In the recent decade, Building Information Modelling (BIM) has widely been adopted in the Architecture, Engineering and Construction (AEC) industry and completely upended the way we build. While BIM continues gain momentum in the industry, it has also attracted increasing attentions from researchers. However, most of the current study focuses on reviewing BIM for management, BIM for green building, BIM for infrastructure and BIM for Facilities Management (FM). There are few studies about Global BIM review and to discuss their complex inter-connections. In this study, we adopted a scientometric analysis method to review global BIM research from 2004-2019. A total of 1455 scholarly bibliographic records obtained from Web of Science Core Collection databased were established for the analysis. This study has identified the top productive and influential researchers, research institutes, regions/countries, subject categories and journals in the BIM field. In addition, 11 clusters of Global BIM research were also identified including construction project, green BIM, construction safety planning, automated IFC-based workflow and so on. Authors distinguished 11 clusters of global BIM research into 3 stages, namely formulating stage, accelerating stage and transforming stage. Furthermore, authors reviewed the BIM policy of Singapore and observed there is a co-production relationship between evolution of BIM policy and global BIM research. These findings provide valuable information for researchers, practitioners and policy makers by visualizing the current progress in the research field of BIM and highlighting future research needs.

A single-crystal of ytterbium-doped “mixed” yttrium-lutetium aluminium garnet with a stoichiometric composition of (Y0.601Lu0.233Yb0.166)3Al5O12 was grown by the Czochralski method and its structure, vibronic, spectroscopic and laser properties were studied. The stimulated-emission cross-section for Yb3+ ions was maximized to 2.53×10-20 cm2 at 1031 nm, the emission bandwidth is ~8 nm and the reabsorption-free luminescence lifetime of the 2F5/2 state is 1.063 ms. Pumped at 941 nm, the Yb-laser generated a maximum output power of 1.04 W at 1.03 and 1.05 μm with a high slope efficiency of 76.4% and a laser threshold of 76 mW. A continuous wavelength tuning over a range of 51.6 nm (1026.4 - 1078.0 nm) was also achieved. Power scaling is achieved using a 969 nm-diode pumped microchip cavity. A maximum output power of ~9 W is obtained at 1.05 μm with a slope efficiency of 76% and with an almost circular laser beam profile.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

In order to investigate the relationship between government policy, the service and design of rural crowdsourcing spaces, the self-efficacy of returning youth, and the innovation performance of businesses, this study focuses on gathering data by distributing questionnaires to returning youth in rural crowdsourcing spaces and developing a structural model. The results demonstrate how important government policies are in encouraging youth entrepreneurship in their local communities. It has the potential to enhance both the development of rural crowdsourcing spaces and the self-efficacy of young entrepreneurs, thereby enhancing the innovative capabilities of local entrepreneurial businesses. Therefore, in order to encourage economic development in rural areas, the government should improve pertinent support measures.

Hyperuricemia is mainly caused by the overproduction of uric acid (UA) catalyzed from xanthine by xanthine oxidase (XO) in abnormal purine metabolism in human body. There is an increasing demand for developing novel XO inhibitors of plant origins. The inhibition kinetics and type as well as actions of hesperetin against XO were investigated in vitro using multi-spectroscopic methods including UV-Vis absorption, Fourier transform infrared spectroscopy (FT-IR), fluorescence spectroscopy and molecular docking simulation. Results indicated that hesperetin reversibly inhibited XO in a competitive manner with an inhibition constant (Ki) value of (2.15 ± 0.05) × 10-6 mol/L. Hesperetin had a higher scavenging rate against O2- radical generated by the XO reaction system. The binding of hesperetin to the active site of XO altered the protein’s secondary structure as demonstrated by FT-IR and fluorescence spectra. Molecular docking study revealed that hesperetin had highly affinity to XO and the bonding of hesperetin to the molybdopterin (Mo-pt) active center inhibited not only substrate entry, but also prevented oxygen binding to flavin adenine dinucleotide (another active center in XO). Additionally, hydrophobic interactions and hydrogen bonds contributed to the stabilization of the hesperetin-XO complex. The results suggested that hesperetin be a promising natural XO inhibitor to alleviate hyperuricemia and gout.

This work is devoted to physical vapor deposition synthesis, and characterisation of bismuth and lutetium-substituted ferrite-garnet thin-film materials for magneto-optic (MO) applications. The properties of garnet thin films sputtered using a target of nominal composition type Bi_0.9Lu_1.85Y_0.25Fe_4.0Ga₁O₁₂ are studied. By measuring the optical transmission spectra at room temperature, the optical constants and the accurate film thicknesses can be evaluated using Swanepoel’s envelope method. The refractive index data are found to be matching very closely to these derived from Cauchy’s dispersion formula for the entire spectral range between 300-2500 nm. The optical absorption coefficient and the extinction coefficient data are studied for both the as-deposited and annealed garnet thin-film samples. A new approach is applied for accurately deriving the optical constants data simultaneously with the physical layer thickness, using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method. MO properties, such as specific Faraday rotation, MO figure of merit and MO swing factor are also investigated for several annealed garnet-phase films.

Coptisine (Cop) exerts a neuroprotective effect in central nervous system disease, particularly ischemic stroke. However, its protective mechanism is still unclear. This study aimed to investigate the protective effect of Cop on cerebral ischemia-reperfusion (IR) rats with a middle cerebral artery occlusion model by integrating a gas chromatography-mass spectrometry (GC-MS) based metabolomics approach with biochemical assessment. Our results showed that Cop could improve neurobehavioral function and decrease the ischemia size in IR rats. In addition, Cop was found to decrease inflammatory mediators (e.g., prostaglandin D2 (PGD2) and tumor necrosis factor-α (TNF-α) and attenuate oxidative stress response (e.g., increase the superoxide dismutase (SOD) expression and decrease 8-iso-PGF2α level). Furthermore, GC-MS based cerebrospinal fluid (CSF) metabolomics analysis indicated that Cop influenced the level of glycine, 2,3,4-trihydroxybutyric acid, oleic acid, glycerol, and ribose during IR injury. Cop exhibited a good neuroprotective effect against cerebral IR injury and metabolic alterations which might be mediated through its antioxidant and anti-inflammatory property.

JIS SUJ2 is most widely used in bearing steels. The advantages are good hardenability, excellent fatigue, wear resistance and comprehensive mechanical properties. For wear resistance and fatigue resistance of the steel are getting more and more attention, the residual stress state and its distribution on the surface of the heat affect zone are critical factors affecting the fatigue life and wear resistance of the parts. In this study, using the SUJ2 as the material to talk about the surface residual stress and retained austenite distribution. Doing the quenching and tempering treatment to obtain different microstructures, using the induction method to re-quench the case region. After the heat treatment, measuring the residual stress and retained austenite volume on the surface by X-ray diffraction, observing the microstructure and comparing the hardness. The results show that the microstructure after heat treatment contains unsolidified carbides, tempered martensite and retained austenite. The residual stress on the surface is the tensile state. In the re-hardened area after induction quenching, the residual stress is all compressive, and the values are more than -800 MPa. In conclusion, in the same output power condition can be observed that the microstructure of the specimens before induction hardening has a significant impact on the effective case depth. The surface residual stress has changed from a tensile to a compressive state. In the re-hardened area, the maximum of the residual compressive stress increased with the austenitized temperature increase.

Soarinho Alkaline Intrusion, southeastern Brazil, makes part of the Serra do Mar Igneous Province, and it is composed of alkali feldspar syenite, alkali feldspar trachyte, quartz syenite, and mon-zonite. Geochemical and geochronological analysis of the Soarinho were compared with data from its neighbors Rio Bonito and Tanguá. Zircon U-Pb Laser Ablation ages show that Soarinho is youngest than Rio Bonito and Tanguá. Ages obtained from the monzonite (60 ± 2 Ma), alkali feldspar syenite (58 ± 2 Ma), and quartz syenite (58 ± 2 Ma) are indistinguishable within error. Petrographic and geochemical data show a clear contrast among Soarinho, Rio Bonito, Tanguá, and Lu-Hf isotopic data for the three alkaline intrusions (all negative), point to some similarities in their sources. The data suggest an enriched mantle source for Soarinho; however, an older con-tinental crust contribution cannot be discarded.

This article investigates the information matching efficiency of the sponsored auction mechanism of search engine platform by implementing consumer purchase strategy. Then we examine the incentive mechanism for sellers to report product quality truthfully under information asymmetry and the reason how product quality signal could improve information matching efficiency of the sponsored auction mechanism. Using the data collected from Baidu search engine, we empirically test the theoretical research results. Our main research finding: under information asymmetry and without product quality signal mechanism, the equilibrium of bidding rank cannot match the consumer purchase strategy at all, causing the consumer welfare to suffer double losses due to the adverse selection of sellers. In the contrast, the search engine could improve partially the information matching efficiency of the sponsored search auction mechanism by identifying the product quality signal brought by the sellers with the highest product quality. However, the search engine has no incentive to design product quality signal for sellers.

With the development of Internet technology, teachers are constantly seeking innovative teaching methods to match the potential of enhanced technology. Although many studies have been performed before , they aren’t enough in this field. The purpose of this paper is to explore innovative teaching designs and examine the impact of Internet-assisted English teaching of reading based on constructivism. The case is carried out in NO.9 middle school of Bengbu, a underdeveloped area of China, most of students aren’t interested in learning English .We compared Internet-assisted with traditional textbook literature methods to improve the reading proficiency of students, using a questionnaire survey,pre-test and post-tests comparisons. The result showed Internet-assisted English reading teaching is better than textbook. It can arouse students' interest and motivation,reading proficiency and exam result of students have been improved significantly, created a positive learning situation.

Using the Super-SBM method, this study calculates the carbon emission efficiency (CEE) of 30 provinces in mainland China from 2011 to 2019. Then, using the systematic GMM model, spatial Durbin model, and mediating effect model, it examines the direct effect, spatial effect, and influence mechanism of the digital economy (DE) on CEE. It was found that (1) the DE significantly promoted regional CEE, but had a negative effect on CEE in provinces with high economic correlation; (2) mechanism studies showed that the DE improved CEE by reducing energy intensity, promoting industrial upgrading and green technology innovation; (3) regional heterogeneity analysis found that the DE significantly improved CEE in eastern provinces, but not in central and western provinces. DE improves CEE in provinces with high level of economic development, but decreases CEE in provinces with low level of economic development.This paper provides some empirical and theoretical references for the development of DE to improve CEE.

The broad emission bump in the electromagnetic spectra observed following the detection of gravitational waves created during the kilonova event of merger of two neutron stars in August 2017, GW170817, has been linked to the heavy elements of lanthanides (Z=57-71), and a new understanding of creation of heavy elements in the r-process. The initial spectral emission bump has a wavelength range of 3000 - 7000 \AA, thus covering the region of ultraviolet (UV) to optical (O) wavelengths, and is similar to those seen for lanthanides. Most lanthanides have large number of closely lying energy levels which introduce extensive sets of radiative transitions which often form broad region of lines of significant strength. The current study explores these broad features through photoabsorption spectroscopy of 25 lanthanides ions, Ho I-III, Er I-IV, Tm I-V, Yb I-VI and Lu I-VII. With excitations only to a few orbitals up beyond the ground configurations, we find most of these ions cover large number of bound levels with open $4f$ orbital and produce tens to about hundred thousands lines that may form one or multiple broad features in X-ray to UV, O, and infrared (IR) regions. Spectrum of each of 25 ions is presented indicating presence, shape and wavelength region of the features. Accuracy of atomic data to interpret the merger spectra has been a outstanding problem. The present study aims at providing improved atomic data for energies and transition parameters obtained using relativistic Breit-Pauli approximation implemented in the atomic structure code SUPERSTRUCTURE. The present data have been benchmarked with available experimental data for energies and transition parameters. The study finds that number of ions under the present study are possible contributors of the emission bump of GW170817. All atomic data will be made available online at NORAD-Atomic-Data database.

There are some controversies about 2G bioethanol and it is in need of a reliable test data in order to make a further analysis and proof. In collecting basic data from three classes of typical raw materials, such as wheat, maize stalk juice, and straw, it was found that 4.32 tons straw or 3.358 tons wheat is needed to produce 1-ton bioethanol. Using the coefficient of variation calculation and analysis method, it is able to obtain the C.V. value of straw fermentation efficiency 0.08932<0.15, indicating the fermentation technology and process of 2G bioethanol is already quite mature and reliable, without risk, and also with a raw material cost advantage. There is a problem in that the C.V. value of straw volume is 1.2648>0.95, indicating 2G bioethanol is in an extremely high-risk area. Using the straw volume calculation method, building and its costs – capital expenditure of 2G bioethanol plant is approximately seven times that of a wheat ethanol plant. This should be some of the important reasons why it is noncompetitive, extremely high price, and requiring government subsidies. Straw volume data study has caused the 2G bioethanol plant to require more cement, steel, equipment, and other materials. Thus, there are ample reasons to question the CO2 emissions and its carbon footprint of 2G bioethanol plant. Actually, the volume is not the only existing problem, it is necessary to re-evaluate and discuss the definition of 2G bioethanol and its future.

We present the generation and nonlinear frequency conversion of nanosecond cylindrical vector beams (CVBs) in two-mode fiber (TMF). Based on the polarized dependence vector mode coupling characteristic and the precise wavelength tunability of an acoustically-induced fiber grating (AIFG), the nanosecond cylindrical vector beams (CVBs, 1064 nm, 10 ns) is directly generated in a TMF with convenient switching characteristics between the radial and azimuthal vector beams. Furthermore, the stimulated Raman scattering (SRS) is produced based on the transmission of the nanosecond CVBs in the 100-meters long TMF, and the spatial intensity and polarization distributions characteristics the 1st-order Stokes shifted component is consistent with the nanosecond CVBs pump pulse. This work provides a method for achieving wavelength conversion of the CVBs in optical fiber.

Machine learning methods have been a standard approach to select features that are associated with an outcome and build a prediction model when the number of candidate features is large. LASSO has been one of the most popular approaches to this end. LASSO approach selects features with large regression estimates, rather than based on statistical significance, associating the outcome, by imposing L1-norm penalty to overcome the high dimensionality of the candidate features. As a result, LASSO may select insignificant features while possibly missing significant ones. Furthermore, from our experience, LASSO has been found to select too many features. By selecting features that are not associated with the outcome, we may have to spend more cost to collect and manage them in the future use of a fitted prediction model. Using the combination of L1- and L2-norm penalties, elastic net (EN) tends to select more features than LASSO. The overly selected features that are not associated with the outcome act like white noise, so that the fitted prediction model loses the prediction accuracy. In this paper, we propose to use the standard regression methods (without any penalizing approach) with stepwise variable selection procedure to overcome these issues. Unlike LASSO and EN, this method selects features based on statistical significance. Through extensive simulations, we show that this maximum likelihood estimation based method selects very small number of features while maintaining a high prediction power, while LASSO and EN make a large number of false selections to result in loss of prediction accuracy. Contrary to LASSO and EN, the regression methods combined with a stepwise variable selection method is a standard statistical method, so that any biostatistician can use it to analyze high dimensional data even without advanced bioinformatics knowledge.

While considering the sensitivity over the parameter optimization, it is essential to determine which parameters have the most significant implications on model performance. This study focuses on the baseflow recession constant as one of the independent basin parameters to forecast low flows, perform hydrograph analysis, and calibrate rainfall-runoff models for significant improvement. Prior studies examined that the optimization of data adjustment parameters can improve the hydrological model performance and determine the minimum acceptable data length for data scarce regions using the Xinanjaing model. However, it is essential to pay special attention to the sensitivity of the recession constant, which can also impact the model performance during the data scarcity. Therefore, this study extends the research to comprehend the recession constant sensitivity over data adjustment parameters in the shorter datasets leading to more reliable parameter estimation. In terms of that, this study explores how recession constant affects hydrological parameter estimation on annual scale while keeping data adjustment parameters constant in continuous hydrological modeling, employing the Xinanjiang (XAJ) model as a case study. This study considered two approaches of recession constant (cg); (i) assessing the relationship between cg and the data adjustment parameter (Cep), for the 28-year datasets, (ii) investigating the significant impacts of the sensitivity of cg over Cep in shorter datasets which can affect the estimation of the acceptable minimum data length in the data scarce basins. The study underscores the importance of the recession constant sensitivity for reliable continuous hydrological model predictions, especially in data-scared areas. The study’s outcomes enhance the understanding of the importance of parameter sensitivity and its relationship in conceptual hydrological modeling during the data limitations.

The most recent National Research Council Nutrient Requirements for Sheep and Goats was published in 2007, one of the most consequential nutrient requirement recommendations for sheep and goats in the world. It is pertinent to continue the refinement and discussion of nutrient utilization and requirements for the purposes of enhancing the efficiency of production systems, maximizing resource economy, and minimizing the carbon footprint, among others. Progress has been made in the estimation of energy and protein requirements in sheep and goats, mainly utilizing empirical feeding experimentation, comparative slaughter technique and minimum endogenous loss method. In sheep, newer estimates of energy and protein requirements for maintenance and growth and partial efficiencies had been reported since 2007. There were suggestions that energy and protein requirements could have been affected by breed, wool growth, gender and size; with these reported values being similar or lower than the recommended values in international feeding systems such as NRC, ARC, INRA and AFRC. In goats, energy and protein requirements for growing goats were reported to be either higher or lower than the established recommendations, depending upon meat or dairy breeds. Effect of gender on energy requirement appeared to be related to the stage of growth or degree of maturity. Newer data also suggested that the guidelines of the major feeding systems for the entire growth phase may not be adequate for non-pregnant and non-lactating pubertal females. In multiparous pregnant goats, energy and protein requirements for maintenance did not appear to be affected by days of pregnancy, but efficiencies of metabolizable energy and metabolizable protein utilization for pregnancy were. There were suggestions that that metabolizable protein synthesis in the rumen can be predicted from energy intake using combined equations that encompass both sheep and goats, but more data on goats were called for to account for specific differences in nutrition. In addition to sulfur, there has been progress made on the estimation of maintenance and growth requirements of calcium, phosphorus, potassium and magnesium in goats, with suggestions on the consideration of gender and breed differences. Species, level of Intake, genotype, mature size, age, gender, body composition, use of tissue energy, activity, season, and acclimatization continue to be important considerations for the estimation of nutrient requirements in sheep and goats, with emerging factors such as climate change, heat stress, parasitism and secondary plant compounds. Model equations and partial efficiencies used by NRC to predict energy and protein requirements for maintenance, growth, lactation, and fiber have been highlighted and discussed for the purpose of a more focus discussion and refinement for the future. Potential and limitation of both traditional and emerging methodologies in determining the nutrient requirements in sheep and goats were discussed. To justify the research investment, emerging methodologies such as nutrigenomics will have to be linked more directly to the improvement of production efficiency via more precise prediction of nutrient requirement.

The sand-dust horizontal flux is an important parameter for the study on aeolian sand transport, as well as an important foundation. In this study, a field experiment was developed to measure the data of aeolian transport and microclimate during different dust events with an auto sand sampler, a piezoelectric saltation sensor (H11-Sensit) and a 10 m high meteorological tower in Ta Zhong, the hinterland of the Taklimakan Desert from July to August in 2010. Then, the sampling efficiency of auto sand sampler and horizontal dust flux of near surface were analyzed based on observed data. The results were as follows: sand collector skip turnover increased with the increase of the intensity of dust weather frequency increases, the power function relationship y=2.115 x0.9841, R2 = 0.9206, flip frequency per minute increased from 0.2794 times to 1.3041 times, change is obvious; With the strength of the weather, time to flip the average sediment is shrinking. Sandstorm weather, skip to flip a volume of 3.7160 g, grade I flying sand weather flip a volume of 4.0275 g, the amount of class II flying sand weather turns over a 5. 0035g.The horizontal dust flux of different dust events that calculated with the equation Q=256M; the maximum of one dust event was about 190.335 kg, and the minimum was 1.2 kg. Overall, the sand transportation rate increased with wind speed. However, the changes of sand transportation rate did not quite fit in with wind speed during some dust events, and in this case the corresponding surface temperature was significantly higher. The experimental data obtained can provide theoretical basis for regional sand control and enacting effective engineering measures.

Liquid-liquid phase separation (LLPS) of proteins has been found ubiquitously in eukaryotic cells, critical in the controlling of many biological processes through forming a temporary condensed phase with different bimolecular components. TDP-43 is recruited to stress granules in cells and is the main component of TDP-43 granules and proteinaceous amyloid inclusions in patients with amyotrophic lateral sclerosis (ALS). TDP-43 low complexity domain (LCD) is able to demix in solution forming the protein condensed droplets. The molecular interactions regulating its LLPS were investigated at the protein fusion equilibrium stage, where the droplets stopped growing. We found the molecules in the droplet were still liquid-like but with enhanced intermolecular helix-helix interaction in the LCD. The protein would start to aggregate after about 200 minutes of lag time and aggregate slower than at the condition when the protein does not phase separate or the molecules have a reduced intermolecular helical interaction. A structural transition intermediate towards protein aggregation was also discovered involving a decrease of the intermolecular helix-helix interaction and a reduction in the helicity. Therefore, LLPS and the intermolecular helical interaction could help maintain the stability of TDP-43 LCD.

Wound healing is a complex, dynamic process involving the coordinated interaction of diverse cell types, growth factors, cytokines, and extracellular matrix components. Despite emerging evidence highlighting their importance, dermal sheath cells remain a largely overlooked aspect of wound healing research. This review explores the multifunctional roles of dermal sheath cells in various phases of wound healing, including modulating inflammation, aiding in proliferation, and contributing to extracellular matrix remodeling. Special attention is devoted to the paracrine effects of dermal sheath cells and their role in fibrosis, highlighting their potential in improving healing outcomes, especially in differentiating between hairy and non-hairy skin sites. By drawing connections between dermal sheath cells activity and wound healing outcomes, this work proposes new insights into the mechanisms of tissue regeneration and repair, marking a step forward in our understanding of wound healing processes.

We study the Gaudin models with gl(1|1) symmetry that are twisted by a diagonal matrix and defined on tensor products of polynomial evaluation gl(1|1)[t]-modules, extending all the results of to the twisted case. Namely, we give an explicit description of the algebra of Hamiltonians (Gaudin Hamiltonians) acting on tensor products of polynomial evaluation gl(1|1)[t]-modules and show that there exists a bijection between common eigenvectors (up to proportionality) of the algebra of Hamiltonians and monic divisors of an explicit polynomial written in terms of the highest weights and evaluation parameters. In particular, our result implies that each common eigenspace of the algebra of Hamiltonians has dimension one. We also give dimensions of the generalized eigenspaces.

Background: Previous in vitro and in vivo studies have demonstrated that storage of cooked rice at 4 °C for 24 h and reheating to 65 °C significantly reduced starch digestibility and postprandial glycaemic responses. Moreover, the effect was greater for parboiled rice compared to other rice varieties commonly consumed in New Zealand. This study aimed to evaluate consumer preferences of related sensory attributes and consumer acceptability of several rice varieties freshly cooked or reheated. Method: Sixty-four consumers volunteered and recorded on Visual Analoge Scales their preference and acceptability of freshly prepared or cold-stored and reheated medium grain white, medium grain brown and parboiled rice. Results: All six rice samples were accepted by participants (average 54%). Reheated parboiled rice and reheated medium grain brown rice were both accepted by participants as a preferred staple meal compared to other rice samples. Among all rice samples, the sweetness and the flavour of freshly cooked warm medium-grain white rice were less preferred (scored 42.1% and 45.0% respectively) compared with other samples (P = 0.05). Participants who prepared and consumed brown rice at home regularly (more than 10 times per month), preferred the reheated brown rice (73.8% (67.4, 80.2)) and reheated parboiled rice (74.3% (67.9, 80.7)) (P < 0.001). Conclusions: It is suggested that reheated parboiled rice, with the lowest starch digestibility and glycaemic impact (both in vitro glucose release and in vivo glucose response) could be accepted as a healthier alternative for the daily staple meal.

Hydrogen is considered as an ideal substitute to the traditional fossil fuels because of its widespread sources, high calorific value of combustion, and zero carbon emissions. The electrocatalytic water-splitting to produce hydrogen is also deemed to be the best approach, however, it is a challenge to make high-efficient and low-cost electrocatalysts. Single-atom catalysts (SACs) are considered the most promising candidate to replace the traditional noble-metal catalysts. Compared with SACs, the dual-atom catalysts (DACs) are of greater attraction including higher metal loading, more versatile active sites, and excellent catalytic activity. In the review, several general synthetic strategies and structural characterization methods of DACs are introduced, and the mechanisms of hydrogen evolution reaction (HER) and oxygen evolution reactions (OER) are discussed. The authors hope that the review has given some insights and inspiration to the researchers about DACs in electrocatalytic water-splitting.

Crystalline silicon nanomembrane (Si NM) is promising in wearable and implantable bioelectronics due to its electrical and mechanical performances. However, the current explorations are not enough to firmly bridge ultrathin encapsulation strategies with high performance crystalline Si NM based transistors. In this work, we utilized Al2O3/alucone as the ultrathin encapsulation strategies aim to thoroughly investigate the effect of gate dielectric surface area on the electrical performance of crystalline Si NM based metal-oxide-semiconductor capacitors (MOSCAPs). The comparative analysis was implemented on the three types of diameters (Ø) MOSCAPs with and without Al2O3/alucone encapsulation under planar and concave/convex bending conditions. Benefited from the Al2O3/alucone ultrathin encapsulations, the stability of gate leakage current density, and interfacial characteristics were maintained and improved under mechanical bending deformations for MOSCAPs with predefined Ø of 160, 240, and 320 μm compared to the bare MOSCAPs. Combined with the Ø-related mechanical analysis on the maximum strain in the critical layers and the practical measurements, the encapsulated MOSCAPs with Ø 160 μm showed the most stable electro-mechanical performances. The variations for encapsulated MOSCAPs with three types of Ø emerged in the oxide layer and the interface at dielectric/Si NM that were carefully evaluated according to the bending deformations. These findings are significant for leveraging the practical applications in the ultrathin encapsulation strategies for reliable operations of crystalline Si NM based integrated circuits (ICs).

Nonnegative matrix factorization (NMF) has been shown to be a strong data representation technique, with applications in text mining, pattern recognition, image processing, clustering and other fields. In this paper, we propose a hypergraph regularized Lp smooth nonnegative matrix factorization (HGSNMF), by incorporating hypergraph regularization and Lp smoothing constraint terms into the standard NMF. The hypergraph regularization term can capture the intrinsic geometry structure of the high dimension space data more comprehensively than simple graph, the Lp smoothing constraint may yield a smooth and more accurate solution to the optimization problem. The updating rules are given using multiplicative update techniques, and the convergence of HGSNMF is theoretically investigated. The experimental results on four different data sets show that the proposed method has better clustering effect than the related state-of-the-art methods in the vast majority of cases.

Urban scene point cloud pose significant challenges for registration due to its large data volume, similar scenarios and dynamic objects. In this paper, we propose PCRMLP, a model for urban scene point cloud registration that achieves comparable registration performance to prior learning-based methods. Compared to previous works which focus on extracting features and estimating correspondence, the model estimates the transformation implicitly from concrete instances. An instance-level urban scene representation method is introduced to extract instance descriptors via semantic segmentation and DBSCAN, which enable the model to obtain robust instance features, filter dynamic objects and estimate transformation in a more logical manner. Then a lightweight network consisting of MLPs is employed to obtain transformation in an encoder-decoder manner. We validate the approach on KITTI dataset. Experimental results demonstrate that PCRMLP can obtain a satisfactory coarse transformation from instance descriptors just in 0.0028s. With a subsequent ICP refinement module, the proposed method achieves higher registration accuracy and computational efficiency than prior learning-based works.

A novel starch stabilized Mg/Al LDHs material (S-LDH) was prepared in a facile approach and its fluoride ion removal performance was developed. Characterization of S-LDH was employed by using XRD, FTIR and particle size distribution. The adsorption property was studied through the assessment of adsorption isotherms, kinetic models, thermal dynamics and pH influence. The result shows that a low loading of starch of 10 mg onto LDH could obviously improve fluoride removal rate. The S-LDH had 3 times higher adsorption capacity to fluoride than that of Mg/Al LDH to fluoride. The particle size was smaller and the particle size distribution was narrower for S-LDH than that for Mg/Al LDH. Langmuir adsorption isotherm model and pseudo-second-order kinetic model fitted well with the experimental data. In thermodynamic parameters, the enthalpy (△H0) value was 35.63 kJ mol-1 and the entropy (△S0) value was 0.0806 kJ mol-1K-1. The values of △G0 were negative, implying the adsorption process is spontaneous. S-LDH reveals stable adsorption property in a wide pH range from 3 to 9. The mechanism for fluoride adsorption on S-LDH included surface adsorption and interaction ion exchange.

The spread of 2019 novel coronavirus disease (COVID-19) throughout the world has been a severe challenge for public health. The human angiotensin-converting enzyme 2 (ACE2) has a remarkably high affinity binding to severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). By the search for network database and re-analysis of pubic data, we found the level of ACE2 expression in adipose tissue was higher than that in lung tissue, which indicated the adipose tissue might be vulnerable to SARS-CoV-2 as well; the levels of ACE2 expressed by adipocytes and adipose progenitor cells were similar between non-obese individuals and obese individuals, but obese individuals have more adiposes so as to increase the number of ACE2-expressing cells; the expression of ACE2 in tumor tissues posed by five different types of cancers increased significantly compared with that in adjacent tissues. Thus, we suggest that more attentions might be given to obese individuals and the five types of cancer patients during the outbreak of COVID-19.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

The quality of digital elevation models (DEMs) is inevitably affected by the limitations of the imaging modes and the generation methods. One effective way to solve this problem is to merge the available datasets through data fusion. In this paper, a fusion-based global DEM dataset (82°S-82°N) is introduced, which we refer to as GSDEM-30. This is a 30-m DEM mainly reconstructed from the unfilled SRTM1, AW3D30, and ASTER GDEM v2 datasets combining the multi-source and multi-scale fusion techniques. A comprehensive evaluation of the GSDEM-30 data, as well as the 30-m ASTER GDEM v2 and AW3D30 DEM, was presented. Global ICESat GLAS data and the local National Elevation Dataset (NED) were used as the reference for the vertical accuracy validation, while GlobeLand30 was introduced for the landscape analysis. Furthermore, we employed the maximum slope approach to detect the potential artefacts in the DEMs. The results show that the GDEM data are seriously affected by noise and artefacts. With the advantage of the multiple datasets and the refined post-processing, the GSDEM-30 are contaminated with fewer anomalies than both ASTER GDEM and AW3D30. The fusion techniques used can also be applied to the reconstruction of other fused DEM datasets.

Understanding how industrial agglomeration affects agricultural green production efficiency is essential for green agricultural development. This study uses the super-efficient EBM-GML to measure and analyze the spatial and temporal evolution characteristics and core sources of dynamics of agricultural green production efficiency in China by using panel data from 30 Chinese provinces from 2006 to 2020. It also empirically investigates the relationships between industrial agglomeration, land transfer, and agricultural production efficiency. By using fixed, intermediary, and threshold effects models, the internal links between the industrial agglomeration, land transfer, and agricultural green production efficiency are examined. The findings indicate that the green production efficiency of Chinese agriculture exhibits the regional characteristics of being “high in the west and low in the east, high in the south and low in the north” in terms of space; in terms of time series, the overall trend is that of growing, with an average annual growth rate of 11.45%, and the growth primarily depends on the “single-track drive” of green technological progress. By promoting land transfer, industrial agglomeration can increase the agricultural green production efficiency and decomposition index. Land transfer has a double-threshold effect on the influence of industrial agglomeration on agricultural green production efficiency. As a result, this study suggests adhering to the idea of synergistic development, promoting agricultural green development, strengthening the development of industrial agglomerations, promoting the quality and efficiency of industry, improving land-transfer mechanisms, and placing a focus on resource efficiency improvements, as well as other policy recommendations.

Background: Globally, hot cooked refined rice is consumed in large quantities and is a major contributor to dietary glycaemic load. This study aimed to compare the glycaemic potency of hot and cold stored parboiled rice to widely available medium grain white rice. Method: Twenty-eight healthy volunteers participated in a three treatment experiment where postprandial blood glucose was measured over 120 minutes after consumption of 140g of rice. Three rice samples were freshly cooked medium-grain white rice, freshly cooked parboiled rice, and parboiled rice stored overnight at 4 ºC. All rice was served warm at 65 ºC. Chewing time was recorded. Results: The 24-hours cold-stored and reheated parboiled rice resulted in a 42% and 12% lower blood glucose concentration trajectory than freshly cooked medium-grain white rice and freshly cooked parboiled rice. Chewing time for 10g cold stored parboiled rice was 6 seconds (25%) longer and was considered more palatable, visually appealing and better tasting than freshly cooked medium grain (all P<0.05). Conclusions:. For regular consumers of rice reheating cooked rice after cold storage would lower the dietary glycaemic load and long term may reduce risk for type 2 and gestational diabetes. More trials are needed to identify the significance.

Background: The major histocompatibility complex (MHC) plays a key role in the adaptive immune response to pathogens due to its extraordinary polymorphism. However, the spatial patterns of MHC variation in the striped hamster remain unclear, particularly regarding the relative contribution of balancing selection in shaping MHC population and diversity compared to neutral forces. Methods: In this study, we investigated the immunogenic variation of the striped hamster in four wild populations in Inner Mongolia, which experience heterogeneous parasitic stress. Our goal was to identify local adaptation by comparing the genetic structure at MHC with that at seven microsatellite loci, taking into account neutral processes. Results: We observed significant variation in parasite pressure among sites, with parasite burden showing a correlation with temperature and precipitation. Molecular analysis revealed a similar co-structure between MHC and microsatellite loci. We observed lower genetic differentiation at MHC loci compared to microsatellite loci, and no correlation was found between the two. Conclusions: Overall, these results suggest a complex interplay between neutral evolutionary forces and balancing selection in shaping the spatial patterns of MHC variation. Local adaptation was not detected at a small scale but may be applicable at a larger scale.

Due to the major impact of climate change on the world's environment, political and economic systems, climate change mitigation has become a pressing priority for the international community and requires rapid action from the whole society. With the continuous advancement of artificial intelligence research, the integration of AI and other technologies makes it more and more used in the whole society. It has become a promising and innovative avenue in the field of climate change mitigation. This paper comprehensively considers the key role of AI technology in the field of climate change mitigation, such as climate modeling, the optimization of renewable energy systems, the development of intelligent solutions for sustainable practices and CSS technology, and affirms its future prospects. It also describes the challenges of AI in the field of climate change mitigation. As researchers, policymakers, and industries collaborate to refine AI methodologies and integrate them into practical applications, a concerted effort is required to establish ethical guidelines, transparency standards, and inclusive governance frameworks.

We present a class of efficient parametric closure models for 1D stochastic Burgers equations. Casting it as statistical learning of the flow map, we derive the parametric form by representing the unresolved high wavenumber Fourier modes as functionals of the resolved variables’ trajectory. The reduced models are nonlinear autoregression (NAR) time series models, with coefficients estimated from data by least squares. The NAR models can accurately reproduce the energy spectrum, the invariant densities, and the autocorrelations. Taking advantage of the simplicity of the NAR models, we investigate maximal and optimal space-time reduction. Reduction in space dimension is unlimited, and NAR models with two Fourier modes can perform well. The NAR model’s stability limits time reduction, with a maximal time step smaller than that of the K-mode Galerkin system. We report a potential criterion for optimal space-time reduction: the NAR models achieve minimal relative error in the energy spectrum at the time step where the K-mode Galerkin system’s mean CFL number agrees with the full model’s.

Due to the periodic movement of the piston in the reciprocating pump, the fluid will cause pressure pulsation, and the vibration of the pipeline will lead to instrument distortion, pipe failure and equipment damage. Therefore, it is necessary to study the vibration phenomena of the reciprocating pump pipeline based on the pressure pulsation theory. This paper starts from the reciprocating pump pipe pressure pulsation caused by fluid, pressure pulsation in the pipeline and the excited force is calculated under the action of the reciprocating pump. Then, the numerical simulation model is established based on the pipe beam model, and the rationality of the numerical simulation method is verified by the indoor experiment. Finally, a case study is taken as an example to analyze the vibration law of the pipeline system, and proposed the stress reduction and vibration reduction measures. The main conclusions are drawn from the analysis: (1) Excited force is produced in the bend or tee joint, and it can also influence the straight pipe in different levels; (2) In this pipeline system, the pump discharge pipe has a larger vibration amplitude and lower natural frequency; (3) The vibration amplitude increases with the pipe thermal stress, and when the oil temperature is higher than 85°C, it had a greater influence on the vertical vibration amplitude of the pipe.

Abstract: Bacillus subtilis fmb60, which has broad-spectrum antimicrobial activities was isolated from plant straw compost. A hybrid NRPS/PKS cluster was screened from the genome. Sixteen secondary metabolites produced by the gene cluster were isolated and identified using LC-HRMS and NMR. Three lipoamides D–F (1-3) and two amicoumacin derivatives, amicoumacins D, E (4, 5), were identified, and are reported here for the first time. Lipoamides D–F exhibited strong antibacterial activities against harmful foodborne bacteria, with the MIC ranging from 6.25 to 25 µg/mL. Amicoumacin E scavenged 38.8% of ABTS+ radicals at 1 mg/mL. Direct cloning and heterologous expression of the NRPS/PKS and ace gene cluster identified its importance for the biosynthesis of amicoumacins. This study demonstrated that there is a high potential for biocontrol utilization of B. subtilis fmb60, and genome mining for clusters of secondary metabolites of B. subtilis fmb60 has revealed a greater biosynthetic potential for the production of novel natural products than previously anticipated.

Rapid urbanization has led to many ecological problems such as landscape fragmentation, decreased landscape connectivity, and decreased biodiversity. Building an ecological security pattern is an important way to ensure ecological security and maintain sustainable urban development. Harbin is an important large-scale city in northeastern China, and the urban central district of Harbin is used as the study area. Ecological sensitivity assessment, MSPA, gravity model, landscape connectivity assessment and MCR model were used to extract ecological source areas, ecological corridors and ecological nodes in the study area to construct and optimize the ecological security pattern. Research shows that: A total of 23 ecological source areas were identified, mainly located along the Songhua River in the central part of the study area and in the mountain forest areas within the A-cheng District in the southeastern part of the study area. 48 ecological corridors were extracted, mainly in Daowai District, A-cheng District and the eastern part of Xiangfang District. There are 8 important ecological corridors and 10 important connecting corridors. 61 ecological nodes of the first level and 65 ecological nodes of the second level were extracted. High, higher, medium, lower and low security areas were classified based on the minimum cumulative resistance surface, with the highest proportion of high ecological security areas accounting for 45.75% of the study area. 65 ecological breakpoints were extracted and restoration measures were proposed. Finally, The structure of the ecological security pattern optimization of "two axes, two belts and four areas" is proposed, and corresponding ecological management measures are put forward. The experimental system of this study can provide new ideas for the construction of ecological security patterns in other regions and provide scientific support for the ecological sustainable development of similar urban areas.

With the rapid and continuous advancement and deployment of advanced energy storage de-vices, there has been significant interest in aqueous capacitors that possess non-flammable properties and high safety features. Consequently, extensive research efforts have focused on investigating zinc anodes and low-cost carbonaceous cathode materials. Despite these efforts, the development of high-performance zinc-ion capacitors (ZICs) still faces challenges such as limited cycling stability and low energy densities. In this study, we present a novel approach to address these challenges. We demonstrate the utilization of a three-dimensionally (3D) grown conductive porous carbon framework cathode coupled with zinc anode cells, which exhibit exceptional sta-bility and durability in ZICs. Our experiments reveal a remarkable cycling performance, with a capacity retention of approximately 97.3% and a coulombic efficiency of nearly 100% even after 10,000 charge-discharge cycles. These findings signify significant progress in enhancing the performance of ZICs.

Purpose - Soil aggregates are of great significance to soil and water conservation and ecological environment construction in arid area of northwest district．Methods - Exploring the effects of different vegetation includes types and land use methods on the stability of soil aggregates in the Loess Plateau, and provide reference for the rational use and management of land, also the improvement of soil structure in the region. Select 9 types of samples of 0-30 cm of typical soil plots as the research objects, compare and analyze the particle size index, stability differences and anti-erodibility of soil aggregates under various vegetation cover. Results - The results show that P value, MWD value, GMD value, D value, and AI value of the 0-10cm surface soil all show the maximum value. As the depth increases, the size distribution of the above index values of each soil sample in the 10-20cm and 20-30cm layers is different; P value in the 0-30cm depth layer is linearly positively correlated with the AI value and MWD value, and linearly negatively correlated with the D value. The correlation coefficient R between each variable is in the range of 0.78-0.97, and the D value reflects the Loess Plateau area stability and erosion resistance of soil aggregates better. GMD and MWD value show an exponential relationship, the correlation coefficient R value of 10-20cm height layer is 0.46; AI and MWD value in 0-10cm, 20-30cm height layer have a power function relationship, 10-20cm height layer has a polynomial function, the correlation coefficient R value is 0.97. The scour coefficient of different soil samples has a high degree of dispersion, the maximum CV value is 1.92, and the minimum value is 0.49. Conclusions - The results of this study can provide a theoretical basis for the ecological and hydrological benefit evaluation of slope erosion control and vegetation restoration on the Loess Plateau.

Innovative interventions in the planning and design of stair and escalator facilities call for understanding their effects on stair use. This study considers five planning variables for the twinned stair and escalator facilities–stair pitch and width, angle of deviation, height and separating distance. Public sites were identified in 8 commercial districts in Beijing. Facilities (n=21) presenting heterogeneously across variables were sampled for simultaneous up and down pedestrian counts in 18 5-minute video segments middays, for a total of 1464 counts. Stair width accounts for 20% of the variance in ascending rate and 10% in descending. Plan angle accounts for 2% in ascending and 5% in descending, while pitch accounts for 1% in ascending and 5% in descending. The study confirms the effects of layout and design of stairway and escalator facilities on facility choice. The results point directly to interventions in support of higher stair-climbing rates.

The accumulation of foam cells in arterial intima and the accompanied chronic inflammation are considered major causes of neoatherosclerosis and restenosis. However, both the underlying mechanism and effective treatment for the disease are yet to be uncovered. In this study, we combined transcriptome profiling of restenosis artery tissue and bioinformatic analysis to reveal that NLRP3 inflammasome is markedly upregulated in restenosis and that several restenosis re-lated DEGs are also targets of mulberry extract, a natural dietary supplement used in traditional Chinese medicine to improve liver vitality. Further pathway enrichment analysis identified MAPK signaling pathway to be involved in the inflammatory response of foam cells. Consistently, immunofluorescence microscopy shows co-localization of NLRP3 with CD68+ macrophages. We then evaluated the efficacy of mulberry extract in inhibiting both the formation of foam cells and their inflammatory response. We demonstrated that mulberry extract suppresses the formation of ox-LDL induced foam cells, possibly by upregulating the cholesterol efflux genes ABCA1 and ABCG1 to inhibit intracellular lipid accumulation. In addition, mulberry extract dampens NLRP3 inflammasome activation by stressing the MAPK signaling pathway. Collectively, our mecha-nistic and functional studies unveil the therapeutic value of mulberry extract in neoatherosclerosis and restenosis treatment by regulating lipid metabolism and inflammatory response of foam cells.

Demethyleneberberine is an active component extracted from the Chinese herbal drug Cortex Phellodendri. It is also a metabolite of the berberine in animals and humans. However, the pharmacokinetics, tissue distribution and excretion of demethyleneberberine have not been reported. The present study aimed to investigate the pharmacokinetic parameters of demethyleneberberine by developing a method of high-performance liquid chromatography-tandem mass spectrometry (LC-MS/MS). The detection was performed by using positive ion electrospray ionization in multiple reaction monitoring mode. The MS/MS ion transitions were monitored at m/z 324.4→308.3 for demethyleneberberine and 465.5→350.3 for IS. After oral administration of demethyleneberberine in rats and mice, the pharmacokinetics, tissue distribution, and excretion of desmethylberberine in rats and mice were comparatively studied for the first time. The plasma concentration of desmethylberberine reached its peak within 5 min after oral administration in both rats and mice. The bioavailability of rats and mice was comparable, ranging from 4.47% to 5.94%, higher than that of berberine. The total excretion of desmethylberberine in urine, feces and bile is 7.28~9.77%. These findings provide valuable insights into the pharmacological and clinical research on desmethylberberine.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Predators are dependent on the capture of prey to meet their energetic and nutritive requirements, imposing a regime of predation risk. Consequently, prey experience both consumptive and non-consumptive effects. Non-consumptive effects may manifest through altered growth and ontogenetic trajectories of prey species, a dynamic modulated by olfactory or other sensory cues from predators. Bactrocera dorsalis Hendel represents a great invasive threat to global horticulture. While earlier research has primarily centered on the consumptive interactions between B. dorsalis and its natural enemies, the potential consequences of non-consumptive interactions on the development of B. dorsalis have been overlooked. In this study, we investigated the impact of predation risk effects, induced by both visual exposure to the predatory mantis Hierodula patellifera Serville and its associated odor, on the life history traits of B. dorsalis. Female B. dorsalis demonstrated reduced development time in the presence of isolated H. patellifera or H. patellifera odor, yet evidenced significantly increased fecundity. Conversely, males displayed no significant change in development time. Additionally, neither female nor male body weight at death was significantly influenced by predation risk from isolated predators or predator odor. These results indicated adaptive developmental strategies of B. dorsalis when faced with risks from predators and highlight the important role of predator odor, which has the potential to lay the groundwork for improving biological control efforts and innovative approaches within pest control.

To estimate the degree of quantum entanglement, it is important to understand the statistical behavior of functions of spectrum of density matrices such as von Neumann entropy, quantum purity, and entanglement capacity. These entangle- ment metrics over different generic state ensembles have been studied intensively in the literature. As an alternative metric, in this work we study sum of square root spectrum of density matrices, which is relevant to negativity and fidelity in quantum information processing. In particular, we derive the exact mean and vari- ance of sum of square root spectrum over the Bures-Hall generic state ensemble extending known results obtained recently over the Hilbert-Schmidt ensemble.

Accumulating literature demonstrates that omega-3 polyunsaturated fatty acid (N3PUFA) can be incorporated into the phospholipid bilayer of cell membrane in the human body to positively affect the cardiovascular system, including improving epithelial function, decreasing coagulopathy, and attenuating uncontrolled inflammatory responses and oxidative stress. Moreover, it has been proven that the N3PUFA, eicosapentaenoic acid (EPA) and docosahexaenoic acid (DHA), are precursors of some potent endogenous bioactive lipid mediators that mediate some favorable effects attributed to their parent substances. A linear dose-response relationship between increased EPA and DHA intake and reduced thrombotic outcomes have been reported. The excellent safety profile of dietary N3PUFA makes them a prospective adjuvant treatment for people exposed to a higher risk of cardiovascular problems associated with COVID-19. This review presented the potential mechanisms that might contribute to the beneficial effect of N3PUFA and the optimal form and dose applied.

Small peptides (SPs), ranging from 5 to 100 amino acids, play integral roles in plants due to their diverse functions. Despite their low abundance and small molecular weight, SPs intricately regulate critical aspects of plant life, including cell division, growth, differentiation, flowering, fruiting, maturation, and stress responses. As vital mediators of intercellular signaling, SPs have garnered significant attention in plant biology research. This comprehensive review delves into SPs' structure, classification, and identification, providing a detailed understanding of their significance. Additionally, we summarize recent findings on the biological functions and signaling pathways of prominent SPs that regulate plant growth and development. The review also offers a forward-looking perspective on future research directions in peptide signaling pathways.

Despite UAV multi-target detection exhibits considerable developmental potential worldwide, it suffers distinct challenges compared with traditional tasks in this field. These challenges include insufficient feature extraction capabilities for small targets, limited capabilities for multi-dimensional feature fusion, as well as constraints on hardware computation parameters. Especially in mission scenarios such as disaster detection, these challenges will be further amplified. Consequently, this paper introduces SSE-YOLO, an innovative YOLO framework algorithm specially designed to address these challenges. To enhance the model's feature extraction capability, we employ the SPDConv module to replace the original Conv in the backbone section, utilizing depth-separable convolution instead of traditional convolution pooling. Concurrently, we eliminate the SPPF module at the bottom and address a new Separate Kernel Attention Pyramid Pooling (SKAPP) module, substantially enhancing the feature fusion capability at the model's core. Moreover, to address the challenge of multi-dimensional feature fusion, we replace the Concat module of the neck and head with E-BiFPN, transmitting feature information from the backbone to the lower network through four CBS blocks, which effectively resolves the issue of lost contextual information in the model. Meanwhile, SSE-YOLO undergoes ablation experiments on the VisDrone2019 dataset to evaluate its effectiveness against alternative methods, and experimental results illustrate the model's exceptional precision in detecting UAV targets. In comparison to models with comparable experimental accuracy, SSE-YOLO requires remarkably fewer parameters. On the VisDrone2019-DET-test-dev dataset, SSE-YOLO enhances mAP by 17.3%, with a 42.5% reduction in the parameter amounts. Therefore, the proposed method effectively tackles the challenge of reconciling low parameters and high accuracy, presenting a novel pathway for deep learning-based UAV multi-target detection.

Incremental stability analysis for time-delay systems has attracted more and more attentions for its contemporary applications in transportation processes, population dynamics, economics, satellite positions, etc. This paper researches criteria on v(t)-incremental stability, which is defined to demonstrate the convergence rate for incremental stability, for time-delay systems. Firstly, the sufficient conditions for v(t)-incremental stability for time-delay systems with continuous right-hands are studied, and several corollaries for specific cases are provided. As for time-delay systems with discontinuous right-hands, after expounding the relevant conditions for the existence and uniqueness of the Filippov solution, by using approximation methods, sufficient conditions for v(t)-incremental stability are obtained. The conclusions are applied to linear switched time-delay systems and Hopfield neural network system with composite right-hand afterwards.

To address the severe distresses of asphalt pavement, a new type of pavement maintenance treatment, porous ultra-thin overlay (PUTO) with small particle size was proposed. The PUTO has a thickness of 1.5~2.5 cm and a large void ratio of 18~25%. As a newly asphalt mixture, the structure characteristics differ from traditional pavement. Therefore, it is necessary to investigated the fabrication schemes in laboratory and on-site, respectively. In this study, the optimal fabrication schemes, including compaction temperature and number of blows of PUTO were determined based on Cantabro test and volumetric parameters. Then, the corresponding relationship between laboratory and on-site compaction work was then established based on the energy equivalent principle. On this basis, the numbers of on-site rolling passes and the combination method were calculated. The results show that increased compaction temperature and number of blows reduce the height and enhance the compactness of the Marshall sample. With the same temperature and number of blows, the scattering resistance of coarse gradation (PAC-1) is better than that of fine gradation (PAC-2), and the increased asphalt viscosity significantly improves the scattering resistance of the asphalt mixture. To ensure the scattering resistance and volumetric characteristic, the initial compaction temperature of the PAC-1 and PAC-2 should not be lower than 150 °C and 165 °C, respectively. Then, the laboratory compaction work and on-site compaction work were calculated and converted based on the principle of energy equivalence. Consequently, the on-site compaction combination of rolling machines for four asphalt mixtures was determined. According to the volumetric parameters, the paving test section proved that the construction temperature and the on-site rolling combination determined by laboratory tests are reasonable, and ultra-thin overlay has good structural stability, drainage and skid resistance.

Pore-fractures network play a key role in coalbed methane (CBM) accumulation and production, while the impacts of coal facies on the pore-fractures network performance are still poorly understood. In this work, the research on the pore-fracture occurrence of 38 collected coals from Sangjiang-Muling coal-bearing basins with multiple techniques including mercury intrusion porosimetry (MIP), micro-organic quantitative analysis, and optic microscopy, and its variation controlling of coal face were studied. The MIP curves of 38 selected coals indicating pore structures were subdivided into three typical types including type I of predominant micropores, type Ⅱ of predominant micropores and macropores with good connectivity and type Ⅲ of predominant micropores and macropores with poor connectivity. For coal facies, there are three various coal facies were distinguished, which include lake shore coastal wet forest swamp, the upper delta plain wet forest swamp, tidal flat wet forest swamp with Q-cluster analysis and tissue preservation index - gelification index (TPI-GI) and Wood index - groundwater influence index (WI -GWI). The results show there is positive relationship between tissue preservation index (TPI), wood index (WI) and mesopores (102nm-103nm), while a negative relationship between TPI, WI and macropores/fractures. In addition, groundwater level fluctuations can control the development of type C and D fractures, and the frequency of type C and D fractures shows an ascending trend with increasing GWI, which may be caused by the mineral hydration of the coal. Finally, from the perspective of the pore-fractures occurrence in CBM reservoirs, the wet forest swamp of upper delta plain is considered to be the optimization areas for Sanjiang-Mulinghe coal-bearing basins by a comparative study of various coal facies.

The rapid development of multicopters has led to many security problems. In order to prevent multicopters from invading restricted areas or famous buildings, an Anti-UAV Defense System (AUDS) has been developed and become a research topic of interest. Topics under research in relation to this include electromagnetic interference guns for unmanned aerial vehicles (UAVs), high-energy laser guns, US military net warheads, and AUDSs with net guns. However, these AUDSs use either manual aiming or expensive radar to track UAVs. This paper proposes a dual-axis rotary platform with UAV automatic tracking. The tracking platform uses visual image processing technology to track and lock the dynamic displacement of a UAV. When a target UAV is locked, the system uses a nine-axis attitude meter and laser rangefinders to measure its flight altitude and calculates its longitude and latitude coordinates through sphere coordinates to provide UAV monitoring for further defense or attack missions. Tracking tests of UAV flights in the air were carried out using a DJI MAVIC UAV at a height of 30 meters to 100 meters. It was set up for UAV image capture and visual recognition for tracking under various weather conditions by a thermal imager and a full-color camera respectively. When there was no cloud during the daytime, the images captured by the thermal imager and full-color camera provide a high-quality image recognition result. However, under dark weather, black clouds will emit radiant energy and seriously affect the capture of images by a thermal imager. When there is no cloud at night, the thermal imager performs well in UAV image capture. When the UAV is tracked and locked, the system can effectively obtain the flight altitude and longitude and latitude coordinate values.

Wendan (a type of pomelo), as a popular fruit in China, is less known in other countries. Its peel is widely used in food and traditional medicine. Four different origins of Wendan pomelo were selected, and crude extracts were obtained by the Soxhlet extraction method. The composition of Wendan peel was analyzed by high-performance liquid chromatography-mass spectrometry (HPLC-MS) in positive ion mode. The compounds were identified by searching the Metabolite Link (METLIN), Spectral Database for Organic Compounds (SDBS) and referring to literature reports. A total of 20 compounds were identified among the samples from the four origins, of which 8 compounds were common. The majority of the compounds belonged to the flavonoid and coumarin classes, Meranzin hydrate was identified for the first time in pomelo peel. In vitro antioxidant activity experiments showed that samples from Taizhou, Zhejiang exhibited the highest antioxidant activity in the DPPH, ABTS, and FRAP assays, with values of 0.59 mg/mL, 97.06 μmol TE/g, and 60.62 μmol Fe2+/g, respectively. Samples from Zhangzhou, Fujian showed antioxidant activity second only to the samples from Taizhou, Zhejiang. The sample from Zhangzhou, Fujian Province, showed excellent inhibitory activity in the α-glucosidase inhibition assay (IC50=7.99 mg/mL).

Collapsibility is an inherent characteristic of loess, which is often treated by adding industrial materials such as cement and lime in engineering, it seriously damages the reclamation performance of soil. Degradable calcium lignosulfonate (CLS) has a good prospect in balancing soil stabilization and environmental protection. Therefore, this paper evaluates the collapsibility and mechanical characteristics of CLS improved loess based on the collapsibility test, grey correlation analysis, and unconfined compressive strength test. The results show that when the content is 3%, the stabilization effect is most obvious, and the collapsibility coefficient can be reduced by more than 95%. The order of grey correlation degree of collapsibility on each index is moisture content, void ratio, dry density, and CLS content from large to small. The unconfined compressive strength increases rapidly in the first 14 days and then decreases with the content. When the content is too high, the strength of improved loess is lower than that of plain loess. Combined with SEM, microstructure parameters, and X-ray diffraction analysis, the carbonate minerals can play the role of filling pores and connecting soil particles, which reduces the grain size of mineral composition and the thickness of the electric double layer and makes the structure more compact. The research results have scientific significance and application value for the ecological modification research and engineering application of soil.

As an important component of modern service industry, tourism is regarded as a "green" driver to regional economic growth and industrial upgrading. Applying the "quasi-natural experiment" advocated by the “The Belt and Road” Initiative, this paper, based on the method of DID, as-sessed the influence of this initiative on regional tourism development by analyzing panel data collected from 286 prefecture-level cities in China over the period of 2007-2018. It is found that the "The Belt and Road" initiative has stimulated market dynamics and promoted tourism de-velopment in the regions along the route, and has significantly improved indicators such as per capita domestic and inbound tourism revenue and per capita domestic and inbound tourist re-ceipt. Also, the degree of contribution of domestic tourists to the tourism economy of the re-gions where the policy has been implemented is stronger than that of inbound tourists. In sum, the results of this paper not only confirm that the “The Belt and Road” Initiative has significantly contributed to the high-quality tourism development of Chinese provinces along the routes, but also provide important policy enlightenment for the upgrading of regional tourism industry and regional economic balance.

Purpose The objective of this study was to eliminate any ambiguity by examining the correlation between gut microbiota and both AMD and glaucoma. Methods Mendelian randomization studies were conducted utilizing the data sourced from the GWAS database for the gut microbiome, AMD, and glaucoma. SNP estimates were summarized through five MR methods. We utilized Cochran's Q statistic to evaluate the heterogeneity of the instrumental variables. Additionally, we employed a "leave-one-out" approach to verify the stability of our findings. Results IVW suggests that Eubacterium (oxidoreducens group) and Parabacteroides had a protective effect on AMD. Both weighted median and IVW suggests that Lachnospiraceae (NK4A136 group) and Ruminococcaceae (UCG009) had a protective effect on AMD. However, both weighted median and IVW suggests that Dorea had a risk effect on AMD. Similarly, The IVW of Eubacterium (ventriosum group) showed a risk effect on AMD. The weighted median of Eubacterium (nodatum group), Lachnospiraceae (NC2004 group), and Roseburia had a risk effect on glaucoma. IVW suggested that Ruminococcaceae (UCG004) had a risk effect on glaucoma. Reverse MR analysis found a causal link between Eubacterium (nodatum group) and glaucoma. No causal relationships were found between AMD or glaucoma and the other mentioned bacterial groups. No significant heterogeneity or evidence of horizontal pleiotropy was detected. Conclusions This study found that certain gut bacteria had protective effects on AMD, while others may be risk factors for AMD or glaucoma. Besides, reverse MR found that glaucoma led to increased abundance of certain gut bacteria. Further trials are needed to clarify the specific mechanisms involved.

Compared to the southern Tibetan Plateau, the northern part has been regarded as relatively lacking geothermal resources. However, there is no lack of natural hot springs exposed in beads along large-scale fracture systems, and research on them is currently limited to individual hot springs or geothermal systems. This paper focuses on the Wahongshan-Wenquan Fracture Zone (WWFZ), analyzes the formation of five hydrothermal activity zones along the fracture zone in terms of differences in the hydrochemical and isotopic composition of the hot water, and then explores the hydrothermal control of hot springs in the zone by the fracture. The results show that the main Fractures of WWFZ is the regional heat-control structures, and the fracture system formed by a small number of near-north-south and near-east-west fractures transversal to it provides a favorable channel for deep hydrothermal convective circulation. Ice and snow melt water from the Ngola Shan Mountains, with an average elevation of more than 4,500 meters above sea level, infiltrates along the fractures and is heated by deep circulation to form deep geothermal reservoirs. There is no detectable contribution of mantle source heat to the hot spring gases, and the heat source is mainly natural heat conduction warming, but the "Low-Velocity body (LVB)" in the middle and lower crust of the area may be the primary heat source of the high geothermal background in the area. The hydrochemical components of the hot springs in the area show a certain regularity, and the main ionic components, TDS and water temperature, tend to increase away from the main rupture, reflecting the controlling effect of the WWF on the hydrothermal transport in the area. In the future, the geothermal work in this area should focus on the hydrothermal control properties of different levels, the nature of fractures in the area, and the thermal contribution of LVB in the middle and lower crust.

Brown-Spotted Pit viper (Protobothrops mucrosquamatus), also known as the Chinese habu, is a widespread and highly venomous snake distributed from from northeastern India to eastern China. Genomics research can help provide much insight in understanding venom components and natural selection in vipers. Here, we collected, sequenced and assembled the genome of a male P. mucrosquamatus individual from China, producing a highly continuous reference genome, with the length of 1.53 Gb and 41.18% repeat element content. From this 24,799 genes were identified, and 97.97% genes could be annotated. Nuclear genome single-copy genes phylogenetic tree including 6 species verified the validity of our genome assembly and annotation process. This research will contribute to further study on Protobothrops biology and the genetic basis of the snake venom.

The water resources carrying capacity (WRCC) system comprises multiple complex and nonlinear interactions related to society, economy, water resources and the water environment. A full understanding of its internal mechanism is conducive to the further improvement of the regional WRCC. This article focuses on the temporal and spatial variability of WRCC to explore a method of dynamic successive assessment. Firstly, the Pressure-State-Response (PSR)framework is used to develop a systematic and causal indicator system. Then, The Variable Fuzzy Pattern Recognition (VFPR) model and an analytic hierarchy process-entropy (AHP-E) model are combined to successively and dynamically assess WRCC. The proposed method is applied to the dynamic successive assessment of WRCC in Hebei Province, and it is obtained that the poor water resources carrying capacity in Hebei Province is mainly due to the basic attribute of the decision of the water resources shortage, but Hebei Province actively adopts a variety of measures to save water and pressurize mining, which makes the province's water resources carrying capacity have a tendency to become better gradually. At the same time, the system dynamics model (SD) of water resources carrying capacity based on the analysis of the model structure was established. Moreover, three scenarios were designed, including existing continuation, high-efficiency water-saving, cross-regional water transfer and coordinated development, each scenario divided into high and low-speed economic development and population growth schemes, then total 6 schemes between 2023 and 2030 were simulated and predicted respectively. The results indicate that if the current development model is adopted, the water resource carrying capacity will continue to maintain low levels. It was concluded that the high-speed development of economy and population, the efficient water conservation and inter-basin transfer scenario (scenario 2 with high-speed) is the best choice for sustainable development of water resources and social economy in Hebei.

Interferon regulatory factor 5 (IRF5) is known to be involved in the innate immune response and pro-inflammatory cytokines. However, the roles of IRF5 in immune responses in Malabar grouper (Epinephelus malabaricus) have not been extensively explored. In this study, IRF5 gene was identified and characterized from M. grouper. The full-length IRF5 cDNA consisted of a 5’ terminal untranslated region (5’-UTR) of 289 bp and a 3’-UTR of 542 bp, an open reading frame (ORF) of 1500 bp encoding a polypeptide of 499 amino acids with a predicted molecular mass of 56.28 kDa and isoelectric point (pI) of 5.2. The putative MgIRF5 protein consists of four important conserved domains: a helix DNA-binding domain (DBD) at the N-terminus, a middle region, an IRF association domain (IAD) and a virus activated domain (VAD) at the C-terminus. Sequence alignment and phylogenetic analysis showed that highest sequence similarity of IRF5 was observed between the IRF5 genes from Oplegnathus fasciatus and Miichthys miiuy. The mRNA transcripts of IRF5 were detected in a wide range of tissues types from healthy M. grouper with highest expression in muscle, liver and skin. After treatment with poly (I: C), it was significantly up-regulated in spleen and liver tissues. When infected with NNV, the expression level of MgIRF5 was up-regulated in spleen and head kidney and their transcriptional responses to IRF5 increased in the grouper kidney cells. This approach suggests that MgIRF5 is important in the underlying mechanism of the innate immune responses against antiviral response.

The natural products and conventional chemotherapeutic drugs are believed to increase the cure rates of anti-cancer treatment while reducing their toxicity. The current study investigates the cytotoxic and apoptogenic effects of bioactive compounds from Monotheca buxifolia on Hep G2 cell lines. The effect on the viability of Hep G2 cells was evaluated by MTT assay; Morphological changes were studied, the apoptotic activity was demonstrated through Annexin-V-FITC/ PI, a molecular dynamics simulation study was conducted to explore the binding pattern of the compounds in the active site of the PPRAδ protein. The isolated compounds lauric acid, oleanolic acid, and bis(2-ethylhexyl) phthalate inhibited the growth of hepatocellular cancer cells, as determined by MTT assay and annexin V-FITC/PI. The IC50 value for lauric acid was 56.4584 ± 1.20 µg/ml, that for oleanolic acid was 31.9421 ± 1.03 µg/ml, and that for bis(2-ethylhexyl) phthalate was 83.8019 ± 2.18 µg/ml. After 24 h of treatment, 29.5% of Hep G2 cells treated with lauric acid, 52.1% of those treated with oleanolic acid, and 22.4% of those treated with bis(2-ethylhexyl) phthalate were apoptotic. Morphological assay and Hoechst staining microscopy revealed the morphological alterations of cell membrane accompanied by nuclear condensation after treatment. The high fluctuation indicates the high potency and adopting various interactions, and vice versa, the oleanolic acid showed highly residues fluctuation, which remains stable in the active site of PPARδ protein and involved in various interactions while remaining locally fluctuated in the binding site the other two compounds. In conclusion, a significant apoptogenic effect was exhibited by lauric acid, oleanolic acid, and bis(2-ethylhexyl) phthalate against HepG2 cells in inducing apoptosis. Our findings indicate that these bioactive compounds hold promise as potential therapeutic for hepatocellular carcinoma.

LC-SPIK is a liver cancer-specific isoform of Serine Protease Inhibitor Kazal and has been proposed as a new biomarker for the detection of HCC given its unique 3-D structure which differs from normal pancreatic SPIK. An ELISA technology based on its unique structure was developed to use LC-SPIK as an effective biomarker for the clinical diagnosis of HCC. AFP, the most widely used biomarker for HCC surveillance currently, suffers from poor clinical performance, especially in the detection of early-stage HCC. In one case-control study, which included 164 HCC patients and 324 controls, LC-SPIK had an AUC of 0.87 compared to only 0.70 for AFP in distinguishing HCC from liver disease controls (cirrhosis, HBV/HCV). LC-SPIK also performed significantly better than AFP for the 81 patients with early-stage HCC (BCLC stage 0 and A), with an AUC of 0.85 compared to only 0.61 for AFP. Cirrhosis is the major risk factor for HCC, about 80% of patients with newly diagnosed HCC have preexisting cirrhosis. LC-SPIK’s clinical performance was also studied in HCC patients with viral and non-viral cirrhosis including cirrhosis caused by nonalcoholic fatty liver disease (NAFLD) and alcoholic liver disease (ALD). In a total of 163 viral cirrhosis patients with 93 HCC patients (50 early-stage), LC-SPIK had an AUC of 0.85, while AFP had an AUC of 0.70. For patients with early-stage HCC, LC-SPIK had a similar AUC of 0.83, while AFP had an AUC of only 0.60. For 120 patients with nonviral cirrhosis, including 62 HCC (23 early-stage) patients, LC-SPIK had an AUC of 0.84 while AFP had an AUC of only 0.72. For the 23 patients with early-stage HCC, LC-SPIK had a similar AUC of 0.83, while the AUC for AFP decreased to 0.65. All these results suggest that LC-SPIK has significantly better performance in the detection of HCC than AFP in all etiologies of liver diseases. In addition, LC-SPIK accurately detected the presence of HCC in 71%-91% of HCC patients with false-negative AFP test results in viral associated HCC and non-viral associated HCC.

When overhead lines are impacted by lightning, the traveling wave of the fault contains a wealth of fault information. The accurate extraction of feature quantities from transient components and their classification is fundamental to the identification of lightning faults. The extraction process may involve modal aliasing, optimal wavelet base issues, and inconsistencies between the lightning strike distance and the fault point, which have the potential to impact the effectiveness of recognition. This paper presents a method for identifying lightning strike faults by utilizing Kullback-Leibler (KL) divergence enhanced Variational Mode Decomposition (VMD) and Symmetric Geometry Mode Decomposition (SGMD) improved with Permutation Entropy (PE) to address the aforementioned issues. A model of a 220 kV overhead line is constructed using real faults to replicate scenarios of winding strike, counterstrike, and short-circuit. The three-phase voltage is chosen and then sub-jected to Karenbaren decoupling in order to transform it into zero mode, line mode 1, and line mode 2. The zero mode voltage is decomposed using KL-VMD and PE-SGMD methods, and lightning identification criteria are developed based on various transient energy ratios. The research findings demonstrate that the criteria effectively differentiate between winding strike, counterstrike, and short-circuit faults, thus confirming the accuracy and efficacy of the lightning fault identification criteria utilizing KL-VMD and PE-SGMD.

Space instable target simulator (SITS) is a vital actuator for ground verification of on-orbital capture technology, the motion performance of which directly affects simulation credibility. Different delays reduce the stability of SITS and ultimately lead to its divergence. In order to achieve high fidelity simulation, the impact of force measurement delay, discrete control cycle, and simulator response delay on stability is analyzed firstly. Then, the dynamic equation and transfer function identification model of hybrid simulator is constructed, and the necessary and sufficient conditions of its stability and convergence are obtained using the Routh criterion. After that, a switching compensator with variable gain is proposed, the compensation principle diagram of which is build, and its mathematical model including the energy observer and tracking differentiator is also established. Finally, three sets of numerical simulations are conducted to validate the correctness of the stability analysis and effectiveness of proposed compensation method. Simulation results show that all three types of delay can cause SITS to lose stability under critical stable motion state, and the delay in force measurement has the greatest impact, followed by the influence of control cycle. Compared with the force applied to simulated target, velocity and its recovery coefficient of space instable target using fixed gain and linear gain compensation, the proposed compensator has significantly better performance.

Histone Lysine Specific Demethylase 1 (LSD1) is overexpressed in many cancers and become a new target for anticancer drugs. In recent years, the small molecule inhibitors with various structures targeting LSD1 have been reported. Here we report the binding interaction modes of a series of thieno[3,2-b]pyrrole-5-carboxamides LSD1 inhibitors using molecular docking, three dimensional quantitative structure-activity relationship (3D-QSAR). Comparative molecular field analysis (CoMFA q²=0.783, r²=0.944, r²_pred=0.851) and Comparative molecular similarity indices analysis (CoMSIA q²=0.728, r²=0.982, r²_pred=0.814) were used to establish 3D-QSAR models, which had good verification and prediction capabilities. Based on the contour maps and the information of molecular docking, 8 novel small molecules were designed in silico, among which compounds D4, D5 and D8 with high predictive activity were subjected to further molecular dynamics simulations (MD), and their possible binding modes were explored. It was found that Asn535 plays a crucial role in stabilizing the inhibitors. Furthermore, the ADME and bioavailability prediction for D4, D5 and D8 were carried out. The results would provide valuable guidance for designing new reversible LSD1 inhibitors in the future.

Soil is an extremely significant resource for human survival, and agglomerates, as the basic unit of soil structure, not only enhance soil fertility and control the biological validity of nutrients, but also strengthen the soil's erosion resistance. The mass application of fertilizers may have a significant impact on crop growth and soil structure, and the rational application and dispensing of fertilizers will be an urgent issue to be addressed. Therefore, the effect of fertilizer application on the stability of water-stable soil aggregates needs to be studied under different meteorological and soil conditions to draw more general and feasible conclusions. Our Meta-analysis of data from 220 of 56 published studies found that fertilizer application increased mean weight diameter (MWD) by an average of 18% compared to the no-fertilizer treatment. Among the nitrogen (N), phosphate (P), and organic (OM) fertilizer treatments, the organic fertilizer treatment had a greater stimulatory effect on MWD (26%). Among the different fertilizer levels, low level of phosphorus (<40kg·hm-2·yr-1), high level of N (>120kg·hm-2·yr-1), and low level of organic fertilizer (<5000kg·hm-2·yr-1) increased MWD by 19%, 14%, and 41% respectively. Across soil types and land use types, the response to MWD was positive for red soils and paddy fields, and the stimulatory effect of organic fertilizer was more significant compared to chemical fertilizer. The regression model showed that the response ratio of MWD was negatively correlated with the response ratio of soil pH and bulk density (BD), and positively correlated with the response ratio of soil organic carbon (SOC) and microbial mass carbon (MBC). Meanwhile, the PLS-SEM model showed that average annual temperature was the main factor affecting the stability of soil aggregates, and the average annual rainfall is the secondary factor. Therefore, this study found that the long-term use of organic fertilizers in place of some chemical fertilizers was more effective than chemical fertilizer alone. Temperature and rainfall have greater effects on the response of fertilizer to soil aggregate stability.

A simple and effective surface modification of polyester fabrics with sulfuric acid to improve the interfacial deposition of polypyrrole was presented in our work. A range of sulfuric acid concentrations were analyzed by studying water contact angle. Effect of sulfuric acid modification on the deposition of polypyrrole was investigated by sheet resistance and color depth of fabric samples. Polyester fabrics coated with polypyrrole layer were confirmed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-Ray diffraction spectra (XRD), Fourier transform infrared spectroscopy (FTIR). XPS showed that sulphur containing functional groups were obviously appeared on the polyester fiber surface after modification, which were advantageous to promote the deposition of polypyrrole onto polyester fabrics. The improved deposition increased electrical conductivity of fabric samples.

During Sep. 2011, forty-four Leymus chinensis culms with stroma development were collected from Inner Mongolia. Stromata surrounded the flag leaf sheathes, white, at the final stage of development. Perithecium but not asci were observed under microscope. Nine epichloid endophyte strains were obtained from Tongliao subdivision, and sixteen from Horqin. Morphological and phylogenetic properties of these strains were investigated. Morphological properties of these strains were similar among these 27 strains. Colonies could grow to 28.5~41.1 mm/21d at 25℃; phialides 24.1~26.4 μm long, 2.1~2.5 μm at base, tapering to less than 1.0 μm at tip; conidia reniform to elliptical, 4.7~5.5×2.8~3.5 μm, indicating typical properties of Epichloë endophytes. Based on the sequences of tefA and tubB gene fragments, strains isolated from Inner Mongolia formed a distinct subclade in E. bromolica/ E. yangzii clade, with a bootstrap value of 66% and 64% respectively. Considering morphological and phylogenetic properties, we tend to determine strains isolated from Leymus chinensis as a new taxon. The detailed taxonomic position of this taxon needs further investigations on hybridization or genomic sequence.

This present study was designed to find out whether the acankoreagenin showed the antidiabetic and renoprotective effects in streptozotocin (STZ)-induced diabetic nephropathy (DN) rats. Type I diabetes was induced by a single intraperitoneal injection of STZ (70 mg/kg). At the end of the experiment, rats were euthanized and serum/plasma was separated for the determination of glucose, insulin, glycated hemoglobin A1c (HbA1c), C-peptide, biochemical parameters, and kidney function. One kidney was used for determining glutathione, superoxide dismutas, malondialdehyde, and tumor necrosis factor-alpha levels. The other kidney and pancreas were used for histopathological studies and immunohistochemical measurement of transforming growth factor beta (TGF-β) or NF-κB. Acankoreagenin (2 mg/kg) treatments led to a significant reduction in blood glucose assessed via oral glucose tolerance test (OGTT) in diabetic rats at 2 h. The treatment also resulted in improved body weight, decreased HbA1c, restored lipid profile, and renal oxidative stress. By inhibiting NF-κB, the release of proinflammatory cytokines was suppressed and by inhibiting TGF-β, the renal fibrosis was suppressed in STZ-induced diabetic rat model. Histopathological injury was also observed in pancreatic and renal tissues. These findings support the beneficial effect of acankoreagenin treatment in DN, which could be attributed to its antidiabetic and renoprotective effects.

IMPORTANCE: On December 10, 2021, the FDA published a Determination Letter, along with a Statistical Review and Evaluation Report, and concluded that under the non-informative prior, the local Bayesian optimal interval design (BOIN) design, in its revised form, can be designated fit-for-purpose for identifying the maximum tolerated dose of a new drug, assuming that dose-toxicity relationship is monotonically increasing. Although setting the BOIN design parameter p.tox = 1.4 * target.DLT.rate is recommended in almost all BOIN methodology articles and is the default value in the R package BOIN, it's unclear if the choice of p.tox should only depend on the target DLT rate and if certain range of p.tox could produce the same BOIN boundary table. DESIGN: In this simulation study, following parameters were varied one at a time, using R package BOIN, to explore their effects on the equivalence intervals of p.saf and p.tox: 1) target DLT rate, 2) n.earlystop, 3) cutoff.eli, 4) cohortsize, and 5) ncohort. And a simple 3+3 design was used as an example to explore equivalent sets of BOIN design parameters that can generate the same boundary table. RESULTS: When the early stopping parameter n.earlystop is relatively small or the cohortsize value is not optimized via simulation, it might be better to use p.tox < 1.4 * target.DLT.rate, or try out different cohort sizes, or increase n.earlystop, whichever is both feasible and provides better operating characteristics. This is because if the cohortsize was not optimized via simulation, even when n.earlystop = 12 and cohortsize > 3, the BOIN escalation/de-escalation rules generated using p.tox = 1.4 * target.DLT.rate could be exactly the same as those calculated using p.tox > 3 * target.DLT.rate, which might not be acceptable for some pediatric trials targeting 10% DLT rate. The traditional 3+3 design stops the dose finding process when 3 patients have been treated at the current dose level, 0 DLT has been observed, and the next higher dose has already been eliminated. If additional 3 patients were required to be treated at the current dose in the situation described above, the decision rules of this commonly used 3+3 design could be generated using BOIN design with target DLT rates ranging from 18% to 29%, p.saf ranging from 8% to 26%, and different p.tox values ranging from 39% to 99%. These BOIN parameters also need to satisfy a set of conditions. Meaning: This study demonstrates the importance of interpreting BOIN design parameter p.tox as an interval of toxicity rates that are considered too toxic, rather than one prespecified value that corresponds to the lowest toxicity probability that is deemed overly toxic. When designing a dose-finding trial using BOIN, it is important to perform simulation studies to identify equivalent sets of BOIN design parameters that can generate the same boundary table so that we can better compare the safety properties of different boundary tables.

Primary ovarian ependymoma is a rare neuroectodermal neoplasm that can arise from immature ovarian teratoma. Due to the paucity of this entity, a complete molecular analysis of these tumors has not been done, thus creating a challenge for finding an effective and safe therapeutic treatment. In limited literature, patient with primary ovarian ependymoma showed various responses to an array of individualized therapies ranging from surgeries and chemotherapies. Here, we present a 38-year-old female with persistent ovarian ependymoma with molecular profile similar to traditional central nervous system ependymoma that is irresponsive to multiple cytoreduction and clinical experimental therapies. Therefore, a prompt recognition and reporting of this entity can greatly aid in expanding the understanding and standardization of therapies for this neoplasm.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

As the general acceptance of fiber-reinforced polymer (FRP) in the concrete construction industry continues to rise, it is increasingly imperative that the crack width of FRP reinforced concrete members of pavement and girder be predicted with good accuracy due to strengthening of RC pavement, slabs or beams structures using FRP is known to control crack width. However, no specific provisions are provided by most international design codes for predicting crack width in FRP reinforced concrete flexure members. In this paper, five formulas for predicting the crack width for FRP reinforced structures are derived from three common computational theories which including statistical method, comprehensive theory, and bond-slip theory. The formula of statistical method is simplest, but the parameters depend on much sample data. The comprehensive and slippage theory based on semi-empirical statistical crack spacing are obtained through the calculation of non-uniformity coefficient of strain. The comprehensive and slippage theory based on semi-empirical axial force balance are obtained through the calculation of tensile reinforcement factor. The comparative analysis of performance of five formulas is carried out. The results indicate that the formula from comprehensive theory based on semi-empirical statistical crack spacing is recommended for predicting the crack width of FRP reinforced concrete flexural structure.

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, the molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopores imbibition during shut-in for a typical shale reservoir Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between “interfacial water molecules” at the imbibition front and “adsorbed oil molecules” on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil especially the heavy hydrocarbon component in the adsorbed layer tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore's wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for “interfacial water molecules” to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect of pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for EOR.

Seismic velocity inversion is one of the most critical issues in the field of seismic exploration and has long been the focus of numerous experts and scholars. In recent years, the advancement of machine learning technologies has infused new vitality into the research of seismic velocity inversion and yielded a wealth of research outcomes. Typically, seismic velocity inversion based on machine learning lacks control over physical processes and interpretability. Starting from wave theory and the physical processes of seismic data acquisition, this paper proposes a method for seismic velocity model inversion based on Physical Embedding Recurrent Neural Networks. Firstly, the wave equation is a mathematical representation of the physical process of acoustic waves propagating through a medium, and the finite difference method is an effective approach to solving the wave equation. With this in mind, we introduce the architecture of recurrent neural networks to describe the finite difference solution of the wave equation, realizing the embedding of physical processes into machine learning. Secondly, in seismic data acquisition, the propagation of acoustic waves from multiple sources through the medium represents a high-dimensional causal time series (wavefield snapshots), where the influential variable is the velocity model, and the received signals are the observations of the wavefield. This forms a forward modeling process as the forward simulation of the wavefield equation, and the use of error back-propagation between observations and calculations as the velocity inversion process. Through time-lapse inversion and incorporating the causal information of wavefield propagation, the non-uniqueness issue in velocity inversion is mitigated. Through mathematical derivations and theoretical model analyses, the effectiveness and rationality of the method are demonstrated. In conjunction with simulation results for complex models, the method proposed in this paper can achieve velocity inversion in complex geological structures.

Hessenberg differential algebraic equations (Hessenberg-DAEs) with high index play a critical role in the modeling of mechanical systems and multibody dynamics. Motivated by the widely used Lie Group Differential Algebraic Equation (LGDAE) method which only handles index 2 systems, we propose a Modified Extended Lie Group Differential Algebraic Equation (MELGDAE) method for solving index 3 Hessenberg-DAEs, and provide theoretical analysis to deepen the foundation of the MELGDAE method.The performance of the MELGDAE method is compared with the standard methods RADAU and MEBDF on index 2 and 3 DAE systems, and it is demonstrated that the MELGDAE integrator exhibits competitive performance in terms of high accuracy and the preservation of algebraic constraints. In particular, all differential variables in index 3 Hessenberg DAEs achieve second-order convergence using the MELGDAE method, which suggests potential for extension to Hessenberg-DAEs with an index of 4 or higher.

The Ras family of proteins is tethered to the inner leaflet of the cell membranes which play an essential role in signal transduction pathways that promote cellular proliferation, survival, growth, and differentiation. KRas-4B, the most mutated Ras isoform in different cancers, has been under extensive study for more than two decades. Here we have focused our interest on the influence of cholesterol on the orientations that KRas-4B adopts with respect to the plane of the anionic model membranes. How cholesterol in the bilayer might modulate preferences for specific orientation states is far from clear. Herein, after analyzing data from in total 4000 ns-long MD simulations for four KRas-4B systems, properties such as the area per lipid and thickness of the membrane as well as selected radial distribution functions, penetration of different moieties of KRas-4B, and internal conformational fluctuations of flexible moieties in KRas-4B have been calculated. It has been shown that high cholesterol content in the PM favors OS1, exposing the effector-binding loop for signal transduction in the cell from the atomic level. We confirm that high cholesterol in the PM helps KRas-4B mutant stay in its constitutively active state, which suggests that high cholesterol intake can increase mortality and may promote cancer progression for cancer patients. We propose that during the treatment of KRas-4B-related cancers, reducing the cholesterol level in the PM and sustaining cancer progression by controlling the plasma cholesterol intake might be taken into account in anti-cancer therapies.

We introduce and investigate a simple and explicitly mechanical model of Maxwell's demon -- a device that interacts with a memory register (a stream of bits), a thermal reservoir (an ideal gas) and a work reservoir (a mass that can be lifted or lowered). Our device is similar to one that we have briefly described elsewhere [1], but it has the additional feature that it can be programmed to recognize a chosen reference sequence, for instance, the binary representation of $\pi$. If the bits in the memory register match those of the reference sequence, then the device extracts heat from the thermal reservoir and converts it into work to lift a small mass. Conversely, the device can operate as a generalized Landauer's eraser (or copier), harnessing the energy of a dropping mass to write the chosen reference sequence onto the memory register, replacing whatever information may previously have been stored there. Our model can be interpreted either as a machine that autonomously performs a conversion between information and energy, or else as a feedback-controlled device that is operated by an external agent. We derive generalized second laws of thermodynamics for both pictures. We illustrate our model with numerical simulations, as well as analytical calculations in a particular, exactly solvable limit.

In this paper, a new approach is proposed for designing ultra-low-power FFT (Fast Fourier Transform) system suitable for use in energy harvesting powered sensors. Bit-serial architecture is adopted to reduce the power consumption of butterfly operation. Simulation results show that, compared with state-of-the-art bit-serial and conventional parallel processors, the proposed technique is superior in terms of silicon area, power consumption, dynamic energy use due to variable precision arithmetic. A sample design of a 64-point FFT shows that the implementation can save about 40% area and 36% leakage power compared with a conventional parallel counterpart, accordingly achieving significant power benefits at a low sample rate and low voltage domain. The dynamic variation of the arithmetic precision can be achieved through a simple modification of the controller with hardware area overhead of 10% gate count.

Over the past decades, overweight and obesity has become a global epidemic and the leading threat for death. To prevent the serious risk, an overweight or obese individual must apply a long-term weight-management strategy to control food intake and physical activities, which is however, not easy. Recently, with the advances of information technology, more and more people can use wearable devices and smartphones to obtain physical activity information, while they can also access various health-related information from Internet online social networks (OSNs). Nevertheless, there is a lack of an integrated approach that can combine these two methods in an efficient way. In this paper, we address this issue and propose a novel mobile-social framework for health recognition and recommendation, namely, H-Rec². The main ideas of H-Rec² include (1) to recognize the individual's health status using smartphone as a general platform, and (2) to recommend physical activity and food intake based on personal health information, life science principles, and health-related information obtained from OSNs. To demonstrate the potentials of the H-Rec² framework, we develop a prototype that consists of four important components: (1) an activity recognition module that senses physical activity using accelerometer, (2) a health status modeling module that applies a novel algorithm to generate personalized health status index, (3) a restaurant information collection module that collects relevant information from OSN, and (4) a restaurant recommendation module that provides personalized and context-aware recommendation. To evaluate the prototype, we conduct both objective and subjective experiments, which confirm the performance and effectiveness of the proposed system.

Soil organic matter is an important component that reflects soil fertility and promotes plant growth. The soil of typical Chinese tea plantations was used as the research object in this work, and by combining soil hyperspectral data and image texture characteristics, a quantitative prediction model of soil organic matter based on machine vision and hyperspectral imaging technology was built. Three methods, standard normalized variate (SNV), multisource scattering correction (MSC) and smoothing, were first used to preprocess the spectra. After that, random frog (RF), variable combination population analysis (VCPA) and variable combination population analysis and iterative retained information variable algorithm (VCPA-IRIV) algorithms were used to extract the characteristic bands. Finally, the quantitative prediction model of nonlinear support vector regression (SVR) and linear partial least squares regression (PLSR) for soil organic matter was established by combining nine color features and five texture features of hyperspectral images. The outcomes demonstrate that, in comparison to single spectral data, fusion data may greatly increase the performance of the prediction model, with MSC+VCPA-IRIV+SVR (R2C=0.995, R2P=0.986, RPD=8.155) being the optimal approach combination. This work offers excellent justification for more investigation into nondestructive methods for determining the amount of organic matter in soil.

This research focuses on the Hopf bifurcation occurring at a singular point with high-order degeneracy in a class of three-dimensional systems. Based on center manifold theorem, by expanding the technique for determining singular point values of degenerate singularities in two-dimensional systems, the formal series method to determine the singular point values at the high-order degenerate critical point is discussed. Furthermore, a class of specific three-dimensional differential systems with high-order degenerate singularities is explored. By computing the singular point values and determining center conditions, we proved that a minimum of 5 small-amplitude limit cycles in the vicinity of the origin. This research provides new perspectives on the center problem and limit cycle bifurcation in high-dimensional systems with high-order degenerate singular points.

The majority of cellular responses to external stimuli are mediated by receptors such as G protein-coupled receptors (GPCRs) and systems including endoplasmic reticulum stress (ER stress). Since GPCR signalling is pivotal in numerous malignancies, they are widely targeted by a number of clinical drugs. Cancer cells often negatively modulate GPCRs in order to survive, proliferate and to disseminate. Similarly, numerous branches of the unfolded protein response (UPR) act as pro-survival mediators and are involved in promoting cancer progression via mechanisms such as epithelial to mesenchymal transition (EMT). However, there are a few proteins among these groups which impede deleterious effects by orchestrating the pro-apoptotic phenomenon and paving a therapeutic pathway. The present review exposes and discusses such critical mechanisms and some of the key processes involved in carcinogenesis.

To realize fast and effective synthetic aperture radar (SAR) deception jamming, a high-quality SAR deception jamming template library can be generated by performing sample augmentation on SAR deception jamming templates. However, current sample augmentation schemes of SAR deception jamming templates face certain problems. First, the authenticity of templates is low due to the lack of speckle noise. Second, the generated templates have low similarity to the target and shadow areas of the input templates. To solve these problems, this study proposes a sample augmentation scheme based on generative adversarial networks, which can generate a high-quality library of SAR deception jamming templates with shadows. The proposed scheme solves the two aforementioned problems from the following aspects. First, the influence of the speckle noise is considered in the network to avoid the problem of reduced authenticity in generated images. Second, a channel attention mechanism module is used to improve the network's learning ability of shadow features, which improves the similarity between the generated template and the shadow area in the input template. Finally, the proposed scheme and the SinGAN scheme are compared regarding the equivalent numbers of looks and the structural similarity between the target and shadow in the sample augmentation results. The comparison results demonstrate that, compared to the templates generated by the SinGAN scheme, those generated by the proposed scheme have targets and shadow features similar to those of the original image, and can incorporate speckle noise characteristics, resulting in higher authenticity, which helps to achieve fast and effective SAR deception jamming.

Maritime ship monitoring plays an important role in maritime transportation. Fast and accurate detection of maritime ship is the key to maritime ship monitoring. The main sources of marine ship images are optical images and synthetic aperture radar (SAR) images. Different from natural images, SAR images are independent to daylight and weather conditions. Traditional ship detection methods of SAR images mainly depend on the statistical distribution of sea clutter, which leads to poor robustness. As a deep learning detector, RetinaNet can break this obstacle, and the problem of imbalance on feature level and objective level can be further solved by combining with Libra R-CNN algorithm. In this paper, we modify the feature fusion part of Libra RetinaNet by adding a bottom-up path augmentation structure to better preserve the low-level feature information, and we expand the dataset through style transfer. We evaluate our method on the publicly available SAR dataset of ship detection with complex backgrounds. The experimental results show that the improved Libra RetinaNet can effectively detect multi-scale ships through expansion of the dataset, with an average accuracy of 97.38%.

Anthracnose is one of primary diseases in tea plants that affects tea yield and quality. The geographical distribution, occurrence regularity, and agronomic measures of tea plants with anthracnose have been researched for decades. However, the pathogenic cause of anthracnose in tea plants is diverse in different regions of the world. Identifying the specific pathogenic fungi causing tea anthracnose is an essential control measure to mitigate this disease. In this study, 88 Diaporthales and 45 Colletotrichum isolates were obtained from 3 different types of diseased tea leaves. Based on multilocus phylogenetic and morphological analysis, 3 known species, including Discula theae-sinensis, Diaporthe ueckerae, Diaporthe lithocarpus, and 3 indistinguishable species of Diaporthales were identified. In adddition, 8 known species of Colletotrichum, C. fructicola, C. camelliae, C. aenigma, C. siamense, C. henanense, C. karstii, C. tropicicola, C. gigasporum, were identified. This study is the first to report C. tropicicola and C. gigasporum in tea plant in China. Discula theae-sinensis was the most common species in this study and caused disease lesions around wounded areas of tea leaves. The dual trials in vitro indicated Discula theae-sinensis and Colletotrichum were slight inhibition. Co-inoculating Discula theae-sinensis and C. fructicola was superior to single inoculation at low concentration.

As the global demand for clean and sustainable energy sources intensifies, hydrogen emerges as a promising alternative fuel. The widespread adoption of hydrogen, however, is impeded by the lack of efficient systems for storage and transportation. This review aims to summarize the recent advancements and prevailing challenges within the realm of hydrogen storage and transportation, thereby providing guidance and impetus for future research and practical applications in this domain. Through a systematic selection and analysis of the latest literature, this study highlights the strengths, limitations, and technological progress of various hydrogen storage methods, including compressed gaseous hydrogen, cryogenic liquid hydrogen, organic liquids hydrogen, solid materials hydrogen storage, as well as the feasibility, efficiency, and infrastructure requirements of different transportation modes such as pipelines, road and seaborne transportation. The findings reveal that challenges such as low storage density, high costs, and inadequate infrastructure persist despite progress in high-pressure storage and cryogenic liquefaction. The review also underscores the potential of emerging technologies and innovative concepts, including metal-organic frameworks, nanomaterials, and underground storage, along with the potential synergies with renewable energy integration and hydrogen production facilities. In conclusion, interdisciplinary collaboration, policy support, and ongoing research are essential in harnessing hydrogen’s full potential as a clean energy carrier. This review concludes that research in hydrogen storage and transportation is vital to global energy transformation and climate change mitigation.

Galangin(Gal) is a natural active flavonoid compound separated from the roots and rhizomes of Alpinia ofcinarum Hance. Modern pharmacological studies have shown that Gal has a variety of biological activities such as anti-tumor, anti-fungal, anti-bacterial, anti-inflammatory, anti-ischemic stroke, suppressing vitiligo and Alzheimer’s disease, etc. The purpose of this research was to prepare a galangin self-microemulsion drug delivery system (Gal-SMEDDS) and compare its anti-oxidant activity and pharmacokinetics with free Gal.The average particle size of the prepared Gal-SMEDDS was approximately 21.33 nm, the polydispersity index was 0.096, the zeta potential was -4.09 mV, and the entrapment efficiency was 96.74%. Compared with free Gal, the release of Gal-SMEDDS was improved in vitro release experiment. Cell experiments showed that Gal had obvious anti-oxidation effect, and the effect of Gal-SMEDDS was better than that of free Gal. In vivo pharmacokinetic experiments showed that the pharmacokinetic parameters of Gal-SMEDDS were better than that of free Gal, which indicated that the self-microemulsion drug delivery system(SMEDDS) effectively increases the oral bioavailability of Gal and alters its pharmacokinetic parameters, such that it may be effective in the treatment of anti-oxidant.

Trichinellosis is a major worldwide health concern caused by T. spiralis infection without highly efficient and safe therapeutic method so far. To solve the problem of uncomplete drug treatment schemes and the rise of anthelmintic resistance, a potential protective effect of probiotic strains against zoonotic T. spiralis infection was investigated in the framework of a new therapeutic strategy aimed at using probiotics to control parasitic zoonoses. The study was focused on L. reuteri protected against T. spiralis infection in intestinal phase throughout the detection of adult worm number, inflammatory factors mRNA expression, antioxidant enzyme expression and Nrf2 signal pathway protein expression. Mice were divided randomly into 3 groups: 1) Control group: no treatment; 2) Ts group: T. spiralis infection; 3）LAB group: T. spiralis infected after orally administered L. reuteri for 7 days. Probiotics bacteria were administered daily in a dose of 109 CFU/mL, and mice were infected with 400 T. spiralis larvae in the experimental groups. The number of adult worms was also significantly increased after administration of probiotics. Meanwhile, L. reuteri alleviate the inflammatory response caused by T. spiralis infection in intestinal has been confirmed. In addition, the promotion of antioxidant enzyme expression can be inferred that L. reuteri regulate Nrf2 signal pathways against T. spiralis infection. Our study demonstrates that L. reuteri provide protection against T. spiralis infection in intestinal. Therapeutic approaches with probiotic strains admission could help to reduce the risks of trichinellosis or complement classical anti-parasite treatments.

Battery/Supercapacitor(SC) current tracking control is a key issue for hybrid energy storage system (HESS) in electric vehicles. An innovative passivity-based L2-gain adaptive control (PBL2AC) based on port-controlled Hamiltonian model with dissipativity (PCHD) for reference current tracking and bus voltage stability in HESS is presented. The developed PCHD model has considered both parameter variations and external disturbances. By using L2-gain disturbance attenuation, the PBL2AC ensures robust reference current tracking and stable bus voltage. Moreover, adaptive mechanism is adopted to estimate the electrical parameters. To validate the proposed control scheme for HESS, simulations and experiments were done and compared with traditional PID and sliding mode control under several typical driving cycles, and results show that the effectiveness of the proposed controller can be confirmed.

As the COVID-19 pandemic has caused enormous damage to society, economy and public health security, it is crucial to combat the epidemic and allocate social and health resources effectively. Global optimization algorithms are extensively used in many domains to find optimal solutions to complex problems. Thus, a survey of three typical global optimizations applied on the COVID-19 pandemic is timely. This article is structured into three typical global optimization algorithms - Genetic Algorithm, Particle Swarm Optimization, and Cat Swarm Optimization - and summarizes the framework models and practical applications, as well as other optimization methods that may be applied to COVID-19. Finally, current unresolved challenges and future research opportunities to be explored are summarized.

Under the guidance of our previous achievements, and in order to extend this small molecular library. In current work, other 21 novel structures of thieno[2,3-d]pyrimidines containing isoxazole-moiety (1a-1u) were firstly synthesized and the cytotoxicity to A549, HCT116 and MCF-7 cell lines was evaluated using the MTT method. The results showed that most target compounds exhibited good to excellent cytotoxicity to A549, HCT116 and MCF-7 cell lines, especially 6-Methyl-4-{[3-(4-chlorophenyl)-isoxazol-5-yl-]-methoxy-}-thieno[2,3-d]-pyrimidine (1e) exhibited a broad-spectrum and the most potent cytotoxicity to A549, HCT116 and MCF-7 cell lines (IC50s: 2.79, 6.69 and 4.21×10^-3 μM, respectively) as compared with the reference drug gefitinib (IC50s: 17.90, 21.55 and 20.68 μM, respectively). 1e can be seen as the best drug candidates for development of anticancer drugs.

Trimeresurus albolabris, also known as the white-lipped pit viper or white-lipped tree viper, is a highly venomous snake distributed across Southeast Asia and the cause of many snakebite cases. In this study, we report the first whole genome assembly of T. albolabris obtained with next-generation sequencing from a specimen collected in Mengzi, Yunnan, China. After genome sequencing and assembly, the genome of this male T. albolabris individual was 1.51 Gb in length and included 38.42% repeat-element content. Using this genome, 21,695 genes were identified, and 99.17% of genes could be annotated using gene functional databases. Our genome assembly and annotation process was validated using a phylogenetic tree, which included six species and focused on single-copy genes of nuclear genomes. This research will contribute to future studies on Trimeresurus biology and the genetic basis of snake venom.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

In emergency situations, ensuring standardized Cardiopulmonary Resuscitation (CPR) actions is crucial. However, current Automated External Defibrillators (AEDs) lack methods to determine whether CPR actions are performed correctly, leading to inconsistent CPR quality. To address this issue, we introduce a novel method called Deep Learning-based CPR Action Standardization (DLCAS). This method involves three parts. First, it detects correct posture using OpenPose to recognize skeletal points. Second, it identifies a marker wristband with our CPR-Detection algorithm and measures compression depth, count and frequency using a depth algorithm. Finally, we optimize the algorithm for edge devices to enhance real-time processing speed. Extensive experiments on our custom dataset have shown that the CPR-Detection algorithm achieves a mAP0.5 of 97.04%, while reducing parameters to 0.20M and FLOPs to 132.15K. In a complete CPR operation procedure, the depth measurement solution achieves an accuracy of 90% with a margin of error less than 1 cm, while the count and frequency measurements achieve 98% accuracy with a margin of error less than 2 counts. Our method meets the real-time requirements in medical scenarios, and the processing speed on edge devices have increased from 8fps to 25fps.

With the global climate anomalies and the destruction of ecological balance, water shortage has become a serious ecological problem facing all mankind, and drought has become a key factor restricting the development of agricultural production. Therefore, it is essential to study the drought tolerance of crops. On the basis of previous studies, we reviewed the effects of drought stress on plant morphology and physiology, including the changes of external morphology and internal structure of root, stem and leaf, the effects of drought stress on osmotic regulation sub-stances, drought-induced proteins and active oxygen metabolism of plants. In this paper, the main drought stress signals and signal transduction pathways in plants are described, and the functional genes and regulatory genes related to drought stress are listed respectively. We summarize the above aspects in order to provide valuable background knowledge and theoret-ical basis for future agriculture and forestry breeding and cultivation.

Background: Coronavirus disease 2019 (COVID-19) is a new viral respiratory disease and whether pregnant women are at increased risk of infection is unknown. Viral pneumonia is an important indirect cause of maternal death. Little is known about the effects of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) during pregnancy. Objective: To describe the clinical characteristics of COVID-19 in pregnancy and their newborn infant, and we sought to explored whether the SARS-CoV-2 can be intrauterine vertically transmitted. Study Design: The study was a case series study conducted in the obstetric ward of Tongji Hospital affiliated to Huazhong University of science and technology, Wuhan, China. Demographic, clinical, laboratory and radiological profiles of the SARS-CoV-2 infection case series. A systematic testing procedure for SARS-CoV-2 infection using oropharyngeal swab, placenta tissue, vaginal mucus, and breast milk of mothers. and oropharyngeal swab, umbilical cord blood, and serum of newborns was conducted. Results: We have conducted the most thorough virological assessment to date, and we include a longer clinical observation in mother-infant dyads during hospitalization. The clinical course and outcomes of three pregnant women who acquired SARS-CoV-2 infection late pregnancy are described in mother-infant dyads. Two had caesarean delivery in their third trimester. All patients showed an uneventful perinatal course, and a successful outcome. No infants became infected by vertical transmission or during delivery. Conclusion: No evidence to suggest the potential risk of intrauterine vertical transmission in the case series and further in-depth study is needed. Both the pregnancy woman and infant showed fewer adverse maternal and neonatal outcomes.