This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Climate change represents a prevalent challenge confronted by humanity, and with cities being one of the regions most heavily impacted by such change, enhancing their climate resilience is paramount in adapting to and mitigating the associated risks and losses. This article evaluates the climate resilience of 270 major cities in China by creating an urban climate resilience indicator system centered on exposure, vulnerability, and resilience. The article analyses the spatial and temporal evolution trend of climate resilience in Chinese cities, as well as the source of regional differences using Kernel density analysis and the Dagum Gini coefficient decomposition. The article then explores the influence of financial investments on urban climate resilience, considering the moderating effect of urbanization rate.

Emergence of zoonotic-human pathogens is proven to be a lethal threat to public health, and RNA virus including influenza viruses, severe acute respiratory syndrome coronavirus, middle east respiratory syndrome coronavirus, Wuhan coronavirus (COVID-19), plays a pivotal role. As those viruses as airborne microorganisms spread mainly by tiny airborne particles, it is important to de-active those airborne particles before their entry into human bodies. In this study, we investigated the effect of far infrared (FIR) radiation on inhibition of airborne microorganisms. The result confirmed that double stand DNA from airborne microorganisms were stable under mild FIR radiation. However, single strand RNA from them was found to be sensitive to FIR radiation, indicating that RNA virus in airborne particles is instable under FIR radiation. Based on this observation, two models on usage of FIR radiation to prevent RNA virus transmission and cure RNA virus infection were proposed, implying that FIR radiation might be a cheap, convenient, and efficient method in clinic to treat RNA virus.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

Balanced and coordinated economic development across regions is a critical goal of regional economic development and new-type urbanization in China. However, few studies have examined economic growth convergence clubs at the county level. To extend the research on convergence clubs, this research applies a log t convergence test and a dynamic spatial ordered Probit model (DSOP) to endogenously identify economic growth convergence clubs in counties and to examine the influence of initial states and structures on club convergence probability. The study sample covers 2286 counties of China from 1992 to 2010. The results show significant convergence club patterns at the county levels, resulting in the gradual formation of six convergence clubs. The DSOP estimation results show that per capita fixed assets, population density and industrialization have promoted convergence club formation to varying degrees.

Hydrological connectivity plays a major role in solving water resource and eco-environmental problems. However, this phenomenon has not been afforded the attention it deserves. Detailed analysis of connectivity in river systems could provide considerable insight into structural and functional attributes of riverine landscapes. The current study used graph theory approach and associated connectivity indicators to explore the characteristics and evolution of river systems and hydrological connectivity in a large catchment (Poyang Lake, China). The results revealed that the structure of the river system tended to be complex during 1990-2020, characterized by a dynamic evolution of tributaries in certain northern areas. Both river density and complexity exhibited an increasing trend by up to 15%, with the change rate after 2000 approximately twice as high as that of the preceding period. Overall, human activities across the catchment are more likely to play a key role in leading to significant changes in the quantity, morphometric, and structure characteristics of the river system. Additionally, the functional connectivity analysis indicated that the index of connectivity (IC) in the downstream catchment is stronger than that of the upstream vegetation areas, suggesting a strong contribution to the runoff-sediment transport (r=0.6-0.7). This study highlights the spatial and temporal evolution of both the structural and functional connectivity in the large Poyang Lake catchment. The findings of this work will bene-fit future water resource management and applications by providing a strategy for protecting the surface hydrology and mass transport of large river basins under climate and land-use changes.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

In the era of persistent globalization, climate governance has emerged as a prominent concern within both the theoretical community and government departments of diverse nations. Of particular interest in academic research is the adverse effect of climate shocks on the global economy. This paper employs average temperature as a surrogate indicator for climate shocks and examines the influence of temperature fluctuations on inflation levels using a balanced panel dataset from 1995 to 2021. The findings indicate a positive association between temperature change and inflation within the country, which remains consistent even after subjecting the analysis to multiple robustness tests. Furthermore, accounting for heterogeneity reveals variations in the magnitude of response of inflation levels to temperature fluctuations. Regarding the analysis of underlying mechanisms, the study underscores the significance of energy demand as a pivotal pathway influencing inflationary pressures at the national level. Lastly, by incorporating GDP per capita as a threshold, the research reveals a nonlinear relationship between temperature change and inflation levels.

The future power equipment tends to take hydrogen or middle/low heat-value syngas as fuel for low emission. The heat transfer of film cooled turbine blade shall be influenced more by radiation. Its characteristic of conjugate heat transfer is studied experimentally and numerically in the paper by considering radiation heat transfer, multi-composition gas and TBC. The Weighted Sum of Gray Gases spectral model and Discrete Transfer Model are utilized to solve the radiative heat transfer in the multi-composition field, while validated against the experimental data for the studied cases. It is shown that the plate temperature increases significantly when considering the radiation and the temperature gradient of the film cooled plate becomes larger. It is also shown that increasing percentage of steam in gas composition results in increased temperature on the film-cooled plate. The normalized temperature of the film-cooled plate decreases about 0.02, as the total percentage of steam in hot gas increases per 7%. As for the TBC effect, it can smooth out the the temperature distribution and insulate the heat to a greater extent when the radiative heat transfer becomes significant.

An increasing number of studies have proposed that corporate social responsibility (CSR) performance depends on how companies apply their resources and capabilities to implement CSR. A firm’s ability to integrate, build, and reconfigure internal and external competencies to respond to environmental changes is its dynamic capability. Implementation of CSR at the strategic level will contribute to a firm’s sustainability. However, the research on strategic CSR is incipient. This study explores possible mechanisms to investigate how dynamic capability influences the performance of strategic CSR in China. By analyzing 134 Chinese listed companies in the period 2017–2019, in this study, we found that firms with a high level of dynamic capability were less likely to adopt strategic CSR practices, and had a low strategic CSR adoption performance. The results confirmed the loss aversion channel, indicating that firms with a high dynamic capability level were loss averse and that managers had a decreasing sensibility in decision-making and allocated fewer company resources in CSR projects. These results can help companies to better understand the dynamic capability and how dynamic capability contributes to the adoption of strategic CSR and performance over time. The policy implications of the study are also discussed.

Artificial groundwater recharge is commonly used for drinking water supply. The resulting water quality is highly dependent on the raw water quality. In many cases, pre-treatment is required. Pre-treatment improves the drinking water quality, although how and to what extent it affects the subsequent pond water quality and infiltration process, is still unknown. We evaluated two treatment systems by applying different pre-treatment methods for raw water from a eutrophic and temperate lake. An artificial recharge pond was divided into two parts, where one received raw water, only filtered through a micro-screen with 500 µm pores (control treatment), while the other part received pre-treated lake water using chemical flocculation with polyaluminium chloride (PACl) combined with sand filtration, i.e. continuous contact filtration (contact filter treatment). Water quality such as cyanobacterial biomass, microcystin-LR as well as organic matter and nutrients were measured in both treatment processes. We found cyanobacterial biomass and microcystin-LR level after the contact filter treatment was significantly different from the control treatment and also significantly different in the pond water. In addition, with contact filter treatment, total phosphorus (TP) and organic matter removal were significantly improved in the end water, TP was reduced by 96 % (< 20 µg/L) and the total organic carbon (TOC) was reduced by 66 % instead of 55 % (TOC content around 2.1 mg/L instead of 3.0 mg/L). This full-scale onsite experiment demonstrated effective pre-treatment would benefit a more stable water quality system, with less variance and lower cyanotoxin risk. In a broader drinking water management perspective, the presented method is promising to reduce cyanotoxin risk, as well as TP and TOC, which are all predicted to increase with global warming and extreme weather.

The phonon modes in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems have been systematically studied by Raman spectroscopy. The new phonon modes of 104 cm^-1, 94 cm^-1, and 89 cm^-1 were found in all these samples. A crude estimate about the wavenumber of the collective vibration of the stable CuO2 plane was given in this paper. The standard deviations of the new phonons in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems were discussed. The results of the calculation indicated that the 104 cm^-1 mode probably stands the c-direction collective vibration of the stable CuO2 plane, the 94 cm^-1 mode stands the a-direction vibration, and the 89 cm^-1 mode stands b-direction vibration. The relevance between these phonons and the superconductivity was discussed. It is found that, as the T_c decreased, the 104 cm^-1 mode and the 94 cm^-1 mode softened, and the 89 cm^-1 mode hardened slightly.

'Huangguan' pear has significant social and economic value, and phosphorus, as one of the three main mineral elements of plants, has an irreplaceable effect on the normal growth of 'Huangguan' pear trees. The objective of this study was to predict the content of phosphorus in the pulp and peel of ‘Huangguan’ pears nondestructively and conveniently by using near-infrared spectroscopy (900–1700 nm) technology. First, twelve algorithms are used to preprocess the original spectral data, and the partial least squares regression algorithm and the gradient boosting regression tree algorithm are used to build a full-band prediction model based on the original spectral data and the processed spectral data. The characteristic wavelengths were extracted using genetic algorithms, followed by establishing a characteristic wavelength prediction model. The prediction accuracy of the models was evaluated according to the coefficient of determination R² and the relative analysis error RPD. The study found that the best prediction model for predicting phosphorus content in the pulp of 'Huangguan' pear was MSC-GA-PLSR, which had R²=0.843 and RPD=1.857 in the modelling set and R²=0.989 and RPD=7.041 in the prediction set. The best prediction model for predicting phosphorus content in the peel of ‘Huangguan’ pear was SG+SNV+FD-GA-PLSR, which had R²=0.991 and RPD=7.470 in the modelling set and R²=0.974 and RPD=4.414 in the prediction set, and the effect was good and met expectations. The results demonstrated that near-infrared spectroscopy could successfully achieve nondestructive detection of phosphorus content in the pulp and peel of 'Huangguan' pears.

Ethnopharmacological relevance: Novel coronavirus disease (COVID-19) outbroke in Wuhan has imposed a huge influence onto the society in term of the public heath and economy. However, so far, no effective drugs or vaccines have been developed. Whereas, the Traditional Chinese Medicine (TCM) has been considered as a promising supplementary treatment for the disease owing to its clinically proven performance on many diseases even like severe acute respiratory syndrome (SARS). Meanwhile, many side-effect (SE) reports suggest the SE of the TCM prescriptions cannot be ignored in curing the COVID-19, especially because COVID-19 always simultaneously leads to dramatic degradation of the patients’ physical condition. How to evaluate the TCM regarding to their latent SE is a urgent challenge. Aim of the study: In this study, we use an ontology-based side-effect prediction framework (OSPF) developed in our previous work and Artificial Neural Network (ANN)-based deep learning to evaluate the TCM prescriptions that are officially recommended in China for novel coronavirus (COVID-19). Materials and methods: Firstly, we adopted the OSPF developed in our previous work, where an ontology-based model separate all the ingredients in a TCM prescription into two categories: hot and cold. Then, we established a database by converting each TCM prescription into a vector containing the ingredient dosage and the according hot/cold attribution as well as the safe/unsafe label. And, we trained the ANN model using this database, after which a safety indicator (SI), as the complementary percentage of side-effect (SE) possibility, is then given for each TCM prescription. According to the proposed SI from high to low, we re-organize the recommended prescription list. Secondly, by using this method, we also evaluate the safety indicators of some other famous TCM prescriptions that are not in the recommended list but are used traditionally to cure flu-like diseases for extending the potential treatments. Results: Based on the SI generated in the ANN model, FTS, PMSP, and SF are the safest ones in recommended list, which all own a more-than-0.8 SI. Whereas, JHQG, LHQW, SFJD, XBJ, and SHL are the prescriptions that are most likely unsafe, where the indicators are all below 0.2. In the extra list, the indicators of XC, XQRS, CC, and CHBX are all above 0.8, and at the meantime, XZXS, SJ, QW, and KBD’s indicators are all below 0.2. Conclusions: In total, there are seven TCM prescriptions which own the indicators more than 0.8, suggesting these prescriptions should be considered firstly in curing COVID-19, if suitable. We believe this work will provide a reasonable suggestion for the society to choose proper TCM as the supplementary treatment for COVID-19. Besides, this work also introduces a pilot and enlightening method for creating a more reasonable recommendation list of TCM to other diseases.

Growth-regulating factor (GRF) is a plant-specific transcription factor family, which is involved in nearly all of the central developmental processes in plants. However, little is known about GRF family genes in cultivated sunflower. In this study, 17 GRF genes were identified and characterized from sunflower genome. Their gene structures, conserved motifs, chromosomal distributions and phylogenetic relationships were analyzed. The expression patterns of these genes were detected in various tissues of sunflower inbred line SK02R, which revealed that the 10 seed-specific GRF genes may play important roles during seed development in sunflower. Additionally, transcripts changes of the GRFs under two major abiotic stresses and phytohormones showed that most of the detected GRFs were reduced significantly by GA3 treatment, and other treatments(ABA, NaCl and PEG6000) differently regulated various sunflower growth-regulating factors at different time points. MiR396 target analysis indicated that there may exist a complicated homeostasis between miR396 and its targets GRF and WRKY transcription factor genes in cultivated sunflower. The phylogenetic and expression analyses of the GRF gene family in sunflower would be useful for further cloning and function exploration of the HaGRF genes.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

The study examines the relationship between corporate social responsibility (CSR) and the corporate life cycle (CLC) of the Chinese pharmaceutical listed companies for the duration of 2010 to 2018. The firm cash flow pattern is used as a proxy for the CLC. The study results indicate that the relationship between CSR and CLC is positive and linear in all the phases of the CLC including, the introduction, growth and maturity stage. Although the relationship is smaller and more significant at the maturity phase. The research further shows that investors incorporating social responsibilities values play a key role in the firm cash flow performance (CFP) across all the firm stages. Whilst, employees espousing social responsibility tenets can only improve CFP in the decline or shakeout stages. Likewise, embedding CSR into the customers group only improves CFP at the maturity stage. Applying the lag effects lead to the same study results. The finding for the bi-directional causality indicates that although CSR can positively influence CFP, CFP is ultimately more associated with the firm unobservable characteristics rather than performance attributed to CSR. On the whole, our study results point to positive causality between CSR and CFP across all the firm life stages and the CSR has a mediating effect on each life cycle.

Existing research concerning the effects of the sitting birth position during the second stage of labour on maternal and neonatal outcomes remains controversial, and there is a lack of studies to explore its effect on the childbirth experience. The objective of this study is to explore whether the sitting birth position would influence maternal and neonatal outcomes, as well as the childbirth experience reported by Chinese women using the Childbirth Experience Questionnaire (CEQ). A total of 296 women (including primiparous women and multiparous women) were enrolled in our study, and they were divided into the sitting position cohort (n=106) or the lithotomy position cohort(n=116). The study found that primiparous women in the sitting position cohort had a shorter duration of the second stage of labour, higher spontaneous vaginal birth rates, lower episiotomy rates and better childbirth experience (p<0.01). There was no significant difference for perineal lacerations, 2h-postpartum haemorrhage (P>0.05) between the two cohorts of primiparous women. After adjusting for confounding factors through multiple linear and logistic regression analyses, the results remained consistent with those reported above. No neonate in each cohort had Apgar scores at 1min and 5 min postpartum less than 7 or the Cord artery pH less than 7.00, regardless of parity. In addition, among multiparous women, there was no significant difference in any maternal and neonatal outcomes and women’s CEQ scores (p>0.05) between two cohorts. Based on the findings, we recommend that women could take the sitting birth position into account when giving birth for a positive childbirth experience, especially for primiparous women. The study could also serve as a reference for healthcare providers in the management of childbirth positions and the development of high-quality maternal care.

Control of nutrients, mainly nitrogen (N) and phosphorus (P), plays a significant role in preventing cyanobacterial blooms (harmful algal blooms (HABs)). This study aimed at evaluating changes in the risk of the occurrence of cyanobacterial blooms and advancing the understanding of how N and P affect the growth of cyanobacteria in a eutrophic lake, Lake Vombsjön, in southern Sweden. Statistical analysis was used to demonstrate the pattern of cyanobacterial blooms, that the highest content present in September and the later that algal blooms occur, the more likely it is a cyanobacterial bloom as cyanobacteria became dominating in October and November (90%). Two hypothesises tested in Lake Vombsjön confirmed namely that a high total phosphorus (TP) level correlates with an abundance of cyanobacteria and that low N:P ratio (total nitrogen/total phosphorus < 20) favours the growth of cyanobacteria. To control the growth of cyanobacteria in Lake Vombsjön, the TP level should be kept below 20 µg/L and the N:P ratio be maintained at a level of over 20. The two species Planktothrix agardhii, and Pseudanabaena spp. should be carefully monitored especially in late autumn. Future work should consider any high degree of leakage from the sediment of the dissolved phosphorus available there.

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photons flux of 106 photons/s of commercial VUV lamp limits its range of ionizable analytes as well as sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp through the photoelectric effect ionized the oxygen in the air to obtain the reagent ions O2+, and segmented quadrupole constituted the ion-molecule-reaction region (IMR) and radially focused the ions using a radio-frequency electric field, which improved the yield and transport efficiency of the sample ions and the sensitivity of mass spectrometry, resulting in 44-fold and 1154-fold increase in signal response to benzene and pentanal, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the concentration range of 5-50 ppbv, and daytime RSD reached 3.91% and 6.26%, respectively. Finally, the CIFI ionization source TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs can reach the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

Soybean (Glycine max L.) is an important crop that serves as a source of edible oil and protein. However, little is known about its molecular mechanism of adaptation to extreme environmental conditions. Based on the Arabidopsis thaliana sequence database and Phytozome, a soybean gene that was highly homogenous with the reduced induction of the non-photochemical quenching2 (AtRIQ2) gene, GmRIQ2-like (accession NO.: Glyma.04G174400), was identified in this study. The gene structure analysis revealed that GmRIQ2-like encoded a transmembrane protein. Elements of the promoter analysis indicated that GmRIQ2-like participated in the photosynthesis and abiotic stress pathways. The subcellular localization results revealed that the protein encoded by GmRIQ2-like was located in chloroplasts. The quantitative real-time (qRT)-PCR results revealed that GmRIQ2-like-overexpression (OE) and -knock-out (KO) transgenic soybean seedlings were cultivated successfully. The relative chlorophyll (Chl) and zeaxanthin contents and Chl fluorescence kinetic parameters demonstrated that GmRIQ2-like dissipated excess light energy by enhancing the non-photochemical quenching (NPQ) and reduced plant photoinhibition. These results suggested that GmRIQ2-like was induced in response to strong light and depressed Chl production involved in soybean stress tolerance. These findings indicate that the transgenic seedlings of GmRIQ2-like could be used to enhance strong light stress tolerance and protect soybean plants from photoinhibition damage. This study will serve as a reference for studying crop photoprotection regulation mechanisms and benefits the research and development of new cultivars.

In March 2013, a novel avian influenza A H7N9 virus was emerged in China, which cause rapidly progressive pneumonia and with a high fatality rate. Serologic studies to evaluate neutralizing antibodies of infected patients and birds are invaluable tools for immunogenicity research of H7N9 and epidemiological investigation. Conventional neutralization assays are laborious and time-consuming which also hampered by biosafety requirement. In this study, We construct and produce pseudovirus bearing the full-length hemagglutinin (HA) of H7N9 virus in the Env-defective, luciferase-expressing HIV-1 backbone. The production of lentiviral pseudovirus was analysed by HA gene specific real-time reverse-transcription PCR, transmission electron microscopy (TEM), and Western Blot assay to prove the nucleic acid replication, the morphology of virus, and the expression of HA protein in pseudovirus. After that pseudovirus based inhibition assay was established to detect neutralizing antibodies of a panel of serum samples. Our results demonstrated that H7N9 pseudovirus which had single-cycle infection was generated. By comparing the neutralization antibody titers, pseudovirus based neutralization test could be recognized as an alternative of conventional microneutralization (MN). Hence, we conclude that it is possible to use pseudovirus inhibition assay to screen sera samples, as well as evaluate vaccine-induced neutralizing antibodies against H7N9 virus.

Psycho-social factors are key factors to the powerlessness of infant mothers who breastfeed. As the theory of planned behavior (TPB) is widely used to investigate the correlation between psycho-social factors and breastfeeding behavior, this study aims to examine the utility of TPB constructs to predict breastfeeding behavior and understand TPB-based psycho-social factors’ effectiveness on breastfeeding behavior. A narrative review consulting Web of Science, Scopus, Ebsco, PubMed, and PsycInfo in English and Chinese has been conducted, with the inclusion of twenty studies published between January 2000 and May 2022. It is reported that psycho-social factors based on TPB for breastfeeding such as affective attitude, instrumental attitude, subjective norm, perceived behavioral control (including self-efficacy), moral norm, breastfeeding knowledge, and self-identity can effectively explain the breastfeeding behavior. Future research should improve the theoretical model of TPB-based breastfeeding and implement more localized prediction and intervention studies on breastfeeding.

In bioinformatics research, traditional machine learning methods have demonstrated efficacy in addressing Euclidean data. However, real-world data often encompasses non-Euclidean forms, such as graph data, which contain intricate structural patterns or high-order relationships that elude conventional machine-learning approaches. Representation learning seeks to derive valuable data representations from enhancing predictive or analytic tasks, capturing vital patterns and structures. This method has proven particularly beneficial in bioinformatics and biomedicine, as it effectively handles high-dimensional, sparse data, detects complex biological patterns, and optimizes predictive performance. In recent years, graph representation learning has become a popular research direction. It embeds graphs into a low-dimensional space while preserving the structural and attribute information of the graph, enabling better feature extraction for downstream tasks. This study extensively reviews representation learning advancements, particularly in the research of representation methods since the emergence of COVID-19. We begin with an analysis and classification of neural network-based language model representation learning techniques as well as graph representation learning methods. Subsequently, we explore their methodological innovations in the context of COVID-19, with a focus on the domains of drugs, public health, and healthcare. Furthermore, we discuss the challenges and opportunities associated with graph representation learning. This comprehensive review presents invaluable insights for researchers as it documents the development of COVID-19 and offers experiential lessons to preempt future infectious diseases. Moreover, this study guides future bioinformatics and biomedicine research methodologies.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

The purpose of our study was to discuss Rab 7 effects in chronic kidney disease (CKD). Methods: Using WT and Rab 7-/- mice as target animal, and HK-2 and HMEC-1 cell co-cultured to make cell model. Measuring kidney tissues were evaluated by Sirius red staining, immunohistochemistry staining to CD 34 protein, Transmission electron microscope (TEM) and gelatin zymography to MMP-2 activities. The cell proliferation were measured by CCK-8 and Ki67 protein expression. Measuring cell invasion and total length were evaluated by transwell and in vitro angiogenesis assay. MMP-2 activities were evaluated by gelatin zymography in cell groups. The relative proteins expression were evaluated by Western blot in kidney tissues and cell groups. Results: Hypoxia promoted the expression of Rab7 in HMEC-1, and the activity of MMP-2 related with regulatory molecules such as reversion-inducing-cysteine-rich protein with kazal motifs (RECK), negative correlation with membrane-type 1 MMP (MT1-MMP or MMP-14) on the membrane of TECs. In addition, the up-regulation of the expression of Rab7 inhibited the activity of MMP-2 and proliferation and cyclization of endothelial cells, and the inhibitor of MMP-2 partially blocked the effects of Rab7 on angiogenesis. Furthermore, the similar data were also obtained in the fibrosis kidney tissues of mice. Conclusion: Rab 7 might be an important role in hypoxic TECs regulated angiogenesis, Rab 7 knockdown could improve hypoxic TECs regulated angiogenesis, the relative mechanisms might be correlation with RECK pathway and MMP-2 activities in vivo and vitro study.

Currently, foam mixers are predominantly categorized into two types: low-pressure and high-pressure. Low-pressure mixers primarily use agitator rotation to mix materials. However, they face challenges such as difficulty in cleaning and complex structures. High-pressure mixers, widely adopted for their structural simplicity and lack of need for cleaning devices, effectively mitigate issues associated with low-pressure mixers. Nonetheless, they encounter problems with uneven mixing when processing high-viscosity materials. Historically, the primary solution to this issue was increasing the working pressure. However, the capacity to increase pressure is finite, and higher pressure demands higher quality materials for the mixers. To address the issues high-pressure mixers face when dealing with high-viscosity materials, this study focuses on the polyimide high-pressure mixer. After reviewing previous studies, four design variables were selected: the mixer's impingement angle, inlet diameter, outlet diameter, and impingement pressure. Using a Full Factorial Design of Experiments (DOE), the significance of the impact exerted by these four variables on Mixing Unevenness was analyzed, determining the extent of their influence. Optimal Latin Hypercube Sampling generated several random sample points, followed by the establishment of both a Back Propagation (BP) Neural Network approximation model and a Kriging approximation model. A Genetic Algorithm was then applied to optimize these two approximation models, resulting in the optimal combination of design variables. The research findings indicate that the BP Neural Network exhibits higher predictive accuracy compared to the Kriging prediction model. The optimal combination of parameters, optimized through the Genetic Algorithm (GA), reduced the Mixing Unevenness by 69.1%, effectively decreasing the Mixing Unevenness of the mixer head.

As metabolomics is widely used in the study of disease mechanisms, more and more studies have found that metabolites play an important role in the occurrence of diseases. The aim of this study is to investigate the effects and mechanisms of quercetin in high-fat-sucrose diet (HFD)-induced nonalcoholic fatty liver disease (NAFLD) development using nontargeted metabolomics. A rat model of NAFLD was established by feeding with a HFD for 30 and 50 days. Results indicated quercetin exhibited hepatoprotective activity in HFD-induced NAFLD rats in 30 days by regulating fatty acids related metabolites (adrenic acid, etc.), inflammation related metabolites (arachidonic acid, etc.), oxidative stress related metabolites (2-hydroxybutyric acid) and other differential metabolites (citric acid, etc.). However, quercetin couldn’t improve NAFLD in 50 days maybe it couldn’t reverse the inflammation condition induced by long-term high-fat diet. These data indicate that dietary quercetin may be beneficial to NAFLD at early stages. Furthermore, combining metabolomics and experimental approaches opens up avenues of effects and mechanisms of drugs for complex diseases.

Fructus Amomi (FA) is usually regarded as the dried ripe fruits of Amomum villosum Lour. (FAL) or Amomum villosum Lour. var. xanthioides T. L.Wu et Senjenis (FALX) However, FAL, which always has a much higher price because of its better quality, is confused with FALX in the market. As volatile oil is the main constituent of FA, a strategy of chromatography-mass spectrometry (GC-MS) and chemometric approches was applied to compare the chemical composition of FAL and FALX. The results showed that the oil yield of FAL was significantly higher than that of FALX. Total ion chromatograph (TIC) showed that cis-nerolidol existed only in FALX. Bornyl acetate and camphor, could be considered as the most important ones in FAL and FALX respectively. Moreover, hierarchical cluster analysis (HCA) and principal component analysis (PCA) successfully distinguished the chemical constitutes of the volatile oils in FAL and FALX. Additionally, bornyl acetate, α-cadinol, linalool, β-myrcene, camphor, d-limonene, terpinolene and endo-borneol were selected as the potential markers for discriminating FAL and FALX by partial least squares discrimination analysis (PLS-DA). In conclusion, this present study first developed a scientific approach to separate FAL and FALX based on volatile oils by GC-MS combined with chemometric techniques.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

Background: Inhalation exposure to carcinogenic metals like cadmium (Cd) is a significant global health concern linked to various cancers. However, understanding their precise carcinogenic mechanism remains elusive. Methods: Using the colon cancer (CC) rat model and implanted intestinal stent, exposed them to atomized oxygen and nitrogen (O2/N2) gas containing Cd. Results: Atmospheric Cd intensified inflammation in CC cells, heightening nicotinamide adenine dinucleotide phosphate 1 (NOX1) activity, generating increased reactive oxygen species (ROS). This escalated ROS production triggered abnormal Wnt protein secretion, activating the Wnt/β-catenin pathway, stimulating CC cell proliferation. No discernible body weight effect was seen in CC mice, possibly due to later-stage tumor weight gain, masking rat changes. Cd facilitated colon tumor restructuring and cell migration later. Intestinal stents inhibited superoxide dismutase 1 (SOD1) in CC mice's tumors, with no clear effects on NOX1, SOD2, and catalase (CAT) enzymes. Elevated ROS levels didn't substantially impact Wnt/β-catenin and might slow its imbalance. Stent implantation eased inflammation, reducing CC cell proliferation but induced discomfort in rats, reducing food intake and weight. Conclusion: Cd might partially foster CC tumorigenesis via the ROS-mediated Wnt/β-catenin pathway. The effect of Cd on the invasive effect of intestinal stents in cancerous colon was not significant.

Fake news detection has become a significant topic based on the fast-spreading and detrimental effects of such news. Many methods based on deep neural networks learn clues from claim content and message propagation structure or temporal information, which have been widely recognized. However, such models (i) ignore the fact that information quality is uneven in propagation, which makes semantic representations unreliable. (ii) Most models do not fully leverage spatial and temporal structure in combination. (iii) Finally, internal decision-making processes and results are non-transparent and unexplained. In this study, we develop a trust-aware evidence reasoning and spatiotemporal feature aggregation model for more interpretable and accurate fake news detection. Specifically, we first design a trust-aware evidence reasoning module to calculate the credibility of posts based on a random walk model to discover high-quality evidence. Next, from the perspective of spatiotemporal structure, we design an evidence-representation module to capture the semantic interactions granularly and enhance the reliable representation of evidence. Finally, a two-layer capsule network is designed to aggregate the implicit bias in evidence while capturing the false portions of source information in a transparent and interpretable manner. Extensive experiments on two benchmark datasets indicate that the proposed model can provide explanations for fake news detection results, as well as can achieve better performance, boosting 3.5% in F1-score on average.

Background: LncRNA and pyroptosis play important roles in cancer development and tumor immune microenviroment. However, pyroptosis-related lncRNAs (PRLs) in ovarian cancer have not been identified and its impact on prognosis and immune response are not fully understood. Methods: Using pearson correlation analysis, PRLs were screened. Subsequently, we constructed a prognosis signature by using LASSO cox regression. In addition, the association between risk score and cancer immune environment was analyzed. Results: In TCGA-RNA-seq cohort (n=377), 32 prognostic PRLs were selected and a 7-gene signature were developed and had high accuracy in predicting the OS of ovarian cancer patients. Stratification analysis suggested that it might serve as an independent prognostic indicator. Except to clinical outcome, the signature was significantly associated with tumor immune microenvironment. Patients with high risk score exhibited lower infiltration abundance of MHC class Ⅰ cells, Type Ⅰ IFN response and immunotherapy response. In ovarian cancer, TYMSOS was highly expressed and its high expression was associated with worse OS. TYMSOS deletion in ovarian cancer cell lines inhibited the cell proliferation, invasion and migration, indicating that it might serve as a novel biomarker in ovarian cancer. Conclusions: The prognostic PRLs signature constructed in this work is available for prognostic prediction and immune microenvironment infiltration in ovarian cancer.

The efficiencies of conventional triple organic Rankine cycle (TORC) configurations are restricted by the low critical temperatures of common working fluids (＜320 °C). This paper proposes a high-temperature TORC system. A near-azeotropic mixture biphenyl/diphenyl oxide (BDO), which has stellar track record in the high-temperature ORC applications, is innovatively adopted as the top and middle ORC fluid simultaneously. The top cycle evaporation temperature is up to 400 °C in view of BDO’s high stability. Five conventional organic fluids are chosen for the bottom ORC. Fundamentals of the TORC system are illustrated, and mathematical models are built. Thermo-economic performance is investigated. The results hint that the optimal thermodynamic property is achieved on the use of benzene as the bottom fluid. The maximum thermal and exergy efficiencies are respectively 40.86% and 74.14%. The largest irreversible loss occurs inside the heat exchanger coupling the middle and bottom ORCs, accounting for above 30% of the total entropy generation. The levelized energy cost (LEC) is 0.0284 $/kWh. Given the same heat source condition, the TORC system can boost efficiency by 1.02% and drive down LEC by 0.0024 $/kWh compared with a BDO mixture-based cascade ORC.

To improve the understanding of soil–pile interaction of laterally loaded piles, the quasi-static test of pile group foundation in silty clay with 5 foundation piles arranged in cross shape is carried out. The direct measurement-based p–y curves at different depths showed nonlinear behavior, in which the initial stiffness and ultimate soil reaction increased as the depth increased. The loading displacement amplitude corresponding to the failure of each foundation pile in the high axial compression reinforced concrete pile group foundation is given as follows: the front-end nappe foundation pile (#3 pile) is 6mm, the middle pile is 16mm, the front-end nappe foundation pile is 20mm, and the loading displacement amplitude of side pile is 24mm. In silty clay, due to the existence of pile group effect, the edge effect has little effect on the horizontal foundation bed coefficient of foundation pile in pile group, while the influence of masking effect on the horizontal foundation bed coefficient of each foundation pile in pile group is not related to the position of pile, but only to the existence of masking effect, and the influence of different columns of masking effect on the horizontal foundation bed coefficient is the same.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

Peach (L.) is a kind of fruit tree with considerable economic and nutritional significance. However, it shows a high sensitivity to drought stress, which has a profound impact on its growth. L-methionine (MET) and L-proline (PRO) are two amino acids synthesized by plants, which play an important role in abiotic stress response. However, their exact mechanism of action remains elusive. Through physiological analysis, MET (500ppm) and PRO (500ppm) treatments can effectively reduce the adverse effects of drought stress on the growth of peach seedlings. The results show that MET and PRO can effectively inhibit the stomatal opening of plant leaves under drought conditions and reduce the water evaporation of leaves under drought conditions. In addition, the application of MET or PRO promoted the accumulation of carbohydrates in the leaf tissues of peach seedlings under drought conditions, increased the intracellular relative water content (24%, 24%), decreased the leaf electrical conductivity (21%, 24%), and alleviated the membrane damage caused by drought. Experimental studies have confirmed that the alleviation of drought stress is due to the removal of reactive oxygen species (ROS) in vivo, that is, the downregulation of malondialdehyde (18%, 19%)，peroxidase (50%, 5%) and superoxide dismutase (12%, 14%) activities. In addition, the application of exogenous amino acids also improved the root morphological structure and root vitality of peach seedlings，which was conducive to absorbing external buffer substances and alleviating drought stress. In summary, the application of exogenous amino acids can effectively alleviate the effects of drought stress on plants and reduce the harm.

Aiming to improve the flame retardancy performance of natural rubber (NR), we developed a novel flame retardant synergistic agent through grafting of MCM-41 to graphene oxide (GO)，named as GO-NH-MCM-41，as an assistant of intumescent flame retardants (IFR). The structure of GO-NH-MCM-41 was characterized by FTIR, TEM and SEM tests, which confirmed that a fine grafting had been applied between GO and MCM-41. The flame retardancy of NR/IFR/GO-NH-MCM-41 composites was evaluated by limited oxygen index (LOI), UL-94 and cone calorimeter test. The LOI value of NR/IFR/GO-NH-MCM-41 reached to 26.3%; the UL-94 ratings improved to V-0 rating. Moreover, the addition of GO-NH-MCM-41 obviously decreased the peak heat release rate (PHRR) and the total heat release (THR) of the natural rubber composites. And the addition of GO-NH-MCM-41 increased the thickness of char residue. The images of SEM indicated the char residue were more compact and continuous. The degradation of GO-NH-MCM-41 based NR composites completed with a mass loss of 35.57% at 600 ℃. The tensile strength and the elongation at break of NR/IFR/GO-NH-MCM-41 composites were 13.9 MPa and 496.7%, respectively. The results of rubber process analyzer (RPA) reached the maximum value, probably due to a better network of the fillers in the matrix.

Under the increasingly severe global heat threat, continuous high temperature has far-reaching effects on plant growth and development and become a major constraint to crop production. The development of heat-resistant varieties has become research hotspot in many fields, and it is also necessary to establish effective identification methods. In this study, twenty Brassica rapa varieties were selected to to investigate the physiological and biochemical characteristics under heat stress, explore the relationship between physiological response and the heat resistance mechanism, select some typical heat-resistant and heat-sensitive varieties. The effects of photosynthetic electron transfer and antioxidant pathway on heat resistance of Brassica rapa were identified. These findings will providing an important reference for the physiological regulation and identification method of high-temperature stress in plants.

The Arbas cashmere goat is a unique biological resource that plays a vital role in livestock husbandry in China. LCDM is a medium with special small molecules (consisting of human LIF, CHIR99021, (S)-(+)-dimethindene maleate, and minocycline hydrochloride) for generation pluripotent stem cells (PSCs) with bidirectional developmental potential in mice, humans, pigs, and bovines. However, there is no report on whether LCDM can support for generation of PSCs with the same ability in Arbas cashmere goats. In this study, we applied LCDM to generation goat induced PSCs (giPSCs) from goat fetal fibroblasts (GFFs) by reprogramming. The derived giPSCs exhibited stem cell morphology, expressing pluripotent markers, and could differentiate into three germ layers. Moreover, the giPSCs differentiated into the trophectoderm lineage by spontaneous and directed differentiation in vitro. The giPSCs contributed to embryonic and extraembryonic tissue in preimplantation blastocysts and postimplantation chimeric embryos. RNA-sequencing analysis showed that the giPSCs were very close to goat embryos at the blastocyst stage and giPSCs have similar properties to typical extended PSCs (EPSCs). The establishment of giPSCs with LCDM provides a new way to generate high quality of PSCs from domestic animals and lays the foundation for basic and applied research in biology and agriculture.

Uganda is one of the poorest nations in the world. To address the developmental challenges and understand social and economic status, it is important to obtain accurate data in a timely manner. Many studies have demonstrated that nighttime lights (NTL) can be used to measure human activities. Nevertheless, methods developed from these studies (1) suffer from coarse resolutions, (2) fail to capture the nonlinearity and multi-scale variability of geospatial data, and (3) perform poorly for agriculture-dependent regions. This study proposes a new enhanced light intensity model (ELIM) to estimate the Gross Domestic Product (GDP) at sub-national scales for Uganda. This model is developed by combining the NTL data from the Suomi National Polar-orbiting Partnership Visible Infrared Imaging Radiometer Suite (NPP-VIIRS), the population data from the Global Human Settlement Layer (GHSL), and information on agricultural production and market prices across several commodity types. This resulted in a gridded dataset for GDP and GDP per capita for Uganda at 1 km spatial resolution and district level to capture the spatial heterogeneity in economic activity.

Mucin glycans are important component of the mucus barrier and vital defence against physical and chemical damage as well as pathogens. Abnormal expression of mucin glycans can lead to disease, especially cancer. Here, we first summarize the main types of glycosylation on mucins and the mechanisms by which abnormal mucin glycans occur. We next describe the role of ab-normal mucin glycans in cancer. Finally, we describe MUC1-based antibodies, vaccines, radio-pharmaceuticals, and CAR-T therapies using the best characterized MUC1 as an example.

Epigenetic modifications are closely related to diseases and physiological health, mainly including DNA methylation, RNA methylation, histone acetylation, and non-coding RNA. Recently, a large amount of research has been conducted on the detection of epigenetic modifications. Electrochemical biosensors, with their low cost, high sensitivity, high compatibility, and simple operation, have been widely used in the detection of epigenetic biomarkers. This review discusses the detection of epigenetic biomarkers using different electrochemical sensing methods. Here we discuss various aspects, including free labels, signal labeling, signal amplification, nano-based electrodes, and the combined use of other methods. By summarizing the existing electrochemical detection methods for epigenetic modifications, this review also proposes the future development trends and challenges for electrochemical biosensors in this field.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

Noctuidae is known to have high species diversity, although the genomic diversity of Noctuidae species have not been studied extensively. Investigation of transposable elements (TEs) in this family can improve our understanding on the genomic diversity of Noctuidae. In this study, we annotated and characterized genome-wide TEs in ten noctuid species belonging to seven genera. With multiple annotation pipelines, we constructed a consensus sequence library containing 1,038 –2,826 TE consensus. The genome content of TEs showed high variation in the ten Noctuidae genomes, ranging from 11.3% to 45.0%. The relatedness analysis indicated that the TE content, especially the content of LINEs and DNA transposons, are positively correlated with the genome size (r=0.86, p-value=0.001). We identified SINE/B2 as a lineage-specific subfamily in Trichoplusia ni, a species-specific expansion of LTR/Gypsy subfamily in Spodoptera exigua, and a recent expansion of SINE/5S subfamily in Busseola fusca. We further revealed that of the four TE classes, only LINEs showed phylogenetic signal with high confidence. We also examined how the expansion of TEs contributed to the evolution of noctuid genomes. Moreover, we identified a total of 56 horizontal transfer TE (HTT) events among the ten noctuid species and at least three HTT events between the nine Noctuidae species and 11 non-noctuid arthropods. One of HTT events caused by a Gypsy transposon might have caused the recent expansion of Gypsy subfamily in the S.exigua genome. By determining the TE content, dynamics, and HTT events in the Noctuidae genomes, our study emphasized that TE activities and HTT events had substantial impacts on the Noctuidae genome evolution.

River estuaries are dynamic and complex ecosystems influenced by various natural processes, including climatic fluctuations and anthropogenic activities. The Pearl River estuary (PRE), one of the largest in China, receives significant land-based pollutants due to its proximity to densely populated areas and urban development. This study aimed to characterize the composition, diversity, and distribution patterns of sediment microbial communities (Bacteria, Archaea, and Eukaryotes) and investigated the connection with environmental parameters within the PRE and adjacent shelf. Physicochemical conditions, such as oxygen levels, nitrogen compounds, and carbon content, were analyzed. The study found that the microbial community structure was mainly influenced by site location and core depth, which together explained approximately 67% of the variation in each kingdom. Sites and core depths varied in sediment properties such as organic matter content and redox conditions, leading to distinct microbial groups associated with specific chemical properties of the sediment, notably C/N ratio and NH4+ concentration. Despite these differences, certain dominant taxonomic groups were consistently present across all sites: Gammaproteobacteria in Bacteria; Bathyarchaeia, Nitrososphaeria, and Thermoplasmata in Archaea; and SAR in Eukaryota. The community diversity index was the highest in the bacteria kingdom, while the lowest values were observed at site P03 across the three kingdoms and were significantly different from all other sites. Overall, this study underscores the critical role of microbial communities in shaping biogeochemical processes in estuarine environments and their sensitivity to environmental changes, providing valuable information for managing and preserving the health of estuaries and coastal ecosystems.

To analyse Xuanwei ham flavour quality at different post-ripening times, and to elucidate its microbial diversity, we studied free amino acids and volatile flavouring compounds (VOCs) and their relationships. We determined microbial community changes in Xuanwei ham at 1, 2, 3 and 4 years (W1-4) by high-throughput sequencing, and simultaneously, VOCs and free amino acid contents by gas chromatography-mass spectrometry (GC-MS) and liquid chromatography (LC), respectively. Then heatmap analysis was used to determine correlations between microbial communities, free amino acids and VOCs. A total of 25 free amino acids were detected, among which W3 contained the fewest and most were generally lower than in hams in the other three years. Fifty-nine VOCs were detected, among which were 17 esters, and the highest ester content was found in W4. Atotal of 87508391 reads were obtained from the samples, of which 812844 were clean reads, and the bacterial Chao1 index and Shannon index were significantly higher in W3 than in the other three ham years. In differetly-aged Xuanwei hams, Pseudomonadota was the dominant bacterial phylum, and the most abundant genera were Sarocladium, Klebsiella and Vibrio. Klebsiella was the most abundant genus in W1, and Vibrio in W3, and the second most abundant genera were Sarocladium and Gammaretrovirus. We elucidated differences in Xuanwei ham microflora structures in different years and the main flavor-related microorganisms, thus providing a theoretical basis for subsequent Xuanwei ham storage, quality and improvement.

Over the past couple of decades, Global positioning system (GPS) technology has been utilized to collect large-scale data from travel surveys. As the precise spatiotemporal characteristics of travel could be provided by GPS devices, the issues of traditional travel survey, such as misreporting and non-response, could be addressed. Considering the defects of dedicated GPS devices (e.g., need much money to buy devices, forget to take devices to collect data, limit the simple size because of the number of devices, etc.), and the phenomenon that the smartphone is becoming one of necessities of life, there is a great chance for the smartphone to replace dedicated GPS devices. Although, several general reviews have been done about smartphone-based GPS travel survey in the literature review section in some articles, a systematic review from smartphone-based GPS data collection to travel mode detection has none. The included studies were searched from six databases. The purpose of this review is to critically assess the current literature on the existing methodologies of travel mode detection based on GPS raw data collected by smartphones. Meanwhile, according to the systematic comparison among different methods from data-preprocessing to travel mode detection, this paper could carefully provide the Strengths and Weaknesses of existing methods. Furthermore, it is the crucial step to develop the methodologies and applications of GPS raw data collected by smartphones.

Cellular substructure has been widely observed in the sample fabricated by laser powder bed fusion, while its growth direction and the crystallographic orientation have seldom been studied. This research tries to build a general model to construct the substructure from its two-dimensional morphology. All the three Bunge Euler angles to specify a unique growth direction are determined, and the crystallographic orientation corresponding to the growth direction is also obtained. Based on the crystallographic orientation, the substructure in the single track of austenitic stainless steel 316L is distinguished between the cell-like dendrite and the cell. It is found that, with the increase of scanning velocity, the substructure transits from cell-like dendrite to cell. When the power is 200 W, the critical growth rate of the transition in the single track can be around 0.31 ms^-1.

Heat stress is a serious threat to tomato production. The ultrastructure and element mapping of tomato chloroplast were investigated under different nitrogen levels to explore the regulatory effect of nitrogen on tomato chloroplast under heat stress. Experiments design two temperature treatments (25°C/15°C, as control, 40°C/30°C, as severe high-temperature, SHT ) and four nitrogen levels (0.0 kg hm-2, N1; 187.5 kg hm-2, N2; 250 kg hm-2, N3, as recommended nitrogen-application; 312.5kg hm-2 , N4) for a duration of 5 days in artificial climate chamber. The results showed that heat stress led to obvious damage to the ultrastructure of tomato chloroplast, including thylakoid stacking disorder, granum destruction, and starch grain aggregation and degradation. With the increase of nitrogen level, the ratio of long and short axes of tomato chloroplasts increased, the differentiation of chloroplasts was strengthened, the number of plastoglobuli was increased and aggregated, and the degree of damage to the ultrastructure of chloroplasts was reduced. The regulatory effect of nitrogen on the ultrastructure of tomato chloroplasts under heat stress was mainly reflected in the phosphorylation degradation process of starch granules in chloroplasts. There are obvious segmentation lines of Ca, P and Cl on both sides of the inner and outer chloroplasts, and enriched in the chloroplasts, which can outline the boundary of the chloroplasts. Element mapping analysis revealed that heat stress significantly increased the contents of calcium, phosphorus and chlorine in the chloroplast of tomato leaves, while the contents of potassium was decreased. The application of nitrogen fertilizer could significantly regulate the element distribution of tomato chloroplast under heat stress, especially the regulation of phosphorus, chlorine, calcium, magnesium. These results provide new insight into the role of nitrogen using TEM-EDX mapping in the protection of tomato chloroplast under heat stress and the mechanism of heat stress tolerance in plants.

Medical image analysis is an important branch in the field of medicine, which mainly uses image processing and analysis techniques to interpret and diagnose medical image data. Medical image data helps doctors to effectively observe and diagnose patients' body structures, tissues and lesions. Medical image analysis has been an important research area in the medical field, and it is important for disease diagnosis, treatment planning, and condition monitoring. In recent years, the rapid development of deep learning and computer vision technologies has contributed greatly to the automation, multimodal data fusion, real-time application, and accuracy improvement of medical image analysis. In addition, the development of deep learning has given rise to some new research areas in medical image analysis, such as Generative Adversarial Networks (GANs) for synthetic medical images, self-supervised learning for unsupervised feature learning, and neural network interpretability. In this paper, we will introduce some optimisation methods for medical images which are effective in improving the accuracy, efficiency and reliability of medical image analysis.

The Eastern Kunlun Fault Zone (EKFZ) is located in a seismic blank area. This study investigates the hydrogeochemical characteristics of varied-temperature springs in the EKFZ to understand the relationship between fractures, fluids and earthquakes. It aids in establishing their induction mechanisms and assists in monitoring the earthquake precursors of the EKFZ. In this study, the main elements, trace elements, hydrogen and oxygen isotopes and strontium isotopes of 23 varied-temperature springs in the EKFZ were analyzed. The results reveal the source of groundwater recharge, hydrochemical types, mineral saturation, and for a select few springs indicative of geothermal activity, collected geothermal reservoir temperatures. The study also explores the relationship between earthquakes and springs, identifying sensitive chemical indicators. Based on continuous monitoring at Maqu Station, we found that before the occurrence of the Maerkang Ms 6.0 earthquake, the concentration of Cl− rose by 2.9 times, and 46 days before the Gande earthquake (Ms = 4.7), the concentrations of Na+ and SO42− significantly increased. Finally, a conceptual model of the hydrogeochemistry of springs is presented to describe the groundwater circulation in the study area. This research is of great significance for the analysis of fluid geochemistry in this area and for assessing the seismic hazards of the EKFZ.

Matrix asphalt material has poor road performance, which is improved by adding polymer modified agents. The original asphalt material experiment research has a certain limitation in that it cannot truly expose the mechanism and influence of modifiers on asphalt materials. To explore the gain effect of the modified agent on the asphalt material's road performance, the molecular dynamic simulation technology is used to explain its mechanism in the micro dimension. The three parameters of the free volume score, radial distribution function and average directional shift diffusion coefficient are analysed to improve the performance of the modifier on asphalt material, an exploration of the microdimension shows that the amount of SBS modifiers is 6% and the amount of rubber modified asphalt material is 22%. The improvement of materials is better than that of rubber modifiers.

The active power-assist function greatly expands the potential applications of exoskeleton robots, yet the motion intention estimation (MIE) for active power-assist strategy is quite problematic. Through the analysis of the conduction path and the different stage manifestations of motion intention in human body, we confirmed that the joint torque of human body meets the basic requirements of MIE for the active power-assist that we suggest, namely: (i) it reflects the direction and intensity of the wearer’s efforts; (ii) it precedes the human limb motion; (iii) it generates real-time and continuous output. Thus, an online calculation method of human joint torque was proposed. The sensing system integrated in exoskeleton robots was designed to perceive motion data and foot contact force of a human body. A special inverse dynamics with a parameterized model of the human body was proposed. Contrast experiments were carried out with the motion capture system, which results’ accuracy and similarity were evaluated via the root mean square error and correlation coefficient. The comparative analysis of two synchronous results shows good accuracy of the proposed MIE method, which lays the foundation for the realization of active power-assist.

The transforming growth factor-β (TGF-β), in which overexpression have been associated with various diseases, has become an attractive molecular target for the treatment of cancers. Three series of 3-substituted-4-(quinoxalin-6-yl) pyrazoles 14a–h, 15a–h, 16a–h, 22a, 22b, 22d, 23a, 23b, 23d, 24b, and 24d were synthesized and evaluated for their activin receptor-like kinase 5 (ALK5) and p38α mitogen activated protein (MAP) kinase inhibitory activity in an enzymatic assays. Among these compounds, the most active compound 16f inhibited ALK5 phosphorylation with an IC₅₀ value of 0.28 µM, with 98% inhibition at 10 µM. Compound 16f also had good selectivity index of >35 against p38α MAP kinase, with 9.0-fold more selective than clinical candidate, compound 3 (LY-2157299). Molecular docking study was performed to identify the mechanism of action of the synthesized compounds and their good binding interactions were observed. ADMET prediction of good active compounds showed that these ones possess good pharmacokinetics and drug-likeness behavior.

Background: Respiratory syncytial virus (RSV) is a leading cause of acute lower respiratory infection globally. There are vaccines in pipeline to prevent it but a systematic review on immunogenicity and safety of vaccine is lacking. Methods: This systematic review of RSV vaccine clinical trials was undertaken using 4 databases. Searches were conducted using both controlled vocabulary terms such as ‘Respiratory Syncytial Virus, Human’, ‘Respiratory Syncytial Virus Infections’, ‘Respiratory Syncytial Virus Vaccines’, ‘Immunization’, ‘Immunization Programs’ and ‘Vaccines’ and corresponding text word terms. The searches for published papers were limited to clinical trials published from January 2000 to August 6th, 2018. RSV infection case was defined as RSV associated medically attended acute respiratory illness (MAARI) or RSV infection by serologically-confirmed test (Western Blot) during the RSV surveillance period. We calculated the relative risk of each vaccine trial with RSV infection case. Results: Of 4395 publications, 24 were included and data were extracted covering 4 major types of RSV vaccine candidates, these being live-attenuated/chimeric (n=9), recombinant-vector (n=10), subunit (n=1) and nanoparticle vaccines (n=4). For RSV infection cases, 7 trials were involved and none of them showed a vaccine-related increased MAARI during RSV surveillance season. Conclusion: LID ∆M2-2, MEDI M2-2, and RSVcps2 (live-attenuated) were considered the most promising vaccine candidates in infant and children. In the elderly, a nanoparticle F vaccine candidate was considered as a potential effective vaccine. Although no promising vaccine was identified from pregnant-women test, RSV F-024 subunit vaccine candidate and an RSV F nanoparticle vaccine showed encouraging results in healthy non-pregnant women.

Resilience governance provides a new governance model for emergency management in higher education institutions facing major public crises. Higher education resilience governance, while achieving short-term objectives such as mitigating external impacts and maintaining core functions, enhances the enduring adaptability of higher education institutions to the increasingly changing natural and social environments. This transformation shifts the emergency management mode in higher education from reactive responses to proactive governance. In terms of value logic, resilience governance upholds the mission of higher education as the primary nurturing ground, ensuring fairness, quality, and sustainability in education. In terms of organizational logic, it emphasizes collaborative cooperation among higher education institutions, government, society, and the market, as well as the integration of functions within higher education institutions and relatively close connections among their personnel. In terms of institutional logic, it relies on both top-down institutional supply and bottom-up institutional demand to support effective participation, resulting in authoritative and complementary behavioral rules. In terms of action logic, it combines vertical coordination mechanisms and horizontal community collaboration to enhance the effectiveness of cooperative governance. Therefore, the highest value should be placed on the safety of faculty and students, and education planning should be imbued with resilience. It starts with organizational adaptability to develop resilient institutions, focuses on orderly transitions to enhance the emergency management system in higher education, and centers on proactivity and collaboration to build a community of action for emergency governance in higher education.

The goal of this paper is to explore the relationship between the specific non-performing loan ratio (NPL ratio) and the corresponding impact on the bank’s profitability and lending behavior. It also seeks to investigate the macroeconomic impacts of economies with excessively high NPL ratios as well as the efficacy and impact of alleviation measures used by banks and governments around the world to help facilitate a decrease in high NPL ratios. The possible implications and effects of the COVID-19 pandemic on NPL ratios is also addressed in this paper. It is found that when excessively high NPL ratios go unaddressed, the economy tends to suffer. On the other hand, this study shows that when measures are taken to reduce or eliminate the high NPL ratios, economic performance improves, and the reduction has a clear positive impact on the economy.

To study the fermentation process of biocatalyzing decanoic acid to synthesize trans-2-decenoic acid, this study was based on the engineering E.coli constructed in the laboratory in the early stage and studied the effect of seed liquid culture time, culture temperature, inoculum amount, induction temperature, dissolution effects of substrate solvent, metal ions, and substrate loading on the yield of trans-2-decenoic acid. Based on single-factor experimental optimization, the Box–Behnken design was used to conduct response surface testing using the substrate feeding concentration, inducer concentration, and MnCl2 concentration as response variables and trans-2-decenoic acid production as the response value. The optimal fermentation process was determined through experiments: seed culture time 20 h, culture temperature 37°C, inoculation amount 1%, induction temperature 30°C, substrate flow amount 0.15 g/L, inducer concentration 5.60 g/L, MnCl2 concentration was 0.10 mM. Under these conditions, the average production of trans-2-decenoic acid was 1.982 ± 0.110 g/L. Compared with the basic LB medium, the production of trans-2-decenoic acid increased by 1.042 g/L; compared with the previous period, the yield of trans-2-decenoic acid studied increased by 1.501 ± 0.110 g/L, which provides a reliable basis for further research on the fermentation process of biocatalytic decanoic acid synthesis of trans-2-decenoic acid.

The reduction of biodiversity loss is one of the targets of the 2030 Agenda for Sustainable Development. The protection of endangered species is critical for conserving global biodiversity. Asian elephants，as one of the last few mega-herbivores on Earth, are currently threatened by climate changes and anthropogenic modifications. The modelling of their living habitats is of top priority to the conservation of Asian elephant. In this study, we used the maximum entropy model (MaxEnt) to identify the current and potential future habitats of Asian elephants in South and Southeast Asia. We performed analyses for future projections with 17 scenarios by using the present results as baseline. To optimise the modelling results, we delineated the core habitats by using the Core Mapper Tool and compared them with existing protected areas (PAs) through gap analysis. The results showed that the current total area of core habitats is 491,455 km2 in size and will be reduced to 332,544 km2 by 2090 under SSP585 (the shared socioeconomic pathway). The projection analysis under differential scenarios suggested that most of the core habitats in the current protected areas would remain stable and suitable for elephants in the future. However, the remaining 75.17% of the core habitats lay outside the current PAs, and finally we mapped approximately 219,545 km2 of suitable habitats as priority protected areas in the future. Although our model did not perform well in some regions, our analyses and findings still could provide useful references to the planning of protected areas and conservation of Asian elephant.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

(1) Background: Bacterial reinfection and root fracture are the main culprits related to root canal treatment failure. This study aimed to assess the utility of quercetin solution as an adjunctive endodontic irrigant that strengthen root canal dentin with commitment anti-biofilm activity and bio-safety. (2) Methods: Based on a noninvasive dentin infection model, dentin tubules infected with Enterococcus faecalis (E. faecalis) were irrigated with sterile water (control group), and 0, 1, 2, 4 wt% quercetin-containing ethanol solutions. The live and dead bacteria proportions within E. fae-calis biofilms were analyzed using confocal laser scanning microscopy (CLSM). Elastic modulus and hydroxyproline release and X-ray photoelectron spectroscopy (XPS) characterization was tested on irrigant-treated demineralized dentin to evaluate irrigants’ biostability. The cytotoxicity of irrigants was tested by CCK-8 assay. (3) Results: Quercetin increased the proportion of dead bacteria volumes within E. faecalis, and improved the flexural strength of dentin collagen com-pared to control group. The XPS characterization revealed an increase in C-O peak area under both C1s and O1s narrow-scan spectra. The CCK-8 assay confirmed no cytotoxicity of quercetin solutions. (4) Conclusions: Quercetin exhibited anti-biofilm activity, collagen-stabilizing effect as well as cytocompatibility, supporting quercetin as a potential candidate for endodontic irrigant.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Accurate lithium battery diagnosis and prognosis is critical to increase penetration of electric vehicles and grid-tied storage systems. They are both complex due to the intricate, nonlinear, and path-dependent nature of battery degradation. Data-driven models are anticipated to play a significant role in the behavioral prediction of dynamical systems such as batteries. However, they are often limited by the amount of training data available. In this work, we generated the first big data comprehensive synthetic datasets to train diagnosis and prognosis algorithms. The proof-of-concept datasets are over three orders of magnitude larger than what is currently available in the literature. With benchmark datasets, results from different studies could be easily equated, and the performance of different algorithms can be compared, enhanced, and analyzed extensively. This will expend critical capabilities of current AI algorithms, tools, and techniques to predict scientific data.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

The European white birch, scientifically known as Betula pendula, and its variant, B. pendula 'Dalecarlica' are characterized by a serrated leaf margin that enhances their aesthetic appeal. However, the lobed leaf trait can undergo random and spontaneous reversion to the typical ovoid or cordate shape during asexual reproduction. Investigating and elucidating the molecular mechanisms underlying this unpredictable reversion mutation is essential for comprehending the birch leaf development process. In this research, we employed a non-lobed-leaf mutant derived from a lobed-leaf birch clone during plant tissue culture. We adopted a multi-omics approach, including whole-genome resequencing, transcriptome sequencing, and methylation profiling, to analyze and compare genomic variations and gene expression modifications. The study revealed that the 24 variant genes affected by 1464 SNP/InDel sites in the genome of the non-lobed-leaf mutant are not associated with leaf development. While the overall methylation level in the mutant's genome closely resembles that of the serrated-leaf birch, ten genes exhibit differential methylation accompanied by differential expression. Transcriptome sequencing demonstrated that the differentially downregulated genes in the mutant are significantly enriched in the GO:0009733 (response to auxin) and GO:0009734 (auxin-activated signaling) pathways. Validation through McrBC-PCR and qRT-PCR confirmed differential methylation and expression of BpIAA9 in the reversion mutant. The elevated methylation level in the BpIAA9 promoter leads to reduced expression, resulting in changes in the expression of auxin-responsive genes. This, in turn, leads to a transcriptional downregulation enrichment effect in auxin-related pathways in the reversion mutant, ultimately inhibiting the regulation of leaf veins by auxin during their development.

Rural landscapes are acknowledged for their potential to restore human health due to their natural characteristics. However, few studies have systematically analysed the impact of naturalness, landscape types, and combinations of landscape elements on restorativeness using both subjective and objective measurements. This study investigated the restorative effects of various rural landscapes in Guangzhou, employing electroencephalography and eye-tracking technologies to record physiological responses and using the Restorative Components Scale and the Perceived Restorativeness and Naturalness Scale to evaluate psychological responses. The results indicated the following: (1) There was a significant positive correlation between perceived naturalness and restorativeness, surpassing the impact of actual naturalness. (2) Different landscape types had a varying impact on mental health at the equal perceived naturalness. Natural forest landscapes and artificial forest landscapes exhibited the most substantial restorative effects among the natural and semi-natural landscapes examined, respectively, while settlement landscapes showed the highest restorative potential among the artificial landscapes. (3) Restorative properties varied across landscape elements, with identical elements yielding different benefits in different environments. Trees and water significantly enhanced restorativeness, whereas constructed elements such as roads and infrastructure reduced it. This study provides a scientific basis for restorative rural landscape design to enhance mental health and well-being.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

To quantitatively estimate the risk of power system operation under extreme rainfall, a multi-scenario stochastic risk assessment method is proposed. First, a scenario generation scheme considering waterlogged faults of power facilities is constructed based on the storm water management model (SWMM) and the extreme learning machine method. These scenarios will be merged to several typical scenario sets for further processing. The outage of power facilities will induce power flow transfer which may consequently lead to transmission lines’ thermal limit violation. Semi-invariant and Gram-Charlier level expansion methods are adopted to analytically depict the probability density function and cumulative probability function of each line’s power flow. The optimal solution is performed by a particle swarm algorithm to obtain proper load curtailment at each bus, and consequently the violation probability of line thermal violations can be controlled within an allowable range. The volume of load curtailment as well as their importance are considered to quantitatively access the risk of power supply security under extreme precipitation scenarios. The effectiveness of the proposed method is verified in case studies based on the IEEE 24-bus system.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

Biodiversity has long been the main objectives in conservation planning while protecting ecosystem services are rarely concerned with. Protecting ecosystem services are gradually recognized by researchers to be included in conservation planning as its significant benefits to human beings. Currently, the most commonly used protecting strategies only focused on high-value areas so that not all the valuable areas would be protected. Furthermore, there are correlation of trade-off and synergy between ecosystem services, aiming at protecting one ecosystem service may have to sacrifice the conservation effectiveness for others. To ensure all the ecosystem services are adequately protected, spatial explicit relations between all the paired ecosystem services were identified via the calculation of Local Moran’s I, a local scale relationship between ecosystem services were defined and they were classified into 5 kinds of cluster. To alleviate the conflict solutions for multiple ecosystem services goals, we used methodology of Systematic Conservation Planning to identify the priority areas for ecosystem service protection, which act the plan with principles of representativeness, complementarity and persistence. By setting scenarios of optimizing each and all the ecosystem services at the target level from 10% to 90%, we found that positive correlation between each of the 4 ecosystem services occupied large areas in the Yangtze River Basin and all the high-value areas were not congruence in spatial distributions. The optimal conservation spatial pattern showed that the priority areas were quite different when the target level was low. Our results implicated that an integrated conservation planning of achieving objectives of all the ecosystem services is more efficient than superposing multiple planning time after time.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Recently, resistive random access memory (RRAM) has been an outstanding candidate among various emerging nonvolatile memories for high density storage and in-memory computing applications. However, the traditional RRAM, which accommodates two states depending on applied voltage, cannot meet the high density requirement in the era of big data. Many research groups have demonstrated that RRAM possesses the possibility of multi-level cell to overcome the demand of mass storage. Among numerous semiconductor materials, gallium oxide, as the fourth-generation semiconductor material, is highly-profile due to its excellent material proper-ties, and already be widely used in optoelectronics, high-power, resistive switching device and so on, due to its wide bandgap and transparent properties. In this study, we have successfully demonstrated the Al/GO/Ga2O3/ITO RRAM to achieve the possibility of two-bit storage. Compared to the single-layer counterpart, the bilayer structure has excellent electrical properties and stable reliability. The endurance characteristics could be enhanced above 100 switching cycles with an ON/OFF ratio of over 103. Moreover, the filament models are also described in this thesis to clarify the transport mechanisms.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

Molecular dynamics (MD) simulations present a sophisticated nano-scale computational approach that can play a critical role in material design for next generation batteries. One critical piece of information needed for MD simulations is the non-bonded potential parameters, which can be obtained through quantum mechanics (QM) calculations or experimental methods. However, experimental data is not available for exploratory and novel materials to derive the potential parameters. Also, the QM approach needs significant computational power and is too time consuming for large systems. On the other hand, current Artificial Intelligence techniques are faster, but they cannot be generalized across molecules and properties. As a result, there is a significant barrier to discovering and exploring new materials. Overcoming this barrier, in this work, we propose a Machine Learning (ML) based technique that can learn inter-atomic potential parameters for various particle-particle interactions employing QM calculations. This ML model can be used as an alternative for QM calculations for predicting non-bonded interactions in a computationally efficient manner. Using these parameters as input to MD simulations, we can predict a diverse range of properties, enabling researchers to design new and novel materials suitable for various applications in the absence of experimental data. We employ our ML-based technique to learn the Buckingham potential, a non-bonded interatomic potential. Subsequently, we utilize these predicted values to compute the densities of four distinct molecules, achieving an accuracy exceeding 93%. This serves as a strong demonstration of the efficacy of our proposed approach.

Mixed lineage leukemia 1 (MLL1) introduces 1-, 2- and 3-methylation into histone H3K4 through the evolutionarily conserved set domain. In this study, bovine embryonic stem cells (bESCs, named bESCs-F7) were established from the in vitro fertilized (IVF) embryos by Wnt signaling inhibition, while its contribution to endoderm in vivo is limited. To improve the quality of bESCs, MM-102, an inhibitor of MLL1, was applied to the culture. The results showed that MLL1 inhibition along with GSK3 and MAP2K inhibition (3i) at the embryonic stage did not affect bESCs establishment and pluripotency. MLL1 inhibition improves the pluripotency and differentiation potentials of bESCs via up-regulation of stem cell signaling pathways such as PI3K-Akt and WNT. MLL1 inhibition decreases H3K4me1 modification at promoters in bESCs and altered the distribution of DNA methylation in bESCs. In summary, MLL1 inhibition enables bESCs to acquire better pluripotency, and its application may provide high quality pluripotent stem cells for domestic animals.

In heterogeneous networks, the random walks based on meta-path requires prior knowledge and lacks flexibility. And the random walks based on non-meta-path only considers the number of node types, but does not consider the influence of schema and topology between node types in real networks. To solve the above problems, this paper proposes a novel model HNE-RWTIC (Heterogeneous Network Embedding Based on Random Walks of Type & Inner Constraint). Firstly, to realize the flexible walks, we design a Type strategy, which is the node type selection strategy based on the co-occurrence probability of node types. Secondly, to achieve the uniformity of node sampling, we design an Inner strategy, which is the node selection strategy based on the adjacency relationship between nodes. The Type & Inner strategy can realize the random walks based on meta-path, the flexibility of the walks, and can sample the node types and nodes uniformly in proportion. Thirdly, based on the above strategy, a transition probability model is constructed; then, we obtain the nodes embedding based on the random walks and Skip-Gram. Finally, in classification and clustering tasks, we conducted a thorough empirical evaluation of our method on three real heterogeneous networks. Experimental results shown that F1-Score and NMI of HNE-RWTIC outperform state-of-the-art approaches.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

In order to realize the sustainable utilization of water resources and the sustainable development of economy, the evaluation index system of water use efficiency system and economic development system was constructed. Entropy weight method and comprehensive evaluation method were adopted to determine the index weights and conduct comprehensive evaluation for the two systems. The coupling coordination model was used to calculate the coupling degree, coordination degree and coupling coordination degree of the two systems. The annual coupling stage and coupling coordination intensity of the two systems were analyzed and determined. The results showed that the comprehensive evaluation values of both water use efficiency system and economic development system in Jinan City increased greatly from 2008 to 2017, and showed a changing trend of ups and downs. The two systems were in the antagonistic stage, and were gradually approaching the running-in stage, indicating that they were in the state of common development. The coupling coordination degree of the two systems gradually increased in waves, progressed from the moderately to the highly coordinated coupling. In the future, if the water control path appropriate to Jinan City can be explored actively, the water-saving kinetic energy of economic development can be increased constantly, and the linkage effect between economic development and water resources utilization can be given full play to, the two systems will be in the orbit with the benign interaction and healthy harmonious development.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Breeding early-maturing cultivars is one of the most important objectives for pear breeding. Very early-maturing pear provides an excellent parental material for crossing, while the immature embryo and low seed germination of its hybrid progenies often limit the selection and breeding of new early-maturing pear cultivars. In this study, we choose a very early maturing pear cultivar ‘Pearl Pear’ as study object, and investigate the effects of cold stratification, culture medium and seed coat on the germination and growth of early maturing pear seeds. Our results show that cold stratification (4℃) treatment could significantly improve the germination rates of early maturing pear seeds. A 100 days of low temperature pre-treatment and germination on White medium could increase the germination rate up to 84.54%. We also observe that seed coat removal could improve the germination activity of early maturing pear seeds, and middle seed coat removal (MSR) represents an optimal method with its high germination rate and low contamination. The results of our study established an improved protocol for seed germination of early-maturing pear seeds, which will greatly facilitate the breeding of new very early-maturing pear cultivars.

A series of novel sulfonylurea benzothiazoline were designed by splicing active groups and bioisosterism. A solvent-free synthetic route was developed for the sulfonylurea benzothiazoline derivatives via the cyclization and carbamylation. All the compounds were characterized by IR, 1H-NMR, 13C-NMR, HRMS. The biological activity tests indicated the compounds could protect maize against the injury caused by chlorsulfuron to some extent. The molecular docking result showed that the new compound competed with chlorosulfuron to bind with the herbicide target enzyme active site to attain detoxification.

In the note, the authors find several simple and explicit forms for a family of inhomogeneous linear ordinary differential equations studied in "D. Lim, Differential equations for Daehee polynomials and their applications, J. Nonlinear Sci. Appl. 10 (2017), no. 4, 1303-1315; Available online at http://dx.doi.org/10.22436/jnsa.010.04.02".

In the paper, the authors nd a new closed expression for the Fibonacci polynomials and, consequently, for the Fibonacci numbers, in terms of a tridiagonal determinant.

In the paper, by virtue of techniques in combinatorial analysis, the authors simplify two families of nonlinear ordinary differential equations in terms of the Stirling numbers of the first kind.

The heterogeneous structure implies that a few nodes may be crucial in maintaining network structural and functional properties. Identifying these crucial nodes correctly and quickly is a primary issue as contemporarily may face the mushrooming of large-scale datasets. Besides, the ‘weight issue’ is always ignored in this field which edge weight may play a positive/negative role in contributing to the node importance in different weighted networks. This paper provides a novel algorithm, Weighted Expectation Algorithm (WEA), which aims to ensure accuracy and speed of computation by taking advantage of dynamic programming to better handle the task of large-scale networks. Additionally, the weight issue that edge weights may contribute differently is addressed by a simply quantitative definition. Two standard experiments show WEA can maintain the network structure in connectivity well (by the lowest average robustness 0.192) and identify the node importance better in the spreading function test of spreading dynamics (by the highest average Kendall’s tau-b 0.678). In addition, the time complexities of different algo-rithms are evaluated, and their time-consuming are tested, proving that WEA consumes a rela-tively short time.

Background A body composition monitor (BCM) has a role not only in determining over-hydration (OH) but also as an aid to nutritional assessment. For dialysis patient-specific clinical applications of BCM, it is necessary to clarify the relationship between body composition parameters and OH in healthy Chinese individuals. Methods This cross-sectional study involved 314 healthy individuals with a mean age of 45.7±13.1 years. BCM measurements were performed while the subjects were fasting. Results The mean OH level was 0.379±0.81 L. Lean tissue index (LTI) and Lean tissue mass (LTM) were significantly higher in males (p<0.001), while fat tissue index (FTI) was significantly higher in females (p<0.001). In univariate correlation analysis, FTI, Fat, and ATM had a negative correlation with OH in females and all subjects (p<0.05), while LTM and BCM had a positive correlation in all subjects (p<0.05). There was a significant negative correlation between phase angle (PhA) and OH in males, females, and all subjects (r=-0.634, p<0.001; r=-0.666, p<0.001; r=-0.484, p<0.001, respectively). In multivariate linear regression analysis, PhA (b=-1.266, p<0.001), LTM (b=0.987, p<0.001), age (b=-0.307, p<0.001) were independent predictors of OH. Conclusions This study demonstrated that age, LTM and especially PhA, had important roles in predicting OH in healthy Chinese individuals. In the future, PhA may aid in clinical assessment by helping to titrate dry weight among hemodialysis patients with malnutrition.

Cadmium (Cd) is a major heavy metal pollutant and a significant cause of abiotic stress in the environment. Organisms have developed various pathways to protect themselves against Cd stress. MYB protein is a large transcription factor family in plants. Many members of the family have been found to regulate developmental processes and stress responses. However, the function and mechanism of MYB116 are far from clear. In a recent study, we found that MYB116 of Chinese cabbage enhances Cd tolerance in yeast. BrMYB116 is transiently inducible by Cd treatment in Chinese cabbage. When expressed in yeast cells, it enhances tolerance against Cd stress and reduces Cd accumulation in the cells. Further analysis shows that BrMYB116 protein enhances Cd tolerance in yeast cells by activating one target gene that encodes the facilitator of iron transport 3 (FIT3). ScFIT3 is activated through specific binding with its promoter. More importantly, the expression of ScFIT3, leads to a substantial reduction of Cd accumulation in both yeast and Chinese cabbage. This finding implies that a similar network may exist in other biological systems, which presents a promising avenue for enhancing Cd tolerance in plants and developing Cd-resistant crops.

Aborycin is a type I lasso peptide with a stable interlocked structure, offering a favorable framework for drug development. The aborycin biosynthetic gene cluster gul from marine sponge-associated Streptomyces sp. HNS054 was cloned and integrated into the chromosome of S. coelicolor hosts with different copies. The 3-copy gul-integration strains S. coelicolor M1346::3gul showed better production than one-copy or 2-copy gul-integration strains, and the total titer reached approximately 10.4 mg/L, i.e., 2.1 times that of the native strain. Then, five regulatory genes, phoU (SCO4228), wblA (SCO3579), SCO1712, orrA (SCO3008) and gntR (SCO1678), which were reported to have negative effects on secondary metabolism, were further knocked out from the M1346::3gul genome by CRISPR/Cas9 technology. While the ΔSCO1712 mutant showed a significant decrease (4.6 mg/L) and the ΔphoU mutant showed no significant improvement (12.1 mg/L) in aborycin production, the ΔwblA, ΔorrA and ΔgntR mutations significantly improved the aborycin titers to approximately 23.6 mg/L, 56.3 mg/L and 48.2 mg/L, respectively, which were among the highest heterologous yields for lasso peptides in both Escherichia coli systems and Streptomyces systems. Thus, this study provided important clues for future studies on enhancing antibiotic production in Streptomyces systems.

In recent times, there has been significant enthusiasm for the development of all solid state batteries. This interest stems from a dual focus on safety—addressing concerns related to toxic and flammable organic liquid electrolytes—and the pursuit of high energy density. \cite{SCHNELL2018160,Zheng2018}. While liquid electrolyte batteries constitute for now the vast majority of commercial cells, solid electrolyte batteries show great promise. In parallel with experimental research, computational models \cite{GrazioliEtAlCM2016} clarify the several fundamental physics \cite{LiMonroeARCBM2020} that take place throughout battery operations. We review some classical models, emphasizing the conceptual advancements documented in the most recent works.

The possibility of using graphane monolayer crystals as the electrode material is becoming popular. Graphane is stable at room temperature and has large surface area, but its chemical inertness hinders its direct interactions with Li ions. In this study, we performed density functional theory calculations to study the energetic stability, structural and electronic properties of Li on graphane with various CH divacancy configurations (v12, v13 and v14 ). The results show that adsorption of Li atom reduces the formation energy of the CH divacancy configurations. The Li-v12 is most stable with the highest binding energy of 3.25 eV/Li and relaxes to in-plane with other C atoms. Altering the Li charge state to have Li−1-v12 or Li+1 -v12 affects the energetic stability and electronic characters of Li-v12 . The Li−1-v12 (Li +1-v 12 ) enhances (reduces) the binding force between Li and v 12 configuration, and furthermore it improves (deteriorates) the conductivity of the structure. Further investigation of graphane with vacancies is encouraged due to these intriguing observations, as it holds promise for potential utilization as an electrode material.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

Hexabromocyclododecane (HBCD) was most important flame retardant in Expanded Polystyrene foam and Extruded Polystyrene foam in the past forty years in the world. China was the major producer and user of HBCD, and the total HBCD production was about 0.3 million tons. Although HBCD has been completely banned in China in 2021 because of its long-range transport, bioaccumulation and toxicity, there's still a lot of residues in environment. Therefore, we reviewed multiple studies concerning the distribution of HBCD in diverse environmental matrices, such as air, dust, soil, water, sediment and biota. Results revealed that HBCD levels in different environments in China present a geographical variation and were at high level compared with other countries. In all environmental media, relatively high HBCD concentrations have been found in industrial and urban areas. Industrialization and urbanization are two important factors that influence the concentration and distribution of HBCD in the environment. In terms of isomer, γ-HBCD was the dominant isomer in soil, water, and sediment, while in the biota, α-HBCD was the predominant isomer.