Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

Co-free Li-rich oxide is a promising cathode for low cost high energy density Li-ion battery but presents poor cyclic stability. To address this issue, CeO2 is coated on Co-free Li-rich oxide through a low-temperature aged process, resulting in a novel CeO2-coated Li-rich oxide compo-site. Due to the low-temperature aged process, a uniform CeO2 coating layer of 6 nm in thickness is successfully coated on Co-free Li-rich oxide. With this uniform coating, the resulting CeO2-coated Li-rich oxide composite presents improved cyclic stability as well as rate capability as the cathode of Li-ion battery. The capacity retention of the resulting CeO2-coated Li-rich oxide is enhanced from 67% to 85% after 100 cycles and its capacity retention of 5C/0.05C is enhanced from 10% to 23%, compared with the uncoated sample. Such significant improvements enable this low-temperature aged process to be helpful for the practical application of Li-rich oxide materials, not limited to Co-free Li-rich oxide.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying impacts the size and distribution of primary phase particles and the dimension of eutectic cells. Small interdendritic spacing in the range of 10-15 um enables substitution of the initial long-term homogenization annealing by a two-step annealing at 300 and 450 °C and a short solution treatment at 530 °C before quenching and the final age-hardening procedure. A dense dispersion of small Al3(Sc,Zr) precipitates intensively inhibiting recrystallization forms during this treatment. Further refining and fragmentation of the structure were performed using constrained groove pressing before the solution treatment. Small pre-straining of quenched specimens and subsequent age-hardening simulating T8 temper were used to promote the formation of a homogeneous distribution of strengthening particles and to suppress preferential heterogeneous precipitation on subgrain and grain boundaries. Microstructural features and microhardness evolution during annealing were critically examined and confronted with microstructural characteristics observed on reference mold cast alloy or alloys without Sc alloying. The proposed treatment represents a model near net shape procedure for manufacturing thicker sheets for the aerospace industry.

Molecular dynamics (MD) simulations present a sophisticated nano-scale computational approach that can play a critical role in material design for next generation batteries. One critical piece of information needed for MD simulations is the non-bonded potential parameters, which can be obtained through quantum mechanics (QM) calculations or experimental methods. However, experimental data is not available for exploratory and novel materials to derive the potential parameters. Also, the QM approach needs significant computational power and is too time consuming for large systems. On the other hand, current Artificial Intelligence techniques are faster, but they cannot be generalized across molecules and properties. As a result, there is a significant barrier to discovering and exploring new materials. Overcoming this barrier, in this work, we propose a Machine Learning (ML) based technique that can learn inter-atomic potential parameters for various particle-particle interactions employing QM calculations. This ML model can be used as an alternative for QM calculations for predicting non-bonded interactions in a computationally efficient manner. Using these parameters as input to MD simulations, we can predict a diverse range of properties, enabling researchers to design new and novel materials suitable for various applications in the absence of experimental data. We employ our ML-based technique to learn the Buckingham potential, a non-bonded interatomic potential. Subsequently, we utilize these predicted values to compute the densities of four distinct molecules, achieving an accuracy exceeding 93%. This serves as a strong demonstration of the efficacy of our proposed approach.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Accurate lithium battery diagnosis and prognosis is critical to increase penetration of electric vehicles and grid-tied storage systems. They are both complex due to the intricate, nonlinear, and path-dependent nature of battery degradation. Data-driven models are anticipated to play a significant role in the behavioral prediction of dynamical systems such as batteries. However, they are often limited by the amount of training data available. In this work, we generated the first big data comprehensive synthetic datasets to train diagnosis and prognosis algorithms. The proof-of-concept datasets are over three orders of magnitude larger than what is currently available in the literature. With benchmark datasets, results from different studies could be easily equated, and the performance of different algorithms can be compared, enhanced, and analyzed extensively. This will expend critical capabilities of current AI algorithms, tools, and techniques to predict scientific data.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

In recent times, there has been significant enthusiasm for the development of all solid state batteries. This interest stems from a dual focus on safety—addressing concerns related to toxic and flammable organic liquid electrolytes—and the pursuit of high energy density. \cite{SCHNELL2018160,Zheng2018}. While liquid electrolyte batteries constitute for now the vast majority of commercial cells, solid electrolyte batteries show great promise. In parallel with experimental research, computational models \cite{GrazioliEtAlCM2016} clarify the several fundamental physics \cite{LiMonroeARCBM2020} that take place throughout battery operations. We review some classical models, emphasizing the conceptual advancements documented in the most recent works.

The possibility of using graphane monolayer crystals as the electrode material is becoming popular. Graphane is stable at room temperature and has large surface area, but its chemical inertness hinders its direct interactions with Li ions. In this study, we performed density functional theory calculations to study the energetic stability, structural and electronic properties of Li on graphane with various CH divacancy configurations (v12, v13 and v14 ). The results show that adsorption of Li atom reduces the formation energy of the CH divacancy configurations. The Li-v12 is most stable with the highest binding energy of 3.25 eV/Li and relaxes to in-plane with other C atoms. Altering the Li charge state to have Li−1-v12 or Li+1 -v12 affects the energetic stability and electronic characters of Li-v12 . The Li−1-v12 (Li +1-v 12 ) enhances (reduces) the binding force between Li and v 12 configuration, and furthermore it improves (deteriorates) the conductivity of the structure. Further investigation of graphane with vacancies is encouraged due to these intriguing observations, as it holds promise for potential utilization as an electrode material.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

As one of the critical state parameters of the battery management system, lithium battery state of charge (SOC) can provide an essential reference for battery safety management, charge/discharge control, and energy management of electric vehicles. To analyze the application of deep learning in electric vehicle power battery SOC estimation, this study reviewed the technical process, common public datasets, and the neural networks used, structural characteristics, advantages and disadvantages of lithium battery SOC estimation in deep learning method. First, the specific technical processes of the deep learning method for SOC estimation were analyzed, including data collection, data preprocessing, feature engineering, model training, and model evaluation. Secondly, the current commonly and publicly used lithium battery dataset was summarized. Then, the input variables, data sets, errors, and advantages and disadvantages of four types of deep learning methods, were concluded using the structure of neural network used for training as the classification criterion. Finally, the challenges and future development directions of lithium battery SOC estimation in deep learning method were explained.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

In this paper the application of recycled Li-ion batteries spent cathode (LIB-SC) combined with NaHCO₃/H₂O₂ system is presented for the first time in the literature as an alternative for degradation of potentially toxic organic molecules. The model pollutant choice was methylene blue molecule. The spent cathode composition corresponds to LiCoO₂, which was proved by the XRD and EDX. Regarding the decolorization of methylene blue solution, the addition of NaHCO₃ in comparison with only H₂O₂ reduces the complete decolorization time in 96%. This reduction occurs because the radical CO₃ is more stable than OH. In this way, the application the system proposed in this article is aimed at solving two major global problems: the disposal of cell phone batteries and the pollution of liquid effluents.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

This code provides computational facilities to simulate current versus time during the charging of Li-ion cells at desire constant voltage by considering multiscale physical phenomena. This code only considers a powder of active materials (at microscale or nanoscale) and a small part of electrolyte around it as a half cell. Then it is extended to a complete cell by applying correct boundary conditions. This code is very useful by modifying code parameters to understand the effect of the complex shape of active materials powder (surface area and powder size), kind of electrolyte, and the applied voltages on the charging response of Li-ion cell. As a summary, a microscale approach to the design of Li-ion cells has been provided via this code.

In this study, Li-Al-OH layered double hydroxide (LDH), which was prepared by solvent-free one-step mechanochemical reaction of LiOH and Al(OH)₃, was applied to remove boron from aqueous solution. Dry-grinding for 3 h at a rotational speed of 500 rpm, Li/Al molar 1/2 was the optimum condition to prepare highly crystalline of Li-Al LDH phase with no evident impure phases. Two milling products with Li/Al molar ratio at 1/2 and 2/2 were evaluated for boron adsorption. The results confirmed that Li/Al molar ratio 2/2 sample showed high boron adsorption capacity due to the physical adsorption of Li-Al-OH LDH and chemical synergism of phase gel Al(OH)₃. The adsorption isotherms, described by the Langmuir model, indicated maximum monolayer boron uptake capacity 45.45 mg/g, implying competitive adsorption capacity of the material in our experiment.

Background: The liver is involved in disseminated tuberculosis in more than 80% of the cases while primary liver involvement is rare, representing < 1% of all cases. Hepatic tuberculosis (TB) can be treated by conventional anti-TB therapy, however, diagnosing this disease still remains a challenge. The diagnosis might be particularly difficult in patients with a single liver lesion that could be misdiagnosed as a tumor or other focal liver lesions. While computed tomography and magnetic resonance imaging findings have been described, there is a paucity of literature on contrast-enhanced ultrasound (CEUS) features of hepatic TB. Case Summary: herein, we describe a case of a patient with tuberculous lymphadenopathy and chronic HCV-related liver disease who developed a single macronodular hepatic TB lesion. Due to the finding of a hepatocellular carcinoma (HCC) highly suggestive CEUS pattern, specifically a LR5 category according to the Liver Imaging Reporting and Data System (LI-RADS), and a good response to antitubercular therapy, a non-invasive diagnosis of HCC was made, and the patient underwent liver resection. We also review the published literature on imaging features of hepatic TB and discuss the diagnostic challenge represented by hepatic TB when occurs as a single focal liver lesion. Conclusions: this report shows for the first time that CEUS pattern of hepatic TB might be misinterpreted as HCC and specific imaging features are lacking. Personal history and epidemiological data are mandatory in interpreting CEUS findings of a focal liver lesion even when the imaging pattern is highly suggestive of HCC.

This work simulates the performance of lithium batteries for electric vehicles under different charge and discharge rates. The simulation is based on similarity factors for power, voltage and current, reproducing the real operation conditions of an electric vehicle at the model scale. Most current driving modes have been analysed corresponding to discharge rates from 0.1C to 0.37C. The simulation has also been applied to determine charging time using charge power in real conditions, from 6.1 kW to 18.3 kW (0.1 C to 0.3C). Driving conditions are obtained using equations for vehicle motion including all forces. Tests have been run under two configurations, continuous and alternate current circuits, to reproduce the two types of engines that electric vehicles use. The simulation shows very good agreement in charge and discharge processes, average deviation of 3% related to real conditions, and 1.6% between them, which proves the validity of the simulation process.

A novel composite consisting of fluorine-doped carbon and graphene double-coated LiMn0.6Fe0.4PO4 (LMFP) nanorods, synthesized via a facile low temperature solvothermal method that employs a hybrid glucose and polyvinylidene fluoride as carbon and fluorine sources. As revealed by physicochemical characterization, F-doped carbon coating and graphene form a ‘point-to-surface’ conductive network, facilitating rapid electron transport and mitigating electrochemical polarization. Furthermore, the uniform thickness of the F-doped carbon coating alters the growth of nanoparticles and prevents direct contact between the material and the electrolyte, thereby enhancing structural stability. Strong electronegative F− is beneficial to inhibit the structural changes of LMFP caused by Li-insertion/extraction during charge/discharge, which effectively reduces the Jahn-Teller effect, and inhibits Mn dissolution. The distinctive architecture of LMFP/C-F/G cathode material exhibits excellent electrochemical properties, exhibiting an initial discharge capacity of 163.1 mAh g−1 at 0.1 C and a constant Coulombic efficiency of 99.7% over 100 cycles. Notably, LMFP/C-F/G cathode material achieves an impressive energy density of 607.6 Wh kg−1 , surpassing that of commercial counterparts. Moreover, it delivers a reversible capacity of 90.3 mAh g−1 at a high current rate of 5 C. The high-capacity capability and energy density of the prepared materials give them great potential for use in next-generation lithium-ion batteries.

Li-rich layered oxide cathode materials have become one of the most promising cathode materials for high-energy-density lithium-ion batteries owning to its high theoretical specific capacity, low cost, high operating voltage and environmental friendliness. Yet they suffer from severe capacity and voltage attenuation during prolong cycling, which blocks their commercial application. To clarify these causes, we synthesize 0.5Li2MnO3·0.5LiNi0.8Co0.1Mn0.1O2 (LL-811) with high-nickel-content cathode material by a solid-sate complexation method, and it manifests a lot slower capacity and voltage attenuation during prolong cycling compared to LL-111 and LL-523 cathode materials. The capacity retention at 1C after 100 cycles reaches to 87.5% and the voltage attenuation after 100 cycles is only 0.460 V. Combining X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscopy (TEM), it indicates that increasing the nickel content not only stabilizes the structure but also alleviates the attenuation of capacity and voltage. Therefore, it provides a new idea for designing of Li-rich layered oxide cathode materials that suppress voltage and capacity attenuation.

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

This is an exercise to explore the concentration of Lithium, Lithium-7 isotope and the possible presence of black dirty ice in the lunar surface using spectral data obtained from the Clementine mission. The main interest in tracing the lithium and presence of dark ice in the lunar surface are closely related to future human settlement missions in the Moon. We investigate the distribution of Lithium and 7 Li isotope on the Lunar surface, employing spectral data from the Clementine images. We utilized Visible (VIS-NIR) imagery at wavelengths of 450, 750, 900, 950, and 1000 nm, along with Near-Infrared (NIR-SWIR) at 1100, 1250, 1500, 2000, 2600, and 2780 nm, encompassing 11 bands in total. This dataset offers a comprehensive coverage of about 80% of the lunar surface, with resolutions ranging from 100 to 500 meters, spanning latitudes from 80°S to 80°N. In order to extract quantitative abundance of Lithium, ground truth sites were used to calibrate the Clementine images. Samples (12045, 15058, 15475, 15555, 62255, 70035, 74220 and 75075) returned from Apollo missions 12, 15, 16 and 17 have been correlated to the Clementine VIS-NIR bands and five spectral ratios. The 5 spectral ratios calculated synthesize the main spectral features of sample spectra that were grouped by their Lithium and 7 Li content using Principal Component Analysis. The ratios spectrally characterize substrates of anorthosite, silica-rich basalts, olivine-rich basalts and High-T mare basalts and Orange soils. Our findings reveal a strong linear correlation between the spectral parameters and the lithium content in the 8 Apollo samples. With the values of the 11 Clementine bands and the 5 spectral ratios for each of the 8 lunar soils we performed linear regression models to estimate the concentration of Lithium and 7 Li. Also, we calculated Digital Terrain Models (DTMs; Altitude, Slope, Aspect, DirectInsolation and WindExposition) from LOLA-DTM to discover relations between relief and spatial distribution of the extended models of lithium and 7 Li. The analysis was conducted in a mask polygon extracted from Lunar Orbiter Laser Altimeter (LOLA) and located around the Apollo 15 landing site. This analysis seeks to uncover potential 7 Li enrichment through spallation processes, influenced by varying exposure to solar wind. To explore the possibility of find ice mixed with regolithe (black ice) we used a spectral library (350-2500nm) form ices dirty with different concentration of volcanic particles.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitable homogenization temperature and duration is a crucial step in assuring a homogeneous distribution of alloying elements and optimal exploitation of the potential of the alloy. In-situ heating in an electron microscope was performed on a twin-roll cast Al-Cu-Li-Mg-Sc-Zr alloy to understand the peculiarities of the homogenization process. Four types of primary phase particles rich in Cu, Li, Mg, and Fe were identified in the as-cast material. They appear as coarse particles at the boundaries of eutectic cells. Their partial dissolution occurs at temperatures above 450 °C. They are almost fully dissolved at 550 °C, except for complex phases containing Fe and Cu. Small dimensions of eutectic cells in the range of 10 µm assure a homogeneous distribution of main alloying elements within the matrix after 20 min of annealing. Direct comparison with the same material prepared by mold-casting indicates that such short annealing times result in the dissolution of main primary phase particles but do not assure a homogeneous distribution of alloying elements in the whole volume of the specimen.

Universitas Sebelas Maret (UNS) through SMART UNS Company has conducted research and development of e-motorcycle conversion using Li-ion battery pack as a substitute for ICE energy source from the conventional motorcycle. Currently, the battery-pack that used for e-motorcycle conversion is in the development phase towards commercialization. The challenge of estimating production costs is the complicated production process and storing hidden expenses that can be a problem. This hidden cost is often a missing or varied factor that costs less or more expensive. This study presents an integrated parametric cost estimation model with activity-based cost assignments to estimate production costs through cost calculations for each activity. Activity-based costs break the production process into a specific cost element for each step. Each activity's cost is put into a parametric cost estimation model to calculate the cost of each activity into the total cost of production. Cost estimation results will be analyzed using a regression method to determine which variables most affect the production cost of Li-ion battery packs for the conversion of e-motorcycles in the SMART UNS company.

Li₂TiO₃ nanopowders were synthesized by hydrothermal process using anatase TiO₂ and LiOH H₂O as raw materials. Li₂TiO₃ crystallizes in the layered monoclinic structure (space group C2/c) with average crystallite size of 34 nm. Morphology, elemental composition and local structure of products were carried out using HRTEM, FESEM, EDS, Raman and FTIR spectroscopy. Transport properties investigated by d.c. (4-probe measurements) and a.c. (complex impedance spectroscopy) show the activation energy of 0.71 and 0.65 eV, respectively. The ionic transport properties of Li⁺ ions in nanocrystalline Li₂TiO₃ characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) validate the good electrochemical properties of this anode material for lithium-ion batteries.

CoCr2O4 and doped lithium Co1-xLixCr2O4 chromate powder and nanoparticles were prepared by modified by sol-gel method. The morphological and structural properties of nano chromates were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and Photoluminescence (PL). Nanoparticles of doped lithium were synthesized by adding appropriate amount of cobalt nitrate, chromium nitrate, lithium nitrate and 1,2 Ethanediol as a complexing agent. The sample were heated at 105 ˚C for ten hours in oven to obtain dry gel. Calcination temperature for these samples was 700˚C for 3 hours in a furnace. The particle size of parent compound ranges from 4.4 nm to 11 nm, determined by SEM. The tendency of particles to form the aggregates with the increased annealing temperature was observed. The SEM and optical characterization of this compound has shown the sol gel derived material may be successfully used as an effective doped lithium cobalt ceramic pigment with controlled variation in structural and optical properties. SEM images showed that spherical like doped particle have diameter 33nm. From PL spectra Nano structure shows band gap 2.5ev and when we doped Lithium in it band gap decreases and become 1.19ev, which is associated to band gap transition.

To address the limitations of the current anodes of Li+-ion batteries (LIBs), a Ge/GeO2/Carbon (Ge@GeO2-C) composite was designed by introducing a high-energy ball-milling process for advanced LIBs. Ge@GeO2-C is prepared and characterized by XPS, XRD, SEM, and TEM, which facilitate synthesis and provide controllability with respect to milling time. Interestingly, as the ball-milling time increased, the proportion of metallic Ge increased during the carbon thermal reduction reaction. The electrochemical characteristics of Ge@GeO2-C are assessed using differential capacity analysis (dQ/dV) and galvanostatic charge-discharge techniques to confirm its viability as an anode material in LIBs. The results demonstrated decent initial and secondary capacities of approximately 1800 mAh g-1 (for the first cycle) and 838 mAh g-1 (for the second cycle) at a rate of C/60 by the reaction between Ge and the Li-Ge complex. Furthermore, postmortem characterization was performed to gain an understanding of the material, suggesting future prospects for advanced LIBs.

Taking advantage of fact that the surface electrons of metallic nanoparticles (NPs) can be effectively released even at a low voltage bias, we demonstrate an improvement in the electrochemical performance of nano-sized Prussian Blue (PB) based secondary batteries by the incorporation of bare Ag or Ni NPs onto the vicinity of the working PB NPs. It is found that the capacity for electrochemical energy storage of the 17-nm-PB-based battery is significantly higher than the capacity of 10-nm-PB-based, 35-nm-PB-based or 46-nm-PB-based batteries. There is a critical PB size for the highest electrochemical energy storage efficiency. The full specific capacity CF of the 17-nm-PB-based battery stabilized to 62 mAh/g after 130 charge-discharge cycles at a working current of IW = 0.03 mA. The addition of 14 mass-percent of Ag NPs in the vicinity of the PB NPs gives rise to a 32% increase in the stabilized CF. A 42% increase in the stabilized CF can be obtained with the addition of 14 mass-percent of Ag NPs on the working electrode of the 35-nm-PB-based battery. An enhancement of CF is also found for electrodes incorporating bare Ni NPs but the effect is smaller.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

The abundant use of lithium-ion batteries (LIBs) in a wide variety of electric devices and vehicles will generate a large number of depleted batteries, which contain several valuable metals such as Li, Co, Mn, and Ni present in the structure of the cathode material (LiMO2). The present work investigates chemical, technological, and environmental aspects in the treatment of such wastes, development of a methodology for the extraction of lithium, cobalt, nickel, manganese, and graphite by a carbochlorination pyrometallurgical process. Mixtures of cathode and anode materials (called black mass, mixed oxides of Li, Co, Ni, Mn, and graphite) from different LIBs, carbon black (as reducing agent), and CaCl2 (as chlorinating agent) were used. Non-isothermal thermogravimetric tests up to 850°C and isothermal tests at 700°C of the mixtures in an inert atmosphere were carried out. It was experimentally observed that the LiMO2-C-CaCl2 reaction takes place at 700°C. LiCl, Ni, and Co were obtained as final products, and to a lesser extent, CoO, NiO, and MnO2. CaCO3 was also obtained as a by-product. The obtained results show that carbochlorination is an efficient and effective alternative route for the extraction and recovery of metals from different LIBs, focused on the sustainability and circular economy

Retired Electric vehicles (EVs) batteries are reused in second life energy storage applications. However, the overall performance of repurposed energy storage system (ESS) is limited by the unevenness of individual batteries use in it. Therefore, battery grading is required for optimal performance of ESS. Electrochemical impedance spectroscopy (EIS) based evaluation of battery aging is a promising way to grade lithium-ion batteries. However, it is not practical to measure impedance of mass retired batteries due to high complexity and slowness. In this paper, a broadband multi-sine binary signal (MSBS) perturbation integrated with multichannel EIS system is presented to measure impedance spectra for high-speed aging evaluation of lithium-ion batteries or modules. The measurement speed is multi-times higher than conventional EIS with single-channel configuration. The broadband MSBS is validated with reference sinusoidal sweep perturbation and corresponding root-mean-square error (RMSE) analysis is performed. Moreover, the accuracy of the presented multichannel EIS system is validated by impedance spectra measurement of Samsung INR18650-29E batteries and comparing it with those measured with commercial EIS instrument. A chi-squared error under 0.641% is obtained for all 8-channels. Since the non-linearity of battery has significant impact on quality of impedance spectra. Therefore, Kronig-Kramer (KK) transform validation is also performed.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Lithium sulfur (Li–S) batteries are expected to be very useful for next-generation transportation and grid storage because of their high energy density and low cost. However, their low active material utilization and poor cycle life limit their practical application. The use of a carbon-coated separator in these batteries serves to inhibit the migration of the lithium polysulfide intermediate and increases the recyclability. We report the extent to which the electrochemical performance of Li–S battery systems depends on the characteristics of the carbon coating of the separator. Carbon-coated separators containing different ratios of carbon black (Super-P) and vapor-grown-carbon-fibers (VGCF) were prepared and evaluated in Li–S batteries. The results showed that larger amounts of Super-P on the carbon-coated separator enhanced the electrochemical performance of Li–S batteries; for instance, the pure Super-P coating exhibited the highest discharge capacity (602.1 mAh g-1 at 150 cycles) with a Coulombic efficiency exceeding 95%. Furthermore, the separators with the pure Super-P coating had a smaller pore structure, and hence limited polysulfide migration, compared to separators containing Super-P/VGCF mixtures. These results indicate that it is necessary to control the porosity of the porous membrane to control the movement of the lithium polysulfide.

MoS2 lithium-based grease is suitable for lubrication protection between bearings at high temperatures and loads due to its excellent tribological properties. However, there is little research on the influence of different addition methods of MoS2 additive on the tribology and corrosion properties of lithium grease. In this work, vegetable oil with low toxicity, high biodegradation rate, and low cost was selected as the base oil, lithium 12-hydroxystearate as the thickener, and MoS2 as the additive. The effects of different adding modes of MoS2 on the tribology and corrosion properties of lithium grease were studied. The experimental results showed that adding 0.01wt% MoS2 before thickening was more conducive to improving the tribological properties of lithium grease. The average friction coefficient was 0.034, and the average spot diameter was reduced by 0.16mm. After grinding and adding 0.01wt% MoS2, the corrosion inhibition efficiency of the steel sheet was as high as 96.97%. The main reason was that the longer stirring and grinding were conducive to the uniform distribution of MoS2 in the grease, and the protective film formed by MoS2 and GCr15-bearing steel improved the lubrication performance and corrosion inhibition performance of the friction system.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

Apiaceae plants have been widely used as traditional Chinese medicines (TCMs) for the treatment of removing dampness, relieving superficies, and dispelling cold, etc. In order to exploit the potential application and improve the yield and quality of Apiaceae medicinal plants (AMPs), The traditional use, phytochemistry, modern pharmacological use, effect of bolting and flowering (BF), and approaches for controlling the BF were summarized. Currently, about 228 AMPs have been recorded as TCMs with 6 medicinal parts, 72 traditional uses, 62 modern pharmacological uses, and 5 main kinds of metabolites. Three effect degrees (i.e., significantly affected, affected to some extent, and no significantly affected) could be classed based on the yield and quality. The BF of individual plants (e.g., Angelica sinensis) could be effectively controlled by the standard cultivation techniques, while the mechanism of BF has not been systemically revealed. This review will provide useful references for the reasonable exploration and high-quality production of AMPs.

In 2020 the world experienced the threat of the COVID-19 epidemic, as seniors and chronic disease patients typically try to reduce their exercise and social activities to avoid increasing the risk of infection, which could lead to increased loneliness and even many diseases. This research combining golf croquet games with AIoT companion robots constructs a home-based intelligent exercise system thus uses the Technology Acceptance Model (TAM), deduces users’ intention to use this system based on perceived usefulness and perceived ease of use, and adds the needs of love and belonging, esteem, cognitive, aesthetic, and self-actualization in Maslow’s needs theory to conduct system needs analysis. The analysis results show that participants have a high level of acceptance of this system, believing that it is easy to learn and operate, can increase interaction with others, also found that this system can improve self-confirmation, satisfying the third for knowledge, feeling happy, and self-actualization needs are easier to fulfill. In the future, we shall collect and record the seniors in the process of use, so as to find out their health problems as soon as possible, expand their daily life through this exercise, and achieve the goal of happy living and health care.

The broad acceptance of electromobility depends heavily on the performance and service life of the battery technology used. Lithium-ion battery technology is currently the most promising energy storage technology for mobile applications, but the performance and capacity of the cells is extremely temperature sensitive. Especially in these new complex and powerful applications there is a significant need for thermal management. Depending on the ambient conditions, part of the effective battery energy must therefore be used to temper the system. So far, mainly active components have been used for this task. This not only reduces the overall efficiency, but also increases the weight, volume and maintenance requirements of the system. In the present work, an alternative battery temperature management system (BTMS) was developed. A concept based on latent heat storage materials was created, which uses the advantages of thermal energy storage and the design freedom of additive manufacturing technology, and its suitability for use in battery applications was checked. On the one hand, the use of systems for storing thermal energy was researched and, on the other hand, an innovative cooling concept was created considering new production possibilities.

Although 7055 aluminum alloy is a deformed aluminum alloy and will show excellent mechanical properties after recrystallization after large deformation, it is a method to enrich its application range if rare earth is added and the rare earth phase dispersion is promoted by heat treatment. This article used optical microscopy, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), micro Vickers hardness and room temperature stretching methods to study the as-cast 7055-xEr (x=0wt.%, 0.2wt.%, 0.4wt.%, 0.6wt.%, 0.8wt.%) aluminum alloy after being subjected to 460 oC×3h homogenization and 410 oC×1h solid solution+150 oC×12h aging treatment the changes in microstructure and properties. The results indicated that: when 0.2wt.%Er was added to 7055 aluminum alloy after solution at 410 oC×1h and aging at 150 oC×12h, the dendrite structure was significantly reduced, the grain thinning was obvious and the distribution was uniform, Al8Cu4Er phase appeared in the lamellar eutectic η-Mg(Zn,Al,Cu)2 structure at grain boundaries, and the hardness reached 168.8HV. The yield strength, tensile strength and elongation were 542.12Mpa, 577.67MPa and 8.36%, respectively.

In this paper, we investigate the role of sanctions in the relationship between macroeconomic determinants and foreign direct investment inflows. We also investigate the moderating role of sanctions in FDI inflows into Iran. The empirical results reveal that macro determinants such as infrastructure, exchange rate, inflation rate, investment return, and governance have a long-run impact on FDI inflows in Iran. Our findings also show that GDP growth rate and trade openness have no significant effect on FDI. Our results indicate that sanctions do not have a significant moderating role in the relationship between macroeconomic factors and foreign direct investment. Surprisingly, international sanctions have a positive relationship with FDI inflows in Iran. Furthermore, sanction has a positive impact on the inflation rate and exchange rate in Iran. Finally, our findings show that sanctions have had a significant impact on Iran's economic growth in recent years due to increasing the severity level of sanctions.

Objective: To study the factors affecting the time of umbilical cord shedding in premature infants.Methods: A total of 151 premature infants who were born in the obstetrics department of a Class III hospital in Hefei from November 2020 to June 2021 were selected as subjects. All premature infants and their families met the complete inclusion criteria. A total of 33 related factors from 3 aspects, including the birth situation of premature infants, the condition of premature infants in hospital and the condition of pregnant mothers, were collected for univariate analysis and multiple Logistic regression analysis. The relevant factors affecting the umbilical cord shedding time of premature infants were screened through the univariate analysis results, and the main factors affecting the umbilical cord shedding time of premature infants were screened through the multiple Logistic regression analysis results.it was found that the weight, gestural age, admission age, whether the premature infants were combined with NRDS, the use of antibiotics, the duration in the warm box, the initial temperature in the warm box, the duration of light therapy, the degree of Apgar for 1 minute, the maternal education level had an effect on the time of umbilical cord shedding of premature infants (P < 0.05). Through Logistic multiple regression analysis, it was screened that the duration of premature infants in the incubator was the main factor affecting the umbilical cord shedding time of premature infants (P < 0.05).Conclusion: Factors such as premature infants' weight, gestural age, admission age, whether they are combined with NRDS, antibiotic use, duration in the incubator, initial temperature in the incubator, duration of phototherapy, Apgar level of 1 minute, and maternal education level will affect the umbilical cord shedding time of premature infants. Among them, duration in the incubator is the main factor affecting the umbilical cord shedding time of premature infants.

A flexible asymmetric supercapacitor (ASCs) is successfully developed by using the composite of MoO3 and graphene oxide (GO) electrochemically deposited on carbon cloth (CC) (MoO3/rGO/CC) as the negative electrode, the MnO2 deposited on CC (MnO2/CC) as the positive electrode and Na2SO4/polyvinyl alcohol (PVA) as gel electrolyte. The results show that the introduction of GO layer can remarkably increase the specific capacitance of MoO3 from 282.7 F g-1 to 341.0 F g-1. Furthermore, the combination of such good electrode materials and a neutral gel electrolyte renders the fabrication of high-performance ASC with a large operating potential difference of 1.6 V in 0.5 mol L-1 Na2SO4 solution of water. Furthermore, the ASCs exhibit excellent cycle ability and the capacitance can maintain 87 % of its initial value after 6000 cycles. The fact that a light-emitting diode can be lighted up by the ASCs indicates the device’s potential applications as energy storage devices. The encouraging results demonstrate a promising application of the composite of MoO3 and GO in energy storage devices.

Understanding the spatiotemporal characteristics of merging behavior is crucial for the ad-vancement of autonomous driving technology. This study aims to analyze on-ramp vehicle merg-ing patterns, and investigate how various factors, such as merging scenarios and vehicle types, in-fluence driving behavior. Initially, a framework based on High-Definition (HD) Map is devel-oped to extract trajectory information in a meticulous manner. Subsequently, eight distinct merg-ing patterns (Pattern A to H) are identified, with a thorough examination of their behavioral characteristics from both temporal and spatial perspectives. Merging behaviors are examined temporally, encompassing the sequence of events from approaching the on-ramp to completing the merge. This study specifically analyzes the target lane's spatial characteristics, evaluates the merging distance (ratio), investigates merging speed distributions, compares merging patterns and identifying high-risk situations. Our novel findings reveal that Patterns C and F, with Time-to-Collision (TTC) values less than 2.5 seconds, pose a significantly higher risk than other patterns. In traffic simulations, Patterns B and E can be integrated, as they show negligible differences in speed, distance traveled, and duration. Additionally, the practice of truck platooning has a signif-icant impact on vehicle merging behavior. This study enhances the understanding of merging be-havior, facilitating autonomous vehicles' ability to comprehend and adapt to merging scenarios. Furthermore, this research is significant in improving driving safety, optimizing traffic manage-ment, and enabling the effective integration of autonomous driving systems with human drivers.

In this paper, the research progress on dynamic behaviors of RC structural members is reviewed from experimental, theoretical and numerical perspectives. Firstly, the basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests are presented. Then the theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforcing steel and the proposed modified models of dynamic behavior parameter at the structural member level are summarized. Finally, the available modelling approach and the method for incorporating the dynamic effect in numerical simulation of RC structures are reviewed. Moreover, a brief introduction is made to the dynamic hysteretic model established on the experimental data, which provides an alternative approach to consider the dynamic effect beside the commonly used DIF method. This paper provides valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures, and also puts forward some issues that need to be solved in the future research works..

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

The study aimed to investigate how distributed leadership influences adolescents' social and emotional competence, considering the roles of student-centered instructional practices and teacher self-efficacy. Utilizing survey data from 7,246 Suzhou adolescents enrolled in the SESS program, the study employed multilevel structural equation modeling for analysis. The findings indicated a positive correlation between distributed leadership and adolescents' social and emotional competence, as evaluated by teachers. Moreover, distributed leadership was observed to exert an indirect impact on adolescents' self-assessment and teacher-rated social and emotional competence. This influence operated through several mediators: student-centered instructional practices, teacher self-efficacy, and the sequential mediating pathway of student-centered instructional practices → teacher self-efficacy. This study underscores the significance of supportive elements in fostering students' social and emotional competence. It offers valuable insights into the everyday practices of teachers, principals, and administrators. Additionally, it sheds light on how distributed leadership contributes to enhancing adolescents' overall social and emotional development.

Sea ice extraction and segmentation of remote sensing images is the basis for sea ice monitoring. Machine learning-based image segmentation methods rely on manual sampling and require complex feature extraction. Deep-learning semantic segmentation methods have the advantages of high efficiency, intelligence, and automation. Sea ice segmentation using deep learning methods faces the following problems: in terms of datasets, the high cost of sea ice image label production leads to fewer datasets for sea ice segmentation; in terms of image quality, remote sensing image noise and Severe weather conditions affects image quality, which affects the ac-curacy of sea ice extraction. To address the quantity and quality of the dataset, this study used multiple data augmentation methods for data expansion. To improve the semantic segmentation accuracy, the SC-U2-Net network was constructed using multi-scale inflation convolution and a multi-layer Convolutional Block Attention Module (CBAM) attention mechanism for the U2-Net network. The experiments showed that (1) data augmentation solved the problem of an insuffi-cient number of training samples to a certain extent and improved the accuracy of image seg-mentation. (2) This study designed a multilevel Gaussian noise data augmentation scheme to improve the network's ability to resist noise interference and achieve a more accurate segmenta-tion of images with different degrees of noise pollution. (3) The inclusion of a multi-scale inflation perceptron and multi-layer CBAM attention mechanism improved the ability of U2-Net network feature extraction and enhanced the model accuracy and generalization ability.

Sentinel-2 can provide multi-spectral optical remote sensing images in RGBN bands with a spatial resolution of 10m, but the spatial details provided are not enough for many applications. WorldView can provide HR multi-spectral images less than 2m, but it is a commercial paid resource with relatively high usage costs. In this paper, without any available reference images, Sentinel-2 images at 10m resolution are improved to a resolution of 2.5m through super-resolution (SR) based on deep learning technology. Our model, named DKN-SR-GAN, uses degradation kernel estimation and noise injection to construct a dataset of near-natural low-high-resolution (LHR) image pairs, with only low-resolution (LR) images and no high-resolution (HR) prior information. DKN-SR-GAN uses the Generative Adversarial Networks (GAN) combined of ESRGAN-type generator, PatchGAN-type discriminator and the VGG-19-type feature extractor, using perceptual loss to optimize the network, so as to obtain SR images with clearer details and better perceptual effects. Experiments demonstrate that in the quantitative comparison of the non-reference image quality assessment (NR-IQA) metrics like NIQE, BRISQUE and PIQE, as well as the intuitive visual effects of the generated images, compared with state-of-the-art models such as EDSR8-RGB, RCAN and RS-ESRGAN, our proposed model has obvious advantages.

Zucchini (Cucurbita pepo L.) is an important crash crop for producing seeds in Inner Mongolia, China. In August 2021, the harvest season of seed-producing zucchini, fruit rot symptom (cv. Jindi No.1) was found in the Wuyuan region. The incidence of infected fruits of zucchini ranged from 10% to 30% and symptom consisted in 4 to 5 cm diameter lesions where the fruit was in contact with the soil. Ten isolations from six symptomatic fruits were preliminary classified as Fusarium species based on its morphological characters in potato dextrose agar. Phylogenetic tree was constructed by concatenating TEF-1α and RPB2 gene and exhibited the isolates clustered together with the Fusarium solani f. sp. cucurbitae sequences. Pathogenicity tests revealed that two isolates caused over 3 cm diameter lesions on the fruits while negative-controls remained asymptomatic. The colonies reisolated from the leasions were morphologically identical to the original isolates, thus fulfilling Koch’s postulates. Results demonstrated that F. solani f. sp. cucurbitae was the causal agent of fruit rot observed in the field. To our knowledge, this is the first report of fruit rot of seed-producing zucchini caused by F. solani f. sp. cucurbitae in Inner Mongolia, China.

This paper addresses the problem of low accuracy of conventional channel estimation and signal detection in complex fields like mines; and the problem of replacing the deep receiver at the receiver side with a deep neural network requires a large amount of data for training and slow training time. Combining the receiver side with traditional communication knowledge, a channel estimation and signal detection method based on the joint ReEsNet and SDRNet under the mine is proposed. The detailed step is to use ReEsNet network for interpolation of conventional channel estimation. Then, on the basis of ReEsNet, the output data is channel equalized and pilots removed, and the previously processed data is input to SDRNet to perform signal recovery. In the complex mine environment, the MSE values are 2e-2 for LS, 6e-3 for MMSE, and 8.44e-5 for ReEsNet at the 1500th sample data for interpolation compared to the conventional channel estimation. the MSE of ReEsNet is the smallest and is closer to the real channel estimation. Compared with the proposed joint channel estimation and signal detection methods, fewer trainable parameters reduce 97% of the parameters compared to CCRNet and 84% of the parameters compared to CNNNet; their detection results, however, are not very different.

We used the Bootstrap ARDL method to test the relationship between the export trades, FDI and CO₂ emissions of the BRICS countries. We found that China's foreign direct investment and the lag one period of CO₂ emissions have a cointegration on exports. South Africa's foreign direct investment and CO₂ emissions have a cointegration relationship with the lag one period of exports, and South Africa's the lag one period of exports and foreign direct investment have a cointegration relationship with the lag one period of CO₂ emissions. But whether it is China or South Africa, these three variables have no causal relationship in the long-term. Among the variables of other BRICS countries, Russia is the only country showed degenerate case #1 in McNown et al. mentioned in their paper. When we examined short-term causality, we found that CO₂ emissions and export trade showed a reverse causal relationship, while FDI and carbon emissions were not so obvious. Export trade has a positive causal relationship with FDI. Those variables are different from different situations and different countries.

In this study, a cholera infection model with the bilinear infection rate is developed by considering the perturbation of the infection rate by the mean-reverting process. First of all, we give the existence of a globally unique positive solution for a stochastic system at arbitrary initial value. On this basis, the sufficient condition for the model to have an ergodic stationary distribution is given by constructing proper Lyapunov functions and tight sets. This indicates in a biological sense the long-term persistence of cholera infection. Furthermore, after transforming the stochastic model to an relevant linearised system, an accurate expression for the probability density function of the stochastic model around a quasi-endemic equilibrium is derived. Subsequently, the sufficient condition to make the disease extinct is also derived. Eventually, the theoretical findings are shown by numerical simulations. Numerical simulations show that the impact of regression speed and fluctuation intensity on stochastic systems.

River flood routing computes changes in shape of a flood wave over time as it travels downstream along a river. Conventional flood routing models, especially hydrodynamic models require high quality and quantity of input data such as measured hydrologic time series, geometric data, hydraulic structures and hydrological parameters. Unlike physically based models, machine learning algorithms, which are data driven models, do not require much knowledge about underlying physical processes and can identify complex nonlinearity between inputs and outputs. Due to the higher performance, less complexity, and low computation cost, novel machine learning methods as a single application or hybrid application were introduced by researchers to achieve more accurate and efficient flood routing. This paper reviews the recent application of machine learning methods in river flood routing.

In this study, Brillouin optical time-domain analysis (BOTDA) sensing technology was utilized for monitoring settlement in a similarity model of a highway subgrade. As contact winding cannot be used for an optical fiber that is buried directly in soil, uncoupling between. the fiber and the soil can occur. Thus, an optical-fiber-embedded beam (OFEB) was developed, and a method for measuring and calculating the beam deformation was proposed. A calibration test and a test on a similarity model of a subgrade were carried out to investigate the applicability and monitoring accuracy of the OFEB. It was concluded that the OFEB can accurately measure beam deflection, where the maximum relative error between measurements by the optical fiber and a displacement transducer was approximately 5%. The OFEB was embedded directly into a similarity model of a subgrade to monitor settlement. The deflection deformation of the OFEB was found to be close to the subgrade settlement over a certain settlement range with a relative error below 8.1%. Thus, the OFEB can be used to realize measure large-range distributed settlement in a subgrade. A numerical simulation was performed to identify appropriate beam dimensions and material design parameters, thereby extending the measurement range before decoupling of the OFEB and soil occurs. The enhancement of the measurement range and accuracy of the OFEB based on the preliminary experiments carried out in this study enables further investigation of settlement monitoring.

Monascus pigments (MPs) have been used as food colorants for several centuries in Asian countries and nowadays in the whole world via Asian catering. The MPs biosynthetic pathway has been well-illustrated, however, the functions of a few genes including mrpigH in the MPs gene cluster of M. ruber M7 are still unclear. In current study, mrpigH was disrupted in Δmrlig4ΔmrpyrG, a highly efficient gene modification system, using mrpyrG as a selection marker, and ΔmrpigHΔmrlig4ΔmrpyrG::mrpyrG and ΔmrpigHΔmrlig4ΔmrpyrG have been obtained. Subsequently, their morphologies, biomasses, MPs and citrinin (CIT) production were analyzed, respectively. These results have revealed that the deletion of mrpigH has significant effects on the morphology and growth of M. ruber M7. Moreover, compared with M. ruber M7, the yields of MPs and CIT were drastically increased and decreased in mrpigH mutants, respectively.

Microfinance institutions (MFIs) play an significant role in financial inclusion and poverty alleviation activities. A critical challenge facing MFIs is how on all to build its own capacity for sustainable and healthy development. By using the data from the pilot survey of 65 microcredit companies in Zhejiang of China, this paper explores the factors affecting MFIs activities by principal component analysis and analyzes the key Influencing factors and sustainable development performance with the analysis of variance and multi-regression model.The results indicate that four key factors of operational technology, external environment, financial condition and institution size have a significant positive effect on the economic sustainability performance of MFIs, while the adjusted institution size is insignificant positive effect on operational sustainability performance,which means that key factors of MFIs sustainability have a greater impact on economic sustainability performance than operational sustainability performance.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

Considering the significance of thermodynamic cycles in the global energy system, it is necessary to develop new general classes of thermodynamic cycles to relieve current energy and environmental problems. Inspired by the relationship between power cycles and refrigeration cycles, we realize that general classes of thermodynamic cycles should occur in pairs with opposite functions. Here we reverse class 1 heating cycles to obtain another new general class of thermodynamic cycles named class 2 heating cycles (HC-2s). HC-2s have two basic forms, and each contains six thermodynamic processes. HC-2s present the simplest and most general approach to utilizing the temperature difference between a medium-temperature heat source and a low-temperature heat sink to achieve efficient high-temperature heating. HC-2s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in the global sustainable energy system.

Thermodynamic cycles are not only the core concepts of thermal science, but also key approaches to energy conversion and utilization. So far, power cycles and refrigeration cycles have been the only two general classes of thermodynamic cycles. While diverse types of systems have been developed to perform thermodynamic cycles, no new general classes of thermodynamic cycles have been proposed. Based on the basic principles of thermodynamics, here we propose and analyze a new general class of thermodynamic cycles named class 1 heating cycles (HC-1s). Two basic forms of HC-1s are obtained by connecting six essential thermodynamic processes in the proper order and forming a thermodynamic cycle. HC-1s present the simplest and most general approach to utilizing the temperature difference between a high-temperature heat source and a medium-temperature heat sink to achieve efficient medium-temperature heating and/or low-temperature cooling. HC-1s fill the gaps that have existed since the origin of thermal science, and they will play significant roles in energy conservation and emission reduction.

Existing research concerning the effects of the sitting birth position during the second stage of labour on maternal and neonatal outcomes remains controversial, and there is a lack of studies to explore its effect on the childbirth experience. The objective of this study is to explore whether the sitting birth position would influence maternal and neonatal outcomes, as well as the childbirth experience reported by Chinese women using the Childbirth Experience Questionnaire (CEQ). A total of 296 women (including primiparous women and multiparous women) were enrolled in our study, and they were divided into the sitting position cohort (n=106) or the lithotomy position cohort(n=116). The study found that primiparous women in the sitting position cohort had a shorter duration of the second stage of labour, higher spontaneous vaginal birth rates, lower episiotomy rates and better childbirth experience (p<0.01). There was no significant difference for perineal lacerations, 2h-postpartum haemorrhage (P>0.05) between the two cohorts of primiparous women. After adjusting for confounding factors through multiple linear and logistic regression analyses, the results remained consistent with those reported above. No neonate in each cohort had Apgar scores at 1min and 5 min postpartum less than 7 or the Cord artery pH less than 7.00, regardless of parity. In addition, among multiparous women, there was no significant difference in any maternal and neonatal outcomes and women’s CEQ scores (p>0.05) between two cohorts. Based on the findings, we recommend that women could take the sitting birth position into account when giving birth for a positive childbirth experience, especially for primiparous women. The study could also serve as a reference for healthcare providers in the management of childbirth positions and the development of high-quality maternal care.

Hydrogen sulfide (H₂S) is a novel gasotransmitter, sucrose (SUC) is both cellular energy and signaling molecule. However, their signaling interaction in maize thermotolerance is poorly known. In this study, using maize seedlings as materials, metabolic and functional interaction of H₂S and SUC in maize thermotolerance was investigated. Data show that under heat stress survival rate and tissue viability were increased by exogenous SUC, while malondialdehyde content and electrolyte leakage were decreased by SUC, indicating SUC could upraise maize thermotolerance. Also, SUC-upraised thermotolerance was enhanced by H₂S, while weakened by inhibitor (propargylglycine) and scavenger (hypotaurine) of H₂S and SUC-transport inhibitor (N-ethylmaleimide). To figure out underlying mechanism of H₂S-SUC interaction-upraised thermotolerance, redox parameters in mesocotyls of maize seedlings were measured before and after heat stress. The data display that activity and gene expression of H₂S-metabolizing enzymes were up-regulated by SUC, whereas H₂S had no significant effect on activity and gene expression of SUC-metabolizing enzymes. Besides, activity and gene expression of catalase, glutathione reductase, ascorbate peroxidase, peroxidase, dehydroascorbate reductase, monodehydroascorbate reductase, and superoxide dismutase were reinforced by H₂S, SUC, and their combination under non-heat and heat conditions in varying degrees. Similarly, content of ascorbic acid, flavone, carotenoid, and polyphenol was increased by H₂S, SUC, and their combination, whereas production of superoxide radical and hydrogen peroxide level were impaired by these treatments to different extent. These results imply that the metabolic and functional interaction of H₂S and sucrose exists in the formation of maize thermotolerance through redox homeodynamics.

In this study, we discuss the thermospheric density response to the solar activity and QBO. By using the wavelet power spectrum method, the thermospheric density from 1967 to 2013 shows ~11-year period, semiannual and annual variations, while the seasonal variation is usually more significant under high solar activity conditions. Importantly, we investigate the possible link between the density and the QBO, with the aid of GAMDM model and different density residual method. As a result, the difference between the measured density and empirical model seemingly has QBO signal, but the ratio of them revels that the QBO signal does not exist in the thermospheric density. Comprehensively, we thought the stratospheric QBO cannot impact on the thermosphere, and more data and numerical modeling are needed for further validation.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

The biosynthesis of C27-29 sterols from their C30 precursor squalene involves C24-alkylation and removal of three methyl groups, including two at the C4 position. The two C4 demethylation reactions require a bifunctional enzyme known as 3β-hydroxysteroid dehydrogenase/C4-decarboxylase (3βHSD/D) that removes an oxidized methyl (carboxylic) group at C4 while simultaneously catalyzing the 3β-hydroxyl3-keto oxidation. Its loss-of-function mutations cause ergosterol-dependent growth in yeast and congenital hemidysplasia with ichthyosiform erythroderma and limb defect (CHILD) syndrome in humans. Although plant 3βHSD/D enzymes were well studied enzymatically, their developmental functions remain unknown. Here we employed a CRISPR/Cas9-based genome-editing approach to generate knockout mutants for two Arabidopsis 3βHSD/D genes, HSD1 and HSD2, and discovered the male gametophytic lethality for the hsd1 hsd2 double mutation. Pollen-specific expression of HSD2 in the heterozygous hsd1 hsd2/+ mutant not only rescued the pollen lethality but also revealed critical roles of the two HSD genes in embryogenesis. Our study thus demonstrated essential functions of the two Arabidopsis 3βHSD/D genes in male gametogenesis and embryogenesis.

To circumvent the thermodynamic limitation of the synthesis of oxazolidinones starting from 2-aminoethanols and CO2 and realize incorporation CO2 under atmospheric pressure, a protic ionic liquid-facilitated three-component reaction of propargyl alcohols, CO2 and 2-aminoethanols was developed to produce 2-oxazolidinones along with equal amount of α-hydroxyl ketones. The ionic liquid structure, reaction temperature and reaction time were in detail investigated. And 15 mol% [TBDH][TFE] (1,5,7-triazabicylo[4.4.0]dec-5-ene trifluoroethanol) was found to be able to synergistically activate the substrate and CO2, thus catalyzing this cascade reaction under atmospheric CO2 pressure. By employing this task-specific ionic liquid as sustainable catalyst, 2-aminoethanols with different substituents were successfully transformed to 2-oxazolidinones with moderate to excellent yield after 12 h at 80 oC. This three-component reaction running under atmospheric pressure proves to be a clever detour to avoid the thermodynamic issue in the synthesis of 2-oxazolidinones starting from 2-aminoethanols and CO2.

The separation and enrichment can be targeted to enrich the rare and precious metals in fly ash and reduce the cost of leaching and recovering of fly ash. Regarding their different properties, the single-component separation was used to obtain uncompleted burned carbon, glass microbeads, minerals, and other characteristic components from the ash. Also, the mineral composition of each component was analyzed by electron microscopy. The metal minerals were mainly concentrated in the mineral components. Besides, the electron probe micro-analysis shows that the Pt content in the minerals of fly ash was significantly correlated with the metal contents of Ni and Cu. After the obtainment of the characteristics of fly ash metal enrichment, the heavy minerals with Cu, Ni, Pt, Pd, and other target metal elements were enriched by gravity separation and flotation. The enrichment coefficients of Cu, Ni, Pt, and Pd were 1.45, 1.33, 1.90 and 1.60, respectively, and the recovery rates were 77%, 81%, 97% and 88% respectively. Since the yield of heavy minerals obtained by separation was 62.24%, it indicated the physical separation method could significantly reduce the cost of leaching and recovering of fly ash metal resources.

Prosthetic attack is a problem that must be prevented in the current finger vein recognition application. To solve this problem, a finger vein living detection system was established in this article. The system first captures short-term static finger vein video by uniform near-infrared lighting, segments the veins by Gabor filters with current removing, calculates the multi-Scale spatial-Temporal maps(MSTmap) from the selected vein blocks, and trains the MSTmaps in the proposed Light-ViT network for the liveness detection. The MS maps are used to extract the coarse feature and Light-ViT is used to refine the liveness feature and predict the liveness result. Light-ViT, featuring an enhanced L-ViT backbone as its core, is constructed by interleaving multiple MN blocks and L-ViT blocks. This architecture effectively balances the learning of local image features, controls network parameter complexity, and substantially improves the accuracy of liveness detection. The accuracy of the Light-ViT network is verified to be 99.63% on the self-made living / prosthetic finger vein video dataset. This proposed system can also be directly applied to the finger vein recognition terminal after the model lightweighting.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

Low-sodium salt substitute (LSSS) has the potential in regulating sodium and potassium intake and has been available in China market for years. However, its real-world use and impact to sodium\potassium intake is unclear. Baseline data of 4000 adult participants who participated in three similar-designed randomized controlled trails were pooled together for this study. Self-reported awareness and use of LSSS were collected using the uniform questionnaire, and the 24-h urinary sodium and potassium excretion was used to estimate their dietary intake. Mixed-effects models were developed to assess the relationship between LSSS and 24-h urinary sodium and potassium excretion. 32.0% of the participants reported awareness of LSSS and 11.7% reported its current use. After adjusting location, sex, age, and education, compared with the group of participants unaware of LSSS, participants who were aware but not using LSSS and those who were using LSSS had a lower 24-h urinary sodium excretion by –356.1(95% CI: –503.9, –205.9) mg/d and –490.6(95% CI: –679.2, –293.7), respectively (p&lt;0.001). No significant difference was found for 24-h urinary potassium excretion and sodium-to-potassium ratio among the three groups (p&gt;0.05). In conclusion, although associated with lower sodium intake, the awareness and real-world use of LSSS are still very low in China.

In this paper, we consider the formation of quantum black holes (QBHs) through a genuine quantum process. We treat particles at the Planck energy as QBHs. The Hawking temperature and entropy of QBHs are estimated. We also show that a QBH has a discrete energy spectrum. By analogy with supersymmetric theory, the mass of the superpartner of a QBH is estimated.

The segmentation of urban scene mobile laser scanning (MLS) data into meaningful street objects is a great challenge due to the scene complexity of street environments, especially in the vicinity of street objects such as poles and trees. This paper proposes a three-stage method for the segmentation of urban MLS data at the object level. The original unorganized point cloud is first voxelized, and all information needed is stored in the voxels. These voxels are then classified as ground and non-ground voxels. In the second stage, the whole scene is segmented into clusters by applying a density-based clustering method based on two key parameters: local density and minimum distance. In the third stage, a merging step and a re-assignment processing step are applied to address the over-segmentation problem and noise points, respectively. We tested the effectiveness of the proposed methods on two urban MLS datasets. The overall accuracies of the segmentation results for the two test sites are 98.3% and 97%, thereby validating the effectiveness of the proposed method.

Amylin, also known as islet amyloid polypeptide (IAPP), is a metabolic homeostasis-related hormone that is produced and released by the β cells of the pancreas, the same cells that produce insulin. Insulin-degrading enzyme (IDE) is a protease enzyme that plays an essential role in the breakdown and degradation of various peptides, including insulin and amylin. Direct binding & interaction between amylin and IDE is inextricably linked to the degradation of amylin, and research and development effort in this area is crucial to understand the potential therapeutic implications of disrupting the IDE-amylin interaction in the context of conditions where metabolic homeostasis needs to be regulated, such as diabetes and obesity. Here, this article incorporates currently available experimental complex structure of amylin and IDE, and delves deep into the interstructural biophysics underlying the binding interface of the two interacting partners. With a set of comprehensive structural biophysical analysis, this article identified an intriguing region of high electrostatic potential indicative of strong binding sites between the first N-terminal lysine (Lys1, K1) residue of amylin and Glu341 (E341) of IDE. This unique electrostatic hotspot presented herein paves the way for the rational design of drug-like small molecules that can selectively disrupt this interaction, offering a targeted therapeutic strategy for improved metabolic homeostasis, particularly for patients with diabetes and obesity.

Thrombosis has threatened human health in past decades. Bacillus nattokinase is a potential thrombolytic drug without side-effect and low cost and has been introduced into the consumer market as a functional food or dietary supplement. This review firstly summarizes the biodiversity sources and fermentation process of nattokinase, and systematically expounds the structure, cata-lytic mechanism and enzymatic properties of nattokinase; In view of the problems of low fermen-tation yield, insufficient activity and stability of nattokinase, this review discusses the heterologous expression of nattokinase in different microbial hosts, and summarizes the protein and genetic en-gineering progress of nattokinase-producing strains; Finally, this review summarizes the clinical application of nattokinase.

In the domain of drug discovery and design, the acquisition of precise structural and intermolecular Kd data for biological molecules is paramount. However, conventional methods for obtaining such data are often beset by challenges including high costs, time intensiveness, and inherent limitations in scalability and diversity. This article puts forward a high-throughput approach for in silico generation of structural and intermolecular binding affinity (Kd) data, which keeps exploring the uncharted territories of drug discovery & design by harnessing computational methodologies to synthetically generate diverse datasets. Through a meticulously designed workflow encompassing molecular structural modeling, structural biophysics-based calculations of intermolecular binding affinity (Kd), this innovative methodology transcends the constraints of traditional experimentation, offering a cost-effective, scalable, and efficient alternative. By simulating molecular interactions and binding interfaces and predicting binding affinities with reasonable accuracy, this approach not only expedites the drug development process but also enables the exploration of vast molecular space, thereby facilitating the discovery of novel therapeutics beyond conventional drug modality as a form factor. Moreover, the versatility of synthetic data extends beyond virtual screening and lead optimization, encompassing applications such as dataset augmentation, model validation, and benchmarking against experimental data. This article elucidates the conceptual underpinnings, methodological intricacies, validation strategies, and potential ramifications of in silico generated data, heralding a paradigm shift in drug discovery paradigms. By fostering synergy between computational and experimental research domains, this innovative approach promises to accelerate the pace of drug discovery, enhance the robustness of predictive models, and pave the way for transformative advancements in the entire pharmaceutical industry.

Aeroponics is a relatively new soilless culture technology, which may produce food in space limited cities or non-arable land with high water use efficiency. The shoot and root growth, root characteristics, mineral contents of two lettuce cultivars were measured in aeroponics, as compared with hydroponics and substrate culture. The results showed that aeroponics remarkably improved the root growth with a significant greater root biomass, root/shoot ratio, and several times higher total root length, root area and root volume. However, the greater root growth did not lead to a better shoot growth compared with hydroponics, due to the limited availability of nutrients and water. It can be concluded that aeroponics systems may be better for high value true root crops production. Further research is necessary to figure out the suitable pressure, droplet size, and misting interval in order to improve the continuously availability of nutrients and water in aeroponics, if it is used to grow crops like lettuce for harvesting above-ground parts.

Stratocumulus (Sc) is the most common cloud type in China. Sc clouds may or may not be accompanied by various types of precipitation that are representative of different macro- and microphysical characteristics. The finely resolved CloudSat data products are used in this study to quantitatively investigate the macro- and microphysical characteristics of precipitating and non-precipitating Sc (PS and NPS, respectively) clouds over Eastern China (EC). Based on statistical information extracted from the CloudSat data, Sc clouds are highly likely to occur alone, in association with liquid precipitation, or in association with drizzle over 25.65% of EC. The cloud bases of NPS clouds are higher than those of PS clouds, although the latter display higher cloud top heights and thicker cloud thicknesses. The spatial distributions of microphysical characteristics differ between PS and NPS clouds. The magnitudes of microphysical characteristics in NPS clouds are relatively small and decrease with height, whereas the magnitudes of microphysical characteristics in PS clouds are relatively large and peak in response to certain circulation patterns and over certain terrain. The variations in microphysical characteristics in Sc clouds with height and contoured frequency by altitude diagrams (CFADs) of radar reflectivity may indicate that different microphysical processes operate in PS and NPS clouds. In NPS clouds, hydrometeor particles accumulate by coalescence as they rise; once the particles are too large to be supported by updrafts, the cloud droplets form raindrops. In PS clouds, raindrops increase continuously in size via collision-coalescence processes as they fall. The levels between 2.5 and 3.0 km represent the space where particles grow most rapidly. Particles are affected by updrafts and accumulate at levels between 2.5 and 1.0 km as height decreases.

Particles are considered temporarily identical if the interchange of these particles does not cause any observable physical effects within a time interval Δt. An indistinguishability hypothesis is proposed for such particles, suggesting that two particles (or systems) with nearly the same degree of internal freedom will actually interchange under certain circumstances, thereby affecting the subsequent dynamics. This indistinguishability implies that, theoretically, it is possible to capture an elementary particle with extraordinarily large internal freedom by trading it for an isolated composite system of ordinary matter particles with almost the same total internal freedom as the large-freedom particle. Following this, the ordinary particles will instantly disperse into the environment, while the large-freedom particle will initially be captured and then gradually delocalized into the environment, an observable phenomenon. If this hypothesis is proven true in the future, it might provide a novel strategy for detecting dark matter particles.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

Since the launch of Protein Data Bank (PDB) in 1971, Cartesian coordinate system (CCS) has been the default approach to specify atomic positions in biomolecular experimental structures with X, Y and Z. In 2020, a local spherical coordinate system (LSCS) approach was proposed as an alternative to CCS, i.e., ρ, θ and φ. Recently, the continued application of deep learning technology in protein structure prediction (PSP) saw a leap forward in the accuracy of PSP, as evidenced by AlphaFold of Google’s DeepMind. However, there still is room for the improvement of the performances of PSP algorithms to date. Given that geometrically, CCS and LSCS are like the two sides of a coin, this short article puts forward a hypothesis that the time is now ripe to end the half-a-century burial of ρ, θ and φ in PDB, and use them as LSCS features for the design of novel PSP algorithms in future.

As of not long ago, understanding the administrative conduct of cells has been sought after through autonomous investigation of the transcriptome or the proteome. In view of the focal creed, it was commonly accepted that there exist an immediate correspondence between mRNA records and produced protein articulations. In any case, late examinations have demonstrated that the relationship among's mRNA and Protein articulations can be low because of different factors, for example, unique half lives and post record apparatus. In this manner, a joint investigation of the transcriptomic and proteomic information can give valuable experiences that may not be translated from singular examination of mRNA or protein articulations. This article audits the current significant methodologies for joint investigation of transcriptomic and proteomic information. We order the various methodologies into eight primary classes dependent on the underlying calculation and last investigation objective. We further present analogies with different spaces and talk about the current exploration issues around there.

Examining the soil microbiome structure has a great significance in exploring the mechanism behind plant growth changes due to maize (Zea mays L.) and soybean (Glycine max Merr.) crop rotation. This study explored the effects of soil microbial community structure after soybean and maize crop rotation by designing nine treatments combining three crop rotations (continuous cropping maize or soybean; and maize after soybean) with three fertility treatments (organic compound fertilizer, chemical fertilizer, or without fertilizer). Soil was sampled to 30 cm depth the second year at approximately the middle of the growing season, and was analyzed for physical, chemical, and phospholipid fatty acid (PLFA) profiles. Bacteria was found to be the predominant component of soil microorganisms, which mainly contain the PLFAs i15:0, 16:1 ω 7c, 16:0, 10Me16:0, and 18:1 ω 7c. The concentration of soil gram-negative bacteria from the soybean and maize rotation was less than in soybean continuous cropping when organic fertilizer was applied to both. Crop rotation reduced the percentage of fungi in the soil, among which the effect of organic compound fertilizer application was significantly reduced 24%. The combined crop rotation with organic fertilizer can reduce maximum the percentage of fungi/bacteria. In addition, the content of soil aggregate and organic matter had great influence on gram-positive bacteria and actinomyces, and soil pH had a greater impact on other fungi.

To solve a series of major problems, such as the singularity before the Big Bang, the inflation of the early universe and the accelerating expansion of the present universe, this series of studies start with super gravity, dark energy and dark matter, go beyond the surface of a lot of observation data, and systematically reveal the arche-internal mechanism of all things, to establish the arche-unity of physics, and give a natural and reasonable explanation. At present, there are at least three basic pathways that are leading our research field to repulsion against gravitation, quantum repulsion against quantum gravitation and high-dimensional superrepulsion against high-dimensional supergravity, that is, the research on the accelerating expansion mechanism of the current universe, the research on the dynamic mechanism of the early cosmic inflation, and the research on the rebound mechanism near the singularity before the Big Bang. In this series of studies, the arche problem of everything is always placed under the extreme environmental conditions of the initial universe, the starting point of scientific logic is closely combined with the starting point of the universe history, the pseudo vacuum energy considered by the inflationary universe model, the Higgs field predicted by the standard physical model and the dark energy speculated by the observational cosmology are reduced to the positive energy system with strong negative pressure, and they are reduced to the repulsion (all the resistance to gravity) that forms a conjugate relation with gravity. In our opinion, dark energy and dark matter are essentially at the level of quantum gravity and quantum repulsion. Therefore, we not only consider the conventional quantum effect and non commutative quantum effect, but also further consider the arche-conjugate effect and the cluster resonance-at-cofrenquence effect. For noncommutative space-time, we put forth the ultimate supersymmetry, the arche-conjugation and the cluster resonance-at-cofrenquence. A relatively complete natural mechanism forms such an important inference: the closer they get to Planck scale, the stronger the conventional quantum effect, non commutative quantum effect, arche-conjugate effect and co-frequency resonance effect are. In the high-dimensional space-time (the 11 dimensional hyperspace compactly reduced to M 4 × N r ), corresponding to the introduction of supergravity with the supersymmetry between the graviton and the gravitino, we put forth the superrepulsion with the supersymmetry between the repulsion and the repulsitino, and establish the arche-conjugate relationship between the high-dimensional supergravity and the high-dimensional superrepulsion. Therefrom, we propose a basic inference that can be promoted to the principle of hyperholography of high-dimensional universe (or multiuniverse): in a parallel universe formed by mutual coupling and holographic correspondence between the P universe dominated by negative pressure (high-dimensional superrepulsion and quantum repulsion of accumulating positive energy, mainly composed of dark energy) and the N universe dominated by positive pressure (high-dimensional supergravity and quantum gravity of accumulating negative energy, mainly composed of dark matter), there is a correspondence between the small-scale physics (ultraviolet cutoff) of the P universe and the large-scale physics (infrared cutoff) of the N universe, while there is a correspondence between the large-scale physics (ultraviolet cutoff) of the P universe and the small-scale physics (infrared cutoff) of the N universe. In the new research paradigms set in this series, the arche-conjugation between the high-dimensional supergravity and the high-dimensional super repulsion, as well as between the quantum gravity and the quantum repulsion, is higher than the supersymmetry, so it becomes the core concept of the new theory. The arhce-unity of physics is a super unity that transcends the grand unification of four basic interaction, which is formed between high-dimensional supergravity (related to dark matter) and high-dimensional superrepulsion (related to dark energy), between quantum gravity (related to dark matter) and quantum repulsion (related to dark energy). From the basic component point of view, before or after the big bang, the gravitons and repulsons are coupled together, the negative energy contraction dominated by the positive pressure and the positive energy expansion dominated by the negative pressure work alternately, forming the arche-conjugate pulsaton of neither the point particle nor the linear superstring. Under the big unified framework of quantum gravitational field and quantum repulsive field, this series of work comprehensively expands the general relativity and loop quantum ring gravitation theory, sets up the quantum repulsive field equation corresponding to the quantum gravitational field equation, and then establishes the quantum hedge-unified field equation describing the interaction of quantum gravitational field and quantum repulsive field; On this basis, the quantum repulsive universe equation corresponding to the quantum gravitational universe equation is established, thus a set of new equations describing the expansive universe with quantum hedge-unified field are established. On the one hand, scalar disturbance is considered as the exhibition of repulsive effect, on the other hand, tensor disturbance is considered as the exhibition of gravitational effect. In the initial stage of the big ripping, due to the mutual restraint of quantum repulsion and quantum gravity, the scalar and tensor perturbations are not obvious. However, at the end of the big ripping, the scalar and tensor perturbations are very significant, and there is a large power spectral exponential run. Between particle physics and cosmology, we improve and expand the path integral of quantum gravity, create the path integral of quantum hedge-unified field, and set up the basic equation of quantum cosmic-synergetic dynamics, and then establish the basic equation of quantum-cosmic paradigm dynamics. Thus we put up the operator distribution function and its dynamic equation of the quantum arche- pulsaton, and finally use the Wigner-Ville distribution as a non-linear time-frequency distribution to establish the Wigner joint-distribution of quantum-conjuagted pulsation function, so as to analyze the arche of all things with three evolutionary forms: quantum chaotic-pulsaton, quantum quasi-spherical pulsaton and quantum spherical-pulsaton. In this series of work, the mechanism to avoid the singularity of the universe is put forward fundamentally, and the dark energy and dark matter are explained through new mechanisms and effects at the level of quantum gravity. Between particle physics and cosmology, we improve and expand the path integral of quantum gravity, establish the path integral of quantum hedge-unified field, thus establish the basic equation of quantum cosmic-synergy dynamics, and then establish the basic equation of quantum cosmic-paradigm dynamics. Thus the covariant gravitational mass and the covariant inertial mass formed by the ultra-synergy between particles and the universe are presented, and the equivalence hypothesis on the covariant non-inertial system which can be elevated to the basic principle, is presented. Based on this hypothesis, a systematic calculation and analysis of binary stars composed of neutron stars and black holes are made. The master equation, variance and Fokker-Planck equation for the birth-death and migration of a large number of particles are established between binary stars composed of neutron stars and black holes.

The phenomenon of ordered self-assembly on solid substrates is a topic of interest in both fundamental surface science research and its applications in nanotechnology. The regulation and control of two-dimensional (2D) self-assembled supra-molecular structures on surfaces have been realized through applying external stimuli. By utilizing scanning tunneling microscopy (STM), researchers can investigate detailed phase transition process about self-assembled monolayers (SAMs), providing insight into the interplay between intermolecular weak interactions and substrate-molecule interactions, which govern the formation of molecular self-assembly. This review will discuss the structural transition of self-assembly probed by STM in response to external stimuli and provide state-of-art methods such as tip induced confinement for the alignment of SAM domains and selective chirality. Finally, we discuss the challenges and opportunities in the field of self-assembly and STM.

Histidine is an essential amino acid with significant implications in human growth and neuromodulation. Its concentration within cells, when either elevated or reduced, can indicate different diseases. While various methods exist to measure increased histidine levels, there remains a significant lack of sensors capable of actively responding to histidine deficiency within cells and releasing strong signals. In this study, we exploited the high induction levels of the his operon in S. Typhimurium SL1344, a histidine auxotroph, within a histidine-deficient environment, to develop a specific bacterial sensor with sensitivity towards low histidine concentrations. The SL1344-pGEX sensor, with a high copy number, exhibited remarkable sensitivity and selectivity to histidine in the range of 0 to 50 μM. Notably, even a minute addition of histidine (approximately 2.5 μM) to the M9 medium led to observable fluorescence reduction, rendering it highly suitable for monitoring histidine-deficient cellular environments. This bacterial fluorescence sensor holds great potential for detecting changes in intracellular histidine concentrations during pathogenic bacterial infections and for assessing the impact of drugs on cellular metabolism.

: The stability of semiconductor catalysts is a very important property in the field of catalytic reactions. Materials necessitate resistance to mechanical abrasion and chemical erosion for better overall performance. In this work, high crystallinity BiOCl nanosheets were prepared by a simple hydrothermal method. The photocatalysts demonstrate full UV light absorption ability and excellent photocatalytic norfloxacin degradation performance. 84 % of highly toxic norfloxacin were photocatalytically eliminated within 180 min. The internal structure and surface chemical state of BiOCl were analyzed by SEM, TEM, Raman, FTIR, UV-vis, XPS, and other techniques. Such high crystallinity makes BiOCl molecules closely arranged and the molecular chains strongly connected, thus exhibiting a high level of photocatalytic stability and recyclability.

For the symmetrical mixture model and mixture test area, the lattice point set is used to partition, and then the corresponding test statistics can be constructed. In this paper, we first proposes the partition methods under the lattice point sets and obtains several sub-simplexes without common interior points. Furthermore, we present the method for constructing a uniform design on the simplex using the center points of these sub-simplexes. The designs satisfy the uniformity of maximum distance deviation and provide good results for the mean square error deviation. Finally, the uniformity test on the mixture region is considered and illustrated by examples.

Crop disease classification has always been a critical and persistent problem in the field of agricultural and forestry sciences, where often we do not have access to a sufficient number of samples to know the distribution of real-world samples. How to make full use of the existing data is the starting point of our thinking. To address this problem, this paper proposes a supervised image augmentation method Negative Contrast, which uses the contrast images of existing disease samples after removing disease areas as negative samples for image augmentation when samples are relatively scarce. Numerous experiments have shown that several classical models using this augmentation method have improved in disease classification of four crops, rice, wheat, corn, and soybean, with a maximum accuracy improvement of 30.8%. In addition, the comparative analysis of attentional heat map shows that the model using Negative Contrast is more accurate and intense on the area of interest of diseases, and thus reflects better generalization ability in real-world disease classification. Our dataset and codes can be found in https://www.kaggle.com/datasets/w970704112/corn-wheat-rice-soybean and https://github.com/hiter0/contrastaug .

To address the problem of limited fault diagnosis accuracy in oil-immersed on-load tap changers (OLTC), this paper introduces a novel fault diagnosis method that combines the analysis of mechanical vibration signals and high-frequency current signals. The proposed approach aims to enhance the accuracy of fault diagnosis. To begin, an experimental platform is constructed to simulate the OLTC contact. Mechanical vibration signals and high-frequency current signals are collected from the testing platform under various operating states. These signals are then subjected to wavelet packet transform for denoising, followed by correlation analysis to capture the relationship between signals in different states. Based on these preliminary steps, the features of the signals are extracted and analyzed using ensemble empirical mode decomposition and the Hilbert-Huang transform. Subsequently, a support vector machine (SVM) is employed to analyze both the mechanical vibration signal and high-frequency current signal, enabling the classification of the OLTC contact state. The results demonstrate that the combination of characteristic analysis of mechanical vibration signals and high-frequency current signals provides a more comprehensive reflection of the actual OLTC contact state under different conditions. Through the SVM classification, the error between the predicted values and real values of the two types of signals remains below 10%, validating the efficiency and feasibility of the proposed method for fault diagnosis of OLTC contacts. These research findings serve as a reliable foundation for the diagnosis of operational states of on-site oil-immersed on-load tap changers, offering valuable insights for practical applications.

Low separation efficiency of photogenerated carriers and inefficient utilization of visible light limit the application of g-C3N4 nanosheets (CNNs) in the field of photocathodic protection (PCP). Therefore, this work considered indium zinc sulfide (ZnIn2S4, ZIS) as a visible photosensitizer and an electronic donor to promote its PCP performance. ZIS nanolayers with nano-leaf structures were fabricated on CNNs by a simple hydrothermal method. The synthesized 30% ZIS@CNNs composites significantly enhanced the PCP performance for 316 stainless steel (SS) compared with pure CNNs. Under visible light illumination, the 30% ZIS@CNNs photoelectrode exhibited the largest photoinduced current density of 17.30 μA cm−2 and a photoinduced potential drop of 0.37 V, which was approximately 4 and 7.5 times higher than that of pure CNNs, respectively. The improved protection performance may be attributed to the significant increase in visible light absorption and the great enhancement in the separation efficiency of

Endoplasmic reticulum (ER) stress triggers a series of signaling and transcriptional events termed the unfolded protein response (UPR). Severe ER stress is associated with the development of fibrosis in different organs including lung, liver, kidney, heart, and intestine. ER stress is an essential response of epithelial and immune cells in the pathogenesis of inflammatory bowel disease (IBD) including Crohn’s disease. Intestinal epithelial cells are susceptible to ER stress-mediated damage due to secretion of a large amount of proteins that are involved in mucosal defense. In other cells, ER stress is linked to myofibroblast activation, extracellular matrix production, macrophage polarization, and immune cell differentiation. This review focuses on the role of UPR in the pathogenesis in IBD from an immunologic perspective. The roles of macrophage and mesenchymal cells in the UPR from in vitro and in vivo animal models are discussed. The links between ER stress and other signaling pathways such as senescence and autophagy are introduced. Recent advances in the understanding of the epigenetic regulation of UPR signaling are also updated here. The future directions of development of the UPR research and therapeutic strategies to manipulate ER stress levels are also reviewed.

Mesoporous silica nanoparticles (MSNs) can be used as carrier materials for the controlled release of pesticides while reducing their negative environmental impact. In this study, we screened an active ingredient, p-cymene (PC), with an excellent inhibitory effect on rice bacterial blight. Subsequently, the PC was successfully loaded onto MSNs via physisorption(PC@MSNs). PC@MSNs, characterized by a regular spherical shape, smooth surface, and an MSN average size of 262.9 nm, achieved an 8.6 % drug loading capacity. The release kinetics of the PC from the PC@MSNs demonstrated a sustained release (288 h) pattern influenced by drug diffusion. The efficacy of the PC@MSNs against Xanthomonas oryzae pv. Oryzae paralleled those of PC. Acute toxicity assays re-vealed that the PC@MSNs were less toxic to aquatic life (LC50=257.867 mg/L) and that the formu-lation showed no adverse effects on rice seedling growth. In summary, these results suggest that PC@MSNs can broaden PC's application scope in managing rice diseases.

Insulin icodec of Novo Nordisk is a novel long-acting insulin analogue that exhibits an extended duration of action, providing a promising treatment option for individuals with diabetes. It has been reported that the incorporation of fatty acid moieties into insulin icodec plays a crucial role in its prolonged action, as these fatty acid chains facilitate the formation of stable hexameric structures, thereby delaying insulin absorption and promoting sustained release. Yet, the underlying biophysics still is elusive of the roles of the three site-specific mutations (Y14A\_E, Y37B\_H, F46B\_H) of insulin icodec in its prolonged activity. Thus, through a comprehensive structural and biophysical analysis of the insulin (both native and icodec) structures bound to its receptor, this article delves deep into the biophysics underlying the molecular design of insulin icodec, and identified a delicate biophysical mechanism through which two missense mutations of insulin icodec (Y37B\_H and F46B\_H) contribute to its prolonged duration of action. Overall, this structural and biophysical investigation provides valuable insights into the mechanisms underlying the relationship between three site-specific mutations and prolonged duration of action of insulin icodec, while understanding these modifications at a structural and biophysical level can aid in the rational design of future long-acting insulin analogues, offering further enhanced therapeutic options for diabetic patients.

Instead of tissue-based detection, blood-based tumor mutation burden (bTMB) is becoming an alternative promising alternate to predict the response of immune checkpoint inhibitor in cancers, especially non-small-cell lung cancer. Although bTMB is more convenient and less invasive, many evidences identified its limited predictive ability and less accurate discrimination of candidates to receive immunotherapy. Several ways of adjustments have been applied to improve the clinical usefulness of bTMB, such as setting restriction for threshold of allele frequency to exclude some unwanted mutations. But many questions remained to be explored such as the number and the type of mutations that should be incorporated into the bTMB estimation. This viewpoint summarized the current attempts to modify bTMB and provided granular aspects that have implications for further enhancement of bTMB’s predictive capability.

This paper studies the mechanism of how China’s state-owned enterprise (SOEs) reform can influences economic growth, and distinguishes the capital efficiency between state-owned and private enterprises. The results show that: 1) the capital allocation efficiency among state-owned enterprises is lower than private enterprise due to an insufficiently released productivity of state-owned enterprises; 2) although with a higher capital allocation efficiency, the improvement of technology progress of private enterprises at a much slower pace compared to its rapidly increasing share in China’s economy. In case of poor allocation with private sector, blindly reforming ownership of state-owned enterprises cannot effectively alleviate the problem of efficiency losses. State-owned enterprise reform can boost economic growth by increasing capital marginal output, improving capital dynamic allocation efficiency, promoting TFP growth and exerting external spillovers on other firms. At present, China is exploring the endogenous power of economic growth, improving the market institutions and promoting the state-owned enterprises reform with positive and steady pace. By properly re-allocation SOEs into the private sector, which has significant influence on improving economic efficiency and promoting sustained economic growth.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

Converting natural language into machine language that can be recognized by distributed systems is the core challenge of intelligent interactive interfaces and human-machine dialogue systems. The human-machine interface interaction of large distributed SCADA measurement and control system is tedious and the operation and maintenance cost is high, so it is significant to design an intelligent natural language interaction interface for distributed measurement and control system. In this paper, we design the intermediate language format of SCADA system, i.e., Key-value logic form, and then formulate the Text2SCADA framework and propose the TICS algorithm and SDPA algorithm, the former adopts the keyword extraction and cosine similarity optimization algorithm to complete the structured extraction of natural language for basic natural language instructions, and the latter adopts the keyword extraction and cosine similarity optimization algorithm to complete the structured extraction of natural language for relatively The latter one adopts the algorithm of dependent syntactic analysis for the structured representation of natural language instructions with relatively complex natural language instructions. Based on the above algorithms, a lightweight information extraction model based on DGCNN and probabilistic graph ideas is constructed, aiming to enhance the scientific generalization ability of the framework on unknown instruction sets. The experimental results show that the proposed intelligent natural language interface can better solve the human-machine interface interaction problem of distributed SCADA measurement and control system. The average accuracy, recall and F-value of instruction parsing reach 89.27\%, 89.28\% and 89.27\%, respectively. The average response time is 1.593 s. Especially, it provides a more convenient means of interaction for industrial and agricultural information control.