It has been more than a century since Erlang published his paper in 1909. The classical queueing system for the M/D/c queue has been investigated by many authors. The key is to find the roots of an equation using explicit or numerical methods. We present an alternate form of explicit solution(s) of this/these root(s) using the Lambert-W function in this paper. In addition, the unsaturated probabilities of the number of customers in the system is derived explicitly in terms of this/these root(s). Finally, the mean number of customers in the system and the mean queueing delay are obtained from these probabilities. The exact queueing delay formula for the M/D/c queue is expressed in closed-form in terms of the root(s). Numerical results show that they are in excellent agreement with the numerical results published by Seelen, Tijms and Van Hoorn.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

Clarifying the impact mechanism of digital transformation of enterprises on the M&A efficiency of listed companies can provide a factual basis for improving capital market regulatory policies. Taking the mergers and acquisitions of listed companies from 2007 to 2021 as a research sample, the influence mechanism of the digital transformation degree of companies on their M&A efficiency was studied. The research results show that the digital transformation of listed companies will improve their M&A efficiency. Digital transformation will reduce the degree of mispricing of stocks of M&A companies, curb conflicts between managers and agents of M&A companies, and improve their M&A efficiency. Further research finds that the promotion effect of digital transformation on M&A efficiency is more significant in non-state-owned companies, with a higher degree of financing constraint and high analyst attention. In the future, regulatory authorities should actively promote the digital transformation of listed companies, curb mispricing and management agency problems in the capital market with digital governance, and improve the efficiency of mergers and acquisitions in the capital market.

This paper first discusses a fractional-order Liu system of order as low as 2.7 and shows its chaotic characteristics by carrying out numerical simulations such as Lyapunov exponents, bifurcation diagrams and phase portraits. Then, by using the topological horseshoe theory and computer-assisted proof, the existence of chaos in the system is verified theoretically. Finally, the fractional-order system is implemented on a Field Programmable Gate Array (FPGA) and the results obtained show that the fractional-order Liu system is indeed chaotic.

Titania is one of the most comprehensively studied nanostructures due to its widespread applications in production of catalytic, gas- sensing and corrosion- resistance materials [1]. M-polynomial of nanotubes has been vastly investigated as it produces many degree-based topological indices which are numerical parameters capturing structural and chemical properties. These indices are used in the development of quantitative structure-activity relationships (QSARs) in which the biological activity and other properties of molecules are correlated with their structure like boiling point, stability, strain energy etc of chemical compounds. In this paper, we determine M-polynomials of single-walled titanium (SW TiO2) nanotubes and recover important topological degree based indices of them to theoretically judge these nanotubes. We also use Maple to plot surfaces associated to different types of single-walled titanium (SW TiO2) nanotubes.

In this paper, chaos sequence is used to replace the traditional Spread Spectrum sequence. From the perspective of the communication partner, a new method of generating the initial value of chaotic sequence is proposed, which is more suitable for the multi-base Spread Spectrum System and easy to extract. In order to further improve the error performance of the system and ensure the integrity of the system, an improved suboptimal soft information extraction method based on log-likelihood ratio (LLR) is proposed in the channel coding module, which can further improve the error performance of the system. On this basis, we choose the synchronization mode of multiple transmission of one reference signal to solve the problem that chaotic sequence is difficult to obtain synchronization because of its aperiodic characteristics. Finally, the system is simulated in the channel with low SNR. The simulation results show that chaotic sequence as Spread Spectrum code can make the signal transmit accurately in the worse channel environment. The performance gain of applying soft information decoding decision in the M-ary Spread Spectrum System with chaotic sequence as Spread Spectrum code can reach 5.2dB compared with the traditional Direct Spread Spectrum System.

This paper investigates the search for an exact analytic solution to a temporal first-order differential equation that represents the number of customers in a non-stationary or time-varying

Purpose. Moraxella is an ocular bacterial pathogen isolated in cases of keratitis, conjunctivitis, and endophthalmitis. Gram-negative brick-shaped diplobacilli from ocular specimens, and slow growth in culture, are early indications of Moraxella ocular infection; however, identifying Moraxella to species can be complex and inconsistent. Methods. In this study, bacteria consistent with Moraxella were identified to species using: 1) DNA sequencing coupled with vancomycin susceptibility, 2) MALDI-TOF Mass Spectrometry, and 3) Biolog ID System. Study samples consisted of 9 ATCC Moraxella controls, 82 isolates from keratitis, 21 isolates from conjunctivitis, and 4 isolates from endophthalmitis. Results. The ATCC controls were correctly identified. For keratitis, 66 (80.5%) were identified as M. nonliquefaciens, 7 (9.0%) as M. lacunata, 5 (6%) as M. osloensis, 2 (2.5%) as Acinetobacter lwoffi, 1 (1.0%) as M. bovis/nonliquefaciens, and 1 (1.0%) as M. osloensis/nonliquefaciens. For conjunctivitis, 9 (43.0%) were identified as M. osloensis, 6 (29.0%) as M. nonliquefaciens, 3 (14.3%) as Roseomonas, 2 (9.5%) as Acinetobacter (parvus, junii), and 1 (4.5%) as M. catarrhalis/M. nonliquefaciens. From endophthalmitis, 3 of 4 of the isolates were M. nonliquefaciens. Overall, M. nonliquefaciens and M. osloensis were identified in 70% (75 of 107) and 13% (14 of 107) of cases, respectively, totaling 83% (89 of 107). Conclusions. M. nonliquefaciens and M. osloensis are important bacterial pathogens of the eye as determined by DNA sequencing, MALDI-TOF MS, and Biolog. Although Moraxella catarrhalis is a clinical pathogen, other species of Moraxella appear to have a prominent role in eye infections.

Cells respond to DNA double-strand breaks by initiating DSB repair and ensuing a cell cycle checkpoint. The primary responder to DSB repair is non-homologous end joining, an error prone repair pathway. However, when DSBs are generated after DNA replication in the G2 phase of the cell cycle, a second DSB repair pathway, homologous recombination, can come into action. Both ATM and ATR are important for DSB-induced DSB repair and checkpoint responses. One method of ATM and ATR working together is through the DNA end-resection of DSBs. As a readout and marker of DNA end-resection, RPA is phosphorylated at Ser4/Ser8 of the N-terminus of RPA32 in response to DSBs. Here, the significance of RPA32 Ser4/Ser8 phosphorylation in response to DNA damage, specifically in S phase to G2 phase of the cell cycle is examined. RPA32 Ser4/Ser8 phosphorylation in G2 synchronized cells is necessary for increases in TopBP1 and Rad9 accumulation on chromatin and full activation of the ATR-dependent G2 checkpoint. In addition, our data suggest RPA Ser4/Ser8 phosphorylation modulates ATM-dependent KAP-1 phosphorylation and Rad51 chromatin loading in G2 cells.

Endothall dipotassium salt and monoamine salt are herbicide formulations used for controlling submerged aquatic macrophytes and algae in aquatic ecosystems. Microbial activity is the primary degradation pathway for endothall. To better understand what influences endothall degradation, we conducted a mesocosm experiment to 1) evaluate the effects of different water and sediment sources on degradation, and 2) determine if degradation was faster in the presence of a microbial community previously exposed to endothall. Endothall residues were determined with LC-MS at intervals to 21 days after endothall application. Two endothall isomers were detected. Isomer-1 was abundant in both endothall formulations, while isomer-2 was only abundant in the monoamine endothall formulation and was more persistent. Degradation did not occur in the absence of sediment. In the presence of sediment degradation if isomer-1 began after a lag phase of 5-11 days and was almost complete by 14 days. Onset of degradation occurred 2-4 days sooner when the microbial population was previously exposed to endothall. We provide direct evidence that the presence and characteristics of sediment are of key importance in the degradation of endothall in an aquatic environment, and that monoamine endothall has two separate isomers that have different degradation characteristics.

An exposition is undertaken to reveal the significant impact of the time-dependent root parameter, on the stability of Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary queueing system. This opens new grounds to stability analysis of non-stationary queueing systems. Potential PSFFA applications of IoT are highlighted.

We describe electron temperature measurements in the SSX MHD wind tunnel using two different methods. First, we estimate T_e along a chord by measuring the ratio of the C__III 97.7 nm to C_IV 155 nm line intensities using a vacuum ultraviolet monochrometer. Second, we record a biasing scan to a double Langmuir probe to obtain a local measurement of T_e. The aim of these studies is to increase the Taylor state lifetime, primarily by increasing the electron temperature. Also, a model is proposed to predict magnetic lifetime of relaxed states and is found of predict the lifetime satisfactorily. Furthermore, we find that proton cooling can be explained by equilibration with the electrons.

Existing implants used with Total Knee Arthroplasty (TKA), Total Hip Arthroplasty (THA), and other joint reconstruction treatments, have displayed premature failures and frequent needs for revision surgery in recent years, particularly with young active patients who represent more than 55% of all joint reconstruction patients. Bone cement and stress shielding have been identified as the major reasons for premature joint failures. A breakdown of the cement may happen, and revision surgery may be needed because of the aseptic loosening. The significant mismatch of stiffness properties of patient trabecular bones and metallic implant materials in joint reconstruction surgery results in the stress shielding phenomenon. This could lead to significant bone resorption and increased risk of bone fracture and the aseptic loosening of implants. The present project introduces an approach for development of customized cellular structures to match the mechanical properties and architecture of human trabecular bone. It consists of four modules:1- characterization of geometry, microarchitecture, and stiffness properties of patient’s bones; 2- developing customized lattice structures tailored to mimic properties established in module 1; 3 - integration of developed lattice structure into full scale implant design and manufacturing; 4- implementation of the developed technology for use in implants that would overcome most of the issues related to aseptic loosening phenomenon. The present work aims at fulfilling the objectives of module 2 by exploring new designs of customized lattice structures and texture tailored to mimic closely patients’ bone anisotropic properties and that can incorporate an engineered biological press-fit fixation technique. The effects of various lattice design variables on mechanical performance of the structure are examined through systematic experimental plan using statistical design of experiments technique and analysis of variance method. All tested lattice designs were explored under realistic geometrical, biological, and manufacturing constraints. Of the four design factors examined in this study, strut thickness was found to have the highest percent contribution (41%) regarding the structure stiffness, followed by unit cell type, and cell size. Srut shape was found to have the lowest effect with only 11% contribution. The introduced solution offers lattice structure designs that can be adjusted to match bone stiffness distribution and promote bone ingrowth and hence eliminating the phenomenon of stress shielding while incorporating biological press-fit fixation technique.

The current work reveals the fine tuning between stability zones and randomness of GI/M/1 Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary D/M/1 queueing system. More specifically, this clearly provides more insights into developing a contemporary PSFFA theory that unifies non-stationary queueing theory with chaos theory and fields in both theoretical physics and chaotic systems. This opens new grounds for stability analysis of non-stationary queueing systems. A notable application of GI/M/1 queueing model to achieve ultra-low latency of autonomous driving service is highlighted. Concluding remarks associated with future avenues of research are given.

Hepatitis B surface antigen (HBsAg) is not only the biomarker of hepatitis B virus (HBV) infection and expression activity in hepatocytes, but also contributes to viral specific T cell exhaustion and HBV persistent infection. Therefore, anti-HBV therapies targeting HBsAg to achieve HBsAg loss are key approaches for HBV functional cure. In this study, we found that YZH-106, a rupestonic acid derivative, inhibited HBsAg secretion and viral replication. Further investigation demonstrated that YZH-106 promoted the lysosomal degradation of viral L- and M-HBs proteins. Mechanistic study by Biacore and docking analysis revealed that YZH-106 bound directly to PreS2 domain of L- and M-HBsAg, thereby blocking their entry to the endoplasmic reticulum (ER) and promoting their degradation in cytoplasm. Our work thereby provide basis for design of novel compound therapy to target HBsAg against HBV infection.

Centrifuges are commonly required devices in medical diagnostics facilities as well as scientific laboratories. Although there are commercial and open source centrifuges, costs of the former and required electricity to operate the latter, limit accessibility in resource-constrained settings. There is a need for low-cost, human-powered, verified and reliable lab-scale centrifuge. This study provides the designs for a low-cost 100% 3-D printed centrifuge, which can be fabricated on any low-cost RepRap-class fused filament fabrication (FFF) or fused particle fabrication (FPF)-based 3-D printer. In addition, validation procedures are provided using a web camera and free and open source software. This paper provides the complete open source plans including instructions for fabrication and operation for a hand-powered centrifuge. This study successfully tested and validated the instrument, which can be operated anywhere in the world with no electricity inputs obtaining a radial velocity of over 1750rpm and over 50N of relative centrifugal force. Using commercial filament the instrument costs about US$25, which is less than half of all commercially available systems; however, the costs can be dropped further using recycled plastics on open source systems for over 99% savings. The results are discussed in the contexts of resource-constrained medical and scientific facilities.

Corona loss generated from conductors is one of the important design factors on ac transmission lines. Based on helical charge simulation method, the 3-D corona loss calculation model considering the conductors’ outer strands in the corona cage is established. With regard to 2-D corona-loss calculation method, the calculation model proposed in this paper can take the electric field strength’s nonuniformity along the axial direction of stranded conductor into consideration, furthermore, it can also calculate the corona loss when the conductor has sag. The calculation results of the LGJ-300/40 and LGJ-400/35 in the small corona cage well coincide with the measurement results, which indicates that the corona-loss calculation model is appropriate. In addition, the corona loss of the bundle conductors 4 × LGJ720 with sag in UHV corona cage is also analyzed.

Abstract: As a low-input crop, Miscanthus offers numerous advantages that, in addition to agricultural applications, permits its exploitation for energy, fuel, and material production. Depending on the Miscanthus genotype, season, and harvest time as well as plant component (leaf versus stem), correlations between structure and properties of the corresponding isolated lignins differ. Here, a comparative study is presented between lignins isolated from M. x giganteus, M. sinensis, M. robustus and M. nagara using a catalyst-free organosolv pulping process. The lignins from different plant constituents are also compared regarding their similarities and differences regarding monolignol ratio and important linkages. Results showed that the plant genotype has the weakest influence on monolignol content and interunit linkages. In contrast, structural differences are more significant among lignins of different harvest time and/or season. Analyses were performed using fast and simple methods such as nuclear magnetic resonance (NMR) spectroscopy. Data was assigned to four different linkages (A: b-O-4 linkage, B: phenylcoumaran, C: resinol, D: b-unsaturated ester). In conclusion, A content is particularly high in leaf-derived lignins at just under 70 % and significantly lower in stem and mixture lignins at around 60 % and almost 65 %. The second most common linkage pattern is D in all isolated lignins, the proportion of which is also strongly dependent on the crop portion. Both stem and mixture lignins, have a relatively high share of approximately 20 % or more (maximum is M. sinensis Sin2 with over 30 %). In the leaf-derived lignins, the proportions are significantly lower on average. Stem samples should be chosen if the highest possible lignin content is desired, specifically from the M. x giganteus genotype, which revealed lignin contents up to 27 %. Due to the better frost resistance and higher stem stability, M. nagara offers some advantages compared to M. x giganteus. Miscanthus crops are shown to be very attractive lignocellulose feedstock (LCF) for second generation biorefineries and lignin generation in Europe.

In the process of metal cutting, the anti-wear performance of the tool determines the life of the tool and affects the surface quality of the workpiece. The finite element simulation method can directly show the tool wear state and morphology, but due to the limitations of the simulation time and complex boundary conditions, it has not been commonly used in tool life prediction. Based on this, a tool wear model was established on the platform of a finite element simulation software for the cutting process of titanium alloy TC4 by end milling. The key technique is to embed different types of tool wear models into the finite element model in combination with the consequent development technology. The effectiveness of the tool wear model is validated by comparing the experimental results with the simulation results. At the same time, in order to quickly predict the tool life, an empirical prediction formula of tool wear was established, and the change course of tool wear under time change was obtained.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

This is a single tertiary center in southwest Romania, population-based, study. We retrospectively compared data obtained in two periods: January 2008 - December 2013 and January 2018 - De-cember 2023, respectively. The global incidence of transposition of great arteries (TGA) - the ter-minated cases added to the ones resulting in live-born pregnancies, remained almost constant. The live-born incidence of TGA decreased (0.34% to 0.013%). The prenatal detection rate increased slightly (71.42% to 87.5%). The median gestational age at the diagnosis decreased, from 29.3 ges-tational weeks (mean 25.4) to 13.4 weeks (mean 17.2). The proportion of terminated pregnancies significantly increased (14.28% to 75%, p = 0.019).

The preparation of transition metal salt ammine complexes having oxidizing anions is a great challenge due to the reaction between the ammonia and oxidizing anions during the synthesis of these materials. However, they have an important role in the development of new oxidants in organic chemistry and especially as precursors in the preparation of mixed metal oxides and alloys in controlled temperature thermal decomposition reactions. Therefore, the synthetic procedures to prepare the complexes of transition metal permanganate, pertechnetate, and perrhenate (VIIB group tetraoxometallates) salts with ammonia as ligand or co-ligand have been comprehensively reviewed. The available data about the structure and spectroscopic properties of these compounds, including the hydrogen bonds that act as redox reaction centers under their thermal decomposition are given and evaluated. Their thermal decomposition processes and products have been summarized. The available pieces of information about their role in organic oxidation reactions like the oxidation of benzyl alcohols, and regeneration of oxo-compounds from oximes and phenylhydrazones including the kinetics of these processes have also been collected.

High concentrations of Na⁺ or [Co(NH₃)₆]³⁺ can induce the B to Z conformational transition in alternating (dC-dG) oligo and polynucleotides. The use of short DNA oligomers (dC-dG)₄ and (dm⁵C-dG)₄ as models can allow a thermodynamic characterization of the transition. Both form right handed double helical structures (B-DNA) in standard phosphate buffer with 115 mM Na⁺ at 25 ^oC. However, at 2.0 M Na⁺ or 200 mM [Co(NH₃)₆]³⁺, (dm⁵C-dG)₄ assumes a left handed double helical structure (Z-DNA) while the unmethylated (dC-dG)₄ analogue remains right handed under those conditions. We have previously demonstrated that the enthalpy of the transition at 25 ^oC for either inducer can be determined using isothermal titration calorimetry (ITC) [Ferreira, J. M. & Sheardy, R. D., Biophys. J. 2006, 91, 1–7]. Here, ITC is used to investigate the linkages between temperature, water activity and DNA conformation. We found that the determined enthalpy for each titration varied linearly with temperature allowing determination of the heat capacity change (DC_p) between the initial and final states. As expected, the DC_p values were dependent upon the cation (i.e. Na⁺ vs [Co(NH₃)₆]³⁺) as well as the sequence of the DNA oligomer (i. e., methylated vs unmethylated). Osmotic stress experiments were carried out to determine the gain or loss of water by the oligomer induced by the titration. The results are discussed in terms of solvent accessible surface areas, electrostatic interactions and the role of water.

Persistent, non-explosive passive degassing is a common characteristic of active volcanoes. Distinct periodic components in measurable parameters of gas release have been widely identified over timescales ranging from seconds to months. The development and implementation of high temporal resolution gas measurement techniques now enables the robust quantification of high frequency processes operating on timescales comparable to those detectable in geophysical datasets. This review presents an overview of the current state of understanding regarding periodic volcanic degassing, and evaluates the methods available for detecting periodicity, e.g., autocorrelation, variations of the Fast Fourier Transform (FFT), and the continuous wavelet transform (CWT). Periodicities in volcanic degassing from published studies are summarised and statistically analysed, together with analyses of literature-derived datasets where periodicity had not previously been investigated. Finally, an overview of current knowledge on drivers of periodicity is presented and discussed in the framework of four main generating categories, including: (1) non-volcanic (e.g., atmospheric or tidally generated); (2) gas-driven, shallow conduit processes; (3) magma movement, intermediate to shallow storage zone; and (4) deep magmatic processes.

Despite the high quality of soybean protein, raw soybeans and soybean meal cannot be directly included into animal feed mixtures due to the presence of Kunitz (KTi) and Bowman Birk protease inhibitors (BBi) which reduces animal performance. Heat treatment can substantially inactivate trypsin and chymotrypsin inhibitors (BBi) but such treatment is energy intensive, adds expense, and negatively impact the quality of seed proteins. As an alternative approach we have employed CRISPR/Cas9 gene editing to create mutations in BBi genes to drastically lower the protease inhibitor content in soybean seed. Agrobacterium-mediated transformation was used to generate several stable transgenic soybean events. These independent CRISPR/Cas9 events were examined in comparison to wild type plants using Sanger sequencing, proteomic analysis, trypsin/chymotrypsin inhibitor activity assays and q15RT-PCR. Collectively, our results demonstrate the creation of an allelic series of loss of function mutations affecting the major BBi gene in soybean. Mutations in two of the highly expressed seed specific BBi genes lead to substantial reductions in both trypsin and chymotrypsin inhibitor activities.

This study investigates the emergence of ertapenem-resistant, meropenem-susceptible (ErMs) among non-carbapenemase producing (NCP) and carbapenemase producing (CP) Escherichia coli and Klebsiella pneumoniae. As mutations for ertapenem resistance establish the genetic background for non-carbapenemase meropenem resistance, there is a great need for antibiotic stewards and researchers to understand the determinants of a strain’s propensity to become resistant. Whole genome sequencing was conducted on clinical carbapenem-resistant E. coli (CREC) and K. pneumoniae (CRKP) across 5 hospitals in San Antonio, U.S. from 2012-2018. The majority of carbapenem resistant Enterobacterales (CRE) were NCP (54%; 41/76). The blaCTX-M was found to be most prevalent among NCP isolates (p = 0.02). LC-MS/MS analysis of carbapenem hydrolysis revealed that blaCTX-M-mediated carbapenem hydrolysis, indicating the need to reappraise the term, “non-carbapenemase (NCP)” for quantitatively uncharacterized CRE strains harboring blaCTX-M. Antimicrobial susceptibility results showed that 56% of all NCPE isolates had an ErMs phenotype (NCPE vs. CPE, p < 0.001), with E. coli driving the phenotype (E. coli vs. K. pneumoniae, p < 0.001). ErMs strains carrying blaCTX-M, had approximately 4-fold more copies of blaCTX-M than ceftriaxone-resistant but ertapenem and meropenem susceptible (EsMs) isolates (3.7 v. 0.9, p < 0.001). ErMs also carried more mobile genetic elements (MGEs), particularly IS26 composite transposons, than EsMs (37 vs. 0.2, p < 0.0001). Immunoblot analysis demonstrated the absence of OmpC expression in NCP-ErMs E. coli, with 92% of strains lacking full contig coverage of ompC. Overall, this work provides evidence of a collaborative effort between blaCTX-M and OmpC in NCP strains that confer resistance to ertapenem but not meropenem. To thwart potential mismanagement of CRE infected patients, future efforts should focus on understanding the mechanism(s) underlying OmpC loss, developing rapid methods to detect blaCTX-M copy number variants, and targeted antimicrobials for NCPE and ErMs strains.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

Although distributed additive manufacturing can provide high returns on investment the current markup on commercial filament over base polymers limits deployment. These cost barriers can be surmounted by eliminating the entire process of fusing filament by 3-D printing products directly from polymer granules. Fused granular fabrication (FGF) (or fused particle fabrication (FPF)) is being held back in part by the accessibility of low-cost pelletizers and choppers. An open-source 3-D printable invention disclosed here provides for precise controlled pelletizing of both single thermopolymers as well as composites for 3-D printing. The system is designed, built and tested for its ability to provide high tolerance thermopolymer pellets from a number of sizes capable of being used in a FGF printer. In addition, the chopping pelletizer is tested for its ability to chop multi-materials simultaneously for color mixing and composite fabrication as well as precise fractional measuring back to filament. The US$185 open-source 3-D printable pelletizer chopper system was successfully fabricated and has a 0.5 kg/hr throughput with one motor, and 1.0 kg/hr throughput with two motors using only 0.24 kWh/kg during the chopping process. Pellets were successfully printed directly via FGF and indirectly after being converted into high-tolerance filament in a recyclebot.

In an effort to enhance the efficiency and safety of open-pit mines, this study explores the optimization of end slope road parameters and slope structures, specifically focusing on unmanned driving lanes.A significant aspect of the study is the development of a truck trajectory offset model, which considers the different reaction times between automated sensors and human drivers in adapting to environmental changes. To test these concepts, the study uses numerical simulations to confirm the stability of the proposed end slope designs. Using Victory West Mine No. 1 as a case study, the research determines the optimized width for unmanned driving lanes and the maximum angle for safe steepening of end slopes. The findings indicate that the optimized unmanned lane width for NTE240 mining dump trucks is 1743 mm, allowing for a 2-degree increase in the slope angle at the south end slope. This optimization leads to a steep mining stripping volume of 3.2735 million m³ and a coal output of 2.49628 million tons, maintaining a stripping ratio of 1.31m³/t. These results demonstrate that the unmanned driving road width optimization not only ensures slope safety but also significantly boosts the economic benefits of steep mining in open-pit mines.

From a differential geometric perspective, information geometry (IG) aims to characterise the structure of statistical geodesic models. The research done for this paper offers a novel method for modelling the information geometry of a queuing system. From the perspective of IG, the manifold of the transient M/M/infinity queue is described in this context. The Fisher Information matrix (FIM) as well as the inverse of (FIM), (IFIM) of transient M/M/infinity QM are devised. In addition to that, new results that uncovered the significant impact of stability of QM on the existence of (IFIM) are obtained. Moreover, the Geodesic equations of motion of the coordinates of the underlying transient are obtained. Also, it is revealed that stable QM is developable (i.e., has a zero Gaussian curvature) and has a non-zero Ricci Curvature Tensor (RCT). Novel stability dynamics of transient M/M/iInfinity queue manifold is revealed by discovering the mutual dual impact between the behaviour of (RCT) and the stability(instability) phases of M/M/Infinity QM. Furthermore, a new discovery that presents the significant impact of stability of queue manifold and the continuity of the unique representation between M/G/1 queue manifold and Ricci Curvature Tensor (RCT). The information matrix exponential (IME) is devised. Also, it is shown that stability of the devised (IME) enforces the instability of M/M/ Infinity QM. More interestingly, novel relativistic info-geometric queueing theoretic links are revealed .

Recent studies have demonstrated a relationship between poor vitamin D status and respiratory infections and diarrhea among young children. Acute lower respiratory infections (ALRI) and diarrhea are among the two most important causes of death in under-5 children. In this analysis, we examine the extent to which vitamin-D deficiency (<10 ng/ml) predicts these outcomes using data from a randomized controlled trial (RCT) of daily folic acid and/ or vitamin B12 supplementation for six months in 6 to 30 months old children conducted in Delhi, India. Of the 960 subjects who had vitamin-D concentrations measured, 331(34.5%) were vitamin-D deficient. We found, after controlling for relevant potential confounders (age, sex, breastfeeding status, wasting, stunting, underweight, anemia status at base line and season), the risk of ALRI was significantly higher among vitamin-D deficient (OR 1.26; 95% CI: 1.03 to 1.55) compared to vitamin-D-replete children in the six months follow-up period. Vitamin-D status was not significantly associated with episodes of diarrhea and clinical pneumonia. The extent of causal relationship of vitamin-D status and ALRI needs to be explored in further studies.

Access to nasopharyngeal swabs for sampling remain a bottleneck in some regions for COVID-19 testing. This study develops a distributed manufacturing solution using only an open source manufacturing tool chain consisting of two types of open source 3-D printing and batch UV curing, and provides a parametric fully free design of a nasopharyngeal swab. The swab was designed using parametric OpenSCAD in two components (a head with engineered break point and various handles), which has several advantages: i) minimizing print time on relatively slow SLA printers, ii) enabling the use of smaller print volume open source SLA printers, iii) reducing the amount of relatively expensive UV resin, and iv) enabling production of handle on more accessible material extrusion 3-D printers. A modular open source UV LED box was designed, fabricated for $45 and tested for batch curing. Swabs can be fabricated for $0.06-$0.12/swab. The results of the mechanical validation tests showed that the swabs could withstand greater forces than would be expected in normal clinical use. The swabs were also able to absorb a significant amounts of synthetic mucus materials and passed abrasion and handling tests. The results show the open source swab are promising candidates for clinical trials.

Smallholder dairying engages around 70 to 80 million rural households who are mostly landless, small and marginal farmers. These farmers face challenges in terms of adoption of balanced feeding practices including inclusion of compound feed in animal feeding. This necessitates to understand the socio-economic factors that are influencing the adoption of compound feed. The study found that 51% of dairying households adopted compound feed in animal feeding. The adopters and non-adopters of compound feed differed (P< 0.01) in terms of land holding, family educational status, breeds owned, membership status in farmer’s collectives, fodder adoption, area under fodder, access to grazing resources, availability of crop residues, milk production and milk marketing opportunities. Furthermore, users and non-users of compound feed had significant difference (P< 0.05) in extension agency contact, mass media contact, attitude towards dairying and gender participation in farming. The logit regression model explained the variance in adoption to 30%. Further it indicated the role of selective socio-economic characters, farming situations, feeding and marketing practices in adoption of compound feed. In specific membership in farmer’s collectives, marketing opportunity, milk production, farm men participation, family education status, grazing resources and attitude towards dairying has greatly influenced the adoption behaviour of compound feed in positive direction. Added, households with high experience, cultivating fodder and having access to crop residues tend to influence the adoption decision negatively. The research observed that farmers tend to use compound feed for increasing productivity in areas of better markets and there exists trade-offs between milk market opportunities, access to cheaper roughages and usage of compound feed.

Commonly employed methods for reversibly disrupting gene expression, such as those based on RNAi or CRISPRi, are rarely capable of achieving >80-90% downregulation, making them unsuitable for targeting genes that require more complete disruption to elicit a phenotype. Genetic deletion, on the other hand, while enabling complete disruption of target genes, often produces undesirable irreversible consequences such as cytotoxicity or cell death. Here we describe the design, development and detailed characterization of a dual-function "TRE-Lox" system for effecting either (a) doxycycline (Dox)-mediated downregulation or (b) genetic deletion of cathepsin D (CatD), based on targeted insertion of a tetracycline-response element (TRE) and two LoxP sites into the 5' end of the endogenous gene (CTSD). Using an optimized reverse-tetracycline transrepressor (rtTR) variant fused with the Krüppel-associated box (KRAB) domain, we show that CatD expression can be disrupted by as much as 98% in mouse embryonic fibroblasts (MEFs). This system is highly sensitive to Dox (IC50 = 1.46 ng/mL) and results in rapid (t1/2 = 0.57 d) and titratable downregulation of CatD. Notably, even near-total disruption of CatD expression was completely reversed by withdrawal of Dox. As expected, transient expression of Cre recombinase results in complete deletion of the CTSD gene. The dual functionality of this novel system will facilitate future studies of the involvement of CatD in various diseases, particularly those attributable to partial loss of CatD function. In addition, the TRE-Lox approach should be applicable to the regulation of other target genes requiring more complete disruption than can be achieved by traditional methods.

Appropriate nutrition during pregnancy and the post-partum period is vital to both the parent and their offspring. Both under- and over-nourished status may have important microbial implications on the parental and infant gut microbiomes. Alterations to the microbiome can have implications for a person’s risk of obesity and metabolic diseases. In this review, we examine alterations in the parental gut, vaginal, placental, and milk microbiomes in the context of pre-pregnancy BMI, gestational weight gain, body composition, gestational diabetes, and parental diet. We also investigate how the infant gut microbiome may be altered by these different parameters. Many of the microbial changes seen in under- and over-nourished states in birthing parents may result in long-term implications to the health of offspring. Differences in diet appear to be a major driver of the parental, and subsequently milk and offspring microbiomes. Further prospective longitudinal cohort studies are needed examining nutrition and the microbiome to better understand its implications. Additionally, trials involving dietary interventions in child-bearing age adults should be explored to improve the parent and child’s risks for metabolic diseases.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

A new set of basis functions is presented. The foundation in mathematics is established. To reconstruct a signal, it is compared to the Fourier basis functions. The M-basis functions' potential applications are also presented.

Open-source 3-D printing has played a pivotal role in revolutionizing the additive manufacturing (AM) landscape, by making distributed manufacturing economic, democratizing access, and fostering far more rapid innovation than antiquated proprietary systems. Unfortunately, some 3-D printing manufacturing companies began deviating from open-source principles and violating licenses for the detriment of the community. To determine if a pattern has emerged of companies patenting clearly open-source innovations, this study presents three case studies from the three primary regions of open-source 3-D printing development (EU, U.S. and China) as well as three aspects of 3-D printing technology (AM materials, an open-source 3-D printer, and core open-source 3-D printing concepts used in most 3-D printers). The results of this review have shown that non-inventing entities called patent parasites are patenting open-source inventions already well-established in the open source community and in the most egregious cases commercialized by one (or several) firms at the time of the patent filing. Patent parasites are able to patent open-source innovations by using a different language, vague patent titles and broad claims that encompass enormous swaths of widely diffused open-source innovation space. This practice poses a severe threat to innovation and several approaches to irradicate the threat are discussed.

Chronic kidney disease (CKD) is a major non-communicable disease associated with high rates of premature morbidity and mortality. The prevalence of hypovitaminosis D (deficiency of 25(OH)D or 25D) is greater in racial/ethnic minorities and in patients with CKD than the general population. Low 25D is associated with bone and mineral disorders as well as immune, cardiometabolic and cardiovascular (CV) diseases. Thus, it has been suggested low 25D contributes to the poor outcomes in patients with CKD. The prevalence of hypovitaminosis D rises progressively with advancing severity of kidney disease with over 30% of patients with CKD stage 3 and 70% patients with CKD stage 5 estimated to have low levels of 25D. This report describes several of the abnormal physiologic and counter-regulatory actions related to low 25D in CKD such as those in oxidative stress and inflammatory systems, and some of the preclinical and clinical evidence or lack of thereof of normalizing serum 25D levels to improve outcomes in patients with CKD, and especially for the high risk subset of racial/ethnic minorities who suffer from higher rates of advanced CKD and hypovitaminosis D.

This work presents the results of three connection types in double-shear with dowel fasteners, using the simplified equations from the Eurocode 5. All design parameters were established and compared using three different wood strength and density properties, which constitute the members connections. Eighty-one connections were obtained, allowing to conclude about the number of fasteners needed to the applied tensile load. An increase in the number of dowels was obtained with the increased applied tensile load, lower dowel diameter, lower wood density, and lower strength material in all connection types in the study. The design characteristic load-carrying capacity per shear plane and fastener also decrease with the previously considered parameters.

Background: As cancer progresses, cells acquire traits that allow them to disperse and disseminate to distant locations in the body – a process known as metastasis. While in the vasculature, these cells are referred to as circulating tumour cells (CTCs) and can manifest either as single cells or clusters of cells (i.e., CTC clusters), with the latter being the most aggressive. The increased metastatic potential of CTC clusters is generally associated with cooperative group benefits in terms of survival, such as increased resistance to shear stress, anoikis, immune attacks and drugs. However, the adoption of a group phenotype poses a challenge when exiting the vasculature (extravasation) as the large size can hinder the passage through vessel walls. Despite their significant role in the metastatic process, the mechanisms through which CTC clusters extravasate remain largely unknown. Based on the observed in vivo association between CTC clusters and platelets, we hypothesized that cancer cells take advantage of the platelet-derived Transforming Growth Factor Beta 1 (TGF-β1) – a signalling factor that has been widely implicated in many aspects of cancer, to facilitate their own dissemination. To address this possibility, we evaluated the effect of exogenous TGF-β1 on an experimentally evolved non-small lung cancer cell line that we previously developed and used to investigate the biology of CTC clusters. Results: We found that exogenous TGF-β1 induced the dissociation of clusters into adherent single cells. Once adhered, cells released their own TGF-β1 and were able to individually migrate and invade in the absence of exogenous TGF-β1. Based on these findings we developed a model that involves a TGF-β1-mediated plastic switch between a cooperative phenotype and a single-celled stage that enables the extravasation of CTC clusters. Conclusions: This model allows for the possibility that therapies can be developed against TGF-β1 signalling components and/or TGF-β1 target genes to suppress the metastatic potential of CTC clusters. Considering the negative impact that metastasis has on cancer prognosis and the lack of therapies against this process, interfering with the ability of CTC clusters to switch between cooperative and individual behaviours could provide new strategies to improve patient survival.

Viral infection can regulate the cell cycle, thereby promoting viral replication. Hijacking and altering the cell cycle are important for the virus to establish and maintain latent infection. Previously, Spodoptera exigua multiple nucleopolyhedrovirus (SeMNPV) latently infected P8-Se301-C1 cells, which grew more slowly than Se301 cells and interfered with homologous SeMNNPV superinfection, were established. However, the effects of latent and superinfection with baculoviruses on cell cycle progression remain unknown. In this study, the cell cycle profiles of P8-Se301-C1 cells, and SeMNPV or Autographa californica mutiple nucleopolyhedrovirus (AcMNPV) infected P8-Se301-C1 cells were characterized by flow cytometry. The results showed that replication-related genes MCM4, PCNA, and BAF were down-regulated (p < 0.05) in P8-Se301-C1 cells and the S phase of P8-Se301-C1 cells was longer than that of Se301 cells. P8-Se301-C1 cells infected with SeMNPV did not arrest in G2/M phase and or affect the expression of Cyclin B and cyclin-dependent kinase 1 (CDK1). Furthermore, when P8-Se301-C1 cells were infected with SeMNPV after synchronized treatment with hydroxyurea and nocodazole, light microscopy and qRT-PCR analysis showed that compared with unsynchronized cells and S and G2/M phase cells, SeMNPV-infected P8-Se301-C1 cells in G1 phase induced G2/M phase arrest, and the amount of virus adsorption and intracellular viral DNA replication were significantly increased (p < 0.05). In addition, the BV production and the OB containing cells were both increased at 120 h post-infection (p < 0.05). The expression of Cyclin B and CDK1 was significantly down-regulated at 48 h post infection (p < 0.05). Finally, arrest of SeMNPV-infected G1 phase cells in the G2/M phase increased BV production (p < 0.05) and the number of OB containing cells. In conclusion, G1 phase infection and G2/M arrest are favorable to SeMNPV proliferation in P8-Se301-C1 cells, thereby alleviating the homologous superinfection exclusion. The results contribute to a better understanding of the relationship between baculoviruses and insect cell cycle progression regulation.

Vitamin D has previously been quantified in some plants and algae, particularly in leaves of the Solanaceae family. We measured the vitamin D content of Australian native food plants and Australian-grown edible seaweed. Using liquid chromatography with triple quadrupole mass spectrometry, 13 samples (including leaf, fruit and seed) were analysed in duplicate for vitamin D₂, vitamin D₃, 25-hydroxyvitamin D₂ and 25-hydroxyvitamin D₃. Five samples contained vitamin D₂: raw wattleseed (Acacia victoriae) (0.03 µg/100 g dry weight (DW)); fresh and dried lemon myrtle (Backhousia citriodora) leaves (0.03 and 0.24 µg/100 g DW, respectively); dried leaves and berries of Tasmanian mountain pepper (Tasmannia lanceolata) (0.67 and 0.05 µg/100 g DW, respectively). Fresh kombu (Lessonia corrugata) contained vitamin D₃ (0.01 µg/100 g DW). Detected amounts were low; however, it is possible that exposure to ultraviolet radiation may increase the vitamin D content of plants and algae if vitamin D precursors are present.

Our study assessed the impact of using ovitraps with pyriproxyfen on mosquito populations and the feasibility of using human saliva samples to test for seroconversion to dengue virus (DENV). We used a quasi-experimental research design by forming the intervention (n=220) and the control (n=223) groups in neighboring Taguig City, Philippines, over four months. Socio-demographic data, entomological indices, and IgG antibodies against DENV were measured. Associations between the implementation of ovitraps dosed with pyriproxyfen and mosquito densities (percentage positive ovitraps and container indices) and DENV seroconversion were calculated post-intervention in Months 2, 3, and 4. Among participants recruited at baseline, 17 and 13 were seropositive for dengue (DENV) in the intervention and control groups, respectively. Both entomological indices were lower in the treated area than the control site at months two, three, and four post-interventions but not earlier. Dengue seroconversions rates did decrease in the treated population but not significantly so. In conclusion, the use of PPF-treated ovitraps impacted the mosquito population but not the seroconversion rates. Compliance to provide saliva samples and the ability to detect IgG antibodies within these samples were encouraging and suggested that further studies on a larger population and longer duration are warranted.

We report on the occurrence of natural Magnesium Alumina Silicate Hydrate (M-(A)-S-H) cement at Feragen and Leka in eastern and western Trøndelag Norway, respectively. Both occurrences are located in the sub-arctic climate zone and form in glacial till and moraine material deposited on ultramafic rock during the Weichselian glaciation. Weathering of serpentinized peridotite dissolve brucite and result in a relative high pH alkaline fluid that subsequently reacts with the felsic minerals of the till (quartz, plagioclase, K-feldspar) to form a cement consisting of an amorphous material or a mixture of nanocrystalline Mg-rich phyllosilicates, including illite. The presence of plagioclase in the till results in the enrichment of alumina in the cement, i.e., forms M-A-S-H instead of the M-S-H cement. Dissolution of quartz results in numerous etch-pits and negative quartz crystals filled with M-A-S-H cement. Where the quartz dissolution is faster that the cement precipitation, a honeycomb-like texture is formed. Compositionally the cemented till (tillite) contains more MgO and has a higher loss of ignition than the till, suggesting that the cement is formed by a MgO fluid that previously reacted with the peridotite. The M-(A)-S-H cemented till represent a new type of duricrust, coined magsilcrete. The study of natural Mg-cement provides information on peridotites as a Mg-source for Mg-cement and as a feedstock for CO2 sequestration.

The flexitarian diet, which emphasizes a reduction in meat consumption, has been identified as a crucial factor in transitioning to sustainable food systems that can help combat climate change and improve food and nutritional security, particularly in areas where food choices are abundant. Despite Brazil being a major meat producer, meat consumption among Brazilians has been decreasing in recent years, with a growing portion of the population adopting meat-free and meat-reduced dietary models. In this study, we conducted the first non-industry funded scientific investigation of Brazilian flexitarians, with the goal of characterizing their socio-economic and demographic characteristics, motivations for adopting flexitarianism, frequency of animal-based meat consumption, and main substitutes consumed. Data was collected from 1029 self-identified flexitarians in Brazil. Our findings indicate that the flexitarian food model is primarily adopted by women and is motivated by concerns about the environmental impact of meat consumption, personal health, and animal welfare. Flexitarians were found to have a consumption profile that can be divided into three groups: low (consuming meat 36 times a week), medium (consuming meat 7 times a week), and high (consuming meat 4 times a week). The flexitarian meals pattern is characterized by lower consumption of beef (less than 2 times per week) and higher consumption of chicken (3 times per week) and is supplemented by plant-based protein sources and eggs as the main meat substitutes.

The misuse of antibiotics during the last decades led to the emergence of multidrug resistant pathogenic bacteria. This phenomenon constitutes a major public health issue. Consequently, the discovery of new antibacterials in the short term is crucial. Colicins, due to their antibacterial properties, thus constitute good candidates. These toxin proteins, produced by E. coli to kill enteric relative competitors, exhibit cytotoxicity through ionophoric activity or essential macromolecule degradation. Among the 25-colicin types known to date, colicin M (ColM) is the only one colicin interfering with peptidoglycan biosynthesis. Accordingly, ColM develops its lethal activity in E. coli periplasm by hydrolyzing the last peptidoglycan precursor, lipid II, into two dead-end products, thereby leading to cell lysis. Since the discovery of its unusual mode of action, several ColM orthologs have also been identified based on sequence alignments; all of the characterized ColM-like proteins display the same enzymatic activity of lipid II degradation and narrow antibacterial spectra. This publication aims at being an exhaustive review about what is currently known on this new family of antibacterial enzymes as well as on their potential use of food preservatives or therapeutic agents.

The study is devoted to analyzing the economic sustainability of the town of Amherst, MA. The city's top employer and core enterprise is the University of Massachusetts Amherst, with over 32,000 students and almost 2,000 staff members. Based on a literature review, a hypothesis was put forward that a university city should have a high level of economic sustainability. To assess economic sustainability, the USCESI Index was developed. It evaluates sustainability in three groups of parameters: society, economy, and ecology. The first group includes the level of racial diversity, the level of education of the population, and the access to medical services. The second group consists of the Gini coefficient by income level, the median cost of housing, and the unemployment rate. The environmental situation is assessed according to the Air Quality Index developed by the US Environmental Protection Agency. For comparison, the town of Braintree, MA, was taken. The USCESI was calculated for both locations. The analysis showed that both Amherst and Braintree have a high degree of economic sustainability. However, it was revealed that proximity to a significant economic center has a more powerful positive impact on economic sustainability than the location of a large university.

In this paper, an intelligent blind guide system based on 2D LiDAR and RGB-D camera sensing is proposed, and the system is mounted on the smart cane. The intelligent guide system relies on 2D LiDAR, RGB-D camera, IMU, GPS, Jetson nano B01, STM32 and other hardware. The main advantage of the intelligent guide system proposed by us is that the distance between the smart cane and obstacles can be measured by 2D LiDAR based on Cartographer algorithm, thus achieving Simultaneous localization and mapping (SLAM). At the same time, through the improved yolov5 algorithm, pedestrians, vehicles, pedestrian crosswalks, traffic lights, warning posts, stone piers, tactile paving and other objects in front of the visually impaired can be quickly and effectively identified. Laser SLAM and improved yolov5 obstacle identification tests were carried out inside a teaching building on the campus of Hainan Normal University and on a pedestrian crossing on Longkun South Road in Haikou City, Hainan Province. The results show that the intelligent guide system developed by us can drive the wheels and omnidirectional wheels at the bottom of the smart cane, and give the smart cane a self-leading blind guide function like a "guide dog", which can effectively guide the visually impaired to avoid obstacles and reach the predetermined destination, and can quickly and effectively identify the obstacles on the way out. The laser SLAM speed of this system is 25~31FPS, which can realize the short-distance obstacle avoidance and navigation function both in indoor and outdoor envionments. The improved yolov5 helps to identify 86 types of objects, the recognition rate for pedestrian crosswalks and for vehicles are 84.6% and 71.8%, respectively; the overall recognition rate for 86 types of objects is 61.2%, and the obstacle recognition rate of the intelligent guide system is 25-26FPS.

Transplant oncology is a relatively new field in which transplantation is used to treat patients who would otherwise be unresectable. New anticancer treatment paradigms using tumor and transplant immunology and cancer immunogenomics are emerging. In turn, liver transplantation (LT) has become a potential therapy for certain patients with colorectal cancer (CRC) with liver metastasis, hepatocellular (HCC), cholangiocarcinoma (CCA), and metastatic neuroendocrine tumor (NET) to the liver. Although there are established criteria for LT in HCC, the evidence regarding LT as a treatment modality for certain gastrointestinal malignancies is still debated. The aim of this review is to highlight updates in the role of LT for certain malignancies, including HCC, metastatic CRC, hilar CCA, and neuroendocrine tumor (NET), as well as contextualize LT use and discuss controversies in transplant oncology.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Shot peening is an attractive technique for fatigue enhanced performance of metallic components, because it promotes crack initiation retardation and later crack growth. Engineering design based on fatigue crack propagation predictions applying the principles of fracture mechanics is commonly used in aluminum structures for aerospace engineering. The main purpose of present work was to analyze the effect of shot peening on the fatigue crack propagation of the 7475 aluminum alloy, under both constant amplitude loading and periodical overload blocks. The tests were performed on 4 and 8 mm thickness specimen's with stress ratios of 0.05 and 0.4. The analysis of the shot-peened surface showed a small increase of the micro-hardness values, due to the plastic deformations imposed by shot peening. The beneficial effect of surface peening on fatigue crack growth rates is quite limited to an increasing near the threshold. The specimens’ thickness has only marginal influence on the crack propagation, in opposite to the stress ratio. Periodic overload blocks of 300 cycles promotes a reduction of the fatigue crack growth rate for both intervals of 7,500 and 15,000 cycles.

Extreme-mass-ratio inspirals (EMRIs) are significant observational targets for spaceborne gravitational wave detectors, namely, LISA, Taiji, and Tianqin, which involve the inspiral of stellar-mass compact objects into massive black holes with a mass range of approximately 104∼107M⊙. EMRIs are estimated to produce long lived gravitational wave signals with more than 105 cycles before plunge, making them an ideal laboratory for exploring the strong-gravity properties of the spacetimes around the MBHs, stellar dynamics in galactic nuclei, and properties of the MBHs itself. However, the complexity of the waveform model, which involves the superposition of multiple harmonics, as well as the high-dimensional and large-volume parameter space, make the fully coherent search challenging. In our previous work, we proposed a 10-dimensional search using Particle Swarm Optimization (PSO) with local maximization over the three initial angles. In this study, we extend the search to an 8-dimensional PSO with local maximization over both the three initial angles and the angles of spin direction of the MBH where the latter contribute a time independent amplitude to the waveforms. Additionally we propose a 7-dimensional PSO search by using a fiducial value for the initial orbital frequency and shifting the corresponding 8-dimensional Time Delay Interferometry responses until a certain lag returns the corresponding 8-dimensional log-likelihood ratio maximum. The reduced dimensionality likelihoods enable us to successfully search for EMRI signals with duration of 0.5 years and signal-to-noise ratio of 50 within a wider search range than our previous study. We discuss further developments, such as using a hierarchical search to narrow down the search ranges of certain parameters, and applying Graphics Processing Units to speed up the code. These advances aim to improve the efficiency and accuracy of the EMRI search algorithm.

Serious outbreaks of foodborne disease have been caused by Listeria monocytogenes found in retail delicatessens and the severity of disease is significant, with high hospitalization and mortality rates. Little is understood about the formidable public health threat of L. monocytogenesin all four niches, humans, animals, food and environment in Egypt. This study analyzed the presence of L. monocytogenes collected from the four environmental niches and bioinformatic analysis was implemented to analyze and compare the data. PCR was used to detect virulence genes encoded by pathogenicity island (LIPI-1). prfA amino acid substation that causes constitutive expression of virulence was common in 77.7% of isolates. BLAST analysis did not match other isolates in the NCBI database suggesting this may be a characteristic of the region associated with these isolates. A second group included the NH1 isolate originating in China, and BLAST analysis showed this prfA allele was shared with isolates from other global locations such as Europe and North America. Identification of possible links and transmission pathways between the four niches, helps to decrease the risk of disease in humans, to take more specific control measures in the context of disease prevention, to limit economic losses associated with food recalls and highlightens the need to treatment options.

The design of highly efficient sensitizers is one of the most significant areas in dye-sensitized solar cell (DSSC) research. We have studied a series of benzothiadiazole-based D-π-π-A organic dyes, putting emphasis on the influence of the donor moiety on the DSSC’s efficiency. Using linear response time-dependent density functional theory (TDDFT) with the CAM-B3LYP functional different donor groups were characterized in terms of electronic absorption spectra and key photovoltaic parameters. As a reference a dye has been considered which has a benzothiadiazole fragment linked via thiophene rings to a diphenylamine donor and a cyanoacrylic acid acceptor. The different systems are first studied in terms of individual performance parameters, which are eventually aggregated into the power conversion efficiency. Here only the amino-substituted species shows a modest increase, whereas the dimethylamino case even shows a decrease.

Salt marshes are globally important ecosystems, but many have been lost or transformed due to the impacts of global change. There have been attempts to broadly quantify salt marsh communities, especially the ubiquitous grasses which serve as foundation species such as Spartina alterniflora and Spartina patens, the latter of which is being lost due to sea level rise. However, few researchers have used high-resolution geospatial imagery to quantify fine-scale changes in the distribution of grasses or to track losses of S. patens. To address this issue, we utilized a simple and rapid method of classifying geospatial marsh imagery with cloud-based machine learning in Google Earth Engine (>92% accuracy for S. patens regardless of imagery age). Our methods allowed us to characterize full landscapes (two geospatially proximal areas, >7,000 ha each) of critical salt marshes on the New Jersey coast and to evaluate fine-scale (1-m) community transformations in response to global change with imagery from 2006 to 2019. Notably, one marsh experienced very little change while the other experienced an 81.17% (1,087 ha) loss of S. patens, illuminating disparate patterns of change for two geographically proximal ecosystems. Further exploration revealed an association in the loss of S. patens with increases in streamflow and total nitrogen content in the rivers that run through each marsh. These results signify the importance of broad-scale ecological studies that evaluate fine-scale community transformations and for management strategies that do not generalize across landscapes of an ecosystem-type.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Hashimoto's thyroiditis (HT) is essentially featured by self-tissue destruction by means of the adaptive immune responses that evade immune regulation. Vitamin D carries out an immunomodulatory role that appears to promote immune tolerance. The aim of this study is to elaborate a narrative review about the relationship between vitamin D status and HT and the role of vitamin D supplementation to reduce HT risk by modulating the immune system. There is an extensive literature confirming that vitamin D levels are significantly lower in HT patients compared to healthy people. On the other hand, after the supplementation with cholecalciferol in patients with HT and vitamin D deficiency, thyroid autoantibody titer decreased significantly, However, there are no conclusive results on the effect of vitamin D supplementation on the thyroid function. The confirmation of the beneficial effects of vitamin D in the prevention and treatment of autoimmune thyroid diseases require additional randomized, double-blind, placebo-controlled trials with longer follow-up.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

Extensive genome structure variation, such as copy number variations (CNVs) and presence/absence variations, is the basis for the remarkable maize genetic diversity; however, the effect of CNVs on maize herbivory defense remains largely underexplored. Here, we report that the naturally occurring duplication of the maize 9-lipoxygenase gene, ZmLOX5, leads to increased resistance of maize to herbivory by fall armyworms (FAW). Previously, we showed that ZmLOX5-derived oxylipins are required for defense against chewing insect herbivores and identified several inbred lines, including Yu796, that contained duplicated CNVs of ZmLOX5, referred to as Yu796-2×LOX5. To test whether introgression of the Yu796-2×LOX5 locus into the herbivore-susceptible B73 background that contains a single ZmLOX5 gene is a feasible approach to increase resistance, we generated a series of near-isogenic lines that contained either 2, 1 or 0 copies of the Yu796-2×LOX5 locus in the B73 background by six back crosses (BC6). Droplet digital PCR (ddPCR) confirmed the successful introgression of the Yu796-2×LOX5 locus in B73. The resulting B73-2×LOX5 inbred line displayed increased resistance against FAW associated with increased expression of ZmLOX5, increased wound-induced production of its primary oxylipin product, the α-ketol, 9-hydroxy-10-oxo-12(Z),15(Z)-octadecadienoic acid (9,10-KODA), and the downstream defense hormones regulated by this molecule, 12-oxo-phytodienoic acid (12-OPDA) and abscisic acid (ABA). Surprisingly, wound-induced JA-Ile production was not increased in B73-2×LOX5, resulting from the increased JA catabolism. Furthermore, B73-2×LOX5 displayed enhanced drought tolerance likely due to increased ABA and 12-OPDA content. Taken together, this study revealed that the duplicated CNV of ZmLOX5 quantitively contributes to maize antiherbivore defense and presents proof-of-concept evidence that the introgression of naturally occurring duplicated CNVs of a defensive gene into the productive, but susceptible, crop varieties is a feasible breeding approach for enhancing plant resistance to herbivory and tolerance to abiotic stress.

The World Health Organization(WHO) in 2016 considered mHealth as: “the use of mobile wireless technologies including smart devices such as smartphones and smartwatches for public health” as an important resource for health services delivery and public health given their ease of use, broad reach and acceptance. WHO emphasizes the potential of this technology to increase access to health information, services and skills as well as promoting positive changes in health behaviors and management of diseases. In this regard, the capability of smartphones and smartwatches for m-health monitoring as well as verification of the patient the signal has become an important component of mHealth system. Most of the smartwatches could extract more than one bioelectrical signal therefore, therefore they provide suitable platform for extracting health data for e-monitoring. The existing approaches have not considered the integrity of data obtained from these smart devices. Therefore, it is important that the integrity of the collected data be verified continuously through user authentication. This could be done using any of the bioelectrical signals extracted and transmitted for e-monitoring. In this article, a smartwatch is used for extracting bioelectrical signal before decomposing the signal into sub-bands of Detail and Approximation Coefficient for user authentication. To select suitable features using biorthogonal wavelet decomposition of signal from a non-intrusive extraction, a detailed experiment is conducted extracting suitable statistical features from the bioelectrical signal from 30 subjects using different biorthogonal wavelet family. Ten features are extracted using Biorthogonal wavelet to decompose the signal into three levels of sub-band Detail and Approximation Coefficient and features extracted from each level the decomposed Detail and Approximation Coefficients. Comparison analysis is done after the classification of the extracted features based on the Equal Error Rate (EER). Using Neural Network (NN) classifier, Biorthogonal Wavelet Detail Coefficient Sub-band level 3 of bior1.1 achieved the best result of EER 13.80% with the fusion of the best sub-band three levels of bior1.1 achieving a better result of 12.42% EER.

Let R be a commutative ring with identity and m, n be positive integers. In this paper, we introduce the class of (m,n)-prime ideals which lies properly between the classes of prime and (m,n)-closed ideals. A proper ideal I of R is called (m,n)-prime if for a,b∈R, a^{m}b∈I implies either aⁿ∈I or b∈I. Several characterizations of this new class with many examples are given. Analougus to primary decomposition, we define the (m,n)-decomposition of ideals and show that every ideal in an n-Noetherian ring has an (m,n)-decomposition. Furthermore, the (m,n)-prime avoidance theorem is proved.

We report on metastable defects introduced in n-type 4H-SiC material by epithermal and fast neutron irradiation. The epithermal and fast neutron irradiation defects in 4H-SiC are much less explored compared to electron or proton irradiation induced defects. In addition to silicon vacancy (Vsi) and carbon antisite-carbon vacancy (CAV) complex, the neutron irradiation has introduced four deep level defects, all arising from the metastable defect, the M-center. The metastable deep level defects were investigated by deep level transient spectroscopy (DLTS), high-resolution Laplace DLTS (L-DLTS) and isothermal DLTS. The existence of the fourth deep level M4, recently observed in ion implanted 4H-SiC, has been additionally confirmed in neutron irradiated samples. The isothermal DLTS technique has been proven as a useful tool for studying the metastable defects.

The current work reports the upper bound of the state variable of the of the Pointwise Steady Fluid Flow Approximation (PSFFA) model of non-stationary M/Ek/1 queueing system.

The morphologically variable moss Trichostomum brachydontium is very common in south and west Europe, particularly under Mediterranean and Atlantic climates. A morphological study was conducted alongside a molecular phylogenetic study based on nr ITS and cp rbcL regions in order to assess if T. brachydontium is an exceptionally polymorphic species as evidenced by the number of described infraspecific taxa from the last century or, alternatively, if it includes more than one species, and if so, to find the valid name for them. Phylogenetic analyses of both nuclear and chloroplast datasets show that there are four well-supported clades. While the ITS based tree is in good agreement with the morphological data, there are a few inconsistencies with reference to the rbcL tree; this may be explained by incomplete lineage sorting or by hybridization. The morphological survey revealed well-defined discriminate differences between the four phylogenetic lineages. The taxonomic conclusions include the recognition of four species: T. brachydontium s.s., T. herzogii (a new name proposed for var. cuspidatum), T. littorale and T. meridionale (a new name proposed for var. densum). Lectotypes are designated for T. brachydontium and T. littorale. Our results underline the ongoing need of integrative studies to examine further the underestimated diversity of the T. brachydontium complex in other regions.

The onset and progression of human inflammatory joint diseases are strongly controlled by the activation of resident synovium/infrapatellar fat pad (IFP) pro-inflammatory and pain-transmitting signaling. We recently reported that intra-articularly injected IFP-derived Mesenchymal Stem/Stromal Cells (IFP-MSC) acquire a potent immunomodulatory phenotype and actively degrade Substance P (SP) via neutral endopeptidase CD10 (neprilysin). Our hypothesis is that IFP-MSC robust immunomodulatory therapeutic ef-fects are largely exerted via their CD10-bound exosomal secretome (IFP-MSC EXOs) by attenuating synoviocyte pro-inflammatory activation and articular cartilage degradation. Herein, IFP-MSC EXOs were isolated from CD10High- and CD10Low-expressing IFP-MSC cultures and their exosomal miRNA cargo was assessed using multiplex methods. Functionally, we interrogated the effect of CD10High and CD10Low EXOs on stimulated by inflammatory/fibrotic cues synoviocytes monocultures and cocultures with IFP-MSC de-rived chondropellets. Finally, CD10High EXOs were tested in vivo for their therapeutic capacity in an animal model of acute synovitis/fat pad fibrosis. Our results showed that CD10High and CD10Low EXOs possess distinct miRNA profiles. Reactome analysis of miRNAs highly present in exosomes showed their involvement in the regulation of six gene groups, particularly the immune system. Stimulated synoviocytes exposed to IFP-MSC EXOs demonstrated significantly reduced proliferation and altered inflammation-related molecular profiles compared to control stimulated synoviocytes. Importantly, CD10High EXOs treatment of stimulated chondropellets/synoviocytes cocultures indicated a significant chondroprotective effects. Therapeutically, CD10High EXOs treatment resulted in robust chondroprotective effects by retaining articular cartilage structure/composition and PRG4 (lubricin)-expressing cartilage cells in the animal model of acute synovitis/IFP fibrosis. Our study suggests that CD10High EXOs possess immuno-modulatory miRNA attributes with strong chondroprotective/anabolic effects for articular cartilage in vivo. The results could serve as a foundation for EXOs-based therapeutics for the resolution of detrimental aspects of immune-mediated inflammatory joint changes associated with conditions such as osteoarthritis (OA).

Zinc oxide is one of the most important semiconductor metal oxides and one of the most promising n-type materials, but its practical use is limited because of both its high thermal conductivity and its low electrical conductivity. Numerous studies have shown that doping with metals in ZnO structures leads to the modification of the band gap energy. In this work, Al-doped ZnO, Ni-doped ZnO, and undoped ZnO nanocrystalline powders were prepared by sol-gel method coupled with ultrasound irradiation. The doping concentration in ZnO was 1.0 at.% of Al and Ni. Influence of Al³⁺ and Ni²⁺ ions in the ZnO network are explored in this paper. X-ray Diffraction (XRD), Raman Spectroscopy, Nitrogen Adsorption (BET method), X-Ray Fluorescence (XRF) and Field Emission Scanning Electron Microscopy (FESEM) analyses demonstrated the incorporation of metal ions (aluminum and nickel) into the ZnO wurtzite structure. The crystallite size of the sample was decreased from 24.5 nm (ZnO) to 22.0 nm (ZnO-Al) and 21 nm (ZnO-Ni).

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

Rigid polyurethane foams were synthesized using a renewable polyol from the simple physical mixture of castor oil and crude glycerol. The effect of the catalyst and blowing agent in the foams properties was evaluated. The use of physical blowing agent (cyclopentane and n-pentane) allowed obtaining foams with smaller cells in comparison with the foams produced with a chemical blowing agent (water). The increase of water content caused a decrease of density, thermal conductivity, compressive strength and Young's modulus, which indicates that the increment of CO₂ production contributes to the formation of larger cells. Higher amount of catalyst in the foam formulations caused a slight density decrease and an increase small significance of thermal conductivity, compressive strength and Young's modulus values. These green foams presented properties that indicate a great potential to be used as thermal insulation, as density (23 - 41 kg m^-3), thermal conductivity (0.0128 – 0.0207 W m^-1 K^-1), compressive strength (45 - 188 kPa) and Young's modulus (3 - 28 kPa). These biofoams are also environmental friendly alternatives and can aggregate revenue to biodiesel industry, contributing for reduction of this fuel prices.

The present review revisits representative studies addressed to develop efficient carbon-based heterogeneous catalysts for two important reactions, namely, the production of hydrogen from formic acid and the hydrogenation of carbon dioxide to formic acid. The HCOOH-CO2 system is considered a promising couple for a hydrogen storage system that would be involved in an ideal carbon-neutral cycle. Significant advancements have been achieved in those catalysts designed to catalyze the dehydrogenation of formic acid under mild reaction conditions, while much effort is still needed to catalyze the challenging CO2 hydrogenation reaction. The design of carbon-based heterogeneous catalysts for these reactions encompasses both the modulation of the properties of the active phase (particle size, composition, and electronic properties), as well as the modification of the supports by means of incorporation of nitrogen functional groups. These approaches are herein summarized to provide a compilation of the strategies followed in recent studies to set the basis for a hydrogen storage system attained by the HCOOH-CO2 couple.

This work investigates the influence of ground albedo on the solar radiation obtained by surfaces mounted on fixed-tilt to south, one-axis, and two-axis systems. To do this, estimation of the solar radiation difference is performed by applying real albedo and zero albedo. This is done within Saudi Arabia, at 82 selected sites. Annual, seasonal, and monthly mean solar energy differences are computed as function of the site’s number, latitude, and local near-real ground albedo. The great variation in the ground-albedo values at the 82 sites (0.1 - 0.46) could be thought as having a significant effect on the solar radiation levels received on the 3 tracking modes. The analysis shows quite the opposite; a zero-albedo ground diminishes solar radiation levels by 1.43%, 3.50%, and 3.20%, respectively for the 3 modes. Therefore, in most solar engineering applications a ground albedo of 0.2 (considered as reference) can be used without losing accuracy. This is the main conclusion of the study, which must, however, be applied with caution in areas with snow cover, especially for mode-III tracking systems. In such situations the increase in solar radiation levels may be up to 15% (but ≈3.5% for mode-I and -II systems instead).

Intratumour heterogeneity is often associated with poor response to treatment and bad prognosis. In addition to constitutive genetic/epigenetic sources, phenotypic and functional heterogeneity can reflect cell plasticity due to changes in gene expression patterns induced by signals from the tumour microenvironment or other cells. Positive interactions between cancer clones can increase their fitness and contribute to tumour growth, resistance to drugs and metastasis. Consequently, understanding the pathways involved in such behaviours is of great significance for cancer treatment. To explore if and how genetically distant clones can synergistically enhance each other's metastatic potential, this study used three (two breast and one lung) cancer cell lines with different aggressiveness levels. We found that (i) the conditioned media from the breast and lung aggressive lines induce mesenchymal features and increase the migration and invasion potential of the poorly metastatic breast line, and (ii) in both cases, this interclonal communication is based on the same soluble factor – namely, the tumour growth factor TGF-β1. Furthermore, when the two breast lines are mixed and co-cultured, the invasive potential of both lines is enhanced, and this outcome is dependent on the recruitment of the less aggressive clone into expressing a malignant phenotype. Based on our findings, we propose a two-tier model whereby highly metastatic clones can recruit weakly metastatic clones into acquiring an invasive phenotype, which in turn augments the invasion ability of the former (i.e., a “help me help you” strategy) through shared proteases and/or ECM remodelling. We suggest that such synergistic cooperation can easily emerge via cross-talk involving metastatic clones able to constitutively secrete signalling molecules that induce and maintain their own malignant state (i.e., autocrine/cell-autonomous signalling) and clones that have the ability to respond to those signals (i.e., paracrine/non-cell-autonomous signalling) and express a metastatic phenotype. Taking into account the lack of therapies to directly affect the metastatic process, interfering with such cooperative behaviours that tumour cells engage in during the early steps in the metastatic cascade could provide an additional strategy to increase patient survival.

Cancer invasion through basement membranes represents the initial step of tumor dissemination and metastasis. However, little is known about how human cancer cells breach basement membranes. Here, we used a 3-dimensional in vitro invasion model consisting of cancer spheroids encapsulated by a basement membrane and embedded in 3D collagen gels to visualize the early events of cancer invasion by confocal microscopy and live-cell imaging. Human breast cancer cells generated large numbers of basement membrane perforations, or holes, of varying sizes that expanded over time during cell invasion. We used a wide variety of small molecule inhibitors to probe the mechanisms of basement membrane perforation and hole expansion. Protease inhibitor treatment (BB94), led to a 63% decrease in perforation size. After myosin II inhibition (blebbistatin), basement membrane perforation area decreased by only 15%. These treatments produced correspondingly decreased cellular breaching events. Interestingly, inhibition of actin polymerization dramatically decreased basement membrane perforation by 80% and blocked invasion. Our findings suggest that human cancer cells can primarily use proteolysis and actin polymerization to perforate the BM and to expand perforations for basement membrane breaching, with a relatively small contribution from myosin II contractility.

A fundamental question in biology is whether phenotypes can be predicted by ecological or genomic rules. At least five cases of convergent evolution of the crab-like body plan (with a wide and flattened shape, and a bent abdomen) are known in decapod crustaceans, and have, for over 140 years, been known as ‘carcinization’. The repeated loss of this body plan has been identified as ‘decarcinization’. In reviewing the field, we offer phylogenetic strategies to include poorly known groups, and direct evidence from fossils, that will resolve the history of crab evolution and the degree of phenotypic variation within crabs. Proposed ecological advantages of the crab body are summarized into a hypothesis of phenotypic integration suggesting correlated evolution of the carapace shape and abdomen. Our premise provides fertile ground for future studies of the genomic and developmental basis, and the predictability, of the crab-like body form.

Universities can do more to deliver against the Sustainable Development Goals (SDGs), working with faculty, staff and students as well as their wider stakeholder community and alumni body. They play a critical role in helping shape new ways for the world, educating global citizens and delivering knowledge and innovation into society – universities can be engines of societal transformation. Here, using a case study approach, different ways of strategizing sustainability in a university setting are explored with an example from the UK, Europe and USA. The first case is a public UK university that adopted enterprise and sustainability as its academic mission to secure differentiation in a disrupted and increasingly marketized global higher education sector which then became a source of inspiration for change in regional businesses and the local community. The second case study is a business sector-led sustainability-driven transformation working with a private university in Bulgaria to catalyze economic regeneration and social innovation. Finally, the case of Harvard’s Office for Sustainability engagement program is given to show how this approach connects faculty and students with institutional sustainability plans and external partners. Each case is a living lab, positioning sustainability as an intentional strategy. Leadership at all levels, and by students, was key to success in acting with purpose. Partnerships within and with universities can help accelerate delivery of the SDGs, with higher education making a fuller contribution to sustaining the economic, cultural and intellectual well-being of our global communities.

CSZM compounds were synthesized by dry chemistry route with 5, 10, and 15% dopant of Mg dopants in the Ce 0.8-2x Sm 0.2 Zrx Mgx O2-d, {x = 0.05, 0.1 &amp;0.15}. The newly investigated materials were physically, chemically, and electrochemically studied and have shown promising results. The CSZM was crystalized in a fluorite structure with a pure cubic phase in a space group Fm3m and cell parameter a = 5.401742 °A and theoretical density from 7.6 to 8.9 after firing in the air with a final temperature of 1400 °C. characterization of the structure and indexing of electrolyte materials were made after X-ray diffraction (XRD) testing. A Scanning electron microscope (SEM) morphological analysis was used to examine the microstructure details. Electronic impedance spectroscopy (EIS) measurements were achieved from 400 °C to 700 °C showing the highest value of conductivity of 1.0461 x 10+1 S/cm at 700 °C while the minimum value was 2.7329 x 10-2 S/cm at 400 °C and the total activation energy was found (Ea) 0.6865 eV under 5% H2/Ar.

Generating long-lived mucosal and systemic antibodies through respiratory immunization with protective antigens encapsulated in nanoscale biodegradable particles could potentially decrease or eliminate the incidence of many infectious diseases but requires incorporation of a suitable mucosal immunostimulant. We previously found that respiratory immunization with a model protein antigen (LPS-free OVA) encapsulated in PLGA 50:50 nanoparticles (~380 nm diameter) surface modified with complement peptide-derived immunostimulant 02 (CPDI-02; formerly EP67) through 2kDa PEG linkers increases mucosal and systemic OVA-specific memory T-cells with long-lived surface phenotypes in young, naïve female C57BL/6 mice. Here, we determined if respiratory immunization with LPS-free OVA encapsulated in similar PLGA 50:50 microparticles (~1 μm diameter) surface modified with CPDI-02 (CPDI-02-MP) increases long-term OVA-specific mucosal and systemic antibodies. We found that, compared to MP surface modified with inactive, scrambled scCPDI-02 (scCPDI-02-MP), intranasal administration of CPDI-02-MP in 50 μL sterile PBS greatly increased titers of short-term (14 days post-immunization) and long-term (90 days post-immunization) antibodies against encapsulated LPS-free OVA in nasal lavage fluids, bronchoalveolar lavage fluids, and sera of young, naïve female C57BL/6 mice. Thus, surface modification of biodegradable microparticles with CPDI-02 is likely to increase long-term mucosal and systemic antibodies against encapsulated protein antigen after respiratory and possibly other routes of mucosal immunization.

OPMDs (Oral Potentially Malignant Disorders) are a group of disorders affecting the oral mucosa that are characterized by aberrant cell proliferation and a higher risk of malignant transformation. Vitamin D (VitD) and its receptor (VDR) have been extensively studied for their potential contributions to the prevention and therapeutic management of a range of diseases and neoplastic conditions, including oral cancer. Observational studies suggest correlations between VitD deficiency and higher cancer risk, worse prognosis, and increased mortality rates. Interestingly, emerging data also reveals a link between VitD insufficiency and the onset or progression of OPMDs. Understanding the role of the VitD-VDR axis not only in established oral tumors but also in OPMDs might thus enable early detection and prevention of malignant transformation. With this article, we want to provide an overview of current knowledge about OPMDs and VitD, and investigate their potential association and ramifications for clinical management of OPMDs.

In the present work we revise and extend the Characteristic Crystallographic Element (CCE) norm, an algorithm used to simultaneously detect radial and orientational similarity of computer-generated structures with respect to specific reference crystals and local symmetries. Based on the identification of point group symmetry elements, the CCE descriptor is able to gauge local structure with high precision and finely distinguish between competing morphologies. As test cases we use computer-generated monomeric and polymer systems of spherical particles interacting with the hard-sphere and square-well attractive potentials. We demonstrate that the CCE norm is able to detect and differentiate, between others, among: hexagonal close packed (HCP), face centered cubic (FCC), hexagonal (HEX) and body centered cubic (BCC) crystals as well as non-crystallographic fivefold (FIV) local symmetry in bulk 3-D systems; triangular (TRI), square (SQU) and honeycomb (HON) crystals, as well as pentagonal (PEN) local symmetry in thin films of one-layer thickness (2-D systems). The descriptor is general and can be applied to identify the symmetry elements of any point group for arbitrary atomic or particulate system in two or three dimensions, in the bulk or under confinement.

The carbonized elastomer-based composites (CECs) possess a number of attractive features in terms of thermomechanical and electromechanical performance, durability in aggressive media and facile net-shape formability, but their relatively low ductility and strength limit their suitability for structural engineering applications. Prospective applications such as structural elements of MEMS can be envisaged, since smaller principal dimensions reduce the susceptibility of components to residual stress accumulation during carbonization, and to brittle fracture in general. We report the results of operando in-SEM study of micro-deformation and fracture behavior of CECs based on NBR elastomeric matrices filled with carbon and silicon carbide. Nanostructured carbon composite materials were manufactured via compounding of elastomeric substance with carbon and SiC fillers using mixing rolling mill, vulcanization, and low-temperature carbonization. Double Edge Notched Tensile (DENT) specimens of vulcanized and carbonized elastomeric composites were subjected to in situ tensile testing in the chamber of the scanning electron microscope (SEM) Tescan Vega 3 using Deben Microtest 1 kN Tensile Stage. The series of acquired SEM images were analyzed by means of Digital Image Correlation (DIC) using Ncorr open source software to map the spatial distribution of strain. These maps were correlated with Finite Element Modelling (FEM) simulations to refine the values of elastic moduli. Besides, the elastic moduli were derived from unloading curve nanoindentation hardness measurements carried out using NanoScan-4D tester and interpreted using the Oliver-Pharr method. Carbonization causes significant increase of elastic moduli from 0.86 ± 0.07 to 14.12 ± 1.20 GPa for the composite with graphite and carbon black fillers. Nanoindentation measurements yield somewhat lower values, namely, 0.25 ± 0.02 GPa and 9.83 ± 1.10 GPa before and after carbonization respectively. The analysis of fractography images suggests that crack initiation, growth and propagation may occur both at the notch stress concentrator and relatively far from the notch. Possible causes of such response are discussed, namely, (1) residual stresses introduced by processing; (2) shape and size of fillers; and (3) the emanation and accumulation of gases in composites during carbonization.

Limited studies have shown that exposure to arsenic is associated with serum vitamin D levels, but the results are still inconsistent. A cross-sectional study of 762 participants was conducted in Wenshui Country, Shanxi Province, which was identified as an area of water-borne arsenicosis. The results showed positive relationship between arsenic species (iAs, MMA, DMA) and serum 25(OH)D. Binary logistic regression analysis showed that the significant increases of 0.4% and 0.6% in the risk of vitamin D excess for every 1-unit increment in the Box-Cox transformed urinary tAs and DMA, respectively. After stratifying populations based on arsenic methylation metabolic capacity, each one-unit increase in the Box-Cox transformed tAs level was associated with increases of 0.064 (95%CI: 0.032 to 0.096) in serum 25(OH)D in the populations with iAs% above the median. In the populations with skin hyperkeratosis, urinary iAs was positively associated with serum 25(OH)D (β=0.592, 95%CI: 0.041 to 1.143). Overall, our findings support the positive relationship between urinary arsenic and serum 25(OH)D.

Soil-borne Trichoderma spp. have been extensively studied for their biocontrol activities against pathogens and growth promotion ability with plants. However, the beneficial effect of Trichoderma on inducing resistance against insect herbivores has been considered only recently. Among diverse Trichoderma species, consistent with previous reports, we showed that root colonization by T. virens triggered induced systemic resistance (ISR) to leaf-infecting fungal pathogens. Whether T. virens induces ISR to insect pests has not been tested before. In this study, we investigated whether T. virens affects jasmonic acid (JA) biosynthesis and defense against fall armyworm (FAW) and western corn rootworm (WCR). Unexpectedly, the results showed that T. virens colonization of maize seedlings grown in autoclaved soil suppressed wound-induced production of JA, resulting in reduced resistance to FAW. Similarly, the bacterial endophyte Pseudomonas chlororaphis 30-84 suppressed systemic resistance to FAW due to reduced JA. Further comparative analyses of the systemic effects of these endophytes when applied into sterile or non-sterile field soil showed that both T. virens and P. chlororaphis 30-84 triggered ISR against hemibiotrophic fungal pathogen Colletotrichum graminicola in both soil conditions, but only suppressed resistance to FAW in sterile soil. In contrast to the effect on FAW defense, T. virens colonization of maize roots suppressed WCR larvae survival and weight gain. This is the first report suggesting the potential role of T. virens as a biocontrol agent against WCR.

The Rosetta software suite for macromolecular modeling, docking, and design is widely used in pharmaceutical, industrial, academic, non-profit, and government laboratories. Considering its broad modeling capabilities, Rosetta consistently ranks highly when compared to other leading methods created for highly specialized protein modeling and design tasks. Developed for over two decades by a global community of scientists at more than 60 institutions, Rosetta has undergone multiple refactorings, and now comprises over three million lines of code. Here we discuss the methods developed in the last five years, involving the latest protocols for structure prediction, protein–protein and protein–small molecule docking, protein structure and interface design, loop modeling, the incorporation of various types of experimental data, and modeling of peptides, antibodies and other proteins in the immune system, nucleic acids, non-standard amino acids, carbohydrates, and membrane proteins. We briefly discuss improvements to the energy function, user interfaces, and usability of the ­­software. Rosetta is available at www.rosettacommons.org.

Study Objectives: The aim of this study is to explore the association between serum 25-hydroxyvitamin D [25(OH)D] levels, a marker of Vitamin D status, and excessive daytime sleepiness (EDS), expressed as increased scores of Epworth Sleepiness Scale (ESS), in a group of prospectively enrolled patients with obstructive sleep apnea (OSA). Methods: Newly diagnosed patients with OSA, divided into two groups, those with EDS (ESS>10) and those without EDS (ESS

Pulmonary infections with Mycobacterium avium occur in susceptible individuals following exposure to the bacterium in the environment, where it often persists in biofilms. Many methods have been used to generate biofilms of M. avium, and it is unknown whether different approaches generate similar structures and cell phenotypes. To make a parallel comparison of in vitro biofilm ultrastructure, extracellular matrix (ECM) composition, and drug susceptibility of biofilm resident bacteria, we used two published methods to generate M. avium biofilms: four week incubation in M63 medium or 24 hour exposure to dithiothreitol (DTT). Scanning electron microscopy revealed differences in biofilm ultrastructure between the two methods, including variation in appearance of ECM materials and morphology of resident cells, while light microscopy and staining with calcofluor white indicated that both biofilms contained polysaccharides characteristic of cellulose. Measuring susceptibility of biofilms to degradation by enzymes suggested differences in structurally important ECM molecules, with DTT biofilms having important protein and, to a lesser extent, cellulose components, and M63 biofilms having moderate protein, cellulose, and DNA components. Both biofilms conferred resistance to the bactericidal effects of amikacin and clarithromycin, with resident cells being killed at &gt;10-fold lower rates than planktonic cells at almost all concentrations. Though these comparisons indicate differences in biofilm responses by M. avium under differing conditions, they also suggest common features of biofilm formation including cellulose production and antimicrobial resistance.

The topological index is a numerical quantity based on the characteristics of various invariants or molecular graph. For ease of discussion, these indices are classified according to their logical derivation from topological invariants rather than their temporal development. Degree based topological indices depends upon the degree of vertices. This paper computes degree based topological indices of Bismuth Tri-Iodide chains and sheets with the help of M-polynomial.

The current study focused on reviewing the rapid growing of using magnetic water in different fields of science and measure the influence of several intensities of magnetization on the chemical and electrical properties of tap water treated by reverse osmosis. The work includes circulation of water for 24 h. in magnetic fields of intensity 500, 1000, 1500, and 2000 G. The magnetization of water causes increasing some positive and negative ions in water such as (Mg, K, Na, Cl¯, Alkaline and SiO₂) and decreasing some positive and negative ions (Ca and SO₃). In the near future, the application of concepts of sustainability development in civil engineering have the to produce structures in harmony with these concepts through using of high-performance materials with less impacts on the environmental and have low cost. The main application of using magnetic water is improvement the geotechnical properties of soil through precipitation of calcite which increases the bond between soil particles and then strength of soil.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

Swarm intelligence (SI) methods are nature-inspired metaheuristics for global optimization that exploit a coordinated stochastic search strategy by a group of agents. Particle Swarm Optimization (PSO) is an established SI method that has been applied successfully to the optimization of rugged high-dimensional likelihood functions, a problem that presents the main bottleneck across a variety of gravitational wave (GW) data analysis challenges. We present results from a first application of PSO to one of the most difficult of these challenges, namely, the search for Extreme Mass Ratio Inspiral (EMRI) in data from future spaceborne GW detectors such as LISA, Taiji, or Tianqin. We use the standard Generalized Likelihood Ratio Test formalism, with minimal use of restrictive approximations, to search 6 months of simulated LISA data and quantify the search depth, in signal-to-noise ratio (SNR), and breadth, in the ranges of the EMRI parameters, that PSO can handle. Our results demonstrate that a PSO-based EMRI search is successful over a search region that is in the ballpark of the one that current hierarchical schemes can identify. Directions for future improvements, including computational bottlenecks to be overcome, are identified.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In this study, based on a new quantum integral identity, the authors establish some quantum estimates of Hermite-Hadamard type inequalities for convex functions. These results generalize and improve some known results given in literatures.

Insecticidal toxins from Bacillus thuringiensis (Bt) are valuable tools for pest management worldwide, contributing to the management of human disease insect vectors and phytophagous insect pests of agriculture and forestry. Here, we report the effects of dual and triple Bt toxins expressed in transgenic cotton cultivars on the fitness and demographic performance of Helicoverpa zea (Boddie), a noctuid pest known as cotton bollworm and corn earworm. Life-history traits were determined for individuals of three field populations from a region where H. zea overwintering is likely. Triple-gene Bt cotton cultivars expressing Cry and Vip3Aa toxins killed 100% of the larvae in all populations tested. In contrast, dual-gene Bt cotton expressing Cry1Ac+Cry1F and Cry1Ac+Cry2Ab2 allowed population growth with the intrinsic rate of population growth (rm) 38% lower than on non-Bt cotton. The insects feeding on Bt cotton plants expressing Cry1Ac+Cry2Ab2, Cry1Ac+Cry1F, or Cry1Ab+Cry2Ae exhibited reduced larval weight, survival rate, and increased development time. Additionally, fitness parameters varied significantly among the insect populations, even on non-Bt cotton plants, likely because of their different genetic background and/or previous Bt toxin exposure. This is the first report of the comparative fitness of H. zea field populations on dual-gene Bt cotton after the recent reports of field resistance to certain Bt toxins. These results document the population growth rates of H. zea from an agricultural landscape with 100% Bt cotton cultivars. Our results will help to refine models designed to predict resistance evolution and improve insect resistance management for Bt crops.

Concrete is more stable than filler as a false roof in a downward approach type infill quarry, but the mechanical model of a concrete false roof is not clear. As a result, there has been limited application. Therefore, it is necessary to establish the mechanical model of a concrete artificial false roof to enhance the stability of the downward approach infill quarry. This paper combines theoretical analysis, model derivation, finite element analysis and field application methods. Firstly, the basic assumptions of thin plate theory and elasticity mechanics are used as the premise to establish the differential equations of the deflection curve of the concrete thin plate false roof. Then, the three types of bending moment generation of the concrete thin plate false roof are explored. Secondly, the relationship between the location of dangerous surface and dangerous point in hard-supported weak-slab structure and soft-supported weak-slab structure is analyzed, and the type of uniform load and calculation model of concrete thin-slab false roof are improved. Finally, according to the established mechanical model of thin slab false roof, finite element analysis and field application were carried out. The results show that there are three types of deflection curve differential equations in the concrete thin slab false roof perpendicular to the strike, and three extreme points exist in the middle section of the thin slab and on both sides of the surrounding rock. The hazardous surface of the hard-supported weak-slab structure is present at the intersection of the encircling rock and the thin-slab fake ceiling, with the perilous point situated on the top of this surface. The hazardous surface of the soft-supported weak-slab structure can be found in the centre section of the thin-slab fake ceiling, with the perilous point being located at the bottom of this surface. Moreover, the damage mode for both structures is that of maximum tensile stress damage. Upon conducting a finite element analysis, the results indicate that the concrete's maximum tensile stress is significantly high.

Practical applications of CsPbX3 nanocrystals (NCs) are limited by their poor stability. The formation of heterojunction between CsPbX3 NCs and oxides is an effective means to protect perovskite from polar solvents and other external factors. Significantly improving the stability and photocatalytic properties of the core/shell perovskite is very important for its application in photoelectric and photocatalytic technology. Here, we report the synthesis of asymmetrical CsPbBr3/TiO2 core-shell heterostructure NCs at single particle level by hot injection liquid phase synthesis and sol-gel method, where each CsPbBr3 NCs is partially covered by titanium dioxide. It is shown that the type II arrangement is generated at the heterogeneous interface, which greatly facilitates the separation of electron-hole pairs and increases the carrier transport efficiency. More crucial, due to the protection of titanium dioxide shell, the product has higher long-term stability in humid air compared with bare CsPbBr3 NCs. The asymmetrical core-shell heterostructure prepared in this study not only improves the stability of CsPbX3 NCs, but also provides some ideas for optoelectronic device applications and TiO2-based photocatalysts.

Traceability is the ability to determine the path of a product from purchase to consumption to determine when and where it originated. This paper aimed to determine the factors that influence fishers’ decision-making to participate in tuna traceability program, it also explores the determinants of fish catch for small-scale fishers and the feasibility of implementing tuna traceability in the Davao Gulf, Philippines. The result of the interview showed that the significant factors that highly affected the decision-making of fishers in implementating tuna traceability program: boat capacity, fishing hours and communication of fishers (P≤0.05). Household size, years in community, fishing hours, volume of fish sold, and the fishers' communication in the fishing ground (P≤0.05) were other factors that determined the daily catch of the fishers. The results of this study showed that fishers from the Davao Gulf were willing to be part of traceability program that would sustain and increase the value of their fish catch. Moreover, communication was shown to be critically needed in such programs adjusting it for the fish catch to remain fresh or of good quality. Our study will help in deterring and mitigating illegal, unregulated and unreported fishing (IUU) through fish catch traceability.