The present study analyzed light emitting diodes (LEDs) as an output load and used a Taylor series to describe the characteristic curve based on the exponential characteristic of voltage and current. A prototype circuit of a flyback LED driver system was established to verify whether the theory is consistent with actual results. This study focused on the exponential relationship of LED voltage and current. Conventional simulations usually used linear models to present LED loads. However, the linear model resulted in considerable error between simulation and actual characteristics. Therefore, this study employed a Taylor series to describe the nonlinear characteristic of an LED load. Through precise calculations with Mathcad computation software, the error was effectively reduced. Moreover, the process clarified the influence of temperature on LEDs, which benefited the characteristic analysis of the entire system. Finally, a realized circuit of 120-W flyback LED drivers was established for conducting theory verification, including theoretic analysis and evaluation of the system design process of the flyback converter. The circuit simulation software SIMPLIS was used to demonstrate the system model, which enabled quick understanding of the system framework established in this study. Regarding LEDs, a commercially available aluminum luminaire was used as the output load. The measured results of the actual circuit and the simulation results were remarkably consistent. For the same system at the same temperature, the error between the simulation and actual results was less than 3%, which proved the reliability of the Taylor series simulation.

Mechanical ventilation (MV), used in patients with acute lung injury (ALI), induces diaphragmatic myofiber atrophy and contractile inactivity, termed ventilator-induced diaphragm dysfunction. Phosphoinositide 3-kinase- (PI3K-) is crucial in modulating fibrogenesis during the reparative phase of ALI; however, the mechanisms regulating the interactions among MV, myofiber fibrosis, and PI3K- remain unclear. We hypothesized MV with or without bleomycin treatment would increase diaphragm muscle fibrosis through the PI3K- pathway. Five days after receiving a single bolus of 0.075 units bleomycin intratracheally, C57BL/6 mice were exposed to 6 or 10 mL/kg MV for 8 h after receiving 5 mg/kg of AS605240 intraperitoneally. In wild-type mice, bleomycin exposure followed by MV 10 mL/kg prompted significant increases in disruptions of diaphragmatic myofibrillar organization, transforming growth factor-1, oxidative loads, Masson’s trichrome staining, extracellular collagen levels, positive staining of -smooth muscle actin, PI3K- expression, and myonuclear apoptosis (P < 0.05). Decreased diaphragm contractility and peroxisome proliferator activated receptor- coactivator-1 levels were also observed (P < 0.05). MV-augmented bleomycin-induced diaphragm fibrosis and myonuclear apoptosis were attenuated in PI3K-γ-deficient mice and through AS605240-induced inhibition of PI3K- activity (P < 0.05). MV-augmented diaphragm fibrosis after bleomycin-induced ALI is partially mediated through PI3K-γ. Therapy targeting PI3K-γ may ameliorate MV-associated diaphragm fibrosis.

Gastric inflammation-related disorders are commonly observed digestive system illnesses char-acterized by the activation of proinflammatory cytokines, particularly tumor necrosis factor-α (TNF-α). This results in the induction of cyclooxygenase-2 (COX-2)/prostaglandin E2 (PEG2) and matrix metallopeptidase-9 (MMP-9). These factors contribute to the pathogenesis of gastric in-flammation disorders. We examined the preventive effects of Lonicera japonica Thunb. ethanol ex-tract (Lj-EtOH) on gastric inflammation induced by TNF-α in normal GES-1 cells. The GES-1 cell line was used to establish a model that simulated the overexpression of COX-2/PGE2 and MMP-9 proteins induced by TNF-α, to examine the anti-inflammatory properties of Lj extracts. The re-sults indicated that Lj-EtOH exhibits significant inhibitory effects on COX-2/PEG2 and MMP-9 ac-tivity, attenuates cell migration, and provides protection against TNF-α-induced gastric inflam-mation. The protective effects of Lj-EtOH are associated with the modulation of COX-2/PEG2 and MMP-9 through activation of TNFR–ERK 1/2 signaling pathways as well as the involvement of c-Fos and nuclear factor kappa B (NF-κB) signaling pathways. Based on our findings, Lj-EtOH ex-hibits a preventive effect on human gastric epithelial cells. Consequently, it may represent a novel treatment for the management of gastric inflammation.

The bridge crane is often used in a complex environment, often subject to interference of all loads. Some uncertainties factors often have an inevitable impact on its swing. So the force situation of the bridge crane during a working cycle is analyzed, and a three-dimensional dynamic mathematical model of the bridge crane is built. Through the simulation analysis of the model under the action of driving force and wind load, the change law of the swing angle of the bridge crane is studied. Then, the fuzzy control theory is used to determine the control parameter in the anti sway control process. The position, swing angle deviation and deviation rate of the bridge crane are taken as the input, and the parameter correction is obtained after the fuzzification by using the center of gravity method, the anti sway fuzzy control system of the bridge crane is designed and simulated. The research results show that the fuzzy PID anti sway controller can not only improve the adaptability of the control system, but also overcome the large overshoot, quickly restrain the swing, and effectively realize the anti sway function of the bridge crane.

The heavy metal lead (Pb) can irreversibly damage the human nervous system. To help understand Pb-induced damage, we applied a genetically encoded Förster resonance energy transfer (FRET)-based Pb biosensor Met-lead 1.44 M1 to two living systems to monitor the concentration of Pb: induced pluripotent stem cell (iPSC)-derived cardiomyocytes as a semi-tissue platform, and Drosophila melanogaster fruit flies as an in vivo animal model. Different FRET imaging modalities were used to obtain FRET signals, which represented the presence of Pb in the tested samples in different spatial dimensions. Using iPSC-derived cardiomyocytes, the relationship between beating activity (20–24 beats per minute, bpm) determined from the fluctuation of fluorescent signals and the concentrations of Pb represented by the FRET emission ratio values of Met-lead 1.44 M1 was revealed from simultaneous measurements. Pb (50 μM) affected the beating activity of cardiomyocytes, whereas two drugs that stop the entry of Pb differentially affected this beating activity: verapamil (2 μM) did not reverse the cessation of beating, whereas 2-APB (50 μM) partially restored this activity (16 bpm). The results clearly demonstrate a potential of this biosensor system as an anti-Pb drug screening application. In the Drosophila model, Pb was detected within the adult brain or larval central nervous system (Cha-gal4>UAS-Met-lead 1.44 M1) using fast epifluorescence and high-resolution two-photon 3D FRET ratio image systems. The tissue-specific expression of Pb biosensors provides an excellent opportunity to explore the possible Pb-specific populations within living organisms. We believe that this integrated Pb biosensor system can be applied to the prevention of Pb poisoning and advanced research on Pb neurotoxicology.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

Based on collected power generation data associated with solar irradiance, PV system conversion efficiency and cell temperature, an hourly solar PV power estimation model by a parallel artificial neural network (ANN) and particle swarm optimization (PSO) algorithm is proposed. Weight matrices related to different seasons and geographic areas for estimation power generations have been trained by real measured operation data. The parallel PSO algorithm with heuristic global optimization technique assists the ANN training process to get near optimal solutions precisely. The accuracy and reliability of estimation is audited by actual details of photovoltaic power stations in various regions and scales. The results of estimation model can not only assist the electricity dispatcher to explicitly monitor the trend of solar power generation in different areas, but also coordinate with traditional power plants to meet load demand more accurately. The presented model will bring benefits to power dispatching for larger scales of intermittent and unstable solar power generation.

Following our previous success in identifying new steroid-based anticancer agents, we herein disclosed the structural requirements for retaining high potency against cancer cells and associated modes of action. The structurally novel steroidal dimer by001 inhibited growth of different esophageal cancer cells and colony formation at low micromolar levels, elevated cellular ROS levels and caused mitochondrial dysfunction. Mechanistic studies showed that by001 induced cell death through the mitochondria and death receptor-mediated apoptotic pathways and autophagy induction, as well as inhibited migration.

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

In an IoT system, the sheer volume of data generated by numerous sensing devices necessitates a well-designed scheme for storing and retrieving data efficiently, enabling streamlined data processing and analytics. One promising storage architecture involves utilizing solid-state drives (SSDs) to cache data from hard disk drives (HDDs), thereby creating an SSD-based caching storage system. To further enhance access performance, it is possible to employ readahead techniques to minimize data access latency. However, the existing Linux readahead scheme falls short in fully leveraging SSD-based caching storage systems. We address this limitation by introducing a novel cross-layered readahead architecture that effectively communicates with the VFS layer, the file system layer, and the block I/O layer. This communication facilitates the acquisition of readahead timing, readahead data continuity, and readahead data location, respectively. To guide prefetching decisions, our architecture analyzes the degree of data access sequentiality, the performance model of the target storage device, and the access patterns of the I/O workload on the corresponding storage device. The implementation of this new architecture in the Linux kernel yields promising experimental results, demonstrating its robustness by consistently outperforming the stock Linux kernel. Notably, our architecture reduces the total execution time of the stock Linux kernel by up to 49%, except in cases of random workloads where both the stock Linux kernel and our architecture exhibit similar performance.

This paper reports the efforts made and experiences gained in developing the Flood Prevention and Emergency Response System (FPERS) powered by Google Earth Engine, with focus on its applications at the three stages of floods. At the post-flood stage, FPERS integrates various remote sensing imageries, including Formosat-2 optical imagery, to detect and monitor barrier lakes, synthetic aperture radar imagery to derive an inundation map, and high-spatial-resolution photographs taken by unmanned aerial vehicles to evaluate damage to river channels and structures. At the pre-flood stage, a huge amount of geospatial data are integrated in FPERS and are categorized as typhoon forecast and archive, disaster prevention and warning, disaster events and analysis, or basic data and layers. At the during-flood stage, three strategies are implemented to facilitate the access of the real-time data: presenting the key information, making a sound recommendation, and supporting the decision-making. The example of Typhoon Soudelor in August of 2015 is used to demonstrate how FPERS was employed to support the work of flood prevention and emergency response from 2013 to 2016. The capability of switching among different topographic models and the flexibility of managing and searching data through a geospatial database are also explained, and suggestions are made for future works.

Our study explores the role of cancer-derived extracellular exosomes (EXs), particularly focusing on collagen alpha-3 (VI; COL6A3), in facilitating tumor dissemination and metastasis in epithelial ovarian cancer (EOC). We found that COL6A3 is expressed in aggressive ES2 derivatives, SKOV3 overexpressing COL6A3 (SKOV3/COL6A3), and mesenchymal-type ovarian carcinoma stromal progenitor cells (MSC-OCSPCs), as well as their EXs, but not in less aggressive SKOV3 cells or ES2 cells with COL6A3 knockdown (ES2/shCOL6A3). High COL6A3 expression correlates with worse overall survival in EOC patients, as evidenced by TCGA and GEO data analysis. In vitro experiments showed that EXs from MSC-OCSPCs or SKOV3/COL6A3 cells significantly enhance invasion ability in ES2 or SKOV3/COL6A3 cells, respectively (both, P <0.001). In contrast, ES2 cells with ES2/shCOL6A3 EXs exhibit reduced invasion ability (p<0.001). In vivo, the average disseminated tumor numbers in the peritoneal cavity were significantly greater in mice receiving intraperitoneally injected SKOV3/COL6A3 cells than in SKOV3 cells (p<0.001). Furthermore, mice intravenously (IV) injected with SKOV3/COL6A3 cells and SKOV3/COL6A3-EXs showed increased lung colonization compared to mice injected with SKOV3 cells and PBS (p=0.007) or SKOV3/COL6A3 cells and PBS (p=0.039). Knockdown of COL6A3 or treatment with EXs inhibitor GW4869 or rapamycin-abolished COL6A3-EXs may suppress the aggressiveness in EOC.

Cadmium(Cd) is a highly toxic and cumulative environmental pollutant. Siderophores are heavy metal chelators with high tolerance to heavy metals such as Cd. Furthermore, ryegrass (Lolium perenne L.) has potential remediation capacity for soils contaminated by heavy metals. Consequently, using ryegrass alongside beneficial soil microorganisms that produce siderophores may be an effective means to remediate soils contaminated with Cd. In this study, Bacillus strains WL1210 and CD303 that were previously isolated from the rhizospheres of Nitraria tangutorum in Wulan and Peganum harmala L in Dachaidan, respectively, both arid sandy environments, were evaluated for heavy metal pollution mitigation. The results indicate that both strains of Bacillus exhibit favorable biological characteristics and stress resistance, and they are both producers of siderophores, which promote the growth of ryegrass under Cd stress.

The increased consumption of high fat-containing foods has been linked to the prevalence of obesity and abnormal metabolic syndromes. Rhizopus oligosporus, a fungus in the family Mucoraceae, is widely used as a starter for homemade tempeh. Although R. oligosporus can prevent the growth of other microorganisms, it grows well with lactic acid bacteria (LAB). Lactobacillus plantarum can produce β-glucosidase, which catalyzes the hydrolysis of glucoside isoflavones into aglycones (with greater bioavailability). Therefore, the development of a soybean-based functional food by the co-inoculation of R. oligosporus and L. plantarum is a promising approach to increase the bioactivity of tempeh. In this study, the ameliorative effect of L. plantarum in soy tempeh on abnormal carbohydrate metabolism in high-fat diet (HFD)-induced hyperglycemic rats was evaluated. The co-incubation of L. plantarum with R. oligosporus during soy tempeh fermentation reduced the homeostatic model assessment of insulin resistance, HbA1c, serum glucose, total cholesterol, triglyceride, free fatty acid, insulin, and low-density lipoprotein contents and significantly increased the high-density lipoprotein content in HFD rats. It also increased the LAB counts as well as the bile acid, cholesterol, triglyceride, and short-chain fatty acid contents in the feces of HFD rats. Our results suggested that the modulation of serum glucose and lipid levels by LAB occurs via alterations in the internal microbiota, leading to the inhibition of cholesterol synthesis and promotion of lipolysis. Tempeh, produced with both L. plantarum and R. oligosporus, may be a beneficial dietary supplement for individuals with abnormal carbohydrate metabolism.

In this paper, the overall performance of Cu-(In,Ga)-Se₂ (CIGSe) solar cells was improved in the ultraviolet (UV)–visible wavelength region by two-segment process. In which, adjusting DC sputtering powers (20–40 W) for absorbers (segment I), and metal-alloy compositions (CdS, ZnO/CdS, ZnMgO/CdS and ZnMgO) for buffers (segment II) were explored and characterized. Upon choosing the optimal-30-W CIGSe-absorber (with 0.95-CGI ratio) sputtered by the segment-I process, the Cu-rich film can distinctly boost grain growth, thus reducing the trap state density. After segment-II process as the toxic-CdS alternative, the optimal Zn_0.9Mg_0.1O-alloy buffer can reach the best conversion efficiency (η = 8.70%) was attained for the environmental protection. Meanwhile, and the overall internal/external quantum efficiencies (IQE/EQE) were improved by 13.15%, respectively for the 2.48–3.62-eV bandgap (short wavelength) range. The developed photovoltaic (PV) module (with 9 optimum-CIGSe cells) exhibits acceptable stability with a variance within ±5% over the 60-day experiment. This discovery in PV-device research contributes to a new scientific understanding of renewable energy. Furthermore, this study undeniably enhances the progress of practical applications for PV-modules in alignment with sustainable development goals. It also actively supports the development of eco-friendly communities.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

In this review, the following information describes the manifestation of sleep deprivation by human beings and its adverse effect on their health. Sleep deprivation has been demonstrated into namely two types known as REM sleep and NREM sleep affecting our health in so a problematic way that it is making our body immune to many diseases leading to lethal problems. Therefore, great research by many scientists has discovered that the turmeric “Curcuma longa” which is been used in every Indian kitchen since ancient times, has shown a remarkable effect on the problem caused by sleep deprivation but due to its poor solubility and low bioavailability drawn it into a great disadvantage. But the help of the study of nanotechnology and the evolution of curcumin into nano–curcumin made the possibility of the remarkable effect by making the curcumin more potent and enhancing its stability. Immunological changes due to sleep deprivation lead to Alzheimer’s disease, glioma, neuropathic pains, and many more. Therefore, this review has been summarized as it is been providing information related to curcumin and its affection for sleep deprivation.

This paper takes the VR animation display of the Ming Xiao Mausoleum General stone statue life as an example to study the advantages of VR animation in the display of material heritage. Combined with literature and pictures, the digital restoration of the Ming Xiao Mausoleum stone statue is carried out in MAYA and Z brush, and the construction of the scene and the output of the final effect are realized in UE4.

Various vaccines have been developed in response to the SARS-CoV-2 pandemic, and the safety of vaccines has become an important issue. COVID-19 vaccines-related central nervous system inflammatory demyelinating diseases (CNS IDDs) have been reported recently. We present one case of AstraZeneca vaccine-related myelin oligodendrocyte glycoprotein (MOG) antibody-associated disease and literature review another 78 patients published from January 2020 to October 2022. Patients were divided into three vaccine groups (viral vector, mRNA and inactivated vaccines) for further analyses. Among 79 patients with COVID-19 vaccines-related CNS IDDs, 49 (62%) cases received viral vector vaccines, 20 (25.3%) received mRNA vaccines and 10 (12.7%) received inactivated vaccines. Twenty-seven cases (34.2%) were confirmed with autoantibodies, including 15 patients (19%) with anti-MOG, 11 (13.9%) with anti-aquaporin 4 (AQP4), and one (1.3%) with both antibodies. Significantly, more males developed CNS IDDs post viral vector vaccines compared to mRNA and inactivated vaccines. Patients receiving mRNA vaccines were older than other groups. Furthermore, mRNA and inactivated vaccines correlated more with anti-AQP4 antibodies, while viral vector vaccines showed higher MOG positivity. The research suggests potential associations between COVID-19 vaccines-related CNS IDDs and gender, age, and autoantibodies, contingent on vaccine types. Protein sequence analysis implies similarities between the S protein and AQP4/MOG. Further studies may elucidate the mechanisms of CNS IDDs, aiding vaccine selection for specific groups.

Five new cembrane-type diterpenes, lobocalines A–E (1–5), and four new steroids, lobocalines F–I (9–12), along with six known related compounds (6–8 and 13–15) were isolated from the Yalong Bay soft coral Lobophytum catalai. The structures of the new compounds were elucidated by extensive spectroscopic analysis, NMR calculation with DP4+ analysis, time-dependent density functional theory-electronic circular dichroism (TDDFT-ECD) calculations, X-ray diffraction analyses, and the comparison with the reported spectroscopic data of known compounds. Further, with the aid of X-ray diffraction analysis, the structure of lobocrasol B (15) was firmly revised as 15a. In in vitro bioassays, compound 2 showed moderate antibacterial activities against fish pathogenic bacteria Streptococcus parauberis KSP28 and Phoyobacterium damselae FP2244 with minimum inhibitory concentration (MIC) values of 8.7 and 17.3 µg/mL, respectively. All the steroids exhibited antibacterial activities against the S. parauberis KSP28 with MIC values ranging from 12.3 to 53.6 µg/mL. Compounds 2, 7 and 14 have remarkable inhibitory effects on the hemolysin production of Staphylococcus aureus, while compounds 8–12 have medium inhibitory effects on the pyocyanin production in Pseudomonas aeruginosa.

Dysregulation of cartilage homeostasis and the changes in the density and the architecture of the subchondral bone were postulated as a potent mechanically pathological activity contributing to osteoarthritis (OA) pathogenesis. Extracorporeal shockwave therapy (ESWT) is a new, none invasive and effective method in the treatment of animal OA model. In the current study, we demonstrated that shockwave induced the expression of protein-disulfide isomerase-associated 3 (Pdia-3) which is a multifunctional protein hypothesized to be a significant mediator for 1α,25-Dihydroxyvitamin D3 (1α,25(OH)₂D₃) signaling pathway using two-dimensional electrophoresis. Histological analysis and quantitative polymerase chain reaction (qPCR) were verified and observed that the expression of Pdia-3 at 2 weeks was significantly higher than that of any other group at 4 weeks, 8 weeks, and 12 weeks post-shockwave treatment in early OA knee of rat. The other factors of the 1α,25(OH)₂D₃ rapid membrane signaling pathway including extracellular signal-regulated protein kinases 1 (ERK1), osteopontin (OPG), alkaline phosphatase (ALP), and matrix metallopeptidase 13 (MMP13) were measured and significantly increased by qPCR at 2 weeks post-shockwave treatment in early OA knee. Our proteomic data revealed significant Pdia-3 expression in microenvironments of joint tissue that could be actively responded to ESWT, which may potentially regulate biological function of chondrocytes and osteoblasts in the treatment of OA knee.

Agriculture is an industry that heavily relies on the environment. The increasing frequency of ex-treme disasters attributable to climate change has adversely affected agricultural land and dis-rupted the stability of the supply of agricultural products. Therefore, we implemented a research program focused on current strategies for adapting to agricultural meteorological disasters. The primary goal was to actively promote disaster prevention information and techniques through information platforms and applications and to provide refined forecasting and an early warning system to enhance preparedness for and recovery from agricultural disasters. This initiative can transform passive mitigation into dynamic action by disseminating crucial information to farmers. We integrated meteorological data and crop characteristics to develop disaster prevention strate-gies for the predisaster, during-disaster, and postdisaster stages to empower farmers to implement autonomous disaster prevention, ensuring their profitability and minimizing the impact of disas-ters. This paper presents an agricultural disaster prevention system involving cross-disciplinary collaboration to establish an early warning system for crop disasters. However, the effectiveness of the early warning system relies on the availability of complete meteorological and crop infor-mation, necessitating high-density agricultural meteorological stations, refined weather forecast services, historical crop damage data, and ongoing research and development on disaster preven-tion technology. In the system, a diversified social media interface is used to provide local farmers with weather forecast information. When impending disasters are identified, the platform acti-vates disaster prevention measures to reduce agricultural losses. This article paper introduces Taiwan’s agricultural disaster prevention system as a complete disaster prevention strategy.

Background: Cancer patients require cross-professional care during the diagnosis and treatment periods. Therefore, methods for effectively carrying out case management are essential to tumor care. Purpose: To investigate the effects of using the community software LINE Official Ac-count on oral cancer case management. Methods: An experimental design was used; 100 patients were randomly divided into two groups by using a computer-generated random number table. The experimental group used LINE Official Account, which gave them self-care information, timely messages, and one-on-one health-care consultations. The control group followed standard healthcare practices. Results: The experimental group was satisfied with the self-care information provided by LINE Official Account (86.9%), patients regularly checked the self-care information (89.4%) and would check the information when receiving a push notification (54.3%). Ten patients used the one-on-one consultation(20.0%). LINE Official Account had a significant effect on the rate of participation in support groups. Generalized estimating equations indicated a significant difference between the two groups regarding the overall quality of life over 7 days (P = 0.023). Conclusion: Community software applications used in oncological case management can improve self-management and empower, also enable tracking of long-term follow-up effectiveness and reinforce the case manager’s role as a family therapist. Therefore, this study recommends that case manager systems be incorporated into mobile applications to increase the sustainable management, accessibility, effectiveness, and satisfaction of oncological management systems. This study also provides the value of Sustainable Development Goals (SDGs) with Good Health and Well-being, and decreased social withdrawal among patients with oral cancer.

A plant’s early response to pathogen stress is a vital indicator of its disease resistance. In order to study the response mechanism of resistant and susceptible flax cultivars to Fusarium oxysporum f. sp. lini (Foln), we applied RNA-sequencing to analyze transcriptomes of flax with Foln 0.5, 2 and 8 hours post inoculation (hpi). We found a significant difference in the number of differential expression genes (DEGs) between resistant and susceptible flax clutivars. The number of DEGs in the Fusarium-resistant cultivar increased dramatically at 2 hpi, and a large number of DEGs participated in the Fusarium-susceptible cultivar response to Foln infection 0.5 hpi. GO enrichment analysis determined that the up-regulated DEGs of both flax cultivars were enriched such as oxidoreductase activity and oxidation-reduction process. At the same time, the genes involved in diterpenoid synthesis were up-regulated in resistant cultivar, while those involved in extracellular region, cell wall and organophosphate ester transport were down-regulated in susceptible cultivar. KEGG enrichment analysis showed the genes encoded WRKY 22 and WRKY33 which involved in MAPK signaling pathway were up-regulated expressed in S-29 and down-regulated expressed in R-7, negatively regulated the disease resistance of flax; The genes encoded Hsp 90 family which in involved in plant pathogen interaction pathway were up-regulated in R-7 and down-regulated in S-29, which positively regulated the disease resistance of flax; The genes encoded MYC2 transcription factor and TIFY proteins which involved in plant hormone signaling pathway were up-regulated in R-7, and regulated the jasmonic acid metabolism of flax and the signal transduction of plant hormones. Meanwhile seven regulatory genes with the most correlation were screened out, Among Lus10025000.g and Lus10026447.g regulated other genes expressed both in plant hormone signal transduction pathway and MAPK signal pathway. In conclusion, these findings will facilitate further studies on the function of these candidate genes in flax of response to Fusarium stress, and the breeding of disease-resistant flax cultivar.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

This paper revisits the analytical theory of fractional vibrations with the highlights in five aspects. First, we address the cases of structures with frequency dependent mass or damping or stiffness in Sections 2-4. Second, we introduce the theory based on the general second-order vibration motion equation with frequency dependent elements (mass, damping, stiffness) in Sections 5-7. Third, we present the analytical theory of seven specific classes of second-order vibration systems with frequency dependent mass or damping or stiffness in Sections 8 and 9. Fourth, we bring forward the analytical theory of seven classes of fractional vibration systems in Sections 10-12. Finally, as an application, we give the closed form expression of the forced response to multi-fractional Euler-Bernoulli beam in Section 13. The explanation of the nonlinearity of fractional vibrations is given in Section 14.

A case-crossover study examined how PM_2.5 from Asian Dust Storms (ADS) affects the number of emergency room (ER) admissions for cardiovascular diseases (CVDs) and respiratory diseases (RDs). Our data indicated that PM_2.5 concentration from ADS was highly correlated with ER visits for CVDs and RDs. The odds ratios (OR) increased by 2.92 (95% CI: 1.22-5.08) and 1.86 (95% CI: 1.30-2.91) per increase 10 µg/m³ in PM_2.5 levels, for CVDs and RDs, respectively. A 10 µg/m³ increase in PM_2.5 from ADSs was significantly associated with increase in ER visits for CVDs among those 65 years of age and older (an increase of 2.77 in OR) and for females (an increase of 3.09 in OR). In contrast, PM_2.5 levels had a significant impact on RD ER visits among those under 65 years of age (OR=1.77). The risk of ER visits for CVDs increased on the day when the ADS occurred in Taiwan and the day after (lag 0 and lag 1); the corresponding risk increase for RDs only increased on the fifth day after the ADS (lag 5). In Taiwan’s late winter and spring, the severity of ER visits for CVDs and RDs increases. Environmental protection agencies should employ an early warning system for ADS to reduce high-risk groups’ exposure to PM_2.5.

When existing at emulsion interface and continuous phase, dispersibility of water-soluble flexible polymer chains has obvious effect on rheology and dielectric properties of whole emulsion. CNF Pickering emulsion is a good system to research these properties with respect to their microscopic phase structure, dielectric and rheological properties by using cellulose nanofibers (CNF) as water-soluble Pickering emulsifier, liquid Paraffin as oil phase and DDAB as a cationic auxiliary surfactant. The CNF- and DDAB-contents were systematically varied while the water to paraffin oil ratio remained constant to discern the influence of the Pickering emulsifiers. Polarized optical microscopic images revealed that the droplets have tendency to become smaller size for higher CNF content, but bigger size for higher DDAB content, which was proved by the fluorescent analysis for CNF dispersibility with varying DDAB content. The dielectric damping exhibits a minimum, whose value decreases with increasing DDAB- and CNF-content. Increasing the DDAB-content promotes solubilization of CNFs in the aqueous phase and will increase the overall viscosity and yield points. Similarly, a higher CNF-content leads to a higher viscosity and yield point, but at high DDAB-contents the viscosity function exhibits an S-shape at intermediate CNF-content. To evaluate the results further they were compared with CNF-dispersions (without oil-phase), which showed a surfactant effect slightly on maximum stress but strongly on yield stress τy, indicating DDAB can promote the formation of CNF network rather than the viscosity of whole system.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

Antibiotics are in excessive use that has extensively increased antimicrobial resistance worldwide which has become the major public concern among the countries. To control this threat proper monitoring of the antimicrobial usage along with the increasing rate of antimicrobial resistance (AMR) is required. Further, surveillance of both the parameters is highly recommended for comparing the differences in distinct countries. Moreover, alternatives for antibiotics are also surveyed and are being researched for quick use in the near future. AMR is an issue that needs immense attention from various sectors. Thus, intervention of multisector is highly encouraged for better outcomes. One Health is one of the approaches that play a vital role in resolving this issue. In this research paper, six different European countries are discussed in terms of antimicrobial usage and AMR in the human and livestock sectors with the help of literature study and various reports published by different organizations. Data study has been conducted to collect the data for comparison study. Data sources of AMR and antimicrobial usage are analyzed and a thorough comparison of both antimicrobial use and AMR are conducted. Also, the application of One Health is studied for a balanced system. This article provides about various surveillance systems that are formed only to keep a track on the upcoming situation of AMR and the consumption of antimicrobials by the humans as well as animals. The article does not provide about all the details required to monitor the AMR issue but firmly allow the readers to get acknowledged with the broad information about the antimicrobial resistance across the six countries of Europe. The regular data collected by the different organizations play a vital role in monitoring the status of AMR and antimicrobial usage by humans and in live stocks. These annual reports have highly helped the government to decide for alternatives and have focused in many training activities to combat the AMR situation globally. AMR prevention is linked to the One Health concept. As antibiotic resistance genes persist on an interface between environment and animal and animal health, an approach is required in all three areas that stress the concept of 'One Approach to Health.'

Antimicrobial resistance (AMR) is an increasing hazard to human and animal health that necessitates an international response. Surveillance methods in high-income nations aided in the development of measures to combat AMR in animals. Demand for meat is increasing in countries making it critical to implement anti-AMR initiatives. Surveillance of AMR, on the other hand, is at best in its infancy, and the current evidence base for informing policymakers is geographically disparate. All of the isolates had high rates of AMR to medicines that are critical/highly important in human and animal medicine. A higher incidence of AMR was found in poultry farms. Our findings show that AMR, including MDR, is common in coli, Salmonella spp., commonly found in poultry. The study promotes the development of national policies, programs, and additional research based on a "One Health" approach that helps humans and animals, as well as the environment.

Exploring new approaches to innovating higher vocational education is a worldwide pursuit driven by the increasing demand for graduates equipped with competencies. This study investigated how Outcomes-Based Education (OBE) influences the attainment of graduate competence (AGC) in China’s higher vocational education, using the theory of Constructive Alignment (CA) as its foundation. The OBE framework incorporates intended learning outcomes (ILOs), project-based learning (PjBL), assessment strategies (ASs), and AGC. The study tested the model by assessing the impact of ILOs, PjBL, and ASs on AGC, respectively and sequentially. Surveys were administered to 320 CBEC learners in April 2024, resulting in 301 usable responses. Data were analyzed using structural equation modeling (SEM) with SPSS 23.0 and AMOS 24.0. Results indicated that PjBL and ASs were directly and positively related to graduate competency attainment, while ILOs were indirectly associated with graduate competence through the mediating roles of PjBL and ASs. The most substantial mediating effect between ILOs and graduate competence was ASs, followed by PjBL, and then, the chain mediating effect of PjBL and ASs. These findings enhance the theoretical understanding of OBE and provide detailed procedures for tracking and enhancing sustainability in higher vocational education. Beneficiaries include educators, policymakers, and accreditation bodies.

Entrepreneurship has been viewed as an opportunity for economic development and changing economic scenarios in global markets. Women are viewed as a reservoir of entrepreneurial talent, so they can be growth engines in novel markets. Previous studies have considered entrepreneurship as the most effective way towards the economic empowerment of women. Female students engaged in entrepreneurial education have been addressed persistently, while what transforms them in an education process is still unclear. Considering the transforming global economy and its influence on higher education, this study aims to detect female students transforming entrepreneurial competency, mindset, and intention into sustainable entrepreneurship. Using a self-compiled survey, we targeted 752 female students to investigate their entrepreneurial competency, mindset, and intention. SPSS and AMOS were used to transform the data for interpretation. We assumed that the impact of female students’ entrepreneurial competency could be modified by an entrepreneurial mindset and result in entrepreneurial intention. To detect this causal relationship, this study employed reliability, factor, structural equation modeling (SEM), and bootstrap-ping analyses to verify the evidence. The result of the SEM confirms that female students’ entrepreneurial competency will, through their entrepreneurial mindset, impact entrepreneurial intention. With bootstrapping, 5000 samples were collected, and it was demonstrated that the measure constructs were still reliable in the model. This study found that there is a mediation effect between entrepreneurial competency and entrepreneurial intention. The entrepreneurial mindset plays a crucial role in the transformation process. Without an entrepreneurial mindset, entrepreneurial competency cannot exert a significant effect on entrepreneurial intention. The findings can help reinvent related entrepreneurial education in higher education.

This paper uses the complex regression analysis method to establish the customer’s load regression models, which consider economic indicators, temperature and rainfall. Furthermore, the proposed models are used to study the forecasting feasibility of the future energy sales and summer peak load demand. At first, this paper used least-squares techniques to derive regression models for considering economic indicators and temperature of 34 customer energy sales and total energy sales. Besides, the AMI high voltage customer demand data and system generating capacity for 24 hours were adopted to forecast summer peak load. The above-mentioned data analysis tool is used by EViews software to achieve, in order to verify the feasibility of the research framework. The study found that although its forecasting model accuracy is low only when mixed with temperature and high voltage demands. So, when mixed with high voltage demand data and system generating capacity for 24 hours to forecast peak load, the average error is ± 0.87% and in the majority of its energy sales forecasting model of average error is ±3%. This result can provide power company as future reference.

Building information modeling (BIM) is the digital representation of physical and functional characteristics (such as geometry, spatial relationship, and geographic information) of a facility to support decisions during its life cycle. BIM has been extended beyond 3D geometrical representations in recent years, and now includes time as a fourth dimension and cost as a fifth dimension, as well as such other applications as virtual reality and augmented reality. The Internet of Things (IoT) has been increasingly applied in various products (smart homes, wearables) to enhance work productivity, living comfort, and entertainment. However, research addressing the integration of these two technologies (BIM and IoT) is still very limited, and has focused exclusively on the automatic transmission of sensor information to BIM models. This paper describes an attempt to represent and visualize sensor data in BIM with multiple perspectives in order to support complex decisions requiring interdisciplinary information. The study uses a university campus as an example and includes several scenarios, such as an auditorium with a dispersed audience and energy saving options for rooms with different functions (mechanical/electric equipment, classrooms, and laboratory). This paper also discusses the design of a common platform allowing communication among sensors with different protocols (Arduino, Raspberry Pi), the use of Dynamo to accept sensor data as input and automatically redraw visualized information in BIM, and how visualization may help in making energy-saving management decisions.

Two-dimensional (2D) of transition metal dichalcogenides (TMDCs) are potential candidates for thermoelectric (TE) applications due to their unique structural properties. In this paper, we constructed an 2D monolayer TMDCs semiconductor γ-PbSn2(X=S, Se, Te) and first-principles calculations and Boltzmann transport theory are used to study the thermoelectric performance. We found that γ-PbSnX2 had an ultra-high carrier mobility up to 4.04×103 cm2V−1s−1 leading to a metal-like electrical conductivity. Meanwhile, γ-PbSnX2 both have high Seebeck coefficients, resulting in high power-factors, and also shows intrinsic low lattice thermal conductivity of 6-8 W/mK at room temperature. The lower lattice thermal conductivity and high power-factors resulted in excellent thermoelectric performance. The high ZT values of γ-PbSnS2 and γ-PbSnSe2 were as high as 2.65 and 2.96 at 900 K, respectively. The result suggests that the monolayer γ-PbSnX2 are better candidates for excellent thermoelectric performance.

Accurately predicting the power of solar power generation can greatly reduce the impact of the randomness and volatility of power generation on the stability of the power grid system, which is beneficial for the balanced operation and optimized dispatch of the power grid system, and reduces operating costs. Solar PV power generation depends on weather conditions, which are prone to large fluctuations under different weather conditions. Its power generation is characterized by randomness, volatility and intermittency. Recently, the demand for further investigation and effective use on the uncertainty of short-term solar PV power generation prediction has been getting increasing attention in many application of renewable energy sources. In order to improve the predictive accuracy of output power of solar PV power generation and develop a precise predictive model, the authors worked predictive algorithms for the output power of a solar PV power generation system. Moreover, since short-term solar PV power forecasting is one of the important aspects for optimizing the operation and control of renewable energy systems and electricity markets, this review focuses on the predictive models of solar PV power generation, which can be verified in the daily planning and operation of a smart grid system. In addition, the predictive methods in the reviewed literature are classified according to the input data source used for accurate predictive models, and the case studies and examples proposed are analyzed in detail. The contributions, advantages and disadvantages of the predictive probabilistic methods are compared. Finally, the future studies of short-term solar PV power forecasting is proposed.

Globally increasing antibiotic resistance has been connected to the use of antibiotics in medical, veterinary, and agricultural medicine, contributing to the burden of antibiotic resistance in Asia and Europe. The main objective of this study was to correlations of antimicrobial-resistant of various pathogens in three compartments: humans, animals and the environment in India and Germany. A systematic search was carried out in Medline via PubMed, Google Scholar, and science direct, including studies published in 2022. Out of 532 papers, 24 were considered for meta-analysis. This study reveals that in India, β-lactam is highly resistant in animals. Quinolone, on the other hand, was highly resistant in humans. Furthermore, in the environment and integrated studies, aminoglycosides and β-lactams is resistant. While in Germany, a high rate of AMR resistance in all three sectors was reported in β-lactam. However, E. coli was the most frequent pathogen in both countries and is highly resistant to β-lactam, followed by cephalosporin in all the compartments. Monitoring and evaluating antibiotic-sensitivity patterns and developing proper antibiotic regimens may lead to improved outcomes for inhibiting and controlling E. coli infections in various parts of the world.

Longitudinal image registration of pulmonary computed tomography (PCT) images may serve as an essential tool for investigating the relationship between radiation dose distribution and the occurrence and phenotype of radiation-induced lung disease (RILD). Although numerous longitudinal registration algorithms have been developed for PCT, most similarity-based approaches are not suitable for PCT involving RILD due to the complex tissue variation between two PCT images. Moreover, conventional feature-based approaches might fail to find a sufficient number of matched pairs of feature points due to the disparate lung deformation caused by breathing and RILD. To overcome the challenges resulting from RILD, component structure coherence point drift (CSCPD) was proposed to establish a deformation model by decomposing the chest into several components and matching them with individual parameters based on coherence point drift (CPD). Moreover, a regional vascular point matching (RVPM) algorithm was proposed to generate a vascular subtree and to substantially increase the number of corresponding pairs between two images. Eventually, the components were recomposed and aligned by a thin plate spline algorithm. A performance assessment on 15 pairs of PCT images of patients with RILD yielded recall and precision values of 0.85 and 0.89 for RVPM, respectively. Moreover, the target registration error of CSCPD with RVPM (2.3 ± 1.79) was significantly better than that of conventional CPD with RVPM (2.95 ± 1.89) and conventional CPD (5.04 ± 2.87). Therefore, the proposed registration system is robust enough to address the disparate deformation of lungs with RILD, and it improves registration accuracy within the parenchyma.

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

The Wave Mode (WM) is a unique imaging mode of spaceborne synthetic aperture radar (SAR), which is dedicatedly designed for global ocean surface wave observations. Since it was firstly achieved in the ERS-1/SAR satellite starting from 1991, the WM data over global oceans have been continuously acquired by the ESA’s SAR instruments onboard the satellites of ERS-2 (1997 – 2011), ENVISAT (2002 – 2012), Sentinel-1A(2014--)/1B(2016--) and the Chinese GaoFen-3 SAR (2016--), for nearly 30 years. Therefore, spaceborne SAR WM data have been a ‘big data’, which however, has not been widely exploited for global ocean wave measurements. In this study, we demonstrate its application on global ocean wave measurements based on the ten-year Advanced SAR (ASAR) WM data.

This dataset consists of integral sea state parameters of significant wave height (SWH) and mean wave period (zero-upcrossing mean wave period, MWP) data derived from the advanced synthetic aperture radar (ASAR) onboard the ENVISAT satellite over its full life cycle (2002-2012) covering the global ocean. Both parameters are calibrated and validated against buoy data. A cross-validation between the ASAR SWH and radar altimeter (RA) data is also performed to ensure that the SAR-derived wave height data are of the same quality as the RA data. These data are stored in the standard NetCDF format, which are produced for each ASAR wave mode Level1B data provided by the European Space Agency. This is the first time that a full sea state product in terms of both the SWH and MWP has been derived from spaceborne SAR data over the global ocean for a decadal temporal scale.

Taking an existing public building as an example, on the basis of the measured data, the mathematical model of each equipment module of the chilled station and the TRNSYS custom module are established. The mathematical model of “chilled station cooling capacity—equipment power” is proposed and established. The full-frequency control strategy based on device contribution rate is proposed and established to set up the Matlab control module of the chilled station. The TRNSYS simulation platform is used to simulate a public building chilled station in cooling season. The result shows that the season energy efficiency rate of the public building air-conditioning system is 2.15 times the original after applying the new control strategy.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Background: Kawasaki disease (KD) is a form of vasculitis that primarily affects children under the age of 5 years old. Patients may be missed diagnosis when initial clinical symptoms do not fulfill the traditional criteria. We aimed to analyze factors that clinicians could use to differentiate febrile children suspected of KD. Method: We retrospectively enrolled a total of 83 febrile children who were initially suspected of KD, but they did not meet the American Heart Association (AHA) criteria for a diagnosis. However, some of these patients were diagnosed with KD during their second visit. We analyzed patients' characteristics, clinical symptoms, and laboratory data. Results: In total, 50 patients were enrolled in the study. Of those, ten patients were diagnosed with KD on their second visit (group 1), while the other 40 patients still did not fit a KD diagnosis (group 2). A patient with a neutrophil to lymphocyte ratio greater than 1.33 combined with a C-reactive protein more than 33 mg/L was more likely to have KD. Conclusion: Among patients suspected of KD that did not initially meet the criteria, clinicians should pay special attention to elevated neutrophil-to-lymphocyte ratios and CRP levels and closely follow up such patients.

With the ongoing COVID pandemic, the emergence of a novel omicron variant in November 2021 has chaos the world. Despite mass vaccination, this omicron has spread rapidly raising concerns around the globe. The Omicron variant has a vast array of mutations as compared to another variant of concern with overall 50 mutations where 30 mutations are present in its spike protein. This mutation has led to immune escape and more transmissibility compared to other variants, including Delta. A cluster of mutations (H655Y, N679K, and P681H) present at the omicron spike protein could aid in transmission. Currently, no virus-specific data are available to predict the efficacy of anti-viral and mAbs drugs. However, two monoclonal antibody drugs: Sotrovimab and Evusheld are authorized for emergency use in COVID patients. This virus is not fading away soon. The easiest solution and less expensive measure to fight against this pandemic are following COVID appropriate protocols.There is need to strengthen the level of research for development of potential vaccines and anti-viral drugs. It is also important to monitor and expand genomic surveillance to keep track of the emergence of new variants thus avoiding the spread of new diseases worldwide. This article highlights the emergence of omicron and vast number of mutation in its protein. In addition, recent advancement in drugs approved by FDA to treat COVID patients has been listed and focused in this paper.

The outbreak of COVID-19 in 2020 caused significant disruptions to global shipping and the world economy. This paper aims to investigate the impact of the pandemic on global shipping by analyzing the Baltic Dry Index (BDI). The BDI is a metric that reflects the worldwide shipping costs and directs related to supply and demand conditions, making it an indicator of economic production. The study utilizes data from 2019 to 2021, before and after the outbreak of COVID-19, and considers 13 independent variables, including raw materials, energy, stock market indexes, global port calls, and confirmed COVID-19 cases to investigate how to influent the BDI. The study employs stepwise regression to select variables and build models before and after the pandemic. The findings reveal that the key factors affecting the freight index BDI before the outbreak are: international scrap steel prices, iron ore prices, and the Commodity Research Bureau Index. However, after the COVID-19 outbreak, the factors affecting the BDI changed to the Shanghai Index, global port calls, and the number of confirmed COVID-19 cases.

Leishmaniasis is considered one of the different neglected tropical diseases by the World Health Organization. Over the past few decades to tackle leishmaniasis, effective and novel drugs have progressed. But few are expensive some other medication shows poor effects and few drugs with long treatment lead to cause resistance. But it is very important to start a better medication against leishmania so researchers came to the front of the utilization of natural products which are considered a better option. Finding active compounds in medicinal plants is another alternative to currently accessible medications. Materials and methods: This study examined and reported the far more potential natural products used to treat disease caused by Leishmania spp. Leishmaniasis, plant metabolites, in vivo, in vitro, and treatment against leishmaniasis have been used as search terms in the Google Scholar, PubMed, and Science Direct databases, and only papers published between 2015 and 2021 have been chosen for further analysis. Results: The use of novel natural compounds with leishmanicidal action as well as the leishmanicidal activity of natural compounds against promastigote, axenic, and intracellular amastigote forms were included in roughly 20 research papers that were reviewed.Conclusion: Due to their capacity to selectively target parasites without harming host cell viability, herbal plants are a possible source of new anti-leishmanial medication. Future leishmaniasis treatments will draw on the isolated compounds as a source, completing those already offered in clinics.

This paper gives both a general canonical quantum gravity theory and the general canonical quantum gravity theories of the Universe and general black hole, and discovers the relations reflecting symmetric properties of the standard nonlinear gravitational Lagrangian, which are not relevant to any concrete metric models. This paper concretely shows the general commutation relations of the general gravitational field operators and their zeroth, first, second and third style, respectively, of high order canonical momentum operators for the general nonlinear system of the standard gravitational Lagrangian, and then has finished all the four styles of the canonical quantization of the standard gravity.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Background: In long-term care facilities, there are many residents who do not have the ability to seek shelter by themselves in the case of an emergency. Thus, it is extremely important that the staff of nursing homes are equipped with correct disaster prevention concepts, emergency survival responses, and hazard mitigation measures. Purpose: Discuss the intervention effectiveness of different fire prevention and emergency response trainings at nursing homes and the relationship and predictivity of awareness to self-efficacy. Method: Recruit staff from two nursing homes through purposive sampling, using a two-team pre-and post-test design to collect results from 41 individuals in the experiment group and 40 individuals in the control group. The research tool is the “Nursing Home Fire Prevention and Emergency Response Awareness and Self-Efficacy Scale,” to compare the effectiveness of advanced and general fire safety trainings. Result: After receiving improved advanced fire safety training, the total score and the result of the experiment group on fire prevention and emergency response awareness and self-efficacy had both performed better than the control group who received general fire safety training (p < .001); fire prevention and emergency response awareness has significant and positive correlation with self-efficacy (r=.601, p < .001), and awareness is a significant predictor variable to self-efficacy (p < .001). Conclusion/Practical Application: This study finds that the key to improving learning effectiveness includes adding fire science concept chapter when creating fire safety training material in order to strengthen basic awareness; fire safety training should comprehensively introduce all related duty responsibilities of staff fire defense formation, in turn enabling mutual responsive support for the needs of the site; also, to become familiarized with the knowledge requires appropriate frequency of training and enhancing the staff’s awareness to fire prevention and emergency response, which is the most important key of learning effectiveness.

Hydrogels, soft materials with 3D polymer networks in aqueous solution, have been developed for engineering and bio-related fields. However, these conventional hydrogels are weak and brittle due to lack of energy dissipation mechanisms. Recently, dual-network hydrogels have been proposed, combining rigid and flexible networks and exhibiting high strength, stretchability, and toughness. This paper explores the rheological properties of dual-network hydrogels based on acrylamide and sodium alginate under large deformations. This dual network is a combination of a covalently crosslinked polyacrylamide network and a supramolecular crosslinked sodium alginate network at the presence of divalent calcium cations. Small and large amplitude oscillatory shear methods with Fourier transform rheology, stress decomposition method, and Chebyshev polynomial analysis of large amplitude oscillatory shear (LAOS) data were employed to evaluate non-linearity limit, toughness, and network rigidity. The concentration of calcium ions affects (concentrations 0-80 mg/ml) the nonlinear transition and limit points, and all gel samples exhibit strain hardening, shear thickening, and shear densification.

Multi-wire saw machining (MWSM) used for slicing hard-brittle materials in semiconductor, is an important material removal process that uses free abrasives. Cutting model of single-wire saw machining (SWSM) is the basis of MWSM, and the material removal mechanism of SWSM can better understand than MWSM. Mathematical model (includes brittle fracture and plastic deformation) is presented in this paper for SWSM ceramic with abrasives. This paper determines the effect of various machining parameters on the removal of hard-brittle materials. For brittle fracture of SWSM ceramics, the minimum of the strain energy density is used as a fracture criterion. The material removed of SWSM ceramics due to plastic deformation is calculated using the equations of motion. Actual wire-sawing experiments are conducted to verify the results from the developed mathematical model. Theoretical results agree with experimental data and practical experience. The developed mathematical model shows that brittle fracture plays a major concern role in material removed of SWSM ceramics. Wire speed and working load have positively correlated with material removed of SWSM ceramics. The coefficient of friction is low, a lateral crack, which propagates almost parallel to the working surface, leads to more brittle fracture and material removed is increased on SWSM ceramics.

We used the Bootstrap ARDL method to test the relationship between the export trades, FDI and CO₂ emissions of the BRICS countries. We found that China's foreign direct investment and the lag one period of CO₂ emissions have a cointegration on exports. South Africa's foreign direct investment and CO₂ emissions have a cointegration relationship with the lag one period of exports, and South Africa's the lag one period of exports and foreign direct investment have a cointegration relationship with the lag one period of CO₂ emissions. But whether it is China or South Africa, these three variables have no causal relationship in the long-term. Among the variables of other BRICS countries, Russia is the only country showed degenerate case #1 in McNown et al. mentioned in their paper. When we examined short-term causality, we found that CO₂ emissions and export trade showed a reverse causal relationship, while FDI and carbon emissions were not so obvious. Export trade has a positive causal relationship with FDI. Those variables are different from different situations and different countries.

Most methods for measuring environmental lead (Pb) content are time consuming, expensive, hazardous, and restricted to specific analytical systems. To provide a facile, safe tool to detect Pb, we created pMet-lead, a portable fluorescence resonance energy transfer (FRET)-based Pb biosensor. pMet-lead comprises a 3D-printed frame housing a 405-nm laser diode — an excitation source for fluorescence emission images (YFP and CFP) — accompanied by optical filters, a customized sample holder with a Met-lead 1.44 M1 (the most recent version)-embedded biochip, and an optical lens aligned for smartphone compatibility. Measuring the emission ratios (Y/C) of the FRET component enables Pb detection with a dynamic range of nearly 2 (1.96), pMet-lead/Pb dissociation constant (K_d) 45.62 nM, and limit of detection 40 nM (0.832 μg/dL, 8.32 ppb). To mitigate earlier problems with lack of selectivity for Pb vs. zinc, we preincubated samples with tricine, a low-affinity zinc chelator. We validated pMet-lead measurements of characterized laboratory samples and unknown samples from six regions in Taiwan by inductively coupled plasma mass spectrometry (ICP-MS). Notably, two unknowns had Y/C ratios significantly higher than that of the control (3.48 ± 0.08 and 3.74 ± 0.12 vs. 2.79 ± 0.02), along with Pb concentrations (10.6 ppb and 15.24 ppb) above the WHO-permitted level of 10 ppb in tap water, while the rest four unknowns showing no detectable Pb upon ICP-MS. These results demonstrate that pMet-lead provides a rapid, sensitive means for on-site Pb detection in water from the environment and in living/drinking supply systems to prevent potential Pb poisoning.

In hepatocellular carcinoma (HCC), recurrence usually occurs after curative surgical resection. Currently, no approved adjuvant therapy has been shown to reduce recurrence rates. In this report, the in vivo mouse effect of sequential combination treatment with recombinant mouse interferon-alpha (rmIFN-α) and an anti-mouse-PD1 antibody on hepatitis B virus (HBV) clearance was evaluated. A phase I clinical trial was then conducted to assess the safety, tolerability, and inhibitory activity of sequential therapy with ropeginterferon alfa-2b and nivolumab in HCC recurrence in patients who have undergone curative surgery for HBV-related HCC. In animal modeling, HBV suppression was significantly greater with rmIFN-α and anti-PD1 sequential combination treatment than with their treatment alone. In the Phase I study, eleven patients completed the sequential therapy with ropeginterferon alfa-2b every two weeks at the dose of 450 µg for six doses, followed by three doses of nivolumab every two weeks up to 0.75 mg/kg. A notable decrease or clearance of HBV surface antigen was observed in two patients. Dose-limiting toxicity of grade 3 alanine transaminase and aspartate aminotransferase increases was observed in one patient. The maximum tolerated dose was determined. Currently no HCC recurrence has been observed. The treatment modality was well tolerated. The data support further clinical development of sequential combination therapy as a post-surgery prophylactic measure against the recurrence of HBV-related HCC.

Dravet syndrome (DS), also known as severe myoclonic epilepsy of infancy, is a rare and drug-resistant form of developmental and epileptic encephalopathies, which is both debilitating and challenging to manage, typically arising during the first year of life, with seizures often triggered by fever, infections, or vaccinations. It is characterized by frequent and prolonged seizures, developmental delays, and various other neurological and behavioral impairments. Most cases result from pathogenic mutations in the sodium voltage-gated channel alpha subunit 1 (SCN1A) gene, which encodes a critical voltage-gated sodium channel subunit involved in neuronal excitability. Precision medicine offers significant potential for improving DS diagnosis and treatment. Early genetic testing enables timely and accurate diagnosis. Advances in our understanding of DS's underlying genetic mechanisms and neurobiology have enabled the development of targeted therapies, such as gene therapy, offering more effective and less invasive treatment options for patients with DS. Targeted and gene therapies provide hope for more effective and personalized treatments. However, research into novel approaches remains in its early stages, and their clinical application remains to be seen. This review addresses the current understanding of clinical DS features, genetic involvement in DS development, and outcomes of novel DS therapies.

Few-shot classification is challenging since the goal is to classify unlabeled samples with very few labeled samples provided. It has been shown that cross attention helps generate more discriminative features for few-shot learning. This paper extends the idea and proposes two cross attention modules, namely the cross scaled attention (CSA) and the cross aligned attention (CAA). Specifically, CSA scales different feature maps to make them better matched, and CAA adopts the principal component analysis to further align features from different images. Experiments showed that both CSA and CAA achieve consistent improvements over state-of-the-art methods on four widely used few-shot classification benchmark datasets, miniImageNet, tieredImageNet, CIFAR-FS, and CUB-200-2011, while CSA is slightly faster and CAA achieves higher accuracies.

Epigallocatechin-3-gallate (EGCG) is the most abundant polyphenol in green tea. In this study, the effects of dietary EGCG on oxidative stress and the metabolism and toxicity of acetaminophen in liver were investigated. Rats were fed the diets with (0.54 %) or without EGCG supplementation for four weeks and were then intraperitoneally injected with acetaminophen (1g/kg). Results showed EGCG lowered hepatic oxidative stress and cytochrome P450 (CYP) 1A2, 2E1, and 3A, and UDP-glucurosyltransferase activities prior to acetaminophen injection. After acetaminophen challenge, the elevations in plasma alanine aminotransferase activity and histological changes in liver were ameliorated by EGCG treatment. EGCG reduced acetaminophen-induced apoptosis by increasing the Bax/Bcl2 ratio in liver. EGCG mildly increased autophagy by increasing the LC3B II/I ratio. Lower hepatic acetaminophen-glutathione and acetaminophen-protein adducts contents were observed after EGCG treatment. EGCG increased glutathione peroxidase and NAD(P)H quinone 1 oxidoreductase activities and reduced organic anion-transporting polypeptides 1a1 expression in liver after acetaminophen treatment. Our results indicate that EGCG may lower oxidative stress and reduce the metabolism and toxicity of acetaminophen. The reductions in CYP-mediated acetaminophen bioactivation and uptake transporter, as well as enhanced antioxidant enzyme activity, may limit the accumulation of toxic products in liver and thus lower hepatotoxicity

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

A high-resolution catalog for the 2014 Ms6.5 Ludian aftershocks was constructed based on the deep learning phase-picking model (CERP) and the seismic-phase association technology (PALM). A specific training strategy, which combines the advantages of the conventional short-long window average energy ratio algorithm (STA/LTA) and AI algorithm, is employed to retrain the CERP model. The P & S phases were accurately detected and picked on continuous seismic waveforms by the retained AI model. Hypoinverse and HypoDD were utilized for precise location of 3286 events. Compared to the previous results, our new catalog exhibits superior performances in terms of location accuracy and the number of aftershock events, thereby enabling a more de-tailed depiction of the deep-seated tectonic features. According to the distribution of aftershocks, it can be inferred that, (1) the seismogenic fault of Ludian earthquake is the NW-trending Baogunao-Xiaohe Fault. (2) the Ludian aftershocks interconnected the discontinuous NW-trending Baogunao-Xiaohe Fault, and intersected with the Zhaotong-Ludian Fault. (3) It suggests that the NE-trending Zhaotong-Ludian Fault may have been intersected by the NW-trending Baogunao -Xiaohe Fault, indicating that the Baogunao-Xiaohe Fault is likely a rela-tively young Neogene fault.

In this paper, we presented a method of retrieving sea surface wind speed from Sentinel-1 synthetic aperture radar (SAR) horizontal-horizontal (HH) polarization data in extra-wide mode, which have been extensively acquired over the Arctic for sea ice monitoring. In contrast to the conventional algorithm, i.e., using a geophysical model function (GMF) to retrieve sea surface wind by spaceborne SAR, we introduced an alternative method based on physical model guided neural network. Parameters of SAR normalized radar cross section, incidence angle, and wind direction are used as the inputs of the backward propagation (BP) neural network, and the output is the sea surface wind speed. The network is developed based on more than 11,000 HH-polarized EW images acquired in the marginal ice zone (MIZ) of the Arctic and their collocations with scatterometer measurements. Verification of the neural network based on the testing dataset yields a bias of 0.23 m/s and a root mean square error (RMSE) of 1.25 m/s compared to the scatterometer wind speed. Further comparison of the SAR retrieved sea surface wind speed with independent buoy measurements shows a bias and RMSE of 0.12 m/s and 1.42 m/s, respectively. We also analyzed the uncertainty of retrieval when the wind direction data of a reanalysis model are used as inputs to the neural network. By combining the detected sea ice cover information based on the EW data, one can expect to derive simultaneously sea ice and marine-meteorological parameters by spaceborne SAR in a high spatial resolution in the Arctic.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

In recent years, the taxonomy of the families of Phenuiviridae, Nairoviridae, and Peribunyavidae in Bunyavirales was updated frequently, because many novel viruses in these families have been identified and the species demarcation criteria of these families have been changed. As per these criteria and sequence analysis, we found that the taxonomy of 19 species in these families should be revised. We presented six proposals for optimizing virus species taxonomy using the examples from these families. First, the species demarcation criteria for the same family (e.g., Peribunyavidae) should be unified. Second, the methods and parameters for the taxonomic calculation in the same order (e.g., Bunyavirales) should be unified. Third, virus species taxonomy should be based on phylogenetic relationships, rather than a cutoff value of sequence identities that is a self-contradictory demarcation criterion, although sequence identities aid virus taxonomy greatly. Fourth, virus species taxonomy should be based on the phylogenetic relationship of a key viral gene (e.g., the RdRp gene of Bunyavirales), which is important for the taxonomy of virus recombinants or reassortants. Fifth, a virus can be demarcated without a species before its biomedical significance has been revealed. Sixth, names of all viruses and virus species should be constituted exclusively with common characters (English letters and Arab numbers), to minimize difficulty in spelling and communication. These proposals are rational, flexible, and can accommodate all known viruses. They can also bridge the taxonomy history and the future demands due to their flexibility.

Skeletal muscle is a specialized tissue consisting of nondividing and multinucleated muscle fibers. Skeletal muscle-specific myostatin (MSTN) is a secreted protein that acts as a negative regulator of muscle mass by inhibiting proliferation and differentiation of myoblasts. In this study, we established a screening platform to monitor myostatin promoter activity in rat L8 myoblasts. Extract of Glycyrrhiza uralensis (GUE), an oriental herbal medicine, was identified through this screening platform and, the active fractions of GUE were identified by process-scale liquid column chromatography system. For in vivo study, the GUE as a feed additive was investigated in growth-finishing pigs. The results showed that GUE significantly increased body weight, carcass weight and lean content in pigs. Microbiota analysis indicated that GUE did not affect the composition of gut microbiota in pigs. In summary, this established rodent myoblast screening platform was used to identify a myogenesis-related phytogenic, GUE, and further demonstrated that the active fractions inhibited MSTN expression. These finding suggest a novel application for GUE in growth performance enhancement through modulation of MSTN expression. Furthermore, this established screening platform has great potential for identification and evaluation of a wide variety of phytogenics involving in myogenesis.

In the field of computer vision, large-scale image classification tasks are both important and highly challenging. With the ongoing advances in deep learning and optical character recognition (OCR) technologies, neural networks designed to perform large-scale classification play an essential role in facilitating OCR systems. In this study, we developed an automatic OCR system designed to identify up to 13,070 large-scale printed Chinese characters by using deep learning neural networks and fine-tuning techniques. The proposed framework comprises four components, including training dataset synthesis and background simulation, image preprocessing and data augmentation, the process of training the model, and transfer learning. The training data synthesis procedure is composed of a character font generation step and a background simulation process. Three background models are proposed to simulate the factors of the background noise and anti-counterfeiting patterns on ID cards. To expand the diversity of the synthesized training dataset, rotation and zooming data augmentation are applied. A massive dataset comprising more than 19.6 million images was thus created to accommodate the variations in the input images and improve the learning capacity of the CNN model. Subsequently, we modified the GoogLeNet neural architecture by replacing the FC layer with a global average pooling layer to avoid overfitting caused by a massive amount of training data. Consequently, the number of model parameters was reduced. Finally, we employed the transfer learning technique to further refine the CNN model using a small number of real data samples. Experimental results show that the overall recognition performance of the proposed approach is significantly better than that of prior methods and thus demonstrate the effectiveness of proposed framework, which exhibited a recognition accuracy as high as 99.39% on the constructed real ID card dataset.

The Loropetalum chinense and Loropetalum chinense var. rubrum are typical and traditional ornamental and Chinese herbal medicine in Asia. However, more information is needed on the mechanisms underlying its flower coloring. Here, we profiled the flavonoid metabolome, full-length sequencing, and transcriptome analysis to investigate the flavonoid biosynthesis and global transcriptome changes among different petal coloring cultivars of L. chinense and L. chinense var. rubrum. The total anthocyanins and phenotypic of the petal were highly consistent with the petal color. Moreover, a total of 207 flavonoid components were identified. Of these, 12 flavonoid components were considered significantly different expression compounds among the four samples. Meanwhile, the first reference full-length transcriptome of L. chinense var. rubrum was being built, which had 171,783 high-quality non-redundant transcripts with correcting with next-generation sequencing (NGS). Among them, 52,851 transcripts were annotated in the seven database of NR, KOG, GO, NT, Pfam, Swiss-Port and KEGG. Combined with NGS analysis, the DETs involved in flavonoids and anthocyanins contributed greatest to the flower-coloring. Additionally, the different expressed of eight LcDFRs and four LcANS genes were positively correlated with flavonoid biosynthesis, and the four LcBZ1 and one Lc3Mat1 were positively correlated with the content of seven anthocyanins revealed by coupling with metabolomics and transcriptomics analysis. Together these results were used to mine candidate genes by analyzing flower coloring changes in a comprehensive metabolic and transcriptomic level in L. chinense and L. chinense var. rubrum.

This study delves into the complex dynamics of Underwater Wireless Optical Communication (UWOC) in varied Harbor water conditions. Focusing on four distinct types of Harbor water, the research employs the Monte Carlo method to simulate photon transmission and analyze critical UWOC characteristics. Key parameters such as the transmitted full divergence angle, received aperture, and Field of View (FOV) are meticulously evaluated for their impact on communication efficacy. The study first explores the relationship between laser power variation, attenuation length, and divergence angle, revealing how different water qualities influence received power and time delay spread. Notably, the received normalized power loss and time delay spread are found to be more significantly affected by communication distance than water quality. In addition, under the condition of small received aperture and FOV, the influence on normalized power loss and time spread is more obvious in Harbor water. The findings offer novel insights into the challenges of UWOC in Harbor waters, particularly in terms of light scattering and absorption properties, and contribute to the optimization of communication systems in such complex underwater environments. Furthermore, the analysis of time pulse spread in turbid water quality is of great significance for the analysis and improvement of underwater wireless optical timing, ranging and positioning.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

Ensuring equal access to affordable higher education for women and men has become a crucial target of UNESCO’s SDG4-Education 2030. Currently, about one-third of the world's college-age population participates in higher education, while the gender disparity persists in various systems. This study employed GDP per capita, gross enrollment ratio (GER), and the gender parity index (GPI) to demonstrate how the education systems have expanded resulting in the transformation of gender parity. We selected Japan, Korea, Taiwan, and the UK as research targets using a cross-correlation function and trend analysis to detect concurrent relationships and future trends with GDP per capita, GER, and GPI. The findings suggest Japan, Korea, and the UK continue to show gender disparity and need to respond to this issue in their policy intervention for SDG4-Education 2030. The results reveal a potential problem in the UK when GPI growth might become unlimited with females dominated. This study suggests the higher education expansion phenomenon and gender diversity in mass and universal systems can be detected by the trend analysis with GDP per capita, GER, and GPI in different settings. The design of the study provides an example to explore the gender diversity patterns in higher education systems for sustainable development.

Reducing fertilizer-N rate, applying nitrification inhibitor (NI), and incorporating straw are widely recommended to improve N use efficiency of crops and decrease N losses. However, how these practices affect crop N uptake by regulating the fertilizer-N fate during the growing season is not well understood. We conducted a field 15N tracer study to explore the effectiveness of reduced N application, NI, and straw incorporation on fertilizer-N fates for maize cultivation in Northeast China. The following six treatments were used: 1) no N fertilization (control); 2) 200 kg urea-N ha−1 (100%N); 3) 200 kg urea-N ha−1 and 2400 kg dry-straw ha−1 (100%N+S); 4) 160 kg urea-N ha−1 (80%N, i.e., 20% reduction of N fertilization); 5) 160 kg urea-N ha−1 and nitrification inhibitor (Nitrapyrin) (80%N+NI); 6) 160 kg urea-N ha−1, nitrification inhibitor and 2400 kg dry-straw ha−1 (80%N+NI+S). Our results showed that the five N fertilization treatments yielded 16%–25% more grain and 39%–60% more crop N uptake than the control receiving no N fertilizer, but the differences among the five treatments were not statistically significant. In contrast to plant growth, changes in fertilizer-N fates in soil and plant pools were more pronounced. Compared with the 100%N treatment, 20% fertilizer-N reduction (80%N) decreased 15N concentration in topsoil and plant pools but increased the proportion of plant 15N recovery at harvesting (N use efficiency, NUE15N, 60% vs. 50%) (P &lt; 0.05). Nitrapyrin co-application (80%N+NI) delayed soil nitrification and increased soil 15N retention at harvesting (52% vs. 36%), thereby decreasing NUE15N significantly (P &lt; 0.05). Straw incorporation (100%N+S) decreased fertilizer-N retention compared with NI co-application because it promoted NUE15N significantly (P &lt; 0.05). The combined application of NI and straw (80%N+NI+S) was more conducive to fertilizer-N retention in soil. Our findings demonstrate that NI and straw additions are efficient strategies for stabilizing fertilizer-N in soils and potentially minimizing N loss; however, their effects on NUE15N vary and the related mechanism must be further clarified in long-term trials.

Breast cancer is the most common malignancies in women and the second leading cause of cancer death in women. Triple negative breast cancer (TNBC) subtype is a breast cancer subset without ER, PR and HER2 expression, limiting treatment options and presenting a poorer survival rate. Thus, we investigated whether HDACi would be used as potential anti-cancer therapy on breast cancer cells. In this study, we found TNBC and HER2-enrich breast cancers are extremely sensitive to Panobinostat, Belinostat of HDACi via experiments of cell viability assay, apoptotic marker identification and flow cytometry measurement. On the other hand, we developed a bioluminescence based live cell non-invasive apoptosis detection sensor (IADS) detection system to evaluate the quantitative and kinetic analyses of apoptotic cell death by HDAC treatment on breast cancer cells. In addition, the use of HDACi may also be accompanied with chemotherapeutic agent such as doxorubicin to synergic drug sensitivity on TNBC cell (MDA-MB-231), but not in breast normal epithelia cells (MCF-10A), providing therapeutic benefits against breast tumor in clinic.

Xinjiang, as a climate-sensitive region in northwest China, holds significant importance in studying extreme weather events for agricultural production and socioeconomic development. Based on data from 52 meteorological stations and 23 extreme climate indicators in Xinjiang from 1960 to 2021, the 5a moving average, linear trend estimation, climate tendency rate, and GIS spatial analysis methods are used to analyze the distribution and change characteristics of extreme climate. The results revealed that from 1960 to 2021, TXx, TNx, TXn, TNn, FD, ID, TN10p, TX10p, and WSDI showed a significant upward trend, while SU, TR, TN90p, TX90p, and CSDI showed a significant downward trend. What is more, the range of changes in the extreme temperature indexes from 1990 to 2021 is higher than that of 1960 to 1989. The high-value areas of extreme indexes are primarily concentrated in the northern part, while the high-value areas of cold event indexes are mainly distributed in the southern part. The upward/downward trends all accounting for over 80.00% of the entire region. The Rx1day, Rx5day, PRCPTOT, R95p, R99p, R10, R20, and R25 showed a significant growth trend from 1960 to 2021, and the range of change in the extreme precipitation indexes from 1990 to 2021 was lower than that from 1960 to 1989. Moreover, their high-value areas and high climate tendency areas are mainly concentrated in the northern and western parts of Xinjiang, with upward trends all accounting for over 71.00% of the entire region. The research results provide theoretical foundations for formulating climate risk strategies in the northwest region of China.

In this work,the wave behaviour propagation of single-walled fluid conveying carbon nanotubes (SWCNT) under longitudinal magnetic fields and elastic foundations is studied, based on the nonlocal strain gradients theory(NSGT). With considertion of surface effect, the governing differential equation are obtained utilising Timoshenko beam theory and Hamilton's variational principle. The influence of small-scale parameters, fluid density, magnetic flux, surrounding elastic medium and surface effects on wave behaviour characteristics of carbon nanotubes are discussed in detail. The numerical results illustrated that with the magnetic flux increase，the phase velocities of the carbon nanotube will increase. When the fluid effects inside the carbon nanotube, the wave frequencies of the system reduces with increase in the non-local coefficient, while promotes with increase in the strain gradient coefficient. In addition, fluid density, surrounding elastic medium and surface effects have meaningful influence on the phase velocity of the system.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

The prediction of wind power output is part of the basic work of power grid dispatching and energy distribution. At present, the output power prediction is mainly obtained by fitting and regressing the historical data. The medium- and long-term power prediction results exhibit large deviations due to the uncertainty of wind power generation. In order to meet the demand for accessing large-scale wind power into the electricity grid and to further improve the accuracy of short-term wind power prediction, it is necessary to develop models for accurate and precise short-term wind power prediction based on advanced algorithms for studying the output power of a wind power generation system. This paper summarizes the contribution of the current advanced wind power forecasting technology and delineates the key advantages and disadvantages of various wind power forecasting models. These models have different forecasting capabilities, update the weights of each model in real time, improve the comprehensive forecasting capability of the model, and have good application prospects in wind power generation forecasting. Furthermore, the case studies and examples in the literature for accurately predicting ultra-short-term and short-term wind power generation with uncertainty and randomness are reviewed and analyzed. Finally, we present prospects for future studies that can serve as useful directions for other researchers planning to conduct similar experiments and investigations.

The microsporidium Nosema ceranae is a high prevalent parasite of the European honey bee (Apis mellifera). This parasite is spreading across the world into its novel host. The developmental process and some mechanisms of N. ceranae infected honey bees has been studied thoroughly, however, few studies have been carried out in the mechanism of gene expression in N. ceranae during infection process. We therefore performed suppressive subtractive hybridization (SSH) approach to investigate the candidate genes of N. ceranae during its infection process. Each 96 clones of infected (forward) and non-infected (reverse) library were dipped onto the membrane for hybridization. A total of 118 differentially expressed sequence tags (ESTs) had been sequenced. For the host responses, 20% of ESTs (13 ESTs, 10 genes and 1 non-coding RNA) from forward library and 83% of ESTs (44 ESTs, 28 genes) from reverse library were identified as differentially expressed genes (DEGs) of the hosts. High percentage of DEGs involved in catalytic activity and metabolic processes, revealed the host gene expression change after N. ceranae infection might lead to the unbalance of physiological mechanism. Among the ESTs from forward library, 75.4% ESTs (49 ESTs belonged to 24 genes) were identified as N. ceranae genes. Of 24 N. ceranae genes, nine DEGs were subjected to real-time quantitative reverse transcription PCR (real-time qRT-PCR) for validation. The results indicated that these genes showed highly up-regulated during N. ceranae infection. Among nine N. ceranae genes, one N. ceranae gene (AAJ76_1600052943) showed the highest expression level after infection. These identified differentially expressed genes from this SSH could provide information about the pathological effects of N. ceranae. Validation of nine up-regulated N. ceranae genes revealed highly potential for the detection of early nosemosis in the field and provide insight for further applications.

The universal health insurance system in Taiwan was formed with good intentions to help vulnerable groups. However, the possibility of bankrupting the system due to wasted medical resources. In this study, using the medical expenditures of the Taiwanese Government and gross domestic product (GDP) as variables, the wavelet analysis method was used to empirically study the correlations and leading-lagging relationships in quarterly data in the period from 1996 to 2016. In addition, the dependent population of the insured was used as the control variable. This population had no income and had high medical demands. Results: After the dependent population was included as a control variable, there was a period of low-frequency (one to four years short-term) linkage correlation, as well as a period of high-frequency (four to eight years long-term) linkage correlation. In addition, for more than eight years, there was also a high degree of linkage correlation, indicating that the linkage between medical expenditures and GDP occurred over the long term. Moreover, since medical expenditures positively affected GDP, one-way causality was observed. However, after 2008, regardless of whether a long or short term was examined, there was almost no linkage correlation. Before 2008, the medical expenditures of the government were positively correlated with economic growth; i.e., they enhanced economic growth. But, after 2008, this effect had already disappeared. The universal health insurance system has long been denounced as a waste of medical resources, and the waste must be immediately stopped. The government urgently needs to find a new solution.

As the lifespan of porous asphalt pavement extends, it invariably experiences performance degradation and an increase in tire/pavement noise compared with the original surface when it is newly built. To understand the medium-term performance of porous asphalt pavement during service and reveal the influence of different pavement performance indicators on tire/pavement noise generation, a seven-year continuous observation and data analysis study was conducted. Porous asphalt with different designed material parameters was taken into account, including thin-layer porous asphalt overlay with a maximum nominal aggregate size of 10mm (PUC-10), porous asphalt with a maximum nominal aggregate size of 13mm (PAC-13), and a two-layer porous asphalt incorporating both PUC-10 and PAC-13 (PUC-10+PAC-13). Using automated pavement technology testing equipment, key performance indexes, including damage rate (DR), rut depth (RD), international roughness index (IRI), and sideway force coefficient (SFC), were measured and calculated. The on-board sound intensity (OBSI) method was used to test noise levels in three types of porous asphalt pavement structures and on a dense graded easy compact asphalt concrete (ECA) for comparison. The progressions of the medium-term performances were analyzed according to the measured results. The correlations between tire/pavement noise levels and testing speed, testing lane, pavement structure, and road condition indicators were investigated by regression. The research results revealed that the DR and SFC of the three types of porous asphalt pavement displayed more significant attenuation in the service period, while the IRI and RD showed small changes. Among them, the SFC demonstrated significant attenuation over the first 4 years, decreasing between 13.8% and 17.0%. From the 3-7 years of operation, the transverse crack disease in porous asphalt pavement progressed rapidly. The three porous asphalt pavement structures tested exhibited commendable noise reduction capabilities. Compared to ECA, the OBSI noise levels of these structures were lower by 2.09 dB, 1.53 dB, and 2.88 dB, respectively. Compared to other pavement condition indicators, RD had a more significant impact on the OBSI value of the PUC-10 porous asphalt pavement. For the PUC-10+PAC-13 porous asphalt pavement, there was a significant linear relationship between the OBSI value and SFC, mainly due to polishing of the coarse aggregate surface. It leads to a decrease of the micro-texture, which lies in increasing tire/pavement noise at high-frequency ranges and decreasing SFC. This study will have guiding significance for the research of the attenuated law and durability improvement of porous asphalt tire/pavement noise.

In this paper, in order to reduce the energy consumption and delay of data transmission, the non-orthogonal multiple access (NOMA) and edge caching technologies are jointly considered. As for the cache-assisted vehicular NOMA-MEC networks, a problem of minimizing the energy consumed by vehicles (mobile devices, MDs) is formulated under the latency and resource constraints, which jointly optimizes the computing resource allocation, subchannel selection, device association, offloading and caching decisions. To solve the formulated problem, we develop an effective joint computation offloading and task caching algorithm based on the twin delayed deep deterministic policy gradient (TD3) algorithm. Such a TD3-based offloading (TD3O) algorithm includes a designed action transformation (AT) algorithm used for transforming continuous action space into a discrete one. In addition, to solve the formulated problem in a non-iterative manner, an effective heuristic algorithm (HA) is also designed. As for the designed algorithms, we provide some detailed analyses of computation complexity and convergence, and give some meaningful insights through simulation. Simulation results show that the TD3O algorithm may achieve lower local energy consumption than several benchmark algorithms, and HA may achieve a lower one than the completely offloading algorithm and local execution algorithm.

Mulberry leaves, when infected by pathogens, can suffer significant yield loss or even death if early disease detection and timely spraying are not performed. To enhance the detection performance of mulberry leaf diseases in natural environments and to precisely locate early small lesions, we propose a high-precision, high-efficiency disease detection algorithm named YOLOv8-RFMD. Based on improvements to You Only Look Once version 8 (YOLOv8), we first proposed the Multi Dimension Feature Attention (MDFA) module, which integrates important features at the pixel-level, spatial and channel dimensions. Building on this, we designed the RFMD Module, which consists of the Conv-BatchNomalization-SiLU (CBS) module, Receptive-Field Coordinated Attention (RFCA) Conv, and MDFA, replacing the Bottleneck in the model’s Residual block. We then employed Adown down sampling structure to reduce the model size and computational complexity. Finally, to improve the detection precision of small lesion features, we replaced the complete intersection over union (CIOU) loss function with the Normalized Wasserstein Distance (NWD) loss function. Results show that the YOLOv8-RFMD model achieves an mAP50 of 94.3% and an mAP50:95 of 67.8% on experimental data, representing increases of 2.9% and 4.3% respectively compared to the original model. The model size is reduced by 0.53 MB to just 5.45 MB, and the number of floating-point operations is reduced by 0.3 G to only 7.8 G. The improved model meets the deployment requirements of mobile embedded devices and can provide a theoretical reference for the automated spraying operations of mulberry leaves.

Plant diseases reduce crop yield and quality, hampering the development of agriculture. Fungicides, which restrict chemical synthesis, are the strongest controls for plant diseases. However, the harmful effects on the environment due to continued and uncontrolled utilization of fungicides has become a major challenge in recent years. Plant-sourced fungicides are a class of plant antibacterial substances or compounds that induce plant defenses. They can kill or inhibit the growth of target pathogens efficiently with no or low toxicity, degrade readily, do not prompt development of resistance, which has led to their widespread use. In this study, the growth inhibition effect of 24 plant-sourced ethanol extracts on rice sprigs was studied. Ethanol extract of gallnuts and cloves inhibited the growth of rice sprites by up to 100%. Indoor toxicity measurement results showed that the gallnut and glove constituents inhibition reached 39.23 μg/mL and 18.82 μg/mL, respectively. Extract treated rice sprigs were dry and wrinkled. Gallnut caused intracellular swelling and breakage of mitochondria , disintegration of nuclei, aggregation of protoplasts, and complete degradation of organelles in hyphae and aggregation of cellular contents. Protection of Rhizoctonia solani viability reached 46.8% for gallnut and 37.88% for clove in water emulsions of 1,000 μg/mL gallnut and clove in the presence of 0.1% Tween 80. The protection by gallnut was significantly stronger than that of clove. The data could inform the choice of plant-sourced fungicides for the comprehensive treatment of rice sprig disease. The studied extract effectively protected rice sprigs and could be a suitable alternative to commercially available chemical fungicides. Further optimized field trials are needed to effectively sterilize rice paddies.

Accurate estimation of Remaining Useful Life (RUL) for aircraft engines is essential for ensuring safety and uninterrupted operations in the aviation industry. Numerous investigations have leveraged the success of attention-based Transformer architecture in sequence modeling tasks, particularly in its application to RUL prediction. These studies primarily focus on utilizing onboard sensor readings as input predictors. While various Transformer-based approaches have demonstrated improvement in RUL predictions, their exclusive focus on temporal attention within multivariate time series sensor readings, without considering sensor-wise attention, raises concerns about potential inaccuracies in RUL predictions. To address this concern, our paper proposes a novel solution in the form of a two-stage attention based hierarchical transformer (STAR) frame-work. This approach incorporates a two-stage attention mechanism, systematically addressing both temporal and sensor-wise attentions. Furthermore, we enhance the STAR RUL prediction framework by integrate hierarchical encoder-decoder structures to capture valuable information across different time scales. By conducting extensive numerical experiments with the CMAPSS datasets, we demonstrate that our proposed STAR framework significantly outperforms current state-of-the-art models for RUL prediction.

Estimating the Remaining Useful Life (RUL) of aircraft engines holds a pivotal role in enhancing safety, optimizing operations, and promoting sustainability, thus being a crucial component of modern aviation management. Precise RUL predictions offer valuable insights into an engine’s condition, enabling informed decisions regarding maintenance and crew scheduling. In this context, we propose a novel RUL prediction approach in this paper, harnessing the power of Bi-directional LSTM and Transformer architectures, known for their success in sequence modeling, such as natural languages. We adopt the encoder part of the full Transformer as the backbone of our framework, integrating it with a self-supervised denoising autoencoder that utilizes Bidirectional LSTM for improved feature extraction. Within our framework, a sequence of multivariate time series sensor measurements serves as the input, initially processed by the Bidirectional LSTM autoencoder to extract essential features. Subsequently, these feature values are fed into our Transformer encoder backbone for RUL prediction. Notably, our approach simultaneously trains the autoencoder and Transformer encoder, different from the naive sequential training method. Through a series of numerical experiments carried out on the C-MAPSS datasets, we demonstrate that the efficacy of our proposed models either surpasses or stands on par with that of other existing methods.

Parallax processing and structure preservation has long been important and challenging tasks in image stitching. In this paper, an image stitching method based on sliding camera to eliminate perspective deformation and asymmetric optical flow to solve parallax is proposed. By maintaining the viewpoint of two input images in the mosaic non-overlapping area and creating a virtual camera by interpolation in the overlapping area, the viewpoint is gradually transformed from one to another image view-point so as to complete the smooth transition of the two image viewpoints and reduce perspective deformation. Two coarsely aligned warped images are generated with the help of a global projection plane. After that, the optical flow propagation and gradient descent method are used to quickly calculate the bidirectional asymmetric optical flow between the two warped images, and the optical flow-based method is used to further align the two warped images to reduce parallax. In the image blending, the softmax function and registration error are used to adjust the width of the blending area, further eliminating ghosting and reduce parallax. Finally, the comparative experiments show that our method can effectively eliminate perspective deformation, reduce misalignment, and save running time.

In this research, a design method for the graded triply periodic minimal surface (TPMS) structures with lightweight, high-strength, and high sound absorption properties is proposed. The graded TPMS structures are controlled by linear, quadratic, and sine functions. Uniform TPMS and graded TPMS were manufactured by laser powder bed fusion (LPBF) with AlSi7Mg powder, and an acoustic impedance tube test, compression test, and digital image correlation (DIC) test were ap-plied to obtain the sound absorption and compression properties. The sound absorption coefficient of a uniform Gyroid increases as the number of layers and surface thickness increase, and it in-creases as element size decreases. The sound absorption peak shifts to low frequencies as the number of layers increases. The sound absorption property of Type-Ⅰ graded TPMS is superior to the Type-Ⅱ, and the G-LinearⅠ has the highest sound absorption properties among the three functions. It reveals that the graded TPMS has superior sound absorption performance at low and medium frequencies. The compression and DIC results of graded TPMS also show excellent mechanical properties and energy absorption characteristics.

Bat feces were reported in ancient Chinese medicine books to have the effect of reducing heat and improving eyesight, but the mechanism of vision improvement still needs further research. To this end, we used 2,2-diphenyl-1-picrylhydrazyl (DPPH) and liquid chromatography/tandem mass spectrometry (LC/MS/MS) to analyze the antioxidant capacity of and the types of vitamins in bat feces. We hoped to screen the pharmacological components of bat feces, and to explain the role that these components may play in the treatment of visual deterioration. Our results found that bat feces had a good antioxidant capacity and mainly contain vitamins B1 (thiamine), B2 (riboflavin), B3 (nicotinamide), B3 (nicotinic acid), and B5 (pantothenic acid). Although these vitamins may help maintain the health of the optic nerve and cornea, the vitamin content of bat feces is low, but the heavy metal content is high, as shown using inductively coupled plasma mass spectrometry (ICP-MS) analysis. Therefore, we suggest that the use of bat feces as traditional Chinese medicine to improve vision should be strictly restricted.

The airflow carried by artificial aeration provides oxidant O2 for microbial growth and mineral dissolution in heap bioleaching. To investigate the effect of forced aeration rate on bioleaching of low-grade copper sulfide ores, column bioleaching experiments with six columns were conducted in the aeration range of 0~150 L/h at 30~45 ℃. The results showed that when the aeration rate was higher than 95 L/h, the proportions of heap settlement and fine particles mass were much greater than that without aeration. The final total Fe concentration and bacterial cell numbers in pregnant leach solution increased with the increase of aeration rate.The final concentrations of Cu2 + in the mother liquor under aeration conditions of 60-150 L / h were 1.411, 1.432, 1.498, 1.491 and 1.583 g / L, respectively, which were higher than 1.345 g / L under non-aeration conditions. When the aeration rate was 150 L / h, the final Cu leaching rate was 80.1 %, which was 11.4 % higher than that without aeration ( 68.7 % ). Furthermore, in the early stage of leaching, copper leaching rate with 95 L/h aeration rate remained the highest. 结论Artificial aeration accelerates the bioleaching of low-grade copper sulfide ores by improving porosity structure, temperature range of bacterial activity and microbial catalyzed dissolution of targeted minerals.

The load of power system changes with the development of economy, short-term load forecasting play a very important role in dispatching and management of power system. In this paper, the Ant Lion Optimizer (ALO) is introduced to improve the input weights and hidden-layer Matrix of extreme learning machine (ELM), after the parameters of ELM are optimized by ALO, then input nodes, hidden layer nodes and output nodes are determined, so a load forecasting model based on ALO-ELM combined algorithm is established. The proposed method is illustrated based on the historical load data of a city in China. The results show that the average absolute error of short-term load demand predicted by ALO-ELM model is 1.41, while that predicted by ELM is 4.34, the proposed ALO-ELM algorithm is superior to the ELM and meet the requirements of engineering accuracy, which proves the effectiveness of proposed method.

Mitochondrial DNA copy number (mtDNAcn) is associated with mitochondrial function contributing various diseases. Understanding of the association between mtDNAcn and infant neurodevelopment, as well as the role of racial disparities, remains unknown. A cohort study was conducted with 55 preterm infants and a single blood sample was collected from each infant during their NICU stay to measure mtDNAcn. NICU Network Neurobehavioral Scale (NNNS) and Bayley Scale of Infant Developmental testing Edition III was assessed during NICU until 2 years of corrected age (CA). Linear regression models were performed to investigate the relationship between the clinical characteristics, neurobehavioral outcomes and mtDNAcn. Majority of our subjects were male, White, non-Hispanic, had C-section, and without preterm premature rupture of membrane (PPROM). Increased mtDNAcn was found associated with younger birth gestational age (GA), nonoptimal neurodevelopment. However, the opposite associations between mtDNAcn and neurodevelopmental outcomes were observed between Black and White infants up to 1 year of CA. Adverse early life experience, together with increased mtDNAcn in White infants, and decreased mtDNAcn in Black infants may be considered as significant positive predictors of poor early life neurodevelopmental outcomes in infants.

The eco-efficiency of cultivated land use (ECLU) is an important indicator for the construction of ecological civilization in China. Exploring the spatiotemporal dynamic evolution of the ECLU is helpful for sustainable use of arable land, ensuring food security and ecological security. However, previous studies have mostly focused on the use of a slacks-based measure (SBM) model for ECLU measurement, ignoring the more accurate epsilon-based measure (EBM) model. Therefore, in this study, firstly, we explored the conceptual framework of ECLU, and then, based on the panel data of the counties in the region around Beijing and Tianjin from 2005 to 2020, we investigated the spatial and temporal evolution of ECLU by using the Super-EBM model, kernel density estimation method, and spatial Markov chain model. Results displayed: (1) From 2005 to 2020, the ECLU in the region around Beijing and Tianjin displayed an increasing state, but the average value was only 0.55. (2) The time evolution of the ECLU has gradually polarized, the internal gap has widened, but it tends to stabilize. (3) The ECLU in the region around Beijing-Tianjin was more inclined to keep it the same and there was a "club convergence" phenomenon, which was meaningfully affected by the background of neighboring areas. In the light of local conditions, the government should reasonably formulate the path to optimize the ECLU, strengthen the linkage with the surrounding cities, and bring into play the positive spillover effect.

In this study, we evaluated the effects of Cyclosporine A (CsA) on Lipopolysaccharide (LPS)-induced cytokine production in the genital tract of female rabbits. Twelve sexually mature and healthy female rabbits were randomly divided into four groups (n = 3 each). The rabbits in the LPS group were given an intrauterine infusion of Escherichia coli LPS (4 mg/kg body weight (BW)). Rabbits in the CsA group were given CsA (20 mg/kg BW). Rabbits in the LPS + CsA group were given LPS (4 mg/kg BW) and CsA (20 mg/kg BW). The control group received only LPS and CsA carrier. The gene expression and protein levels of pro- and anti-inflammatory cytokines were observed using qRT-PCR and immuno-histochemical (IHC) assay, respectively. Our study showed that IL-1β, IL-6, IL-8, TNF-α, IFN-γ, IL-4, IL-10, IL-13, and TGF-β were expressed in female genital organs. The LPS challenge increased the mRNA expression of IL-6 and TNF-α in the uterine body and IL-1β in the uterotubal junction compared to the control group. CsA increased the basal mRNA expression of anti-inflammatory cytokines (i.e., IL-4 in the uterine body, uterotubal junction, and oviductal ampulla; IL-10 in the cervix, oviductal isthmus, and ampulla; and TGF-β in the uterotubal junction and oviductal ampulla) and pro-inflammatory cytokines (i.e., IL-6 and IL-8 in the cervix; IL-1β in the oviductal isthmus; TNF-α in the oviductal ampulla; and IFN-γ in the uterine body compared to the control group). In addition, CsA inhibited the mRNA expression of pro-inflammatory cytokines, such as IL-6 in the uterine body, uterotubal junction, and oviductal isthmus; TNF-α in the uterine body; and IFN-γ in the uterotubal junction and oviductal isthmus induced by the LPS challenge. The IHC assay showed the LPS-induced increase in protein production of IL-6 in the uterine body and oviductal isthmus. CsA increased the protein production of IL-10 in the cervix, uterine body, oviductal ampulla, and isthmus. Moreover, CsA decreased the protein production of IL-6 in the uterine body and oviductal isthmus induced by LPS.

The microstructure of Al-5Fe-1.5Er alloy was characterized and analyzed by using XRD, SEM, TEM and EDS. The effect of microstructure on the behavior of crack initiation and propagation was investigated by in situ tensile testing. Results show that the microstructure consists of α-Al matrix, Al₃Fe, Al₄Er, eutectic phase Al₃Fe + Al₄Er, while the 1.5 wt.% Er was added in Al-5Fe alloy. The twin structure of the Al₃Fe phase was observed, and the twin plane is {001}. Moreover, a continuous concave and convex interface structure of the Al₄Er has been found. Al₃Fe is in the form of a sheet with a clear gap inside.In situ tensile tests of the alloy at room temperature show that the crack initiation occured mainly in the Al₃Fe phase, and that the crack propagation modes include intergranular and transgranular expansion. Crack transgranular expansion is due to the strong binding ability between Al₄Er phases and surrounding organization, and the continuous concave and convex interface structure of the Al₄Er provides a significant meshing effect on the matrix and eutectic structure.

The shield tunnels inevitably endure various damage with the service time increasing. Meanwhile, steel corrugated plate has been used extensively in multiple conditions and proved effective to strengthen the segmental joints by full-scale tests. A numerical model is proposed to probe the feasibility of using new Stainless Steel Corrugated Plate (SSCP) to reinforce the shield tunnel segments. A new method, called virtual tracking element technology, is employed to achieve the simulation of realistic stress state of the segmental joint. Moreover, the segmental joint component analysis and parametric study are conducted based on the numerical model. The results demonstrate that: (1) the virtual tracking element technology proves valid and efficient to simulate the secondary stress state of segmental joint; (2) SSCP reinforcement is not fully utilized when the grade of segmental concrete is C50 and it has abundant safety margin for potential overload; (3) SSCP reinforcement is well-performed regardless of the burial depth and reinforcement in advance is recommended.

The article presents a literature review of three Chinese manuscripts containing natural dyes recipes and three containing synthetic dyes from the Ming Dynasty to the Republican Period. The manuscripts mentioned were exclusively used as references and sources. Four databases were used to access the original documents, then, a translation from old mandarin to Spanish was made. For natural dyes, the results show four dyestuffs were commonly used to produce colors, sappanwood (Caesalpinia sappan L.), followed by safflower (Carthamus tinctorius L.), indigo (Indigofera tinctoria L.), and sophora (S. japonicum L.). While the synthetic dyes exported to or produced in China were mainly bluish, greenish, and violet probably because they were difficult to obtain from natural ones. The literature review of the dyes and their recipes can be a key factor in any art history or conservation study, improving the understanding of how the colors were achieved and as complementary information for analytical analyses. It provides useful details that contribute to the preservation of Chinese dye history on silk heritage.

The newly established virus family Phenuiviridae in Bunyavirales harbors viruses infecting three kingdoms of host organisms (animals, plants, and fungi), which is rare in known virus families. Many phenuiviruses are arboviruses and replicate in two distinct hosts (e.g., insects and humans or rice). Multiple phenuiviruses, such as Dabie bandavirus, Rift Valley fever phlebovirus, and Rice stripe tenuivirus, are highly pathogenic to humans, animals, or plants. They impose heavy global burdens on human health, livestock industry, and agriculture and are research hotspots. In recent years the taxonomy of Phenuiviridae has been expanded greatly, and researches on phenuiviruses have made significant progress. With these advances, this review drew a novel panorama regarding the biomedical significance, distribution, morphology, genomics, taxonomy, evolution, replication, transmission, pathogenesis, and control of phenuiviruses, to aid researchers in various fields to recognize this highly adaptive and very important virus family.

Signal preprocessing and feature extraction are two important and necessary steps of data analysis. In signal analysis, typically these two steps are implemented through multiple algorithms. Moreover, the significant parameters in most algorithms are set empirically. We have developed an algorithm that can preserve and highlight characteristic waveforms while attenuating non-feature waveforms. The parameters in the algorithm are set through difference analysis. We have conducted experiments on both clinical and open-source ECG data, obtaining effective test results.

Establishment of mixed-forests has gained increasing attention as a way to optimize forest production, to improve ecological benefits and as a safety net for impacts of future climate uncertainties. However, practical knowledge about which species and what proportion of them should be mixed is still lacking. Thus, this study was conducted with the aim of identify suitable species for mixture with Acacia cincinnata. The mixture tested in the present study was A. cincinnata + Eucalyptus robusta (6:4), A. cincinnata + Acacia mangium (3:1) and monospecifc plantation of A. cincinnata established in 2014. After 7 years of growth, we analyzed the effects of species mixture on growth of tree species, understory vegetation and soil physico-chemical properties as well as bacterial community structure and diversity. The results showed that species mixture had no significant effect on growth characteristics, such as diameter and singletree volume of A. cincinnata. However, mixed-species planting increased the total stocking volume compered to monospecific plantation of A. cincinnata. Furthermore, stand mixture significantly increased species diversity, biomass and nutrient stocks in the understory vegetation. The soil of mixed stand of A. cincinnata and A. mangium had the highest C and N contents, whereas the soil of pure A. cincinnata stand had the highest P content. The diversity of soil bacterial community were the highest in the mixed stand of A. cincinnata and E- robusta, followed by pure A. cincinnata stand and A. cincinnata + A. mangium stand. The relative abundance of Proteobacteria and Actinobacteria was higher in soils of mixed stands. Furthermore, the relative abundance of Firmicutes was high in the soil of A. cincinnata + A. mangium while the relative abundance of Verrucomicrobia was high in A. cincinnata + E. robusta stand. As a whole, the study demonstrated that establishing mixed-species plantation enhance the diversity and composition of understory vegetation, soil physico-chemical and soils bacterial community; thereby increasing biodiversity, nutrient cycling and carbon sequestration in the biomass and soil. From the viewpoints of forest productivity and ecological benefits, it is advisable to establish a mixed plantation of A. cincinnata and A- mangium in southern China. As a whole, our work revealed that the sustainability of mixed-species plantation relies on the interactions between soil attributes, vegetation, and bacterial community.

Classical laws of friction suggest that friction force is proportional to the normal load and independent of the nominal contact area. As a great improvement in this subject, it is now widely accepted that friction force is proportional to the real area in contact, and much work has been conducted based on this hypothesis. In present study, this hypothesis will be carefully revisited by measuring the friction force and real contact area in-site and real-time at both normal loading and unloading stages. Our experiments reveal that the linear relation always holds between friction force and normal load. However, for the relation between friction force and real contact area, the linearity holds only at the loading stage while fails at the unloading stage. This study may improve our understanding of the origin of friction.