzed by descriptive statistics, a correlation, and a hierarchical regression analysis. First, ego-resilience showed a partial mediating effect on the relationship between smartphone dependency, aggression and significant moderating effects were revealed. Second, parenting behavior showed a partial mediating effect on the relationship between smartphone dependency and aggression, with no moderating effects seen. Third, peer attachment had a partial mediating effect on the relationship between smartphone dependency and aggression, with no moderating effects seen. The research suggested the mental health and growth of students could be improved by applying various nursing and health care programs to improve ego-resilience, parenting behavior and peer attachment as they grow into adulthood.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

This study explores the implementation of an interdisciplinary curriculum in product and media design education and its impact on knowledge innovation and competency development. The curriculum is based on scaffolding theory, incorporating design proposals, workshops, digital design, marketing tests, and marketing activities guided by teachers and mentors from a branded ceramic workshop. The research findings demonstrate that the interdisciplinary curriculum facilitates knowledge innovation and fosters the development of students' professional skills, creativity, and problem-solving skills. The study also highlights the importance of stable scaffolding, including artefact, peer, and teacher support, which significantly contributes to cultivating transformational competencies, as outlined in the 2030 OECD Learning Compass. Additionally, the collaboration with Shanshing Four Seasons Celadon Studio on a patented ceramic product, "Funny Monkey," is a tangible example of the journey towards a triple-helix knowledge economy. This research underscores the importance of interdisciplinary curricula in promoting knowledge innovation and integrating transformational competencies in education. Scaffolding theory provides practical guidance for student learning and teaching strategies, presenting a sustainable roadmap for developing interdisciplinary curricula and offering a concrete and transferable pedagogical prototype for educational innovation.

Music and language are hypothesized to share neural resources, particularly at the level of syntax processing. Recent reports suggest that attention modulates this sharing of neural resources, but the time-course of the effects of attention, and the degree to which attention operates similarly on music and language, are yet unclear. In this EEG study we manipulate the syntactic structure of simultaneously presented musical chord progressions and garden-path sentences in a modified rapid serial visual presentation paradigm, while varying top-down attentional demands to the two modalities. The Early Right Anterior Negativity (ERAN) was observed in response to both attended and unattended musical syntax violations. In contrast, an N400 was only observed in response to attended linguistic syntax violations, and a P3 only in response to attended musical syntax violations. Results show that top-down allocation of attention indeed affects the processing of syntax in both music and language, with different neural resources acting upon the two modalities particularly at later stages of cognitive processing. However, the processing of musical syntax at an earlier stage of the perceptual-cognitive pathway, as indexed by the ERAN, is partially automatic, and is strongly indicative of separate neural resources for music and language.

Controversy exists on whether animal and plant proteins influence obesity differently. The purpose of this study was to evaluate the association between total, animal, and plant protein intake with the obesity index and renal function in Korean adults. Study participants included Korean adults aged 60 years or older from the Korean National Health and Nutrition Examination Survey in 2013-2014. Height, weight, and waist circumference (WC) were measured and the body mass index (BMI) was calculated. One-day 24-hour recall data were used to estimate the daily total, animal, and plant protein intake. Glomerular filtration rate (GFR) was calculated by using the Modification of Diet in Renal Disease (MDRD) equation. General linear modellings were used to assess the relationships between protein intake, BMI and WC. The mean age was 69.2 ± 0.2 years, 44.2% were male. The total daily protein intake was 1.1 ± 0.02 g/kg/d and 0.9 ± 0.02 g/kg/d for males and females, respectively. Only one third of protein intake was from animal sources. In males, BMI (p < 0.001, p = 0.016, p < 0.001 respectively) and WC (p < 0.001, p = 0.010, p < 0.001, respectively) decreased as daily intake of plant protein (g/kg/d), animal protein (g/kg/d) and total protein (g/kg/d) increased. Similar associations were shown in Korean female. GFR was not associated with protein intake regardless of protein source in both sexes. In Korean adults aged 60 years or older, the protein intake was associated with a favorable obesity index without decrease in renal function. The effect was similar in both male and females, with both animal and plant proteins.

Large structures such as wind turbines are subject to environmental factors and varying operational loads which may result in structural damage, making components of these large structures prone to performance and mechanical degradation. The use of high-definition optical vision sensors in digital image correlation (DIC) allow for the application of a non-destructive image registration technique in which it measures finite three-dimensional deformations on surfaces through correlations of a unique pattern or set of unique localized patterns. However, the physical placement of an artificial marker such as a unique speckled pattern on the surface of the structure is time-consuming and often impractical for large structures. Therefore, we propose a novel auto-mated methodology that searches and segments salient and unique regions of an image as well as for all subsequent images to assist in performing efficient displacement measurements for vibrational study and structural health monitoring purposes. Our algorithm is validated on a con-trolled set of images, as well as on a small structure and large real-world wind turbine, which suggests the algorithm’s efficacy without the use of artificial markers for large structural health monitoring.