Fire behavior of natural rubber latex foam under different thickness conditions(d=1,2and 5cm)were explored though a little of experiments by using the self-built small scale experimental platform. It can be shown that the flame spread law of thermally thin and thermally thickness are different. Natural rubber latex foam with thickness of 2cm show higher fire risk, which value of flame spread rate, maximum flame height, maximum mass loss rate and maximum temperature is 0.00293m/s, 851.875mm, 1.83g/s, 948K,repectively.That may because the thickness of residue formed of thermally thick materials is larger than the thin one, obstructing the contact of the natural rubber latex foam with fresh air .In addition, a special phenomenon is noticed that during the second stage, the bottom unburned zone located in the four edges(thermally thin material) and middle player(thermally thick material).

Green and low-carbon development has become an important embodiment of China's path to becoming a strong agricultural country. How to enable agricultural enterprises to better adopt green technologies and conduct production and operation with the concept of sustainable development has become a key link. This article utilizes a structural equation model (SEM) to analyze the role paths and mediating effects of organizational learning ability and policy orientation in agricultural enterprises' market orientation and willingness to adopt green technologies[ The definition of green technology in this paper refers to Guo Kesha, Tian Xiaoxiao. Green technology and green transformation of industrial development mode [J]. Tianjin Social Sciences, 2024 (02) :99-107, including green manufacturing (production) technology and green service technology.]. The results show that market orientation, organizational learning ability, and policy effectiveness have significant direct positive impacts on the willingness to adopt; market orientation has a significant positive impact on agricultural enterprises' organizational learning ability, organizational learning ability has a significant positive impact on policy orientation, and market orientation has a significant positive impact on policy effectiveness; the results of mediation analysis also indicate that learning ability has a significant mediating effect between market orientation and willingness to adopt, and policy effectiveness has a significant mediating effect between market orientation and willingness to adopt. Through difference analysis, it is believed that the mediating effects of the three paths are equally important, and organizational learning ability and policy effectiveness play a partial mediating role in agricultural enterprises' willingness to adopt green technologies. Based on this, policy suggestions are proposed to improve enterprises' own organizational learning ability, increase the promotion of policies related to green technologies, improve relevant policies for the application of green technologies, and increase research and development efforts for green technologies.

There have been relatively few researches that determine the role of bricolage in mediating the empirical relationship between strategic flexibility and product innovation. However, most of the research has studied strategic flexibility to engage the absorptive capacity and facilitate product innovation. The Bricolage approach emphasizes utilizing existing resources in product innovation and explores the mechanisms behind bricolage. A resource-based approach to product innovation involves combining resources in the development process in a concrete manner. This is a groundbreaking study since it is the first to examine empirically how absorptive capacity affects product innovation through bricolage and the serial mediation of strategic flexibility. As a consequence of presenting our results, we concluded that absorptive capacity positively and significantly influences product innovation through the serial mediation of strategic flexibility and bricolage. For strategic flexibility to play a role in supporting product innovation, bricolage is one of the mechanisms that can be utilized. This study contributes to the literature on strategic flexibility by examining the effect of strategic flexibility on bricolage and product innovation from the standpoint that absorptive capacity enhances the strategic flexibility of high-tech SMEs in China. Furthermore, this research offers new insights into the relationship between absorptive capacity and product innovation. In addition, it also provides insight into the economic opportunities that may result from product innovation in transition economies such as China.

Aquaculture by-products can be compromised an important liming material of increasing soil pH and soil fertility. The aim of this research was to assess the effect of mussel shells on soil pH, on organic matter and on soil nutrients. In this study a pot experiment was carried out at the De-partment of Ichthyology and Aquatic Environment (University of Thessaly, Greece). A acidic soil (pH 4.26) amended with 6 different proportions of mussel shell (0.0, 0.1, 0.3, 0.5, 1, 3 and 6%) in two different grain sizes (Fine powder (>1 mm) and Coarse powder (1-2 mm)), resulting in 13 treatments. According to the results, it was observed that pH, organic matter, Available P and Exchangeable K increased. Specifically, the highest pH values observed at 6% rate. Available P and Exchangeable K achieved the highest content at 6% Fine powder treatment, 46.2 and 190.1 mg kg-1, respectively. Similarly, organic matter had the highest value in 6% Fine powder pots (2.27%). Moreover, Total N concentration varied from 0.11 to 0.14 but no statistically significant different was noticed between the treatments. In conclusion, mussel shells can compose a promising liming material in the agriculture section.

Few studies have examined the role of mediating mechanisms played by bricolage in the relationship between strategic flexibility and new product development, even though most of the studies view strategic flexibility as a capability to cope with environmental turbulence and promote product innovation. The bricolage approach embraces the resource-based understanding of the product development process as a concrete process of recombining resources in the process and exploring the mechanisms behind the bricolage approach. This study is the first of the kind that has examined the empirical effect of environmental turbulence on new product development through serial mediation of strategic flexibility and bricolage. Based on our results, environmental turbulence positively and significantly affects new product development through the serial mediation of strategic flexibility and bricolage. Bricolage is one of the mechanisms by which strategic flexibility may play a part in supporting product innovation. Our contribution to strategic flexibility research comes from examining the effect of strategic flexibility on bricolage and new product development from the point that environmental turbulence compels the high-tech industries to remain strategically flexible for their sustainability and growth. Besides providing new evidence on the relationship between environmental turbulence and product innovation, this research also provides new insight into the economic opportunity of new product development in transition economies such as China.

The objective of this research is to establish a better understanding of the current landscape of digital learning research and sustainable development by using CiteSpace. First, we retrieved published publications from the Web of Science (2004–2022). Following that, we examined the primary research strengths and important subjects of digital learning from two perspectives: collaboration networks (including collaborative networks across countries, institutions, and authors) and co-citation networks. We examined the co-citation network from three perspectives: cluster analysis, the most active citers, top references. Furthermore, referenced journals, popular themes, and rising trends were examined. These findings indicate the primary study subjects in the field of digital learning, the most intriguing research literature, and each period's emerging research hotspots. Finally, we proposed further study ideas for future paths.

Aedes aegypti (L.) is the primary vector of chikungunya, dengue, yellow fever and Zika viruses. The leucine-rich repeats (LRR)-containing domain is evolutionarily conserved in many proteins associated with innate immunity in invertebrates and vertebrates, as well as plants. We focused on the AaeLRIM1 and AaeAPL1 gene expressions in response to Zika virus (ZIKV) and Chikungunya virus (CHIKV) infection using a time course study, as well as the developmental expressions in the eggs, larvae, pupae, and adults. RNA-seq analysis data provided 60 leucine-rich repeat related transcriptions in Ae. aegypti in response to Zika virus (Accession number: GSE118858, https://www.ncbi.nlm.nih.gov/gds/?term=GSE118858). RNA-seq analysis data showed that AaeLRIM1 (AAEL012086-RA) and AaeAPL1 (AAEL009520-RA) were significantly upregulated 2.5 and 3-fold during infection by ZIKV 7-days post infection (dpi) of an Ae. aegypti Key West strain compared to an Orlando strain. The qPCR data showed that LRR-containing proteins AaeLRIM1, AaeAPL1 and five paralogues were expressed 100-fold lower than other nuclear genes, such as defensin, during all developmental stages examined. Together, these data provide insights into transcription profiles of LRR proteins of Ae. aegypti during its development and in response to infection with emergent arboviruses.

As the increase threat of flood risk and environmental safety due to the urbanization, Sponge city research has been attracting extensive attention both in practical and theoretical research field. To date, there are only scattered studies about Sponge city. Moreover, vary names of Sponge city prevalent in different countries, which leads to disconnection of literature in the same field of Sponge city. In this paper, a thorough systematic literature mining of Sponge city is presented. A literature analysis system is created, which includes literature export from Web of Sciences and systematic analysis via NoteExpress and CiteSpace. Some literature statistical results are derived. Challenges and opportunities for future research are anticipated. Our goals are to promote this promising thought, summarize past research, and identify issues for future research to create impacts on the practice of Sponge city.

In the Northeast of Portugal, like in many parts of the world, most soils are acidic, which may hamper crop productivity. This study presents the findings of a factorial experiment involving three factors: i) soil type [schist (Sch) and granite (Gra)]; ii) cultivars [Cobrançosa (Cob) and Arbequina (Arb)]; and iii) fertilizer treatments [liming (CaCO3) plus Mg (LMg), P application (+P), B application (+B), all fertilizing materials combined (Con+), and an untreated control (Con-)]. Dry matter yield (DMY) did not show significant differences between cultivars, but plants grown in schist soil exhibited significantly higher biomass compared to those in granite soil. Among the treatments, +B and Con+ resulted in the highest DMY (50.8 and 47.2 g pot-1, respectively), followed by +P (34.3 g pot-1) and Con- (28.6 g pot-1). Treatment LMg yielded significantly lower values (15.6 g pot-1) than Con-. LMg raised the pH above 7 (7.36), leading to a severe B deficiency. Although Con+ also raised the pH above 7 (7.48), it ranked among the most productive treatments for providing B. Therefore, when applying lime to B-poor sandy soils, moderate rates are advised to avoid inducing a B deficiency. Additionally, it seems prudent to apply B after lime application.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

To effectively estimate airport terminal area capacity and assess the maximum throughput the sector can achieve when the capacity is given, this research proposes an approach to assess the terminal area capacity from the viewpoint of service provision resources. Terminal area capacity is optimized based on the equilibrium of air traffic service resource supply and demand. The supply-demand nexus is examined in consideration of terminal area route structure, traffic flow characteristics, and safety regulations. A flight service probability matrix and a terminal area demand and supply service time model are constructed to quantify resource expenditure at varied capacity levels. A optimization model is then developed to apportion maximal capacity under resource limitations. Model computation and computation results demonstrate the deviation between estimated and amended capacities is under 0.3 flight sorties per hour. The outcomes are congruent with historical statistics, thereby validating the accuracy and reliability of the model proposed in this study. Given capacity parameters, the model can deduce the maximal aircraft quantity served concurrently in terminal areas during peak periods. These revelations indicate the submitted model furnishes theoretical foundation and reference for terminal area sector partition and traffic alerting.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

Background: Colorectal cancer (CRC) is one of the major causes of cancer-related death worldwide. Aerobic glycolysis precedes obtainment of oncogenic mutations and loss of tumor suppressors, promoting the progress of CRC. Although numerous biomarkers have been identified to be associated with prognosis and survival, a glycolysis-related gene signature in CRC has not been explored. Methods: mRNA expression profiling data in a group of CRC patients (n = 540) was extracted from the Cancer Genome Atlas (TCGA). Gene set enrichment analysis (GESA) was performed to identify gene sets that were significantly different between CRC tissues and normal tissues. Cox proportional hazards regression models were used to identify genes significantly associated with overall survival. Multivariate Cox regression analysis was used to establish a prognostic risk parameter formula. Kaplan–Meier survival estimates and the log-rank test were used to validate the significance of risk parameters for prognosis prediction. Results: Five glycolysis-related genes (ENO3, GPC1, P4HA1, IDUA, ANKZF1) were identified to be significantly associated with overall survival (AUC=0.754). Based on the five‑gene signature, patients with CRC were divided into high and low‑risk subgroups. CRC patients with a low-risk score had better survival benefits than those with a high one (P < 0.001). Conclusions: A five-gene signature associated with glycolysis for predicting the outcome of CRC patients was generated, serving as a valuable prognosis model with high efficiency and potential targeted therapy of CRC patients.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

This study presents an innovative analytical method for the detection and quantification of 14 β-agonists in pork using liquid chromatography-tandem mass spectrometry (LC-MS/MS). The method involves the use of a solid phase microextraction (SPME) probe, consisting of a wooden tip coated with polyacrylonitrile (PAN) and molecularly imprinted polymer (MIP). This probe has been integrated into an automated extraction device, designed in our laboratory to extract the target analytes prior to LC-MS/MS analysis. Compared to the traditional solid-phase extraction (SPE) procedure, the proposed approach significantly reduces the costs related to adsorbent ma-terial and solvent consumption, and shortens purification time, thereby reducing both the tech-nical workload and associated expenses. The methodology has been carefully validated in ac-cordance with the National Standard of the People's Republic of China (GB/T 22286-2008), evalu-ating key parameters including the limit of detection (LOD), limit of quantification (LOQ), matrix effects, linearity, and both intra-day and inter-day precision. The average recovery rates for all β-agonists were observed to lie between 71.6% and 82.2%, with relative standard deviations (RSDs) consistently below 15% for both types of precision. The LOD and LOQ values were found to range from 0.09 to 0.39 μg/kg and 0.27 to 0.99 μg/kg, respectively. In terms of accurate detection of positive samples, the developed method demonstrated a closer approximation to the true value of the sample compared to the National Standard method GB/T 31658.22-2022. Overall, the proposed method exhibits substantial promise for the routine assessment of β-agonists in pork and presents a practical alternative for compliance monitoring in regulatory settings.

The genus Flavivirus includes 53 members and poses a big threat to human health among worldwide. Diseases caused by flavivirus infections can be broadly classified into hemorrhagic diseases (Dengue, Yellow fever, etc) and neurological diseases (West Nile disease, Zika disease, etc). Many flaviviruses still lack specific treatments and effective vaccines. In this context, it becomes particularly important to thoroughly characterize the pathogenesis of flavivirus infection and develop animal models. Therefore, animal models that can accurately simulate human diseases are essential for evaluating the effectiveness of therapeutic drugs and preventive vaccines. In this paper, we provide a comprehensive review of the currently available animal models that support flavivirus infection and exhibit clinical manifestations related to flavivirus infection. Additionally, we discuss the strengths and limitations of each animal model, aiming to enhance researchers understanding of the use of animal models in flavivirus research. This insight is intended to facilitate further studies into the pathogenesis of flavivirus, as well as the development of antiviral agents and vaccines.

Diagnosing congenital heart disease (CHD) remains challenging because of its complex morphology. Representing the intricate structures of CHD on conventional two-dimensional flat screens is difficult owing to wide variations in the pathologies. Technological advancements, such as three-dimensional printed heart models (3DPHM) and virtual reality (VR), could potentially address the limitations of viewing complex structures using conventional methods. This study aimed to investigate the usefulness and clinical value of four visualization modalities across three different cases of CHD, including ventricular septal defect, double outlet right ventricle, and tetralogy of fallot. Seventeen cardiac specialists were invited to participate in this study, which was aimed at assessing the usefulness and clinical value of four visualization modalities, namely, DICOM images, 3DPHM, VR, and 3D PDF. Of these modalities, 76.4% of the specialists ranked VR as the best for understanding the spatial associations among cardiac structures and for presurgical planning. Meanwhile, 94.1% ranked 3DPHM as the best modality for communicating with patients and their families. Of the various visualization modalities, VR was the best tool for assessing anatomical locations and vessels, comprehending the spatial relationships among cardiac structures, and for presurgical planning. The 3DPHM models were the best tool for medical education as well as communication. In summary, both 3DPHM and VR have their own advantages and outperform the other two modalities, i.e., DICOM images and 3D PDF, in terms of visualizing and managing CHD.

Cs2NaInCl6 double perovskites, which have excellent photoelectric conversion properties and are non-toxic and lead-free, have recently attracted much attention. In particular, double perovskite quantum dots (QDs) are considered to be a promising material for optoelectronic device applications. Ligands such as oleic acid (OA) and oleylamine (OAm) are essential for the synthesis of perovskite QDs, but their roles on double perovskite QDs are not yet clear. In this study, we have investigated the binding of OA and OAm to Cs2NaInCl6 QDs through FTIR and NMR and their effects on the surface defect reduction and stability improvement for Cs2NaInCl6 QDs. We found that only OAm was bound to the QD surfaces while OA was not. The OAm has a great effect on photoluminescence quantum yield (PLQY) improvement by passivate the QD surface defects. The stability of the QDs was also investigated, and it was shown that OA played a significant role in the stability of the QDs. Our findings provide critical insights into the roles of the ligands for photophysical properties and stability of lead-free double perovskite QDs.

The accumulation of foam cells in arterial intima and the accompanied chronic inflammation are considered major causes of neoatherosclerosis and restenosis. However, both the underlying mechanism and effective treatment for the disease are yet to be uncovered. In this study, we combined transcriptome profiling of restenosis artery tissue and bioinformatic analysis to reveal that NLRP3 inflammasome is markedly upregulated in restenosis and that several restenosis re-lated DEGs are also targets of mulberry extract, a natural dietary supplement used in traditional Chinese medicine to improve liver vitality. Further pathway enrichment analysis identified MAPK signaling pathway to be involved in the inflammatory response of foam cells. Consistently, immunofluorescence microscopy shows co-localization of NLRP3 with CD68+ macrophages. We then evaluated the efficacy of mulberry extract in inhibiting both the formation of foam cells and their inflammatory response. We demonstrated that mulberry extract suppresses the formation of ox-LDL induced foam cells, possibly by upregulating the cholesterol efflux genes ABCA1 and ABCG1 to inhibit intracellular lipid accumulation. In addition, mulberry extract dampens NLRP3 inflammasome activation by stressing the MAPK signaling pathway. Collectively, our mecha-nistic and functional studies unveil the therapeutic value of mulberry extract in neoatherosclerosis and restenosis treatment by regulating lipid metabolism and inflammatory response of foam cells.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

Flexible capacity applications demands to large energy storage density and high breakdown electric field strength of flexible films. Here, P(VDF-HFP) with ultra-thin Al2O3 nanosheets composite films were designed and fabricated through an electrospinning process followed by hot-pressing in sandwich structured. The results show that the insulating ultra-thin Al2O3 nanosheets and the sandwich structure can enhance the composites' breakdown field (by 24.8%) and energy density (by 30.6%) remarkedly to P(VDF-HFP) polymer matrix. An energy density of 23.5 J/cm3 at the ultrahigh breakdown field of 740kV/mm can be therefore realized. Insulating test and phase-field simulation results reveal that ultra-thin nanosheets insulating buffer layers can reduce the leakage current in composites, thus it effects the electric field spatial distribution to enhance breakdown strength. Our research provides a feasible method to increase the breakdown strength of ferroelectric polymers, which is comparable to those of non-ferroelectric polymers.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

In this paper, we propose a novel approach of video skimming by exploiting the fusion of video temporal information and keyword information representation extracted from multi-model video information including audio, text and visual indices. In addition, we introduce the brand-safe filtering and sentiment analysis in order to only reserve the user-friendly content in the video skim. In the experiment by using the videos from YouTube-8M dataset, we have proved that the semantic conservation in the video skim from the proposed approach highly outperforms the approaches by only partial information of the video in conserving the semantic content of the video.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

Background: Functional Movement Screening (FMS) allows for rapid assessment of an individual’s physical activity level and timely detection of sports injury risk. However, traditional functional movement screening often requires on-site assessment by experts, which is time-consuming and prone to subjective bias. Therefore, the study of automated functional movement screening has become increasingly important. Methods: In this study, we propose an automated assessment method for FMS based on the improved Gaussian Mixture Model (GMM). First, the oversampling of minority samples is conducted, the movement features are manually extracted from the FMS dataset collected with two Azure Kinect depth sensors, then we train the Gaussian mixture model with different scores (1 point, 2 points, 3 points) of feature data separately, finally, we conducted FMS assessment by the Maximum Likelihood estimation. Results: The improved GMM has a higher scoring accuracy (Improved GMM:0.8) compared to other models (Traditional GMM=0.38, Adaboost.M1=0.7, Naïve-Bayes=0.75), and the scoring results of improved GMM have a high level of agreement with the expert scoring (kappa=0.67). Conclusions: The results show that the proposed method based on the improved Gaussian mixture model can effectively perform the FMS assessment task and it is potentially feasible to use depth cameras for FMS assessment.

Metamorphosis is a critical process for most anurans to transition from water to land. The appearance of air-breathing lungs occurs during the change in oxygen medium from water to air. Revealing the structural construction and molecular switches of lung organogenesis is essential to understand the realization of air-breathing function. In this study, histology and transcriptomics were combinedly conducted to explore these issues in Microhyla fissipes lungs during metamorphosis. During the pro-metamorphic phase, histological structure improving of the alveolar wall was accompanied by robust substrate metabolism and protein turnover. The lungs, at the metamorphic climax phase, are characterized by an increased number of cilia in the alveolar epithelial cells and collagenous fibers in the connective tissues, corresponding to the transcriptional upregulation of cilia and extracellular matrix-related genes. The post-metamorphic lungs strengthen the contracting function, as suggested by the thickened muscle layer and the upregulated expression of genes involved in muscle contraction. The blood–gas barrier is fully developed in adult lungs whose transcriptional features are tissue growth and differentiation regulation and immunity. Importantly, significant transcriptional switches of pulmonary surfactant protein and hemoglobin facilitate air-breathing. Our results illuminated four key steps of lung development for amphibians to transition from water to land.

The increasing residential space differentiation is an important practical problem for Chinese cities. The different choice of living space for urban residents is a concrete reflection of social class divide, which reflects the differences in the choices and demands of different social groups for urban housing. Taking Wuhan, an important city in central China, as an example, this research divides the residential space based on the social resource structure, and analyzes and compares the spatial differentiation and influencing factors of different residential areas and houses with different prices in Wuhan by spatial differentiation indicators and geographic detector. The results show clear differences in resource structure among residential areas, and there are few high-quality residential areas with a concentrated distribution. The spatial differentiation levels of different residential areas are distinct, and the pursuit of high-quality and scarce resources is the key to the residential space differentiation of most large cities in China. In addition, residential space differentiation can lead to inter-generational problems such as housing wealth inequality, resource deprivation and solidified class identity. Exploring the mechanisms and social effect of residential space differentiation in most large cities in China can provide some reference for China's urban space planning and real estate market regulation in the new era.

Long-span steel structure trusses are widely used in factory buildings, but with the growth of service time and the increase of dynamic load fatigue, a considerable part of the long-span truss with dynamic load appears serious transverse cracks at the bottom of the middle span and oblique deformation of the abdomen in the operation process. The U-shaped cracks at the bottom and belly, as well as the mid-span down deflection of the main truss, reduced the functional function of the factory building truss structure, and had to limit the original crane load, which affected the normal safety and durability of the structure. Therefore, the application principle of the variable axial force cable system in the long-span factory building truss structure and 3D3S software modeling [1] were used. Analyzing and studying the reinforcement method of large-span powerhouse truss can provide practical experience for subsequent similar projects. In view of the above phenomenon, the large-span powerhouse trusses of Hongcheng Powerhouse 1 and No.2 located in Tonglu, Zhejiang Province are used as the research object, and the variable axial force cable method is proposed to strengthen and lift the load. Considering the span of large-span powerhouse truss, the cable system with 22m controlling force of 400kN is proposed to be selected for powerhouse 1, and the cable system with variable axial force of 24m is proposed to be selected for Powerhouse 2. The force model of large-span truss is established by using the finite element method commonly used to analyze the force of truss. Under two working conditions, The influence of reinforcement effect is analyzed and compared from three aspects: stiffness, bearing capacity and stability. And the phenomenon of uneven stress distribution is analyzed. The stress distribution characteristics of each node are understood by simulating the most disadvantageous node plates with the greatest internal force before and after reinforcement.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

On the primitive Earth, both L- and D-amino acids would have been present. However, only L-amino acids are essential blocks to construct proteins in modern life. To study the relative stability of D-amino acid substituted peptides, a variety of computational methods were applied. Ten prebiotic amino acids (Gly, Ala, Asp, Glu, Ile, Leu, Pro, Ser, Thr, and Val) were previously determined by multiple meteorite, spark discharge, and hydrothermal vent studies. Some previously reported early Earth polypeptide analogs were focused on in this study. Tripeptides composed of only Asp, Ser, and Val exemplified that different positions (i.e., N-terminus, C-terminus, and middle) made a difference in the minimal folding energy of peptides, while the chemical classification of amino acid (hydrophobic, acidic, or hydroxylic) did not show a significant difference. Hierarchical cluster analysis for dipeptides with all possible combinations of the proposed ten prebiotic amino acids and their D-amino acid substituted derivatives generated five clusters. Primordial simple polypeptides were modeled to test the significance of molecular fluctuations, secondary structure occupancies, and folding energy differences based on these clusters. We found peptides with α-helices, long β-sheets, and long loops are usually less sensitive to D-amino acid replacements in comparison to short β-sheets. Intriguingly, amongst 129 D-amino acid residues, mutation sensitivity profiles presented that the ratio of more to less stable residues was about 1. In conclusion, some combinations of a mixture of L- and D-amino acids can potentially act as essential building blocks of life.

This paper introduces a novel ensemble adjustment Kalman filter (EAKF) that integrates a machine-learning approach. The approach employs nonlinear variable relationships established by a deep neural network (DNN) during the analysis stage of the EAKF. This process nonlinearly projects observation increments into the state variable space. The newly developed DNN-EAKF algorithm can be applied to coupled data assimilation using coupled ocean-atmosphere models. It enhances cross-component updates in strongly coupled data assimilation (SCDA) by diminishing errors in estimating cross-component error covariance arising from insufficient ensemble members, thereby improving the SCDA analysis. This paper employs a conceptual model to conduct twin experiments, validating the DNN-EAKF’s capability to utilize cross-component observation information in SCDA effectively. The approach is anticipated to offer insights for future methodological integrations of machine learning and data assimilation and provide methods for SCDA applications in coupled general circulation models.

We study theoretically the Josephson diode effect (JDE) realized in a system composed of parallel-coupled double quantum dots (DQDs) sandwiched between two semiconductor nanowires deposited on an s-wave superconductor surface. Due to the combined effects of the proximity-caused superconductivity, strong Rashba spin-orbit interaction and Zeeman splitting inside the nanowires, a pair of Majorana bound states (MBSs) may possibly emerge at opposite ends of each nanowire. Different phase factors arisen from the superconductor substrate can be generated in the coupling amplitudes between the DQDs and MBSs prepared at the left and right nanowires, and will result in the Josephson current. We find that the critical Josephson currents in positive and negative directions are different from each other in amplitude within an oscillation period with respective to the magnetic flux penetrating through the system, a phenomenon known as the JDE. It arises from the quantum interference effect in this double-path device, and can hardly occur in system of one QD coupled to MBSs. Our results also show that the diode efficiency can reach up to 50%, and depends on the overlap amplitude between the MBSs and the energy levels of the DQDs adjustable by gate voltages. The present model is realizable within current nanofabitication technologies and may find practical use in interdisciplinary field of Majorana and Josephson physics.

Viral integration within the host genome plays a pivotal role in carcinogenesis. Various disruptive mechanisms are involved, leading to genomic instability, mutations, and DNA damage. With next-generation sequencing (NGS), we can now precisely identify viral and host genomic breakpoints and chimeric sequences, which are useful for integration site analysis. In this study, we evaluated a commercial hybrid-capture NGS panel specifically designed for detecting three key viruses: HPV, HBV, and HIV-1. We also tested workflows for Viral Hybrid Capture (VHC) and Viral Integration Site (VIS) analysis, leveraging customized viral databases in CLC Microbial Ge-nomics. By analyzing sequenced data from virally infected cancer cell lines (including SiHa, HeLa, CaSki, C-33A, DoTc2, 2A3, SCC154 for HPV; 3B2, SNU-182 for HBV; and ACH-2 for HIV-1), we precisely pinpointed viral integration sites. The workflow also highlighted disrupted and neigh-boring human genes that may play a crucial role in tumor development. Our results included in-formative virus-host read mappings, genomic breakpoints, and integration circular plots. These visual representations enhance our understanding of the integration process. In conclusion, our seamless end-to-end workflow bridges the gap in understanding viral contributions to cancer development, paving the way for improved diagnostics and treatment strategies.

The central coast is one of the importantly livable regions in China, and green land plays a meaningful role in improving human settlements through regulating ecosystem services. However, the research on spatiotemporal heterogeneity of green land in different urbanized areas are still lacking in this region, which limits the timeliness of reporting on the land-surface thermal properties of residential environment from green land perspective. To address this issue, the synergistic methodology of “artificial numerical technology -- urban interior mixed pixel classification -- surface radiation energy balance model” was applied to investigate the green land change and its impact on human settlements in Rizhao region, which is known for its coastal ecology and greenery in China and obtained the United Nations habitat award. Main conclusions of this study are below: (1) Although total green land decreased by 474.05 km2, resulting in a decrease of 9.17% in its share of the entire study area from 2000-2022 during the urbanization process, but the greening levels improved within the built-up area, with the greening proportion of 25.34% in 2000 and 42.98 km2 in 2022. (2) Differences in green land at different urbanized regions were first observed, namely, urban greening rate was 37.78% in the old urban areas of 2022, while it was up to 46.43% in new urban areas. More attention was paid to the construction of urban green space during urban expansion, which will inevitably bring better visual and comfort experience to residents. (3) Thermal comfort indicators for urban residents were evaluated in latent heat flux (0-457.83 W/m2), sensible heat flux (0-645.09 W/m2), total available energy (254.07-659.42 W/m2) and others. (4) The lowered cooling temperature effect in the middle, high green land density region was 1.05 ℃ and 2.12 ℃ compared to the low-density region, and the average air temperature was 25.86 ℃. Also, spatial patterns of hot and cold uncomfortable areas were displayed in this study. Overall, this study provides the meaningfully practical reference for exploring the spatiotemporal heterogeneity of green land and its impact on residents' environments from the perspective of land-surface thermal properties in coastal areas of China and around the world.

The Subtropical Front (STF) plays a key role in the ecology of Chilean jack mackerel Trachurus murphyi. Nonetheless, there are few remote sensing studies of the STF in the open Southeast Pacific Ocean, and almost all of them have been conducted by satellite oceanographers in Russia and Ukraine to support respective large-scale fisheries of jack mackerel in this region. We reviewed these studies that documented long-term seasonal and interannual variability of the STF from sea surface temperature (SST) and sea surface height (SSH) data. We also mapped the STF from satellite sea surface salinity (SSS) data of the SMOS mission (2012-2019). The Subtropical Front consists of two fronts -- North and South STF about 500 km apart -- that border the Subtropical Frontal Zone (STFZ) in-between. The STF is density-compensated, with spatially divergent manifestations in temperature and salinity. In the temperature field, the STF extends in the WNW to ESE direction in the Southeast Pacific. In the salinity field, the STFZ appears as a broad frontal zone, extending zonally between 30-35°S across the entire South Pacific. Three major types of satellite data – SST, SSH, and SSS – can be used to locate the STF. The SSH data is most advantageous with regard to the jack mackerel fisheries owing to the all-weather capability of satellite altimetry and the radical improvement of the spatial resolution of SSH data in the near future. Despite the dearth of dedicated in situ studies of the South Pacific STFZ, there is a broad consensus regarding the STFZ being the principal spawning and nursing ground of T. murphyi as well as a major migration corridor between Chile and New Zealand.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for 15-5PH Stainless steel by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as concentration of cutting fluid , temperature of cutting fluid , feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error and material removal rate, the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, concentration of cutting fluid, radial depth of cut and temperature of cutting fluid. Finally, confirmation tests were carried out to make a comparison between the experimental results and developed model. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

Intramuscular fat content (IFC) and meat color are vital indicators affecting pork quality. A significant positive correlation between IFC and redness meat color (a* value) indicates that these two traits are likely to be regulated by shared molecular pathways. To identify candidate genes, hub genes, and signaling pathways that regulate these two traits, we measured the IFC and a* value in 147 hybrid pigs and selected individuls with extreme phenotypes for transcriptome analysis. The results revealed 485 and 394 overlapping differentially expressed genes (DEGs) using DESeq2, limma, and edgeR packages affecting IFC and a* value, respectively. Weighted gene co-expression network analysis (WGCNA) identified four modules significantly correlated with IFC and a* value. Moreover, we integrated functional enrichment analysis results based on DEGs, GSEA, and WGCNA conditions to identify candidate genes, and identified 47 and 53 candidate genes affecting IFC and a* value, respectively. The protein-protein interaction (PPI) network analysis of candidate genes showed that 6 and 14 hub genes affecting IFC and a* value, respectively. These genes mainly participated in various pathways related to lipid metabolism and redox reactions. Notably, four crucial hub genes (MYC, SOX9, CEBPB, and PPAGRC1A) were shared for these two traits. After functional annotation of these four hub genes, we hypothesized that the SOX9/CEBPB/PPARGC1A axis could co-regulate lipid metabolism and myoglobin redox response. Further research on these hub genes, especially the SOX9/CEBPB/PPARGC1A axis, will help to understand the molecular mechanism of the co-regulation of IFC and a* value, which will provide the theoretical basis for improving pork quality.

In order to maintain the best conditions of the building from the first day of opening, explorations of office buildings in the world investigated the approaches of optimizing the building operation and property facilities, whereas building managers often have trouble prioritizing improvements toward their sustainable objectives. The challenge is due to numerous equipment types in the building, which has various durability in years and represents users’ different feelings of importance and satisfaction. When faced with multiple improvement projects, building managers are often unable to determine the order of implementation.Hence, this research applies the Analytic Hierarchy Process (AHP) using TAIPEI 101 Tower as a case study to explore the key factors affecting tenants’ willingness to lease office buildings by distributing questionnaires to real estate experts. By filtering out key indicators related to property facilities that users care about, this study used Importance and Satisfaction Analysis (IS Analysis) to identify items that need urgent improvement. The research revealed that air conditioning is the top priority for improvement through empirical evaluation and weight ranking. This study hopes to establish an evaluation model for facility improvements to help clarify the prioritization and defeat limited resources to projects effectively, which is helpful for sustainable property management.

Unmanned Aerial Vehicles (UAVs) image object detection has great application value in military and civilian fields. However, the objects in the captured images from UAVs have problems of large scale variation, complex backgrounds, and a large proportion of small objects. To resolve these problems, a multi-scale object detector based on coordinate and global information aggregation is proposed, named CGMDet. Firstly, a Coordinate and Global Information Aggregation Module (CGAM) is designed by aggregating local, coordinate, and global information, which can obtain features with richer context information. Secondly, a Multi-Feature Fusion Pyramid Network (MF-FPN) is proposed, which can better fuse features of different scales and obtain features containing more context information through repeated use of feature maps, to better detect multi-scale targets. Moreover, more location information of low-level feature maps is integrated to improve the detection results of small targets. Furthermore, we modified the bounding box regression loss of the model to make the model more accurately regress the bounding box and faster convergence. Finally, the proposed CGMDet was tested on VisDrone and UAVDT datasets and mAP0.5 of 50.9% and 48% was obtained, respectively. At the same time, our detector achieved the best results compared to other detectors.

In past years, lithium-ion batteries (LIBs) can be found in every aspect of life, and batteries, as energy storage systems (ESSs), need to offer electric vehicles (EVs) more competition to be accepted in markets for automobiles. Thick electrode design could reduce the use of non-active materials in batteries that its energy density would be improved and its cost would be cut. However, thick electrodes are limited by their weak mechanical stability and poor electrochemical performance, these limitations could be classified as the critical cracking thickness (CCT) and the limited penetration depth (LPD). The understanding of the CCT and the LPD have been proposed and the recent works on breaking the CCT and improving the LPD are listed in this article. By comprising these attempts, some thick electrodes could not offer higher mass loading or higher accessible areal capacity that would defeat the purpose.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

We investigate numerically the interactions of in-phase Airy beams modulated by a fundamental Gaussian beam and fourth-order diffraction in Kerr nonlinear media. Directly numerical simulations show that normal (anomalous) fourth-order diffractions and in-phase (out-of-phase) Gaussian beam affect the interactions of solitons generated from Airy beams in unique manners. Different from previous results that interactions between in-phase (out-of-phase) conventional beams are always attractive (repulsive), many anomalous interactions of Airy beams are obtained. Stable bound states of breathing Airy soliton pairs can be formed with the help of fourth-order diffraction and fundamental Gaussian beam.

Background: Lung cancer is one of the leading causes of morbidity and mortality worldwide with 25% of deaths due to lung cancer occurring in Europe. This study therefore sought to assess the burden of lung cancer by country and to evaluate the magnitude of fine Particulate Matter (PM2.5) and cigarette smoking by country in Europe. Methods: An ecological study nested on the World Health Organization air pollution database 2016 was conducted. We sampled 30 European Countries, with a total of 1625 mean annual samples of Particulate Matter (PM2.5) collected from 1625 designated sites (n = 1625). We further used the ‘World Health Disease Rankings’ database to extract Lung Cancer Morbidity and Mortality Rate by country. We used SAS version 9.4 to indicate the distribution of PM2.5 and Lung Cancer Mortality Rate. Results: Lung cancer Relative Risk (RR) was 1.0 in all never- smokers. RR for Ex-smokers for Adeno carcinoma was 3.5 in males and 1.1 in females, small cell carcinoma was 16.2 in males and 3.8 in females. RR for current smokers for Adeno carcinoma was 8.0 in males and 4.1 in females, small cell carcinoma was 57.9 in males and 18.2 in females. Mean annual PM2.5 by country ranged from 6.01 to 37.28µg/m3 whereas lung cancer mortality rate by country ranged from 19.67 to 54.26 deaths per 100,000 population. Conclusion: Cigarette smoking and exposure to both second hand smoke and high concentration of PM2.5 resulted into increased burden of lung cancer in Europe. Countries should re-strategize to reduce the burden of lung cancer in Europe.

Land use and cover change (LUCC) is an important method to investigate the causes of global environment change. We utilized the emergy ecological footprint (EEF) model to construct a land-use change model to be used as a systematic measuring tool for monitoring sustainable development trends. In particular, we estimated the eco-security of the Cing-jing region as a case study so that responsible agencies can use it to maintain a balance between ecological preservation and tourism development. The results indicated the following: First, the ecological environment of the Cing-jing region satisfied the safety standard in 2008–2014; however, the related indices increased considerably. Second, the grey model predicted a decrease in 2015–2024 ecological carrying capacities of Cing-jing and a large increase in capita EFs, resulting in a larger ecological deficit and higher EFI. The eco-security from 2015–2024 was higher compared to 7 years ago and is predicted to reach the Grade 2 intermediate level in 2022; thus the Cing-jing region is gradually becoming ecologically unsustainable. Strengths of our study included the use of EEF theory in a quantitative analysis of slope lands for the effective evaluation of ecological security. Finally, we expanded our research to include ecological security issues.

High-spin states of 192Tl are populated by the heavy ion fusion-evaporation reaction 181Ta(16O, 5n)192Tl at 97 MeV beam energy. A new level scheme with eight new levels is constructed and the level spins are tentatively assigned. The negative-parity yrast band is extended up to 23^{-}\hbar. Subsequently, the systematics of signature splitting and signature inversion are discussed for the negative-parity yrast band of odd-odd Tl isotopes including 192Tl, 194Tl, 196Tl, and 198Tl. With the increase of neutron number signature inversion is found in 196,198Tl at high-spin state in these four Tl isotopes. The reason may be due to the competition between neutron-proton interaction and Coriolis force.

In recent years, many molecular and environmental factors have been studied to understand how synaptic plasticity is modulated. Sleep, as an evolutionary conserved biological function, has shown to be a critical player for the consolidation and filtering of synaptic circuitry underlying memory traces. Although sleep disturbances do not alter normal memory consolidation, they may reflect fundamental circuit malfunctions that can play a significant role in exacerbating diseases, such as autism and Alzheimer’s disease. Very recently, scientists sought to answer part of this enigma and they identified p75 neurotrophic receptor (p75NTR) as a critical player in mediating impairments in hippocampal-dependent associative plasticity upon sleep deprivation. This paper will review the role of the p75NTR, critically discuss the impact and implications of this research as the bridge for sleep research and neurological diseases.

Based on stochastic frontier analysis and translog input distance function, this paper examines the total factor energy efficiency of China’s industry using input-output data of 30 sub-industries from 2002 to 2014, and decomposes the changes in estimated total factor energy efficiency into the effects of technical change, technical efficiency change, scale efficiency change and input-mix effect. The results show that during this period the total factor energy efficiency in China’s industry grows annually at a rate of 3.63%, technical change, technical efficiency change and input-mix effect contribute positively to the change in total factor energy efficiency, while scale efficiency change contributes negatively to it.

Electromagnetic sensing has been used for diverse applications of non-destructive testing, including the surface inspection, measurement of properties, object characterization. However, the measurement accuracy could be significantly influenced by the lift-off between sensors and samples. To address the issue caused by lift-offs, various strategies have been proposed for the permeability measurement of ferromagnetic steels, which mainly involves different sensor designs and signal features (e.g., the zero-crossing feature). In this paper, a single high-frequency scenario for the permeability retrieval is introduced. By combining the signal of two sensing pairs, the retrieval of magnetic permeability is less affected by the lift-off of sensors. Unlike the previous strategy on reducing the lift-off effect (directly taking the phase term out of the integration) using the Dodd-Deeds analytical method, the proposed method is based on a high-frequency linear feature of the phase term. Therefore, this method has the merit of high accuracy and fast processing for the permeability retrieval (a simplified version of Dodd-Deeds analytical formulas after the integration). Experimental measurement has been carried out on the impedance measurement of designed sensors interrogating ferromagnetic dual-phase steels. For sensor lift-offs of up to 10 mm, the error of the permeability retrieval is controlled within 4 % under the optimal frequency.

Eddy current testing can be used to interrogate steels but it is hampered by the lift-off distance of the sensor. Previously, the lift-off point of intersection (LOI) feature has been found for the pulsed eddy current (PEC) testing. In this paper, a lift-off invariant inductance (LII) feature is proposed for the multi-frequency eddy current (MEC) testing, which merely targets the ferromagnetic steels. That is, at a certain working frequency, the measured inductance signal is found nearly immune to the lift-off distance of the sensor. Such working frequency and inductance are termed as the lift-off invariant frequency (LIF) and LII. Through simulations and experimental measurements of different steels under the multi-frequency manner, the LII has been verified to be merely related to the sensor parameters and independent of different steels. By referring to the LIF of the test piece and using an iterative inverse solver, one of the steel properties (either the electrical conductivity or magnetic permeability) can be reconstructed with a high accuracy.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

The connected vertex cover (CVC) problem is a variant of the vertex cover problem, which has many important applications, such as wireless network design, routing and wavelength assignment problem, etc. A good algorithm for the problem can help us improve engineering efficiency, cost savings and resources in industrial applications. In this work, we present an efficient algorithm GRASP-CVC (Greedy Randomized Adaptive Search Procedure for Connected Vertex Cover) for CVC in general graphs. The algorithm has two main phases, i.e., construction phase and local search phase. To construct a high quality feasible initial solution, we design a greedy function and a restricted candidate list in the construction phase. The configuration checking strategy is adopted to decrease the cycling problem in the local search phase. The experimental results demonstrate that GRASP-CVC is competitive with the other competitive algorithm, which validate the effectivity and efficiency of our GRASP-CVC solver.

Land engineering is a specific new academic discipline in China. Although the undergraduate major of land engineering was officially approved and established lately since 2017, the birth of land engineering as an academic discipline dates back 40 years ago. It has passed through four development stages: the incubation stage in 1978-1985, the initial stage in 1986-1997, the growth stage in 1998-2011, and the expanding stage from 2012 to present. However, land engineering as an academic discipline remains immature and seriously lags behind practice. There are still no unified academic community and broad academic consensus. After a historical overview of the four development stages, this study gave a strategic consideration to five key questions. We argue that the study object of the discipline is land engineering activity, which is defined as the artificial transformation of a land complex combined by various natural and human elements. The uniqueness of the discipline is rooted in its ability to study the comprehensive and integrated reorganization or rebuilding of various elements of land as a complex, with the theory of land complex reconstruction being the core theory. The discipline of land engineering is based on land pure science and land technology, and is one basis of land management. It consists of two modules (rural land engineering and urban land engineering), five secondary disciplines of each module (land development, land rearrangement, land improvement, land protection, and land remediation), and more than 30 research directions. Various technologies are only instrumental but not essential components of land engineering as an academic discipline.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.

There is no doubt that seagrass beds constitute one of the most productive ecosystems in shallow coastal waters. Despite this, picoplankton in seagrass ecosystems has received relatively little attention. The purpose of this study was to compare picoplankton growth and mortality rates between seagrass and unvegetated habitats using chamber incubations. We tested two main hypotheses: (i) incubation with seagrass would result in higher bacterial growth rates due to increased DOM release from seagrass photosynthesis, and (ii) Synechococcus spp. would be lower in the presence of seagrass due to competition for inorganic nutrients. Our results showed bacterial growth rates of 2.31 and 2.44 d–1 without and with seagrass, respectively. In seagrass chambers, bacterial growth was higher than that in non-seagrass chambers, suggesting that organic carbon coming from the seagrass community may support bacterial production. Furthermore, we observed a negative Synechococcus spp. growth rate (-0.9 d–1) in the seagrass treatment, likely reflecting nutrient competition with the seagrass. Small-scale chambers proved to be a useful tool for studying the factors controlling spatial and temporal patterns of picoplankton across different habitats. Furthermore, future studies should examine picoplankton growth over a wider range of spatial scales in seagrass beds and adjacent unvegetated sediment.

This paper proposes a new approach for multi-focus images fusion based on Region Mosaicing on Contrast Pyramids (REMCP). A density-based region growing method is developed to construct a focused region mask for multi-focus images. The segmented focused region mask is decomposed into a mask pyramid, which is then used for supervised region mosaicking on a contrast pyramid. In this way, the focus measurement and the continuity of focused regions are incorporated and the pixel level pyramid fusion is improved at the region level. Objective and subjective experiments show that the proposed REMCP is more robust to noise than compared algorithms and can fully preserves the focus information of the multi-focus images meanwhile reducing distortions of the fused images.

In view of the Practical Byzantine Fault Tolerance (PBFT) consensus algorithm all nodes participate in the consensus, the three-stage process has problems such as large communication overhead, random selection of master nodes and lack of reward and punishment mechanism. A Speculative Practical Byzantine Fault Tolerance (SP-PBFT) is proposed. Firstly, the consensus protocol was optimized, and a timeout mechanism was proposed to divide the consensus process into optimistic mode and pessimistic mode, which reduced the communication overhead under the premise of resisting Byzantine node attacks .Secondly, a node evaluation mechanism was proposed to calculate the node reputation value according to the node's historical behavior and give the corresponding reward or punishment, which reduced the possibility of malicious nodes participating in the consensus process. Finally, the Fibonacci grouping mechanism was used to reduce the number of nodes participating in the consensus process, fundamentally improving the consensus efficiency, avoiding the problem of centralization of the consensus process caused by the cumulative reputation value of nodes, and improving the enthusiasm of consensus nodes. Simulation experiments using Docker containers to simulate multiple nodes show that the SP-PBFT consensus algorithm proposed in this paper has better performance than PBFT consensus algorithm and other improved algorithms in terms of consensus delay, throughput, fault tolerance and communication complexity.

In the recent past, China has experienced rapid urbanization as a result of diverse growth factors. In such a context, it is crucial to evaluate the expansion of urban entities in order to implement sustainable urban planning strategies in China. Since, urban entities are the spatial reflection of the concentration of human activities, the delineation of urban areas upon the boundaries of built-up surfaces has resulted from inconsistent understanding and identification of urban areas. The study has attempted to extract and evaluate the growth of urban entities in 336 prefecture cities in China mainland (2000-2020) upon a novel approach using consistent night light images. The urban entities were extracted using the light intensities of the SNPP-VIIRS-like data. After extracting urban entities, a rationality assessment was carried out comparing derived urban entities with the LandScan population product, Landsat, and road networks. Also, the results were compared with other physical extents products such as MODIS and the HE. According to the findings, urban entities are basically consistent with the LandScan, road networks, and those with the HE and MODIS. But, urban entities accurately reflect the concentration of human activities than impervious extents of MODIS and the HE. At the prefecture levels, urban entities elevated from 8082 km2 to 74,417 km2 between 2000 and 2020 showing a 10.8% growth rate. By providing a supplementary resource and guide for trustworthy urban mapping, the research will expand new research directions that address the issues of variations of NTL data brightness thresholds dynamics on regional, and global scales.

The rapid development of China's economy has led to a rapid increase in energy production and use. Among them, the excessive consumption of coal in fossil energy consumption is the leading cause of air pollution in China. This paper incorporates renewable energy innovation, fossil energy consumption and air pollution into a unified analysis framework, and uses spatial measurement models to investigate the spatial effects of renewable energy green innovation and fossil energy consumption on air pollution in China, and decomposes the total impact into direct and indirect effects. influences. The empirical results show that China's air pollution, renewable energy green innovation and fossil energy consumption are extremely uneven in geographical space, generally showing the characteristics of high in the east and low in the west, and showing a strong spatial aggregation phenomenon. Fossil energy consumption will lead to increased air pollution, and the replacement of fossil fuels with clean and renewable energy is an important means of controlling pollution emissions. The direct and indirect effects of renewable energy green innovation on air pollution are significantly negative, indicating that renewable energy green innovation not only suppresses local air pollution, but also suppresses air pollution in neighboring areas. The consumption of fossil energy will significantly increase the local air pollution, and the impact on the SO2 and Dust&Smoke pollution in the adjacent area is not very obvious. It is recommended to strengthen investment in renewable energy green innovation, reduce the proportion of traditional fossil energy consumption, and pay attention to the spatial connection and spillover of renewable energy green innovation.

Buckypaper (BP), a flexible and porous material, exhibits photovoltaic properties when exposed to light. In this study, we have employed Radio Frequency (RF) Sputtering of Zinc Oxide (ZnO) followed by rapid thermal annealing to enhance the photovoltaic response of BP. We investigated the impact of various sputtering parameters, such as the gas flow ratio of argon to oxygen and deposition time, on the morphology, composition, resistivity, and photovoltaic characteristics of ZnO-modified BP. Additionally, the photovoltaic performance of the samples under different illumination modes and wavelengths was compared. It was found that optimal sputtering conditions—argon to oxygen flow ratio of 1:2, deposition time of 20 minutes, and power of 100 watts—resulted in a ZnO film thickness of approximately 45 nanometers. After annealing at 400°C for 10 minutes, the ZnO-modified BP demonstrated a significant increase in photocurrent and photovoltage, along with a reduction in resistivity, compared to unmodified BP. Moreover, under gradient illumination, the ZnO-modified BP exhibited a photovoltage enhancement of 14.70 times and a photocurrent increase of 13.86 times, compared to uniform illumination. Under blue light, it showed a higher photovoltaic response than under other colors. The enhancement in photovoltaic response is attributed to the formation of a Schottky junction between ZnO and BP, an increased carrier concentration gradient, and an expanded light absorption spectrum. Our results validate that ZnO sputtering followed by annealing is an effective method for modifying BP for photovoltaic applications such as solar cells and photodetectors.

This study employs the phase-field regularized cohesion model (PF-CZM) to simulate crack propagation and damage behavior in porous granite. We investigate how pore radius (r), initial crack-pore distance (D), and pore-crack angle (θ) impact crack propagation. The simulation findings reveal that, with a fixed deflection angle and initial crack-pore distance, larger pores are more likely to induce crack extension under identical loading conditions. Moreover, with r and θ keeping constant, the crack extension can be divided into two stages: from its initiation to the lower edge of the pore and then from the lower edge to the upper boundary of the model. By varying the values of D and r, we derive multiple combinations of different D/r ratios and pore radii. These results demonstrate that with constant r, cracks tend to deflect toward the pore closer to the initial crack. Conversely, when D is maintained constant, cracks will preferentially deflect toward pores with a larger r. In summary, the numerical simulation of rock pores and initial cracks, based on the PF-CZM, exhibits remarkable predictive capabilities and holds significant potential in advancing rock fracture analysis.

Image segmentation is the process of partitioning an image into multiple segments where the goal is to simplify the representation of the image and make the image more meaningful and easier to analyze. In particular, semantic segmentation is an approach of detecting the classes of objects, based on each pixel. In the past, most semantic segmentation models were for only one single style, such as urban street views, medical images, or even Manga. In this paper, we proposed a semantic segmentation model called Dual-Pyramid Wide Residual Network (DPWRN) to solve the segmentation for cross-style datasets, which is suitable for diverse segmentation applications. The DPWRN integrated the Pyramid of Kernel paralleled with Dilation (PKD) and Multi-Feature Fusion (MFF) to improve the accuracy of segmentation. To evaluate the generalization of the DPWRN and its superiority over most state-of-the-art models, three datasets with completely different styles are tested in the experiments. Finally, the DPWRN verified its generalization and also showed its superiority over most state-of-the-art models.

This review will serve as an entry point for international researchers who would like to tap into the vast scientific potential of Chinese-language literature on oceanic fronts. We focused on observational studies in descriptive physical oceanography of marine fronts. A thorough bibliographic search netted 93 papers published in 1982-2023, with a sharp increase of the total number of papers after 2010. This trend continued unabated through the early 2020s. Regionally, the overwhelming majority of papers is focused on the China Seas, particularly the East China Seas (Bohai, Huanghai, and Donghai, especially the Yangtze River Plume) and northern South China Sea (Guangdong Shelf). Elsewhere, a number of papers were dedicated to the Southern Ocean and North Atlantic. Thematically, papers on remote sensing of ocean fronts dominate, with special attention to the development of new advanced front-detection algorithms applied to satellite data on sea surface temperature and chlorophyll. Numerous papers on marine fronts in the China Seas present important results that have to be considered by international researchers. Overall, this review emphasizes the significant contributions made by Chinese oceanographers, particularly to the frontal oceanography of the China Seas.

The purpose of interdisciplinary communication during the early architectural design stage is to achieve the early integration of knowledge in different professional fields, which can help architects to choose correct design development strategies during the early architectural design stage. However, because there is too little information at the early design stage, and design solutions are still rapidly changing and developing, the uncertainties at this stage make it difficult for consultants in other disciplines to provide their views and analysis. In spite of this situation, the emergence of generative modeling is changing design procedures and methods of communication and cooperation for architectural teams, and has brought about a shift in the way architects transmit design information from "what" (declarative information) to "how" (procedural information). Generative modeling is like an aircraft's dashboard: It can provide a basis for interdisciplinary communication, provide interdisciplinary knowledge packages, and bring about a shift in interdisciplinary communication that will reduce the architectural team's communication needs and cost. This study uses a real design case to show the feasibility of generative modeling. Employing generative modeling as a basis, architects can enhance the efficiency of design change and multi-disciplinary communication during the early design stage, integrate specialized knowledge in relevant fields, use this knowledge to formulate design criteria for the next stage, and effectively transmit design decisions. As a consequence, the changes to the cost structure of design revisions and communication between different disciplines has initiated a paradigm shift toward multi-disciplinary communication in architectural design.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

The signal processing technique is one of the principal tools for diagnosing power quality (PQ) issues in electrical power systems. The Discrete Fourier Transform (DFT) is a frequency analysis technique used to process power system signals and identify PQ problems. However, the DFT algorithm may lead to spectral leakage and picket-fence effect problems for asynchronously sampled signals that contain harmonic, inter-harmonic, and flicker components. To resolve this shortcoming, a hybrid method for frequency estimation based on a second-level DFT approach and a frequency-domain interpolation algorithm to obtain the accurate fundamental frequency of a power system is proposed in this paper. This method uses a second-level DFT to compute the cosine and sine parts for the fundamental frequency components of the acquired signals. Then, a frequency-domain interpolation approach is adopted to determine the amplitude ratio for the cosine and sine parts of the system's fundamental frequency. To demonstrate the performance of the proposed frequency estimation method, the observation window used by this paper to evaluate different estimation algorithms is 200 ms. According to the IEC standards, a 200 ms acquisition window is recommended for power system quality assessment. A set of mixed signals with harmonic, inter-harmonic, and flicker components with the fundamental frequency deviation is used. The evaluation results demonstrate the superiority of the new method over other approaches for assessing asynchronously sampled signals contaminated with noise, harmonic, inter-harmonic, and flicker components.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for AA7050-T7451 by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of cutting variables such as, feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error, material removal rate and power consumption the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is proved that the most significant factor is cutting speed, followed by feed rate, radial depth of cut. Finally, confirmation tests were performed to make a comparison between the experimental results. Experimental results have shown that machining performance in precision turn-boring process can be improved effectively through this approach

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for Ti-6Al-4V by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as, feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error, material removal rate and power consumption the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, radial depth of cut. Finally, confirmation tests were carried out to make a comparison between the experimental results. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

Neurogenesis in the adult brain plays a major role in the cognitive ability of animals including learning and memory. Poria cocos (Schw.) Wolf (P. cocos) has been known as a traditional Chinese edible medicinal herb with the potential effect to improve learning and memory. However, the effect mechanisms are still elusive. In this study, significant neuronal differentiation-promoting activities of the ethanol extracts of P. cocos (EEPC) were tested in Neuro-2a cells and mouse cortical neural stem/progenitor cells (NSPCs). Subsequently, 97 compounds of EEPC were identified using UHPLC-Q-Exactive-MS/MS. After investigation of neuronal differentiation-promoting activities of 4 major compounds (Ethyl palmitoleate, L-(-)-Arabitol, Choline and Adenosine), only Choline has significant neuronal differentiation-promoting activity. In summary, we investigated the neuronal differentiation-promoting activity and chemical compositions of EEPC, the study of the neuronal differentiation-promoting effect of ether extract of P. cocos indicated P. cocos’s positive effect on learning and memory functions. This is the first investigation of the neuronal differentiation-promoting effect of ether extract of P. cocos based on similar research references.

Immunoglobulin G (IgG) adopts a modular multidomain structure that mediates antigen recognition and effector functions, such as complement-dependent cytotoxicity. IgG molecules are self-assembled into a hexameric ring on antigen-containing membranes, recruiting the complement component, C1q. To provide deeper insights into the initial step of the complement pathway, we report a high-speed atomic force microscopy study for quantitative visualization of the interaction between IgG and the C1 complex composed of C1q, C1r, and C1s. Results showed that C1q in the C1 complex is restricted regarding internal motion and has a stronger binding affinity for on-membrane IgG assemblages than C1q alone, presumably because of smaller conformational entropy loss upon binding. Furthermore, we visualized a 1:1 stoichiometric interaction between C1/C1q and an IgG variant that lacks the entire CH1 domain in the absence of antigen. In addition to the canonical C1q-binding site on Fc, their interactions are mediated through a secondary site on the CL domain that is cryptic in the presence of the CH1 domain. Our findings offer clues for novel-modality therapeutic antibodies.

Next-generation sequencing (NGS) has actualized human papillomavirus (HPV) virome profiling for in-depth investigation of viral evolution and pathogenesis. However, viral computational analysis remains a bottleneck due to semantic discrepancies between computational tools and curated reference genomes. To address this, we developed and tested automated workflows for HPV taxonomic profiling and visualization using a customized Papillomavirus database in CLC Microbial Genomics Module. HPV genomes from Papilloma Virus Episteme were customized and incorporated into CLC “ready-to-use” workflows for stepwise data processing to include: 1) Taxonomic Analysis, 2) Estimate Alpha/Beta Diversities, and 3) Map Reads to Reference. Low-grade (n = 95) and high-grade (n = 60) Pap smears were tested with ensuing collective runtimes: Taxonomic Analysis (36 min); Alpha/Beta Diversities (5 sec); Map Reads (45 min). Tabular output conversion to visualizations entailed 1-2 keystrokes. Biodiversity analysis between low- (LSIL) and high-grade squamous intraepithelial lesions (HSIL) revealed loss of species richness and gain of dominance by HPV-16 in HSIL. Integrating clinically relevant, taxonomized HPV reference genomes within automated workflows proved to be an ultra-fast method of virome profiling. The entire process named “HPV DeepSeq” provides a simple, accurate and practical means of NGS data analysis for a broad range of applications in viral research.

RFID based technology innovated a new field of wireless sensing, which has been applied in posture recognition, object localization and the other sensing fields, the existing sensing methods often require tags to be attached to dynamic targets (because RFID signals are more sensitive to moving target), significantly limiting their applications. It is a challenging task to sensing a static target without tag attached in NLOS (Non-Line-of-Sight). We utilized RFID technologies to sense the static foreign objects in agricultural products, and taken metal, rock, rubber and clod as sensing targets that are common in agricultural. By deploying a tag matrices to create a sensing region, we observed the signal variations before and after the appearance of the targets in this sensing region, determined the targets’ positions and their types. Here, we buried the targets in the media of seedless cotton and wheat, and detected static targets with a non-contact method in the NLOS. Researches illustrated that by deploying appropriate tag matrices and adjusting the angle of a single RFID antenna, the matrices signals can be sensitive to the static targets’ positions and their properties,i.e. matrices signals vary with different targets and their positions. Specifically, we achieved a 100% success rate in locating metallic targets, while the success rate for clods was the lowest at 86%. We achieved a 100% recognition rate for the types of all the four objects.

Accurate detection of players and teams in ice hockey games is crucial to the tracking of individual players on court and team tactical decisions, which is therefore becoming an important task for coaches and other analysts. However, hockey is a fluid sport due to complex dynamics and frequent substitutions by both teams, resulting in various body positions of players. Few traditional player detection models from other team sports take these characteristics into account, especially for the detection of teams without prior annotations. Here, we design a two-phase cascaded Convolutional Neural Network (CNN) model coupling between individual players position information and team uniform colors to hierarchically detect players in ice hockey games. Our model filters most of disturbing information, such as audience and sideline advertising bars, in Phase I, and refines the detection of targeted players in Phase II, which is efficient and accurate with a precision rate of 91.30% and a recall rate of 95.60% for individual players detection, and an average accuracy of 93.05% in team classification from a self-built dataset of collected images in the 2018 Winter Olympics. Meanwhile, we also present results based on the images and real-time detection from broadcasting videos of 2019-20 NHL regular games covering all 31 teams to show the robustness of our model.

Highly-correlated electrons – electrons that engage in strong electron-electron interactions – have been observed in transition metal oxides and quantum dots and can create unusual material behavior that is difficult to model, such as switching between a low resistance metal state and a high resistance Mott insulator state. Tests of devices using a layer-by-layer deposition process for forming multilayer arrays of ferritin (a transition metal (iron) oxide storage protein) have been previously reported that indicate that highly-correlated electron transport is occurring, consistent with models of electron transport in quantum dots. This paper reports the results of the effect of various degrees of structural homogeneity on the electrical characteristics of these ferritin arrays, as well as demonstrating that these structures can provide a switching function associated with the circuit that they are contained within, consistent with the observed behavior of highly-correlated electrons.

A partial aperture onboard calibration method can solve the onboard calibration problems of some large aperture remote sensors, which is of great significance for the development trend of increasingly large apertures in optical remote sensors. In this paper, the solar diffuser reflectance degradation monitor (SDRDM) in the onboard calibration assembly (CA) of the FengYun-4 (FY-4) advanced geostationary radiance imager (AGRI) is used as the reference radiometer for measuring the partial aperture factor (PAF) for the AGRI onboard calibration. First, the linear response count variation relationship between the two is established under the same radiance source input. Then, according to the known bidirectional reflection distribution function (BRDF) of the solar diffuser (SD) in the CA, the relative reflectance ratio coefficient between the AGRI observation direction and the SDRDM observation direction is calculated. On this basis, the response count value of the AGRI and the SDRDM is used to realize the high-precision measurement of the PAF of the AGRI B1 ~ B3 bands by simulating the AGRI onboard calibration measurement under the illumination of a solar simulator in the laboratory. According to the determination process of the relevant parameters of the PAF, the measurement uncertainty of the PAF is analyzed; this uncertainty is better than 2.04% and provides an important reference for the evaluation of the onboard absolute radiometric calibration uncertainty after launch.

Background: Smoking is disproportionately prevalent among Aboriginal and Torres Strait Islander Australian peoples, with 39% of Indigenous Australians aged over 15 years smoking daily. Efforts to reduce this high prevalence include culturally focused media campaigns, designed using community consultation, highlighting the need to determine how such health messaging is received by smokers. This study aimed to examine Indigenous Australian smokers’ reactions to a culturally focused anti-smoking mass media campaign—'Give up Smokes’. Methods: Intercept surveying across health services and events used recorded demographics, smoking status, quit attempts, smoking health effects, anti-smoking campaign recall, social support, and campaign reactions. Participants rated campaign images in five domains: 1) whether it made them stop and think; 2) personal relevance; 3) believability of design and message; 4) prompting concern about smoking; and 5) motivation towards quitting. Cluster analysis was used to segment smoker types. Results: Smoking health effects knowledge was high, and did not differ by quit readiness, attempts, or social support. Cessation support access was higher among those with greater readiness to quit. Social smoking behaviour and confidence to support others quitting did not significantly differ between participants, however importance of others quitting did. Quit readiness, attempts, and social support were associated with reaction to campaign design, but not message recall. Four types of smokers were described, using smoking characteristics, who differed in campaign message reactions. Conclusions: Strategies using campaign-exposed smoker characteristics to inform culturally focused health promotion are discussed in relation to four identified types of smokers.

With the influences of climate change and human activities, the resources and environment of “One Belt and One Road” are facing severe problems and challenges. This study aims to analyze the temporal and spatial dynamics of the drought environment and the response of vegetation cover to the drought by using drought indicators. Gravity Recovery and Climate Experiment (GRACE) drought severity index (GRACE-DSI) and GRACE water storage deficit index (GRACE-WSDI), were calculated to present hydrological drought. Moreover, based on GRACE, Water-Global Assessment and Prognosis (WaterGAP) model, and Global Land Data Assimilation System (GLDAS) data, the groundwater in Central Asia was retrieved to calculate the groundwater drought index called the GRACE Standardized Groundwater Level Index (GRACE-SGI). The results show that the annual precipitation in Central Asia increased slightly at a rate of 0.39 mm/year (p = 0.82) since 2000, while the temperature increased slightly at a rate of 0.05 ℃/year (p = 0.10). The water storage decreased significantly at -0.59 mm/year (p <0.01) and experienced a decrease-increase-decrease process. During the study period, the arid situation in Central Asia deteriorated, especially in the eastern coast of the Caspian Sea and the Aral Sea basin. From 2007 to 2015, the Central Asian environment was generally arid and suffered from different du-rations and degrees of hydrological and groundwater droughts. The drought indicators (i.e., GRACE-DSI, GRACE-WSDI) and the NDVI showed a significantly positive correlation during the growing season. However, the NDVI of cultivated land and grassland distribution areas in Central Asia showed a strong negative correlation with GRACE-SGI. It is concluded that the drought environment in Central Asia affected the growth of vegetation. The continued deterioration of the arid situation may further stress the ecological system in Central Asia.

Hepatocellular carcinoma (HCC) is the fifth most common type of cancer, and is the third leading cause of cancer-related deaths each year. It involves a multi-step progression and is strongly associated with chronic inflammation induced by the intake of environmental toxins and/or viral infections (i.e., hepatitis B and C viruses). Although several genetic dysregulations are considered to be involved in disease progression, the detailed regulatory mechanisms are not well defined. Homeobox (Hox) genes that encode transcription factors with homeodomains control cell growth, differentiation, and morphogenesis in embryonic development. Recently, more aberrant expressions of Hox genes were found in a wide variety of human cancer, including HCC. In this review, we summarize the currently available evidence related to the role of Hox genes in the development of HCC. The objective is to determine the roles of this conserved transcription factor family and its potential use as a therapeutic target in future investigations.

Moral identity can promote people’s well-being, but existing research has paid little attention to the mechanism of the link between the two. The current study proposed that the eudaimonic identity function is a critical mechanism that links moral identity and well-being. Specifically, the quality of identity commitment mediates the link between subjective well-being and the two dimensions of moral identity, namely, internalization and symbolization. We examined these hypotheses in 419 participants, who completed the Self-importance of Moral Identity Questionnaire, Satisfaction with Life Scale, Scale of Positive and Negative Experience, and Questionnaire for Eudaimonic Well-being. Results from the obtained data confirmed our hypotheses: There is a significant correlation between moral identity and subjective well-being. Both the internalization and symbolization dimensions of moral identity promote subjective well-being through the mediating role of identity commitment quality. We discussed these findings with respect to implications and proposed research suggestions for future studies.

Advanced electrode designs have made single-unit neural recordings commonplace among modern neuroscience research. However, single-unit resolution remains out of reach for the intrinsic neurons of the gastrointestinal system. Single-unit recordings of the enteric (gut) nervous system have been conducted in anesthetized animal models and excised tissue, but there is a large physiological gap between awake and anesthetized animals, particularly for the enteric nervous system. Here, we describe the opportunity for advancing enteric neuroscience offered by single-unit recording capabilities in awake animals. We highlight the primary challenges to microelectrodes in the gastrointestinal system including structural, physiological, and signal quality challenges.

BACKGROUND. The aims of this study was to compare differences in daytime sleepiness between genders and qualification levels in a cohort university Chinese soccer player under 0 Covid policy restrictions in the urban area of Shanghai. METHODS. 491 questionnaires of Epworth Sleepiness Scales (ESS) were compiled online by males and females Soccer Students (SS), Semi-professional players (SP) and professional players (PP) during the ongoing measures of Shanghai lockdown. ANOVA was performed for players levels and gender. RESULTS. Significant differences were found between the 3 levels and between males and females. PP showed a very low score in the ESS (5,97) well below the threshold of 8, while SS and SP showed an ESS score above the threshold. Female showed higher scores than males. CONCLUSIONS. This study present the first data on sleepiness in Chinese soccer players of different level of qualification in a lockdown condition. Professional players has been less affected by lockdown measures than SS and SP. We can hypothesize the reasons resides in the more ordered lifestyle of PP in comparison to SS and SP, which mitigated the effects of the lockdown. Measures to improve sleep in females’ soccer player should be adopted.

Due to their strong immersion and real-time interactivity, helmet-mounted VR devices are becoming increasingly popular. Based on these devices, an immersive virtual geographic environment (VGE) provides a promising method for research into crowd behavior in an emergency. However, the current cheaper helmet-mounted VR devices are not popular enough and will continue to coexist with PC-based systems for a long time. Therefore, a heterogeneous distributed virtual geographic environment (HDVGE) could be a feasible solution to solve the heterogeneous problems caused by various types of clients, and support implementation of virtual crowd evacuation experiments, with large numbers of concurrent participants. In this study, we developed an HDVGE framework and put forward a set of design principles to define the similarities between the real world and the VGE. We discussed the HDVGE architecture and proposed an abstract interaction layer, a protocol-based interaction algorithm and an adjusted dead reckoning algorithm to solve the heterogeneous distributed problems. We then implemented an HDVGE prototype system focusing on subway fire evacuation experiments. Two types of clients are considered in the system, PC and all-in-one VR. Finally, we evaluated the performances of the prototype system and the key algorithms. The results showed that in a low-latency LAN environment, the prototype system can smoothly support 90 concurrent users consisting of PC and all-in-one VR clients. HDVGE could serve as a new means of obtaining observational data about individual and group behavior in support of human geography research.

Based on the analysis of the working principle, circuit design and working loss of the common charger DC/DC converter, this paper designs a ZVS half-bridge three-level DC/DC converter based on non-phase-shift control mode, and proposes a multi-stage constant current and voltage limiting charging control strategy based on modulation wave selection control. The simulation results show that the proposed method and control strategy have faster voltage regulation ability and wider stability margin, and can achieve stable current sharing control in the charging process.

The decline in Pinus sylvestris var. mongolica in the introduction area has had a high profile in recent years. For the ecological restoration, management and silvicultural design of Mongolian pines in the introduction area, it is necessary to conduct a comprehensive and in-depth study on the ecological adaptation mechanism of Mongolian pines in provenances. The ecological process of water and nutrient accumulation as well as the influence of environmental factors on the photosynthetic physiology are the key to revealing the ecological adaptation mechanism of Mongolian pines. According to the differences of climate in the distribution area of Mongolian pines, sampling sites were set up, the effects of environmental factors on leaf δ13C and the relationship between leaf δ13C and nutrient content were analyzed. The results showed that leaf δ13C values were ranging from - 29.7 ‰ to - 23.76 ‰. The ecological stoichiometry, including LC (522.81 mg·g-1), LN (16.04 mg·g-1), LP (1.19 mg·g-1) and L-N:P (13.56), indicated that leaf photosynthesis and water use efficiency is greatly affected by environmental conditions, Mongolian pines had strong ability of carbon fixation, and its growth was obviously restricted by nitrogen. Although there was no significant correlation between δ13C with stoichiometric parameters in leaf, photosynthesis was the key link in the process of carbon fixation. It also showed that Pinus sylvestris var. mongolica was a stomatal limited plant. Leaf δ13C had significant correlation with climatic factors. VPD is the dynamic factor affecting the photosynthetic physiological process in leaves. Air and soil moisture are the dominate factors affecting the leaf stomatal conductance and determines leaf δ13C value, while other factors indirectly affect leaf δ13C by its impact on relative humidity or soil water content. Soil phosphorus content affected by clay is a key factor affecting soil water availability and soil nutrient cycling. Photosynthetic process in leaf is the dynamic process affecting the nutrient accumulation.

Fuzzy Rule Interpolation (FRI) offers an innovative methodology for inferring outcomes from data points that match no established rules in a sparse fuzzy rule base. Generally, a traditional fuzzy rule-based system suffers from the inability to perform inference while facing an unmatched observation, given a sparse fuzzy rule base that is derived from insufficient data or inadequate human experience and that fails to cover parts of a specific problem domain. Fortunately, starting with a sparse rule base, Fuzzy Rule Interpolation (FRI) can help to formulate interpolated rules specifically in instances where observations fail to activate any existing rule. An interpolated rule gives a result called consequent, which is related to the unmatched observation so that the inference system will not fail to generate an outcome corresponding to the observation as the output. Conventionally, these interpolated rules will be discarded after obtaining outcomes. However, valuable information may be potentially embedded within those discarded rules addressing the limitation regarding the coverage of the original sparse knowledge space. Moreover, without exploiting the potential value of the interpolated rules, the fuzzy inference system based on a sparse rule base will never improve its efficiency and robustness in the long run. Therefore, this underscores the necessity for Dynamic Fuzzy Rule Interpolation (D-FRI), which aims to collate interpolated rules that cover particular knowledge spaces absent in the sparse rule base. Intuitively, those frequently appeared interpolated rules are considered valuable because future observations are more likely to hit the respective problem areas. Promoting selected interpolated rules to the sparse rule base can enhance the overall coverage of the knowledge space and increase the inference efficiency over time. This paper introduces a framework for Dynamic Fuzzy Rule Interpolation that integrates the widely used Transformation-based Fuzzy Rule Interpolation (T-FRI) with an effective form of clustering of interpolated results. Experimental findings validate the effectiveness of this approach.

Time series data having low signal-to-noise ratio, non-stationarity and non-linearity are commonly seen in high-frequency stock trading, where the objective is to increase the likelihood of profit by taking advantage of tiny discrepancies in prices and trading on them quickly and in huge quantities. For this purpose, it is essential to apply a trading method that is capable of fast and accurate prediction from such time series data. In this paper, we develop an online time series forecasting method for high-frequency trading (HFT) by integrating three neural network deep learning models, i.e., Long Short-Term Memory (LSTM), Gated Recurrent Unit (GRU) and Transformer; and we abbreviate the new method to online LGT or O-LGT. The key innovation underlying our method is its efficient storage management, which enables super-fast computing. Specifically, when computing the forecast for the immediate future time, we use only the output calculated from the previous trading data (rather than the previous trading data themselves) together with the current trading data. Thus, the computing involves updating only the current data into the process. We evaluate the performance of O-LGT by analyzing the high-frequency Limit Order Book (LOB) data from the China market. It shows that our model in most cases achieves similar speed with much higher accuracy than the conventional fast supervised learning models for HFT. However, with a slight sacrifice in accuracy, O-LGT is approximately 40 times faster than the existing high-accuracy neural network models for the LOB data in China market.

Recently, a layer-stacked ESN model named deep echo state Network (DeepESN) has been established. As an interactional model of recurrent neural network and deep neural network, investigations of DeepESN are of significant importance in both areas. Optimizing the structure of neural networks remains a common task in artificial neural networks, and the question of how many neurons should be used in each layer of DeepESN must be stressed. In this paper, our aim is to solve the problem of choosing the optimized size of DeepESN. Inspired by the sensitive iterative pruning algorithm, a neuronal similarity-based iterative pruning merging algorithm (NS-IPMA) is proposed to iteratively prune or merge the most similar neurons in DeepESN. Two chaotic time series prediction tasks are applied to demonstrate the effectiveness of NS-IPMA. The results show that the DeepESN pruned by NS-IPMA outperforms unpruned DeepESN with the same network size, and NS-IPMA is a feasible and superior approach to improving the generalization performance of DeepESN.

Eye movements support memory encoding by binding distinct elements of the visual world into coherent representations. However, the role of eye movements in memory retrieval is less clear. We propose that eye movements play a functional role in retrieval by reinstating the encoding context. By overtly shifting attention in a manner that broadly recapitulates the spatial locations and temporal order of encoded content, eye movements facilitate access to, and reactivation of, associated details. Such mnemonic gaze reinstatement may be obligatorily recruited when task demands exceed cognitive resources, as is often observed in older adults. We review research linking gaze reinstatement to retrieval, describe the neural integration between the oculomotor and memory systems, and discuss implications for models of oculomotor control, memory, and aging.

The Sugarcane yellow leaf virus (SCYLV) is associated with sugarcane yellow leaf disease (SCYLD) and is considered to be the most economically deleterious emerging pathogen that represents a potential threat and danger to sugarcane cultivation in China. Over the last two decades, high genetic diversity in the SCYLV genotypes was observed worldwide, with a greater chance of YLD incidence for sugarcane injury. SCYLV infection has significantly damaged its economic traits and is responsible for substantial losses in biomass production in sugarcane cultivars. This study aims to identify and comprehensively analyze sugarcane microRNAs (miRNAs) as therapeutic targets against SCYLV using plant miRNA prediction tools. Mature sugarcane miRNAs are retrieved and are used for hybridization of the SCYLV. A total of seven common sugarcane miRNAs were selected based on consensus genomic positions. The biologically significant, top ranked ssp-miR528 was consensually predicted to have a potentially unique hybridization site at nucleotide position 4162 for targeting the ORF5 of the SCYLV genome; this was predicted by all the algorithms used in this study. Then, the miRNA–mRNA regulatory network was generated using the Circos algorithm, which was used to predict novel targets. There are no acceptable commercial SCYLV-resistant sugarcane varieties available at present. Therefore, the predicted biological data offer valuable evidence for the generation of SCYLV-resistant sugarcane plants.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

Passive marine listening, involving the acoustic monitoring of underwater environments, has become increasingly vital for scientific research, environmental monitoring, and defense applications. However, the success of such applications critically depends on the ability to extract meaningful information from the often noisy and dynamic underwater acoustic environment. In this context, Mel-frequency cepstral coefficients (MFCCs) have emerged as an essential tool for feature extraction, capturing the spectral characteristics of marine sounds and making them ideal for species identification and sound event detection. This research presents an innovative approach to enhance the robustness of MFCC-based passive marine listening through adaptive noise reduction techniques. The proposed approach utilizes dynamic spectral subtraction to counter underwater noise, resulting in enhanced signal-to-noise ratios for desired sounds. This adaptive system adjusts to dynamic underwater noise, allowing it to concentrate on target sounds and suppress interference effectively. The experimentation further validates the effectiveness of the proposed approach, with results reaching 99% on the full dataset of 570 mammals and vessels, demonstrating the effectiveness of SVM and Random Forests in the classification of underwater audio.

Most studies on the association of in utero exposure to cigarette smoking and childhood overweight or obesity (OWO) were based on maternal self-reported smoking data and few were based on objective biomarkers. In this study, we evaluated the associations between self-reported and biomarkers of in utero exposure to cigarette smoking with risk of childhood OWO. We analyzed data from 2351 mother-child pairs in the Boston Birth Cohort, a US low-income minority cohort that enrolled children at birth and followed prospectively up to age 18 years. In utero smoking exposure was measured by maternal self-report and by maternal and cord plasma cotinine and hydroxycotinine metabolites. We assessed the individual and joint associations of each smoking exposure measure and maternal OWO with childhood OWO using multinomial logistic regressions. We used nested logistic regressions to investigate the childhood OWO prediction performance when adding maternal and cord plasma biomarkers as input covariates on top of self-reported data. Our results demonstrated that in utero cigarette smoking exposure defined by self-report and by maternal or cord metabolites were consistently associated with increased risk of long-term child OWO. Adding maternal and cord plasma biomarker information to self-reported data improved the prediction accuracy of long-term child OWO risk.

Plant Factory Transplanter (PFT) is a key component of the plant factory system. Its operation status directly affects the quality and survival rate of planted seedlings, which in turn affects the overall yield and economic efficiency. To monitor the operation status and transplanting quality of a transplanting machine in a timely manner, the primary task is to use a computerized and easy-to-use method to monitor the transplanting units. Inspired by the latest developments in augmented reality and robotics, a DT model-based and data-driven online monitoring method for plant factory transplanting equipment is proposed. First, a data-driven and virtual model approach is combined to construct a multi-domain digital twin of the transplanting equipment. Then, taking the vibration frequency domain signal above the transplanting manipulator and the image features of the transplanting seedling tray as input variables, the evaluation method and configuration method of the PFT digital twin system are proposed. Finally, the effect of the transplanter is evaluated, and the cycle can be repeated to optimize the transplanter to achieve optimal operation parameters. The results show that the digital twin model can effectively use the sensor data to identify the mechanical vibration characteristics and avoid affecting transplanting quality due to mechanical resonance. At a transplanting rate of 3000 plants/h, the transplanting efficiency can be maintained at a high level and the vibration signal of X, Y, Z-axis above the transplanting manipulator is relatively calm. In this case, Combined the optimal threshold method with the traditional Wiener algorithm, the identification rate of healthy potted seedlings can reach 94.3%. Through comprehensively using the optimal threshold method and 3D block matching filtering algorithm for image threshold segmentation and denoising, the recognition rate of healthy seedlings has reached over 96.10%. In addition, the developed digital twin can predict the operational efficiency and optimal timing of the detected transplanter, even if the environmental and sensor data are not included in the training. The proposed digital twin model can be used for damage detection and operational effectiveness assessment of other plant factory equipment structures.

To elucidate the function of the cold resistance regulatory gene FmNAC1 from Fraxinus mandshurica, this study identified the role that the overexpression of the FmNAC1 gene plays in tobacco growth and cold stress regulation. The cloned FmNAC1 gene from F. mandshurica is 891 bp in length and encodes 296 amino acids. Our subcellular localization analysis confirmed that FmNAC1 is primarily located in the nucleus and functions as a transcription factor. FmNAC1 is responsive to cold and NaCl stress, as well as to the induction of IAA, GA, and ABA hormone signals. To further elucidate its function in cold resistance, four transgenic tobacco lines of FmNAC1 overexpression（FmNAC1-OE）were generated through tissue culture after the agrobacterium-mediated transformation of wild-type (WT) tobacco. These FmNAC1-OE plants exhibited accelerated growth after transplantation. When exposed to low-temperature conditions at -5°C for 24 hours, the rates of wilting and yellowing of the FmNAC1-OE plants were significantly lower than those of the WT tobacco plants. Additionally, the membrane integrity, osmotic regulation, and reactive oxygen species (ROS)-scavenging abilities of the FmNAC1-OE tobacco lines were better than those of the WT plants, indicating the potential of the FmNAC1 gene to improve plant cold resistance. The gene expression results further revealed that the FmNAC1 transcription factor exhibits regulatory interactions with growth-related genes such as IAA and AUX1; cold resistance-related genes such as ICE, DREB, and CBF1; and genes involved in the clearance of reactive oxygen species (ROS), such as CAT and SOD. All of this evidence shows that the FmNAC1 transcription factor from F. mandshurica plays a key role in contributing to the enhancement of growth, cold resistance, and ROS clearance in transgenic tobacco plants.

Some peptide-based drugs including oxytocin, vasopressin, ziconotide, pramlintide, nesiritide, and octreotide, contain one intramolecular disulfide bonds. A novel and reusable monodispersed silica nanosphere-supported Pt(IV) complex (SiO2@TPEA@Pt(IV)) was synthesized via a four-step procedure and used for formation of intramolecular disulfide bonds in peptides. TEM and chemical mapping results for the Pt(II) intermediates and for SiO2@TPEA@Pt(IV) show that the silica nanospheres possess a monodisperse spherical structure and contain uniformly distributed Si, O, C, N, Cl, and Pt. The valence state of Pt on the silica nanospheres was characterized by XPS. The Pt(IV) loaded on SiO2@TPEA@Pt(IV) was 0.15 mmol/g, as determined by UV-vis spectrometry. Formation of intramolecular disulfides in six dithiol-containing peptides of variable lengths by use of SiO2@TPEA@Pt(IV) was investigated and the relative oxidation yields were determined by HPLC. In addition, peptide 1 (Ac-CPFC-NH2) was utilized to study the reusability of SiO2@TPEA@Pt(IV). No significant decrease in the relative oxidation yield was observed after ten reaction cycles. Moreover, the structure of SiO2@TPEA@Pt(IV) after being used ten cycles was determined to be similar to its initial one, demonstrating the cycling stability of the complex.

The field of mitochondrial genomics has advanced rapidly and revolutionized disciplines from molecular anthropology, population genetics, to medical/oncogenetics. However, mtDNA next-generation sequencing (NGS) analysis for matrilineal haplotyping and phylogeographic inference remains hindered by the lack of a consolidated, mitogenome database and efficient bioinformatics pipeline. To address this, we developed a customized human mitogenome database (hMITO DB) embedded in a CLC Genomics workflow for read mapping, variant analysis, haplotyping, and geo-mapping. The database was constructed from 4,286 mitogenomes. The macro-haplogroup (A to Z) distribution and representative phylogenetic tree were found consistent with published literature. The hMITO DB automated workflow was tested using mtDNA-NGS sequences derived from Pap smears and cervical cancer cell lines. The auto-generated read mapping, variants track, and table of haplotypes and geo-origins were completed in 15 min for 47 samples. The mtDNA workflow proved to be a rapid, efficient and accurate means of sequence analysis for translational mitogenomics.

The molecular clusters ((HO)3Si-O-Si(OH)3, and (HO)3Al-O-Si(OH)3 ) representative of aluminosilicate mineral surface were employed to study the dissolution of aluminosilicate in acidic condition via density functional theory with the M06-2X+G(d,p) methodology. The surface termination sites (Si and Al) were both tetra-coordinated and the terminal oxygen was protonated in acidic condition. In the dissolution reaction, the calculated barrier height of the six-membered ring transition state complex containing two water molecules was predicted to be lower than that of four-membered ring transition state complex containing one water molecule. In addition, the calculated barrier heights for Al-terminated sites were predicted to be lower than those for the Si-terminated sites, suggesting that breaking the Al-O bond is easier than Si-O bond in the aluminosilicate mineral surface; the barrier heights of the surface termination sites with protonated terminal oxygen were lower than those without protonated terminal oxygen. With the fracture of Si-O and Al-O bonds, the Si and Al release from the aluminosilicate. These results confirm the experimental conclusions that the acidic condition facilitates the release of Si and Al from the aluminosilicate, and the concentration of Al leaching from aluminosilicate is higher than Si.

“Anti-stripping Agents" or "adhesion promoters” can enhance the chemical affinity between as-phalt and aggregate by increasing their mutual attraction. Various forms of anti-stripping agents have been proposed to mitigate pavement stripping, and siloxane-based Zychotherm is one of them. Choosing the appropriate type and dose of anti-stripping additives is no doubt vital to the intended performance. Therefore, it is critically important to determine the dose of the additives used in the modification of asphalt binders. This research developed a feasible detection method that can closely measure the dose (0.05% and 0.1%) of siloxane-based anti-stripping liquid agents. Related test methods including heat combustion test, residue visualization, burning, and ignition were implemented. Heat combustion results showed that with the addition of Zychotherm anti-stripping additive, average heat combustion value decreased by 1.34% and 1.72% for 0.05% and 0.1% Zychotherm modified binder respectively. In the burning and ignition process, the modified binder leaves yellowish substances in the residue, which is an indication of the presence of Zy-chotherm. The weight of the yellowish residue relates more to the quantity of Zychotherm in as-phalt binder.

Chitosan is a copolymer of β-glucosamine and N-acetylglucosamine. Recent experiments showed that the degree and pattern of acetylation along the chitosan chain modulate the biological and physicochemical properties; however, the molecular mechanism is unknown. Here we apply the de novo all-atom molecular dynamics (MD) simulations to study chitosan’s self-assembly process at different degrees of acetylation and two different acetylation patterns. The simulations revealed that the 10-mer chitosan chains with 50% acetylation in either block or alternating patterns associate to form ordered nanofibrils comprised of mainly antiparallel chains in agreement with the fiber diffraction data of deacetylated chitosan. Surprisingly, regardless of the acetylation pattern, the same intermolecular hydrogen bonds mediate the fibril sheet formation while water-mediated interactions stabilize the sheet-sheet stacking. Moreover, the acetylated units are involved in forming the strong intermolecular hydrogen bonds (NH–O6 and O6H–O7), which offers an explanation for the experimental observation that increased acetylation lowers chitosan’s solubility. Taken together, the present study provides the atomic-level understanding the role of acetylation plays in modulating chitosan’s physiochemical properties, contributing to the rational design of chitosan-based materials with the ability to tune by its degree and pattern of acetylation. Additionally, we disseminate the improved molecular mechanics parameters that can be applied in MD studies to further understand chitosan-based materials.