Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

This study investigated and classified typical structures in rural village and analyzed the vulnerability of various typical types of structures. Based on the statistics of earthquake damages with magnitudes above 5 from 1996 to 2013 in China, the damage matrixes of different types of structures in rural village are obtained. And The vulnerability index and the vulnerability equation of structure are crucial to assess the earthquake losses of typical structures under different magnitudes earthquakes. According to the seismic loss of different types of structures under different earthquake magnitudes, there are possible to improve the seismic resilience of the buildings in rural village. Moreover, the regional vulnerability is analyzed by β probability distribution function, and the comprehensive seismic performance index of different types of agricultural buildings in the region is obtained. The main research is to predict the loss of different types of structures under different earthquake magnitudes in the future, and to provide technical support for different types of building in rural village reinforcement.

Dryland winter wheat in Loess Plateau is facing yield reduction due to shortage of soil moisture and delayed sowing time. Field experiment was conducted at Loess Plateau in Shanxi Province, China from 2012 to 2014, to study the effect of subsoiling and conventional tillage and different sowing dates on the soil water storage and contribution of N accumulation and remobilization to yield of winter wheat. The results showed that subsoiling significantly improved the soil water storage at 0-300 cm depth, improved the number of tillers and pre-anthesis N translocation in various organs of wheat and post-anthesis N accumulation, eventually increased the yield up to 17-36%. Delaying sowing time had reduced the soil water storage at sowing and winter accumulated temperature by about 180˚C. The contribution of N translocation to grain yield was maximum in glume+spike followed by in leaves and minimum by stem+sheath. In addition a close relationship was found between the N accumulation and translocation and the soil moisture in the 20-300 cm. Subsoiling during the fallow period and the medium sowing date was beneficial for improving the soil water storage and increased the N translocation to grain, thereby increasing the yield of wheat, especially in dry year.

To accurately identify high-quality functional wood with superior mechanical properties and enhance its durability, it is imperative to understand the relationships between the physical and mechanical attributes of diverse wood types. Presently, there exist issues related to accuracy, efficiency, and differentiation in studying these performance correlations. The Liang Kleeman (L-K) information flow theory, a causative analytical approach rooted in fundamental physics principles, offers swift computational capabilities. Furthermore, the coefficient of variation in L-K information flow quantitatively gauges the intensity of causal effects. Therefore, this article adopts a causal artificial intelligence perspective and introduces a wood performance analysis method based on L-K information flow.This study focuses on four Chinese fir varieties, including fast-growing Chinese fir (YKS), red heart Chinese fir (CSH, XXH), and iron heart Chinese fir (XXT). By computing and comparing variation coefficients of L-K information flow for various physical properties and their impact on mechanical properties, causal relationships between these properties are elucidated. These findings are then applied to predict wood mechanical properties, achieving a remarkable maximum accuracy of 90%.In the future, these findings will prove invaluable for the selection of high-quality wood and for improving the manufacturing process to prolong the service life of functionalized wood.

ACE2, the putative receptor for the novel coronavirus (2019-nCoV), played an important role in cell entry of 2019-nCoV. However, it is not yet clear what cell types within the human body express ACE2. Here, a systematic analysis was undertaken using published single cell datasets. In total, our study analyzed 229652 cells, from five different organs, derived from 88 donors. The top ACE2 expressing cells include proximal tubule cells in the kidney and enterocytes in the intestine. Other major ACE2 expressing cells in the kidney include podocytes, intercalated cells and endothelial cells. Our results offer a comprehensive atlas of ACE2 expression at the single cell level and unravel the enormous potential targets of 2019-nCoVinfection beyond the lung.

Breast cancer is one of the most common types of malignant tumors worldwide and the leading cause of cancer-related deaths in women. According to the latest report from the World Health Organization, breast cancer has surpassed lung cancer, becoming the most diagnosed cancer globally. Herein, a systematic, quantitative, and visual analysis of the scientific achievements in natural products research and development for breast cancer over the past 30 years is presented. The study utilizes bibliometric and knowledge graph visualization techniques to analyze the trends, co-occurrence of keywords, cooperative networks, cited literature, and research hotspots in the field. The analysis shows that breast cancer natural drug development involves mutual cooperation between multiple countries, with China, the United States, and India being the most active players. Pharmacology is the discipline with the largest number of articles published in nearly 30 years. The study also reveals that the extraction of drugs from organisms and their metabolites is an important direction in the current development of anticancer drugs. The development of natural medicines for breast cancer together with the mining of genetic knowledge play an important role in treating human breast cancer. The research presented here provides insights into the current state of natural product research and development for breast cancer, and highlights the need for strengthening mutual communication and cooperation between countries and scientific research institutions to enhance the development of breast cancer treatment technologies and natural medicines.

Manual measurement of rock discontinuities is time-consuming and subjective according to the experience of the surveyor. This work proposes a three-dimensional laser scanning-based method for the semi-automatic identification of rock discontinuities. Multisite cloud scanning is performed with real-time kinematic (RTK)-assisted orientation to estimate the rock fracturing degree; then, discontinuity orientations are extracted with the man–machine interactive method or automatic method. The proposed method was applied to actual examples to illustrate its accuracy at identifying rock discontinuities. The sensitivity of the identification accuracy to different parameters was investigated.

Warming-induced drought stress and El Nino associated summer precipitation failure are responsible for increased forest fire intensities of tropical and temperate forests in Asia and Australia. However, both effects are unclear for boreal forests, the largest biome and carbon stock over land. Here we combined fire frequency, burned area and climate data in the Altai boreal forests, the southmost extension of Siberia boreal forest into China, and explored their link with ENSO (El Nino and South Oscillation). Surprisingly, both summer drought severity and fire occurrence have shown significant (P<0.05) teleconnections with La Nina events of the previous year, and therefore provide an important reference for forest fire prediction and prevention in Altai. Despite a significant warming trend, the increased moisture over Altai has largely offset the effect of warming-induced drought stress, and lead to an insignificant fire frequency trend in the last decades, and largely reduced burned area since the 1980s. The reduced burned area could also benefit from the fire suppression efforts and greatly increased investment in fire prevention since 1987.

Vibration problems have become one of the most important factors affecting robot performance. To this end, a terminal residual vibration suppression method based on joint trajectory optimization is proposed to improve the accuracy and stability of robot motion. Firstly, based on the characteristics of the friction nonlinearity due to joint coupling and physical feasibility of dynamic parameters, a semidefinite programming method is used to identify dynamic parameters with actual physical meaning, thereby obtaining an accurate dynamic model. Then, based on the result of the residual vibration time domain analysis, a joint trajectory optimization model with the goal of minimizing joint tracking error is established. The Chebyshev collocation method is used to discretize the optimization model. The dynamic model is used as the optimization constraint, and barycentric interpolation is used to obtain the optimized joint motion trajectory. Finally, industrial robot experiments prove that the vibration suppression method proposed in this article can reduce the maximum acceleration amplitude of residual vibration by 62% and the vibration duration by 71%. Compared with the input shaping method, the method proposed in this paper can reduce the terminal residual vibration more effectively and ensure the consistency of running time and trajectory.

The α-glucosidase inhibitor is of interest to researchers due to its association with type-II diabetes treatment by suppressing postprandial hyperglycemia. Hesperidin is a major flavonoid in orange fruit with diverse biological properties. This paper evaluates the effects of hesperidin on α-glucosidase through inhibitory kinetics, fluorescence quenching, and molecular docking methods for the first time. The inhibition kinetic analysis showed that hesperidin reversibly inhibited the α-glucosidase activity with an IC50 value of 18.52 M and the inhibition was performed in an uncompetitive type. Fluorescence quenching studies indicated that the intrinsic fluorescence of α-glucosidase was quenched via a static quenching process and only one binding site was present between hesperidin and α-glucosidase. The interaction between them was spontaneous and mainly driven by hydrogen bonds as well as hydrophobic forces. Furthermore, molecular docking results suggested that hesperidin might bond to the entrance or outlet part of the active site of α-glucosidase through a network of five hydrogen bonds formed between hesperidin and the four amino acid residues (Trp709, Arg422, Asn424, and Arg467) of ?-glucosidase and hydrophobic effects. These results provide new insights into the inhibitory mechanisms of hesperidin on α-glucosidase, supporting the potential application of hesperidin-rich orange product as a hypoglycemic functional food.

Background: Many randomized controlled trials (RCTs) and systematic reviews (SRs) on acupuncture treatment for post-acute stroke dysphagia have been published. Due to conflicting results an overview of SRs to summarize and assess the quality of this evidence to determine whether acupuncture is effective for this disease was conducted. Methods: Seven databases were searched for SRs and/or Meta-analysis of RCTs and quasi-RCTs on acupuncture for post-acute stroke dysphagia. Two authors independently identified SRs and meta-analyses, collected data to assess the quality of included SRs and meta analyses according to the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) and the revised Assessment of Multiple Systematic Reviews (AMSTAR 2). Results: 31 SRs were identified. Quality of 22 SRs was critically low, 5 SRs were low, and 4 Cochrane SRs were moderate when evaluated by AMSTAR2. 17 SRs reported 85.2-96.3% items of PRISMA. Five SRs included explanatory RCTs, 16 SRs included pragmatic RCTs, and 10 SRs included both. Conclusion: Currently evidence on the effectiveness of acupuncture on post-acute stroke dysphagia is low quality. Type of study appeared to have no direct influence on the result, but the primary outcome measures showed a relationship with the quality of SRs. High quality trials with large sample sizes should be the focus of future research. PROSPERO REGISTRATION NUMBER: CRD42019134163

Macrobrachium rosenbergii is a valuable freshwater prawn in Asian aquaculture. In recent years, a new symptom that was generally called as ‘white head’ caused high mortality in M. rosenbergii farms in China. Samples of M. rosenbergii, M. nipponense, Procambarus clarkii, M. superbum, Penaeus vannamei, and Cladocera from a farm suffering from ‘white head’ in Jiangsu Province were collected and analyzed in this study. Pathogen detection showed that all samples were positive for Shrimp hemocyte iridescent virus (SHIV). Histopathological examination revealed dark eosinophilic inclusions and pyknosis in hematopoietic tissue, hepatopancreas and gills of M. rosenbergii and M. nipponense. Blue signals of in situ DIG-labeled LAMP (ISDL) appeared in hematopoietic tissue, hemocytes, hepatopancreatic sinus, and antennal gland. TEM of ultrathin sections showed a large number of SHIV particles with a mean diameter about 157.9 nm. The virogenic stromata and budding virions were observed in hematopoietic cells. Quantitative detection by TaqMan probe based real-time PCR of different tissues in natural infected M. rosenbergii showed that hematopoietic tissue contained the highest SHIV load with a relative abundance of (25.4±16.9)%. Hepatopancreas and muscle contained the lowest SHIV load with a relative abundance at (2.44±1.24)% and (2.44±2.16)%, respectively. Above results verified that SHIV is the pathogen causing ‘white head’ in M. rosenbergii, and M. nipponense and Pr. clarkii are also the susceptible species of SHIV.

The meniscus is a meniscus-shaped fibrocartilage tissue located between the femur and tibia，it is mainly composed of meniscus cells and related extracellular matrix.The synovial limbus area of the knee joint capsule near the meniscus is divided into red areas with rich blood vessels and white areas with less blood supply according to the distribution of blood vessels,there is a transition zone called the red and white zone between the two;Red zone has better self-repair ability,The injury in this area can be treated by conservative treatment or surgical suture;Once the white area of the meniscus is torn and involves the free edge area,It is often necessary to partially remove the damaged meniscus.When most of the entire meniscus is severely torn and involved,not only the course of the disease is very long, but it cannot be repaired by sutures,Often a subtotal or total meniscus resection is required,whether it is a partial meniscus resection, a subtotal meniscus resection or a complete resection.In the later period, it may cause quadriceps atrophy and osteoarthritis (OA）.OA is a refractory multi-system disease,involve the patient’s peripheral joints,it has high disability and teratogenicity, and is very harmful to human health.Chondrocyte pyrolysis, degradation, and inflammation play a vital role in the destruction of OA articular cartilage and chondrocyte apoptosis.Meniscus stem cells have strong proliferation and differentiation ability,has become one of the hot spots in the field of meniscus repair,this article studies the role of meniscal stem cells in the development of OA.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

Physical inactivity is a well-known risk factor for various non-communicable diseases (NCDs). Sufficient physical activity (PA) is essential for the prevention of NCDs and thus it is imperative to study the current status of PA and its influencing factors among rural residents in China. A population-based survey was conducted in rural areas of Shandong, Shanxi and Yunnan Provinces using a stratified random sampling method. The International Physical Activity Questionnaire Short Form (IPAQ-S) was used to collect the data on PA. A total of 3780 rural residents participated in the survey. The result showed that 22.2% of rural residents were physical inactivity. The proportion of rural residents reporting practice of physical exercise was 54.4%. The most frequently performed physical exercise was walking/brisk walking(78.3%).Binary logistic regression analyses showed that being female, people at age between 15 to 34 years or 60 years old and above, employees of governmental departments/retirees, school students, the unemployed, people with NCDs were risk factors of PA and ethnic minority groups,smoking and alcohol consumption were risk factors of physical exercise. Health promotion programme aiming at increasing people’s PA in rural China is needed and it should focus on the populations groups of the female, people at age 60 years and above ,school students, the unemployed, and people with NCDs.

The Myb family of transcription factors (TFs) is a large and functionally diverse group found in all eukaryotes, but its role in fungi remains poorly understood. Here, we characterized a Myb family TF called MoMyb13 in the rice blast fungus, Magnaporthe oryzae. MoMyb13 has two Myb domains and has orthologues only in ascomycete fungi. Localization experiments confirmed that MoMyb13 is located in the nuclei, as expected for a TF. Phenotypic analysis showed that MoMyb13 mutants exhibited reduced growth, whitened colony appearance and no conidia formation. Importantly, these mutants completely lost pathogenicity, despite being able to form appressoria at their hyphae ends, suggesting that these appressoria were non-functional for causing infection. Furthermore, the mutant colonies lost hydrophobicity and had significantly reduced expression of the hydrophobin MPG1. However, overexpression of MPG1 in the mutants restored their hydrophobicity, but not pathogenicity. Stress assay showed that the mutants were more sensitive to SDS, CR and H2O2, but more tolerant to NaCl and SOR. In summary, our study revealed the essential role of the MoMyb13 in the growth, conidiation, hydrophobicity, stress response and pathogenicity of M. oryzae, and provides valuable insights into the working mechanism of Myb TFs in fungi.

Surface-enhanced Raman spectroscopy (SERS) can boost the pristine Raman signal by ~ 108 times that could be exploited for producing innovative sensing devices with advanced properties. However, the inherent complexity of SERS systems restricts their further applications in rapid detection, especially in situ detection in narrow aera. Here, we construct an efficient and flexible SERS-based LOP sensor by integrating Ag/Au nanocap arrays obtained by Ag/Au coating polystyrene nanospheres on the optical fiber face. We obtain rich “hotspots” at the nanogaps between neighboring nanocaps and further achieve the excellent SERS performance with the assistance of laser induced thermophoresis on the metal film that can achieve high efficiency aggregation of detected molecules. We achieve a high Raman enhancement with a low detection limitation of 10-7 mol/L for the most efficient samples based on the above sensor. This sensor also exhibits good repeatability and stability under multiple detections, revealing the potential application in situ detection based on the reflexivity of optical fiber.

Objective: Rett syndrome (RTT) is an X-linked neurodevelopmental disorder caused by mutations in MeCP2, a transcription factor. MeCP2 mutations cause abnormal expression of downstream genes and eventually lead to brain dysfunction. The role of MeCP2 in brain neural development remains unclear. To further elucidate this role, a MeCP2-null rat model was created with the CRISPR/cas9 system. Method: A MeCP2-cas9 vector was constructed and then microinjected into fertilized rat ova in vitro. Two mutations by CRISPR/cas9 were confirmed to cause deletions in exon 2 of MeCP2 via DNA sequencing, and protein expression was measured by Western blotting. Transcriptome data for three brain tissues, the cerebellum, cerebral cortex and hippocampus, were obtained via next-generation sequencing. Results: MeCP2-null rats were successfully obtained, and preliminary analysis showed that the MeCP2-null rats exhibited motor dysfunction and anxious and depressed behaviour. In addition, differentially expressed genes (DEGs) were identified in the three MeCP2-null brain tissues compared to wild-type rat brain tissues. In the rat cerebellum, 388 downregulated DEGs were mainly involved in the calcium ion signalling pathway and the PI3K-Akt signalling pathway. In the cerebral cortex, 386 upregulated DEGs were primarily involved in intracellular signal transduction, protein phosphorylation and the MAPK signalling pathway. In the hippocampus, the DEGs were related to the MAPK signalling pathway. Conclusion: We constructed a MeCP2-null rat model with unique features with CRISPR/cas9 technology to study RTT and analysed DEGs in three rat brain tissues to highlight potential targets for the development of new medicines.

Fire is a serious security threat that can lead to casualties, property damage, and environmental damage. However, despite the availability of object detection algorithms, challenges persist in detecting fires and smoke. These challenges include slow convergence speed, poor performance in detecting small targets, and high computational cost limiting deployments. In this paper, Fire smoke and human detection based on ConvNeXt and Mixed encoder (FCM-DETR), an end-to-end object detection algorithm based on Deformable DETR, is proposed. Firstly, we introduce ConvNeXt to take the place of Resnet, which greatly reduces the amount of computation and improves the ability to extract irregular flame features. Secondly, to effectively process multi-scale features, the original encoder is decoupled into two modules. Then Mixed encoder, an innovative encoder structure, is proposed, resulting in excellent performance of multi-scale fire and smoke features fusion. What can’t be overlooked is that the encoder block is compatible with any DETR-based models. Finally, the convergence speed is accelerated and the mean of average precision is improved by applying a novel loss function called Powerful IoU v2. The experimental results indicate that our model achieves the best detection accuracy compared to other models, with mAP reaching 66.7%, mAPs and Accuracyfire achieving impressive 50.2% and 98.05%, respectively.

The data assimilation method to improve sea fog forecast over the Yellow Sea is usually three-dimensional variational assimilation (3DVAR), whereas ensemble Kalman filter (EnKF) has not yet been applied on this weather phenomenon. In this paper, two sea fog cases over the Yellow sea, one spread widely and the other spread narrowly along the coastal area, are studied in detail by a series of numerical experiments with 3DVAR and EnKF based on the Grid-point Statistical Interpolation (GSI) system and the Weather Research and Forecasting (WRF) model. The results show that the assimilation effect of EnKF outperforms that of 3DVAR: for the widespread-fog case, the probability of detection and equitable threat scores of the forecasted sea fog area get improved respectively by ~57.9% and ~55.5%; the sea fog of the other case completely mis-forecasted by 3DVAR is produced successfully by EnKF. These improvements of EnKF relative to 3DVAR are benefited from its flow-dependent background error, resulting in more realistic depiction of sea surface wind for the widespread-fog case and better moisture distribution for the other case in the initial conditions. More importantly, the correlation between temperature and humidity in the background error of EnKF plays a vital role in the response of moisture to the assimilation of temperature, which leads to a great improvement on the initial moisture conditions for sea fog forecast.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

This study aimed to use spatiotemporal tensor data to measure the level of employment quality in China's provinces and analyzed the magnitude and direction of its influencing factors in the spatiotemporal dimension. Taked 30 provinces, autonomous regions and municipalities directly under the central government in China from 2011 to 2020 as the research object, the employment quality evaluation system was constructed from six dimensions of employment environment, employment status, employability, labor remuneration, social security, and labor relations. The employment quality index data was expressed as a three-order high-dimensional tensor spatio-temporal data form, and the employment quality of China's provinces was measured from the spatio-temporal perspective by using principal tensor analysis, and the visual analysis of the development and change process of employment quality was carried out. The spatial autocorrelation analysis of employment quality was carried out, and the time-space dual fixed effect model of the spatial Dubin model was selected to analyze the direction and magnitude of the influence factors of employment quality on itself and its neighboring provinces. The research showed that: (1) The overall level of employment quality in China was not high and the employment quality varies greatly among provinces, and the employment quality development gap among provinces showed a trend of widening. (2) The development of employment quality in western China was relatively fast, while the development of employment quality in central China showed insufficient stamina. (3) Sichuan Province had a strong radiation effect on the development of employment quality in neighboring provinces, and Beijing and Tianjin had a strong siphon effect on the development of employment quality in neighboring provinces. (4) The level of industrialization and informatization promoted the development of employment quality in China's provinces, while the industrial structure had a significant negative effect on the development of employment quality.

In response to the fairness issue arising from the unequal delay of vehicles in different phases at intersections, considering the actual situation of small and variable delays for vehicles in low-saturation intersection phases, this paper proposes the concept of "sacrificing efficiency for fairness." Firstly, the universality of unfair delay phenomena at intersection phases is explained, especially at low-saturation intersections where the fluctuation in phase delays is 1.87 times higher than at other intersections. Then, a fairness evaluation index is constructed using information entropy, and the feasibility of the proposed approach is demonstrated. Subsequently, a signal optimization model that balances efficiency and fairness is proposed. Finally, the proposed model is validated through case studies, showing that it not only simultaneously considers efficiency and fairness but also has minimal impact on efficiency. Moreover, the changes to timing schemes in the efficiency model are much smaller compared to the model that only considers fairness. Sensitivity analysis reveals that the model performs better under low-saturation intersection conditions.

The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Poverty alleviation is a hallmark of post-revolution Chinese policymaking. Since 1978, the Communist Party of China (CPC) has implemented successive waves of poverty alleviation policies whose effects have become the focus of an ever-increasing body of academic literature. This paper reviews this diverse but limited literature that evaluates the impact of the CPC’s poverty reduction programs through four major channels, namely fiscal investment programs, social safety nets, rural governance on the village-, county- and provincial level, and the relocation of rural populations from destitute regions. This paper aims to synthesize results and evaluate whether and how the abovementioned poverty alleviation programs have had distinct positive or negative impacts on regional development outcomes. Furthermore, I highlight contradictions in empirical findings to motivate the discussion about contextual importance when designing and implementing future poverty alleviation programs. Finally, I suggest that an exhaustive and critical appraisal of the empirical strategies used in this literature would further the development and application of more accurate and informative methodologies.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

The mammalian or mechanistic target of rapamycin (mTOR) integrates multiple intracellular and extra-cellular upstream signals involved in the regulation of anabolic and catabolic processes in cells, and plays a key regulatory role in cell growth and metabolism. Activation of the mTOR signaling pathway has been reported to be associated with a wide range of human diseases. A growing number of in vivo and in vitro studies have demonstrated that the gut microbes and its complex metabolites can regulate host metabolic and immune responses through the mTOR pathway, and result in disorders of host phys-iological functions. In this review, we summarize the regulatory mechanisms of gut microbes and mTOR in different diseases, and discuss the crosstalk between gut microbes and their metabolites and mTOR in the disorders in gastrointestinal tract, liver, heart and other organs. We also discuss the promising appli-cation of multiple potential drugs that can adjust the gut microbiota and mTOR signal pathways. Despite the limited findings between gut microbes and mTOR, elucidating their relationship may provide new clues for the prevention and treatment of various diseases.

As Artificial Intelligence (AI) technology, particularly Machine Learning algorithms, becomes increasingly ubiquitous, our abilities to understand and interpret AI and machine learning algorithms are becoming increasingly desirable. Visualization has been used as a common tool to view and understand complex machine learning processes. In this paper, we will focus on developing a general framework for the visualization of machine learning models as a scalar valued multi-dimensional function to help users understand how the models behave over different viewing spaces. We first give a formal definition of the visualization problem. Interpolation-based morphing and subspace sampling techniques are applied to generate various renderings through projections and cross-sections of the model space as 3D surfaces or heatmap images. This method will be applied to two real-world datasets and applications: the diagnosis of Alzheimer's Disease (AD) using a human brain networks dataset and a real-world benchmark dataset for predicting home credit default risks. The visualizations show that different machine learning algorithms can behave quite differently under different conditions.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

The diffusion coefficient (D) is a key parameter characterizing gas transport in coal seams. Usually, the D is calculated from the desorption curve of particle coal, which cannot accurately reflect the diffusion characteristics under the stress constraint conditions of in-situ coal seams. In this paper, based on Fick's law of counter diffusion, different metamorphic deformed coals of medium and high coal rank are taken as the research object. The change laws of D under different confining pressure, gas pressure, and temperature conditions are tested and analyzed, and the influencing mechanisms on the D are discussed. The results show that the D of different metamorphic deformed coals decreases exponentially with the increase of confining pressure, and increases exponentially with the increase of gas pressure and temperature. There is a limit diffusion coefficient. The influence of confining pressure on the D is essentially determined by the change of effective stress, and the D has a negative effect of effective stress similar to permeability. The effect of gas pressure on the D involves two mechanisms, namely, mechanical and adsorption effects, which are jointly restricted by effective stress and coal particle shrinkage and expansion deformation. The effect of temperature on the D is mainly achieved by changing the root mean square speed and average free path of gas molecules. Under the same temperature and pressure conditions, the D increases first and then decreases with the increase of deformation degree, and the D of fragmented coal is the largest. Under similar deformation conditions, the D of high-rank anthracite is greater than that of medium-rank fat coal. It is considered that porosity is the key factor affecting the change of D in different metamorphic deformed coals.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

Developing and utilising of underground space is an vital direction for urban growth. Underground commercial streets, as a significant component of underground space accommodating extensive human social activities, and consequently necessitate the creation of human-scale spaces. In the evolution of urban design development towards greater refinement, applying architectural theories and excessively subjective designs has resulted in a deficiency of human-centered design and a disordered spatial environment. This study merges environmental psychology and architectural theory to determine the appropriate length of spatial scale. Two experiments focusing on spatial perception evaluation were conducted using a virtual experimental platform that featured varying dimensions of spatial scale combinations. These quantified combinations were correlated with perception evaluation, and regression analysis was employed to identify appropriate scale ranges, which were superimposed on the range of length selection. Finally, the optimal length and scale combination for underground commercial street spaces were established, providing a reference for the human-centered design of these environments.

There are four subtypes of adenosine receptors (ARs), named A1, A2A, A2B and A3, all of which are G protein-coupled receptors. The A2BAR, coupled to both Gαi and Gαq G proteins, is one of the several G-protein-coupled receptors that are expressed in a significantly higher level in some cancer tissues in comparison to adjacent normal tissues. There is growing evidence that the A2BAR plays an important role in tumor cell proliferation, angiogenesis, metastasis, and immune suppression. Thus, A2BAR antagonists are potentially novel attractive anticancer agents. Several antagonists targeting at the A2BAR are currently in clinical trials for various types of cancers. In this review, we first describe the signaling, agonists, and antagonists of the A2BAR. We further discuss the role of the A2BAR in the progression of various types cancers, and the rationale of using A2BAR antagonists in cancer therapy

p53 is among the most frequently mutated tumor suppressor genes given its prevalence in >50% of all human cancers, including high grade serous endometrial cancers and ovarian cancers. In addition to loss of tumor suppression function, many mutated p53 (Mutp53) proteins acquire gain-of-function (GOF) activities as oncogenes to promote cancer progression, which manifest through aberrant expression of p53. As we have come to see, statins induce CHIP-mediated degradation of mutp53 by blocking the interaction between mutp53 and DNAJA1. Therefore, targeting critical downstream pathways of mutp53 provides an alternative strategy for treating cancers expressing mutp53. In this review, we summarize recent advances with Wee1 inhibitors and mevalonate pathway inhibitors, particularly statins, regarding their use in gynecological cancers with p53 mutations.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Iron tailings are solid waste generated after the mining of iron mines, which have caused serious damage to the surrounding ecology and environment and have attracted widespread attention. By analyzing the formation causes, main components, and environmental effect mechanisms of iron tailings, the article systematically elaborates on the degree and mechanism of the harm of iron tailings to water bodies, atmosphere, soil, and ecosystems, and evaluates its impact on human health and sustainable development of society. On this basis, specific prevention and control measures have been proposed to reduce iron tailings emissions, realize resource recycling, and restore ecosystems. Research shows that iron tailings containing heavy metals can widely pollute the environment through dissolution and migration, and have significant biological toxicity effects. The research results can provide a theoretical reference for decision-making departments to formulate scientific and reasonable iron tailings disposal and ecological protection policies. It is recommended to strengthen specific research on the infiltration of toxic and harmful components in tailings in the future, and develop efficient and stable solidification technology, and vegetation-microbial joint restoration models to further reduce the ecological and environmental risks of iron tailings.

Proper Post-Activation Performance Enhancement helps to improve athletic performance. This study aimed to investigate the effects of two different velocity loss (VL), 10%VL and 20%VL, on post-activation performance enhancement (PAPE) in 20m sprint performance among sprint athletes. Twenty-four male sprint athletes (100m sprint time: 10.96±0.15 s) were recruited. A randomized crossover experimental design was used for traditional group (TG), 10%VL, and 20%VL interventions. Sprint tests were conducted at the 4th, 8th, 12th, and 16th minutes after the intervention. Two-way repeated measures ANOVA revealed an interaction effect between group and time on 20m sprint performance (F=2.817, p=0.037, partial η²=0.585). Simple effect analyses showed significant differences compared to baseline at the 4th minute for the 20%VL group (P<0.05). Cohen's d values indicated improvement in 10m sprint times at the 8th minute of the rest interval for all three intervention groups (TG: ES=-0.270, 10%VL: ES=-0.038, 20%VL: ES=-0.279). Improvement in 20m sprint times was observed at the 4th minute for the 20%VL group (ES=-0.296) and at the 16th minute for the 10%VL group (ES=-0.276). Compared to traditional PAPE schemes based on 1RM, PAPE schemes based on velocity loss (20%VL) can better induce PAPE effects in sprint athletes.

Information encryption and anti-counterfeiting play an important role in many aspects of daily life, such as in minimizing economic losses, protecting secure communication and public security, and so on. Owing to the high information capacity and ease of operation, luminescent materials for advanced information encryption and anti-counterfeiting are essential to meet the increasing demand on encryption security. Herein, we summarize two emerging luminescent materials for information encryption and anti-counterfeiting, the AIE materials and room-temperature phosphorescent materials. At last, we discuss the opportunities and anticipations of these two information encryption and anti-counterfeiting materials.

Transposons are mobile DNA sequences that contribute large fractions of many plant genomes. They provide exclusive resources for tracking gene and genome evolution and for developing molecular tools for basic and applied research. Despite extensive efforts, it is still challenging to accurately annotate transposons, especially for the beginners as transposon prediction requires necessary expertise in both transposon biology and bioinformatics. Moreover, the complexity of plant genomes and the dynamic evolution of transposons also bring difficulties for genome-wide transposon discovery. This review summarizes the three major strategies for transposon detections including repeat-based, structure-based, and homology-based annotation, and introduces the transposon superfamilies identified in plants thus far, and some related bioinformatics resources for detecting plant transposons. Furthermore, it describes the transposon classification and explains why the terms of ‘autonomous’ and ‘non-autonomous’ cannot be used to classify the superfamilies of transposons. Last, this review also discusses how to identify misannotated transposons and improve the quality of transposon database. This review provides helpful information about plant transposons and a beginner’s guide on annotating these repetitive sequences.

The International Roughness Index (IRI) is the standard scale for evaluating road roughness in many countries in the world. The Taipei City government actively promotes a Road Smoothing Project and plans to complete the rehabilitation of the main and minor roads within its jurisdiction. This study aims to detect the road surface roughness in Taipei City and recommend appropriate IRI thresholds for road rehabilitation. A total of 171 asphalt concrete pavement sections in Taipei City with a total length of 803.49 km were analyzed and compared by IRI. The longitudinal profile of the detected road sections was measured using an inertial profiler. The statistical analysis showed that the IRI value prior to road leveling was mainly distributed between 5 and 8 m/km, while the IRI value after road leveling was mainly distributed between 3 and 4.5 m/km. This confirms that the implementation of the Road Smoothing Project has a significant effect on improving road smoothness. Moreover, based on the analysis results, it is recommended that the IRI threshold value for road rehabilitation in Taipei City be set at 4.50 m/km.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

Weather radar plays a crucial role in the monitoring of severe convective weather. However, due to its limited detection range, it cannot conduct effective monitoring in remote offshore areas. Therefore, this paper utilized the Unet++ to establish a model for retrieving radar composite reflectivity based on Himawari-9 satellite datasets. In the process of comparative analysis, we found that both satellite and radar data exhibit significant diurnal cycles, but there are notable differences in their variation characteristics. To address this, we established 4 comparative models to test the influence of latitude and diurnal cycles on the inversion results. The results show that adding the distribution map of the minimum cloud-top brightness temperature at the corresponding time in the model can effectively reduce the root mean square error (RMSE) of the model and enhance the accuracy of severe convective weather monitoring. This conclusion can be applied in the future to enhance and improve satellite quantitative precipitation estimation.

The evaporation of polymer solution droplet is an important in solution-based polymer film fabrications, such as inkjet print, spray coatings, and droplet casting etc. In this work, we investigated the effect of droplet size, solvent evaporation rate, and concentration on “coffee-ring” effect, crystal nucleation, polymorphism, and morphology of dried poly (vinylidene fluoride) (PVDF) solution droplets with atomic force microscopy (AFM) method. We found that the crystal structure, morphology and crystal distribution in the center and edge regions of dried PVDF droplets were different due to “coffee-ring” effect. The “coffee-ring” effect of dried PVDF droplets was mainly composited of accumulated crystals at the edge region of droplet, which was mainly made by crystallization of migrated chains. The interplay between migration of chains, crystallization and solidification of PVDF droplets significantly influenced the formation of “coffee-ring”. In addition, our results showed that the decrease of droplet size and controlling solvent evaporation rate were effective ways to improve the PVDF β-phase nucleation and decrease crystal size.

Nuclear magnetic resonance (NMR) techniques are widely used to identify pure substances and probe protein dynamics. Edible oil is a complex mixture composed of hydrocarbons, which have a wide range of molecular size distribution. In this research, low field NMR (LF-NMR) relaxation characteristic data of various sample oils were analyzed. We also suggest a new method for prediction size of edible oil molecules using LF-NMR relaxation time distributions. According to the relative molecular mass, carbon chain length, transverse relaxation time of different sample oils, combined with oil viscosity and other factors, the relationship between carbon chain length and transverse relaxation time rate was analyzed. Various oils and fats in the mixed fluid are displayed, reflecting the composition information of different oils. To study the correlation between the rotation correlation time and molecular information of oil molecules. The molecular composition of the resulting fluid determines its properties, such as viscosity and phase behavior. The results show that low-field NMR can obtain information on the composition, macromolecular aggregation, and molecular dynamics of complex fluids. Measurements of grease in the free fluid state show that the relaxation time can reflect the intrinsic properties of the fluid. It is shown that the composition characteristics and states of complex fluids can be measured by low-field nuclear magnetic resonance.

Based on screening in computational biology and biological in vitro assays, five natural products isolated from extracts of the herbal medicine toad skin, such as cinobufagin (CBFi), bufalin (BFi), arenobufagin (ABFi), telocinobufagin (TBFi), bufotalin (BFTi), were subjected to molecular docking calculations with the use of SARS-CoV-2 main protease (PDB 6LU7 and 7BTF) and top-scoring ligand-receptor complexes were obtained. The results showed that the binding energy of ABFi to the 3CL protein was -17.044kcal/mol, which was higher than CBFi and TBFi. However, the binding energy of ABFi to the RdRp protease was -23.250 kcal/mol, which was much lower than that of CBFi and TBFi, EVEN lower than that of ABFi to the 3CL protein. ABFi also has polar interactions with amino acids such as Glu811, Ser814, Ser681 and Thr680 of RdRp enzyme. The results revealed that ABFi had a moderate inhibitory effect on the cell proliferation of SARS-CoV-2 in vitro, with an inhibition rate of 61.12%, even weaker than Remdesivir. This new discovery provides us with new ideas for in-depth studies on the development of natural products with this class of structural generalizations as inhibitors of SARS-CoV-2, and provides an experimental basis for the next step of mechanistic studies.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

Starfish are keystone species as predators in benthic ecosystems, but when population outbreaks occur this can have devastating consequences ecologically. Furthermore, starfish outbreaks and invasions can have adverse impact economically by impacting shellfish aquaculture. Addressing the imperative need to proactively mitigate starfish invasions requires comprehensive research on their behavior and the underlying mechanisms of outbreaks. This review scrutinizes the historical patterns of outbreaks among diverse starfish species across various regions, delineates the factors contributing to the proliferation of Asterias amurensis in Chinese waters, articulates preventive and remedial strategies, and outlines the potential for sustainable utilization of starfish.

When liquids are confined into nanometer-scale slit, the induced layering-like film structure allows the liquid to sustain non-isotropic stresses and thus being load-bearing. Such anisotropic characteristics of liquid under confinement arise naturally from the liquids’ wave number dependent compressibility that does not need solidification to take place as a prerequisite. In other words, liquids under confinement can still remain fluidity with molecules being (sub-)diffusive. However, the extensively prolonged structural relaxation time can cause hysteresis of stress relaxation of confined molecules in response to the motions of confining walls and thereby yield the quasi-static stress tensor history-dependent. In this work, by means of molecule dynamics, the discrepancy of stress tensor of a highly confined key base-oil component, i.e. 1-decene trimer, is captured after its relaxation from being compressed and decompressed. The results indicate that among the effects (e.g. confinement, molecular structure, and film density) that can potentially affect confined stress tensor, the ordering status of the confined molecules plays a predominant role.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

Multi-view stereo (MVS) employs multi-point photography for image point positioning and three-dimensional reconstruction technology. Recently, this technology has been introduced into the monitoring of road slopes due to advances in photography and computing technology. In general, the various phases of post-image processing procedures are applied to various photographic data. In this study a novel, automated image-monitoring system is proposed to improve the ability of automatic processing. First, an Internet of things (IoT)-based digital photography system architecture was constructed to provide automatic control of camera photography and real-time transmission of image data. In addition, a visual SfM-MVS 3D reconstruction technique was used to develop related software and hardware interfaces based on the built-in Python computing framework of Photoscan Pro. The software integrates fully automatic photography, image transmission, monitoring of data processing and product release programs. The experimental results show that the system architecture can be applied to fully automatic three-dimensional monitoring of road slopes.

This paper proposes a position recognition method for the receiver coil by the secondary coil current. Based on the practical value of the current of the receiver coil, the position recognition of the receiver coil in the WPT system is realized. This paper proposes a 3×3 array multi-transmitter coil grouping and control logic. The mathematical model of mutual inductance between the receiver and transmitter coil at different positions on the X-Y plane is established. A method for identifying the position of the receiver coil according to the current of the receiver coil is proposed. Compared with the traditional position recognition method of the receiver coil, this method does not need to add a detection coil and position sensor and can realize the position recognition of the receiver coil on the 2D plane.

Drugs-drugs interactions(DDI) are entities composed of different chemical substructures (functional groups). In existing methods that predict drug–drug interactions based on the usage of substructures, each node is considered the center of a substructure, and adjacent nodes eventually become centers of similar substructures, resulting in redundancy. Furthermore, the significant differ- ences in structure and properties among compounds can lead to unrelated pairings, making it difficult to integrate information. This heterogeneity negatively affects the prediction results. To address these issues, we propose a drug–drug interaction prediction method based on substructure signature learning (DDI-SSL). This method extracts useful information from local subgraphs surrounding drugs and effectively utilizes substructures to assist in predicting drug side effects. Additionally, a deep clustering algorithm is used to aggregate similar substructures, allowing any individual subgraph to be reconstructed using this set of global signatures. Furthermore, we developed a layer-independent collaborative attention mechanism to model the mutual influence between drugs, generating signal strength scores for each class of drugs to mitigate noise caused by heterogeneity. Finally, we evaluated DDI-SSL on a comprehensive dataset and demonstrated improved performance in DDI prediction compared to state-of-the-art methods.

The practice of quantified-self sleep tracking is increasingly common nowadays among healthy individuals as well as patients with sleep problems. However, existing sleep-tracking technologies only support simple data collection and visualization, and are incapable of providing actionable recommendations that are tailored to users' physical, behavioral and environmental context. Here we coined the term context-aware sleep health recommender system (CASHRS) as an emerging multidisciplinary research field that bridges ubiquitous sleep computing and context-aware recommender systems. In this paper, we presented a narrative review to analyze the type of contextual information, the recommendation algorithms, the context filtering techniques, the behavior change techniques, the system evaluation, and the challenges in peer-reviewed publications that meet the characteristics of CASHRS. Analysis results identified current research trends, the knowledge gap, and future research opportunities in CASHRS.

Phase synchronization is one of the key issues that must be addressed in the bistatic synthetic aperture radar (BiSAR) system. LuTan-1 is an innovative L-band spaceborne BiSAR mission of China. An advanced synchronization scheme is used in the LuTan-1 system. The synchronization pulses are exchanged immediately after the ending time of the radar echo receiving window and before the starting time of the next pulse repetition interval. Therefore, it can not interrupt the normal SAR data acquisition, further improving synchronization frequency and avoiding the data missing effect. In order to accurately monitor system malfunctions and compensate for the phase synchronization errors introduced by hardware system, an innovative internal calibration strategy is designed and employed in the LuTan-1 mission. The test data acquired from the ground validation system of LuTan-1 are used to demonstrate the feasibility of the proposed scheme. The results validate the effectiveness of the proposed scheme and prove the promise for its future application in LuTan-1.

Often, engineers with machining experience often judge machining state and tool life according to chips’ features. Engineers' experience is digitized in this study. During the cutting process, the cutting tool coming in contact with the workpiece produces a shear zone, which causes plastic deformation and shear slip. The chips closest to the shear zone can directly show the state of the tool and workpiece when the material is SKD61. This study used chip color, vibration, and current signal integration for prediction of machining state and cutting tool life. When the cutting tool wears increased, the chip surface color changed in the following way: purpleè purple blueè blue ècyan, or even green and yellow. When the cutting tool was in the accelerating wear phase, the color change was particularly obvious. The Back-Propagation Levenberg–Marquardt (BP-LM) predictive methodology was used to compare the predictive ability of voltage, vibration signal, and chip color. The Mean Absolute Percentage Error (MAPE) for the voltage signal was 12.28%, for the vibration signal it was 11.38%, and for the chip color combined with multi-sensor characteristics it was 7.85%. The MAPE of the chip color was the smallest. Using the General Regression Neural Network (GRNN) methodology, the MAPE for the voltage signal was 10.74%, for the vibration signal 7.96%, and for the chip color combined with multi-sensor characteristics was 6.59%. The MAPE of the chip color was the smallest. Obviously, the chip color combined with multi-sensor signals provided better predictive results than the vibration signal or voltage signal alone. There is currently no research on the usefulness of monitoring chip color for tool life prediction.

A large amount of concrete waste is generated around the world and its recycling is an urgent issue. In this research, a new approach to recycle concrete waste with wooden waste was studied. Concrete and wooden wastes were crushed, mixed, and heat compacted to produce plates with different water contents and mix proportions at various temperatures, pressures, and durations of compaction. The bending strength of the plates was measured after compaction. The result indicated that with an increase in the percentage of wooden waste in the mixture, pressure, or temperature improved the bending strength. The increase in water content reduced the bending strength. Most of the products exhibited higher bending strength than that of ordinary concrete.

The effective integration of aerial remote sensing data and ground multi-source data has always been one of the difficulties of quantitative remote sensing. A new monitoring mode is designed which installs the hyperspectral imager on the UAV and places a buoy spectrometer on the river. Water samples are collected simultaneously to obtain in situ assay data of total phosphorus, total nitrogen, COD, turbidity and chlorophyll during data collection. The cross correlogram spectral matching (CCSM) algorithm is used to match the data of the buoy spectrometer with the UAV spectral data to reduce the UAV data noise significantly. An absorption characteristics recognition algorithm (ACR) is designed to realize a new method for comparing UAV data with laboratory data. This method takes into account the spectral characteristics and the correlation characteristics of test data synchronously. It is concluded that the most accurate water quality parameters can be calculated by using the regression method under five scales after the regression tests of multiple linear regression method (MLR), support vector machine method (SVM) and neural network (NN) method. This new working mode of integrating spectral imager data with point spectrometer data will become a trend in water quality monitoring.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

To solve the benefit allocation problem between the subjects of the supply chain of general contracting projects. The Cobb-Douglas function is applied to establish the benefit distribution model when the two cooperate in the supply chain system, analyze the optimal benefit situation of one-time cooperation between the two parties under two modes of egoistic decision and collectivistic decision as well as the benefit distribution problem of multiple cooperation, and conduct numerical simulation to calculate the functional relationship between each decision variable and the contribution degree of the general contractor under different effort cost coefficients. The results show that：In the case of one-time cooperation between general contractors and subcontractors, regardless of the decision mode, the degree of effort of both parties is positively related to their own contributions and negatively related to each other's contributions; the overall benefit of the supply chain system is positively proportional to the degree of contribution of the general contractor and inversely proportional to the share of benefit distribution of the subcontractor; in multiple cooperation, the equilibrium result of both parties achieving Pareto optimality at each stage is that both parties choose to cooperate.

The chitin synthase B gene is a key enzyme in the chitin synthesis of insect peritrophic matrix (PM), affecting insects' feeding behavior. The chitin synthase B gene has been cloned from the transcription library of Heortia vitessoides Moore. RT-qPCR showed that HvChsb was highly expressed in the larval stage of H. vitessoides, especially on the first day of the prepupal stage, and in the midgut of larvae and the abdomen of adults. After starvation treatment, HvChsb was found to be significantly inhibited with time. After 48 h of starvation, the feeding experiment showed that HvChsb increased with the prolongation of the refeeding time. The experimental data showed that feeding affected the expression of HvChsb. HvChsb was effectively silenced by RNA interference, so its function was lost, significantly decreasing the survival rate of H. vitessoides. The survival rate from larval-to-pupal stages was only 43.33%, accompanied by abnormal phenotypes. It can be seen that HvChsb plays a key role in the average growth and development of H. vitessoides.

Panax notoginseng is a traditional Chinese medicine, and saponins are its main active ingredients. The content of saponins in flower of P. notoginseng is the highest in the whole plant. Minor ginsenosides have stronger pharmacological activity than main ginsenosides, but its content in nature is very low. We can use extracted total saponins from P. notoginseng flower as the substrate to produce minor ginsenosides by biotransformation method. In this study, we used the fungus Talaromyces flavus and its crude enzymes to transform the extracted total saponins of P. notoginseng flower. Through the qualitative and quantitative analysis of the transformation substrates and products, it was found that minor ginsenosides Gyp-XVII, ginsenosides C-Mc1, C-Mx1, F2, Rg3, 20(R)-Rg3, Rk1 and Rg5 were found in the products and the conversion rate of the major saponins in P. notoginseng flower ranged from 44.16 to 55.22%, the yields of the minor ginsenosides ranged from 0.05 to 3.24%. This study provided a good experimental idea, greatly increased the utilization rate of total saponins in P. notoginseng flower, and laid a foundation for promoting the wide application of minor saponins.

This paper presents a deep learning-based multi-guidance line detection approach, enabling an autonomous four-wheeled agricultural robot to navigate strip farmland. The integration of Proportional-Integral-Derivative (PID) and Fuzzy Logic Control (FLC) systems optimizes the velocity and heading angle of robot, facilitating smooth navigation along identified guidance line. Enhance cornering maneuverability with real-time kinematics (RTK)-assisted Global Navigation Satellite System (GNSS) (RTK-GNSS) positioning. Additionally, the spraying system combined with deep learning can effectively identify weeds and crop nutrient deficiencies to achieve precise spraying. The guidance system prioritizes irrigation lines for navigation, with additional guidance from crop and furrow lines. Trigonometric analysis determines the angular deviation between the identified guidance line and the vertical line of the top view image. Experiments under diverse weather conditions demonstrate the stable navigation of robot at 12.5 cm/s, achieving up to 90% accuracy in weed and nutrient deficiency identification. The spraying accuracy for weeds and deficiencies averages 87% and 73%, respectively, underscoring the system's contribution to sustainable and precision horticulture practices.

This is the first study to provide a systematic monetary benefit matrix, including greenhouse gas (GHG) emissions reduction benefits and air pollution reduction health co-benefits, for a change in on-the-road transport to low-carbon types. The benefit transfer method is employed to estimate the social cost of carbon and the health co-benefits via impact pathway analysis in Taiwan. Specifically, the total emissions reduction benefits from changing all internal combustion vehicles to either hybrid electric vehicles, plug-in hybrid electric vehicles, or electric vehicles would generate an average of US$760 million from GHG emissions reduction and US$2,091 million from health co-benefits based on air pollution reduction, for a total benefit of US$2,851 million annually. For a change from combustion scooters to light- or heavy-duty electric scooters, the average GHG emissions reduction benefits would be US$96.02 million, and the health co-benefits from air pollution reduction would be US$1,008.83 million, for total benefits of US$1,104.85 million annually.

Change orders have received considerable attention from researchers thus far, but none have considered pricing strategies of change orders through the interaction between general contractors and subcontractors. Previous studies found that contractors’ opportunistic bidding considering beyond-contractual reward (BCR) in the execution stage can be reduced by improving the construction management system and strengthening the supervision of contractors’ performance. However, the BCR remains in ecology of construction engineering. This study proposes an integrated evolutionary game theory-system dynamics model (ET-SD model) and simulates the pricing strategy of change orders between general contractors and subcontractors to explore the root cause of BCR phenomenon. Sensitivity analysis on the evolutionary dynamics of payoff is explored. Results reveal that change orders with BCR maintain Nash equilibrium and evolutionary stable strategy (ESS) unless changing the payoff structure between general and subcontractors’ pricing strategies. This study presents important managerial insights from the evolutionary game perspectives, nature of change orders, and payoff of the alternative.

Despite the partial disclosure of driving scenario knowledge graphs, they still fail to meet the comprehensive needs of intelligent connected vehicles for driving knowledge. Current issues include the high complexity of pattern layer construction, insufficient accuracy of information extraction and fusion, and limited performance of knowledge reasoning models. To address these challenges, a hybrid knowledge graph method was adopted in the construction of the Driving Scenario Knowledge Graph (DSKG). Firstly, core concepts in the field were systematically sorted and classified, laying the foundation for the construction of a multi-level classified knowledge graph top-level ontology. Subsequently, by deeply exploring and analyzing the Traffic Genome data, 34 entities and 51 relations were extracted and integrated with the ontology layer, achieving the expansion and updating of the knowledge graph. Then, in terms of knowledge reasoning models, an analysis of the training results of the TransE, Complex, Distmult, and Rotate models in the entity linking prediction task of DSKG revealed that the Distmult model performed the best in metrics such as hit rate, making it more suitable for inference in DSKG. Finally, a standardized and widely applicable Driving Scenario Knowledge Graph was proposed. The DSKG and related materials have been publicly released for use by industry and academia.

DNA methylation, one of the major epigenetic mechanisms, plays critical roles in regulating gene expression, genomic stability and cell lineage commitment. Establishment and maintenance of DNA methylation in mammals is achieved by two groups of DNA methyltransferases: DNMT3A and DNMT3B, which are responsible for installing DNA methylation patterns during gametogenesis and early embryogenesis, and DNMT1, which is essential for propagating DNA methylation patterns during replication. Both groups of DNMTs are multi-modular proteins, containing a large N-terminal regulatory region in addition to the C-terminal methyltransferase domain. Recent structure-function investigations of the individual domains or large fragments of DNMT1 and DNMT3A have revealed the molecular basis for their substrate recognition and specificity, intramolecular domain-domain interactions, as well as their crosstalk with other epigenetic mechanisms. These studies highlight a multifaceted regulation for both DNMT1 and DNMT3A/3B, which is essential for the precise establishment and maintenance of lineage-specific DNA methylation patterns in cells. This review summarizes current understanding of the structure and mechanism of DNMT1- and DNMT3A-mediated DNA methylation, with emphasis on the functional cooperation between the methyltransferase and regulatory domains.

In this paper, the catalytic combustion of DMDS (dimethyl disulfide, CH₃SSCH₃) over bimetallic supported catalysts were investigated. It was confirmed that Cu/γ-Al₂O₃-CeO₂ showed best catalytic performance among the five single-metal catalysts. Furthermore, six different metals were separately added into Cu/γ-Al₂O₃-CeO₂ to investigate the promoting effect. The experiments revealed Pt as the most effective promoter and the the best catalytic performance was achieved as the adding amount of 0.3 wt%. The characterization results indicated that high activity and resistance to sulfur poisoning of Cu-Pt/γ-Al₂O₃-CeO₂ could be attributed to the synergistic effect between Cu and Pt.

With increasing air and sea temperatures, the thermodynamic environments over the oceans become more favourable for the development of intense tropical cyclones (TCs) with rapid intensification (RI). In fact, the number of TCs undergoing RI is rising (Zhao, et al., 2018; Bhatia, et al., 2019; Song, et al., 2020; Hong & Wu, 2021; Liu, et al., 2022). RI over coastal sea areas before landfalling is particularly impactful and threatening to coastal lives and properties. There have been studies showing that offshore areas within 400 km of the coastline have experienced a significant increase in RI events with the count tripling from 1980 to 2020 (Li et al., 2023). The south China coastal region consists of highly densely populated cities especially the Pearl River Delta (PRD) region. Intense TCs maintaining its strength or RI of TCs close to the coastal region presents substantial forecasting challenges. This study investigates the effect of sea surface and subsurface temperature and salinity on the intensification of five TCs, namely Super Typhoons Hato in 2017 and Mangkhut in 2018, Typhoon Talim, Super Typhoon Saola and Severe Typhoon Koinu in 2023, which significantly affected the south China coastal region and triggered high TC warning signals in Hong Kong. The analysis utilized the Hong Kong Observatory (HKO) TC track and intensity data, along with the sea temperature and salinity profiles generated using the China Ocean ReAnalysis version 2 (CORA2) of the National Marine Data and Information Service (NMDIS) of China. While high sea surface temperature (SST) of 30°C or above, low surface sea surface salinity (SSS) of 34 psu or below, and strong salinity stratification of at least 0.8 psu per 100 m depth may offer useful hints for predicting RI, they are part of a broader set of contributing factors. This study represents the initial documentation of sub-surface salinity's impact on intense TCs over the South China Sea (SCS) in recent years and will encourage further research to refine forecasting RI of TCs before making landfall near PRD taking into account the effect of freshwater from the Pearl River.

Fluorescence microscopic images of cells contain a large number of morphological features that are used as an unbiased source of quantitative information about cell status, through which researchers can extract quantitative information about cells and study the biological phenomena of cells through statistical and analytical analysis. As an important research object of phenotypic analysis, images have a great influence on the research results. Saturation artifacts present in the image result in a loss of grayscale information that does not reveal the true value of fluorescence intensity. From the perspective of data post-processing, we propose a two-stage cell image recovery model based on generative adversarial network to solve the problem of phenotypic feature loss caused by saturation artifacts. The model is capable of restoring large areas of missing phenotypic features. In the experiment, we adopt the strategy of progressive restore to improve the robustness of the training effect, and add the contextual attention structure to enhance the stability of the restore effect. We hope to use deep learning methods to mitigate the effects of saturation artifacts to reveal how chemical, genetic, and environmental factors affect cell state, providing an effective tool for studying the field of biological variability and improving image quality in analysis.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

The processes of soliton generation and interference focus on the complex nonlinear soliton dynamics resembling matter particles. In order to further understand the dynamic process of solitons from a multidimensional perspective, here we report the vectorial solitons nature under two-sets pulse splitting in a single cavity induced by dual-core fiber assisted ultrafast fiber lasers. Owing to the weakly coupled cores in symmetrical dual core fiber (SDCF), two pulse groups interaction are formed in a cavity. By using the dispersive Fourier transformation technique (DFT), it was found that the four-component polarized rotation vector solitons (PRVS) generate. Moreover, gradually increasing the power can obtain the locked soliton bound state in two core space, and the corresponding evolution is similar to that of non-degenerate bright solitons in Bose Einstein condensates (BEC). In addition, by properly controlling the soliton phase offset in SDCF, the soliton rain state of multi pulse evolution can be obtained. The related experimental results would be fruitful to the communities interested in soliton dynamics and frequency comb lasers.

The construction time of concrete structures in hydraulic tunnels is long, the construction environment is complex, and there are many influencing factors. The requirements for construction quality are high, not only to meet the strength requirements, but also to meet the design requirements of erosion resistance, crack resistance, and seepage resistance according to its specific operating environment. Therefore, evaluating the construction quality of concrete structures in hydraulic tunnels is of great significance. Considering the randomness and fuzziness of factors affecting the construction quality of concrete structures in hydraulic tunnels, this paper proposes a comprehensive evaluation model based on Combined Weighting (CWM) and Uncertainty Measurement Theory (UM). The IAHP method and CRITIC method are used to determine the subjective and objective weights of evaluation indicators, combined weighting is based on the principle of minimum entropy, and the UM method is used to evaluate the construction quality level. Finally, taking a hydraulic tunnel as an example, its construction quality grade is calculated to be III according to the evaluation model proposed in this paper, which matches with the engineering reality, and a comparative study is made with the mixture element topology theory at the same time. It is verified that the evaluation model can scientifically and reasonably evaluate the construction quality level of concrete structures in hydraulic tunnels.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

In the mold machining process, the cutting tool is worn with machining time, thereby affecting the surface accuracy, leading to poor workpiece dimensions, even fracture. At present, many studies have used multiple sensors to detect the machining conditions of cutting tool and workpiece, including indirect measurement method and direct measurement method. The indirect measurement method, which has been studied widely, mainly uses sensors to capture signals for subsequent data analysis; the direct measurement method mainly analyzes the state of cutting shear zone. Due to the cut-in of cutting tool in the machining process, the workpiece is dislocated rapidly, generating considerable amount of heat, which is transferred to the chips, inducing color change on the surface of chips. Many engineers with machining experience often judge the machining state and tool life according to the chips. The engineers' experience is digitized in this study, and indirect measuring sensors are used to predict the tool life, so as to attain the objective for smart manufacturing, the average percentage error of MAPE using single vibration and voltage eigenvalues as input features is 10%, the voltage signal characteristic values and vibration signal characteristic values are combined. Finally, the chip surface chromaticity eigenvalue is combined with signal characteristic value. The average prediction error of BP-LM method is 7.85%, the average prediction error of GRNN method is 6.59%. Therefore, when the eigenvalue of chip surface chromaticity is added to the prediction result, it can enhance the accuracy of cutting tool wear value prediction more effectively than single sensor signal characteristic value.

Li₂MnO₃ is critical component in the well-studied Li-excess cathode materials xLi₂MnO₃•(1- x)LiMO₂ for achieving high lithium storage capacity. In this article, the diffusion of Li ions in Li₂MnO₃ is studied using molecular dynamics (MD) simulation with well-behaved empirical force fields obtained by fitting against the crystal structure from experiment and phonons calculated using Density Function Theory (DFT). We have found two possible tetrahedral hopping channels, 0-TM and 1-TM(Mn⁴⁺) channel, which are differentiated by the face sharing octahedral cations. Simulation results show that the 0-TM channel is active for Li hopping, while 1-TM(Mn4+) channel is inactive. During the delithiation process, the Li ions in the TM layered are firstly removed, then those in the Li layer. However, the Li ions will be trapped in the tetrahedral 0-TM channels as long as the four face sharing octahedral sites are cleared. Up to x=1.0 for Li₂-xMnO₃, almost all the Li ions are located at the tetrahedral sites, forming a regular array along a axis. The de-intercalation of tetrahedral Li ions requires a high voltage (>5.2 V vs. Li/Li+), limiting the practical capacities measured in lab. The diffusion of Mn ions into the Li layers is observed in a deeper delithiated structure (x=1.2 for Li₂-xMnO₃), indicating an initial phase transformation to a spinel-like structure. However, the Mn ions are mainly trapped in the tetrahedral sites in the Li layer, instead of the octahedral sites fin spinel-like structure. A few of Mn ions diffusing into the octahedral sites in Li layers have no face sharing tetrahedral Li ions, revealing a further Li de-intercalation is imperative for the complete phase transformation. Our model is not stable for x≥1.4 in Li₂-xMnO₃. Other charge compensation mechanism should be considered in this high delithiation stage, eg. oxygen release.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

Rollover prevention of partially-filled tank trucks is an industry teaser, with the core challenge being real-time perception and observation of the liquid state inside the tank. In order realize re-liable observation of sloshing liquid, this article firstly proposes a sloshing modeling method based on multi-degree-of-freedom pendulum model, and derives the double mass trammel pendulum model (DMTP, 2DOF) accordingly, which accurately reflects the sloshing dynamics under more pervasive working conditions. Secondly, a free surface fluctuation sensor is designed based on magnetostriction, capable of measuring the inclination and height of the liquid level inside tanks filled with hazardous chemical. Finally, the unscented Kalman filter (UKF) is utilized to synthesize the information of the two, establishing a credible real-time observation of the sloshing liquid. Verified through vehicle-fluid coupled co-simulation, under condition of con-secutive double lane change, observation error of the proposed method is only 25.9% that of the open-loop calculation, providing a secure guarantee for the observation of the state variables of the single pendulum model (SP) used for most kinds of anti-rollover controller.

The problem of identifying functional regions in an urban setting has been approached in literature using two general methodologies: top-down, encoding expert knowledge on urban planning and design (e.g. into patterns) and using that knowledge for identification, and bottom-up, relying on crowdsourcing and Volunteered Geographic Information (VGI) to train learning models, using techniques such as Latent Dirichlet Allocation (LDA) topic modeling. Both approaches have their advantages but also face important limitations, with knowledge-based approaches being criticized for scalability and transferability issues and data-driven approaches for lacking interpretability and depending heavily on data quality. To mitigate these disadvantages, we propose a novel framework that fuses data and knowledge in three different ways: functional regions identified from individual approaches are evaluated against each other, knowledge from patterns is used to adjust learning model results and topic models are used to adjust pattern-based results. The proposed methodologies are demonstrated through the use case of identifying shopping-related functional regions in the Los Angeles metropolitan area. Results show that the combination of results from knowledge-based and data-driven techniques can help uncover discrepancies between the two different approaches and smoothen inaccuracies caused by the limitations of each approach.

Zirconium dioxide (ZrO2) possesses numerous advantages such as high mechanical strength, low friction coefficient, excellent optical properties, and extended lifespan. Consequently, ZrO2 has a broad research foundation and practical significance in functional films and wear-resistant coatings. However, it suffers from brittleness and low ductility when used as a bio-coating material. In this study, a Ta/ZrO2 film was fabricated on Si (100) and titanium alloy substrates using a magnetron sputtering system, with tantalum (Ta) serving solely as a transition layer. Subsequently, Zr and Nb ions were implanted into the film at varying doses but with consistent energy levels. The analysis focused on the film's microstructure, mechanical properties, hydrophilicity, and corrosion resistance. The results demonstrated a significant improvement in the hydrophilicity and corrosion resistance of the ZrO2 film following the implantation of Zr and Nb ions. First-principles calculations based on density functional theory (DFT) principles indicated that, with increasing doping concentrations of Zr and Nb in the ZrO2 model, the stability of the model increased gradually, thereby enhancing its corrosion resistance.

This prospective study aimed to evaluate the ability of point-of-care Doppler ultrasound measurements of carotid-corrected flow time and changes in corrected carotid flow time (FTc) induced by volume expansion to predict fluid responsiveness in patients undergoing robot-assisted gynecological surgery in a modified head-down lithotomy position. FTc was measured using Doppler images of the common carotid artery before and after volume expansion. The stroke volume index at each time point was recorded using the MostCare instrument. Fluid responsiveness was defined as a stroke volume index ≥10% increase after volume expansion. Half (50%) of the 52 patients responded positively. The areas under the receiver operating characteristic curves measured to predict fluid responsiveness for the corrected carotid flow time and changes in the FTc were 0.82 [95% confidence interval:0.705–0.937; P < 0.0001] and 0.67 (95% confidence interval:0.520–0.815; P < 0.05), respectively. The optimal cut-off value for the FTc and the change in FTc were 356.5 ms and 19.5 ms, respectively. FTc is a more reliable predictor of fluid responsiveness than FTc induced by volume expansion in gynecological patients undergoing robot-assisted laparoscopic surgery in the modified head-down lithotomy position.

Soil aggregates, as the basic component of soil, make great contributions to the stability of soil structure and soil carbon (C) sequestration. Recently, grassland is experiencing continuous grazing, which greatly affects soil aggregation and soil C storage. However, how soil aggregates and soil C in different grassland respond to grazing remain unclear. In this study, three national fenced grassland monitoring field stations which represented mountain meadow (MM), temperate steppe (TS), temperate steppe desert (TSD) were selected, soil samples at 0–10 cm depth of inside and outside the fence were collected to explore the effect of grazing and grassland type on composition, stability and nutrients of soil aggregates. The results showed that the bulk soil organic carbon (SOC), total nitrogen (TN), total phosphorus (TP), available nitrogen (AN) and available phosphorus (AP) varied greatly among the three grassland types, with the highest values in MM. Soil aggregates composition showed significantly response to both grassland type and grazing, especially the proportion of soil aggregates >2 mm, which significantly decreased 51.68% on average in grazing plots compared with fenced plots, whereas sharply decreased in MM and TSD. A significant decrease (on average 25.08%) of the mean weight diameter (MWD) of soil aggregates under grazing was detected across all grassland types. The effect of grazing on nutrients in macroaggregates (>0.25 mm) was greater than that in microaggregates (<0.25 mm). Aggregate-associated SOC concentration decreased under grazing in MM and TSD, however, SOC density showed different response to grazing across all grassland types, with minor effect on MM, decreasing SOC density in TS and increasing on TSD, respectively. The magnitude of grazing effect size on aggregate-associated SOC varied in different soil particle size, with greater response in aggregates > 2 mm and the biggest value in TDS. In addition, correlation analysis showed that MWD of soil aggregates had significant negative correlation with soil bulk density, but significant positive correlation with SOC, TN and TP concentration. Results of RDA showed that BD, soil nutrients were the main influence factors of the composition and stability of aggregates. Overall, grazing had significant influence on soil aggregation, stability and SOC, played a crucial role in grassland soil stability and the accumulation of SOC.

Many research work has demonstrated that taken the Combined Cooling Heating and Power system (CCHP) as the core equipment, the integrated energy system (IES) can bring obvious benefit to energy efficiency, CO2 emission reduction and operation economy in urban areas. Compared with isolated IES, integrated energy micro-grid (IEMG) which is formed by connecting multiple regions IES together, through distribution and thermal network, can further improve the reliability, flexibility, cleanliness and economy of regional energy supply. Based on the existing IES model, this paper describes the basic structure of IEMG and built a IEMG planning model. The planning based on the mixed integer linear programming, and economically construction planning scheme are calculated by using known electricity, heating and cooling loads information and the given multiple equipment selection schemes. At last, the model is validated by a case study. The results show that the application of IEMG can effectively improve the economy of regional energy supply.

The next-generation communication systems demand integration of sensing, communication, and power transfer (PT) capabilities, requiring high spectral efficiency, energy efficiency, and low cost, while also necessitating robustness in high-speed scenarios. Integrated sensing and communication systems (ISACS) exhibit the ability to simultaneously perform communication and sensing tasks using a single RF signal, while simultaneous wireless information and power transfer (SWIPT) systems can handle simultaneous information and energy transmission, and orthogonal time frequency space (OTFS) signals are adept at handling high Doppler scenarios. Combining the advantages of these three technologies, a novel cyclic prefix (CP) OTFS based integrated simultaneous wireless sensing, communication, and power transfer system (ISWSCPTS) framework is proposed in this work. Within the ISWSCPTS, the CP-OTFS matched filter (MF) based target detection and parameters estimation (MF-TDaPE) algorithm is proposed to endow the system with sensing capabilities. To enhance the system’s sensing capability, a waveform design algorithm based on CP-OTFS ambiguity function shaping (AFS) is proposed, which is solved by iteratively method. Furthermore, to maximize the system’s sensing performance under communication and PT Quality of Service (QoS) constraints, a semidefinite relaxation (SDR) beamforming design (SDR-BD) algorithm is proposed, solved using through SDR technique. Simulation results demonstrate that the ISWSCPTS exhibits stronger parameter estimation performance in high-speed scenarios compared to orthogonal frequency division multiplexing (OFDM), waveform designed by CP-OTFS AFS demonstrates superior interference resilience, and beamforming designed by SDR-BD strikes a balance in the overall performance of the ISWSCPTS.

Magnetometric Resistivity(MMR) Method, which can use the power supply method of the traditional apparent resistivity method to measure the magnetic field. At present, the application research abroad is relatively extensive, but the domestic(China) research on the application of the MMR method is very few, and it is not even well-known. This paper is based on the MMR theoretical method under the point source DC condition, combined with the abnormal potential method and the modified Biot-Savart law, and using the three-dimensional numerical calculation method of the finite difference method to calculate the abnormal potential field, electric field, and magnetic field on the matlab2018a platform. Calculate, realize the multi-physics simulation in the electromagnetic field through Matlab platform programming, and verify the correctness of the algorithm by the spherical anomaly model with an analytical solution. Through the visual simulation of the three-dimensional data volume of the multi-physics field in the electromagnetic field, we can better understand the response mechanism of the electromagnetic field under DC conditions and grasp their three-dimensional spatial distribution rules. It is hoped that the research in this article can help the research of MMR Personnel better use this method for exploration.

Carbon dioxide (CO2)miscible fracturing huff and puff technology plays a pivotal role in enhancing the recovery rate of crude oil, particularly in reservoirs with challenging physical properties, strong water sensitivity, high injection pressure, and complex water injection dynamics. In this study, the oil-increasing mechanism and huff and puff effect of CO2 miscible fracturing fluid are investigated through a comprehensive experimental approach. Specifically, experiments on PVT gas injection expansion, minimum miscible pressure, and CO2 miscible fracturing huff and puff are conducted on the G fault block reservoir in J Oilfield. The findings demonstrate that injecting CO2 into reservoirs leads to oil volume expansion, viscosity reduction, and saturation pressure increase. Additionally, the inclusion of solubilizers and viscosity reducers further enhances the efficiency of crude oil extraction. Solubilizers not only improve oil recovery but also reduce the minimum miscible pressure required for effective CO2 dispersion. Furthermore, the shut-in time, permeability, and huff and puff method all have considerable impacts on huff and puff recovery rate. This study offers valuable technical insights, supporting the application of CO2 miscible fracturing huff and puff technology to enhance oil recovery in low-permeability reservoirs.

In China, there is an increasing need for greater genetic diversity in maize (Zea mays L.) germplasm and hybrids appropriate for mechanical harvesting. In order to test and distinguish American maize inbred lines with exceptional combining ability, four Chinese maize inbred lines (Chang7-2, Zheng 58, four-144 and four-287) were used to judge the combining ability and heterosis of 16 USA inbred lines by a NCII genetic mating method. The results showed that among the American inbred lines, 6M502A, LH208, NL001, LH212Ht, PHW51, FBLA and LH181 expressed good GCA for yield characteristics; while RS710, PHP76, FBLA, and PHJ89 showed excellent GCA for machine harvesting characteristics. Five hybrids (NL001 × Chang7-2, LH212Ht × Chang7-2, FBLA × four-144, LH181 × four-287, PHK93 × four-287) had better SCA values for yield characteristics, at 1.69, 1.07, 1.48, 1.84 and 1.05, respectively; while NL001 × Chang 7-2, 6M502A × Chang7-2, LH212Ht × Chang7-2, LH181 × four-287, PHW51 × Chang7-2 had better TCA values for yield characteristics, at 3.03, 2.80, 2.41, 2.19 and 1.91, respectively; NL001 × Chang7-2, 6M502A × Chang7-2, LH212Ht × Chang7-2, LH181 × four-287, PHW51 × Chang7-2 showed excellent Control Heterosis values, with 21.48%, 19.64%, 15.93%, 14.05% and 11.60% increases, respectively, compared to the check and potential for future utilization in Inner Mongolian corn production.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

Pancreatic neuroendocrine tumors (PNETs) are characterized by dysregulated signaling pathways that are crucial for tumor formation and progression. The efficacy of traditional therapies is limited, particularly in treatment of PNETs at advanced stage. Epigenetic alterations profoundly impact the activity of signaling pathways in cancer development, offering potential opportunities for drug development. There is currently a lack of extensive research on epigenetic regulation in PNETs. To fill this gap, we first summarize major signaling events which are involved in PNET development. Then, we discuss the epigenetic regulation of these signaling pathways in the context of both PNET and commonly occurring, and therefore more extensively studied, malignancies. Finally, we will offer perspective on the future research direction of PNET epigenome and its potential applications in patient care.

Most natural language processing (NLP) tasks operate an input sentence as a sequence with token-level embeddings and features, despite its clausal structures. Taking Abstract Meaning Representation (AMR) parsing as an example, recent parsers are empowered by Transformers and pre-trained language models, but long-distance dependencies (LDDs) introduced by long sequences are still open problems. We argue that LDDs are not superficially blamed on the sequence length but are essentially related to the internal clause hierarchy. Typically, non-verb words in a clause cannot depend on words outside, and verbs from different but related clauses have much longer dependencies than those in the same clause. With this intuition, we introduce a type of clausal feature, hierarchical clause annotation (HCA), into AMR parsing and propose two HCA-based approaches, HCA-based self-attention (HCA-SA) and HCA-based curriculum learning (HCA-CL), to integrate HCA trees of complex sentences for addressing LDDs. We conduct extensive experiments on two in-distribution (ID) AMR datasets (AMR 2.0 and AMR 3.0) and three out-of-distribution (OOD) ones (TLP, New3, and Bio). Experimental results show that our HCA-based approaches achieve significant and explainable improvements against the baseline model and outperform the state-of-the-art (SOTA) model when encountering sentences with complex clausal structures that introduce most LDD cases.

As the application of cyber-physical systems (CPSs) becomes more and more widespread, its security is becoming a focus of attention. Currently, there has been much research on the security defense of the physical layer of the CPS. However, most of the research only focuses on one of the aspects, for example, attack detection, security state estimation or recovery control. Obviously, the effectiveness of security defense targeting only one aspect is limited. Therefore, in this paper, a set of security defense processes is proposed for the case that a CPS containing multiple sensors is subject to three kinds of stealthy attacks (i.e., zero-dynamics attack, covert attack, and replay attack). Firstly, the existing attack detection method based on improved residuals is used to detect stealthy attacks. Secondly, based on the detection results, an optimal state estimation method based on improved Kalman filtering is proposed to estimate the actual state of the system. Then, based on the optimal state, internal model control (IMC) is introduced to complete the recovery control of the system. Finally, the proposed methods are integrated to give a complete security defense process, and the simulation is verified for three kinds of stealthy attacks. The simulation results show that the proposed methods are effective.

An optimal scheduling strategy for cooling, heating and power (CCHP) joint-power-supply system is proposed to improve energy utilization and minimize costs in this paper. Firstly, the mathematical model of CCHP system is established. Particle swarm optimization (PSO) is used to optimize the regularization coefficient C and the kernel parameter λ which can affect the prediction accuracy of KELM(PSO-KELM). Then PV generation and load prediction model are established by PSO-KELM. In order to jump out of local optimal solution, Cauchy variation is introduced in SFLA local update, and adaptive mutation operation is carried out on SFLA individuals. The predictions of PV generation and load power by PSO-KELM are imported into the objective function, and the microgrid dispatching model is solved by the improved SFLA algorithm. Compared with the traditional GA-KELM and KELM, PSO-KELM has faster convergence and prediction accuracy. Compared with the power supply division, the operation cost of the power grid is reduced by the proposed optimization dispatching strategy of CCHP micro-grid.

Human disturbances can have severe environmental impacts on freshwater ecosystems. The main aim of this study was to detect the influences of physiochemical variables, land-cover characteristics, and river connectivity on fish assemblages in Lake Chaohu Basin, China. A cluster analysis of the river connectivity variables identified four groups of sites that characterized by significantly different connectivity gradients in local scale. These four groups of sites showed increasing connectivity from the upper reaches to the lower reaches. At the same time, among the four groups, the values of the environmental variables generally increased from the upper reaches with less human activity towards the lower reaches with more human activities. For instance, some main physiochemical variables (e.g., river width, water depth, nitrate, phosphate) significantly increased among the four groups. In contrast, fish taxa richness and diversity indices were not significantly different among the four connectivity groups. However, fish assemblages showed significant variation among the connectivity groups (p=0.026). In addition, the study determined that upper riparian land uses (e.g., woodland and grassland), flow velocity, and elevation were environmental variables regulating the variance in the fish communities, and for the connectivity variables, only river order and number of branches along a path to the left of the main stem affected the variance in the fish communities. Therefore, new practices aimed at maintaining and even increasing the riparian canopy coverage and the flow velocity of rivers should be integrated into local conservation planning for freshwater ecosystems, especially in the upper reaches of the basin.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

Second messengers, cyclic adenosine 3'-5'-monophosphate (cAMP) and cyclic guanosine 3'-5'-monophosphate (cGMP) are playing important roles in many animal cells by regulating intracellular signaling pathways and modulating cell physiology. Environmental cues like temperature, light and chemical compounds can stimulate cell surface receptors and trigger the generation of second messengers and the following regulations. Spread of cAMP and cGMP is further shaped by cyclic nucleotide phosphodiesterases (PDEs) for orchestration of intracellular microdomain signaling. However, localized intracellular cAMP and cGMP signaling requires further investigation. Optogenetic manipulation of cAMP and cGMP offers new opportunities of spatio-temporally precise study of their signaling mechanism. Light-gated nucleotide cyclases are well developed and applied for cAMP/cGMP manipulation. Recently discovered rhodopsin phosphodiesterase gene from protists established new and direct biological connection between light and PDEs. Light-regulated PDEs are under development and of demand to complete the toolkit of cAMP/cGMP manipulation. In this review, we summarize the state of the art, pros and cons of artificial and natural light-regulated PDEs and discuss potential new strategies of developing light-gated PDEs for optogenetic manipulation.

In order to solve the interference of narrowband in the ultra-wideband (UWB) system, a high isolation of multiple-input multiple-output (MIMO) antenna is investigated in this paper. The MIMO antenna consists of 2 or 4 UWB elements; and each UWB antenna element is a monopole reconstructed with 2-notched slots, a U-shaped and inverted U-shaped slots etched on the monopole patch to achieve notch characteristics in WIMAX and ITU bands. The property of a 2-element MIMO antenna is analyzed firstly, which is put into a same substrate in parallel. Two rectangular branches are located in the middle to reduce the coupling. Then a 4-element MIMO antenna is studied to meet big size space and more application scenarios. Each element is placed orthogonally on the same substrate; and the isolation is implemented by a cross-shaped branch located in the middle of elements. Both MIMO antenna samples have been tested to verify the design. Measured results show that the working bandwidth is 2.45-14.88 GHz and 2.14-14.95 GHz, the isolation is greater than 17 dB and 20 dB, the peak gain is 5.7 dB and 5.9 dB, the max-imum radiation efficiency can reach 96% and 95%, the envelope correlation coefficient is less than 0.02 and 0.05 for the 2- and 4-element UWB MIMO antenna, respectively. They both are with very good omnidirectional characteristic with notched bands such as the WIMAX and ITU, and meet the requirements of the UWB application in most cases.

Ruminant animals naturally emit methane gas owing to anaerobic microbial fermentation in the rumen, and these gases are considered major contributors to global warming. Scientists worldwide are attempting to minimize methane emissions from ruminant animals. Some of these attempts include the manipulation of rumen microbes using antibiotics, synthetic chemicals, dietary interventions, probiotics, propionate enhancers, stimulation of acetogens, manipulation of rumination time, vaccination, and genetic selection of animals that produce low methane (CH4). The majority of synthetic additives are harmful to both beneficial rumen microbes and the host or only temporarily affect methanogenesis. Phytogenic feed additives (PFAs) have recently emerged as the best alternatives to antibiotics and synthetic chemicals because of growing public concerns regarding drug resistance and the negative impacts of antibiotics and synthetic chemicals on humans, livestock, and the environment. These additives reduce methane production and improve the volatile fatty acid profile. In this review, we provide an overview of PFA sources and how their bioactive components affect the rumen microbiome to reduce methane emissions. Additionally, we highlight the mechanisms of action of PFAs as a whole as well as some of their bioactive components.

A recent study found that a 3ppb increase in O₃ ambient concentration was associated with an increased progression of 0.18 percentage points in percent emphysema and that such increase was equal to smoking 20 cigarettes per day for 29 years. A simple estimation of population attributable fraction shows that COPD diagnoses due to smoking are actually 30 times more than those attributed to a 3 ppb increment in O₃ concentration. Labelling ozone pollution as the new smoking may distort perception of the risks and hinder proper response to real life threatening risk such as smoking.