Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

Maternal obesity and gestational diabetes predispose to metabolic disturbances in the next generation. Moreover, the lactation phase also stands as critical for metabolic programming. Nevertheless, the precise mechanisms originating these changes remain unclear. Here we investigate the consequences of maternal diet lipid-rich diet during gestation and lactation, and its impact on metabolism and behavior in the offspring. Two experimental groups of Wistar female rats were used: a control group (NC) that fed a standard diet during gestation and lactation periods and an overnutrition group that fed a high-fat diet (HF, 60% lipid-rich) during the same phases. Offspring were analyzed at postnatal days 21, 28, and 2 months-old (PD21, PD28, PD60) for metabolic profile (weight, fasting glycemia insulin sensitivity, glucose tolerance) and euthanized for brain collection to evaluate by western blot markers of synaptic dynamics, metabolism and inflammation in the hypothalamus, hippocampus and prefrontal cortex. At 2 months-old, behavioral tests for anxiety, stress, cognition, and food habits were conducted. We observe that female offspring born from HF mothers exhibited increased weight gain and decreased glucose tolerance that attenuates with age. In offspring males, weight gain increased at P21 and worsened with age, while glucose tolerance remained unchanged. Offspring of HF mothers exhibited elevated levels of anxiety and stress during behavioral tests, displaying decreased predisposition for curiosity compared to the NC group. In addition, offspring from mothers with HF showed increased food consumption and a lower tendency towards food-related aggression. We conclude that exposure to HF diet during pregnancy and lactation induces dysmetabolism in the offspring accompanied by heightened stress and anxiety. There was sexual dimorphism in metabolic traits but not behavioral phenotypes.

Olefin metathesis of ethyl linoleate (EL) was investigated under different conditions of substrate amount, temperature, and catalyst. Second-generation Grubbs catalyst (G2) was used in experiments at 20 and 50 ºC for 24 and 48h, whereas first-generation Grubbs catalyst (G1) and [RuCl₂(PPh₃)₂perhydroazepine] (LN) were used in experiments at 50 ºC for 24h, with the latter also being investigated in the presence or absence of SnCl₂ as co-catalyst. Catalytic products were analyzed for GC-MS and discussed in terms of relative percent of the metathesis products. With G2 as catalyst, GC-MS chromatograms were similar in all the amounts of EL investigated at 50 ºC for 24h, except for ethyl hexadec-9-enoate (compound K), which was obtained with different percentage as a function of EL amount (55% for 2 and 5 mL and 65% for 8 mL). An α,ω-dicarboxylic acid with m/z = 444.00 (compound L) was produced from the experiments at 50 ºC for 24h with similar percentage as a function of EL amount. However, the relative percentage of L changed with the increase of EL volume in the experiments at 20 ºC (ca. 18, 27, and 28%, with 2, 5, and 8 mL of EL, respectively). The olefin metathesis of EL conducted by G1 reached lower selectivity than that conducted by G2 for 24h at 50 ºC. Several intense peaks reached with G1 were similar to those obtained with G2, in addition to new peaks of medium intensity. Compound L showed higher m/z, similar to that presented with G2, but with lower relative proportion in the mixture. LN was inert for olefin metathesis of EL; however, it was activated in the presence of SnCl₂ at 50 ºC for 24h. Different compounds and selectivity as a function of the catalyst type and reaction conditions were obtained.

The study of phytotherapy in dentistry is relevant due to the low occurrence of research in the treatment of oral pathologies, such as caries and periodontal disease. Thus, the aim of this research was to characterize the chemical composition of extracts from the leaves of Couroupita guianensis Aubl, including toxicological evaluation and the antioxidant and antimicrobial potential against Staphylococcus aureus, Streptococcus mutans and Candida albicans. Three extracts were prepared using assisted ultrasound, originating the Crude Ultrasound Extract (CUE) and Soxhlet apparatus, originating the Crude Soxhlet Extract (CSE) and the Ethanol Soxhlet Extract (ESE). In the analysis of the chemical composition, the presence of flavonoids, tannins and saponins were detected. LC-DAD analysis revealed the presence of caffeic acid, sinapic acid, rutin, quercetin, luteolin, kaempferol and apigenin in all extracts. In the GC-MS analysis, stigmasterol and β-sitosterol were identified in CUE and CSE. The antioxidant potentials, determined by the DPPH• and ABTS•+ methods, the ESE showed higher antioxidant activity (2.98 ± 0.96 and 4.93 ± 0.90, respectively). In the evaluation of toxicity, the CUE 50µg/mL and the ESE 50 µg/mL presented growth stimulation of Allium cepa roots. At a concentration of 750µg/mL, all extracts inhibited root growth. None of the extracts showed toxicity against Artemia salina. Antibacterial action was detected in all extracts, mainly against the microorganisms S. aureus and S. mutans; however, the antifungal action against C. albicans was not detected. From the results, the extracts of C. guianensis have therapeutic potential for use in the control of microorganisms in the oral microbiota.

Objectives Bone fractures are very common diseases, which can be caused by impact injuries or physiological disorders. Thus, the present review aimed to study the use of medicinal plants in the healing mechanism of bone fractures. Evidence acquisition Through research in the PubMed, Google Academic, and Scielo databases, this article reviews 11 ethnopharmacological studies and 34 preclinical studies on the biological actions of different plants in bone fracture healing mechanism. Results Indian tribes have highlighted in the plants ethnopharmacological study for various diseases, including bone fractures. However, despite the large citations of traditional use, technical-scientific studies are still scarce in the literature. Chenopodium ambrosioides, Piper sarmentosum, quadrangular Cissus, Ricinus communis and Radix salvia miltiorrhiza plants were the most studied in the literature regarding their osteogenic, angiogenic, anti-inflammatory and remodeling effects, acting on bone receptors, stimulating bone metabolism, increasing minerals uptake, and assisting in free radicals breakdown. Conclusion Thus, the medicinal plants use is promising in the field of bone regeneration, as well as being alternative when conventional therapies are unfeasible, increasing herbal medicines demand and popularity.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

Respiratory syncytial virus (RSV) infection is a major cause of severe respiratory disease in infants and young children worldwide. Two vaccines targeting the elderly and pregnant women have been recently approved employing the prefusion form of the RSV-fusion protein (F). However, there are currently no vaccines for infants. Studies have shown a fusion-inactive prefusogenic F form is significantly more immunogenic and produces higher antibody titers to both the prefusion and postfusion structures of the F protein. Here we have developed RSV virus-like particles (RSV-VLPs) consisting of prefusogenic F, RSV glycoprotein and matrix proteins, produced them using the baculovirus expression system, and studied their protective efficacy in Balb/c mice. Morphology and successful assembly of VLPs were confirmed by transmission electron microscopy and western blot. Mice immunized with VLPs developed high levels of serum IgG and neutralizing antibodies as compared with mice immunized with inactivated virus. The VLP vaccine also induced higher levels of IFNγ and IL4, elicited limited proliferation of CD4+ and CD8+ T cells but higher cytotoxic-T-lymphocyte responses. VLP immunization abolished lung pathology in the mice after RSV challenge. Overall, our results indicate that RSV-VLPs consisting of prefusogenic F, glycoprotein and matrix proteins are a potential vaccine candidate against RSV.

Titania is one of the most comprehensively studied nanostructures due to its widespread applications in production of catalytic, gas- sensing and corrosion- resistance materials [1]. M-polynomial of nanotubes has been vastly investigated as it produces many degree-based topological indices which are numerical parameters capturing structural and chemical properties. These indices are used in the development of quantitative structure-activity relationships (QSARs) in which the biological activity and other properties of molecules are correlated with their structure like boiling point, stability, strain energy etc of chemical compounds. In this paper, we determine M-polynomials of single-walled titanium (SW TiO2) nanotubes and recover important topological degree based indices of them to theoretically judge these nanotubes. We also use Maple to plot surfaces associated to different types of single-walled titanium (SW TiO2) nanotubes.

Melon (Cucumis melo L.) a member of family Cucurbitaceae is extensively cultivated for its fleshy fruits. Based on the specific agro-climatic zones of cultivation as well as concerning the regional preferences, melon displays significant variability phenotypic and biochemical attributes. Below, an effort is put forth to considerably evaluate the scope of achievements while in the growth as well as the enactment of melon breeding programs by employing the newest solutions. Melon breeding has achieved critical milestones throughout the previous century, and we hope this trend will go on to persist down the road. However, studies have to determine new genetic information for genes associated with the challenges imposed by climate change. The identification of valuable hereditary and also metabolic variability in the form of landraces and melon wild relatives will be useful for harvest diversification and also for the broadening of the cultivated melon genetic base. Whereas, considerable information on genomics, and melon metabolomics, is beneficial for dissecting the basis of the inheritance of important traits and their impact on the former characteristics. Overall, we hope the manuscript is going to serve as a crucial resource for the melon breeders.

We investigate alternative candidates to dark energy that can explain the current state of the universe in the framework of the generalized teleparallel theory of gravity f(T ) where T denotes the torsion scalar. To achieve this, we carried out a series of reconstruction taking into account to the ordinary and entropy-corrected versions of the holographic and new agegraphic dark energy models. These models used as alternative to dark energy in the literature in order describe the current state of our universe. It is remarked that the models reconstructed indicates behaviors like phantom or quintessence models. Furthermore, we also generated the EoS parameters associated to entropy-corrected models and we observed a transition phase between quintessence state and phantom state as showed by recent observational data. We also investigated on the stability theses models and we created the {r − s}. The behavior of certains physical parameters as speed of sound and the Statefinder parameters are compatible with current observational data.

Cariogenic oral biofilms cause a considerable amount of recurrent dental caries around composite restorations every year, resulting in unprosperous oral health status and expensive restorative treatment for many patients. Quaternary ammonium monomers that can be copolymerized with the current dental resin systems have been increasingly explored for modulation of dental plaque biofilm growth over dental composite surfaces. Here, we investigated the effect of bis(2-methacryloyloxyethyl) dimethylammonium bromide (QADM), against human overlying mature oral biofilms grown intra-orally in human participants for 7 and 14 days, for the first time. Seventeen volunteers wore palatal devices containing composite specimens containing 10% by mass of QADM or a control composite without QADM. After 7 and 14 days, the adherent biofilms were collected for determination of bacterial counts via colony-forming unit (CFU) counts. The biofilm viability, chronological changes, and percentage coverage were also determined by live/dead staining. QADM composites caused a significant inhibition of S. mutans biofilm formation for up to seven days. No difference in the CFU values were found for the 14-day period. Our findings suggest that (1) QADM composite was successful in inhibiting 1-3 day biofilms in the oral environment in vivo; (2) QADM significantly reduced the portion of S.mutans group in a time course where patients at high risk of caries would develop initial enamel carious lesions; and (3) stronger antibiofilm activity is required for the control of mature long-term cariogenic biofilms. These results provide a perspective on the value of integrating bioactive restorative materials with traditional caries management approaches into clinical practice. Contact-killing strategies via dental materials aiming to prevent or at least reduce high numbers of cariogenic bacteria seem to be a promising approach in patients at high risk of recurrence of dental caries around composites.

: The objective of this study was to obtain different dry matter contents and proportions of mel-on plant biomass for silage making. A completely randomized design was adopted with a facto-rial scheme (3 x 2) in four replications. The first factor corresponded to three mixtures of melon biomass on as fed basis (AF) of plant (branch + leaf) and fruit (harvested melon) as follows: 100% plant, 90% plant + 10% fruit, and 100% fruit. The other factor corresponded to the ensiled materi-al with fresh and dehydrated melon plant biomass (40% DM) which was dried in the field, after harvest. Silages with partial dehydration of the biomass available after fruit harvest with 0% and 10% fruit showed the greatest DM values: 297 and 293 g/kg DM, respectively. Silages with 0, 100 and 10% fruit showed medium LAB populations: 5.79, 5.14 and 4.58 logs CFU/g, respectively. Higher concentrations of acetic acid contents were observed in silages with 0 and 10% fresh fruit, which were 14.9 and 14.1 g/kg DM, respectively. Silages with 0% and 100% of dehydrated fruit showed better results for the indicators of good-quality silage. Dehydration improves the fer-mentative profile and quality of the melon silage.

This paper presents a concise mathematical framework for investigating both feed-forward and backward process, during the training to learn model weights, of an artificial neural network (ANN). Inspired from the idea of the two-step rule for backpropagation, we define a notion of F_adjoint which is aimed at a better description of the backpropagation algorithm. In particular, by introducing the notions of F-propagation and F-adjoint through a deep neural network architecture, the backpropagation associated to a cost/loss function is proven to be completely characterized by the F-adjoint of the corresponding F-propagation relatively to the partial derivative, with respect to the inputs, of the cost function.

In this work, we study the existence of strange star in the background of f(T,T) gravity in the Einstein spacetime geometry, where T is the torsion tensor and T is the trace of the energy-momentum tensor. The equations of motion are derived for anisotropic pressure within the spherically symmetric strange star. We explore the physical features like energy conditions, mass-radius relations, modified TOV equations, principal of causality, adiabatic index, redshift and stability analysis of our model. These features are realistic and appealing to further investigation of properties of compact objects in f(T,T) gravity as well as their observational signatures.

The current study aimed to: i) Monitor levels of PM₁₀, at Shebika, Haram, Masfala, Azizia, Awali and Mina in Makkah city, KSA during the period of 01 Shawwal 1436H – 27 Rabi Al-Awwal 1437H, by using LVS instruments; and; 2) assess health risk (non-cancer and cancer risks) on humans (children and adult) exposed to PM₁₀ in ambient air of Makkah city.The results showed that: the high PM₁₀ levels were found in Haram site, while the lower levels were found in Awali site. These levels were lower than that set for PM₁₀ by PME (Daily limit of 340 µg/m³). Vehicles emissions and constructions sources may be the main source of PM₁₀ levels in Makkah city. The human health risk assessments showed that: the daily exposure doses of PM₁₀ were ranked in the order: D_ing > D_dermal > D_inh for children and adult in Makkah city. Ingestion of PM₁₀ particles was the main exposure pathway for both children and adults. The HIs and cancer risk values were within the safe level, indicating that (non-carcinogenic and carcinogenic) risks for humans exposed to PM₁₀ in Makkah city were negligible.

It has been proven that in standard Einstein gravity, exotic matter (i.e. matter violating the point-wise and averaged weak and null energy conditions) is required to stabilize traversable wormholes. Quantum field theory permits these violations due to the quantum coherent effects found in any quantum field . Even reasonable classical scalar fields violate the energy conditions. In the case of the Casimir effect and squeezed vacuum states, these violations have been experimentally proven. It is advantageous to investigate methods of minimizing the use of exotic matter. One such area of interest is extended theories of Einstein gravity. It has been claimed that in some extended theories, stable traversable wormholes solutions can be found without the use of exotic matter. There are many extended theories of gravity and in this review paper we first explore f(R) theories and then explore some wormhole solutions in f(R) theories including Lovelock gravity.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Discovery of microRNAs (miRNAs) twenty years ago, has advocated a new era of “Molecular Genetics”. About 2000 miRNAs are present, that regulate one third of the genome. MiRNAs dysregulated expression may contribute to several diseases including tumor growth. Their presence in body fluids, reflecting levels alteration in various cancers, merit circulating miRNAs as the “next generation biomarkers” for early stages tumor diagnosis and/or prognosis. Herein, we performed a comprehensive literature search focusing on the origin, biosynthesis and role of miRNAs and summarized the foremost studies centering on miRs value as non-invasive biomarkers in different non-communicable diseases, including various cancer types. Moreover, during chemotherapy many miRNAs were linked to multidrug resistance, via modulating numerous biological processes and/or pathways that will be highlighted as well.

In this paper, we implement a new method binary Particle Swarm Optimization (PSO) for solving the kidney exchange problem, which will improve the future decisions of kidney exchange programs. Because using a kidney exchange, we can help incompatible patient-donor couples to swap donors to receive a compatible kidney. Kidney paired donation programs provide an innovative approach for increasing the number of available kidneys. Further, we implementing binary particle swarm optimization in parallel with MATLAB with one, two, three and four threads and from the computations point of view, the authors compare the performance to reduce the running time for kidney exchange to match patients as fast as possible to help clinicians. Moreover, implementing binary particle swarm optimization in solving the kidney exchange problem is an effective method. The obtained results indicate that binary PSO outperforms other stochastic-based methods such as genetic algorithm, ant lion optimization, and efficient the number of resulting exchanges.

Abstract: As a low-input crop, Miscanthus offers numerous advantages that, in addition to agricultural applications, permits its exploitation for energy, fuel, and material production. Depending on the Miscanthus genotype, season, and harvest time as well as plant component (leaf versus stem), correlations between structure and properties of the corresponding isolated lignins differ. Here, a comparative study is presented between lignins isolated from M. x giganteus, M. sinensis, M. robustus and M. nagara using a catalyst-free organosolv pulping process. The lignins from different plant constituents are also compared regarding their similarities and differences regarding monolignol ratio and important linkages. Results showed that the plant genotype has the weakest influence on monolignol content and interunit linkages. In contrast, structural differences are more significant among lignins of different harvest time and/or season. Analyses were performed using fast and simple methods such as nuclear magnetic resonance (NMR) spectroscopy. Data was assigned to four different linkages (A: b-O-4 linkage, B: phenylcoumaran, C: resinol, D: b-unsaturated ester). In conclusion, A content is particularly high in leaf-derived lignins at just under 70 % and significantly lower in stem and mixture lignins at around 60 % and almost 65 %. The second most common linkage pattern is D in all isolated lignins, the proportion of which is also strongly dependent on the crop portion. Both stem and mixture lignins, have a relatively high share of approximately 20 % or more (maximum is M. sinensis Sin2 with over 30 %). In the leaf-derived lignins, the proportions are significantly lower on average. Stem samples should be chosen if the highest possible lignin content is desired, specifically from the M. x giganteus genotype, which revealed lignin contents up to 27 %. Due to the better frost resistance and higher stem stability, M. nagara offers some advantages compared to M. x giganteus. Miscanthus crops are shown to be very attractive lignocellulose feedstock (LCF) for second generation biorefineries and lignin generation in Europe.

Nitric oxide (NO) is involved in physiological processes, including vasodilatation, wound healing and antibacterial activities. As NO is a free radical, designing drugs to generate therapeutic amounts of NO in controlled spatial and time manners is still a challenge. In this study, the NO donor S-nitrosoglutathione (GSNO) was incorporated into the thermoresponsive Pluronic F-127 (PL) - chitosan (CS) hydrogel, with an easy and economically feasible methodology. CS is a polysaccharide with known antimicrobial properties. Scanning electron microscopy, rheology and differential scanning calorimetry techniques were used for hydrogel characterization. The results demonstrated that the hydrogel has a smooth surface, thermoresponsive behavior and good mechanical stability. The kinetics of NO release and GSNO diffusion from GSNO-containing PL/CS hydrogel demonstrated a sustained NO/GSNO release, in concentrations suitable for biomedical applications. The GSNO-PL/CS hydrogel demonstrated a concentration-dependent toxicity to Vero cells, and antimicrobial activity to Pseudomonas aeruginosa (minimum inhibitory concentration and minimum bactericidal concentration values of 0.5 µg·mL^-1 of hydrogel, which corresponds to 1 mmol·L^-1 of GSNO). Interestingly, the concentration range in which the NO-releasing hydrogel demonstrated an antibacterial effect was not found to be toxic to the Vero mammalian cell. Thus, the GSNO-PL/CS hydrogel is a suitable biomaterial for topical NO delivery applications.

Sphingolipids play an important role in the development of diabetes both type 1 and type 2 diabetes as well as in the development of both micro- and macro-vascular complications. Several reviews have been published concerning the role of sphingolipids in diabetes but most of the emphasis has been on the possible mechanisms by which sphingolipids, mainly ceramides, contribute to the development of diabetes. Research on circulating levels of the different classes of sphingolipids in serum and in lipoproteins and their importance as biomarkers to predict not only the development of diabetes but also of its complications has only recently emerged and it is still in its infancy. This review summarizes the previously published literature concerning sphingolipid-mediated mechanisms involved in the development of diabetes and its complications focusing on how circulating plasma sphingolipid levels and the relative content carried by the different lipoproteins may impact their role as possible biomarkers both in the development of diabetes and mainly in the development of diabetic complications. Further studies in this field may open new therapeutic avenues to prevent or arrest/reduce both the development of diabetes and progression of its complications.

Since it was proposed, the Robot Operating System (ROS) has fostered solutions for various problems in robotics in the form of ROS packages. One of these problems is Simultaneous Localization and Mapping (SLAM), a problem solved by computing the robot pose and a map of its environment of operation at the same time. The increasingly availability of robot kits ready to be programmed and also of RGB-D sensors often pose the question of which SLAM package should be used given the application requirements. When the SLAM subsystem must deliver estimates for robot navigation, as is the case of applications involving autonomous navigation, this question is even more relevant. This work introduces an experimental analysis of GMapping and RTAB-Map, two ROS compatible SLAM packages, regarding their SLAM accuracy, quality of produced maps and use of produced maps in navigation tasks. Our analysis aims ground robots equipped with RGB-D sensors for indoor environments and is supported by experiments conducted on datasets from simulation, benchmarks and from our own robot.

The preparation of transition metal salt ammine complexes having oxidizing anions is a great challenge due to the reaction between the ammonia and oxidizing anions during the synthesis of these materials. However, they have an important role in the development of new oxidants in organic chemistry and especially as precursors in the preparation of mixed metal oxides and alloys in controlled temperature thermal decomposition reactions. Therefore, the synthetic procedures to prepare the complexes of transition metal permanganate, pertechnetate, and perrhenate (VIIB group tetraoxometallates) salts with ammonia as ligand or co-ligand have been comprehensively reviewed. The available data about the structure and spectroscopic properties of these compounds, including the hydrogen bonds that act as redox reaction centers under their thermal decomposition are given and evaluated. Their thermal decomposition processes and products have been summarized. The available pieces of information about their role in organic oxidation reactions like the oxidation of benzyl alcohols, and regeneration of oxo-compounds from oximes and phenylhydrazones including the kinetics of these processes have also been collected.

This study investigates the emergence of ertapenem-resistant, meropenem-susceptible (ErMs) among non-carbapenemase producing (NCP) and carbapenemase producing (CP) Escherichia coli and Klebsiella pneumoniae. As mutations for ertapenem resistance establish the genetic background for non-carbapenemase meropenem resistance, there is a great need for antibiotic stewards and researchers to understand the determinants of a strain’s propensity to become resistant. Whole genome sequencing was conducted on clinical carbapenem-resistant E. coli (CREC) and K. pneumoniae (CRKP) across 5 hospitals in San Antonio, U.S. from 2012-2018. The majority of carbapenem resistant Enterobacterales (CRE) were NCP (54%; 41/76). The blaCTX-M was found to be most prevalent among NCP isolates (p = 0.02). LC-MS/MS analysis of carbapenem hydrolysis revealed that blaCTX-M-mediated carbapenem hydrolysis, indicating the need to reappraise the term, “non-carbapenemase (NCP)” for quantitatively uncharacterized CRE strains harboring blaCTX-M. Antimicrobial susceptibility results showed that 56% of all NCPE isolates had an ErMs phenotype (NCPE vs. CPE, p < 0.001), with E. coli driving the phenotype (E. coli vs. K. pneumoniae, p < 0.001). ErMs strains carrying blaCTX-M, had approximately 4-fold more copies of blaCTX-M than ceftriaxone-resistant but ertapenem and meropenem susceptible (EsMs) isolates (3.7 v. 0.9, p < 0.001). ErMs also carried more mobile genetic elements (MGEs), particularly IS26 composite transposons, than EsMs (37 vs. 0.2, p < 0.0001). Immunoblot analysis demonstrated the absence of OmpC expression in NCP-ErMs E. coli, with 92% of strains lacking full contig coverage of ompC. Overall, this work provides evidence of a collaborative effort between blaCTX-M and OmpC in NCP strains that confer resistance to ertapenem but not meropenem. To thwart potential mismanagement of CRE infected patients, future efforts should focus on understanding the mechanism(s) underlying OmpC loss, developing rapid methods to detect blaCTX-M copy number variants, and targeted antimicrobials for NCPE and ErMs strains.

The present study aimed to evaluate the psychometric properties of the Greek version of the Jefferson Scale of Empathy—Student version (JSE-S) and its association with potential predictors among Greek-speaking undergraduate medical students. This study adopted a cross-sectional, comparative–descriptive research design. The study was conducted during October and November 2023. Cronbach’s α for the JSE-S was 0.846. Cronbach’s α values for the factors “perspective taking”, “compassionate care”, and “standing in the patient’s shoes” were 0.800, 0.715, and 0.748, respectively. The intraclass correlation coefficient for the JSE-S score in the test–retest study was 0.827 (95% CI = 0.647 to 0.915, p-value < 0.001), indicating a high level of reliability. The participants showed moderate empathy levels. Females scored higher than males on the Greek version of the JSE-S (108.8 vs. 102.8, p-value < 0.001). Moreover, students enrolled in the fourth academic year showed higher empathy mean scores than those enrolled in the first year (108.6 vs. 103.6, p-value = 0.012). Statistically significant empathy differences by specialty preferences or faith in God/supreme power were not found. The present study provided satisfactory evidence that the Greek JSE-S is a psychometrically sound measurement instrument. Empathy differences by gender were found in line with prior literature.

From a differential geometric perspective, information geometry (IG) aims to characterise the structure of statistical geodesic models. The research done for this paper offers a novel method for modelling the information geometry of a queuing system. From the perspective of IG, the manifold of the transient M/M/infinity queue is described in this context. The Fisher Information matrix (FIM) as well as the inverse of (FIM), (IFIM) of transient M/M/infinity QM are devised. In addition to that, new results that uncovered the significant impact of stability of QM on the existence of (IFIM) are obtained. Moreover, the Geodesic equations of motion of the coordinates of the underlying transient are obtained. Also, it is revealed that stable QM is developable (i.e., has a zero Gaussian curvature) and has a non-zero Ricci Curvature Tensor (RCT). Novel stability dynamics of transient M/M/iInfinity queue manifold is revealed by discovering the mutual dual impact between the behaviour of (RCT) and the stability(instability) phases of M/M/Infinity QM. Furthermore, a new discovery that presents the significant impact of stability of queue manifold and the continuity of the unique representation between M/G/1 queue manifold and Ricci Curvature Tensor (RCT). The information matrix exponential (IME) is devised. Also, it is shown that stability of the devised (IME) enforces the instability of M/M/ Infinity QM. More interestingly, novel relativistic info-geometric queueing theoretic links are revealed .

In recent years, there has been a growing interest in the preoperative modeling of fluid-structure interaction in the treatment of cerebral aneurysms. In this study, we investigate two cases involving laminar incompressible fluid flow interacting with hyperelastic materials (a vertical flap and aneurysm walls) under the effect of fluid flow. We present a finite element method (FEM) for these prototypical two-dimensional ($2D$) configurations, taking into account the complex flows and deformation of the variant's structure models. We use an Arbitrary Lagrangian-Eulerian (ALE) formulation in a continuum, fully monolithic coupled way, and discretize the fluid and solid domains using the quadratic LBB stable $P_2P_1$ finite element pair to approximate the displacement, velocity, and pressure spaces independently. The resulting discretized form of the nonlinear algebraic system is linearized using a variant of Newton's procedure, and the Jacobian matrices are approximated via the divided difference method. The resulting linear systems are solved using a direct solver MUMPS. We evaluate hydrodynamic forces such as drag and lift coefficients for nonlinear elastic material models, including Saint-Venant Kirchoff, Neo-Hookean, and Mooney-Rivlin (2 parameters) separately. To gain more physical insight into the problem, we verify the computed results by comparing the velocity, viscosity, and pressure fields. Our aim is to qualitatively analyze the changes in the mechanics of the wall behavior of the elasticity of the flap vs. the complexity of deformation, interface, details for prototypical flow situations, corresponding displacement, and deformation. We also provide a physical interpretation of blood flow magnitude and basic hemodynamic phenomena of wall shear stresses (WSS) in aneurysma and the range of deformation. Overall, this study presents a comprehensive approach to modeling fluid-structure interaction in cerebral aneurysms, which could help in the development of more effective treatment strategies.

Rare-earth tetraborides RB4 are of great interest due to the occurrence of geometric magnetic frustration and corresponding unusual magnetic properties. While the Gd3+ spins in GdB4 align along the ab plane, Er3+ spins in the isomorphic ErB4 are confined to the c–axis. The magnetization in the latter exhibits a plateau at the midpoint of the saturation magnetization. Therefore, solid solutions of (Gd, Er)B4 provide an excellent playground for exploring the intricate magnetic behavior in these compounds. Single crystals of Gd(1-x)Erx B4 (x = 0, 0.2, and 0.4) were grown in aluminum flux. X-ray diffraction scans revealed single phase materials, and a drop in the unit cell volume with increasing Er content, suggesting the partial substitution of Er at the Gd sites. Heat capacity measurements indicated a systematic decrease of the Néel temperature (TN) with increasing Er content. The effective magnetic moment determined from the magnetization measurement agreed with the calculated free-ion values for Gd3+ and Er3+, providing further evidence for the successful substitution of Er for Gd. The partial substitution resulted in an anomalous ferromagnetic phase below TN, exhibiting significant anisotropy, predominantly along the c-axis. This intriguing behavior merits further studies of the magnetism in the Gd(1-x)ErxB4 borides.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

Study Objectives: To (1) investigate the prevalence of sleep disorder symptoms in caregivers of children with autism spectrum disorder (ASD) and (2) the relationships between caregiver sleep problems and their health-related quality of life and family quality of life. Methods: Descriptive cross-sectional study of caregivers (N=62) of children ages 6 to 11 years old diagnosed with ASD receiving care at a regional autism research and resource center. Measurements and Results: Participants completed the Sleep Habits Questionnaire (SHQ), the Medical Outcomes Study (MOS) SF-12, and the Beach Center Family Quality of Life Scale (FQOL). Caregivers with longer sleep duration reported better mental health and better family quality of life. Caregivers who reported insomnia symptoms, non-restorative sleep, and insufficient sleep were more likely to report poorer mental health than caregivers who did not report these sleep disorder symptoms. Caregivers with obstructive sleep apnea and restless legs syndrome experienced worse physical quality of life. Conclusions: The physical and mental health of the primary caregiver is essential to the support of the child with ASD and to the functioning of the family. The study findings point to the importance of future research and interventions to enhance sleep health in order to improve quality of life for caregivers of children with ASD.

A new set of basis functions is presented. The foundation in mathematics is established. To reconstruct a signal, it is compared to the Fourier basis functions. The M-basis functions' potential applications are also presented.

Increasing environmental distress is associated with a growing asthma incidence and, with no treatments available, montelukast (MTK) – an antagonist of the cysteinyl leukotrienes receptor 1 – is widely used in the management of symptoms among adults and children. Recently, new molecular targets have been identified and MTK has been proposed for repurposing in other therapeutic applications, with several ongoing clinical trials. The proposed applications include neuroinflammation control, which could be explored in some neurodegenerative disorders, such as Alzheimer’s and Parkinson’s diseases (AD and PD). However, this drug has been associated with an increasing number of reported neuropsychiatric adverse drug reactions. Besides, and despite being on the market since 1998, MTK metabolism is still poorly understood and the mechanisms underlying neuropsychiatric ADRs remain unknown. We review the role of MTK as modulator of leukotriene pathways and systematize the knowledge about MTK metabolism. Known toxic effects of MTK are discussed, and repurposing applications are presented comprehensively, with a focus on AD and PD.

Symbioses between animals and bacteria are ubiquitous. To better understand these relationships, it is essential to unravel how bacteria evolve to colonize hosts. Previously, we serially passaged the free-living bacterium, Shewanella oneidensis, through the digestive tracts of germ-free larval zebrafish (Danio rerio) to uncover the evolutionary changes involved in the initiation of a novel symbiosis with a vertebrate host. After 20 passages, we discovered an adaptive missense mutation in the mshL gene of the msh pilus operon, which improved host colonization, increased swimming motility, and reduced surface adhesion. In the present study, we have determined that this mutation was a loss-of-function mutation and found that it improved zebrafish colonization by augmenting S. oneidensis representation in the water column outside larvae through a reduced association with environmental surfaces. Additionally, we found that strains containing the mshL mutation were able to immigrate into host digestive tracts at higher rates per capita. However, mutant and evolved strains exhibited no evidence of a competitive advantage after colonizing hosts. Our results demonstrate that bacterial behaviors outside the host can play a dominant role in facilitating the onset of novel host associations.

The eugenol derivative, ethyl 4-(2-methoxy-4-(oxiran-2-ylmethyl)phenoxy)butanoate 1, with promising insecticidal capability was encapsulated in liposomal formulations of egg-phosphatidylcholine/cholesterol (Egg-PC:Ch) 70:30 and of 100% dioleoylphosphatidylglycerol (DOPG). Compound-loaded Egg-PC:Ch liposomes exhibit small hydrodynamic diameters (below 100 nm), high encapsulation efficiency (88.8% ± 2.7%), higher stability and a more efficient compound release, being chosen for assays in Sf9 insect cells. Compound 1 elicited a loss of cell viability up to 80% after 72h of incubation. Relevantly, encapsulation maintained the toxicity of compound 1 towards insect cells, while it lowered toxicity towards human cells, thus showing the selectivity of the system. Structure based inverted virtual screening was used to predict the most likely targets and molecular dynamics simulations and free energy calculations were used to demonstrate that this molecule can form a stable complex with insect odorant binding proteins and/or acetylcholinesterase.

Aging is a complex process associated with tissue degeneration and an increased risk of age-related diseases. This study aimed to evaluate the impact of Terasen®, a nutraceutical containing standardized extracts of Euterpe oleracea, Myrciaria dubia, and purified oil of Bixa orellana and Astrocaryum aculeatum on the lifespan of Caenorhabditis elegans, a widely used model organism for aging research. The findings demonstrated that Terasen® exhibited significant antioxidant activity and influenced the feeding behavior of C. elegans, leading to a reduced pharyngeal pumping rate and a decreased number of offspring produced by treated individuals. Notably, Terasen® also displayed a remarkable ability to extend the lifespan of C. elegans. These findings suggest that Terasen® may possess promising anti-aging effects in vivo, warranting further investigation.

Recently a measure termed F* was described, as an interpretable transformation of the F measure, also known as the Dice coefficient. Using elementary mathematical methods, it is shown that F* is in fact identical to a previously described measure, monotonically related to the F measure, and variously termed in previous publications, dating from the late 19^th to the late 20^th century, as the ratio of verification, the Jaccard similarity measure or index, the threat score, the Tanimoto index, and the critical success index. The origins of these different terms in different disciplines (weather forecasting, ecology, machine learning) may explain the repeated independent redescription of this measure.

We report on the occurrence of natural Magnesium Alumina Silicate Hydrate (M-(A)-S-H) cement at Feragen and Leka in eastern and western Trøndelag Norway, respectively. Both occurrences are located in the sub-arctic climate zone and form in glacial till and moraine material deposited on ultramafic rock during the Weichselian glaciation. Weathering of serpentinized peridotite dissolve brucite and result in a relative high pH alkaline fluid that subsequently reacts with the felsic minerals of the till (quartz, plagioclase, K-feldspar) to form a cement consisting of an amorphous material or a mixture of nanocrystalline Mg-rich phyllosilicates, including illite. The presence of plagioclase in the till results in the enrichment of alumina in the cement, i.e., forms M-A-S-H instead of the M-S-H cement. Dissolution of quartz results in numerous etch-pits and negative quartz crystals filled with M-A-S-H cement. Where the quartz dissolution is faster that the cement precipitation, a honeycomb-like texture is formed. Compositionally the cemented till (tillite) contains more MgO and has a higher loss of ignition than the till, suggesting that the cement is formed by a MgO fluid that previously reacted with the peridotite. The M-(A)-S-H cemented till represent a new type of duricrust, coined magsilcrete. The study of natural Mg-cement provides information on peridotites as a Mg-source for Mg-cement and as a feedstock for CO2 sequestration.

In a changing climate, extreme weather events such as heat waves will be more frequent and could affect grain weight and the quality of crops such as wheat, one of the most significant crops in terms of global food security. In this work, we characterized the response of Triticum turgidum spp. durum wheat to a short-term heat-stress (HS) treatment at transcriptomic and physiological levels during early grain filling in glasshouse experiments. We found a significant reduction in grain weight and size from HS treatment. Grain quality was also affected, showing a decrease in starch content in addition to increments in grain protein levels. Moreover, an RNA-seq analysis of durum wheat grains allowed us to identify 1590 differentially expressed genes related to photosynthesis, response to heat, and carbohydrate metabolic process. A gene regulatory network analysis of HS-responsive genes uncovered novel transcription factors (TFs) controlling the expression of genes involved in abiotic stress response and grain quality, such as a member of the DOF family predicted to regulate glycogen and starch biosynthetic processes in response to HS in grains. In summary, our results provide new insights into the extensive transcriptome reprogramming that occurs during short-term HS in durum wheat grains.

The misuse of antibiotics during the last decades led to the emergence of multidrug resistant pathogenic bacteria. This phenomenon constitutes a major public health issue. Consequently, the discovery of new antibacterials in the short term is crucial. Colicins, due to their antibacterial properties, thus constitute good candidates. These toxin proteins, produced by E. coli to kill enteric relative competitors, exhibit cytotoxicity through ionophoric activity or essential macromolecule degradation. Among the 25-colicin types known to date, colicin M (ColM) is the only one colicin interfering with peptidoglycan biosynthesis. Accordingly, ColM develops its lethal activity in E. coli periplasm by hydrolyzing the last peptidoglycan precursor, lipid II, into two dead-end products, thereby leading to cell lysis. Since the discovery of its unusual mode of action, several ColM orthologs have also been identified based on sequence alignments; all of the characterized ColM-like proteins display the same enzymatic activity of lipid II degradation and narrow antibacterial spectra. This publication aims at being an exhaustive review about what is currently known on this new family of antibacterial enzymes as well as on their potential use of food preservatives or therapeutic agents.

Leaf springs are critical components for the railway vehicle safety in which they are installed. Although these components are produced in high-strength alloyed steel and designed to operate under cyclic loading conditions in the high-cyclic fatigue region, their failure is still possible to occur and hence lead to economic and human catastrophes. The aim of this document is precisely to characterise the mechanical crack growth behaviour of the 51CrV4 spring steel representative of leaf springs under cyclic conditions, that is, crack propagation in mode I. The common fatigue crack growth prediction models (Paris and Walker) considering the effect of stress ratio and parameters such as propagation threshold, critical stress intensity factor and crack closure ratio are also determined using statistical methods, which resulted in good approximations with respect to the experimental results. Lastly, the fracture surfaces under the different test conditions were analysed using SEM, with no significant differences to declare. As a result of this research work, it is expected that the developed properties and fatigue crack growth prediction models can assist design and maintenance engineers in understanding fatigue behaviour in the initiation and propagation phase of cracks in leaf springs for railway freight wagons.

A popular approach to learning about admixture from population genetic data is by computing the allele-sharing summary statistics known as f-statistics. Compared to some methods in population genetics, f-statistics are relatively simple, but interpreting them can still be complicated at times. In addition, f-statistics can be used to build admixture graphs (multi-population trees allowing for admixture events), which provide more explicit and thorough modeling capabilities but are correspondingly more complex to work with. Here, I discuss some of these issues to provide users of these tools with a basic guide for protocols and procedures. My focus is on the kinds of conclusions that can or cannot be drawn from the results of f₄-statistics and admixture graphs, illustrated with real-world examples involving human populations.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

In the context of Shared Autonomous Vehicles, the need to monitor the environment inside the car will be crucial. This article focuses on the application of deep learning algorithms to detect objects, namely lost/forgotten items to inform the passengers, and aggressive items to monitoring if violent actions may arise between passengers. For object detection algorithms was used public datasets (COCO and TAO) to train state-of-the-art algorithms, such as YOLOv5. For violent action detection was used the MoLa InCar dataset to train on state-of-the-art algorithms such as I3D, R(2+1)D, SlowFast, TSN and TSM. At the end an embedded automotive solution was used to demonstrate both methods running in real-time.

In this work, we develop a self-consistent physical model of bubbles in a gas solid two-phase flow. Using the Peng-Robonson state equation and a detailed specific heat ratio equation of bubbles, we obtain the kinetic equations of the bubbles on the basis of the Ergun equation, thermodynamic equations, and kinetic equations. It is found that the specific heat ratio of bubbles in such systems strongly depends on bubble pressures and temperatures, which play an important role in the characteristics of the bubbles. The theoretical studies show that with increasing height in the systems, the gas flow rate shows a downward trend. Moreover, the larger particles in the gas solid flows are, the greater the gas velocity is. The bubble sizes increase with the increasing heights of the gas solid systems, and then decrease. The bubble velocity is affected by the gas velocity and the bubble size, which gradually increase and eventually quasi-stabilize. This shows that gas and solid phases in a gas solid two-phase flow interact with each other and a self-consistent system comes into being. The theoretical results have exhibited important value as a guide for understanding the properties and effects of bubbles in gas solid two-phase flows.

Caregiver burden, a response to the challenges faced by those caring for sick loved ones, combines objective caregiving aspects with subjective experiences. This study aimed to describe the caregiver burden in guardians of ailing animals with dermatological and oncological pathologies. Additionally, the study aimed to correlate the degree of caregiver burden with the duration of the animal's treatment, disease stability, family income, owner's age, and the number of people living in the same household responsible for the animal's treatment. Using a cross-sectional approach, questionnaires were administered to guardians at a veterinary hospital. Out of 182 valid responses, 50.55% related to oncological patients and 49.45% to dermatological patients. Notably, 36.9% of oncological and 37.8% of dermatological guardians exhibited clinically significant burden, with no statistical differences between the groups. Of the respondents, 84.6% were dog guardians, with 34.4% showing a significant burden. Feline guardians (15.4% of respondents) exhibited a higher burden (53.5%) compared to dog guardians (p = 0.02). Disease stability, time since diagnosis, and guardian age significantly influenced the burden, while household composition, income, and treatment duration showed no substantial impact. These findings underscore the psychosocial impact of caring for animals, emphasizing the need for a comprehensive understanding of the caregiver's perspective.

The adoption of ADS-B in Latin America has been gradual but steady. Some countries, such as Brazil, Chile and Mexico, have made significant progress in the implementation of this system, while others are still in the early stages. It should be noted that the implementation of ADS-B is used in both military and civilian environments. For this reason, this research aims to provide information on the different characteristics that make up the surveillance systems. However, there are fundamental factors to promote the adaptation of ADS-B in Latin America, since they reduce the risk of collisions and air accidents by providing accurate and real-time information on the position and altitude of aircraft. On the other hand, it allows optimizing flight routes and reducing waiting time on the ground, which translates into fuel and cost savings for airlines. ADS-B increases the number of aircraft that can safely operate in the same airspace, which is especially important in regions with growing air traffic. ADS-B adoption in Latin America is expected to continue to grow in the coming years. The drivers for ADS-B adoption remain in place, and governments in the region are taking steps to accelerate its implementation.

In this work, we explore a the different forms of a new type of modified gravity, namely f(φ) gravity. We construct the Big Rip type for the energy density and the curvature of the universe. We show that dark energy is a result of the transformation of the field φ mass (dark matter) to energy. In addition, we provide that Ω_{m}≈0,050, Ω_{DM}≈0,2, Ω_{DE}≈0,746, is in excellent agreement with observation data. We explore a generalized formalism of braneworld modified gravity. We also construct a new field equations, which generalize the Einstein field equations. We provide a relation between the extra dimension in 3-brane with the vacuum energy density. We show that the energy density of matter depends directly on the number of dimensions. We manage to find the value of the Gauss-Bonnet coupling α=1/4 which is a good agreement with the results in the literature, this correspondence creates a passage between f(R) gravity and Gauss-Bonnet gravity, this comparison leads to a number of bulk dimensions equal to D=10¹²¹+4.

In many application problems, F-transform algorithms are very efficient. In F-transform techniques, we replace the original signal or image with a finite number of weighted averages. The use of weighted average can be naturally explained, e.g., by the fact that this is what we get anyway when we measure the signal. However, most successful applications of F-transform have an additional not-so-easy-to-explain feature: the partition requirement, that the sum of all the related weighting functions is a constant. In this paper, we show that this seemingly difficult-to-explain requirement can also be naturally explained in signal-measuring terms: namely, this requirement can be derived from the natural desire to have all the signal values at different moments of time estimated with the same accuracy.

In this paper we have defined the effect of bulk viscosity on Quintessence model and scaler field potential as well as on classical field. We have shown the same effect for modified gravity with f(R,T)= R+f(T). In the derivation we have predicted the possibility of time dependent evolution of gravitational constant G and anisotropy.

The compatibility between the de Sitter Swampland conjecture and Ho\v{r}ava-Lifshitz $F(\bar{R})$ theories with a flat FLRW metric is studied. We first study the standard $f(R)$ theories and show that the only way in which the dS conjecture can be made independent of $R$ is by considering a power law of the form $f(R)\sim R^{\gamma}$. The conjecture and the consistency of the theory puts restrictions on $\gamma$ to be greater but close to $1$. For the $F(\bar{R})$ theories described by its two parameters $\lambda$ and $\mu$ we use the equations of motion to construct the function starting with an ansatz for the scale factor in the Jordan frame of the power law form. By doing a conformal transformation on the three metric to the Einstein frame we can obtain an action of gravity plus a scalar filed by relating the parameters of the theory. The non-projectable and projectable cases are studied and the differences are outlined. The $F(\bar{R})$ function obtained consists of terms of the form $\bar{R}^{\gamma}$ with the possibility of having negative power terms. The dS conjecture leads to inequalities for the $\lambda$ parameter, in both versions it gets restricted to be greater but close to $1/3$. For the general case in which $\mu$ and $\lambda$ are considered as independent, the action contains an extra term but we propose that the conjecture is still applicable. Once again the non-projectable and projectable cases are studied. The $F$ function obtained has the same form as before, the consistency of the theory and the dS conjecture lead to a set of inequalities on both parameters that are studied numerically. In all cases $\lambda$ is restricted by $\mu$ around $1/3$ and we obtain $\lambda\to1/3$ if $\mu\to0$. Finally we consider the $f(R)$ limit $\mu,\lambda\to1$ and we obtain consistent results.

Fault detection in PV arrays and inverters is critical for ensuring maximum efficiency and performance. Artificial intelligence (AI) learning can be used to quickly identify issues, resulting in a sustainable environment with reduced downtime and maintenance costs. As the use of solar energy systems continues to grow, the need for reliable and efficient fault detection and diagnosis techniques becomes more critical. This paper presents a novel approach for fault detection in photovoltaic (PV) arrays and inverters, combining AI techniques. It integrates Elman Neural Network (ENN), Boosted Tree Algorithms (BTA), Multi-layer Perceptron (MLP), and Gaussian Processes Regression (GPR) for enhanced accuracy and reliability in fault diagnosis. It leverages their strengths for accuracy and reliability of fault diagnosis. Feature engineering-based sensitivity analysis was utilized for feature extraction, the fault detection and diagnosis were assessed using several statistical criteria including PBAIS, MAE, NSE, RMSE, and MAPE. Two intelligent learning scenarios are carried out, the first scenario is done for PV array fault detection with DC power (DCP) as output. The second scenario is done for inverter fault detection with AC power (ACP) as the output. The proposed technique is capable of detecting faults in PV arrays and inverters, providing a reliable solution for enhancing the performance and reliability of solar energy systems. Real-world solar energy dataset is used to evaluate the proposed technique, with results compared to existing detection techniques and obtained results show that it outperforms existing fault detection techniques, achieving higher accuracy and better performance. The GPR-M4 optimization justified reliably among all the models with MAPE=0.0393, and MAE=0.002 for inverter fault detection and MAPE=0.091, and MAE=0.000 for PV array fault detection.

A commercially reared domesticated turkey (Meleagris gallopavo) was purchased from a local market and sections of tissue representing leg, thigh, and breast were harvested and processed for analysis of the lipids and proteins present. Leg and thigh tissue was enriched in mitochondrial proteins whereas the breast tissue was enriched in glycolytic enzymes as well as the cytosolic and mitochondrial forms of glycerol-3-phosphate dehydrogenase. A potential marker for breast tissue muscle formation and/or function was also identified. The tissues could clearly be separated based upon their lipid profiles with little differences in cardiolipin levels suggesting that mitochondrial surface areas may be similar across the tissues. The most significant differences in the lipids were found to be higher levels of oxidized lipids in thigh meat. This work provides the first untargeted proteome and lipidome datasets for the domesticated turkey. The proteome dataset is accessible from ProteomeXchange Consortium via the PRIDE partner repository with the identifier PXD008207.

In the present study, we aimed to determine the antimicrobial resistance and genetic structure of a population of S. aureus recovered from transient and persistent intramammary infections and nares/muzzles. We investigated the antimicrobial resistance of 189 S. aureus strains using a broad antimicrobial susceptibility profile. Furthermore, 107 S. aureus isolates were strain-typed using staphylococcal protein-A (spa) typing. Here, a great proportion of strains exhibited multidrug resistance to antimicrobials, including resistance to critically important antimicrobials, although no methicillin-resistant S. aureus strains were found. Our study did not strengthen the idea that extramammary niches (i.e., nares/muzzles) are an important source for S. aureus. A discrepancy in the antimicrobial resistance between S. aureus strains isolated from nasal/muzzles and milk samples was observed. Furthermore, S. aureus isolates from transient and persistent IMIs did not differ by spa typing, suggesting that the persistence of bovine IMIs was determined by cow factors. Thus, the high level of multidrug-resistant S. aureus found in the two herds studied together with the predominance of a well udder-adapted S. aureus strain may contribute to the history of the high prevalence of mastitis caused by S. aureus, leading to great animal and public health concerns.

Defects in pre-mRNA splicing are frequently a cause of Mendelian disease. Despite the advent of next-generation sequencing, allowing a deeper insight into a patient’s variant landscape, the ability to characterize variants causing splicing defects has not progressed with the same speed. To address this, recent years have seen a sharp spike in the number of splice prediction tools leveraging machine learning approaches, leaving clinical geneticists with a plethora of choices for in silico analysis. In this Review, some basic principles of machine learning are introduced in the context of genomics and splicing analysis. A critical comparative approach is then used to describe seven recent machine learning-based splice prediction tools, revealing highly diverse approaches and common caveats. We find that, although great progress has been made in producing specific and sensitive tools, there is still much scope for personalized approaches to prediction of variant impact on splicing. Such approaches may increase diagnostic yields and underpin improvements to patient care.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

As abiotic stress, drought limits plant growth and minimizes productivity. The increased request for valuable essential oil extracted from geranium (Pelargonium graveolens L.) is mainly associated with plant growth, which is adversely affected by drought. Melatonin (MT) has been used to enhance plant growth under abiotic stress, however, its impact to overcome drought stress of aromatic plants including geranium is poorly investigated. In the current investigation, MT application at 100 µM was applied under 100 % (well-watered) or 50 % (drought stress) of FC to verify this role. Drought stress markedly reduced growth parameters, herb yield, and total chlorophyll; however, MT alleviated these effects. In contrast, drought enhanced the essential oil percentage in geranium leaves. Despite the reduction in oil yield caused by drought, MT application mitigated this reduction and improved both oil yield and oil components. Besides, MT treatment enhanced the accumulation of total phenols, glutathione, and proline and improved the activity of ascorbate peroxidase, catalase, and glutathione reductase with possible alleviation of drought-induced oxidative damage. Therefore, it reduced both H2O2 and malondialdehyde accumulation, and finally maintained membrane integrity. Overall, this is the first report that reveals that MT application can improve geranium resistance to drought by enhancing the antioxidant potential and protecting the cell membrane from oxidative damage.

The considerable biological and medicinal activities of pyridazines has stimulated considerable research on efficient syntheses of these derivatives. In the last decade, microwave irradiation has generally been used for the energy source. As demonstrated in recent studies, pressure reactor “Q-tubes” may be used to accelerate several of these reactions in a more optimal and safer manner (compared to microwaves). In these studies there has been postulated a pathway for the formation of pyridazino[5,4,3-de][1,6]naphthyridine derivatives . In this paper we consider this pathway, and an alternate pathway, for several reactions. Contrary to the suggestion in these studies the pathway in which initial dimerization of malononitrile was postulated could be excluded based on chemical evidence. The reactions performed were the reaction of arylhydrazonals 1a,b with benzylidinemalononitrile which afforded in Q-tube the 3-acyl-4-aryl-1-phenyl-6-amino-1,4-dihydropyridazines, and the reaction of arylhydrazonals 1a,b, malononitrile 9 and aromatic aldehydes 10a-g in Q-tubes which afforded the tricyclic systems 12a-n whose structure could be established by X-ray crystal structure determination. In conclusion, we have added to the work of the recent studies by excluding a reaction pathway for one of their reaction products.

This research elucidates the dynamic expression of expansin genes during the wheat grain (Triticum aestivum L.) development process using comprehensive meta-analysis and experimental validation. We leveraged RNA-seq data from multiple public databases, applying stringent criteria for selection, and identified 60,852 differentially expressed genes across developmental stages. From this pool, 28,558 DEGs were found to exhibit significant temporal regulation in at least two different datasets, and were enriched for processes integral to grain development such as carbohydrate metabolism and cell wall organization. Notably, 30% of the 241 known expansin genes showed differential expression during grain growth. Hierarchical clustering and expression level analysis revealed temporal regulation and distinct contributions of expansin subfamilies during the early stages of grain development. Further analysis using co-expression networks underscored the significance of expansin genes, revealing their substantial co-expression with genes involved in cell wall modification. Finally, qPCR validation and grain morphological analysis under field conditions indicated a significant negative correlation between expression of select expansin genes and grain size and weight. This study illuminates the potential role of expansin genes in wheat grain development and provides new avenues for targeted genetic improvements in wheat.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

Concentrator photovoltaic (CPV) technology offers an alternative to conventional photovoltaic systems, focusing on the concentration of solar radiation through the optics of the system onto smaller and more efficient solar cells. However, the surface on which the solar beam is incident must remain oriented towards the position of the sun, which requires the use of large and heavy external elements known as solar trackers. In addition to their size, these elements must be as accurate as possible to avoid misalignment. To avoid the need of these solar trackers, the concept of tracking-integrated concentrating systems has been developed. This technology has been researched to make CPV systems accessible in places where conventional systems are not viable, such as building roofs or agrivoltaic fields. This review presents a detailed classification of the existing designs in the literature and providing an overview of this type of system. By eliminating the need for external solar trackers, tracking-integrated CPV systems offer a promising solution to increase the adoption of this technology. Therefore, it is expected that these systems will be a viable and effective option for solar power generation.

Extensive genome structure variation, such as copy number variations (CNVs) and presence/absence variations, is the basis for the remarkable maize genetic diversity; however, the effect of CNVs on maize herbivory defense remains largely underexplored. Here, we report that the naturally occurring duplication of the maize 9-lipoxygenase gene, ZmLOX5, leads to increased resistance of maize to herbivory by fall armyworms (FAW). Previously, we showed that ZmLOX5-derived oxylipins are required for defense against chewing insect herbivores and identified several inbred lines, including Yu796, that contained duplicated CNVs of ZmLOX5, referred to as Yu796-2×LOX5. To test whether introgression of the Yu796-2×LOX5 locus into the herbivore-susceptible B73 background that contains a single ZmLOX5 gene is a feasible approach to increase resistance, we generated a series of near-isogenic lines that contained either 2, 1 or 0 copies of the Yu796-2×LOX5 locus in the B73 background by six back crosses (BC6). Droplet digital PCR (ddPCR) confirmed the successful introgression of the Yu796-2×LOX5 locus in B73. The resulting B73-2×LOX5 inbred line displayed increased resistance against FAW associated with increased expression of ZmLOX5, increased wound-induced production of its primary oxylipin product, the α-ketol, 9-hydroxy-10-oxo-12(Z),15(Z)-octadecadienoic acid (9,10-KODA), and the downstream defense hormones regulated by this molecule, 12-oxo-phytodienoic acid (12-OPDA) and abscisic acid (ABA). Surprisingly, wound-induced JA-Ile production was not increased in B73-2×LOX5, resulting from the increased JA catabolism. Furthermore, B73-2×LOX5 displayed enhanced drought tolerance likely due to increased ABA and 12-OPDA content. Taken together, this study revealed that the duplicated CNV of ZmLOX5 quantitively contributes to maize antiherbivore defense and presents proof-of-concept evidence that the introgression of naturally occurring duplicated CNVs of a defensive gene into the productive, but susceptible, crop varieties is a feasible breeding approach for enhancing plant resistance to herbivory and tolerance to abiotic stress.

The World Health Organization(WHO) in 2016 considered mHealth as: “the use of mobile wireless technologies including smart devices such as smartphones and smartwatches for public health” as an important resource for health services delivery and public health given their ease of use, broad reach and acceptance. WHO emphasizes the potential of this technology to increase access to health information, services and skills as well as promoting positive changes in health behaviors and management of diseases. In this regard, the capability of smartphones and smartwatches for m-health monitoring as well as verification of the patient the signal has become an important component of mHealth system. Most of the smartwatches could extract more than one bioelectrical signal therefore, therefore they provide suitable platform for extracting health data for e-monitoring. The existing approaches have not considered the integrity of data obtained from these smart devices. Therefore, it is important that the integrity of the collected data be verified continuously through user authentication. This could be done using any of the bioelectrical signals extracted and transmitted for e-monitoring. In this article, a smartwatch is used for extracting bioelectrical signal before decomposing the signal into sub-bands of Detail and Approximation Coefficient for user authentication. To select suitable features using biorthogonal wavelet decomposition of signal from a non-intrusive extraction, a detailed experiment is conducted extracting suitable statistical features from the bioelectrical signal from 30 subjects using different biorthogonal wavelet family. Ten features are extracted using Biorthogonal wavelet to decompose the signal into three levels of sub-band Detail and Approximation Coefficient and features extracted from each level the decomposed Detail and Approximation Coefficients. Comparison analysis is done after the classification of the extracted features based on the Equal Error Rate (EER). Using Neural Network (NN) classifier, Biorthogonal Wavelet Detail Coefficient Sub-band level 3 of bior1.1 achieved the best result of EER 13.80% with the fusion of the best sub-band three levels of bior1.1 achieving a better result of 12.42% EER.

Let R be a commutative ring with identity and m, n be positive integers. In this paper, we introduce the class of (m,n)-prime ideals which lies properly between the classes of prime and (m,n)-closed ideals. A proper ideal I of R is called (m,n)-prime if for a,b∈R, a^{m}b∈I implies either aⁿ∈I or b∈I. Several characterizations of this new class with many examples are given. Analougus to primary decomposition, we define the (m,n)-decomposition of ideals and show that every ideal in an n-Noetherian ring has an (m,n)-decomposition. Furthermore, the (m,n)-prime avoidance theorem is proved.

We report on metastable defects introduced in n-type 4H-SiC material by epithermal and fast neutron irradiation. The epithermal and fast neutron irradiation defects in 4H-SiC are much less explored compared to electron or proton irradiation induced defects. In addition to silicon vacancy (Vsi) and carbon antisite-carbon vacancy (CAV) complex, the neutron irradiation has introduced four deep level defects, all arising from the metastable defect, the M-center. The metastable deep level defects were investigated by deep level transient spectroscopy (DLTS), high-resolution Laplace DLTS (L-DLTS) and isothermal DLTS. The existence of the fourth deep level M4, recently observed in ion implanted 4H-SiC, has been additionally confirmed in neutron irradiated samples. The isothermal DLTS technique has been proven as a useful tool for studying the metastable defects.

CD4+ T cells orchestrate and regulate immunity within jawed vertebrates, yet our understanding of their evolution, development, and cellular physiology has only begun to be unearthed in the past few decades. Discoveries of genetic diseases that ablate this cellular population have provided insight into their critical functions while transcriptomics, proteomics, and highresolution microscopy have recently revealed new insights into CD4+ T cell anatomy and physiology. This article compiles historical, microscopic, and multi omics data which can be used as a reference atlas to dissect cellular physiology within these influential cells and further understand pathologies like HIV infection that inflict human CD4+ T cells.

The current work reports the upper bound of the state variable of the of the Pointwise Steady Fluid Flow Approximation (PSFFA) model of non-stationary M/Ek/1 queueing system.

Anion doping of tungsten trioxide by nitrogen is used to obtain electrochrome cathode material, the spectral transmittance of which can be controlled by the doping level. A series of samples was synthesized by reactive magnetron sputtering of a metal tungsten target in a mixture of argon, nitrogen and oxygen gases. Warm-colored tungsten oxynitride films were prepared at higher doping levels and characterized using scanning electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy techniques. Optical properties were measured making use of transmission spectrophotometry and spectroscopic ellipsometry. These extensive experimental studies revealed an increase in absorption towards shorter wavelengths with increasing the doping level. At the same time, it was found that with increasing the doping level, the fraction of non-stoichiometric oxygen also steadily increases to half the total oxygen content. The imperfection of the doped material can stimulate its intercalation with electrolyte ions, accelerating the coloring/bleaching process and increasing the dynamical range between the dark and clear states, thus improving the consumer qualities of electrochemical materials and devices.

The research presents the inter-comparison of atmospheric variables measured by 9 automatic meteorological stations. This set of data was compared with the measurements of other meteorological stations in order to standardize the values that must be adjusted when taken to different areas. The data of a set of a total of 9 GMX500, which measures conventional meteorological variables, and 10 WS100 sensors, which measures precipitation parameters. The automatic stations were set up at the Huancayo Observatory (Geophysical Institute of Peru) for a period of 5 months. The data set of GMX500 were evaluated comparing with the average of the 9 sensors and the WS100 was compared with a optical disdrometer Parsivel2. The temperature, pressure, relative humidity, wind speed, rainfall rate, and drop size distribution was evaluated. A pair of GMX500 sensors presented high data dispersion, it was found found that the errors came from a bad configuration; once this problem was solved, good agreement was archived, with low RMSE and high correlation. I was found that the WS100 sensors overestimate the precipitation with a percent bias close to 100% and the differences increase with the greater intensity of rain. The DSD retrieved by WS100 have unrealistic behavior with higher concentrations in diameters of 1 mm and 5 mm, in addition to a flattened curve.

The evolution of metals micro/nano-structure upon severe plastic deformation (SPD) is still far to be theoretically explained, while experimental datasets are persistently growing for several decades. Major problem associated with understanding of SPD is related to a fact that the latter is a synergetic product of several competing physical effects which alter the material micro/nano-structure. In attempt to find deformational boundaries, where predominantly one mechanism determines the micro/nano-structure, in this paper we propose a continuous piecewise model for the analysis of experiments on material hardness vs strain of SPD processed materials. The novelty of this approach lies in its ability to find, as free-fitting parameters, the strain breakpoints which separate different micro/nano-structure modes generated upon SPD process. The model is applied to analyse experimental data for polycrystalline samples of pure iron and two distinctive strain breakpoints are revealed with good accuracies. This finding is in a good agreement with our earlier results on TEM microscopy studies on pure iron polycrystals after SPD treatment.

In this work we present a novel steganography algorithm, based on Fractal Transform domain, combined with the principles of Cryptography. The proposed method uses a private key, which will indicate which segment of the image will be taken and encoded with the Fractal Transform, to then insert the secret bits in the transformed coefficients, thus generating the stego image.

Purpose: The study aimed to investigate if there were any links between liver function biomarkers and immunoglobulins levels in serum, and Toll-like receptors (TLRs) and neuropilin-1 (NRP1) in COVID-19 patients. The study also aimed to assess the accuracy—sensitivity, specificity, and area under the curve (AUC) by the receiver operator curve (ROC) analysis for immunoglobulins levels and TLRs expressions. Patients and Methods: This study included 150 patients (100 patients with confirmed COVID-19 and 50 healthy volunteers as a control group). Patients with COVID-19 were subdivided into two groups according to the severity of symptoms (moderate and severe, with 50 patients each). Serum C-reactive protein (CRP), alanine aminotransaminase (ALT), aspartate aminotransaminase (AST), albumin, lactate dehydrogenase (LDH), immunoglobulin (Ig) G, and IgM levels were estimated. TLRs (TLR2 and TLR4) and NRP1 gene expression in blood samples were investigated using quantitative real-time polymerase chain reaction (qRT-PCR). ROC analysis was also applied to determine the accuracy of various detected parameters in predicting the possibility of COVID-19 infection. Results: In COVID-19 patients, serum parameters related to liver function, except serum albumin, CRP, IgG, IgM, and TLR2, TLR4, and NRP1 mRNA expression levels, significantly elevated compared to controls. Severe COVID-19 patients exhibited significantly higher liver enzymes (ALT, AST and LDH), CRP, and TLR2 mRNA expression levels and lower albumin levels than the moderate group. In the moderate and severe groups, ALT, CRP, TLR2, and TLR4 had a significant positive correlation with IgM levels. ALT, AST, LDH, CRP, TLR2, and TLR4 showed a significant positive correlation with IgG levels in both groups. In both the moderate and severe groups, NRP1 expression was found to be significantly correlated with CRP, IgG, IgM, TLR2, and TLR4. In contrast, serum albumin levels exhibited a significant negative correlation with IgG and IgM levels only in the severe group, but they showed a significant negative correlation with TLR2, TLR4, and NRP1 expression in both moderate and severe groups. Serum ALT and AST activities were positively correlated with NRP1 expression in the moderate group but not in the severe group and as well as TLR2 and TLR4 expression in both the moderate and severe groups. ROC analysis indicated that AUC was higher than 0.800 for serum IgM level and TLR4 gene expression in moderate COVID-19 group. Conclusions: The increased liver function biomarkers in serum and NRP1 expression are closely correlated with sustained activations in humoral and innate immune responses during COVID-19 infection. As a result, TLR2, TLR4, and NRP1 could be targets for limiting COVID-19 infection and impairment effects on liver function. Moreover, detection of IgM level in serum and TLR4 expression in blood have a good accuracy in predicting the possibility of infection with COVID-19 in moderate cases.

Thin films (100-400 nm) of Ba_xSr_1-xTiO₃ (0≤x≤1) deposited in RF-magnetron co-sputtering equipment are presented in this research work. The change of deposition rate, gap energy, and resistivity as a function of temperature- applied power change in the growth parameters was studied through the ISO colour-code lines constructed with MATLAB: By analysing the trend information and take into account the influence of the calculated "x" parameter with the Boltzmann profile fitting is proposed a method to allow a controlled set up of the RF-magnetron co-sputtering system and predict the E_g and resistivity values in the Ba_xSr_1-xTiO₃ solid solution with 0≤x≤1 for amorphous and crystalline phases. Also, a versatile tool to optimise the deposition process and material properties.

Biocomposite membranes based on polylactic acid (PLA) and cellulose nanocrystals (CNCs) were developed using a scientific approach. Dicumyl peroxide (DCP) was used as a polymerization ini-tiator, while tin octoate (Sn(Oct)2) and triphenylphosphane (P(C6H5)3) were used as catalysts. A torque rheometer was used to mix the components of the biocomposite, and thin films was prepared by solvent casting. Fourier transform infrared (FTIR) spectroscopy confirmed the coupling between the PLA and CNCs. Field emission scanning electron microscopy (FESEM) showed that the CNCs were well-dispersed in the PLA matrix with an unimodal particle size distribution and a maximum particle size of around 200 nm. Thermogravimetric analysis (TGA) and differential scanning calo-rimetry (DSC) analysis demonstrated good thermal stability and improved biodegradability of the biocomposite membrane compared to pure PLA. Mechanical characterization showed a Young's modulus of 1.65 GPa, which is comparable to that of other composite materials, and a maximum tensile strength of 20.31 MPa, which is higher than that of pure PLA. These results suggest that the developed biocomposite membrane has potential applications in water filtration, food packaging, and biomedical devices.

Biofilm formation is important in the free-living and symbiotic lifestyles of Sinorhizobium meliloti. Here we show that the S. meliloti NspS-MbaA system is homologous to the c-di-GMP modulating NspS-MbaA system described in Vibrio cholerae and modulates biofilm formation, exopolysaccharide (EPS) production and motility in S. meliloti in response to exogenous polyamines. Biofilm and EPS production in quorum sensing-deficient wild type strain 1021 decreased in cultures containing putrescine, 1,3-diaminopropane or spermine, but were unaffected in a 1021 nspS mutant (1021 nspS). Decreases in biofilm formation caused by these polyamines paralleled decreases in EPS production and increases in nspS transcription. Cell aggregation did not differ markedly between strain 1021 and 1021 nspS. The S. meliloti quorum sensing-proficient Rm8530 wild type strain and nspS mutant (Rm8530 nspS) produced similar levels of biofilm under control conditions and 3.2- and 2.2-fold more biofilm in cultures with norspermidine, but these changes did not correlate with EPS production. Rm8530 nspS aggregated up to several fold more than the wild type under most conditions. Changes caused by polyamines in swimming and swarming motility were not generally dependent on NspS-MbaA in either 1021 or Rm8530. We speculate that the S. meliloti NspS-MbaA system could modulate biofilm formation in response to environmental polyamines.

Abstract: (1) Background: After the COVID-19 pandemic, there is increasing concern regarding the immunity of population to SARS-CoV-2 variants, particularly the Omi-cron variant and its sub-lineages. (2) Methods: The study involved analyzing the im-mune response and symptomatology of 27 vaccinated individuals who were subse-quently infected by Omicron sub-lineages. Blood samples were collected for serological analysis, including the detection of IgG antibodies reactive to the Nucleocapsid (N) and Spike (S) antigens of SARS-CoV-2. Additionally, participants were interviewed to assess the intensity of symptoms during the infection. (3) Results: Despite the high levels of anti-Spike IgG observed after vaccination, all participants were infected by Omicron sub-lineages. The most common symptoms reported by participants were fever or chills, sore throat, and cough. Surprisingly, the levels of anti-Spike IgG found prior to infection did not correlate with symptom severity post-infection. However, it was observed that high post-infection anti-Nucleocapsid IgG levels correlates with mild symptoms during the course of the disease, suggesting a potential role for anti-N antibodies in disease resolution. (4) Conclusions: The high levels of IgG anti-Spike resulting from vaccination may not provide complete protection against infection by the Omicron variant. Addi-tionally, our data suggest that anti-Nucleocapsid IgG titers are negatively correlated with the intensity of the symptoms during mild infections. These findings underscore the importance of ongoing surveillance of viral variants and continuous adaptation of vaccination strategies to ensure efficacy against SARS-CoV-2 variants.

This work addresses the role of charge regulation (CR) and the associated fluctuations in the conformational and mechanical properties of weak polyelectrolytes. Due to CR, changes in the pH-value modifies the average macromolecular charge and conformational equilibria. A second effect is that, for a given average charge per site, fluctuations can alter the intensity of the interactions by means of correlation between binding sites. We investigate both effects by means of Monte Carlo simulations at constant pH-value, so that the charge is a fluctuating quantity. Once the average charge per site is available, we turn off the fluctuations by assigning the same average charge to every site. A constant charge MC simulation is then performed. We make use of a model which accounts for the main fundamental aspects of a linear flexible polyelectrolyte i.e. proton binding, angle internal rotation, bond stretching and bending. Steric excluded volume and differentiated treatment for short-range and long-range interactions are also included in the model. It can be regarded as a kind of "minimal'' model in the sense that contains a minimum number of parameters but still preserving the atomistic detail. It is shown that, if fluctuations are activated, gauche state bond probabilities increase, and the persistence length decreases, so that the polymer becomes more folded. Macromolecular stretching is also analyzed in presence of CR (the charge depends on the applied force) and without CR (the charge is fixed to the value at zero force). The analysis of the low force scaling behavior concludes that Pincus exponent becomes pH-dependent. Both with and without CR, a transition from 1/2 at high pH-values (phantom chain) to 3/5 to low pH-values (Pincus regime), is observed. Finally, the intermediate force stretching regime is investigated. It is found that CR induces a moderate influence in the force-extension curves and persistence length (which in this force regime becomes force-dependent). It is thus concluded that the effect of CR on the stretching curves is mainly due to changes in the average charge at zero force. It is also found that, for the cases studied, the effect of steric excluded volume is almost irrelevant compared to electrostatic interactions.

In this work, nine fruits cultivated in the northern Amazon were studied: abiu, acerola, araçá, bacupari, biribá, caçarí, fruta-do-conde, graviola and taperebá, with the objective of carrying out a bromatological and nutritional study of the pulps of fruits studied. Of all of them, are the pulps of graviola (76.83 ± 0.02 kcal 100 g^-1) bacupari (76.83 ± 0.02 kcal 100 g^-1) and fruta-do-conde (46.66 ± 0.02 kcal 100 g^-1). Among the macronutrients, the high concentration of potassium stands out, especially in the graviola (541.16 ± 0.24 mg 100 g^-1) and the biribá (468.21 ± 0.13 mg 100 g^-1). Among the micronutrients, iron concentrations are representative for araçá pulp (3.04 ± 0.02 mg 100g-1), abiu is rich in zinc (3.71 ± 0.02 mg 100 g^-1) and manganese (6.61 ± 0.11 mg 100 g^-1). The presence of cobalt at the level of traces in some of the pulps studied stands out. The Pearson correlation coefficient was evaluated, as well as the statistical treatment by multivariate analysis PCA to establish the correlation between the variables studied.

Soil-borne Trichoderma spp. have been extensively studied for their biocontrol activities against pathogens and growth promotion ability with plants. However, the beneficial effect of Trichoderma on inducing resistance against insect herbivores has been considered only recently. Among diverse Trichoderma species, consistent with previous reports, we showed that root colonization by T. virens triggered induced systemic resistance (ISR) to leaf-infecting fungal pathogens. Whether T. virens induces ISR to insect pests has not been tested before. In this study, we investigated whether T. virens affects jasmonic acid (JA) biosynthesis and defense against fall armyworm (FAW) and western corn rootworm (WCR). Unexpectedly, the results showed that T. virens colonization of maize seedlings grown in autoclaved soil suppressed wound-induced production of JA, resulting in reduced resistance to FAW. Similarly, the bacterial endophyte Pseudomonas chlororaphis 30-84 suppressed systemic resistance to FAW due to reduced JA. Further comparative analyses of the systemic effects of these endophytes when applied into sterile or non-sterile field soil showed that both T. virens and P. chlororaphis 30-84 triggered ISR against hemibiotrophic fungal pathogen Colletotrichum graminicola in both soil conditions, but only suppressed resistance to FAW in sterile soil. In contrast to the effect on FAW defense, T. virens colonization of maize roots suppressed WCR larvae survival and weight gain. This is the first report suggesting the potential role of T. virens as a biocontrol agent against WCR.

This study explores the effect of seasonality on soil carbon efflux and pasture growth based on field and lysimeter experiments during summer-fall and winter-spring in two years. Focus is also pointed on irrigation strategies to alleviate the crop response to seasonal fluctuations in precipitation and surface temperatures. Soil respiration, soil and air temperature, leaf photosynthesis, plant dry weight and leaf area index were quantified and analyzed. It has been found significant differences in the CO₂ efflux between the two growing season. Emission of soil CO₂ allowed to characterize and to prioritize the temperature and rain influence in seasonal brachiaria response. During the seasons, the transient variation of CO₂ efflux was highly correlated with rainfall (r = 0.87, P < 0.05), and poorly correlated with soil temperatures (r = 0.5, P < 0.05). The CO₂ efflux and plant response to different level of reposition of evapotranspiration demonstrated that irrigation during fall mitigates the reduction of growth conditioned by drying soil and the lower temperatures. The lower temperatures are limiting only when the soil moisture is below 32% of the field capacity. Thus, we propose to keep the soil moisture around 50% during the fall as a key practices for mitigating the effect of seasonality and its intensification with the climate change, even more if added to management routine practices the soil and water conservation.

Older adults with diabetes are at elevated risk of complications following hospitalization. Home health care services mitigate the risk of adverse events and facilitate a safe transition home. In the United States, when home health care services are prescribed, federal guidelines require they begin within two days of hospital discharge. This study examined the association between timing of home health care initiation and 30-day rehospitalization outcomes in a cohort of 786,734 Medicare beneficiaries following a diabetes-related index hospitalization. Of these patients, 26.6% were discharged to home health care. To evaluate the association between timing of home health care initiation and 30-day rehospitalizations, multivariate logistic regression models including patient demographics, clinical, geographic variables, and neighborhood socio-economic variables were used. Inverse probability-weighted propensity scores were incorporated into the analysis to account for potential confounding between the timing of home health care initiation and the outcome in the cohort. Compared to patients who received home health care within the recommended first two days, patients who received delayed services (3-7 days after discharge) had higher odds of rehospitalization (OR 1.28, 95% CI 1.25-1.32). Among patients who received late services (8-14 days after discharge), the odds of rehospitalization were four times greater than for patients receiving services within 2 days (OR 4.12, 95% CI 3.97-4.28). Timely initiation of home health care following diabetes-related hospitalizations is one strategy to improve outcomes.

Pulmonary infections with Mycobacterium avium occur in susceptible individuals following exposure to the bacterium in the environment, where it often persists in biofilms. Many methods have been used to generate biofilms of M. avium, and it is unknown whether different approaches generate similar structures and cell phenotypes. To make a parallel comparison of in vitro biofilm ultrastructure, extracellular matrix (ECM) composition, and drug susceptibility of biofilm resident bacteria, we used two published methods to generate M. avium biofilms: four week incubation in M63 medium or 24 hour exposure to dithiothreitol (DTT). Scanning electron microscopy revealed differences in biofilm ultrastructure between the two methods, including variation in appearance of ECM materials and morphology of resident cells, while light microscopy and staining with calcofluor white indicated that both biofilms contained polysaccharides characteristic of cellulose. Measuring susceptibility of biofilms to degradation by enzymes suggested differences in structurally important ECM molecules, with DTT biofilms having important protein and, to a lesser extent, cellulose components, and M63 biofilms having moderate protein, cellulose, and DNA components. Both biofilms conferred resistance to the bactericidal effects of amikacin and clarithromycin, with resident cells being killed at &gt;10-fold lower rates than planktonic cells at almost all concentrations. Though these comparisons indicate differences in biofilm responses by M. avium under differing conditions, they also suggest common features of biofilm formation including cellulose production and antimicrobial resistance.

The topological index is a numerical quantity based on the characteristics of various invariants or molecular graph. For ease of discussion, these indices are classified according to their logical derivation from topological invariants rather than their temporal development. Degree based topological indices depends upon the degree of vertices. This paper computes degree based topological indices of Bismuth Tri-Iodide chains and sheets with the help of M-polynomial.

We improved a magnetic scanning microscope for measuring the magnetic properties of minerals in thin sections of geological samples at submillimeter scales. The microscope is comprised of a 200 µm diameter Hall sensor that is 142 µm from the sample; an electromagnet capable of applying to the sample up to 500 mT dc magnetic fields over a 40 mm diameter region; a second Hall sensor arranged in a gradiometric configuration to cancel the background signal applied by the electromagnet and reduce overall noise in the system; a custom-designed electronics to bias the sensors and provide adjustment for background signal cancelation; and a scanning XY stage with micrometer resolution. Our system achieves a spatial resolution of 220 µm with noise at 6.0 Hz of »300 nT_rms/(Hz)^1/2 in an unshielded environment. The magnetic moment sensitivity is 1.3 × 10⁻¹¹ Am².^1/2 We successfully measured the representative magnetization of a geological sample using an alternative model that takes into account the sample geometry and identified different micrometric characteristics in the sample slice.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

French Guiana, located in the Guiana Shield, is a natural reservoir for many zoonotic pathogens that are of considerable medical or veterinary importance. Until now, there are few data available on the description of parasites circulating in this area, especially on protozoan belonging to the phy-lum Apicomplexa; conversely, the neighbouring countries describe a high parasitic prevalence in animals and humans. Epidemiological surveillance is necessary, as new potentially virulent strains may emerge from these forest ecosystems, such as Amazonian toxoplasmosis. However, there is no standard tool for detecting protozoa in wildlife. In this study, we developed Meat-Borne-Parasite, a high-throughput meta-barcoding workflow for detecting Apicomplexa based on Oxford Nanopore Technologies sequencing platform using the 18S gene of fourteen Apicomplexa-positive samples collected in French Guiana. Sequencing reads were then analysed with MetONTIIME pipeline. Thanks to a scoring rule, we were able to classify as Apicom-plexa-positive 10 samples out of 14 and reveal the presence of co-carriages. The same samples were also sequenced with Illumina platform, for validation purposes. On samples identified as Apicomplexa-positive by both platforms, a strong positive correlation at up to genus level was reported. Overall, the presented workflow represents a reliable method for Apicomplexa detec-tion, which may pave the way for more comprehensive biomonitoring of zoonotic pathogens.

The process industry is confronted with rising demands for flexibility and efficiency. One way to achieve this are modular process plants that consist of pre-manufactured modules with their own decentralized intelligence. Plants are then composed of these modules as unchangeable building blocks and can be easily re-configured for different products. Condition monitoring of such plants is necessary, but available solutions are not applicable. The authors suggest an approach in which model-based symptoms are derived from few measurements and observers that are based on manufacturer knowledge. The comparisons of redundant observers lead to residuals that are classified to obtain symptoms. These symptoms can be communicated to the plant control and are inputs to an easily adaptable diagnosis. The implementation and validation at a modular mixing plant showcases the feasibility and the potential of this approach.

Additive Manufacturing (AM) simplifies the fabrication of complex geometries. Its scope has rapidly expanded from the fabrication of pre-production visualization models to the manufacturing of end use parts driving the need for better part quality assurance in the additively manufactured parts. Machine learning (ML) is one of the promising techniques that can be used to achieve this goal. Current research in this field includes the use of supervised and unsupervised ML algorithms for quality control and prediction of mechanical properties of AM parts. This paper explores the applications of supervised learning algorithms - Support Vector Machines and Random Forests. Support vector machines provide high accuracy in classifying the data and is used to decide whether the final parts have the desired properties. Random Forests consist of an ensemble of decision trees capable of both classification and regression. This paper reviews the implementation of both algorithms and analyzes the research carried out on their applications in AM.

Findings on diet-health relationships have led many people to include healthier food items (including snacks) in their diets, e.g. those containing probiotic microorganisms. The purpose of this study was to compare two methods to produce probiotic freeze-dried banana slices - one of them consisting of impregnating slices with a suspension of probiotic Bacillus coagulans, the other based on coating the slices with a starch dispersion containing the bacteria. Both processes have resulted in viable cell counts above 7 log ufc.g-1, although the presence of the starch coating has avoided a significant loss of viability on freeze-drying. The coated slices were less crispy than the impregnated ones, according to the shear force test results. However, the sensory panel (with more than 100 panelists) have not perceived significantly texture differences. Both methods have presented good results, in terms of probiotic cell viability and sensory acceptability (the coated slices having been significantly more accepted than the non-probiotic control slices).

Over the past few decades, the growth of the urban population has been remarkable. Nowadays, 50% of the population lives in urban areas, and forecasts point that by 2050 this number will reach 70%. Today, 64% of all travel made is within urban environments and the total amount of urban kilometers traveled is expected to triple by 2050. Thus, seeking novel solutions for urban mobility becomes paramount for 21st century society. In this work, we discuss the performance of vehicular networks. We consider the metric Delta Network. The Delta Network characterizes the connectivity of the vehicular network through the percentage of travel time in which vehicles are connected to roadside units. This article reviews the concept of Delta Network and extends its study through the presentation of a general heuristic based on the definition of scores to identify the areas of the road network that should receive coverage. After defining the general heuristic, we show how small changes in the score computation can generate very distinct (and interesting) patterns of coverage, each one suited to a given scenario. In order to exemplify such behavior, we propose three deployment strategies based on simply changing the computation of scores. The results show that the strategies derived from the general heuristic are very interesting, all of them deploying roadside units in a circle pattern around the traffic epicenter.

Abstract Aim: The study aimed to evaluate the clinical laboratory features of moderate and severe COVID-19 patients among a cohort of the Egyptian population. The study also aimed to assess the accuracy—sensitivity, specificity, and area under the curve (AUC) of various detected parameters in predicting the severity of COVID-19 infection. Patients and methods: One hundred diagnosed COVID-19 patients and fifty healthy participants in total were involved in current study. COVID-19 patients were categorized based on how severe their symptoms into two groups. Estimates were made for serum levels of alanine aminotransferase (ALT), aspartate aminotransferase (AST), albumin, lactate dehydrogenase (LDH) and C-reactive protein (CRP) as well as white blood cells (WBCs) count, lymphocytes count, and hemoglobin content (Hb) content. Results: COVID-19 patients displayed increased serum levels of liver enzymes and CRP as well as WBCs count when compared to healthy individuals. On the other hand, Hb content, lymphocytes count, and albumin level fell in all COVID-19 patients. The severe group showed a statistically significant rise in liver enzymes, WBCs, and CRP levels, compared with moderate group. WBCs and lymphocytes counts were closely correlated with age, ALT, LDH, and CRP in all cases. WBCs and lymphocytes counts also had a negative correlation with albumin Level. Additionally, WBCs count, lymphocytes count, LDH activity and CRP level have higher AUC in severe than in moderate cases. WBCs count, LDH activity and CRP level have AUC above 0.80 in the severe group. Conclusion: The current investigation found a significant correlation between WBCs count, lymphocytes count, CRP level and liver injury in COVID-19 patients. WBCs count, lymphocytes count, LDH activity and CRP level were effective indicators for determining the severity of COVID-19.

Keywords: Marine Coasts; Protected Areas; Defense and Conservation; Asbestos Cement Materials; Wastes; Contamination; Human Health Risk; Medical Geology.

Here are given tight probabilistic inequalities that provide nearly best estimates for the Csiszar's f-divergence. These use the right and left psi -Hilfer fractional derivatives of the directing function f. Csiszar's f- divergence or the so called Csiszar's discrimination is used as a measure of dependence between two random variables which is a very essential aspect of stochastics, we apply our results there. The Csiszar's discrimination is the most important and general measure for the comparison between two probability measures. We give also other applications.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

Metabarcoding of prokaryotic and fungal ribosomal DNA was used to describe the microbial communities in soils of remnant equatorial rainforest, maize-bean intercrop, and sugarcane in western Kenya. Cropping systems influenced the microbial community composition and functional traits (energy source and nutrient cycling) of bulk soil in each crop. Microbial richness and diversity tended to increase with cultivation intensity. Soil of maize-bean intercrop had lower percentages and sugarcane had higher percentages of unique amplicon sequence variants of both bacteria and fungi compared to the remnant forest. Functional traits were altered by cultivation intensity. Compared to remnant forest soils, maize-bean intercrop soil had lower percentages of aerobic chemoheterotrophic bacteria and higher percentages of N-cycling bacteria, while sugarcane had higher percentages of aerobic chemoheterotrophic bacteria and lower percentages of N-cycling bacteria. In the face of increasing forest loss and pressures for agricultural productivity, this landscape provides a rich site for studying the impacts of cropping systems on soil health.

High incidence of epithelial malignancies in HIV-1 infection is associated with co-infection with oncogenic viruses, such as high-risk human papillomaviruses (HR HPVs), most often HPV16. A collaboration between HIV-1 and HR HPVs in the malignant transformation of epithelial cells exposed to both viruses have long been anticipated. Here, we delineated the effects on in vitro and in vivo properties of HPV16-infected cervical cancer cells of HIV-1 reverse transcriptase. Epidermoid carcinoma Ca Ski cells were made to express RT of HIV-1 clade A (RT_A) or Green Fluorescence Protein (GFP) by lentiviral transduction, subclones with one or six copies of RT_A and six copies of GFP DNA were generated. Expression by subclones of GFP was assessed by flow cytometry, and of RT_A, by Western blotting. Cells were assessed for the levels of mRNA of the RT_A, E6 and its isoforms, and cellular factors characterizing oxidative stress, and EMT by the real-time PCR. Parameters of glycolysis and mitochondrial respiration were assessed by Seahorse technology. Subclones were surveyed for the changes in cell cycle, doubling time, migration capacity, clonogenic activity and for the capacity to form tumors in nude mice. Ca Ski RT_A produced 20-55 fg of RT_A per cell. Expression of RT_A caused a proportional increase in the expression of E6*I isoform. In Ca Ski, RT_A suppressed mitochondrial respiration and oxygen consumption, and increased glycolysis. Compared to parental cells and GFP control, transcription in Ca Ski RT_A of epithelial (E-CADHERIN) state marker was increased, and of mesenchymal (VIMENTIN) decreased, indicating acquisition by cells of the hybrid epithelial/mesenchymal (E/M) phenotype. While Ca Ski GFP and Ca Ski RT_A with one gene insert had reduced migration rate, decreased clonogenic activity in vitro, and diminished capacity to form tumors in nude mice, increase in RT_A copicity/expression mitigated these effects. Altogether, expression of HIV-1 RT_A gave Ca Ski cells the plasticity required to overcome negative effects of lentiviral transduction and potentially increased their tumorigenicity.

Radio astronomical observations at millimeter and submillimeter wavelengths are a very important tool of astrophysical research. However, there is a huge area in the northern Eurasia, including the whole Russian territory, which lacks sufficiently large radio telescopes effectively operating at these wavelengths. In this review we describe our long-term efforts to find suitable sites for such radio telescopes in this area, that is, sites with good atmospheric transparency at millimeter and submillimeter waves. We describe methods and instruments used for measurements and evaluations of the atmospheric opacity. They include special radiometric systems, which are used for estimations of the atmospheric opacity from the sky brightness measurements. Evaluation of the precipitable water vapor from such measurements by the artificial neural network is discussed. Alternative approaches use global atmospheric models and signals of the Global Navigation Satellite Systems. To date, a long-term radiometric monitoring has been performed at several candidate sites and atmospheric conditions for many sites have been evaluated using global atmospheric models. Several sites with the best atmospheric transparency at millimeter and submillimeter wavelengths have been selected. They can be effectively used for astronomical observations at least in the major atmospheric transparency windows at 1.3 mm and 0.85 mm. These results can be also used for space communications and radar systems.