In recent years, with the increasing research and development of the LED industry which contains GaN, it is expected that there will be a large amount of related wastes in the future. Especially the gallium has extremely high value of economic, therefore, it is necessary to establish the recycling system of the GaN waste. However, GaN is a direct-gap semiconductor and with high energy gap, high hardness, and high melting point make it difficult to recycle. Therefore, this study will analyze the physical characteristics of LED wastes containing GaN and carry out various leaching method to leach the valuable metals from the waste optimally. Different acids are used to find out the best reagent for leaching the gallium. Different experimental parameters are discussed such as the effect of the different acid agents , concentration, pressure, solid-liquid mass ratio, temperature, and time which influence the leaching efficiency of the gallium. In this study, various leaching methods which effect the leaching efficiency of the gallium are compared and the advantages and disadvantages are discussed. Finally, pressurized acid leaching method is preferred to leach the GaN waste, and hydrochloric acid is used as the leaching solution because of its better leaching efficiency of gallium. Eventually, the leaching efficiency of the gallium can reach to 98%.

Novel high energy density materials N14 (1,6-dihydro-1,2,3,3a,4,5,5a,6,7,8,8a,9,10,10a-tetradecazapyrene) and N18 (1,2,2a,3,4,4a,5,6,6a,7,8,8a,9,10,10a,11,12a-octadecazacoronene) were designed, and their structures, detonation performance and stabilities were calculated employing density functional theory (DFT). Calculations reveals that they have a good balance between high energy and stability. Their energy gaps between LUMO and HOMO are all lower than that of TATB, while their impact sensitivity h_50% is estimated close to that of RDX. Concerning energy, detonation performance of the N14 (P = 43.6 GPa, D = 10040 m/s, Q = 2214 cal/g) and the N18 (P = 37.4 GPa, D = 9400 m/s, Q = 2114 cal/g) are comparable to CL-20.

Control charts have been widely used for monitoring process quality in manufacturing and play an important role in triggering a signal in time when detecting a change in process quality. Many control charts in literature assume that the in-control distribution of the univariate or multivariate process data is continuous and not categorical. This research develops two exponentially weighted moving average (EWMA) proportion control charts for monitoring a process with multinomial proportions when considering both large and small sample sizes. For a large sample size , the charting statistic depends on the well-known Pearson χ2 statistic, and the control limit of the EWMA proportion chart is determined by an asymptotical chi-square distribution. For a small sample size, we derive the exact mean and variance of the Pearson χ2 statistic. Hence, the exact EWMA proportion chart is determined. The proportion chart can also be applied to monitor the distribution-free continuous multivariate process as long as each categorical proportion associated with specification limits of each quality variable is known or estimated. Lastly, we investigate the detection performance of the proposed EWMA proportion chart by numerical analyses. Real data analysis demonstrates the beneficial application of the proposed EWMA proportion charts.

Concussion, also known as mild traumatic brain injury (mTBI), commonly causes transient neurocognitive symptoms, but in some cases, it causes cognitive impairment, including working memory (WM) deficit, which can be long-lasting and impede a patient’s return to work. The predictors of long-term cognitive outcomes following mTBI remain unclear because abnormality is often absent in structural imaging findings. The purpose of the study was to determine whether machine learning-based models using functional magnetic resonance imaging (fMRI) biomarkers and demographic or neuropsychological measures at baseline could effectively predict 1-year cognitive outcomes of concussion. We conducted a prospective, observational study of patients with mTBI who were compared with demographically-matched healthy controls enrolled between September 2015 to August 2020. Baseline assessments were collected within the first week of injury, and follow-ups were conducted at 6 weeks, 3 months, 6 months, and 1 year. Potential demographic, neuropsychological, and fMRI features were selected according to the significance of correlation with the estimated changes in WM ability. The support vector machine classifier was trained using these potential features and estimated changes in WM between the predefined time periods. Patients demonstrated significant cognitive recovery at the third month, followed by worsened performance after 6 months, which persisted until 1 year after concussion. Approximately half of the patients experienced prolonged cognitive impairment at 1-year follow up. Satisfactory predictions were achieved for patients whose WM function did not recover at 3 months (accuracy=87.5%), 6 months (accuracy=83.3%), 1 year (accuracy=83.3%), and performed worse at 1-year follow-up compared to baseline assessment (accuracy=83.3%). This study demonstrated the feasibility of personalized prediction for long-term postconcussive WM outcomes based on baseline fMRI and demographic features, opening a new avenue for early rehabilitation intervention in selected individuals with possible poor long-term cognitive outcomes.

In nature and engineering applications, flexible fiber beds covering biological surfaces can play a role in reducing resistance. These fibers deform under the action of fluids, and this deformation affects the fluid flow state, forming a complex fluid-solid interaction phenomenon. To quantitatively analyze such issues, the physical model is simplified to the deformation problem of an soft hair bed caused by Stokes flow, and the deformation problem of a single fiber caused by Stokes flow is further studied. The deformation problem of an elastic single fiber in a channel caused by Stokes flow can be described by a nonlinear integral equation. We have obtained a new series solution, which has been compared with the previous perturbation method to verify the accuracy and effectiveness of the series solution. Meanwhile, we have further provided an extended form of flexible fiber deformation through experimental fitting. This fluid-solid interaction problem involves multiple fields and is very important in many natural and engineering systems. The research in this paper can not only help us better understand complex phenomena in nature but also delve into the interaction mechanism between fluids and solids, providing a theoretical basis for future scientific research and engineering applications.

Pristimerin (PM) is a naturally occurring quinonemethide triterpenoid compound that isolated from the Celastraceae and Hippocrateaceae families. Its anticancer effects have attracted a great deal of attention, but the mechanisms of action remain obscure. In this study, we screened for the active compounds of Pristimerin using a drug-likeness approach. Potential protein targets of Pristimerin were predicted by PharmMapper and Coremine database. Candidate protein targets were then uploaded to GeneMANIA and GO pathway analysis. Finally, compound-target, target-pathway, and compound-target-pathway networks were constructed using Cytoscape 3.3. The results showed that Pristimerin had good drug ability and identified 13 putative protein targets. Network analysis revealed that these targets are associated with cancer, inflammation and other physiological processes. In summary, Pristimerin is predicted to target a variety of proteins and pathways to form a network that exerts systemic pharmacological effects.

Aqueous Zinc ion batteries (ZIBs) possess significant potential in large energy storage systems due to their cost-effectiveness and environmental protection. However, the limited voltage window and poor reaction kinetics of the cathode material are still bottlenecks, restricting the further development of ZIBs. In this work, we rationally design Ni-doped V2O5@3D Ni core/shell composite on carbon cloth electrode (Ni-V2O5@3D Ni@CC) by growing Ni-V2O5 on the free-standing 3D Ni metal nanonets for high-voltage and high-capacity ZIBs. Impressively, the embedded Ni doping increases the interlayer spacing of V2O5, extending the working voltage and improving the Zn2+ kinetics reaction of the cathode materials, at the same time the 3D structure with high specific surface area and superior electronic conductivity benefits to fast Zn2+ transport. Consequently, the as-designed Ni-V2O5@3D Ni@CC cathodes can operate within a wide voltage window from 0.3 to 1.8 V vs. Zn/Zn2+ and deliver a high capacity of 270 mAh g-1 at a high current density of 0.8 A g-1. In addition, the reversible Zn2+ (de)-incorporation reaction mechanisms in the Ni-V2O5@3D Ni@CC cathodes are investigated by multiple characterization methods. As a result, we achieve a big step toward the practical applications of commercial ZIBs.

Bloodstream infection is a major health problem worldwide, with extremely high mortality. Detecting infection in the early stage is challenging due to the extremely low concentration of bacteria in the blood. Digital PCR provides unparalleled sensitivity and can achieve absolute quantification, but it is time-consuming. Moreover, the presence of unavoidable background signals in negative controls poses a significant challenge for single-molecule detection. Here, we propose a novel strategy called “Ultrafast flexible thin tube-based droplet digital PCR (utPCR)” that can shorten the digital PCR process from 2 hours to only 5 minutes, with primer annealing/extension time reduced from minutes to only 5 seconds. Importantly, the ultrafast PCR eliminates the nonspecific amplification and thus enables single-molecular detection. The utPCR enabled sensitive detection and digital quantification of E. coli O157 in the high background of 106-fold excess of E. coli K12 cells. Moreover, this method also displayed the potential to detect rare pathogens in blood samples, and the limit of detection (LOD) could be as low as 10 CFU per mL of blood without false positive results. Considering ultrafast (<5 min) and highly sensitive (single-molecule detection), the utPCR holds excellent prospects in the next generation of molecular diagnosis.

Extensive post reproductive lifespan (PRLS) is observed only in a few species, such as humans or resident killer whales, and its origin is under debate. Hypotheses like mother-care and grandmother-care invoke strategies of investment—provision to one’s descendants to enhance one’s overall reproductive success—to explain PRLS. The contribution of an investment strategy varies with the age of the caregiver, as the number of care-receiving descendant changes with age. Here we simulated an agent based model, which is sensitive to age-specific selection, to examine how the investment strategies in different hypotheses affect survival and reproduction across different stages of life. We found that extensive PRLS emerges if we combine multiple investment strategies, including grandmother-care but not mother-care, which allow an individual to have an increasing contribution as it ages. We also found that, if mother-care is further introduced to the PRLS-enabling strategies, it will let contribution at mid-life to substitute contribution at late life, which consequently terminates extensive PRLS.

To improve the interfacial compatibility between cement matrix and expanded polystyrene (EPS) in the core-shell lightweight aggregates (CSLA), the effects of sodium silicate, Polyvinyl alcohol (PVA) emulsion, Vinyl acetate-ethylene (VAE) emulsion, acrylic acid, and acetic acid on the cement-EPS interface were investigated. The denseness of the interface was studied by scanning electron microscopy (SEM), and the effect of interfacial agents on the hydration process of cement was studied by the heat of hydration and induction resistivity. The macroscopic properties of the interface of the CSLA were characterized by the "leak-white" rate, drop resistance and numerical crushing strength. The results show that the sodium silicate densifies the interface by generating hydration products on the EPS surface. At the same time, organic acid enhances the interfacial properties of EPS and cement by increasing the surface roughness and allowing hydration products to grow in the surface micropores. In terms of the cement hydration process, both two interfacial agents delay the cement hydration. Above all, with comprehensive interface properties, "leak-white" rate, and mechanical properties, VAE emulsion and sodium silicate can achieve the best performance with a final crushing resistance of 5.7 MPa.

For planetary gear has the characteristics of small volume, light weight and large transmission ratio, it is widely used in high speed and high power mechanical system. Poor working conditions result in frequent failures of planetary gear. A method is proposed for diagnosing faults in planetary gear based on permutation entropy of Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN) Adaptive Neuro-fuzzy Inference System (ANFIS) in this paper. The original signal is decomposed into 6 intrinsic mode functions (IMF) and residual components by CEEMDAN. Since the IMF contains the main characteristic information of planetary gear faults, time complexity of IMFs are reflected by permutation entropies to quantify the fault features. The permutation entropies of each IMF component are defined as the input of ANFIS, and its parameters and membership functions are adaptively adjusted according to training samples. Finally, the fuzzy inference rules are determined, and the optimal ANFIS is obtained. The overall recognition rate of the test sample used for ANFIS is 90.75%, and the recognition rate of gear with one missing tooth is relatively high. The recognition rates of different fault gears based on the method can also achieve better results. Therefore, the proposed method can be applied to planetary gear fault diagnosis effectively.

Candida albicans is a major fungal pathogen of humans, accounting for 15% of nosocomial infections with an estimated attributable mortality of 47%. C. albicans is usually a benign member of the human microbiome in healthy people. Under constant exposure to highly dynamic environmental cues in diverse host niches, C. albicans has successfully evolved to adapt to both commensal and pathogenic lifestyles. The ability of C. albicans to undergo a reversible morphological transition from yeast to filamentous forms is a well-established virulent trait. Over the past few decades, a significant amount of research has been carried out to understand the underlying regulatory mechanisms, signaling pathways, and transcription factors that govern the C. albicans yeast-to-hyphal transition. This review will summarize our current understanding of well-elucidated signal transduction pathways that activate C. albicans hyphal morphogenesis in response to various environmental cues and the cell cycle machinery involved in the subsequent regulation and maintenance of hyphal morphogenesis.

With the offshore oil-gas fields entering decline phase, high-efficiency separation of oil-gas-water mixtures becomes a significant challenge. As essential equipment for separation, the three-phase separators play a key role in Offshore Oil-Gas production. However, level control is critical in the operation of three-phase gravity separators on offshore facilities, as it directly affects the efficacy and safety of the separation process. This paper introduces an advanced deep deterministic policy gradient with adaptive learning rate weights (ALRW-DDPG) control algorithm, which improves the convergence and stability of the conventional DDPG algorithm. An adaptive learning rate weight function is meticulously designed, and an ALRW-DDPG algorithm network is constructed for simulating three-phase separator liquid level control. The effectiveness of the ALRW-DDPG algorithm is subsequently validated through simulation experiments. The results show that the ALRW-DDPG algorithm achieves a 15.38% improvement in convergence rate compared to the traditional DDPG algorithm, and the control error is significantly smaller than that of PID and DDPG algorithms.

Nickel base superalloy GH4169 is a material with strong mechanical properties and is difficult to process. In order to reduce tool wear during material processing and improve workpiece surface processing quality, based on the finite element simulation software DEFORM, the influence of n, ap, and fz parameters on tool wear during carbide tool milling GH4169 was studied, and a simulation orthogonal experimental model was established, The prediction model of tool wear is obtained; The ultrasonic vibration milling is compared with ordinary milling, and the improvement degree of different coating materials on carbide tool wear is explored. The results show that the ultrasonic vibration signal is helpful to reduce tool wear, improve the surface quality of the workpiece, and improve the stability of the milling process. TIALN/TIN (WC) composite coated tools have good cutting performance, help to reduce tool temperature, reduce tool wear, and improve tool life.

We analyze a time-delayed SIQR model that considers the transportation-related infections and entry-exit screening. This model aims to determine the measures for preventing and controlling major emergent infectious diseases and the associated costs. We calculate the basic reproduction number (R0), apply the linearization method, and construct an appropriate Lyapunov function to determine the stability of the disease-free equilibrium in the local and global. We collect COVID-19 infection data from two regions in the United States in 2020 for data fitting, obtain a set of optimal parameter values, and show that the model is suitable for simulating the outbreak and spread of emerging infectious diseases. We find that transportation-related infections increase the basic reproduction number, enhancing the impact on disease spread. Entry-exit screening effectively suppress the spread of disease by reducing the basic reproduction number. Furthermore, we investigate the influence of the incubation period on disease and find that a shorter incubation period results in a shorter duration but a larger scale of infection, and the peaks are reduced. We conduct a sensitivity analysis of the R0 and propose three measures to prevent the spread of new infectious diseases based on the most sensitive parameters: wearing masks, implementing urban closures, and administering medication to sick but not yet hospitalized patients promptly. In the case of COVID-19, we use Pontryagin’s minimum principle to get time-varying control measures to control the spread of the outbreak. Optimal control effectively controls the development and deterioration of the disease. Finally, several control measures are compared through cost-effectiveness analysis, and the results show that wearing masks is the most cost-effective measure. Our study provides some practical guidance for controlling the spread of major emerging infectious diseases.

We give a simple proof of the Chen inequality for the Chen invariant $\underbrace{\delta (2,...,2)}_{k\mbox{ terms}}$ of submanifolds in Riemannian space forms.

Chlorophyll a concentration (Chl) is a key variable to estimate primary production (PP) through ocean color remote sensing (OCRS). Accurate Chl estimate is crucial for better understanding of spatio-temporal trends of PP over recent decades as a consequence of climate change. However, a number of studies have reported that currently operational chlorophyll a algorithms perform poorly in the Arctic Ocean (AO), which is mainly caused by the interference of colored and detrital material (CDM) with the phytoplankton signal in the visible part of the spectrum. To determine how and to what extent that CDM would bias the estimation of Chl, we evaluated the performances of 8 currently available ocean color algorithms: OC4v6, OC3Mv6, OC3V, OC4L, OC4P, AO.emp, GSM01 and AO.GSM. Our results suggest that the empirical AO.emp algorithm performs the best overall, but for waters with high CDM (acdm(443) &gt; 0.067 m-1), which is of much interest in the Arctic, it is the two semi-analytical GSM models that show better performance. Besides, sensitivity analyses using an Arctic spectrally- and vertically-resolved primary production model further show that errors in Chl mostly propagate proportionally to PP estimates with 7% amplification at maximum. We aslo demonstrate that the higher level of CDM relative to Chl in the water column, the larger the bias would occur in both Chl and PP estimates. Although the AO.GSM overall best performs among algorithms tested in the present study, it tends to fail for a significant number of pixels (16.2% observed in the present study) particularly for waters with high CDM. Our results suggest that an algorithm that provides reasonable Chl estimates for a wide range of optically-complex Arctic waters is still required.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

The greatly diversified flowering plants (angiosperms) are the dominating and defining group in the current earth ecosystem. However, from which group by what way the flowers, especially their gynoecia (key characteristics of angiosperms), are derived have been the questions in botany unanswered over centuries. Such an embarrassing situation can be attributed to the lack of plants with partially enclosed ovules, which are supposed to be a post between gymnosperms and angi-osperms. Here we report a fossil plant that has an apparent coniferous vegetative and reproduc-tive morphologies but has a single seed partially wrapped by the subtending bract. Such a mor-phology suggests that the carpels in angiosperms may be equivalent to bracts enclosing their axil-lary seed(s). Such a non-traditional interpretation of the homology of angiosperm carpels is com-patible with various new progresses made in botany and is in line with Tomlinson’s recent hy-pothesis. Together with other fossil evidence reported recently, it appears that gynoecia in angio-sperms are derived in multiple ways.

Endoscopic medical images can suffer from uneven illumination, low contrast, and lack of texture information due to the use of point directional light sources and the presence of narrow tissue structures, posing diagnostic difficulties for physicians. In this paper, a deep learning-based su-pervised illumination enhancement network is designed for low-light endoscopic images, aiming to improve both global illumination and local details. Initially, a global illumination enhancement module is formulated utilizing a higher-order curve function to improve global illumination. Sec-ondly, a local feature extraction module incorporating dual attention is designed to capture local detailed features. Considering the significance of color fidelity in biomedical scenarios, the designed loss function prioritizes introducing color loss to alleviate image color distortion. Compared with seven state-of-the-art enhancement algorithms on Endo4IE endoscopic datasets, experimental re-sults show that the proposed method can better enhance low-light endoscopic images and avoid image color distortion. It provides an efficient method to enhance images captured by endoscopes which can effectively assist clinical diagnosis and treatment.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

The Chen circuit system, a three-dimensional autonomous system with intriguing dynamics, has gained considerable attention due to its potential applications in diverse scientific fields. In this article, a Chen circuit-like system is defined and a comprehensive dynamics has been studied. The system exhibits chaotic dynamics, limit cycles, and bifurcations, making it a captivating subject of study. By employing numerical simulations and analytical techniques, we explore the system's stability and identify critical parameter values leading to qualitative changes. Notably, we delve Hopf bifurcations, which give rise to stability changes and the emergence of limit cycles. Furthermore, we analyze the fractal dimension of the system's attractor, providing insights into its complexity and self-similarity. Through a systematic examination of the Chen circuit-like system, we deepen our understanding of its intricate dynamics and offer valuable insights into the underlying mechanisms. The findings contribute to the field of dynamical systems and hold potential implications in areas such as chaos-based secure communications, signal processing, and nonlinear control. This work serves as a valuable reference for researchers and practitioners interested in the dynamics and bifurcation analysis of nonlinear systems.

A series of novel N-n-butyl-1,8-naphthalimide derivatives were synthesized via a three-step reaction involving nucleophilic substitution and acylation. All of the compounds were characterized by IR, ¹H NMR, ¹³C NMR, MS, and elemental analysis, and the crystal structure of N-n-butyl-4-[N’,N’-bis(2`,4`-dichlorobenzoyl)ethylamino]-1,8-naphthalimide was determined. The π-π stacking interactions and hydrogen bonds between the two molecular core planes (naphthalimide ring) and the van der Waals forces between the flexible n-butyl groups resulted in a 3D long-chain structure. The UV-vis and fluorescence properties of the title compounds were investigated. The results indicated that the monosubstituted 1,8-naphthalimide derivatives bearing an electron-donating group on the benzene ring or a structure with a larger conjugative effect exhibited enhanced fluorescence properties.

MicroRNAs (miRNAs) are a class of small non-coding RNAs, which function as regulators of gene expression and contribute in numerous physiological processes. However, little is known referring to miRNAs function in insect chemosensation. In the current study, nine small RNA libraries were constructed and sequenced from the antennae of nymphs, adult males and females of Apolygus lucorum. In total, 399 miRNAs were identified including 275 known and 124 novel miRNAs. Known miRNAs were classified into 71 families, amongst which, 23 families were insect-specific. Expression profile analysis showed that miR-7-5p_1 was the most abundant miRNAs in the antennae of A. lucorum. Altogether, 69708 target genes related to biogenesis, membrane and binding activities were predicted for 399 miRNAs. Particularly, 15 miRNAs were found to target 16 olfactory genes. These miRNAs could be involved in regulation of olfactory-associated genes ex-pression. Comparing the antennae of nymphs, adult males and females, 94 miRNAs were found to be differentially expressed. The expression levels of some differentially expressed miRNAs measured by qPCR were consistent with sequencing results. This study provides a global miRNAs transcriptome in the antennae of A. lucorum and valuable information for further investigation on miRNA-mRNA interactions, especially the functions of miRNAs in regulating chemosensation.

The human serotonin transporter (hSERT) terminates neurotransmission by removing serotonin from the synaptic cleft, which is an essential process plays an important role in depression. In addition to substrate serotonin, hSERT is also the target of drugs of abuse like cocaine and clinically used antidepressants such as escitalopram and paroxetine. To date, few studies attempt to investigate the unbinding mechanism underlying the orthosteric and allosteric modulation of hSERT. The high-resolution X-ray structure of hSERT resolved recently enables us to theoretically study the unbinding of the above four ligands against the S1 or S2 site of hSERT, by means of molecular docking, molecular dynamics (MD) and potential of mean force (PMF) simulations. We proved that for either the S1 or S2 site, the other three ligands (cocaine, escitalopram and paroxetine) are much more favorable than the original substrate serotonin, whether in kinetics along the unbinding pathways or in thermodynamics at the equilibrium states. Furthermore, the S1 site is much more favorable than the S2 site, for each ligand. Interestingly, inspection revealed that there are ~ 3Å lengths between the allosteric site of serotonin and cocaine, and an unseen un-binding pathway for escitalopram at the S1 site except for verification of the broadest trail.

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

We show that the accelerating expansion phase of the universe can emerge from the group field theory formalism, a candidate theory of quantum gravity. The cosmological evolution can be extracted from condensate states using mean field approximation, in a form of modified FLRW equations. By introducing an effective equation of state w, we can reveal the relevant features of the evolution, and show that with proper choice of parameters, w will approach to −1, corresponds to the behaviour of cosmological constant, results in a late time acceleration and leads to de Sitter spacetime asymptotically.

Water area segmentation in remote sensing is of great importance for flood monitoring. To overcome some challenges in this task, we construct the Water Index and Polarization Information (WIPI) multi-modality dataset and propose a multi-Modality Fusion and Gated multi-Filter U-Net (MFGF-UNet) convolutional neural network. The WIPI dataset enhances the water information and reduces the data dimension. In particular, the Cloud-Free label provided in the database effectively mitigates the issue of scarcity of labeled samples Since a single form or uniform kernel size cannot handle the variety in size and shape of water bodies, we proposed the gated multi-filter inception (GMF-Inception) module in our MFGF-UNet. Moreover, we utilize the attention mechanism by introducing the Gated Channel Transform (GCT) skip connection and integrating GCT into GMF- Inception to further improve model performance. Extensive experiments on three benchmarks, including WIPI, Chengdu and GF2020 datasets demonstrate that our method achieves favorable performance with lower complexity and better robustness against six competing approaches. For example, on WIPI, Chengdu and GF2020 datasets, the proposed MFGF-UNet model achieves F1 of 0.9191, 0.7410, and 0.8421, respectively, which average F1 on three datasets is 0.0045 higher than the U-Net model and reduces 62% average GFLOPs. New WIPI dataset, code and trained models have been released on GitHub

Monascus pigments (MPs) have been used as food colorants for several centuries in Asian countries and nowadays in the whole world via Asian catering. The MPs biosynthetic pathway has been well-illustrated, however, the functions of a few genes including mrpigH in the MPs gene cluster of M. ruber M7 are still unclear. In current study, mrpigH was disrupted in Δmrlig4ΔmrpyrG, a highly efficient gene modification system, using mrpyrG as a selection marker, and ΔmrpigHΔmrlig4ΔmrpyrG::mrpyrG and ΔmrpigHΔmrlig4ΔmrpyrG have been obtained. Subsequently, their morphologies, biomasses, MPs and citrinin (CIT) production were analyzed, respectively. These results have revealed that the deletion of mrpigH has significant effects on the morphology and growth of M. ruber M7. Moreover, compared with M. ruber M7, the yields of MPs and CIT were drastically increased and decreased in mrpigH mutants, respectively.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

This study investigated the efficacy of carvone, abscisic acid (ABA), gibberellin (GA3), and variable temperature in managing dormancy and sprouting in aeroponically grown mini-tuber potato seeds. Results showed that carvone treatment effectively reduced weight loss rate by 12.25% and decay rate by 3.33% at day 25, compared to control. ABA treatment significantly enhanced germination rate to 97.33%. GA3 treatment resulted in the longest sprouts of 14.24 mm and reduced MDA content by 23.08% at day 30, indicating its potential in shortening dormancy and maintaining membrane integrity. Variable temperature treatment showcased a balanced performance in reducing weight loss and maintaining a lower relative conductivity, indicating less cellular damage. Enzymatic activities of α-amylase, CAT, and SOD were modulated by the treatments, ensuring a balanced enzymatic environment for seed vitality. These findings provide a robust foundation for refining post-harvest management strategies to optimize germination uniformity and preserve the quality of aeroponic potato seeds during extended dormancy, promising enhanced yield and productivity in potato cultivation.

The growing interest in fair AI development is evident. The ''Leave No One Behind'' initiative urges us to address multiple and intersecting forms of inequality in accessing services, resources, and opportunities, emphasising the significance of fairness in AI. This is particularly relevant as an increasing number of AI tools are applied to decision-making processes, such as resource allocation and service scheme development, across various sectors such as health, energy, and housing. Therefore, exploring joint inequalities in these sectors is significant and valuable for thoroughly understanding overall inequality and unfairness. This research introduces an innovative approach to quantify cross-sectoral intersecting discrepancies among user-defined groups using latent class analysis. These discrepancies can be used to approximate inequality and provide valuable insights to fairness issues. We validate our approach using both proprietary and public datasets, including EVENS and Census 2021 (England \& Wales) datasets, to examine cross-sectoral intersecting discrepancies among different ethnic groups. We also verify the reliability of the quantified discrepancy by conducting a correlation analysis with a government public metric. Our findings reveal significant discrepancies between minority ethnic groups, highlighting the need for targeted interventions in real-world AI applications. Additionally, we demonstrate how the proposed approach can be used to provide insights into the fairness of machine learning.

The monocular structured light measurement system has low cost, simple algorithms, and a wide measurement range, making it widely applicable in multiple fields. However, in practical applications, the system may be affected by various factors including noise, non-linear intensity, changes in the reflectivity of the object being measured, and the calibration method and accuracy of the system, thereby reducing the measurement accuracy. In order to solve these issues, this paper proposes a new monocular structured light measurement method, mainly comprises the following two points: (a) A denoising algorithm for phase images based on DAE is proposed, which calculates the wrapped phase of the phase-shifted fringes after initial denoising by DAE. Then, a new phase-shifted fringe pattern is generated and input into DAE for iterative denoising, achieving high-performance image denoising and high-precision wrapped phase solution. (b) A new absolute phase height calibration algorithm is proposed, which introduces camera internal and external parameters and uses a two-layer feedforward network to directly establish the relationship between phase and the 3D coordinate system. Without the need for high-precision motion platforms, high-precision phase height calibration is attainable. In general, compared to conventional methods, the experimental results indicate the effectiveness of the proposed method for low-quality phase-shifted fringe 3D reconstruction. In addition, the measurement method described in this article also demonstrates effectiveness in high-dynamic scenes.

Thrombosis has threatened human health in past decades. Bacillus nattokinase is a potential thrombolytic drug without side-effect and low cost and has been introduced into the consumer market as a functional food or dietary supplement. This review firstly summarizes the biodiversity sources and fermentation process of nattokinase, and systematically expounds the structure, cata-lytic mechanism and enzymatic properties of nattokinase; In view of the problems of low fermen-tation yield, insufficient activity and stability of nattokinase, this review discusses the heterologous expression of nattokinase in different microbial hosts, and summarizes the protein and genetic en-gineering progress of nattokinase-producing strains; Finally, this review summarizes the clinical application of nattokinase.

We report on the role of synergistic polarization of Ba0.9Sr0.1TiO3 (BST) nanoparticles in sulfur cathodes to enhance the redox kinetics of polysulfides for high-capacity Li-S batteries. Ferroelectric nanoparticles are known to significantly improve the electrochemical performance of Li-S batteries due to their inherent self-polarization and high adsorption capacity towards polysulfides. X-ray diffraction spectra confirmed the tetragonal symmetry (c/a=1.0073), while Raman spectroscopic analysis validated the presence of tetragonal orientation Raman modes in BST-modified composites. Scanning electron microscope (SEM) images showed a homogeneous distribution of BST in the sulfur cathode system, with grain sizes ranging from 1 to 1.5 μm. Notably, the BST-coupled S50BST30CB10PVDF10 composite cathode achieved a capacity of approximately 820 mAh/g at 100 mA/g, maintaining stability over 100 cycles, demonstrating improved electrochemical performance. Two distinct plateaus between 2.3 V to 2.0 V and 2.0 V to 1.5 V further underscore the superior performance of BST ferroelectric nanoparticles in enhancing the redox kinetics of Li-S batteries. By leveraging the favourable affinity of polar substances towards polysulfides, we aimed to create a more stable reactive environment within the cathodic site, effectively trapping polysulfide intermediates through the synergistic polarization of BST nanoparticles. The synergistic polarization induced by the asymmetric crystal structure of ferroelectrics is anticipated to generate internal electric fields, enhancing chemisorption with heteropolar reactive. The observed high cyclic stability further validates the efficacy of these composite cathodes in mitigating the polysulfide shuttle effect, offering promising prospects for advancing Li-S battery technology.

Purpose The objective of this study was to eliminate any ambiguity by examining the correlation between gut microbiota and both AMD and glaucoma. Methods Mendelian randomization studies were conducted utilizing the data sourced from the GWAS database for the gut microbiome, AMD, and glaucoma. SNP estimates were summarized through five MR methods. We utilized Cochran's Q statistic to evaluate the heterogeneity of the instrumental variables. Additionally, we employed a "leave-one-out" approach to verify the stability of our findings. Results IVW suggests that Eubacterium (oxidoreducens group) and Parabacteroides had a protective effect on AMD. Both weighted median and IVW suggests that Lachnospiraceae (NK4A136 group) and Ruminococcaceae (UCG009) had a protective effect on AMD. However, both weighted median and IVW suggests that Dorea had a risk effect on AMD. Similarly, The IVW of Eubacterium (ventriosum group) showed a risk effect on AMD. The weighted median of Eubacterium (nodatum group), Lachnospiraceae (NC2004 group), and Roseburia had a risk effect on glaucoma. IVW suggested that Ruminococcaceae (UCG004) had a risk effect on glaucoma. Reverse MR analysis found a causal link between Eubacterium (nodatum group) and glaucoma. No causal relationships were found between AMD or glaucoma and the other mentioned bacterial groups. No significant heterogeneity or evidence of horizontal pleiotropy was detected. Conclusions This study found that certain gut bacteria had protective effects on AMD, while others may be risk factors for AMD or glaucoma. Besides, reverse MR found that glaucoma led to increased abundance of certain gut bacteria. Further trials are needed to clarify the specific mechanisms involved.

In the context of the new crown epidemic, remote physical training will already be in order under the guidance of the Ministry of Education. There is a global focus on current lifestyle behaviors and the future health and well-being of youth. Youth physical activity, aerobic activity and muscle fitness levels are declining.[1] Research on the effects of youth physical training and group attitudes is still in its infancy. This study conducted in-depth interviews with online physical training students, parents, teachers involved in the construction of online physical training, and sports practitioners through interview methods, documentation, and mathematical statistics. The results of the interviews were qualitatively coded using NVivo to summarize the attitudes of different subjects toward physical fitness training and the influencing factors, (1) students were basically satisfied with the teaching effect of online physical fitness training (2) parents thought the teaching effect of online physical fitness training was average (3) physical education teachers thought the effect of online physical fitness training was average (4) physical education practitioners thought the effect of online teaching was poor.

Biological micro-dissection has a wide range of applications in the field of molecular pathology. The current laser-assisted dissection technology is expensive, and laser radiation can lead to sample contamination. As an economical and pollution-free micro-dissection method, piezoelectric ultrasonic micro-dissection has a wide application prospect. However, the performance of the current piezoelectric ultrasonic micro-dissection technology is unsatisfactory. In this paper, a novel piezoelectric ultrasonic micro-dissection device based on a flexure mechanism is proposed in order to solve the problems of low dissecting precision and excessive wear of the dissecting needle caused by the harmful lateral vibration of the current piezoelectric ultrasonic micro-dissection device. By analyzing the flexibility of flexure hinge, the type of flexure beam and the optimal design parameters are determined. Through comparing the harmonic response simulation analysis of the micro-dissection device based on a flexure mechanism and the traditional micro-dissection device without the flexure mechanism, the newly designed micro-dissection device achieves the best vibration effect when the driving frequency is 28kHz, compared with the traditional micro-dissection device, the lateral vibration suppression effect is improved by 68%. Then, based on the 3D printing technology, a prototype of a novel micro-dissection device was produced, and its performance was tested. It was found that the flexure mechanism did indeed suppress the lateral vibration of the needle tip. Finally, the experiments of 5μm thick paraffin-embedded rat liver sections were carried out, and the effects of different dissecting parameters on the dissecting effect were analyzed, and the optimal dissecting parameters were obtained. By comparing the dissecting effects of the tissue sample and the wear condition of the needle tip between the novel micro-dissection device and the traditional micro-dissection device under their optimal dissecting parameters, it is proved that the suppression of harmful lateral vibration not only significantly improves the dissecting effect, but also improves the service life and durability of the dissecting needle, which is beneficial to reduce the equipment costs.

Background: Micronutrients has roles in strengthening and maintaining immune function, but its supplementation and/or deficiency effects on respiratory tract infections are inconclusive. This review aims to systematically assess the associations between micronutrient supplementation or deficiency, with novel coronavirus incidence and disease severity. Methods: Systematic literature searches conducted in 5 electronic databases identified 751 unique studies, of which 33 studies (5 supplementation studies, 1 supplementation and deficiency study, and 27 deficiency studies) were eventually included in this review. Proportions of incidence and severity outcomes in each group, and adjusted summary statistics with their relevant 95% confidence intervaIs (CI) were extracted. Data from 19 studies were pooled in meta-analysis using the generic inverse variance method. Findings: A total of 360,346 patients across 16 countries, with a mean age between 32 and 87.7 years, were involved across 33 studies. All studies were on COVID-19 infections. In individuals without micronutrient deficiency, there was a significant reduction on odds of COVID-19 incidence (pooled OR: 0.37, 95% CI: 0.18, 0.78), and ICU admissions or severe/critical disease onset (pooled OR: 0.26, 95% CI: 0.08, 0.89). Insignificant protective effects were observed on other outcome measures – mortality, ICU admission, progression to respiratory-related complications, severe/critical disease onset or requiring respiratory support and hospitalization rate. Conclusion: The absence of micronutrient deficiency significantly reduced COVID-19 incidence and clinical deterioration in hospitalized patients. Usage of micronutrients as prophylaxis and complementary supplement in therapeutic management of COVID-19 patients may be a promising and cost-effective approach warranting in-depth investigation.

The sustainable development of mines has been the focus of attention in recent years, in China, there are a large number of untreated mined-out areas, and a series of disasters caused by instability of the goaf will bring heavy blows to people’s safety and financial resources. Mined-out areas management is an important part that cannot be ignored in mine sustainable development, and filling management is one of the most effective ways to solve the hidden danger of mined-out areas. Among them, cemented filling with tailings and the ultra-high-water backfilling are commonly used in mining enterprises. However, filling treatment will lead to increasing cost and the decreasing profits, which seriously depresses the motivation of mining enterprises and even leads to mor-al hazard. Therefore, the analysis of the economic benefits of goaf control plays a vital role in the sustainable construction and long-term development of mines. This paper proposed the mine-out area treatment economic model, the proposed method employs the guiding philosophy of news-boy model to create a mathematical economy model that provides the basis of goaf management mode for mine. The following research results are achieved: (1) The economic model of mined-out area backfilling treatment is constructed, and which is classified three different modes. (2) Com-bined with mathematical derivation and simulation, the influence of relevant variable parameters on each type of filling mode is discussed. (3) Various types of goaf filling treatment mode are com-pared with non-filling scheme (benchmark mode), so as to provide theoretical support for mining enterprises to choose the appropriate filling scheme. The results shows that the economic model of mined-out area management provides the optimal mode for mined-out area filling, the balance of tailings and ultra-high water filling materials procurement is realized, to making maximum profits. In this paper, the use of economic thinking has an important impact on the sustainable development of safety goaf management. To evaluate the sustainable development of goaf management by building economic models. It has important theoretical basis and practical guiding significance for the development and exploration of mined-out area management by combining economy with sustainable development.

We report that ethanol, used together with water, plays a crucial role in tuning the structures of a zirconium-based Metal-Organic Framework, the 12-connected MOF-801, and the possible mechanisms of this modulating effect. By employing the cosolvent system of ethanol and water just under room temperature without the presence of a monotopic carboxylic acid as the modulator, MOF-801 in various morphologies of different sizes can be synthesized. The linear correlation between the ethanol/water ratio and the crystal sizes is also demonstrated. The growth mechanism is mainly explained by ethanol’s binding with the metal ion clusters and the Marangoni Flow Effect. Ethanol competes with the linker molecules in coordinating with the Zr metal clusters, a role similar to that of the modulators. The Marangoni Flow Effect, which dominates at a certain solvent ratio, further promotes the 1-D alignment of the MOF-801 crystals.

Both in lung adenocarcinoma (LUAD) and severe acute respiratory syndromes (SARS) uncontrolled inflammation could be detected in lung tissue. Whether the similarity mechanism exists is still unknown. PDZ-binding motif (PBM) in SARS-CoV E protein has been demonstrated as virulence factor induce inflammation storm. Study function of PBM in LUAD is significant for mechanism exploration of carcinogenesis mediated by SARS-CoV. To identify gene expression fluctuation induced by PBM, a microarray sequencing data of lung tissue infected by wild type (SARS-CoV-E-wt) and recombinant virus (SARS-CoV-E-mutPBM) was analysis followed by functional enrichment analysis. To understand the role of screened specific genes in LUAD, overall survival and immune correlation were calculated. A total of 12 genes (MAPK1, PRKCA, FGFR4, KDR, PTPRD, BCL2L15, UBD, MAMDC2, LTBP4, PTPRB, LGI3 and ITGA8) might participate in initial and development stage of LUAD through expression variation and mutation. Meanwhile, a total of 12 genes (CARHSP1, EIF4E2, HMGA1, IL1R2, MAGOHB, PVR, ADCY9, ELF5, ESYT3, SCML4, SECL14L4 and THRA) could lead to poorer prognosis via dysregulation. In addition, MAMDC2 and ITGA8 down-regulated by PBM could also alter prognosis. Though the conservative PBM (-D-L-L-V-) could be found at the end of carboxyl terminal in multi E proteins of coronaviruses, the specific function of each one depend on the whole amino acid sequence simultaneously. In conclusion, PBM of SARS-CoV E protein could promote carcinogenesis of LUAD by dysregulating important gene expression profiles followed by influence immune response and overall prognosis. The results in present study also provided reference for the therapy of SARS-CoV-2 in LUAD patients.

Since matter, energy and information are the three major components of the world, is there an interaction between information and matter? In the present work, the coevolution of human language and brain is taken as a case of interaction between information and brain. Some evidence that may show interactions between human language and brain revealed by previous researches is summarized in this paper, such as the language areas in the cerebral cortex of the modern human brain, the evolution of human language and brain in human history, and the genetic basis for the evolution of language. Based on the evidence, a dynamic model is developed to investigate the possible mechanism of coevolution of human language and brain. In the model, human language development and brain development reinforce each other: the developmental level of language can be promoted by advances in brain function due to language-related gene mutations, in turn, whether such mutations are selected positively can be influenced by the current developmental level of language. The coevolution of human language and brain can be taken as a case of interaction between information and matter.

Image encryption is increasingly becoming an important area of research in information security and network communications, as digital images are widely used in various applications and are vulnerable to various types of attacks. In this research work, a color image cryptosystem that is based on a 3-layer permutation-substitution network (PSN) is proposed. For every layer, an encryption key and an S-box are generated and utilized. Those are based on a four-dimensional (4D) dynamical Chen system of a fractional-order, the Mersenne Twister, OpenSLL, Rule 30 Cellular Automata and Intel’s MKL. The sequential application of Shannon’s ideas of diffusion and confusion for 3 times guarantees a total distortion of any input plain image, resulting in a totally encrypted one. Apart from the excellent and comparable performance to counterpart algorithms from the literature, showcasing resistance to visual, statistical, entropy, differential, known plaintext and brute-force attacks, the proposed image cryptosystem provides an exceptionally superior performance in 2 aspects: a vast key space of 2^1658 and an average encryption rate of 3.34 Mbps. Furthermore, the proposed image cryptosystem is shown to successfully pass all the tests of the NIST SP 800 suite.

A recent study found that a 3ppb increase in O₃ ambient concentration was associated with an increased progression of 0.18 percentage points in percent emphysema and that such increase was equal to smoking 20 cigarettes per day for 29 years. A simple estimation of population attributable fraction shows that COPD diagnoses due to smoking are actually 30 times more than those attributed to a 3 ppb increment in O₃ concentration. Labelling ozone pollution as the new smoking may distort perception of the risks and hinder proper response to real life threatening risk such as smoking.

Mobile inspections conducted by intelligent tunnel robots are instrumental in broadening the inspection reach, economizing on inspection expenditures, and augmenting the operational efficiency of inspections. Despite differences from fixed surveillance, mobile-captured traffic videos have complex backgrounds and device conditions that interfere with accurate traffic event identification, warranting more research. This paper proposes an improved algorithm based on YOLOv9 and DeepSORT for intelligent event detection in edge computing mobile device using the intelligent tunnel robot. The enhancements comprise the integration of the Temporal Shift Module to boost temporal feature recognition and the establishment of logical rules for identifying diverse traffic incidents in mobile video imagery. Experimental results show that our fused algorithm achieves a 93.25% accuracy rate, an inprovement of 1.75% over the baseline. The algorithm is also applicable to inspection vehicles, drones, and autonomous vehicles, effectively enhancing the detection of traffic events and improving traffic safety.

For screening excellent lactic acid bacteria (LAB) strains to inhibit Escherichia (E.) coli (ETEC) K88, inhibitory activities of more than 1100 LAB strains isolated from different materials and kept in the lab were evaluated in this study. Nine strains with inhibition zone at least 22.00 mm (including that of hole puncher 10.00 mm) and good physiological and biochemical characteristics identified by 16S DNA gene sequencing and recA gene multiple detection, were assigned to Lactobacillus (L.) plantarum subsp. plantarum (5), L. fermentum (1), L. reuteri (1), W. cibaria (1) and E. faecalis (1), respectively. As investigated for their tolerance abilities and safety, only strain ZA3 possessed high hydrophobicity and auto-aggregation abilities, had high survival rate in low pH, bile salt environment and GI fluids, sensitive to ampicillin, resistant to norfloxacin and amikacin, without hemolytic activity and didn’t carry antibiotic resistance genes, exhibited broad spectrum activity against a wide range of microorganisms, and antibacterial substance may attribute to organic acids, especially lactic acid and acetic acid. The results indicated that the selected strain L. plantarum subsp. plantarum ZA3 could be considered a potential probiotic to inhibit ETEC K88 for further research.

Insulin-like Growth Factor 2 mRNA binding Protein 1 (IGF2BP1) is a promising candidate gene for influencing economic traits in livestock and poultry. The second intronic region of IGF2BP1 is closely related to growth traits, although the exact mechanism remains unclear. The preliminary resequencing results of goats in our laboratory demonstrated that the IGF2BP1 gene region was subject to strong selection, then we selected multiple single nucleotide polymorphisms (SNPs) to identify. Seven SNPs were located in the conserved region of the second intron, and their functions and relationship with growth traits require further clarification. This study selected 348 Nanjiang Yellow goats as experimental subjects, and chose Time of Flight Mass Spectrometer (MALDI-TOF) as the main method. Our results showed that six SNPs were significantly correlated with the growth traits of the Nanjiang yellow goat by association analysis. Among them, the rs652062749(A>G) was identified as the primary locus affecting the later stage of growth traits of Nanjiang yellow goat. Moreover, there was a strong linkage among three SNPs, and the rs638185407 (T>A) mutant type was observed to increase the luciferase activity in H293T cells extremely significantly. The TTAACT, TTCCCC, and ATCACT combination genotypes were dominant combination genotypes, which provided theoretical references for further genetic co-breeding. The results of our study demonstrate the potential role of the IGF2BP1 gene as a functional genetic marker in the breeding programs of Nanjiang Yellow goats.

The combination of new-generation information technology and manufacturing technology has resulted in major and profound impact on future development paradigm of manufacturing. It is challenging for existing methods to conduct a multidimensional trend exploration related to machine tool domain, which is the basis of virtually everything in manufacturing. In this paper, we proposed an integrating approach framework combined topic models, bibliometric, trend analysis and patent analysis to mine insightful information about future development from multi-source data related to machine tool, such as papers, grants, patents and news. Specifically, papers and grants provided two different perspectives to explore the current focuses and future trends in machine tool research. Furthermore, the future technology development of machine tool was investigated through patents analysis. Finally, news related to machine tool industry in recent years was analyzed to analyze future machine tool business mode. The integration of the above various analytical methods and the multi-dimensional mining of literatures enabled the analysis of the future development of machine tool domain systematically from multi-perspectives which include research, technology development and industry. The conclusions obtained in this paper is beneficial to different communities of machine tool in terms of determining the research directions for researchers, identifying industry opportunities for corporations and developing reasonable industry policy for policy makers.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

This study employed a TSMC 0.18-µm 50 V process to establish a high-voltage n-LDMOS structure. In the reference device, the number of floating-poly (poly-2) turns was 7, and the width and spacing of each turn was 1 µm. Although increasing the number of turns reduces the peak field, directly reducing or increasing the number of poly-2 turns is a common practice. The present experiment was realized in three steps, namely fixing the number of occupied area adjustment turns, adjusting the width of each turn, and adjusting the distance between turns. The first step was fixing the number of occupied area adjustment turns. The number of turns was increased from 7 to 9, and the number of turns was reduced to 5 and 3 in the reference group. A reduction in the number of turns led to a greater decrease in the peak field and increase in the breakdown voltage despite the area remaining unchanged. A comparison of the use of three turns with that of seven turns revealed that the maximum electric field decreased by 42%, from 4.17e+3 to 2.46e+3 V/cm, and that the breakdown voltage (VBK) increased from 30.2 to 35.84 V. The second step was adjusting the width of each turn from 1 to 1.4, 1.2, 0.8, and 0.6 µm in the reference group. This increase in width reduced the maximum electric field and led to a greater increase in VBK. When the width was increased to 1.4 µm, the maximum electric field decreased by 29% from 1.95e+3 to 1.4e+3 V/cm, and the VBK increased by 183% from 30.2 to 85.6 V. The third step was adjusting the spacing of each turn from 1 to 1.4, 1.2, 0.8, and 0.6 µm in the reference group. The results revealed that a reduction in the spacing led to a greater reduction in the maximum electric field and an in-crease in the VBK. When the pitch was reduced to 0.6 µm, the maximum electric field decreased by 33%, from 1.95e+3 to 1.32e+3 V/cm, and the VBK increased by 345%, from 30.2 to 134.4 V.

For earthquakes (M4.0) occurring along and arond the East Anatolian fault zone and the the Dead Sea fault zone between January 2002 and December 2022, we analyzed the correlation between the Earth's rotation and the earthquake occurrence before the Mw7.8 Gaziantep,Turkey earthquake occurring on 6 February 2023. We statistically evaluate the Earth's rotationally dependent seismicity. The results were judged by the P-value. There was a clear downward trend in the P-values from early 2020 to late 2022 in the study region. Starting in early 2021, the P-value drops below 0.1%, corresponding significant correlation between the Earth's rotation and the earthquake occurrence . We also calculated the spatial distribution of the P-values and obtained a result showing a low P-value area in the vicinity of the northeastern end of the aftershock zone. Although the stress caused by the Earth's rotation is very weak, when the focal medium is loaded to the critical state to release a large earthquake, the stress due to the Earth's rotation could control the earthauqke occurrence. Therefore, the lower P-values obtained in this study indicates the Earth's rotation-related seismicity prior to the Mw 7.8 Turkey earthquake and could be considered as its precursor.

Indoor scene recognition has great significance for intelligent applications such as mobile robots, location-based services (LBS) and so on. Wherever we are or whatever we do, we are under a specific scene. The human brain can easily discern a scene with a quick glance. However, for a machine to achieve this purpose, on one hand, it often requires plenty of well-annotated data which is time-consuming and labor-intensive. On the other hand, it is hard to learn effective visual representations due to large intra-category variation and inter-categories similarity of indoor scenes. To solve these problems, in this paper, we adopted an unsupervised visual representation learning method which can learn from unlabeled data with a Siamese Convolutional Neural Network (Siamese ConvNet) and graph-based constraints. Specifically, we first mined relationships between unlabeled samples with a graph structure. And then, these relationships can be used as supervision for representation learning with a Siamese network. In this method, firstly, a k-NN graph would be constructed by taking each image as a node in the graph and its k nearest neighbors are linked to form the edges. Then, with this graph, cycle consistency and geodesic distance would be considered as criteria for positive and negative pairs mining respectively. In other words, by detecting cycles in the graph, images with large differences but in the same cycle can be considered as same category (positive pairs). By computing geodesic distance instead of Euclidean distance from one node to another, two nodes with large geodesic distance can be regarded as in different categories (negative pairs). After that, visual representations of indoor scenes can be learned by a Siamese network in an unsupervised manner with the mined pairs as inputs. In order to evaluate the proposed method, we tested it on two scene-centric datasets, MIT67 and Places365. Experiments with different number of categories have been conducted to excavate the potential of proposed method. The results demonstrated that semantic visual representations for indoor scenes can be learned in this unsupervised manner. In addition, with the learned visual representations, indoor scene recognition models trained with the learned representations and a few of labeled samples can achieve competitive performance compared to the state-of-the-art approaches.

The biosynthesis of C27-29 sterols from their C30 precursor squalene involves C24-alkylation and removal of three methyl groups, including two at the C4 position. The two C4 demethylation reactions require a bifunctional enzyme known as 3β-hydroxysteroid dehydrogenase/C4-decarboxylase (3βHSD/D) that removes an oxidized methyl (carboxylic) group at C4 while simultaneously catalyzing the 3β-hydroxyl3-keto oxidation. Its loss-of-function mutations cause ergosterol-dependent growth in yeast and congenital hemidysplasia with ichthyosiform erythroderma and limb defect (CHILD) syndrome in humans. Although plant 3βHSD/D enzymes were well studied enzymatically, their developmental functions remain unknown. Here we employed a CRISPR/Cas9-based genome-editing approach to generate knockout mutants for two Arabidopsis 3βHSD/D genes, HSD1 and HSD2, and discovered the male gametophytic lethality for the hsd1 hsd2 double mutation. Pollen-specific expression of HSD2 in the heterozygous hsd1 hsd2/+ mutant not only rescued the pollen lethality but also revealed critical roles of the two HSD genes in embryogenesis. Our study thus demonstrated essential functions of the two Arabidopsis 3βHSD/D genes in male gametogenesis and embryogenesis.

Recently deep cross-modal hashing networks have received increasing interests due to its superior query efficiency and low storage cost. However, most of existing methods concentrate less on hash representations learning part, which means the semantic information of data cannot be fully used. Furthermore, they may neglect the high-ranking relevance and consistency of hash codes. To solve these problems, we propose a Self-Attention and Adversary Guided Hashing Network (SAAGHN). Specifically, it employs self-attention mechanism in hash representations learning part to extract rich semantic relevance information. Meanwhile, in order to keep invariability of hash codes, adversarial learning is adopted in the hash codes learning part. In addition, to generate higher-ranking hash codes and avoid local minima early, a new batch semi-hard cosine triplet loss and a cosine quantization loss are proposed. Extensive experiments on two benchmark datasets have shown that SAAGHN outperforms other baselines and achieves the state-of-the-art performance.

Despite the considerable focus on job characteristics and individual differences in job crafting research, the influence of social factors on job crafting has not been well-acknowledged. This meta-analysis estimates the associations between social factors and job crafting, and how social factors contribute to employee outcomes through their job crafting. Based on a sample of 51 empirical studies that included 54 independent effect sizes (N = 17,863), we found that social factors of positive leadership styles (e.g., empowering and transformational) and coworker support were positively related to employee job crafting. Further, our study showed that employee job crafting positively mediate the relationships between social factors and work outcomes (e.g., job performance and well-being). Our study contributes to job crafting literature by integrating social factors into the job crafting model and demonstrating that the social context of work (in particular organizational-insiders) play a crucial role in shaping employees’ job crafting behavior. We also emphasize the critical role that job crafting plays in transmitting valuable social resources into improved work outcomes. Building on our results, we provide future direction for job crafting research and discuss how our results can imply practice in terms of job crafting training.

We fabricated high-quality MAPbBr3 single crystals (SC) by introducing moderate amount electron-rich poly(propylene glycol bis(2-aminopropyl ether) (PEA) additives with an inverse temperature crystallization (ITC) method. The intramolecular vibrations and defective states of prepared MAPbBr3 single crystals were systemically studied by the in situ variable-temperature Fourier Transform Infrared (FTIR) Spectroscopy, X-ray photoelectron spectroscopy (XPS), and the synchrotron-based X-ray absorption near edge structure (XANES), et al. We infer that the proper amount of PEA additives would prevent the formation of intermediate states and crystal boundaries, passivating the density of defective states. The X-ray detection properties of single-crystal MAPbBr3 crystals were investigated, using both high dose and low dose X-ray photons at 40keV in synchrotron beamlines. The photocurrent of optimized PEA-treated MAPbBr3 single crystals demonstrate better performance compared with the as-prepared single crystals. Meanwhile, the decay time of MAPbBr3 single crystal is decreased from 460 ns to 210 ns by Time-resolved photoluminescence (TRPL) decay measurement, owing to the defect passivation by 0.5wt% PEA additives. The PEA-treated single crystals possess much faster decay time than the commercialized Ce:YAG scintillator (>500ns). These results help elucidate the passivation of defective states and contribute paths to manufacture high-quality single crystal perovskites for next-generation optoelectronic devices.

The separation and enrichment can be targeted to enrich the rare and precious metals in fly ash and reduce the cost of leaching and recovering of fly ash. Regarding their different properties, the single-component separation was used to obtain uncompleted burned carbon, glass microbeads, minerals, and other characteristic components from the ash. Also, the mineral composition of each component was analyzed by electron microscopy. The metal minerals were mainly concentrated in the mineral components. Besides, the electron probe micro-analysis shows that the Pt content in the minerals of fly ash was significantly correlated with the metal contents of Ni and Cu. After the obtainment of the characteristics of fly ash metal enrichment, the heavy minerals with Cu, Ni, Pt, Pd, and other target metal elements were enriched by gravity separation and flotation. The enrichment coefficients of Cu, Ni, Pt, and Pd were 1.45, 1.33, 1.90 and 1.60, respectively, and the recovery rates were 77%, 81%, 97% and 88% respectively. Since the yield of heavy minerals obtained by separation was 62.24%, it indicated the physical separation method could significantly reduce the cost of leaching and recovering of fly ash metal resources.

To develop green super rice varieties with high and stable yields under the rainfed conditions and improved nutrient use efficiency (NuUE), a modified backcross (BC) breeding approach was adopted using a high yielding and widely adaptable Xian variety, WTR1, as the recipient and a Geng variety, HAN, as the donor. Starting from the BC1F2 generation, the BC population had gone through one generation of selection under the IG, LI and RF conditions, followed by consecutive four generations of screening and selection for high GY under six different nutrient conditions, leading to the development of 230 BC1F6 introgression lines (ILs). The final evaluation of the 230 ILs under the six nutrient conditions identified many ILs with improved yields under various combinations of nutrient deficient conditions, including 12 promising lines that had significantly improved NuUE under two or more nutrient deficiency conditions. Our results demonstrated an efficient inter-subspecific BC breeding procedure with first round selection under the rainfed-drought condition followed by four generations of progeny testing for yield performances under six different nutrient conditions. The promising ILs were studied under replicated yield trials under 75N and -NPK conditions for developing high yield rice varieties with improved NuUE. Our results indicated that NuUE in rice was controlled by complex genetic and physiological mechanisms and the developed ILs provided useful materials for genetic and molecular dissection of NuUE in rice.

To guide the design and optimization of King Grass (KG) harvesting machinery, this paper studied the cutting characteristics of KG stalks under different physical properties and mechanical parameters. A cutting device that can achieve different parameter adjustments was designed, and indoor cutting experiments were conducted. The results of the single factor experiment show that with the increase of moisture content and stalk height, the ultimate shear stress (USS) and unit-area cutting energy consumption (UCEC) gradually decrease. The optimal range of blade clearance for cutting KG stalks is 2.0-4.0 mm. The optimal value range for oblique cutting angle is 10 ° -40 °. The reasonable range of skew cutting angle is 10 °-20 °. The optimal range for sliding cutting angle is 20 ° - 40 °. The response surface methodology was used to conduct parameter optimization experiments. The regression models were established for various factors and the USS, as well as the UCEC. The optimal combination of cutting parameters has been determined. Under this parameter setting, the USS is 0.4 MPa and UCEC is 3.5 mJ/mm2. The average relative errors between the predicted and experimental values of USS and UCEC were 6.34% and 4.71%, respectively. This indicates that the model can correct reflect the mathematical relationship between various factors and USS and UCEC. This study provides theoretical support for the design of KG harvesting machinery.

Prosthetic attack is a problem that must be prevented in the current finger vein recognition application. To solve this problem, a finger vein living detection system was established in this article. The system first captures short-term static finger vein video by uniform near-infrared lighting, segments the veins by Gabor filters with current removing, calculates the multi-Scale spatial-Temporal maps(MSTmap) from the selected vein blocks, and trains the MSTmaps in the proposed Light-ViT network for the liveness detection. The MS maps are used to extract the coarse feature and Light-ViT is used to refine the liveness feature and predict the liveness result. Light-ViT, featuring an enhanced L-ViT backbone as its core, is constructed by interleaving multiple MN blocks and L-ViT blocks. This architecture effectively balances the learning of local image features, controls network parameter complexity, and substantially improves the accuracy of liveness detection. The accuracy of the Light-ViT network is verified to be 99.63% on the self-made living / prosthetic finger vein video dataset. This proposed system can also be directly applied to the finger vein recognition terminal after the model lightweighting.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

The reduction in rheological parameters and dissolution rate of precursors in geopolymer coatings during early hydration significantly contributes to sagging. This study aims to improve the sag resistance of these coatings by incorporating diatomite filler. Rheological testing was conducted to assess the impact of diatomite and its concentration on yield stress, plastic viscosity, and thixotropy of the geopolymer coatings. The results indicated that diatomite's large specific surface area and high reactivity have a significant influence on the rheological parameters and early dissolution rate of precursors. With a diatomite concentration of 1.1%, the coating exhibited a yield stress of 2.749 Pa and a plastic viscosity of 0.921 Pa·s, maintaining stability, homogeneity, and no sagging at a thickness of 600 μm. Furthermore, the highly active SiO2 in diatomite participates in the secondary hydration reaction of the geopolymer materials, leading to the formation of substantial C-(A)-S-H gel. This gel enhances internal interconnectivity within the coating, thereby improving its rheological and mechanical properties.

Traffic sign detection plays a pivotal role in autonomous driving systems. The intricacy of the detection model necessitates high-performance hardware. Real-world traffic environments exhibit considerable variability and diversity, posing challenges for effective feature extraction by the model. Therefore, it is imperative to develop a detection model that is not only highly accurate but also lightweight. In this paper, we proposed YOLO-ADual, a novel lightweight model. Our method leverages the C3Dual and Adown lightweight modules as replacements for CPS and CBL modules in YOLOv5. The Adown module effectively mitigates feature loss during downsampling while reducing computational costs. Meanwhile, C3Dual optimizes the processing power for kernel feature extraction, enhancing computation efficiency while preserving network depth and feature extraction capability. Furthermore, the inclusion of the CBAM module enables the network to focus on salient information within the image, thus augmenting its feature representation capability. Our proposed algorithm achieves a [email protected] of 70.1% while significantly reducing the number of parameters and computational requirements to 51.83% and 64.73% of the original model, respectively. Compared to various lightweight models, our approach demonstrates competitive performance in terms of both computational efficiency and accuracy.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

The demand for precise indoor localization services is steadily increasing. Among various methods, fingerprint-based indoor localization has become a popular choice due to its exceptional accuracy, cost-effectiveness, and ease of implementation. However, its performance degrades significantly as a result of multipath signal attenuation and environmental changes. In this paper, we propose an indoor localization method based on fingerprints using self-attention and long short-term memory (LSTM). By integrating a self-attention mechanism and LSTM network, the proposed method exhibits outstanding positioning accuracy and robustness in diverse experimental environments. The performance of the proposed method is evaluated under two different experimental scenarios, which involve 2D and 3D moving trajectories, respectively. The experimental results demonstrate that our approach achieves an average localization error of 1.76 m and 2.83 m in the respective scenarios, outperforming the existing state-of-the-art methods by 42.67% and 31.64%.

The present study provides a detailed analysis of the chloroplast genome of Microula sikkimensis. The genome was consisted of altogether 149,428bp and distinct regions, including large single-copy (81329bp), small single-copy (17261bp), and inverted repeat (25419bp). The genome contained 112 genes, including 78 protein-coding genes, 30 tRNA genes, and 4 rRNA genes, some exhibited duplication in the IR region. The chloroplast genome displayed different GC content across regions, with the IR region exhibiting the highest. Codon usage analysis and the identification of simple sequence repeats (SSRs) offer valuable genetic markers. Comparative analysis with other Boraginaceae species highlighted conservation and diversity in coding and noncoding regions. Phylogenetic analysis placed M. sikkimensis within the Boraginaceae family, revealing its distinct relationship with specific species.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

Epigallocatechin-3-gallate (EGCG) is the most abundant polyphenol in green tea. In this study, the effects of dietary EGCG on oxidative stress and the metabolism and toxicity of acetaminophen in liver were investigated. Rats were fed the diets with (0.54 %) or without EGCG supplementation for four weeks and were then intraperitoneally injected with acetaminophen (1g/kg). Results showed EGCG lowered hepatic oxidative stress and cytochrome P450 (CYP) 1A2, 2E1, and 3A, and UDP-glucurosyltransferase activities prior to acetaminophen injection. After acetaminophen challenge, the elevations in plasma alanine aminotransferase activity and histological changes in liver were ameliorated by EGCG treatment. EGCG reduced acetaminophen-induced apoptosis by increasing the Bax/Bcl2 ratio in liver. EGCG mildly increased autophagy by increasing the LC3B II/I ratio. Lower hepatic acetaminophen-glutathione and acetaminophen-protein adducts contents were observed after EGCG treatment. EGCG increased glutathione peroxidase and NAD(P)H quinone 1 oxidoreductase activities and reduced organic anion-transporting polypeptides 1a1 expression in liver after acetaminophen treatment. Our results indicate that EGCG may lower oxidative stress and reduce the metabolism and toxicity of acetaminophen. The reductions in CYP-mediated acetaminophen bioactivation and uptake transporter, as well as enhanced antioxidant enzyme activity, may limit the accumulation of toxic products in liver and thus lower hepatotoxicity

To enhance industrial competitiveness and increase productivity, every country has strived to create a smart factory by introducing technologies such as Internet of Things, big data and artificial intelligence into production line and build cyber-physical system for the purpose of promoting manufacturing efficiency. For mission assignment, production line management or manufacturing field analysis, the location information of employee, machine and material is very essential. To promote manufacturing efficiency, of course, the location information became more important. A Bluetooth low energy (BLE) positioning system for the manufacturing is developed in this research. A "Tag tracking" mechanism is addressed and adopted, which uses Beacon to catch the location information and a BLE receiver is also used to receive the broadcasting information from Beacon. The position information from the BLE receiver will be compared with the data in the database for calculating the location of the target. The status of the target may also be obtained by using the data from the BLE receiver. Comparing with the mobile device, this method can reduce energy consumption and make the maintenance simple and easy. In the real applications, the target may not be limited to human. The "Regional label positioning technology" is also investigated in this research. Defining a suitable zone location and arranging BLE receiver location, and positioning analysis theory are the key factors included in this developed technology. The developed system will be tested for real industry applications. The test results show that the feasibility of this technology.

Management of chronic inflammation and wounds has always been a key issue in the pharmaceutical and healthcare sector. Curcumin (CCM) is an active ingredient extracted from turmeric rhizomes that has antioxidant, anti-inflammatory, and antibacterial activities, thus showing significant effectiveness toward wound healing. However, its shortcomings such as poor water solubility, poor chemical stability and fast metabolic rate limit its bioavailability and long-term use. In this context, hydrogels appear to be a versatile matrix for carrying and stabilizing drugs due to the biomimetic structure, soft porous microarchitecture, and pleasant biomechanical properties. The drug loading/releasing efficiencies can also be controlled by use of highly crystalline and porous metal organic frameworks (MOFs). Here, a flexible hydrogel composed of sodium alginate (SA) matrix and CCM-loaded MOFs was constructed for long-term drug release and antibacterial activity. The morphology and physicochemical properties of composite hydrogels were analyzed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), ultraviolet visible spectroscopy (UV-Vis), Raman spectroscopy and mechanical property tests. The results showed that the composite hydrogel was highly twistable and bendable to mechanically comply with human skin. The as-prepared hydrogel could capture efficient CCM for slow drug release as well as effective killing of bacteria. Therefore, such composite hydrogel is expected to provide a new management system for chronic wound dressings.

Sea surface partial pressure of CO2 (pCO2) is a critical parameter in the quantification of air-sea CO2 flux, which plays an important role in calculating the global carbon budget and ocean acidification. In this study, we use chlorophyll-a concentration (Chla), sea surface temperature (SST), absorption due to dissolved and particulate detrital matter (Adg), diffuse attenuation coefficient of downwelling irradiance at 490nm (Kd) and mixed layer depth (MLD) as input data for retrieving the sea surface pCO2 in the North Atlantic based on a remote sensing empirical approach with the Categorical Boosting (CatBoost) algorithm. The results show that the root mean square error (RMSE) is 8.25μatm, the mean bias error (MAE) is 4.92μatm and the coefficient of determination (R2) can reach 0.946 in the validation set, which mean that the CatBoost model makes an improvement compared to other models in the published studies. In the further analysis of the spatial and temporal distribution of the sea surface pCO2 in the North Atlantic, it can be found that the North Atlantic sea surface pCO2 has a clear trend with latitude variations and have strong seasonal changes. Furthermore, the sea surface pCO2 in this area is mainly affected by sea temperature and salinity, and influenced by biological activities in some sub-regions.

As an emerging network paradigm, Space-Air-Ground integrated networks (SAGIN) has attracted the attentions from academia and industry. That is because SAGIN can implement seamless global coverage and connections among electronic devices in space, air, and ground spaces. Additionally, the shortages of computing and storage resources in mobile devices greatly affect the quality of experiences for intelligent applications. Hence, we devise to integrate SAGIN as an abundant resource pool into mobile edge computing environments (MEC). To facilitate efficient processing, we need to solve the optimal task offloading decisions. Different from the existing MEC task offloading solutions, we have to face some new challenges, such as the fluctuation of processing capability for an edge computing node, the uncertainty of the transmission latency caused by the heterogeneous network protocols, the uncertain amount of uploaded tasks during a period, and so on. In this paper, we firstly describe a task offloading decision problem in new challenge environments. But, we cannot use the standard robust optimization and stochastic optimization methods to obtain the optimal result under the uncertain network environments. In this paper, we propose the condition value at risk-aware distributionally robust optimization algorithm, named as CVAR-DRO, to solve the task offloading decision problem. The proposed CVAR-DRO method combines the distributionally robust optimization and the condition value at risk model for solving the optimal result. And then, We have evaluated our approach in simulation SAGIN environments with the confidence interval, the number of mobile task-offloading and the various parameters. We compare our proposed CVAR-DRO algorithm with the state-of-the-art algorithms, such as the standard robust optimization algorithm, the stochastic optimization algorithm, the DRO algorithm, and the brute algorithm. The experimental results show that CVAR-DRO can get a sub-optimal mobile task-offloading decision. Overall, CVAR-DRO is more robust than others to the new challenges mentioned above in SAGIN.

Both lung adenocarcinoma and SARS-CoV-2 infection could cause pulmonary inflammation. Angiotensin-converting enzyme 2, not only as the functional receptor of SARS-CoV-2 but also play key role in lung adenocarcinoma. To study the risk of SARS-CoV-2 infection in lung adenocarcinoma patients, mRNA and miRNA profiles were obtained from TCGA and GEO databases followed by bioinformatics analysis. A regulatory network which regards angiotensin-converting enzyme 2 as the center would be structured. In addition, via immunological analysis about key factors in lung adenocarcinoma patients, to explore the essential reasons for the susceptibility of SARS-CoV-2. Compared with normal tissue, angiotensin-converting enzyme 2 was increased in lung adenocarcinoma patients. Furthermore, a total of 7 differently expressed correlated mRNAs (ACE2, CXCL9, MMP12, IL6, AZU1, FCN3, HYAL1 and IRAK3) and 5 differently expressed correlated miRNAs (miR-125b-5p, miR-9-5p, miR-130b-5p, miR-381-3p and miR-421) were screened followed by enrichment analysis. Interestingly, toll-like receptor signaling pathway with the most frequent occurrence was enriched by mRNA (IL6) and miRNA (miR-125b-5p) sets simultaneously. Finally through comprehensive analysis, it was assumed that miR-125b-5p-ACE2-IL6 axis in the structured regulatory network could alter risk of SARS-CoV-2 infection in lung adenocarcinoma patients.

Biofertilizer, an environment-friendly and renewable plant nutrient source, has been widely applied and studied to reduce dependency on chemical fertilizers. However, most studies focus on the effects of biofertilizer on the bacterial and fungal communities, and we still lack an understanding of biofertilizer on the protistan community. Here, the effects of biofertilizer application on the composition and interaction of the protistan community in the wheat rhizosphere were investigated based on a 4-year field experiment. Biofertilizer application altered soil physicochemical properties and the protistan community composition (ANOSIM, p &lt; 0.001), and significantly induced an alpha diversity decline. Random forecast and redundancy analysis demonstrated that nitrogenase activity and available phosphorus were the main drivers. Trichomonas classified to the phylum Metamonada was enriched by biofertilizer, and was significantly positive connections with soil nitrogenase activity and some function genes involved in nitrogen-fixation and nitrogen-dissimilation. Biofertilization loosely connected biotic interactions, while did not affect the stability of the protistan community. Besides, biofertilizer promoted the connections of protists with fungi, bacteria, and archaea. Combined with the conjunct biotic network (protist, fungi, bacteria, and archaea) and interactions between protists and soil physicochemical properties/function genes, protists may act as keystone taxa potentially driving soil microbiome composition and function.

Psoriasis is a chronic, multisystem, inflammatory disease. The typical clinical cutaneous manifestation of psoriasis is scaly erythema or plaque, limited or widely distributed. However, psoriasis is far beyond the skin involvement and provides many challenges, including associated comorbidities. In this review, we classify psoriasis as cutaneous and systemic psoriasis, according to the clinical diversity and associated comorbid diseases, and recommend classification criteria for psoriasis. The key objective of this novel classification is to raise awareness of the complexity of this multifaceted disease and help to better understand and manage this complex disease comprehensively.

This study investigates the transformative impact of ChatGPT, a cutting-edge AI language model developed by OpenAI, on the financial sector. We explore ChatGPT's applications in financial analysis, focusing on its ability to perform tasks traditionally handled by human analysts. By creating a set of multi-step and advanced reasoning financial tasks, and establishing several task-specific evaluation metrics, our experimental results demonstrate that ChatGPT-4o can effectively perform both basic and some complex financial analysis tasks comparable to those executed by humans. However, our empirical evaluation reveals limitations in its performance on complex tasks that require comprehensive understanding and critical thinking. The study highlights the necessity for meticulous task formulation and robust evaluation to achieve consistent functionality. While ChatGPT enhances efficiency in financial analysis, its integration with human expertise remains crucial for effective decision-making. This study contributes to the understanding of AI's role in finance and provides insights into its potential and constraints, guiding future integration of AI technologies in financial practices.

Disulfiram (DSF), an anti-alcoholism medicine, exerts treatment effects in patients suffering from persistent Borreliosis and also exhibits anti-cancer effects by its copper chelating derivatives. Since chronic/persistent borreliosis is characterized by increased amounts of proinflammatory macrophages, this study investigated opsonin-independent phagocytosis, migration and surface marker expression of in vivo activated human monocyte-derived macrophages and dendritic cells with and without DSF treatment. Phagocytosis of non-opsonized Dynabeads® M-450 and migration of macrophages and dendritic cells were monitored using live cell analyzer Juli™ Br for 24h by imaging every 3.5 min. Results were analyzed by a newly developed software based on the differential phase contrast images of cells before and after ingestion of Dynabeads bearing an electron dense iron core. As a control, phagocytosis was also monitored by visual counting of ingested beads. DSF decreased the phagocytic capacities exhibited by global macrophages and dendritic cells. DSF also impaired the migration of human monocyte-derived macrophages and dendritic cells (hMDMD) and significantly reduced the expression densities of surface antigens CD45 and CD14. In cells consisting of anti-inflammatory M2 macrophages, DSF led to a remarkable cell death and also increased oxidative stress as determined by MitoSox staining. Mitochondrial oxidative stress was a prominent feature in M2 macrophages which were more sensitive to DSF-induced cytotoxicity.

With the development of organizational biology and forced from the EU Cosmetic Regulation (EU/1223/2009) with the complete ban of animal testing for cosmetic purposes, 3D skin models have been widely developed due to their similar physiological structure and metabolic function to native human tissue. 3D skin models for in vitro cosmetic evaluation are still promising alternative methods for evaluating phototoxicity, corrosivity and irritation. These models have been used for early screening and later validation of toxicity and efficacy evaluation by many well-known cosmetic companies. 3D skin models have become an important tool in cosmetic evaluation research. This article reviews the development of 3D skin models and their application in cosmetic evaluation. An outlook on the current application and future technological development directions in the cosmetic field is also presented.

Based on the marine natural products piperafizine B, X334 and our previously reported compound 4m, fourteen novel 3,6-diunsaturated 2,5-diketopiperazine (2,5-DPK) derivatives (1-2, 4-6, 8-16), together with two known ones (3 and 7), were designed and synthesized as anticancer agents against cell lines A549 and Hela. The MTT assay results showed that the derivatives 6, 8-12 and 15 had moderate to good anticancer capacities with the IC50 values ranging from 0.7 to 8.9 μM. Among them, compound 11 with naphthalen-1-ylmethylene and 2-methoxybenzylidene functions at the 3- and 6-positions of 2,5-DPK ring, respectively, displayed good inhibitory activities to both cancer cells A549 (IC50 = 1.2 μM) and Hela (IC50 = 0.7 μM). It could also induce apoptosis and obviously block the cell cycle progression at G2/M phase in both cells at 1.0 μM. The electron withdrawing functions might not be favorable for the derivatives with high anticancer activities. Additionally, compared to piperafizine B and X334, these semi-N-alkylated derivatives have high liposolubilities (&gt; 1.0 mg•mL-1). Compound 11 can be further developed aiming to the discovery of novel anticancer candidate.

For massive multiple-input multiple-output (MIMO) communications, the minimum mean square error (MMSE) scheme provides close to optimal recognition but involves inverting the high-dimensional matrix. A Gauss-Seidel (GS) detector based on conjugate gradient and Jacobi iteration (CJ) joint processing is introduced to address this problem. Firstly, the signal is initialized with the best of the three initialization regimes for faster algorithm convergence. Secondly, the signal is processed together with CJ. Finally, the pre-processed result is transferred to the GS detector. The simulation results indicate that the proposed iterative algorithm has a lower BER performance than the GS and improved iterative scheme based on GS in channels with different correlation levels.

Geologists employ high-spatial-resolution (HR) remote sensing (RS) data for many diverse applications as they effectively reflect detailed geological information, enabling high-quality and efficient geological surveys. Applications of HR RS data to geological and related fields have grown recently. By analyzing these applications, we can better understand the results of previous studies and more effectively use the latest data and methods to efficiently extract key geological information. HR optical remote sensing data are widely used in geological hazard assessment, seismic monitoring, mineral exploitation, glacier monitoring, and mineral information extraction due to high accuracy and clear object features. Compared with optical satellite images, synthetic-aperture radar (SAR) images are stereoscopic and exhibit clear relief, strong performance, and good detection of terrain, landforms, and other information. SAR images have been applied to seismic mechanism research, volcanic monitoring, topographic deformation, and fault analysis. Furthermore, a multi-standard maturity analysis of the geological applications of HR images using literature from the Science Citation Index reveals that optical remote sensing data are superior to radar data for mining, geological disaster, lithologic, and volcanic applications, but inferior for earthquake, glacial, and fault applications. Therefore, geological remote sensing research needs to be truly multidisciplinary or interdisciplinary, ensuring more detailed and efficient surveys through cross-linking with other disciplines. Moreover, the recent application of deep learning technology to remote sensing data extraction has improved automatic processing and data analysis capabilities.

Entrepreneurship has been viewed as an opportunity for economic development and changing economic scenarios in global markets. Women are viewed as a reservoir of entrepreneurial talent, so they can be growth engines in novel markets. Previous studies have considered entrepreneurship as the most effective way towards the economic empowerment of women. Female students engaged in entrepreneurial education have been addressed persistently, while what transforms them in an education process is still unclear. Considering the transforming global economy and its influence on higher education, this study aims to detect female students transforming entrepreneurial competency, mindset, and intention into sustainable entrepreneurship. Using a self-compiled survey, we targeted 752 female students to investigate their entrepreneurial competency, mindset, and intention. SPSS and AMOS were used to transform the data for interpretation. We assumed that the impact of female students’ entrepreneurial competency could be modified by an entrepreneurial mindset and result in entrepreneurial intention. To detect this causal relationship, this study employed reliability, factor, structural equation modeling (SEM), and bootstrap-ping analyses to verify the evidence. The result of the SEM confirms that female students’ entrepreneurial competency will, through their entrepreneurial mindset, impact entrepreneurial intention. With bootstrapping, 5000 samples were collected, and it was demonstrated that the measure constructs were still reliable in the model. This study found that there is a mediation effect between entrepreneurial competency and entrepreneurial intention. The entrepreneurial mindset plays a crucial role in the transformation process. Without an entrepreneurial mindset, entrepreneurial competency cannot exert a significant effect on entrepreneurial intention. The findings can help reinvent related entrepreneurial education in higher education.

Aluminum (Al) toxicity and low phosphorus availability (LP) are the top two co-existing edaphic constraints limiting agriculture productivity in acid soils. Plants have evolved versatile mechanisms to cope with the two stresses alone or simultaneously. However, the specific and common molecular mechanisms, especially those on flavonoids and carbohydrate metabolism, are still unclear. Laboratory studies were conducted on two wheat genotypes, Fielder (Al-tolerant and P-efficient) and Ardito (Al-sensitive and P-inefficient), exposed to 50 μM Al and 2 μM Pi (LP) in hydroponic solutions. After 4 days of stress, wheat roots were analyzed via transcriptomic and targeted metabolomic techniques. A total of 2296 differentially expressed genes (DEGs, 1535 up and 761 down) under Al and 3029 DEGs (1591 up and 1438 down) under LP were identified in Fielder. Similarly, 4404 DEGs (3191 up and 1213 down) under Al and 1430 DEGs (1176 up and 254 down) under LP were identified in Ardito. The GO annotation analysis results that 4079 DEGs annotated to the metabolic processes term. These DEGs were significantly enriched in the phenylpropanoid, flavonoid, flavone and flavonol biosynthesis, and carbohydrate metabolism pathways by performing the KEGG enrichment analysis. The targeted metabolome analysis detected 19 flavonoids and 15 carbohydrate components in Fielder and Ardito under Al and LP. More responsive genes and metabolites were involved in flavonoid metabolism under LP than Al in the Fielder, while an opposite trend in the Ardito. In the carbohydrate metabolism pathway, the genes and metabolites were higher in Fielder than in Ardito. The combined transcriptome and metabolome analysis revealed that the flavonoid and carbohydrate genes and metabolites differed between Fielder and Ardito under Al and LP, which may be an important reason for Fielder’s high Al and LP resistance. The results of this study lay a foundation for pyramiding genes and breeding multi-resistance varieties.

It is time-consuming for acquiring complete data by fully phase encoding in two orthogonal directions along with one frequency encoding direction. Undersampling in the 3D k-space is promising in accelerating such 3D MRI process. Though 3D undersampling can be conducted according to predefined probability density, the density based method is not optimal. Because of the large amount of 3D data and computational cost, it is challenging to perform data-driven and learning-based 3D undersampling and subsequent 3D reconstruction. To tackle this challenge, this paper proposes a deep neural network called EEUR-Net, realized by optimizing specific undersampling patterns for the fully-sampled 3D k-space data. Innovatively, our undersampling algorithm employs an end-to-end deep learning approach to optimize phase encoding patterns and uses a 3D U-Net for image reconstruction of undersampled data. Through end-to-end training, we obtain an optimized 3D undersampling pattern, which significantly enhances the quality of the reconstructed image under the same acceleration factor. A series of experiments on a knee MRI dataset demonstrated that, in comparison to standard random uniform, radial, Poisson and equispaced Cartesian undersampling schemes, our end-to-end learned undersampling pattern considerably improves the reconstruction quality of undersampled MRI images.

Agriculture is an industry that heavily relies on the environment. The increasing frequency of ex-treme disasters attributable to climate change has adversely affected agricultural land and dis-rupted the stability of the supply of agricultural products. Therefore, we implemented a research program focused on current strategies for adapting to agricultural meteorological disasters. The primary goal was to actively promote disaster prevention information and techniques through information platforms and applications and to provide refined forecasting and an early warning system to enhance preparedness for and recovery from agricultural disasters. This initiative can transform passive mitigation into dynamic action by disseminating crucial information to farmers. We integrated meteorological data and crop characteristics to develop disaster prevention strate-gies for the predisaster, during-disaster, and postdisaster stages to empower farmers to implement autonomous disaster prevention, ensuring their profitability and minimizing the impact of disas-ters. This paper presents an agricultural disaster prevention system involving cross-disciplinary collaboration to establish an early warning system for crop disasters. However, the effectiveness of the early warning system relies on the availability of complete meteorological and crop infor-mation, necessitating high-density agricultural meteorological stations, refined weather forecast services, historical crop damage data, and ongoing research and development on disaster preven-tion technology. In the system, a diversified social media interface is used to provide local farmers with weather forecast information. When impending disasters are identified, the platform acti-vates disaster prevention measures to reduce agricultural losses. This article paper introduces Taiwan’s agricultural disaster prevention system as a complete disaster prevention strategy.

The rapid growth of network services, Internet of Things devices and online users on the Internet have led to an increase in the amount of data transmitted daily. As more and more information is stored and transmitted on the Internet, cybercriminals are trying to gain access to the information to achieve their goals, whether it is to sell it on the dark web or for other malicious intent. Through thorough literature study relating to the causes and issues that are brought from the security and privacy segment of wireless networks, it is observed that there are various factors that can cause the networks to be an insecure; especially factors that revolve around cybercriminals with their growing expertise and the lack of preparation and efforts to combat them by relevant bodies. The aim of this paper is to showcase major and frequent security as well as privacy issues in wireless networks along with specialized solutions that can assist the related organizations or the public to fathom how great of an impact these challenges can bring if every related stakeholder took a step in reducing them. Through this paper it is discovered that there are many ways these challenges can be mitigated, however, the lack of implementation of privacy and security solutions is still largely present due to the absence of practical application of these solutions by responsible parties in real world scenarios.

Traditional image steganography conceals secret messages into unprocessed natural images by modifying the pixel value, causing the obtained stego different from the original image in terms of statistical distribution, thereby could be detected by a well-trained classifier for steganalysis. To ensure the steganography is imperceptible and in line with the trend of art images produced by Artificial Intelligence Generated Content (AIGC) becoming popular in social networks, this paper proposes to embed hidden information throughout the process of the generation of an art-style image by designing an image style transformation neural network with steganography function. The proposed scheme takes a content image, an art-style image, and messages to be embedded as inputs, processing them with an encoder-decoder model, and finally generates a styled image containing the secret messages at the same time. An adversarial training technique is applied to enhance the imperceptibility of the generated art-styled stego image with from plain style-transferred images. The lack of the original cover image makes it difficult for the opponent learning a steganalyzer to identify the stego. The recommended approach can successfully withstand existing steganalysis techniques and attain the embedding capacity of 3 bits per pixel for a color image, according to experimental results.

As the control brain of the petrochemical plant, blast resistant performance requirements of the petrochemical control room should be guaranteed when the vapor cloud explosion occurs in the petrochemical production process. 3D-Kagome truss core sandwich structure is a kind of blast resistant material with high energy absorption. Considering the influence factors of the radius of the truss core rod and thickness of the upper and lower panels, in this paper, blast resistant performance of a real steel petrochemical control room with 3D-Kagome truss core sandwich wall is analyzed. With the optimization goal of plastic deformation energy and panel displacement, the optimal wall thickness and radius of the truss core rode are obtained. The optimized blast resistant wall is assembled, and the dynamic response of the steel petrochemical control room with the 3D-Kagome truss core sandwich blast resistant wall is analyzed. The simulation results show that the truss core layer does not dissipate the blast energy effectively when the radius ratio of the truss core rod is larger than 2.7% of the total thickness of the wall; with the increase of the thickness of the upper and lower panels, the proportion of plastic deformation energy of the truss core layer increases gradually and then tends to be a stable proportion value, that is about 90%; When the thickness ratio of the panel is 6.7% of the total one of the wall and the radius ratio of the truss core rod is 2.7% of the total thickness of the wall, the optimal blast resistant 3D-Kagome sandwich wall is determined.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

In order to alleviate the conflict between populations and land-resource, Tianjin has adopted multi-phase reclamation projects to formed large-scale artificial reclamation land. However, the reclamation areas are susceptible to subsidence, which demonstrate a serious threat to infrastructure and people’s lives and property. The SBAS-InSAR was used to acquired surface deformation of Tianjin Binhai New Area from January 2017 year to December 2022 year, analyzed in depth the response relationship between land subsidence and reclamation projects time as well as the land use type. The results show that the Lingang Industrial Zone was the earliest to be reclaimed, with extensive reclamation completed by 2016 year, while Nangang Industrial Zone and Hangu Port started reclamation projects in 2009 year, some areas are still currently under construction. There is a strong correlation between surface deformation and reclamation time, the severe land subsidence occurred over newly reclaimed areas. Surface deformation gradually intensifies from west to east, the maximum surface settlement in Nangang Industrial Zone, Lingang Industrial Zone from the west to the east has changed from -50 mm to -890 mm,45 mm to -580 mm, respectively, reclamation area of Hangu Port with maximum surface deformation is -250 mm. Significant differences deformation among different land use types, which reclamation projects completed in the same time. Subsidence is positively correlated with surface load, in areas with higher surface loads, the surface settlement is also severer,the average surface settlement for the heavy shipyard, 67 grain storage tanks, 27 grain storage tanks, road, and bare land are -201 mm, -166 mm, -107 mm, -64 mm, and -43 mm, respectively. This study reveals significant differences of surface deformation in the reclamation completed at different times and the load is the main driving factor of settlement difference in the reclamation land completed at the same time. Which has important guiding significance for preventing and controlling geological disasters in the reclamation area and later development planning.

In this work, magnetic CuFe₂O₄/Ag nanoparticles activated by porous covalent organic frameworks (COF) was fabricated to evaluate the heterogenous reduction of 4-nitrophenol (4-NP). The core-shell CuFe₂O₄/Ag@COF was successfully prepared by polydopamine reduction of silver ions on CuFe₂O₄ nanoparticles, followed by COF layer condensation. With integrating the intrinsic characteristics of the magnetic CuFe₂O₄/Ag core and COF layer, the obtained nanocomposite exhibited features of high specific surface area (464.21 m² g^-1), ordered mesoporous structure, strong environment stability, as well as fast magnetic response. Accordingly, the CuFe₂O₄/Ag@COF catalyst showed good affinity towards 4-NP via π-π stacking interactions and possessed enhanced catalytic activity compared with CuFe₂O₄/Ag and CuFe₂O₄@COF. The pseudo-first-order rate constant of CuFe₂O₄/Ag@COF (0.77 min^-1) is 3 and 5 times higher than CuFe₂O₄/Ag and CuFe₂O₄@COF, respectively. The characteristics of bi-catalytic CuFe₂O₄/Ag and the porous COF shell of CuFe₂O₄/Ag@COF made a contribution to improve the activity of 4-NP reduction. The present work demonstrated a facile strategy to fabricate COF activated nano-catalysts with enhanced performance in the fields of nitrophenolic wastewater treatment.

Ensuring equal access to affordable higher education for women and men has become a crucial target of UNESCO’s SDG4-Education 2030. Currently, about one-third of the world's college-age population participates in higher education, while the gender disparity persists in various systems. This study employed GDP per capita, gross enrollment ratio (GER), and the gender parity index (GPI) to demonstrate how the education systems have expanded resulting in the transformation of gender parity. We selected Japan, Korea, Taiwan, and the UK as research targets using a cross-correlation function and trend analysis to detect concurrent relationships and future trends with GDP per capita, GER, and GPI. The findings suggest Japan, Korea, and the UK continue to show gender disparity and need to respond to this issue in their policy intervention for SDG4-Education 2030. The results reveal a potential problem in the UK when GPI growth might become unlimited with females dominated. This study suggests the higher education expansion phenomenon and gender diversity in mass and universal systems can be detected by the trend analysis with GDP per capita, GER, and GPI in different settings. The design of the study provides an example to explore the gender diversity patterns in higher education systems for sustainable development.

Keywords: Deep mining; Drill bit structural parameters; Fidelity coring; Abaqus simulation and analysis.

: Exploiting the relationship between the stacking modes of molecules and room-temperature phosphorescence (RTP) performance is of great important to design afterglow materials. A series of coordination polymers base on carbazole–isophtalic acid are synthesized. These compounds exhibit stacking-dependent RTP. It reveals that the phosphorescence efficiency is not proportional to the overlap of p–p stacking, the triplet excited states of discrete dimer mode rather than H-aggregation can dominate the generation of room-temperature phosphorescence. Besides, compounds 1 and 2 exhibit obvious time-dependent RTP with the afterglow color from orange to green, and show white-light emission owing to fluorescence and phosphorescence dual emission. These results indicate that coordination induction is an efficient approach to regulate the aggregation of chromophores, further modulate the room-temperature phosphorescence.

conclusions. The blends of ultrahigh molecular weight polyethylene/polypropylene (UHMWPE/PP) possess excellent processability, but limited by its reduced mechnical properties. Herein, the high mechanical properties and wear—resistance UHMWPE/PP composites were fabricated by the addition of silicon carbide (SiC) nanoparticles under a consecutive elongational flow without any other additives or solvents. The morphology and thermal properties, mechanical properties, wear resistance as well as scratch resistance of UHMWPE/PP/SiC composites were investigated . The mechanical properties and friction resistance of composites increase initially then decrease with the increase content of SiC. The optimum mechanical properties of UHMWPE/PP/SiC composites are achieved when the content of SiC is 3 phr. In addition, both the hardness and scratch resistance of composites improved upon increasing the content of SiC. These improved mechanical properties and wear resistance originate from the well disperison of SiC nanoparticles along with favourable interfacial adhesive under a consecutive elongational flow.

The cause-effect relationship between iron deficiency anemia (IDA) and osteoporosis has not been established in the general population. Thus, the current longitudinal study determined the role of IDA as a risk factor for osteoporosis by analyzing a large nationwide population-based sample. In a sample of 1,000,000 randomly sampled individuals from the 1998-2012 Taiwan National Health Insurance Research Database, patients with IDA (case group [n=35,751]) and individuals without IDA (control group [n=178,755]) were compared. Patients who were <20 years of age and who had pre-existing osteoporosis prior to the diagnosis of IDA were excluded. Each patient with IDA was age- and gender-matched to 5 individuals without IDA. The diagnoses of IDA and osteoporosis (coded using ICD-9CM) were further confirmed with blood test results and X-ray bone densitometry to ensure the accuracy of the diagnoses. Osteoporosis occurred more often among patients with IDA compared to individuals without IDA (2.27% vs. 1.32%, p<0.001). Cox proportional hazard analysis revealed that the risk for osteoporosis was significantly higher in the case than the control group (hazard ratio [HR]=1.74; 95% CI=1.61-1.88) and remained similar after adjustment for covariates (adjusted HR=1.81; 95% CI=1.67-1.97). Compared with individuals without IDA, the risk for osteoporosis was even higher for patients with IDA who received intravenous ferrum therapy (adjusted HR=2.21; 95% CI=1.85-2.63). In contrast, the risk for osteoporosis was reduced for patients with IDA who received a blood transfusion (adjusted HR=1.47; 95% CI=1.20-1.80). As a predictor, prior IDA is a significant and independent risk factor for development of osteoporosis. In contrast to blood transfusion treatment, the use of intravenous ferrum may further increase the risk for future osteoporosis.

The autonomous displacement and displacement measurement functions of the maglev ruler are performed by the mover core. The stability of the four magnetic field in air gaps and the levitation position of the maglev ruler is one of the key factors for the stability of the thrust force on the power core, and it is also one of the key factors for ensuring the precision of the maglev ruler. There is cross-coupling between the two ends of the mover core of the maglev ruler, resulting in a strongly coupled, nonlinear, multi-input and multi-output system for the levitating system of the maglev ruler. This paper establishes a mathematical model for the levitating system of the maglev ruler, and designs a levitating control system for the maglev ruler based on ADRC control algorithm to achieve decoupling and disturbance suppression. Through simulation analysis and experimental testing of the levitating system with starting and disturbance, it is proved that the levitating control system of the maglev ruler has good dynamic characteristics, static characteristics, and robustness.