This paper first discusses a fractional-order Liu system of order as low as 2.7 and shows its chaotic characteristics by carrying out numerical simulations such as Lyapunov exponents, bifurcation diagrams and phase portraits. Then, by using the topological horseshoe theory and computer-assisted proof, the existence of chaos in the system is verified theoretically. Finally, the fractional-order system is implemented on a Field Programmable Gate Array (FPGA) and the results obtained show that the fractional-order Liu system is indeed chaotic.

The development of using mitochondrial transplantation in medical therapy are currently discussed. According to the endosymbiotic theory, the movement of mitochondria between different cells is possible. Therefore, an idea of transferring the mitochondria purified from the cells with a limited lifespan to shorten the lifespan of immortal cancer cells was generated. Human umbilical vein endothelial cell (HUVEC) is a kind of primary cell with a limited lifespan. In the present study, the mitochondria purified from HUVEC were applied to alter the malignance of B16F10 melanoma cell. In the comparison of the basic function of mitochondria, HUVEC mitochondria exhibited a higher mitochondrial membrane potential (MMP), while the lower levels in ATP, mitochondrial DNA (mt-DNA) and mitochondrial protein (mt-protein) as compared to melanoma B16F10. After transplanted the B16F10 with HUVEC mitochondria, the migration, invasion, and the proteins involved in cancer stemness were decreased, however, the proteins involved in cell proliferation, such as cyclin D1 and cyclin E1 were increased. In addition, the levels of ATP, mt-DNA and mt-protein of B16F10 were also reduced. As for the dynamics of mitochondria, the reduced expressions of DRP1 and LC3 II revealed that transferred mitochondria can attenuate the mitophagy of B16F10. In mice, inoculated the B16F10 carrying the transplanted HUVEC mitochondria resulted in the larger size of tumor, which is corresponded to the higher levels of cyclin D1 and E1. Interestingly, the lower expressions of N-cadherin, α-SMA and MMP-9 reveled the tumor were decreased in mesenchymal characteristics. Therefore, despite the HUVEC mitochondria did not inhibit the proliferation of B16F10, the metastatic characteristic was reduced.

The kinetics and efficacy profiles of photoinitiated polymerization are theoretically presented. For the same dose, lower light intensity achieves a higher steady-state-efficacy (SSE) in type-I; in contrast, type-II has an equal SSE. Higher light intensity has a faster rising efficacy, due to faster depletion of photoinitiator (PS) concentration. However, type-II process is also affected by the available oxygen. Higher light intensity produces more efficient singlet oxygen, resulting a higher transient efficacy, in which all intensities reach the same SSE when oxygen is completely depleted. With external oxygen, type-II efficacy increases with time, otherwise, it is governed only by the light dose, i.e., same dose achieves same efficacy. Moreover, type-II has an efficacy follows Bunsen Roscoe law (BRL), whereas type-I follows non-BRL. The measured type-I efficacy and gelation profile are analyzed by our analytic formulas. Schematics of the photocrosslinking stage defined by the availability of oxygen is developed, where both type-I and –II coexist until the oxygen is depleted. The overall efficacy may be enhanced by resupply of PS or oxygen during the light exposure. The roles of light dose and PS concentration on the efficacy of photoinitiated polymerization should be are governed a new concept of a volume efficacy (Ve), defined by the product of the crosslink (or gelation) depth (CD) and local [efficacy].

Optimal conditions for maximum efficacy of photoinitiated polymerization are theoretically presented. Analytic formulas are shown for the crosslink time, crosslink depth and efficacy function. The roles of photoinitiator (PI) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented. For optimal efficacy, a strategy via controlled PI concentration is proposed, where re-supply of PI in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced. Experimental data are analyzed for the role of PI concentration and light intensity on the gelation time and efficacy.

The kinetics and modeling of dual-wavelength controlled photopolymerization confinement (PC) are presented and measured data are analyzed by analytic formulas and numerical data. The UV-light initiated inhibition effect is strongly monomer-dependent and different monomers have different C=C bond rate constants and conversion efficacy. Without the UV-light, for a given blue-light intensity, higher initiator concentration (C₁₀) and rate constant (k’) lead to higher conversion, as also predicted by analytic formulas, in which the total conversion rate (R_T) is an increasing function of k’R, which is proportional to k[gB₁C₁]^0.5. However, the coupling factor b₁ plays a different role that higher b₁ leads to higher conversion only in the transient regime; whereas higher b₁ leads lower steady-state conversion. For a fixed initiator concentration C₁₀, higher inhibitor concentration (C₂₀) leads to lower conversion due to stronger inhibition effect. However, same conversion reduction was found for the same H-factor of H₀ = [b₁C₁₀ - b₂C₂₀]. Conversion of blue-only are much higher than that of UV-only and UV-blue combined, in which high C₂₀ results a strong reduction of blue-only-conversion, such that the UV-light serves as the turn-off (trigger) mechanism for the purpose of spatial confirmation within the overlap area of UV and blue light. For example, UV-light controlled methacrylate conversion of a glycidyl dimethacrylate resin formulated with a tertiary amine co-initiator, and butyl nitrite, subject to a continuous exposure of a blue light, but an on-off exposure of a UV-light. Finally, we developed a theoretical new finding for the criterion of a good material/candidate governed by a double ratio of light-intensity and concentration, [I₂₀C₂₀.]/[I₁₀C₁₀].

Single particle analysis with cryogenic electron microscopy (cryo-EM) can determine high resolution structures of macromolecular assemblies. To reconstruct final three-dimension(3D) density map, a reliable initial model is essential and ab-initio reconstruction usually can avoid model bias. The grand challenge for ab-initio reconstruction is to alignment two-dimension(2D) low signal-to-noise ratio(SNR) of particle images with random and unknown parameters. Here we formulate a fast ab initio reconstruction method(named AlignFM) based on Fourier Mellin transform and particle-swarm intelligence optimization(PSO) algorithm. It enables simultaneous 2D alignment and 3D refinement, which can fast generate a reliable 3D map. After experiments on several real datasets. AlignFM shows high performance on fast ab initio reconstruction with a small amount of data.

The endothelium is a monolayer of cells lining the inner blood vessels. Endothelial cells (ECs) play indispensable roles in angiogenesis, homeostasis, and immune response under normal physiological conditions, and their dysfunction is closely associated with pathologies such as cardiovascular diseases. Abnormal EC metabolism, especially fatty acid (FA) dysfunctional metabolism, contributes to the development of many diseases including pulmonary hypertension (PH). In this review, we focus on discussing the latest advances in FA metabolism in ECs under normal and pathological conditions with an emphasis on PH. We also highlight areas of research that warrant further investigation.

Aim: Aging is companied by deteriorations of insulin resistance (IR) and insulin secretion. However, little is known about the roles of aging on different phases of insulin secretion (ISEC); i.e., the first- and second-phase of insulin secretion (FPIS, SPIS) and glucose effectiveness (GE). Methods: Totally 169 individuals (43 men and 126 women) with the similar fasting plasma glucose (FPG: 90 mg/dL) and BMI (men: 23 kg/m2, women 22 kg/m2) were enrolled. IR, FPIS, SPIS, and GE were estimated using our previously developed equations shown below. Pearson correlation analysis was conducted to assess the correlations between age and four diabetes factors (DFs: IR, FPIS, SPIS and GE). The equations that are used to calculate the DF in the present study were built and published by our group. Results: The age of the participants ranged from 18- to 78-year-old. Men had higher FPIS but lower HDL-C levels than women (2.067±0.159, 1.950±0.186 μU/min and 1.130±0.306, 1.348±0.357 mmol/dl, accordingly). The results of Pearson correlation revealed that age was negatively related to IR and GE in both genders (IR: r = -0.39, p < 0.001 for men, r = -0.24, p < 0.003 for women; GE: r = 0.66, p < 0.001 for men, r = 0.78, p < 0.001 for women). In the meanwhile, FPIS was also only found to be negatively correlated with age in female (r = -0.238, p = 0.003). But there was no different with SPIS and age in both of genders. Conclusions: We have found that in Chinese with normal FPG level (90 mg/dl) and body mass index (men: 23 kg/m2, women: 22: kg/m2), age is negatively related to IR and GE in both genders. At the same time, only FPIS was found to be negatively related to age in women. The tightness of their relationships, from the highest to the lowest are, GE, FPIS and IR accordingly. The importance of GE should be re-evaluated. These results should be interpreted with caution because of the small sample size.

The outbreak of recently identified 2019 novel coronavirus (2019-nCOV) infection has become a world-wide health threat. Currently, more information is needed for further understanding the transmission, clinical characteristics, and infection control procedures of 2019-nCOV. Recently, the role of the eye in transmitting 2019-nCOV has been intensively discussed. Previous investigations about other high infectious human COVs, that is, severe acute respiratory syndrome coronavirus (SARS-CoV) and the Middle East respiratory syndrome coronavirus (MERS-CoV), may provide helpful information. In this review, we describe the genomics and morphology of human CoVs, the epidemiology, systemic and ophthalmic manifestations, mechanisms of human CoVs infection, and infection control procedures. The role of the eye in the transmission of SARS-CoV and 2019-nCOV is discussed. Although the conjunctiva is directly exposed to extraocular pathogens, and the mucosa of ocular surface and upper respiratory tract is connected by nasolacrimal duct and share same entry receptors for some respiratory viruses. The eye is rarely involved in human CoVs infection, conjunctivitis is quite rare in patients with SARS-CoV and 2019-nCoV infection, and COV RNA positive rate by RT-PCR test in tears and conjunctival secretions from patients with SARS-CoV and 2019-nCoV infection is also very low, which imply that the eye is neither a preferred organ of human COVs infection, nor is a preferred gateway of entry for human COVs to infect respiratory tract. However, pathogens exposed to the ocular surface might be transported to nasal and nasopharyngeal mucosa by constant tear rinsing through lacrimal duct, and then cause respiratory tract infection. Considering close doctor-patient contact is quite common in ophthalmic practice which are apt to transmit human COVs by droplets and fomites, hand hygiene and personal protection are still highly recommended for health care workers to avoid hospital-related viral transmission during ophthalmic practice.

The main objective of this study is to develop a Hapke photometric model that is suited for Chang’E-1 (CE-1) Interference Imaging Spectrometer (IIM) data. We first divided the moon into three areas including ‘maria’, ‘new highland’ and old ‘highland’ with similar photometry characteristic based on the Hapke parameters of the moon derived from Lunar Reconnaissance Orbiter Camera (LROC) Wide Angle Camera (WAC) multispectral data. Then, we selected the sample data in the ‘maria’ area and obtained a new set of Hapke model’s parameters that can best fit these data. Result shows that photometric correction using Hapke model with these new derived parameters can eliminate the effect of variations in viewing and luminating geometry, especially ‘opposition surge’, more efficiently than the empirical model. The corrected mosaic shows no significant artifacts along the tile boundaries, and more detailed information of the image can be exhibited due to a better correction of ‘opposition surge’ at small phase angle (g <15°).

ST-segment elevation myocardial infarction (STEMI), a major cause of mortality worldwide, has been shown through epidemiological studies to have a relationship with short-term exposure to air pollutants; however, the association between air pollutants and the outcome of STEMI has not been well studied. The aim of this study was to estimate the impact of air pollutants on the outcomes of STEMI. Data on particulate matter <2.5 μm (PM2.5), <10 μm (PM10), nitrogen dioxide (NO2), and ozone (O3) at each of the 11 air monitoring stations in Kaohsiung City were collected between January 1, 2012, and December 31, 2017. Medical records of non-trauma patients aged > 20 years who had visited the ED with a principal diagnosis of STEMI were extracted. The primary outcome measure was in-hospital mortality. After adjusting for potential confounders and meteorological variables, we found that an increase in the interquartile range (IQR) in NO2 was associated with an elevated risk of in-hospital mortality in patients with STEMI. Moreover, during the warm season, an IQR increase in NO2 corresponded to a higher risk of in-hospital mortality in patients with STEMI on lag 3 (OR=3.266; 95% CI:1.203–8.864, p=0.02). Conversely, an IQR increase in PM10 was associated with an increased risk of in-hospital mortality in patients with STEMI on lag 3 (OR=2.792; 95%CI:1.115–6.993, p=0.028) during the cold season. Our study suggests that exposure to NO2 (during warm season) and PM10 (during cold season) may contribute to a higher risk of poor prognosis in patients with STEMI.

Abstract: The Micro-Electro-Mechanical System (MEMS) LiDAR point cloud in autonomous vehicles has a large deflection range, which results in slow registration speed and poor applicability. To maximize speed, an improved NDT (Normal Distribution Transform) method that integrates point cloud density features has been proposed. First, the point cloud is reduced using a modified voxel filter and a pass-through filter. Next, the ISS (Intrinsic Shape Signature) algorithm is utilized to analyze the point cloud features and extract keypoints, the 4PCS (4-Point Congruent Sets) algorithm is then employed to calculate the initial pose under the constraints of the keypoint set to complete the coarse registration. Finally, the self-adaptive segmentation model is constructed by using KD-tree to obtain the density features of keypoints, and the NDT algorithm is combined with this model to form an SSM-NDT algorithm, which is used for fine registration. Each algorithm was compared on the autonomous vehicle dataset PandaSet and actual collected data sets, the results show that the novel method increases the speed by at least 60% and takes into account good registration accuracy and strong anti-interference.

Air quality is one of the most concerning problems in major industrialized cities in the world. Prediction of future air quality is highly relevant to public health. In some big cities, multiple air quality measurement stations are deployed at different locations to monitor air pollutants, such as NO2, CO, PM 2.5 and PM 10, over time. At every monitoring time stamp t, we observe one station×feature matrix xt of the pollutant data, which represents a spatio–temporal process. Traditional methods on prediction of air quality typically use data from one station or can only predict a single pollutant (such as PM 2.5) at a time, which ignores the spatial correlation among different stations. Moreover, the air pollution data are typically highly nonstationary, We propose a de-trending graph convolutional LSTM (long short term memory) to continuously predict the whole station×feature matrix in the next 1 to 48 hours, which not only captures the spatial dependency among multiple stations by replacing an inner product with convolution, but also incorporates the de-trending signals (transform a nonstationary process to a stationary one by differencing the data) into our model. Experiments on the air quality data of the city Chengdu and multiple major cities in China demonstrate the feasibility of our method and show promising results.

Transmembrane protein 100 (TMEM100) plays an important role in angiogenesis, vascular morphogenesis, integrity and cardiovascular development. TMEM100 is a downstream target of the BMP9/10 and BMPR2/ALK1 signaling pathways. Our recent study demonstrates TMEM100 is a lung endothelium enriched gene. Endothelial-specific deletion of Tmem100 impairs lung endothelial cells regeneration. Activation of Tmem100 signaling represents a novel strategy for lung vascular repair and regeneration. It is interesting and important to understand the roles of TMEM100 in the physiological and pathological conditions. In this review, we summarized the current knowledge of TMEM100.

Increasing green total factor productivity is the key to achieving green development in agriculture. This study measured the green total factor productivity of Jiangxi’s agriculture, and its regional and temporal evolution characteristics were examined. The fixed-effects model was then used to investigate the model’s fundamental components empirically. The study’s findings reveal the following: During the period under review, technical change was the primary element driving the rise in the green total factor productivity of agriculture. A rising “U”-shaped trend with notable regional variances characterizes the spatial and temporal evolution. The primary factors that affect changes in green total factor productivity in agriculture include the ease of transportation, the per capita disposable income of rural residents, the level of agricultural mechanization, the degree of urbanization, the level of financial support for agriculture, and the percentage of workers in secondary industries. As a result, it is suggested that, in order to substantially increase agricultural green total factor productivity, agricultural green technological support should be strengthened, more fully developed, and promoted in a multi-pronged approach.

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

Detailed kinetics for a 3-wavelength photopolymerization confinement (PC) system is presented for both numerical solutions and analytic formulas. The dynamic profiles are simulated for oxygen, free radical, and conversion for various situations of: blue-light only, 2-light (red and UV), and 3-light (red, blue, UV). An effective PC requires two conditions: (i) a strong N-inhibition for uncured regime with a low conversion (triggered by the UV-light); and (ii) a weak S-inhibition (oxygen-induced) for high conversion under the blue-light or blue and red-light initiation. Good PC candidates are governed by collective factors of: (i) the double ratio of light-intensity and initiator-concentration, (ii) monomers rate-constant; and (iii) effective absorption constants at specific wavelength and initiators. A new reverse feature for the role of N-inhibition on the blue-conversion is found. Higher oxygen concentration leads to a lower conversion, which could be enhanced by reducing the S-inhibition via a red or blue-light pre-irradiation, having a pre-irradiation time TP=200 s for red-light only, and reduced to 150 s, when both red and blue-light. System under UV-only leads a conversion lower than that of blue-only. However, conversion could be improved by the dual-light (blue and UV), and further enhanced by the pre-irradiation of red-light. The two competing factors, N-inhibition and S-inhibition, could be independently and selectively tailored to achieve: (a) high conversion of blue-light (without UV-light), enhanced by red-light pre-irradiation for minimal S-inhibition; and (b) efficient PC initiated by UV-light produced N-inhibition for reduced confinement thickness and for high print speed.

The performance of the absolute atom gravimeters used on moving platforms, such as vehicles, ships and aircrafts, is strongly affected by the vibration noise. To suppress its influence, we summarize a vibration compensation method utilizing data measured by a classical accelerometer. The measurements with the accelerometer show that the vibration noise in the vehicle can be 2 order of magnitude greater than that in the lab during daytime, and can induce an interferometric phase fluctuation with a standard deviation of 16.70π. With the compensation method, our vehicle-mounted atom gravimeter can work normally in these harsh conditions. Comparing the Allan standard deviations before and after the vibration noise correction, we find a suppression factor of 22.74 can be achieved in static condition with an interrogation time of T = 20 ms, resulting a sensitivity of 1.35 mGal/Hz1/2, and a standard deviation of 0.5 mGal with an average time of 10 s. We also demonstrate the first test of an atom gravimeter in a moving vehicle, in which a suppression factor of 50.85 and a sensitivity of 60.88 mGal/Hz1/2 were realized with T = 5 ms.

Since first described by Dr. Tomisaku Kawasaki in 1967, the clinical diagnosis of Kawasaki disease (KD) has remained relatively unchanged. However, studies since then have suggested that diagnoses using only that original clinical criteria may lead to underdiagnosis. In this review, updated KD diagnostic methods, diagnostic methods for “atypical” KD, diagnostic pitfalls, and other differential diagnoses are discussed. Peripheral blood eosinophil showed important in distinguishing KD from febrile children. We review herein the current literature regarding new biomarkers, scoring systems, and microRNA panels that may aid in the diagnosis of KD, the importance of eosinophil and treatment updates.

Few studies have paid attention to the industrial lands along the Chinese Grand Canal from a cultural per-spective, but cities along the route like Hangzhou have relied on the Canal system to promote industrializa-tion over the past hundred years, and relocated, transformed, or demolished the factories to construct cul-tural space or products mostly after industrial recession at the beginning of 21st century. To deeply analyze this process is quite helpful to understand the typical cultural change and its gain and loss along the Canal especially after cultural and creative industries have been established as the pillar industries of China's na-tional economy. Therefore, along the Hangzhou section of the Canal, we dynamically monitored the land use of the selected 10 industrial lands, with the analysis of high-resolution satellite imageries and the in-dustrial past, the areas of different uses in 2022 were compared. Meanwhile, along with archival data, fieldwork, and experts’ consultation, we designed a mark sheet with factors and scores to comprehensively assess cultural changes over those lands, and its reasons and influence also have been argued, and the prob-lems and suggestions have been offered. This study can contribute to a better understanding of public poli-cy choices in China regarding cities along the Grand Canal after the industrial decline, and provide new perspectives for cultural research, heritage conservation, and urban planning of canals or waterfront spaces.

Spectacular shifts have been led to by The COVID-19 crisis in consumer behavior. Retailers will have to work hard to meet ever-evolving customer service experience with respect to the ways in which it may be differently affected by offline or online transactions in order to win and stay relevant. We suggest an integrative framework and construct customer service experience hypotheses, based on its antecedents and consequences that will contribute to academic study as well as managerial implications. The hypotheses are tested by a simultaneous equation model employing two data sets of the retail industry's offline and online customers. In this study, 571 samples of these businesses, 319 and 252 respondents from offline and online retail channels, respectively, were collected by means of an online web survey of consumers. The results show that the impact of consequences and antecedents of CSX differs based on the media utilized. The integrative framework of CSX in its online medium is far more effective than its explanatory power offline. The outcomes are reasonably counterintuitive in so far as they demonstrate that while most elements of CSX where a service is selected offline is the same in terms of customer loyalty and value equity, the emotional element related to the service provider is higher when the service is selected offline rather than online. These outcomes indicate that, contrary to popular fears, the online medium enables firms to develop a loyal customer foundation. These findings offer perceptivity into how an online channel could be used to better complement the offline channel, contributing towards new knowledge and understanding on CSX and how it may be utilized for managerial decision-making.

This paper presents an improved droop control strategy for grid-connected inverter power stability and power quality under distorted with consideration of grid fluctuation and inter-harmonics. An instantaneous frequency without PLL and amplitude of capacitor voltage feed-forward control strategy is given to power stability control, meanwhile a grid current feedback control is given by an incomplete derivation with a high-pass filter, so that the harmonics and inter-harmonics current can be suppressed. These approaches can provide both good active and reactive power dynamic response under fluctuation of frequency, and rejection ability against harmonic and inter-harmonic voltage. Based on model of inverter, the proposed control strategies are designed in detail. Simulations and experiments are present to validate the effectiveness of proposed method.

Concrete-filled steel tube (CFST) members have been widely used in the field of civil engineering due to their advanced superior mechanical properties. However, internal defects such as concrete core voids and interface debonding are likely to weaken the load-carrying capacity and stiffness of these members, which affects safety and serviceability of CFST structures. Visualizing the inner defects of concrete core in CFST members have been a critical need in civil engineering construction, a travel time tomography (TTT) is introduced to quantitatively identify and visualize the sizes and positions of CFST members in this paper. Moreover, a parameter analysis is performed to investigate the relationship between TTT imaging qualities and influence factors, e.g. inversion parameters, defect sizes and positions. The effectiveness and accuracy of the TTT algorithm are verified by several numerical examples and the results demonstrate that TTT can identify the sizes and positions of concrete core void defects in CFST members efficiently and several inversion parameters including model weighting matrix and inversion grid size really pose a significant impact on the imaging results of CFST members. In addition, several optimum parameters are recommended to benefit the future study of the promising TTT approach for CFST members.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

A case-crossover study examined how PM_2.5 from Asian Dust Storms (ADS) affects the number of emergency room (ER) admissions for cardiovascular diseases (CVDs) and respiratory diseases (RDs). Our data indicated that PM_2.5 concentration from ADS was highly correlated with ER visits for CVDs and RDs. The odds ratios (OR) increased by 2.92 (95% CI: 1.22-5.08) and 1.86 (95% CI: 1.30-2.91) per increase 10 µg/m³ in PM_2.5 levels, for CVDs and RDs, respectively. A 10 µg/m³ increase in PM_2.5 from ADSs was significantly associated with increase in ER visits for CVDs among those 65 years of age and older (an increase of 2.77 in OR) and for females (an increase of 3.09 in OR). In contrast, PM_2.5 levels had a significant impact on RD ER visits among those under 65 years of age (OR=1.77). The risk of ER visits for CVDs increased on the day when the ADS occurred in Taiwan and the day after (lag 0 and lag 1); the corresponding risk increase for RDs only increased on the fifth day after the ADS (lag 5). In Taiwan’s late winter and spring, the severity of ER visits for CVDs and RDs increases. Environmental protection agencies should employ an early warning system for ADS to reduce high-risk groups’ exposure to PM_2.5.

The interpretation of land use and land cover (LULC) is an important issue in the fields of high-resolution remote sensing (RS) image processing and land resource management. Fully training a new or existing convolutional neural network (CNN) architecture for LULC classification requires a large amount of remote sensing images. Thus, fine-tuning a pre-trained CNN for LULC detection is required. To improve the classification accuracy for high resolution remote sensing images, it is necessary to use another feature descriptor and to adopt a classifier for post-processing. A fully connected conditional random fields (FC-CRF), to use the fine-tuned CNN layers, spectral features, and fully connected pairwise potentials, is proposed for image classification of high-resolution remote sensing images. First, an existing CNN model is adopted, and the parameters of CNN are fine-tuned by training datasets. Then, the probabilities of image pixels belong to each class type are calculated. Second, we consider the spectral features and digital surface model (DSM) and combined with a support vector machine (SVM) classifier, the probabilities belong to each LULC class type are determined. Combined with the probabilities achieved by the fine-tuned CNN, new feature descriptors are built. Finally, FC-CRF are introduced to produce the classification results, whereas the unary potentials are achieved by the new feature descriptors and SVM classifier, and the pairwise potentials are achieved by the three-band RS imagery and DSM. Experimental results show that the proposed classification scheme achieves good performance when the total accuracy is about 85%.

Several preclinical and clinical reports have demonstrated that levels of circulating high mobility group box 1 protein (HMGB1) are increased early after trauma and are associated with systemic inflammation and clinical outcomes. However, the mechanisms of the interaction between HMGB1 and inflammatory mediators that lead to the development of remote organ damage after trauma remain obscure. HMGB1 and inflammatory mediators were analyzed in plasma from 54 combat casualties, collected on admission to a military hospital in Iraq, and at 8 and 24 hours after admission. Forty-five (83%) of these patients had traumatic brain injury (TBI). Nine healthy volunteers were enrolled as controls. HMGB1 plasma levels were significantly increased in the first 8 hours after admission, and were found to be associated with systemic inflammatory responses, injury severity score, and presence of TBI. These data provided the rationale for designing experiments in rats subjected to blast injury and hemorrhage, to explore the effect of HMGB1 inhibition by CX-01. Animals were cannulated, then recovered for 5-7 days before blast injury in a shock tube and volume-controlled hemorrhage. Blast injury and hemorrhage induced an early increase in HMGB1 plasma levels that coincided with severity of tissue damage and mortality. CX-01 inhibited systemic HMGB1 release, decreased local and systemic inflammatory responses, significantly reduced tissue and organ damage, and tended to increase survival. These data suggest that CX-01 has potential as an adjuvant treatment for traumatic hemorrhage.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

In this work, we examined the effect of tropospheric emissions on tropospheric ozone (O₃) by conducting three-dimensional (3D) chemistry transport model (CTM) simulations. For the control run, the CTM model simulates tropospheric O₃ levels with a complete set of anthropogenic, biomass burning, and vegetation emissions [8]. For the no-emission simulation, all anthropogenic, biomass burning, and vegetation emissions were turned off. Comparisons of results from these two simulations exhibit the emission impacts on the tropospheric O₃. In the no-emission simulation, distinctive low surface O₃ with concentrations less than 5 ppbv prevail over the Amazon basin, tropical South America, tropical South Africa, Southeast Asia. Transport of air from these land areas downwind contributes to the low O₃ over the remote marine boundary layer. In contrast, elevated O₃ levels over the extra-tropical remote marine boundary layer are less supported by the anthropogenic and biomass burning emissions but more sustained by the downward transport of O₃ from the stratosphere. These results demonstrate that the northern hemisphere continental areas (north of 30^◦N ), polar regions, and tropical continental regions are more sensitive to the tropospheric emissions. The northern hemisphere winter is mostly dominated by the stratospheric processes, while the tropospheric emissions dominate over the southern hemisphere tropical continental areas from tropics to 30^◦S latitudinal bands. The northern hemisphere continental regions are increasingly dominated by tropospheric emissions from spring, to reach maxima in summer, and started to reduce in autumn months.

Growing evidence suggests that healthcare provider advice may increase tobacco cessation, reduce alcohol use, and improve the adoption of desirable lifestyle behaviors among patients. However, how brief interventions and other provider-patient interactions can shape cumulative adoption of multiple modifiable behaviors is less well studied for diabetes prevention and control. Using weighted internet panel survey data from a large socio-demographically diverse urban population in the United States (n=1,003), the present study describes differences in group characteristics among those who had been “ever diagnosed” with prediabetes/diabetes versus those who had not. It also examines the associations between the cumulative adoption of lifestyle behaviors and each of the following: a) lifetime prediabetes/diabetes diagnosis; b) brief lifestyle intervention exposure (i.e., received provider advice/encouragement); and c) recent provider-patient communication about diabetes. There were several group differences in “ever diagnosed” prediabetes/diabetes status by age, employment status, health status, nutrition knowledge, blood pressure/hypertension diagnosis, and diabetes-related health behaviors (p<0.05). Each of the three provider-patient interactions of interest were positively associated with a higher cumulative sum of adopted modifiable lifestyle behaviors for diabetes prevention and management. Results suggest that provider advice/provider-patient interactions of any type can have a salutary impact on whether individuals with prediabetes or type 2 diabetes will engage in recommended lifestyle behavior modifications.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

Zinc is mostly extracted from zinc oxide and sulfide minerals, and this process involves flotation as a key step. While it is easier to float the sulfide mineral, its consumption and depletion has led to an increased reliance on zinc oxide minerals, including smithsonite; hence the development of efficient ways of collecting smithsonite by flotation is an important objective. Herein, we describe the use of 2-(hexadecanoylamino)acetic acid (HAA), a novel surfactant, as a collector during smithsonite flotation. The mechanism and flotation performance of HAA during smithsonite flotation were investigated by total organic carbon (TOC) content studies, zeta potential measurements, FTIR spectroscopy, and XPS analyses, combined with micro-flotation experiments. The flotation results revealed that HAA is an excellent collector in pulp over a wide pH range (9–12) and at a relatively low concentration (2 × 10^‒4 mol/L), at which a recovery of close to 90% of the smithsonite mineral was obtained. TOC-content studies reveal that the good flotation recovery is ascribable to large amounts of collector molecule adsorbed on the smithsonite surface, while zeta potential measurements show that the HAA is chemically adsorbed onto the smithsonite. FTIR and XPS analyses reveal that the HAA-collector molecules adsorb onto the smithsonite surface as zinc-HAA complexes involving carboxylate moieties and Zn sites on the smithsonite surface in alkaline solution.

Understanding how industrial agglomeration affects agricultural green production efficiency is essential for green agricultural development. This study uses the super-efficient EBM-GML to measure and analyze the spatial and temporal evolution characteristics and core sources of dynamics of agricultural green production efficiency in China by using panel data from 30 Chinese provinces from 2006 to 2020. It also empirically investigates the relationships between industrial agglomeration, land transfer, and agricultural production efficiency. By using fixed, intermediary, and threshold effects models, the internal links between the industrial agglomeration, land transfer, and agricultural green production efficiency are examined. The findings indicate that the green production efficiency of Chinese agriculture exhibits the regional characteristics of being “high in the west and low in the east, high in the south and low in the north” in terms of space; in terms of time series, the overall trend is that of growing, with an average annual growth rate of 11.45%, and the growth primarily depends on the “single-track drive” of green technological progress. By promoting land transfer, industrial agglomeration can increase the agricultural green production efficiency and decomposition index. Land transfer has a double-threshold effect on the influence of industrial agglomeration on agricultural green production efficiency. As a result, this study suggests adhering to the idea of synergistic development, promoting agricultural green development, strengthening the development of industrial agglomerations, promoting the quality and efficiency of industry, improving land-transfer mechanisms, and placing a focus on resource efficiency improvements, as well as other policy recommendations.

The deformation monitoring information of concrete dams contains some high-frequency com-ponents, and the high-frequency components are strongly nonlinear, which reduces the accuracy of dam deformation prediction. In order to solve such problems, this paper proposes a concrete dam deformation monitoring model based on empirical mode decomposition (EMD) combined with wavelet threshold noise reduction and sparrow search algorithm (SSA) optimization of long short-term memory network (LSTM). The model uses EMD combined with wavelet threshold to decompose and denoise the measured deformation data. On this basis, the LSTM model based on SSA optimization is used to mine the nonlinear function relationship between the reconstructed monitoring data and various influencing factors. The example analysis shows that the model has good calculation speed, fitting and prediction accuracy and it can effectively mine the date char-acteristics inherent in the measured deformation, and reduce the influence of noise components on the modeling accuracy.

Background: Uncontrolled hemorrhage is a major preventable cause of death in patients with trauma. However, the majority of large animal models of hemorrhage have utilized controlled hemorrhage rather than uncontrolled hemorrhage to investigate the impact of immunopathy and coagulopathy on multi-organ failure (MOF) and mortality. This study evaluates these alterations in a severe porcine-controlled and uncontrolled hemorrhagic shock (HS) model. Methods: Anesthetized female swine underwent controlled hemorrhage (22 ml/kg) and uncontrolled hemorrhage by partial splenic resection followed with or without lactated Ringer solution (LR) or Voluven® resuscitation. Blood chemistry, physiologic variables, systemic and tissue levels of complement proteins and cytokines, coagulation parameters, organ function, and damage were recorded and assessed. Results: HS resulted in systemic and local complement activation, cytokine release, metabolic acidosis, hyperkalemia, MOF, and no animal survival. Resuscitation with LR and Voluven® after HS improved hemodynamic parameters (MAP and SI), metabolic acidosis, hyperkalemia, and survival but resulted in increased complement activation and worse coagulopathy. Compared with the LR group, the HS animal treated with Voluven® had worse dilutional anemia, coagulopathy, renal and hepatic dysfunction, increased myocardial complement activation and renal damage, and decreased survival rate. Conclusions: Hemorrhagic shock triggers early immunopathy and coagulopathy that appear associated with MOF and death. This study indicates that immunopathy and coagulopathy are therapeutic targets that may be addressed with a high-impact adjunctive treatment to conventional resuscitation.

COPD is currently the fourth leading cause of death in the world. Globally, due to continued exposure to COPD risk factors and an aging population, the burden of COPD is expected to increase in the coming decades. The BODE (body mass index, airflow obstruction, dyspnea, and exercise capacity) index is a practical and multidimensional predictor for prognosis of COPD, and better than FEV1.We used the database of Kaohsiung Chang Gung Memorial Hospital medical center, Taiwan to analyze the correlation between BODE index, healthcare resource utilization, and Charlson comorbidity index (CCI). This retrospective study to collect COPD patients with complete BODE index data who had undergone a 6-minute walk examination in our hospital from January 2015 to December 2016. The medical cost and comorbidities database were analyzed from January 1, 2015, to August 31, 2017. Of 396 patients, 382 (96.5%) were male, with an average age of 71.3 ± 8.4 years. There was a significant association between the BODE index and the CCI of COPD patients (p < 0.001). Healthcare resource utilization was positively correlated with the BODE index during the 32 months of retrospective clinical outcomes: positively correlated with the number of hospitalizations (p<0.001), hospitalization days (p<0.001), hospitalization expenses (p=0.005), and total medical expenses (p=0.024), respectively. Our findings provide the crucial information for clinician to predict medical burden and comorbidities in patients with COPD by using BODE index.

Blockchain technology can achieve decentralization, multi-party verification, anti-tampering, anonymity, traceability of transactions, and the application of distributed ledger. Countries around the world continue to seek the blockchain business models, technologies and applications, and have different visions and policies for the development of blockchain. This study conducts a comparative policy framework of theoretical analysis of the blockchain technology between the USA and China. Using the innovative policy tools proposed by Rothwell and Zegveld, the above mentioned governments are analyzed from the viewpoint of twelve policy tools. The results show that the USA and China all prefer to use “Environmental-side” policy. The USA has paid more attention to “Legal and regulatory”, “Public services” and “Procurement”. China has the highest proportion of policies in “Political tools”, followed by “Legal & regulatory”, while “Scientific and technical”, “Education” and “Overseas agent” come in third . The blockchain technology has developed vigorously among industries and its applications have gradually diversified. The results are provided to various stakeholders as a reference for policy planning.

The synergistic features of a three-component, photoinitiating system (A/B/C) based on the measured data and proposed mechanism of Liu et al. are analyzed. The co-initiators/additives B and C have dual-functions of : (i) regeneration of photoinitiator A, and (ii) generation of extra radicals for enhanced conversion efficacy (CE). The synergistic effects led to higher CE for both free radical polymerization (FRP) and cationic polymerization (CP). The CE of FRP has 3 terms due to the direct (tyep-I) coupling of the triplet state of A with the monomer (M) and the coupling of the two radicals, R and R', with M. The CE of CP has a transient state proportional to the effective absorption constant (b), the light intensity (I) and initiator concentration (A0), but a steady state is independent of the light intensity (I). For the CE of FRP, the contribution from radical R had two cases: (i) linear dependence on T=bIA0, or (ii) nonlinear square root dependence T0.5. The synergistic effects led to higher conversion of FRP and CP, consistent with the measured results. The theoretically predicted new features include: (i) co-initiator [C] which always enhances both FRP and CP conversions, and (ii) co-initiator [B] which leads to more efficient FRP, but it also reduces CP.

Degraded soils causing from natural and human affects are universal in arid and semi-arid regions all over the world. Bentonite and humic acid (BHA) are increasingly being tested to remediate these degraded lands with potential benefits on crop production and soil health. The objective of this paper was to determine the residual effects four to five years after a one-time BHA application at six rates on (i) dynamic changes in soil properties, and (ii) oat crop productivity parameters, in a dryland farming ecosystem. With increasing rates of one-time BHA application, soil profile water storage displayed a piecewise linear increase plus plateau, whereas soil electrical conductivity, pH and bulk density were all reduced significantly (P < 0.05) in the 0-20 cm and 20-60 cm layers. The improved soil environments gave rise to an increased activity of soil enzymes urease, invertase and catalase that respectively reached the peak values of 97%, 37% and 32% at the rates of 21 to 24 Mg BHA ha-1. These conversely boosted soil nutrient turnover, leading to a 40% higher soil available P. Compared with the control treatment, application of BHA at the estimated optimum rate (roughly 24 Mg ha-1) increased grain yield by 20%, protein yield by 62%, water use efficiency by 41%, and partial factor productivity of N by 20%. Results of this study showed for the first time that a one-time BHA application would be a new and effective strategy to combat land degradation, drought, and promote a sustainable soil micro-ecological environment in dryland agroecosystem under a varying climate scenario.

This paper presents a novel approach for semantic segmentation of building roof in dense urban environment with Deep Convolution Neural Network (DCNN) using imagery acquired by a Chinese Very High Resolution (VHR) satellite mission, i.e. GaoFen-2 (GF-2). To provide an operational end-to-end work flow for accurate build roof mapping with feature extraction as well as image segmentation, a fully convolutional DCNN with both convolutional and deconvolutional layers is designed to perform the VHR image analysis for labeling pixels. Since the diverse urban patterns and building styles in large areas, sample image data sets of building roof and non-building roof are collected over different metropolitan regions in China. We selected typical cities with dense urban environment in each metropolitan region as study areas for collecting training and test samples. High performance cluster with GPU-mounted workstations is employed to perform the model training and optimization. With the building roof samples collected over different cities, the predictive model with multiple NN layers is developed for building roof labeling. The validation of the building roof map shows that the overall accuracy(OA) and the mean Intersection Over Union( mIOU) of DCNN based segmentation are 94.67%, 0.85 respectively, while CRF-refined segmentation achieved OA of 94.69% and mIOU of 0.83. The results suggest that the proposed approach is a promising solution for building roof mapping with VHR images over large areas across different urban and building patterns. With the operational acquisition of GF2 VHR imagery, it is expected to develop an automated pipeline for operational built-up area monitoring and timely update of building roof map over large areas.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Autonomous target recognition (ATR) plays a crucial role in maintaining situational awareness during environmental monitoring. Unmanned aerial vehicles (UAVs) equipped with autonomous target recognition technology can gather and analyze real-time information about targets, including their locations, sizes, and types. However, UAV-captured images in complex real-world environments often display significant variations in perspective and scale due to changes in UAV altitude and distance. Existing methods for autonomous target recognition on UAVs struggle to capture targets from large field-of-view and multi-scale images, resulting in low recognition accuracy and high false-positive rates. This paper introduces two novel Slimmable neural network models, namely SE-YOLOv5s and ST-YOLOv5s, which are based on the YOLOv5s architecture. These models incorporate the Squeeze and Excitation and Swin-Transformer mechanisms to enhance the ability to extract features from large field-of-view and multi-scale images. To evaluate their performance, experiments were conducted on the Visdrone19 aerial dataset. Compared to the state-of-the-art YOLOv5s algorithm, the utilization of SE-YOLOv5s and ST-YOLOv5s for autonomous target recognition on low-altitude drones resulted in improvements in both accuracy and false-positive rates. These proposed methods combine Slimmable neural network design with feature enhancement mechanisms, addressing the challenges posed by complex real-world environments in UAV missions. The advancements in autonomous target recognition on low-altitude drones will significantly contribute to enhancing situational awareness in future environmental monitoring.

. Manufacturers are increasingly adopting mixed-flow manufacturing models to meet the growing customized, diverse, and dynamic customer demand. In such an environment, material distribution scheduling optimization is vital for smooth operations and is integral to production management. However, manufacturers frequently encounter problems like disordered and delayed material distribution. Traditional scheduling methods suffer from problems like inadequate transparency, delayed decision directives, and suboptimal results, impacting performance. To this end, this study proposes a dynamic material distribution scheduling optimization model and strategy based on digital twin (DT) to address these problems. Firstly, we introduce workstation satisfaction and establish a material distribution path optimization model minimizing total distribution cost while maximizing workstation satisfaction. Subsequently, we present a cloud-edge computing-based decision framework and explain the DT-based material distribution system's components and operation. Furthermore, a dynamic material distribution scheduling optimization mechanism based on DT is designed. By incorporating a savings method and incentive, penalty strategies, improvements are made to the path node selection probabilities and the information pheromone update rules of the traditional ant colony optimization (ACO) algorithm. Finally, a numerical case study, using real data from collaborating enterprises, validates the proposed algorithm and strategy. This research offers valuable insights into logistics management and algorithm design in smart manufacturing environments.

Arc sensors have been used in seam tracking and widely studied since the 80s; commercial arc sensing products for T and V shaped grooves have been developed. However, it is difficult to use these arc sensors in narrow gap welding because arc stability and sensing accuracy are not satisfactory. Pulse gas melting arc welding (P-GMAW) has been successfully applied in narrow gap welding and all position welding processes, so it is worthwhile to research P-GMAW arc sensing technology. In this paper, we derived a linear mathematical P-GMAW model for arc sensing, and the assumptions for the model are verified through experiments and finite element methods. Finally, the linear characteristics of the mathematical model were investigated. In torch height changing experiments, uphill experiments, and groove angle changing experiments the P-GMAW arc signals all satisfied the linear rules. In addition, the faster the welding speed, the higher the arc signal sensitivities; the smaller the groove angle, the greater the arc sensitivities. The arc signal variation rate needs to be modified according to the welding power, groove angles, and swing or rotate speed.

Background: Shorter leukocyte telomere length (LTL) is observed in multiple age-related diseases, which are also associated with vitamin D deficiency (i.e., osteosarcopenia, neurocognitive disorders, cancer, osteoarthritis, etc.), which suggests a close association. In this study, we examined the relationship between vitamin D levels and LTL in older participants of the UK Biobank. Methods: Data were collected from the UK Biobank. Participants aged 60 and older (n=148,321) were included. Baseline LTL was measured using a multiplex qPCR technique and expressed as the ratio of the telomere amplification product (T) to that of a single-copy gene (S) (T/S ratio). Se-rum 25-hydroxyvitamin D (25OHD) was stratified by z score and linked to LTL in a linear regression model adjusting for covariates. Results: Compared to the medium level, a low (in the range of 16.6 nmol/L, 29.7 nmol/L) or extremely low (≤ 16.6 nmol/L) level of serum 25OHD was associated with shorter LTL: 0.018 SD (standardized β= -0.018, 95% CI -0.033 to -0.003, P=0.022) and 0.048 SD (standardized β= -0.048, 95% CI -0.083 to -0.014, P=0.006), respectively. Additionally, the high serum 25OHD groups (> 95.9 nmol/L) had 0.038 SD (standardized β= -0.038, 95% CI -0.072 to -0.004, P=0.030) shorter mean LTL than the group with medium 25OHD levels. The associations above were adjusted for multiple variables. Conclusion: In this population-based study, we identified an inverted U-shape relationship between LTL and vitamin D status. Whether high or low vitamin D-associated shorter LTL is mechanistically related to age-related conditions remains to be elucidated.

Bright morning light (BML) entrains the body clock, modulates circadian rhythm, and improves sleep-wake disturbances. However, its impact on the autonomic nervous system (ANS) at night remains unclear. Hence, we investigated the effects of BML exposure on activities of the parasympathetic nervous system (PSNS) and sympathetic nervous system (SNS) at night. This non-randomized controlled pilot study included participants ≥60 years, diagnosed with a type of dementia or cognitive disorder. We excluded participants with pacemakers. The treatment group received 2500 lx BML, whereas the control group received approximately 200 lx of general lighting. We measured the heart rate variability to quantify ANS activity. The treatment group displayed significantly increased high-frequency (HF) power (Roy's largest root=2.44; P<.01) and insignificantly decreased normalized low-frequency (LF%) power. The corresponding low-frequency/high-frequency ratio (LF/HF), insignificant decrease, and cognitive function were correlated with PSNS activity (Roy's largest root=3.92; P<.01), which is effective for moderate dementia. BML exposure reduced SNS activity and enhanced PSNS activity at night, which consequently affected cognitive function. Furthermore, the light washout intervention markedly increased SNS activity at night. BML therapy may be a useful clinical tool for alleviating the deterioration of cognitive function.

Abnormal connections in brain networks of healthy people always bring the problems of cognitive impairments and degeneration of specific brain circuits, which may finally result in Alzheimer’s disease (AD). Exploring the development of the brain from normal controls (NC) to AD is an essential part of human research. Although connections changes have been found in the development, the connection mechanism that drives these changes remain incompletely understood. The purpose of this study is to explore the connection changes in brain networks in the process from NC to AD, and uncover the underlying connection mechanism that shapes the topologies of AD brain networks. In particular, we propose a model named MINM from the perspective of topology-based mutual information to achieve our aim. MINM concerns the question of estimating the connection probability between two cortical regions with the consideration of both the mutual information of their observed network topologies and their Euclidean distance in anatomical space. In addition, MINM considers establishing and deleting connections, simultaneously, during the networks modeling from the stage of NC to AD. Experiment results show that MINM is sufficient to capture an impressive range of topological properties of real brain networks such as characteristic path length, network efficiency, and transitivity, and it also provides an excellent fit to the real brain networks in degree distribution compared to experiential models. Thus, we anticipate that MINM may explain the connection mechanism for the formation of the brain network organization in AD patients.

This study aims to develop an in-situ field repair approach, special for aircraft composite structures, to enhance the interlaminar toughness of plain woven composites (PWCs) by adding multi-walled carbon nanotubes (MWCNTs). MWCNTs are dispersed at each interface between prepreg layers by means of solvent spraying with the density is 1.58 g/m2. And then, the layers are stacked with the predefined sequence and cured at 120℃ and 1 bar pressure using the heat repairing instrument. Moreover, double cantilever beam (DCB) standard test is used to investigate the interlaminar toughening effect due to the MWCNTs. For comparison, original samples are also prepared, the results indicate that the introduction of MWCNTs can favorably enhance the interlaminar toughness of PWCs at field repair approach and the Mode I fracture energy release rate GIC increases by 102.92%. Based on finite element method (FEM) of continuum damage mechanics, the original and MWCNTs toughening specimen under DCB Mode I fracture are modeled and analyzed. The simulation and experiment are in good agreement. Finally, the toughening mechanism of MWCNTs is explored by scanning electron microscope (SEM), it is founded that a large amount of Fiber-matrix (F-M) interface debonding and matrix cracking of mountain shape are the major modes of fracture accompanied with few fiber breakage and matrix peeling off for the MWCNTs toughening specimens.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Prostate-specific membrane antigen (PSMA) is a well validated prostate cancer marker, but reported PSMA-targeted tracers derived from the Lys-urea-Glu pharmacophore including the clinically validated [99mTc]Tc-EDDA/HYNIC-iPSMA have high off-target uptake in kidneys, spleen and salivary glands. In this study, we synthesized and evaluated three novel 99mTc-labeled PSMA-targeted tracers and investigated if the tracers derived from the Lys-urea-Aad pharmacophore could have minimized uptake in off-target organs/tissues. In vitro competition binding assays showed that compared with HYNIC-iPSMA, the three novel ligands had slightly weaker PSMA binding affinity (average Ki = 3.11 vs 8.96 - 11.6 nM). Imaging and ex vivo biodistribution studies in LNCaP tumor-bearing mice showed that [99mTc]Tc-EDDA/HYNIC-iPSMA and the three novel tracers successfully visualized LNCaP tumor xenografts in SPECT images and were excreted mainly via the renal pathway. The average tumor uptake at 1 h post-injection varied from 5.40 to 18.8 %ID/g, and the tracers derived from the Lys-urea-Aad pharmacophore had much lower uptake in spleen and salivary glands. Compared with the clinical tracer [99mTc]Tc-EDDA/HYNIC-iPSMA, the Lys-urea-Aad derived [99mTc]Tc-EDDA-KL01127 had lower background uptake and superior tumor-to-background contrast ratios, and is therefore promising for clinical translation to detect prostate cancer lesions with SPECT.

Air pollution is related to the development of people's livelihood. As one of the main pollutants in the air, formaldehyde affects people's physical and mental health. In order to remove formaldehyde and better protect the health of residents, it is very necessary to develop efficient adsorption materials. In this study, a cellulose composite aerogel Microcrystalline Cellulose/ N-(2- aminoethyl) -3- aminopropyl methyl dimethoxysilane (MCC/APMDS) modified by APMDS was explored. The pore volume and specific surface area of the modified aerogel decreased, the average pore diameter increased, and the adsorption capacity of formaldehyde was stronger. The adsorption experiment shows that the sample prepared under the conditions of APMDS dosage of 6 wt%, reaction time of 4 h and reaction temperature of 90℃ has the largest average pore size (14.56 nm) and the largest formaldehyde adsorption capacity (9.52 mg/g). The excellent adsorption of the composite aerogel is due to high porosity and rich active amino groups on the surface. This study provides valuable information for the preparation of adsorption materials with high formaldehyde adsorption capacity for air purification.

The centrifugal force field in the hydrocyclone was affected by the concave-wall curvature radius R0, the mechanism of droplet deformation was closely related to the mass transfer efficiency. Numerical simulation and experimental data were collected to reveal the deformation characteristics and mechanism of single droplet crossing concave-wall jet. Normalized interfacial energy γ and stretching performance were provided to investigate the droplet deformation process. The results showed that the droplet was stretched along the streamwise and shrank along the spanwise in the concave-wall jet. The droplet interfacial energy and deformation were the largest when the droplet crossed the jet boundary at t = 0.20 s. Maximum γ value increased with the increase of R0 by 57.3% to 71.4%, and the distance between droplet and concave-wall increased with R0. Q-criterion was exported to show the vortex strength increasing as the decrease of R0 in the jet boundary. The pressure distribution inside the droplet showed that the pressure decreased as R0 increased, while the pressure difference increased along the streamwise and wall-normal direction. The study suggested that the droplet breakup was more difficult for the smaller R0, which was beneficial for liquid-liquid heterogeneous separation.

.(1) Background: Groundwater resources management in dry lands, characterized by climate var-iability and population growth, is difficult. Exploration and exploitation of groundwater, due to inadequate surface water is very costly. The present study employed Analytic Hierarchy Process (AHP) and GIS to identify Ground-Water Potential (GWP) areas in a semi-arid region of Nigeria; (2) Methods: Land-use-land-cover, drainage density, slope, rainfall, static water level, soil media, vadose media and aquifer media were selected for GWP analysis. Parameters weights were de-termined using AHP and ranked based on their contribution to GWP by experts. The parameters were then integrated using weighted overlay tool in ArcGIS 10.5 to produce GWP map of the study area. Boreholes yield data from 245 wells were collected to determine the model accuracy and model validation; (3) Results: Results classified the study area into very high GWP (1.9%), high GWP (8.8%), moderate GWP (62%), low GWP (20.70%) and very low GWP (6.6%). Validation of the AHP model with boreholes yield data shows a correlation coefficient of 71.3% giving a good prediction; (4) Conclusions: AHP and GIS can be used to successfully map GWP areas which could serve as an exploration guide for sustainable management of groundwater resources in semi-arid areas.

Fibroblast activation protein (FAP) is a membrane-tethered serine protease overexpressed in the reactive stromal fibroblasts of &gt; 90% human carcinomas, which makes it a promising target for developing radiopharmaceuticals for imaging and therapy of carcinomas. Here, we synthesized two novel (R)-pyrrolidin-2-yl-boronic acid-based FAP-targeted ligands; SB02055 (DOTA-conjugated (R)-(1-((6-(3-(piperazin-1-yl)propoxy)quinoline-4-carbonyl)glycyl)pyrrolidin-2-yl)boronic acid) and SB04028 (DOTA-conjugated ((R)-1-((6-(3-(piperazin-1-yl)propoxy)quinoline-4-carbonyl)-D-alanyl)pyrrolidin-2-yl)boronic acid). natGa- and 68Ga-complexes of both ligands were evaluated in preclinical studies and compared to previously reported natGa/68Ga-complexed PNT6555. Enzymatic assays showed that FAP binding affinities (IC50) of natGa-SB02055, natGa-SB04028 and natGa-PNT6555 were 0.41±0.06, 13.9±1.29 and 78.1±4.59 nM, respectively. PET imaging and biodistribution studies in HEK293T:hFAP tumor-bearing mice showed that while [68Ga]Ga-SB02055 presented with a nominal tumor uptake (1.08±0.37 %ID/g), [68Ga]Ga-SB04028 demonstrated clear tumor visualization with ~1.5-fold higher tumor uptake (10.1±0.42 %ID/g) compared to [68Ga]Ga-PNT6555 (6.38±0.45 %ID/g). High accumulation in the bladder indicated renal excretion of all three tracers. [68Ga]Ga-SB04028 displayed low background level uptake in most normal organs, and comparable to [68Ga]Ga-PNT6555. However, since its tumor uptake was considerably higher than [68Ga]Ga-PNT6555, the corresponding tumor-to-organ uptake ratios for [68Ga]Ga-SB04028 were also significantly greater than [68Ga]Ga-PNT6555. Our data demonstrate that (R)-(((quinoline-4-carbonyl)-D-alanyl)pyrrolidin-2-yl)boronic acid is a promising pharmacophore for the design of FAP-targeted radiopharmaceuticals for cancer imaging and radioligand therapy.

Globally, weeds interfere with agricultural production activities and have a very serious impact on agriculture and animal husbandry. Identifying a safe and reliable weed control strategy might increase yield, production net income, and improve crop quality. A field experiment was carried out to explore the effects of weeds interference frequency on the yield and quality of Glycyrrhiza uralensis Fisch in an arid and semi-arid area of northwest China. The experiment consisted of seven treatments and were (1) no weeding, marked as WF0; (2)-(7) artificial weeding by hoe once every 1, 2, 4, 6, 8, 10 weeks after emergence, marked as WF1, WF2, WF4, WF6, WF8 and WF10, respectively. We found that the higher weeding frequency had a higher the plant height, photosynthesis, yield and quality. The highest yield was obtained in the WF1 treatment, while the cost of weeding was the highest among all treatments. The concentration of liquiritin and glycyrrhizic acid were increased by 53.24% and 36.57%, with the highest nitrogen metabolism enzymatic activities and quality in WF4 treatment. WF4 treatment exhibited the largest increases in the net income among all treatments in both growing seasons, with respective increases up to 71.39 % and 78.81%. These findings suggested that weeding once every 4 weeks would be an effective and sustainable measure to control weeds in an arid and semi-arid area.

Background and Objectives: The existing recommendations for female pelvic magnetic susceptibility weighted imaging MRI (FP-SWI) have not been optimized to capture the disease characteristics of the female pelvis. Therefore, it is imperative to explore acquisition parameters before conducting larger-scale studies. To establish optimized flip angle (FA) for acquiring FP-SWI to improve the image quality of female pelvic lesion sites. Materials and Methods: To evaluate signal quality and lesion conspicuity, regions of interest (ROIs) were manually drawn within the lesion on SWI sequences. Signal intensity was measured within the ROIs. Additionally, signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) were calculated for SWI sequences acquired at three FA: 10°, 15°, and 20°. Finally, a qualitative assessment of anatomical detail visualization, geometric distortion extent, artifacts, and lesion clarity was performed using a four-point scale. The Wilcoxon rank sum test was employed to compare the qualitative evaluation parameters. The intra-class correlation coefficient (ICC) was calculated to determine the consistency of subjective ratings between two observers. Results: FA=10° showed significantly higher SNR than FA=15° and 20° in most anatomical regions (P&lt;0.05), while the CNR was significantly higher than FA=15° and 20° (P&lt;0.05). Compared with FA=15° and 20°, the image quality of FA=10° was significantly higher, with less distortion and ghosting, and better image contrast (P&lt;0.05). Lesions with FA=10° exhibited higher clarity compared to FA=15° and 20° (P&lt;0.05). Conclusions: The image quality of FP-SWI images at FA=10° exceeds that at FA=15° and 20°. We recommend that when conducting SWI examination of the female pelvic cavity, the FA value should be set at 10° to stabilize the SWI sequence and improve image quality.

Autonomous aerial refueling technology is an effective solution to extend flight duration of unmanned aerial vehicles, and also a great challenge due to its high risk. For autonomous probe-and-drogue refueling tasks, relative navigation to provide relative position between the receiver aircraft and the refueling drogue is the first and essential step, and vision-based method is the most frequently used. A new monocular vision navigation sensor with image processing strategy consisting of the drogue detection method and the tracking method is developed for autonomous aerial refueling in this paper. In the drogue detection method, thresholding and mathematical morphology method are adopted to eliminate image interference, and contours extraction method is applied to obtain all contours, which are then subsequently checked to achieve target contour of drogue. In the tracking method, a rectangle of interest (ROI) of current frame image is determined by positioning results of last frame, and then processed by the previous drogue detection method. Finally, the proposed image processing strategy in monocular vision navigation sensor is validated using real flight images, which are captured from an autonomous aerial refueling testbed using a micro six-rotor aircraft as receiver aircraft.

The root extracts of Symphytum officinale (comfrey) are commonly used in traditional medicine to treat muscle, joint, skin and bone disorders. However, little information is available on the biomedical functions of comfrey leaves. In this study, sequencing results of Internal Transcribed Spacer and trnL-trnF genes showed that plants purchased from the local market were comfrey and named as S. officinale WL (WL). The optimal extraction conditions of WL leave with the highest extract yield and contents of total phenols and flavonoids by microwave-assisted extraction were identified. The antioxidative and anti-inflammatory activities and possible molecular mechanism(s) of the WL leaf extract (WLE) were evaluated. Furthermore, the major component of WLE was identified as rosmarinic acid by HPLC. Results showed that the optimal extract condition was obtained with 750W microwave power, 50℃, 75% methanol, the solid-to-solvent ratio of 1:10, and 15 minutes. Results of all DPPH, ABTS and superoxide radical scavenging activities, reducing power, ferrous ion chelating activity, and ferric reducing antioxidant power showed high antioxidative capacities of WLE. Furthermore, WLE showed obvious DNA protecting activity. WLE attenuated lipopolysaccharides-stimulated inflammation by suppressing iNOS, COX-2, IL-1β, IL-6, and TNF-α expressions in RAW264.7 macrophages. These attenuations involved in inactivations of lipopolysaccharides-induced NF-κB and MAPK signaling pathways.

Cellular oxidation is responsive to external and internal stimulation and is generated via signal molecules in defense mechanisms through networks of cell proliferation, differentiation, intracellular detoxification, bacterial infection, and immune reactions. Oxidative stress is not necessarily harmful per se; it depends on the balance between oxidation and antioxidation cascades, which are induced according to stimuli and can maintain oxygen homeostasis. The reactive oxygen species (ROS) that are generated during influenza virus (IV) infection have critical effects on both the virus and host cells. In this review, we outline the link between viral infection and ROS production, using IV as an example. We introduce the current state of knowledge on the molecular relationship between cellular oxidation mediated by ROS production and various effects of IV infection. We also summarize the potential anti-IV agents that act by targeting oxidative stress.

To investigate the repair mechanism of umbilical cord mesenchymal stem cells (UC-MSCs) in hydrogel on pancreatic β-cells in diabetes, MIN-6 damaged by streptozotocin (STZ) in vitro was used in co-culture with UC-MSCs in hydrogel (UC-MSCs + hydrogel). It was found that UC-MSCs + hydrogel had a significant repair effect on injured MIN-6 cells, which was better than the use of UC-MSCs alone (without hydrogel). After repair, the expression of superoxide dismutase (SOD) and catalase (CAT) as well as the total antioxidant capacity (T-AOC) of the repaired MIN-6 cells were increased, effectively reducing the oxidative stress caused by STZ. In addition, UC-MSCs + hydrogel were able to curb the inflammatory response by promoting the expression of anti-inflammatory factor IL-10 and reducing inflammatory factor IL-1β. In addition, the expression of both nuclear antigen Ki67 for cell proliferation and insulin-related genes such as Pdx1 and MafA was increased in the repaired MIN-6 cells by UC-MSCs + hydrogel, suggesting that the repair effect promotes the proliferation of the injured MIN-6 cells. Compared with the use of UC-MSCs alone, UC-MSCs + hydrogel exhibited longer survival time of UC-MSCs, because the porous structure and hydrophilic properties of the hydrogel could affect the growth of cells and slow down their metabolic activities, resulting in a better repair effect on the injured MIN-6 cells.

This study aimed to investigate the relationship between sleep duration, dementia severity, age, and ANS regulation. This cross-sectional pilot study included 27 older patients with probable Alzheimer’s disease, hospitalized at a psychiatric center. We measured heart rate variability to assess ANS regulation at night, evaluated dementia severity using the Clinical Dementia Rating scale, and obtained sleep duration data from sleep diaries maintained by psychiatric nurses. The data were analyzed using repeated-measures generalized linear models with age, sex, dementia severity, and medication (antipsychotics) as covariates. A sleep duration of 7–8 h per night was associated with better ANS regulation than other sleep durations, as indicated by sympathovagal balance (p = 0.005). ANS dysregulation was characterized by a 20.7% increase in sympathetic nervous system activity and a 14.8% decrease in parasympathetic nervous system (PSNS) activity. We found a significant correlation between dementia severity and PSNS activity (p = 0.04) and observed an inverted U-shaped association between sleep duration and ANS regulation. This pilot study demonstrated that a sleep duration of 7–8 h per night may be critical in maintaining optimal ANS regulation. Bidirectional associations between sleep duration, inadequate sleep duration, aging, and ANS regulation warrant further investigation.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

The aim of this study is to present a method for developing fragility curves for soil liquefaction that are consistent with the seismic hazard using Monte Carlo simulation. This method can account for all the uncertainties and variabilities of the input parameters. The seismic parameters of earthquake magnitude (M) and the associated peak ground acceleration (PGA) are considered together for the liquefaction assessment. The liquefaction potential and damages obtained by this method are more realistic. A case study is performed using data from a sand-boil site in Yuanlin, Changhua county, where liquefaction occurred during the Chi-Chi earthquake in Taiwan in 1999. The results show that the liquefaction potential index, IL, the post-liquefaction settlement, St, and the liquefaction probability index, PW, are all suitable parameters for evaluating the liquefaction damages. The fragility curves for soil liquefaction developed by this method can support the performance-based earthquake engineering (PBEE) approach, provide guidance for liquefaction evaluation to the ‘Taiwan Earthquake Loss Estimation System’-TELES, and serve as a basis for scenario simulation and an earthquake early warning system for liquefaction damages.

The present study analyzed light emitting diodes (LEDs) as an output load and used a Taylor series to describe the characteristic curve based on the exponential characteristic of voltage and current. A prototype circuit of a flyback LED driver system was established to verify whether the theory is consistent with actual results. This study focused on the exponential relationship of LED voltage and current. Conventional simulations usually used linear models to present LED loads. However, the linear model resulted in considerable error between simulation and actual characteristics. Therefore, this study employed a Taylor series to describe the nonlinear characteristic of an LED load. Through precise calculations with Mathcad computation software, the error was effectively reduced. Moreover, the process clarified the influence of temperature on LEDs, which benefited the characteristic analysis of the entire system. Finally, a realized circuit of 120-W flyback LED drivers was established for conducting theory verification, including theoretic analysis and evaluation of the system design process of the flyback converter. The circuit simulation software SIMPLIS was used to demonstrate the system model, which enabled quick understanding of the system framework established in this study. Regarding LEDs, a commercially available aluminum luminaire was used as the output load. The measured results of the actual circuit and the simulation results were remarkably consistent. For the same system at the same temperature, the error between the simulation and actual results was less than 3%, which proved the reliability of the Taylor series simulation.

Objectives. Invasive fungal spondylodiscitis (IFSD) is rare and could be lethal in certain circumstances. Previous literature revealed limited data concerning the outcomes. This study aimed to establish a risk-scoring system. Methods. A total of 53 patients were included in the study from a multi-centered database in Taiwan. All the clinicopathological and laboratory data were retrospectively analyzed. Variables strongly related to 1-year mortality were identified using a multivariate Cox proportional hazards model. A receiver operating characteristic curve was used to express the performance of our IFSD scoring model. Results. Five strong predictors were included in the IFSD score: predisposing immunocompromised state, the initial presentation of either radiculopathy or myelopathy, initial laboratory findings of WBC > 12.0 or < 0.4 103/uL, hemoglobin < 8 g/dL, and evidence of candidemia. 1-year mortality rates for patients with IFSD Scores of 0, 1, 2, 3, and 4 were 0%, 16.7%, 56.3%, 72.7%, and 100%, respectively. The area under the curve of the receiver operating characteristic curve was 0.823. Conclusions. We developed a practical scoring model with easily obtained demographic, clinical, and laboratory parameters to predict the probability of 1-year mortality in patients with IFSD. However, more large-scale and international validations would be necessary before this scoring model is commonly used.

Studies on the detection of layers with elevated black carbon aerosol (BC) concentrations and the formation conditions of these layers help understand the vertical distribution of BC concentrations, which will provide a basis for the assessment of climate effects and early BC pollution warnings. By using the Weather Research and Forecasting with Chemistry (WRF-Chem) numerical model, we performed a numerical simulation analysis on the authenticity of strong elevated BC concentration layers that were detected by an aircraft in the mixing layer over Harbin, China, which is a high-emission area, on a clear sunny afternoon in the early heating period of 2016. We then discuss possible problems and solutions when non-vertical paths are used to detect the vertical distribution of BC concentrations. Finally, we discuss the favorable conditions for the formation of elevated BC concentration layers by weak vertical flow. The results show that the horizontal variability of BC concentration in the mixing layer in the observation area in Harbin was sufficiently large during the measurement. This produced a false elevated layer, as detected by the aircraft during one round of spiral flight in the mixing layer. The root mean square of the horizontal distribution of BC concentration did not change with height in the mixing layer during the daytime, but it decreased with the thickness of the mixing layer and was higher in the mixing layer than in the free atmosphere. Therefore, the thinner the mixing layer, in which the vertical distribution of the BC concentration is detected in an inclined path, the stronger interference of the horizontal variability on the detected results. When a spiral flight detection path is used, the aircraft should fly at least two rounds in the mixing layer. In the daytime, due to strong turbulence in the mixing layer, weak vertical uplift is not favorable for the occurrence of elevated BC concentration layers in the mixing layer. In the nighttime, if weak vertical uplift is well matched with the BC concentration or its vertical gradient, elevated BC concentration layers can be formed in the atmosphere. Compared with upper layers far from the ground, nighttime elevated layers are easier to form in lower layers near the ground because high BC concentrations or large vertical gradients are more likely to occur in the lower layers. Both cases facilitate the occurrence of large vertical upward transport rates of BC.

As noted in the introductory quotation, an ideal map was long ago seen as the map of the map, the map of the map, of the map, and so on endlessly. This recursive perspective on maps, however, has received little attention in cartography. Cartography, as a scientific discipline, is essentially founded on Euclidean geometry and Gaussian statistics, which deal with respectively regular shapes, and more or less similar things. It is commonly accepted that geographic features – such as rivers, cities, streets and building – are not regular and that the Earth’s surface is full of fractal or scaling or living phenomena with far more small things than large ones at different levels of scale. This paper argues for a new paradigm in mapping, based on fractal or living geometry and Paretian statistics, and – more critically – on the new conception of space, conceived and developed by Christopher Alexander, that space is neither lifeless nor neutral, but a living structure capable of being more living or less living. The fractal geometry is not limited to Benoit Mandelbrot’s framework, but is extended towards Christopher Alexander’s living geometry and based upon the third definition of fractal: A set or pattern is fractal if the scaling of far more small things than large ones recurs multiple times. Paretian statistics deals with far more small things than large ones, so it differs fundamentally from Gaussian statistics, which deals with more or less similar things. Under the new paradigm, I make several claims about maps and mapping: (1) Topology of geometrically coherent things – in addition to that of geometric primitives – enables us to see a scaling or fractal or living structure; (2) Under the third definition, all geographic features are fractal or living, given the right perspective and scope; (3) Exactitude is not truth – to paraphrase Henri Matisse – but the living structure is; and (4) Töpfer’s law is not universal, but scaling law is. All these assertions are supported by evidence, drawn from a series of previous studies. This paper demands a monumental shift in perspective and thinking from what we are used to on the legacy of cartography and GIS.

Early debridement and stabilization for pyogenic spondylodiscitis allow early mobilization of the patient and prevent subsequent spinal deformity. Tantalum (Ta) trabecular metal (TM) components have several potential advantages over conventional implant materials, such as its uniformity and structural continuity, strength, low stiffness, high porosity, high coefficient of friction and tantalum trabecular metal enhances the host defense mechanism by increasing leukocyte chemotaxis, phagocytosis, and the bacterial killing rate. A single-stage surgery with a tantalum trabecular metal cage combining two different approaches is sufficient to maintain vertebral stability. This retrospective cohort study included 57 patients, 31 (54%) patients were treated with single-stage debridement and reconstruction with trabecular metal cages, and 26 (45.6%) patients received spine surgery without trabecular metal cages received surgery between January 2018 and March 2021 in our tertiary academic teaching hospital. The CRP values dropped borderline significantly in the TM cage group compared with the non-TM cage group postoperatively. In patients with spondylodiscitis, it is advisable to perform single-stage debridement and reconstruction with a trabecular metal cage, which allows abscess drainage and rapid mobilization, prevents deformity.

Flooding is one major environmental problem facing urban cities causing varying degree of damages to properties and disruptions to socio-economic activities. Nigeria is the most populated African country and Kano metropolis is the second largest urban center in Nigeria and the most populated in Northern Nigeria. The aim of the paper is to conduct flood risk assessment of Kano metropolis. The city is divided into two hydrological basins; Challawa and Jakara Basins. Flood frequency analysis for 2 to 100-year return periods were carried out for both the basins using Log-Pearson Type III distribution and flood inundation and hazard mappings were carried out. Social vulnerability to flood of both basins were carried out using MOVE framework. Assessment of flood risk were carried out using map algebra spatial analyst tool in ArcGIS 10.7. The result shows that an area of 50.91 and 40.56 km2 were vulnerable to a 100-year flood. The flood risk map for the two basins show that 10.50 km2 and 14.23 km2 of land in Challawa and Jakara basins respectively are affected by the risk of a 100-year flood out of which 11.48 km2 are built-up area. As the city is densely populated, with a population density of well over 20,000 persons per square kilometer in the highly built-up locations, this means that much more than 230,000 persons will be affected by the flood risk in the two basins

As Christopher Alexander conceived and defined through his life’s work – The Nature of Order – wholeness is a recursive structure that recurs in space and matter and is reflected in human minds and cognition. Based on the definition of wholeness, a mathematical model of wholeness, together with its topological representation, has been developed, and it is able to address not only why a structure is beautiful, but also how much beauty the structure has. Given the circumstance, this paper is attempted to argue for the wholeness as the scientific foundation of sustainable urban design and planning, with the help of the mathematical model and topological representation. We start by introducing the wholeness as a mathematical structure of physical space that pervasively exists in our surroundings, along with two fundamental laws – scaling law and Tobler’s law – that underlie the 15 properties for characterizing and making living structures. We argue that urban design and planning can be considered to be wholeness-extending processes, guided by two design principles of differentiation and adaptation, to transform a space – in a piecemeal fashion – into a living or more living structure. We further discuss several other urban design theories and how they can be justified by and placed within the theory of wholeness. With the wholeness as the scientific foundation, urban design can turn into a rigorous science with creation of living structures as the primary aim.

Deep convolutional neural networks (CNNs) have been widely used in various medical imaging tasks. However, due to the intrinsic locality of convolution operation, CNNs generally cannot model long-range dependencies well, which are important for accurately identifying breast cancer from unregistered multi-view mammograms. This motivates us to leverage the architecture of Vision Transformers to capture long-range relationships of multiple mammograms from the same patient. For this purpose, we employ local Transformer blocks to separately learn patch relationships within a specific view (CC/MLO) of one side (right/left) of mammogram. The outputs from different views and sides are concatenated and fed into global Transformer blocks, to jointly learn patch relationships between two different views of the left and right breasts. To evaluate the proposed model, we retrospectively assembled a dataset involving 949 sets of CC and MLO view mammograms, which include 470 malignant cases and 479 normal or benign cases. We trained and evaluated the model using a five-fold cross-validation method. Without any arduous preprocessing steps (e.g., optimal window cropping, chest wall or pectoral muscle removal, two-view image registration, etc.), our two-view Transformer-based model achieves lesion classification accuracy of 77.0% and area under ROC curve (AUC = 0.814), outperforming state-of-the-art multi-view CNNs by 3.1% and 3%, respectively. Meanwhile, the new two-view model improves mammographic case classification accuracies of two single-view models by 7.4% (CC) and 4.5% (MLO), respectively. The promising results unveil the great potential of using Transformers to develop high-performing computer-aided diagnosis (CADx) schemes of mammography.

This study aimed to compare the differences in durability and prestress loss between normal-weight concrete (NC) and lightweight aggregate concrete (LWC) prestressed box girders, which were constructed at the same time in the same area, so as to verify the superiority of using synthetic lightweight aggregate (LWA) made from reservoir sediments in prestressed bridges. For the NCs and LWCs used in prestressed box girders, the basic mechanical properties were tested on the one hand, and the durability properties were tested on the other hand. Then, through the prestress monitoring system, the prestress loss of the two groups of the prestressed box girders was tracked. The results of the durability test confirmed that LWC can inhibit the penetration of air, water, and chloride ions by strengthening the interfacial transition zone between the aggregate and the cement paste, thereby improving its durability. Moreover, the magnetic flux prestress loss of the NC prestressed box girder reached 8.1%. In contrast, the magnetic flux prestress losses on both sides of the LWC prestressed box girder were 4.6% and 4.9%, respectively. This verified that, under the same environmental conditions, the use of LWC produced less of a prestress loss than the use of NC.

Construction safety is especially important because the construction industry is so important to a country's development. Significant research and practice have been conducted to mitigate potential risks during construction and improve worker efficiency. With the rapid advancement of cognitive neuroscience and the incorporation of medical technology in recent years, various wearable monitoring devices have been widely used in the construction field for real-time monitoring of workers' physical and mental status. Among these, the use of EEG (Electroencephalogram) in construction environment research allows researchers to gain insight into the physical and mental states of construction workers while performing construction tasks. This review introduces EEG technology and portable EEG devices, followed by an overview of their use in both monitoring workers' adverse reactions and identifying hazards on construction sites, providing an effective guide for EEG research in the construction field and on-site safety management.

Biocompatible and biodegradable poly(butylene succinate-co-adipate) (PBSA)/hexadecylamine-modified PPZn (m-PPZn) nanocomposites were prepared using a melt mixing process. Experimental results of wide-angle X-ray diffraction and transmission electron microscopy revealed that the stacking layers of the m-PPZn were partially intercalated and partially exfoliated into the PBSA polymer matrix. The isothermal crystallization kinetics of PBSA/m-PPZn nanocomposites were studied at the temperature range of 62−70 °C and the half-time for crystallization of 3 wt % PBSA/m-PPZn nanocomposite was reduced by 27−35% compared with that of pure PBSA. This finding suggests that the incorporation of m-PPZn might cause the heterogeneous nucleation and the subsequent crystallization growth, which enhances the isothermal crystallization rate of PBSA/m-PPZn nanocomposite. The biodegradation rates of PBSA using Lipase from Pseudomonas sp. increase as the contents of m-PPZn increase. The degradation behavior of the neat PBSA investigated using the change of weight-average molecular weight belongs to exo-type hydrolysis activity. It is necessary to point out that the change of degree of crystallinity and degradation rate are almost linearly proportional to the loading of hexadecylamine-modified PPZn. This finding would provide an important information for the manufacturing biodegradable PBSA nanocomposites.

To facilitate the promotion and application of the whole process engineering consulting (WPEC) model, the transmission mechanism of influencing factors in WPEC's promotion and application is investigated. It identifies and categorizes the influencing factors within the framework of "external environment-project factors-stakeholders", systematically organizing and summarizing ten primary categories and thirty-eight secondary influencing factors of WPEC's promotion and ap-plication. Utilizing the complex network analysis method, a network of influencing factors in the promotion and application of WPEC is constructed. The network is then converted into three binary networks based on weight, which are subjected to structural analysis and motif analysis. On this basis, the transmission mechanism of influencing factors in WPEC's promotion and applica-tion and its causations are explored.

Conceived and developed by Christopher Alexander through his life’s work: The Nature of Order, wholeness is defined as a mathematical structure of physical space in our surroundings. Yet, there was no mathematics, as Alexander admitted then, that was powerful enough to capture his notion of wholeness. Recently, a mathematical model of wholeness, together with its topological representation, has been developed that is capable of addressing not only why a space is good, but also how much goodness the space has. This paper develops a structural perspective on goodness of space – both large- and small-scale – in order to bridge two basic concepts of space and place through the very concept of wholeness. The wholeness provides a de facto recursive definition of goodness of space from a holistic and organic point of view. A space is good, genuinely and objectively, if its adjacent spaces are good, the larger space to which it belongs is good, and what is contained in the space is also good. Eventually, goodness of space – sustainability of space – is considered a matter of fact rather than of opinion under the new view of space: space is neither lifeless nor neutral, but a living structure capable of being more living or less living, or more sustainable or less sustainable. Under the new view of space, geography or architecture will become part of complexity science, not only for understanding complexity, but also for making and remaking complex or living structures.

Water splitting technology is an efficient approach to generate hydrogen (H2) energy, which can well address the problems of environmental deterioration and energy shortage, as well as establishment of a clean and sustainable hydrogen economy powered by renewable energy sources due to the green reaction of H2 with O2. While the efficiency of H2 production by water splitting technology is intimately related with the reactions on electrode. Nowadays, the efficient electrocatalysts in water splitting reactions are the precious metal-based materials, i.e., Pt/C, RuO2 and IrO2. Ni (Co, Fe)-based layered double hydroxides (LDH) 2D materials are the typical non-precious metal-based materials in water splitting with advantages of low cost, excellent electrocatalytic performance and simple preparation methods, which exhibits a great potential for the substitution for precious metal-based materials. This review summarizes the recent progress of Ni (Co, Fe)-based LDH 2D materials for water splitting, which mainly focuses on discussing and analyzing the different strategies to modify LDH materials towards high electrocatalytic performance. We also discuss the recent achievements including their electronic structure, electrocatalytic performance, catalytic center, preparation process and catalytic mechanism. Furthermore, the characterization progress in revealing electronic structure and catalytic mechanism of LDH is highlighted in this review. Finally, we put forward some future perspectives related to design and explore advanced LDH catalysts in water splitting.

Convolutional neural networks (CNNs) face challenges in capturing long-distance text correlations, and Bidirectional Long Short-Term Memory (BiLSTM) networks exhibit limited feature extraction capabilities for text classification of work order. To address the abovementioned problems, this work utilizes an ensemble learning approach to integrate model elements efficiently. This study presents a method for classifying work order texts using a hybrid neural network model called BERT-BiLSTM-CNN. First, use Bert for preprocessing to obtain text vector representations. Then, capture context and process sequence information through BiLSTM. Next, capture local features in the text through CNN. Finally, obtain classification results through Softmax. Through comparative analysis, the method of fusing these three models is superior to other hybrid neural network model architectures in multiple classification tasks. It has a significant effect on work order classification.

Rheumatoid arthritis (RA) is an autoimmune inflammatory disease characterized by chronic synovitis and progressive destruction of cartilage and bone. RA is commonly accompanied by extra-articular comorbidities. The pathogenesis of RA and its comorbidities is complex and not completely elucidated. Assembly of NLRP3 inflammasome activates caspase-1, which induces the maturation of interleukin (IL)-1β and IL-18 and leads to cleavage of gasdermin D with promot-ing pyroptosis. Although the available therapeutic agents are effective for RA treatment, their high cost and increased infection rate are causes for concern. Recent evidence revealed the components of NLRP3 inflammasome as potential therapeutic targets in RA and its comorbidities. This nar-rative review summarizes the current research evidence regarding the pathogenic role and the therapeutic potential of NLRP3 inflammasome in RA and its comorbidities. Areas covered. We searched the MEDLINE database using the PubMed interface and reviewed English-language literature on NLRP3 inflammasome from 2000 to 2023. Its pathogenic role and therapeutic potential in RA and its comorbidities are the focus of this review. Expert opinion. NLRP3 inflammasome may play a critical role in both innate and adaptive im-munity, and its dysfunction contributes to the pathogenesis of RA and its comorbidities. Conse-quently, the components of NLRP3 inflammasome signaling represent promising therapeutic tar-gets, and ongoing research might lead to the development of new, effective treatments for RA and its comorbidities.

Fire is a common natural disturbance in forest ecosystems and plays an important role in subsequent vegetation patterns. Based on the spatial sequence method instead of the time successional sequence method, this study selected burned areas in different locations in the Anning River Basin, which contains typical dry valleys. Quadrat surveys and quantitative classification were used to identify the vegetation classification, distribution pattern, and environmental interpretation during the natural restoration process after forest fire. The results showed that: (1) the vegetation community in the early stage of natural recovery after forest fire disturbance could be divided into seven community types, and Quercus guyavaefolia H. Leveille (Qg) was the dominant species in the community; (2) vegetation samples could be divided into five ecological types, and the classification and distribution pattern of community types in this region changed most obviously with altitude; and (3) detrended correspondence analysis could clearly classify vegetation community types, and detrended canonical correspondence analysis could well reveal the relationships between species and environmental factors. This study provides a scientific basis guiding the restoration of ecosystem structural stability and biodiversity in burned areas.

The objective of this study was to synthesize 9-/13-position substituted berberine derivatives and evaluated their cytotoxic and photocytotoxic effects against three human cancer cell lines. Among all the synthesized compounds, 9-O-dodecyl- (5e), 13-dodecyl- (6e) and 13-O-dodecyl-berberine (7e) exhibited stronger growth inhibition against three human cancer cell lines, (HepG2, HT-29 and BFTC905), in compare with structurally related berberine (1). These three compounds also showed the photocytotoxicity in human cancer cells in a concentration-dependent and light dose-dependent manner. Through flow cytometry analysis, we found out a lipophilic group at 9-/13-position of berberine may have facilitated its penetration into test cell and hence enhanced its photocytotoxicity on human liver cancer cell HepG2. Further, in cell cycle analysis, 5e, 6e and 7e induced HepG2 cells to arrest at S phase and caused apoptosis upon irradiation. In addition, photodynamic treatment of berberine (1) and its derivatives 5e, 6e and 7e again showed a significant photocytotoxic effects on HepG2 cells, induced remarkable cell apoptosis, greatly increased intracellular ROS level and the loss of mitochondrial membrane potential. These results over and again confirmed that berberine derivatives 5e, 6e and 7e greatly enhanced photocytotoxicity. Taking together, the test data led us to conclude that berberine derivatives with a dodecyl group at 9-/13-position could be great candidates for the anti-liver cancer medicines developments.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

This article presents a method for extracting neural signal features to identify the imagination of left and right hand grasping movements. A functional magnetic resonance imaging (fMRI) experiment is employed to identify four brain regions with significant activations during motor imagery(MI) and the effective connections between these regions of interest (ROIs) were calculated using Dynamic Window-level Granger Causality (DWGC). Then, a real-time fMRI(rt-fMRI) classification system for left and right hand MI is developed using the Open-NFT platform. The experimental results show that incorporating effective connections can enhance the average accuracy of real-time three-class classification (rest, left hand and right hand) by 3% in comparison to traditional multivoxel pattern classification analysis(MVPA). Moreover, it significantly improves classification accuracy during the initial stage of MI tasks while reducing the latency effects in real-time decoding. The study suggests that the effective connections obtained through the DWGC method serve as valuable features for real-time decoding of MI using fMRI. Moreover, they exhibit higher sensitivity to changes in brain states. This research offers theoretical support and technical guidance for extracting neural signal features in the context of fMRI-based studies.

A simulation test system for the two-dimensional (2D) fuze overload loading process was designed to address the loading issues of recoil overload and centrifugal overload in fuze safety and arming (S&amp;A) devices. By incorporating centrifuge rotation energy storage, impact acceleration simulation, and equivalent centrifugal rotation simulation, a block equipped with a fuze S&amp;A device was accelerated instantly upon being impacted by a centrifuge-driven impact hammer, simulating recoil overload loading. The impact hammer was retracted instantaneously by adopting an electromagnetic brake, which resulted in the centrifugal rotation of the block around its track, to simulate the centrifugal overload loading. The dynamic equations of the simulation test system and the equations of impact hammer motions were established, whereby the rotation speed of the centrifuge and the braking force of the electromagnetic brake were calculated and selected. A dynamic model of the collision between the impact hammer and block was established using ANSYS/LS-DYNA software for simulation analysis. The acceleration curves of the recoil overload and centrifugal overload with variations in the centrifuge speed, cushion material, and buffer thickness were obtained, which verified the feasibility of the proposed loading simulation method. 2D overload loading simulation tests were performed using the developed simulation system, and the acceleration curves of the recoil overload and centrifugal overload were measured. The test results indicated that the proposed system can accomplish 2D overload loading simulations for a recoil overload of several 10000 g and centrifugal overload of several 1000 g.

Attracting and retaining international students has been widely discussed in higher education settings. Increasing the number of international students has become an indispensable strategy for national and global competition. This study focuses on effective strategies and international students' issues regarding satisfaction in the most popular STEM (science, technology, engineering, and mathematics) programs. We designed a structural equation modeling (SEM) method to determine the effect of institutional mediation between push factors and satisfaction factors for the development of better strategies by which to attract and retain international students. Taking Taiwan as an example, this study employed a self-designed questionnaire to collect data: 485 degree-seeking international students in STEM programs were invited and successfully participated in this study during spring 2021. IBM SPSS 26 and AMOS 26 (Analysis of Moment Structure) were used to carry out the data analysis. We employed reliability, factor, and SEM analyses. This study assumed that the impact of push factors can be modified by institutional situations and result in international students’ satisfaction with their learning and environment and regarding migration policy. The results revealed that the predictors, mediation, and criteria were significant at the 0.05 or 0.01 levels. The findings suggest that push factors impact international students’ satisfaction when using institutional leadership and international strategy. The results of the bootstrap with a generalized least square method showed that the SEM model fit in 2000 bootstrap samples. The effect of institutional mediation can provide useful information for STEM programs to boost their future recruitment and retention strategies. This study provides an innovative approach to the detection of issues among international students in specific programs. These findings can enrich our knowledge regarding attracting and retaining global students in higher education settings.

Following our previous success in identifying new steroid-based anticancer agents, we herein disclosed the structural requirements for retaining high potency against cancer cells and associated modes of action. The structurally novel steroidal dimer by001 inhibited growth of different esophageal cancer cells and colony formation at low micromolar levels, elevated cellular ROS levels and caused mitochondrial dysfunction. Mechanistic studies showed that by001 induced cell death through the mitochondria and death receptor-mediated apoptotic pathways and autophagy induction, as well as inhibited migration.

We present a generic and open-source framework for the numerical modeling of the expected transport and storage mechanisms in unconventional gas reservoirs. These unconventional reservoirs typically contain natural fractures at multiple scales. Considering the importance of these fractures in shale gas production, we perform a rigorous study on the accuracy of different fracture models. The framework is validated against an industrial simulator and is used to perform a history-matching study on the Barnett shale. This work presents an open-source code that leverages cutting-edge numerical modeling capabilities like automatic differentiation, stochastic fracture modeling, multi-continuum modeling and other explicit and discrete fracture models. We modified the conventional mass balance equation to account for the physical mechanisms that are unique to organic-rich source rocks. Some of these include the use of an adsorption isotherm, a dynamic permeability-correction function, and an embedded discrete fracture model (EDFM) with fracture-well connectivity. We explore the accuracy of the EDFM for modeling hydraulically-fractured shale-gas wells, which could be connected to natural fractures of finite or infinite conductivity, and could deform during production. Simulation results indicates that although the EDFM provides a computationally efficient model for describing flow in natural and hydraulic fractures, it could be inaccurate under these three conditions: 1. when the fracture conductivity is very low. 2. when the fractures are not orthogonal to the underlying Cartesian grid blocks, and 3. when sharp pressure drops occur in large grid blocks with insufficient mesh refinement. Each of these results are very significant considering that most of the fluids in these ultra-low matrix permeability reservoirs get produced through the interconnected natural fractures, which are expected to have very low fracture conductivities. We also expect sharp pressure drops near the fractures in these shale gas reservoirs, and it is very unrealistic to expect the hydraulic fractures or complex fracture networks to be orthogonal to any structured grid. In conclusion, this paper presents an open-source numerical framework to facilitate the modeling of the expected physical mechanisms in shale-gas reservoirs. The code was validated against published results and a commercial simulator. We also performed a history-matching study on a naturally-fractured Barnett shale-gas well considering adsorption, gas slippage & diffusion and fracture closure as well as proppant embedment, using the framework presented. This work provides the first open-source code that can be used to facilitate the modeling and optimization of fractured shale-gas reservoirs. To provide the numerical flexibility to accurately model stochastic natural fractures that are connected to hydraulically-fractured wells, it is built atop other related open-source codes. We also present the first rigorous study on the accuracy of using EDFM to model both hydraulic fractures and natural fractures that may or may not be interconnected.

People wore clothes for warmth, survival and necessity in modern life as well but in modern era, eco-friendliness, shorten production time, design, and intelligence also matters. The seamless bonding technology strengthen the bond between fabrics in textiles, while Grey relational analysis (GRA) can be applied to fabrics to measure the relationship between data series and determine the closeness of each data series. In this study, polyurethane prepolymer, 2-Hydroxyethyl acrylate (2-HEA) as an end-capping agent, and n-octyl acrylate (ODA) as a photo-initiator were used to synthesize dual-curing polyurethane hot-melt adhesive. The Taguchi quality engineering and grey relational analysis used to discuss the influence of different mole ratio of NCO:OH, and the effect of the molar ratio of addition of octyl decyl acrylate on the mechanical strength. The Fourier transform infrared spectroscopy (FTIR) results showed the termination of prepolymer's polymerization reaction and the C=O peak intensity at 1730 cm-1 indicating the efficient bonding to main chain. The high molecular weight polymer (20,000-30,000) described by advanced polymer chromatography (APC) confirmed the polyurethane polymer bonded with octyl decyl acrylate to achieve the photo-thermosetting effect. The thermogravimetric analysis (TGA) results showed the thermal decomposition temperature of polyurethane hot melt adhesive also increased and highest pyrolysis temperature (349.89℃) for the polyhydric alcohols. The high value of shear strength (34.94 kg/cm2) as well as peel strength (1.68 kg/cm) were also observed in dual-cure photo-thermosetting polyurethane hot melt adhesive. The signal-to-noise ratio also used to generate the grey relational degree. It was observed that the best parameter ration of NCO: OH was 4:1 with 5 moles of monomer. The Taguchi quality engineering method was used to find the parameters of single quality optimization, and then the grey relation calculation was used to obtain the parameter combination of multi-quality optimization for thermosetting polyurethane hot melt adhesive. The study aims to meet the requirements of seamless bonding in textile factories and optimized experimental parameter design by setting target values can effectively increase production speed, reduce processing time and costs as well.

Augment reality (AR) is crucial for immersive human-computer interaction (HCI) and vision of artificial intelligence (AI). Labeled data drove object recognition in AR. However, manual annotating data is expensive and labor-intensive, and furthermore, scanty labeled data limits the application of AR. Aiming at solving the problem of insufficient training data in AR object recognition, an automated vision data synthesis method called BAGAN is proposed in this paper based on the 3D modeling and GAN algorithm. Our approach has been validated to have better performance than other methods through image recognition task on natural image database ObjectNet3D. This study can shorten the algorithm development time of AR and expand the application scope of AR, which is of great significance to immersive interactive systems.

Background: Atherosclerosis (AS), a key pathological contributor of cardiovascular diseases (CVDs), was characterized by formation of atherosclerotic plaque in aortic wall and caused high mortality and morbidity worldwide. Factors contributing to the initiation and progression of AS included vascular endothelial dysfunction, dyslipidemia, inflammation, and oxidative stress. Shexiang Baoxin Pill (SBP) was a traditional Chinese medicine that had been widely applied in clinic and proved to be effective for patients with CVDs. However, the mechanisms underlying its anti-atherosclerotic effects have not been completely elucidated. The study aimed to investigate the protective effects of SBP on AS and its potential mechanisms. Methods: Different dose of SBP was orally administered in apolipoprotein E-deficient (ApoE-/-) mice treated with a high-fat diet (HFD). Histopathological and immunohistochemical analysis, ELISA, untargeted metabolomics analysis, 16S rRNA sequence analysis, and spearman analysis were applied to identify the protective effects and mechanisms of SBP in HFD-induced AS. Results: SBP significantly alleviated HFD-induced atherosclerotic lesion both in aorta and aortic sinus with a reduction in serum levels of total cholesterol (TC), triglycerides (TG) and low-density lipoprotein cholesterol (LDL-C), as well as interleukin-6 (IL-6) and interleukin-1β (IL-1β), and increased high-density lipoprotein cholesterol (HFD-C) level with no significant change of body weight in HFD-induced ApoE-/- mice. Mechanismly, SBP markedly reshaped the gut microbiota composition and associated metabolomic characteristics. 2 differential intestinal floras at phylum level and 8 differential microbes at genus level, 5 metabolic pathways and 9 differential fecal metabolites related to CVDs were figured out. Besides, intensive correlation between 8 differential microbes and 9 fecal metabolites was observed. Conclusions: Our results showed that SBP could improve HFD-triggered serum lipid disorder, systematic inflammation, and contribute to the alleviation of atherosclerotic lesion. The antiatherogenic properties of SBP might partly result from the reshaping of the gut microbiota and fecal metabolic profile.

Inosine 5'-monophoaphate (IMP) allows animals to sense umami. Intake of IMP in C57/KsJ-db/db (db/db) mice induced lipohyperplasia causing the liver cirrhosis, however, how to that of in normal mammals injure health is still unclear. Thus, we had investigated that intake of IMP in C57BL/6J mice effected its metabolic functions. We found that intake of 255 M/d IMP in C57BL/6J mice for 4 months induced hyperlipidemia and body fat rate raised. In mechanism, the expressions of ACC1 and phosphorylated ACC2 in hepatocytes were increased though IMP promoting phosphorylation of AMPK. The increased ACC1 promoted the conversion of acetyl-CoA into TG. These TG were transported out of hepatocytes to avoid NAFLD, causing a deficiency of acetyl-CoA in liver, and then the increased phosphorylated ACC2 promoted cytoplasm fatty acids into mitochondria to convert into acetyl-CoA though the fatty acids β-oxidation pathway, causing a deficiency of fatty acids. Therefore, liver enhanced the absorption of exogenous fatty acids, which were converted into TG caused lipohyperplasia. Moreover, intake of IMP in normal mice induced complement system weaken in liver causing mild inflammation. Our data not only alerted that humans avoid excessive intake of IMP, but also provided novel insights into the adipose of metabolic dysfunctions.

Permeable asphalt pavement refers to an asphalt mixture layer with an air void content of more than 18% and internal water permeability and drainage capabilities, which can quickly drain away water on the road surface, improve rainy day travel safety and ride comfort. This paper aims to explore the optimal asphalt mixture mix design for long longitudinal slope roads. By using CT scanning technology to analyze the air void content of different rotated and compacted asphalt mixture specimens, and extensively testing and evaluating the performance of permeable pavement mixtures, the following conclusions are drawn: Based on the research philosophy of functional integration, a new asphalt mixture gradation suitable for long longitudinal slope roads is proposed, with the optimal key factor composition being: 0.075mm passing rate of 7%, 2.36mm passing rate of 20%, 9.5mm passing rate of 55%, and oil-stone ratio of 4.8%. The FAM mixture was divided into three parts for air void analysis, with the upper part having a slightly higher air void content than the lower part. The air void distribution diagram of the FAM mixture is concave, with higher air void rate curves on both sides and a lower middle curve. Compared with laboratory dry measurement method, CT scanning test showed slightly higher air void content in specimens. Through dynamic modulus testing, the strength requirement for road asphalt mixture in pavement structure design was evaluated. It was found that at high temperature conditions (50℃), the minimum dynamic modulus value of the FAM mixture was 323 MPa, with a peak value of 22746MPa at a temperature of -10℃ and a frequency of 25HZ. The dynamic modulus value at high temperature conditions is lower than at low temperature conditions, while the dynamic modulus value at high frequency conditions is higher than at low frequency conditions. This study provides useful information and experimental data for the design of new asphalt mixtures for long longitudinal slope roads, and has conducted in-depth research on the air void distribution and performance of the mixture, providing strong support for related research fields and practical applications.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In this study, based on a new quantum integral identity, the authors establish some quantum estimates of Hermite-Hadamard type inequalities for convex functions. These results generalize and improve some known results given in literatures.

Patients with schizophrenia had higher mortality risks and the role of antipsychotic medications remained inconclusive. In an aging society, elderly schizophrenia patients warrant increased attention. In this study, we aimed to explore medication dosage associations with mortality in schizophrenia patients, using Taiwan's national healthcare database from 2010 to 2014, with 102,964 patients with schizophrenia, and a subgroup of 6,433 elderly patients, compared to an age- and gender-matched control group. The findings revealed that schizophrenia patients with no antipsychotic exposure had the highest mortality risk as compared to the control sample—with a 3.61 and 3.37-fold risk for overall and cardiovascular mortality respectively in age and gender-adjusted model, followed by high, low, and moderate exposure groups. A similar pattern was observed in elderly schizophrenia patients but high exposure to antipsychotics was associated with the highest risk in both overall and cardiovascular mortality in elderly patients, with a 3.01, and 2.95-fold risk), respectively. In conclusion, the use of antipsychotics is beneficial to patients with schizophrenia, with recommended exposure levels being low to moderate. In elderly patients, high antipsychotic exposure was associated with the highest mortality risk. We should pay more attention to antipsychotic dosage in elderly schizophrenia patients.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Cadmium (Cd) contamination in rice grains is posing a significant threat to global food security. To restrict the transport of Cd in the soil-rice system, an efficient way is to use the ionomics strate-gy. Since calcium (Ca) and Cd have similar ionic radii, their uptake and translocation may be linked in multiple aspects in rice. However, the underlying antagonistic mechanisms are still not fully understood. Therefore, we first summarized the current knowledge on the physiological and molecular footprints of Cd translocation in plants and then explored the potential antagonistic points between Ca and Cd in rice, including exchange adsorption on roots, plant cell wall compo-sition, co-transporter gene expression, and transpiration inhibition. This review provides sugges-tions for the Ca/Cd interacting study in rice and introduces the ionomics research to better control the accumulation of Cd in plants.

Hexabromocyclododecane (HBCD) was most important flame retardant in Expanded Polystyrene foam and Extruded Polystyrene foam in the past forty years in the world. China was the major producer and user of HBCD, and the total HBCD production was about 0.3 million tons. Although HBCD has been completely banned in China in 2021 because of its long-range transport, bioaccumulation and toxicity, there's still a lot of residues in environment. Therefore, we reviewed multiple studies concerning the distribution of HBCD in diverse environmental matrices, such as air, dust, soil, water, sediment and biota. Results revealed that HBCD levels in different environments in China present a geographical variation and were at high level compared with other countries. In all environmental media, relatively high HBCD concentrations have been found in industrial and urban areas. Industrialization and urbanization are two important factors that influence the concentration and distribution of HBCD in the environment. In terms of isomer, γ-HBCD was the dominant isomer in soil, water, and sediment, while in the biota, α-HBCD was the predominant isomer.