Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

Background: Constipation is one of the chronic gastrointestinal functional diseases that affects the quality of life. While Qi Lang Formula (QLF) has demonstrated effectiveness in alleviating constipation symptoms, its precise mechanism remains elusive. Methods: QLF was analyzed using UPLC-MS/MS. Targets for QLF were collected from SwissADME, Herb, ITCM databases, and FC-related targets from scRNA-seq and Genecards databases. Overlapping targets suggested potential QLF therapy targets for FC. Enrichment analysis used the KOBAS database. A "drug-ingredient-target" network was constructed with Cytoscape, and AutoDock verified active component binding. H&E staining assessed colonic mucosa changes, TEM examined ICC structural changes. ELISA measured neurotransmitter levels, and western blot verified QLF's effect on target proteins. ICC proliferation was observed through immunofluorescence. Results: We identified 89 targets of QLF associated with ICC-related FC, with c-Kit emerging as the pivotal target. Molecular docking studies revealed that Atractylenolide Ⅲ, Apigenin, Formononetin, Isorhamnetin, Naringenin, and Ononin exhibited strong binding affinities for the c-Kit structural domain. QLF significantly enhanced first stool passage time, fecal frequency, fecal moisture content, and intestinal propulsion rate. Further analysis unveiled that QLF not only restored neurotransmitter levels but also mitigated colon muscular fiber ruptures. ICC ultrastructure exhibited partial recovery, while RT-qPCR and western blot confirmed upregulated c-Kit expression and downstream targets. Immunofluorescence results indicated ICC proliferation post QLF treatment in rat colon. Conclusion: Our findings suggest that QLF may promote ICC proliferation by targeting SCF/c-Kit and its downstream signaling pathway, thereby regulating intestinal motility.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

We study a two-echelon supply chain made up of a supplier and a manufacturer, both of which can reduce their component/product carbon emissions. With the vertical technology spillovers, we explore the optimal decisions of centralized and decentralized supply chains with price dependent demand and propose coordination strategy for the decentralized supply chain. Considering the cost contraction effectiveness of the technology spillovers, the centralized and decentralized game theoretic models of a two-echelon supply chain are developed to investigate optimal decisions of pricing and carbon emissions reduction. Through a systematic comparison and numerical analysis, we show that the profits of both players and the entire supply chain improve with the effect of technology spillovers increasing. Carbon emissions reduction will be taken by various protective measures so that the supplier and the manufacturer who do not innovate can hardly share the results of innovating via the “free-riding” methods when the technology spillover is relatively small. We also propose a revenue-cost sharing contract through bargaining to enhance the performance of the decentralized supply chain.

Adjunctive treatment of periodontitis lacks solutions allowing enough time for wound healing in the periodontal pockets by avoiding a fast re-colonization. Such a solution might be an antibiotic containing formulation with a controlled release over weeks. Here, a recently described minocycline containing approach is qualified for further clinical development by focusing on proof-of-concept, systemic burden, resistance development and degradation studies. Animal studies were done in two different (mouse-chamber, rat Porphyromonas gingivalis challenging) models, including effects on inflammation markers, bone loss and bone structure. Also, serum concentrations of minocycline after local application were determined by HPLC-MS/MS. The resistance status of bacterial clinical isolates against minocycline was investigated and the degradation of the formulation was characterized by laser scanning- and scanning electron microscopy. Animal studies clearly demonstrated the applicability of the new formulation in the investigated models. Inflammation markers decreased dosage dependent and reduced bone loss compared to non-treated group was observed. Thereby, the systemic burden of the antibiotic was neglectable. Minocycline is still effective against oral pathogens; resistance development was not seen. The biodegradable thread was first swollen and subsequently degraded over weeks. The results support the continued clinical development of this new formulation. A phase I clinical trial is planned to further evaluate its safety and efficacy.

Apiaceae plants have been widely used as traditional Chinese medicines (TCMs) for the treatment of removing dampness, relieving superficies, and dispelling cold, etc. In order to exploit the potential application and improve the yield and quality of Apiaceae medicinal plants (AMPs), The traditional use, phytochemistry, modern pharmacological use, effect of bolting and flowering (BF), and approaches for controlling the BF were summarized. Currently, about 228 AMPs have been recorded as TCMs with 6 medicinal parts, 72 traditional uses, 62 modern pharmacological uses, and 5 main kinds of metabolites. Three effect degrees (i.e., significantly affected, affected to some extent, and no significantly affected) could be classed based on the yield and quality. The BF of individual plants (e.g., Angelica sinensis) could be effectively controlled by the standard cultivation techniques, while the mechanism of BF has not been systemically revealed. This review will provide useful references for the reasonable exploration and high-quality production of AMPs.

Recent studies have been able to detect α-synuclein (αSyn) seeding in formaldehyde-fixed paraffin-embedded (FFPE) tissues from patients with synucleinopathies using seed amplification assays (SAAs), but with relatively low sensitivity due to limited protein extraction efficiency. With the aim of introducing an alternative option to frozen tissues, we developed a streamlined protein extraction protocol for evaluating disease-specific seeding in FFPE human brain. We evaluated the protein extraction efficiency of different tissue preparations, deparaffinizations, and protein extraction buffers using formaldehyde-fixed and FFPE tissue of a single Lewy body disease (LBD) subject. Alternatively, we incorporated heat-induced antigen-retrieval and dissociation using a commercially available kit. Our novel protein extraction protocol has been optimized to work with 10 sections of 4.5-µm-thickness or 2-mm-diameter micro-punch of FFPE tissue that can be used to seed SAAs. We demonstrated that extracted proteins from FFPE still preserve seeding potential and further show disease-specific seeding in LBD and multiple system atrophy. To the best of our knowledge, our study is the first to recapitulate disease-specific αSyn seeding behavior in FFPE human brain, with structural validation. Our findings open new perspectives in re-evaluating archived human brain tissue, extending the disease-specific seeding assays to larger cohorts to facilitate molecular subtyping of synucleinopathies.

Lithium sulfur (Li–S) batteries are expected to be very useful for next-generation transportation and grid storage because of their high energy density and low cost. However, their low active material utilization and poor cycle life limit their practical application. The use of a carbon-coated separator in these batteries serves to inhibit the migration of the lithium polysulfide intermediate and increases the recyclability. We report the extent to which the electrochemical performance of Li–S battery systems depends on the characteristics of the carbon coating of the separator. Carbon-coated separators containing different ratios of carbon black (Super-P) and vapor-grown-carbon-fibers (VGCF) were prepared and evaluated in Li–S batteries. The results showed that larger amounts of Super-P on the carbon-coated separator enhanced the electrochemical performance of Li–S batteries; for instance, the pure Super-P coating exhibited the highest discharge capacity (602.1 mAh g-1 at 150 cycles) with a Coulombic efficiency exceeding 95%. Furthermore, the separators with the pure Super-P coating had a smaller pore structure, and hence limited polysulfide migration, compared to separators containing Super-P/VGCF mixtures. These results indicate that it is necessary to control the porosity of the porous membrane to control the movement of the lithium polysulfide.

To explore the characteristics of the concentric eyewall of a typhoon during its formation and replacement processes, with Super Typhoon Muifa in 2011 as the example case, the Weather Research and Forecast (WRF) mode was used to carry out a numerical simulation to reproduce the entire formation and replacement processes of the concentric eyewall. The physical quantities such as the tangential wind speed, radar echo, radial wind speed, vertical wind speed, and potential vortex were diagnosed and analyzed. The results of the analysis show that the outward expansion of the isovelocity in the lower troposphere was the early signal of the formation of the outer eyewall. After the outer eyewall formed, there was a center of second-highest tangential wind speed in the corresponding area. The second-highest wind speed increased as the strength of the outer eyewall increased, and the position of the second-highest wind speed center was retracted with the retraction of the outer eyewall. The tangential wind speed of the moat area was smaller than that corresponding to the concentric eyewall and this feature gradually disappeared with the increase of the height. The echo in the moat area was weak, and this characteristic was particularly evident when the moat area was relatively wide and the outer eyewall was relatively strong. With the formation and development of the outer eyewall, the intensity of the inflow in the boundary layer corresponding to the inner eyewall was reduced, the intensity of the outflow in the upper layers declined, and the intensities of the inflow and outflow corresponding to the outer eyewall were enhanced. After the second outer eyewall matured, there was a significant inflow in the upper layer of the moat area. Once the outer eyewall formed, a large amount of hydrometeors appeared in the corresponding area, and there was a strong ascending motion inside that area. The strength of the ascending motion and the content of hydrometeors increased as the outer eyewall increased. When the moat area was relatively wide, the divergent airflow generated by the developed outer eyewall in the upper layer would produce a significant descending motion in the moat area.

Numerous dynamic and complicated processes characterize development from the oocyte to the embryo. However, given the importance of functional transcriptome profiles, long non-coding RNAs, single-nucleotide polymorphisms, and alternative splicing during embryonic development, the effect that these features have on the blastomeres of 2-, 4-, 8-, 16-cell, and morula stages of development have not been studied. Here, we conducted a scRNA-seq survey of cells from sheep from the oocyte to the blastocyst developmental stages. We then carried out experiments to identify and functionally analyze the transcriptome profiles, long non-coding RNAs, single-nucleotide polymorphisms (SNPs), and alternative splicing (AS). We founded that between the oocyte and zygote groups significantly down-regulated genes and the second-largest change in gene expression occurred between the 8- and 16-cell stages. We used various methods to construct a profile to characterize cellular and molecular features and systematically analyze the related GO and KEGG profile of cells of all stages from the oocyte to the blastocyst. This large-scale, single-cell atlas provides key cellular information and will likely assist clinical studies in improving preimplantation genetic diagnosis.

Statistical modeling lies at the heart of product design and development throughout numerous engineering disciplines, especially since processing large amounts of data has become increasingly ubiquitous. While mathematical statistics provide elegant guidance pertaining to the question of whether or not some particular underlying modeling assumptions are justified and appropriate, when pursuing a more comprehensive assessment of product design and development other considerations often increase in significance. Therefore, we will examine and analyze the tedious interactions and implications of statistical modeling choices and product liability exposure. To the best of our knowledge, this paper is the first to draw attention to and explore some often overlooked or oversimplified dangers and pitfalls that enter the equation when product design heavily relies on statistical modeling. In particular, through a diligent analysis of both statistical and legal aspects we will explore how statistically optimal procedures may yield far from optimal outcomes in terms of product liability when applied to actual real life problems and why suboptimal nonparametric or robust approaches may constitute better alternatives.

The spillover of the terrorist activities of Boko Haram, a Nigerian jihadi group, into Cameroon’s northern region has resulted in security challenges and humanitarian activity opportunities for Christian churches. The insurgents have attacked and destroyed churches, abducted Christians, worsened Muslim-Christian relations, and caused a humanitarian crisis. Aggregately, these ensuing phenomena have adversely affected Christian churches in this region, triggering an aura of responses: coping strategies, humanitarian work among refugees, and inter-faith dialogue. These responses are predicated on Christianity’s potential as a resource for peace, compassion, and love. In this study we emphasize the role of Christian churches in dealing with the Boko Haram insurgency. It opens up with a contextualization of Boko Haram in Cameroon’s north. This is followed by an examination of the brutality meted out on Christians and church property. The final section is an examination of the spiritual, humanitarian and relief services provided by Christian churches. The paper argues that although Christian churches have suffered at the hands of Boko Haram insurgents, they have engaged in various beneficial responses underpinned by the Christian values of peace and love.

This research analyses extreme precipitation events in the Huaihe River Basin in China, a densely populated region with a history of human settlements and agricultural activities. This study aims to explore the impact of extreme precipitation index changes and provide decision-making suggestions for flood early warning and agricultural development in the Huaihe River Basin. The study utilises the NEX-GDDP-CMIP6 climate models dataset and the daily value dataset (V3.0) from China's national surface weather stations to investigate temporal and spatial changes in extreme precipitation indices from 1960 to 2014 and future projections. At the same time, this study adopted the RclimDex model, Taylor diagram and Sen+Mann-Kendall trend analysis research methods to analyse the data. The results reveal a slight increase in extreme precipitation indices from northwest to southeast within the basin, except for CDD, which shows a decreasing trend. Regarding spatial, the future increase of extreme precipitation in the Huaihe River Basin will show a spatial variation characteristic that decreases from northwest to southeast. These findings suggest that extreme precipitation events are intensifying in the region. Understanding these trends and their implications is vital for adaptation strategy planning and mitigating the risks associated with extreme precipitation events in the Huaihe River Basin.

While the importance of continuous monitoring of electrocardiographic (ECG) or photoplethysmographic (PPG) signals to detect cardiac anomalies is generally accepted in preventative medicine, there remain major barriers to its actual widespread adoption. Most notably, current approaches tend to lack real-time capability, exhibit high computational cost, and be based on restrictive modeling assumptions or require large amounts of training data. We propose a lightweight and model-free approach for the online detection of cardiac anomalies such as ectopic beats in ECG or PPG signals based on the change detection capabilities of Singular Spectrum Analysis (SSA) and nonparametric rank-based cumulative sum (CUSUM) control charts. The procedure is able to quickly detect anomalies without requiring the identification of fiducial points such as R-peaks and is computationally significantly less demanding than previously proposed SSA-based approaches. Therefore, the proposed procedure is equally well suited for standalone use and as an add-on to complement existing (e.g. heart rate (HR) estimation) procedures.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

The e-commerce platform in the digital economy era has evolved into a data platform ecosystem built around data resources and data mining technology systems. The most typical applications of big data are also concentrated in the field of e-commerce. E-commerce companies should first grasp the interactive relationship among the three major factors of data, technology and innovation, e-commerce platform operation is a multidisciplinary research field. It is not easy for researchers to obtain a panoramic view of the knowledge structure in this field. Knowledge graph is a kind of graph that shows the development process and structure relationship of knowledge with the field of knowledge as the object. It is not only a visual knowledge mapping, but also a serialized knowledge pedigree, which provides researchers with a quantitative research method for the development trend of statistics and academic status. The purpose of this research is to help researchers understand the key knowledge, evolutionary trends and research frontiers of current research. This study uses Citespace bibliometric analysis to analyze the data of the Science Net database and finds that: 1) The development of the research field has gone through three stages, and some representative key scholars and key documents have been recognized; 2) the common knowledge mapping of literature The co-occurrence of citations and keywords shows research hotspots; 3) The results of burst detection and central node analysis reveal research frontiers and development trends. Today, the visualization of big data brings different challenges. The abstraction between the world and today's data visualization occurs when the data is captured. Every user sees his own visualization data generated by standardized calculations. At the same time, there are still many controversies in the theoretical model, structure and structural dimensions. This is the direction that future researchers need to further study.

We used the Bootstrap ARDL method to test the relationship between the export trades, FDI and CO₂ emissions of the BRICS countries. We found that China's foreign direct investment and the lag one period of CO₂ emissions have a cointegration on exports. South Africa's foreign direct investment and CO₂ emissions have a cointegration relationship with the lag one period of exports, and South Africa's the lag one period of exports and foreign direct investment have a cointegration relationship with the lag one period of CO₂ emissions. But whether it is China or South Africa, these three variables have no causal relationship in the long-term. Among the variables of other BRICS countries, Russia is the only country showed degenerate case #1 in McNown et al. mentioned in their paper. When we examined short-term causality, we found that CO₂ emissions and export trade showed a reverse causal relationship, while FDI and carbon emissions were not so obvious. Export trade has a positive causal relationship with FDI. Those variables are different from different situations and different countries.

In order to reduce the silique shattering loss of rapeseed mechanical harvesting process, based on the state of force on the silique during rapeseed harvesting reel branch, Ningza 1810, Zhenyou 8 and Fengyou 306 were used as research objects, and the experimental research on the factors affecting rapeseed siliques shattering was carried out using the swing impact method. The experimental analysis showed that: rapeseed varieties, silique moisture content, silique growth position, collision material, impact speed, force position and other factors had significant effects on silique shattering. The impact velocity was less than 1.5m·s-1, the difference on the effect of each factor on pod-shattering was not significant, it was not easy to shatter when the moisture content of rapeseed silique was higher. The impact resistance of the front side of rapeseed was 2 to 4 times that of the bonding surface of rapeseed petals, the shattering rate of the top rapeseed silique was twice that of the bottom siliques, when siliques were supported, they were more likely to shatter under external forces than when they were unsupported. The experimental study of the mechanical properties of rapeseed siliques was carried out using the impending fracture method, the experimental analyses showed that the support position and force position of the silique, the loading speed and the growth position of the silique had a significant effect on the mechanical properties of the silique. The maximum cracking force was higher and bending strength was stronger when the body of the silique was supported, which the range of the maximum cracking force were 3.05N to 4.16N, and the bending strength range were 8.48 MPa to 11.57 MPa. The maximum cracking force and bending strength of the silique was stronger when the front side of the silique petal was pressurized than when the bonding surface of the petal was pressurized. Based on Pearson's correlation and grey correlation analysis, the morphological characteristics of rapeseed siliques were ranked in order of their influence on the performance of siliques in terms of the angle between silique and stalk, stalk diameter, petal thickness, beak length, silique thickness, silique width and silique length. This study can be used as a reference for the design and optimization of the rapeseed harvesting reel branch mechanism and the selection of machine harvestable rapeseed varieties.

As the largest carbon pool on Earth, forest ecosystems are essential to maintaining carbon sink balance. However, accurately estimating the carbon sequestration and carbon storage of forest resources remains an urgent issue to address. Plot investigation, model estimation, and machine learning are examples of current approaches. Nevertheless, because of variables such as regional characteristics and plot size, large-scale and extensive region estimates are comparatively scarce. This study, which focuses on Tianzhu County, aims to comprehensively analyze and estimate the Net Primary Productivity (NPP), carbon storage, and carbon density of the forest ecosystem in this area by integrating data from forest resource inventory and the CASA model. The main conclusions are as follows: (1) The main vegetation types in Tianzhu County include coniferous forests, broad-leaved forests, mixed forests, and shrub forests; (2) Accordin g to the CASA model calculations, the annual cumulative NPP in Tianzhu County in 2020 ranges from a maximum of 249.63 gC/m² to a minimum of 3.40 gC/m², with the forest NPP amounting to 134,674.65 tons of carbon. Based on MODIS observation data, the forest’s NPP is 171,728.32 tons of carbon, with a maximum of 325.36 gC/m² and a minimum of 0.02 gC/m²; (3) At the pixel scale, the carbon storage of forests in Tianzhu County is 361,700 tons. Specifically, 46,500 tons of carbon are stored in coniferous forests, 1,100 tons in broad-leaved forests, 500 tons in mixed forests, and 313,600 tons in shrub forests.

The transforming growth factor-β (TGF-β), in which overexpression have been associated with various diseases, has become an attractive molecular target for the treatment of cancers. Three series of 3-substituted-4-(quinoxalin-6-yl) pyrazoles 14a–h, 15a–h, 16a–h, 22a, 22b, 22d, 23a, 23b, 23d, 24b, and 24d were synthesized and evaluated for their activin receptor-like kinase 5 (ALK5) and p38α mitogen activated protein (MAP) kinase inhibitory activity in an enzymatic assays. Among these compounds, the most active compound 16f inhibited ALK5 phosphorylation with an IC₅₀ value of 0.28 µM, with 98% inhibition at 10 µM. Compound 16f also had good selectivity index of >35 against p38α MAP kinase, with 9.0-fold more selective than clinical candidate, compound 3 (LY-2157299). Molecular docking study was performed to identify the mechanism of action of the synthesized compounds and their good binding interactions were observed. ADMET prediction of good active compounds showed that these ones possess good pharmacokinetics and drug-likeness behavior.

Optical fiber sensors based on tapered optical fiber (TOF) structure have attracted a considerable amount of attention from researchers due to the advantages of simple fabrication, high stability, diverse structures, and have great potential for applications in many fields such as physics, chemistry and biology. Compared with ordinary optical fibers, TOF with their unique structural characteristics significantly improve the sensitivity and response speed of fiber-optic sensors and broaden the application range. This review presents an overview of the latest research status and characteristics of fiber-optic sensors and TOF sensors. Then the working principle of TOF sensors, fabrication schemes of TOF structures, novel TOF structures in recent years, and the growing emerging application areas are described. Finally, the development trends and challenges of TOF sensors are prospected. The objective of this review is to convey novel perspectives and strategies for the performance optimization and design of TOF sensors based on fiber-optic sensing technologies.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Previous study demonstrated the reconstituted type I collagen matrix extracted from rabbit tendons enabled to regenerate the TMJ disc in the rabbit. The aim of this study was to investigate changes in the extracellular matrix (ECM) and mechanisms of regeneration in TMJ disc. In 36 New Zealand rabbits that underwent a partial discectomy, discs were replaced with reconstituted collagen templates for 3 months. A histological analysis showed that moderate to severe degeneration appeared in partially discectomized joints without implantation. In contrast, discs that received the reconstituted collagen template regenerated, and returned to normal to protect the joint. Cells in the regenerative tissue expressed ECM, and fibers became regular and compact due to tissue remodeling over time. Reparative cells differentiated into chondroblasts, and showed highly dense pericellular fibers. The morphology and collagen composition of the disc and condyle in the 3-month experimental group were similar to those of normal tissues. In conclusion, the reconstituted collagen template facilitated the regeneration of surgically discectomized discs. Type I and type II collagens play a crucial role in the regeneration of articular discs.

To realize fast and effective synthetic aperture radar (SAR) deception jamming, a high-quality SAR deception jamming template library can be generated by performing sample augmentation on SAR deception jamming templates. However, current sample augmentation schemes of SAR deception jamming templates face certain problems. First, the authenticity of templates is low due to the lack of speckle noise. Second, the generated templates have low similarity to the target and shadow areas of the input templates. To solve these problems, this study proposes a sample augmentation scheme based on generative adversarial networks, which can generate a high-quality library of SAR deception jamming templates with shadows. The proposed scheme solves the two aforementioned problems from the following aspects. First, the influence of the speckle noise is considered in the network to avoid the problem of reduced authenticity in generated images. Second, a channel attention mechanism module is used to improve the network's learning ability of shadow features, which improves the similarity between the generated template and the shadow area in the input template. Finally, the proposed scheme and the SinGAN scheme are compared regarding the equivalent numbers of looks and the structural similarity between the target and shadow in the sample augmentation results. The comparison results demonstrate that, compared to the templates generated by the SinGAN scheme, those generated by the proposed scheme have targets and shadow features similar to those of the original image, and can incorporate speckle noise characteristics, resulting in higher authenticity, which helps to achieve fast and effective SAR deception jamming.

Abstract: The Micro-Electro-Mechanical System (MEMS) LiDAR point cloud in autonomous vehicles has a large deflection range, which results in slow registration speed and poor applicability. To maximize speed, an improved NDT (Normal Distribution Transform) method that integrates point cloud density features has been proposed. First, the point cloud is reduced using a modified voxel filter and a pass-through filter. Next, the ISS (Intrinsic Shape Signature) algorithm is utilized to analyze the point cloud features and extract keypoints, the 4PCS (4-Point Congruent Sets) algorithm is then employed to calculate the initial pose under the constraints of the keypoint set to complete the coarse registration. Finally, the self-adaptive segmentation model is constructed by using KD-tree to obtain the density features of keypoints, and the NDT algorithm is combined with this model to form an SSM-NDT algorithm, which is used for fine registration. Each algorithm was compared on the autonomous vehicle dataset PandaSet and actual collected data sets, the results show that the novel method increases the speed by at least 60% and takes into account good registration accuracy and strong anti-interference.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Incremental stability analysis for time-delay systems has attracted more and more attentions for its contemporary applications in transportation processes, population dynamics, economics, satellite positions, etc. This paper researches criteria on v(t)-incremental stability, which is defined to demonstrate the convergence rate for incremental stability, for time-delay systems. Firstly, the sufficient conditions for v(t)-incremental stability for time-delay systems with continuous right-hands are studied, and several corollaries for specific cases are provided. As for time-delay systems with discontinuous right-hands, after expounding the relevant conditions for the existence and uniqueness of the Filippov solution, by using approximation methods, sufficient conditions for v(t)-incremental stability are obtained. The conclusions are applied to linear switched time-delay systems and Hopfield neural network system with composite right-hand afterwards.

Our recent study detected the expression of a tissue Renin-Angiotensin System (tRAS) in human intervertebral discs (IVDs). The present study sought to investigate the impact of angiotensin II receptor type 1 (AGTR1) antagonist losartan on human nucleus pulposus (NP) cell inflammation and degeneration induced by tumor necrosis factor-α (TNF-α). Human NP cells (4 donors, Pfirrmann grade 2-3, 30-37 years old, male) were isolated and expanded. TNF-α (10 ng/mL) was used to induce inflammation and degeneration. We examined the impact of losartan supplementation and measured gene expression of tRAS, anabolic, catabolic, and inflammatory markers in NP cells after 24 h and 72 h of exposure, respectively. T0070907, a PPAR-gamma antagonist, was applied to examine the regulatory pathway of losartan. Losartan (1 mM) significantly impaired TNF-α induced increase of pro-inflammatory (nitric oxide and TNF-α), catabolic (matrix metalloproteinases), and tRAS (AGTR1a and Angiotensin Converting Enzyme) markers. Further, losartan maintained the NP cell phenotype by upregulating aggrecan and downregulating collagen type I expression. In summary, losartan showed anti-inflammatory, anti-catabolic, and positive phenotype modulating effects on human NP cells. These results indicate that tRAS signaling plays an important role in IVD degeneration, and tRAS modulation with losartan could represent a novel therapeutic approach.

Ransomware constitutes a distinctive category of pernicious software that sequesters a user's digital assets by encryption, holding them hostage until a sum is extorted from the victim. These incursions have escalated to become among the most prevalent and significant threats confronting both individuals and corporate entities. In combatting this virulent program, dynamic analysis has been established as the favored detection modality. Such analyses typically hinge on Windows API calls, the conduits through which programs requisition services from the operating system. Yet, the superfluous and unrelated Windows API calls interjected by adversaries into the execution stream of suspect binaries precipitate an excessively noisy behavioral sequence, which impairs the performance of counter-ransomware mechanisms. The research outlined herein introduces a novel non-signature-based detection paradigm that harnesses efficacious Windows API call sequences through supervised machine learning strategies. An innovative Enhanced Min Max (EmRmR) filter technique is proposed, aiming to purge noisy features and isolate the most indicative feature subset that encapsulates the ransomware's true behavior. The EmRmR method, diverging from the traditional Min Max approach, circumvents the superfluous calculations that are a hallmark of the conventional algorithms, thereby necessitating a reduced number of evaluations. Additionally, a refinement procedure has been integrated to contract the program's call trace volume by discarding those Windows API calls lacking a robust correlation with ransomware's pivotal behavior. Subsequent to rigorous experimental analyses and juxtaposition with extant behavior-based detection methodologies, the proposed strategy has demonstrated its efficacy in differentiating ransomware behavior, delivering high detection precision alongside a diminution in false-positive occurrences.

Nanoparticle carriers can selectively deliver the drug cargo to tumor cells, thus having the ability to pre-vent early drug release, reduce non-specific cell binding, and prolong in vivo drug retention. We con-structed paclitaxel (PTX)-loaded lipid-shell mesoporous silica nanoparticles (LMSNs) for targeted an-ti-cancer drug delivery. The physical properties of PTX-LMSNs were analyzed by scanning electron mi-croscopy (SEM) and transmission electron microscopy (TEM). The drug loading (DL%) and entrapment efficiency (EE%) of PTX-LMSNs were measured by high performance liquid chromatography (HPLC). In vitro drug release test, in vivo imaging, tissue distribution and pharmacokinetics of PTX-LMSNs were also evaluated. The SEM examination showed that MSNs were sphere, whereas TEM showed that they were rich in fine pores. The uniform core-shell structure of PTX-LMSNs was also verified by TEM. The DL capacity of PTX-LMSN was as high as 21.75%, and PTX was released from the nanoparticles in vitro in a pH-dependent manner. The cumulative amount of free PTX increased at lower pH, which is conducive to selective drug release from LMSNs in the acidic tumor tissues. In vivo imaging showed prolonged reten-tion of PTX-LMSNs, which is beneficial to their therapeutic efficacy. In addition, PTX-LMSNs were primarily concentrated in the liver. Pharmacokinetic experiments showed that the half-life of PTX-LMSNs was 23.21% longer and 79.24% higher than that of Taxol. Together, LMSNs are a highly promising antineoplastic drug carrier system.

It has been an outstanding challenge for global climate models to simulate and predict East Asia (EA) summer monsoon (EASM) rainfall. This study evaluates the dynamical hindcast skills with the newly developed Nanjing University of Information Science and Technology Earth System Model version 3.0 (NESM3.0). To improve the poor prediction of an earlier version of NESM3.0, we have modified convective parameterization schemes to suppress excessive deep convection and enhance insufficient shallow and stratiform clouds. The new version of NESM3.0 with modified parameterizations (MOD hereafter) yields significantly improved rainfall prediction in the northern and southern China but not over the Yangtze River Valley. The improved prediction is primarily attributed to the improvements in the predicted climatological summer mean rainfall and circulations, seasonal march of the subtropical rain belt, Nino 3.4 SST anomaly, and the rainfall anomalies associated with the development and decay of El Nino events. However, the MOD still has notable biases in the predicted leading mode of interannual variability of precipitation. The leading mode captures the dry (wet) anomalies over the South China Sea (northern EA) but misplaced precipitation anomalies over the Yangtze River Valley. The model can capture the interannual variation of the circulation indices very well, but the bias in the circulation-rainfall connection caused predicted rainfall errors. The results here suggest that over EA land regions, the skillful rainfall prediction relies on not only model’s capability in predicting better summer mean and seasonal march of rainfall and ENSO teleconnection with EASM, but also accurate prediction of the leading modes of interannual variability.

Fiber-metal laminates (FMLs) such as Kevlar reinforced aluminum laminate (ARALL), Carbon reinforced aluminum laminate (CARALL), and Glass reinforced aluminum laminate (GLARE) offer great potential for weight reduction applications in automobile and aerospace construction. In order to investigate the feasibility for utilizing such materials in the form of laminates, sheet hydro-bulging tests are studied under the condition of uniform blank holder force for three-layered aluminum and aluminum-composite laminates using orthogonal carbon and Kevlar as well as glass fiber in the middle. The experimental results validate the finite element results and they exhibited that the forming limit of glass fiber in the middle is the highest among the studied materials, while carbon fiber material performs the worst. Furthermore, the crack modes are different for the three kinds of fiber materials investigated in the research. This study provides fundamental guidance for the selection of multi-layer sheet materials in the future manufacturing field.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

Owing to the reduction of rupture instability and the avoidance of wrinkle defect, hydrodynamic deep drawing (HDD) process is gradually becoming attractive for fabricating lightweight and complicated products. Meanwhile, since metallic material presents anisotropic deformation behavior, it is necessary to select an appropriate constitutive model for the prediction of plastic deformation behavior of applied material with high precision. In the present research, several anisotropic yield criteria namely, Hill’48, Yld2000-2d and BBC2005 are implemented to investigate the effect of yield functions on the prediction accuracy of the critical process window and deformation behavior for HDD process of 2024 and 5754 aluminum alloys. Material constants in the yield criteria are determined by applying uniaxial and equi-biaxial tension tests and optimizing an error-function by using the Levenberg-Marquardt algorithm. Furthermore, the process window diagram is computed utilizing the stress analytical model combined material properties with workpiece geometrical features. Numerical simulation results of predicted material anisotropic parameters, process window and HDD deformation for aluminum alloys are compared with the experimental data. Through the comparison of diverse yield criteria based on materials anisotropic coefficients, critical process window prediction, earing profile, and thickness distribution, it is revealed that the Yld2000-2d and the BBC2005 yield criteria can offer more precise models of material behavior in planar anisotropy properties for HDD process of 2024 and 5754 aluminum alloys.

In this paper, we present a full coverage path planning (CPP) algorithm for the marine surveys conducted in the convex polygon shaped search area. The survey is supposed to carry out by torpedo-type AUVs (autonomous underwater vehicles). Due to their nonholonomic mechanical characteristics, these vehicles have nonzero minimum turning radius. For any given polygon shaped search area, it can always be partitioned into one or more convex polygons. With this in mind, this paper proposes a novel search algorithm called CbSPSA (Calculation based Shortest Path Search Algorithm) for full coverage of any given convex polygon shaped search area. By aligning the search inter-tracks alongside the edge with the minimum height, we can guarantee the minimum number of the vehicle’s turns. In addition, the proposed method can guarantee the planned path is strictly located inside the polygon area without overlapped or crossed path lines, and also has the total path length as short as possible. Considering the vehicle’s nonzero minimum turning radius, we also propose a sort of smoothing algorithm to smooth the waypoint path searched by CbSPSA so as for the vehicle to exactly follow it. The smoothed path is also guaranteed to be strictly located inside the polygon. Numerical simulation analyses are also carried out to verify the effectiveness of the proposed schemes.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

This study proposes and validates a novel combustion control system for Oil-Fired Boilers aimed at reducing air pollutant emissions through flame image prediction. The proposed system is easily applicable to existing ships. Traditional proportional combustion control systems supply fuel and air at fixed ratios according to the set steam load, without considering the emission of air pollutants. To address this, a stable and immediate control system is proposed, which adjusts the air supply to modify the combustion state. The combustion control system utilizes oxygen concentration predictions from flame images via SEF+SVM as control inputs, and applies Internal Model Control (IMC)-based Proportional-Integral (PI) control for real-time combustion control. Due to the complexity of modeling the image-based system, IMC parameter tuning through experimentation is essential for achieving effective control performance. Experiments conducted on a 3000 kg/h marine oil-fired boiler in actual operation optimized the controller parameters for stability and responsiveness, and validated their effectiveness. The results demonstrate the potential of the proposed system to improve combustion efficiency and reduce emissions of air pollutants. This study provides a feasible and effective solution for enhancing the environmental performance of marine oil-fired boilers. Given its ease of application to existing ships, it is expected to contribute to sustainable air pollution reduction across the maritime environment.

Background: Hepatocellular carcinoma (HCC) is one of the most prevalent cancers in human populations worldwide. Conversely, Huanglian Decoction is one of the most important Chinese medicine formulas, with the potential to treat cancer. Methods: To identify differentially expressed genes (DEG), we herein downloaded gene expression profile data from the TCGA (TCGA-LIHC) and GEO (GSE45436) databases. We obtained phytochemicals of the four constituent herbs of Huanglian Decoction from the traditional Chinese medicine systems pharmacology database and analysis platform (TCMSP). We also established a regulatory network of DEG and their drug target genes and subsequently analyzed key genes using bioinformatic approaches. Furthermore, we explored the effect of Huanglian Decoction by conducting in vitro experiments so as to verify the prediction. In particular, the CCNB1 gene was knockdown to verify the primary target of this Decoction. Results: Based on the results of network pharmacological analysis, we revealed that there are 5 bioactive compounds in Huanglian Decoction acting on HCC. In addition, our findings confirmed that CCNB1 was the primary key gene, which can be highly expressed in tumors and was significantly associated with a worse prognosis (P = 0.002) according to PPI network analysis of the target genes of these five compounds, as well as expression and prognosis analyses in tumors. We also noted that CCNB1 can be used as an independent prognostic indicator of HCC (P < 0.01). Moreover, in vitro experimental results demonstrate that Huanglian Decoction can significantly inhibit the growth, migration, and invasion of HCC cells. Finally, further analysis showed that this Decoction may inhibit the growth of HCC cells by down-regulating the expression level of CCNB1.

The lower reaches of the Changhua River are located in the northwest of Hainan Island, and the shallow groundwater in this area is the main water source for residents living at both sides of the river. In order to sustain the exploitation and use of water resources in this area, it is essential to clarify the chemical characteristics and the formation mechanism of the groundwater. We collected 100 sets of shallow groundwater samples from the lower reaches of the Changhua River, and analyzed the chemical characteristics of the groundwater in shallow aquifers as well as its controlling factors by means of the methods including descriptive statistical analysis, Piper diagram, Gibbs diagram, and ion ratio. The results show that the overall characteristics of groundwater in the study area are near-neutral to weakly alkaline nature, indicating a generally oxidized environment. The groundwater involves in 56 chemical types, and the most predominant types are Ca•Na-HCO3 and Ca-HCO3, respectively. NO- 3 has become a macro component exceeding SO2- 4in most of the sampling groundwater, suggesting a significant impact of human activities in this area. At the same time, the chemical characteristics of groundwater in the study area are mainly affected by the water-rock interaction, while the water-rock interaction is mostly affected by the dissolution of silicate rocks and less by the dissolution of carbonate rocks and evaporite rocks. According to the ion ratio results, Na+ and K+ in the study area are mainly from the leaching of silicate rocks, Ca2+ and Mg2+ are mainly from the dissolution of carbonate rocks, in addition to a certain degree of cationic exchange. NO- 3 is mainly related to human activities, and the human activities are more affected by agricultural activities and domestic sewage than by industrial and mining activities. This study can provide a reference for the development and protection of shallow groundwater in the lower reaches of the Changhua River.

It is strongly desirable to accurately detect the clouds in hyperspectral images onboard before compression. However, conventional onboard cloud detection methods are not appropriate to all situation such as shadowed cloud or darken snow covered surfaces which are not identified properly in the NDSI test. In this paper, we propose a new spectral–spatial classification strategy to enhance the orbiting cloud screen performances obtained on hyperspectral images by integrating threshold exponential spectral angle map (TESAM), adaptive Markov random field (aMRF) and dynamic stochastic resonance (DSR). TESAM is performed to classify the cloud pixels coarsely based on spectral information. Then aMRF is performed to do optimal process by using spatial information, which improved the classification performance significantly. Some misclassification points still exist after aMRF processing because of the noisy data in the onboard environment. DSR is used to eliminate misclassification points in binary labeling image after aMRF. Taking level 0.5 data from hyperion as dataset, the average overall accuracy of the proposed algorithm is 96.28% after test. The method can provide cloud mask for the on-going EO-1 images and related satellites with the same spectral settings without manual intervention. The experiment indicate that the proposed method reveals better performance than the classical onboard cloud detection or current state-of-the-art hyperspectral classification methods.

A variable speed anti-tangling reel mechanism was designed to address the problems of tangling, hanging and rewinding of the tassel wheel and the high paddling loss in the current Chinese rape combine harvester cutting table. The kinematic equations of the reel mechanism were developed, and the analysis showed that the speed in the entry stage is low and the speed in the exit stage is high, and the attitude of the reel teeth change with the rape plant movement during the whole paddling process. A single-factor test and a multi-factor regression orthogonal combination test were carried out using the cutting table loss rate of rape harvesting as the evaluation index. The main and secondary factors affecting the cutting table loss of the variable speed reel were obtained as the reel speed, the machine travel speed and the ground angle of the frame. A mathematical model of regression of cutter loss and the main influencing factors was established, with the coefficient of determination R2 = 0.9918. The optimal combination of parameters for the variable speed reel was obtained with the lowest cutting table loss rate in rape harvesting as the optimization target: reel speed 25r/min, frame parallel to the ground and implement travel speed 0.7m/s. Field validation tests and comparative tests of cutting table loss of the two reels were carried out. The test results show that the regression mathematical model of the cutting table loss is more accurate, and the cutting table loss is reduced by 13.9% with the variable speed reel compared to the cam-action reel, and there are no problems with the paddle teeth hanging and tangling during the paddling process.

Tree species composition is an important key element for biodiversity and sustainable forest management, and hyperspectral data provide detailed spectral information, which can be used for tree species classification. There are two main challenges for using hyperspectral imagery: a) Hughes phenomena, meaning by increasing the number of bands in hyperspectral imagery, the number of required classification samples would increase exponentially, and b) in a more complex environment, such as riparian mixed forest, focusing on spectral variability per pixel may not be adequate for definability of tree species. Therefore, the focus of this study is to assess spectral-spatial dimensionality reduction of airborne hyperspectral imagery by using minim noise fraction (MNF) transformation, and object-based image analysis (OBIA). An airborne prism experiment (APEX) hyperspectral imagery was used. A study area was a riparian mixed forest located along the Salzach river, and six tree species including Picea abies, Populus (canadensis and balsamifera), Fraxinus excelsior, Alnus incana, and Salix alba were selected. A machine learning algorithm random forest (RF) was used to train and apply a prediction model for classification. Using a spectral dimensionality reduced APEX, a pixel-level classification was also done. According to a confusion matrix, the object-level classification of MNF-derived components achieved the overall accuracy of 85 %, and kappa coefficient of 0.805. The performance of classes according to producer’s accuracy varied between 80% for Fraxinus excelsior, Alnus incana, and Populus canadensis to 90% for Salix alba and Picea abies. Comparison the results to a pixel-level classification, showed a better performance of object-level classification (an overall accuracy of 63% and Kappa coefficient of 0.559 were achieved for pixel-level classification). The performance of classes using pixel-based classification varied 45 % for Alnus incana to 80% for Picea abies. In general, Spectral-spatial complexity reduction using MNF transformation and object-level classification yielded a statistically satisfactory results.

Post-training quantization is pivotal in deploying convolutional neural networks for mobile applications. Block-wise reconstruction with adaptive rounding, as employed in prior works like BrecQ and Qdrop, facilitates acceptable 4-bit quantization accuracy. However, adaptive rounding is time-intensive, and its constraint on weight optimization space curtails the potential for quantization performance. The optimality of block-wise reconstruction hinges on the quantization status of subsequent network blocks. In this investigation, we delve into the theoretical underpinnings of the limitations inherent in adaptive rounding and block-wise reconstruction. Our exploration leads to the development of a post-training quantization methodology, designated as AE-Qdrop. This algorithm operates in two distinct phases: block-wise reconstruction and global fine-tuning. The block-wise reconstruction phase introduces a progressive optimization strategy, superseding adaptive rounding, which not only augments quantization precision but also significantly improves quantization efficiency. To mitigate the risk of overfitting, we introduce a random weighted quantized activation mechanism. During the global fine-tuning phase, we account for interdependencies among quantized network blocks. The weight of each network block will be corrected with logit matching and feature matching. Extensive experiments validate that AE-Qdrop achieves high-precision and efficient quantization. For instance, in the case of 2-bit MobileNetV2, AE-Qdrop outperforms Qdrop by achieving a 6.26% enhancement in quantization accuracy and quintupling the quantization efficiency.

We report on the role of synergistic polarization of Ba0.9Sr0.1TiO3 (BST) nanoparticles in sulfur cathodes to enhance the redox kinetics of polysulfides for high-capacity Li-S batteries. Ferroelectric nanoparticles are known to significantly improve the electrochemical performance of Li-S batteries due to their inherent self-polarization and high adsorption capacity towards polysulfides. X-ray diffraction spectra confirmed the tetragonal symmetry (c/a=1.0073), while Raman spectroscopic analysis validated the presence of tetragonal orientation Raman modes in BST-modified composites. Scanning electron microscope (SEM) images showed a homogeneous distribution of BST in the sulfur cathode system, with grain sizes ranging from 1 to 1.5 μm. Notably, the BST-coupled S50BST30CB10PVDF10 composite cathode achieved a capacity of approximately 820 mAh/g at 100 mA/g, maintaining stability over 100 cycles, demonstrating improved electrochemical performance. Two distinct plateaus between 2.3 V to 2.0 V and 2.0 V to 1.5 V further underscore the superior performance of BST ferroelectric nanoparticles in enhancing the redox kinetics of Li-S batteries. By leveraging the favourable affinity of polar substances towards polysulfides, we aimed to create a more stable reactive environment within the cathodic site, effectively trapping polysulfide intermediates through the synergistic polarization of BST nanoparticles. The synergistic polarization induced by the asymmetric crystal structure of ferroelectrics is anticipated to generate internal electric fields, enhancing chemisorption with heteropolar reactive. The observed high cyclic stability further validates the efficacy of these composite cathodes in mitigating the polysulfide shuttle effect, offering promising prospects for advancing Li-S battery technology.

With the development of economy, maritime transportation has increased rapidly, which has had a significant impact on the marine environment and resources. In recent years, Synthetic Aperture Radar (SAR) has been widely used to observe maritime environmental incident. Through the large coverage area of SAR, marine environmental emergencies, especially oil pollution, can be better monitored and responded to. This study first proposed an improved Full-scale Aggregated MobileUNet (FA-MobileUNet) model to achieve more complete detection results of oil spill areas. The convolutional block attention module (CBAM) in FA-MobileUNet was modified based on morphological concepts. By introducing the morphological attention module (MAM), the improved FA-MobileUNet model can reduce the fragments and holes in the detection results, providing complete oil spill areas which were more suitable for describing the location and scope of oil pollution incidents. In addition, to overcome the inherent category imbalance of the dataset, label smoothing was applied in model training to reduce the model’s overconfidence in majority class samples while improving the model’s generalization ability. The detection performance of the improved FA-MobileUNet model reached 84.55% mIoU (mean Intersection over Union), which was 17.15% higher than that of the original U-Net model. The improved FA-MobileUNet model was then examined by some oil pollution incidents. According to the detection results, if the oil spill was suspected to be caused by a ship, the corresponding Automatic Identification System (AIS) data were collected based on the acquisition time and geo-location of the SAR image to search for the ship suspected of causing oil pollution. Finally, some oil pollution incidents in Taiwan marine area were collected to verify the effectiveness of the proposed model for marine oil pollution monitoring. Experimental results showed that the extent of the detected oil spill was consistent with the oil pollution area recorded in the incident reports.

Kandelia obovata (Ko) and Aegiceras corniculatum (Ac) are common and dominant plant species in mangrove wetlands in South China, and distribute in the similar tidal zones along the coastline. The present study aimed to determine the allelopathic effects of leaf litter leachates (LLLs) from Ko and their purified condensed tannins (PCTs) on the germination and growth of Ac by mangrove microcosms. Replicate pots containing five different levels of LLLs and PCTs were separately prepared and propagules of Ac were placed in each treatment. Both LLLs and PCTs significantly inhibited the germination and growth of Ac, especially in high levels. The final germination rates of roots, stems, and the number of fine roots declined continuously while other growth indicators, including the lengths of fine roots, nutritive roots, the biomasses of roots, stems, leaves, increased firstly and then decreased with increasing levels. These results indicated that LLLs from the leaf litter of Ko, in particular, their PCTs exerted an inhibition effect on propagule germination and seedling growth of Ac, and the inhibitory effects were concentration dependent. This study suggested that condensed tannins from leaf litter, acting as allelochemicals, could regulate the natural regeneration of a mangrove forest.

At the end of the dry season in early March to early April each year, extensive agricultural biomass waste burnings occur throughout insular mainland Southeast Asia. During this biomass burnings period, smoke aerosols blanket the whole regions and were transported and dispersed by predominant westerly and south westerly winds to southern China, Taiwan and as far southern Japan and the Philippines. The extensive and intense burnings coincided with some wildfires in the forests due to high temperature making the region one of the global hot spots of biomass fires. In this study, we focus on the effect of pollutants emitted from biomass burnings in March 2019 at the height of the burnings period to the exposed population and their health impact. The Weather Research Forecast- Chemistry (WRF-Chem) model was used to predict the PM2.5 concentration over the simulating domain and health impacts are then assessed on the exposed population in the four countries of Southeast Asia, namely Thailand, Laos, Cambodia and Vietnam. Using the health impact based on log-linear concentration response function and Integrated Exposure Response (IER), the results show that at the peak period of the burnings from 13 to 20 March 2019, Thailand experienced the highest impact, with an estimated 2170 premature deaths. Laos, Vietnam, and Cambodia followed, with estimated mortalities of 277, 565, and 314 deaths respectively. However, when considering the impact per head of population, Laos exhibited the highest impact, followed by Thailand, Cambodia, and Vietnam. The results highlight the significant health impact and associated economic cost of agricultural waste burnings in Southeast Asia at the end of the dry season. And hence policy makers should take these into account to design measures to reduce the negative impact of widespread burnings on exposed population in the region.

This study utilized panel data from 31 Chinese provinces over a period of nine years to investigate the impact of green finance on the upgrading of the agricultural industrial structure. A fixed-effect model was employed, and the findings indicate that green financing has a positive effect on the growth of China's agricultural industry. However, regional disparities exist, particularly in the uneven distribution of green financing across the eastern, central, and western regions. Moreover, it emphasizes the need to consider regional differences and tailor development strategies accordingly. To promote further development and transformation of China's agricultural industrial structure, the study recommends innovative green financial products, improved regulations and policies, and the integration of digital technologies.

Based on multi-source remote sensing data, scenario analysis, and model simulation, the Pareto optimal solutions for water supply, water purification (N retention), and carbon storage and sequestration services under different scenarios were sought by adjusting its land use structure. The results showed that. In Scenario 1(S1), the water supply service needs to increase by 86.820 to 11.211 billion cubic metres, the water purification (N retention) service needs to decrease by 11,400 to 11,700 tons, and the carbon storage and sequestration service need to decrease by 2.070 to 2.487 billion tons. In Scenario 2(S2), the water supply service needs to increase by 8.243–10.666 billion cubic metres, the water purification (N retention) service needs to decrease by 11,300–1.10 million tons, and the carbon storage and sequestration service needs to decrease by 2.033 to 2.466 billion tons. In Scenario 3 (S3), the water supply service needs to increase by 7.832–11.437 billion cubic metres, the water purification (N retention) service needs to decrease by 1.16–10,800 tons, and the carbon storage and sequestration service needs to decrease by 19.220 to 2.380 billion tons. After land use optimisation and adjustment, the S3 ecological land structure is complete and consistent with the vision of ecological protection and urban development in the study area, which is the optimal scenario. After optimising the S3 ecosystem service supply pattern, the water supply, water purification (N retention), and carbon storage and sequestration services could connect the western and eastern ecosystem service supply areas, balance the overall ecosystem service supply pattern of the study area and meet the demand for ecosystem services. The results can guide regional land planning and ecosystem service management optimisation.

The objective of this study is to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the equivalence ratio distributions and the injected fuel droplet behavior in the cylinder of the RCCI engine. The spray simulation was conducted by dividing two-part. First, the spray validation simulations progressed to find the spray-influenced factor of the test injector. Next, the engine simulations were performed with the spray-influenced factor obtained from spray validation simulations to investigate the effect of the premixed ethanol ratio based on the same total heating value in-cylinder on the injected fuel atomization and the equivalence ratio distributions. The introduced total heating value was fixed at 595J based on the lower heating value of diesel 14mg. The heating value of the premixed ethanol ratio varied from 0% to 40% based on the same total heating value in-cylinder in steps of 10%. It was revealed that when the premixed ethanol ratio based on the same total heating value in-cylinder was increased, the spray tip penetration value was reduced from the time after 4deg of diesel injection start because of the short injection duration by the small amount of diesel fuel. The SMD value was also more enormous up to 32.58% with increasing the premixed ethanol ratio because of the low kinetic energy of the injected fuel by the short injection duration and the slow evaporation of the injected fuel by the low cylinder temperature.

Arthrospira platensis is the widely available source of spirulina and contains distinctive natural pigments including carotenoids and C-phycocyanin (C-PC). In this study, the major carotenoid and C-PC contents were determined in seven commercially available spirulina powder products and laboratory-prepared A. platensis trichomes (AP-1) by an LC-DAD method and a UV-Visible spectrometry, respectively. The correlation of these two pigment content levels with Hunter color coordinates and antioxidant activity was also evaluated. The L* value failed to show a significant correlation with pigment content, but a positive correlation was observed between a* values and the contents of total carotenoid and C-PC. As b* values decreased, the total carotenoid and C-PC contents increased. AP-1 exhibited the highest content of total carotenoids, chlorophyll a and C-PC, and antioxidant activities among the samples. This observation could be related to degradation of these pigments during the mass production process. The carotenoid profiles suggested that the commercial spirulina powders originated from two different sources, A. platensis and A. maxima. Total carotenoid and C-PC content exhibited positive significant correlations with antioxidant activities measured by DPPH and ABTS assays. These results provide a strong scientific foundation for the establishment of standards for the commercial distribution of quality spirulina products.

Multisource meteorological re-analyses are the most reliable forcing data for driving hydrological models to simulate streamflow. We aimed to assess the different hydrological responses through hydrological modeling in the upper Lancang-Mekong River Basin (LMRB) using the two gridded meteorological datasets, climate forecast system reanalysis (CFSR) and the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS). We selected the Pearson’s correlation coefficient (R), percent bias (PBIAS), and root mean square error (RMSE) indices to compare the six meteorological variables of the two datasets. The spatial distributions of the statistical indicators in the CFSR and CMADS, namely, the R, PBIAS, and RMSE values, were different. Furthermore, the soil and water assessment tool plus (SWAT+) model was used to do hydrological modeling based on CFSR and CMADS meteorological re-analyses in the upper LMRB. Different meteorological datasets resulted in significant differences of hydrological responses, which reflected by different sensitive parameters and their optimal value. These different calibrated optimal values of sensitive parameters further lead to the different simulated water balance components between CFSR- and CMADS-based SWAT+ model. These findings can help in a better understanding of the strengths and weaknesses of different meteorological re-analysis datasets and the roles on the hydrological modeling.

A novel fluorescent probe (C460@Tb-MOFs) was designed and synthesized through encapsulating the fluorescent dye 7-diethylamino-4-methyl coumarin into terbium-based metal-organic framework by a simple ultrasonic impregnation method. It is impressive that this dye-modified metal-organic framework can specifically detect styrene and temperature upon luminescence quenching. The sensing platform of this material exhibit great selectivity, fast response and good cyclability toward styrene detection. It is worth mentioning that the sensing process undergoes a distinct color change from blue to colourless, providing conditions for accurate visual detection of styrene liquid and gas. The significant fluorescence quenching mechanism of styrene toward C460@Tb-MOFs is explored in detail. Moreover, the dye-modified metal-organic framework can also achieve temperature sensing from 298 to 498 K with high relative sensitivity at 498 K. The preparation of functionalized MOFs composites by fluorescent dyes provides an effective strategy for the construction of sensors for multifunctional applications.

Utility perceived by individuals is believed to be different from the utility experienced by that individual. System dynamicists implicitly categorize this phenomenon as a form of bounded rationality and traditionally employ a simple smoothing function to capture it. We challenge this generalization by testing it against an alternative formulation of utility perception that is suggested by modern theories of behavioral economics. In particular, the traditional smoothing formulation is compared with the peak-end rule in a simple theoretical model as well as in a medium-size model of electronic health record implementation. Experimentation with the models reveals that the way utility perception is formulated is important and might affect behavior and policy implications of system dynamics models.

The skyrocketing growth in the number of Internet of Things (IoT) devices will certainly pose a huge traffic demand for fifth-generation (5G) wireless networks and beyond. In-band full-duplex (IBFD), which is theoretically expected to double the spectral efficiency of a half-duplex (HD) wireless channel and to connect more devices, has been considered as a promising technology to accelerate the development of IoT. To exploit the full potential of IBFD, the key challenge is how to handle network interference (including self-interference, co-channel interference and multiuser interference) more effectively. In this paper, we propose a simple yet efficient user grouping method, where a base station (BS) serves strong downlink users and weak uplink users and vice versa in different frequency bands, mitigating severe network interference. We aim to maximize a minimum rate among all users subject to bandwidth and power constraints, which is formulated as a highly nonconvex optimization problem. By leveraging inner approximation framework, we develop a very efficient iterative algorithm to solve this problem, which guarantees at least a local optimal solution. Numerical results are provided to show not only the benefit of using full-duplex raido at BS, but also the advantage of the proposed user grouping method.

Estrogen receptor-positive (ER+) breast cancer is common among postmenopausal women and is frequently treated with Letrozole. Letrozole inhibits aromatase from synthesizing estrogen from androgens. Decreased estrogen slows the growth of tumors and can be an effective treatment. Letrozole resistance is increasingly being observed, which poses a unique problem for patients. We reanalyzed transcriptomic data comparing individuals who responded to Letrozole therapy (responders) to those who were resistant to treatment (non-responders). We identified SOX11 and S100A9 as two genes that significantly differed between these patients; with “PLK1 signaling events” being the most significant signaling pathway. We also identified PRDX4 and E2F8 as the top transcriptional biomarkers for ER+ treatment resistance. Many of the other significant gene products play a known role in ER+ breast cancer or other types of cancer, which partially validate our results. Several of the gene products we identified do not have a characterized role in ER+ breast cancer. Our analysis identified a set of genes that warrant further research to elucidate the molecular mechanism of Letrozole resistance in this patient population, as well as novel high-performing biomarkers. We anticipate that these findings could contribute to improved therapeutic outcomes in human patients.

In this study, we provide the Lie symmetries and a classification of plane symmetric static space-times. Based on the invariance of the Lagrange equations of plane symmetries static space-time systems under the transformation Lie group, we provide the Lie symmetry determination equation, Lie symmetry theorem, and the conserved quantity of the systems; by utilizing the Lie symmetry method to solute the system, we give complete classification of the plane symmetric static space-times systems. The research results indicate that using the Lie symmetry method to study plane symmetric static spacetime can identify a series of conserved quantities that exist in the system; Discovered 5 basic Lie symmetries in the system; When the metric parameters of the system are appropriately selected, the plane symmetric static spacetime can have 6, 7, 8, 9, 11, and 17 Lie symmetric symmetries and conserved quantities.

With the spread of compulsory education emerged school management problems continued, and the quality of school management in compulsory education has attracted a great deal of attention in China. However, the application of information technology in the field is not yet detailed and wide, resulting in problems of heavy workload and high difficulty in the whole evaluation process. Accordingly, we use big data technologies such as Apache Spark, Apache Hive, and SPSS to carry out data cleaning, correlation analysis, dynamic factor analysis, principal component analysis, and visual display on 1760 sample data from 40 primary and secondary schools in Q Province in China, and constructs a model school management of quality evaluation in the compulsory education stage, which reduces the 22 management tasks required for previous evaluation to 5, greatly reducing the workload and difficulty of evaluation. It has improved the efficiency and accuracy of evaluation, and further promoted the simultaneous development of education of five domains and education equity in the compulsory education stage.

To investigate the repair mechanism of umbilical cord mesenchymal stem cells (UC-MSCs) in hydrogel on pancreatic β-cells in diabetes, MIN-6 damaged by streptozotocin (STZ) in vitro was used in co-culture with UC-MSCs in hydrogel (UC-MSCs + hydrogel). It was found that UC-MSCs + hydrogel had a significant repair effect on injured MIN-6 cells, which was better than the use of UC-MSCs alone (without hydrogel). After repair, the expression of superoxide dismutase (SOD) and catalase (CAT) as well as the total antioxidant capacity (T-AOC) of the repaired MIN-6 cells were increased, effectively reducing the oxidative stress caused by STZ. In addition, UC-MSCs + hydrogel were able to curb the inflammatory response by promoting the expression of anti-inflammatory factor IL-10 and reducing inflammatory factor IL-1β. In addition, the expression of both nuclear antigen Ki67 for cell proliferation and insulin-related genes such as Pdx1 and MafA was increased in the repaired MIN-6 cells by UC-MSCs + hydrogel, suggesting that the repair effect promotes the proliferation of the injured MIN-6 cells. Compared with the use of UC-MSCs alone, UC-MSCs + hydrogel exhibited longer survival time of UC-MSCs, because the porous structure and hydrophilic properties of the hydrogel could affect the growth of cells and slow down their metabolic activities, resulting in a better repair effect on the injured MIN-6 cells.

Most existing data synthesis methods are designed to tackle problems such as dataset imbalance, data anonymization and insufficient sample size. There is a lack of effective synthesis methods for the limited number of datasets which contain a large of features and unknown noise to expand the size of the dataset. We propose a data synthesis method, named Adaptive Subspace Interpolation for Sample Optimization (ASISO). The idea is to divide the original feature space into several subspaces with an equal number of samples, and then perform interpolation for the samples in the adjacent subspaces. This method can adaptively adjust the size of the dataset containing unknown noise, and the expanded data typically contain minimal error with actual. Moreover, it adjusts the structure of the samples, which can significantly reduce the proportion of samples with large errors. In addition, the hyperparameters of this method have an intuitive explanation and usually require little calibration. Experimental results on artificial data and benchmark data sets demonstrate that ASISO is a robust and stable method to optimize samples.

Psoriasis is a chronic, multisystem, inflammatory disease. The typical clinical cutaneous manifestation of psoriasis is scaly erythema or plaque, limited or widely distributed. However, psoriasis is far beyond the skin involvement and provides many challenges, including associated comorbidities. In this review, we classify psoriasis as cutaneous and systemic psoriasis, according to the clinical diversity and associated comorbid diseases, and recommend classification criteria for psoriasis. The key objective of this novel classification is to raise awareness of the complexity of this multifaceted disease and help to better understand and manage this complex disease comprehensively.

In order to increase the number of tourism in ecotourism, enhance the ecotourism attractions. It is essential to construct the ecotourism service system for the Penghu National Scenic Area because the ecology system is sensitive and frangible. This study adopts the Fuzzy Delphi method and Analytic Hierarchy Process (AHP) to establish an index framework of ecotourism service system of Penghu National Scenic Area. The results indicated that there are 4 dimensions which include 21 factors service attributes are identified as the service system for traveling. The findings are concluded as follows:(1)the security management capability is the main principle for ecotourism service system;(2)the ecological diversity is fundamental for the marine environment and the core resource for ecotourism;(3)the transportation capacity and environmental quality need to improve; (4)the marine environmental resources is the most important item for sound ecotourism development; (5)the enhancement of the operation willingness of local communities can promote ecotourism development;(6)the natural resources should be protected to provide an ideal recreational environment for ecotourism;(7)the development of ecotourism needs to support local conservation to achieve sustainability. The perspectives of sustainability and service system are involved to support the value of this study, which can continuously sustain Penghu archipelago.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

To accurately and non-destructively monitor the growth of spring wheat in the Hetao Irrigation Area, UAV remote sensing was employed during various fertility stages. Digital image indices from diverse fertilization treatments were calculated and compared with physiological indices to identify the most sensitive digital image indices corresponding to these indices. The study underscored the critical importance of the flowering stage in the growth of spring wheat, thus highlighting the necessity of focusing on this stage. This finding reiterated that the flowering stage was pivotal for spring wheat development in the Hetao Irrigation Area. Several digital image indices, such as GLA, R, G, INT, g, GRVI, MGRVI, RGBVI, EXG, and GRRI, exhibited a high frequency of significant correlations with physiological indices during the four primary reproductive stages of wheat. Consequently, these sensitive digital image indices during the flowering stage can more effectively characterize the physiological indices of spring wheat.

In the context of the rural revitalization strategy, it is urgent to accurately grasp the spatial differentiation characteristics and influencing factors of rural settlements in underdeveloped arid inland river basins. Taking the Shiyang River Basin as an example, the rural settlements from 2000 to 2019 were obtained by visual interpretation using satellite remote sensing data and official statistical data. Following the logical of "state characteristics - evolutionary patterns - influence factors - layout optimization", the average nearest index, gravity-center migration model, spatial statistical analysis and other methods were used combine with GIS. The spatiotemporal pattern evolution characteristics of rural settlements in the past 20 years have been analyzed. The results revealed the following: 1) The distribution pattern of rural settlements in the study area is sheet-like and strip-shaped. The projects in the southeast are mostly distributed in a patchy pattern with high density, while the characteristics in the west and north are exactly opposite. The objects in the south are distributed in the alluvial area of rivers, while settlements in the north are located in the oasis area. 2) From 2000 to 2019, the scale of rural settlements in the Shiyang River Basin, where simultaneous occurrence of new-built and disappearing phenomena, shows an expansion trend that fast firstly and then slow. Spatially, rural settlements in the basin show a trend of clustering towards the southwest. 3) The distribution characteristics of rural settlements are close to water and roads, greatly influenced by urban-rural integration and ecological migration. The results will provide scientific basis for accelerating the modernization of rural areas, and the construction of new rural areas according to local conditions.

Five new cembrane-type diterpenes, lobocalines A–E (1–5), and four new steroids, lobocalines F–I (9–12), along with six known related compounds (6–8 and 13–15) were isolated from the Yalong Bay soft coral Lobophytum catalai. The structures of the new compounds were elucidated by extensive spectroscopic analysis, NMR calculation with DP4+ analysis, time-dependent density functional theory-electronic circular dichroism (TDDFT-ECD) calculations, X-ray diffraction analyses, and the comparison with the reported spectroscopic data of known compounds. Further, with the aid of X-ray diffraction analysis, the structure of lobocrasol B (15) was firmly revised as 15a. In in vitro bioassays, compound 2 showed moderate antibacterial activities against fish pathogenic bacteria Streptococcus parauberis KSP28 and Phoyobacterium damselae FP2244 with minimum inhibitory concentration (MIC) values of 8.7 and 17.3 µg/mL, respectively. All the steroids exhibited antibacterial activities against the S. parauberis KSP28 with MIC values ranging from 12.3 to 53.6 µg/mL. Compounds 2, 7 and 14 have remarkable inhibitory effects on the hemolysin production of Staphylococcus aureus, while compounds 8–12 have medium inhibitory effects on the pyocyanin production in Pseudomonas aeruginosa.

Environmental, social, and governance (ESG) investment has become a common trend in capital markets, and many institutional investors have publicly declared their long-term ESG investment target (ESGIT). This study focuses on investors who conduct strategic asset allocation (SAA) using composite indices but establish their ESGIT outside the SAA process. A mismatch could arise between investors’ planned and actual portfolios because they must pursue their ESGIT by asset selection, which inevitably makes the constituents of their portfolios different from those of composite indices. To scrutinize the potential existence of a misalignment between their SAA and ESGIT, this study analyzes actual stock and bond indices over the past decade using traditional mean-variance optimization. The results reveal significant differences between the expected and realized performances, and the misalignment is more significant when the analysis period is divided into two sub-periods: stable and volatile. Specifically, the results indicate that the efficient frontier constructed using ESG indices significantly differs from that constructed using composite indices, and that the difference between these two efficient frontiers becomes more significant during volatile periods. Furthermore, the results show that investors cannot meet their targets if their ESGIT is established outside the SAA process.

The shortwave infrared Ge-Si photodetector will become the core device of the LiDAR optical receiver. In order to meet the urgent demand for photodetectors in the LiDAR field, we have designed and produced a 32×32 pixel Ge-Si photodetector array proposed and developed to meet the performance requirements of the detector array. A dark current detection system for fast scanning and detecting large-scale Ge-Si detector arrays is proposed and developed to achieve rapid detection of dark current in each pixel of the detector. The system was used to validate the main performance indicators of the detector array we designed, achieving rapid discrimination of array performance and rapid localization of damaged pixels. The scanning test results show that the average dark current of the detector array chip we designed is at the nano ampere level, and the proportion of bad points is less than 1%. The consistency of the array chip is high, which can meet the requirements of light detection at the receiving end of the LiDAR. This work laid the foundation for our subsequent development of a LiDAR prototype system.

Mining and processing tailings often contain significant amounts of valuable metals, that can represent valuable sources of secondary raw materials. Especially this is case in early-stage operations, in which the head grades were higher, and the tailings were higher grade. These tailings can also present a substantial risk to the environment. Serbia has copper deposits which have been exploited since ancient times, and these operations have generated large amounts of mineral processing tailings. The main objective of this study is to show how valuables can be recovered from chemically and mineralogically challenging tailings. After detailed chemical and mineralogical characterization, the laboratory scale flotation tests focused on evaluating the effect of particle size, different types of collectors, pH, and pulp potential. Based on the test work, copper and gold can be recovered effectively into pyrite concentrate

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

Long-span steel structure trusses are widely used in factory buildings, but with the growth of service time and the increase of dynamic load fatigue, a considerable part of the long-span truss with dynamic load appears serious transverse cracks at the bottom of the middle span and oblique deformation of the abdomen in the operation process. The U-shaped cracks at the bottom and belly, as well as the mid-span down deflection of the main truss, reduced the functional function of the factory building truss structure, and had to limit the original crane load, which affected the normal safety and durability of the structure. Therefore, the application principle of the variable axial force cable system in the long-span factory building truss structure and 3D3S software modeling [1] were used. Analyzing and studying the reinforcement method of large-span powerhouse truss can provide practical experience for subsequent similar projects. In view of the above phenomenon, the large-span powerhouse trusses of Hongcheng Powerhouse 1 and No.2 located in Tonglu, Zhejiang Province are used as the research object, and the variable axial force cable method is proposed to strengthen and lift the load. Considering the span of large-span powerhouse truss, the cable system with 22m controlling force of 400kN is proposed to be selected for powerhouse 1, and the cable system with variable axial force of 24m is proposed to be selected for Powerhouse 2. The force model of large-span truss is established by using the finite element method commonly used to analyze the force of truss. Under two working conditions, The influence of reinforcement effect is analyzed and compared from three aspects: stiffness, bearing capacity and stability. And the phenomenon of uneven stress distribution is analyzed. The stress distribution characteristics of each node are understood by simulating the most disadvantageous node plates with the greatest internal force before and after reinforcement.

Evidence indicates that the long noncoding RNAs are involved in the metformin-mediated anti-cancer processes. However, the potential effects of the long noncoding RNAs in metformin-mediated anti-tumor processes in esophageal squamous cell carcinomas (ESCC) are still elusive. This study uncovered that metformin decreases the level of long noncoding RNAs CCAT1 and SPRY4-IT1 thereby contributing to the down-regulation of c-Myc and vimentin. Also, the RNA level test of human ESCC tissue confirmed the positive correlation between CCAT1 and c-Myc. These findings demonstrated that metformin facilitated anti-cancer effects by targeting the 2 long noncoding RNAs (CCAT1 and SPRY4-IT1) and their consequential targets c-Myc and vimentin. Therefore, the CCAT1 and SPRY4-IT1 might act as novel molecular targets that mediate the anti-tumor effects in esophageal squamous cell carcinoma. This helps in predicting the treatment response of metformin in patients diagnosed with esophageal squamous cell carcinoma.

Immune checkpoint blockade (ICB) has revolutionized the prognosis of several advanced-stage solid tumors. However, its success has been far more limited in hematological malignancies and is mostly restricted to classical Hodgkin lymphoma (cHL) and primary mediastinal B cell lymphoma (PMBCL). In patients with non-Hodgkin lymphoma (NHL), response to PD-1/PD-L1 ICB monotherapy has been relatively limited, although some subtypes are more sensitive than others. Numerous predictive biomarkers have been investigated in solid malignancies, such as PD-L1 expression, tumor mutational burden (TMB) and microsatellite instability (MSI), among others. This case-illustrated review aims to appraise the current knowledge on PD-1/PD-L1 ICB efficacy in lymphoid malignancies, when used either as monotherapy or combined with other agents, and describes potential biomarkers of response in this specific setting.

Reconstruction of acoustic relaxation absorption curve is a powerful approach to ultrasonic gas sensing, but requires known of a series ultrasonic absorption at various frequencies around effective relaxation frequency. Ultrasonic transducer is a most widely deployed sensor for ultrasonic wave propagation measurement and works only at a fixed frequency or specific environment like water, so a large number of ultrasonic transducers operating at various frequencies are required to recover an acoustic absorption curve with a relative large bandwidth, which cannot suit for large-scale practical applications. This paper proposes a wideband ultrasonic sensor using a distributed Bragg reflector (DBR) fiber laser for gas concentration detection through acoustic relaxation absorption curve reconstruction. With a relative wide and flat frequency response, the DBR fiber laser sensor measures and restores a full acoustic relaxation absorption spectrum of CO2 using a decompression gas chamber between 0.1 and 1 atm to accommodate the main molecular relaxation processes, and interrogates with a non-equilibrium Mach-Zehnder (M-Z) interferometer to gain a sound pressure sensitivity of -45.4 dB. The measurement error of the acoustic relaxation absorption spectrum is less than 1.32%.

Fullerene nanomaterials exposure often causes a variety of diseases. Many studies have pointed out that fullerene nanomaterials can be studied in fish. However, there are few studies on health risk assessment of clownfish with lower doses of fullerene nanoparticles or different exposure durations. In this study, we set 1.5% and 3.0% for low- and high-dose fullerene nanomaterials exposure concentrations, respectively. Meanwhile, we performed a time-series analysis to investigate that the activation of lipid and amino acids metabolism after fullerene nanomaterials exposure in clownfish. 1368 metabolites were detected from clownfish by using liquid chromatography-mass spectrometry (LC-MS) analyses. Our results suggest that exposure to lower fullerenes nanoparticles may have a certain promoting effect on clownfish overall length, body length and weight. At the same time, the activation of potential metabolic pathways enriched by different metabolites in KEGG pathway may also indicate the positive promoting effect of fullerene nanoparticles after exposure. The present work indicates that it is particularly important to find the concentration window for fullerene nanomaterials to improve government safety guidelines, especially when these are applied to assess the health risk of human.

Load variations in any power system result in losses escalation and voltage drops. With the sensible and optimal allocation of distributed generators (DGs), these problems could be considerably mitigated. It has been seen in the priorly existing methods that ideally allocation of DGs has been carried out during fixed loads and constant power requirements. However, in real scenarios the loads are always variable and allocation of DGs must be done in accordance to the variations of the connected load. Therefore, the current paper addressed the aforementioned problem by distinctive optimal allocation of DGs for each variability of 24hour load horizon. However, the single exclusive solution is considered among all allocations of 24 hours. The min-max regret concept has been utilized in order to deal with such methodology. Altogether, 24 scenarios are analyzed wherein each scenario corresponds to a specific hour of the respective day. The optimal allocation of DGs in terms of their optimal sizing and placement has been carried out by using three algorithms including battle royal optimization (BRO), accelerated particle swarm optimization (APSO) and genetic algorithm (GA). The multi-objective optimization problem is evaluated on the basis of minimum value criterion of the multi-objective index (MO). MO comprises of active and reactive power losses and voltage deviation. Hence, in order to find robustness of proposed technique, Conseil international des grands réseaux electriques (CIGRE’s) MV benchmark model incorporating 14 buses has been considerably used as a test network. In the end the results of three proposed algorithms have been compared.

Jellyfish search (JS) algorithm impersonates the foraging behavior of jellyfish in the ocean. It is a new developed meta-heuristic algorithm that solves complex and real world optimization problems. The global explore capability and robustness of JS are strong, but JS still has great development space in solving complex optimization problems with high dimensions and multiple local optima. Therefore, an enhanced jellyfish search (EJS) algorithm is developed in this study, and three improvements are made: (i) By adding sine and cosine learning factors, the jellyfish can learn from both random individual and best individual during Type B motion in swarm to enhance the optimization capability and convergence speed; (ii) Adding local escape operator can skip local optimal trap and boost the exploitation ability of JS; (iii) Opposition-based learning operator and quasi-opposition learning operator can increase and strengthen the population distribution more diversified, and better individuals are selected from present and new opposition-solution to participates in the next iteration, which can boost the solution’s quality, meanwhile convergence speed is fasted and its precision is increased. In addition, the performance contrast of the developed EJS and some previous outstanding and advanced methods are evaluated on CEC2017, CEC2019 test suite and six real engineering example of case. It is demonstrated that EJS algorithm escaped the trap of local optimum, enhanced the solution’s quality and the calculation speed. What’s more, the practical engineering applications of EJS algorithm also verify its superiority and effectiveness in solving both constrained and unconstrained optimization problems, and it stretched one’s mind for solving such optimization problems.

Research conducted on individuals with depression reveals that major depressive disorders (MDDs) coincide with diminished levels of the inhibitory neurotransmitter γ-aminobutyric acid (GABA) in the brain, as well as modifications in the subunit composition of the primary receptors (GABAA receptors) responsible for mediating GABAergic inhibition. Furthermore, there is substantial evidence supporting the significant role of GABA in regulating stress within the brain, which is a pivotal vulnerability factor in mood disorders. Although there is substantial evidence indicating that GABA may be affecting GABA receptors in peripheral tissues, there is comparatively less evidence supporting its direct action within the brain. Emerging evidence highlights that GABA may exert beneficial effects on the brain and psyche through the gut-brain axis. GABA is readily available and approved as a food supplement in many countries. While GABA enjoys wide consumer acceptance in Eastern Asian markets, with many consumers reporting favorable effects on stress regulation, mood, and sleep, rigorous independent research is still largely lacking. Basic research, coupled with initial clinical findings, makes GABA an intriguing neuro-nutritional compound deserving of clinical studies in individuals with depression and other psychological problems.

Juvenile hormones (JH) play crucial roles in insect development, reproduction, and other physi-ological functions. Because JH is specific to arthropods, including insects, it has long been stud-ied for use in pest control. Accordingly, this study aimed to identify the substances that act as JH disruptors from edible plants. Curcuminoids generally exhibit a wide range of biological ac-tivities, such as antioxidant, anti-inflammatory, antibacterial, and insecticidal properties, and they exhibit insect growth inhibitory effects. Demethoxycurcumin and bisdemethoxycurcumin, two curcuminoids from the turmeric plant Curcuma longa L. inhibit the formation of a metho-prene-tolerant (Met)–Taiman (Tai) heterodimer complex as shown through in vitro yeast two-hybrid assays. An artificial diet containing 1% (w/v) demethoxycurcumin or bisdemethox-ycurcumin reduced the number of larvae, leading to no pupal development. Building on our re-sults regarding curcuminoids, researchers can use our study as a reference to develop eco-friendly pesticides.

Plant-derived compounds have been historically used for the treatment of various diseases and an important source of several clinically useful anti-cancer agents. The Artemisia annua is known as a medicinal herb that is effective against cancer. Thus, the purpose of this study was to investigate whether ethanol extracts of Artemisia annua could increase an anti-cancer effect against LS174T cells. Our results show that Artemisia annua extracts (AAE) induces apoptosis through the regulation of mitochondria outer membrane potential. We demonstrate that apoptosis is induced by p53-dependent manner when cells were treated with Nutlin-3 (MDM2 inhibitor) and LY294002 (Akt inhibitor). In addition, the apoptotic effect was also observed in the p53-independent manner through pifithrin-α (p53 inhibitor) and celecoxib (COX-2 inhibitor) treatment. As in in vitro, AAE induced apoptotic effects and regulated apoptosis-related proteins in LS174T xenograft model. Taken together, these results suggest that Artemisia annua extracts exerts an anti-cancer effect through p53-independent manner, as well as p53-dependent manner by p53´ translocation in LS174T colon cancer cells.

This study investigates job satisfaction, burnout, and well-being among first-generation migrant physicians in anesthesia and intensive care medicine in Germany, comparing them to their native German counterparts. Utilizing a cross-sectional survey design, the study collected data from 513 physicians, 110 of whom identified as having a migration background. Job satisfaction was measured using the German version of the Warr-Cook-Wall (WCW) Job Satisfaction Scale, burnout was assessed with the Copenhagen Burnout Inventory (CBI), and well-being was evaluated using the WHO-5 Well-Being Index. The job satisfaction ratings revealed no significant differences between migrant and German physicians in most dimensions, including physical workload, freedom to choose work methods, satisfaction with colleagues, responsibility, income, skill utilization, and variety in work tasks. However, migrant physicians reported significantly higher satisfaction with recognition received for their work and lower dissatisfaction with working hours. Burnout assessments showed that migrant physicians experienced higher psychological strain, perceiving every work hour as more exhausting and having significantly less energy for family and friends. Notably, migrant physicians reported higher difficulty and frustration in working with patients. Well-being ratings indicated that migrant physicians felt less energetic and active but found their daily life more filled with interesting activities. The findings underscore the unique challenges faced by migrant physicians, particularly in terms of recognition and patient-related burnout. These results highlight the need for targeted interventions to support migrant physicians, including cultural competence training and flexible working hours to enhance their job satisfaction and overall well-being. Addressing these issues is crucial for maintaining the quality of patient care and the occupational health of migrant physicians in Germany.

Although hydrogen gas (H2) treated soil improves crop biomass, this approach appears difficult for the field application due to the flammability of H2 gas. In this report, we investigated whether and how H2 applied in hydrogen nanobubble water (HNW) improves the yield and quality of cherry tomato (Lycopersicon esculentum var. cerasiforme) with/without fertilizers. Two-year field trials showed that compared to corresponding controls, HNW without/with fertilizers improved cherry tomato yield per plant by 39.7% and 26.5% in 2021 (Shanghai), and 39.4% and 28.2% in 2023 (Nanjing). Compared to surface water (SW), HNW increased soil available nitrogen (N), phosphorus (P), and potassium (K) consumption regardless of fertilizer application, which may be attributed to the increased NPK transport related genes in roots (LeAMT2, LePT2, LePT5, and SlHKT1,1). Also, HNW-irrigated cherry tomato displayed higher sugar-acid ratio (8.6%) and lycopene content (22.3%) than SW-irrigated plants without fertilizers. Importantly, the beneficial effects of HNW without fertilizers on yield per plant (9.1%), sugar-acid ratio (31.1%), volatiles (20.0%) and lycopene contents (54.3%) were stronger than those achieved by fertilizers alone. In short, this study clearly indicated that HNW-supplied H2 not only exhibited fertilization effect on enhancing tomato yield, but also improved fruit quality with a lower carbon footprint.

In this review, we present the latest exclusion limits obtained with astroparticles for Lorentz Invariance Violation (LIV) in the photon sector. We discuss the techniques known as energy-dependent time delay or time lag, subluminal pair production threshold shift, superluminal photon decays and superluminal photon splitting. Perspectives for future results in LIV with the next generation of experiments are also addressed.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.

Monin-Obukhov similarity theory (MOST) overestimates wind shear in some atmospheric stable conditions, i.e. Richardson number $R_f<0.25$. The overestimated wind shear that leads to an under-predicted friction wind speed and a lower ambient turbulence intensity for a given hub-height reference wind speed and a given roughness length, could influence wake modeling of a wind turbine. This work investigates the side effects of the breakdown of MOST on wake modeling under stable conditions and makes some modifications to the flow similarity functions to eliminate these side effects. Based on a field measurement in a wind farm, we firstly show that MOST predicts a larger wind shear for the atmospheric stability parameter $\zeta>0.1$ and proposes new flow similarity functions without constraining $R_f$ to limit the overestimated wind shear by MOST. Next, different turbulence models based on MOST and a modified one based on the new similarity functions are investigated through numerical simulations. These turbulence models are combined with the actuator disk model (AD) and Reynolds-averaged Navier–Stokes equations (RANS) to model wind turbine wakes under stable conditions. As compared to measurements, numerical results show that turbulence models based on MOST result in larger wake deficits and slower wake recovery rate with a square root of the mean-squared-error (RSME) of wake deficit in the range of 0.07-0.18. This overestimated wake effect is improved by applying the new similarity functions and the RSME of wake deficit is averagely reduced by 0.05. Finally, we check the role of the under-predicted turbulence intensity playing in the larger wake deficit predicted by models based MOST. Additional numerical simulations using the modified turbulence model are carried out, in which the roughness length is reduced to impose a hub-height ambient turbulence intensity equivalent to the MOST case. Simulation results show that reducing turbulence intensity enhances wake effects, however, it cannot reproduce the large wake deficit predicted by models based on MOST, which suggests that the overestimated wake effect by MOST could be also related to the overestimated wind shear.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Accurate lithium battery diagnosis and prognosis is critical to increase penetration of electric vehicles and grid-tied storage systems. They are both complex due to the intricate, nonlinear, and path-dependent nature of battery degradation. Data-driven models are anticipated to play a significant role in the behavioral prediction of dynamical systems such as batteries. However, they are often limited by the amount of training data available. In this work, we generated the first big data comprehensive synthetic datasets to train diagnosis and prognosis algorithms. The proof-of-concept datasets are over three orders of magnitude larger than what is currently available in the literature. With benchmark datasets, results from different studies could be easily equated, and the performance of different algorithms can be compared, enhanced, and analyzed extensively. This will expend critical capabilities of current AI algorithms, tools, and techniques to predict scientific data.

Earthquake-triggered landslides represent a significant seismic-related disaster, posing threats to both the lives and properties of individuals in affected areas. Furthermore, they can result in road and river blockages, as well as other secondary disasters, significantly impacting post-earthquake rescue efforts. Efficient and accurate rapid assessment of high-risk landslide zones carries important implications for decision-making in disaster response and for mitigating potential secondary disasters. This study uses the high-intensity Zone VII to IX of the 5 September 2022 Luding Ms6.8 earthquake as a case study. The "difference method" and the "cumulative displacement method," based on the simple Newmark model, are employed to assess earthquake-triggered landslides. The evaluation results from both methods demonstrate that the areas posing an ex-tremely high risk of earthquake-triggered landslides are predominantly situated on the western side of the Xianshuihe Fault. Actual landslide data verification shows that both models have high predictive accuracy, with the difference method model slightly outper-forming the cumulative displacement method model. Moreover, the study recommends determining threshold values for each landslide hazard interval with significant physical meaning using past strong earthquake data as soon as possible when utilizing the difference method to assess the risk of earthquake-triggered landslides.

Catalyst with high catalytic activity and good stability are desirable in the electrocatalytic oxidation of glucose. Herein, Pt concave nanocubes with high-index facets (HIFs) supported by carbon black (Pt CNC/CB) are prepared through a hydrothermal method. The experimental results demonstrate that the peak current densities in different potential regions on the Pt CNC/CB anode are 0.22, 0.20, and 0.60 mA cm−2, respectively. The glucose oxidation reaction shows superior performances in basic and neutral conditions than in acid conditions. Better stability is achieved by Pt CNC/CB than Pt concave nanocubes (Pt CNCs). Abundant surface defects with low-coordinated atom numbers, such as the steps, kinks, and edges, are served as active sites in the electrocatalytic oxidation of glucose. With the addition of carbon black, the catalytic activity can be improved by facilitating the full exposure of the active surface defects on the HIFs of Pt CNCs. Moreover, to address the aggregation of Pt CNCs, caused by the high surface energy of HIFs, the introduction of carbon material is an effective way to preserve the HIFs, and thus enhance the stability of the catalyst. Hence, the prepared Pt CNC/CB electrocatalyst has great potential to be applied in the electrooxidation of glucose.

A simple approach to enable water-management agencies employing free data to achieve the goal of using a single set of predictive equations for water-quality retrievals with satisfactory accuracy is proposed. Multiple regression-derived equations based on surface reflectance, band ratios, and environmental factors as predictor variables for concentrations of Total Suspended Solids (TSS), Total Nitrogen (TN), and Total Phosphorus (TP) were derived using a hybrid forward-selection method that considers Variance Inflation Factor (VIF) in the forward-selection process. Landsat TM, ETM+, and OLI/TIRS images were jointly utilized with environmental factors, such as wind speed and water surface temperature, to derive the single set of equations. The coefficients of determination of the best-fitting resultant equations varied from 0.62 to 0.79. Among all chosen predictor variables, ratio of reflectance of visible red (Band 3 for Landsat TM and ETM+, or Band 4 for Landsat OLI/TIRS) to visible blue (Band 1 for Landsat TM and ETM+, or Band 2 for Landsat OLI/TIRS) has a strong influence on the predictive power for TSS retrieval. Environmental factors including wind speed, remote sensing-derived water surface temperature, solar altitude, and time difference (in days) between the image acquisition and water sampling were found important in water-quality parameter estimation.

Low back pain is a clinically highly relevant musculoskeletal burden and is associated with inflammatory as well as degenerative processes of the intervertebral disc. However, the pathophysiology and cellular pathways contributing to this devastating condition are still poorly understood. Based on previous evidence, we hypothesize that tissue renin-angiotensin system (tRAS) components, including the SARS-CoV-2 entry receptor angiotensin-converting enzyme 2 (ACE2), are present in human nucleus pulposus (NP) cells and associated with inflammatory and degenerative processes. Experiments were performed with NP cells from 4 human donors. The existence of angiotensin II, angiotensin II type 1 receptor (AGTR1), AGTR2, MAS-receptor (MasR), and ACE2 in human NP cells was validated with immunofluorescent staining and gene expression analysis. Hereafter the cell viability was assessed after adding agonists and antagonists of the target receptors as well as angiotensin II in different concentrations for up to 48 hours of exposure. A TNF-α-induced inflammatory in vitro model was employed to assess the impact of angiotensin II addition and the stimulation or inhibition of the tRAS receptors on inflammation, tissue remodeling, expression of tRAS markers, and the release of nitric oxide (NO) into the medium. Further, protein levels of IL-6, IL-8, IL-10, and intracellular as well as secreted angiotensin II were assessed after exposing the cells to the substances, and inducible nitric oxide synthase (iNOS) levels were evaluated utilizing Western Blot. The existence of tRAS receptors and angiotensin II were validated in human NP cells. Cell viability analysis revealed no cytotoxic effects of angiotensin II. The AGTR1 inhibitor Candesartan and the MAS receptors AVE0991 showed cytotoxic effects at high concentrations (100 µM). The addition of angiotensin II only showed a mild impact on gene expression markers. However, there was a significant increase in NO secreted by the cells. The gene expression ratios of pro-inflammatory/anti-inflammatory cytokines IL-6/IL--10, IL-8/IL-10, and TNF-α /IL-10 were positively correlated with the AGTR1/AGTR2 and AGTR1/MAS1 ratios, respectively. The stimulation of the AGTR2 MAS-receptor and the inhibition of the AGTR1 receptor revealed beneficial effects on the gene expression of inflammatory and tissue remodeling markers. This finding was also present at the protein level. We did not find alterations in iNOS protein concentrations after adding the drugs. The current data showed that tRAS components are expressed in human NP cells and are associated with inflammatory and degenerative processes. Further characterization of the associated pathways is warranted. The findings indicate that tRAS modulation might be a novel therapeutic approach to intervertebral disc disease.

Target pests of genetically engineered crops producing both defensive allelochemicals and Bacillus thuringiensis (Bt) toxins often sequentially or simultaneously uptake allelochemicals, Bt toxins, and/or insecticides. How the three types of toxins interact to kill pests remains underexplored. Here we investigated the interactions of Bt toxin Vip3A, plant allelochemical flavone, and insecticide emamectin benzoate in Spodoptera frugiperda. Simultaneous administration of flavone LC25 + Vip3A LC25, emamectin benzoate LC25 + Vip3A LC25, and flavone LC15 + emamectin benzoate LC15 + Vip3A LC15 but not flavone LC25 + emamectin LC25 yielded a mortality significantly higher than their expected additive mortality (EAM). One-day preexposure to one toxin at LC5 followed by 6-day exposure to the same toxin at LC5 plus another toxin at LC50 showed that the mortality of flavone LC5 + Vip3A LC50, emamectin benzoate LC5 + Vip3A LC50, and Vip3A LC5 + emamectin benzoate LC50, were significantly higher than their EAM, while that of flavone LC5 + emamectin benzoate LC50 was significantly lower than their EAM. No significant difference existed among the mortalities of Vip3A LC5 + flavone LC50, emamectin benzoate LC5 + flavone LC50, and their EAMs. The results suggest that the interactions of the three toxins are largely synergistic (inductive) or additive, depending on their combinations and doses.

As an essential synthetic material used in continuous casting of steels, mold fluxes improve the surface quality of steel slabs. In this study, a CaO-SiO₂-Na₂O based low-fluorine mold flux was solidified by an improved water-cooled copper probe with different temperatures of molten flux and different probe immersion times. The heat flux through solid films and the film structures were calculated and inspected, respectively. The results indicate: large internal cracks (formed in the glassy layer of films during solidification) were observed, the formation and evolution of those cracks contributed to the the unstable heat flux density. The roughness of the surface in contacted with the water-cooled copper probe formed as films were still glassy and the roughness have no causal relationship with crystallization or devitrification. Combeite with columnar and faceted dendritic shapes is the main crystal in the film.

To alleviate the contradiction between the increasing demand for water and the shortage of resources and to provide a favorable institutional environment for water rights trading, the Chinese government has strengthened the top-level design of water management system. However, the water-rich regions (southern regions of China) have good water resource endowment and a surplus of total water consumption indicators. Does this mean that there is no incentive and no need to conduct water rights trading in these regions? Through the investigation of water rights circulation cases in the Taihu Basin, a typical water-rich region of China, we established the existence of trading demand and some difficulties in conducting transactions. This paper argues that the needs of trading include alleviating the water gap in regional development, solving the water demand for large new projects, coordinating trans-jurisdiction water disputes. The plight of trading includes the lack of awareness, irregular process, excessive administrative intervention, and imperfect trading system.

Semen Allii Fistulosi is the seed of Allium fistulosum L. of the Liliaceae family. The purpose of this study was to extract, characterize, and evaluate the antioxidant activity in vitro of proteins from Semen Allii Fistulosi (PSAF). Using single factor and orthogonal design, the optimum conditions of extraction were determined to be as follows: extraction time 150 min, pH 8.5, temperature 60℃, and ratio (v/w, mL/g) of extraction solvent to raw material 35. The isoelectric point of the pH was determined to be about 4.4 and 10.2, by measuring the protein content of PSAF solutions at different pH. The amino acid composition of PSAF was determined by high performance liquid chromatography (HPLC), and the results suggested that the species of amino acids contained in the PSAF was complete. Sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS–PAGE) analysis showed the molecular weight was mainly between 40 and 55 kDa, and Fourier-transform infrared spectroscopy (FTIR) characterized prevalent protein absorption peaks. PSAF exhibited potent scavenging activities against DPPH assays, via targeting of hydroxyl and superoxide radicals, while chelating Fe2+ activity, and demonstrating weak reducing power. This work revealed that PSAF possessed potential antioxidant activity in vitro, suggesting potential for use of PSAF as a natural antioxidant.

Lirianthe delavayi has valuable ornamental and medicinal value, is an important economic tree, and has a long history of cultivation. As important regulatory molecules, miRNAs are involved in important physiological processes, such as the plant stress response, organ morphogenesis, hormone secretion, and signaling. In this study, based on miRNA sequencing analysis of wild and cultivated Lirianthe delavayi, we explored the differences in posttranscriptional regulation during the cultivation of Lirianthe delavayi from the aspect of miRNA molecular regulation. The results revealed the following: 1. A total of 365 miRNAs were sequenced and identified, and their first bases had obvious uracil (U) base preferences. Among them, 242 miRNAs were classified into 32 miRNA families; 2. Analysis of miRNA expression differences revealed that 39 miRNAs had significant expression differences between wild and cultivated populations; 3. Bioinformatics target gene prediction and target gene enrichment analysis of significantly differentially expressed miRNAs revealed that the target genes were significantly enriched in plant‒pathogen interactions, sphingolipid metabolism, defense responses, and ADP binding. 4. The plant‒pathogen interaction pathway involves seven differentially expressed miRNAs and 30 miRNA‒target gene regulatory pairs, which are involved mainly in pathogen signature molecule recognition and binding, signal transduction, and the regulation of disease resistance molecules or gene expression; Ath-MIR169g-p3_2ss7AG19GA, ath-MIR169g-p5_2ss7AG19GA, and ath-miR408-3p_L-3 are expressed only in wild population, and it is hypothesized that the domestication process from wild to cultivation species may be accompanied by the loss of disease resistance-related miRNAs. This study provides a reference for exploring the posttranscriptional-level regulatory mechanisms of adaptive changes in Lirianthe delavayi from wild to cultivated.