Decoctions, macerations and fumigations of the stem bark and wood of Terminalia brownii Fresen. are used in traditional medicine for fungal infections and as pesticides on field crops and in traditional granaries in Sudan. In addition, T. brownii is commonly used for protecting wooden houses and furniture. Therefore, using agar disc diffusion and macrodilution methods, eight extracts of various polarities from the stem wood and bark were screened for their growth inhibitory effects against filamentous fungi commonly causing fruit, vegetable and grain decay, as well as infections in the immunocompromised host. Ethyl acetate extracts of the stem wood and bark gave the best antifungal activities, with MIC values of 250 µg/ml against Nattrassia mangiferae and Fusarium verticillioides, and 500 µg/ml against Aspergillus niger and Aspergillus flavus. Aqueous extracts gave almost as potent effects as the ethyl acetate extracts against the Aspergillus and Fusarium strains, and were slightly more active than the ethyl acetate extracts against Nattrassia mangiferae. Thin layer chromatography, RP-HPLC-DAD and tandem mass spectrometry (LC-MS/MS), were employed to identify the chemical constituents in the ethyl acetate fractions of the stem bark and wood. The stem bark and wood were found to have a similar qualitative composition of polyphenols and triterpenoids, but differed quantitatively from each other. The stilbene derivatives, cis- (3) and trans- (4) resveratrol-3-O-β-galloylglucoside, were identified for the first time in T. brownii. Moreover, methyl-(S)-flavogallonate (5), quercetin-7-β-O-di-glucoside (8), quercetin-7-O-galloyl-glucoside (10), naringenin-4`-methoxy-7-pyranoside (7), 5,6-dihydroxy-3`,4`,7-tri-methoxy flavone (12), gallagic acid dilactone (terminalin) (6), a corilagin derivative (9) and two oleanane type triterpenoids (1) and (2) were characterized. Our results justify the traditional uses of macerations and decoctions of T. brownii stem wood and bark for crop and wood protection and demonstrate that standardized extracts could have uses for the eco-friendly control of plant pathogenic fungi in African agroforestry systems. Likewise, our results justify the traditional uses of these preparations for the treatment of skin infections caused by filamentous fungi.

Introduction: Parents’ behavior and practices affect many aspects of family life, including health, and many studies have proven that children's bad habits are associated with parents’ behavior and practices. Objectives: This study aimed to identify parents’ negative behaviors that might affect their families’ health and social development. Methodology: A descriptive cross-sectional study was conducted to examine the influence of parents’ behavior and practices on their family health, in which 192 respondents participated. Results: The results clarified the influence of parents on family health in several aspects. On the behavioral side, approximately 90% of the participants agreed that the behavior of parents may affect the behavior of their families, and the social and educational side results clarified the relationship between parents' illiteracy and support for the cognitive and social health of the family. Discussion: This study clarified that there is a significant relationship between illiterate parents and their ability to support their families, illustrating that the majority of participants thought that the development of the cognitive and social health of families depends on the presence of supportive parents, which has many implications for family social and psychological health. Conclusion: Parental behaviors and practices have a strong effect on their family’s health, which affects the development of the families’ cognitive and social health. Recommendation: The study recommends the need for supportive, friendly hospitals for family social health and the provision of specialized programs that support the family’s social and psychological health.

Limited understanding exists regarding the intricate dynamics between the levels of social inhi-bition exhibited by both wives and husbands concerning their perceived family support and de-pressive symptoms, particularly within couples who are parents of children diagnosed with au-tism spectrum disorder (ASD). This study used the actor-partner, interdependence mediation model to analyze data collected from 397 pairs of Chinese parents with children diagnosed with ASD. The findings of the study revealed significant indirect actor effects, indicating that the levels of social inhibition exhibited by both wives and husbands were associated with their own de-pressive symptoms through their respective perceptions of family support. In general, the study did not find significant partner effects, except for some indirect effect (IE) of wives on their hus-bands' depressive symptoms through the wives' perceived social support. This observation sug-gests that cultural norms and role expectations within the family context may influence these dy-namics. These results underscore the potential importance of interventions aimed at addressing social inhibition and enhancing perceived family support to alleviate depressive symptoms in this population. Additionally, interventions targeting fathers should emphasize the importance of their involvement in parenting and collaboration with their partners in caring for children with ASD. Such collaborative efforts may contribute to improved outcomes for both parents and chil-dren within families affected by ASD.

Stallion mules have been used as working equids in several countries. Aggressiveness, under the influence of testosterone, resulted in the necessity for surgical castration before work training. The gonadotropin-releasing hormone (GnRH) vaccine may be an alternative method for immunocastration in mules. The objectives were to evaluate the effect of GnRH vaccine on anti-GnRH antibody production, serum testosterone level, clinical adverse effects, and behavior toward human manipulation. Twenty-five mules were separated into 3 groups: Control-intact, Control-castrated, and Treatment. Treatment was further divided into subgroups according to condition (intact or unilateral cryptorchid) and age. Treatment received 195 µg GnRH vaccine intramuscularly at week 0, 4, and 8. Anti-GnRH antibody increased at week 6 and 10, then gradually decreased to baseline at week 22. Treatment-intact-young had the highest anti-GnRH antibody, resulting in lower serum testosterone levels during week 2-6 and 12-16 compared to Control-intact. Subcutaneous edema adjacent to the injection site was detected only in Treatment-intact after booster vaccination. During week 6-22, the behavioral scores of Treatment significantly changed toward at ease with human contact compared to a score before vaccination. In conclusion, mules responded to GnRH vaccine, which could temporarily suppress testosterone for up to 16 weeks.

.Maize cultivation in Thailand faces challenges owing to climate change and soil organic carbon (SOC) loss. This highlights the importance of comparing maize soil with paddy soil in terms of the role of dissolved organic carbon (DOC) and nutrient availability, as they influence SOC content. Soil samples from Chiang Mai province, primarily Fluvisol, were collected for the cultivation of paddy rice and maize, analysed for carbon fractions and chemical properties, and categorised into layers. Comparative analysis revealed that maize soils had lower levels of labile carbon components and organic carbon than paddy soils (P

In recent years, growing attention has been directed towards the potential of plant extracts as great therapeutic agents in controlling oxidative stress and inflammation. Gymnema inodorum (Lour.) Decne, an indigenous plant locally grown in Northern Thailand, is known for its anti-diabetic activity. This study aims to explore the antioxidant properties and phenolic profile of column chromatographic fractionated G. inodorum leaf extract. The ethanolic-reflux extracts of G. inodorum leaves were subjected to column chromatography for the isolation of bioactive molecules. Total phenolic and flavonoid content were assessed using Folin–Ciocalteu and aluminium chloride colorimetric methods, respectively. Total antioxidant activity was evaluated by employing different antioxidant assays, including 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulfonic)acid (ABTS) scavenging assay and ferric reducing antioxidant power (FRAP) assay. High-Performance Liquid Chromatography (HPLC) with a C18 column was employed to determine the level of gymnemic acid, while Liquid Chromatography Quadrupole Time-of-Flight/Mass Spectrometry (LC-QTOF/MS) was used to identify potential phenolic compounds. The three separated fractions indicating A, B, and C, exhibited remarkable antioxidant activity, with total phenolic content of 0.294 ± 0.056, 0.085 ± 0.039, and 0.227 ± 0.041 mg QE/mL, and total flavonoid content of 0.274 ± 0.050, 0.309 ± 0.110, and 0.384 ± 0.007 mg QE/mL, respectively. Fraction A exhibited the highest DPPH and ABTS scavenging activity, while fraction C demonstrated significantly higher ferric-reducing power. HPLC analysis revealed a highest concentration of gymnemic acid in fraction C (0.393 ± 0.003 mg/g) compared to fraction A (0.159 ± 0.003 mg/g) and fraction B (0.142 ± 0.000 mg/g). The LC-QTOF/MS phenolic screening showed seven potential phenolic compounds in fraction A, seven compounds in fraction B, and four compounds in Fraction C. A significant relationship is found between antioxidant potential and total phenolic content, suggesting that phenolic compounds are the major contributors to the antioxidant activity of G. inodorum.

Over the past decades, overweight and obesity has become a global epidemic and the leading threat for death. To prevent the serious risk, an overweight or obese individual must apply a long-term weight-management strategy to control food intake and physical activities, which is however, not easy. Recently, with the advances of information technology, more and more people can use wearable devices and smartphones to obtain physical activity information, while they can also access various health-related information from Internet online social networks (OSNs). Nevertheless, there is a lack of an integrated approach that can combine these two methods in an efficient way. In this paper, we address this issue and propose a novel mobile-social framework for health recognition and recommendation, namely, H-Rec². The main ideas of H-Rec² include (1) to recognize the individual's health status using smartphone as a general platform, and (2) to recommend physical activity and food intake based on personal health information, life science principles, and health-related information obtained from OSNs. To demonstrate the potentials of the H-Rec² framework, we develop a prototype that consists of four important components: (1) an activity recognition module that senses physical activity using accelerometer, (2) a health status modeling module that applies a novel algorithm to generate personalized health status index, (3) a restaurant information collection module that collects relevant information from OSN, and (4) a restaurant recommendation module that provides personalized and context-aware recommendation. To evaluate the prototype, we conduct both objective and subjective experiments, which confirm the performance and effectiveness of the proposed system.

In this paper we perform numerous numerical studies for the problem of low-rank matrix completion. We compare the Bayesian approaches and a recently introduced de-biased estimator which provides a useful way to build confidence intervals of interest. From a theoretical viewpoint, the de-biased estimator comes with a sharp minimax-optimal rate of estimation error whereas the Bayesian approach reaches this rate with an additional logarithmic factor. Our simulation studies show originally interesting results that the de-biased estimator is just as good as the Bayesian estimators. Moreover, Bayesian approaches are much more stable and can outperform the de-biased estimator in the case of small samples. However, we also find that the length of the confidence intervals revealed by the de-biased estimator for an entry is absolutely shorter than the length of the considered credible interval. These suggest further theoretical studies on the estimation error and the concentration for Bayesian methods as they are being quite limited up to present.

The TiO₂ nanostructures resulted by pyrolysis of TiCl₄ at low temperature of 80 ^oC are found to be a mixture of amorphous TiO₂ complexes and anatase nanostructure whose ratio depends on the pH of the pyrolysis medium. At low pH level, the resulting TiO₂ nanostructure is predominant anatase and gradually shifts to the amorphous TiO₂ complexes with pH level increasing. By means of heat treatment, the amorphous TiO₂ complexes can be converted back to the anatase nanostructure and then transform to rutile with the elevating temperature. Amongst of the TiO₂ nanostructure recovered from amorphous TiO₂ complexes, the anatase shows to be the most effective photocatalyst in decomposition of methylene blue.

Mangrove ecosystems play an important role in local livelihoods in coastal regions of tropical and subtropical countries. However, in recent years urbanisation has changed the income structure of residents near mangroves. Different landscapes provide different job opportunities; thus, analysis of regional landscape patterns is important for understanding income structures. In this study, surveys on the income structure and landscape patterns of the surrounding areas of three mangrove sites were conducted in the Hau and Hoang Mai River estuaries in Nghe An Province, North-Central Vietnam. The results revealed that both natural and socio-economic landscape components affected income structure. The major occupations in the study area were agriculture, including husbandry, sea fishing, and trading. Land morphology and river type were the major factors influencing the income from agriculture, while coastline morphology primarily affected income from sea fishing. Community-based trading was carried out in the study area; thus, the population inside each administrative unit was a significant factor increasing income, while the retail market size in an area had significant negative effects, potentially due to the increasing number of competitors. Our study aimed to evaluate mangrove ecosystem importance for local livelihoods in relation to landscape patterns, and the results contribute to urban planning based on the conservation and sustainable use of mangrove ecosystems.

In northern Thailand, the problem of small particulate matter happens every year, with the pri-mary source being agricultural weed burning and wildfire. The tourism industry is strongly impacted and has been the spotlight for the past few years. Thus, the study aims to investigate the effect of small particulate matter on tourism and related SMEs in Chiang Mai, Thailand. The data was collected from 286 entrepreneurs in the tourism and related SMEs sectors. The data was analyzed using data mining and association rule techniques. The study revealed that small particulate matter has a considerable impact on customer factors, especially the number of customers has decreased. Operational factors and prod-uct/service factors are also affected by the dust in the form of adjustments to keep the business running and the protection of the health of employees and customers. Certainly, financial factors are affected by the small particulate matter situation, both lower revenues and higher costs.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

Owing to fascinating applications of ZnO in modern devices, it is interesting to explore its more features for future devices. Hence, herein, we have synthesized the high quality ZnO spherical nanoparticles (SNPs) through a facile green synthesis route and robust structural and biomedical studies are carried out. Hexagonal phase with 93.2% crystallinity was confirmed through XRD analysis. ZnO nanoparticles were tested for their bioactivities both in vivo (acute cytotoxicity test) and in vitro (Anti-cancer activities on liver (HepG2) and cervical (Hela) cancer cell lines, stimulatory/inhibitory effects on normal rat splenic cells and hemolytic effects on red blood cells). Results showed that ZnO SNPs has no cytotoxic effects on vital organ like liver and has no hemolytic action on red blood cells. ZnO SNPs showed inhibitory consequence on normal rat splenic cells growth at all tested concentrations. ZnO nanoparticles showed an inhibitory effect on HepG2 cell line. While showed stimulatory effect on Hela cell line. Current study presents the synthesized ZnO SNPs as highly applicable in bio-optoelectronics.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

Recent developments in optical biosensors based on integrated photonic devices are reviewed with a special emphasis on silicon-on-insulator ring resonator. The review is mainly devoted to the following aspects: (1) Principles of sensing mechanism, (2) sensor design, (3) biofunctionalization procedures for specific molecule detection and (4) measurement set-ups and advances in chip-integration. The inherent challenges of implementing photonics-based biosensors to meet specific requirements of applications in medicine, food analysis, and environmental monitoring are discussed.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

In this paper, inspired by recent articles of G. Anatriello and G. Vincenzi (see \cite{Ana}), and G. Cerda-Morales (see \cite{Cer1,Cer2}), we will introduce the third-order $\overline{h}$-Jacobsthal and third-order $\overline{h}$-Jacobsthal--Lucas sequences and their associated quaternions. The new results that we have obtained extend most of those obtained in \cite{Cer2}.

Two-phase olive pomace is a byproduct of the olive-oil extraction process that is sometimes processed further to recover more oil. During pomace oil production, especially in the early stages of olive processing, odours can be produced. These odours are a serious nuisance especially in and around the processing facilities, as well as for nearby communities. These odours can be strong and unpleasant, and they may result in various issues, including environmental concerns. Thus, in this paper, the effect of storage and drying on the composition of two-phase olive pomace was investigated. Several physicochemical and instrumental analyses were performed and it was concluded that the structural elements of pomace are not the ones who are affected during storage and drying. Storage and drying mainly impact the oil content of pomace, leading to an acidity increase and to the production of odorous oxidation compounds. Volatile acids, methyl and ethyl esters are released into the atmosphere causing serious environmental nuisance.

Fall armyworm Spodoptera frugiperda (J.E. Smith, 1797) is a major pest of corn, rice, and sorghum among other crops usually controlled using synthetic or biological insecticides. Currently, the new invention of nanotechnology is taking root in the agricultural industry as an alternative source of pest management that is target-specific, safe, and efficient. This study sought to determine the efficacy of commercial Zinc Oxide (ZnO) nanoparticles (NPs) towards S. frugiperda under labora-tory conditions. ZnO NPs were diluted into different concentrations (100- 500ppm), where the baby corn used to feed the S. frugiperda larvae was dipped. The development of the insect feeding on food dipped in ZnO solution was significantly (p<0.05) affected, and the number of days that the insect took to complete its life cycle had a significant difference compared to the control. There was a significant difference in the adults’ emergence at all the concentrations of ZnO NPs compared to the control, with over 90% of the eggs successfully going through the cycle until adult emergence. Additionally, several malformations were observed throughout the lifecycle of the insect. Also, the fecundity of the females was greatly affected. The findings of this study suggest the possibility of exploitation of ZnO nanoparticles not only to eradicate S. frugiperda but to significantly reduce their population in the ecosystem through deformations, reduced fecundity, reduced oviposition, and hatchability of eggs. It will be a valuable tool in integrated pest management regimens.

By the end of 2023, biowaste must be completely separated or recycled at source based on the EU legislation. Separate biowaste collection and valorisation towards biofuels could play an essential role in the biobased circular economy. In this context, the principal goal of this paper was to demonstrate in pilot scale the technological solution of bioethanol production via the utilisation of urban source-separated biowaste within the city context of Athens, Greece. More specifically, the main aim was the demonstration of a pilot system in continuous operation (over 10 operating cycles) with real feedstock – wet separately collected biowaste. From the 11 pilot trials performed with wet feedstock, the mean starch and cellulose degradation of the pilot trials amounted up to 80.69±16.27% and 79.41±10.37% respectively, while the bioethanol yield was 74.05±6.82%. The latter was comparable to that of more intensive pretreatment methods. Homogenization and shredding that was applied in this study, stand as promising and cost-effective pretreatment methods for bioethanol production from wet feedstock. Further research is needed to optimize conditions and evaluate scalability. Nevertheless, pilot scale testing is a crucial step in the development and deployment of this technology since it serves as a bridge between laboratory research and full-scale implementation, offering a practical and controlled environment to validate and optimize the technology while minimizing risks and uncertainties.

We have investigated the antiferromagnetic phase transition in the frustrated and multiferroic hexagonal manganites $h$-(Y$_{0.98}$ Eu$_{0.02}$)MnO$_3$ (YEMO) and $h$-YMnO$_3$ (YMO). Elastic neutron scattering has been used to study in detail the phase transition in YMO and YEMO in zero pressure and in YMO at a hydrostatic pressure of 1.5~GPa. In zero pressure, we find the critical temperature $T_{\rm N} = 72.11(5)$~K and 71.3(1)~K and the critical exponent $\beta = 0.206(3)$ and 0.22(2), for YEMO and YMO, respectively. This is in agreement with earlier work by Roessli {\em et al.}. In applied hydrostatic pressure of 1.5~GPa, the ordering temperature increases to $T_{\rm N} = 75.2(5)$~K, in agreement with earlier reports, while $\beta$ is unchanged. Inelastic neutron scattering was used to determine the anisotropy spin wave gap at the phase transition, expected from spin wave theory to close with a critical exponent $\beta'$ identical to the one of the order parameter, $\beta' = \beta$. Our results indicate that the gap in YEMO indeed closes at $T_{\rm N}=72.4(3)$~K with $\beta' = 0.24(2)$, while the in-pressure gap in YMO closes at 75.2(5)~K with an exponent of $\beta' =0.19(3)$. In addition, the low-temperature anisotropy gap was found to have a slightly higher absolute value under pressure. The consistent values obtained for $\beta$ in the two systems support the likelihood of a new universality class for triangular, frustrated antiferromagnets.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

The human landscape transforming activity contributes to the global change of vegetation in different forms. Hunting is one of the most ancient human landscape-shaping activities. Feeders for hunting are particularly disruptive to vegetation. In the present study, we conducted a vegetation survey in these highly disturbed places. We are investigating the vegetation dynamics over several years in in the turkey oak–sessile oak zone, in two areas with different moisture and shade conditions (forest and clearing). One important background factor is changes in precipitation and temperature. The novelty of our present study lies in the fact that the observation takes place with continuous disturbance, where the human influence is very large. Our results confirm that the weed infestation be detectable at bait sites over a long period, and the interannual changes were typical in every year, according to the fact that in August, more weed species are usually present with a greater cover at the bait sites. The main meteorological factors played a role in the degree of weed infestation in each year. There was a higher proportion of vegetation regeneration in wetter years, while dry periods do not favor successional processes. With the drying of the climate, the disturbed areas are constantly losing their natural value, but wetter weather is not an automatic solution either. A more precise understanding of vulnerable systems and careful planning of treatment interventions is necessary.

We report on the occurrence of natural Magnesium Alumina Silicate Hydrate (M-(A)-S-H) cement at Feragen and Leka in eastern and western Trøndelag Norway, respectively. Both occurrences are located in the sub-arctic climate zone and form in glacial till and moraine material deposited on ultramafic rock during the Weichselian glaciation. Weathering of serpentinized peridotite dissolve brucite and result in a relative high pH alkaline fluid that subsequently reacts with the felsic minerals of the till (quartz, plagioclase, K-feldspar) to form a cement consisting of an amorphous material or a mixture of nanocrystalline Mg-rich phyllosilicates, including illite. The presence of plagioclase in the till results in the enrichment of alumina in the cement, i.e., forms M-A-S-H instead of the M-S-H cement. Dissolution of quartz results in numerous etch-pits and negative quartz crystals filled with M-A-S-H cement. Where the quartz dissolution is faster that the cement precipitation, a honeycomb-like texture is formed. Compositionally the cemented till (tillite) contains more MgO and has a higher loss of ignition than the till, suggesting that the cement is formed by a MgO fluid that previously reacted with the peridotite. The M-(A)-S-H cemented till represent a new type of duricrust, coined magsilcrete. The study of natural Mg-cement provides information on peridotites as a Mg-source for Mg-cement and as a feedstock for CO2 sequestration.

Statement of problem: Henna has been added to polymethylmethacrylate (PMMA) as a new type of antifungal agent; however, its effect on the latter’s physical properties has not been investigated. Purpose: This study aimed to evaluate the effect of the addition of various henna concentrations on the surface roughness and hardness of PMMA denture base material. Materials and Methods: A total of 99 specimens of rectangular-shaped (10×20×3 mm3) acrylic specimens were prepared from heat-cured acrylic resin. Specimens were divided into one control group without the addition of henna and five test groups, which were prepared by adding Yamani henna powder to acrylic powder at concentrations of 1wt%, 2.5wt%, 5wt%, 7.5wt%, and 10wt%. The polymer was added to the monomer before being mixed, packed, and processed using the conventional water bath method. After processing, specimens were finished and polished, then kept in distilled water for 48+2 h. A profilometer and Vickers hardness tester were used to measure surface roughness and hardness respectively. Statistical data analysis was conducted via SPSS version 20.0 (IBM, USA). Results: The addition of henna at varying concentrations significantly increased surface roughness values (P ≤ 0.01) while decreasing hardness (P ≤ 0.0001). The most favorable addition value was 1% henna between all henna groups. Conclusion: The addition of henna to the acrylic resin may negatively affect the surface properties of PMMA acrylic denture base.

In this paper a full state feedback control of a double inverted pendulum on a cart (DIPC) are designed and compared. Modeling is based on Euler-Lagrange equations derived by specifying a Lagrangian, difference between kinetic and potential energy of the DIPC system. A full state feedback control with H infinity and H 2 is addressed. Two approaches are tested: open loop impulse response and a double inverted pendulum on a cart with full state feedback H infinity and H 2 controllers. Simulations reveal superior performance of the double inverted pendulum on a cart with full state feedback H infinity controller.

Using the h-index to assess individual researchers is not only unethical and unfair but also inaccurate and misleading. This index fails to offer a reliable measure of a researcher's impact based on their citation scores. Beyond statistical and conceptual considerations, authorship practices, especially in the case of multi-authored publications, give rise to significant problems that often go unnoticed. While some modifications of the h-index have been proposed to mitigate these weaknesses, the fundamental deficiencies persist. Most of these flaws have been effectively addressed by the c-score, a composite citation index. The c-score excludes self-citations, normalizes the number of citations by considering the number of authors in each paper, and takes into account first, single, and last authorship. This approach provides a more realistic measure of the impact of each individual researcher based on raw citations.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

In this data deposit, I describe a dataset that is the result of content mining 167,318 published articles for statistical test results. As a result of this content mining, 688,112 results from 50,845 articles were extracted. In order to provide a comprehensive set of data, the statistical results are supplemented with metadata from the article they originate from. The dataset is provided in a comma separated file (CSV) in long-format. For each of the 688,112 results, 20 variables are included, of which seven are article metadata and 13 pertain to the individual statistical results (e.g., reported and recalculated p-value). A five-pronged approach was taken to generate the dataset: (i) collect journal lists, (ii) spider journal pages for articles, (iii) download articles, (iv) add article metadata, and (v) mine articles for statistical results.

In this paper, we propose an imagined speech-based brain wave pattern recognition using deep learning. Multiple features were extracted concurrently from eight-channel Electroencephalography (EEG) signals. To obtain classifiable EEG data with fewer number of sensors, we placed the EEG sensors on carefully selected spots on the scalp. To decrease the dimensions and complexity of the EEG dataset and to avoid overfitting during the deep learning algorithm, we utilized the wavelet scattering transformation. A low-cost 8-channel EEG headset was used with MATLAB 2023a to acquire the EEG data. The Long-Short Term Memory Recurrent Neural Network (LSTM-RNN) was used to decode the identified EEG signals into four audio commands: Up, Down, Left, and Right. Wavelet scattering transformation was applied to extract the most stable features by passing the EEG dataset through a series of filtration processes. Filtration has been implemented for each individual command in the EEG datasets. The proposed imagined speech-based brain wave pattern recognition approach achieved a 92.50% overall classification accuracy. This accuracy is promising for designing a trustworthy imagined speech-based Brain-Computer Interface (BCI) future real-time systems. For better evaluation of the classification performance, other metrics were considered, and we obtained 92.74%, 92.50% and 92.62% for precision, recall, and F1-score, respectively.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

A modular approach to the construction of electric machines, drive systems, power supply systems is a new direction of modern technology development. Especially, the modular approach is promising for electric vehicles due to such positive aspects as increased efficiency, fault tolerance, overall reliability, safety, enhanced control capabilities, etc. In this work, the modular approach is comprehensively applied to an EV powertrain system, which includes a dual three-phase (DTP) BLDC motor with two machine modules of an asymmetric configuration, two battery modules and a supercapacitor module (SCM). The proposed H–H configuration of modular EV powertrain system includes four voltage source inverters that combine the power modules with the open ends of the windings (OEW) of the module machine armature, and provide control of their operation. Based on the developed mode system of the OEW machine module operation for EV traction and braking, a general control algorithm for the proposed configuration of the modular EV powertrain system has been developed. It combines the control of the operating modes with the functions of maintaining the required SOC level of the SCM and equalizing the SOCs of the two battery modules. The conducted simulation and experimental studies confirmed the workability and effectiveness of the proposed solutions.

In this paper, the design and analysis of coupled tank water level control system is done using robust control theory. The main aim of this work is to improve level controlling mechanisms in industries and household areas. In this paper, H ∞ and μ –synthesis controllers are designed to improve the level control system. The coupled tank water level control system is designed using the proposed controller’s comparison and tested for tracking a reference level signals (step, sine wave and random) and simulation results have been analyzed successfully. Finally the comparative simulation results prove the effectiveness of the proposed coupled tank water level control system with H ∞ controller for improving the tracking mechanism performance of the system.

In this work, we introduce the class of h-MN-convex functions by generalizing the concept of MN-convexity and combining it with h-convexity. Namely, let M : [0, 1] → [a, b] be a Mean function given by M (t) = M (t; a, b); where by M (t; a, b) we mean one of the following functions: A_t (a, b) := (1 − t) a + tb, G_t (a, b) = a^1−tb^t and H_t (a, b) := $\frac{ab}{ta+\left(1-t\right)b}=\frac{1}{A_t\left(\frac{1}{a},\frac{1}{b}\right)}$ with the property that M (0; a, b) = a and M (1; a, b) = b. Let I, J be two intervals subset of (0, ∞) such that (0, 1) ⊆ J and [a, b] ⊆ I. Consider a non-negative function h : J → (0, ∞), a function f : I → (0, ∞) is said to be h-MN-convex (concave) if the inequality f (M (t; x, y)) ≤ (≥) N (h(t); f (x), f (y)), holds for all x, y ∈ I and t ∈ [0, 1]. In this way, nine classes of h-MN-convex functions are established, and therefore some analytic properties for each class of functions are explored and investigated. Characterizations of each type are given. Various Jensen’s type inequalities and their converses are proved.

This study aims to construct simple devices to ascertain the concentrations of ammonium (NH4+) and nitrate (NO3-). The device structure comprises a visible and near-infrared absorption meas-urement room, along with an RGB (red, green, and blue) absorption measurement room, con-stituting the two measuring rooms. Both the measurement rooms are equipped with light sources and detectors configured to operate in opposed or thru-beam modes. A tiny processor is utilized for processing the measurements, with an algorithm implemented within its memory. During the algorithm development phase, ranges for measuring the quantity of nutrients were categorized using a discriminant analysis approach. Thirty percent of the soil sample data were utilized as verification data, while the remaining 70 percent served as training data. Nutrient content values from reliable measuring instruments were incorporated into all datasets. Discriminant analysis was employed to classify the amount of NH4+ into five ranges based on the test results. When tested with soil samples, the accuracy was 66.13% compared to the reference value of a reliable measuring device. Similarly, NO3- was classified into four ranges with an accuracy of 81% com-pared to the reference value of a reliable measuring device.

One of the main challenges of cultured meat is reducing the costs of production, often described as scaling. The main components of the cultivation process include: cells, media, scaffolds and bioreactors. This work presents an alternative to current stainless steel or glass bioreactors and uses food-grade plant-based scaffolds. Bioreactors must be sterile and leak-free to maintain a proper environment for cell growth. Thermoplastic films are a popular material for constructing these fluidic systems, but traditional methods of welding these film are expensive and do not allow rapid prototyping resulting in high research and development costs for companies. In this study, a laser welding method was developed to join thermoplastic films in a way that prevents contamination and leaks, affording effective macro-fluidics fabrication. This technique was tested using polyethylene (PET) films and a laser cutter operating with settings calibrated for the material to be welded or cut. The laser welding method was found to produce strong, leak-free seals in PET films with minimal heat-induced damage to the films. The ability to design fluidics, chambers and ports of various size. Using this method afforded the incorporation of plant-based scaffolds from food-grade plants (Rice). The laser welding method developed in this study provides a reliable, contamination-free method for the rapid fabrication of fluidic systems for cell cultivation. This technique has the potential to be compatible with a vast range of cell types and scaffolds and to be widely adopted in tissue engineering for regenerative medicine and food applications such as cultured meat.

Significant changes have occurred at Arabian Gulf Coast of Saudi Arabia over the last three decades. The area of mangrove was reduced by about 55%. Thus the economic, social, and environmental value of mangroves must be assessed over short -to long-term scales and employ these assessments for the awareness rising at local communities. This study provides a preliminary assessment of the risks on mangrove vegetation; it will provide database to mitigate the tremendous pressures due to coastal development and urban activities. The effects of human development on the mangrove plant cover in Eastern Region of KSA were recognised, during 2013 to 2016. The mean variations of physio-chemical characteristics in water and sediment were recorded. With regard to water analyses including; nitrogen, phosphorus, TSS, TDS, BOD, and turbidity were evaluated. On the other hand, for sediment: TDS, nitrogen, phosphorus, sulphate and total organic carbon were assessed. Moreover, the growth parameters: plant height, and size index, of Avicennia marina were recorded and estimated. It is concluded that human impact and urban developments have exerted drastic effects on the coastal ecosystems and its environments.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

Background: World Health Organization (WHO) estimates that there were 558000 new cases with resistance to Rifampicin, of which 82% had multidrug-resistant tuberculosis (MDR-TB). Objectives: We aimed to identify the prevalence of MDR-TB in River Nile state, Sudan, and the risk factors contributing to its occurrence. Methods: This was a descriptive cross-sectional hospital-based study involved 200 specimens taken from patients suspected of having MDR-TB tested using an automated GeneXpert assay. Results: Results of GeneXpert assay showed that the presence of Mycobacterium tuberculosis in 81 (40.5%), and out of 81 positive test results there were 13 (16%) had MDR-TB. Additionally, 7 cases of MDR-TB were previously treated which represented about (53%) of MDR patients, the remaining 6 MDR-TB patients were new cases and represented (47%) of MDR-TB patients. Moreover, there were 4 MDR-TB patients who had a history of contact with MDR-TB patients. Conclusion: Prevalence of MDR-TB in River Nile State, Sudan was 16%, which is greater than WHO estimation for Sudan (10.1%). The results revealed that the main risk factor to develop MDR-TB was a history of contact with MDR-TB, so adherence to treatment and social awareness about the spread of MDR-TB are crucial preventive measures.

This study aimed to characterize the genetic subtypes of HCV-GT4 and identify the presence of natural occurring resistance-associated substitutions (RASs) in Saudi Arabia patients. A total of 17 GT4 patients was analyzed. Sequence analysis of NS3, NS5A and NS5B regions was performed by direct sequencing. In addition, phylogenetic analysis was used to determine genetic subtypes, RAS and polymorphisms. Nine patients were infected by a GT4a, one with GT4o, 3 with GT4d. The remaining four patients were infected with a recombinant virus (GT4a+GT4o in three patients, GT4c+GT4d in a patient). Natural RASs were found in six patients (35%), including three infected by GT4a, two by GT4a+GT4o and one patient infected by GT4c+GT4d. In particular, NS3-RAS V170I was demonstrated in three patients, while NS5A-RASs (L28M, L30R, L28M+M31L) were detected in the remaining three patients. All patients were treated with sofosbuvir plus daclatasvir; three patients were lost to follow-up whereas 14 patients completed the treatment. A sustained virological response (SVR) was obtained in all but one patient carrying NS3-RAS V170I who later relapsed. GT4a is the most common subtype in this small cohort of Saudi Arabia patients infected with hepatitis C infection. Natural RASs were observed in about a third of patients, but only one of them showed a treatment failure.

This paper aims to unify q-derivative/q-integral and h-derivative/h-integral in a single definition, this will be called q−h-derivative/q−h-integral. These notions are further extended on finite interval [a,b] in the form of left and right q−h-derivatives and q−h-integrals. Some inequalities are studied for q−h-integrals which are directly connected with well known results. In diverse fields of science and engineering the theory based on q-derivatives/q-integrals and h-derivatives/h-integrals can be unified by using the concept of q−h-derivative/q−h-integral.

In this study, we define new classes of convexity called of h-Godunova-Levin and h-Godunova-Levin preinvexity, through which some new inequalities of Hermite-Hadamard type were established. These new classes are the generalisation of several known convexity including the s-convex, P-function, Godunova-Levin. Further, the properties of h-Godunova-Levin function were also discussed. Meanwhile, the applications of h-Godunova-Levin Preinvex function are given

In this work, several inequalities of Popoviciu type for h-MN-convex functions are proved, where M and N are denote to Arithmetic, Geometric and Harmonic means and h is a non-negative superadditive or subadditive function.

Renewable resources gain increasing interest as source for environmentally benign biomaterials, such as drug encapsulation/release compounds, and scaffolds for tissue engineering in regenerative medicine. Being the second largest naturally abundant polymer, the interest in lignin valorization for biomedical utilization is rapidly growing. Depending on resource and isolation procedure, lignin shows specific antioxidant and antimicrobial activity. Today, efforts in research and industry are directed toward lignin utilization as renewable macromolecular building block for the preparation of polymeric drug encapsulation and scaffold materials. Within the last five years, remarkable progress has been made in isolation, functionalization and modification of lignin and lignin-derived compounds. However, literature so far mainly focuses lignin-derived fuels, lubricants and resins. The purpose of this review is to summarize the current state of the art and to highlight the most important results in the field of lignin-based materials for potential use in biomedicine (reported in 2014–2018). Special focus is drawn on lignin-derived nanomaterials for drug encapsulation and release as well as lignin hybrid materials used as scaffolds for guided bone regeneration in stem cell-based therapies.

This study aimed to evaluate the effect of incorporating linseed oil and fish oil in the diet on intake, ruminal fermentation milk yield and milk fatty acid profile in dairy goats. Four crossbred Saanen lactating goats in mid-lactation and milking 1.30±0.28 g/day were used in a 4 × 4 Latin square design. The basal diet consisted of concentrate and Para grass (C:F 40:60). Treatments included the basal diet without oil supplement (Ctrl) or with 2.5% linseed oil (LO2.5), 2.5% linseed oil and fish oil (3:2, w/w, LFO2.5), and 4.16% linseed oil and fish oil (3:2, w/w, LFO4.16). Diets had no effect on intake, milk yield, milk composition and ruminal fermentation patterns (P > 0.05). The lower (P < 0.05) proportions of C10:0-C14:0 in milk fat were observed with LFO4.16 compared with Ctrl. Compared with the Ctrl and linseed oil added alone, feeding LFO4.16 resulted in a 589% and 303% increase in C18:1 t11, respectively. Milk c9,t11 CLA was markedly increased with the LFO4.16 diet, accounting for 4.53 and 2.94 times greater concentrations than those in Ctrl and LO2.5 diets, respectively (P < 0.01). Goats fed LFO2.5 and LFO4.16 had greater levels of C22:6n-3 (0.63% and 0.87%; P < 0.001) compared with those fed Ctrl and LO2.5 diets (0.06% and 0.08%). Overall, the combined data suggested that including 4.16% linseed oil and fish oil in the diet of dairy goats is effective for improving the concentrations of healthy fatty acids in milk, without affecting milk production.

Natural dyes offer a bio-based opportunity to support attractive coloration to textile fabrics made from natural fibers like cotton, wool, hemp and many other materials. They can be part of a strategy to realize fully bio-based textile materials and clothing. Following this statement, the actual study investigates the use of wood extracts for dyeing of cotton fabrics. Actually extract powders of Logwood (Haematoxylon campechianum L.), Brazilwood (Caesalpinia spp.), and Quebracho wood (Schinopsis lorentzii) are used. The dyeing process is modified using different mordants based on iron and aluminum salts. These mordants are applied in pre-, meta- or post-mordant procedures. Color and fastness properties of prepared textile samples are determined by spectroscopic measurements, color measurements, washing procedures and Xenotest for measuring the light fastness. Finally, a broad range of different colorations can be realized by different combinations of wood extracts and mordanting procedures. A good wash fastness is reached for some color shades. For reaching good wash fastness, pre- and meta-mordanting procedures are more advantageous compared to post-mordanting. However, the light fastness of realized samples is only moderate to low. In conclusion, it can be stated that dyes from wood extracts are excellent materials to dye natural fibers if they are combined with the right mordanting agent in pre- or meta-mordanting procedures. The actual study is therefore a good proof-of-concept for the realization of fully bio-based colored textile materials.

The importance of understanding the corrosion mechanisms of excavated metal artefacts help in determining the physico-chemical parameters of the burial environment and the formation of different corrosion products. These products can be observed and analysed with the help of various techniques that provide information on their morphology, chemical composition and structure. The analysis of ancient coins is extremely challenging in the presence of heavily corroded surfaces; as quantitative information may not exactly concur with its bulk composition. In the case of silver coins, the use of surface information can be used as a guide for bulk composition only. The current study carries out investigation and characterization of selected coins from a large coin hoard excavated from Amheida, Dakhla oasis, Egypt. The study and analysis of the alloy composition and corrosion products was performed using a multi-technique approach which included Light optical microscopes, Scanning Electron microscope (SEM) coupled with energy dispersive spectroscopy (EDS) and X-ray diffraction analysis. Investigation of the coins revealed the presence of a thick active inhomogeneous corrosion crust, while analysis showed that the coins were made from a binary silver copper alloy (billon) while the corrosion crust was rich in chlorides and carbonates, later identified by XRD analysis as Paratacamite, Malachite and Chrysocolla.

The plant Allium hookeri, belonging to the Allium genus, has a history of being used both as a common food ingredient and in herbal medicine. It has recently been reported to have anti-oxidant and anti-inflammatory effects. A. hookeri has been also shown to exhibit neuroprotective and anti-neuroinflammatory activities, but the active compounds responsible for these effects have not been identified in previous studies. This study aimed to perform a metabolite profiling using an HRESI-qTOF MS/MS-based molecular networking approach and identify the active compounds from A. hookeri that target senescent cell-associated secretory phenotype (SASP) inhibitory effects, which contribute to neuroprotective activities. As a result, ten compounds, including one new flavonoid (2) and nine known compounds (1 and 3–10), were identified, and their biological activity was tested. The most potent compound was N-trans-feruloyltyramine (7), which inhibited SASP markers and contributed to the senomorphic activities of A. hookeri. These findings suggest that the phenolamides from A. hookeri could be a promising source of bioactive compounds for preventing senescence-associated diseases.

On the H-type group G⊂Rm×Rn, we study the existence of solutions for the Brezis-Nirenberg problem

Most Acinetobacter baumannii strains are naturally competent. Although some information is available about factors that enhance or reduce the frequency of transformation of this bacterium, the regulatory elements and mechanisms are barely understood. In this article, we describe studies on the role of H-NS in the regulation of expression of genes related to natural competency and the ability to uptake foreign DNA. The expression levels of the natural transformation-related genes pilA, pilT, pilQ, comEA, comEC, comF, and drpA were significantly increased in a Δhns derivative of Acinetobacter baumannii A118. Complementation of the mutant with a recombinant plasmid harboring hns restored expression levels of six of these genes (pilT remained expressed at high levels) to those of the wild-type strain. The transformation frequency of the A. baumannii A118 Δhns strain was significantly higher than that of the wild-type. Similar, albeit not identical, effects occurred when hns was deleted from the hypervirulent A. baumannii AB5075 strain. Reduction of gene expression in a few cases was not as pronounced as to reach wild-type levels, and expression of comEA was enhanced further. In conclusion, the expression of all seven transformation-related genes was enhanced after deleting hns in A. baumannii A118 and AB5075, and these modifications are accompanied by an increase in the cells’ transformability. The results demonstrate a role of H-NS in A. baumannii’s natural competence.

Introduction: The trophoblast derived angiogenic factors are considered to play an important role in the pathophysiology of various complications of pregnancy. The aim of this study was to establish relationship between concentrations of soluble Human Leukocyte Antigen-G (sHLA-G) in maternal serum and amniotic fluid at 16-22 weeks of gestation and the sonographic measurements of the fetal and placental growth. Materials and methods: sHLA-G in serum and amniotic fluid, as well as fetal biometric data and placental volume and perfusion indices were determined in 41 uncomplicated singleton pregnancies. Results: The sHLA-G levels were unchanged both in amniotic fluid and in serum during mid-pregnancy. The sHLA-G level in serum correlated positively with amniotic sHLA-G level (β=0.63, p<0.01). Significant correlation was found between serum sHLA-G level and abdominal measurement (β=0.41, p<0.05) and estimated fetal weight (β=0.41, p<0.05). The amniotic sHLA-G level and placental perfusion (VI: β = -0.34, p<0.01 and VFI: β = -0.44, p<0.01, respectively) were negatively interrelated. A low amniotic sHLA-G level was significantly associated with nuchal translucency (r = -0.102, p<0.05). Conclusions: sHLA-G assayed in amniotic fluid might be a potential indicator for placental function, whereas the sHLA-G level in serum can be a prognostic modality for feto-placental insufficiency.

External hoof characteristics, balance, and conformation have been extensively studied in horses; however, mules remain understudied in these aspects. This study evaluated the size, shape, and symmetry of untrimmed and unshod forelimb hooves, compared the symmetry between forelimb hooves and stratified external forelimb hoof measurements based on the body condition score of mules raised in the foothill plains of northern Thailand. The forelimb hooves of 38 mules were photographed and 33 parameters, including angular and linear measurements, were analyzed. Despite the absence of shoeing and trimming, these mules exhibited optimal left-right forelimb hoof symmetry, with no significant (p < 0.05) differences in: outer wall length and inner wall length (OWL - IWL); sole length and sole width (SLS - SW); dorsal hoof wall length and heel length (DHWL - HL); and frog length and frog width (FL - FW). However, significant (p < 0.05) differences were observed within each body condition score group for forelimb hoof measurements for DHWL, IWL, heel separation (HS), heel bulb distance (HBD), SW, FW, and FL. These findings provide valuable insights into mule welfare and management, contributing to understanding of the interplay between overall health and hoof conformation in the study area.

Reactions in water between the Cu2(µ-EGTA) chelate (EGTA = ethylene-bis(oxyethyleneimino)tetraacetate(4-) ion) and 2,6-diaminopurine (Hdap) in molar ratios 1:1 and 1:2 yield only blue crystals of the ternary compound [Cu4(μ-EGTA)2(μ-H(N3)dap)2(H2O)2]·7H2O (1) that has been studied by single crystal X-ray diffractometry, various physical methods (thermal stability, spectral and magnetic properties), as well as DFT theoretical calculations. In the crystal, uncoordinated water is disordered. The tetranuclear complex molecule also has some irrelevant disorder in an EGTA-ethylene moiety. In the complex molecule, both bridging organic molecules act as binucleating ligands. There are two distorted five- (type 4+1) and two six- (type 4+1+1) Cu(II) centres. Each half EGTA acts as a tripodal tetradentate Cu(II) chelator, with mer-NO2+O(ether, distal) conformation. Hdap exhibits the tautomer H(N3)dap, with the dissociable H-atom on its less basic N-heterocyclic atom. These features favour the efficient cooperation between Cu-N7 or Cu-N9 bonds with appropriate O-EGTA atoms, as N6-H···O or N3-H···O interligand interactions respectively. Bridging role of both organics determines the tetranuclear dimensionality of the complex in 1. In this crystal, such molecules associate in zig-zag chains, built by alternating ,-interactions between the five- or six-atom rings of Hdap ligands of adjacent molecules. DFT theoretical calculations (using two different theoretical models and characterized by the quantum theory of “atoms in molecules”) reveal the importance of these ,-interactions between Hdap ligands, as well as that corresponding to the referred hydrogen bonds in the contributed tetranuclear molecule.

Today, more than 70 million tons of lignin are produced by the pulp and paper industry every year. However, the utilization of lignin as a source for chemical synthesis is still limited due to the complex and heterogeneous lignin structure. The purpose of this study was a selective photodegradation of industrially available kraft lignin in order to obtain appropriate fragments and building block chemicals for further utilization, e.g. polymerization. Thus, kraft lignin obtained from soft wood black liquor by acidification was dissolved in sodium hydroxide and irradiated at a wavelength of 254 nm with and without the presence of titanium dioxide in various concentrations. Analyses of the irradiated products via SEC showed decreasing molar masses and decreasing polydispersity indices over time. At the end of the irradiation period the lignin was depolymerised to form fragments as small as the lignin monomers. TOC analyses showed minimal mineralisation due to the depolymerisation process.

This paper presents a wideband dual-polarized dipole antenna structure operating at 1.7-3.8 GHz (76.4%). For a traditional 4G dipole antenna which covers the band 1.71 GHz- 2.69 GHz, it’s difficult to maintain the satisfactory impedance matching and normal stable radiation patterns within the 5G sub-6 GHz band 3.3-3.8 GHz, which mainly due to the fixed antenna height is no longer a quarter-wavelength. To solve this, a connected-ring-shaped metasurface structure is proposed and deployed to operate as an artificial magnetic conductor (AMC). As a result, stable antenna radiation patterns are obtained within the whole band 1.7-3.8 GHz. For verification, this wideband dipole antenna using AMC is implemented and tested. The measured results show that the proposed antenna has an impedance bandwidth of 80.7% (1.7-4.0 GHz). It has an average measured in-band realized gain of 7.0±1.0 dBi and a stable 70∘±5∘ half power beam width (HPBW) within the 4G/5G-sub 6GHz bands 1710-2690 MHz and 3300-3800 MHz.

Infections contribute to carcinogenesis through inflammation-related mechanisms. It is well established that H. pylori infection is an etiological factor in gastric carcinogenesis. However, the mechanism through which H. pylori infection contributes to the development of gastric cancer has not been fully elucidated. H. pylori-associated chronic inflammation is linked to genomic instability via reactive oxygen and nitrogen species (RONS). In this article, we summarize the current knowledge of H. pylori-induced double strand breaks (DSBs). Further, we will provide mechanistic insight into how processing of oxidative DNA damage via base excision repair (BER) leads to double strand breaks (DSBs). We review the recent progress how H. pylori infection triggers NF-kB /iNOS versus NF-kB/nucleotide excision repair (NER) axis mediated DSBs to drive genomic instability. Taken together, this review discusses current findings related to DSBs and their implications for the mechanisms of DSB repair.

In this paper we obtain some inequalities of Hermite-Hadamard type for composite convex functions. Applications for AG, AH-h-convex functions, GA, GG, GH-h-convex functions and HA, HG, HH-h-convex function are given.

Retinitis pigmentosa-59 (RP59) is a rare, recessive form of RP, caused by mutations in the gene encoding DHDDS (dehydrodolichyl diphosphate synthase). DHDDS forms a heterotetrameric complex with Nogo-B Receptor (NgBR; gene NUS1) to form a cis-prenyltransferase (CPT) enzyme complex, which is required for synthesis of dolichol, which in turn is required for protein N-glycosylation as well as other glycosylation reactions in eukaryotic cells. Herein, we review the published phenotypic characteristics of RP59 models extant, with an emphasis on their ocular phenotypes, based primarily upon knock-in of known RP59-associated DHDDS mutations as well as cell type- and tissue-specific knockout of DHDDS alleles in mice. We also briefly review findings in RP59 patients with retinal disease and other patients with DHDDS mutations causing epilepsy and other neurologic disease. We discuss these findings in the context of addressing “knowledge gaps” in our current understanding of the underlying pathobiology mechanism of RP59, as well as their potential utility for developing therapeutic interventions to block the onset, or to dampen the severity or progression, of RP59.

Tilapia tilapinevirus, or tilapia lake virus (TiLV), is a virus that has caused disease outbreaks in many countries worldwide since 2009. We recently developed two simple but effective TiLV vaccines based on heat-killed virus (HKV) and formalin-killed virus (FKV). In the present study, we evaluated the immunological response and efficacy of MontanideTM ISA 763A VG oil-based vaccines (O-HKV and O-FKV) in Nile tilapia (Oreochromis niloticus) and compared these responses in fish vaccinated with water-based formulations (W-HKV and W-FKV). Juvenile Nile tilapia were given primary and booster vaccinations with the vaccine formulations. The relative fold change in expression of five immunoglobulin genes (IgM, IgT, IgD, CD4 and CD8) was assessed before and after booster vaccination, and a challenge with TiLV was performed to evaluate the efficacy of the vaccines. The results showed that the water-based vaccines induced higher levels of Ig transcripts and conferred significantly higher levels of protection compared to the oil-based formulations, with relative percent survival (RPS) values ranging from 54.6% to 59.7% for W-HKV and W-FKV vaccinated fish, and 32% and 0% for the O-HKV and O-FKV vaccinated fish, respectively. These findings suggest that water-based vaccines are more effective at protecting tilapia against TiLV infection, and MontanideTM ISA 763A VG may not be a suitable adjuvant for formulating whole-inactivated TiLV vaccines.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

Background Obesity compromises the health of a woman's pregnancy and her newborn. Aim: To describe weight-gaining changes throughout pregnancy and evaluating outcomes for the mother and the baby. Methods A retrospective review of women who delivered singletons using Large Perinatal Registry. According to their BMI, patients were categorized into four categories: underweight, normal, overweight, and obese. Mode of delivery, gestational diabetes, hypertensive diseases, obstetric cholestasis, and postpartum hemorrhage were the main maternal outcome measures. The newborn outcome indicators were birth weight, NICU hospitalization, premature birth, and stillbirth. Results The study sample included 2,352 natives (25%) and 7,058 expatriates (75%). The majority of the sample (4726) were aged 20-29 years, 43.6% were aged 30-39 years, and 2.1% and 3.9% were aged 19 years and 40 years respectively. The incidence of hypertension, obstetric cholestasis, diabetes, postpartum hemorrhage, and cesarean section varied among the entire sample. In the underweight group, the incidence of CS was 15.7%, in the normal weight group (24.9%), in the overweight group (31.3%), and in the obese group (41%). Hypertensive disorders were 3 times more prevalent in obese women than in normal-weight women (2%), and 5.3% of obese women had PPH compared to 5. 6% of women of normal weight. The underweight groups gained the most weight during pregnancy, whereas the obese gained the least. Conclusions A significant proportion of pregnant women in our sample will become obese by the time of delivery. Obesity during pregnancy is associated with negative maternal and fetal outcomes.

The antiradical and antimicrobial activity of lignin and lignin-based films are both of great interest for applications such as food packaging additives. The polyphenol structure of lignin in addition to the presence of O-containing functional groups is potentially responsible for these activities. This study used DPPH assays to discuss the antiradical activity of HPMC/lignin and HPMC/lignin/chitosan films. The scavenging activity (SA) of both binary (HPMC/lignin) and ternary (HPMC/lignin/chitosan) systems was affected by the percentage of the added lignin: the 5% addition showed the highest activity and the 30% addition had the lowest. Both, scavenging activity and antimicrobial activity are depending on the biomass source showing the following trend: organosolv of softwood > Kraft of softwood > organosolv of grass. Testing the antimicrobial activities of lignins and lignin-containing films showed high antimicrobial activities against gram-positive and gram-negative bacteria at 35 °C and at low temperatures (0-7 °C). Purification of kraft lignin has a negative effect on the antimicrobial activity while storage has positive effect. The lignin release in the produced films affected the activity positively and the chitosan addition enhances the activity even more for both gram-positive and gram-negative bacteria. Testing the films against spoilage bacteria that grow at low temperatures revealed the activity of the 30% addition on HPMC/L1 film against both B. thermosphacta and P. fluorescens while L5 was active only against B. thermosphacta. In HPMC/lignin/chitosan films the 5% addition exhibited activity against both B. thermosphacta and P. fluorescens.

Heavy metal contaminants have serious consequences for the environment and human health. Consequently, effective methods for detecting their presence, particularly in water and food, are urgently required. Accordingly, the present study proposes a sensor for the detection of mercury Hg(II) and lead Pb(II) ions using graphene oxide (GO) as a quenching agent and aptamer solu-tion as a reagent. In the proposed device, the aptamer sequences are labeled by FAM and HEX fluorescent dyes, respectively, and are mixed with 500 ppm GO solution in a microfluidic device. The presence of Hg(II) and Pb(II) ions is then detected by measuring the change in the fluores-cence intensity of the GO/aptamer suspension as the aptamer molecules undergo fluorescence resonance energy transfer (FRET). The experimental results show that the aptamer sensors have a linear range of 10~250 nM (i.e., 2.0~50 ppb) for Hg(II) ions and 10~100 nM (i.e., 2.1~20.7 ppb) for Pb(II) ions. Furthermore, the limit of detection is around 2 ppb for both metals, which is signifi-cantly lower than the maximum limits of 6 ppb and 10 ppb prescribed by the World Health Or-ganization (WHO) for Hg(II) and Pb(II) in drinking water, respectively.

Skeletal myogenesis is an intricate process involving the differentiation of progenitor cells into myofibers, which is regulated by actin cytoskeletal dynamics and myogenic transcription factors. Although recent studies have demonstrated the pivotal roles of actin-binding proteins (ABPs) as mechanosensors and signal transducers, the biological significance of WAVE2 (Wiskott-Aldrich syndrome protein family member 2), an ABP essential for actin polymerization, in myogenic differentiation of progenitor cells has not been investigated. Our study provides important insights into the regulatory roles played by WAVE2 in the myocardin-related transcription factor A (MRTFA)-serum response factor (SRF) signaling axis and differentiation of myoblasts. We demonstrate that WAVE2 expression is induced during myogenic differentiation and plays a pivotal role in actin cytoskeletal remodeling in C2C12 myoblasts. Knockdown of WAVE2 in C2C12 cells reduced filamentous actin levels, increased globular actin accumulation, and impaired the nuclear translocation of MRTFA. Furthermore, WAVE2 depletion in myoblasts inhibited the expression and transcriptional activity of SRF and suppressed cell proliferation in myoblasts. Consequently, WAVE2 knockdown suppressed myogenic regulatory factors (i.e., MyoD, MyoG, and SMYD1) expressions, thereby hindering the differentiation of myoblasts. Thus, this study suggests that WAVE2 is essential for myogenic differentiation of progenitor cells by modulating the mechanosensitive MRTFA-SRF axis.

Background. Predisposition to HIV+ is influenced by a wide range of correlated economic, environmental, demographic, social, and behavioral factors. While evidence among a candidate handful have strong evidence, there is lack of a consensus among the vast array of variables measured in large surveys. Methods. We performed a comprehensive data-driven search for correlates of HIV positivity in >600,000 participants of the Demographic and Health Survey (DHS) across 29 sub-Saharan African countries from 2003 to 2017. We associated a total of 7,251 and of 6,288 unique variables with HIV+ in females and males respectively in each of the 50 surveys. We performed a meta-analysis within countries to attain 29 country-specific associations. Results. We identified 344 (5.4% out possible) and 373 (5.1%) associations with HIV+ in males and females, respectively, with robust statistical support. The identified associations are consistent in directionality across countries and sexes. The association sizes among individual correlates and their predictive capability was low to modest, but comparable to established factors. Among the identified associations, variables identifying being head of household among females was identified in 17 countries with a mean odds ratio (OR) of 2.5 (OR range: 1.1-3.5, R² = 0.01). Other common associations were identified with marital status, education, age, and ownership of land or livestock. Conclusions. Our continent-wide search for variables has identified under-recognized variables associated with HIV+ that are consistent across the continent and sex. Many of the association sizes are as high as established risk factors for HIV+, including male circumcision.

Modern Monte-Carlo-based rendering systems still suffer from the computational complexity involved in the generation of noise-free images, making it challenging to synthesize interactive previews. We present a framework suited for rendering such previews of static scenes using a caching technique that builds upon a linkless octree. Our approach allows for memory-efficient storage and constant-time lookup to cache diffuse illumination at multiple hitpoints along the traced paths. Non-diffuse surfaces are dealt with in a hybrid way in order to reconstruct view-dependent illumination while maintaining interactive frame rates. By evaluating the visual fidelity against ground truth sequences and by benchmarking, we show that our approach compares well to low-noise path traced results, but with a greatly reduced computational complexity allowing for interactive frame rates. This way, our caching technique provides a useful tool for global illumination previews and multi-view rendering.

The focus of our study was the changes in the composition of semi-natural dry grasslands in Hungary. Since these valuable habitats were created with the help of humans, their preservation also requires regular treatment. Our mowing experiment aimed to investigate the suppression of the native Calamagrostis epigejos L. Roth. In Hungary, in the Cserhát Mountains, eight permanent plots were mowed twice a year. The vegetation was sampled annually between 2001 and 2011. The effects of mowing were investigated with repeated measures analysis of variance (ANOVA). After 10 years, the C. epigejos cover of the mowed plots decreased significantly, from the initial average of 62.38 to 7.50%. Surprisingly, we also experienced a similar decrease in the control plots. Regular treatment also had a positive effect on the number of species and diversity. Species richness increased continuously in both treatment types, which indicates the combined effect of vegetation succession and treatment. The biomass growth of other Poaceae and Fabaceae species, which are important from a grassland management perspective, was also facilitated by mowing. Our results suggest that long-term in situ experiments and continuous botanical studies are needed to establish a reliable utilization of grasslands.

This paper addresses a mode-dependent state-feedback H∞ control for descriptor hybrid systems, considering both the absence and presence of actuator saturation. Firstly, the necessary and sufficient conditions for the stochastic admissibility criterion with H∞ performance ? of the closed-loop system is proposed. Given the proposed non-convex condition, the author reformulates it into linear matrix inequalities (LMIs). Then, to extend the result to the systems with actuator saturation, the actuator saturated control input is expressed as a linear combination of given state-feedback control input and a virtual control input that remains under the saturation level. To verify this expression, the set invariant condition is also suggested by using the singular mode-dependent Lyapunov function candidate. Therefore, the LMI conditions for the existence of the mode-dependent state-feedback H∞ control and the ellipsoidal shape of invariant set are successfully derived. Two numerical examples demonstrate the effectiveness of the proposed approach in optimizing H∞ performance $\gamma$ and identifying the largest invariant set.

The purpose of this study is to estimate the mean transitioning probabilities from a Healthy state to malaria positive uncomplicated state or to malaria positive severe state. It also classifies the various transitioning probabilities of moving through the various states based on some baseline characteristics. Malaria test results for 2019 over a 12-month period were collected from the University of Ghana school clinic. An H-U model for the study was developed and the transition rates from the cross-sectional data are indicated. With two states Healthy (H) and Uncomplicated (U) forming a state space, there were four possible transitions. The results show that the probability of transitioning from a Healthy state to a malaria positive state is 0.03% while the probability that an individual will remain at Healthy state (H) after the test is 99.73%. It was found that if an individual is already positive and has taken medication the probability that its second test came out negative is 6.45% while the chances that it will remain positive but uncomplicated is 93.55%. The study also showed that in the long run, about 95.98% of persons who visited the student clinic with malaria symptoms recorded negative tests for malaria parasite while about 4% recorded positive for malaria. In terms of disaggregation by gender, it was realized that the number of reported negative test results were higher for females (97.08%) than for males (96.13%). However, the infection rate is higher for males (3.87%) than females (2.92%). It is recommended that in as much as the University of Ghana has two health centers (a clinic and hospital), there should be a centralized system to track students’ health so research done would not be biased.

In this paper, modelling designing and simulation of a Ward Leonard layout system is done using robust control theory. In order to increase the performance of the Ward Leonard layout system with H infinity optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers are used. The open loop response of the Ward Leonard layout system shows that the system needs to be improved. Comparison of the Ward Leonard layout system with H∞ optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers to track a desired step speed input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed Ward Leonard layout system with H infinity optimal control synthesis controller in improving the percentage overshoot and the settling time.

Papain-like lysosomal cysteine proteases include 11 human cysteine cathepsins which act as endopeptidases and/or exopeptidases. They are involved in numerous physiological and pathological processes. Among them, only cathepsins B, H, C, and X/Z exhibit exopeptidase activity. Their activities are tightly regulated in various ways to prevent potentially hazardous effects on the cell. In this review, we focus on the structural and functional aspects of these four cysteine cathepsins and their role in neurodegeneration and cancer. Neurodegenerative disorders of aging share an endolysosomal dysfunction and accumulation and spread of oligomeric forms of neurotoxic proteins. The accumulation of various protein aggregates activates the microglia, thus inducing the activation and release of cysteine cathepsins and proinflammatory cytokines, leading to neurodegeneration. In cancer, cysteine cathepsins participate in tumor progression and metastasis. Tumor–stromal crosstalk leads to activation of the stroma and overexpression and secretion of proteolytic enzymes, triggering extracellular matrix degradation and the release of soluble factors. Activated stromal cells (i.e., macrophages, fibroblasts, mast cells) secrete additional growth factors, cytokines, and chemokines that are responsible for the regulation of processes leading to tumor progression and metastasis. Therefore, a better understanding of the role of cysteine cathepsins in neurodegeneration and cancer could lead to novel targeted therapeutic approaches.

In this paper, the design and control of a hydraulic system based tire changer machine have been analyzed and simulated using Matlab/Simulink Toolbox successfully. The machine have a displacement input which is a leg pedal displacement in order to push the piston of the pump to fed the motor with a pressured hydraulic fluid to rotate the tire with an angular speed to mount and dismount it. Augmentation based H_∞ and H₂ optimal synthesis controllers have been used to improve the performance of the machine. Comparison of the proposed controllers for tracking a reference input speed have been done using two reference inputs (step and random) signals. Finally the comparative simulation results proved the effectiveness of the proposed tire changer with H synthesis controller in improving the settling time and percentage overshoot.

In infectious disease and clinical microbiology, rarely encountered species are often of special concern simply by virtue of their unfamiliarity, especially in settings of complicated underlying disease. This is all the more so when the infectious agent has an appearance that distinguishes it from most commonly encountered organisms, making it a mystery that must be explained. In this context, it is rare for histopathologists to be more familiar with a bacterial species than clinical microbiologists but Sarcina ventriculi is one such example. Infrequently seen in tissue and even less often in culture, we here report a case of Sarcina ventriculi in the GI tract of a geriatric patient with complex underlying history. A brief discussion of the history, clinical presentation, treatment, and culture conditions of this organism is provided, along with clarification of nomenclature, which has changed and could otherwise be a source of additional confusion in this rarely encountered bacterium.

Abstract Background: Metabolic syndrome (MetS) is a complex disorder characterized by insulin resistance (IR), central obesity, atherogenic dyslipidemia and higher glucose levels. It increases the risk of cardiovascular disease (CVD) and type 2 diabetes mellitus (T2DM), imposing an economic burden on the healthcare system. However, the historical origins of MetS as well as the development and evolution of its definitions have not been conclusively documented in the literature. Aim: This study seeks to enhance the understanding of the developmental trends of MetS during the preceding two decades, placing particular emphasis on the definition, diagnosis and prevalence. Methods: An extensive search was performed from 1920 to 2023 across prominent scientific research engines, including Scopus, PubMed, MDPI, and others. Results: Despite advancements, many aspects of MetS remain inadequately understood. As the understanding of the nature and pathophysiology of MetS progresses, the development and refinement of its diagnostic criteria, and assessment and treatment guidelines will continue. Additionally, there exists significant variation in the global prevalence of metabolic syndrome, ranging from 14 to 39%. This prevalence is projected to increase due to the adoption of less healthy dietary patterns and sedentary lifestyles. The observed disparities in metabolic syndrome prevalence can be attributed to multiple factors, including demographic characteristics. Furthermore, the lack of a standardized definition across studies also contributes to the variation in reported prevalence rates. Conclusion: Further studies focusing on the standardization of the MetS definition across different research are crucial. The establishment of consistent criteria would enhance the reliability and validity of research findings, enabling more meaningful comparisons and interpretations.

This study employed a TSMC 0.18-µm 50 V process to establish a high-voltage n-LDMOS structure. In the reference device, the number of floating-poly (poly-2) turns was 7, and the width and spacing of each turn was 1 µm. Although increasing the number of turns reduces the peak field, directly reducing or increasing the number of poly-2 turns is a common practice. The present experiment was realized in three steps, namely fixing the number of occupied area adjustment turns, adjusting the width of each turn, and adjusting the distance between turns. The first step was fixing the number of occupied area adjustment turns. The number of turns was increased from 7 to 9, and the number of turns was reduced to 5 and 3 in the reference group. A reduction in the number of turns led to a greater decrease in the peak field and increase in the breakdown voltage despite the area remaining unchanged. A comparison of the use of three turns with that of seven turns revealed that the maximum electric field decreased by 42%, from 4.17e+3 to 2.46e+3 V/cm, and that the breakdown voltage (VBK) increased from 30.2 to 35.84 V. The second step was adjusting the width of each turn from 1 to 1.4, 1.2, 0.8, and 0.6 µm in the reference group. This increase in width reduced the maximum electric field and led to a greater increase in VBK. When the width was increased to 1.4 µm, the maximum electric field decreased by 29% from 1.95e+3 to 1.4e+3 V/cm, and the VBK increased by 183% from 30.2 to 85.6 V. The third step was adjusting the spacing of each turn from 1 to 1.4, 1.2, 0.8, and 0.6 µm in the reference group. The results revealed that a reduction in the spacing led to a greater reduction in the maximum electric field and an in-crease in the VBK. When the pitch was reduced to 0.6 µm, the maximum electric field decreased by 33%, from 1.95e+3 to 1.32e+3 V/cm, and the VBK increased by 345%, from 30.2 to 134.4 V.

Unmanned aerial vehicles (UAVs) are one of the most promising innovative technologies invented in recent years to promote precision agriculture and smart farming. UAVs can not only reduce labor requirements but also increase production output, reduce the use of pesticides, and protect the environment. However, previous studies on agricultural UAVs have mostly focused on technical problems such as software and hardware design. Few studies have examined users’ behaviors in the implementation process. On the basis of Orlikowski and Gash’s technological frames, this study explored the participants’ cognition and expectation of farmers, pesticide, sprayers, and agriculture officials, who are three key groups of stakeholders involved in the application of UAVs to pesticide spraying, regarding agricultural UAVs and examined how the conflicts between their cognition and expectation influenced the choice of using pesticide spraying UAVs. The conclusions of this study contributed to supplement the content and broaden the scope of application of technological frame theory and provided a crucial reference for the promotion of agricultural UAVs in practice.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

Many corporations have now revised their value statements to showcase their commitment to sustainable development and green business due to the pressing issues of climate and environmental damage. Despite the importance of value statements that can direct companies to achieve sustainable goals, what kind of values can be perceived as organizational orientations to sustainability remains unknown. This study explores how the general public views the inclusion of sustainable components in value statements from the listed companies in Hong Kong by using Q-sort methodology (n = 30). Analyzing the final sample of 40 value statements extracted from 27 listed companies, we identified three factors related to sustainability, namely, Empowering business process management, Empowering customer-centric excellence, and Empowering sustainable progress. This study provides an additional component to the traditional triple bottom line by suggesting that internal operation of a company is an emerging idea to understand corporate sustainability.

The reaction of mercaptoacetic acid esters with pentachloro-2-nitro-1,3-butadiene provides appropriate precursors for the synthesis of 2,3,4-trisubstituted benzo[h]quinolines. These heterocycles are easily accessible via a single-step reaction with 1-naphthyl- or 1-anthracenylamine, respectively. Due to steric bulk and high electron density ring closure to benzo[h]quinolines takes place, exclusively. Such highly substituted annelated pyridine systems can be modified in subsequent, selective reactions to build up new N-heterocycles with promising microbiological properties. Antibacterial and antiproliferative assays against four cell mammalian cell lines demonstrate that some of the sulfur-substituted benzo[h]quinolines analogs display potent phenotypic bioactivities in the single-digit micromolar range.

Hypotrochoidal profile contours have been produced in industrial applications in recent years using twin-spindle processes, and they are considered effective high-quality solutions for positive shaft–hub connections. This study mainly concerns analytical approaches to determine the bending stresses in hypotrochoidal profile shafts. The formulation was developed according to bending principles using the mathematical theory of elasticity and conformal mappings. The loading was further used to investigate the rotating bending behaviour. The stress factors for the classical calculation of maximum bending stresses were also determined for all those profiles presented and compiled in the German standard DIN3689-1 for practical applications. The results were also compared with the corresponding numerical and experimental results, and very good agreement was observed. Additionally, based on previous work, the stress factor was determined for the case of torsional loading to calculate the maximum torsional stresses in the standardised profiles, and the results are listed in a table. This study contributes to the further refinement of the current DIN3689 standard.

This work presented the design and fabrication of blood vessel and breast tumor detection device (BKA-06) based on optical energy spectroscopy. The BKA-06 device uses red-to-near-infrared light-emitting diodes that allow physicians or physicians to visualize blood vessels and surface structures such as breast tumors with the naked eye. The device consisted of built-in current control circuit to have the appropriate brightness (maximum illuminance of 98592 lux) for the examination of superficial tumors deep under the skin, with a scan time of 3-5 minutes. The device BKA-06 could facilely observe each layer of blood vessels at the depth of the skin. For breast tumors, the location, size and invasive areas around the tumor can also be visualized with the naked eye using the BKA-06 sensor. The results show that the BKA-06 sensor can provide clear breast tumor and vascular images with a penetration of up to 15 cm in the skin and tissue layers of the breast. The breast tumor scanning tests with the BKA-06 sensor gave patients quick results and compared them through cell biopsy and MRI respectively. The device has the advantage of being simple, easy to use, providing potential practical applications in the medical field, reducing costs for patients when taking MRI or CT scans. Therefore, the BKA-06 device is expected to help doctors and medical staff overcome difficulties in infusion as well as identify breast tumors to support early breast cancer diagnosis and treatment.

High dietary phosphate intake and poor adherence to phosphate-binding-therapy elevate the risk of hyperphosphatemia in maintenance hemodialysis (HD; MHD) patients. Therefore, chronic kidney disease-related mineral and bone disorder (CKD-MBD) indicators increase; consequently, risks of CKD-MBDs and inflammation are elevated. This double-blind, randomized control trial intervention study was designed to investigate the possibility of reducing blood CKD-MBD indicators and modulating inflammatory indicators by consuming low-phosphate (LP) meals accompanied by a minimum dose of a calcium-based phosphate binder (CaCO3). MHD patients were recruited and randomly assigned to an LP meal group (LP group) or a control group. After initial data collection, blood collection, and dietary counseling, subjects were asked to consume a washout diet for 1 week. During the washout diet period, subjects consumed their usual diet but took 1 tablet of calcium carbonate (1CaCO3) as a phosphate binder with each meal. After the washout diet period, subjects in the LP group and control group respectively consumed LP meals and regular meals twice a day for 1 week. Meat in the LP meals was boiled before the regular cooking process, but meat in control meals was not. All meals were supplied by a central kitchen so that the contents of phosphate and other nutrients could be identified. In total, 40 MHD patients completed the study program. After 1 week of the dietary intervention, the blood Ca x P product and dietary phosphate had significantly decreased in the LP group compared to the control group (p&lt;0.05). The LP group had significantly lower variations in dietary phosphate intake, blood calcium, Ca x P product, and tumor necrosis factor (TNF)-α than the control group by comparing differences between after the dietary intervention and the baseline (△after intervention - baseline, p&lt;0.05). The increase in dietary phosphate intake (△3rd - 2nd dietary phosphate intake) augmented the increase in the TNF-α level by 6.24-fold (odds ratio [95% confidence interval]: 6.24 [1.12~34.92], p&lt;0.05). These results highlighted the conclusion that LP meals accompanied by a minimum dose of CaCO3 downregulated pro-inflammation by reducing CKD-MBD indicators which was triggered by decreasing dietary phosphate intake.

Cervical cancer is one of the ailments that endangers the health of women all over the world and causes infertility. Fortunately, this disease can be avoided. Both the results and participation rates of the current preventative strategy remain poor. Hence, preventative or early detection methods remain challenging and open. In gynecology and computer science fields, few studies on identifying cervical cancer are based on behavior risk factor and machine learning. Moreover, various social and behavioral aspects might often make it more difficult to detect cervical cancer especially in low‑ and middle‑income countries (LMICs). Accordingly, focus on predicting the presence of cervical cancer through behavioral risk factors is the basic structure of this research. We proposed an approach to classify cervical cancer from a social-behavioral perspective using logistic regression to predict cervical cancer. We got significantly improved outcomes than the existing methods. Moreover, we used feature engineering to formulate less dimensionality as a pre-processing step and optimized parameters to be prepared for classification phase. The results proved that using the logistic regression with regularization type L1 had a promising performance. The accuracy of Logistic Regression (LR) L1 was 97.2%. Such results support the proposed work as a reliable classification predictive tool.

Due to the digitization and Internet of Things revolutions, the present electronic world has a wealth of cybersecurity data. Efficiently resolving cyber anomalies and attacks is becoming a growing concern in today's cyber security industry all over the world. Traditional security solutions are insufficient to address contemporary security issues due to the rapid proliferation of many sorts of cyber-attacks and threats. Utilizing artificial intelligence knowledge, especially machine learning technology, is essential to providing a dynamically enhanced, automated, and up-to-date security system through analyzing security data. In this paper, we provide an extensive view of machine learning algorithms, emphasizing how they can be employed for intelligent data analysis and automation in cybersecurity through their potential to extract valuable insights from cyber data. We also explore a number of potential real-world use cases where data-driven intelligence, automation, and decision-making enable next-generation cyber protection that is more proactive than traditional approaches. The future prospects of machine learning in cybersecurity are eventually emphasized based on our study, along with relevant research directions. Overall, our goal is to explore not only the current state of machine learning and relevant methodologies but also their applicability for future cybersecurity breakthroughs.

Artificial Intelligence (AI) is a leading technology of the current age of the Fourth Industrial Revolution (Industry 4.0 or 4IR), with the capability of incorporating human behavior and intelligence into machines or systems. Thus AI-based modeling is the key to building automated, intelligent, and smart systems according to today's needs. To solve real-world issues various types of AI such as analytical, functional, interactive, textual, and visual AI can be applied to enhance the intelligence and capabilities of an application. However, developing an effective AI model is a challenging task due to the dynamic nature and variation in real-world problems and data. In this paper, we present a comprehensive view on "AI-based Modeling" with the principles and capabilities of potential AI techniques that can play an important role in developing intelligent and smart systems in various real-world application areas including business, finance, healthcare, agriculture, smart cities, cybersecurity and many more. We also emphasize and highlight the research issues within the scope of our study. Overall, the goal of this paper is to provide a broad overview of AI-based modeling that can be used as a reference guide by academics and industry people as well as decision-makers in various real-world scenarios and application domains.

Educational institutions must identify students who are academically struggling to provide them with necessary support to improve their performance. In this context, recommendation systems powered by deep learning techniques are vital for detecting and categorizing such students. These systems help students plan their future by uncovering patterns in their historical academic data. This study introduces a new deep learning model designed to classify academically underperforming students in educational settings. The model incorporates a Gated Recurrent Neural Network (GRU) and includes specific neural network features like a dense layer, max-pooling layer, and the ADAM optimization algorithm. The model's training and evaluation were conducted using a dataset comprising 15,165 student assessment records from various academic institutions. The performance of the developed GRU model was benchmarked against other educational recommendation systems, including Recurrent Neural Network models, AdaBoost, and the Artificial Immune Recognition System v2. The proposed GRU model demonstrated remarkable accuracy, achieving an overall rate of 99.70%.

Under the influence of various factors, the bronze ware unearthed by archaeology has various diseases of different degrees, and the mineralization problem is more prominent. The physical properties of mineralized bronzes have been destroyed, and the whole is loose and fragile, which is in urgent need of reinforcement and protection. Common reinforcement and protection materials mainly consider surface sealing, matrix bonding reinforcement and penetration reinforcement. Considering the low matrix strength and complex disease types of fragile bronzeware, it is difficult to achieve targeted protection with commonly used reinforcement and protection materials. In view of the problems such as poor permeability and easy discoloration of commonly used protection materials, this paper uses self-developed reinforcement and protection material AMC to compare its reinforcement and protection performance with B72, which has a high comprehensive evaluation on the performance of commonly used reinforcement and protection materials. The matrix strength was increased, and the appearance intervention degree was less than B72.

: Extra- and intra-cellular activity occurs under the direction of numerous inter-molecular interactions, and in any tissue or cell, molecules are densely packed, thus promoting those molecular interactions. Galectins and chemokines, the focus of this review, are small, protein effector molecules that mediate various cellular functions, in particular cell adhesion and migration, as well as cell signaling/activation. In the past, researchers have reported that combinations of these (and other) effector molecules act separately, yet sometimes in concert, but nevertheless physically apart and via their individual cell receptors. This view that each effector molecule functions independently of the other limits our thinking about functional versatility and cooperation, and, in turn, ignores the prospect of physiologically important inter-molecular interactions, especially when both molecules are present or co-expressed in the same cellular environment. This review is focused on such protein-protein interactions with chemokines and galectins, their homo- and hetero-oligomeric structures that they can form, and the functional consequences of those paired interactions.

Due to the rising dependency on digital technology, cybersecurity has emerged as a more prominent field of research and application that typically focuses on securing devices, networks, systems, data and other resources from various cyber-attacks, threats, risks, damages, or unauthorized access. Artificial Intelligence (AI), also referred to as a crucial technology of the current Fourth Industrial Revolution (Industry 4.0 or 4IR), could be the key to intelligently dealing with these cyber issues. Various forms of AI methodologies, such as analytical, functional, interactive, textual as well as visual AI can be employed to get the desired cyber solutions according to their computational capabilities. However, the dynamic nature and complexity of real-world situations and data gathered from various cyber sources make it challenging nowadays to build an effective AI-based security model. Moreover, defending robustly against adversarial attacks is still an open question in the area. In this paper, we provide a comprehensive view on "Cybersecurity Intelligence and Robustness", emphasizing multi-aspects AI-based modeling and adversarial learning that could lead to addressing diverse issues in various cyber applications areas such as detecting malware or intrusions, zero-day attacks, phishing, data breach, cyberbullying and other cybercrimes. Thus the eventual security modeling process could be automated, intelligent, and robust compared to traditional security systems. We also emphasize and draw attention to the future aspects of cybersecurity intelligence and robustness along with the research direction within the context of our study. Overall, our goal is not only to explore AI-based modeling and pertinent methodologies but also to focus on the resulting model's applicability for securing our digital systems and society.

The digital world has a wealth of data, such as Internet of Things (IoT) data, business data, health data, mobile data, urban data, security data, and many more, in the current age of the Fourth Industrial Revolution (Industry 4.0 or 4IR). Extracting knowledge or useful insights from these data can be used for smart decision-making in various applications domains. In the area of data science, advanced analytics methods including machine learning modeling can provide actionable insights or deeper knowledge about data, which makes the computing process automatic and smart. In this paper, we present a comprehensive view on "Data Science'' including various types of advanced analytics methods that can be applied to enhance the intelligence and capabilities of an application through smart decision-making in different scenarios. We also discuss and summarize ten potential real-world application domains including business, healthcare, cybersecurity, urban and rural data science, and so on by taking into account data-driven smart computing and decision making. Based on this, we finally highlight the challenges and potential research directions within the scope of our study. Overall, this paper aims to serve as a reference point on data science and advanced analytics to the researchers and decision-makers as well as application developers, particularly from the data-driven solution point of view for real-world problems.

Vehicle windshield wiper system increases the driving safety by contributing a clear shot viewing to the driver. In this paper, modelling, designing and simulation of a vehicle windshield wiper system with robust control theory is done successfully. H∞ loop shaping and robust pole placement controllers are used to improve the wiping speed by tracking a reference speed signals. The reference speed signals used in this paper are step and sine wave signals. Comparison of the H∞ loop shaping and robust pole placement controllers based on the two reference signals is done and convincing results have been obtained. Finally the comparative results prove the effectiveness of the proposed H∞ Loop Shaping controller to improve the wiping mechanism for the given two reference signals.

The grid nudging technique is often used in regional climate dynamical downscaling to make the simulated large-scale fields consistent with the driving fields. In this study, we focused on two specific questions about grid nudging: (1) which nudged variable had a larger impact on the downscaling results and (2) what was the “optimal” grid nudging strategy for each nudged variable to achieve better downscaling result during summer over the Chinese mainland. To solve this queries, 41 3-month long simulations for the summer of 2009 and 2010 were performed using the Weather Research and Forecasting model (WRF) to downscale National Centers for Environmental Prediction (NCEP) Final Operational Global Analysis (FNL) data to a 30-km horizontal resolution. The results showed that nudging horizontal wind or temperature had significant influence on the simulation of almost all conventional meteorological elements; nudging water vapor mainly affected the precipitation, humidity, and 500 hPa temperature. Moreover, the optimum nudging scheme varied with simulated regions and layers. As a whole, the optimal nudging time was one hour or three hours for nudging wind, three hours for nudging temperature, and one hour for nudging water vapor. The optimal nudged level was above the planetary boundary layer for almost every nudged variable.

Nanoindentation load-depth (P-h) plots is the basis for determination of mechanical properties of the samples and is especially vital for thin coatings deposited on substrates of various mechanical makeup from amorphous-brittle (borosilicate glass) to Silicon (having different crystallographic texture) to ductile substrates like stainless steel as well other aspects like indenter tip shape. The elastic-plastic response by simulated P-h plots as per modified empirical relations have been presented. The outcomes of this computational studies enlighten the database on the P-h plots for various coating/substrate systems and shall aid in the analysis of experimental P-h plots obtained,

Na⁺/H⁺ exchangers (NHEs) are known to be important regulators of pH in multiple intracellular compartments of eukaryotic cells. Sperm function is especially dependent on changes in pH and thus it has been postulated that NHEs play important roles in regulating the intracellular pH of these cells. For example, in order to achieve fertilization, mature sperm must maintain a basal pH in the male reproductive tract and then alkalize in response to specific signals in the female reproductive tract during the capacitation process. Eight NHE isoforms are expressed in mammalian testis/sperm: NHE1, NHE3, NHE5, NHE8, NHA1, NHA2, NHE10, and NHE11. These NHE isoforms are expressed at varying times during spermatogenesis and localize to different subcellular structures in developing and mature sperm where they contribute to multiple aspects of sperm physiology and male fertility including proper sperm development/morphogenesis, motility, capacitation, and the acrosome reaction. Previous work has provided evidence for NHE3, NHE8, NHA1, NHA2, and NHE10 being critical for male fertility in mice and NHE10 has recently been shown to be essential for male fertility in humans. In this article we review what is known about each NHE isoform expressed in mammalian sperm and discuss the physiological significance of each NHE isoform with respect to male fertility.

A simple undirected graph $\Gamma=(V_\Gamma,E_\Gamma)$ admits an $H$-covering if every edge in $E_\Gamma$ belongs to at least one subgraph of $\Gamma$ that isomorphic to a graph $H$. For any graph $\Gamma$ admitting $H$-covering, a total Labelling $\beta: V_\Gamma \cup E_\Gamma \longrightarrow \{1,2,\dots,p\}$ is called an $H$-irregular total $p$-labelling of $\Gamma$ if every two different subgraphs $H_1$ and $H_2$ of $\Gamma$ isomorphic to $H$ have distinct weights where the weight $w_\beta(K)$ of subgraph $K$ of $\Gamma$ is defined as $w_f(K):=\displaystyle \sum_{v\in V_K} f(v) + \sum_{e\in E_K} f(e)$. The smallest number $p$ for which a graph $\Gamma$ admits an $H$-irregular total $p$-labelling is called the total $H$-irregularity strength of $\Gamma$ and is denoted by $ths(\Gamma)$. In this paper, we determine the total $H$-irregularity strength of edge comb product of two graphs.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

A methodology based on the concepts that arise from Density Functional Theory named Conceptual Density Functional Theory (CDFT) was chosen for the calculation of some global and local reactivity descriptors of the Discodermins A-H family of marine peptides through the consideration of the KID (Koopmans in DFT) technique that was successfully used in previous studies of this kind of molecular systems. The determination of active sites of the studied molecules for different kind of reactivities was achieved by resorting to some CDFT-based descriptors like the Fukui functions as well as the Parr functions derived from Molecular Electron Density Theory (MEDT). A few properties identified with their ability to behave as a drug and the bioactivity of the peptides considered in this examination were acquired by depending on a homology model by studying the correlation with the known bioactivity of related molecules in their interaction with various biological receptors. With the further object of analyzing their bioactivity some parameters of usefulness for future QSAR studies, their predicted biological targets and the the ADME (Absorption, Distribution, Metabolism, and Excretion) parameters related to the Discodermins A-H pharmacokinetics are also reported.

Customs law and procedures are important part of the trade system in Jordan. They regulate the flow of goods across the borders. The purpose of this paper is to examine Jordan's import regime by analyzing customs law, rules of origin, free trade zones, and tariffs reform.

The Jordanian Law of Commercial Agents and Intermediaries No. 28 of 2001 and the Emirati Commercial Agency Law No. 2 of 2010 cover all forms of sale contracts through intermediaries. These Laws provide express restrictions and protective provisions on the conduct by local agents of internal commercial agency activities. However, these statutory protections are granted only to registered agencies conducted by national agents.The Jordanian legislator does not regulate the issue of agency exclusivity, which can constitute a restraint of trade and leads to a state of market monopolization. Courts in Jordan have exclusive jurisdiction in settling disputes arising out of agency agreements. However, this exclusive jurisdiction does not cover unregistered commercial agencies which are treated as enforceable commercial contracts under the general provisions prescribed in the Commercial Code.Under the Jordanian Law the principal cannot terminate the agency agreement at any time, but he can dismiss its renewal upon the expiry of its date without justified grounds. Certain statutory protections provided by the Jordanian laws raise barriers to entry to their national markets. This statutory policy violates the specific commitments made by Jordan with respect to market access and national treatment established by the GATS.