Ipomoea batatas L. (IBL) has gained significant popularity as a complementary therapy or herbal medicine in the treatment of anti-diabetes. The objective of this review is to examine the mechanism of action of flavonoid compounds found in IBL that can activate GLP-1 as an anti-diabetic agent. The review article refers to PRISMA guidelines. The literature search was conducted using electronic databases such as Crossref, Pubmed, Scopus, and Science Direct. The search query was based on specific keywords, including Ipomoea batatas OR sweet potato AND anti-diabetic OR hypoglycemic. A total of 1055 articles were found, but only 32 articles were selected for further review based on inclusion and exclusion criteria. IBL contains various compounds, including phenolic acid, flavonols, flavanols, flavones, and anthocyanins, which exhibit activity against anti-diabetes. Flavonols, flavonols, and flavones belong to a group of flavonoids that possess the ability to form complexes with AlCl3 and Ca2+. Retention of Ca2+ within intracellular L cells, resulting in the release of GLP-1. Flavonols, flavones, and flavone groups have been found to strongly interact with DPP-IV, which inhibits the degradation of GLP-1. This mechanism effectively prolongs the half-life of GLP-1 in the systemic system, thereby contributing to the anti-diabetic activity of IBL

Lake Rawa Besar is an urban lake surrounded by dense settlements and market area. Currently Lake Rawa Besar is experiencing physical and ecology strain. This research’s objectives are to determine the levels of sediment and nutrient, the distribution, also the relation to land use and human activities producing pollutant. Field surveys with 30 sample points and observations was needed scattered within the lake. Measuring the value of each parameter is carried out in national standardized laboratory. The result shows that sediment load of TDS is still below the standard limit for clean water, while TSS levels in the middle of lake exceed the standard limit. Nutrient loads, spesifically nitrate and phospate levels is below the standard limit. While turbidity and BOD levels have a uniform distribution pattern in the lake, exceed the standard limit for clean water, and have a positive correlation. High levels of turbidity and BOD are caused by household waste and human activities producing organic waste such as tofu factory, fowl manure, and garbage dump. Small sewage goes into the lake mediates pollutants inflow. Attention is needed by nearby people, also for the government, to sustain the ecological condition of the lake.

Flood disasters have become an annual occurrence along the East Coast of North Sumatra (ECNS) and Medan City. Numerous studies have examined the causal factors flood disasters in this area, such as changes in land use, drainage issues, and population growth, but the intensity of flood disasters continues to rise. In this research, we focused on evaluating the unexplored factors of land subsidence and rising sea levels in this region. Our investigation uses multi-sensor satellite data and field surveys to conduct an assessment of the rate of land subsidence and sea level rise and assess their implications on flood disasters. This study highlights the potential of multi-sensor satellite data as a primary resource for assessing flood disasters in coastal areas and densely populated large cities. Furthermore, we propose a solution to reduce the negative impact of flood disasters by by engaging local communities and environmental enthusiasts in mangrove reforestation along the coastline.

- Early and accurate detection of pneumonia from chest X-ray images is crucial for timely treatment and patient care. In study presents a robust computational framework leveraging the CheXnet algorithm, a deep learning model, to identify pneumonia from chest X-rays. Developed a neural network architecture trained on a substantial dataset of chest X- ray images labeled as 'Normal' and 'Pneumonia'. The user- friendly interface of the system allows for seamless uploading of images, with the model subsequently providing predictions, a confusion matrix, accuracy metrics, and layer activations visualizations. The algorithm's performance was rigorously evaluated, with a confusion matrix indicating a high number of true positives and true negatives. Specifically, the model detected pneumonia with an accuracy of 92.47%, as shown by the results displayed in the system's interface. The precision, recall, and F1-score for pneumonia detection were 0.90, 0.96, and 0.93 respectively, with the overall system achieving an accuracy of 0.91 across the test set of 624 images. Visualizations of the neural network layers reveal the complex feature mappings the model uses to differentiate between normal and pathological findings. These insights could be vital for enhancing the interpretability of deep learning models in medical diagnostics. The Results indicate that the CheXnet-based neural network is a promising tool for automating pneumonia detection in clinical settings, which can assist radiologists in the diagnostic process and potentially improve patient outcomes through earlier intervention.

Cognitive deterioration caused by illness or aging often occurs before symptoms arise, and their timely diagnosis is crucial to reducing its medical, personal, and societal impacts. Brain-Computer Interfaces (BCIs) stimulate and analyze key cerebral rhythms, enabling reliable cognitive assessment that can accelerate diagnosis. The BCI system presented analyzes Steady-State Visually Evoked Potentials (SSVEPs) elicited in subjects of varying age to detect cognitive aging, predict its magnitude, and identify its relationship with SSVEP features (band power and frequency detection accuracy), which were hypothesized to indicate cognitive decline due to aging. The BCI system was tested with subjects of varying age to assess its ability to detect aging-induced cognitive deterioration. Rectangular stimuli flickering at theta, alpha, and beta frequencies were presented to subjects, and frontal and occipital EEG responses were recorded. These were processed to calculate detection accuracy for each subject and calculate SSVEP band power. A neural network was trained using the features to predict cognitive age. The results showed potential cognitive deterioration through age-related variations in SSVEP features. Frequency detection accuracy declined after age group 20–40 and band power, throughout all age groups. SSVEPs generated at theta and alpha frequencies, especially 7.5 Hz, were the best indicators of cognitive deterioration. Here, frequency detection accuracy consistently declined after age group 20-40 from an average of 96.64% to 69.23%. The presented system can be used as an effective diagnosis tool for age related cognitive decline.

Abundant animal manure in livestock areas has the potential to be used as organic fertilizer which can restore soil fertility by turning it into compost and biochar. The goal of this study was to as-sess how well soil fertility and red chili yield might be increased by using biochar and poschar made from various animal wastes. In this investigation, a factorial pattern and randomized block design were used. The first factor was the biochar treatment type, which included no biochar, biochar made from cow manure, biochar made from goat manure, and biochar made from chicken manure. The second factor was the type of poschar, which included no poschar, poschar made from cow manure, poschar made from goat manure, and poschar made from chicken manure. The findings of this study suggest that using biochar in conjunction with poschar can significantly improve soil parameters such as soil water content, pH, EC, humic acid, fulvic acid, C, N, P, K, and CEC. Red chilies grow and yield more per hectare when different types of biochar and poschar are used. The use of biochar from cow manure together with poschar from chicken manure shows the best agronomic effectiveness.

The global energy crisis has lead researchers explore other sources of energy like wind, resulting in a wide acceptance of wind turbines. Vertical axis wind turbines (VAWT) more suitable for small scale application in urban conditions than their horizontal-axis counterparts. A Helical bladed VAWT would reduce the ripple effect when compared to Straight bladed VAWT. The effect of the blade helix angle on the aerodynamic performance of VAWT using 3D numerical simulations is studied. Turbulence modelled using 4-Equation transition SST k-w model. Three different helix angles of 60, 90 and 120 of a 3 bladed VAWT operating across different tip speed ratios were studied. The 60 helical bladed VAWT was found to perform better than all other helical bladed and straight bladed VAWT. Standard deviation of the moment coefficient generated by a blade plotted against 360 of azimuth rotation revealed that the ripple effect on the shaft produced by cyclic loading of the straight blade is considerably reduced upon introduction of helix angle, with 120 helical blade giving lowest standard deviation. The analysis has been done for the percentage of power generated by each quartile of flow and the contribution of each section of the blade. A comparative study was also conducted between different helical bladed VAWT and straight bladed VAWT. Flow feature analysis also revealed the reasons behind secondary peaks and the performance improvement when tip speed ratio increases. Wake structure analysis and flow contours were also studied for a better understanding of the flow field.

Although a lot of research has been carried out on hand sanitizer as an effort to prevent Covid-19, there is still limited research on non-alcoholic hand sanitizer lotion from the brown algae Scytosiphon lomentaria (S. lomentaria) as a raw material that provides antibacterial effects and maintains healthy skin. Therefore, this study aimed to analyze microbial inhibitory ability, physical and chemical characteristics of hand sanitizer lotion made from S. lomentaria algae. S. lomentaria powder was tested for phytochemicals, total phenolic content, free radical scavenging activity (IC50), and antibacterial tests. S. lomentaria slurry was prepared by adding distilled water (1:1) for lotion preparations in four treatment groups, such as normal control (lotion base without adding algae), lotion with the addition of algae 20%, 30%, and 40%. The lotion preparations for each treatment group were tested for antibacterial activity of Staphylococcus aureus and Escherichia coli, phytochemicals, pH, adhesion, spreadability, homogeneity, emulsion type, and hedonic. S. lomentaria powder contains bioactive polyphenolic compounds with a total phenolic content of 117.70±1.40 mg GAE/g dry weight and an IC50 value of 455±3.4 ppm, while lotion with the addition of S. lomentaria contains polyphenols and saponins The best treatment was shown by 40% S. lomentaria hand sanitizer lotion with inhibition of 6.30 ± 0.64 mm E. coli, 6.85 ± 1.12 mm S. aureus, hedonic test for color, texture and absorption with likes to likes very much level, neutral pH, greenish-white color, O/W emulsion type, high adhesion, homogeneous, and easily absorbed by the skin. This research can be an alternative reference in making non-alcoholic hand sanitizer lotion that is safe for the skin.

People have always hoped to be able to fill an entire plane with ``single unit cells'' without periodicity. This wish was realized after the mathematician discovered a 13-sided ``single unit cell'' named `einstein'. These non-periodic tessellations generally exhibit anisotropic properties, making them superior in terms of mechanical performance compared to periodic structures. From the perspective of information entropy, the reason behind the improved mechanical properties of these structures is the higher entropy associated with non-periodic configurations. To quantify the disorder of non-periodic structures, we propose an entropy expression for the `einstein' metamaterial. To demonstrate the mechanical properties of these high-entropy structures, we fabricate specimens using 3D printing and conducte mechanical experiments. For comparative analysis, we also use ABAQUS to perform finite element analysis of the problem. The research results reveal that the mechanical properties of high-entropy structures created by the non-periodic stacking of cells are significantly improved compared to those of low-entropy structures created by periodic stacking. The conclusions drawn from the study of individual issues are generalizable and may be of assistance in future material and structural design. \end{abstract}

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Traditional aquaculture systems appear to be confronted with the high total ammonia nitrogen (TAN) produced during production, which can be harmful to aquatic life. As the demand for global fish production continues to increase, farmers should adopt Recirculating Aquaculture Systems (RAS) to improve production. The biofilter plays a vital role in ammonia removal. However, the drawback of the biofilter operation is needed an automatic and controlled system with a water quality monitoring system to guarantee optimal performance. RAS utilize a monitoring and control system to maintain the water quality and control the biofilm growth in the biofilter to reduce the ammonia. Therefore, this study focuses on developing a water quality monitoring and control system to achieve optimum biofilm performance. From 35 days of the experiment, the water quality was controlled at a level save for the aquatic environment, such as dissolved oxygen, pH, temperature, and TDS. Thus, the highest TAN removal efficiency is 50% when biofilm thickness reaches 119.88 µm.

A new circuit model of the self-powered device for heart rate measurement is presented in this paper. This device consists of piezoelectric energy harvester (PEH), power management circuit (PMC) with energy storage, microcontroller, Photoplethysmography (PPG) sensor, and Wi-Fi module. The PEH is placed under the insole to harvest the pressure energy from human foot-step to generate ac power. In our model, a PEH is represented by sine voltage source, where its parameters were taken from experiments with 20 volunteers. The PMC is simplified by a switch with gain δ placed in series with the main circuit. The model of the main circuit is RC elements in parallel, where C is the capacitance of the storage device, and R is the equivalent parallel resistance of the microcontroller, PPG sensor, and Wi-Fi modules, respectively. The value of R depends on the power and current absorbed by those modules during sleep, deep sleep, sense, and transmit modes which collected from the datasheet. Finally, the proposed circuit model of the self-powered device was built and simulated in SPICE. The simulation results were compared with the laboratory experiment using commercial devices. Based on the results, the proposed model had small gaps compared to the real self-powered devices in terms of average current, voltage, power and efficiency.

This study aims to develop a novel retention method combining the retrievability of the screw retention method with the ideal occlusal table and the aesthetics capability of cement retention. Coping was developed to have lateral screw access allowing the screw to lock coping using lateral forces from screw tightening and friction between the tip of the screw and the sandblasted surface of an abutment. Sandblasting parameters varied based on particle size. Results show a positive correlation to surface roughness and indicate a positive correlation to retention force. The highest surface roughness and retention force result was shown by groups that were sandblasted using 686 μm of aluminum oxide. Experiment on the tightening strength of 48 subjects measured in simulated conditions similar to assembly conditions of lateral screw retention implant resulted in a mean of 69.75 Nmm with the highest and lowest values of 120.67 Nmm and 34.67 Nmm. This result became the basis of tightening torque variation. Each group's retention capability is measured and compared to cement-retained dental implants. Results show that tightening torque correlates positively with retention force, with the highest average retention score showed by lateral screw retained under tightening torque of 200 Nmm with 317.87 N higher than cement-retained.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

This study evaluated the impact of didactic videos and service user testimonial videos on mental illness stigma among medical students. Two randomized controlled trials were conducted in Nepal. Study 1 examined stigma reduction for depression. Study 2 examined depression and psychosis. Participants were Nepali medical students (Study 1:n=94, Study 2:¬n=213) randomized to three conditions: a didactic video based on the mental health Gap Action Programme (mhGAP), a service user video about living with mental illness, or a control condition with no videos. In Study 1, videos only addressed depression. In Study 2, videos addressed depression and psychosis. In Study 1, both didactic and service user videos reduced stigma compared to the control (F2,91=6.37, p=0.003). In Study 2 (depression and psychosis), there were no differences among the three arms (F2,210=2.07, p=0.13). When comparing Study 1 and 2, there was greater stigma reduction in the service user video arm with only depression versus service user videos with depression and psychosis (t(31)=-3.04, p=0.005). In summary, didactic and service user videos were associated with decreased stigma when content addressed only depression. However, no stigma reduction was seen when including depression and psychosis. This calls for different strategies based on types of mental illnesses. ClinicalTrials.gov identifier: NCT03231761

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

The Smartphone industry has expanded significantly over the last few years. According to the available data, each year, a marked increase in the number of devices in use is observed. Most consumers opt for Smartphones due to the extensive number of software applications that can be downloaded on their devices, thus increasing their functionality. However, this growing trend of application installation brings an issue of user protection, as most applications seek permission to access data on a user’s device. The risks this poses to sensitive data is real to both corporate and individual users. While Android has grown in popularity, this trend has not been followed by the efforts to increase the security of its users. This is a well-known set of problems, and prior solutions have approached it from the ground up; that is, they have focused on implementing reasonable security policies within the Android’s open-source kernel. While these solutions have achieved the goals of improving Android with such security policies, they are severely hampered by the way in which they have implemented them. In this work, a framework referred to as CenterYou is proposed to overcome these issues. It applies a pseudo data technique and a cloud-based decision-making system to scan and protect Smartphone devices from unnecessarily requested permissions by installed applications and identifies potential privacy leakages. The current paper demonstrated all aspects of the CenterYou application technical design. The work presented here provides a significant contribution to the field, as the technique based on pseudo data is used in the actual permissions administration of Android applications. Moreover, this system is user and cloud-driven, rather than being governed by over-privileged applications.

In this study, the physical properties of briquettes produced from two different biomass feedstocks (sawdust and date palm trunk) and different plastic wastes were investigated, without using any external binding agent. The biomass feedstocks were blended with different ratios of two WEEE plastics (halogen-free wire and print circuit boards (PCB)) and automotive shredder residues (ASR). The briquettes production is studied at different waste proportions (10-30%), pressures (22-67 MPa) and temperatures (room-130 ˚C). Physical properties as density and durability rating were measured, usually increasing with temperature. Palm trunk gave better results than sawdust in most cases, due to its moisture content and the extremely fine particles that are easily obtained.

THz band-pass filters were fabricated by laser ablation of micro-foils of stainless steel and Kapton. Their spectral performance was tested in transmission and re- flection at the THz beamline at the Australian Synchrotron (AuSy). A 25 μm Kapton film performed as a Fabry-Pérot etalon with a free spectral range of FSR = 119 cm−1, high finesse Fc ≈ 17, and was tuneable over ~10 μm (at ~5 THz band) with β = 30° tilt. The structure of the THz beam focal region as extracted by the first mirror (slit) shows a complex polarisation-wavelength- position dependence across the beam. This is important for polarisation sensitive measurements (in transmission and reflection) and requires normalisation at each orientation of linear polarisation.

In a previous study we could show a change of membrane morphology and gas separation performance by varying the recipe of a casting solution based on polysulfone in a determined solvent system. Although all results were very reproducible, all used solvents were harmful and not sustainable. In this study therefore, the solvents tetrahydrofuran (THF) and N,N-dimethylacetamide (DMAc) are replaced by the more sustainable solvents 2-methyl-tetrahydrofuran (2M-THF), N-butyl pyrrolidinone (NBP) and cyclopentyl methyl ether (CPME). The gas permeation performance and for the first time morphology of the membranes before and after solvent replacement were determined and compared by single gas permeation measurements and SEM microscopy. It is shown, that THF can be replaced by 2M-THF and NBP without decreasing the gas permeation performance. With CPME replacing THF no membranes were formed. Best gas permeation results showed systems with 2M-THF as THF alternative. Permeances for the tested gases oxygen (O2), nitrogen (N2), carbon dioxide (CO2) and methane (CH4) were 2.66·10-4, 3.89·10-5, 1.53·10-3 and 4.52·10-5 mL(STP)/cm²·min·bar, respectively. permselectivities of those membranes for the gas pairs O2/N2, CO2/N2 and CO2/CH4 were 6.7, 38.3 and 34.0, respectively. When additionally replacing DMAc in the solvent system no or only porous membranes were obtained, even if the precipitation procedure was adjusted. These findings indicate that a complete replacement of the solvent system without affecting the membrane morphology or gas permeation performance is not possible. By varying the temperature of the precipitation bath an easy adjustment to mechanically stable PSU membranes is possible, if just THF was replaced by 2M-THF.

This paper reports for the first time on the production of probiotic alcoholic and non-alcoholic rosé wines with enhanced health benefits made with Saccharomyces cerevisiae var. boulardii probiotic yeast. The alcohol, sugar, volatile acidity lactic and malic acid contents were assessed for S. cerevisiae var. boulardii before and after fermentation and distillation and compared with a conventional Saccharomyces cerevisiae (ex-bayanus) yeast. The free amino nitrogen and gluconic acid concentrations in the musts were determined. Yeast viability was evaluated after fermentation and distillation as a function of time (0, 15 days, 3 months and 6 months) both at room temperature (25±0.5ºC) and refrigerator temperature (4±0.5ºC). The results obtained showed that the probiotic rosé wine produced with S. cerevisiae var. boulardii possesses the typical values and sensory attributes of other commercial wines produced with S. cerevisiae (ex-bayanus). The probiotic S. cerevisiae var. boulardii yeast survives the high alcohol content produced during fermentation and vacuum distillation. The study also showed that this probiotic rosé wine stored either at room temperature or in a refrigerator keeps its probiotic viability for at least six months, which makes it a promising for large-scale production, in which long storage times are required by both producers and consumers.

Joints between walls are very important for structural analysis of each masonry building at the global and local level. This issue was often neglected in case of traditional joints and relatively squat walls. Nowadays the issue of wall joints is becoming particularly important due to the continuous strive for simplifying structures, introducing new technologies and materials. Eurocode 6 and other standards (USA, Canadian, Chinese, and Japanese) recommend inspecting joints between walls, but no detail procedures have been specified. This paper presents our own tests on joints between walls made of autoclaved aerated concrete (AAC) masonry units. Tests included reference models composed of two wall panels joined perpendicularly with a masonry bond (6 models), traditional steel and modified connectors (12 models). A shape and size of test models and structure of a test stand were determined on the basis of the analysis of the current knowledge, pilot studies and numerical analyses of FEM. The analysis referred to the morphology and failure mechanism of models. Load-displacement relationships for different types of joints were compared and obtained results were referred to results for reference models. A mechanism of cracking and failure was found to vary, and clear differences in behaviour and load capacity of each type of joints were observed. Individual working phases of joints were determined and defined, and the empirical approach was suggested to determine forces and displacement of wall joints.

Alum sludge, an inevitable by-product from the water purification process, which had been applied as substrates in some constructed wetlands with good performance, especially for phosphorus (P) adsorption. The raw alum sludge is like clay lump with irregular shape and has a leaching concern used in the water. For a better reuse, herein, sludge was fired to produce alum sludge ceramsite (ASC) with a uniform spherical shape via four-step process of kneading sludge ball, air drying, preheating at 400°C for 10 min and firing at 600℃ for 5 min. Thereafter the physicochemical properties and P adsorption ability of ceramsite were investigated. Through XRD and FT-IR tests, there was no obvious difference between ASC and air-dried alum sludge ball (adASB) on the phase structure, but a certain amount of Al-OH group loss on the surface of ASC. The structure of ASC was still amorphous as same as adASB, while ASC possessed more micropore structure and bigger specific surface area than those of adASB. Adsorption experiments showed the P adsorption behaviors of ASC and adASB were much similar, and their adsorption kinetics all accorded with the two-step adsorption kinetics rate equation and pseudo-second-order kinetics equation. The maximum adsorption capacities of ASC and adASB fitted by Langmuir model were 1.66 mg/g and 1.89 mg/g respectively. It should be pointed that, compared with other adsorbents, ASC produced in this study still had a higher ability to adsorb P. Therefore, ASC should have a great application potential for P removal in the wastewater treatment in China.

In several Indonesian tropical cities, such as Makassar City, frequent flooding during the peak rainy season poses a significant challenge. This study seeks to address this issue by devising effective policies to reduce flood exposure. The main obstacle lies in accurately determining the flood inundation area. To overcome this, the study utilizes multiple satellite data sources on a cloud platform, integrating them with land use data, and DEM data, aligning these with the local government's urban land use plan and existing drainage networks. The research aims to quantify the affected area, identify the predominant inundated land cover, and assess the efficiency of Makassar's drainage system and urban land use plan. The study reveals that an uncoordinated drainage system in the Tamalanrea, Biringkanaya, and Mangala sub-districts results in severe flooding, encompassing a total area of 35.28 km². The most affected land use type is cultivation, constituting approximately 43.5% of the flooded area. Furthermore, 82.26% of the urban land use plan, covering 29.02 km², is submerged. It is imperative for the local government and stakeholders to prioritize the enhancement of drainage systems and urban land use plans, particularly in low-lying and densely populated regions

Natural fibers have been widely used as a reinforcing material for the construction of drones. The main goal of this review is to identify a biodegradable natural fiber material that can be built for Unmanned Aerial Vehicles (UAVs). The review shows that natural fibers such as kenaf and PALF can be used as an alternative composite material, particularly for multifunctional applications where their smaller weight and less expensive characteristics make them incredibly realistic. This review also discusses the mechanical properties, advantages and disadvantages, and fabrication of the composites.

In the present trend of constructing taller and longer structures, the application of lightweight aggregate concrete is becoming an increasing important advanced solution in the modern construction industry. In engineering practice, the analysis of lightweight concrete elements is performed using the same algorithms used for normal concrete elements. As an alternative to traditional engineering methods, nonlinear numerical algorithms based on constitutive material models may be used. The paper presents a comparative analysis of curvature calculations for flexural lightweight concrete elements, incorporating analytical code methods EN 1992-1 and ACI 318-14, as well as a numerical analysis using the constitutive model of cracked tensile lightweight concrete recently proposed by the authors. To evaluate the adequacy of the theoretical predictions, experimental data of 51 lightweight concrete beams tested during five different programmes were collected. A comparison of theoretical and experimental results showed that the most accurate predictions are obtained using numerical analysis and the constitutive model proposed by the authors. In the future, the latter algorithm can be used as a reliable tool for improving the design standard methods or numerical modelling of lightweight concrete elements subjected to short-term loading.

Direct laser writing based on non-linear 3D nanolithography (also known as 3D laser lithography, 3DLL) is a powerful technology to manufacture polymeric micro-optical components. However, practical applications of these elements are limited due to the lack of knowledge of their optical resilience and durability. In this work, we employ 3DLL for the fabrication of bulk (i.e. fully filled) and woodpile structures out of different photopolymers. We then characterize them using S-on-1 laser induced damage threshold (LIDT) measurements. In this way, quantitative data of LIDT values can be collected. Furthermore, this method permits to gather damage morphologies. The results presented in this work demonstrate that LIDT values depend on the material and the geometry of the structure. Bulk non-photosensitized hybrid organic-inorganic photopolymer SZ2080 structures are found to be the most resilient with a damage threshold being of 169±15 mJ/cm².

Chivalry is a concept that is both familiar and distant to many Japanese. There is no other social class in the world that resembles knights as much as the samurai in Japan. However, why is there such a gap between the behaviour of knights and samurais, even though they are both a social class with honor? This paper compares chivalry and Bushido, the Japanese Samurai code.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

In this experimental report the biocompatibility of elastomeric scaffold structures made via stereolithography employing table-top 3D printer (Ember, Autodesk) and commercial resin FormLabs Flexible (FormLabs) was studied. The samples were manufactured using standard printing and development protocol, which is known to inherit cytotoxicity due to remaining non-polymerized remaining monomers, despite the polymerized material being fully biocompatible. Additional steps were taken to remedy this problem: the fabricated structures were soaked in isopropanol and methanol for different conditions (temperature, duration) in order to leach out the non-polymerized monomers. Also printed structures were UV exposed to assure maximum polymerization degree of the material. Post-processed structures were seeded with myogenic stem cells and the number of live cells was evaluated as an indicator for the material biocompatibility. The straightforward post-processing protocol enhances the biocompatibility by 7 times after 7 days soaking in isopropanol and methanol and is comparable to control (glass and polystyrene) samples. This proposes the approach as a novel and simple method to be widely applicable for dramatic cytotoxicity reduction of optically 3D printed micro-/nano-scaffolds for biomedical applications.

The allocation for the use of Deconcentration Funds focuses on the seven priority health programs listed in the Regulation of the Minister of Health for the Republic of Indonesia. Therefore, this study aims to formulate a budget allocation for deconcentration funds in the health sector. Secondary data were analyzed using reports from the Ministry of Health for five years (2014-2018) on the Human Development Index (HDI), population, area, number of health workers, as well as amount and percentage for the realization of deconcentration funds. The results showed that the variables which had a significant effect were the number of districts/cities, the area, and HDI, while those without a significant effect were population, the number of health workers, and the percentage of budget realization. Political factors and regional commitment to implementing as well as using the budget were shown to also affect the deconcentration of funds both from the central and regional sources. Generally, deconcentration funds are used for non-physical tasks, including coordinating and synchronizing planning, facilitation, technical guidance, training, outreach, supervision, investigations and surveys, direction, and control. Based on the results, the budget allocation for deconcentration funds for health development needs to be calculated according to regional capacities by considering the number of districts/cities, land area, and the HDI.

The present study concerns the application of electrochemical chloride extraction to concrete designed with partial replacements of Ordinary Portland Cement (OPC) from different binders, namely ground granulated blast furnace (GGBS), pulverized fly ash (PFA) and Silica Fume (SF), to attend the need of corrosion repair for modern constructions. Electrochemical Chloride Extraction (ECE) was applied to the specimens at a current density of 2A/m2 for 4 weeks. The chloride types and binding mechanisms appeared to have important implications on the different performance of treatment perceived for all binders. Considering total chlorides, removal was more significant for OPC and GGBS when compared to others. The main difference noted was that for GGBS the removal of bound chlorides was more significant due to a possible release of adsorbed chlorides from the silicate hydrates, present at higher intensities in this case. However, even though GGBS had greater rates of bound chloride removal it had still the same percentage as OPC for total efficiency due to the fact that in OPC the removal of free chlorides is more expressive.

This paper presents the results of the investigation of composite sinters W-TiB2 which were used as an electrode in the process of electro-spark deposition (ESD) and the examination of the deposited layers. The scope of the study includes detailed characteristics of powder mixtures, composite sinters made using the spark plasma sintering method (SPS) and layers deposited in the electro-spark process. The ESD process, using the W+30 vol.% TiB2 electrode, was carried out using an automated device. The substrates were made of copper and aluminium. The topography analysis of the surfaces of the composite layer and the evaluation of their wear resistance properties are also presented. The analysis of the results of research showed the possibility to obtain, using the SPS method, composite materials of good quality, which can be used as electrodes in the ESD process. The obtained layers had increased wear resistance in relation to the substrate material.

Using the headphone jack of a mobile phone, the proposed device connects mobile music playback through a customized red laser pointer that is cascaded to batteries and the 3.5-mm stereo plug. The red laser pointer flashes according to the frequency of the music currently playing on the mobile phone. The self-made laser pointer which wavelength is 630–650 nm and maximum output is 5 mw and it will light up when the smart phone’s music starts playing at a music frequency matching the light frequency. The frequency signal of the light received by a solar panel is converted to an electrical analog signal, and the analog current signal is amplified through the energy conversion panel and then output to the direct current motor. The motor shaft does not rotate under a small current, but rather only slightly vibrates according to the magnitude of the currents’ analog frequency. Through gripping the motor shaft with teeth, users can transmit audio to the auditory ossicles (i.e., malleus, incus, and stapes) through the dentary bones. After receiving a music signal, the auditory ossicles enable people with congenital or acquired hearing loss to access external audio.

The experimental verification for the computational method sometimes varies due to numerous factors such as the manufacturing process and the materials' property change due to environmental aspects. In this work, we performed verification of experimental and computational evaluation of a hybrid composite moderate thick plate. The experiment was performed with simplistic approaches and without the advanced tools of preparing composite materials. This is due to the fact that most of the students in many developing countries around the world cannot have access to such equipment. As such, in this research, we are presenting cheap and easy preparation methods, with some details, for even equipment calibration and some tricks to attain a reliable composite structure for educational purposes. Moreover, the software and solvers used in this study are freely provided by the supplier for educational purposes. This study examined two methods for producing carbon and glass/polyester composite plates and discussed which one was best based on mechanical properties for different volume fractions, random stacking sequences, and ply angles (using OCTAVE's random estimation program). It also determined the three natural frequencies experimentally and with the aid of ANSYS. Less than 6% separated the experimentally determined natural frequencies from the calculated results.

An 8-months old male American Staffordshire terrier was referred for a no weightbearing lameness of the right pelvic limb, hyperthermia, lethargy and inappetence caused by hematogenous osteomyelitis. Orthopedic, radiographic and tomographic examinations revealed a bone sequestrum of 4 x 1.4 cm and active periosteal reaction of the caudo-lateral cortical in the metaphysis and the distal third of the right femoral diaphysis, medullary osteolysis and interruption of the cranio-medial cortical profile, with involvement of the femoral trochlea leading to a secondary medial patella luxation. Once skeletally mature, after 4 months from surgical debridement and aggressive antibiotic therapy against Klebsiella oxytoca revealed by bacteriological exam, the patient underwent prosthetic surgery for the application of a custom-made patellar groove replacement (PGR) to fill the bone defect and restore the femoral trochlea surface. Despite the serious injury that afflicted the right pelvic limb, the surgery had satisfactory outcomes until the last 18-months postoperative follow up.

Rice is consumed as a staple food by majority of the people in the world and failure in rice crop, due to any reason, poses a severe threat of starvation. Rice blast, caused by a fungus blast has been ranked among the most important plant diseases. It is by far the most threatening disease of ric crop and it is found wherever rice is grown. All of the rice blast disease management strategies that have been employed have limited success and rice blast has never been eliminated from a region in which rice is grown. Hence there is need to look for the best remedy in terms of effectiveness and organic nature of the method etc. This study was aimed to determine the plant growth promoting and biopesticidal effects of bioactive components present in a mixture of Piper caninum and Piper betle var. Nigra leaf extracts. . The extracts were applied in the field to determine their inhibition effects against blast disease, growth and yield improvement.. Extract of both the plants promoted plant growth and exhibited antifungal activity against rice blast fungus, Pyricularia oryzae. However the synergistic effect of the mixture of the two extracts exhibited greater effects than an effect of a single extract. . All treatments reduced the intensity of blast disease on week 15 with disease intensity by 7.90%. The extracts could increase plant height, the numbers of tillers, number of leaves, number of grains per panicle number of heads per panicle, and the full-grain weight hill.. The highest potential yield (t/ha) was observed in the 2% extract treatment, and all treatment results significantly differed from that of the control. The potential grain yield was 3.23 t/ha in the control, while that in the treatment ranged from 3.81 t/ha to 5.61 t/ha. The high grain yield observed with the treatment was caused by the low intensity of blast disease.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

The utilisation of the industrial residual products to develop new value-added materials and to reduce footprint is one of the critical challenges of science and industry. Development of the new multifunctional and bio-based composites materials is an excellent opportunity for the effective utilisation of industrial residual products. Keeping the different issues in mind, in this work, we describe the manufacturing and characterisation of the three-phases bio-based composites. The key components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash, i.e. the cenosphere (CS). The three-phase composite prepared in the form of a block were investigated for their mechanical properties and density. The three-phase composite was prepared in the form a) of a block were investigated for their mechanical properties, and density and b) a form of granules for determination of the water and oil products sorption were investigated. We have also investigated the dependence of the properties on the DCR and CS fraction. It has been found, that maximum compression strength (in block form) observed for composition without CS and DCR addition was- 79.3 MPa, while the second-highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt%, the compression strength is in the range from 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.

The main purpose of this work is to contribute to understanding the mechanism of oxidation of the polymeric components of common disposable masks used during the COVID-19 pandemic to offer the chemical basis to predict their long-term behaviour under typical environmental conditions. Artificial ageing of representative mask layers under isothermal conditions (110℃) or accelerated photoageing showed that all the PP-made components underwent a fast oxidation process, following the typical hydrocarbon oxidation mechanism. In particular, yellowing and the melting temperature drop are early indicators of their diffusion-limited oxidation. Morphology changes also induced a loss of mechanical properties, observable as embrittlement of the fabric fibres. Results were validated through preliminary outdoor ageing of masks, which allows us to predict they will suffer fast and extensive oxidation only in the case of contemporary exposure to sunlight and relatively high environmental temperature, leading to their extensive breakdown in the form of microfiber fragments, i.e., microplastics.

Social and academic integration variables have shown to be relevant for the understanding of university dropout. However, there is less evidence regarding the influence of these variables on dropout intention, as well as predictive models that explain their relationships. Improvements in this topic become relevant considering that dropout intention stands as a useful measure to anticipate and intervene on this phenomenon. The objective of the present study was to evaluate a predictive model for the university dropout intention that considers the relationships between social and academic variables, during the first university semester of 2020. The research was carried out using a cross-sectional associative-predictive design, with a convenience sampling (n=711) due the restrictions of pandemic period. The results showed a good fit of the proposed hypothetical model that explains 38.7% of dropout intention. Both social support and perceived social isolation predicted the sense of belonging, and through it, engagement. Previous academic performance predicted early academic performance, and through it, engagement. The set of variables predicted the intention to quit, through engagement. These results are a contribution both to the understanding of the phenomenon and to guide potential interventions in the early stages of the university experience.

The impact of ponds on basins has recently started to receive its well–deserved scientific attention. In this study, pond–induced impacts on soil erosion and sediment transport were investigated at the scale of the French Claise basin. In order to determine erosion and sediment transport patterns under current conditions, the CORINE erosion and SWAT models were used. The impact of ponds on the studied processes was revealed by means of land cover change scenarios, using ponded versus pondless inputs. Results show that under current conditions (pond presence), 12.48% of the basin corresponds to no–erosion risk zones (attributed to the dense pond network), while 65.66% corresponds to low–erosion risk, 21.68% to moderate–erosion risk and only 0.18% to high–erosion risk zones. The SWAT model revealed that ponded sub–basins correspond to low sediment yields areas, in contrast to the pondless sub–basins, which yield appreciably higher erosion rates. Under the alternative scenario, erosion risks shifted to 1.12%, 0.52%, 76.8% and 21.56% for no, low, moderate and high–erosion risks, respectively, while the sediment transport pattern of the Claise completely shifted to higher sediment yield zones. This approach solidifies ponds as powerful man–induced modifications to hydro/sedimentary processes.

Pounded yam eaten with any type of soup is a delicacy eaten by Nigerians. It is manually prepared by pounding yam, cocoyam or combination with mortar and pestle. Preparation takes 30-45 mins. Researches on the improvements have taken place to reduce the heavy burden on the pounded yam preparation. One of the efforts made is the fabrication of pounding machine from the Department of Engineering, Federal College of Agriculture, Akure, Nigeria. The aim of this study is to carry out the organoleptic analysis of pounded yam produced from the fabricated machine. A ten-man panelist was used to determine the organoleptic analysis of the pounded yam in terms of the appearance, taste, colour, odour and texture. The panelists were scored with a class of quality grading: 22.6-25.0 (excellent), 20.2-22.5 (good), 18.2-20.1 (satisfactory), 16.2-18.1 (less satisfactory), and <15.2 (unsatisfactory). Also, sensory attributes were scored as 1= unsatisfactory, 2= less satisfactory, 3= satisfactory, 4=good, and 5= excellent. The results were statistically analysed. From the results it was found that the mean results of appearance, colour, odour, taste, and texture were 4.55, 4.43, 4.15, 4.32, and 4.08 respectively. Coefficients of variation (%) were 16.89, 17.80, 21.65, 15.67, and 24.40. The Skewness of the parameters was in negative, while only odour has its Kurtosis in negative form (-0.37). All the panelists rated the appearance (19-24%) of all the samples high above all other parameters. The Pearson Coefficient of Correlation and Principal Component Analysis showed elements of relationships between the parameters. In conclusion, the machine pounded yam was scored above satisfactory, which means the fabricated machine was efficient.

Abstract: This work is presenting a water level control and monitoring system in a tank, by using the development boards Arduino Uno, NodeMCU ESP8266 and the ultrasonic sensor HC-SR04. The water tank is supplied through a pump controlled by the development board Arduino Uno by means of a relay. The author has issued a control algorithm for controlling the water level and a program in the development environment Arduino IDE that has been implemented and validated on the experimental stand. For monitoring the development board NodeMCU ESP8266 has been used that takes the information from the ultrasonic sensor HC-SR04 and sends it through Wi-Fi to the platform ThingSpeak. Based on the experimental results it has been found out that the water level control system in the tank provides the performances imposed through the designing stage, and the pump running has been automatically stopped when the limit, settled through the program for the water maximum level in the tank, has been reached. The measured value of the water level is shown on the LCD 1602 display. In the water circuit of the home consumers or irrigation systems supplied from the tank a pump controlled by means of a mobile phone has been installed. In order to implement this control system, the author has issued a program for another development board Arduino Uno, whilst for the mobile phone he used the application Arduino Bluetooth Control. The advantage of this water level control and monitoring system in the tank is given by the very low costs in comparison to the cost of an industrial type control system.

The total, soluble and insoluble oxalate contents of fresh and wok-fried fat hen (Chenopodium album) leaves were extracted and measured using HPLC chromatography. The total oxalate content of the raw leaves was 1112.4 mg/100 g dry matter (DM), and the levels were significantly reduced by boiling (682.8 mg/100 g DM) or cooking the leaves in a wok (883.6 mg/100 g DM). The percentages of soluble oxalate contents in the total oxalates of the raw and boiled leaves were similar (mean 75%), while the proportion of soluble oxalate content in the wok-fried leaves were reduced to 53.4% of the total, giving a significant increase in the insoluble oxalate content of the wok-fried leaves. The percentage of insoluble calcium in the total calcium was significantly reduced (P < 0.05) when the leaves were boiled but the insoluble oxalate content significantly increased (67.2%) in the wok-fried leaves when compared to the content of the original raw leaves. Processing the cooked leaves into pesto or extracting the juice gave final products that contained significantly reduced total and soluble oxalate contents. The addition of calcium chloride to the juice made a very small reduction in the soluble oxalate content in the juice.

Chitooligosaccharides (COS) are -1,4-linked homo-oligosaccharides of N-acetylglucosamine (GlcNAc) or glucosamine (GlcN), and also include hetero-oligosaccharides composed of GlcNAc and GlcN. These sugars are of practical importance because of their various biological activities, such as anti-microbial, anti-inflammatory, anti-oxidant and anti-tumor activities, as well as triggering the innate immunity in plants. The reported data on bioactivities of COS used to contain some uncertainties or contradictions, because the experiments were conducted with poorly characterized COS mixtures. Recently, COS have been satisfactorily characterized with respect to their structures, especially the degree of polymerization (DP) and degree of N-acetylation (DA); thus, the structure-bioactivity relationship of COS has become more unambiguous. To date, various green-chemical strategies involving enzymatic synthesis of COS with designed sequences and desired biological activities have been developed. The enzymatic strategies could involve transglycosylation or glycosynthase reactions using reducing end-activated sugars as the donor substrates and chitinase/chitosanase and their mutants as the biocatalysts. Site-specific chitin deacetylases were also proposed to be applicable for this purpose. Furthermore, to improve the yields of the COS products, metabolic engineering techniques could be applied. The above-mentioned approaches will provide the opportunity to produce tailor-made COS, leading to the enhanced utilization of chitin biomass.

Developing advanced carbon materials by utilizing biomass waste has attracted much attention. Herein, a N-doped carbon material (RSM-0.33-550) was prepared by directly pyrolyzing reed straw and melamine. The as-prepared RSM-0.33-550 possessed a N content of 6.02% and a specific surface area of 547.1 m2 g-1. As the anode for supercapacitors (SCs), in 6 M KOH, such RSM-0.33-550 exhibited a capacitance of 202.8 F g-1 at a current density of 1 A g-1. At a high current density of 20 A g-1, it still remained a capacitance of 158 F g-1. Notably, it delivered an excellent stability with capacity retention of 96.3% at 20 A g-1 after 5000 cycles. This work not only offer a new electrode material for SCs, but also gives a new insight for rationally utilizing the biomass waste for energy storage.

Municipal solid waste management is a growing worldwide challenge. Landfill mining is a promising technique to reduce MSW landfills. In the present study, arbitrary embankments made of different MSW fractions are analyzed to find the safety factor of their slopes. Properties of Municipal solid waste fines (MSWF), Shredded MSW, MSW Incineration Ash, and MSW having particles less than 35 mm are used in the analysis. For doing the same, finite element-based application 'Plaxis-2D' is used. The safety of slopes is assessed while the water table is inserted, and a uniform load is applied to the embankment to establish how well they will perform in critical situations. It was found that the slope made of shredded MSW is most safe due to its low density and high friction angle, while the least safe slope is made of MSW having less than 35 mm fractions.

This study provides a contribution to the research field of 3D printed earthen buildings, focusing, for the first time, on the load-bearing capacity of these structures. The study involves the entire production and testing process of the earthen elements, from design, to the preparation of the mixture and the 3D printing, up to the uniaxial compression test on a wall segment. The results indicate that 3D printed earthen elements have a compressive strength of 2.32 MPa, comparable to that of rammed earth structures. The experimental data also made it possible to draw conclusions on the action of the infill, which seems to have the function of stopping the propagation of cracks. This has a positive effect on the overall behavior of 3D printed earthen elements, since it avoids the onset of dilative behavior in the final stages of the load test and maintains ultimate load values higher than 50% of the maximum load.

The utilisation of the industrial residual products to create new value-added materials and to reduce footprint is a modern challenge of science and industry. Development of the new multifunctional and bio-based composites is an excellent opportunity for complex utilisation of industrial residual products. The study describes the preparation and characterisation of the three-phases bio-based composites. The main components are bio-based binder made of peat, devulcanised crumb rubber (DCR) from used tires and part of the fly ash the cenosphere (CS). Three-phase composite prepared in the form of a block for investigation of the mechanical properties and density and a form of granules for determination of the water and oil products sorption was investigated. This work investigated the dependence of the properties on the main component DCR and CS fraction. Is found, that maximum compression strength (in block form) observed for composition without CS and DCR addition - 79.3 MPa, the second highest value of compression strength is 11.2 MPa for composition with 27.3 wt% of CS. For compositions with bio binder content from 17.4 to 55.8 wt% and with DCR contents in range from 11.0 to 62.0 wt% compression strength is in range 1.1 to 2.0 MPa. Liquid sorption analysis (water and diesel) showed that the maximum saturation of liquids in both cases is set after 35 minutes and ranges from 1.05 to 1.4 g·g -1 for water and 0.77 to 1.25 g·g-1 for diesel. It was noted that 90% of the maximum saturation with diesel fuel comes after 10 minutes and for water after 35 minutes.

In order to assess the human exposure risks from the release of contaminants from water pipes made of polyvinyl chloride (PVC), experiments were carried out by subjecting the PVC pipe material to burning and leaching conditions followed by analysis of the emission and leachate samples. The emissions of burning pipes were analyzed by both infrared spectrometry and gas chromatography-mass spectrometry (GC-MS). The emission results indicate the presence of chlorinated components including chlorine dioxide, methyl chloride, methylene chloride, allyl chloride, vinyl chloride, ethyl chloride, 1-chlorobutane, tetrachloroethylene, chlorobenzene, and hydrogen chloride were detected in the emissions of burning PVC pipes. Furthermore, the concentrations of benzene, 1,3-butadiene, methyl methacrylate, carbon monoxide, acrolein, and formaldehyde were found at levels capable of affecting human health adversely. The analysis of PVC pipe leachates using GC-MS shows that there are 40-60 tentatively identified compounds, mostly long-chain hydrocarbons such as tetradecane, hexadecane, octadecane, and docosane, were released when the burned PVC materials were soaked in deionized water for one week. Quantitative analysis shows that 2-butoxyethanol, 2-ethyl-1-hexanol, and diethyl phthalate were found in the burned PVC polymer at the average levels of 2.7, 14.0, and 3.1 micrograms per gram (g/g) of pipe material. This study has significant implications for understanding the benzene contamination of drinking water in the aftermath of wildfires that burned polymer pipes in California.

This paper compares two types of microfluidic sensors that are designed for operation in ISM bands at microwave frequencies of 2.45 GHz and 5.8 GHz. In the case of the first sensor, the principle of operation is based on the resonance phenomenon in a microwave circuit filled with a test sample. The second sensor is based on the interferometric principle and makes use of the superposition of two coherent microwave signals, where only one of them goes through a test sample. Both sensors are monolithic structures fabricated using low temperature co-fired ceramics (LTCC). The LTCC-based microwave-microfluidic sensor properties are examined and compared by measuring their responses for various concentrations of two types of test fluids: one is a mixture of water/ethanol, and the other is dopamine dissolved in a buffer solution. The experiments show a linear response for the LTCC-based microwave-microfluidic sensors as a function of the concentration of the components in both test fluids.

Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.

In order to reduce the environmental damage caused by coal waste landfills, it is necessary to look for rational ways of their management. One of the methods of their development may be the creation of soil-like substrates. The aim of the study was to assess the properties of soil-like substrates from coal mining waste with a varied share of sewage sludge and waste mineral wool. The evaluation of the properties of the substrates was carried out in a pot experiment. The properties of the substrates and their yield potential were determined. Coal mining waste as a substrate, compared to anthropogenic soil, was characterized by: significantly higher sorption capacity, content of alkaline cations and pH, significantly higher content of organic carbon, nitrogen and assimilable forms of K and Mg, and lower content of assimilable P. The substrates enriched with sewage sludge showed: significant increase in the content of organic carbon, nitrogen and assimilable forms of P and Mg, optimization of sorption properties. Extending the composition of substrates with mineral wool resulted in further improvement of their properties. Yields of plants grown on coal mining waste were significantly lower than on anthropogenic soil. Substrates with sewage sludge and mineral wool had a significantly higher yield potential.

We propose a geographical time-space model extending time-space relief cartography introduced by Mathis and L’Hostis [,,,]. The novelty of the model resides in the use of cones to describe the terrestrial surface instead of graph faces, and in the use of curves instead of broken segments for edges. The approach lies a the intersection of two domains involving graphic representation: cartography, and three dimensional computer graphics. We implement the model on the Chinese space. The Chinese geographical time-space of the reference year 2006 is produced by the combination and the confrontation of the fast air transport system and of the 7.5 times slower road transport system. Slower, short range flights are represented as curved lines above the earth surface with longer length than the geodesic, in order to account for a slower speed. The very steep slope of cones expresses the relative difficulty of crossing terrestrial time-space, as well as the comparably extreme efficiency of long-range flights for moving between cities. Finally, the whole image proposes a coherent representation of the geographical time-space where fast city to city transport is combined with slow terrestrial systems that allow to reach any location.

The human-centric approach is a leading trend for future production processes, and collaborative roboticists are key to its realization. This article addresses the challenge of designing a new cus-tom-made non-conventional machine or robot involving toolpath control (interpolated axes) with collaborative functionalities but by using “general-purpose standard" safety and motion control technologies. This is done on a non-conventional Cable-Driven Parallel Robot (CDPR). Safety is assured by safe commands to individual axes, known as Safe Motion Monitoring Functionalities, which limits the axes speed in the event of human intrusion. At the same time, the robot's Motion Controller applies an override to the toolpath speed to accommodate the robot's path speed to the axis’s limitations. The implementation of a new Pre-Warning Zone, prevent unnecessary stops due to the approach of the human operator. The article also details a real experiment that validates the effectiveness of the proposed strategy.

Nanoprecipitation by liquid anti-solvent precipitation is one of the most versatile methods to produce pure drug nanoparticles (PDNPs) owing to the ability to optimize the properties of the product. Nevertheless, nanoprecipitation shows broad particle size distribution and low physical stability, leading to high batch-to-batch variability and challenging the bench-to-bedside translation. Microfluidics has emerged as a powerful tool to produce PDNPs in a simple, reproducible, and cost-effective manner with excellent control over NP size. In this work, we designed and fabricated T- and Y-shaped Si-made microfluidics device and used it to produce pure NPs of three kinase inhibitors of different lipophilicity and water-solubility, namely imatinib, dasatinib and tofacitinib, without the use of colloidal stabilizers. PDNPs display sizes in the 90-350 nm range (dynamic light scattering) and a rounded shape (high-resolution scanning electron microscopy). Analysis by X-rays diffraction and differential scanning calorimetry confirmed that this method results in highly amorphous NPs. In addition, we show that the flow rate of solvent, the anti-solvent, and the channel geometry of the device play a key role in the size of the generated NPs.

We propose that the short−term memory (STM), when processing a sentence, uses two uncorrelated processing units in series. The clues for conjecturing this model emerge from studying many novels of the Italian and English Literatures. This simple model, referring to the surface of language, seems to describe mathematically the input-output characteristics of a complex mental process involved in a reading/writing a sentence. We show that there are no significant mathematical/statistical differences between the two literary corpora by considering deep-language variables and linguistic communication channels, therefore, the surface mathematical structure of alphabetical languages is very deeply rooted in human mind, independently of the language used. The first processing unit is linked to the number of words between two contiguous interpunctions, variable Ip, approximately ranging in Miller’s 7±2 range; the second unit is linked to the number of Ip’s contained in a sentence, variable MF, ranging approximately from 1 to 6. The overall capacity required to process fully of a sentence ranges from 8.3 to 61.23 words, values that can be converted into time by assuming a reading speed, giving the range 2.64~19.54 seconds for fast-reading and 5.3~30.1 seconds for average reader. Since a sentence conveys meaning, the surface features we have found might be the starting point to arrive at an Information Theory that includes meaning.

The article describes machine learning using artificial neural networks (ANN) to develop the parameters of the friction stir welding (FSW) process for three types of aluminum joints (EN AW 7075). A total of 608 experimental data were used to build the ANN. Two types of networks were built: the first one was used to classify good/bad connections with the MLP 7-19-2 topology, the second one was used to regress the tensile load-bearing capacity with the MLP 7-19-1 topology. Selected parameters of the FSW process were used as input data for ANN training: rotational speed, welding speed, joint and tool geometry. Based on a case study, the quality of the FSW joint was assessed in terms of microstructure and mechanical properties. The usefulness of both trained neural networks has been demonstrated. For the regression network, the quality of the validation set was approximately 93.6%. In the case of confusion matrix for the test set, errors never exceeded 6%. Only 184 epochs were needed to train the regression network. The quality of the validation set was approximately 87.1%. On their basis, predictive maps were developed and presented in the work allowing for the selection of optimal parameters of the FSW process for three types of joints.

This paper presents a theoretical evaluation of the prices of mixed briquettes produced from co-conut shells (CCS), banana peels (BNP), rattan waste (RWT), and sugarcane bagasse (SGC), and, on the other hand, an analysis of the economic viability of their use as a replacement for conventional household fuels (Liquefied Petroleum Gas, fuelwood, and wood charcoal) in house-holds in Cameroon. The investigation was carried out using the Life Cycle Cost method on a typical household over a ten-year period with annual cooking energy requirements of 950 kWhth. The SGC-CCS and SGC-RWT mixed briquettes with a ratio higher than 7.75% and 11.1%, respectively, have prices lower than 0.063 €/kWhth. The Present Value of the Net Benefit is posi-tive for the use of SGC-CCS and SGC-RWT mixed briquettes. The results show that by making the right mixes of residues, it is possible to obtain biomass briquettes that are less expensive than conventional fuels.

Mineral wool made from basalt fibers is frequently used as an insulating material in construction systems. In this study, both unused mineral wool, and wool obtained from the softened roofing area, were comprehensively analyzed in a laboratory using different characterization techniques. Firstly, the amount of initial water content and compressive strength at 10% deformation were determined. Secondly, microstructure and surface chemical composition were analysed by Scanning electron microscopy (SEM) equipped with energy dispersive x-ray spectroscopy (EDX). To study heterogeneities near the fiber surface and to examine cross-sectional composition, a Scanning transmission electron microscope (STEM) was used. Finally, to verify possible reasons for resin degradation, Thermogravimetry analysis and differential scanning colometry (TGA-DSC) were simultaneously carried out. The results show that natural aging under high humidity and thermal fluctuations greatly affects the surface morphology and chemical composition of fibrous composite. Phenol-formaldehyde and other hydrophobic compounds that protect fibers against moisture and give compressive resistance were found to be degraded.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

This study is focused on the mechanical properties of WC-Co composites obtained via Selective Laser Sintering using PA12 as a binder. The as-printed samples were thermally debonded, and sintered, first in vacuum, and then sinter-HIPed at 1400oC, using 50 bar Ar, which has led to relative densities up to 66 %. Optical metallographic images show a microstructure consisting of WC, with an average grain size in the range of 1.4 – 2.0 µm, with isolated large grains, in a well-distributed Co matrix. The shrinkage of the samples was 43 %, with no significant shape distortion. The printing direction of the samples has a great impact on the transversal rupture strength (TRS). Nevertheless, the bending strength was low, with a measured maximum of 612 MPa. SEM images of the fracture surface of TRS samples show the presence of defects that constitute the cause of the low measured values. The hardness values position the obtained composites in the range of medium coarse classical cemented carbides. The results were also related to the amount of free Co after sintering, close to the initial one, as assessed by magnetic measurements, indicating a low degree of interaction with PA12 decomposition products.

The use of acoustic and magnetic methods of non-destructive testing to detect zones of stable localization of deformation in order to assess and predict the performance of long-term equipment is of scientific and practical interest at present. A structural-mechanical criterion has been developed, that reflects the revealed relationships between the structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests in the metal of long-term equipment made of structural 0.2 С steel and heat-resistant 0,12C-1Cr-1Mo-1V steel. The values of the structural-mechanical criteria Ks.-m for structural 0.2 С steel and for heat-resistant 0,12C-1Cr-1Mo-1V steel, corresponding to the moment of stable localization of deformation, are established. At the same time, it is recommended to replace the checked equipment nodes due to the exhaustion of the resource. The proposed and justified approach to assessing and predicting the performance and residual life of long-term power equipment, based on the identified relationships between the structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests and the calculation of the structural-mechanical criterion, was applied at a number of power plants in the Kemerovo region – Kuzbass. A methodology has been developed for evaluating the residual life, based on the identification and use of relationships between structural and substructural states, internal stress fields and stable localization of deformations with the characteristics of non-destructive tests and the calculation of a structural-mechanical criterion.

This study aimed to investigate the diagnostic potential of circulating microRNAs (miRNAs) for detecting early myocardial fibrosis development in HFpEF patients. This observational study used a case-control research design. Peripheral blood samples were isolated from 25 HFpEF patients and 25 normal patients. They were measured for NTproBNP levels using ELISA, as well as MicroRNA-1, 21, and 29 levels using RT-PCR. All patients also underwent echocardiography for global longitudinal strain (GLS) to measure the myocardial fibrosis progression. Data were analyzed using SPSS 25.0. HFpEF patients had significantly higher GLS compared to the normal patients (-13±2.4% vs -19±3.2%; p &lt; 0.05), suggesting HFpEF patients tended to have myocardial fibrosis. HFpEF patients also had significantly higher microRNA-1 and microRNA-21 compared to the normal patients (p &lt; 0.05), but they had lower microRNA-1 (p &lt; 0.05). There was a positive correlation between microRNA-1 (r = 0.753; p &lt; 0.05) and microRNA-21 (r = 0.675; p &lt; 0.05) and an inverse correlation with microRNA-29 (r = -0.653; p &lt; 0.05) based on the GLS findings. By using a GLS cutoff of -15% for myocardial fibrosis, microRNA-1, microRNA-21, and microRNA-29 were found to be able to predict myocardial fibrosis based on GLS with a specificity of 78% and sensitivity of 75%. Increasing microRNA-1 and microRNA-21 followed by decreasing microRNA-29 in HFpEF patients suggest early myocardial fibrosis.

The effect of casein savinase hydrolysate (CSH) usage on frozen dough (1%, 1.5% and 2%, g/100 g flour) was investigated in terms of rheological, thermal, structural characteristics of wheat doughs and the textural and color properties of corresponding breads. Rheological measurement showed that CSH addition into dough led to a reduction of Gʹ and Gʹʹ values, but a similar trend wasn’t observed in frozen dough samples. The increase of protein band intensity was observed for control dough (CD) after frozen storage (-30 °C, 28 days) while there was no increases in band intensities of the doughs with CSH. The freezable water content of unfrozen doughs was decreased gradually with addition of CSH depended on concentration level. Frozen storage caused a notable reduction in α-helices structure of CD sample (p&lt;0.05) while no significant variation was observed for the doughs containing CSH (p&gt;0.05). Lowest specific volume reduction and hardness increment were observed for the breads containing 1.5% and 2% CSH. Frozen storage caused a significant reduction on b* value of bread crust (p&lt;0.05) while no significant effect was observed for L* and a* value during frozen storage (p &gt; 0.05). Overall, CSH incorporation into frozen dough can be an alternative that could reduce the quality deteriorations of frozen bread.

The electron Transport layer (ETL) plays a crucial role in solar cell technology, particularly in perovskite solar cells (PSCs), where nanostructured TiO2 films have been investigated as superior ETL’s compared to compact TiO2. In this study we explore the nanocolumnal growth of TiO2 in the anatase phase, for bilayer thin films by magnetron sputtering (MS) technique and glancing angle deposition (GLAD). By optimizing the growth parameters, we achieved the formation of TiO2 nanocolumns with a cross-sectional diameter ranging from 50 to 75 nm. The average thickness of the films exceeded 12.71 ± 0.5µm , while the filaments exhibited an inclination angle close to 70◦ , corresponding to the deposition angle. Furthermore, we observed a correlation between the quality of the initial layer and enhanced growth of the TiO2 nanocolumns.

Laser Direct Writing (LDW), also known as 3D multi-photon laser lithography of resins, is a promising technique for fabricating complex free-form elements, including micro-optical functional components. Regular organic or hybrid (organic-inorganic) resins are often used, with latter exhibiting better optical characteristics, as well as having the option to be heat-treated into inorganic glass-like structures, particularly useful for resilient micro-optics. While this work is a continuation of SZ2080™ calcination development , the Laser-Induced Damage Threshold (LIDT) of such sol-gel-derived glass micro-structures, particularly those that undergo heat treatment, has not been well-characterized. In this pilot study, we investigated the LIDT using the Series-on-One (S-on-1) protocol of functional micro-lenses produced via LDW and subsequently calcinated. Our results demonstrate that the LIDT can be significantly increased, even multiple times, by this approach, thus enhancing the resilience and usefulness of these free-form micro-optics. This work represents the first investigation in terms of LIDT into the impact of calcination on LDW produced sol-gel-derived glass micro-structures, and provides important insights for the development of robust micro-optical devices.

In open, sustainable policymaking, we are expecting to develop the valuable results that will bring us closer to a fairer and more balanced society. One way to involve the public in these processes is to engage them in online e-participation projects. Despite the hopes, empirical analyses show that many e-participation initiatives have failed to deliver expected benefits. Revealing what actually works in examined projects and what requires improvement would allow for better policy planning in the future. In this article, I made an attempt to identify and assess the cognitive processes enabling emergence of collective intelligence (CI) in a singular e-participation project. For this reason, I worked out and tested an evaluation technique, combining the MILCS framework for group cognition and the results of empirical research on CI. A case study method based on semi-structured interviews was selected to evaluate a sample participatory budgeting initiative, Civic Budget of the City of Kraków. Results reveal that most cognitive processes are working satisfactorily, but the real problem is using collective memory, which works only to a very limited extent. A guideline for future policymakers should be to develop a shared memory system, to which all community members should have access.

Following the general aim of recapitulating the native mechanical properties of tissues and organs in vitro, the field of materials science and engineering has benefited from recent progress in developing compliant substrates with similar physical and chemical properties. In particular, in the field of mechanobiology, soft hydrogels can now reproduce the precise range of stiffnesses of healthy and pathological tissues to study the mechanisms behind cell response to mechanics. However, it was shown that biological tissues are not only elastic but also relax at different timescales. Cells can indeed perceive and actually need this dissipation because it is a critical signal integrated with other signals to define adhesion, spreading and even more complicated functions. The mechanical definition of hydrogels used in mechanobiology is however commonly limited to the elastic stiffness (Young’s modulus) and this value is known to depend greatly on the measurement conditions that are rarely reported. Here, we report that a simple relaxation test performed under well defined conditions can provide all the necessary information to characterize soft materials mechanically, by fitting the dissipation behavior with a generalized Maxwell model (GMM). The method was validated using soft polyacrylamide hydrogels and proved to be very useful to unveil precise mechanical properties of gels that cells can sense and offer a set of characteristic values that can be compared with what is typically reported from microindentation tests.

Dynamic thermogravimetric (TG) analysis under nitrogen environment was used to understand the thermal decomposition process of 3D printing filaments made of wood-filled polylactic acid (PLA)/starch blend. The characteristic temperatures and apparent activation energy (AAE) of the filaments with various starch contents were calculated with well-known kinetic models by Friedman, Flynn-Wall-Ozawa, Coats-Redfern and Kissinger. With the increased starch content in the filament, the onset thermal decomposition temperatures of the filaments decreased gradually from 272.4 to 155.1°C. The thermal degradation degree became smaller, and the transitional temperature interval became larger with increased starch proportion. The AAE values of the three types of filaments with different starch ratios varied between 97 kJ/mol and 114 kJ/mol, depending on material composition and method of calculation. The improved understanding of thermal decomposition behavior of PLA-starch-wood composites can help develop more biodegradable PLA/starch-based filaments for 3D printing.

In this case study, an active runway of a civilian airport in Zonguldak, Turkey, is used to assess the suitability of spaceborne digital elevation models (DEMs) to model an anthropogenic structure. The tested DEMs include the ASTER, the AW3D30 m, the SRTM-1”, the SRTM-3”, the SRTM-X, the TanDEM-3”, and the WorldDEMTM. A photogrammetric high accuracy DEM was also available for the tests. As a reference dataset, a line leveling survey of the runway using a Leica Sprinter 150/150M instrument was performed. The selection of a runway as a testbed for this type of investigation is justified by its unique characteristics, including its flat surface, homogenous surface material, and availability for a ground survey. These characteristics are significant because DEMs over similar structures are free from environment- and target-induced error sources. The most accurate DEM is the WorldDEMTM followed by the SRTM-3” and TanDEM-3”, with vertical errors (LE90) equal to 1.291 m, 1.542 m, and 1.56 m, respectively. This investigation uses a method for identifying the vertical errors in DEMs that is known as the runway method.

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

Among the leading immersive technologies, Augmented Reality is one of the most promising and empowering to support designers in production environments. This research investigates the application of mobile augmented reality, based on the Web, as a mediation tool focused on cognitive activities of reading and understanding of Technical Drawings in the production and assembly for Tailor Made projects of the scenographic industry. In this context, the research presents a method to use the WebAR to improve the reading of technical drawings, seeking efficiency on the visualization of models and the exchange of information between professionals, involved in the processes of design, production and assembly of products, in the scope of scenography. This mediation tool was developed using Web AR platforms, compatible with native libraries (ARCore and ARKit) to ensure, first, compatibility with commonly used devices that workers or businesses can access, and secondly, to leverage hybrid tracking techniques that combine vision and sensors to improve the reliability of augmented reality viewing. The proposed solution adopts multiple tracking and navigation techniques in order to expand Space Skills components to provide greater exploratory freedom to users. The research process took place in the light of the Design Science Research Methodology and the DSR-Model, since it aimed to develop a solution to a practical problem, as well as to produce knowledge from this process. Field experiments were conducted in two real companies, with end users on their respective mobile devices, in order to evaluate usability and behavioral intent, through the Acceptance, Intent and Use of Technology questionnaires; and perceived mental workload, NASA-TLX. The experimental results show that the adoption of this tool reduces the cognitive load in the process of reading technical drawings and project´s understanding. In general, it´s usability and intent to use provide significant levels of satisfaction, being positively accepted by all participants involved in the study.

Influence of water concentration on the properties of fluorine-doped tin oxide (FTO) thin films was systematically studied in this work. Home made SISOM’s SPEED techniques and its chemical formulation was employed to grow the FTO on quartz substrate. Water concentration in the precursor solution was varied from 0, 0.5, 1.0 and 1.5 mol %. The structural, optical, and electrical properties of the films were studied under these deposition conditions. The results show that the properties of the films varied significantly with water concentration. Scanning electron microscopy (SEM) revealed FTO films whose grain size and uniformity increases significantly with increase in water concentration. The structure of the films was measured by X-ray diffraction (XRD) measurement. It shows polycrystalline films with (110), (101), (200), (211) and (220) orientation; the strength increases as water concentration increases. The optical transmission was determined by UV-Vis spectroscopy at 380–780 nm UV-VIS regions. The optical transmittance varies with water concentration with an average of 84%. The electrical property, measured by Hall Effect revealed n-type semiconductor. The films have the following properties: resistivity, 15 × 10^-4Ω cm; carrier concentration, 18.7 × 10¹⁹ cm^-3 and mobility of 21.86 cm² V^-1 s^-1. The average figure of merit, φ of the FTO film is 1.25. Optimum deposition condition was established after series of experiments and was found to be 1.5% water concentration at 460^oC substrate temperature. The FTO films deposited in this work could be a promising replacement to indium tin oxide (ITO) especially in dye-sensitized solar cells.

Scaffolds are widely used in tissue engineering because their manufacture is based on natural and synthetic polymers, which allows them to have properties such as biocompatibility and biodegradability, creating an ideal environment for cell growth on their surface. In this context, among the polymers studied in Tissue Engineering are Chitosan (CH) and Polyvinyl Alcohol (PVA). CH is a versatile polymer obtained from de-acetylation of chitin, which is used for its high biodegradability and biocompatibility, although its mechanical properties must be improved. It has been found that one of the ways to improve the mechanical properties of CH is to mix it with other synthetic polymers such as PVA. PVA is known for its biocompatibility, biodegradability, zero toxicity and ease of preparation due to its solubility in water and excellent mechanical properties, such as tensile strength and ease in the formation of films and barriers. In this study we evaluated the capacity of scaffolds made with CH and PVA in different concentrations (2: 1, 1: 1, 1: 2, respectively) as a possible application in bone regeneration. This was made through different characterization tests such as Infrared Spectroscopy, AFM, Swelling test and Porosity test, where we obtained information about its structural and physicochemical properties. Additionally, a cellular quality control was performed on the material through the MTT assay. The Fourier transform infrared spectroscopy (FTIR) study showed that there are strong intermolecular hydrogen bonds between the chitosan and polyvinyl alcohol molecules. The Swelling and Porosity tests showed favorable results, obtaining maximum values ​​of 5519% and 72.17% respectively. MTT tests determined that the prepared materials are not cytotoxic. These findings suggest that scaffolds possess properties suitable for use in Tissue Engineering.

SIRT6 is a NAD+ dependent enzyme and stress response protein that has sparked the curiosity of a plethora of researchers in different branches of the biomedical sciences. A unique member of the known Sirtuin family, SIRT6 has several different functions in several different molecular pathways related to DNA repair, glycolysis, gluconeogenesis, tumorigenesis, neurodegeneration, cardiac hypertrophic responses and so on. Only in recent times however did the potential usefulness of SIRT6 come to light as we learned more about its biochemical activity, regulation, biological roles and structure [1]. Even until very recently, SIRT6 was known more for chromatin signaling but being a nascent topic of study, more information has been ascertained and its potential involvement in major human diseases namely, diabetes, cancer, neurodegenerative diseases and heart disease has been demonstrated. It is pivotal to explore the mechanistic workings of SIRT6 since future research may hold the key to engendering strategies, involving SIRT6, that may have significant implications for human health and expand upon possible treatment options. In this review, we are primarily concerned with exploring the latest understanding of SIRT6 and how it can alter the course of several life-threatening diseases that cripple today’s society such as processes related to aging, cancer, neurodegenerative diseases, heart disease and diabetes. In addition, SIRT6 has shown to be involved in liver disease, inflammation and bone related issues but more emphasis is given to the former. Lastly, any recent promising pharmacological investigations and study of potential therapeutic targets are also delineated in this review.

Promoting sustainable consumer behavior is now an obligation under new European legislation, requiring Life Cycle Assessment (LCA) for accurate environmental impact evaluation. Portugal is a key textile producer, edge in competitiveness in sustainable textile production, driven by electricity-reduced carbon footprint and closed-loop manufacturing. Additionally, while simple spreadsheets can estimate a product's carbon footprint, openLCA software, combined with ecoinvent database, greatly enhances environmental footprint calculations by integrating diverse impact categories, otherwise difficult to estimate. In this study, openLCA is used to evaluate the environmental footprint of a white T-shirt made in Portugal, with 50% recycled cotton from post-industrial wastes combined with 50% organic cotton from Turkey, to assist the design of environmental key performance indicators (KPI). The RECIPE and EF method (adapted) are used to calculate the environmental impacts and allow aggregation in a single score. The KPI related to the global warming impact is validated using a spreadsheet calculator. We propose an “Envi-Score” based on an A to E classification for benchmarking and better communication with the buyers. E is set as the normalized environmental impact of the European benchmark for a mixture material T-shirt encompassing cradle-to-gate boundaries. The introduction of recycled cotton proves to be environmentally beneficial over organic and conventional cotton. Organic cotton proves to be beneficial in comparison with conventional cotton for most environmental categories, except to the ones affected by the lower production yield, for example Land Use. The hotspots for the main impact categories are identified and finally proposed a labelling scheme, to clearly inform about the environmental performance of the products and avoid greenwashing, with the “Envi-Score” rate, carbon footprint, land use and water depletion.

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals like magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For WE43 scaffolds, during the first days an increase of the smeared Young's modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the struts surfaces. In this study the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite element simulations are performed to study the influence of the substrate layer thickness and Young's modulus for single struts and for a new scaffold geometry with adapted polar f2cc,z unit cells. The finite element model is further validated by compression tests on AM scaffolds made from Zn1Mg. The results show, that even low thicknesses and Young's moduli of the substrate layer increases significantly the smeared Young's modulus under axial compression.

This study focuses on the design, development, and evaluation of an educational mobile robot, named Robot-T2, to be used in educational activities within a technical school. The primary objective was to create a versatile platform that allows students to explore programming, engineering, and science concepts in a practical and collaborative manner. The methodology included an iterative design and testing approach, incorporating feedback from students and teachers to continuously improve the robot's functionality. The tests covered autonomous navigation, line following, and object manipulation, using the OnBotJava programming software and the Control Hub as the main interface. The results demonstrated that Robot-T2 is highly efficient and adaptable in various educational contexts, showing remarkable precision in navigation and object manipulation. The design iterations significantly improved the robot's performance, enriching the educational experience and promoting active learning. In conclusion, educational robotics, represented by Robot-T2, has great potential to enhance the teaching and learning process in technical schools, fostering teamwork, problem-solving, and the integration of technology in the classroom. This project is expected to inspire future developments in educational robotics.

Laser metal deposition with wire (LMD-w) is a developing additive manufacturing (AM) technology that has a high deposition material rate and efficiency, and is suitable for fabrication of large aerospace components. However, control of material properties, geometry, and residual stresses is needed before LMD-w technology can be widely adopted for the construction of critical structural components. In this study, we investigated the effect of interlayer cooling time, clamp constraints, and tool path strategy on part distortion and residual stresses in large-scale laser additive manufactured Ti-6Al-4V components using finite element method (FEM). The simulations were validated with the temperature and the distortion measurements obtained from a real LMD-w process. We found that a shorter interlayer cooling time, full clamping constraints on the build plates, and a bidirectional tool path with 180⁰ rotation minimized part distortion and residual stresses and resulted in symmetric stress distribution.

Insufficient oral ridge tissue presents a challenge in the treatment of dental implants. One method to enhance alveolar crest dimensions is guided bone regeneration (GBR); however, existing membranes have certain limitations. To address this issue, we aimed to compare the effectiveness of a resorbable bilayer membrane composed of poly(l-lactic acid) and poly(-caprolactone) （PLACL）with that of a collagen membrane（COL） in a rat GBR model. The rat calvaria was used as an experimental model by placing a plastic cylinder. Forty male Fisher rats underwent surgery, and micro-computed tomography and histomorphometric analyses were performed to assess bone regeneration. The results showed that bone regeneration was similar across all the groups. However, after 24 weeks, the PLACL membrane demonstrated significant resilience, occasional partial degradation, and intermittent air bubble formation. This extended preservation of the barrier effect has great potential to facilitate optimal bone regeneration. In conclusion, this study shows that the PLACL membrane is a promising alternative to GBR. By providing a durable barrier and supporting bone regeneration over an extended period, this resorbable bilayer membrane may address the limitations of the current membranes. Further studies and clinical trials are warranted to validate the efficacy and safety of this drug in humans.

This review asks some hard questions about what the enigmatic graphoglyptid trace fossils are, documents some of their early fossil record from the Ediacaran-Cambrian transition and explores the idea that they may not have been fossils at all. Most researchers have considered the Graphoglyptida to have had a microbial-farming mode of life similar to that proposed for the fractal Ediacaran Rangeomorpha. This begs the question “What are the Graphoglyptida if not the Rangeomorpha persevering” and if so then “What if…?”. This provocative idea has at its roots some fundamental questions about how to distinguish burrows sensu-stricto from the external molds of endobenthic sediment displacive organisms.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

This study explores the elements that influence consumer vegetarian diet choices in parts of South Korean provinces. The study examines these explanatory variables: ethical-animal-welfare, health, environment, social issues , mood-emotion, and religious-beliefs with vegetarianism serving as the dependent variable. The Likert scale data from 264 respondents were analyzed using logistic regression analysis. Results show that health, ethical-animal-welfare ideals as well as environmental concerns emerge as significant variables influencing the decision to embrace a vegetarian diet. This shows that consumers (international students) in Korea are becoming more aware of and concerned about health, ethical and sustainable dietary choices. Secondly, health plays a crucial role in the vegetarian diet selection, indicating that health-conscious people are more inclined to choose a vegetarian lifestyle. Religious belief and mood have various degrees of influence on the vegetarian diet decision. The findings of this study have consequences for consumer behavior, marketing managers, and decision-makers. Businesses in the food industry, in particular, can gain from catering to the needs and tastes of consumers that prioritize ethical-animal welfare ideals, as well as those that value health and environmental sustainability. Creating and advertising vegetarian and vegan choices in local restaurants can effectively attract and serve this specific target demographic.

The development of analog rice, apart from being an effort to diversify food, also has the potential to be develop as functional food in fulfilling the nutrients needed by a community. Katuk leaf is known for its ability to accelerate breast milk production for lactating women which is inseparable from sterol as bioactive content. This study aimed to determine the best formulation of analog rice made from cassava flour, banana flour, Katuk leaf powder and soy lecithin that was sensory acceptable, in a shape resembling rice, and able to fulfill the nutritional needs of lactating women. Analog rice was produced using extruder machine before the physical and sensory properties analyses were carried out, followed by the chemical properties analysis. Formulation C (80% cassava flour, 20% banana flour, 3% Katuk leaf powder and 0.5% soy lecithin) was obtained as the best or most preferred formulation based on sensory analysis which the grain shaped oval round resembling original rice and had green-brownish color, fluffy texture, distinct aroma and taste derived from the raw material used. Therefore, this research is expected to support the development of analog rice for providing the main staple food for fulfilling the lactating women’s nutrition.

This paper attempts to compare two different approaches to solve the problem of accident rates prediction based on human factors for industrial workers. One of the methods has already been done using Fuzzy c-Means Clustering and proved to be working with decent results. The second method which will be covered in this paper is using Artificial Neural Networks. The primary goal of this work is to insure that ANN will work efficiently in such prediction problem. The second goal is to reveal the fact that which one of the two selected methodologies is better at defining the estimation of accident rates among people who work in different industrial fields. The purpose has been achieved when the outcome of the ANN was obtained and compared accordingly with the output of the research previously carried out with Fuzzy c-means clustering method. Comparing the outcomes of these two different methods gave an immense insight on which features are more important than others when it comes to laborers properties with completely different background such as varying levels of health, knowledge, experience, training and physical properties. At the end of the research, it becomes clear that accident rates estimation for laborers with properly trained Artificial Neural Network gives better results when it is compared with Fuzzy c-Means Clustering method. Standard deviation method was used to calculate the validity of ANN technique. The result was compared with Fuzzy c-mean clustering technique. Impressive improvement of 8.8% in the accident rate prediction was achieved using Tailored-Made-ANN.

One of the modern methods of improving operating characteristics of titanium and titanium-based alloys under conditions of friction and increased contact loads is the method of ion-plasma nitriding. The effect of nitriding of VT5 alloy (Al 4,5-6,7 %, V to 1,2 %, Mo to 0,8 % − analogue 3.7115) in the plasma of a glow discharge excited in a hollow cathode on its tribological characteristics in pairs with different materials in T-1 fuel and under dry friction conditions has been studied. For research and tribological tests, samples of VT5 alloy were nitrided in the plasma of a glow discharge excited in a hollow cathode at a temperature of 975 ± 15°C and a pressure of 58 ± 2 PA in a nitrogen-argon gas mixture with a nitrogen content of 78 %. Studies of samples of VT5 alloy after nitriding showed that the surface roughness Ra was in the range of 0.58-0.64, and the surface hardness HV5 was 525 ± 20 kgf/mm² at a base hardness of 325 ± 15 kgf/mm². Tribological tests were performed on a friction machine 2070 SMT-1 according to the scheme "cube - roller". Tests under conditions of friction with oil were performed at a load of 200 N. The sliding speed during the tests was 1.3 m/s, the test time was 75 sec. The test under dry friction conditions was carried out at a load of 100 N and a sliding speed of 0.785 m/s, the test time was 30 minutes. Low wear ability in relation to the nitrided titanium alloy VT5 (<2.4x10^-4 mm³/s), as well as friction coefficients at the level of 0.08 to 0.12 in the order of their growth had bronze VB-23NTS (Pd 18–22 %, Ni 3–4 %, Zn 3–4 %, Sb 3–4 %, P 0.15–0.3) r.O10C2N3, VB-24 (Sb 4.7–6, 2 %, P 0.4–0.9), steel 1.3505, cast iron GGG80, cemented steel 20Cr3MoWV.

Background: The aim of the present investigation was to evaluate the clinical success of horizontal ridge augmentation in the severely atrophic maxilla (Cawood and Howell class IV) using freeze-dried custom made bone harvested from cadaver donors tibial hemiplateau and to analyze the marginal bone level gain prior dental implants placement at 9 months after bone grafting and before prosthetic rehabilitation. Methods: A 52-year-old woman received custom made bone grafts. Patient underwent CT scans 2 weeks prior and 9 months after surgery for graft volume and density analysis. Results: The clinical and radiographic bone observations showed a very low rate of resorption after bone graft and implant placement. Conclusions: The custom-made allograft material was a highly effective modality for restoring the alveolar horizontal ridge, resulting in this way to reduce the need to obtain autogenous bone from a secondary site with predictable procedure. Further studies are needed to investigate its behavior at longer time points.

Semi-destructive and non-destructive techniques are not commonly used for masonry as they are complex and difficult to perform. This paper describes validation of the following methods: semi-destructive and non-destructive, ultrasonic technique for autoclaved aerated concrete (AAC). The research subject was the compressive strength of AAC test elements with declared various density classes of: 400, 500, 600 and 700 (kg/m3) and various moisture levels. Empirical data including the shape and size of specimens, were established from tests on 494 cylindrical and cuboid specimens, and standard cube specimens 100×100×100 mm using the general relationship for standard concrete (Neville’s curve). The effect of moisture on AAC was taken into account while determining the strength fBw for 127 standard specimens tested at different levels of water content (w = 100%, 67%, 33% 23% and 10%). Defined empirical relations can be used to correct the compressive strength of dry specimens. For 91 specimens 100×100×100 mm, the P-wave velocity cp was tested with the transmission method using using the ultrasonic pulse velocity method with exponential transducers. The curve (fBw – cp) for determining the compressive strength of AAC elements with any moisture level (fBw) was established.

Construction and demolition waste (CDW) represents 1/3 of the weight of all-waste produced. Increasing their recycling and reutilization with recycled aggregates (RA) means closing the life cycle of construction materials. Research has been carried out on artificial aggregates from the exclusive crushing of structural concrete waste in selective demolitions (CDWRConc). This study analyses the use of recycled concrete as graded aggregate (GARConc) and in cement soil (CSRConc). The material complies with the requirements as a road base, although due to the low values of resistance to fragmentation these materials are adequate for use in sensitive road systems and other places such as urban roads and car parks. The sensitive road systems are infrastructures in places of great natural wealth and low traffic intensity, with an annual average of heavy vehicle traffic (AADTh) below 50 vhp/d. As soluble salt contents have been detected, additional waterproofing or drainage measures must be adopted to prevent water infiltration into the layers made up of CDWRHorm. Finally, the high initial values of UCS allow the temporary passage of light vehicles over CSRConc after 3 days.

Synergistic effects between reactions, reagents and catalysts can lead to minor heats of reaction and occur as an inherent result of multi-component reactions (MCRs) and their extensions. They enable syntheses to be performed at a low energy level and the number of synthesis steps to be drastically reduced in comparison with ‘classical’ two-component reactions. The very high potential for variability, diversity and complexity of MCRs additionally generates an extremely diverse range of products, thus bringing us closer to the aim of being able to produce tailor-made and extremely low-priced materials, drugs and libraries.

Advanced manufacturing techniques, aimed at implants with high dependability, flexibility, and low manufacturing costs, are crucial in meeting the growing demand for high-quality products like biomedical implants. Incremental sheet forming is a promising flexible manufacturing approach for rapidly prototyping sheet metal components using low-cost tools. Titanium and its alloys are used to shape most biomedical implants because of its superior mechanical qualities, biocompatibility, low weight, and great structural strength. The poor formability of titanium sheets at room temperature, however, limits their widespread use. The goal of this research is to show that gradual sheet formation of a titanium biomedical implant is possible. The possibility of creative and cost-effective concepts for the manufacturing of such complicated shapes with significant wall angles is explored in this study. A numerical simulation based on finite element modeling as well as a design process tailored to metal forming is used to complete the development. The mean of uniaxial tensile tests with a constant strain rate was used to study the flow behavior of the studied material. To forecast the crack, the obtained flow behavior was modeled using the behavior model and failure model.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

The traditional Chinese drug Bombyx Batryticatus mori.L (BBm) which is also named the white stiff silkworm has been widely used in Chinese clinics for thousands of years. It is famous for its antispasmodic and blood circulation promoting effects. Cardiomyocyte hypertrophy, interstitial cell hyperplasia and myocardial fibrosis are closely related to the N-glycosylation of key proteins. To examine the alterations of N-glycosylation that occur in diabetic myocardium during the early stage of the disease and clarify the therapeutic effect of 1-DNJ extracted from BBm, we used the db/db mouse model and an approach based on hydrophilic chromatography solid-phase extraction integrated with an LC-MS/MS identification strategy to perform a site-specific N-glycosylation analysis of left ventricular cardiomyocyte proteins. AGEs, hydroxyproline, CTGF and other serum biochemical indicators were measured with ELISA. In addition, the α1,6-fucosylation of N-glycans was profiled with LCA lectin blots and FITC-labelled lectin affinity histochemistry. The results indicated that 1-DNJ administration obviously downregulated myocardium protein N-glycosylation in db/db mice. The expression levels of serum indicators and fibrosis-related cytokines were reduced significantly by 1-DNJ in a dose-dependent manner. The glycan α1,6-fucosylation level of the db/db mouse myocardium was elevated, and the intervention effect of 1-DNJ administration on N-glycan α1,6-fucosylation was significant. To verify this result, the well-known TGF-β/smad2/3 pathway was selected, and core α1,6-fucosylated TGFR-βⅡ was analysed semi-quantitatively with western blotting. The result supported the conclusions obtained from LCA lectin affinity histochemistry and lectin blot analysis. The expression level of FUT8 mRNA was also detected, and the results showed that 1-DNJ administration did not cause obvious inhibitory effects on FUT8 expression. Therefore, the mechanism of 1-DNJ to relieve the DCM-associated fibrosis can be concluded as the inhibition of N-GlcNAc formation and the reduction of substrate concentration.

The global context of research for new sustainable energy storage technologies makes it a very active sector with significant scientific and economic challenges. Indeed, due to the irregular development of renewable energies and the shutdown of traditional power facilities, it is difficult to maintain a stable balance in terms of supply and demand: energy storage can help in particular for substantial changes in the latter. Metal air batteries have a higher energy density and are safer than other available energy storage devices. Based on the existing and proven lead-acid battery technology, this paper proposed an open cell foam manufactured by the Excess Salt Replication process for use as an anode for lead-air battery cellsies with sulphuric acid as the electrolyte. This will save lead and reduce the battery weight. A 25% antimonial lead alloy was used to produce open cell foams with a cell diameter between 2 mm and 5 mm for the antimonial lead-air battery. Preliminary results of the effective electrical conductivity of self-discharged primary battery cells, measured experimentally, showed that all antimonial lead foam-air battery cellsies performed better than that made from the same dense non porous antimonial lead alloy. This is generally due to their important specific surface area where oxidation-reduction reactions took place. A correlation between the effective electrical conductivity and the cell diameter has been established and the highest conductivity was obtained with a cell diameter of 5mm. The feasibility of such an electrical system has been demonstrated.

This study aims to assess and identify the role of disruptive/digital technologies in financial innovation strategies as part of social innovations at both firm and country level. There are few studies of this type that "cross-examine" technical/social innovative capacity at the firm level vs. the same innovative capacity at the level of the world's major countries. Our proposed study brings some novel elements to the literature on this topic. First, the study synthesizes the factors/variables explaining technical/social innovative capacity as ranked by the GCI (Global Competitiveness Index) and GII (Global Innovation Index) at the country level and then correlates these variables with the factors explaining innovative capacity for the 50 companies in the BCG (Boston Consulting Group) ranking. Second, the study identifies three "driving forces" (digital technologies, managers and the market) as the main variables determining financial innovativeness at firm level. Third, based on the "cross" analysis of the information/data provided by the BCG study vs. the GII and GCI studies, the study suggests some ways to delineate and quantify financial innovation as part of social innovation (e.g., it is argued that 80% of the social innovation achieved annually by a firm relates to the financial relationships engaged by the firm with various categories of stakeholders). Finally, the study is also important from a pragmatic point of view as it suggests/proposes a number of principles that can be considered by managers for building a KM (knowledge management) and continuous innovation strategy. From a theoretical perspective, the study provides a starting point for further research aimed at explaining firm-level financial innovation through the massive use of disruptive technologies.