The modeling of tilting-pad journal and thrust bearings presents a level of complexity beyond that of bearings of fixed-arc geometry, particularly with regard to dynamic influences. With tilting-pad bearings, the theory surrounding the fluid film must be complemented with representative modeling of the pad dynamics. What has been recognized in recent decades has been the significance of the pad support, in particular the flexibility of the pivot region of the pad. The typical model for including the stiffness of the pivot has been based on Hertzian contact theory. Some researchers have been noting that the Hertzian theory does not permit sufficient flexibility in the pivot region. It is suggested that the contact mechanics at the pivot would be better represented as a pairing of rough surfaces. The modeling used here is based on a statistical asperity micro-contact theory for rough-surface line contact that has been extended to include contact stiffness. This model has been applied to the determination of the effective dynamic properties of tilting-pad bearings. The results show that pivot stiffness can be as low as one-third the stiffness determined by Hertzian theory. Comparison to published experimental results confirms the significance of the rough-surface modeling, particularly for the line contacts associated with rocker-back tilting pads.

We discuss a remote sensing system that is used to simultaneously detect range-resolved differential absorption LIDAR (light detection and ranging; DIAL) signals and integrated path DIAL signals (IP-DIAL) from aerosol targets for ranges up to 22 km. The DIAL/IP-DIAL frequency converter consists of an OPO pumped at 1064 nm to produce light at 1.6 μm and operates at 100 Hz pulse repetition frequency. The probe light is free space coupled to a movable platform that contains one transmitter and two receiver telescopes. Hybrid photon counting/current systems increase the dynamic range for detection by two orders of magnitude. Range resolved and column integrated dry-air CO2 and CH4 mixing ratios are obtained from line shape fits of CO2 and CH4 centered at 1602.2 nm and 1645.5 nm, respectively and measured at 10 different frequencies over ≈ 1.5 cm-1 bandwidth. The signal-to-noise ratios (SNR) of the IP-DIAL returns from cloud aerosols approach 1000:1 and the uncertainties in the mixing ratios weighted according to the integrated counts over the cloud segments range from 0.1 % to 1 %. The range averaged DIAL mixing ratios are in good agreement with the IP-DIAL mixing ratios at the 1 % to 2 % level for both CO2 and CH4. These results can serve as a validation method for future active and passive satellite observational systems.

Protected areas have been used worldwide to conserve natural resources. Nevertheless, economic activities to provide income for communities living inside and surrounding conservation areas remain an issue. This study aimed to assess the sustainability of a Deuterodon iguape hatchery, placed inside an Atlantic Rainforest Park, to leverage this small native fish's grow-out farming, affording income and food security for local families. We have used a set of indicators of economic, social, and environmental sustainability. The initial investment is about US$ 40,000, which returned in ~2 years. The internal rate of return is close to 50%, including the externality costs, which is attractive for public and private investments. The hatchery generated few direct jobs, but the workforce can be recruited in the community, and hatchery can enable the establishment of several small grow-out farms, leveraging the development of indirect jobs and self-employments. The system had a low environmental impact, showing minor release of pollutants, low risk for biodiversity, and absorption of 18 g of CO2 equivalent per thousand post-larvae produced, contributing to the struggle against climate change. Therefore, D. iguape hatchery demonstrates the potential of combining biodiversity conservation and income generation, meeting the Sustainable Development Goals of Agenda 2030.

Freshwater pond aquaculture is the prevailing fish culture system worldwide, especially in developing countries. Climate change outcomes and inadequate environmental practices challenge its sustainability. This study applies emergy synthesis to assess the environmental performance of freshwater pond aquaculture in Brazil, aiming to identify and propose practices towards sustainability. As a study model, nine semi-intensive lambari farms operating at three levels of management were evaluated: low (LC), moderate (MC) and high (HC) control. Results showed that the main inputs for LC were services (27-46%), feed (7-39%), and water (15-21%), while for the MC and HC farms, they were feed (35-49% and 17-48%, respectively) and services (33-39% and 26-36%, respectively). All farms required more than 60% of their emergy from purchased inputs, resulting in low emergy sustainability index (ESI = 0.1-0.5). Replacing animal protein and oil on diet composition by vegetal sources, using superficial water instead of springwater, increasing juvenile productivity, and controlling pond fertilization can lead all systems to higher efficiency and resilience, increasing sustainability.

Lipophilicity can be measured with different methods, such as Shake-Flask or liquid chromatography. HPLC presents the advantage of overcoming solubility issues and therefore extending the range of lipophilicity to high values. A specific HPLC method, called ELogD, had been developed 20 years ago on a C₁₆-amide stationary phase, enhancing hydrophobic and hydrogen bond interactions to mimic octanol-water partition. The emergence of novel stationary phases added to the need for a less complex mobile phase has led to the development of a new HPLC assay called alphaLogD, applicable to neutral and basic compounds at pH 7.4, that combines superficially porous particles, a high number of equilibriums between solutes and stationary phase, and results in a lower number of isocratic methods to determine the logk’_w at a higher throughput. Statistical studies have been run to successfully evaluate the alphaLogD method compared to the Shake-Flask method and to allow this lipophilicity measurement into the so-called Beyond-Rule-of-5-molecules space.

Predicting how a genetic change affects a given character is a major challenge in biology, and being able to tackle this problem relies on our ability to develop realistic models of gene networks. However, such models are rarely tractable mathematically. In this paper, we propose a mathematical analysis of the sigmoid variant of the Wagner gene-network model. By considering the simplest case, that is, one unique self-regulating gene, we show that numerical simulations are not the only tool available to study such models: theoretical studies can be done too, by mathematical analysis of discrete dynamical systems. It is first shown that the particular sigmoid function can be theoretically investigated. Secondly, we provide an illustration on how to apply such investigations in the case of the dynamical system representing the one self-regulating gene.

This paper presents a concise mathematical framework for investigating both feed-forward and backward process, during the training to learn model weights, of an artificial neural network (ANN). Inspired from the idea of the two-step rule for backpropagation, we define a notion of F_adjoint which is aimed at a better description of the backpropagation algorithm. In particular, by introducing the notions of F-propagation and F-adjoint through a deep neural network architecture, the backpropagation associated to a cost/loss function is proven to be completely characterized by the F-adjoint of the corresponding F-propagation relatively to the partial derivative, with respect to the inputs, of the cost function.

The goals of the Agenda 2030 require a significant effort to educate and train new generations on sustainability issues. This article presents an initiative in favor of the evolution of the contents and the pedagogy of economics at the University level. We present the new “Ecological Money and Finance” textbook developed by SDSN France. We detail the assumptions, contents and learning objectives proposed in this new textbook. Then, we describe how it can be used in the framework of an experiential pedagogy of economics, taking as a case study the fundamental economics course of the Grande Ecole program at KEDGE BS.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Gyroscopes are fascinating instruments with a history of about 200 years. When J.G.F. Bohnenberger presented his machine to his students in 1810 at the University of Tuebingen, Germany, nobody could have foreseen that this fascinating development would be used for complex orientation and positioning. At the University of Stuttgart, Germany, a collection of 160 exhibits is available and in transition for a sustainable future. Here, the systems are digitized in 2D, 2.5D and 3D and are made available for a world-wide community using OpenAccess platforms. The technologies being used are Computed Tomography, Computer Vision, Endoscopy and Photogrammetry. The workflows for combining voxel representations and colored point clouds are described, to create Digital Twins of the tangible assets. Advantages and disadvantages are discussed und work for near future is outlined in this new and challenging field of Tech Heritage digitization.

TThe number of supermarkets offering a grocery delivery has been increasing during the last years. Many studies deduce CO₂ emission savings using this concept. Since the delivery of groceries also consumes energy and produces emissions, break-even points can be calculated, from where the delivery has environmental advantages compared to the customer pickup. In this paper, influences of differing vehicle use on break-even points for savings of energy and CO₂ emissions are analyzed for the case of Haidhausen Süd, a city district of Munich in Germany. Internal combustion engine and electric vehicles are investigated to depict current as well as future trends. After an introduction to the used methodology, the potential to save energy and CO₂ emissions related to the delivery of groceries in the chosen district of Munich is evaluated. Afterwards, influences on the break even points are presented and discussed. As the results show, a delivery of groceries leads to energy and carbon dioxide savings in a wide range of private vehicle use for grocery shopping trips. Nevertheless, if the complete customer vehicle fleet is electrified, the use of delivery vehicles with an internal combustion engine can cause an additional environmental impact at the current modal split for shopping trips in Germany.

The Greenland Ice Sheet is now the largest land ice contributor to global sea level rise, largely driven by increased surface meltwater runoff from the ablation zone, i.e. areas of the ice sheet where annual mass losses exceed gains. This small but critically important area of the ice sheet has expanded in size by ~50% since the early 1960s, and satellite remote sensing is a powerful tool for monitoring the physical processes that influence its surface mass balance. This review synthesizes key remote sensing methods and scientific findings from satellite remote sensing of the Greenland Ice Sheet ablation zone, covering progress in 1) radar altimetry, 2) laser (lidar) altimetry, 3) gravimetry, 4) multispectral optical imagery and, 5) microwave and thermal imagery. Physical characteristics and quantities examined include surface elevation change, gravimetric mass balance, reflectance, albedo, and mapping of surface melt extent and glaciological facies and zones. The review concludes that future progress will benefit most from methods that combine multi-sensor, multi-wavelength, and cross-platform datasets designed to discriminate the widely varying surface processes in the ablation zone. Specific examples include fusing laser altimetry, radar altimetry, and optical stereophotogrammetry to enhance spatial measurement density, cross-validate surface elevation change, and diagnose radar elevation bias; fusing optical imagery, radar imagery, and microwave scatterometry to discriminate between snow, liquid water, refrozen meltwater, and bare ice near the equilibrium line altitude; combining optical reflectance with laser altimetry to map supraglacial lake, stream, and crevasse bathymetry; and monitoring the inland migration of snowlines, surface melt extent, and supraglacial hydrologic features.

Since the outbreak of SARS CoV-2 infection (Covid-19), healthcare professionals worldwide have been trying to find disease management and control alternatives to encourage immunotherapies. Immunotherapy is an efficient therapeutic option used against comparable viral contaminations such as MERS-CoV and SARS-CoV. The aim of the current study is to assess the existing knowledge associated with SARS-CoV-2 immunotherapy. Information available in published articles and their quality highlights the importance of following strict scientific rules for clinical outcomes. Thus, these studies have shown enough data to confirm that immunomodulation is the main topic investigated in research about Covid-19 therapy. Therefore, it is possible saying that immunotherapy is certainly the appropriate option against this virus.

Two welcome extensions of evolutionary thinking have come to prominence over the last thirty years: the so-called “extended evolutionary synthesis” (EES) and debate about biological kinds and individuals. These two agendas have, however, remained orthogonal to one another. The EES has mostly restricted itself to widening the explanations of adaptation offered by the preceding “modern evolutionary synthesis” by including additional mechanisms of inheritance and variation; while discussion of biological kinds has turned toward philosophical questions of essential vs. contingent properties of life forms and realist vs. epistemological approaches to categorization and classification. Here we attempt to broaden the explanatory scope of evolutionary theory by linking these two agendas. We expand on the mechanistic orientation of the EES, using new understandings of networked systems of components in order to engage the distinct intellectual challenge of the origination of historical kinds. With this phrase we designate a subset of natural kinds that acquires, through evolutionary processes, a quasi-independent lineage-history. Such kinds emerge in both biology and culture, and we enlarge the limited number of historical kinds that have thus far been recognized in evolutionary biology in a series of paradigmatic exemplars, from genes and cell types to rituals and music. For each exemplar we discern specific mechanisms by which it arose and persists; comparing these, we suggest a general unity in the ways in which diverse historical kinds originate.

Since its inception, evolutionary theory has experienced a number of extensions. The most important of these took the forms of the Modern Evolutionary Synthesis (MES), embracing genetics and population biology in the early 20^th century, and the Extended Evolutionary Synthesis (EES) of the last thirty years, embracing, among other factors, non-genetic forms of inheritance. While we appreciate the motivation for this recent extension, we argue that it does not go far enough, since it restricts itself to widening explanations of adaptation by adding mechanisms of inheritance and variation. A more thoroughgoing extension is needed, one that widens the explanatory scope of evolutionary theory. In addition to adaptation and its various mechanisms, evolutionary theory must recognize as a distinct intellectual challenge the origin of what we call “historical kinds.” Under historical kinds we include any process that acquires a quasi-independent and traceable lineage-history in biological and cultural evolution. We develop the notion of a historical kind in a series of paradigmatic exemplars, from genes and homologues to rituals and music, and we propose a preliminary characterization.

As sessile organisms, plants face a wide range of abiotic stresses, with salinity being a prominent constraint affecting their growth, development, and productivity, particularly in arid and semi-arid regions. This study focused on understanding how salinity impacts Jatropha curcas, an important oilseed plant for biodiesel production. By examining the anatomy and ultrastructure of stomata and chloroplasts, we investigated the effects of prolonged salinity stress on J. curcas. This stress led to changes in stomatal density, stomatal index, and ostiole aperture, which case an imbalance of water conductivity in the xylem. Through transmission electron microscopy, we explored the subcellular organization of J. curcas chloroplasts and their contribution to plant photosynthetic efficiency, providing insights into their role in this process. Notably, salinity treatment resulted in a significant increase in starch granules accumulation, leading to impaired the granal and stromal grana lamellae, destroying this ultrastructure. Our findings indicate that the anatomy and ultrastructure of chloroplasts play a crucial role in influencing photosynthetic efficiency and hydraulic conductivity. This study offers new perspectives on the structure and function of chloroplasts in J. curcas, presenting innovative opportunities to develop strategies that enhance biofuel production in areas with high soil salinity.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

Recently a measure termed F* was described, as an interpretable transformation of the F measure, also known as the Dice coefficient. Using elementary mathematical methods, it is shown that F* is in fact identical to a previously described measure, monotonically related to the F measure, and variously termed in previous publications, dating from the late 19^th to the late 20^th century, as the ratio of verification, the Jaccard similarity measure or index, the threat score, the Tanimoto index, and the critical success index. The origins of these different terms in different disciplines (weather forecasting, ecology, machine learning) may explain the repeated independent redescription of this measure.

Out of a worldwide annual incidence of ~150 million cases for urinary tract infection (UTI), >25% of outpatient prescriptions of oral antimicrobial treatment (OAT) are for cystitis not complicated by sepsis. OAT aids the immune cells infiltrating urothelium to eliminate uropathogens attaching and invading urothelium amidst hyperosmotic urine. This adaptability of uropathogens and the short interval between Penicillin sale and the first antimicrobial resistance (AMR) report suggests that AMR is a 3.8 billion years old evolutionary conserved heritable trait of surviving environmental threats through exponential proliferation of mutant strains selected by Darwinian principle. Therefore, OAT success with minimal AMR can be ensured by antimicrobial stewardship (AMS) following the principle of 5Ds -drug, dose, duration, drug-route, and de-escalation. While convenient to administer, the onset of minimum inhibitory concentration (MIC) for OAT in urine is a window of opportunity for uropathogens to survive the first contact with OAT and the descendant colonies armed with AMR are likely to survive subsequent higher urine OAT levels. Meanwhile, intravesical antimicrobial treatment (IAT) delivers the first strike well above MIC. The root cause analysis of AMR dovetails with the strengths, weaknesses, opportunity, and threat (SWOT) analysis of OAT in this interdisciplinary review.

Limited availability of expensive alloying elements elevates low-alloyed steels to a unique position in the field of lightweight construction and mass production. Quenching and partitioning (Q&P) heat treatments of low-alloyed steels with exceptional property combinations are particularly promising. In this study, we characterize for the first time a new low-alloyed steel to be processed by Q&P heat treatments. In combined experimental and numerical studies, we design a novel approach that effectively combines the short cycle times of press hardening with the excellent property profiles of Q&P-treated steels. We identify appropriate transformation parameters for Q&P heat treatments by dilatometric studies and we adjust a number of reference conditions with different isothermal holding times. By means of SEM analysis and XRD measurements, we show that different fractions of retained austenite result in different mechanical properties. Initial numerical designs of the process can identify varying temperature profiles and cooling rates depending on the position in the die. The results show that the geometry of the part plays a minor role, but the die temperature is the dominant factor for successful partitioning directly in the press hardening process.

Biological function depends on the composition as well as structure of the organism, that is the organization of interactions between its parts. In multicellular organisms, the complex communication between cells is crucial for the coordination of cellular functions (growth, differentiation, apoptosis), compartmentalization of cellular processes within the organism, and the integration of cells into functioning higher levels of structural organization. Here we focus on the interaction among cells, as the basic level of biological organization, capable of a remarkable degree of autonomy and self-maintenance. While a wealth of data on putative cell interactions has recently become available, its biological interpretation depends on expectations we have for the structure of these interaction networks. This contribution is an attempt at formulating basic questions we may ask about cell interaction data. We build on the understanding that cells fulfill two general functions: the integrity-maintaining and the organismal service function. We derive the expected patterns of cell interactions considering two intertwined aspects: the immediate functional and the evolutionary. Based on these, we propose several guidelines for analysis and interpretation of transcriptional cell-interactome data.

A body plan is a stable configuration of characters for a major taxonomic group, such as chordates or arthropods. Despite widespread casual reliance on the concept for guiding comparisons within and between groups, the nature of body plans as well as the biological causes underlying their evolution have remained elusive. This paper proposes an abstract mechanistic model of body plan identity. We hypothesize that body plans are an evolutionary phenomenon that only applies to a relatively small subset of major clades, rather than being associated with each and every so-called “phylum.” Body plans arise in evolution by stepwise accretion, and require a level of developmental complexity that is only found in some animal clades. Further, we suggest that, parallel to the developmental mechanisms controlling character identity, there are “body plan identity mechanisms” (BpIMs) that maintain entire configurations of characters while possessing a mechanistic architecture that is itself stable and traceable through evolutionary change. These BpIMs, we suggest, are entrenched intercellular signaling networks operating between transient embryonic structures that are destined to differentiate into distinct individualized characters. The activity of a BpIM results in a transient long-range integration of the embryo that is highly sensitive to genetic and environmental perturbations, and that can be detected morphologically as a conserved phylotypic stage. This model is illustrated with detailed interpretations of the notochord signaling system and the segment polarity network as candidate BpIMs in vertebrates and arthropods, respectively. We conclude by contrasting the proposed developmental-mechanistic conception of body plans with the phylogenetic notion of ground plans, and sketch the general outlines of an empirical research program on body plan evolution.

Embryo implantation is a hallmark of the female reproductive biology of eutherian (placental) mammals and does not exist in a sustainable form in any other vertebrate group. Implantation is the initial process that leads to a sustained fetal-maternal unit engendering a complex functional relationship between the mother and the embryo/fetus. The nature of this relationship is often portrayed as one of conflict between an aggressive embryo and a passive or defensive maternal organism. Recent progress in elucidating the evolutionary origin of eutherian pregnancy leads to a different picture. The emerging scenario suggests that the very initial stages in the evolution of embryo implantation require evolutionary changes to the maternal physiology, which modified an ancestral generic mucosal inflammation in response to the presence of the embryo into an active embedding process. This “female-first” evolutionary scenario also explains the role of endometrial receptivity in human pregnancy. On the marsupial side, where in most animals the fetal-maternal interaction is short and does not lead to a long term sustainable placentation, the relationship is mutual. In these mammals uterine inflammation is followed by parturition in short order. The inflammatory signaling pathways, however, are cooperative, i.e. they are performed by both the fetus and the mother and therefore we call this relationship “cooperative inflammation.” Based on these discoveries we reconceive the narrative of the maternal-fetal relationship.

This paper presents a) the novel hybrid learning method to train the type-1 non-singleton interval type-3 (IT3) fuzzy logic systems (IT3 NSFLS-1) and b) the novel method named enhanced Wagner-Hagras (EWH) IT3 NSFLS-1 fuzzy systems which includes the level alpha 0 output to calculate the output y alpha using the average of the outputs y alpha k instead of their weighted average. The development of the proposed methodology uses the orthogonal least square (OLS) method to train the consequent parameters and the back propagation (BP) method to train the antecedent parameters. This proposal dynamically changes the parameters of only the level alpha 0 minimizing some criterion function as new information becomes available to each level alpha k. The antecedent sets are type-2 fuzzy sets, the consequent sets are fuzzy centroids, the inputs are type-1 non-singleton fuzzy numbers with uncertain standard deviations, and the secondary membership functions are modeled as two Gaussians with uncertain standard deviation and the same mean. Based on the firing set of the level alpha 0, the proposed methodology calculates each firing set of each level alpha k to dynamically construct and update the EWH IT3 NSFLS-1 (OLS-BP) system. The algorithm was tested in a hot strip mill facility to predict the transfer bar surface temperature showing its superior capability to obtain the industrial pyrometer’s knowledge uncertainty for tuning and its better performance when compared with IT2 SFLS, IT2 NSFLS-1, GT2 SFLS, GT2 NSFLS-1, IT3 SFLS, and IT3 NSFLS-1 trained with the BP-BP algorithm.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

A popular approach to learning about admixture from population genetic data is by computing the allele-sharing summary statistics known as f-statistics. Compared to some methods in population genetics, f-statistics are relatively simple, but interpreting them can still be complicated at times. In addition, f-statistics can be used to build admixture graphs (multi-population trees allowing for admixture events), which provide more explicit and thorough modeling capabilities but are correspondingly more complex to work with. Here, I discuss some of these issues to provide users of these tools with a basic guide for protocols and procedures. My focus is on the kinds of conclusions that can or cannot be drawn from the results of f₄-statistics and admixture graphs, illustrated with real-world examples involving human populations.

Despite the popularity of Zumba in several countries, research is scarce about its impact on older adults. Meanwhile, the integration of cognitive tasks with physical exercises, known as dual-tasking, is an evolving strategy to facilitate activities for older people. This study investigated the perceptions of older adults regarding Zumba and the potential of implementing it in a dual-task program. We conducted a qualitative-descriptive research involving 44 Filipino older adults from August to November 2020. Content analysis was employed to analyze the data. Four themes were identified: moving towards match or mismatch; balancing benefits with burdens; dual-tasking as innovative yet potentially challenging; and overcoming barriers with enablers. While Zumba is an inclusive and beneficial activity, individual and contextual limitations could hinder its suitability for older people. Dual-tasking in Zumba was also recognized as an innovative approach, although challenges should be addressed to promote its utility. Several strategies could support the design of these programs in communities. This is the first study to explore older adults’ perceptions towards Zumba and its potential utilization as a dual-tasking program. Findings could guide the implementation of appropriate Zumba and dual-tasking activities that seek to integrate cognitive and physical training for older adults.

This paper presents a comparison of two methods to represent variable blade inertia in two codes for aero-servo-elastic simulations of wind turbines: the nonlinear aeroelastic multi-body model HAWC2 and the nonlinear geometrically exact beam model BeamDyn for OpenFAST. The main goal is to enable these tools to simulate the dynamic behavior of a wind turbine with variable blade inertia. However, in order to simulate the structural response of wind turbines with variable blade inertias, the source code of load simulation tools need to be modified. This is due to the fact that, currently, state-of-the-art load simulation tools for wind turbines are unable to simulate variable rotor blade inertias. The validity of the modified codes is proven based on a simple beam model. The validation shows very good agreement between the modified codes of HAWC2, BeamDyn and an analytical calculation. The add-on of variable blade inertias is applied to reduce the mechanical loads of a 5 megawatt reference wind turbine with an integrated hydraulic-pneumatic flywheel in its rotor blades.

Age-related changes in behavior and sensory perception have been observed in a wide variety of animal species. In ants and other eusocial insects, workers often progress through an ordered sequence of olfactory-driven behavioral tasks. Notably, these behaviors are plastic, and workers adapt and rapidly switch tasks in response to changing environmental conditions. In the Florida carpenter ant, smaller minors typically perform most of the work needed to maintain the colony while the larger majors are specialized for nest defense and rarely engage in these routine tasks. Here, we investigate the effects of age and task group on olfactory responses to a series of odorant blends in minor and major worker castes. Consistent with their respective roles within the colony, we observed significant age-associated shifts in the olfactory responses of minors as they transitioned between behavioral states, whereas the responses of majors remained consistently low regardless of age. Furthermore, we identified a unitary compound, 3-methylindole, which elicited significantly higher responses and behavioral aversion in minor nurses than in similarly aged foragers suggesting that this compound may play an important role in brood care. Taken together, our results suggest that age- and task-associated shifts in olfactory physiology may play a critical role in the social organization of ant colonies.

The extent to which projects are established as an organizational form in society to cope with various challenges has been analyzed extensively in research under the term ‘projectification.’ However, it remains unclear how the projectification at the level of society begins and which actors are involved in its institutionalization. Drawing on an explanatory case study in post-Soviet Kyrgyzstan, responses are provided to these questions and propositions for further research. The country is undertaking reforms as part of its ongoing transformation, which includes professional implementation of projects, particularly in the public sector. These activities are, to some extent, based on the developments in project management in neighboring Kazakhstan, where a presidential decree also constituted a first step towards the institutionalization of projectification. It later found its way into relevant sectors and to key actors via the presidential administration, primarily through regulative and normative institutions. Due to increased international cooperation, the number and importance of projects in Kyrgyzstan will continue to increase in the coming years, requiring greater emphasis on projectification. The results are informative for research into projectification and for those involved in countries with comparable situations.

There is a continuous growth of heat pump installations in residential buildings in Germany. The heat pumps were not only used for space heating and domestic hot water consumption but also to offer flexibility to the grid. the high coefficient of performance and the low cost of heat storages made the heat pumps an optimal candidate for the power to heat applications. Thus, several questions are raised about the optimal integration and control of the heat pump system with buffer storages to maximize its operation efficiency and minimize the operation costs. In this paper, an experimental investigation is performed to study the performance of a ground source heat pump (GSHP) with a combi-storage under several configurations and control factors. The experiments were performed on an innovative modular testbed that is capable of emulating a ground source to provide the heat pump with different temperature levels at different times of the day. Moreover, it can emulate the different building loads such as the space heating load and the domestic hot water consumption in real-time. The data gathered from the testbed and different experimental studies were used to develop a simulation model based on Modelica that can accurately simulate the dynamics of a GSHP in a building. The model was validated based on different metrics. Energetically, the difference between the developed model and the measured values was only 3.08\% and 4.18\% for the heat generation and electricity consumption, respectively.

In this work, we explore a the different forms of a new type of modified gravity, namely f(φ) gravity. We construct the Big Rip type for the energy density and the curvature of the universe. We show that dark energy is a result of the transformation of the field φ mass (dark matter) to energy. In addition, we provide that Ω_{m}≈0,050, Ω_{DM}≈0,2, Ω_{DE}≈0,746, is in excellent agreement with observation data. We explore a generalized formalism of braneworld modified gravity. We also construct a new field equations, which generalize the Einstein field equations. We provide a relation between the extra dimension in 3-brane with the vacuum energy density. We show that the energy density of matter depends directly on the number of dimensions. We manage to find the value of the Gauss-Bonnet coupling α=1/4 which is a good agreement with the results in the literature, this correspondence creates a passage between f(R) gravity and Gauss-Bonnet gravity, this comparison leads to a number of bulk dimensions equal to D=10¹²¹+4.

In many application problems, F-transform algorithms are very efficient. In F-transform techniques, we replace the original signal or image with a finite number of weighted averages. The use of weighted average can be naturally explained, e.g., by the fact that this is what we get anyway when we measure the signal. However, most successful applications of F-transform have an additional not-so-easy-to-explain feature: the partition requirement, that the sum of all the related weighting functions is a constant. In this paper, we show that this seemingly difficult-to-explain requirement can also be naturally explained in signal-measuring terms: namely, this requirement can be derived from the natural desire to have all the signal values at different moments of time estimated with the same accuracy.

In this paper we have defined the effect of bulk viscosity on Quintessence model and scaler field potential as well as on classical field. We have shown the same effect for modified gravity with f(R,T)= R+f(T). In the derivation we have predicted the possibility of time dependent evolution of gravitational constant G and anisotropy.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

The compatibility between the de Sitter Swampland conjecture and Ho\v{r}ava-Lifshitz $F(\bar{R})$ theories with a flat FLRW metric is studied. We first study the standard $f(R)$ theories and show that the only way in which the dS conjecture can be made independent of $R$ is by considering a power law of the form $f(R)\sim R^{\gamma}$. The conjecture and the consistency of the theory puts restrictions on $\gamma$ to be greater but close to $1$. For the $F(\bar{R})$ theories described by its two parameters $\lambda$ and $\mu$ we use the equations of motion to construct the function starting with an ansatz for the scale factor in the Jordan frame of the power law form. By doing a conformal transformation on the three metric to the Einstein frame we can obtain an action of gravity plus a scalar filed by relating the parameters of the theory. The non-projectable and projectable cases are studied and the differences are outlined. The $F(\bar{R})$ function obtained consists of terms of the form $\bar{R}^{\gamma}$ with the possibility of having negative power terms. The dS conjecture leads to inequalities for the $\lambda$ parameter, in both versions it gets restricted to be greater but close to $1/3$. For the general case in which $\mu$ and $\lambda$ are considered as independent, the action contains an extra term but we propose that the conjecture is still applicable. Once again the non-projectable and projectable cases are studied. The $F$ function obtained has the same form as before, the consistency of the theory and the dS conjecture lead to a set of inequalities on both parameters that are studied numerically. In all cases $\lambda$ is restricted by $\mu$ around $1/3$ and we obtain $\lambda\to1/3$ if $\mu\to0$. Finally we consider the $f(R)$ limit $\mu,\lambda\to1$ and we obtain consistent results.

Fused deposition modeling (FDM) is a rather new technology in the production of personalized dosage forms. Melting and printing of polymer–active pharmaceutical ingredient (API) – mixtures can be used to produce oral dosage forms with different dosage as well as release behavior. This process is utilized to increase the bioavailability of pharmaceutically relevant active ingredients that are poorly soluble in physiological medium by transforming them into solid amorphous dispersions (ASD). Release from such ASDs is expected to be faster and higher compared to the raw materials and thus enhance bioavailability. Printing directly from powder while forming ASDs was realized. Different techniques to change release patterns as well as a non-destructive way for determination of API distribution were shown. By measuring the melt viscosities of mixtures printed a rheological model for the printer used is proposed.

We study the μ-μ45-T phase diagram of the 2+1-dimensional Gross-Neveu model, where μ denotes the ordinary chemical potential, μ45 the chiral chemical potential and T the temperature. We use the mean-field approximation and two different lattice regularizations with naive chiral fermions. An inhomogeneous phase at finite lattice spacing is found for one of the two regularizations. Our results suggest that there is no inhomogeneous phase in the continuum limit. We show that a chiral chemical potential is equivalent to an isospin chemical potential. Thus, all results presented in this work can also be interpreted in the context of isospin imbalance.

We investigate alternative candidates to dark energy that can explain the current state of the universe in the framework of the generalized teleparallel theory of gravity f(T ) where T denotes the torsion scalar. To achieve this, we carried out a series of reconstruction taking into account to the ordinary and entropy-corrected versions of the holographic and new agegraphic dark energy models. These models used as alternative to dark energy in the literature in order describe the current state of our universe. It is remarked that the models reconstructed indicates behaviors like phantom or quintessence models. Furthermore, we also generated the EoS parameters associated to entropy-corrected models and we observed a transition phase between quintessence state and phantom state as showed by recent observational data. We also investigated on the stability theses models and we created the {r − s}. The behavior of certains physical parameters as speed of sound and the Statefinder parameters are compatible with current observational data.

In this work we present a novel steganography algorithm, based on Fractal Transform domain, combined with the principles of Cryptography. The proposed method uses a private key, which will indicate which segment of the image will be taken and encoded with the Fractal Transform, to then insert the secret bits in the transformed coefficients, thus generating the stego image.

Advanced manufacturing techniques, aimed at implants with high dependability, flexibility, and low manufacturing costs, are crucial in meeting the growing demand for high-quality products like biomedical implants. Incremental sheet forming is a promising flexible manufacturing approach for rapidly prototyping sheet metal components using low-cost tools. Titanium and its alloys are used to shape most biomedical implants because of its superior mechanical qualities, biocompatibility, low weight, and great structural strength. The poor formability of titanium sheets at room temperature, however, limits their widespread use. The goal of this research is to show that gradual sheet formation of a titanium biomedical implant is possible. The possibility of creative and cost-effective concepts for the manufacturing of such complicated shapes with significant wall angles is explored in this study. A numerical simulation based on finite element modeling as well as a design process tailored to metal forming is used to complete the development. The mean of uniaxial tensile tests with a constant strain rate was used to study the flow behavior of the studied material. To forecast the crack, the obtained flow behavior was modeled using the behavior model and failure model.

In the Brazilian Amazon, rural settlements are increasingly isolated by large-scale production farms, jeopardizing their sustainability and the good living of family farmers. Works were carried out in settlements to measure sustainability. However, the majority does not consider the participation and the collectively of those involved. In this way, we propose to evaluate, in a collective and participatory way, the sustainability and good living of the SDP São Paulo Rural Settlement, of the northern Amazon of Mato Grosso. We used the didactic-pedagogical method Circle of Sustainability, developed from five points: 1st - circle of investigation of generating themes; 2nd - circle of the history of the subject world; 3rd - circle of diagnosis of rural settlements; 4th - circle of exchange of knowledge; and 5th - circle of sustainable perceptions and narratives. The historical, socioeconomic and cultural characterization of the settlement allowed us to understand how sustainability and good living are being built in the settlement history process. Sustainability and good living are dialectical processes, are under construction, in movement.

Scanning magnetic microscopy is a new tool that has recently been used to map magnetic fields with good spatial resolution and field sensitivity. This technology has great advantages over other instruments; for example, its operation does not require cryogenic technology, which reduces its operational cost and complexity. Here, we describe the construction of a customizing scanning magnetic microscope based on commercial Hall-effect sensors at room temperature that achieves a spatial resolution of 200 µm. Two scanning stages on the x- and y-axes of precision, consisting of two coupled actuators, control the position of the sample, and this microscope can operate inside or outside a magnetic shield. We obtained magnetic field sensitivities better than 521 nT_rms/√Hz between 1 and 10 Hz, which correspond to a magnetic momentum sensitivity of 9.20 × 10^–10 Am². In order to demonstrate the capability of the microscopy, polished thin sections of geological samples, samples containing microparticles and magnetic nanoparticles were measured. For the geological samples, a theoretical model was adapted from the magnetic maps obtained by the equipment. Vector field maps are valuable tools for the magnetic interpretation of samples with a high spatial variability of magnetization. These maps can provide comprehensive information regarding the spatial distribution of magnetic carriers. In addition, this model may be useful for characterizing isolated areas over samples or investigating the spatial magnetization distribution of bulk samples at the micro and millimeter scales. As an auxiliary technique, a magnetic sweep map was created using Raman spectroscopy; this map allowed the verification of different minerals in the samples. This equipment can be useful for many applications that require samples that need to be mapped without a magnetic field at room temperature, including rock magnetism, the nondestructive testing of steel materials and the testing of biological samples. The equipment can not only be used in cutting-edge research but also serve as a teaching tool to introduce undergraduate, master's and Ph.D. students to the measurement methods and processing techniques used in scanning magnetic microscopy.

This paper describes the design and implementation of an ultrasonic non-contact air-coupled technique (UNCACT) using antisymmetric Lamb waves (ALW) for NDT assessment in novel composite sandwich plates of the car body shell. This technique is complemented with a C-Scan image implementation using this kind of guided waves. The finite element method using Comsol 6.1 is developed for the interpretation of the several wave modes presented in the experiments, including the ALW mode. The phase velocity method (PVM) is applied for the verification of the ALW mode in the portion of the RF signal necessary in the C-Scan image.

French Guiana, located in the Guiana Shield, is a natural reservoir for many zoonotic pathogens that are of considerable medical or veterinary importance. Until now, there are few data available on the description of parasites circulating in this area, especially on protozoan belonging to the phy-lum Apicomplexa; conversely, the neighbouring countries describe a high parasitic prevalence in animals and humans. Epidemiological surveillance is necessary, as new potentially virulent strains may emerge from these forest ecosystems, such as Amazonian toxoplasmosis. However, there is no standard tool for detecting protozoa in wildlife. In this study, we developed Meat-Borne-Parasite, a high-throughput meta-barcoding workflow for detecting Apicomplexa based on Oxford Nanopore Technologies sequencing platform using the 18S gene of fourteen Apicomplexa-positive samples collected in French Guiana. Sequencing reads were then analysed with MetONTIIME pipeline. Thanks to a scoring rule, we were able to classify as Apicom-plexa-positive 10 samples out of 14 and reveal the presence of co-carriages. The same samples were also sequenced with Illumina platform, for validation purposes. On samples identified as Apicomplexa-positive by both platforms, a strong positive correlation at up to genus level was reported. Overall, the presented workflow represents a reliable method for Apicomplexa detec-tion, which may pave the way for more comprehensive biomonitoring of zoonotic pathogens.

Previous reviews have investigated machine learning (ML) models used to predict the risk of developing preeclampsia but have not described how the ML models are intended to be deployed throughout pregnancy or feature performance. The aim of this study is to provide an overview of the existing ML models and their intended deployment patterns and performance along with identified features of high importance. This review used the Preferred Reporting Items for Systematic Reviews and Meta-Analyses 2020 guidelines. PubMed, Engineering Village, and the Association for Computing Machinery were searched between January and February 2024. A total of 86 studies were found of which 14 were included. Out of 12 studies, eight showed the intent to use the ML model as a single-use, two intended a dual-use, and two intended multiple-use. A total of seven studies listed the features of the highest importance. Systolic and diastolic blood pressure were listed along with mean arterial pressure to be of high importance. Out of four studies intending to use the ML model more than a single-use, three of them were conducted in the years 2023 and 2024, whereas the remaining study is from 2011. No ML model emerged as superior across the subgroups of PE. Utilizing body mass index and either mean arterial pressure or diastolic blood pressure and systolic blood pressure may benefit the performance. The deployment patterns are mainly single use being within the gestation weeks 11+0 to 14+1.

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

Recent studies have demonstrated an important role for vitamin C in the epigenetic regulation of cancer-related genes via DNA demethylation by the ten-eleven translocation (TET) methylcytosine dioxygenase enzymes. DNA methyltransferase (DNMT) reverses this, increasing DNA methylation and decreasing gene expression. Dual oxidase (DUOX) enzymes produce hydrogen peroxide (H2O2) in normal pancreatic tissue but are silenced in pancreatic cancer (PDAC). Treatment of PDAC with pharmacologic ascorbate (P-AscH-, intravenous, high dose vitamin C) increases DUOX expression. We hypothesized that inhibiting DNMT may act synergistically with P-AscH- to further increase DUOX expression and cytotoxicity of PDAC. PDAC cells demonstrated dose-dependent increases in DUOX mRNA and protein expression when treated with DNMT inhibitors. PDAC cells treated with P-AscH- + DNMT inhibitors demonstrated increased DUOX expression, increased intracellular oxidation, and increased cytotoxicity in vitro and in vivo compared to either treatment alone. These findings suggest a potential therapeutic, epigenetic mechanism to treat PDAC.

Conversational spoken dialogue systems that interact with the user rather than merely reading text can be equipped with hesitations to manage the dialogue flow and the users' attention. Based on a series of empirical studies, we built an elaborated hesitation synthesis strategy for dialogue systems that inserts hesitations of scalable extent wherever needed in the ongoing utterance. So far, evaluations of hesitating systems have shown that synthesis quality is affected negatively by hesitations, but that there is improvement in interaction quality. We argue that due to its conversational nature, hesitation synthesis needs interactive evaluation rather than traditional MOS-based questionnaires. To prove this point, we dually evaluate our system’s speech synthesis component: on the one hand, linked to the dialogue system evaluation, on the other hand, in the traditional MOS way. This way we are able to analyze and discuss differences that arise due to the evaluation methodology. Our results suggest that MOS scales are not sufficient to assess speech synthesis quality, which has implications for future research that are discussed in this paper. Furthermore, our results indicate that hesitations work well to increase task performance and that an elaborated strategy is necessary to avoid likability issues.

Keywords: Marine Coasts; Protected Areas; Defense and Conservation; Asbestos Cement Materials; Wastes; Contamination; Human Health Risk; Medical Geology.

Here are given tight probabilistic inequalities that provide nearly best estimates for the Csiszar's f-divergence. These use the right and left psi -Hilfer fractional derivatives of the directing function f. Csiszar's f- divergence or the so called Csiszar's discrimination is used as a measure of dependence between two random variables which is a very essential aspect of stochastics, we apply our results there. The Csiszar's discrimination is the most important and general measure for the comparison between two probability measures. We give also other applications.

Human urinary bladder cancer has similar development that invasive urothelial cancer that happens spontaneously in dogs. Then, research of these malignant tumors associated with the advances of new treatment drive to the specific fight of the urothelial tumor cell, is highly valuably related to efficiency and reduction of side effects of treatments, even extrapolating to humans. Thus, a review of the most important aspects on new advances on canine bladder cancer was achieved. Many forms of therapies are being reported; one of them, of highly promising feature is the treatment with immunomodulators. The resemblance between spontaneous urothelial cancer in canines and urinary bladder cancer in humans makes this canine tumor relevant animal model to research and advances of treatment that may be more efficient in management of tumor with less unfavorable effects. Immunomodulators exhibit important outcomes when used in the therapy of bladder cancer in dogs. Nanomaterials that are possible carriers of some kinds of drugs to the target tumor significantly raise the efficiently of the therapy. Therefore, the advancement of immunomodulator combined with nanoparticles can disrupt the therapy of bladder cancer in dogs and thereafter in humans.

Although all isolates of the foodborne pathogen Listeria monocytogenes are considered to be pathogenic, epidemiological evidence indicates that certain serovar 4b lineages are more likely to cause severe invasive (neuromeningeal, maternal-fetal) listeriosis. Recently described as L. monocytogenes “hypervirulent” clones, no distinctive bacterial trait has been identified so far that could account for the differential pathogenicity of these strains. Here we discuss some preliminary observations in experimentally infected mice suggesting that serovar 4b hypervirulent strains may have a hitherto unrecognized capacity for prolonged in vivo survival. We propose the hypothesis that protracted survivability in primary infection foci in liver and spleen –first target organs after intestinal translocation– may cause L. monocytogenes serovar 4b hypervirulent clones to have a higher probability of secondary dissemination to brain and placenta.

Development of accelerometer-based lameness (mobility) detection has focused on cow behaviors such as lying and walking. Several studies, usually small, have reported levels of accuracy up to 91%. However, there has been limited independent replication of these results. In this study, behavior measures previously identified as being associated with lameness such as lying bouts and walking time are examined in relation to mobility score. On a research farm and a commercial farm, four trials were completed with 65 grazing cows. The cows had differing mobility scores ranging from perfect mobility to impaired mobility. Behavior was monitored using leg worn accelerometers. In general, behavior and mobility associations identified in previous studies were not found. Behavior monitoring with accelerometers as a basis to classify impaired mobility in pasture-based contexts thus remains challenging.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

Myocarditis has been recognized as a possible rare complication of COVID-19 mRNA vaccination. It concerns between one and five vaccinated people per 100,000 in the general population, with increased incidence in adolescent and young adult men. Most often, cases of myocarditis have been reported in the days following the second dose of vaccine mainly in younger male patients. This rare complication of vaccination usually resolves within days or weeks. However, the pathophysiological events responsible for the increase in frequency of myocarditis after COVID-19 vaccination remain unclear. Several recent reports have highlighted that free spike proteins circulating in the blood of patients at high levels appear to play a major role in myocarditis. Here, we review the most relevant data that partly lift the veil on the molecular mechanisms of the induction of myocarditis following mRNA-based COVID-19 vaccination. We hypothesize that a mechanism of molecular mimicry of the viral spike triggers transient dysregulation of angiotensin-converting enzyme 2, leading to increased soluble angiotensin II binding to the transmembrane receptor angiotensin II type I receptor, similar to what is observed during SARS-CoV-2 infection. We suggest to standardize management of suspected cases of mRNA-based COVID-19 vaccine-induced myocarditis, including angiotensin II and spike antigenemia monitoring.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

We study the efficient computation of power indices for weighted voting games with precoalitions amongst subsets of players (reflecting, e.g., ideological proximity) using the paradigm of dynamic programming. Starting from the state-of-the-art algorithms for computing the Banzhaf and Shapley-Shubik indices for weighted voting games we present a framework for fast algorithms for the three most common power indices with precoalitions, i.e. the Owen index, the Banzhaf-Owen index and the Symmetric Coalitional Banzhaf index, and point out why our new algorithms are applicable for large numbers of players. We discuss implementations of our algorithms for the three power indices with precoalitions in C++ and review computing times as well as storage requirements.

Understanding the evolutionary role of environmentally-induced phenotypic variation (i.e., environmental plasticity) is an important issue in developmental evolution. One of the major physiological responses to environmental changes is cellular stress, which is counteracted by a generic stress reaction that detoxifies the cell, refolds proteins, and repairs DNA damage. In this paper, we elaborate on a previous finding suggesting that the cell differentiation cascade of human decidual stromal cells, a cell type critical for embryo implantation and the maintenance of pregnancy, evolved from a cellular stress reaction. We hypothesize that the stress reaction in these cells was elicited ancestrally through the inflammation caused by embryo attachment and invasion. We describe a model, Stress-Induced Evolutionary Innovation (SIEI), whereby ancestral stress reactions and their corresponding pathways can be transformed into novel structural components of body plans, such as new cell types. After reviewing similarities and differences between SIEI and the “plasticity first hypothesis” (PFH) of evolution, we argue that SIEI is a distinct form of plasticity-based evolutionary change because it leads to the origin of novel structures rather than the adaptive transformation of a pre-existing character.

Solar power innately has issues with weather, grid demand and time of day, which for the case of concentrating solar power (CSP) can be mitigated through use of thermal energy storage. Nuclear reactors, including lead-cooled fast reactors (LFRs), can load follow, but have high fixed and low operating costs which can make this economically unattractive. We investigate potential synergies through coupling CSP and LFR together in a single supercritical CO$_2$ Brayton cycle and/or using the same thermal energy storage. Combining these cycles allows for the LFR to thermally charge the salt storage in the CSP cycle during low demand periods to be dispatched when grid demand increases. The LFR/CSP coupling into one cycle is modeled to find the preferred location of the LFR heat exchanger, CSP heat exchanger, sCO$_2$-to-salt heat exchanger (C2S), turbines, and recuperators within the supercritical CO$_2$ Brayton cycle. Three cycle configurations have been studied: two-cycle configuration, which uses CSP and LFR heat for dedicated turbocompressors, has the highest efficiencies but with less component synergies; a combined cycle with CSP and LFR heat sources in parallel is the simplest with the lowest efficiencies; and a combined cycle with separate high temperature recuperators for both the CSP and LFR is a compromise between efficiency and component synergies. Additionally, four thermal energy storage charging techniques are studied: the turbine positioned before C2S, requiring a high LFR outlet temperature for viability; the turbine after the C2S, reducing turbine inlet temperature and therefore power; the turbine parallel to the C2S producing moderate efficiency; and a dedicated circulator loop. While all configurations have pros and cons, use of a single cycle offers component synergies with limited efficiency penalty. Using a turbine in parallel with the C2S heat exchanger is feasible but results in a low charging efficiency, while a dedicated circulator loop offers flexibility and near perfect heat storage efficiency but increasing cost with additional cycle components.

Condition monitoring of bearings is an open issue. The use of the stator current to monitor induction motors has been validated as a very advantageous and practical way to detect several types of faults. Nevertheless, for bearing faults the use of vibrations or sound generally offers better results in the accuracy of the detection although with some disadvantages related to the sensors used for monitoring. To improve the performance of bearing monitoring, it is proposed to take advantage of more information available in the current spectra, beyond the usually employed, incorporating the amplitude of a significant number of sidebands around the first eleven harmonics, growing exponentially the number of fault signatures. This is especially interesting for inverter-fed motors. But, in turn, this leads to the problem of overfitting when applying a classifier to perform the fault diagnosis. To overcome this problem, and still exploit all the useful information available in the spectra, it is proposed to use shrinkage methods, which have been lately proposed in machine learning to solve the overfitting issue when the problem has much more variables than examples to classify. A case study with a motor is shown to prove the validity of the proposal

This work explores the use of Kuhn verdazyl radicals as building blocks in multifunctional molecular materials in an exemplary study, focusing on the magnetic and the electron transfer (ET) characteristics, but also addressing the question whether chemical modification by cross-coupling is possible. The ET in solution is studied spectroscopically whereas solid state measurements afford information about the magnetic susceptibility or the conductivity of the given samples. The observed results are rationalized based on the chemical structures of the molecules, which have been obtained by X-ray crystallography. The crystallographically observed molecular structures as well as the interpretation based on the spectroscopic and physical measurements are backed up by DFT calculations. The measurements indicate that only weak, antiferromagnetic coupling is observed in Kuhn verdazyls owed to the low tendency to form face-to-face stacks, but also that steric reasons alone are not sufficient to explain this behavior. Furthermore, it is also demonstrated that ET reactions proceed rapidly in verdazyls/verdazylium redox couples and that Kuhn verdazyls are suited as donor molecules in ET reactions.

A Friedmann-Lemaitre-Robertson-Walker space-time model with all curvatures k=0,±1 is explored in f(R,T) gravity. The solutions are obtained via the parametrization of the scale factor that leads to a model transiting from a decelerated universe to an accelerating one. The physical features of the model are discussed and analysed.

We analyze the behavior of relativistic spherical objects within the context of modified $f(R,T)$ gravity considering Tolman VI spacetime, where gravitational lagrangian is a function of Ricci scalar(R) and trace of energy momentum tensor(T) i.e,$ f(R,T)= R+ 2\beta T$, for some arbitrary constant $\beta$. For developing our model, we have chosen $\pounds_{m} = -p$, where $ \pounds_{m}$ represents matter lagrangian. For this investigation, we have chosen three compact stars namely PSR J1614-2230 [Mass=(1.97$\pm$ 0.4)M$_\odot$; Radius= 9.69$_{-0.02} ^{+0.02}$ Km] ,Vela X-1 [Mass=(1.77$\pm$ 0.08)M$_\odot$; Radius= 9.560$_{-0.08} ^{+0.08}$ Km] and 4U 1538-52 [Mass=(9.69)M$_\odot$; Radius= 1.97 Km]. In this theory the equation of pressure isotropy is identical to standard Einstein's theory. So all known metric potential solving Einstein's equations are also valid here. In this paper, we have investigated the effort of coupling parameter ($\beta$) on the local matter distribution. Sound of speed and adiabatic index are higher with grater values of $\beta$ while on contrary mass function and gravitational redshift are lower with higher values of $\beta$ . For supporting the theoretical results, graphical representation are also employed to analyze the physical viability of the compact stars.

The ability of S. aureus to infect humans and cause a wide range of infections so efficiently is a consequence of the many variant virulence factors that it can produce. Superantigens (SAgs) make up a group of them and include staphylococcal enterotoxins (SE). The main objective of this study was to detect enterotoxin gene cluster (EGC) in S. aureus isolates that caused infections in Paraguayan children in the year 2017, through an observational and cross-sectional study. The detection of the EGC including the seg, sei, sem, sen, seo, and seu genes, was carried out by end-point PCR. 181 S. aureus isolates were collected, most of them caused skin and soft tissue infections (SSTI, n=140, 77%) and came from children under 6 years 50% (n=90). At least one SE gene was detected in 96% (174/181) of isolates and 24% (44/181) carried the entire EGC. An association between methicillin resistance and seg, sei, seo, and seu gene carriage (p ≤0.05) was observed. A high prevalence of EGC was detected in S. aureus isolates collected from infected children attending the main health care centers in Paraguay, its importance is due to the potential of these toxins to aggravate staphylococcal infections.

Gliomas are solid tumors of the Central Nervous System (CNS) that originated from different glial cells. The World Health Organization (WHO) classified these tumors into four groups (I-IV) with increasing malignancy. Glioblastoma (GBM) is the most common and aggressive type of brain tumor classified as a grade IV. GBM are resistant to conventional therapies with poor prognosis after diagnosis even when the Stupp protocol that combines surgery and radiochemotherapy is applied. Nowadays, few novel therapeutic strategies have been used to improve GBM treatment, looking for higher efficiency and lower side effects, but with relatively modest results. The circadian timing system temporally organizes the physiology and behavior of most organisms and daily regulates several cellular processes in organs, tissues, and even in individual cells, including tumor cells. The potentiality of the function of the circadian clock on cancer cells modulation as a new target for novel treatments with a chronobiological basis offers a different challenge that needs to be considered in further detail. The present review will discuss state of the art regarding GBM biology, the role of the circadian clock in tumor progression, and new chrono-chemotherapeutic strategies applied for GBM treatment.

In this work, we introduce a new concepts for $\alpha$-type $F$-Suzuki contraction and $\alpha$-type $F$-weak-Suzuki contraction in the context of $b$-metric spaces. Compared to the $\alpha$-type $F$-contraction and $F$-Suzuki contraction mappings, these contractions are essentially weaker. For these type of contraction mappings, sufficient conditions are established for the fixed point's existence and uniqueness in $b$-metric spaces. As a result, the findings encompass several generalizations. To show the usability of our obtained results, we provide a supportive example and an application to a non-linear differential equation with fractional order.

Healthcare professionals constantly face situations that reflect ecosystems’ degradation. These can negatively affect their mental health. Research suggests that hope and resilience can play an important role in this scenario, since they are related to/predict mental health in highly heterogeneous samples (considering geography, age, profession, health, etc.). In this context, the aims of the present study are: to characterize and explore the relationship between hope, resilient coping and mental health of Portuguese healthcare professionals. Using Google Forms, 276 healthcare professionals answered to the GHQ-28, the (adult) Trait Hope Scale, and the Brief Resilient Coping Scale (cross-sectional study). The minimum and maximum possible scores were reached, with the exception of the maximum score of GHQ-28-Total. Regarding Hope, 19.6% scored below the midpoint (M=43.46, SD=11.97); 29.3% revealed low resilience (M=14.93, SD=4.05); and the average of 4 of the 5 Mental Health scores (exception: Severe Depression) indicates the probability of a psychiatric case. Hope correlated with Social Dysfunction and GHQ-28-Total; resilient coping proved to be a (weak) predictor of 4 of the 5 GHQ-28 indicators (exception: Severe depression). The results support the need to promote the sample's mental health, hope and resilient coping. They also suggest that stimulating resilient coping may contribute to improving healthcare professionals’ mental health.

Decoherence with recurrences appear in the dynamics of the one-body density matrix of an $F = 1$ spinor Bose-Einstein condensate, initially prepared in coherent states, in the presence of an external uniform magnetic field and within the single mode approximation. The phenomenon emerges as a many-body effect of the interplay of the quadratic Zeeman effect, that breaks the rotational symmetry, and the spin-spin interactions. By performing full quantum diagonalizations very accurate time evolution of large condensates are analyzed, leading to heuristic analytic expressions for the time dependence of the density matrix, in the weak and strong interacting regimes. We are able to find accurate analytical expressions for both the decoherence and the recurrence times, in terms of the number of atoms and strength parameters, that show remarkable differences depending on the strength of the spin-spin interactions. We discuss the nature of these limits in the light of the thermodynamic limit.

The advances mobile communications has seen in recent years has rendered the radio spectrum a limited and, hence, an expensive resource. Therefore, technologies that support unlicensed access to spectrum are needed. Therefore, the adoption of novel modulation schemes becomes of utmost importance to obtain better spectral-localization and reduce the OOBE (\textit{Out of Band Emission}) inherent to OFDM (\textit{Orthogonal Frequency Division Multiplexing}) and, consequently, mitigating the interference between secondary (\textit{unlicensed}) and primary users. In this scenario, we assess the gain in the bit error probability using f-OFDM (\textit{filtered-OFDM}) in MIMO systems, both used in the 5G RANGE project.

Both types of surgical guides – with and without metal sleeves are founded beneficial in clinical studies. The aim of this in vitro study was to compare time of surgical procedure in dental implantology depending of used type of the surgical guide. Ten three dimensional (3D) printed models of lower jaws were prepared based on complete virtual model of patient clinical conditions with missing teeth 37, 46 and 47. Five of this models were used for implant sites preparation performed with use of surgical guide without metal sleeves and dedicated surgical kit, and next five were used for the same procedure performed with surgical guide with metal sleeves and dedicated surgical kit. Time of implant site preparation were measured and noted. Statistical analysis was performed using Student’s t test for independent samples. Difference of time in both groups were founded as statistically significant (t=-9.94; df =28; p=0.0000). Type of surgical guide is important factor which can impact on time of implant site preparation and all surgical procedure.

It has been proven that in standard Einstein gravity, exotic matter (i.e. matter violating the point-wise and averaged weak and null energy conditions) is required to stabilize traversable wormholes. Quantum field theory permits these violations due to the quantum coherent effects found in any quantum field . Even reasonable classical scalar fields violate the energy conditions. In the case of the Casimir effect and squeezed vacuum states, these violations have been experimentally proven. It is advantageous to investigate methods of minimizing the use of exotic matter. One such area of interest is extended theories of Einstein gravity. It has been claimed that in some extended theories, stable traversable wormholes solutions can be found without the use of exotic matter. There are many extended theories of gravity and in this review paper we first explore f(R) theories and then explore some wormhole solutions in f(R) theories including Lovelock gravity.

In this paper, we classify the function space of all real-valued functions on R denoted as F(R,R) into 28 distinct blocks. Each block contains elements that share common features in terms of the cardinality of their sets of continuity and differentiability. Alongside this classification, we introduce the concept of the Connection, which reveals a special relationship structure between four well-known real-valued functions in real analysis: the Cantor function, Dirichlet function, the Thomae function, and the Weierstrass function. Despite the significance of this field, several perspectives remain unexplored.

A locally-rotationally-symmetric Bianchi-I model filled with strange quark matter (SQM) is explored in f(R, T) gravity. We take f(R, T) = R + 2 f(T) = R + 2λT, where R is the Ricci scalar, T is the trace of energy-momentum tensor and λ is an arbitrary constant. Exact solutions are obtained by assuming that the expansion scalar is proportional to the shear scalar. This yields a constant value for the deceleration parameter, q = 2, which corresponds to the decelerated phase of the universe. The model is found to be physically viable for λ < −1. SQM during early evolution mimics ultra-relativistic radiation whereas at late times, it behaves as dust, quintessence or even the cosmological constant depending on the value of λ. The effective matter acts as a stiff fluid irrespective of the matter content and of the f(R, T) terms. The model is shear free at late times but remains anisotropic throughout the evolution. In the absence of the f(R, T) terms, SQM accelerates the universe. In the specific case when SQM vanishes at late times, the effect of f(R, T) is to accelerate the universe. The model admits the possibility that SQM could be an alternative to dark energy.

We obtain exact solutions to the field equations for 5 dimensional LRS Bianchi type-I spacetime in $f(R,T)$ theory of gravity where specifically the following three cases are considered: (i) $f(R,T)=\mu(R+T)$, (ii) $f(R,T)=R \mu + R T \mu^2$ and (iii) $f(R,T)=R+\mu R^2+\mu T$ where $R$ and $T$ respectively the Ricci scalar and trace of the energy-momentum tensor. It is found that the equation of state (EOS) parameter $w$ is governed by the parameter $\mu$ involved in the $f(R,T)$ expressions. We fine-tune the parameter $\mu$ to obtain effect of phantom energy in the model, however we also restrict this parameter to obtain a stable model of the universe. It is noted that the model isotropizes at finite cosmic time.

In this work, we study the existence of strange star in the background of f(T,T) gravity in the Einstein spacetime geometry, where T is the torsion tensor and T is the trace of the energy-momentum tensor. The equations of motion are derived for anisotropic pressure within the spherically symmetric strange star. We explore the physical features like energy conditions, mass-radius relations, modified TOV equations, principal of causality, adiabatic index, redshift and stability analysis of our model. These features are realistic and appealing to further investigation of properties of compact objects in f(T,T) gravity as well as their observational signatures.

In this study, we introduce the concept and construction of an innovative Digital Miniature Cathode Ray Magnetometer designed for the precise detection of magnetic fields. This device addresses several limitations inherent to magnetic probes such as D.C. offset, nonlinearity, temperature drift, sensor aging, and the need for frequent recalibration, while capable of oper-ating in a wide range of magnetic fields. The core principle of this device involves the utilization of a charged particle beam as the sensitivity medium. The system leverages the interaction of an electron beam with a scintillator material, which, then, emits visible light that is captured by an imager. The emitted scintillation light is captured by a CMOS sensor. This sensor not only rec-ords the scintillation light but also accurately determines the position of the electron beam, providing invaluable spatial information crucial for magnetic field mapping. The key innova-tion lies in the combination of electron beam projection, CMOS imager scintillation-based de-tection and digital image signal processing. By employing this synergy, the magnetometer achieves remarkable accuracy, sensitivity and dynamic range. The precise position registration enabled by the CMOS sensor further enhances the device's utility in capturing complex magnetic field patterns, allowing for 2D field mapping. In this work, the optimization of the probe's per-formance is tailored for applications related to the characterization of insertion devices in light sources, including undulators.

Antioxidants reduce arterial stiffness but the effects previously reported are weak. The present study evaluated the effects of 2 weeks of therapy with a combination of antioxidants (l-cysteine, thiamine, pyridoxine and ascorbic acid) compared to placebo on stiffness index (SI) a measure of arterial stiffness that is strongly correlated with central pulse wave velocity (PWV), using a Pulse Trace recorder in a diverse group of 78 volunteers. SI fell by 1.7 m/sec relative to placebo (95% confidence intervals 0.6 to 2.7 m/sec), a reduction of 19% (95% confidence intervals 9% to 31%). The Glass effect size was 1.4, indicating a very strong treatment effect which was substantially greater than found in previous studies of the effects of antioxidant therapy on arterial stiffness. The magnitude of reduction in SI was positively correlated with increasing age (r = 0.362 P = 0.02). The change in RI, a measure of compliance of small to medium size arteries, did not differ between the antioxidant and placebo groups The combination of antioxidants studied reduced PWV to a much greater extent than reported for other antioxidants. This combination may be of value in the treatment of cardiovascular disease.

Introduction: Substance-induced psychotic disorder (SIPD) is a mental health condition linked to the use of a psychotropic substance whose pathogenesis has not been totally clarified. The present retrospective observational study has the objective to identify differences in clinical features and peripheral biomarkers in SIPD patients according to the main substance of abuse.Methods: A total sample of 218 patients was divided in 3 groups according to the type of consumed substance: alcohol, cannabis and psychostimulants. The 3 groups were compared for continuous variables by one-way analyses of variance (ANOVAs) and for qualitative variables by χ² tests. After removing alcohol-induced psychotic disorder group, the same analyses were repeated. Statistically significant variables from these latter analyses were included in a binary logistic regression model to confirm their reliability as predictors for cannabis- or psychostimulants-induced psychotic disorders. Results: Psychotic cannabis abusers were younger (p<0.01) and had an earlier age at onset (p<0.01). On the contrary, alcohol consumers resulted to have a longer duration of illness (p<0.01), more previous hospitalizations (p=0.04), more frequent medical comorbidity (p<0.01), higher mean Modified Sad Person Scale scores (p<0.01). Finally, psychostimulant abusers had more frequently a lifetime history of poly-substance use disorders (p<0.01). Binary logistic regression revealed that higher mean Brief Psychiatric Rating Scale scores (p<0.01) higher sodium (p=0.012) and haemoglobin(p=0.040) plasma levels were predictors of cannabis misuse in SIPD patients.Conclusions: Different clinical factors and biochemical parameters con be associated to SIPD according to the main substance of abuse, thus requiring a specific management by clinicians.

Submerged aquatic vegetation, also referred to as submerged macrophytes, provides important habitats and serves as a significant ecological indicator for assessing the condition of water bodies and for gaining insights into the impacts of climate change. In this study, we introduce a novel approach for the extensive monitoring of submerged vegetation, validated against established monitoring techniques. Employing full waveform airborne laser scanning, frequently used for topographic mapping and forestry applications on dry land, we extend its application to the detection of underwater vegetation in Lake Constance. The primary focus of this research lies in the automatic classification of LiDAR (Light Detection And Ranging) point clouds, distinguishing the three vegetation classes (i) Low Vegetation, (ii) High Vegetation, and (iii) Vegetation Canopy based on their height. The results reveal detailed three-dimensional representation of submerged vegetation, enabling the identification of vegetation structures and inference of vegetation types with reference to pre-existing knowledge. While the results within training areas demonstrate high precision and alignment with comparative data, the findings in test areas exhibit comprehensible deficiencies that are likely addressable through corrective measures in the future.

Background and Objectives:: Hip osteoarthritis is the main cause physical disability, also has a serious impact on the efficiency and independence of older people. The aim of the study was to analyze the relationship between hip osteoarthritis and the risk of sarcopenia. Our main hypothesis was whether the risk of sarcopenia, as measured by the SARC F questionnaire , is related to the physical fitness of older people with hip osteoarthritis. Materials and Methods: The study was conducted with the participation of 177 people of aged 65 or more, diagnosed hip osteoarthritis. The subjects were assessed using the SARC F questionnaire, the Short Physical Performance Battery (SPPB) and Timed Up and Go (TUG) test. The subjects were divided into two groups depending on the result they obtained in the SARC F questionnaire (group 1- SARC F &lt;4, group 2 - SARC F ≥ 4). Results: There was a significant correlation between the results in the SARC F and the results of the TUG (p&lt;0.001) and the SPPB test, both the SPPB total score (p&lt;0.001)and its elements: SBBP chair stand test (p&lt;0.001), SPPB balance test (p&lt;0.001), SPPB gait speed test (p&lt;0.001). Logistic regression of the SPPB and TUG predictors showed that in SARC F more than 4 predicted worse SPPB and TUG outcomes. In the SARC group, F above 4 increases the odds of poorer scores in SPPB OR=1.097; CI 95% 1.053-1.146 and TUG, OR=1.096; CI 95% 1.104-1.266. Conclusion: The study showed that the results obtained in the SARC F questionnaire correlate with the possibilities of physical functioning in patients with hip osteoarthritis SARC F is an inexpensive method that can be used to assess the risk of sarcopenia. Healthcare professionals, especially in primary care, should consider assessing the risk of sarcopenia especially in people with hip osteoarthritis.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

Nitric oxide (NO) is involved in physiological processes, including vasodilatation, wound healing and antibacterial activities. As NO is a free radical, designing drugs to generate therapeutic amounts of NO in controlled spatial and time manners is still a challenge. In this study, the NO donor S-nitrosoglutathione (GSNO) was incorporated into the thermoresponsive Pluronic F-127 (PL) - chitosan (CS) hydrogel, with an easy and economically feasible methodology. CS is a polysaccharide with known antimicrobial properties. Scanning electron microscopy, rheology and differential scanning calorimetry techniques were used for hydrogel characterization. The results demonstrated that the hydrogel has a smooth surface, thermoresponsive behavior and good mechanical stability. The kinetics of NO release and GSNO diffusion from GSNO-containing PL/CS hydrogel demonstrated a sustained NO/GSNO release, in concentrations suitable for biomedical applications. The GSNO-PL/CS hydrogel demonstrated a concentration-dependent toxicity to Vero cells, and antimicrobial activity to Pseudomonas aeruginosa (minimum inhibitory concentration and minimum bactericidal concentration values of 0.5 µg·mL^-1 of hydrogel, which corresponds to 1 mmol·L^-1 of GSNO). Interestingly, the concentration range in which the NO-releasing hydrogel demonstrated an antibacterial effect was not found to be toxic to the Vero mammalian cell. Thus, the GSNO-PL/CS hydrogel is a suitable biomaterial for topical NO delivery applications.

Introduction: The association of gene variants for interleukin 6(IL-6) (rs1800796), interleukin 10 (IL-10) (rs1800896) and tumor necrosis factorα (TNFα (rs1800629) with the occurrence of spontaneous preterm birth (PTB) was investigated to determine whether these genetic variants are a risk factor. Materials and methods: 199 blood samples from pregnant women who had given birth prematurely and 200 control blood samples were analyzed to determine single nucleotide polymor-phisms (SNPs) of genes for IL-6 (rs1800796), IL-10 (rs1800896) and TNFα (rs1800629). The control samples were samples from pregnant women with term delivery. Isolation of DNA was per-formed on mini-spin columns according to the manufacturer's protocol. The quality and purity of the isolated DNA were tested using a Qubit 3 fluorometer. Genotyping was performed with an ABI PRISM 7500 SDS using TaqMan SNP genotyping assays. The genotypes obtained were an-alyzed using the 7500 Software v2.3 package. Results: Carriers of the A/A genotype for the rs1800629 of the TNFα gene have 4.81 times greater chance of late-onset PTB compared to carriers of the G/G and A/G genotypes in the recessive inheritance model. The presence of the G/G genotype in the recessive inheritance model compared with the G/A and A/A genotypes for the rs1800896 of the IL-10 gene represents a potentially protective factor, with mothers in the term-birth group having an almost 2-fold lower odds of PTB in general and an almost 10-fold lower odds of early PTB. On the other hand, carriers of the A/G genotype of rs1800896 have a 1.54-fold higher chance of preterm birth in general and a 1.6-fold higher chance of late preterm birth in the super dominant inheritance model compared to the A/A and G/G genotypes in the group of mothers with PTB. In this study, no association was found between PTB and rs1800796 of the IL-6 gene. Conclusion: rs1800629 in mothers was associated with PTB. rs1800896 shows a potentially protective effect for the occurrence of PTB in this study. No association was found between PTB and rs1800796.

Petrosamine (1) – a colored pyridoacridine alkaloid from the Belizean sponge, Petrosia sp. that is also a potent inhibitor of acetylcholine esterase (AChE) – was investigated by spectroscopic and computational methods. Analysis of the petrosamine free energy landscapes, pKa and tautomerism revealed an accurate electronic depiction of the molecular structure of 1 as the di-keto form, with net charge of q = +1, rather than a dication (q = +2) under ambient conditions of isolation-purification. The pronounced solvatochromism (UV-vis) reported for 1, and related analogs, was investigated in detail and is best explained by charge delocalization and stabilization of the ground state (HOMO) of 1 rather than an equilibrium of competing tautomers. Refinement of the molecular structure of 1 by QM methods complements published computational docking studies to define the contact points in the enzyme active site that may improve design of new AChE inhibitors based on the pyridoacridine alkaloid molecular skeleton.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

First, we examine how spin is treated in special relativity and the necessity of introducing spin supplementary conditions (SSC) and how they are related to the choice of a center-of-mass of a spinning particle. Next, we discuss quantum electrodynamics and the Foldy-Wouthuysen transformation which we note is a position operator identical to the Pryce-Newton-Wigner position operator. The classical version of the operators are shown to be essential for the treatment of classical relativistic particles in general relativity, of special interest being the case of binary systems (black holes/neutron stars) which emit gravitational radiation.

Introduction: Type 2 diabetes (T2D) is a major driver of health care costs, thus treatments enabling T2D reversal may reduce expenditures. We examined the impact of a T2D continuous care intervention (CCI) on health care utilization. Previous research documented that CCI, including individualized nutrition supported by remote care, simultaneously reduced hemoglobin A1c and medication use and improved cardiovascular status after two years; however, the impact on utilization is unknown. Methods: This study used four years of data (two years pre-intervention, two years post-intervention) from the Indiana Network for Patient Care (INPC) health record. Two methods estimated the impact of CCI on utilization. First, an interrupted time series (ITS) including only CCI participants (n=193) compared post-intervention utilization to expected utilization had the pre-intervention trend persisted. Deviation from the trend was estimated non-parametrically for each 6-month interval after the implementation of CCI . Second, a 1:3 matched comparator group (n=579) was constructed and used for a difference-in-differences (DiD) analysis. The primary outcome was annualized outpatient encounters. Secondary outcomes included emergency encounters and hospitalizations. Results: In two years prior to intervention, CCI participants had a mean of 5.77 annualized encounters (5.62 outpatient, 0.04 hospitalizations, 0.11 emergency). The CCI group showed a reduction in outpatient utilization after intervention. In ITS analysis, 1.6 to 1.9 fewer annualized outpatient encounters occurred in each 6-month interval post-intervention relative to expected utilization based on pre-intervention trends (p<0.01 each 6-month period; 28-33% reduction). The DiD analysis suggested a larger reduction; 5 fewer annualized outpatient encounters in the quarter after intervention, diminishing to 2.5 fewer after 2 years (p<0.01 each quarter). The study was underpowered to draw conclusions about hospitalization and emergency encounters due to the limited number of CCI patients and the rarity of encounters. Conclusions: Outpatient encounters were significantly reduced for a T2D patient population up to 2 years after receiving an individualized intervention supporting nutrition and behavior change through remote care.

Tissue resident memory T cells (TRM) were first described in 2009. While initially the major focus was on CD8 TRM, there has been recently an increased interest in defining the phenotype and the role of CD4 TRM in diseases. Circulating CD4 T cells seed tissue CD4 TRM, but there also appears to be an equilibrium between CD4 TRM and blood CD4 T cells. CD4 TRM are more mobile than CD8 TRM, usually localized deeper within the dermis/lamina propria and yet may exhibit synergy with CD8 TRM in disease control. This has been demonstrated in herpes simplex infections in mice. In human recurrent herpes infections, both CD4 and CD8 TRM persisting between lesions may control asymptomatic shedding through interferon gamma secretion, although this has been more clearly shown for CD8 T cells. The exact role of the CD4/CD8 TRM axis in the trigeminal ganglia and/or cornea in controlling recurrent herpetic keratitis is unknown. In HIV, CD4 TRM have now been shown to be a major target for productive and latent infection in cervix. In HSV and HIV co-infections, CD4 TRM persisting in the dermis support HIV replication. Further understanding of the role of CD4 TRM and their induction by vaccines may help control sexual transmission by both viruses.

Solute carrier (SLC) proteins transport a wide range of substrates across biological membranes and more than 400 proteins are considered as SLCs based on its sequence. Despite it has important potential applications in drug development, the SLC superfamily is still understudied. Drosophila blot, an orphan SLC protein, regulates F-actin organization in the syncytial blastoderm and the Malpighian tubules. However, the molecular mechanism was unknown. In this study, we found Blot was localized at the furrow canal, the front of the invaginating membrane during cellularization process. Blot is required for maintaining proper morphology of furrow canal and cellularization process. By affinity purification and mass spectrometry we identified RhoGEF ELMO/DOCK complex was required for Blot-mediated F-actin organization and cellularization. Further analysis revealed that ELMO localization depends on Blot. Taken together, we propose Blot plays a role in F-actin organization as an upstream factor of ELMO by recruiting ELMO to the target membrane compartments.

Lemon oils are amongst the highest volume and most frequently traded of the flavour and fragrance essential oils. Citronellal and citral are considered the key components responsible for the lemon note with citral (neral + geranial) preferred. Of the myriad of sources of citral, the Australian myrtaceous tree, Backhousia citriodora, is considered superior. This review examines the history, natural occurrence, the cultivation, the taxonomy, the chemistry, the biological activity, the toxicology, standardisation and the commercialisation of Backhousia citriodora especially in relation to its essential oil.

Controlling and understanding Cu-catalyzed homocoupling reaction is crucial to prompt the development of efficient Cu-catalyzed cross-coupling reactions. The presence of a coordinating base (hydroxide, methoxide) enables the B-to-Cu(II) transmetalation from aryl boronic acid to CuIICl2 in methanol, through formation of a mixed Cu-(μ-OH)-B intermediates. A second B-to-Cu transmetalation to form bis-aryl Cu(II) complexes is disfavored. Instead, organocopper(II) dimers undergo a coupled transmetalation-electron-transfer (TET) allowing the formation of a bis-organocopper(III) complexes readily promoting reductive elimination. Based on this mechanism some guidelines are suggested to control the undesired formation of homocoupling product in Cu-catalyzed cross-coupling reactions.

Agricultural landscapes are more and more characterized by intensification and habitat losses. Landscape composition and configuration are known to mediate insect abundance and richness. In the context of global insect decline, and despite 75% of crops being under insect’s dependence, there is still a gap of knowledge about the link between pollinators and aromatic crops. Fennel (Foeniculum vulgare) is an aromatic plant cultivated in South of France, for its essential oil which is of great economic interest. Using pan-traps, we investigated the influence of the surrounding habitats at landscape scale (semi-natural habitat proportion and vicinity, landscape configuration) and local scale agricultural practices (insecticides and patch size) on fennel-flower-visitor abundance and richness and their subsequent impact on fennel essential oil yield. We found that fennel may to be a generalist plant species. We did not find any effect of intense local management practices on insect abundance and richness. Landscape configuration and the proximity to semi-natural habitat were the main drivers of flying insect’s family richness. This richness positively influenced fennel essential oil yield. Maintaining a complex configuration of patches at the landscape scale are important to sustain insect diversity and crop yield.

The objective was to compare the failure loads of glass ceramic, and polymer crowns against yttria-partially stabilized zirconia (Y-PSZ) crowns with varying yttria concentrations. Monolithic crowns of zirconia (Cercon XT, Katana UTML, BruxZir Anterior), glass ceramic (Celtra press, IPS e.max press, Lisi press), and polymeric materials (Trilor, Juvora, Pekkton) were fabricated and cemented to epoxy abutments. The total number of specimens was 135 for crowns and 135 for discs (15 specimens per material type and design). A universal testing machine was used to perform compressive loading of all crowns to failure with a steel hemisphere along the longitudinal axis of the abutments. Energy dispersive spectroscopy (EDS) was used to identify the concentration (mol% yttria-partially stabilized zirconia) for each zirconia brand. The data were analyzed using a generalized linear model and regression analysis. The results revealed significant differences (P < .05) in mean failure loads for different crown materials: Trilor (6811 ± 960 N) > Juvora (5215 ± 151 N) > Cercon (4260 ± 520 N) = BruxZir (4186 ± 269 N) = e.max (3981 ± 384 N) > Katana (3195 ± 350 N) = Lisi (3173 ± 234 N) = Pekkton (3105 ± 398 N) > Celtra (2696 ± 393 N). EDS showed that the zirconia materials contained yttria at different concentrations (BruxZir = 5Y-PSZ, Cercon = 4Y-PSZ, Katana = 3Y-PSZ). The yttria concentration had a significant effect on the failure load of the Katana (3Y-PSZ) crowns, which revealed lower failure loads than the Cercon (4Y-PSZ) and BruxZir (5Y-PSZ) crowns. New zirconia materials are provided with different yttria concentrations (3Y-, 4Y-, and 5Y-PSZ). Since a higher yttria concentration increases the translucency, clinicians should be aware that 4-5 wt% yttria-partially stabilized zirconia materials provide comparable or higher mechanical properties than e. max glass ceramic for dental application of crowns.

Biomechanics is a branch of biophysics that deals with mechanics applied to biology. The biomechanics of the cornea plays a significant role in managing patients with glaucoma. While evidence suggests a higher risk of glaucoma in patients with thin and stiffer corneas, it also affects the measurement of intraocular pressure (IOP). We reviewed the pertinent literature to help the understanding of corneal biomechanics and how it can help optimize clinical and surgical treatments and a better approach to diagnosing and managing patients with glaucoma.

Eating competence can play a role in helping adolescents navigate their food choices and attitudes toward eating in a healthy and balanced way. In the present study, we investigated the psychometric properties of the Dutch translation of the Eating Competence Satter Inventory 2.0TM (ecSI 2.0TM), which was developed to assess eating attitudes and behaviors. A sample of 900 Flemish adolescents completed the ecSI 2.0TM DUTCH and two self-report measures on eating disorder symptoms and identity functioning (i.e., confusion and synthesis). Confirmatory factor analysis confirmed the four-factor structure of the ecSI 2.0TM DUTCH, and the resulting four subscales (Eating Attitudes, Food Acceptance, Internal Regulation, and Contextual Skills) showed acceptable to excellent reliability (α ranging from .69 to .91). The ecSI 2.0TM also showed to be scalar invariant across sex and age (&lt;17 years, ≥ 17 years). Boys reported significantly higher ecSI 2.0TM DUTCH scores than girls on the four subscales and the total scale. The two age groups did not differ significantly on the ecSI 2.0TM DUTCH scales. Finally, scores on the ecSI 2.0TM subscales showed no or small negative correlations with adolescents’ BMI, large negative correlations with eating disorder symptoms and identity confusion, and large positive associations with identity synthesis. The Dutch translation of the ecSI 2.0TM is a valid and reliable instrument to assess eating competence skills in male and female adolescents.

Nickelate superconductors, R1-xAxNiO2 (where R is a rare earth metal and A = Sr, Ca), experimentally discovered in 2019 exhibit many unexplained mysteries as the existence of a superconducting state with Tc (up to 18 K) in thin films and its absence in bulk materials. Another unexplained mystery of nickelates is their temperature-dependent upper critical field, Bc2T, which can be nicely fitted to two-dimensional (2D) models; however the deduced film thickness, dsc,GL, exceeds the physical film thickness, dsc, by a manifold. To address the latter, it should be noted that 2D models assume that dsc is less than the in-plane and out-of-plane ground state coherence lengths, dsc&lt;ξab0 and dsc&lt;ξc0, respectively, and, in addition, that the inequality ξc0&lt;ξab0 satisfies. Analysis of the reported experimental Bc2T data showed that at least one of these conditions does not satisfy for R1-xAxNiO2 films. This implies that nickelate films are not 2D superconductors, even despite though that the superconducting state is observed only in thin films. Based on this, here we proposed analytical three dimensional (3D) model for global data fit of in-plane and out-of-plane Bc2T in nickelates. The model is based on a heuristic expression for temperature dependent coherence length anisotropy: γξT=γξ01-1a×TTc, where a&gt;1 is a unitless free-fitting parameter. The proposed expression for γξT, perhaps, has a much broader application because it has been successfully applied to bulk pnictide and chalcogenide superconductors.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.