Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

The process of preparing anti-glare thin films by spray-coating silica sol-gel to soda-lime glass was exclusively and statistically studied in this paper. The effects of sol-gel deliver pressure, air transport pressure, and spray gun displacement speed on the gloss, haze, arithmetic mean surface roughness, and total transmittance light were analyzed. The experimental results indicate that the factors of sol-gel deliver pressure, air transport pressure, and displacement speed exhibit significant effect on the haze, gloss, and Ra. In contrast, the variation of total transmittance light with these three factors are insignificant. Because the anti-glare property is predominantly determined by low gloss and high haze, therefore, we aim to minimize gloss and maximize haze to achieve high anti-glare. Central composite design and response rurface methodology are employed to analyze the main and interaction effects of the three factors through quadratic polynomial equations, which are confirmed by the analysis of variance and R². The response surface methodology predict the lowest gloss and highest haze are 9.2 GU and 57.0%, corresponding to the sol-gel deliver pressure, air-transport pressure, and displacement speed of 250 kPa, 560 kPa, and 140 mm/s, and 340 kPa, 620 kPa, and 20 mm/s, respectively. Comparing the predicted optimal data with the real experimental results validates the applicability of the mathematical model. This study provides an important basis for the subsequent production of anti-glare glass with different specifications to satisfy the market demand.

This study aimed at the investigation of the effect of substrate preheating on residual stress in laser powder bed fusion using a physics-based analytical model. In this study, an analytical model is proposed to predict the residual stress through the calculation of preheating affected temperature profile and thermal stress. The effect of preheating is super-positioned with initial temperature in the modeling of temperature profile using a moving heat source approach; the resultant temperature gradient is then employed to predict the thermal stress from a point body load approach. If the thermal stress exceeds the yield strength of the material, then the residual stress under cyclic heating and cooling will be calculated based on the incremental plasticity and kinematic hardening behavior of metal. IN718 is used as a material example to pursue this investigation. To validate the predicted residual stress, experimental measurements are conducted using X-ray diffraction on IN718 samples manufactured via laser powder bed fusion under different process conditions. Results showed that preheating of the substrate could reduce the residual stress in an additively manufactured part due to the reduction in temperature gradient and resultant shrinkage stresses. However, the excessive preheating could have an opposite impact on residual stress accumulation. Moreover, the results confirm that the proposed model is a valuable tool for the prediction of residual stress- eliminating the costly experiments and time-consuming finite element simulations.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

Antibiotic-loaded bone cement (ALBC) plays a pivotal role in infection prevention and treatment related to musculoskeletal surgery. The release efficacy of antibiotics from ALBC is closely tied to its surface area, yet little is known about the effective release depth. To investigate the relationship between surface area, volume, and antibiotic elution, spheric ALBC specimens with consistent outer diameters but different internal metal sphere diameters were prepared. Two vancomycin doses were utilized in ALBC specimens with an outer diameter of 35 mm: high (4 g) and low (1 g). Each dosage group included five specimens containing embedded metal spheres with diameters of 15, 25, 29, 32, or 33 mm. The resulting shell-like ALBC specimens had thicknesses of 10 mm, 5 mm, 3 mm, 1.5 mm, or 1 mm, respectively. The specimens were immersed in sterile phosphate buffer solution, and antibiotic elution was measured at designated sampling times (1, 3, 6, 10, 24, 48, 72, and 168 hours). Methylene blue was employed to visualize penetration depth. Vancomycin elution did not display statistically significant differences between high- and low-dose groups. In both groups, specimens with 1 mm thickness exhibited a higher vancomycin release efficiency (high-dose group: 18560±5474 μg, 6.7%; low-dose group: 2017±419 μg, 2.6%), decreasing sharply in thicker ALBC specimens. Methylene blue penetration depth showed no apparent difference between high-dose and low-dose groups. ALBC thickness does not significantly impact antibiotic elution, while surface area and antibiotic dose exert notable effects. These in vitro findings offer potential applications in clinical treatments for musculoskeletal infections.

In our previous study, a novel barrier processing on a porous low-dielectric constant (low-k) film was developed: an ultrathin Mn oxide on a nitrogen-stuffed porous carbon-doped organosilica film (p-SiOCH(N)) as a barrier of the Cu film was fabricated. To form a better barrier Mn₂O_3-xN film, an additional annealing at 450°C was implemented. In this study, the electrical characteristics and reliability of this integrated Cu/Mn₂O_3-xN/p-SiOCH(N)/Si structure is investigated. The proposed Cu/Mn₂O_3-xN/p-SiOCH(N)/Si capacitors exhibited poor dielectric breakdown characteristics in the as-fabricted stage, although, less degradation was found after thermal stress. Moreover, its time-dependence-dielectric-breakdown electric-field acceleration factor slightly increased after thermal stress, leading to a larger dielectric lifetime in a low electric-field as compared to other MIS capacitors. Furthermore, its Cu barrier ability under electrical or thermal stress was improved. As a consequent, the proposed Cu/Mn₂O_3-xN/p-SiCOH(N) scheme is a promising integrity for back-end-of-line interconnects.

Individual investors often struggle to predict stock prices due to the limitations imposed by the computational capacities of personal laptop Graphics Processing Units (GPUs) when running intensive deep learning models. This study proposes solving these GPU constraints by integrating deep learning models with technical analysis methods. This integration significantly reduces analysis time and equips individual investors with the ability to identify stocks that may yield potential gains or losses in an efficient manner. Thus, a comprehensive buy and sell algorithm, compatible with average laptop GPU performance, is introduced in the study. This algorithm offers a lightweight analysis method that emphasizes factors identified by technical analysis methods, thereby providing a more accessible and efficient approach for individual investors. To evaluate the efficacy of this approach, we analyzed the performance of eight deep learning models: LSTM (4 layers), CNN, BiLSTM (4 layers), CNN Attention, BiGRU CNN BiLSTM Attention, BiLSTM Attention CNN, CNN BiLSTM Attention, and CNN Attention BiLSTM. These models were used to predict stock prices for Samsung Electronics and Celltrion Healthcare. The CNN Attention BiLSTM model displayed superior performance among these models, with the lowest validation mean absolute error value. In addition, an experiment was conducted using WandB Sweep to determine the optimal hyperparameters for four individual hybrid models. These optimal parameters were then implemented in each model to validate their back-testing rate of return. The CNN Attention BiLSTM hybrid model emerged as the highest-performing model, achieving an approximate rate of return of 5 percent. Overall, this study offers valuable insights into the performance of various deep learning and hybrid models in predicting stock prices. These findings can assist individual investors in selecting appropriate models that align with their investment strategies, thereby increasing their likelihood of success in the stock market.

This study used the sol–gel method to synthesize a non-halogenated hyperbranched flame retardant containing nitrogen, phosphorus and silicon, HBNPSi, which was then added to a polyurethane (PU) matrix to form an organic–inorganic hybrid material. Using 29Si nuclear magnetic resonance, energy-dispersive X-ray spectroscopy of P- and Si-mapping, scanning electron microscopy, and X-ray photoelectron spectroscopy, this study determined the organic and inorganic dispersity, morphology, and flame retardance mechanism of the hybrid material. The condensation density of the hybrid material PU/HBNPSi was found to be 74.4%. High condensation density indicates a dense network structure of the material. The P- and Si-mapping showed that adding inorganic additives in quantities of either 20% or 40% results in homogeneous dispersion of the inorganic fillers in the polymer matrix without agglomeration, indicating that the organic and inorganic phases had excellent compatibility. In the burning test, adding HBNPSi to PU resulted in the material passing the UL-94 standard at the V2 level, unlike the pristine PU, which did not meet the standard. The results demonstrated that after non-halogenated flame retardant was added to PU, the material’s flammability and dripping were lower, thereby proving that flame retardants containing elements such as nitrogen, phosphorus, and silicon exert an excellent flame retardant synergistic effect.

As environmental regulations become stricter, weight- and cost-effective fiber-reinforced polymer com-posites are being considered as alternative materials in the automobile industry. Rapid impregnation of the resin into the reinforcing fibers is critical during liquid composite molding, and the optimization of resin impregnation is related to the cycle time and quality of the products. In this review, various resins capable of rapid impregnation, including thermoset and thermoplastic resins, are discussed for manu-facturing fiber-reinforced composites used in the automobile industry, along with their advantages and disadvantages. Finally, vital factors and perspectives for developing rapidly impregnated resin-based fiber-reinforced composites for automobile applications are discussed

Mulberry is an economically significant crop for the sericulture industry worldwide. Stresses such as drought exposure have a significant influence on plant survival. Metabolome directly reflects plant physiological status; thus, a way to assess this impact is to perform a global metabolomic analysis. This study investigated the effect of drought stress on mulberry Yu-711 metabolic balance using a liquid chromatography-mass spectrometry (LC-MS) based on an untargeted metabolomic approach. For this objective, Yu-711 leaves were subjected to two weeks of drought stress treatment and control without drought stress. Multivariate and univariate statistical analyses highlighted numerous differentially-accumulated metabolic elements as a function of time and treatment. Drought stress led to a more differentiated metabolites response than the control. We found that the levels of total lipids and galactolipids, and phospholipids (PC, PA, PE) were significantly altered, producing 48% of the total differentially expressed metabolites. Fatty acyls were the most abundant lipids expressed and decreased considerably by 73.6%. Prenol lipids class of lipids increased in drought leaves. Other classes of metabolites, including polyphenols( flavonoids and cinnamic acid), organic acid (amino acids), carbohydrates, benzenoids, and organoheterocyclic, all had a dynamic trend in response to the drought stress. However, their levels under drought stress generally decreased significantly compared to the control. These results provide an overview of the metabolic profile of the mulberry plant through differentially-accumulated compounds and provide a better understanding of global plant metabolic changes in defense mechanisms.

Abstract: NFinFET transistors with fin channel length 90nm and a planar MOSFET transistor with channel length 180nm and 90nm are presented with characteristic curves at various gate biases. A finalized algorithm with kink effects is effectively responsible for addressing the field effect transistors. The algorithm includes the modified conventional current-voltage formula and a nonlinear heat-associated kink solution which is simplified as a Gaussian form. Three parameters in modified model includes kN (related with channel width, channel length, and gate oxide capacitor, and proportional to the mobility of carriers)Vth(Threshold Voltage), and (the inverse of Early Voltage). Those parameters are determined to minimize the discrepancies between the measured data and the fitting values, but leave kinks located at around (VGS－Vth), which are deliberately eliminated by the Gaussian form because of the agitation of thermal kink effects. The whole fitting is made to be as close as the as-measured IDS-VDS. In the mean time, those determined parameters are physically meaningful after the analysis has been done.

The NCO functional group of 3-isocyanatoproply triethoxysilane (IPTS) and the OH functional group of DOPO-BQ were used to conduct an addition reaction. Following completion of the reaction, triglycidyl isocyanurate (TGIC) was introduced to conduct a ring-opening reaction. Subsequently, a sol-gel method was used to take place a hydrolysis- condensation reaction on TGIC-IPTS-DOPO-BQ to form a hyperbranched nitrogen–phosphorous–silicon (HBNPSi) flame retardant. This flame retardant was incorporated into a polyurethane (PU) matrix to prepare a hybrid material. Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), limiting oxygen index (LOI), UV-VIS spectrophotometry, and Raman analysis were conducted to structure characterization and analyzed transparency, thermal stability, flame retardancy, and residual char to understand the flame retardant mechanism of prepared hybrid materials. After the flame retardant was added, the maximum degradation rate decreased from −36 wt%/min to −17 wt%/min, the integral procedure decomposition temperature (IPDT) increased from 348 ℃ to 488 ℃, and the char yield increased from 0.7 to 8.1 wt%. The aforementioned results verified that thermal stability of PU can be improved after adding HBNPSi. The LOI analysis indicated that the pristine PU was flammable because the LOI of pristine PU was only 19. When the content of added HBNPSi was 40%, the LOI value was 26; thus the PU hybrid became nonflammable.

Based on the major, trace element, and isotope data of the Cenozoic basalts in the study area, it is indicated that the basalts in this region can be classified into three distinct magma systems: alka-li basalts, tholeiite basalts, and Nushan alkali basalts. The geochemical characteristics observed in the studied basalts indicate that the mantle source in this region might have experienced met-asomatic processes prior to partial melting, which could be linked to an ancient subduction pro-cess. Combining the geochemical characteristics in the studied basalts with previous research, we propose that the underlying mantle source in Anhui province may have undergone metaso-matism due to the carbonatitic melts. These melts are believed to have originated from car-bonated eclogite, derived from subducted Pacific slab materials present in the deeper mantle. According to the Sr-Nd isotope data, it is suggested that the mantle source in the Nushan region could be derived from a depleted asthenospheric mantle, while the basaltic composition in the Niugang area may be representative of the mantle's end components associated with the EM-I enriched mantle source present in this study area. Therefore, we propose that the Anhui basalts may have originated from the partial melting of a mantle source representing a mixing of two end-members: DMM (Depleted MORB Mantle) and EM-Ⅰ (Enriched Mantle 1). The Anhui basal-tic magmas may have originated from the partial melting of EM-Ⅰ, potentially influenced by upwelling asthenospheric mantle or asthenospheric diapirism processes. The mantle source in the study area experiences partial melting at 1-5%, 15%, and 1-10%, resulting in the formation of parent magmas for alkali basalt, tholeiitic basalt, and Nushan alkali basalt. Subsequently, the parent magmas experienced fractional crystallization processes, which included minerals like olivine, pyroxene, and plagioclase. This led to the formation of various types of basalt in the study area.

(1) Background: Ulcerative colitis (UC) is characterized by immune system dysregulation with frequent extraintestinal manifestations, including airways involvement. Reduction in CO diffusing capacity and functional alterations in small airways have been described. The extended analysis of Fractional Exhaled Nitric Oxide (FeNO), may distinguish the sites of production and the presence of small airways inflammation being a useful, non-invasive marker for these patient’s follow up. The aim of our study was to compare PFTs, FeNO and CANO values of UC patients with different clinical disease activity and healthy subjects to reveal lung function abnormalities and the presence of subclinical airway inflammation. (2) Methods: We enrolled 42 adult outpatients with different clinical activity stages of UC (mean age 39±13 years) and a healthy control group of 41 subjects (mean age 29±3 years). C-reactive protein (CRP) and FeNO values at different flows (50,100 and 200 ml/sec) were collected. All patients performed pulmonary function tests (PFT’s) with static volumes and diffusing capacity (DLCO). (3) Results: FENO, CANO and CRP values were significantly increased in UC patients when compared with controls (p=0.02 and p&lt;0.0001, respectively) and proportionally to the disease activity (FeNO class 3: 27.1 ppb vs class 1-2: 6.2 ppb; CANO values class 3: 8.1 ppb vs class 1-2: 2.0 ppb (p &lt; 0.0001). TLC and DLCO were significantly reduced in UC patients compared to controls (p=0.011 and p&lt;0.0001, respectively). (4) The results of this study show significant lung functional abnormalities in UC patients and suggest the presence of airway inflammation directly correlated with the disease activity suggesting an integrated approach in routine assessment.

Polydimethylsiloxane with hydroxy groups was functionalized to form functionalized polydimethylsiloxane, which subsequently underwent an addition reaction with isophorone diisocyanate to form the prepolymer. Next, 3-aminopropyltriethoxysilane (APTS) reacted with 3-glycidoxypropyltrimethoxysilane (GPTS) to produce bridged polysilsesquioxanes, and the sol–gel technology was employed to form hyperbranched polysiloxane nanoparticles with hydroxy groups, which was used as the additive. The hyperbranched polysiloxane and the prepolymer containing NCO functional groups then underwent an addition reaction to produce the hybrid materials. Fourier-transform infrared spectroscopy and 29Si nuclear magnetic resonance were used to characterize the structure of the polyurethane hybrid. Regarding thermal stability, after the hyperbranched polysiloxane nanoparticles was introduced, the integral procedural decomposition temperature increased from 348 ºC for polyurethane matrix to 859 ºC for the hybrid material. The results revealed that the thermal stability of the hybrid material substantially increased by approximately 247%.

Novel multifunctional fluorescent chemosensors composed of electrospun (ES) nanofibers with high sensitivity toward pH, mercury ions (Hg²⁺), and temperature were prepared from poly(N-Isopropylacrylamide-co-N-methylolacrylamide-co-rhodamine derivative) (poly(NIPAAm-co-NMA-co-RhBN2AM)) by employing electrospinning process. NIPAAm and NMA moieties provide hydrophilic and thermo-responsive properties (absorption of Hg²⁺ in aqueous solutions), and chemical cross-linking sites (stabilization of the fibrous structure in aqueous solutions), respectively. The fluorescent probe, RhBN2AM is highly sensitive toward pH and Hg²⁺. Synthesis of poly(NIPAAm-co-NMA-co-RhBN2AM) with different compositions were carried on via free-radical polymerization. ES nanofibers prepared from sensory copolymers with a 71.1:28.4:0.5 NIPAAm: NMA: RhBN2AM ratio (P3 ES nanofibers) exhibited significant color change from nonfluorescent to red fluorescence while sensing pH or Hg²⁺, and high reversibility of on/off switchable fluorescence emission when Hg²⁺ and ethylenediaminetetraacetic acid (EDTA) were sequentially added. The P3 ES nanofibrous membranes had a higher surface-to-volume ratio to enhance their performance than did the corresponding thin films. In addition, the fluorescence emission of P3 ES nanofibrous membranes exhibited second enhancement above the lower critical solution temperature. Thus, the ES nanofibrous membranes prepared from P3 with on/off switchable capacity and thermo-responsive characteristics can be used as multifunctional sensory devise for specific heavy transition metal (HTM) in aqueous solutions.

(1) Background: To identify the association between the presence or absence of raphe and aortic valve dysfunction as well as the presence of aortopathy in patients with bicuspid aortic valve (BAV); (2) Methods: This retrospective study enrolled 312 participants (mean [SD] age, 52.7 [14.3] years; 227 men [72.8%]) with BAV. The BAVs were divided into those with presence (raphe+) or absence (raphe-) of raphe. Valvular function was classified as normal, aortic regurgitation (AR), or aortic stenosis (AS) using TTE. The pattern of BAV aortopathy was determined by the presence of dilatation at the sinus of Valsalva and the middle ascending aorta using CCT.; (3) Results: BAVs with raphe+ had a higher prevalence of AR (148 [79.5%] vs. 48 [37.8%], P < .001) but a lower prevalence of AS (90 [48.6%] vs. 99 [78.0%], P < .001) compared with those with raphe-. The types of BAV aortopathy were significantly different (P = 0.021) according to those with BAV-raphe+ and BAV-raphe-.; (4) Conclusions: The presence of a raphe was significantly associated with a higher prevalence of AR but a lower prevalence of AS and combined dilatation of the aortic root and middle ascending aorta. The presence of raphe was an independent determinant of AR.

Accurate expression of bracket prescription is important for successful orthodontic treatment. The aim of this study was to evaluate the accuracy of digital scan images of brackets produced by four different intraoral scanners (IOSs) in terms of the height, position, and angle of the bracket slot when scanning the surface of dental model attached with bracket materials made from different composition of materials. Brackets made from stainless steel, polycrystalline alumina, composite and composite/stainless steel slot were considered, which have been scanned from 4 different IOSs (Primescan, Trios, CS3600 and i500). SEM images were used as references. Each bracket axis was set in the reference scan image, and the axis was set identically by superimposing with the IOS image, and then only the brackets were divided and analyzed. The difference between the manufacturer's nominal torque and bracket slot base angle was 0.39 in SEM, 1.96 in Primescan, 2.04 in Trios, and 5.21 in CS3600 (P <0.001). The parallelism, which is the difference between the upper and lower angles of the slot wall, was 0.55 in SEM, 7.55 in Primescan, 6.74 in Trios3, 6.59 in CS3600, and 24.95 in i500 (p <0.001). This study evaluated the accuracy of the bracket only and it must be admitted that there is some error in recognizing slots through scanning in general

Interstitial lung disease (ILD) is one of the most serious extra-articular complications of rheu-matoid arthritis (RA), which increases the mortality of RA. Because the pathogenesis of RA-ILD remains poorly understood, appropriate therapeutic strategies and biomarkers have not yet been identified. Thus, the goal of this review was to summarize and analyze the reported data on the etiology and pathogenesis of RA-ILD. The incidence of RA-ILD increases with age, and is also generally higher in men than in women and in patients with specific genetic variations and eth-nicity. Lifestyle factors associated with an increased risk of RA-ILD include smoking and exposure to pollutants. The presence of an anti-cyclic citrullinated peptide antibody, high RA disease activity, and rheumatoid factor positivity also increase the risk of RA-ILD. We also explored the roles of biological processes (e.g., fibroblast–myofibroblast transition, epithelial–mesenchymal transition, and immunological processes), signaling pathways (e.g., JAK/STAT and PI3K/Akt), and the his-topathology of RA involved in RA-ILD pathogenesis based on published preclinical and clinical models of RA-ILD in animal and human studies.

Background: Most drug-resistant Escherichia coli isolates in dogs come from diseased dogs. Prior to this study, the prevalence and risk factors of fecal carriage drug-resistant E. coli and epidemic clone sequence type (ST) 131 (including subtypes) isolates in dogs were unknown. Methods: Rectal swabs were used for E. coli isolation from 299 dogs in a veterinary teaching hospital in Taiwan. Antibiotic resistance and multiplex PCR analyses of E. coli for major STs were performed. Result: There were 43.1% cefazolin-resistant, 22.1% fluoroquinolone-resistant, and 9.4% extended-spectrum beta-lactamase-producing E. coli in our cohort. In the phylogenetic study, B2 was the predominant group (30.1%). The cefazolin-resistant group and ciprofloxacin-resistant group had greater antibiotic exposure in the last 14 days (P &lt; 0.05). The age, sex, and dietary habits of the antibiotic-resistant and -susceptible groups were similar. In the seven isolates of ST131 in fecal colonization, the most predominant subtypes were FimH41 and FimH22. Conclusion: Recent antibiotic exposure was related to the fecal carriage of antibiotic-resistant E. coli isolates. Three major subtypes (FimH41, H22, and H30) of ST131 can thus be found in fecal carriage in dogs in Taiwan.

In this paper, an extendable fuzzy robust speed controller suitable for induction motor drive system was proposed. Firstly, the two-degrees-of-freedom (2DOF) robust control technology with feedforward control and disturbance elimination method was adopted. Upon parameter variation and load disturbance, the motor drive system could utilize a robust controller to generate compensation signals and reduce the impact on controlling performance of the motor drive system. The magnitude of the compensation signal was adjusted via the weighting factor. However, should a fixed weighting factor be adopted, system instability might be generated easily when time delay and saturation of control force occur. Based on the above, the smart method of extendable fuzzy theory (EFT) was adopted in this paper to adjust adequate weighting factors, where the controlling performance of the induction motor drive system could be improved accordingly. The method divided the speed difference between motor speed command and actual speed of the induction motor, and the variation rate for such speed difference into 20 regional categories. The correlation degree between the speed difference of actual feedback, variation rate for speed difference and each regional category was then calculated, where more suitable weighting factor was selected. Therefore, the proposed extendable fuzzy robust 2DOF controller with variable weighting factor designed will allow better performance for response in speed tracking and load regulation. Lastly, the simulation software Matlab/Simulink was applied to simulate the utilization of the controlling method proposed for the induction motor drive system. For both the response in speed tracking and load regulation, the simulation results proved that the extendable fuzzy robust speed controller proposed provided better controlling performance than the conventional robust controller.

This paper proposes a compact planar Wi-Fi antenna with optimized radiation patterns for small uncrewed aerial vehicle (UAV) applications in both urban and open areas. It is suitable for mounting on the outermost side of the non-metallic wing of small UAVs. It has small dimensions of 16.5 mm (L) by 30.3 mm (W) by 1.6 mm (h), and the measured results of its prototype are in agreement with simulated data. Its impedance bandwidths over the two frequency ranges are 2.11 to 2.58 GHz and 5.06 to 7.5 GHz ( ). At 5.8 GHz, it has stronger radiation below the small UAV to reduce interference from rare-use directions. Its maximum radiations, the directions of the maximum radiation in each elevation plane, are below the UAV and between 14° and 29° from the horizontal plane. At 2.4 GHz, it has quasi-omnidirectional radiation to ensure a stable link in all directions, and its maximum radiations are near the horizontal plane. The optimized radiation patterns at 5.8 and 2.4 GHz can provide more antenna gain when the small UAV flies farther in urban and open areas, respectively. In addition, it has good vertically polarized radiation for long-distance applications.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

Candida glabrata is a yeast of increasing medical relevance, particularly in critically ill patients. It is the second most isolated Candida species associated with invasive candidiasis (IC) behind C. albicans. The attributed higher incidence is primarily due to an increase in the acquired immunodeficiency syndrome (AIDS) population, cancer, and diabetes patients. The elderly population and the frequent use of indwelling medical devices are also predisposing factors. The work aimed to review various virulence factors that facilitate the survival of pathogenic C. glabrata in IC. The available published research articles related to the pathogenicity of C. glabrata were retrieved and reviewed from four credible databases, mainly Google Scholar, ScienceDirect, PubMed, and Scopus. The articles highlighted many virulence factors associated with pathogenicity in C. glabrata, including adherence to a susceptible host surface, evading host defences, and producing hydrolytic enzymes (e.g., phospholipases, proteases, and haemolysins). The factors facilitate infection initiation. Other virulent factors include iron regulation and genetic mutations. Accordingly, biofilm production, tolerance to high-stress environments, and development of resistance to the antifungal drug, notably to fluconazole and other azole derivatives, were reported. The review provided evident pathogenic mechanisms and antifungal resistance associated with C. glabrata in ensuring its sustenance and survival.

Many corporations have now revised their value statements to showcase their commitment to sustainable development and green business due to the pressing issues of climate and environmental damage. Despite the importance of value statements that can direct companies to achieve sustainable goals, what kind of values can be perceived as organizational orientations to sustainability remains unknown. This study explores how the general public views the inclusion of sustainable components in value statements from the listed companies in Hong Kong by using Q-sort methodology (n = 30). Analyzing the final sample of 40 value statements extracted from 27 listed companies, we identified three factors related to sustainability, namely, Empowering business process management, Empowering customer-centric excellence, and Empowering sustainable progress. This study provides an additional component to the traditional triple bottom line by suggesting that internal operation of a company is an emerging idea to understand corporate sustainability.

Autonomous unmanned aerial vehicles (UAVs) require highly reliable navigation information. Generally, navigation systems with the inertial navigation system (INS) and global navigation satellite system (GNSS) have been widely used. However, the GNSS is vulnerable to jamming and spoofing. The terrain referenced navigation (TRN) technique can be used to solve this problem. In this study, to obtain reliable navigation information even if a GNSS is not available or the degree of terrain roughness is not determined, we propose a federated filter based INS/GNSS/TRN integrated navigation system. we also introduce a TRN system that combines batch processing and an auxiliary particle filter to ensure stable flight of UAVs even in a long-term GNSS-denied environment. As an altimeter sensor for the TRN system, we use an interferometric radar altimeter (IRA) to obtain reliable navigation accuracy in high altitude flight. In addition, a parallel computing technique with general-purpose computing on graphics processing units (GPGPU) is applied to process a high resolution terrain database and a nonlinear filter in real time on board. Finally, we verify the performance of the proposed system through software-in-the-loop (SIL) tests and captive flight tests in a GNSS unavailable environment.

Lung cancer remains one of the leading causes of cancer-related mortality worldwide. There is evidence of a complex interplay between lung cancer and interstitial lung disease (ILD), affecting disease progression, management strategies, and patient outcomes. Both conditions develop as the result of common risk factors such as smoking, environmental exposures, and genetic predispositions. The presence of ILD poses diagnostic and therapeutic challenges in lung cancer management, including difficulties in interpreting radiological findings, increased susceptibility to treatment-related toxicities, such as acute exacerbation of ILD after surgery and pneumonitis after radiation therapy and immunotherapy. Moreover, due to the lack of large, phase III randomized controlled trials in patients with lung cancer and ILDs, the evidence-based therapeutic options remain limited. The role of antifibrotic treatment in the prevention of lung-cancer-related treatment toxicities remains to be elucidated. Emerging diagnostic modalities and biomarkers, and optimizing personalized treatment strategies are essential to improve outcomes in this patient population.

Conventional cancer clinical trials can be time-consuming and expensive, often yielding results with limited applicability to real-world scenarios and presenting challenges for patient participation. Real-world data (RWD) studies offer a promising solution to address evidence gaps and provide essential information about the effects of cancer treatments in real-world settings. Defining RWD based on its original intent, which is the collection of data at the point of care for clinical purposes, can distinguish it from conventional clinical trial data. RWD can be generated using experimental designs that resemble those used in conventional clinical trials, but with several advantages, such as improved efficiency and a better balance between internal and external validity. RWD can support pharmacovigilance, insights into disease progression, and the development of external control groups. Prospective RWD collection enables evidence generation based on pragmatic clinical trials (PCTs) that support randomized study designs and expand clinical research to the point of care. To ensure the quality of real-world studies, it is crucial to implement auditable data abstraction methods and develop new incentives to capture clinically relevant data electronically at the point of care. The treatment landscape is constantly evolving, with the integration of front-line immune checkpoint inhibitors (ICIs), either alone or in combination with chemotherapy, affecting subsequent treatment lines. Real-world effectiveness and safety in underrepresented populations, such as the elderly, patients with poor performance status (PS), hepatitis, or human immunodeficiency virus-infected patients, are still largely unexplored. Similarly, the cost-effectiveness and sustainability of these innovative agents are important considerations in the real world.

Gastric inflammation-related disorders are commonly observed digestive system illnesses char-acterized by the activation of proinflammatory cytokines, particularly tumor necrosis factor-α (TNF-α). This results in the induction of cyclooxygenase-2 (COX-2)/prostaglandin E2 (PEG2) and matrix metallopeptidase-9 (MMP-9). These factors contribute to the pathogenesis of gastric in-flammation disorders. We examined the preventive effects of Lonicera japonica Thunb. ethanol ex-tract (Lj-EtOH) on gastric inflammation induced by TNF-α in normal GES-1 cells. The GES-1 cell line was used to establish a model that simulated the overexpression of COX-2/PGE2 and MMP-9 proteins induced by TNF-α, to examine the anti-inflammatory properties of Lj extracts. The re-sults indicated that Lj-EtOH exhibits significant inhibitory effects on COX-2/PEG2 and MMP-9 ac-tivity, attenuates cell migration, and provides protection against TNF-α-induced gastric inflam-mation. The protective effects of Lj-EtOH are associated with the modulation of COX-2/PEG2 and MMP-9 through activation of TNFR–ERK 1/2 signaling pathways as well as the involvement of c-Fos and nuclear factor kappa B (NF-κB) signaling pathways. Based on our findings, Lj-EtOH ex-hibits a preventive effect on human gastric epithelial cells. Consequently, it may represent a novel treatment for the management of gastric inflammation.

Small interfering RNA (siRNA) holds significant therapeutic potential by silencing target genes through RNA interference. Current clinical applications of siRNA have been primarily limited to liver diseases, while achievements in delivery methods are expanding its applications to various organs, including the lungs. Cholesterol-conjugated siRNA emerges as a promising delivery approach due to its low toxicity and high efficiency. This study focuses on developing a cholesterol-conjugated anti-Il6 siRNA and the evaluation of its potency for the potential treatment of inflammatory diseases using the example of acute lung injury (ALI). The biological activities of different Il6-targeted siRNAs containing chemical modifications were evaluated in J774 cells in vitro. The lead cholesterol-conjugated anti-Il6 siRNA after intranasal instillation demonstrated dose-dependent therapeutic effects in a mouse model of ALI induced by lipopolysaccharide (LPS). The treatment significantly reduced Il6 mRNA levels, inflammatory cell infiltration, and the severity of lung inflammation. IL6 silencing by cholesterol-conjugated siRNA proves to be a promising strategy for treating inflammatory diseases, with potential applications beyond the lungs.

Reinforcement Learning (RL) has demonstrated considerable potential in solving challenges across various domains, notably in autonomous driving. Nevertheless, implementing RL in autonomous driving comes with its own set of difficulties, such as the overestimation phenomenon, extensive learning time, and sparse reward problems. Although solutions like Hindsight Experience Replay (HER) have been proposed to alleviate these issues, the direct utilization of RL in autonomous vehicles remains constrained due to the intricate fusion of information and the possibility of system failures during the learning process. In this paper, we present a novel RL-based autonomous driving system technology that combines Obstacle Dependent Gaussian (ODG) RL, Soft Actor-Critic (SAC), and meta-learning algorithms. Our approach addresses key issues in RL, including the overestimation phenomenon and sparse reward problems, by incorporating prior knowledge derived from the ODG algorithm. We evaluated our proposed algorithm on official F1 circuits, using high-fidelity racing simulations with complex dynamics. The results demonstrate exceptional performance, with our method achieving up to 89% faster learning speed compared to existing algorithms in these environments.

Influenced by the quasi-stationary Mei-yu front and the development of mesoscale low vortices on the Mei-yu front, a torrential rain event occurred in Suzhou on July 6, 2020. The 24-hour rainfall recorded by the automatic station exceeded 200 millimeters, with the highest hourly intensity surpassing 70 millimeters, accompanied by thunderstorms and strong winds. This heavy precipitation process was characterized by suddenness, extremity, long duration, high precipitation efficiency, and backward propagation. Using various data sources such as the European ERA5 reanalysis data, ground-based automatic stations, sounding, Doppler weather radar, and wind profile radar, this paper analyzed in detail the circulation characteristics and radar echo structures of this torrential rain event, and further studied the triggering, feature evolution, and maintenance mechanisms of the heavy precipitation.The results show: (1) The continuously strengthening low-level jet stream propagates downward forming an ultra-low-level jet stream. Heavy precipitation is located on the left front side of the jet exit area, where strong convergence and lifting in the boundary layer overlap with the ascending branch of the secondary circulation above the shear line, resulting in heavy precipitation. (2) A supercell storm with intense precipitation produced this heavy rainfall event, characterized by a low centroid of strong echo; echo-free vault, bounded weak echo region, and other supercell structural features. During this event, the high reflectivity factor areas corresponded to high KDP value areas, indicating a large amount of liquid water content. Vertically, the KDP column can track the rainwater mixing ratio well, and its location corresponds to the vicinity of the short-term heavy precipitation occurrence. The high KDP value area mainly consists of numerous precipitation particles, and the vertical vortex wind field structure causes rapid growth of precipitation particles through continuous rolling. Furthermore, it can be found through correlation coefficients (CC) that there are always high-value areas for CC since they correspond to areas of intense precipitation. (3) Continuous triggering of mesoscale convective cloud clusters on the east-west ground convergence line leads to new development and forms a "train effect." Strong frontogenesis in both horizontal and vertical directions triggers and sustains this heavy precipitation event. The significant increase in liquid water and water vapor density has indicative significance for the occurrence of heavy precipitation.

Goal-conditioned reinforcement learning (RL) holds promise for addressing intricate control challenges by enabling agents to learn and execute desired skills through separate decision modules. However, the irregular occurrence of required skills poses a significant challenge to effective learning. In this paper, we demonstrate the detrimental effects of this imbalanced skill(sub-goal) distribution and propose a novel training approach, Classified Experience Replay (CER), designed to mitigate this challenge. We demonstrate that adapting our method to conventional RL methods significantly enhances the performance of the RL agent. Considering the challenges inherent in tasks such as driving, characterized by biased occurrences of required sub-goals, our study demonstrates the improvement in trained outcomes facilitated by the proposed method. In addition, we introduce a specialized framework tailored for self-driving tasks on highways, integrating Model Predictive Control (MPC) into our RL trajectory optimization training paradigm. Our approach, utilizing CER with the suggested framework, yields remarkable advancements in trajectory optimization for RL agents operating in highway environments.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

The domestic ducks (Anas platyrhynchos domesticus) are resistant to most of the highly pathogenic avian influenza virus (HPAIV) infections. In this study, we characterized the lung proteome and phosphoproteome of ducks infected with HPAI H5N1 virus (A/duck/India/02CA10/2011/Agartala) at 12 hr, 48 hr and 5 days post infection condition. Total 2082 proteins were differentially expressed and 320 phosphorylation sites mapping to 199 phosphopeptides corresponding to 129 proteins were identified. Functional annotation of proteome data analysis reveals activation of RIG-I-like receptor and Jak-STAT signaling pathways, that lead to induction of interferon stimulated genes (ISGs) expression. The pathway analysis of phosphoproteome datasets also confirms the activation of RIG I, Jak-STAT signaling, NF-kappa B signaling and MAPK signaling pathways in the lung tissues. The induction of ISGs proteins (STAT1, STAT3, STAT5B, STAT6, IFIT5 and PKR) establishes protective antiviral immune response in duck lung tissue. Further, the protein-protein interaction network analysis identified proteins like AKT1, STAT3, JAK2, RAC1, STAT1, PTPN11, RPS27A, NFKB1 and MAPK1 as main hub proteins that might play important roles in disease progression in ducks. Together, functional annotation of proteome and phosphoproteome datasets reveals the molecular basis of the disease progression and disease resistance mechanism in ducks infected with HPAI H5N1 virus.

A primary challenge facing conservationists is reconciling the human needs of forest adjacent communities with the needs of conserving forest biodiversity, especially in tropical regions with growing populations of rural poor. Agroforestry has the potential to simultaneously provide for human needs and enhance forest biodiversity, but the complex interactions and feedbacks between the social and natural dimensions are relatively undescribed and thus systematic implementation is rare. The attributes of trees on farms required for human needs and conservation value may conflict. For example, exotic species in monoculture may provide the most economic value for farmers, while relic or planted indigenous tree mixtures may be more valuable for biological conservation. The objective of this study was to explore whether agroforestry practices in a moist tropical forest ecosystem in Kenya can simultaneously provide timber and fuelwood value to small-holder farmers while extending forest tree biodiversity. We described the agroforestry attributes on farms around a tropical forest, assessed the relationship between number and biomass of timber/fuelwood trees and tree biodiversity, and explored the relationships between forest tree diversity attributes and farm tree diversity attributes on a landscape scale using spatial analysis. We found that the diversity and number of trees on farms in this area are extensive yet variable, but that no significant relationship exists between the number of timber/fuelwood trees and tree diversity. This suggests that the two values of agroforestry may not be in conflict, due mainly to the high diversity of trees used for fuelwood. We also found that trees on farms in the larger landscape add to the conservation value of forest tree biodiversity and could be important components in conservation management. If agroforestry is to play an increasingly active role in conserving biodiversity in human-dominated landscapes, particularly in areas of dense subsistence farmer populations, increase recognition needs to be given to farmer’s perception of the value of trees and their selection of what trees to plant or maintain.

This research develops the Osteoporosis Knowledge, Attitude, and Behaviors Questionnaire (OKABQ) with the intent to evaluate levels of osteoporosis knowledge, attitude and behavior change. The aims of the study were to develop and validate the OKABQ; and to establish a mediation model of the research. A quantitative, descriptive, and instrumental study was conducted in two phases: Phase I—development of the scale through Delphi Method by osteoporosis experts; Phase II—evaluation of the validity and reliability of the scale and construction of a mediation model using SmartPLS. In Phase I, the content validity index (CVI) of the questionnaire was higher than 0.96 and the inter-rater reliability (IRR) kappa was 1.00. In Phase II, exploratory factor analysis showed that two predominating factors of attitude as a mediation were addressed by the 26-item OKABQ. The indirect effect results from the estimated model indicates that attitude mediates the relationship between knowledge and behaviors (β = 0.114, t = 2.627, p < 0.001), which is positive and statistically significant. We concluded that the OKABQ is a valid measure of osteoporosis knowledge, attitude and behaviors for women with osteoporosis. These assessment results could assist healthcare providers in mitigating insufficiency on health education.

The enhancement of early diagnosis of lung cancer is mandatory to improve prognosis. We observed the increase cancer stem cells (CSC) and circulating tumor cells (CTC) in blood of mice on d3 after Lewis lung carcinoma (LLC) cell implantation before disease symptom. Besides we have developed an approach to reprogramming immune cells by inhibiting the MAPK/ERK pathway through MEKi and the PD-1/PD-L1 immune checkpoint signaling pathway. We hypothesized that reprogramming of spleen CD8+ T-cells could also create a population of immune cells with high antitumor activity. We reprogrammed CD8+ T-cells derived from the spleen of C57BL/6 mice (rsCD8+T-cells). The rsCD8+T-cells were able to migrate to lung and were more resistant after the exhaustion in vitro in comparison with naïve sCD8+T-cells. In the orthotopic LLC model, the rsCD8+T-cells therapy increased the amount of proliferating CD8+ and CD4+ T-cells in blood and lung from mice. The amount of CSC decreased in the blood and lung of mice treated with rsCD8+ T-cells. A morphological study revealed a decrease in the number of metastases in lung tissue. The antitumor effects of rsCD8+T-cells are based on the activation of the host immune response by increasing the populations of CD8+ and CD4+ T-cells and apoptosis of CSCs.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

Lung neuroendocrine tumors (LNETs) and gastroenteropancreatic neuroendocrine tumors (GEPNETs) are two distinct types of neuroendocrine tumors (NETs) that have traditionally been treated as a single entity despite originating from different sources. Although they share certain phenotypic characteristics and the expression of neuroendocrine markers, they exhibit differences in their microenvironment, molecular mutations, and responses to various therapeutic regimens. Recent research has explored the genetic alterations in these tumors, revealing dissimilarities in the frequently mutated genes, role of EGFR in carcinogenesis, presence of transcription factors, and immunogenicity of the tumor and its microenvironment. Spread Through Air Spaces (STAS), a phenomenon unique to lung carcinomas, appears to play a crucial role in LNET prognosis. These distinctions are also evident in the cascade response of lung and GI tract neuroendocrine tumors to somatostatin analogs, Peptide Receptor Radionuclide Therapy (PRRT), chemotherapy, and immunotherapy. Identifying similarities and differences between the two groups may im-prove our understanding of the underlying mechanisms and facilitate the development of more effective treatment strategies.

Background/Aim: microRNAs (miRNAs) are key regulators of both physiological and pathophysiological mechanisms in diabetes and gastrointestinal (GI) dysmotility. Our previous studies have demonstrated the therapeutic potential of miR-10a-5p mimic and miR-10b-5p mimic (miR-10a/b mimics) in rescuing diabetes and GI dysmotility in murine models of diabetes. In this study, we elucidated the safety profile of a long-term treatment with miR-10a/b mimics in diabetic mice. Methods: Male C57BL6 mice were fed a high-fat, high-sucrose diet (HFHSD) to induce diabetes and treated by five subcutaneous injections of miR-10a/b mimics for a 5-month period. We examined the long-term effect of the miRNA mimics on diabetes and GI dysmotility, including an assessment of cancer risk as well as liver and colon inflammation using cancer and inflammatory biomarkers. Results: HFHSD-induced diabetic mice subcutaneously injected with miR-10a/b mimics monthly for 5 months exhibited a marked reduction in fasting blood glucose levels with restoration of insulin and significant weight loss, improved glucose and insulin intolerance, and restored GI transit time. In addition, the miR-10a/b mimic treated diabetic mice showed no indication of risk for cancer development and inflammation induction in the liver, colon, and blood for the 5 months post injections. Conclusion: This longitudinal study demonstrates that miR-10a/b mimics, when subcutaneously administered in diabetic mice, effectively alleviate diabetes and GI dysmotility for 5 months with no discernible risk for cancer or inflammation in the liver and colon. The sustained efficacy and favorable safety profiles position miR-10a/b mimics as promising candidates in miRNA-based therapeutics for diabetes and GI dysmotility.

The aim of this study is to evaluate the optimal conditions of membrane filtration process. Both laboratory test and pilot-scale test were conducted to examine a treated water on blending water. The water sample were prepared by blending a raw water and the effluent water filtered through an organic membrane. The optimal efficiency in the treatment of water quality at the lab-scale test was generated under conditions of flux at 2.0 m³/m²∙day, the blending ratio of 4:1, and the optimal dosage of coagulant at 20 ppm. The pilot-scale test resulted in that the optimal efficiency was obtained under conditions of flux at 2.0 m³/m²∙day and the blending ratio of 6.0:1. However, the different results between lab-scale and pilot-scale tests on the optimal dosage of coagulant implied that it is difficult to achieve the stable condition of process operation at the low level of coagulant. In summary, the results indicated that, in the combination process of organic membrane and ceramic membrane, the recovery efficiency was achieved above the level of 98.4 %. Compared to 92.1 % in a single organic membrane process, the combination process is 6.3 % more efficient than the single one. This combination process of water treatment lead to stable recovery rates by the optimal input of dosage, less pollution load to water, and a stabilized filtration system.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

In this study, a composite flame retardant was created by combining fish scale (FS), fishery waste, and ammonium polyphosphate (APP), a commercially available flame retardant. The composite flame retardant was added to epoxy resin (EP) to form an EP/APP/FS composite that prevents burns and is environmentally friendly. The use of FS conforms to the concept of circular economy and lowers costs by reducing the consumption of APP. Thermogravimetric analysis (TGA), integral procedural decomposition temperature (IPDT), pyrolysis kinetics, limiting oxygen index (LOI), the Underwriters Laboratories 94 (UL94) flammability test, scanning election microscopy, Raman spectroscopy, and energy-dispersive X-ray spectroscopy were used to determine the thermal properties, flame retardant properties, flame retardant mechanism, char morphology, and composition of the composites. The TGA results indicated that the addition of 40% flame retardant raised the char residue from 16.45 wt% (pure EP) to 36.07 wt%, IPDT from 685.6 °C (pure EP) to 1143.1°C, LOI from 21% (pure EP) to 30%, and UL94 classification from fail (pure EP) to V-0. These results suggest an increase in char residue, which indicates better protection of the polymer matrix material. The improvements in IPDT, LOI, and UL94 classification, which indicate greater thermal stability, lower flammability (from flammable to fireproof), and higher flammability rating (from fail to V-0), respectively, suggest that the composite material has favorable thermal properties and is less inflammable.

Lung cancer is the leading cause of cancer related mortality worldwide. In order to improve its overall survival, early diagnosis is required. Since current screening methods still face some pitfalls, such as high false positive rates for low-dose computed tomography, researchers are still looking for early biomarkers to complement existing screening techniques in order to provide a safe, faster and more accurate diagnosis. Biomarkers are biological molecules found in body fluids, such as plasma, that can be used to diagnose a condition or disease. Metabolomics has already shown to be a powerful tool in the search for cancer biomarkers since cancer cells are characterised by impaired metabolism, resulting in an adapted plasma metabolite profile. The metabolite profile can be determined using nuclear magnetic resonance, or NMR. Although metabolomics and NMR metabolite profiling of blood plasma are still under investigation, there is already evidence for its potential for early-stage lung cancer diagnosis, therapy response, and follow-up monitoring. This review highlights some key breakthroughs in this research field, where the most significant biomarkers will be discussed in relation with their metabolic pathways and in light of the altered cancer metabolism.

Our image recognition system mainly judges whether the left upper limb in the image is the left upper limb or the right upper limb through our deep learning model in the image. The doctor then could give the correct surgical position. From the experimental results, it could be found that the precision rate and recall rate of the intelligent image recognition system proposed in this paper for preventing the upper limb dislocation surgery could reach 98% and 93%, respectively. It proved that our artificial intelligent image recognition system, AIIRS, could indeed assist orthopedic surgeons to prevent the occurrence of left and right dislocation in upper limb surgery. At the same time, this paper also completes the IRB application approval through the prototype experimental results and will conduct the second phase of human trials in the future. It showed that the research results of this paper will be of great benefit and research value to upper limb orthopedic surgery.

Our image recognition system mainly judges whether the left upper limb in the image is the left upper limb or the right upper limb through our deep learning model in the image. The doctor then could give the correct surgical position. From the experimental results, it could be found that the precision rate and recall rate of the intelligent image recognition system proposed in this paper for preventing the upper limb dislocation surgery could reach 98% and 93%, respectively. It proved that our intelligent image recognition system could indeed assist orthopedic surgeons to prevent the occurrence of left and right dislocation in upper limb surgery. At the same time, this paper also completes the IRB application approval through the prototype experimental results and will conduct the second phase of human trials in the future. It showed that the research results of this paper will be of great benefit and research value to upper limb orthopedic surgery.

In this study, we analyzed the microbial community of traditional fermented foods in Jeju Island to identify the distribution of useful microorganisms and confirm their anti-inflammatory and anti-melanogenic effects to determine their potential use as cosmetic ingredients. Firstly, we examined the microbial communities of Omphalius rusticus Jeotgal (OR), Spratelloides gracilis Jeotgal (SG), Chromis notata Jeotgal (CN), Turbo cornutus Jeotgal (TC), Trichiurus lepturus intestine Jeotgal (TL), Branchiostegus japonicus Sweet Rice Punch (BJ), Salted Anchovy Sauce (SA), Jeju Soy Sauce (JSS), and Jeju Soybean Paste (JSP). We found that Latilactobacillus sakei (87.2%), Tetragenococcus halophilus (37.7%), T. halophilus (96.8%), Bacillus subtilis (23.4%), T. halophilus (71.3%), L. sakei (53.7%), Lentibacillus sp. (42.9%), Enterococcus durans (14.6%), and E. durans (32.8%) were the dominant species. Secondly, to study the nine Jeju fermented foods’ anti-inflammatory and anti-melanogenic effects, we employed RAW 264.7 and B16F10 cells, classic cell models for inflammation and melanogenesis studies. Ethyl acetate extracts of the nine Jeju fermented foods all inhibited nitric oxide (NO) and melanin production in a concentration-dependent manner. Thirdly, to test the applicability of the nine Jeju fermented foods to human skin, we used the MTT assay to assess their cytotoxic effects on human keratinocytes (HaCaT cells). Finally, the topical applicability of the nine Jeju fermented foods was tested through primary skin irritation, and it was found that they did not cause any adverse effects. Therefore, extracts from the nine Jeju fermented foods have potential applications as ingredients in anti-inflammatory and anti-melanogenic products and can be used in the cosmetic industry.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

Mechanical ventilation (MV), used in patients with acute lung injury (ALI), induces diaphragmatic myofiber atrophy and contractile inactivity, termed ventilator-induced diaphragm dysfunction. Phosphoinositide 3-kinase- (PI3K-) is crucial in modulating fibrogenesis during the reparative phase of ALI; however, the mechanisms regulating the interactions among MV, myofiber fibrosis, and PI3K- remain unclear. We hypothesized MV with or without bleomycin treatment would increase diaphragm muscle fibrosis through the PI3K- pathway. Five days after receiving a single bolus of 0.075 units bleomycin intratracheally, C57BL/6 mice were exposed to 6 or 10 mL/kg MV for 8 h after receiving 5 mg/kg of AS605240 intraperitoneally. In wild-type mice, bleomycin exposure followed by MV 10 mL/kg prompted significant increases in disruptions of diaphragmatic myofibrillar organization, transforming growth factor-1, oxidative loads, Masson’s trichrome staining, extracellular collagen levels, positive staining of -smooth muscle actin, PI3K- expression, and myonuclear apoptosis (P &lt; 0.05). Decreased diaphragm contractility and peroxisome proliferator activated receptor- coactivator-1 levels were also observed (P &lt; 0.05). MV-augmented bleomycin-induced diaphragm fibrosis and myonuclear apoptosis were attenuated in PI3K-γ-deficient mice and through AS605240-induced inhibition of PI3K- activity (P &lt; 0.05). MV-augmented diaphragm fibrosis after bleomycin-induced ALI is partially mediated through PI3K-γ. Therapy targeting PI3K-γ may ameliorate MV-associated diaphragm fibrosis.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

Lung cancer remains the main cause of global cancer-related deaths. Currently low-dose computed tomography (LD-CT) shows a 20% reduction of mortality. However, its clinical suitability is hindered by cost, radiation, and some false positives. Thus, the discovery non-invasive and less-expensive biomarker is urgent needed. In this scenario, proteins released in biological fluids could be considered interesting biomarkers for their role in cancer development. We conducted a pioneering case-control pilot study aimed at assessing the usefulness of Raf Kinase Inhibitory Protein (RKIP) and its phosphorylated form (pRKIP) as potential early-stage lung cancer biomarkers. Urine and Blood samples of two consecutive and independent cohorts of lung cancer patients and healthy controls were screened by means of a novel experimental ELISA assay designed to evaluate both forms of the biomarker. Although urinary levels of RKIP were not statistically different between the lung cancer group and high-risk healthy group, serum ones instead increased significantly in early stage LC patients and permitted to discriminate LC patients from both low-risk (HS) and high-risk healthy subjects (HR-HS) with an overall 93% accuracy (AUC 0.93) when LC was compared to HS and 74% (AUC 0.73) when it was compared to high-risk group. Of note, the analysis of RKIP/pRKIP ratio also showed a high accuracy (90% - AUC 0.95) in discriminating LC patients from HS and more importantly, it allowed to identify LC patients compared to HR-HS, with a higher accuracy (79% - AUC 0.79) than RKIP alone. We hypothesize that serum RKIP levels may be correlated to the activation of the immune systems against the tumor during the first phases of its development. Our study identified a preliminary, non-invasive, RKIP and pRKIP profile able to discriminate with high specificity and sensitivity the early-stage lung cancer patients from high-risk Healthy Subjects. These results, although preliminary, suggest the utility of measuring RKIP/pRKIP as potential new screening test for lung cancer and provide the basis for future validation studies.

Energy and Environment Tax is used globally as a means of environment policy. Energy and Environment tax plays an important role as a driving force for the conversion to environmentally friendly energy. The basic tax principles considered in the design of energy and environmental taxation increases the efficiency of policy instruments. The purpose of this study is to evaluate South Korea’s energy and environmental taxation based on tax principles, namely, equity, efficiency, simplicity, flexibility, and accountability and to suggest directions for improvement. This study applied a methodology that provides policy implications, such as reviewing existing literature and comparing energy and environmental taxes. Results of this study show that South Korea’s energy and environmental taxation is negative in terms of equity, simplicity, and accountability. South Korea’s current energy and environmental tax is regressive to income classes and complex tax structures and it does not objectively measure the impact of energy and environmental taxation. However, energy and environmental taxation is evaluated positively in terms of efficiency and flexibility because it meets the greenhouse gas reduction policy and operates a flexible tax rate. The results of this analysis provide policy implications for reorganizing South Korea’s energy and environmental taxation

Limited knowledge is available about the association between autistic spectrum disorder (ASD) and precocious puberty. Our study examined the association between the two medical conditions, and the effect modification by sex and neuropsychiatric comorbidities in a nationwide population. To compare the risk of precocious puberty between ASD and non-ASD cases, we conducted Cox regression analysis, using ASD as exposure and time-to-precocious puberty as outcome. We adjusted for sex, attention-deficit/hyperactivity disorder (ADHD), tics disorder, obsessive–compulsive disorder (OCD), anxiety disorder, intellectual disability, and epilepsy. We performed a moderation analysis to examine the potential moderating effects by sex or comorbidities. Patients with ASD were prone to have precocious puberty, with an adjusted hazard ratio (aHR) of 1.80 (95% CI: 1.61-2.01). For the effect modification, sex, specifically females, moderated the association between ASD and precocious puberty, with relative excess risk due to interaction (RERI) 7.35 (95% CI 4.90-9.80). No significant effect modification was found for any of the comorbidities within the scope of additive effect modification. We found that patients with ASD were prone to precocious puberty, regardless of sex or comorbid neuropsychiatric disorders. Girls with ASD are at particularly higher risk to develop precocious puberty.

The study addresses the urgent environmental issue of climate change, focusing specifically on the role of local food, which is produced and consumed locally, helps reduce carbon emissions by eliminating the need for long-distance transportation. Through quantitative analysis, this study elucidates the potential benefits in environmental impact achieved through the consumption of local food: the significant reduction in carbon emissions. Specifically, the consumption of local food is found to yield an annual decrease of 2,421,296 tCO2 emissions, representing 2.5% of South Korea’s total greenhouse gas emissions from the transportation sector. This reduction further translates into an estimated economic value of USD 54.23 million (KRW 70.5 billion). This study underscores the potential of local food consumption as a tangible strategy to overcome environmental problems. Moreover, its academic contribution lies in its comprehensive analysis of the economic and empirical impacts of local food consumption on environment. Moving forward, we propose policies such as supporting local food distribution networks, providing public education on local food, fostering the local food industry, and providing incentives to revitalize local food consumption.

The object of this study was to discover an alternative therapeutic agent with fewer side effects against acne vulgaris, which is one of the most common skin diseases. Acne vulgaris often associates with acne-related bacteria such as <i>Propionibacterium acnes</i>, <i>Staphylococcus epidermidis</i>, <i>Staphylococcus aureus</i> and <i>Pseudomonas aeruginosa</i>, some of which exhibit a resistant against commercial antibiotics used in the treatment of acne vulgaris (tetracycline, erythromycin, and lincomycin). In the current study, we evaluated <i>in vitro</i> antibacterial activity of chitosan-phytochemical conjugates against acne-related bacteria. Three of chitosan-phytochemical conjugates used in this study showed stronger antibacterial activity than that of chitosan (unmodified control). Chitosan-caffeic acid conjugate (CCA) exhibited the highest antibacterial activity against acne-related bacteria with minimum inhibitory concentration values of 8 μg/mL to 256 μg/mL. In addition, the MICs of antibiotics against antibiotic resistant <i>P. acnes</i> and <i>P. aeruginosa</i> strains were dramatically reduced in the combination with CCA, suggesting that CCA would restore the antibacterial activity of the antibiotics. The analysis of fractional inhibitory concentration indices clearly revealed a synergistic antibacterial effect between CCA and the antibiotics. Thus, the median ∑FIC values against the antibiotic resistant bacterial strains were ranged from 0.375 to 0.533 in the combination mode of CCA and antibiotics.

Our results demonstrated that SWT stimulates osteoblastogenesis and increase the cell number of osteoblasts, suggesting positive regulatory effects on osteoblast differentiation. However, the effect of SWT on bone formation need further examination, since the expression of alp gene is downregulated. On the other hand, SWT appears to negatively regulate osteoclast differentiation and bone resorption, as number of osteoclasts and the expression of critical bone resorptive genes are all downregulated. Collectively, SWT might change the equilibrium of bone remodeling and increase the bone mass. Our data provided supportive evidences that this medicine formulation can be applied to treat osteoporosis or bone destructive diseases.

This study aimed to improve sensitivity of ferrous particle sensors used in various mechanical systems such as wind power gearboxes to detect abnormalities by measuring the amount of ferrous wear particles generated by metal-to-metal contact. Existing sensors collect ferrous particles using a permanent magnet. However, its ability to detect abnormalities is limited because it only measures amounts of ferrous particles collected on the top of the sensor. To overcome this limitation, this study evaluated sensibility of an existing sensor using a multi-physics analysis method and improved it by changing the core shape inside the sensor. The detection ability of the improved sensor was analytically shown to be better than the existing sensor. This study highlights the use of analytical methods and multi-physics analysis for developing a ferrous particle sensor and presents a method to compare sensibility analytically. Results of the improved sensor are expected to enhance the ability to detect abnormalities in the lubrication system where ferrous wear particles are generated. This study will contribute to the development of more effective ferrous particle sensors, which can potentially improve the performance and reliability of mechanical systems.

In this study, the literature on varnish contamination is investigated among the various con-taminations of lubricant. As the period of use of lubricant increases, the lubricant deteriorates and becomes contaminated. The varnish causes filter plugging, sticking of hydraulic valves and fuel injection pumps, obstruction of flow, reduction of clearance, poor heater and cooler perfor-mance, and increase of friction and wear in various lubrication systems. These problems also cause mechanical system failure, performance degradation, and increased maintenance and re-pair cost. To improve the problems causes by the varnish, an adequate understanding of varnish is required. Therefore, in this literature review, definitions and characteristics, generating ma-chinery, generating mechanisms, causes, measurement methods, and prevention or removal methods are summarized. Most of the data are reports of companies related to lubricant and machine maintenance, and are included in some papers. We hope that this summary of varnish will be helpful to those who are engaged in reducing or preventing varnish problems.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

Epoxy was blended with benzoxazine resin and aluminum trihydrate (ATH) additive to render flame retardancy while maintaining mechanical properties. The ATH was modified using three different silane coupling agents and then added to 60/40 epoxy/benzoxazine mixtures. The effect of blend compositions and surface modification on flame retardant and mechanical properties of the composites was investigated by UL94, tensile, and shear tests. Resin mixtures containing more than 40 wt% benzoxazine revealed a UL94 V-1 rating with enhanced tensile and shear strength. Upon addition of 20 wt% ATH to 60/40 epoxy/benzoxazine, a V-0 rating was achieved. The lowered tensile and adhesive properties of the composites in the presence of ATH were improved by modifying the ATH surface using silane coupling agents.

Hepatocellular carcinoma (HCC) is currently the third leading cause of malignancy-related mortalities worldwide. Natural killer (NK) cells are involved in the critical role of first line immunological defense against cancer development. Defects in NK cell functions are recognized as important mechanisms for immune evasion of tumor cells. NK cell function appears to be attenuated in HCC, and many previous reports suggested that NK cells play a critical role in controlling HCC, suggesting that boosting the activity of dysfunctional NK cells can enhance tumor cell killing. However, the detailed mechanisms of NK cell dysfunction in tumor microenvironment of HCC remain largely unknown. A better understanding of the mechanisms of NK cell dysfunction in HCC will help in the NK cell-mediated eradication of cancer cells and prolong patient survival. In this review, we describe the various mechanisms underlying NK cell dysfunction in HCC. Further, we summarize current advances in the approaches to enhance endogenous NK cell function and in adoptive NK cell therapies, to cure this difficult-to-treat cancer.

Background and Objectives: High rates of psychiatric disorders and comorbidities have been reported in juvenile detainees which have been associated with repeat offenses. However, research on this topic has been limited to Asian countries. This study aimed to examine the prevalence of psychiatric disorders and sexual differences among juvenile detainees in a detention center in South Korea. Materials and Method: The participants comprised 54 males and 46 females, with a minimum intelligence score of 80. Psychiatric diagnosis was determined using the Mini-International Neuropsychiatric Interview for Children and Adolescents (MINI-KID). The Massachusetts Youth Screening Instrument-Version 2 (MAYSI-2) was used to investigate gender differences. Results: Using the MINI-KID, the most frequent diseases were conduct disorder (CD), alcohol dependence, suicidal tendency, attention-deficit/hyperactivity disorder (ADHD) with statistically significant differences between men and women. Only alcohol abuse was higher in men while the rest were higher in women. The items with a statistically significant gender difference in MAYSI-2, were alcohol/drug use, feeling depressed/anxious, somatic complaints, suicidal ideation, and traumatic experience. All items for which the gender difference was statistically significant were higher in the proportion of women. Conclusions: Juvenile detainees exhibit high rates of psychiatric disorders and comorbidities. CDs, alcohol dependence and ADHD are the most common psychiatric disorders among juvenile detainees in South Korea. Assessment of and intervention in psychiatric disorders may help prevent further offenses. These findings highlight the importance of diagnosing and intervening in psychiatric disorders within juvenile detention systems.

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Nonsteroidal anti-inflammatory drugs (NSAIDs), which block the activity of cyclooxygenase (COX) isoenzymes and inhibit the synthesis of prostaglandin, have been used for pain relief. We have developed a method to separate a mixture of three NSAIDs, such as aspirin, paracetamol, and naproxen, using reverse-phase high-performance liquid chromatography (RP-HPLC). An isocratic mobile phase consisting of acidic water and acetonitrile was selected to run at a low flow rate, such as 0.8 mL/min. The mixture of three NSAIDs was injected at a low volume into a C18 column that was 150 mm in length and characterized using a UV detector at 230 nm. We identified three peaks in the chromatogram indicating the three compounds. The elution time of the peaks was less than 10 minutes. To identify multiple peaks on the isocratic flow using a short column, further studies are required regarding the proposed method to generate microfluidic devices for nanoLC.

Vascular endothelial growth factor (VEGF) is a important biomarker with significant clinical importance. It plays a key role in angiogenesis, would healing, tumor growth, lung development, and in retinal diseases. Hence, detecting and quantifying VEGF is crucial in clinical diagnosis and prognosis of various diseases. In this work, a simple but highly cost-effective platform is developed for VEGF protein detection by using commercially available interdigitated sensors that are modified through surface chemistry tagged with DNA aptamer grafting. The dielectric characteristics between the fingers of sensor is modulated by the negatively charged aptamer-VEGF capture and the impedance is estimated using impedance analyzer. Impedance spectra tests was compared between pristine unmodified, functionalized monolayer surfaces and aptamer-grafted surfaces in order to evaluate the efficacy of VEGF detection. In our results, the sensitivity experiments as conducted had shown the ability of the interdigitated sensor to detect VEGF at a low concentration of 5 pM. The specificity of the functionalized sensor in detecting VEGF is further studied by comparing the impedance to platelet-derived growth factor (PDGF), and the results confirm the specificity of the sensor. Finally, an alternative illustration of impedance spectra is also proposed to improve the data visualization, and such presentation may be potential for intelligent VEGF detection.

Dravet syndrome (DS), also known as severe myoclonic epilepsy of infancy, is a rare and drug-resistant form of developmental and epileptic encephalopathies, which is both debilitating and challenging to manage, typically arising during the first year of life, with seizures often triggered by fever, infections, or vaccinations. It is characterized by frequent and prolonged seizures, developmental delays, and various other neurological and behavioral impairments. Most cases result from pathogenic mutations in the sodium voltage-gated channel alpha subunit 1 (SCN1A) gene, which encodes a critical voltage-gated sodium channel subunit involved in neuronal excitability. Precision medicine offers significant potential for improving DS diagnosis and treatment. Early genetic testing enables timely and accurate diagnosis. Advances in our understanding of DS's underlying genetic mechanisms and neurobiology have enabled the development of targeted therapies, such as gene therapy, offering more effective and less invasive treatment options for patients with DS. Targeted and gene therapies provide hope for more effective and personalized treatments. However, research into novel approaches remains in its early stages, and their clinical application remains to be seen. This review addresses the current understanding of clinical DS features, genetic involvement in DS development, and outcomes of novel DS therapies.

This paper examines the moral community thesis in the secular context of China. Using multilevel logistic regression, we test (1) whether both individual- (measured by affiliation with institutional religion) and aggregate-level religiosity (measured by the number of religious sites per 10,000 people in province) are inversely related to law and rule violations at the individual level and (2) whether the province-level religiosity enhances the inverse relationship between individual religiosity and the deviant behaviors. Results from analyzing data from the 2010 China General Social Survey and the Spatial Explorer of Religions show that both individual- and aggregate-level religiosity are inversely related to the odds of violating the law and various rules of government, transportation, workplace, and other organizations. However, the cross-level interactions are not significant across models, indicating that the contextual religiosity does not increase the effect of individual-level religiosity on deviance. Implications of findings for the moral community thesis are discussed.

Background and Objectives: Although there has been growing interest in the association of ADHD with anxiety, depression, suicidal ideation, and self-esteem, there is a lack of consistent results and these associations remain unclear. This study investigated the differential patterns of anxiety, depression, suicidal ideation, and self-esteem with regard to the presence of ADHD. Materials and Methods: The subjects were divided into a patient group and a control group. The patient group included 49 patients diagnosed with ADHD at the department of psychiatry of one university hospital. For the control group, 3,727 students were invited to complete a questionnaire. Of the 1,717 students who responded to the questionnaire, 245 were selected for patient-controlled studies. All the subjects were instructed to complete the Beck Suicide Ideation Scale, Children's Depression Inventory, Beck’s Depression Inventory, State-Trait Anxiety Inventory, and Rosenberg Self-Esteem Scale. Results: ADHD subjects experienced more anxiety, depression, and suicidal ideation as well as lower self-esteem compared to the control group comprising participants without ADHD. Conclusions: These findings suggest that ADHD symptoms may contribute to greater suicidal ideation through experienced depression, anxiety, and low self-esteem in school-aged children. Therefore, appropriate ADHD symptom management is necessary to reduce suicidal ideation among school-aged children with ADHD symptoms.

Changes in coastal topography can affect the ecological environment and marine industries. In this study, we analyzed the patterns and causes of changes in shoreline and undersea topography in the Nakdong River estuary in the southeast of South Korea using depth and shoreline surveys of the estuary, as well as data on discharge, suspended sediments, and precipitation in the Nakdong River basin. The results showed that erosion and sedimentation occurred repeatedly owing to complex factors such as the discharge of the estuary and invasion by open sea waves. However, no clear unilateral trend was observed. Unlike previous survey data, a large amount of erosion occurred in the second half of 2020. Previously, sedimentation was the main process, but erosion occurred rapidly, which was observed in the summer of 2020 when the erosion was three times higher than that in other periods owing to the severe rainy season and torrential rains for over a month. In addition, regarding the flow rate and force of the river water outflow, the amount of discharge increased rapidly, causing erosion. Moreover, a strong typhoon in the summer of 2020 affected the topography of the estuary.

Osteoporosis is a common metabolic bone disease in patients with diabetes, which can develop simultane-ously with Type 2 diabetes (T2D) in postmenopausal women. Bisphosphonate (BP) is administered to pa-tients with both the conditions and may cause medication-related osteonecrosis of the jaws (MRONJ). It affects the differentiation and function of osteoclasts as well as thickness of cortical bone through bone mineralization. Therefore, this study aimed to investigate the effects of T2D on osteoclast differentiation and activity as well as cortical bone formation in postmenopausal patients with MRONJ. Tissue samples were collected from 10 patients diagnosed with T2D and Stage III MRONJ in the experimental group and from 10 patients without T2D in the control group. Histological examination was conducted, and expres-sion of dendritic cell-specific transmembrane protein (DC-STAMP) and tartrate resistant acid phosphatase (TRAP) was assessed. Cortical bone formation was analyzed using CBCT images. The number of TRAP-positive osteoclasts and DC-STAMP-positive mononuclear cells were significantly less in the experi-mental group (p < 0.05). Furthermore, the thickness and ratio of cortical bone were significantly greater in the experimental group (p < 0.05). In conclusion, T2D decreased the differentiation and function of osteo-clasts, and increased cortical bone formation in postmenopausal patients with MRONJ.

Despite the development of targeted therapeutics, immunotherapy, and strategies for early detection, lung cancer carries a high mortality. Further, significant racial disparities in outcomes exist for which the molecular drivers have yet to be fully elucidated. The growing field of Epitranscriptomics has introduced a new layer of complexity to the molecular pathogenesis of cancer. RNA modifications can occur in coding and non-coding RNAs, such as miRNAs, possibly altering their gene regulatory function. The potential role for such modifications as clinically informative biomarkers remains largely unknown. Here, we concurrently profiled canonical miRNAs, shifted isomiRs (templated and non-templated), miRNAs with single-point modification events (RNA and DNA) in White American (W) and Black or African American (B/AA) lung adenocarcinoma (LUAD) patients. We found that while most deregulated miRNA isoforms were similar in W and B/AA LUAD tissues compared to normal adjacent tissues, there was a subgroup of isoforms with deregulation according to race. We specifically investigated an edited miRNA, miR-151a-3p with an A-to-I editing event at position 3, to determine how its altered expression may be associated with activation of divergent biological pathways between W and B/AA LUAD patients. Finally, we identified distinct race-specific miRNA isoforms that correlated with prognosis for both Ws and B/AAs. Our results suggest that concurrently profiling canonical and non-canonical miRNAs may have potential as a strategy for identifying additional distinct biological pathways and biomarkers in lung cancer.

To understand lung damage caused by COVID-19, we deduced two-phase lung damage mechanisms. After the lungs are infected with SARS-CoV-2 virus, the affected lung tissue swells and surface properties of pulmonary capillaries change, resulting in an increased flow resistance of affected capillaries. If a sufficient number of capillaries are affected by the infection, the swelling and increased cell wall adhesion collectively raise pulmonary vascular resistance. The increased vascular resistance further increases the dwell times of WBCs in affected capillaries and nearly capillaries. When pulmonary pressure is sufficiently higher, WBCs are forced to squeeze into interstitial spaces or alveolar spaces when local pressures are higher than what the capillaries can withstand. When more and more WBCs are dynamically retained, the flow resistance of more capillaries rises, pulmonary vascular resistance rises, and pulmonary pressure rises. The rise in the pulmonary pressure in turn results in elevated capillary pressures. When capillary pressures around the alveoli are sufficiently high, they cause interstitial pressures to change from normally negative values to positive values. The positive pressures cause fluid leakage to the alveolar space and thus degrade lung function. Tissue swelling, and occupation of WBCs in interstitial spaces and alveolar spaces further reduce compressible volume, and thus cause further rise in the pulmonary vascular resistance and pulmonary pressure. When the pulmonary pressure has reached a critical point as in the second phase, the blood breaks capillary walls and squeezes through interstitial spaces to reach alveolar spaces, resulting in irreversible lung damages. The available free volume in the thorax cage, organ usable capacities, temperature and humid are expected to have great impacts on degree of lung damages. The free volume in the thorax cage, lung usable surplus capacity, and other organ usable capacities determine the arrival time of last-phase irreversible damage. The mechanisms imply that the top priority for protecting lungs is maintaining pulmonary micro-circulation and preserving organ functions in the entire disease course while controlling viral reproduction should be stressed in the earliest time possible. The mechanisms also explain leukecytes are recruited and migrated into inflamed tissues by increasing their dwell times caused by increased local flow resistance.

Background: Large-cell neuroendocrine carcinoma presents significant treatment challenges owing to its rarity and limited therapeutic options. The LANCE study was designed to explore the survival benefits of incorporating atezolizumab in chemotherapy for metastatic LCNEC. Methods: In this non-randomized study, patients with metastatic LCNEC were treated with ei-ther standard chemotherapy plus atezolizumab or standard chemotherapy alone. The primary outcomes measured were progression-free survival (PFS) and overall survival (OS), with an ex-ploratory analysis of miR375 in plasma as a potential biomarker. Results: Of the 22 screened patients, 17 met the inclusion criteria and were stratified into the atezolizumab and chemotherapy (n=10) or chemotherapy alone(n=7) groups. After a median follow-up of 23.3 months, the 12-month survival rate for the atezolizumab group was 57.1% (95% CI: 32.6%-100%) and 45.7% at 24 months (95% CI: 22.4%-93.2%). In contrast, the chemotherapy group had a 14.3% survival rate at both 12 and 24 months (95% CI: 2.33%-87.7%). The log-rank test for survival showed a statistically significant difference in the atezolizumab-treated group (chi-squared = 4, df = 1, p = 0.04). A non-significant correlation was found between disease pro-gression and elevated levels of miR375. Conclusions: This pilot study suggests that atezolizumab combined with chemotherapy may be effective in treating metastatic LCNEC. The non-significant correlation between plasma miR375 levels and disease progression suggests its biomarker potential, warranting further validation research.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

Lung cancer is the leading cause of cancer death worldwide therefore studies about the etiological factors and carcinogenesis are important.The aim of the study is to detect the presence and types of Human papilloma virus (HPV) in lung cancer and non-tumoral lung and Epidermal Growth Factor Receptor (EGFR) mutation prevalance in lung cancer with Polymerase Chain Reaction (PCR) method.Fifty patients who were histopathologically diagnosed lung cancer and 7 patients with non-neoplastic lung disease were enrolled in the study. HPV positivity was detected in 75.4% of the patients. The rate of high-risk HPV positivity was 100% in adenocarcinomas, 64.5% in squamous cell carcinomas, and 57% in non-neoplastic lung. HPV 51 was the most frequent type followed by HPV 16 (43.9%). There was no statistically significant relationship between HPV infection and age, gender and smoking history and EGFR mutation. The prevalence of HPV positivity is variable in lung cancer in different studies and this may be due to many factors including HPV detection methods, number of patients, geographic regions. New studies about the role of HPV infection need to be performed in order to obtain information about the use of prophylactic and theurepatic agents in lung cancer.

Cyclin-dependent kinase 4 and 6 (CDK4/6) inhibitors, including abemaciclib, have been approved for the treatment of hormone receptor-positive, HER2-negative advanced, and metastatic breast cancer. Despite the high therapeutic efficacy of CDK4/6 inhibitors, they are associated with various adverse effects, including potentially fatal interstitial lung disease. Therefore, a combination of CDK4/6 inhibitors with letrozole or fulvestrant has been attempted but has demonstrated limitations in reducing adverse effects, highlighting the need to develop new combination therapies. This study proposes a combination strategy using CDK4/6 inhibitors and tricyclic antidepressants to enhance the therapeutic outcomes of these inhibitors while reducing their side effects. The therapeutic efficacies of abemaciclib and desipramine were tested in different cancer cell lines (H460, MCF7, and HCT-116). The antitumor effects of the combined abemaciclib and desipramine treatment were evaluated in a xenograft colon tumor model. In vitro cell studies have showed the synergistic anticancer effects of combination therapy in the HCT-116 cell line. The combination treatment significantly reduced tumor size compared with control or single treatment without causing apparent toxicity to normal tissues. The combination of abemaciclib and desipramine may be a promising therapeutic strategy as they could reduce side effects and enhance tumor suppression.

This purpose of the study presented in this article is to comparing different service quality measurements between Kano and TRIZ that plays the critical roles in the catering industrial. Data collected from a DINESERV questionnaire comprises service-quality standards to increase customer satisfaction of mobile dining car. Finally, the TRIZ is standardized measure designed to improve the idealization of strategy for selecting the most appropriate service quality model. In addition, the preferences of more than one decision maker are internally aggregated into the TOPSIS procedure. All these things provide several important theoretical and practical implications for developing a successful mobile catering app.

This study investigates the effects of Zinc (4wt.%) and severe plastic deformation on the mechanical properties of AZ61 magnesium alloy through the stir-casting process. The severe plastic deformation (equal channel angular pressing (ECAP)) has been done followed by T4 heat treatment. The microstructural examinations revealed that the addition of 4wt.%Zn enhances the uniform distribution of β-phase, contributing to a more uniformly corroded surface in corrosive environments. Additionally, dynamic recrystallization (DRX) significantly reduces the grain size of as-cast alloys after undergoing ECAP. The attained mechanical properties demonstrate that after a single ECAP pass, AZ61 + 4wt.%Zn alloy exhibits optimal yield strength (YS), ultimate compression strength (UCS), and hardness. This research highlights the promising potential of AZ61 + 4wt.%Zn alloy for enhanced mechanical and corrosion-resistant properties, offering valuable insights for applications in diverse engineering fields.

U-Net, based on a deep convolutional neural network (CNN), has been clinically used to au-to-segment normal organs and potentially target volumes. However, CNNs with local geometric dependencies may limit the accuracy of segmentation. Additionally, the performance of CNNs can vary depending on the selection of network hyper-parameters, which was mitigated by the proposition of nnU-Net. We chose a vision transformer architecture called VT U-Net, which features a self-attention excluding the convolution layer, to overcome the limitations of CNNs by utilizing global geometric information of images. The VT U-Net v.2 became more powerful thanks to the adaptive hyper-parameter optimizer embedded in nnU-Net. However, despite leveraging the benefits of nnU-Net, VT U-Net v.2 still had additional network hyper-parameters that needed to be optimally chosen. Accordingly, among various hyper-parameters, this study attempted to find the optimal combination of the patch size and the embedded dimension regarding the transformer. From the 4-fold cross-validation, the modified VT U-Net v.2 showed the highest average performance for planning target volume (PTV) segmentation among the investigated networks. Though nnU-Net was based on convolution layers, the adaptive hyper-parameter optimizers turned out to enhance the performance. It was also confirmed that network hyper-parameters affected the segmentation accuracy of vision transformers.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Quadrotor drones have rapidly gained interest recently. Numerous studies are underway for the commercial use of autonomous drones, and especially the distribution businesses are taking serious reviews on drone delivery services. However, there are still many concerns about urban drone operations. The risk of failures and accidents makes it difficult to provide drone-based services in the real world with ease. There have been many studies that introduced supplementary methods to handle drone failures and emergencies. However, we discovered the limitation of the existing methods. The majority of approaches were improving PID-based control algorithms which is the dominant drone control method. This type of low-level approach lacks situation awareness and the ability to handle unexpected situations. This study introduces an event-based control methodology that takes a high-level diagnosing approach that can implement situation awareness via time-window. While leaving the low-level controller to involve in operating the drone for most of the time in normal situations, our controller operates at a higher level and detects unexpected behaviors and abnormal situations of the drone. We tested our method with real-time 3D computer simulation environments with Unreal Engine[15] and AirSim[31]. We were able to verify that our approach can provide enhanced double safety and better ensure safe drone operations. We hope our discovery to possibly contribute to the advance of real-world drone services in the near future.

The artificial intelligence (AI) is a machine or computing platform that is capable of making intelligent decision similarly to the human mind. The AI could improve diagnosis, treatment prognosis, and clinical workflow, particularly in the field of radiology. Concerning acute respiratory distress syndrome (ARDS) is a rather heterogeneous syndrome characterized by an inflammatory lung edema leading to an increased lung weight, decreased lung aeration with the presence of alveolar collapse and interstitial opacities mainly in the dependent area. Thus, lung imaging is an essential tool to assess not only the morphology but also the mechanical characteristics of ARDS patients. Chest computed tomography (CT) and ultrasound have a higher sensitivity and specificity than conventional chest radiography. This narrative review summarizes the state of art of AI in the field of lung imaging, focusing on CT and ultrasound technique in ARDS patients. A total number of 18 articles were retrieved. The application of AI in lung imaging was mainly devoted to assess the prediction of ARDS, the quantification of alveolar recruitment, the possible alternative diagnosis and the outcome. Although the presence of a physician is still essential to ensure a high quality of examinations the AI could assist the clinical team to provide the best possible care.

Diseases of the lung account for more than 5 million deaths worldwide and are a burden to healthcare. Improving clinical outcomes including mortality and quality of life involves a holistic understanding the etiopathogenesis, which can be provided by multi-omics integration of lung data. An enhanced understanding of large comprehensive datasets provides opportunities to mine those datasets for features that contribute to prevention and amelioration of disease. In this review, we evaluate lung disease models including animal models, organoids and single cell lines as mechanisms to study multiomics in lung health and disease. We provide examples of lung diseases where multi-omics investigations have provided a deeper insight into pathogenesis that has resulted in improved preventive and therapeutic interventions.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

Background and Objective: There is a paucity of literature comparing unilateral instrumented transforaminal lumbar interbody fusion (UITLIF) with bilateral instrumented TLIF (BITLIF) regarding radiological alignment, including the coronal balance, even though UITLIF might have asymmetric characteristics in the coronal plane. This retrospective study aimed to compare the clinical and long-term radiological outcomes of 1-level UITLIF and BITLIF in lumbar degenerative diseases (LDD). Materials and Methods: Patients who underwent 1-level UITLIF with two rectangular polyetheretherketone (PEEK) cages or BITLIF with ≥ 5 years of follow-up at a single hospital were included. We compared the clinical and radiological outcomes between the UITLIF and BITLIF. Results: In total, 63 and 111 patients who underwent UITLIF and BITLIF, respectively, were enrolled. The median follow-up was 85.55 months (range: 60–130). The UITLIF group had a significantly shorter operation time (185.0 [170.0–210.0] vs. 225.0 [200.0–265.0], p &lt; 0.001) and lower estimated blood loss (300.0 [250.0–500.0] vs. 550.0 [400.0–800.0], p &lt; 0.001) than BITLIF group. Regarding the clinical outcomes, there were no significant differences in the intermittent claudication score (p = 0.495) and Kirkaldy–Willis criteria (p = 0.707) at 1 year postoperatively. The interval changes of the local coronal Cobb angle at the index level, L1-S1 lordotic angle, and coronal off-balance from the immediate postoperative radiograph to the last follow-up were not significantly different (p = 0.687, p = 0.701, and p = 0.367, respectively). Conclusion: UITLIF with two rectangular PEEK cages is a viable option for providing comparable clinical outcomes and radiological longevity to BITLIF in 1-level LDD. In addition, UITLIF has advantages over BITLIF in terms of operative time and blood loss.

This study determines the threshold for the computational rate of actuator motor controllers for unmanned underwater vehicles necessary to accurately follow discontinuous square wave commands. Motors must track challenging square-wave inputs, and identification of key computational rates permit application of deterministic artificial intelligence (D.A.I.) to achieve tracking to a machine-precision degree of accuracy in direct comparison to other state-of-art approaches. All modeling approaches are validated in MATLAB simulations where the motor process is discretized at varying step-sizes (inversely proportional to computational rate). At a large step-size (fast computational rate), discrete D.A.I. shows a mean error more than three times larger than that of a ubiquitous model-following approach. Yet, at a smaller step size (slower computational rate), the mean error decreases by a factor of 10, only three percent larger than that of continuous D.A.I. Hence, the performance of discrete D.A.I. is critically affected by the sampling period for discretization of the system equations and computational rate. Discrete D.A.I. should be avoided when small step-size discretization is unavailable. In fact, continuous D.A.I. has surpassed all modeling approaches which makes it the safest and most viable solution to future commercial applications in unmanned underwater vehicles.

Neuronal cells are believed to rely on autophagy to maintain cellular homeostasis. Nevertheless, autophagy may be a therapeutic target for neurodegenerative diseases because of the role it plays in neuronal cell death. Despite Beclin 1 association with autophagy and apoptosis, the molecular mechanisms that underlie Tau-induced vesicular pathology and Tau protein aggregates in humans remain poorly understood. Here, we set out to examine the role of three genes-ATG14L, Beclin 1 and VPS34- in autophagy nucleation failure-associated Tau disorders in fruit fly models. We found that either reduced ATG14L levels improve neuronal outcomes, or transgenic expression of ATG6/Beclin 1 greatly reduced age-dependent neurodegeneration and Tau pathology; whereas, the loss of Beclin 1 exacerbated these effects. Prior to p-Tau accumulation, the neuronal Beclin 1 network is critical for reducing p-Tau accumulation, indicating that the loss of Beclin 1 causes Tau pathology and neurodegeneration. As neurodegeneration progressed, glial cells showed an upregulation of vesicular Beclin 1 immunoreactivities. The reduced VPS34 also resulted in p-Tau accumulation, suggesting that neurons require both Beclin 1 and VPS34 to reduce p-Tau accumulation. Our results provide mechanistic insight into the molecular pathways that cause age-dependent Tau pathology and neurodegeneration due to an excess of autophagy nucleation processes and autophagy activity, and we derive novel inferences on the therapeutic possibilities of rebalanced Beclin 1 network by reducing autophagic specific nucleation component of ATG14L.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

Emotion plays a powerful role in humans’ interaction with robots. In order to express more human-friendly emotions, robots need the capability of contextual appraisal that expresses the emotional relevance of various targets in the spatiotemporal situation. In this paper, an emotional appraisal methodology is proposed in this study to cope with such contexts. Specifically, the Ortony, Clore, and Collins model is abstracted and simplified to approximate an emotional appraisal model in the form of a sentence-based cognitive system. The contextual emotion appraisal is modeled by formulating the emotional relationships among multiple targets and the emotional transition with events and time passing. To verify the proposed robotic system’s feasibility, simulations were conducted for scenarios where it emotional interacts with humans manipulating liked or disliked objects on a table. This experiment demonstrated that the robot's emotion can variously change over time like human by using a proposed formula for emotional valence, which is moderated by emotion appraisal of occurring events.

Earth observation satellites can capture images of specific areas in Earth's orbit based on user requirements. Despite the high demand for satellite imagery, satellites remain a scarce resource. When there are many observation tasks that are large and dense, they may interfere with each other due to satellite mobility. To address this issue, a multi-satellite scheduling algorithm based on a task merging mechanism has been proposed. This paper proposes a two-stage approach to the problem: task merging phase and merging task scheduling phase. The task merging phase introduces two methods based on Mean Shift and Complete Graph to generate the merging task set. In the merging task scheduling phase, a multi-satellite scheduling algorithm based on merging tasks is employed to solve the problem. Finally, certain measurement experiments suggest the effectiveness of the algorithm.

The sexual reproduction of ascomycetes is controlled by the mating-type(MAT) locus. (Pseudo)homothallic reproduction has been hypothesized based on genetic data from Hirsutella sinensis (Genotype #1 of Ophiocordyceps sinensis). In this study, the differential occurrence of the mating-type genes in the MAT1-1 and MAT1-2 idiomorphs, which constitute the genetic control of O. sinensis reproduction, was analyzed in 237 strains and 5 genomes of H. sinensis. The mating-type genes were differentially transcribed in H. sinensis Strain L0106, and the MAT1-2-1 transcript in H. sinensis Strain 1229 was alternatively spliced, with an unspliced intron I containing stop codons; these findings constitute O. sinensis reproduction controls at the transcriptional and coupled transcriptional-translational levels. The occurrence of the mating-type genes and a-/α-pheromone receptor genes differed among the 5 H. sinensis genomes. The differential occurrence and transcription of these genes are inconsistent with self-fertilization under (pseudo)homothallism but suggest self-sterility of H. sinensis, which therefore needs a mating partner to achieve sexual outcrossing under heterothallism or hybridization. Consistent occurrence and transcription of the mating-type genes of both the MAT1-1 and MAT1-2 idiomorphs have been reported in natural and cultivated Cordyceps sinensis, but these findings are insufficient to determine the reproduction mode(s) because of the co-occurrence of >90 fungal species and multiple genomically independent genotypes of O. sinensis. The mutant MAT1-1-1 and α-pheromone receptor transcripts in natural C. sinensis result in the N-terminus or middle-truncated proteins, with changes in hydrophobicity and secondary structures of the proteins, suggesting heterogeneous fungal source(s) of the proteins and hybridization reproduction.

Purpose Radiotherapy is integral in the management of hematological malignancies (HM). Standard radiotherapy dose fractionation regimens range between 20-50 Gy in 10-25 fractions over 2-5 weeks. This study presents the outcomes of patients with HM treated with hypofractionation radiotherapy (HFRT) during the COVID-19 pandemic. Methods Patients (N=36) were treated with HFRT between January 2020 and September 2022. The outcomes measured were the overall response rate (ORR), freedom from local progression (FFLP), and overall survival (OS). Results Median follow-up was 13.2 months. Thirty-three patients (92%) had non-Hodgkin (NHL) or Hodgkin lymphoma (HL). Eighteen patients (50%) had aggressive and 9 (25%) had indolent NHL. Nineteen patients (53%) presented with stage I/II and 15(42%) with stage III/IV disease. Twenty-five (69.4%) and eleven (30%) received consolidative and definitive RT, respectively. Twenty patients (56%) received treatment to the neck and/or thorax, and 9 (25%) to the abdomen or pelvis. Total dose ranged from 18 to 42.5 Gy in 6-17 fractions/ 2.67-5 Gy per fraction. Median dose in 2 Gy fractions for an alpha/beta (α/β) ratio of 10 amounted to 39 Gy (SD ± 13.86), and 43.6 Gy (SD ± 12) for an α/β of 3. The most commonly used fractionation scheme was 39 Gy in 13 fractions. ORR was 94.4% for the entire cohort, and 100, 94.4, and 83.3% for indolent NHL, aggressive NHL, and HL patients. Two-year FFLP was 76% (95% CI: 34-93%) for the entire cohort, and 100, 87 (95%CI: 56.4-96.5%) and 42% (95% CI: 1.1-84.3%) for the indolent NHL, aggressive NHL, and HL patients. Two-year OS for the entire cohort was 80% (95% CI:59.9-90.5%), and 100, 66.1 (95% CI: 36.4-84.4%) and 100% for the indolent NHL, aggressive NHL, and HL patients. Only one patient presented with grade two pulmonary toxicity. Conclusion HFRT in HM provides excellent local control without any increase in toxicity.

ESG (Environmental, Social, and Governance) responsibility fulfillment increasingly affects enterprise valuation. Although researchers debate about the precise effects, the prevailing view suggests a linear relationship between ESG performance and enterprise value. This study introduces a novel ESG responsibility performance metric through the Regulated Intermediary Model to delve into this relationship within the Chinese context. Our findings reveal an inverted U-shaped relationship between ESG performance and enterprise value, with financing constraints having a significant moderating effect. These findings remain robust after employing instrumental variables to mitigate potential endogeneity. Heterogeneity analysis demonstrates that this inverted U-shaped relationship is particularly pronounced in non-polluting and non-state-owned enterprises. Moreover, a comparison between equity and debt financing mechanisms underscores that improved ESG performance is associated with lower cost of equity financing, thereby enhancing enterprise value. Financial institutions are encouraged to leverage innovative financial instruments to diversify enterprise financing channels and alleviate financing constraints of enterprises that fulfill their ESG responsibilities.

A machine learning method for classifying Lung UltraSound is here proposed to pro- vide a point of care tool for supporting a safe, fast and accurate diagnosis, that can also be useful during a pandemic like as SARS-CoV-2. Given the advantages (e.g. safety, rapidity, portability, cost-effectiveness) provided by the ultrasound technology over other methods (e.g. X-ray, computer tomography, magnetic resonance imaging), our method was validated on the largest LUS public dataset. Focusing on both accuracy and efficiency, our solution is based on an efficient adaptive ensembling of two EfficientNet-b0 models reaching 100% of accuracy, which, to our knowledge, outperforms the previous state-of-the-art. The complexity of this solution keeps the number of parameters in the same order as an EfficientNet-b0 by adopting specific design choices that are adaptive ensembling with a combination layer, ensembling performed on the deep features, minimal ensemble only two weak models. Moreover, a visual analysis of the saliency maps on sample images of all the classes of the dataset reveals where the focus is on an inaccurate weak model versus an accurate model.

Concussion, also known as mild traumatic brain injury (mTBI), commonly causes transient neurocognitive symptoms, but in some cases, it causes cognitive impairment, including working memory (WM) deficit, which can be long-lasting and impede a patient’s return to work. The predictors of long-term cognitive outcomes following mTBI remain unclear because abnormality is often absent in structural imaging findings. The purpose of the study was to determine whether machine learning-based models using functional magnetic resonance imaging (fMRI) biomarkers and demographic or neuropsychological measures at baseline could effectively predict 1-year cognitive outcomes of concussion. We conducted a prospective, observational study of patients with mTBI who were compared with demographically-matched healthy controls enrolled between September 2015 to August 2020. Baseline assessments were collected within the first week of injury, and follow-ups were conducted at 6 weeks, 3 months, 6 months, and 1 year. Potential demographic, neuropsychological, and fMRI features were selected according to the significance of correlation with the estimated changes in WM ability. The support vector machine classifier was trained using these potential features and estimated changes in WM between the predefined time periods. Patients demonstrated significant cognitive recovery at the third month, followed by worsened performance after 6 months, which persisted until 1 year after concussion. Approximately half of the patients experienced prolonged cognitive impairment at 1-year follow up. Satisfactory predictions were achieved for patients whose WM function did not recover at 3 months (accuracy=87.5%), 6 months (accuracy=83.3%), 1 year (accuracy=83.3%), and performed worse at 1-year follow-up compared to baseline assessment (accuracy=83.3%). This study demonstrated the feasibility of personalized prediction for long-term postconcussive WM outcomes based on baseline fMRI and demographic features, opening a new avenue for early rehabilitation intervention in selected individuals with possible poor long-term cognitive outcomes.

Activities in the digital economy driven by information technology have rapidly increased in scope and speed in the aftermath of COVID-19. Meanwhile, social isolation accelerated by quarantine measures has increased concerns about individuals’ mental health. However, little is known about the specific consequences of online interactions, especially when applied in online fan community-based relationships where loyal community members are prevalent. Therefore, we examined whether a sense of virtual community (SOVC) can link fans’ online activities with their mental well-being and behavioral loyalty to the platform. For this purpose, we focus on BTS fandom “Adorable Representative MC for Youth” (ARMY) behaviors and attitudes on the fan community platform Weverse. With 202 valid data samples acquired from global ARMY, this study conducted a partial least squares–structural equation modeling analysis. The empirical findings reveal that SOVC in Weverse is significantly influenced by the intensity of online interactions with other fans and parasocial relationships with celebrities. SOVC is found to be the direct predictor of fans’ behavioral loyalty and mental well-being. When considering fans’ perceptions of other social media platforms, dissatisfaction with previous online fan communities enhances the intensity of online interactions with other fans in Weverse.

(1) Background: The CEO message of hospital homepage contain various contents such as the hospital's future vision, promises with customers, upgraded services and public activities. The CEO’s message of the homepage includes non-financial information as well as financial information of corporates. Also, it provides useful information for not only company's goals and vision but also firm performance and strategies for the future. This study aims to investigate associations between CEO’s message of hospitals homepages and financial status. We used the balanced scorecard frame to analyze what content on the hospital's homepage is related to the hospital's various financial ratios. (2) Methods: We adopt a text mining method to extract significantly repeated keywords from the CEO’s message of hospital website. And we classify these keywords by a balanced scorecard frame. To examine the relationship between keywords of CEO’s message of the hospital homepage and hospital’s financial ratio, T-test is conducted for the difference in the TF-IDF (Term Frequency is Divided by Inverse Document Frequency) mean of the home page contents and its relationship with the views of the balanced scorecard framework. (3) Results: According to empirical results on 65 samples collected from local hospitals, there are some significant relationship between the qualitative content of the hospital's homepage and the quantitative financial ratio that indicates profitability, activity, leverage, liquidity, and transfer to essential business fund (EBF) income. (4) Conclusions: The introduction section of a homepage is most accessible to customers, containing the aims and ideals of hospitals and reflecting their values and visions [1]. In addition, in view of financial status, they can either emphasize financial strength or focus on other areas to mask weakness of financial information. This study reminds us of the importance of hospital website’s disclosure, and it can be inferred from the financial status of the hospital. It also highlights the need for harmonization between quantitative data, financial statements, and qualitative data, CEO’s messages. (5) Implications: To our best knowledge, this paper is the first research attempting to investigate the relation between text of hospital homepage and financial ratio of hospital through text mining technique and balanced scorecard frame. Hospitals take a crucial part in a country’s welfare and healthcare backbone industry. Nevertheless, in many countries, hospital organization sectors tend to remain a source of critical fiscal deficits due to its ineffective and sloppy management. We expect that the result of this paper can provide hospital managers to useful information.

In this study, a new empirical equation was established to predict the sedimentation volume resulting from the construction of a multipurpose weir or low-head dam. The study employed a one-dimensional numerical model (STAFF) to investigate the key parameters affecting sedimentation volume. Short-term predictions were conducted through laboratory experiments with movable bed, and the results indicated that dimensionless unit stream power and the Shields parameter exhibited the most significant correlation with dimensionless deposition volume. Using a multiple regression approach, an empirical equation was formulated and validated for predicting sedimentation in the upstream reservoir of the weir.

Gain-scheduled autopilots have emerged as a dominant strategy to achieve adaptive control of coupled, non-linear engineering complexities, owing to an ability to adapt to changing operational conditions and uncertainties. This study focuses on utilizing bilinear interpolation of gain-scheduled autopilots, emphasizing enhanced system performance and robustness. Through a comprehensive investigation and comparative analysis using three disparate cases, advantages over conventional methods are revealed. Strengths and weaknesses of both simple and specialized variants (such as linear, and real-time gain-scheduling) are introduced. Three missile guidance case–studies utilize simulation time and miss distance figures of merit. Potential to achieve precise control across various mission scenarios, while ensuring reduced computational complexity is revealed by nearly two–hundred percent improved missile miss distances with comparable distances traveled and slightly improved computational burden.