Choosing the optimal location for a city based on sound environmental geomorphology planning is of the utmost importance to achieving environmental sustainability, as it can spare the State and other decision-making entities a great deal of stress in the long run. GIS offers great potential for environmental planners to choose the most appropriate places for the cities of the future, especially when coupled with environmental geomorphological analyses. The State of Kuwait seeks sustainable development through the implementation of clear and specific urban plans, some of which suffer from a severe lack of geomorphological and spatially based environmental planning. This study aims to: 1) Conduct suitability modelling for establishing new cities in Kuwait, 2) Assess the current 2005-2030 urban plan, and 3) Propose possible recommendations and solutions for potential urban problems. The study relies on integrating several methods to devise a framework that will aid researchers and decision-makers in selecting optimal locations for built structures based on analysis and modelling (e.g., digital elevation model, geologic mapping, geomorphology, natural hazards, heritage/archaeological sites, military areas, oil fields, soils). Using this methodology in choosing city sites contributes to achieving sustainable development, reducing city problems, saving countries’ budgets, and saving lives. Results from this study enhance understanding of how environmental geomorphology, when combined with GIS, can be harnessed to achieve sustainable urban development in the Arabian Gulf countries and other desert countries.

The current study focused on reviewing the rapid growing of using magnetic water in different fields of science and measure the influence of several intensities of magnetization on the chemical and electrical properties of tap water treated by reverse osmosis. The work includes circulation of water for 24 h. in magnetic fields of intensity 500, 1000, 1500, and 2000 G. The magnetization of water causes increasing some positive and negative ions in water such as (Mg, K, Na, Cl¯, Alkaline and SiO₂) and decreasing some positive and negative ions (Ca and SO₃). In the near future, the application of concepts of sustainability development in civil engineering have the to produce structures in harmony with these concepts through using of high-performance materials with less impacts on the environmental and have low cost. The main application of using magnetic water is improvement the geotechnical properties of soil through precipitation of calcite which increases the bond between soil particles and then strength of soil.

The design of highly efficient sensitizers is one of the most significant areas in dye-sensitized solar cell (DSSC) research. We have studied a series of benzothiadiazole-based D-π-π-A organic dyes, putting emphasis on the influence of the donor moiety on the DSSC’s efficiency. Using linear response time-dependent density functional theory (TDDFT) with the CAM-B3LYP functional different donor groups were characterized in terms of electronic absorption spectra and key photovoltaic parameters. As a reference a dye has been considered which has a benzothiadiazole fragment linked via thiophene rings to a diphenylamine donor and a cyanoacrylic acid acceptor. The different systems are first studied in terms of individual performance parameters, which are eventually aggregated into the power conversion efficiency. Here only the amino-substituted species shows a modest increase, whereas the dimethylamino case even shows a decrease.

The State of Kuwait seeks sustainable development through implementation of clear and specific urban plans, some of which suffer from a severe lack of geomorphological and spatially-based environmental planning, such as the use of geographic information systems (GIS). Choosing the optimal location for a city based on sound environmental planning is of the utmost importance to achieving environmental sustainability, as it can spare the State and other decision-making entities a great deal of stress in the long run. GIS, in particular, offers great potential for the environmental planner and decision-maker to choose the most appropriate places for the cities of the future, especially when coupled with geomorphological analyses. To achieve the Vision of Kuwait 2035, one of the State’s planning objectives focuses on Urban Planning for the Establishment of Environmental Cities that Achieve (UPEECA) environmental sustainability criteria. To gain a more holistic analysis related to the Vision, this study aims to: 1) Conduct suitability modelling for establishing new cities in Kuwait, 2) Assess the current 2005-2030 urban plan, and 3) Propose possible recommendations and solutions for potential urban problems. The study relies on integrating several methods to devise a framework that will aid researchers and decision-makers in selecting optimal locations for built structures based on analysis and modelling (e.g., digital elevation model, geologic mapping, geomorphology, natural hazards, heritage/archaeological sites, military areas, oil fields, soils)

With the vast amount of goods being shipped around the world, there is a need to track and manage various types of assets, particularly shipping containers. Logistics industries dealing with small facilities, shipments, equipment, and vehicles must be tracked. There are many applied asset tracking systems such as Radio-Frequency Identification (RFID), Bluetooth Low Energy (BLE) Beacon, and Long-Range Radio (LoRa). This paper presents these systems and focuses on locating assets using LoRaWAN technology, which has a positive impact on the responsive and sustainable cities in Egypt. IoT-based Long Range (LoRa) is a low-power, wide-area communication technology that uses radio frequencies to transmit data over long distances. The extended range, low power consumption, low maintenance, and the ability to store location data when the end node that needs to connect to the asset is out of the gateway's coverage make LoRa a good choice for developing asset-tracking applications. This paper introduces a real-time tracking experiment as a result of a project implementation, whose goals are aligned with industry, innovation, and infrastructure and Sustainable Cities and Communities, the Sustainable Development Goals (SDGs) No. 9 and 11.

All over the world, externally bonded fiber-reinforced polymer systems used to strengthen concrete elements improve building sustainability. However, reports issued by the American Concrete Institute Committee 440 called for heavy scrutinizing before actual field implementation. The very limited number of proposed equations lacks reliability and accuracy. Thus, further investigation in this area is needed. In addition, machine learning techniques are being implemented successfully in developing strength models for complex problems. This study aims to provide a reliable machine learning model based on an experimental database. The proposed model was developed and validated against the experimental database and the very limited models in the literature. The model showed improved agreement with the experimental results compared to the previous models.

The aim of this paper is to analyze the five grand parks in Dubai, United Arab Emirates (UAE) and provide a geoprocessing approach to different aspects such as sport, health, leisure, recreation, and public wellbeing. The study uses a hybrid of qualitative and quantitative approach as methodology. Sustainability offerings, accessibility for people of determination and special needs, typology and the geolocations of the grand parks plays crucial role in residents’ wellbeing. The paper concludes with recommendations for Dubai government to design new and innovative approaches to manage wellbeing of urban public places into the leisure environment for residents.

The increase in incidence of superficial fungal infections combined with the emergence of antifungal resistance represents both a global health challenge and a considerable economic burden. Recently, dermatophytes, the main culprit causing superficial fungal infections, have started to exhibit antifungal resistance. This can be observed in some of the most common species such as Trichophyton rubrum and Trichophyton mentagrophytes. Importantly, the new subspecies, known as Trichophyton indotineae, has been reported to show high resistance to terbinafine, a first-line treatment for dermatophyte infections. Compounding these issues is the realization that diagnosing the causative infectious agents requires using molecular analysis that goes beyond the conventional macroscopic and microscopic methods. These findings emphasize the importance of conducting antifungal susceptibility testing to select the appropriate antifungal necessary for successful treatment. Implementing these changes may improve clinical practices that combat resistant dermatophyte infections.

In the present study, fish were exposed to sub-lethal doses of CuONPs (68.92 ± 3.49 nm) (10, 20, and 50 mg/L) for a long exposure period (25 days). Compared to the control group (0.0 mg/L CuONPs), a significant dose-dependent elevation in blood urea and creatinine values, serum alanine transaminase, aspartate transaminase, and alkaline phosphatase enzyme activities were evident in CuONPs-exposed groups (P < 0.05). Fish exposure to 50 mg/L CuONPs significantly upregulated the transcription of pro-inflammatory cytokines (tumor necrosis factor-alpha, interleukin-1beta, interleukin 12, and interleukin 8), heat shock protein 70, apoptosis-related gene (caspase 3), and oxidative stress-related (superoxide dismutase, catalase, and glutathione peroxidase) genes in liver and gills of the exposed fish in comparison with those in the control group (P < 0.05). Moreover, varying histopathological injuries were noticed in the hepatopancreatic tissues, posterior kidneys, and gills of fish groups correlated to the examined exposure dose of CuONPs. In summary, our results provide new insights and helpful information for better understanding the mechanisms of CuONPs toxicity in Nile tilapia at hematological, molecular levels, and tissue levels.

Mining can impact the environment, biodiversity and human health through direct and indirect practices. This study investigated the effects of gold mining on Gerbillus nanus, pointing to organ dysfunction and redox imbalance. Soil samples, Lycium shawii and G. nanus were collected from a site near a mining planet and a control site. Soil and L. shawii samples from the mining site showed a significant increase cadmium (Cd), cupper (Cu), mercury (Hg), arsenic (As), zinc (Zn), lead (Pb) and vanadium (V). Hepatic, renal and pulmonary Cd, Pb, Hg, Zn, Cu, Fe, As and V concentrations were increased significantly in G. nanus at the mining site. Markers of liver and kidney function were elevated in serum, and several histological manifestations were demonstrated in liver, kidney and lung of G. nanus at the mining site. Malondialdehyde and nitric oxide were increased, and glutathione and antioxidant enzyme were declined in the liver and kidney of G. nanus. In conclusion, mining practices triggered tissue damage and oxidative stress in G. nanus living close to the mining site. These findings can represent the scientific basis for evaluating the environmental and health impact of mining in the on the nearby communities.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Urbanization affects all elements of the pre-urban environment, including soils, hydrology, vegetation, and microclimate. Recently, Saudi Arabia has experienced rapid urbanization and growth. Thus, the country's biodiversity has been threatened. In Riyadh, beetle assemblages were assessed along a rural-suburban-urban gradient. A total of 2,791 individuals from 94 species belonging to seven families were collected at 15 sites along three different gradients of urbanization in Wadi Hanifa. Tenebrionidae dominated abundance (60.1%) and richness (38%). Beetle abundance, evenness, and diversity were not different among habitats; however, species richness was higher in rural habitats. DCA and CCA analyses showed distinct differences among sites along gradients. Urbanization intensity, soil variables, and land cover were significantly correlated with DCA axis 1, while elevation and flora were significantly correlated with DCA axis 2. The most critical operating environmental variables in Wadi Hanifa were buildings, elevation, soil organic carbon, litter cover, and litter depth, as well as plants such as Launaea capitata, Lycium shawii, Alhagi graecorum, and Heliotropium currasavicum. Ten species in our study are associated with urban habitats, six with suburban habitats, and seven with rural habitats. Consequently, expanding urban areas may negatively affect the richness and composition of beetles and may result in the loss of some native species.

Environmental deterioration factors are constantly increasing, causing unwanted aesthetic changes to stone artworks due to exposure to various physical and chemical deterioration factors. Inorganic nanoparticle-filled polymer composites have extended their multiple functionalities to various applications, including cultural heritage conservation. Therefore, this study has examined the effects of clay, SiO2, Ca(OH)2 and CaCO3 nanomaterials in the enhancement of the physicomechanical properties of limestone monuments, the aim of the present work being to evaluate comparatively the effectiveness of nanoparticles as consolidation and protection material for limestone artworks. The nanoparticles were added to an acrylic-based copolymer (polyethylmethacrylate (EMA)/methylacrylate (MA) (70/30), in order to improve its physiochemical and mechanical properties, and produced a significant improvement in the ability of the polymers to consolidate and protect the stone. The synthesis process of nanoparticles/polymer nanocomposite has been prepared by an in situ emulsion polymerization system. The nanocomposites contained poly (EMA/MA) with a solid content of 3% [poly (EMA/MA)] in the absence and presence of 5% nanoparticles (0.15 g nanoparticles). Samples were subjected to artificial aging by relative humidity/temperature and acid/salt crystallization weathering to show the optimum conditions of durability and the effectiveness of the nano-mixture in improving the physical and mechanical properties of the stone material. To ensure that the treatment had no negative effects on the physical characteristics of the limestone, the properties of the treated limestone samples were evaluated comparatively before and after artificial aging by the conduct of microstructural (phase morphology studied by means of scanning electron microscopy) and aesthetic (colour and lightness measured by spectrophotometry) analyses. Also used were measurement of static contact angle of water droplets on the surface of the samples, total immersion water absorption, compressive strength, and abrasion resistance test. Results demonstrated that the addition of nanoparticles to an acrylic-based polymer enhanced its capability to consolidate and protect the limestone samples.

Rising fuel costs, significant air pollution, and the need to mitigate the negative consequences of oil consumption have diminished the relevance of traditional vehicles. This shift encourages the adoption of safer, more efficient, and eco-friendly transportation alternatives, such as fuel cell, electric, and hybrid vehicles. Brushless direct current motors are gaining popularity due to their high efficiency, power factor, torque, and controllability. By 2030, Brushless Direct Current motors are expected to replace conventional motors as the standard for power transfer, especially in dynamic applications like automobiles, more electric aircraft. This study explores a control technique to improve real-time control of brushless direct current motors in electric vehicles It presents speed control of these system for electric vehicle applications and an overview of electric vehicle technologies. A model for the 120-degree mode was developed using electrical and mechanical equations in MATLAB/Simulink. Three scenarios were examined to assess the potential of controlling brushless direct current motors using constant and dynamic speed and torque. The actual value reached the reference value in the first two scenarios.

Reaction of 2-mercapto-3-phenylquinazolin-4(3H)-one (MPQ) with both 4-vinyl benzyl chloride and allyl bromide furnished the reactive heterocyclic monomers 3-phenyl-2-((4-vinylbenzyl) thio) quinazolin-4(3H)-one (PVTQ) and 2-(allylthio)-3-phenylquinazolin-4(3H)-one (APQ), respectively. Copolymerization of PVTQ monomer with styrene and methyl methacrylate in the presence of 2,2′-azobisisobutyronitrile (AIBN) afforded the copolymers PS-co-PPVTQ and PMMA-co-PPVTQ, respectively. Similarly, copolymerization of monomer APQ with styrene and methyl methacrylate (MMA) afforded the copolymers PS-co-PAPQ and PMMA-co-PAPQ, respectively. The resulted copolymers were characterized by using FT-IR, 1H-NMR and GPC techniques. Silver nanocomposites of PS, PMMA, PS-co-PPVTQ, PMMA-co-PPVTQ, PS-co-PAPQ and PMMA-co-PAPQ were synthesized by the addition of silver nitrate into the polymer solution. The reduction of silver ions into silver nanoparticles was performed in DMF and water. Thermogravimetric (TGA) analysis was used to determine the thermal stability of the copolymers and their silver nanocomposites. The X-ray diffraction (XRD) analysis indicated the amorphous structures of the co-polymers and confirmed the formation of silver nanoparticles. The antitumor and antibacterial activities were screened for the copolymers and enhanced by the formation of their silver nanocomposites. In vivo antitumor activity in Ehrlich Ascitic Carcinoma (EAC) mice model showed that PS-co-PPVTQ/Ag NPs, PMMA-co-PPVTQ/Ag NPs, and PMMA-co-PAPQ/Ag NPs displayed promising inhibitory effects against EAC and induce apoptosis against MCF-7 cells.

This study compared the Biodentine (BD) and MTA in repair of furcation perforation (FP) in a dog model in terms of inflammatory cell count and new hard tissue formation through histological and immunohistochemical evaluations. Ninety six teeth in six adult mongrel dogs were divided according to the time of repair into two groups (48 teeth/3 dogs each); immediate and delayed repair of the induced FP. Each group was divided into three subgroups (16 teeth each) according to the evaluation periods; 1, 2, and 3 months. Each subgroup was further subdivided into four subdivisions according to the material used; MTA (6 teeth), Biodentine (6 teeth), negative control (2 teeth) and positive control (2 teeth). In experimental and positive control samples, the teeth were instrumented and obturated then, a FP was performed. The perforations were sealed according to the groups and subdivisions. Histopathology and immunohistochemical analysis using Osteonectin antibodies were performed for assessment of the inflammatory cell count and new hard tissue formation. In all groups and subgroups, there were no significant differences between MTA and BD in the inflammatory cell count and new hard tissue formation (P>0.05). Biodentine can alternate the MTA as a FP repair material.

As the number of ships for marine transportation increases with the advancement of global trade, encountering multiple ships in marine traffic becomes common. This situation raises the risk of collision of the ships; hence this paper proposes a novel Fuzzy-logic based intelligent conflict detection and resolution algorithm, where the collision courses and possible avoiding actions are analyzed by considering ship motion dynamics and the input and output fuzzy membership functions are derived. As a conflict detection module, the Collision Risk (CR) is measured for each ship by using a scaled nondimensional Distance to the Closest Point of Approach (DCPA) and Time to the Closest Point of Approach (TCPA) as inputs. Afterwards, the decisions for collision avoidance are made based on the calculated CR, encountering angle and relative angle of each ship measured from others. In this regard, the rules for the Fuzzy interface system are defined in accordance with the COLREGs, and the whole system is implemented on the MATLAB Simulink platform. In addition, to deal with the multiple ship encounters, the paper proposes a unique maximum-course and minimum-speed change approach for decision making, which has been found to be efficient to solve Imazu problems, and other complicated multiple-ship encounters.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

Water microbial contamination is a serious issue that poses a risk to both animal and human health. 120 water samples collected from main water source and drinkers from a poultry farm. Different bacterial pathogens were isolated from water sources. Escherichia (E.) coli, Pseudomonas (P.) aureoginosa, (Salmonella) S. Typhimurim, Aeromonas (A.) hydrophila at different percentages. Variable degree of bacterial resistance to some commercial disinfectants commonly used to disinfect water system (iodine, terminator and H2O2). Nanoparticles were used to control bacteria in water. About the safety investigation for the prepared nanomaterials, the work results demonstrated that zinc oxide (ZnO) nanoparticles (NPs) exhibit the highest safety profile among the manufactured materials. The median fatal dose (LD50) for ZnO NPs was determined to be 3709 mg/kg body weight. In comparison, the LD50 values for zeolites and nanocomposites were 3251 mg/kg and 2658 mg/kg, respectively. Therapeutic dosages were estimated based on the LD50. Zeolite NPs, ZnO NPs and ZnO/zeolite NPs showing promising results in control of those bacteria. It was concluded that the escalating resistance of bacteria to disinfectants have led to a need to find alternative such as nanoparticles that proved promising results in control of pathogens, particularly it showed a safe effect on laboratory animals.

A comparative efficacy of apathogenic genotype I (V4) and lentogenic genotype II (LaSota) strains of live Newcastle disease virus (NDV) vaccines was done following vaccination with pathogen-associated molecular pattern (PAMP) H9N2 avian influenza vaccine and challenge with velogenic NDV genotype VII.1.1 (vNDV-VII.1.1). Eight groups (Gs) of day-old chicks were used (n=25). Groups 1-4 received a single dose of PAMP-H9N2 subcutaneously, while Gs (1, 5) and (2, 6) received eye drops of V4 and LaSota respectively as twice doses. All Gs except 4 and 8 were intramuscularly challenged with vNDV-VII.1.1 at 28th days of age. No signs were detected in Gs 1, 5, 4, and 8. The mortality rates were 0% in Gs 1, 4, 5, and 8; 40% in G2; 46.66% in G6; and 100% in Gs 3 and 7. Lesions were recorded as minimal in Gs 1 and 5, but mild to moderate in Gs 2 and 6. The lowest significant viral shedding was detected in Gs 1, 2, and 5. In conclusion, two successive vaccinations of broilers with a live V4 NDV vaccine provided a higher protection against vNDV-VII.1.1 challenge than LaSota. Besides, PAMP-H9N2 with live NDV vaccines induced more protection than live vaccine alone.

Existing implants used with Total Knee Arthroplasty (TKA), Total Hip Arthroplasty (THA), and other joint reconstruction treatments, have displayed premature failures and frequent needs for revision surgery in recent years, particularly with young active patients who represent more than 55% of all joint reconstruction patients. Bone cement and stress shielding have been identified as the major reasons for premature joint failures. A breakdown of the cement may happen, and revision surgery may be needed because of the aseptic loosening. The significant mismatch of stiffness properties of patient trabecular bones and metallic implant materials in joint reconstruction surgery results in the stress shielding phenomenon. This could lead to significant bone resorption and increased risk of bone fracture and the aseptic loosening of implants. The present project introduces an approach for development of customized cellular structures to match the mechanical properties and architecture of human trabecular bone. It consists of four modules:1- characterization of geometry, microarchitecture, and stiffness properties of patient’s bones; 2- developing customized lattice structures tailored to mimic properties established in module 1; 3 - integration of developed lattice structure into full scale implant design and manufacturing; 4- implementation of the developed technology for use in implants that would overcome most of the issues related to aseptic loosening phenomenon. The present work aims at fulfilling the objectives of module 2 by exploring new designs of customized lattice structures and texture tailored to mimic closely patients’ bone anisotropic properties and that can incorporate an engineered biological press-fit fixation technique. The effects of various lattice design variables on mechanical performance of the structure are examined through systematic experimental plan using statistical design of experiments technique and analysis of variance method. All tested lattice designs were explored under realistic geometrical, biological, and manufacturing constraints. Of the four design factors examined in this study, strut thickness was found to have the highest percent contribution (41%) regarding the structure stiffness, followed by unit cell type, and cell size. Srut shape was found to have the lowest effect with only 11% contribution. The introduced solution offers lattice structure designs that can be adjusted to match bone stiffness distribution and promote bone ingrowth and hence eliminating the phenomenon of stress shielding while incorporating biological press-fit fixation technique.

Background: Antibiotic resistance is an urgent issue everywhere in the globe. It is necessary to look into new sources of antibiotics to address this issue. Aim of the study: studying the purification of Corallopyronin B from various soil conditions in Egypt, as well as the antibacterial effectiveness of Corallopyronin B in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Several soil conditions in Egypt were examined to create bacterial isolates that generated the antibiotic chemical Corallopyronin B. Using reversed-phase HPLC, Myxopyronin B was purified. The test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity were ascertained using the paper disc diffusion assay and the broth microdilution technique. Furthermore, in stages 1/2 of randomized clinical trials including human and animal models, pharmacokinetics, adverse drug reactions, and the in vivo antibacterial spectrum were discovered. Results: The soil bacterial isolate Corallococcus coralloides DSM 2259, which was grown on a Casein yeast peptone( CYP) plate, produced Corallopyronin B from its culture supernatant. At MICs more than 100 mcg/ml, the test antibiotic inhibited the growth of many Gram -ve bacteria, including Escherichia coli, while also preventing the growth of numerous Gram +ve bacteria, with MICs ranging from 1 to 10 mcg/ml. Eukaryotic cells, on the other hand, including those in humans and fungi, were unharmed. The test antibiotic was shown to have a bactericidal effect by inhibiting bacterial DNA-dependent RNA polymerase( RNLP). In phases 1/2 of randomized human clinical trials, when 600 mg of the dose per 70 kg of body weight was administered SC, the Cmax was 8.6 mcg/ml at Tmax 1 hour; T1/2 reached 136 min following first-order kinetics of elimination. It stopped acting around 6-7 hours after SC was administered. In the preclinical and randomized human clinical trial phases 1/2, less than 6 percent of experimental candidates had uncommon toxicity, which showed up as reduced bile flow. Protein binding with plasma albumin was detected which reached about 83%. Conclusion: The current work was noteworthy since it involved the production of the bactericidal antibiotic Corallopyronin B from Corallococcus coralloides DSM 2259 which was isolated from several soil environments in Egypt.

Serious outbreaks of foodborne disease have been caused by Listeria monocytogenes found in retail delicatessens and the severity of disease is significant, with high hospitalization and mortality rates. Little is understood about the formidable public health threat of L. monocytogenesin all four niches, humans, animals, food and environment in Egypt. This study analyzed the presence of L. monocytogenes collected from the four environmental niches and bioinformatic analysis was implemented to analyze and compare the data. PCR was used to detect virulence genes encoded by pathogenicity island (LIPI-1). prfA amino acid substation that causes constitutive expression of virulence was common in 77.7% of isolates. BLAST analysis did not match other isolates in the NCBI database suggesting this may be a characteristic of the region associated with these isolates. A second group included the NH1 isolate originating in China, and BLAST analysis showed this prfA allele was shared with isolates from other global locations such as Europe and North America. Identification of possible links and transmission pathways between the four niches, helps to decrease the risk of disease in humans, to take more specific control measures in the context of disease prevention, to limit economic losses associated with food recalls and highlightens the need to treatment options.

Purpose: To evaluate the efficacy and survival rates of same session ab interno trabeculectomy with the trabectome and Ahmed glaucoma valve implant (AT) in comparison to the Ahmed glaucoma valve alone (A). Method: A total of 107 eyes undergoing primary glaucoma surgery were enrolled in this retrospective comparative case series, including 48 eyes which underwent AT and 59 eyes which received A alone. Participants were identified using the procedural terminology codes, and their medical records were reviewed. The primary outcome measure was surgical success, defined as intraocular pressure (IOP) > 5 mmHg, ≤ 21 mmHg, and IOP reduction ≥ 20% from baseline at two consecutive visits after three months, no reoperation for glaucoma. Secondary outcome measures were IOP, the number of glaucoma medications, incidence of a hypertensive phase, and best corrected visual acuity (BCVA). Results: The cumulative probability of success at one year was 70% in AT, and 65% in A (p=0.85). IOP decreased significantly from 26.6 ± 10.1 mmHg at baseline to 14.7 ± 3.3 mmHg at the final follow-up in AT (p= 0.001). The corresponding numbers for A were 28.8 ± 10.2 and 16.7 ± 4.9, respectively (p= 0.001). The final IOP was significantly lower in AT (p= 0.022). The number of medications at baseline was comparable in both groups (2.6 ± 1.2 in AT and 2.5 ± 1.3 in A, p=0.851). Corresponding number at 1 year visit was 1.2±2 in AT and 2.8±1.8 in A (p=0.001). The incidence of a hypertensive phase was 18.7% in AT and 35.5% in A (p=0.05). HP resolved in only 30% of eyes. The criteria for HP resolution were fulfilled in 9 eyes (30%). There was no difference in the rate of resolution of the hypertensive phase between AT and A (33.3% and 28.5%, respectively, p=0.67). Conclusion: Ahmed glaucoma valve implant with same session trabectome surgery significantly decreased the rate of the hypertensive phase and postoperative IOP as well as the number of glaucoma medications.

In Nigeria, desertification has become one of the most pronounced ecological disasters, with the impacts mostly affecting eleven frontline States. This has been attributed to a range of both nat-ural and man-made factors. This study applied a remote sensing-based change detection and indicator analysis to explore land use/land cover changes and detect major conversions from ecologically active land covers to sand dunes. Results indicate that areas covered by sand dunes (a major indicator of desertification) have doubled over the 25 years under consideration (1990 to 2015). Although about 0.71 km2 of dunes have been converted to vegetation, indicative of the success of various international, national, local, and individual afforestation efforts, conversely about 10.1 km2 of vegetation were converted to sand dunes, implying around 14 times more de-forestation compared to afforestation. Juxtaposing the progression of sand dune with climate records of the study area and examining the relationship between indicators of climate change and desertification suggested a mismatch between both processes as increasing rainfall and lower temperatures observed in 1994, 2005, 2012, and 2014 did not translated into positive feedbacks for desertification in the study area. On average, our results reveal that sand dune is progressing at a mean annual rate of about 15.2 km2 in the study area. Based on this study’s land cover change, trend and conversion assessment, visual reconciliation of climate records with land cover data, statistical analysis, observations from ground-truthing, as well as previous literature, it can be inferred that desertification in Nigeria is less a function of climate change, but more a product of human activities driven by poverty, population growth and failed government policies. Further projections by this study also reveal a high probability of more farmlands being converted to sand dunes by the year 2030 and 2045 if current practices prevail.

Water stress (drought and waterlogging) is drastic abiotic stress to plant growth and development. Melatonin, bioactive plant hormone, has been widely tested in drought situations in diverse plant species, while a few studies on the role of melatonin in waterlogging stress conditions have been published. In the current review, we analyze the bio-stimulatory functions of melatonin on plants under both drought and waterlogging stress. Melatonin controls the levels of reactive oxygen and nitrogen species and positively changes the molecular defense to improve plant tolerance against drought and waterlogging stress. Moreover, the crosstalk of melatonin and other phytohormones is a key element on plant survival under drought stress, while this relationship needs further investigation under waterlogging stress. In this review, we draw the complete story of water stress on both sides: drought and waterlogging through discussing the previous critical studies under both conditions. Moreover, we suggest several research directions, especially for waterlogging, which remains a big vague piece of melatonin and water stress puzzle.

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

Background: Antibiotic resistance is an overwhelming serious difficulty globally. This necessitates the exploration of novel sources of antibiotics to overcome this challenge. Aim of the study: Bacterial Myxopyronin A production from various soil environments Egypt; as well as testing its antimicrobial activity in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Different soil environments in Egypt were screened for the growth of bacterial isolates producing Myxopyronin A as an antimicrobial agent. Purification of Myxopyronin A was performed via reversed-phase HPLC. Paper disc diffusion assay, as well as the Broth dilution technique, were exploited to assess the invitro antimicrobial and minimum inhibitory concentration( MIC) of the test antibiotic. Furthermore, in vivo antimicrobial spectrum, adverse drug reactions, and pharmacokinetics were detected during animal model testing stages and human randomized clinical trials phases 1/2. Results: From the culture supernatant of the Myxobacterium Myxococcus fulvus 124B02 which was the predominant soil bacterial isolate grown on the Casein yeast peptone plate, Myxopyronin A was produced. The test antibiotic blocked the growth of many Gram +ve bacteria with MICs less than 100 mcg/ ml. In contrast, it inhibited the growth of a few Gram -ve bacteria such as Escherichia coli at MICs greater than 100 mcg/ ml. On the other hand, Eukaryotic cells such as fungal and human cells were not affected. Prokaryotic DNA-dependant-RNA polymerase( RNLP) was noticed to be inhibited via the test antibiotic suggesting its bactericidal action. The maximum concentration was 7-8 mcg/ ml at a maximum time of 2 hours when 600 mg dose was orally administered in randomized human clinical trials phases 1/2, and T1/2 reached 2.5 hours following first-order kinetics of elimination. The duration of its action was nearly 12 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and cholestatic jaundice in less than 5 % of experimental candidates. Conclusion: The present study was promising due to the bactericidal antibiotic Myxopyronin A production from Myxococcus fulvus 124B02 isolated from different soil environments in Egypt.

1) Background: The aim was to evaluate the bioefficacy of vitamin D (VitD) encapsulated in nanoemulsions developed by sonication and pH-shifting of pea protein isolate in restoring VitD status in VitD-deficient rats. 2) Methods: Weaned (3-week old), male albino rats (n = 35) were initially divided into two groups: control sufficient group (VDS; n = 7) fed on a normal AIN-93G diet and a VitD-deficient group (n = 28) fed a VitD-deficient diet for six weeks. VitD-deficient rats were divided into four subgroups: two treatment groups (Nano+VitD and Oil+VitD) and two control groups (Nano-VitD and Oil-VitD), receiving seven rats in each sub-group. Nano+VitD and Oil+VitD groups received VitD dispersed in PPI-nanoemulsions and in canola oil, respectively, while the control groups received the respective delivery vehicles without VitD. Serum 25-hydroxyvitamin D [25(OH)VitD], parathyroid hormone (PTH), calcium (Ca), phosphorus levels (P), and alkaline phosphatase (ALP) activity were measured. Femur bone was used to prepare histopathological sections. 3) Results: After one week of treatment, the VitD-deficient rats consuming Nano+VitD recovered from VitD deficiency (serum 25(OH)VitD 34.38 ± 7.00) compared to the sufficient control (36.84 ± 9.16; p > 0.05) and the deficient control consuming VitD+Oil (14.05 ± 3.08; p < 0.01). Enhancement in VitD status was followed with expected changes in serum PTH, Ca, P, and ALP levels, no difference in similar biomarkers against the sufficient control, and an improvement of the osteoid area and reduction of trabecular separation in bone. 4) Conclusions: Stabilization of VitD within PPI-based nanoemulsions enhances its absorption and restores its status and biomarkers of bone resorption in VitD-deficient rats.

Background: As the impacts of diabetes-induced reproductive damage are now evident in young people, we are now in an urgent need to devise new ways to protect and enhance the reproductive health of diabetic people. The purpose of this study was to assess the protective impact of enalapril (an ACE inhibitor) and paricalcitol (a vitamin D analogue) alone and in combination, on streptozotocin (STZ) diabetes-induced testicular dysfunction in rats. Material and methods: This study was carried on 50 male Sprague-Dawley rats; 10 normal rats were allocated as non-diabetic control group. 40 rats developed diabetes after receiving a single dose of STZ, then the diabetic rats were divided into four groups of equivalent number assigned as diabetic control, enalapril treated, paricalcitol treated, in addition to combined enalapril and paricalcitol treated groups. The effects of mono and combined therapy with paricalcitol and enalapril on testicular functions, sperm activity, glycemic state oxidative stress and inflammatory parameters as well as histopathological examination were assessed when compared to the normal and diabetic control rats. Results: As a result of diabetes induction, epididymal sperm count, sperm motility, serum levels of testosterone, follicle stimulating hormone (FSH) as well as luteinizing hormone (LH) and the antioxidant enzyme activities were significantly decreased, while abnormal sperm (%), insulin resistance, nitric oxide (NO), malondialdehyde (MDA), interleukin-6 (IL-6) as well as tumor necrosis factor-α (TNF-α) were significantly increased, along with sever distortion of testicular structure. Interestingly, treatment with paricalcitol and enalapril either alone or in combination significantly improved the sperm parameters, increased antioxidant enzyme activities in addition to serum levels of testosterone, FSH and LH, reduced insulin resistance, IL-6 and TNF-α levels and finally ameliorated the diabetes-induced testicular oxidative stress and histopathological damage with somewhat superior effect for paricalcitol monotherapy and combined therapy with both drugs than monotherapy with enalapril alone. Conclusion: Monotherapy with paricalcitol and its combination therapy with enalapril has a somewhat superior effect in improving the diabetes-induced testicular dysfunction (most probably as a result of their hypoglycemic, antioxidant, anti-inflammatory and anti-apoptotic properties), than monotherapy with enalapril alone in male rats, recommending a synergistic impact of both drugs.

المستخلص تصنيع لقاح مكون من الحمض النووي الريبوزي الرسول الخاص بالبروتينات المسئولة عن انتاج البروتينات نيورامنيديز والهيم اجليوتونين لفيروسي الانفلونزا الخنازير والطيورمحاط بجزيئات دهنية بحجم النانوميتر عدوى انفلونزا الخنازير وانفلونزا الطيور مشكلة خطيرة تؤرق العالم كله هذه الايام خصوصا انها مميتة لكثير من اطفال العالم . بعد فترة التعافي من الاصابة تتكون المناعة المكتسبة ضدها لمدة عام تقريبا. هذه الانفلونزا تسبب تسمم فيروسي في الدم بالاضافة للالتهاب الرئوي وهذامن بين اكبرالاسباب للوفاة بين الاطفال قبل سن عامين عالميا بشكل مباشر. الهدف من الدراسة هو انتاج لقاح الحمض النووي الريبوزي الرسول من نوع الام بالنانوتكنولوجي لبروتينات الهيم اجليوتونين والنيورامنيديز الموجودة على سطح هذه الفيروسات التي تساعدتها في الاتصاق بالعائل الذي ستتكاثر داخل خلاياه بالجهاز التنفسي. هذه الدراسة دراسة استكشافية ومن خلالها استطاعنا تصميم هذا اللقاح باستعمال نظام توصيل للقاح بالنانوتكنولوجي حجم جزيئاته 70نانوميمتر. اللقاح الجديد اظهر فاعلية بنسبة 60% واظهر فاعلية حيوية مقاربة واثار جانبية اقل بالمقارنة باللقاحات المتوفرة حاليا بالسوق الدوائي ضد هذا النوع من الفيروسات الوبائية. ABSTRACT Background: Worldwide, Swine and Avian influenza, or the H1N1 and H5N1 serotypes of the Influenza A virus, is a highly contagious illness. In recent years, the global incidence of mortality rate has surpassed 284,000 fatalities. Aim of the study: The production of mRNA vaccine lipid nanoparticles (LNP) to combat the deadly strains of Avian and Swine influenza (H1N1 and H5N1 of the influenza A serotype). Methodology: Polymerase chain reaction (PCR) was used to clone genes of interest encoding Haemagglutinin (HA) and Neuraminidase (NA) of Influenza A virus strains (H5N1 and H1N1) known as Avian flu and Swine flu, respectively. The genes were then inserted using the EcoR1, BAM Hind II restriction endonuclease type II, and Ligase enzyme into the pET-21(+) transcription vector plasmid. On the other hand, the hybrid transcription vectors were mixed with T7 RNA polymerase and ribonucleotides within a test tube after being linearized using EcoR II. Following their purification via reversed-phase high-performance liquid chromatography (RP-HPLC), the mRNAs of the HA and NA were encased in 70 nm LNPs and subjected to reverse-phase high-performance liquid chromatography (RP-HPLC). Lastly, immunogenicity studies were performed in stages 1/2 of randomized human and preclinical clinical trials. Results: The bivalent vaccination had around 63% efficacy in preclinical studies and approximately 60% efficacy in randomized human clinical trials. As shown by the ELISA test, strong neutralizing antibodies against HA were prevalent. Conclusion: The current study is a promising effort because of the development of the novel LNP-mRNA vaccine, which could lower the incidence of Avian and Swine flu infectious disorders.

Exotic plants are usually problematic for the native species where they coexist. This study evaluated the effect of naturalised alien Cenchrus echinatus L. on native plants in the urban vegetation. A field trial was conducted to assess the effect of this species on cover and diversity of the native vegetation. The allelopathic potential of such species was examined. Plots comprising C. echinatus had lower cover of some native species. Lower floristic diversity was observed at more dense cover of this plant. The soil under Cenchrus attained lower N, P and K contents. This soil had no effect on germination and growth of the native species. It also comprised germinable seeds of some species which were absent from the standing vegetation. Exotic C. echinatus may exert a negative effect on the native vegetation of the urban plant communities. Dense cover of Cenchrus may inhibit germination of native species, leading to reduction in their cover. The reduction in cover and diversity of native species was not attributed to allelopathy. These results suggest that naturalised C. echinatus may be more competitor than the native ones, particularly at higher densities. Furthermore, it may represent a threat for the native plants in the urban vegetation.

We report the isolation of two novel degrading bacterial strains active against the potential environmental pollutant acetamino-phen/paracetamol. Streptomyces Chrestomyceticus (RS2) and Streptomyces Flavofuscus (M33) collected from El-Natrun Valley, Egypt, water, sediment, and sand samples were taxonomically characterized via conidiophores morphologic characterization under Trans-mission Electron Microscope (TEM). Genotypic identification, done based on their 16S rRNA gene sequence analysis followed by BLAST alignment and deposited on the NCBI as 2 novel strains. The phylogenetic tree was constructed using an appropriate software. Acetaminophen degradation-products chemical structure was identified by GC/LC MS. The biological antimicrobial activity of some selected acetaminophen degradation-products extracts and derived compounds was examined against panel of test micro-organisms and found to be have high anti-microbial effect. In addition, in silico cheminformatics Swiss ADMET evaluation of these selected deg-radation extract for gastric absorption, distribution, hepatic metabolism, renal excretion as well as distribution to CNS and finally not mutagenic/teratogenic or genotoxic virtually. In vitro cytotoxic activity of these selected bio-degradation products was performed against HepG2 and MCF7 cancer cell lines, revealing that M33 and RS2 extract effect on acetaminophen/paracetamol bio-degradation products are potentially safe with higher IC50 on HepG2 and MCF7, in comparison to acetaminophen/paracetamol with IC50 of 108.5 μg/ml. Moreover, the in vivo acute oral single dose toxicity experiment was conducted, being compared with acetamino-phen/paracetamol to confirm that the bio-degradation products have lower toxicity than acetaminophen in vivo and in silico.

Background: Breast cancer and other neoplasms like acute lymphocytic leukemia pose a serious threat to public health worldwide. Treatment for malignancies including acute lymphocytic leukemia and breast cancer requires enzymes that break down L-glutamine. An amidohydrolase called L-glutaminase can be an effective chemotherapeutic tool for treating various cancers. Methods: On mineral L-glutamine agar selective medium (MGA), a few bacterial isolates were examined in the current investigation to see if they produced L-glutaminase. However, the most effective positive bacterial isolates generating L-glutaminase were identified using morphological and biochemical testing. Molecular detection using the direct Southern blotting approach was also used to determine the main positive isolate that produces L-glutaminase. L-glutaminase synthesis by bacteria was evaluated for its characteristics. Using an MTT test, the anticancer activity was evaluated. Results: exclusive bacterial isolates that used L-glutamine as their sole source of metabolic nitrogen exhibited favorable growth on MGA. PH 7.4 and a temperature of 37 0C were the ideal environmental and physiological conditions for developing positive bacterial isolates. From the soil samples taken from various soil conditions in Egypt, the morphological and biochemical analyses showed that Bacillus cereus 14579 was the main positive bacterial generating L-glutaminase isolate. At a pH of 7.4 and a temperature of 37 °C, the following activators—KCL, ZnSO4, FeSO4, K2HPO4, and MgSO4—provided the high-grade circumstances for characterizing L-glutaminase synthesis. Bacillus cereus-produced L-glutaminase has shown excellent bioavailability and effectiveness as an anticancer therapy. The yield [productivity] was 5.2 U/ml during the original manufacture from MGA, but it increased to 42.96 U/ ml by bacterial recombinant DNA manufacturing. The molecular mass of L-glutaminase was roughly 37 KDa. L-glutaminase was purified, yielding final enzyme recovery of 55 1.23%, total activity 12,990± 19.76 ( U), specific activity 384.66± 8.92( U/ mg of protein), and purification fold 2± 2.99. Furthermore, the L-glutaminase activity was raised by 19%, 23%, 15%, and 9%, respectively, by the enzymatic activators Mn2+, K+, Na+, and Fe3+. It demonstrated strong DPPH scavenging activity (IC50 = 61 μg/ mL) and anticancer activity( IC50 = 40.72, 9.7, 7.39, 20.61, 51.28, and 11.55 μg/ mL, respectively) against human liver (HepG-2), colon ( HCT-116), breast ( MCF-7), lung( A-549), lymphocytic( CCL-120), and cervical( Hela) cancer cell lines. A stronger affinity for its substrate was shown by the kinetic parameters of Km and Vmax, which were 13.2 10-5 M and 119.86 μmol/ ml/ min, respectively. Conclusion: Acute lymphocytic leukemia and breast cancer are examples of auxotrophic malignancies for which L-glutamine serves as the only metabolic source, and L-glutaminase generated by Bacillus cereus was an appropriate enzyme in the therapy of these diseases.

Background: RSV, or respiratory syncytial virus, is a deadly condition that is present all over the world today. The infection is initially contained in the lower respiratory tract without systemic transmission. The objective of the study: Bioinformatics was used in Egypt to create an mRNA vaccine against the Respiratory syncytial virus (RSV). Methodology: In the present screening experimental study, a lipid nanoparticles vaccine of mRNA of the surface fusion protein of Respiratory syncytial virus was manufactured. The present vaccine delivery system was lipid nanoparticles with a particle size of approximately 90 nanometres, manufactured by the hot micro-emulsion method. In stages 1 and 2 of clinical trials, the immunogenicity of the current mRNA RSV vaccine was evaluated. Results: The current vaccine demonstrated 81% immunogenicity in animal testing, but only 69% in stages 1 and 2 of clinical trials. Its side effects were manageable. The results persisted for a while. In the current trial, the vaccination proved effective as a preventative measure against RSV infection. The current vaccination lacked antibody-dependent enhancement, which causes non-protective antibodies to develop. These non-neutralizing antibodies exacerbate infection by activating cytokines and complement cascade through the formation of immune complexes or enhancement of the virus entry and replication in the host cells. On the other hand, the current RSV mRNA vaccine of the surface fusion protein consequent on the production of powerful neutralizing antibodies with prolonged immunity especially to infants and elderly candidates who received the optimal dosage regimen.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

Natural product especially secondary metabolites that produced by plants under the stressed condition shown to have a different pharmacological impact. Aeluropus lagopoides is one of the typical halophyte plants survivals under stressed conditions. It has been used for wound healing and as a painkiller. The bioactivity and the chemical composition of this plant have poorly investigated. Consequently, chemical components of A. lagopoides leaves were extracted using hexane (nonpolar), ethyl acetate (semi-polar), n-butanol (polar) to extract the most extensive variety of metabolites. The cytotoxicity and anticancer impact of extracted secondary metabolites evaluated against breast (MCF-7), colon (HCT-116), and liver (HepG2) cancer cell lines using SRB test. The mechanism of action verified by observing the appearance of apoptotic bodies using the fluorescent microscope while their antiproliferative impact had been evaluated using flow cytometer. Results revealed that secondary metabolites extracted using hexane and ethyl acetate were having the highest cytotoxicity and thus anticancer activity effect on HepG2 with IC₅₀ (24.29 ± 0.85, 11.22 ± 0.679 µg/mL) respectively. Where apoptotic bodies observed, flow cytometer results exhibited that secondary metabolites can inhibit cell cycle in G0/G1 phase. Accordingly, A. lagopoides hexane and ethyl acetate extracts may consider as a candidate anti-cancer drug.

Machine Learning has completely transformed health care system, which transmits medical data through IOT sensors. So it is very important to encrypt them to protect patient data. encrypting medical images from a performance perspective consumes time; hence the use of an auto encoder is essential. An auto encoder is used in this work to compress the image as a vector prior to the encryption process. The digital image passes across description function and a decoder to get back the image in the proposed work; various experiments are carried out on hyper parameters to achieve the highest outcome of the classification. The findings demonstrate that the combination of Mean Square Logarithmic Error as the loss function, ADA grad as an optimizer, two layers for the encoder, and another reverse for the decoder, RELU as the activation function generates the best auto encoder results. The combination of Mean square error (lose function), RMS prop (optimizer), three layers for the encoder and another reverse for the decoder, and RELU (activation function) has the best classification result. All the experiments with different hyper parameter has run almost very close to each other even when changing the number of layers. The running time is between 9 and 16 second for each epoch.

Superficial mycoses, encompassing a range of fungal infections affecting the outer layers of the skin, hair, and nails, have become increasingly prevalent in recent years. While these infections are generally non-life-threatening, the emergence of antifungal resistance poses a growing threat to effective treatment strategies. In this article we explore the escalating specter of antifungal resistance in superficial mycoses, focusing on the underlying mechanisms driving resistance, the clinical implications, and potential avenues for mitigation. The rise of antifungal resistance in superficial mycoses is multifactorial. Consequently, the efficacy of conventional treatments is diminishing, leading to persistent or recurrent infections. Understanding the molecular mechanisms underlying antifungal resistance is crucial for developing targeted therapeutic approaches. Research efforts aimed at unraveling these mechanisms are essential for identifying new drug targets and designing innovative treatment strategies to combat resistant strains. In response to the escalating threat of antifungal resistance, a multifaceted approach is required. This includes enhanced surveillance of antifungal susceptibility patterns, the development of novel antifungal agents, and the implementation of stringent guidelines for antifungal use. Additionally, educational initiatives targeting healthcare professionals and the public are essential to promote responsible antifungal use, reduce the risk of resistance emergence, and improve treatment outcomes.

This article is a continuity of prevouse two reserch in daylight harvastion control that were deigned using classical control apoproach and then fuzzy logic technique, In this article ANN controller is designed and its response is compared with the performance of the other two controllers. Detailed compression for the different error type is illustrated, however, the results show that the three controller operate with satisfactory accuracy.

Failaka Island, located in the far east of Kuwait Bay, is about 20 km from the State of Kuwait’s coast, and represents a focal point for regional geography and history, with pristine beaches and archaeological sites dating to the Bronze, Iron, Hellenistic, Christian and Islamic periods. According to environmental data and in coordination with local authorities to develop an urban plan, the island is set to become the first tourist destination for the State of Kuwait. To achieve the Vision of Kuwait 2035, one of the planning objectives focuses around Urban Planning for the Establishment of Environmental Cities that Achieve (UPEECA) environmental sustainability criteria. The paper then, aims to propose the environmental urban plan for Failaka Island. Based around Environmental Analytical Hierarchical Processes (EAHP), and using the Field Calculator and ModelBuilder functions in ArcGIS, this research centres on the feasibility of carrying out an urban plan using suitability modelling that includes four factors and 13 criteria covering the island’s ecological and human composition. This study utilizes both remote sensing (UAVs for 3D imaging) and field study (ground truthing) to identify changes in land use and land cover – such as using sample analysis of the historical sites and soils for tracing evidence and creating/updating a soil map – and create the first GIS database for the island that can lead to generating a suitability model.

This article introduces new method using ANN to control SVC in order to correct the source power factor of low voltage network. Two ANN approaches are investigated to design accurate and fast power factor correction (PFC) controller. First approach uses simple ANN (SANNA). Second approach uses cascaded ANN (CANNA). ANN regression, performance and the calculated error for both approaches are investigated to select between the two approaches. CANNA is selected as a better solution and it used to build the ANN PFFC controller using database, generated by MATLAB-Simulink, for standard three low voltage levels (240V, 220V and 110V). Nine test cases are carried out to validate the performance of proposed ANN PFC controller with a network has variable loads and low power factor (0.6 approximately). In order to extend the use of the controller to other voltage levels not included in the training process of the cascaded ANN, only the SVC is resized. Another nine cases are carried out with the same loads using the same ANN controller, as it is, to test its performance with the extended voltage level range (415V, 230V and 120V). The results show accurate and fast response in all test cases.

Background: World Health Organization (WHO) estimates that there were 558000 new cases with resistance to Rifampicin, of which 82% had multidrug-resistant tuberculosis (MDR-TB). Objectives: We aimed to identify the prevalence of MDR-TB in River Nile state, Sudan, and the risk factors contributing to its occurrence. Methods: This was a descriptive cross-sectional hospital-based study involved 200 specimens taken from patients suspected of having MDR-TB tested using an automated GeneXpert assay. Results: Results of GeneXpert assay showed that the presence of Mycobacterium tuberculosis in 81 (40.5%), and out of 81 positive test results there were 13 (16%) had MDR-TB. Additionally, 7 cases of MDR-TB were previously treated which represented about (53%) of MDR patients, the remaining 6 MDR-TB patients were new cases and represented (47%) of MDR-TB patients. Moreover, there were 4 MDR-TB patients who had a history of contact with MDR-TB patients. Conclusion: Prevalence of MDR-TB in River Nile State, Sudan was 16%, which is greater than WHO estimation for Sudan (10.1%). The results revealed that the main risk factor to develop MDR-TB was a history of contact with MDR-TB, so adherence to treatment and social awareness about the spread of MDR-TB are crucial preventive measures.

This paper presents preliminary operational performance results of a pilot grid-connected photovoltaic (PV) system designed and installed on the rooftop of the Ministry of Petroleum, Energy and Mining headquarter in Nouakchott (latitude of 18.1°N and the longitude of 16.0°W), Mauritania. The aim is for the government to demonstrate the relevance of using solar energy and to encourage the uptake of solar PV technology for commercial and residential building applications in Mauritania.. In this study, the grid-connected PV system has a peak power of 48 kW and the performance monitoring was carried out during one year, with a system that allow to measure DC power, inverter and system conversion efficiency, energy generated by the PV arrays, solar radiation in the inclination plane of panels, ambient temperature and module temperature. During this period, the PV plant was found to supply 65,668 kWh to the grid. The final yield ranged from 3.91 to 5.09 kWh/kWp/day. The performance ratio was found to vary from 69.69% to 89.35% and the annual capacity factor was found to be 19%. Finally, performance parameters were compared with other PV plants installed in the same region of Northern Africa. The outcome of this work is deemed important in assisting accurate PV system design and decision-making.

A comprehensive kinetic model of the Fischer-Tropsch synthesis (FTS) is developed in a fixed bed reactor under operating conditions (temperature, 230–235°C, pressure, 20–25 bar, gas hourly space velocity, 4000–5000 cm³(STP)/h/g_catalyst ,H₂/CO feed molar ratio, 2.1) over a Co based catalyst. Reaction rate equations based on Eley-Rideal (ER) type model for initiation step and Langmuir-Hinshelwood-Hougen-Watson (LHHW) type model for propagation and termination steps of the FTS reactions have been considered and the readsorption of olefins were taken into account. The model that was reported in the literature was modified in order to explain many significant deviations from the ASF distribution. Optimum parameters have been obtained by Genetic Algorithms (GA). The calculated activation energies to produce n-paraffins and 1-olefins were in the range of 82.24 to 90.68 kJ/mol and 100.66 to 105.24 kJ/mol, respectively. The hydrocarbon distribution in FTS reactions was satisfactorily predicted particularly for paraffins.

Abstract. This article proposes new fuzzy controller to regulation the voltage, damp the oscillations and limit the overshoot behavior in single-machine infinite-bus power system. Two different independent MISO fuzzy controllers are designed. First controller, is voltage stabilizer and it composes of two adaptive fuzzy modules and proportional gain AVR. The voltage stabilizer is designed to regulate the terminal voltage, damp the voltage oscillation and limit the voltage overshoot to the industrial maximum allowable limit. The input signals of this stabilizer is are taken from the terminal voltage and the imposed voltage disturbance that can be read from any smart relay. The fuzzy output is used as feedback signal to control the AVR in order to achieve stabilized voltage equal to the reference voltage. The second fuzzy controller is designed with two input signals; “mechanical angle” and its derivative, and one output which is used as feedback signal to adapt the damping torque in order to damp the mechanical oscillation fast and with maximum overshoot not exceeding 10%, and hence damp the power angle oscillation that is important in the PSS improvement. MATLAB-SIMULINK was used for modelling and the test cases simulation. The results show very good performance for the proposed fuzzy controllers.

This paper attempts to compare two different approaches to solve the problem of accident rates prediction based on human factors for industrial workers. One of the methods has already been done using Fuzzy c-Means Clustering and proved to be working with decent results. The second method which will be covered in this paper is using Artificial Neural Networks. The primary goal of this work is to insure that ANN will work efficiently in such prediction problem. The second goal is to reveal the fact that which one of the two selected methodologies is better at defining the estimation of accident rates among people who work in different industrial fields. The purpose has been achieved when the outcome of the ANN was obtained and compared accordingly with the output of the research previously carried out with Fuzzy c-means clustering method. Comparing the outcomes of these two different methods gave an immense insight on which features are more important than others when it comes to laborers properties with completely different background such as varying levels of health, knowledge, experience, training and physical properties. At the end of the research, it becomes clear that accident rates estimation for laborers with properly trained Artificial Neural Network gives better results when it is compared with Fuzzy c-Means Clustering method. Standard deviation method was used to calculate the validity of ANN technique. The result was compared with Fuzzy c-mean clustering technique. Impressive improvement of 8.8% in the accident rate prediction was achieved using Tailored-Made-ANN.

Global temperature rise due to hydrocarbon gases emission that are produced by generating the electrical power has a great attention by the researchers to reduce it till zero emission is successfully achieved. Sustainable energy source such as solar energy, wind, hydro-energy and sea wave energy are focal areas to replace the fossil fuel by clean energy. In this article, daylight is used to minimize the power consumption that required for indoor lighting using electric roller blind. Smart controller is designed to adjust the position of the roller blind stepper motor, and hence, adjust the roller blind opening, based on the preset light intensity, to achieve precise utilization of daylight inside the room. If the desired Lux is not achieved for any reason, the smart controller adjusts the LED circuit current to boost the light intensity to achieve precisely the desired Lux. Comprehensive test cases using MATLAB-Simulink is carried out to verify the performance of the proposed smart controller. Techno-economic analysis is introduced to evaluate the benefits of installing the controller. Summary and recommendation are given at the end.

In this paper, the problem of autonomous optimal absolute orbit keeping for a satellite mission in Low Earth Orbit using electric propulsion is considered. The main peculiarity of the approach is to support small satellite missions in which the platform is equipped with a single thruster nozzle which provides acceleration on a single direction at a time. This constraint implies that an attitude maneuver is necessary before or during each thrusting arc to direct the nozzle into the desired direction. In this context, an attitude guidance algorithm specific for the orbit maneuver has been developed. A Model Predictive Control scheme is proposed, where the attitude kinematics are coupled with the orbital dynamics in order to obtain the optimal guidance profiles in terms of satellite state, reference attitude, and thrust magnitude. The proposed control scheme is developed exploiting Formation Flying techniques where the reference orbit is that of a virtual spacecraft that the main satellite is required to rendezvous with. In addition to the controller design, the closed loop configuration is presented supported by numerical simulations. The efficacy of the proposed autonomous orbit keeping approach is shown in several application scenarios.

Chitosan decorated copper nanoparticles (CS/CuNPs) catalysts were synthesized via reduction methods utilizing green protocol. The CS/CuNPs hybrid catalysts were tested for the synthesis of quinoline derivatives utilizing one-pot multicomponent reaction (MCR) under ultrasonic irradiation. The best catalyst (CS/CuNPs) that provided good conversion reaction yield and high turnover frequency (TOF) was characterized using Fourier transform infrared (FTIR), Thermogravimetric analyses (TGA), X-ray diffraction (XRD), , scanning electron microscopy (SEM), transmission electron microscope (TEM) and X-ray photoelectron spectroscopy (XPS) techniques. Generalization of the scope of the proposed catalytic process was studied using different aldehydes. Excellent products yield and high TOF in even shorter reaction time (~5 min) was attained. Recyclability performance of the catalyst over five times re-use without detectable loss in product yield was recorded. The current method is green process utilizing environmentally benign catalyst and considered to be promising sustainable protocol for the synthesis of fine chemicals.

D-dimer testing in combination with clinical assessment is commonly used to diagnose suspected DVT and pulmonary embolism. However, as D-dimer levels are physiologically higher in elderly patients, this test loses clinical specificity in the setting of geriatric patients. The aim of our study was to investigate the changes in D-dimer levels with age and the specificity of the D-dimer test in the diagnosis of pulmonary embolism. 1617 elderly patients consecutively admitted to the Geriatric Emergency Care Department of the INRCA-IRCCS hospital between January 2013 and February 2014 and for whom D-dimer results were available were included. The D-dimer immunoturbidimetric assay was performed on a cs-2100i Sysmex Siemens using a conventional cut-off level of 500 µg/L. The median D-dimer level was 1200 [550-2990] µg/L FEU, and the percentage of patients with D-dimer levels below the conventional cut-off was only 22.1%. As expected, there was a significant age-related increase in D-dimer, even when sex was considered, and a significant decrease in the specificity of D-dimer assay with age. The most established use of D-dimer testing is in the diagnosis of deep vein thrombosis or pulmonary embolism. Our study confirms the need for an age-adjusted cut-off for D-dimer testing in geriatric patients.

This paper is an extension to previous work that introduced successful classical-control for indoor lighting system that simultaneously control LED system and roller curtain to achieve accurate light intensity for indoor lighting applications. In this paper, Multi Input Multi Output Fuzzy Logic Controller (MIMO FLC) is proposed to replace the classical-controller. Detailed method is provided to illustrate the steps to design the required MIMO FLC that has two fuzzy input, two fuzzy output and forty-five fuzzy rules with mamdani fuzzy engine. The proposed MIMO FLC is simulated in Matlab using Simulink tools. The results are illustrated, analyzed and compared with the classical-control. The response showed very close performance to the classical-controller. The maximum average error and the maximum error with respect to “Desired Lux” inside the room is -6% and -10% respectively.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

Ship detection from synthetic aperture radar (SAR) imagery is crucial for various fields in real-world applications. Numerous deep learning-based detectors have been investigated for SAR ship detection, which require a substantial amount of labeled data for training. However, SAR data annotation is time-consuming and demands specialized expertise, resulting in that deep learning-based SAR ship detectors struggle due to a lack of annotations. With limited labeled data, semi-supervised learning is a popular approach for boosting detection performance by excavating valuable information from unlabeled data. In this paper, a semi-supervised SAR ship detection network is proposed, termed as Multi-Teacher Dempster-Shafer Evidence Fusion Net-work (MTDSEFN). The MTDSEFN is an enhanced framework based on the basic teacher-student skeleton frame, comprising two branches: the Teacher Group (TG) and the Agency Teacher (AT). The TG utilizes multiple teachers to generate pseudo-labels for different augmentation versions of unlabeled samples, which are then refined to obtain high-quality pseudo-labels by using Dempster-Shafer (D-S) fusion. The AT not only serves to deliver weights of its own teacher to the TG at the end of each epoch, but also updates its own weights after each iteration, enabling the model to effectively learn rich information from unlabeled data. The combination of TG and AT guarantees both reliable pseudo-label generation and learning comprehensive diversity information from numerous unlabeled samples. Extensive experiments were performed on two public SAR ship datasets, and the results demonstrated the effectiveness and superiority of the proposed approach.

This review provides an understanding of the teaching and practising of forensic accounting across the globe. It includes a review of published forensic accounting studies that conclude that forensic accounting is of benefit to both students and professionals. Despite this, there are areas of concern; namely, the insufficiency of an appropriate structure of regulation and a lack of control over the academic qualifications to enter the profession. This review of both the teaching and practising of forensic accounting provides an overview of the vital issues and concerns that must be understood in order to advance the essential application of forensic accounting. It is expected that this review will influence future policy that will advance business and limit episodes of fraud. The amount of published literature on the subject of forensic accounting is widespread and diverse. However, there is a lack of comprehensive understanding regarding the strengths and weaknesses of forensic accounting; this review will address this and provide policymakers with a thorough explanation of the subject.

The Bcl-2 family plays a crucial role in regulating cell apoptosis, making it an attractive target for cancer therapy. In this study, a series of indole-based compounds, U1-6, were designed, synthesized, and evaluated for their anticancer activity against BCL-2-expressing cancer cell lines. The binding affinity, safety profile, cell cycle arrest, and apoptosis effects of the compounds were tested. The designed compounds exhibited potent inhibitory activity at sub-micromolar IC50 concentrations against MCF-7, MDA-MB-231, and A549 cell lines. Notably, U2 and U3 demonstrated the highest activity, particularly against MCF-7 cells. Respectively, both U2 and U3 showed potential Bcl-2 inhibition activity with IC50 values of 1.2 ± 0.02 and 11.10 ± 0.07 µM using an ELISA binding assay compared to 0.62 ± 0.01 µM for gossypol, employed as positive control. Molecular docking analysis suggested stable interactions of compound U2 at the Bcl-2 binding site through hydrogen bonding, pi-pi stacking, and hydrophobic interactions. Furthermore, U2 demonstrated significant induction of apoptosis and cell cycle arrest at G1/S phase. Importantly, U2 displayed a favorable safety profile on HDF human dermal normal fibroblast cells at 10-fold greater IC50 compared to MDA-MB-231 cells. These findings underscore the therapeutic potential of compound U2 as a Bcl-2 inhibitor and provide insights into its molecular mechanisms of action.

The nuclear hormone family of receptors regulates gene expression. The androgen receptor (AR) shuttles upon ligand binding and homodimerization from the cytosol into the nucleus to activate gene expression. Thyroid hormone receptors(TR), retinoic acid receptors (RAR), and the vitamin D receptor (VDR) are present in the nucleus bound to chromatin as a heterodimer with the retinoid X receptors (RXR) and repress gene expression. Ligand binding leads to transcription activation. The hormonal ligands for these receptors play crucial roles to ensure the proper conduct of very many tissues and exert effects on prostate cancer (PCa) cells. Androgens support PCa proliferation and deprivation alone or with chemotherapy is the standard therapy for PCa. RAR activation and 3,5,3'-triiodo-L-thyronine (T3) stimulation of TR support the growth of PCa cells. Ligand stimulation of VDR drives growth arrest, differentiation, and apoptosis of PCa cells. Often these receptors are explored as separate avenues to find treatments for PCa and other cancers. However, there is accumulating evidence to support receptor interactions and crosstalk of regulatory events whereby a better understanding might lead to new combinatorial treatments.

This study aims to theoretically address the design and analysis of an efficient pressure sensor designed by using a polymer-based defective 1D annular photonic crystal (APC). The 1D APC comprises an alternate arrangement of Si and SiO2 in a cylindrical fashion, incorporating a central defect layer. The investigation of the reflectance characteristics of the proposed structure is conducted by separately considering the polystyrene (PS) and the polymethyl methacrylate (PMMA) polymer materials as the defect layer. The pressure-sensitive refractive index of the polymers and the constituent materials of the APC plays a vital role in envisaging the pressure-sensing application. The cornerstone of this study is represented by the shift analysis in the wavelength of the defect mode inside the band gap using different applied pressures by employing the modified transfer matrix method (MTMM). Various geometrical parameters like the defect polymer layer’s thickness and the APC period were carefully optimized to achieve higher sensing performance. The proposed design demonstrated a remarkable pressure sensitivity and FoM of 51.29 nm/GPa and 301.7 GPa-1, respectively, which is considerably high in the current research scenario. It is believed that the proposed structure can be an apt candidate as an innovative high-performance pressure sensor, and it can play a key role in photonic integrated circuits.

This is a single tertiary center in southwest Romania, population-based, study. We retrospectively compared data obtained in two periods: January 2008 - December 2013 and January 2018 - De-cember 2023, respectively. The global incidence of transposition of great arteries (TGA) - the ter-minated cases added to the ones resulting in live-born pregnancies, remained almost constant. The live-born incidence of TGA decreased (0.34% to 0.013%). The prenatal detection rate increased slightly (71.42% to 87.5%). The median gestational age at the diagnosis decreased, from 29.3 ges-tational weeks (mean 25.4) to 13.4 weeks (mean 17.2). The proportion of terminated pregnancies significantly increased (14.28% to 75%, p = 0.019).

This research aims to apply Artificial Intelligence (AI) methods, specifically Artificial Immune Systems (AIS), to design an optimal control strategy for a multivariable control plant. Two specific industrial control approaches are investigated: I-PD (Integral-Proportional Derivative) and PI-D (Proportional-Integral Derivative) control. The motivation for using these variations of PID controllers is that they are functionally implemented in modern industrial controllers, where they provide precise process control. The research results in a novel solution to the control synthesis problem for the industrial system. In particular, the research deals with the synthesis of I-P control for a two-loop system in the technological process of a distillation column. This synthesis is carried out using the AIS algorithm, which is the first application of this technique in this specific context. Methodological approaches are proposed to improve the performance of industrial multivariable control systems by effectively using optimization algorithms and establishing modified quality criteria. The numerical performance index ISE justifies the effectiveness of the AIS-based controllers in comparison with conventional PID controllers (ISE₁ = 1.865, ISE₂ = 1.56). The problem of synthesis of the multi-input multi-output (MIMO) control system is solved, considering the interconnections due to the decoupling procedure.

This paper discusses domestic problem of waiting hot water for the shower use till it reaches satisfactory temperature, which result a lot of wastage in fresh water. The outcome from research survey shows that there is no satisfactory solution till now as all solutions were either expensive or with no effective results. Local small inline electric heater equipped with fuzzy logic controller is proposed in this paper to be installed just before the showerhead to measure the water temperature and flow before the showerhead, as control input-variables, and decide the operating voltage of the heater, as control output-variable (MISO). MATLAB Simulink is used to model the proposed system. Different test cases are simulated to prove the performance and the safe operation of the system. Techno-economic study is carried out to determine the “Direct Benefits” and “Indirect Benefits” that can be achieved if such system is implemented in wide range. Azerbaijan data is taken as an example to calculate the economic benefits. The results show important benefits not only for economy but also for climate and the reduction of CO₂ gas emission. Different economic indices are provided to be an easy reference for decision makers and project managers.

Deep sky observation is a fascinating activity, but it requires favourable conditions in order to be fully appreciated. Complex equipment, light pollution around urban areas, lack of contextual information often prevents newcomers from making the most of their observations, restricting the field to a niche expert audience. In this paper, we show how combining the usage of smart telescopes with eXplainable Artificial Intelligence makes the practice of astronomy even more accessible and educative, and how it has been applied during outreach sessions In Luxembourg Greater Region.

In recent years, the implementation of artificial intelligence (AI) in accounting has grown in many domains, including auditing. AI permits auditors to evaluate large data sets and rapidly identify discrepancies and sequences in audit. This means auditors can review all of a client's transactions via a low time and effort. This entails auditing firms investing heavily in technological infrastructure as well as training their human resources to use cutting-edge AI technologies. Thus, this research sought to investigate the impact of the use of AI techniques by Jordanian external auditors in fraud risk assessment, the moderating effect of auditor size. The descriptive analytical method was used by distributing 280 questionnaires electronically to auditors employed in auditing firms operating in Jordan, The result reveals that AI techniques are extremely beneficial in fraud risk assessment at all levels, and the relationship between the use of AI techniques and the assessment of fraud risk has improved as auditor size has increased.

The concept of this prototype is to create a cold air film layer, in indoor side of the window. The function of this extra cold air layer is to increase the amount of window resistance and decrease its U-Value. It provide air film layer by using the same concept of desert cooler or wind catcher. They both bring the hot air from outside then let it go throw straw miost with cold water. After hot air move through straw, it would become cold, thus increase the window resistance and decrease the haet gian, therefore, decrease the cooling load. So, this window model works by heating the air in air room by sun radiation, then after a while, air pressure will rise and its volume will increase then it will impulse to wet hay, and become cold. Then there is fins to guide air flow to its correct direction, thus inner side of window will become cold, not like other type of window which when temperature rise, the inner side of window become hot. So, this window prevents heat transition and creare regenereted trubouland air flim in the inner side of the window. Using calculation to find air film characteristics and WINDOW7.7 software to calculate heat gain through window, shows that it is expected from this prototype to reduce heat gain by 6.85 % for double glazed clear window.

Recent studies have demonstrated a relationship between poor vitamin D status and respiratory infections and diarrhea among young children. Acute lower respiratory infections (ALRI) and diarrhea are among the two most important causes of death in under-5 children. In this analysis, we examine the extent to which vitamin-D deficiency (<10 ng/ml) predicts these outcomes using data from a randomized controlled trial (RCT) of daily folic acid and/ or vitamin B12 supplementation for six months in 6 to 30 months old children conducted in Delhi, India. Of the 960 subjects who had vitamin-D concentrations measured, 331(34.5%) were vitamin-D deficient. We found, after controlling for relevant potential confounders (age, sex, breastfeeding status, wasting, stunting, underweight, anemia status at base line and season), the risk of ALRI was significantly higher among vitamin-D deficient (OR 1.26; 95% CI: 1.03 to 1.55) compared to vitamin-D-replete children in the six months follow-up period. Vitamin-D status was not significantly associated with episodes of diarrhea and clinical pneumonia. The extent of causal relationship of vitamin-D status and ALRI needs to be explored in further studies.

Although vitamin D deficiency has been correlated with an increased risk of cardiovascular disease (CVD), there are few data on the association between 25-hydroxyvitamin D (25(OH) D) and atherogenic indices predictive of CVD. This study aimed to investigate the relationship of vitamin D status with lipid profile and atherogenic indices in adult women in Morocco. Three hundred healthy women, aged 18 to 50 years, from Meknes were included. Fasting 25(OH) D and lipid concentrations were determined using a one-step electrochemiluminescence-based immunoassay and an enzymatic method, respectively. Atherogenic indices (Atherogenic index of plasma (AIP), non-HDL cholesterol (Non-HDL-C), Atherogenic coefficient (AC), Castelli risk indices I and II (CRI-I and II), and CHOLIndex (CI)) were calculated using conventional lipid parameters. Logistic regression models and operating characteristic curve (ROC) analysis were used to assess the relationship of the variables and estimate the threshold of 25(OH) D levels associated with high atherogenic indices. 25(OH) D below 20 ng/ml was significantly associated with an enhanced risk of hypertriglyceridemia and elevated values of AIP, AC, Non-HDL-C, and CRI-I with an OR (95% CI) of 4.904 (1.856-12.959); 3.637(2.149-6.158); 3.589(1.673-7.700); 2.074(1.215-3.540), and 2.481(1.481-4.123), respectively. According to ROC analysis, the likelihood of hypertriglyceridemia and high values of AIP, AC, Non-HDL-C, and CRI-I were associated with 25(OH)D thresholds ≤15.15 ng/ml, ≤ 17.5 ng/ml, ≤ 19.8 ng/ml, ≤ 20.1 ng/ml and ≤ 19.5 ng/ml, respectively, all p &lt; 0.01. Based on atherogenic indices, this study indicates that vitamin D below 20 ng/ml may increase the risk of cardiovascular disease in adult women. Additional health efforts are needed to raise awareness among women and healthcare providers in preventing and controlling cardiovascular risk factors.

This article discuss the estimation of electrical stresses input that is required to determine lifetime degradation of the HV cables installed within overhead transmission lines (OHTL’s). Abort from lightning effects, these electrical stresses are mainly generated due to repetitive switching operation of the transmission line that produces transient overvoltage (TOV) stress and high frequency stress. The transient overvoltage (TOV) due to switching-off the transmission line at the interface points between the cable and OHTL is estimated using artificial neural network (ANN). PSCAD software is used to build the transmission line model for 749 different case in order to build the required database for ANN training. Two different algorithm input to train ANN with one hidden layer and one output layer using different number of nodes are modeled in MATLAB. The results performance is continuously compared and evaluated till acceptable Regression is achieved to insure the error is less than +/-1.5%. The high frequency due to switching-on the transmission line is also recorded and analyzed. The results show that this new method is efficient, accurate and useful as there is no cable monitoring system is available for each HV cable installed within the transmission line.

This paper proposes a novel deterministic methodology for estimating the optimal sampling frequency (SF) of water quality monitoring systems. The proposed methodology is based on employing two-dimensional contaminant transport simulation models to determine the minimum SF considering all the potential changes in the boundary conditions of a water body. A two-dimensional contaminant transport simulation model (RMA4) was implemented to estimate the distribution patterns of the total dissolved solids (TDS) within the Al-Hammar Marsh in the southern part of Iraq for 30 cases of potential boundary conditions. Using geographical information system (GIS) tools, a spatiotemporal analysis approach was applied to the results of the RMA4 model to determine the minimum SF of the monitoring stations with an accuracy level of detectable change in TDS concentration (ALC) of 5%, 10% and 15%. The proposed methodology specified a minimum and maximum SF for each monitoring station (MS) that ranged between 12 and 33 times per year, respectively. Additionally, increasing the ALC to 10% and 15% increase the minimum SF for some MSs by approximately 18% and 21%, respectively. However, the proposed methodology includes all the potential values and cases of boundary conditions, which increases the certainty of monitoring the system and the efficiency of the SF schedule. Moreover, the proposed methodology can be effectively applied to all types of surface water resources.

This paper aims to provide an adaptation of the TL-moments method to censored data. The present study concentrates on Type-I censored data. The idea of using TL-moments with censored data may seem conflicting. But our perspective in that, we may use data censored from one side and trimmed from the other side. This study is applied to estimate the two unknown parameters of the Weibull distribution. The suggested point is compared with Direct L-moments and ML methods. A Monte Carlo simulation study is carried out to compare these method in terms of estimate average, root of mean square error (RMSE) and relative absolute biases (RAB).

A milk drink flavored with dates syrup produced at a lab scale level was evaluated. The production process of date syrup involves a sequence of essential unit operations, commencing with the extraction, filtration, and concentration processes from two cultivars: Sukkary and Khlass. Date syrup was then mixed with cow’s and camel’s milk at four percentages to form a nutritious, natural, sweet, and energy milk drink. Sensory, physical, and chemical characteristics of the milk drinks flavored with date syrup were examined. The objective of this work was to measure physiochemical properties of dates fruits and milk drinks flavored with dates syrup, then to evaluate the physical properties of milk drinks utilizing a non-destructive NIR spectra. The study assessed the characteristics of the milk drink enhanced with date syrup by employing near-infrared spectra (NIR) spectra and analyzed utilizing partial least-square regression (PLSR) and artificial neural network (ANN) analysis. The NIR spectrum proved to be highly effective in estimating the physiochemical attributes of the flavored milk drink. The ANN model outperformed the PLSR model in this context. RMSECV is considered a more reliable indicator of a model's future predictive performance compared to RMSEC, R2 ranged between 0.946 and 0.989. Consequently, non-destructive NIR technology demonstrates significant promise for accurately predicting and contributing to the entire production process of the product's properties examined.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

There is a need to develop enriched milk drinks with healthy and natural additives. A consumer test was conducted to compare milk (cow and camel) flavored with date syrup (Khlass and Sukkary varieties) at different percentage. The objective of the present work was to study consumers liking patterns for flavored milk drinks from dates syrup (from Khlass and Sukkary dates), at different percentages, added to milk (cow and camel) utilizing preference mapping analysis. A total of sixteen trained panelists took part in the test. The obtained data were used to develop an internal preference map for these samples. Principal component analysis (PCA) and Agglomerative hierarchical clustering (AHC) algorithms were used to construct the preference map. The first component signifies overall acceptance of taste and color, while the second focuses on texture and flavor. Consumers were grouped into five clusters based on preferences. Cluster two favored both components positively, while cluster four leaned negatively on both. A factorial ANOVA was performed and the results showed a significant effect of the main factors as well as the interactions. Panelists preferred cow's milk over Camel’s milk in all aspects. For taste, cow’s milk with 20% Khlass syrup or 10% Sukkary syrup was favored, while in flavor, it was cow’s milk with 5% Khlass syrup and Camel’s milk with 10% Sukkary syrup. Texture-wise, Camel’s milk with 5% Khlass syrup and 15% Sukkary syrup, along with cow’s milk with 10% Khlass syrup, received top marks. In color evaluation, cow’s milk with 15% Sukkary syrup was the preferred choice. Finally, for overall color score, cow’s milk with 10% Sukkary syrup led, followed by cow’s milk with 5% Sukkary syrup. This research suggests that dairy companies may have more impact if they use date syrup as a natural and healthy flavor. The preference map includes two main dimensions; the first represents overall acceptance, taste, and color while the second is related to flavor and texture attributes. The preference map can be used in product optimization and development.

This paper aims to demonstrate that, beyond the small world of Riemann-Liouville and Caputo derivatives, there is a vast and rich world with many derivatives suitable for specific problems and various theoretical frameworks to develop, corresponding to the different paths taken. Notions of time and scale sequences are introduced and general associated basic derivatives, namely right/stretching and left/shrinking, are defined. A general framework for fractional derivative definitions is reviewed and applied to get both known and new fractional order derivatives. Several fractional derivatives are considered, mainly: Liouville, Hadamard, Euler, bilinear, tempered, q-derivative, and Hahn.

The purpose of this paper is to explore the impact on corporate social responsibility when Jordanian banks disclose risks. The main objective of the study is to investigate the relationship between risk disclosure and corporate social responsibility in the banking sector in Jordan. To achieve this goal, data was collected from 23 Jordanian banks listed on the Amman Stock Exchange (ASE) over a period of 10 years, from 2010 to 2019. The data was analyzed using a regression model with four independent variables that represent the risk disclosure; corporate social responsibility was used as the dependent variable. The study also built in controls for the age of each bank, its size, leverage, and ROE, to ensure that the results were not affected by these factors. The results of the study show that all independent variables are positively correlated with corporate social responsibility. This suggests that disclosing risks is an effective way to improve corporate social responsibility in the banking industry. The findings of this study have important practical implications for bank managers, future researchers, and policymakers. The study also highlights the importance of future research in this field in order to understand the relationship between risk disclosure and corporate social responsibility in other countries and within other sectors of industry.

Counter-current spontaneous imbibition of water is a critical oil-recovery mechanism. In the laboratory, the Amott test is a widely used technique to assess efficacy of brine imbibition into oil-saturated core plugs. The classic Amott-cell methodology was designed to estimate ultimate oil recovery, but not the recovery dynamics that provides essential information about the imbibition mechanisms. Retention of oil droplets at the external core surface and delayed onset of oil production are the two key artifacts of the classic Amott experiment. This retention, referred to here as the ``external-surface oil holdup effect'', often results in stepwise recovery curves that obscure true dynamics of spontaneous imbibition. To address these holdup drawbacks of the classic Amott method, we modified the Amott cell and experimental procedure. For the first time, using water-wet Indiana limestone cores saturated with brine and mineral oil, we showed that our improvements of the Amott method enabled accurate and reproducible measurements of oil-recovery dynamics. We used the Generalized Extreme Value (GEV) statistics to describe oil-production histories from water-wet heterogeneous limestone cores with finite initial water saturations, for the first time. We demonstrated that our four-parameter GEV model accurately described the recovery dynamics, and that optimal GEV parameter values systematically reflected the key characteristics of the oil-rock system, such as oil viscosity and rock permeability. These findings gave us a more fundamental understanding of spontaneous, counter-current imbibition mechanisms and insights into what constitutes a predictive model of counter-current water imbibition into oil-saturated rocks with finite initial water saturation.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

Alcoholic liver disease (ALD) develops when the immunotolerant environment of the liver is compromised due to excessive alcohol consumption. ALD progression involves variations in the expression of multiple genes, resulting in liver inflammation and the development of a leaky gut. Molecular mechanism involved for ALD progression is still unclear, and due to that there are currently no FDA-approved drugs available for its treatment. In this study, the protective effects of Graphene oxide nanoparticles (GO) was investigated against ethanol-induced damage in the gut-liver axis in in vitro. GO was synthesized using a modified Hummer's method and characterization was done. Given the general concerns regarding nanoparticle toxicity, assessment of cell viability, lipid accumulation, DNA damage, cell death, and the generation of reactive oxygen species (ROS) were conducted using various techniques. Furthermore, gene expression of pro- and anti-inflammatory cytokines was done using RT-qPCR. The findings revealed that GOs promoted cell viability even against ethanol treatment. Additionally, lipid accumulation significantly decreased when cells were treated with GO alongside ethanol compared to ethanol treatment alone, with similar trends observed for other assays. Gene expression analysis indicated that GO treatment reduced the expression of proinflammatory cytokines while enhancing the expression of antioxidant genes. Moreover, GO treatment led to improvements in gut permeability and a reduction in proinflammatory cytokines in colon cells damaged by ethanol. These findings suggest that GO holds promise as a drug carrier, exhibiting no observed toxic effects. By shedding light on the protective effects of GO against ethanol-induced damage, this study contributes to the burgeoning field of nanoparticle-mediated therapy for ALD.

Hashimoto's thyroiditis (HT) is essentially featured by self-tissue destruction by means of the adaptive immune responses that evade immune regulation. Vitamin D carries out an immunomodulatory role that appears to promote immune tolerance. The aim of this study is to elaborate a narrative review about the relationship between vitamin D status and HT and the role of vitamin D supplementation to reduce HT risk by modulating the immune system. There is an extensive literature confirming that vitamin D levels are significantly lower in HT patients compared to healthy people. On the other hand, after the supplementation with cholecalciferol in patients with HT and vitamin D deficiency, thyroid autoantibody titer decreased significantly, However, there are no conclusive results on the effect of vitamin D supplementation on the thyroid function. The confirmation of the beneficial effects of vitamin D in the prevention and treatment of autoimmune thyroid diseases require additional randomized, double-blind, placebo-controlled trials with longer follow-up.

Phytochemicals have a long and successful history in drug discovery. With recent advancements in analytical techniques and methodologies, discovering bioactive leads from natural compounds has become easier. Computational techniques like molecular docking, QSAR modelling and machine learning, and network pharmacology are among the most promising new tools that allow researchers to make predictions concerning natural products' potential targets, thereby guiding experimental validation efforts. Additionally, approaches like LC-MS or LC-NMR speed up compound identification by streamlining analytical processes. Integrating structural and computational biology aids in lead identification, thus providing invaluable information to understand how phytochemicals interact with potential targets in the body. Emerging computational approach is machine learning involving QSAR modelling and deep neural networks that interrelate phytochemical properties with diverse physiological activities such as antimicrobial or anticancer effects.

Article explores participant specific study of muscle inherehit dynamics hidden inside the diognostic electromyography (D-EMG) signals during load pull exercises, aiming to uncover underlying patterns and nonlinear behaviors. Employing a multi-step analytical framework, the study first evaluates signal stationarity through Quantile-Quantile (Q-Q) plot and surrogate data analyses, revealing insights into signal stability. Subsequent use of phase space reconstruction techniques exposes intrinsic dynamics within the EMG signals, visualized through Poincar´e maps, elucidating attractor geometry and system dynamics. Histogram analysis further dissects the Poincar´e maps, offering insights into signal behavior relative to physiological processes. Additionally, the study quantifies the largest Lyapunov exponent from the Poincar´e maps, providing a measure of dynamical complexity within the muscle EMG signals during load pull exercises. By integrating these methods, this research sheds light on the nuanced interplay between EMG signals and muscle activity during dynamic exercises, offering valuable insights for rehabilitation strategies.

The present paper presents findings from the follow-up of 185 of these nurses who had been involved in the front-line care of COVID-19 patients in urban centres in Northern England, during and after the “second wave” of COVID patients in November, 2020. Measures of adjustment, stress (including PTSD), and Maslowian self-actualization were added to earlier measures of personality, adjustment, work-life stress, and career intention. Cluster analysis identified three types in the 2020-2023 cohort: I ‘Actualizing Professionals’; (N=62); II ‘Strong Professionals’ (N=56); III ‘Highly Stressed Nurses’ (N=45). These latter very stressed nurses included all nurses (N=16) identified as having PTSD symptoms.

Chronic kidney disease (CKD) and cardiovascular disease (CVD) are highly prevalent conditions, each significantly contributing to the global burden of morbidity and mortality. CVD and CKD share a great number of common risk factor, such as hypertension, diabetes, obesity, and smoking among others. Their relationship extends beyond these factors, encompassing intricate interplay between the two systems. Within this complex network of pathophysiological processes, vitamin D has emerged as a potential linchpin, exerting influence over diverse physiological pathways implicated in both CKD and CVD. In recent years, scientific exploration has unveiled a close connection between these two prevalent conditions and vitamin D, a crucial hormone traditionally recognized for its role in bone health. This article aims to provide an extensive review of vitamin D's multifaceted and expanding actions concerning its involvement in CKD and CVD.

This initial report of a longitudinal study of 192 English hospital nurses has measured Nursing Values (the 6Cs of nursing); Personality, Self-Esteem and Depression; Burnout Potential; Work-Life Balance Stress; ‘Hardy Personality’; and Intention to Leave Nursing. Correlational, component and cluster analysis identifies four groups: “The Soldiers” (N = 79) , with medium scores on most measures, who bravely ‘soldier on’ in their nursing roles, in the face of numerous financial cuts to the National Health Service, and worsening nurse-patient ratios; “Cheerful Professionals” (N = 54), coping successfully with nursing roles, and a variety of challenges, in upwardly mobile careers; “High Achievers” (N = 39), senior nurses with strong profiles of a ‘hardy personality’, and commitment to fundamental nursing values; “Highly Stressed, Potential Leavers” (N = 20), with indicators of significant psychological distress, and difficulty in coping with nursing role challenges. We propose a model of co-counselling and social support for this distressed group, by nurses who are coping more successfully with multiple challenges. We discuss the role of nurse educators in fostering nursing values, and developing and supporting ‘hardy personality’ and emotional resilience in recruits to nursing. This study is framed within the disciplinary approach of Critical Realism, which identifies the value basis for research and dialogue in developing strategies for social change.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

African indigenous herbs and medicinal plants are extensively reported for their protective and therapeutic potential against Diabetes. However, most of the constituent phytochemicals that may account for the therapeutic activity are largely uninvestigated. Exploring novel phytochemical–target interactions in silico could help to provide useful insights into the mechanism underpinning the biological activities of these plants and their constituent phytochemicals. The aim of this study was to explore the interactions of terpene struc-tures previously reported from selected African antidiabetic with two emerging drug targets in diabetes. Structure-based virtual screening was used to screen 107 terpene structures against DPP-4 and PTP1B enzymes. The MD simulation, MM-GBSA free energy calculation and DFT were used to clarify the inter-actions of the in silico hits with the target enzymes. Molecular docking, post-docking Prime MM-GBSA analysis revealed the top terpenes with high binding affinity with the active site regions of DPP-4 and PTP1B. Ensemble docking revealed three triterpenes viz: cucurbitacin B (T1), 6-Oxoisoiguesterin (T4) and 20-Epi-isoiguesterinol (T2) as in silico hits which exhibit strong interaction potential with critical residues that define the catalytic triad (Ser630 and His740); oxyanion cavity (Ser631); hydrophobic S1 pocket (Tyr662) and the charged S2 pocket (Arg125) in the active site region of DPP-4. The interactions of these compounds with DPP-4 exhibited structural stability and conformational flexibility during 100 ns full atomistic MD simulation as indicated by the structure dynamics parameters including RMSD, RoG, SASA and hydrogen bond number. The post-MD MM/GBSA calculations further revealed the stability of the triterpene-DPP-4 complexes. Furthermore, Frontier molecular orbital calculations showed that, the triterpenes possess high interaction potential with the enzyme. The triterpenes showed desirable ADMET properties and drug-likeness. Therefore, cucurbitacin B, 6-Oxoisoiguesterin and 20-Epi-isoiguesterinol are recommended for experimental validation.

OPMDs (Oral Potentially Malignant Disorders) are a group of disorders affecting the oral mucosa that are characterized by aberrant cell proliferation and a higher risk of malignant transformation. Vitamin D (VitD) and its receptor (VDR) have been extensively studied for their potential contributions to the prevention and therapeutic management of a range of diseases and neoplastic conditions, including oral cancer. Observational studies suggest correlations between VitD deficiency and higher cancer risk, worse prognosis, and increased mortality rates. Interestingly, emerging data also reveals a link between VitD insufficiency and the onset or progression of OPMDs. Understanding the role of the VitD-VDR axis not only in established oral tumors but also in OPMDs might thus enable early detection and prevention of malignant transformation. With this article, we want to provide an overview of current knowledge about OPMDs and VitD, and investigate their potential association and ramifications for clinical management of OPMDs.

In the present work we revise and extend the Characteristic Crystallographic Element (CCE) norm, an algorithm used to simultaneously detect radial and orientational similarity of computer-generated structures with respect to specific reference crystals and local symmetries. Based on the identification of point group symmetry elements, the CCE descriptor is able to gauge local structure with high precision and finely distinguish between competing morphologies. As test cases we use computer-generated monomeric and polymer systems of spherical particles interacting with the hard-sphere and square-well attractive potentials. We demonstrate that the CCE norm is able to detect and differentiate, between others, among: hexagonal close packed (HCP), face centered cubic (FCC), hexagonal (HEX) and body centered cubic (BCC) crystals as well as non-crystallographic fivefold (FIV) local symmetry in bulk 3-D systems; triangular (TRI), square (SQU) and honeycomb (HON) crystals, as well as pentagonal (PEN) local symmetry in thin films of one-layer thickness (2-D systems). The descriptor is general and can be applied to identify the symmetry elements of any point group for arbitrary atomic or particulate system in two or three dimensions, in the bulk or under confinement.

Fire hazards present a multifaceted global challenge that endangers human lives and environmental safety. Despite advancements in fire risk management technologies and methods, fires continue to be a prime concern for human security. The Arabian Gulf region, influenced by its climatic and environmental conditions, is especially susceptible to these threats. The Emirate of Sharjah, part of the United Arab Emirates, has made significant progress in reinforcing fire safety measures within residential structures, achieving a decrease in the number of fire-related accidents compared to neighboring Emirates. However, the incidence rate remains relatively high. This study undertook a thorough review and assessment of the existing Fire Management System (FMS) for Sharjah's residential sector, leading to the recommendation of a more robust framework. Through a series of literature reviews, interviews with stakeholders, and surveys, using analytical techniques such as the Delphi method and Failure Mode Effect and Criticality Analysis, vital factors that influence the FMS's effectiveness were pinpointed. The study exposed that the current FMS was largely reactive. In response, a proactive framework incorporating nine essential components was designed to strengthen the Sharjah FMS. These components span across various domains such as fire assurance, assessment of fire risks, management of accidents, evaluation of performance, training programs, research and development initiatives, digital services, monitoring of regulatory compliance, firefighting strategies, automated responses to fires, recovery processes, as well as the use of resilient materials and architectural design considerations. Furthermore, the research introduced two specific fire indexes, the HRBFI and the EFRI. Anchored in the principles of Systems Thinking and Industry 4.0, this proposed framework is aimed at streamlining Sharjah's approach to fire management in dwellings, with the objective of diminishing the frequency of fire incidents yearly. The ultimate aspiration of this framework is to enhance the Emirate's standing in terms of safety and to guarantee a living environment that is safeguarded against the risk of fires..

The Dubai Digital Government launched its recent guidelines, which call for artificial intelligence systems to be subject to legal accountability. This study discusses the extent to which autonomous robots can be granted legal personality in UAE law and the consistency of this approach with the provisions of Islamic jurisprudence. This research paper answered two main questions: First, the extent to which these guidelines are considered the beginning of work on granting legal personality to AI systems in the UAE. Second, what form of legal personality can be given to autonomous robots in UAE law to be consistent with the provisions of Islamic jurisprudence as a primary source of legislation in the country? The research concluded the impossibility of considering autonomous robots as a "thing" and classifying them within the concept of "persons." It also concluded that it is possible to give them legal personality according to two legislative solutions: granting them partial or incomplete performance eligibility like minors.

Electronic text stylometry is a collection of forensics methods that analyze the writing styles of input electronic texts in order to extract information about authors of the input electronic texts. Such extracted information could be the identity of the authors, or aspects of the authors, such as their gender, age group, ethnicity, etc. This survey paper presents the following contributions: 1) A description of all stylometry problems in probability terms, under a unified notation. To the best of our knowledge, this is the most comprehensive definition to date. 2) A survey of key methods, with a particular attention to data representation (or feature extraction) methods. 3) An evaluation of 23,760 feature extraction methods, which is the most comprehensive evaluation of feature extraction methods in the literature of stylometry to date. The importance of this evaluation is two fold. First, identifying the relative effectiveness of the features (since, currently, many are not evaluated jointly; e.g. syntactic n-grams are not evaluated against k-skip n-grams, and so forth). Second, thanks to our generalizations, we could evaluate novel grams, such as what we name compound grams. 4) The release of our associated Python feature extraction library, namely Fextractor. Essentially, the library generalizes all existing n-gram based feature extraction methods under the "at least l-frequent, dir-directed, k-skipped n-grams'', and allows grams to be diversely defined, including definitions that are based on high-level grammatical aspects, such as POS tags, as well as lower-level ones, such as distribution of function words, word shapes, etc. This makes the library, by far, the most extensive in this domain to date. 5) The construction, evaluation, and release of the first dataset for Emirati social media text. This evaluation represents the first evaluation of author identification against Emirati social media texts. Interestingly, we find that, when using our models and feature extraction library (Fextractor), authors could be identified significantly more accurately than what is reported with similarly sized datasets. The dataset also contains sub-datasets that represent other languages (Dutch, English, Greek and Spanish), and our findings are consistent across them.

This study examines the relationship between firm-level and macroeconomic variables and stock prices (SP) in Iran, Saudi Arabia (KSA), and Iraq, where economic conditions are uncertain. The sample consists of all firms listed on these countries' stock exchanges between 2015 and 2019, yielding a comprehensive dataset from 154 Iranian firms, 82 KSA firms, and 33 Iraqi firms. Using a fixed effect model, intriguing relationships are uncovered between firm-level and macroeconomic factors on SP. The findings indicate that, at a 1% significance level, there is a strong link between Iran and Iraq's GDP and their respective SP. In KSA, the association between GDP and SP is positive and significant at a 5% level. In addition, there is a positive and statistically significant correlation between the inflation rate and SP in all three countries. Moreover, the association between exchange rates and SP is significant and positive in KSA and Iraq but negative and significant at the 1% significance level in Iran. Furthermore, in KSA, the connection between oil prices and SP is positive and significant, whereas, in Iran, the relationship is negative at the 1% level. Surprisingly, there is no association between the price of oil and Iraqi SP. Regarding intangible assets, their impact on SP in Iran and KSA is negligible. In Iraq, however, there is a negative and significant relationship at the 5% level, indicating that intangible assets have a detrimental impact on SP. These findings highlight the complex link among macroeconomic factors, intangible assets, and SP in the examined countries. Policymakers and governments should prioritize implementing measures to foster sustainable economic growth, manage inflation, and stabilize exchange rates. These actions can boost investor confidence and contribute to the stock market's overall development.

The SARS-CoV-2 have caused a devastating pandemic of all times in the recent human history. However, there is a serious paucity in high quality data on aggravating factors and mechanisms of co-infection. This study aimed to identify the trending patterns of bacterial co-infections and types and associated outcomes in three phases of the pandemic. Using quality hospital data, we have investigated the SARS-CoV-2 fatality rates, profiles, and types of bacterial co-infections before, during, and after COVID-19 vaccinations. Out of 389 isolates used in different aspects, 298 was examined before and during the pandemic (n=149 before, n=149 during), death rates were 32% during compared to only 7.4% before pandemic with significant association (P value = 0.000000075). Death rate was 34% in co-infected (n = 170) compared to non-co-infected patients (n = 128) indicating a highly significant value (P value = 0.00000000000088). However, analysis of patients without other respiratory problems (n=28) indicated that among the remaining 270 patients, death was 30% in co-infected patients (n=150) and only 0.8% in non-coinfected (n=120) with high significant P value= 0.00000000076. The trending patterns of co-infections before, during, and after vaccinations showed a significant decline in Staphylococcus aureus with concomitant peaks in Gram-negatives in totals of (n= 149 before/n= 149 during): Klebsiella pneumonia (n = 11/49 before/during; E. coli n=10/24, A. baumannii n=8/25, and Ps. Aeruginosa n= 5/16, and S. aureus 13/1. Nevertheless, in post vaccination phase, (n= 91) gender-specific co-infections were examined for potential differences in susceptibility. Methicillin resistant S. aureus (MRSA) dominated both genders followed by E. coli in males and females with the latter gender showing higher rates of isolations in both species. Klebsiella pneumoniae declined to third place mostly in male patients. The drastic decline in K. pneumoniae and Gram-negatives post-vaccination strongly imply a potential co-protection in vaccines. Future analysis would gain more insights into molecular mimicry.

Background: Nutritional rickets is still considered as a global health problem especially in low-resource countries and immigrant societies of developed countries. Generalized skeletal deformities including angular knee deformities as genu varum and genu valgum are prominent features of nutritional rickets. Angular knee deformities can cause gait difficulties. However, the true remodelling potential of the healed knee deformities is largely unknown to the pediatric and orthopedic community. Aims: The primary objective of this study protocol is to investigate the natural history of disease in regard to the remodelling potential of angular knee deformities in children and adolescents with healed nutritional rickets. And determine the potential patient- and deformity-related factors that are associated with a favorable deformity remodelling as age and sex of patients and type, severity, laterality of deformities etc. Methods: This will be a prospective observational analytical cohort natural history of disease study. A minimum of at least 140 knees with healed nutritional rickets and angular knee deformities will be observed at regular three-monthly intervals over a period of at least one year. We will report two outcome variables namely; clinical and radiological tibio-femoral angle. And independent patient and deformity-related variables as age, sex, deformity type, severity and laterality. Inferential statistics namely bivariate and multivariate analysis will be employed accordingly to identify the relation between outcome variables and the different independent variables. Ethics and dissemination: This protocol study has been approved by the institutional research ethics committee. Results will be presented at conferences and submitted to relevant international and society publications. Authors will also communicate the results to their scholarly networks and post them on scholarly networking sites. Conclusions: This study has the potential for improving the decision-making process as to which patients deserve conservative treatment and which deserve surgical deformity correction. Results are expected to have an impact on the clinical practice of pediatricians, orthopedic surgeons and family physicians alike.

The most recent National Research Council Nutrient Requirements for Sheep and Goats was published in 2007, one of the most consequential nutrient requirement recommendations for sheep and goats in the world. It is pertinent to continue the refinement and discussion of nutrient utilization and requirements for the purposes of enhancing the efficiency of production systems, maximizing resource economy, and minimizing the carbon footprint, among others. Progress has been made in the estimation of energy and protein requirements in sheep and goats, mainly utilizing empirical feeding experimentation, comparative slaughter technique and minimum endogenous loss method. In sheep, newer estimates of energy and protein requirements for maintenance and growth and partial efficiencies had been reported since 2007. There were suggestions that energy and protein requirements could have been affected by breed, wool growth, gender and size; with these reported values being similar or lower than the recommended values in international feeding systems such as NRC, ARC, INRA and AFRC. In goats, energy and protein requirements for growing goats were reported to be either higher or lower than the established recommendations, depending upon meat or dairy breeds. Effect of gender on energy requirement appeared to be related to the stage of growth or degree of maturity. Newer data also suggested that the guidelines of the major feeding systems for the entire growth phase may not be adequate for non-pregnant and non-lactating pubertal females. In multiparous pregnant goats, energy and protein requirements for maintenance did not appear to be affected by days of pregnancy, but efficiencies of metabolizable energy and metabolizable protein utilization for pregnancy were. There were suggestions that that metabolizable protein synthesis in the rumen can be predicted from energy intake using combined equations that encompass both sheep and goats, but more data on goats were called for to account for specific differences in nutrition. In addition to sulfur, there has been progress made on the estimation of maintenance and growth requirements of calcium, phosphorus, potassium and magnesium in goats, with suggestions on the consideration of gender and breed differences. Species, level of Intake, genotype, mature size, age, gender, body composition, use of tissue energy, activity, season, and acclimatization continue to be important considerations for the estimation of nutrient requirements in sheep and goats, with emerging factors such as climate change, heat stress, parasitism and secondary plant compounds. Model equations and partial efficiencies used by NRC to predict energy and protein requirements for maintenance, growth, lactation, and fiber have been highlighted and discussed for the purpose of a more focus discussion and refinement for the future. Potential and limitation of both traditional and emerging methodologies in determining the nutrient requirements in sheep and goats were discussed. To justify the research investment, emerging methodologies such as nutrigenomics will have to be linked more directly to the improvement of production efficiency via more precise prediction of nutrient requirement.

With the increase of the Artificial Neural Network (ANN), machine learning has taken a forceful twist in recent times. One of the most spectacular kinds of ANN design is the Convolutional Neural Network (CNN). The Convolutional Neural Network (CNN) is a technology that mixes artificial neural networks and up to date deep learning strategies. In deep learning, Convolutional Neural Network is at the center of spectacular advances. This artificial neural network has been applied to several image recognition tasks for decades and attracted the eye of the researchers of the many countries in recent years as the CNN has shown promising performances in several computer vision and machine learning tasks. This paper describes the underlying architecture and various applications of Convolutional Neural Network.

Abstract: NFinFET transistors with fin channel length 90nm and a planar MOSFET transistor with channel length 180nm and 90nm are presented with characteristic curves at various gate biases. A finalized algorithm with kink effects is effectively responsible for addressing the field effect transistors. The algorithm includes the modified conventional current-voltage formula and a nonlinear heat-associated kink solution which is simplified as a Gaussian form. Three parameters in modified model includes kN (related with channel width, channel length, and gate oxide capacitor, and proportional to the mobility of carriers)Vth(Threshold Voltage), and (the inverse of Early Voltage). Those parameters are determined to minimize the discrepancies between the measured data and the fitting values, but leave kinks located at around (VGS－Vth), which are deliberately eliminated by the Gaussian form because of the agitation of thermal kink effects. The whole fitting is made to be as close as the as-measured IDS-VDS. In the mean time, those determined parameters are physically meaningful after the analysis has been done.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

Discovery of microRNAs (miRNAs) twenty years ago, has advocated a new era of “Molecular Genetics”. About 2000 miRNAs are present, that regulate one third of the genome. MiRNAs dysregulated expression may contribute to several diseases including tumor growth. Their presence in body fluids, reflecting levels alteration in various cancers, merit circulating miRNAs as the “next generation biomarkers” for early stages tumor diagnosis and/or prognosis. Herein, we performed a comprehensive literature search focusing on the origin, biosynthesis and role of miRNAs and summarized the foremost studies centering on miRs value as non-invasive biomarkers in different non-communicable diseases, including various cancer types. Moreover, during chemotherapy many miRNAs were linked to multidrug resistance, via modulating numerous biological processes and/or pathways that will be highlighted as well.

One of the most prevalent illnesses, diabetes does not directly result in patient mortality. But, it increases the risk of death. Any disease that may be predicted in its early stages can lessen its fatal effects while also enhancing the quality of the healthcare system. For the early-stage prediction of diabetes or such types of non-communicable diseases, we need the proper set of influential features. This research has developed a machine learning-based disease prediction model to identify the influential features for diabetes prediction and give a near-perfect classification accuracy. This model includes Min-Max normalization for data normalization, Isolation Forest (iForest) for outlier removal, Synthetic Minority Oversampling Technique (SMOTE) for oversampling, Random Forest based Recursive Feature Elimination (RFE-RF) test, Chi-Square test, and Minimum Redundancy Maximum Relevancy (mRMR) test based feature selection methods for identifying the influential features, and Support Vector Machine (SVM), K Nearest Neighbor (KNN), and Naive Bayes (NB) for the classification. The results clarify that the proposed model outperforms the previous models and studies. The SVM has attained an accuracy of 99.58% in classification using the five features chosen from the Chi-Square test. Lastly, SHAP, an explainable AI model, has been used to assess the classifier model’s performance. These selected features and the classifier model can be used for early-stage diabetes prediction.