In IP networks, packet forwarding is destination-based and hop-by-hop, and routes are built as needed. Kwong et al. introduced a protection routing in which packet delivery to the destination node can proceed uninterrupted in the event of any single node or link failure. He then shows that “whether there is a protection routing to the destination” is NP-complete. Tapolcai find that two completely independent spanning trees, abbreviated as CISTs, can be used to configure the protection routing. In this paper, we propose dual protection routing trees, denoted as dual-PRTs to replace CISTs, which are less restrictive than CISTs. Next, we propose a transformation algorithm that uses dual-PRTs to configure the protection routing. Taking complete graphs Kn, complete bipartite graphs Km,n, hypercubes Qn, locally twisted cubes LTQn as examples, we provide a recursive method to construct dual-PRTs on them. This article will show that there are no two CISTs on K3,3, Q3, and LTQ3, but there exist dual-PRTs that can be used to configure the protection routing. As shown in the performance evaluation of simulation results, for both Qn and LTQn, we get the average path length of protection routing configured by dual-PRTs is shorter than that by two CISTs.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Urbanization is considered as a main indicator of regional economic development due to its positive effect on promoting industrial development; however, many regions, especially developing countries, are troubled by its negative effect — the aggravating environmental pollution. Many researchers have indicated that rapid urbanization stimulated the expansion of industrial production scale and increased industrial pollutant emissions. However, this judgement contains a grave deficiency in that urbanization not only expands industrial production scales but can also increase industrial labour productivity and change the industrial structure. To modify this deficiency, we first decompose the influence which urbanization impacts on industrial pollutant emissions into the scale effect, the intensive effect and the structure effect by using the Kaya Identity and the LMDI Method; second, we perform an empirical study of the three effects’ impacts by applying the spatial panel model with data from 282 Chinese cities between 2003 and 2013. Our results indicate that (1) there are significant reverse U-shapes between Chinese urbanization rate and its industrial pollutant emissions; (2) the scale effect and the structure effect have aggravated Chinese industrial waste water discharge, sulphur dioxide emissions and soot (dust) emissions, while the intensive effect has generated a decreasing and ameliorative impact on that aggravated trend. The definite relationship between urbanization and industrial pollutant emissions depends on the combined influence of the scale effect, the intensive effect and the structure effect; (3) there are significant spatial autocorrelations of industrial pollutant emissions between Chinese cities, but the spatial spillover effect from other cities does not aggravate local urban industrial pollutant emissions, we offer an explanation to this contradiction that the vast rural areas surrounding Chinese cities have served as sponge belts and have absorbed the spatial spillover of cities’ industrial pollutant emissions. According to the results, we argue that this type of decomposition of the influence into three effects is necessary and meaningful, it establishes a solid foundation for understanding the relationship between urbanization and industrial pollutant emissions, and effectively helps to meet relative policy making.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

Aims:To update analytic formulas for the overall efficacy of corneal collagen crosslinking (CXL) including both type-I and oxygen-mediated type-II mechanisms, the role of oxygen and the initiator regeneration. Study Design:modeling the kinetics of CXL in UV light and using riboflavin as the photosensitizer.Place and Duration of Study:New Taipei City, Taiwan, between June, 2021 and July, 2021.Methodology:Coupled kinetic equations are derived under the quasi-steady state condition for the 2-pathway mechanisms of CXL. For type-I CXL, the riboflavin (RF) triplet state [T] may interact directly with the stroma collagen substrate [A] to form radical (R) and regenerate initiator. For type-II process, [T] interacts with oxygen to form a singlet oxygen [¹O₂]. Both reactive radical (R) and [¹O₂], can relax to their ground state, or interact with the substrate [A]) for crosslinking. Based on a safety dose, the minimum corneal thickness formula is derived. Results:Our updated theory/modeling showed that oxygen plays a limited and transient role in the process, in consistent with that of Kamave [2]. In contrary, Kling et al [3] believed that type-II is the predominant mechanism, which however conflicting with the epi-on CXL results. For both type-I and type-II, a transient state conversion (crosslink) efficacy in an increasing function of light intensity (or dose), whereas, its steady state efficacy is a deceasing function of light intensity. RF depletion in type-I is compensated by the RF regeneration term (RGE) which is a decreasing function of oxygen. For the case of perfect regeneration case (or when oxygen=0), RF is a constant due to the catalytic cycle. Unlike the conventional Dresden rule of 400 um thickness, thin cornea CXL is still safe as far as the dose is under a threshold dose (E*), based on our minimum thickness formula (Z*). Our formula for thin cornea is also clinically shown by Hafez et al forultra thin (214 nm) CXL. Conclusion: For both type-I and type-II, a transient state conversion (crosslink) efficacy in an increasing function of light intensity (or dose), whereas, its steady state efficacy is a deceasing function of light intensity. Ultra thin cornea is still safe as far as it is under a threshold dose (E*), based on our minimum thickness formula.

Plasminogen activator inhibitor-1 (PAI-1) has a significant role in fibrinolysis, atherogenesis, cellular senescence, and chronic inflammation. OSA (obstructive sleep apnea) leads to increased PAI-1 levels and the development of cardiovascular disease (CVD). The aim of this study was to determine the effects of CPAP therapy in patients with severe OSA on coagulation parameters and PAI-1. This prospective, controlled study enrolled 57 patients who were newly diagnosed with severe OSA, 37 of whom had had a good CPAP adherence after 6 months of therapy (usage of the device for at least 4 h per night), and their data were analyzed. The analysis showed a statistically significant increase in D-dimer values (415 (316.5-537.5) before CPAP therapy vs. 499 (327-652) after therapy, p = 0.0282) and a decrease in fibrinogen values (3.665 ± 0.752 before CPAP therapy vs. 3.365 ± 0.771) after therapy, p = 0.0075)). The PAI-1 concentration values before and after CPAP therapy did not differ significantly (17.35±7.01 ng/ml before CPAP therapy vs. 17.42±6.99 ng/ml after therapy, p = 0.9367). This study shows a tendency to improve the fibrinolytic capacity in patients with OSA after CPAP therapy although PAI-1 levels did not differ significantly.

Acellular bacterial ghosts (BGs) are empty non-living bacterial cell envelopes, commonly generated by controlled expression of the cloned lysis gene E of bacteriophage PhiX174. In this study, Vibrio parahaemolyticus ghosts (VPGs) were generated by chemically induced lysis and the method is based on minimum inhibitory concentration (MIC) of sodium hydroxide (NaOH), acetic acid, boric acid, citric acid, maleic acid, hydrochloric acid and sulfuric acid. The MIC values of the respective chemicals were 3.125, 6.25, < 50.0, 25.0, 6.25, 1.56 and 0.781 mg/ml. Except boric acid, the lysis efficiency was reached more than 99.99% at 5 min after treatment of all chemicals. Among those chemicals, NaOH-induced VPGs showed completely DNA-free that was confirmed by quantitative real-time PCR. Besides, lipopolysaccharides (LPS) extracted from the NaOH-induced VPGs showed no distinctive band on SDS-PAGE gel after silver staining. On the other hand, LPS extracted from wild-type bacterial cells as well as the organic acids-induced VPGs showed triple major bands and LPS extracted from the inorganic acids-induced VPGs showed double bands. It suggests that some surface structures in LPS of the NaOH-induced VPGs may be lost, weakened or modified by the MIC of NaOH. Nevertheless, Limulus amoebocyte lysate assay revealed that there is no significant difference in endotoxic activity between the NaOH-induced VPGs and wild-type bacterial cells. Macrophages exposed to the NaOH-induced VPGs at 0.5 × 106 CFU/mL showed cell viability of 97.9%, however the MIC of NaOH did not reduce the cytotoxic effect of wild-type bacterial cells. Like Escherichia coli LPS, the NaOH-induced VPGs are an excellent activator of pro-inflammatory cytokines (IL-1β and iNOS), anti-inflammatory cytokine (IL-10) and dual activities (IL-6) in the stimulated macrophage cells. On the other hand, the induction of TNF-α mRNA was remarkable in the macrophages exposed with wild-type cells. Scanning electron microscopy showed the formation of trans-membrane lysis tunnel structures in the NaOH-induced VPGs. SDS-PAGE and agarose gel electrophoresis also confirmed that cytoplasmic proteins and genomic DNA released from the VPGs to culture medium through the lysis tunnel structures. Taken together, all these results indicated that the NaOH-induced VPGs show the potency of safe, economical and effective inactivated bacterial vaccine candidate.

The synergistic features of a three-component, photoinitiating system (A/B/C) based on the measured data and proposed mechanism of Liu et al. are analyzed. The co-initiators/additives B and C have dual-functions of : (i) regeneration of photoinitiator A, and (ii) generation of extra radicals for enhanced conversion efficacy (CE). The synergistic effects led to higher CE for both free radical polymerization (FRP) and cationic polymerization (CP). The CE of FRP has 3 terms due to the direct (tyep-I) coupling of the triplet state of A with the monomer (M) and the coupling of the two radicals, R and R', with M. The CE of CP has a transient state proportional to the effective absorption constant (b), the light intensity (I) and initiator concentration (A0), but a steady state is independent of the light intensity (I). For the CE of FRP, the contribution from radical R had two cases: (i) linear dependence on T=bIA0, or (ii) nonlinear square root dependence T0.5. The synergistic effects led to higher conversion of FRP and CP, consistent with the measured results. The theoretically predicted new features include: (i) co-initiator [C] which always enhances both FRP and CP conversions, and (ii) co-initiator [B] which leads to more efficient FRP, but it also reduces CP.

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

This article presents, for the first time, comprehensive model based on the proposed mechanism of Rahal et al [17], Bonardi {20], Tar et al [20], and Mau et al [24], for 3-component systems of G1/Iod/EDB, G1/Iod/amine (in gold chloride), and Iod/Benzoic/Borate (for reduced oxygen inhibition) for the hybri free radical (FRP) and cationic (CP) photopolymerization of interpenetrated polymer network (IPN) systems. Analytic formulas are developed to explore the new features including: (i) conversion efficacy(CE) of FRP is an increasing function of the light intensity (I), the effective absorption coefficient (b), for transient state, whereas, CE at steady-state is independent to the light intensity; (ii) initiator regeneration (RGE)
provides a catalytic cycle for improved CE for FRP and CP; (iii) in the IPN system, the synergic effects due to the co-exist of FRP and CP include: (i) CP can increase the medium viscosity limiting the diffusional oxygen replenishment, such that OIH is reduced; (ii) the cationic monomer also acts as a diluting agent for the radical polymer network, and (iii) the exothermic property of the CP polymerization. We have proposed ascaling law for the transient and steady-state dependence of CE on the key parameter P=bIC₀, given by a an m-order power law of P^m, with m = 0.5 to 1.5, depending on various conditions. The CE also has an optimal value for maximum CE. The presented comprehensive model (with minimum mathematics) focusing on the enhancement mechanisms/pathways, provides analytic formulas which can be used to analyze reported data, and, more importantly, serves as guidance for exploring new functional materials or new kinetic schemes for improved conversion or procedures for both industrial and medical applications such as additive manufacturing (AM), 3D and 4D bioprinting. Finally, we have proposed new directions/experiments based on our theoretical predictions.

Purpose: To derive and provide analytic formulas for accommodative gain of presbyopia eyes. via sclera ablation and/or thermal shrinkage such that lens is reshaped an/or its positon is shifted. New mechanisms are also proposed. Study Design: To increased accommodation of presbyopia. Place and Duration of Study: New Taipei City, Taiwan, between June, 2021 and July, 2021. Methodology: Accommodation gain is calculated by a 4-component theory, in which the rate functions are derived by an effective eye model for the change of anterior curvature of the lens and its anterior shift. The measured data of accommodative response of the lens versus the lens curvature change and anterior shift are analyzed. The measured net change of the posterior vitreal zonules (PVZ) length and the space between the ciliary body and lens (CLS) during the accommodation are also analyzed. Results: The accommodative gain (AG) is mainly due the change of lens anterior curvature and its anterior shift. The AG per diopter change of the reshaped lens is 0.62 to 0.68 by our formulas, comparing to the measured average value M'=0.69. The efficacy of LASA (or AG) is proportional to the amount of scleral tissue removed (or shrinkaged), such that more space is produced for the change of PVZ and CLS from a UCS to AS for accommodation. Conclusion: The AG is proportional to the amount of scleral tissue removed (or shrinkaged), such that more space is produced for the change of PVZ and CLS from a UCS to AS for accommodation.

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

To resolve the controversial issues of UV-light-initiatedcornealcollagen cross-linking (CXL) by theoretical formulas and measured clinical outcomes. The controversial issues are addressed and resolved by analytical formulas including: the validation of Bunsen Roscoe law (BRL), the cutoff light intensity, the minimum corneal thickness, the demarcation line depth, the role of oxygen riboflavin (RF) concentration. The overall CXL efficacy is governed by UV-A light intensity, dose, exposure time, mode of exposure (pulsed or CW), riboflavin concentration, diffusion and drops pre-operation and interoperation administration, concentration of oxygen in the stromal tissue (pre-op and inter-op), and environmental conditions. The length of the riboflavin presoaking time and viscosity of the riboflavin film also affect the crosslink depth. Analytic formulas are derived for the scaling laws for type-I and type-II efficacy, given by the square-root of light intensity, and light dose, respectively. The controversial issues of CXL may be partially resolved via analytic formulas, and compared with measurements. The scaling laws of type-I and type-II efficacy are different and given by analytic formulas. Our formulas also predict the maximum light intensity and the minimum corneal thickness, which are consistent with measurements.

All living cells maintain a charge distribution across their cell membrane (membrane potential) by carefully controlled ion fluxes. These bioelectric signals regulate cell behavior (such as migration, proliferation, differentiation) as well as higher-level tissue and organ patterning. Thus, voltage gradients represent an important parameter for diagnostics as well as a promising target for therapeutic interventions in birth defects, injury, and cancer. However, despite much progress in cell and molecular biology, little is known about bioelectric states in human stem cells. Here, we present simple methods to simultaneously track ion dynamics, membrane voltage, cell morphology, and cell activity (pH and ROS), using fluorescent reporter dyes in living human neurons derived from induced neural stem cells (hiNSC). We developed and tested functional protocols for manipulating ion fluxes, membrane potential, and cell activity, and tracking neural responses to wounding and re-innervation in vitro. Finally, using morphology sensor, we tested and quantified the ability of physiological actuators (neurotransmitters and pH) to manipulate nerve wound re-innervation. These methods are not specific to a particular cell type and should be broadly applicable to the study of bioelectrical controls across a wide range of combinations of models and endpoints.

Public health is an important aspect of community activities, making research on health necessary because it is a crucial field in maintaining and improving the quality of life in society as a whole. Research in public health allows for a deeper understanding of the health problems faced by a population, including disease prevalence, risk factors and other determinants of health. This work aims to explore the potential of hospital patient data analysis as a valuable tool for understanding community implications and deriving insights for effective community health interventions. The study recognises the significance of harnessing the vast amount of data generated within hospital settings to inform population-level health strategies. The methodology employed in this study involves the collection and analysis of deidentified patient data from a representative sample of a hospital in Indonesia. Various data analysis techniques, such as statistical modelling, data mining and machine learning algorithms, are utilised to identify patterns, trends and associations within the data. A program written in Python is used to analyse patient data in a hospital for five years from 2018 to 2022. These findings are then interpreted within the context of public health implications, considering factors such as disease prevalence, socioeconomic determinants and healthcare utilisation patterns. The results of the data analysis provide valuable insights into the public health implications of hospital patient data. The research also covers prediction for the patient data to the hospital based on disease, age and geographical residence. The research prediction shows that in 2023, the number of patients was not considerably affected, but in in March to April 2024, the number significantly increased to 10,000 patients. These recommendations encompass targeted prevention strategies, improved healthcare delivery models and community engagement initiatives. The research emphasises the importance of collaboration between healthcare providers, policymakers and community stakeholders in implementing and evaluating these interventions.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

Purpose:To explore (theoretically) the key parameters and their influence on the time profiles of photosensitizer (riboflavin), free radicals, singlet oxygen, oxygen and the efficacy of corneal collagen crosslinking (CXL)in both type-I and oxygen-mediated type-II mechanisms, specially the role of oxygen and the initiator regeneration. Methodology:Coupled kinetic equations are derived and numerically solved under the quasi-steady state condition for the 2-pathway mechanisms of CXL. The key parameters explored include (bI, V, Q', K, K',Q,P) and their influence on the time profiles of photosensitizer (riboflavin, C), radicals (R), singlet oxygen(S), oxygen (X) and efficacy (E), parameters of (K,K',Q) define the relative strength of type-I and type-II process. The oxygen depletion profile, X(t), and the associated singlet oxygen, S(t), depend on the parameters of V, Q' and the initial value of oxygen. The coupling strength given by (bI) governs almost all profiles, where b is an effective absorption parameter and I is the UV light intensity.Results:Our numerical method for CXL dynamic profiles demonstrated the following important features: (i) Type-I and type-II coexit in CXL, in the presence of oxygen. However, there is no type-II when oxygen is depleted or in a condition without oxygen. (ii) Type-I with bimolecular termination, the radical R(t) is a function of [K'(bIgC)]^0.5, leading to the steady-state efficacy given by a scaling law of 1/(bI)^0.5, in contract to that of type-II which is almost independent to the light intensity. (iii) The depletion rate (2 to 5 minutes) of X(t) is much faster than that of C(t) (10 to 20 minutes), (iv) Thepure type-II profile, has a transition point from straight line to saturating curve and matches the depletion point of singlet oxygen S(t). (v) Improved CXL efficacy of type-I and type-II may be achieved by external supply of photoinitiator (riboflavin) and oxygen, respectively.

In manual maintenance inspections of large-scaled photovoltaic (PV) or rooftop PV systems, several days are required to survey the entire PV field. To improve reliability and shorten the amount of time involved, this study proposes an electrical examination based method for locating multiple faults in the PV array. The maximum power point tracking (MPPT) algorithm is used to estimate the maximum power of each PV panel; this is then compared with metering the output power of PV array. Power degradation indexes are parameterized to quantify the degradation between maximum power and metered output power. Bidirectional hetero-associative memory (BHAM) networks are then used to locate multiple faults within the entire PV field. For a rooftop PV system with two strings, as seen in Figure 1, experimental results demonstrate that the proposed model has computational efficiency for real-time applications and that its algorithm is easily implemented in a mobile intelligent vehicle.

The quality of healthcare services is a very important indicator of social welfare in developed and emerging countries. Good quality levels are critical to ensuring patient safety, improving health outcomes, increasing patient satisfaction, optimizing resource utilization, and meeting regulatory requirements. The stable and sustainable operation of medical institutions urgently requires the establishment of a reliable and effective medical quality performance evaluation platform. However, the complexity of the evaluation process, involving numerous evaluators and the consideration of different subjective and objective criteria, poses significant challenges and essentially constitutes a group multi-criteria decision-making problem. This article uses the overall medical environment of the institution, medical service attitude, medical security, administrative service measures, etc. as measurement standards to deal with this challenge. It proposes a medical service quality measurement model suitable for both qualitative and quantitative analysis. In view of the heterogeneity of information, the two-tuple fuzzy language calculation method is introduced to enable evaluators to skillfully manage diverse information and effectively avoid potential information omission problems in the subjective evaluation integration process. The effectiveness and feasibility of the model were demonstrated by applying it to the operational framework of a medical institution in central Taiwan.

The synergetic features of a three-component photoinitiating systems (A/B/C) based on the measured data and proposed mechanism of Liu et al (Polymers, 2020, 12(6), 1394) are analyzed. The co-initiators/additives B and C have dual functions of : (i) regeneration of photoinitiator A and (ii) generation of extra radicals. The synergic effects lead to higher conversion of free radical polymerization (FRP) and cationic polymerization (CP). The key factors and rate constants influencing the conversion efficacy are explored by analytic formulas. Enhancing strategies for various photopolymerization systems are summarized including one component (or monomer) and one-wavelength, two-component and one, two and three-wavelength, and three-component, one-wavelength system. The synergetic effects for higher monomer conversion can be achieved by co-initiators for extra radicals and multiple wavelengths for reduced oxygen-inhibition. Co-initiator B, however, might also reduces the CP radical produced by initiator C. The conversion rate of FRP is proportional to the square root of the light intensity (I), absorption (b) and the initiator initial concentratios (A0, B0, C0), whereas CP is proportional to the linear power of a parameter defined as P=bIA0C0, a stronger dependence than FRP. The CP conversion is governed by a steady-state value proportional to P, and a rate fucntion defining the depletion rate of [A][C], or the increasing rate of the conversion profile. The measured results of Liu et al (Polymers, 2020, 12(6), 1394) are well analyzed and matching the predicted features of our modeling. The specific systems analyzed are: benzophenone derivatives (A) ethyl 4-(dimethylamino)benzoate (B), and (4-tert-butylphenyl)iodonium hexafluorophosphate (C) under a UV (365 nm) LED irradiation; and monomers of trimethylolpropane triacrylate (TMPTA, for FRP) and (3,4- epoxycyclohexane)methyl 3,4-epoxycyclohexylcarboxylate (EPOX, for CP).

This article presents, for the first time, the kinetics and the general conversion features of free radical polymerization (FRP) in a 3-component system (A/B/N), with [A] being the initiator, and [B] and [N] are additives, based on the proposed mechanism of Rahal et al. Higher FRP can be achieved by additives [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals (R) via the radicals (S' and S) produced by N.The initiator (coumarin) shows a dual photo-oxidation and photo-reduction character for high efficacy. The FRP conversion efficacy (CE) depends not only on the property of the initiator [A], the additives [B] and [N}, but also the types of monomers. For example, when [A]=CoumC, [A]/NPG is more efficient than [A]/Iod, but revserse trend occurs in some monomers. However, 2-component systems (with CE=0% to 80%) are always less efficient than that of 3-component systems (with CE=70% to 86%, in TMPTA). Specific systems with [A]=coumarins, [B]=Iodonium salt, and N=NPG are analyzed. Analytical formulas for the role of each component concentration, light intensity and coupling rates on the conversion efficacy are derived.

The synergic features and enhancing strategies for various photopolymerization systems are reviewed by kinetic schemes and the associated measurements. The important topics include: (i) photo crosslinking of corneas for the treatmnet of corneal deseases using UVA-light (365 nm) light and riboflavin as the photosensitizer; (ii) synergic effects by a dual-function enhancer in a 3-initiator system; (iii) synergic effects by a 3-initiator C/B/A system, having an electron-transfer and oxygen-mediated energy-transfer pathways; (iv) copper-complex (G1) photoredox catalyst in G1/Iod/NVK systems for free radiical (FRP) and cationic photopolymeriation (CP); (v) radical-mediated thiol-ene (TE) photopolymerizations; (vi) superbase photogenerator based-catalyzed thiol−acrylate Michael (TM) addition reaction; and the combined system of TE and TM usinghual wavelength; (vii) dual-wavelength (UV and blue) controlled photopolymerization confinement (PC); (viii) dual-wavelength (UV and red) selectively controlled 3D printing; and (ix) 3-wavelength selectively controlled in 3D printing and additive manufacturing (AM). With minimum mathematics, we present ( for the first time), the synergic features and enhancing strategies for various systems of multi-commponents, initiators, monomers, and under one- two- and there-wavelength light. Therefore, this Review provides not only the bridging between modeling and measurements, but also guidances for further experimantal stuides and new applications in 3D printings and additive manufacturing (AM), based on the innovative concepts (kinetics/schemes).

This article presents, for the first time, the kinetics and the general conversion features of a 3-component system, BT(BC)/iodonium/Amine, based on proposed mechanism of Liu et al, for both free radical polymerization (FRP) of acrylates and the free radical promoted cationic polymerization (CP) of epoxides using the new multi-functional initiator of benzophenone–triphenylamine (BT). The additives, iodonium and EDB, have the dual function of (i) regeneration BT and (ii) produce of extra radicals for improved FRP and CP. Analytic formulas are developed to explore the new features including: (i) the conversion efficacy (CE) of FRP is an increasing function of the light intensity, the effective absorption coefficient, and the concentration sum of each of the components, BT, Iod, amine, for transient state. However, CE at steady-state is independent to the light intensity; (ii) the trifunctional hybrid structures of BT3 leads to larger light absorption than other types of BT; it also provides more active sites for the H-abstraction in the presence of EDB, leading to high CE; (iii) the efficacy of FRP is an increasing function of the amine (EDB) concentration, in contrast to that of CP having an opposite dependence; (iv) the consumption rate of BT3 in the BT3/ Iod/EDB system is slower than that of the BT3/Iod system due to photoredox catalytic cycle, and the larger initiator regeneration (RGE)
in the three-component system. A comprehensive model is also proposed that the CE (for both FRP and CP) is governed by (N_jK_jbI), whereas more complex formulas are developed; where Kj is an effective rate constant proportional to the electron transfer quantum yield, and the combined effects of other coupling rate constants; b is an effective absorption coefficient given by the light absorption and excited state quantum yield.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

In recent years, with the popularity of smart mobile devices, the interaction between devices and users, especially in the form of voice interaction, has become increasingly important. If smart devices can understand more users' emotional states through voice data, more customized services can be provided for users. This paper proposes a novel machine learning model for speech emotion recognition, which combines convolutional neural networks (CNN), long short-term memory neural networks (LSTM), and deep neural networks (DNN), called CLDNN. To make the designed system can recognize the audio signal closer to the human auditory system does, this article uses the Mel frequency cepstral coefficients (MFCCs) of audio data as the input of the machine learning model. First, the MFCCs of the voice signal is extracted as the input of the model, and the feature values of the data are calculated using several local feature learning blocks (LFLB) composed of one-dimensional CNN. Because the audio signals are time-series data, the feature values obtained from LFLBs then input into LSTM layer to enhance the learning on time-series level. Finally, fully connected layers are used for classification and prediction. Three databases RAVDESS, EMO-DB and IEMOCAP are used for the experiments in this paper. The experimental results show that the proposed method can improve the accuracy compared to other related researches in speech emotion recognition.

Hydroa vacciniforme (HV) is a rare form of photosensitivity disorders in children and is frequently associated with Epstein-Barr virus (EBV) infection, whereas HV-like lymphoproliferative disorders (HVLPD) describe a spectrum of EBV-associated T-cell or NK-cell lymphoproliferations with HV-like cutaneous manifestations, including EBV-positive HV, atypical HV, and HV-like lymphoma. Classic HV occurs in childhood with vesiculopapules on sun-exposed areas, which is usually induced by sunlight and ultraviolet irradiation, and mostly resolves by early adult life. Unlike classic HV, atypical or severe HV manifests itself as recurrent papulovesicular eruptions in sun-exposed and sun-protected areas associated occasionally with facial edema, fever, lymphadenopathy, oculomucosal lesions, gastrointestinal involvement, and hepatosplenomegaly. Notably, atypical or severe HV may progress to EBV-associated systemic T-cell or natural killer (NK)-cell lymphoma after a chronic course. Although rare in the United States and Europe, atypical or severe HV and HV-like lymphoma are predominantly reported in children from Asia and Latin America with high EBV DNA levels, low numbers of NK cells, and T cell clones in the blood. In comparison with the conservative treatment used for patients with classic HV, systemic therapy such as immunomodulatory therapy is recommended as the first-line therapy for patients with atypical or severe HV. This review aims to provide an integrated, overview of current evidence and knowledge of HV and HVLPD to elucidate the pathophysiology, practical issues, environmental factors, and the impact of EBV infection.

Objective: This study investigated the effect of the hierarchical medical system under the national health insurance program on resident’s healthcare-seeking behavior in Taiwan. Background: Healthcare authorities in Taiwan initiated the allowance reduction of outpatient visits at regional hospitals and higher hierarchical hospitals from 2018. The ultimate goal is to implement a hierarchical medical system and provide the residents accessible as well as consistent medical services. Methods: This research was conducted through the questionnaire survey method and data were collected between August and December 2018 from the records of subjects who had recently sought medical attention. A total of 1,340 valid questionnaires were returned. Results: Regarding the effect on healthcare-seeking behavior, the following factors were significant: being aged between 40 to 49 (p＜.1), subjects with an educational background of junior high school (p＜.05), those who were not aware of the policy (p＜.001), and an awareness about both the hierarchical medical system and the policy to reduce outpatient visits to large hospitals (p＜.001). Conclusion: The public should be made aware about the hierarchical medical system to improve healthcare.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

This paper reports the efforts made and experiences gained in developing the Flood Prevention and Emergency Response System (FPERS) powered by Google Earth Engine, with focus on its applications at the three stages of floods. At the post-flood stage, FPERS integrates various remote sensing imageries, including Formosat-2 optical imagery, to detect and monitor barrier lakes, synthetic aperture radar imagery to derive an inundation map, and high-spatial-resolution photographs taken by unmanned aerial vehicles to evaluate damage to river channels and structures. At the pre-flood stage, a huge amount of geospatial data are integrated in FPERS and are categorized as typhoon forecast and archive, disaster prevention and warning, disaster events and analysis, or basic data and layers. At the during-flood stage, three strategies are implemented to facilitate the access of the real-time data: presenting the key information, making a sound recommendation, and supporting the decision-making. The example of Typhoon Soudelor in August of 2015 is used to demonstrate how FPERS was employed to support the work of flood prevention and emergency response from 2013 to 2016. The capability of switching among different topographic models and the flexibility of managing and searching data through a geospatial database are also explained, and suggestions are made for future works.

Climate change and food security are the most relevant issues to be considered in sustainable agricultural development. The FAO’s initiative of climate-smart agriculture has attracted international attention. Since then, the smart agriculture (SA) has been recognized as the most influential trends in contributing to agricultural development. Therefore, encouraging farmers to adopt digital technologies and mobile devices into farming practices becomes a policy priority worldwide. However, there is limited literature available on psychologic factors that drive farmers’ intentions to adopt SA technologies. The purpose of this study is to investigate how farmer’s knowledge and attitude toward SA affects their adoption of smart technologies in Taiwan. A total of 321 farmers participated in the project’s survey in 2017 and 2018, from which the data was used to perform an OLS regression model of SA adoption. This study contributes to a preliminary understanding of relationship between innovation and adoption of SA technologies in a small-scale farming economic context. The findings suggest that the policy makers and R&D institutes need to concentrate on improving market access for well-known and high important SA technologies.

This article presents, for the first time, the kinetics and the general conversion features of a 3-initiator system (A/B/N), based on proposed mechanism of Mokbel et al, for both free radical polymerization (FRP) of acrylates and the free radical promoted cationic polymerization (CP) of epoxides using copper complex as the initiator. Higher FRP and CP conversion can be achieved by co-initiators concentration [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals S' and S. The FRP and CP conversion is proportional to, respectively, the nonlinear and linear power of bI[A][B], where b and I are the absorption coefficient and the light intensity, respectively. System in air has lower conversion than in laminate due to the oxygen inhibition effects. For thick samples (with thickness z), there is an optimal concentration [A*] which is inverse proportional (bzI), in contrast with very thin sample, in which the conversion is an increasing function of [A] and [B]. The unique feature of dark polymerization in CP conversion enables the polymerization to continue in living mode, in contrasts with that of the radical-mediated pathway in most conventional FRP. The measured results of Mokbel et al are well analyzed and matching the predicted features of our modeling.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

. This article presents, for the first time, the kinetics and the general conversion features of a 3-component system (A/B/N), based on proposed mechanism of Mau et al, for both free radical polymerization (FRP) of acrylates and the free radical promoted cationic polymerization (CP) of epoxides using various new copper complex (G2) as the initiator. Higher FRP and CP conversion can be achieved by co-additive of [B] and N, via the dual function of (i) regeneration [A], and (ii) generation of extra radicals. The FRP and CP conversion efficacy (CE) are proportional to the nonlinear power of bI[A][B], where b and I are the effective absorption coefficient and the light intensity, respectively. In the interpenetrated polymer network (IPN) capable of initiating both FRP and CP in a blend of TMPTA and EPOX, (as the monomer for FRP and CP, respectively), the synergic effects due to CP include:: (i) CP can increase viscosity limiting the diffusional oxygen replenishment, such that oxygen inhibition effects are reduced; (ii) the cationic monomer also acts as a diluting agent for the IPN network , and (iii) the exothermic property of the CP. Many new findings are explored via our analytical formuals include: (i) the CE of FRP is about twice of the CE of CP, due to the extra radicals involved in FRP; (ii) the catalytic cycle enhancing the efficacy is mainly due to the regenaration of the initiator, and (iii) the nonlinear dependence of light intensity of the CE (in both FRP and CP). For the first time, the catalytic cycle, synergic effects, and the oxygen inhibition are theoretically confirmed to support the experimental hypothesis. The measured results of Mau et al are well analyzed and matching the predicted features of our modeling. .

Ulcerative colitis (UC) is a chronic autoimmune disorder affecting the colonic mucosa. UC is a subtype of inflammatory bowel disease along with Crohn’s disease and presents with varying extraintestinal manifestations. No single etiology for UC has been found, but a combination of genetic and environmental factors is suspected. Research has focused on the role of intestinal dysbiosis in the pathogenesis of UC, including the effects of dysbiosis on the integrity of the colonic mucosal barrier, priming and regulation of the host immune system, chronic inflammation, and progression to tumorigenesis. Characterization of key microbial taxa and their implications in the pathogenesis of UC and colitis-associated cancer (CAC) may present opportunities for modulating intestinal inflammation through microbial-targeted therapies. In this review, we will discuss the microbiota-immune crosstalk in UC and CAC, as well as the evolution of microbiota-based therapies.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

The value of QuantiFERON in the diagnosis of tuberculosis and in the monitoring of the response to anti-tuberculosis treatment is unclear. The aims of this study were to evaluate the accuracy of the QuantiFERON-TB Gold In-Tube (QFT-GIT) test in the diagnosis of tuberculosis and in the monitoring of the response to anti-tuberculosis treatment in patients with active pulmonary tuberculosis (PTB). Between January 2013 and December 2015, 128 cases with active PTB and 128 controls with no mycobacterial infection, matched by age (within 3 years) and by the week that they visited Tainan Chest Hospital, were enrolled in the study. Serial testing by QFT-GIT at baseline and after 2 and 6 months of treatment was performed. At these time points, a comparison of the performance of QFT-GIT with that of sputum culture status among study subjects was conducted. Compared to baseline, 116 (87.2%) cases showed a decreased response, whereas 17 (12.8%) showed persistent or stronger interferon-gamma (IFN-γ) responses at 2 months. Their IFN-γ responses declined significantly from baseline to 2 months (median, 6.32 vs. 4.12; P < 0.005). The sensitivity values of the QFT-GIT test for the detection of pulmonary tuberculosis at cut-off points of 0.35 IU/ml, 0.20 IU/ml, and 0.10 IU/ml were 74.4%, 78.2%, and 80.5%, respectively. The specificity values at cut-off points of 0.35 IU/ml, 0.20 IU/ml, and 0.10 IU/ml were 66.2%, 63.9%, and 57.1%, respectively. Our results support the QFT-GIT assay as a potential tool for diagnosing tuberculosis and for monitoring the efficacy of anti-tuberculosis treatment.

Blood testing is a crucial medical application. In this study, we applied Raman spectroscopy to test blood samples and obtained complete biological information, including the main components and compositions in these samples. Short-wavelength (532-nm green light) Raman scattering spectroscopy was conducted on samples of normal blood, abnormal blood in 3 types of preparation including whole blood, plasma, and serum, and the underlying information reflected by the biological characteristics detected in each sample type were analyzed. Raman spectroscopy results indicated that normal blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. Hemoglobin affects blood oxygen level. The characteristic peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. In addition, surface-enhanced Raman spectroscopy was used to collect biological signals that are difficult to obtain in conventional Raman spectroscopy, including those of small molecules such as hormones, antibodies, and enzymes. Changes in biological information collected in this manner can be used as a basis for potentially diagnosing clinical diseases.

The open hole tensile and flexural test of composites holds immense importance in aerospace and structural engineering. These tests provide critical insights into how composites perform under real-world conditions, allowing for the development of materials that meet rigorous standards, thereby ensuring the safety and durability of aircraft and other applications. This study investigates the influence of hole size on the open hole tensile (OHT) and flexural properties (OHF) of plane woven aramid/epoxy (AFRP), basalt/epoxy (BFRP), and aramid-basalt/epoxy (ABFRP) sandwiched laminates. Specimens with three different hole sizes viz., 4 mm, 6 mm, 8 mm were prepared and tested according to ASTM D5766 and ASTM D7264 for OHT and OHF performance respectively. Results indicated that the hybridization of aramid-basalt layers in a sandwich lay up significantly improved the mechanical performance when compared to only aramid laminate. However, with the increase in hole size the mechanical properties declined irrespective of the material. Basalt fibres showed higher hole sensitivity under tensile loading due to its brittle fracture mechanism while aramid fibres exhibited higher hole sensitivity under flexural loading which can be attributed to its the poor compressive strength. The effect of hole size on the damage mechanism has also been highlighted through scanning electron microscope (SEM). Major failure modes observed are delamination around the hole edges, ductile and brittle fibre fractures, and delamination.

In recent times, BERT based transformer models have become an inseparable part of the 'tech stack' of text processing models. Similar progress is being observed in the speech domain with a multitude of models observing state-of-the-art results by using audio transformer models to encode speech. This begs the question of what are these audio transformer models learning. Moreover, although the standard methodology is to choose the last layer embedding for any downstream task, but is it the optimal choice? We try to answer these questions for the two recent audio transformer models, Mockingjay and wave2vec2.0. We compare them on a comprehensive set of language delivery and structure features including audio, fluency and pronunciation features. Additionally, we probe the audio models' understanding of textual surface, syntax, and semantic features and compare them to BERT. We do this over exhaustive settings for native, non-native, synthetic, read and spontaneous speech datasets

The kinetics and efficacy profiles of photoinitiated polymerization are theoretically presented. For the same dose, lower light intensity achieves a higher steady-state-efficacy (SSE) in type-I; in contrast, type-II has an equal SSE. Higher light intensity has a faster rising efficacy, due to faster depletion of photoinitiator (PS) concentration. However, type-II process is also affected by the available oxygen. Higher light intensity produces more efficient singlet oxygen, resulting a higher transient efficacy, in which all intensities reach the same SSE when oxygen is completely depleted. With external oxygen, type-II efficacy increases with time, otherwise, it is governed only by the light dose, i.e., same dose achieves same efficacy. Moreover, type-II has an efficacy follows Bunsen Roscoe law (BRL), whereas type-I follows non-BRL. The measured type-I efficacy and gelation profile are analyzed by our analytic formulas. Schematics of the photocrosslinking stage defined by the availability of oxygen is developed, where both type-I and –II coexist until the oxygen is depleted. The overall efficacy may be enhanced by resupply of PS or oxygen during the light exposure. The roles of light dose and PS concentration on the efficacy of photoinitiated polymerization should be are governed a new concept of a volume efficacy (Ve), defined by the product of the crosslink (or gelation) depth (CD) and local [efficacy].

Optimal conditions for maximum efficacy of photoinitiated polymerization are theoretically presented. Analytic formulas are shown for the crosslink time, crosslink depth and efficacy function. The roles of photoinitiator (PI) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented. For optimal efficacy, a strategy via controlled PI concentration is proposed, where re-supply of PI in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced. Experimental data are analyzed for the role of PI concentration and light intensity on the gelation time and efficacy.

The kinetics and modeling of dual-wavelength controlled photopolymerization confinement (PC) are presented and measured data are analyzed by analytic formulas and numerical data. The UV-light initiated inhibition effect is strongly monomer-dependent and different monomers have different C=C bond rate constants and conversion efficacy. Without the UV-light, for a given blue-light intensity, higher initiator concentration (C₁₀) and rate constant (k’) lead to higher conversion, as also predicted by analytic formulas, in which the total conversion rate (R_T) is an increasing function of k’R, which is proportional to k[gB₁C₁]^0.5. However, the coupling factor b₁ plays a different role that higher b₁ leads to higher conversion only in the transient regime; whereas higher b₁ leads lower steady-state conversion. For a fixed initiator concentration C₁₀, higher inhibitor concentration (C₂₀) leads to lower conversion due to stronger inhibition effect. However, same conversion reduction was found for the same H-factor of H₀ = [b₁C₁₀ - b₂C₂₀]. Conversion of blue-only are much higher than that of UV-only and UV-blue combined, in which high C₂₀ results a strong reduction of blue-only-conversion, such that the UV-light serves as the turn-off (trigger) mechanism for the purpose of spatial confirmation within the overlap area of UV and blue light. For example, UV-light controlled methacrylate conversion of a glycidyl dimethacrylate resin formulated with a tertiary amine co-initiator, and butyl nitrite, subject to a continuous exposure of a blue light, but an on-off exposure of a UV-light. Finally, we developed a theoretical new finding for the criterion of a good material/candidate governed by a double ratio of light-intensity and concentration, [I₂₀C₂₀.]/[I₁₀C₁₀].

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

Currently, conventional spark-ignition engines face challenges in meeting the ever-growing demands of customers and increasingly stringent regulations regarding pollutant emissions. A combination of innovative strategies and carbon-neutral fuels is deemed necessary in order to further reduce fuel consumption and minimize engine emissions. The present work aims to assess the performance of combustion strategies using low-carbon content fuel, such as methanol M100, ignited by a plasma-assisted igniter (PAI) under ultra-lean conditions. The experimental campaign is conducted on a single-cylinder research engine at different engine speeds and low loads, moving up to the engine lean stable limits. To determine the benefits brought by the proposed strategy, referred to as M100-PAI, the obtained outcomes are compared with the ones obtained using market gasoline E5 ignited by the PAI system and conventional spark. The synergy between M100 (methanol) and Plasma Assisted Ignition (PAI) in internal combustion engines yielded notable benefits. This combination significantly improved combustion stability if compared to the other combinations tested, by extending the lean stable limit to λ=2.0, reducing cycle-to-cycle variability, and facilitating faster flame front acceleration, resulting in enhanced homogeneity. These enhancements, obtained with the combination M100-PAI, contributed to higher fuel efficiency showing a 10% efficiency gain over the combination E5-gasoline spark ignition.

Continuous research into the availability of phosphorus (P) in forest soil is critical for sustainable management of forest ecosystems. In this study, we used sequential chemical extraction and 31P-nuclear magnetic resonance spectroscopy (31P-NMR) to evaluate the form and distribution of inorganic P (Pi) and organic P (Po) in Casuarina forest soils of a subtropical coastal sand dune at Houlong in Taiwan. The soil samples were collected from humic (+2-0 cm) and mineral layers (mineral-I: 0-10, mineral-II: 10-20 cm) at two topographic locations (upland and lowland) by elevation. Sequential chemical extraction revealed that the NaOH-Po fraction, as moderately recalcitrant P, was the dominant form in humic and mineral-I layers in both upland and lowland soils, whereas the cHCl-Pi fraction was the dominant form in the mineral-II layer. Resistant P content, including NaOH-Pi, HCl-Pi, cHCl-Pi, and cHCl-Po fractions, was higher in the upland than lowland in the corresponding layers; however, labile P content, NaHCO3-Po, showed the opposite pattern. Content of resistant Pi (NaOH-Pi, HCl-Pi, and cHCl-Pi) increased significantly with depth, but that of labile Pi (resin-Pi and NaHCO3-Pi) and recalcitrant Po (NaHCO3-Po, NaOH-Po, and cHCl-Po) decreased significantly with depth at both locations. 31P-NMR spectroscopy revealed inorganic orthophosphate and monoesters-P as the major forms in this area. The proportions of Pi and Po evaluated by sequential chemical extraction and 31P-NMR spectroscopy were basically consistent. The results indicated that the soils were in weathered conditions. Furthermore, the P distribution and forms significantly differed between the upland and lowland by variation in elevation and eolian aggradation effects in this coastal sand dune landscape.

Cachexia is a complex metabolic syndrome characterized by loss of skeletal muscle, leading to a significant weight loss that impacts patient morbidity and mortality. Given the complexity of gene regulatory networks that control gene expression, our objective was to perform an integrative mRNA and miRNA profiling to identify genetic programs that capture essential mechanistic details that promote muscle atrophy in cancer cachexia. Here, we used RNA sequencing to analyze miRNAs and mRNAs expression profiles in tibialis anterior (TA) muscles of the Lewis lung carcinoma model of cancer cachexia. In addition, we compared these findings with RNA-Seq data from C2C12 myotubes treated in vitro with the cachectic factors tumor necrosis factor-alpha (TNF-α) and interferon-gamma (IFN-γ). Extracellular matrix (ECM) alterations were validated by picrosirius staining, western blot, and fractal dimension analyses. We found 1,008 mRNAs and 18 miRNAs differentially expressed in cachectic mice. This set of genes was associated with the ECM, proteolysis, and inflammatory response. Enrichment analysis of transcriptional factor binding sites revealed activation of the atrophy-related transcriptional factors: NF-κB, Stat3, AP-1, and FoxO. Furthermore, the integration of mRNA and miRNA expression profiles identified post-transcriptional regulation by miRNAs of genes involved in ECM organization, cell migration, transcription factors binding, ion transport, and FoxO signaling pathway. C2C12 myotubes treated with TNF-α and IFN-γ similarly down-regulate subsets of ECM genes, including collagens. Our integrative analysis of miRNA-mRNA co-profiles comprehensive characterized regulatory relationships of molecular pathways and revealed miRNAs targeting ECM-associated genes in cancer cachexia. We also confirmed in C2C12 myotubes that changes in ECM-associated genes are dependent on inflammatory signaling of the cytokines TNF-α and IFN-γ.

Tissue engineered heart valves can grow, repair, and remodel after implantation, presenting a more favorable long-term solution compared to mechanical and porcine valves. Achieving functional engineered valve tissue requires the maturation of human cells seeded onto valve scaffolds under favorable growth conditions in bioreactors. The mechanical stress and strain on developing valve tissue caused by different pressure and flow conditions in bioreactors are currently unknown. The aim of this study is to quantify the wall shear stress (WSS) magnitude in heart valve prostheses under different valve geometries and bioreactor flow rates. To achieve this, the study used fluid-structure interaction simulations to obtain the valve's opening geometries during the systolic phase. These geometries were then used in computational fluid dynamics simulations with refined near-wall mesh elements and ranges of prescribed inlet flow rates. The data obtained included histograms and regression curves that characterized the distribution, peak, and median WSS for various flow rates and opening configurations. The study also found that the upper region of the valve near the commissures experienced higher WSS magnitudes than the rest of the valve.

This research paper presents a new application of electroactive polyimide doped with gold nanoparticles (PI/AuNPs) as a chemiresistor sensor for detecting hydrogen sulfide gas. The synthesis of PI/AuNPs was done in a simple 3-step process of polymerization using the as prepared amine-capped aniline trimer (ACAT), followed by imidization, and doping. Spectral analyses via FTIR, LC-MS and ¹H-NMR confirmed the formation of amine-capped aniline trimer with a MW of 288 g mol^-1. Comparison of ACAT, BSAA, and PI FTIR spectra showed successful polymerization of the last, while XRD validated the incorporation of metal nanoparticles onto the polymer matrix showing characteristic diffraction peaks corresponding to gold. Furthermore, TEM, and FE-SEM revealed the presence of well-dispersed Au nanoparticles with an average diameter of about 60nm. The electroactive PI/AuNPs-based sensor showed a sensitivity of 0.29% ppm^-1 H₂S at a linear concentration range of 50 to 300 ppm H₂S (r = 0.9777). The theoretical limit of detection was found at 0.142 ppm or 142 ppb H₂S gas. The sensor provided a stable response reading at an average response time of 43±5 seconds, which was easily recovered after an average time of 99±5 seconds. The sensor response was highly repeatable and reversible with RSD values of 8.88%, and 8.60%, respectively. Compared with the performance of the conventional conducting polyaniline also doped with gold nanoparticles (PANI/AuNPs), the fabricated electroactive PI/AuNPs exhibited improved sensing performance making it a potential candidate in monitoring H₂S in the environment and for work-related safety.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

. This article presents, for the first time, the kinetics and the general features of a photopolymerization system (under visible light) G1/ Iodonium/ TEA/gold chloride (or A/B/N/G), having initial concentrations of A0, B0, N0 and G0, based on the proposed mechanism of Tar et al. Analytic formulas are developed to explore the new features including: (i) both FRP efficacy and the production of nanogold (NG) are proportional to the relative concentration ratios of (A0+B0+N0)/G0, which may be optimized for maximum efficacy; (ii) the two competing procedure of NG production and efficacy of free radical photopolymerization (FRP) can be tailored for optimal system with nanogold in the polymer matrix;(ii) the FRP efficacy is contributed by 3 components: the coupling of the excited state of copper complex (T) with the radicals (R and S) produced by the iodonium and the amine; (iii) the production of NG is contributed by 2 components: the coupling of T and radical (S) with gold ion; (iv) NG production has a transient state value which is an increasing function of light intensity and the combined concentration ratio [(A0/G0)+(N0/(K'M0). whereas it has a steady-state independent to the light intensity.

Sinulariolide, a natural product extracted from cultured-type soft coral Sinularia flexibilis, possesses bioactivity against the movement of several types of cancer cell. However, the molecular pathway of its effects on human bladder cancer remain poorly understood. Using a human bladder cancer cell line as an in vitro model, this study investigated the underlying mechanism of sinulariolide against cell migration/invasion in TSGH-8301 cells. We found that sinulariolide inhibited TSGH-8301 cell migration/invasion, and the effect was concentration-dependent. Furthermore, the protein expressions of matrix metalloproteinases (MMPs) MMP-2 and MMP-9, as well as urokinase, were significantly decreased after 24-h sinulariolide treatment. Meanwhile, the increased expressions of tissue inhibitors of metalloproteinases (TIMPs) TIMP-1 and TIMP-2 were in parallel with an increased concentration of sinulariolide. Finally, the expressions of several key phosphorylated proteins in the mTOR signaling pathway were also downregulated by sinulariolide treatment. Our results demonstrated that sinulariolide has significant effects against TSGH-8301 cell migration/invasion, and its effects were associated with decreased levels of MMP-2/-9 and urokinase expression, as well as increased TIMP-1/TIMP-2 expression. The inhibitory effects were mediated by reducing phosphorylation proteins of the PI3K, AKT and mTOR signaling pathway. The findings suggested that sinulariolide is a good candidate for advanced investigation with the aim of developing a new drug for the treatment of human bladder cancer.

Cachexia is a syndrome characterized by an ongoing loss of skeletal muscle mass associated with poor patient prognosis in non-small cell lung cancer (NSCLC). However, prognostic cachexia biomarkers in NSCLC are unknown. Here, we analyzed computed tomography (CT) images and tumor transcriptome data to identify potentially secreted cachexia biomarkers (PSCB) in NSCLC patients with low-muscularity. We integrated radiomics features (pectoralis muscle, sternum, and T10 vertebra) from CT of 89 NSCLC patients, which allowed us to identify an index for screening muscularity. Next, a tumor transcriptomic-based secretome analysis from these patients (discovery set) was evaluated to identify potential cachexia biomarkers in patients with low-muscularity. The prognostic value of these biomarkers for predicting recurrence and survival outcome was confirmed using expression data from eight lung cancer datasets (validation set). Finally, C2C12 myoblasts differentiated into myotubes were used to evaluate the ability of the selected biomarker, IL-8, in inducing muscle cell atrophy. We identified 75 over-expressed transcripts in patients with low-muscularity, which included IL6, CSF3, and IL8. Also, we identified NCAM1, CNTN1, SCG2, CADM1, IL8, NPTX1, and APOD as PSCB in the tumor secretome. These PSCB were capable of distinguishing worse and better prognosis (recurrence and survival) in NSCLC patients. IL8 was confirmed as a predictor of worse prognosis in all validation sets. In vitro assays revealed that IL-8 promoted C2C12 myotube atrophy. Tumors from low-muscularity patients presented a set of upregulated genes encoding for secreted proteins, including pro-inflammatory cytokines that predict worse overall survival in NSCLC. Among these up-regulated genes, IL8 expression in NSCLC tissues was associated with worse prognosis and the recombinant IL-8 was capable of triggering atrophy in C2C12 myotubes.

: In the realm of data management, data preservation stands as a critical undertaking aimed at preserving and upholding the integrity of data. Regardless of whether it concerns personal or enterprise data, the detrimental effects of malicious alterations implemented by attackers cannot be overlooked. Particularly in conventional industrial control environments, the prevalent practice involves the transmission of data from sensors to databases for storage purposes. However, it is essential to recognize that this process exposes the data to various vulnerabilities. Thus, to ensure the long-term security and reliability of the data, it becomes imperative to implement robust data preservation strategies within these industrial control systems. However, the reliance of these databases on physical hard disks introduces inherent vulnerabilities, including the potential for data loss due to disk damage or targeted malicious attacks. Consequently, it becomes imperative to prioritize the implementation of robust data preservation measures. These measures are crucial in mitigating the risk of disruptions and protecting critical data from compromise. By establishing effective data backup systems, employing advanced security protocols, and implementing proactive monitoring mechanisms, organizations can bolster their data preservation capabilities and safeguard against potential threats to data integrity and availability. As a result, many enterprises opt to store their data with third-party providers to ensure data integrity. However, this approach carries inherent risks. If the third-party service experiences an attack or if the data is tampered with, it becomes challenging to verify the integrity of the data. To address these concerns and ensure data preservation within the context of the Internet of Things (IoT), a growing number of individuals are integrating IoT with Distributed Ledger Technology (DLT). By leveraging DLT, the integrity of data can be ensured, reducing reliance on centralized third-party storage and enhancing security in the IoT ecosystem. In this article, IOTA is the DLT, which employs Directed Acyclic Graph (DAG) to store transaction information. Compared to Ethereum or other blockchain technologies, IOTA offers notable advantages in terms of transaction verification speed, making it highly suitable for real-time IoT environments. However, the conventional transmission path from sensors to IOTA nodes entails a complex route, involving multiple hardware devices before reaching the intended destination. This complexity poses challenges in ensuring data integrity during transmission and introduces vulnerabilities such as man-in-the-middle attacks or SQL injection attacks. To address these issues, we propose a method to streamline the transmission path between sensors and IOTA, specifically tailored for industrial fields with numerous IoT devices. Our approach involves preprocessing the data stored on the server using our method before uploading, ensuring data confidentiality, and leveraging IOTA to guarantee data integrity. To achieve the shortest path between IoT and DLT nodes, it becomes necessary to establish IOTA nodes on lower-level devices, such as Raspberry Pi or IoT controllers. By simplifying the transmission path, we can reduce the potential for tampering and enhance overall data security. Implementing our proposed method enables the assurance of data confidentiality and integrity during both transmission and storage on the server, strengthening the trustworthiness of the IoT, and IOTA integration.

This study aims to implement a SSDBI (single-stage differential boost inverter, SSDBI) applying in a single-stage BESS (battery energy storage system, BESS) topology, which can supply power from lower voltage battery module to AC load. Compared with the common two-stage topology, which has a two-stage converter and higher voltage battery module array, the single-stage topology can reduce the number of cells and components, and improve the power density. In addition, a modified SPWM control was proposed to reduce the control complexity of the SSDBI while improving the THD of the inverter. The modified SPWM control can reduce the duty ratio of the SSDBI and the stress on the components to improve the AC voltage output waveform and reduce the THD value about 2.654%.

This article provides a thorough overview of biomarkers, pathophysiology, and molecular pathways involved in the transition from acute kidney injury (AKI), acute kidney disease (AKD) to chronic kidney disease (CKD). It categorizes the biomarkers of AKI into stress, damage, and functional markers, highlighting their importance in early detection, prognosis, and clinical application. The pathophysiological mechanisms underlying AKI, AKD, including renal hypoperfusion, sepsis, nephrotoxicity, and immune responses, with the impact on renal injury. In addition, various molecules play pivotal roles in inflammation and hypoxia, triggering maladaptive repair, mitochondrial dysfunction, immune system reactions, and cellular senescence of renal cell. Key signaling pathways, such as Wnt/β-Catenin, TGF-β/SMAD, and Hippo/YAP/TAZ, promote fibrosis and impact renal function. The Renin-Angiotensin-Aldosterone System (RAAS) triggers a cascade leading to renal fibrosis, with aldosterone exacerbating oxidative stress and cellular changes that promote fibrosis. Clinical evidence suggests RAS inhibitors may protect against CKD progression, especially post-AKI, though more extensive trials are needed to confirm their full impact.

Information is uploaded and downloaded through the Internet day in and day out ever since we immersed ourselves in the Internet. Data security becomes an area demanding high attention and one of the efficient techniques to protect data is data hiding. Among various data hiding schemes, more applications prefer the schemes with reversibility. In recent reversible data hiding studies, the indices of a codebook can be reordered to hide secret bits. The hiding capacity of the codeword index reordering scheme increases when the size of the codebook gets larger. Since the codewords in the codebook are not modified, the visual performance of compressed images is retained. We propose a novel scheme making use of the fundamental principle of codeword index reordering technique to hide secret data in encrypted images. By observing our experimental results, the embedding capacity is significantly larger. Secret data can be extracted when a receiver owns a data hiding key and image can be recovered when a receiver owns an encryption key.

In this study, we used the natural and anthropogenic characteristics of a coastal region to generate risk maps showing vulnerability and potential hazards, and proposed design criteria for coastal defense and land use for the various kinds of risks faced. The Yunlin coast: a first-level protection area in mid-west Taiwan, was then used as an example to illustrate the proposed design criteria. The safety of the present coastal defenses and land use of the Yunlin coastal area was assessed, and coastal protection measures for hazard prevention were proposed based on the generated risk map. The results can be informative for future coastal management and the promotion of sustainable development of coastal zones.

Detailed kinetics for a 3-wavelength photopolymerization confinement (PC) system is presented for both numerical solutions and analytic formulas. The dynamic profiles are simulated for oxygen, free radical, and conversion for various situations of: blue-light only, 2-light (red and UV), and 3-light (red, blue, UV). An effective PC requires two conditions: (i) a strong N-inhibition for uncured regime with a low conversion (triggered by the UV-light); and (ii) a weak S-inhibition (oxygen-induced) for high conversion under the blue-light or blue and red-light initiation. Good PC candidates are governed by collective factors of: (i) the double ratio of light-intensity and initiator-concentration, (ii) monomers rate-constant; and (iii) effective absorption constants at specific wavelength and initiators. A new reverse feature for the role of N-inhibition on the blue-conversion is found. Higher oxygen concentration leads to a lower conversion, which could be enhanced by reducing the S-inhibition via a red or blue-light pre-irradiation, having a pre-irradiation time TP=200 s for red-light only, and reduced to 150 s, when both red and blue-light. System under UV-only leads a conversion lower than that of blue-only. However, conversion could be improved by the dual-light (blue and UV), and further enhanced by the pre-irradiation of red-light. The two competing factors, N-inhibition and S-inhibition, could be independently and selectively tailored to achieve: (a) high conversion of blue-light (without UV-light), enhanced by red-light pre-irradiation for minimal S-inhibition; and (b) efficient PC initiated by UV-light produced N-inhibition for reduced confinement thickness and for high print speed.

Energy-efficient microprocessors are essential for a wide range of applications. While near-threshold computing is a promising technique to improve energy efficiency, optimal supply demands from logic core and on-chip memory are conflicting. In this paper, we perform static reliability analysis of 6T SRAM and discover the variance among different sizing configuration and asymmetric minimum voltage requirements between read and write operations. We leverage this asymmetric property in near-threshold processors equipped with voltage boosting capability by proposing an opportunistic dual-supply switching scheme with a write aggregation buffer. Our results show that proposed technique improves energy efficiency by more than 21.45% with approximate 10.19% performance speed-up.

The size of seeds is particularly important for agricultural development, as it is a key trait that determines yield. It is controlled by the coordinated development of the integument, endosperm, and embryo. Large seeds are one of the important ways to improve the ultimate “sink strength” of crops, providing more nutrients for early plant growth and showing certain tolerance to abiotic stresses. There are several pathways for regulating plant seed size, including the HAIKU (IKU) pathway, ubiquitin-proteasome pathway, G (Guanosine triphosphate) protein regulatory pathway, mitogen-activated protein kinase (MAPK) pathway, transcriptional regulators pathway, phytohormone regulatory pathways including auxin, brassinosteroid (BR), gibberellin (GA), jasmonic acid (JA), cytokinin (CK), Abscisic acid (ABA), and MicroRNAs (miRNAs) regulatory pathway. This article summarized the seed size regulatory network and prospected ways to improve yield. We expect to provide valuable reference to researcher in the related field.

Canine atopic dermatitis (CAD) is a common chronic allergic skin disease. In our previous study, we isolated two probiotic strains, Lactococcus cremoris subsp. cremoris MP01 and Lacticaseibacillus paracasei subsp. paracasei MP02, from Mongolian fermented milk. These strains demonstrated potential in alleviating symptoms similar to AD and reducing specific immunoglobulin E (IgE) levels in a mouse model of AD. Building upon this discovery, our current investigation sought to evaluate the therapeutic potential of these probiotics for treating CAD. We conducted an open-label, single-arm clinical trial where dogs diagnosed with AD were administered LCP capsules containing Lc. cremoris subsp. cremoris MP01 and L. paracasei subsp. paracasei MP02 once daily for 60 days. Stool, skin swab, and venous blood specimens were collected at three intervals: before, and after 30 and 60 days of LCP intervention. The skin and fecal microbiomes were analyzed using full-length 16S rRNA sequencing. After 60 days of LCP intervention, notable improvements were observed in skin lesions and scratching behaviors, accompanied by reductions in both the Canine Atopic Dermatitis Extent and Severity Index (CADESI) and the Pruritus Visual Analogue Scale (PVAS) scores. Additionally, LCP intervention resulted in significant reductions in IgE levels and modulation in type 1 T helper (Th1)/ type 2 T helper cells (Th2)-related cytokine secretion. Microbiota analysis unveiled changes in the composition of both skin and gut microbiotas, including reductions in Shigella flexneri on the skin and Romboutsia in the gut. Levels of short-chain fatty acid (SCFA) increased following the 60-days of LCP intervention. These effects were likely mediated by alterations in gut microbiota and the upregulation of SCFA levels, which subsequently reduced the secretion of allergy-related IgE. Collectively, these mechanisms contributed to alleviating CAD symptoms, regulating skin microbiota composition, and reducing the adherence and invasion of environmental microbes and pathogens. Overall, our findings highlight the promising therapeutic potential of the Lc. cremoris subsp. cremoris MP01 and L. paracasei subsp. paracasei MP02 mixture as an effective strategy for managing CAD in dogs.

Enterovirus 71 (EV71) is an etiological agent of hand foot and mouth disease and can also cause neurological complications in young children. However, there are no approved drugs to treat EV71 infections. In this study, we conducted an antiviral drug screening by using a Food and Drug Administration (FDA)-approved drug library. We identified five drugs that showed dose-dependent inhibition of viral replication. Sertraline was further characterized because it exhibited the most potent antiviral activity with the highest selectivity index among the five hits. The antiviral activity of sertraline was noted for other EV serotypes. The drug’s antiviral effect is not likely associated with its approved indications as an antidepressant and its mode-of-action as a selective serotonin reuptake inhibitor. The time-of-addition assay revealed that sertraline inhibited an EV71 infection at the entry stage. We also showed that sertraline partitioned into acidic compartments, such as endolysosomes, to neutralize the low pH levels. In agreement with the findings, the antiviral effect of sertraline could be relieved greatly by exposing virus-infected cells to extracellular low-pH culture media. Together, we have identified an FDA-approved antidepressant with the new indication for the broad-spectrum EV inhibition by blocking viral entry through the alkalization of the endolysosomal route.

The coronavirus disease caused by SARS-CoV-2 (known as COVID 19) is highly contagious and has spread rapidly over 200 countries over last three months. WHO suggested urgent escalation in testing, isolation and contact tracing, as the "backbone" of managing the pandemic. Globally, the detection of SARS-CoV-2 in patients are done by RT-PCR and blood antibody-based testing. In addition to the existing processes, flow-cytometry could be used as a high-throughput and efficient diagnostic method for detection of COVID 19. The suspected COVID 19 samples can be analyzed using ‘Indirect flow cytometry’, with the specific primary antibody and fluorescent tagged secondary antibodies. The fluorescence signal can distinguish the infected v/s non-infected samples. In the present article, we have summarized the applications of Flow virometry to study various viruses and have proposed possible application in the detection of COVID 19.

Cancer immunotherapy targeting immune checkpoints has exhibited promising clinical outcomes in many cancers, but it offers only limited benefits for pancreatic cancer (PC). Cancer stem cells (CSCs), a minor subpopulation of cancer cells, play important roles in tumor initiation, progression, and drug resistance. Accumulating evidence suggests that CSCs employ immunosuppressive effect to evade the immune recognition. However, clinical implications of the associations among CD8+ T cells infiltration, programmed death receptor ligand-1 (PD-L1) expression, and CSCs existence are poorly understood in PC. Immunostaining and quantitative analysis were performed to assess CD8+ T cells infiltration, PD-L1 expression, and their relationship with CD44+/CD133+ CSCs and disease progression in PC. CD8+ T cells infiltration was associated with better survival while PD-L1 expression was correlated with PC recurrence. Both the low CD8+ T cells infiltration/high PD-L1 expression group and the high CD8+ T cells infiltration/high PD-L1 expression group show high levels of CD44+/CD133+ CSCs, but patients with low CD8+ T cells infiltration/high PD-L1 expression had worse survival and higher recurrence risk than those with high CD8+ T cells infiltration/high PD-L1 expression. Moreover, CD8+ T cells infiltration could reduce unfavorable prognostic effect of high co-expression of PD-L1 and CD44/CD133. Our study highlights an interaction among CD8+ T cells infiltration, PD-L1 expression, and CD44+/CD133+ CSCs existence, which contributes to PC progression and immune evasion.

Background: Gastric cancer (GC) is one of the leading malignancy diseases worldwide, especially in Asian. CAST is a potential oncogene in GC carcinogenesis process. The character of macrophage infiltration in GC microenvironment was also unaddressed. Methods: We first applied machine searching in gene candidate evaluation of GC. CAST expression was analyzed via the Human Protein Atlas (HPA) and Gene Expression Profiling Interactive Analysis 2 (GEPIA2) database. Protein-protein interaction (PPI) network was downloaded from STRING. We investigated the impact of CAST on clinical prognosis using Kaplan-Meier plotter. The correlations between CAST and Lgr5 and macrophage infiltration in GC was surveyed via TIMER 2.0. Finally, GeneMANIA was also used to evaluate the possible functional linkage between genes. Results: After machine-assisted searching, CAST expression was found signicant difference in the overall survival of GC patients. STRING revealed CAST related proteomics and transcriptomics associations, mainly about CAPN family. Moreover, CAST significantly impacts the prognosis of GC from other datasets validation. Notably, high CAST expression was correlated with worse overall survival in GC patients (hazard ratio = 1.59; logrank P = 9.4 x 10-8). CAST and Lgr5 expressions were both positively correlated with WNT 2 and WNT 2B. Among GC patients in several datasets, CAST and macrophage infiltration evaluated together showed no obvious trend toward poor clinical overall survival. Conclusion: CAST plays an important role in GC clinical prognosis and is associated with WNT 2/WNT 2B/Lgr5. Our study denmostrated that CAST in GC overall survival is regulated by macrophage infiltration.

Dry eye disease (DED) most commonly caused by evaporative subtypes and mainly induced by meibomian gland dysfunction (MGD). Intense pulsed light (IPL) combined with meibomian gland expression (MGX) is noninvasive treatment for improvement of ocular discomfort symptoms and MGD. In this prospective study between November 2020 and May 2022, the patients met the criteria of both ocular surface disease index (OSDI) ≥13 scores and standardized patient evaluation of eye dryness (SPEED)≥ 8 scores were enrolled in Kaohsiung Veteran General Hospital. Three separate treatment sessions of IPL therapy combined with MGX administered to the lower lids with an interval of 28 days. Further tear film assessment included lipid layer thickness (LLT), tear meniscus height (TMH), non-invasive tear break-up time (NIBUT), meibomian gland loss (MGL) either beforeor after 1st and 3rd IPL therapy combined with MGX. Besides, lissamine green staining and pain scores were also recorded. We totally enrolled 37 patients of 74 eyes. Men accounted for 18.92% (7/37). The mean age was 54.51 ± 11.72 years. The mean OSDI scores were 58.12 ± 22, while the SPEED scores were 17.03 ± 5.98. The mean Schirmer’s test was 3.66 ± 2.43 mm. After three sessions IPL treatment with MGX, the OSDI, SPEED, LLT, TMH, MGL, MGXS and pain scores were significantly improved. For the MGX scores (MGXS) ≤20 group, MGL and lissamine green scores showed significant improvements. For the MGXS >20 group, TMH and dry spot rate revealed statistically improvement. Noninvasive IPL therapy with MGX statistically improved not only dry eye symptoms but also tear film assessments.

A sustainable diet which is healthy and environmental friendly is a climate change mitigation option in addition to being a health promoting diet. However, there is a scarcity of information if the Asian diets are sustainable. Therefore, this study aimed to investigate if the diet of the Malaysian population is healthy and sustainable. This is a cross sectional study using dietary data generated from food frequency questionnaires (FFQ). The carbon footprint data were linked with the food items/ food groups in the FFQ. The nutrients of the participants’ diet were computed and the proportions of those who met the recommended nutrients intake were established. Contribution of carbon footprint for different food groups and total carbon footprint for each participant’s diet were computed and expressed as kgCO₂eq. Comparison of carbon footprint from participants’ diets between age, sex and ethnicity were carried out. A total of 4825 participants were included in the analysis. Majority were Malays (66.4 %), females (84.0%), married (80.0%) and in the age groups of 30s to 40s (68.8%). The mean total energy intake was 2485+1000 kcal/day. Only 40 to 60% of all participants achieved the Malaysia Recommended Nutrient Intake (RNI) for calcium and less than half of the female participants who were aged 50 years and below fulfilled the RNI for iron. The most commonly consumed food groups were vegetables (270g/day), wheat, rice, fruits, sugar, seafood, poultry, legumes, snacks, milk and beef (46g/day). Total carbon footprint from the participants’ diets were 2.96 kgCO₂eq/day, with the highest contributions of carbon footprint from rice, vegetables, beef, sugar, other cereals, poultry, seafood, wheat, milk, fruits, legume and snacks. Subgroups such as males, Malays and younger participants were more likely to consume diets with higher carbon footprint, compared to their counterparts. The participants’ diet was low in carbon footprint and environmentally friendly, however the quality of diet may need to be improved. Education measures should be targeted for all population and specifically for the sub-groups that consumed diets with higher carbon footprint.

Since the outbreak of the COVID-19 pandemic, patients infected with COVID-19 may experience abnormal heart rates, posing potential health risks. This study proposes a non-contact method for measuring heart rate (HR) and heart rate variability (HRV) to effectively reduce the risk of infection and assist healthcare professionals in more accurate diagnosis and treatment. In this study, except for the different image acquisition method, other research processes and methods are similar to the research methods in [15]. The image acquisition method is changed from forehead image to palm image. The new non-contact measurement performance of the proposed method can effectively not only avoid infection concerns but also obtain heart rate and HRV quickly and conveniently, providing higher accuracy for physiological parameters, root mean square error (RMSE), and mean absolute percentage error (MAPE) compared to those in recently published papers.

The paper presents the results of geological interpretation of the set of geophysical data with substantiation of geological-geophysical and structural geological criteria of oil and gas potential of the sedimentary cover deep levels and the upper part of the consolidated basement in the central West Siberian oil and gas basin. Gravity, magnetic and seismic data are used. The character of manifestation of the regional Pai-Khoi–Altai strike-slip zone covering an area up to 200 km wide is shown. The study provides a basis for assuming a spatial genetic relationship between the conditions for localizing hydrocarbon traps and the extensional and strike-slip and thrust structures of the zone that form so-called "flower structures". The substantiated structural geological criteria were applied to solve the problem of pattern recognition with training, highlighting the environments favourable for localization of hydrocarbon fields.

Introduction: The treatment of peritoneal dialysis in end-stage renal disease is increasing in clinical practice. The main purpose of this study was to evaluate the effect of far-infrared radiation therapy on inflammation and the cellular immunity of patients undergoing peritoneal dialysis. Materials and Methods: We recruited 56 patients undergoing peritoneal dialysis, and we included 32 patients from the experimental group and 24 patients from the control group in the final analysis. The experimental evaluation in our study was as follows: (1) We used abdominal computed tomography to measure the diameter and degree of hardening of the abdominal veins and large blood vessels to explore the changes in abdominal blood vessels. (2) The study compared the effects of peritoneal dialysis using albumin, blood urea nitrogen, creatinine, white blood cell, neutrophil-to-lymphocyte ratio, platelet-to-lymphocyte ratio, erythrocyte sedimentation rate, Hs-CRP clearance rate, and HBAlC. (3) We compared the cytokine concentration of blood between the two groups while controlling for GM-CSF, IL-2, IFN-γ, IL-6, IL-18, IL-4, IL-5, IL-13, IL-12p70, TNF-α, and IL-1β. Results and Discussion: (1) There was no significant difference in the abdominal blood vessels of the experimental group relative to the control group according to abdominal CT measured over 6 months. (2) Our study demonstrates the statistically significant effect of FIR therapy on the following parameters: albumin (p = 0.048*), creatinine (p = 0.039*), and Hs-CRP (p < 0.001**) decreased significantly, and glomerular filtration rate (eGFR, p = 0.043*) and glucose (p < 0.001**) increased significantly. Our study found that, in the experimental group, albumin and creatinine decreased significantly due to FIR therapy for 6 months. However, our study also found that, in the experimental group, glucose (p < 0.001**) increased significantly due to FIR therapy for 6 months. Peritoneal dialysis combined with FIR can reduce the side effects of glucose in dialysis buffer, which interferes with peritoneal inflammation and peritoneal mesothelial cell fibrosis. In addition, we also found that, in the experimental group, Hs-CRP (p < 0.001**) decreased significantly due to FIR therapy for 6 months. (3) No statistical significance in the inflammatory cytokines related to FIR therapy differences was observed in our study. IFN-γ (p = 0.124), IL-12p70 (p = 0.093), IL-18 (p = 0.213), and TNF-α (p = 0.254) did not exhibit significant improvements in peritoneal dialysis with FIR treatment over 6 months. IFN-γ and IL-18 in the plasma of patients in the experimental group and the control group were higher in the third month than in the first month. Conclusion: We found that the effect of peritoneal dialysis improved significantly with FIR therapy, and significant improvements in the peritoneal permeability and inflammatory response were observed. end-stage renal disease; peritoneal dialysis; far-infrared therapy (FIR)

Blood glucose (BG) monitoring is an important issue for critically ill patients. Previous studies reported that poor sugar control was associated with increased mortality in admitted patients. However, repeated blood glucose monitoring can be resource-consuming and cause a healthcare burden in clinical practice. In this study, we aimed to develop a personalized machine-learning model to predict dysglycemia based on electrocardiogram (ECG) findings. The study included patients with more than 20 ECG records during single hospital admission in the Medical Information Mart for Intensive Care III database, focusing on the lead II recordings, along with the corresponding blood sugar data. We processed the data and used ECG features from each heartbeat as inputs to develop a one-class support vector machine (SVM) algorithm to predict dysglycemia. The model prediction for dysglycemia using a single heartbeat had an AUC level of 0.92 ± 0.09, with a sensitivity of 0.92 ± 0.10 and specificity of 0.84 ± 0.04. Based on 10 s majority voting, the model prediction for dysglycemia improved to an AUC of 0.97 ± 0.06. In this study, we found that a personalized machine-learning algorithm could accurately detect dysglycemia using a single-lead ECG.

Background: To prioritize the development of antiviral compounds, it is necessary to compare their relative preclinical activity and clinical efficacy. Methods: We reviewed in vitro, animal model, and clinical studies of candidate anti-coronavirus compounds and placed extracted data in an online relational database. Results: As of July 2020, the Coronavirus Antiviral Research Database (CoV-RDB; covdb.stanford.edu) contained &gt;2,400 cell culture, entry assay and biochemical experiments, 240 animal model studies, and 56 clinical studies from &gt;300 published papers. SARS-CoV-2, SARS-CoV, and MERS-CoV account for approximately 85% of the data. Approximately 75% of experiments involved compounds with a known or likely mechanism of action, including receptor binding inhibitors and monoclonal antibodies (20%); viral protease inhibitors (18%); polymerase inhibitors (9%); interferons (8%); fusion inhibitors (8%); host endosomal trafficking inhibitors (7%); and host protease inhibitors (5%). For 724 compounds with a known or likely mechanism, 95 (13%) are licensed in the US for other indications, 72 (10%) are licensed outside the US or are in human trials, and 557 (77%) are pre-clinical investigational compounds. Conclusion: CoV-RDB facilitates comparisons between different candidate antiviral compounds, thereby helping scientists, clinical investigators, public health officials, and funding agencies prioritize the most promising compounds and repurposed drugs for further development.

The productivity of forests is often considered to be limited by the availability of phosphorus (P). Knowledge of the role of organic and inorganic P in humid subtropical forest soils is lacking. In this study, we used chemical fractionation and 31P nuclear magnetic resonance (NMR) spectroscopy to characterize the form of P and its distribution in undisturbed perhumid Chamaecyparis forest soils. The toposequence of transects was investigated for the humic layer from summit to footslope and lakeshore. The clay layer combined with a placic-like horizon in the subsoil may affect the distribution of soil P because both total P and organic P (Po) contents in all studied soils decreased with soil depth. In addition, Po content was negatively correlated with soil crystalline Fe oxide content, whereas inorganic P (Pi) content was positively correlated with soil crystalline Fe oxide content and slightly increased with soil depth. Thus, Pi may be mostly adsorbed by soil crystalline Fe oxides in the soils. Among all extractable P fractions, the NaOH-Po fraction appeared to be the major component, followed by NaHCO3-Po; the resin-P and HCl-Pi fractions were lowest. In addition, we found no typical trend for Pi and Po contents in soils with topographical change among the three sites. From the 31P-NMR spectra, the dominant Po form in soils from all study sites was monoesters with similar spectra. The 31P-NMR findings were basically consistent with those from chemical extraction. Soil formation processes may be the critical factor affecting the distribution of soil P. High precipitation and year-round high humidity may be important in the differentiation of the P species in this landscape.

An oceanic radar altimeter such as TOPEX/Poseidon (T/P) is typically for observing elevation changes over the open oceans or large inland lakes/rivers, with limited applications over solid earth due to its large footprint and susceptibility to waveform contamination and slope effect. Here we demonstrate that it is possible to construct a long-term time series of glacier elevation change from T/P-series radar altimeters over two flat surfaces near a glacier terminus and an icefield (Sites A and B, with slopes of 2° and 0.8°) in Mt. Tanggula, Tibet, at elevations over 5400 m. We retracked radar waveforms using the subwaveform threshold algorithm, selected quality altimeter data (1/4 of the original) with nearly the same slope and adjusted the original elevations by fitting with a time-varying, 2nd order surface. The glacier elevation changes at the two sites from T/P (1993–2002) show seasonal elevation oscillations with linear rates at about −3 m/year and abnormal seasonal changes around the 1997–98 El Niño. Site A is over a deep valley in southern Tanggula. Its elevation dropped about 30 m over 1993–2002 (from T/P) and the glacier almost disappeared by 2016 (from altimeters and satellite images). Despite the sporadic Jason-2 and Jason-3 altimeter data, we also derived long-term rates of glacier elevation change over 1993–2017. Landsat-derived glacier area and elevation changes near the two sites confirm the rapid glacier thinning from the altimeters. The glacier meltwater near Site A supplied increasing source water to Chibuzhang Co west of Mt. Tanggula, contributing partially to its accelerated rising lake level. The glacier thinning at Site B (icefield) was correlated with the increased discharge of the Tuotuo River in eastern Mt. Tanggula, a source region of the Yangtze River. The successful detection of glacier thinning at the two sites shows that T/P-series altimeters can serve as a virtual station at a flat glacier spot to monitor long-term glacier elevation changes in connection to climate change. This virtual station concept is particularly useful for inaccessible glaciers, but its implementation faces two challenging issues: increasing the volume of quality altimeter data and improving the ranging accuracy over a targeted mountain glacier spot.

Background: Oral squamous cell carcinoma (OSCC), with poor prognosis and high mortality rates, is one of the most diagnosed head and neck cancers. Cancer stem cells (CSCs) - epithelial-to-mesenchymal transition (EMT) loop is increasingly implicated in the therapy-resistance, relapse, and metastasis of OSCC patients. Accumulating evidence indicate that aberrantly expressed CD47 is associated with cell-death evasion, invasion and cancer metastasis; however, the role of CD47 in the modulation of CSCs-like phenotypes, including therapy-resistance and metastasis, with its underlying mechanism in OSCC remains largely underexplored. Methods: This study investigated the CSCs- modulating potential of CD47 in OSCC cell lines SAS, TW2.6, HSC-3 and FaDu using bioinformatics approach, immunoblotting, immunofluorescence staining, migration, invasion, colony and orosphere formation, as well as radiosensitivity assays. Results: We demonstrated that the characteristic ectopic expression of CD47 in OSCC patients was associated with ~ 20% 2-year survival disadvantage (p = 0.01) and positively correlated with the expression of pluripotency factors; while shRNA silencing of CD47 significantly suppressed cell viability and markedly inhibited orosphere formation, resulting in smaller and fewer orospheres, and downregulated CD133, SOX2, OCT4 and c-Myc mRNA and protein expression levels. We also showed that CD47 downregulation attenuates EMT, migration and clonogenicity of OSCC cells, with associated E-cadherin upregulation and suppression of Vimentin, Slug, Snail, and N-cadherin expression. Conclusion: Of therapeutic relevance, combined with radiotherapy, CD47 knockdown enhanced the anti-OSCC effect of radiotherapy. Thus, we demonstrate the therapeutic feasibility of a CD47-mediated anti-CSCs strategy, and suggest a role for CD47 suppression in potentiating the therapeutic efficacy of radiation therapy in OSCC patients.

Cellular oxidation is responsive to external and internal stimulation and is generated via signal molecules in defense mechanisms through networks of cell proliferation, differentiation, intracellular detoxification, bacterial infection, and immune reactions. Oxidative stress is not necessarily harmful per se; it depends on the balance between oxidation and antioxidation cascades, which are induced according to stimuli and can maintain oxygen homeostasis. The reactive oxygen species (ROS) that are generated during influenza virus (IV) infection have critical effects on both the virus and host cells. In this review, we outline the link between viral infection and ROS production, using IV as an example. We introduce the current state of knowledge on the molecular relationship between cellular oxidation mediated by ROS production and various effects of IV infection. We also summarize the potential anti-IV agents that act by targeting oxidative stress.

Background: Osteoarthritis is the most common degenerative joint disease resulting in pain and altered joint function. Objective: We investigated the possible association between serum interleukin-6 and symptoms of knee osteoarthritis with regard to pain, stiffness, physical function, assessed by the Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC). We also examined the connections between serum interleukin-6 and radiographic severity in primary knee osteoarthritis patients. Methods: In this case-control study, fifty primary knee osteoarthritis patients and fifty age and sex matched controls were randomly recruited. Serum interleukin-6 levels were immunoassayed in patients’ and controls’ serum. Patients’ knee pain, stiffness and physical function were assessed by the respective subscales of the WOMAC Index. Standing anteroposterior radiographs of the knee joint were performed and graded with the Kellegren-Lawrence grade. Results: The mean serum IL-6 level was significantly higher in osteoarthritis patients (110.22 ± 46.98pg/ml) than controls (46.04 ± 12.34 pg/ml) (p=0.001). The WOMAC Index in patients ranged from 0 – 95 and the Kellegren-Lawrence score mean was 2.7 ± 0.76. There was a significant correlation between serum IL-6 levels and pain (r=0.595 p=0.001), physical function score (r=0.666, p=0.001)), and the radiographic score (r=0.799, p=0.001). Regression analysis showed that IL-6 level had a greater impact on both the WOMAC Index (p=0.005) and the Kellegren-Lawrence score (p=0.01). Conclusion: Serum IL-6 level is increased in primary knee osteoarthritis patients. Also, serum interlukin-6 is significantly related to osteoarthritis symptoms and radiographic severity.

The 2019-2020 Australian bushfires followed by the COVID-19 pandemic brought the significant mental health implications of working in healthcare to the fore. The importance of appropriate support services to ensure the resilience and recovery of healthcare workers has been highlighted. In response to healthcare staff experiences during the bushfires, the SEED Wellness Program was created in 2020 in the Illawarra Shoalhaven Local Health District, in NSW Australia. SEED used a participatory action methodology to engage and collaborate with healthcare staff teams in workplace-based restorative activities. Guided by Practice Theory, this study aimed to identify and describe SEED wellness practices that supported healthcare staff. Thirty-three healthcare workers participated in focus groups or individual interviews between June 2021 and March 2022. The analysis involved inductive thematic individual and collective exploration of SEED practices, including co-analysis with participants. Eight core practices that supported participants’ wellbeing were identified including responsive and compassionate leading, engaging staff at every stage of the recovery process, creating a sense of connection with others, and collective caring. The study found that workplace wellness initiatives are optimised when place-based and grounded in local knowledge, needs, and resources incorporating a collective and supportive team approach. Moreover, to ensure engagement in, and sustainability of these initiatives, both bottom-up and top-down commitment is required.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Huntington's disease (HD) is a progressive and fatal neurodegenerative disease caused by CAG repeat expansion in the coding region of huntingtin (HTT) protein. The accumulation of mutant HTT (mHTT) contributes to neurotoxicity by causing autophagy defects and oxidative stress that ultimately lead to neuronal death. Interestingly, epidemiologic studies have demonstrated that the prevalence of type-2 diabetes, a metabolic disease mainly caused by defective insulin signaling, is higher in patients with HD than in healthy controls. Although the precise mechanisms of mHTT-mediated toxicity remain unclear, the blockade of brain insulin signaling may initiate or exacerbate mHTT-induced neurodegeneration. In this study, we used an in vitro HD model to investigate whether neuronal insulin signaling is involved in mHTT-mediated neurotoxicity. Our results demonstrated that mHTT overexpression significantly impairs insulin signaling and causes apoptosis in neuronal cells. However, treatment with liraglutide, a GLP-1 analogue, markedly restores insulin sensitivity and enhances cell viability. This neuroprotective effect may be attributed to the contribution of the upregulated expression of genes associated with endogenous antioxidant pathways to oxidative stress reduction. In addition, liraglutide stimulates autophagy through AMPK activation, which attenuates the accumulation of HTT aggregates within neuronal cells. Our findings collectively suggest that liraglutide can rescue impaired insulin signaling caused by mHTT and that GLP-1 may potentially reduce mHTT-induced neurotoxicity in the pathogenesis of HD.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.