We study the work fluctuations in ergotropic heat engines, namely two-strokes quantum Otto engines where the work stroke is designed to extract the ergotropy (the maximum amount of work by a cyclic unitary evolution) from a couple of quantum systems at canonical equilibrium at two different temperatures, whereas the heat stroke thermalizes back the systems to their respective reservoirs. We provide an exaustive study for the case of two qutrits whose energy levels are equally spaced at two different frequencies by deriving the complete work statistics. By varying the values of temperatures and frequencies, only three kinds of optimal unitary strokes are found: the swap operator U1, an idle swap U2 (where one of the qutrits is regarded as an effective qubit), and a non trivial permutation of energy eigenstates U3, which indeed corresponds to the composition of the two previous unitaries, namely U3 = U2U1. While U1 and U2 are Hermitian (and hence involutions), U3 is not. This point has an impact on the thermodynamic uncertainty relations (TURs) which bound the signal-to-noise ratio of the extracted work in terms of the entropy production. In fact, we show that all TURs derived from a strong detailed fluctuation theorem are violated by the transformation U3.

Tightly regulated and robust mitochondrial activities are critical for normal hearing. Previously, we demonstrated that Fus1 KO mice with mitochondrial dysfunction exhibit premature hearing loss. Molecular analysis of the cochlea revealed hyperactivation of the mTOR pathway, oxidative stress, altered mitochondrial morphology and quantity, suggesting compromised energy sensing and production. Here, we investigated whether pharmacological modulation of metabolic pathways using rapamycin (RAPA) or 2-deoxy-D-glucose (2-DG) supplementation can protect against hearing loss in female Fus1 KO mice. Additionally, we aimed to identify mitochondria- and Fus1-dependent molecular pathways and processes critical for hearing. We found that inhibiting mTOR or activating alternative mitochondrial energetic pathways to glycolysis protected hearing in the mice. Comparative gene expression analysis revealed dysregulation of critical biological processes in the KO cochlea, including mitochondrial metabolism, neural and immune responses, and cochlear hypothalamic–pituitary–adrenal axis signaling system. RAPA and 2-DG mostly normalized these processes, although some genes showed a drug-specific response or no response at all. Interestingly, both drugs resulted in a pronounced upregulation of critical hearing-related genes not altered in the non-treated KO cochlea, including cytoskeletal and motor proteins, and Ca2+-linked transporters and voltage-gated channels. These findings suggest that pharmacological modulation of mitochondrial metabolism and bioenergetics may restore and activate processes critical for hearing, thereby protecting against hearing loss

The aim of the present trial was to evaluate the growth performance of buffalo calves fed diets characterized by different forage/concentrate ratio with or without the Saccharomyces Cerevisiae supplementation (CBS 493.94, Yea-Sacc®). Twenty-four male buffalo calves (mean age 145.1 ± 16.1 days; mean weight 108.0 ± 18.7) were assigned randomly to 4 groups, homogeneous for age, fed four different diets: diet 1 F:C ratio 50:50; diet 2 F:C ratio 30:70; diet 3 F:C ratio 50:50 + Yea-Sacc® and diet 4 F:C ratio 30:70 + Yea-Sacc®. Buffalo calves were individually weighted before the start of the experiment and the data were used as a covariate, monthly until the end of the trial. Dry matter intake (DMI), daily weight gain (DWG) and feed conversion ratio (FCR) were calculated. The differences in diets’ composition significantly (p

Candida spondylodiscitis (CS) is a rare disease, for which therapeutic option are limited to fluconazole or echinocandins and the treatment should be administered up to 12 months. In case of reduced azole susceptibility, there is a scarcity of therapeutic options with adequate bone penetration and limited toxicity. We report the first case of successful use of rezafungin for a spondylodiscitis due to Candida parapsilosis with reduced susceptibility to azoles. The patient, affected by paraplegia and short bowel syndrome, was diagnosed with CS with culture on vertebral biopsy guided by a 18-FDG-PET/CT scan. He received rezafungin 200 mg weekly for 26 weeks, after 10 weeks of previous antifungal treatment. He had a full clinical, radiologic and biochemical response to the therapy with rezafungin, with no adverse effects. Rezafungin is a promising therapy for Candida osteomyelitis, especially when first line therapies are ineffective or contraindicated.

The incremental sheet forming represents a relatively recent technology that guarantees high customization, thanks to the layered manufacturing principle typical of rapid prototyping, and cost-effectiveness, because it does not require dedicated equipment. Research has initially shown that this process is effective in metal materials capable of withstanding plastic deformation but, in recent years, the interest in this technique has been increasing for the manufacture of complex polymer sheet components as an alternative to the conventional technologies, based on heating-shaping-cooling manufacturing routes. Conversely, incremental formed polymer sheets can suffer from some peculiar defects, for example twisting. To reduce the risk of this phenomenon and the occurrence of failures, a viable way is to choose toolpath strategies that make the tool/sheet contact conditions less severe, and this represents the main goal of the present research. Polycarbonate sheets were worked by incremental forming; in detail, cone frusta with a fixed wall angle were manufactured with a reference and a stair toolpath strategy, and both the forming forces and the twist angle were monitored. The analysis of the results highlighted that a stair toolpath involving an alternation of diagonal up and vertical down steps represents a useful strategy to mitigate the forming forces and, with them, the occurrence of the twisting phenomenon in incremental formed thermoplastic sheets.

Atrial fibrillation (AF) is an increasingly recognized comorbidity in patients with cancer. Indeed, cancer patients have a significantly higher incidence of AF than that observed in the general population. A reciprocal relationship between these two diseases has been observed, as much as some assume AF as a marker for occult cancer screening, especially in older adults. The pathophysiological mechanisms are many and varied, including the underlying pro-inflammatory state, specific treatments (chemo and radiotherapy) and surgery. The therapeutic management of patients with cancer and AF involves the same rhythm and frequency control strategies as the general population; however, the numerous interactions with chemotherapeutics, which lead to a significant increase in side effects, as well as the extreme fragility of the patient should be considered. Anticoagulant therapy is also a complex challenge to address, as bleeding and stroke risk scores have not been fully assessed in this subpopulation. Furthermore, in large studies establishing the efficacy of direct oral anticoagulants (DOACs), cancer patients have been underrepresented. In this review, we elaborate on mechanisms linking AF to cancer patients with a particular focus on therapeutic challenges in this population.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

Purpose Prospective life cycle assessment (pLCA) is a key method for providing environmental decision support for future technologies. The specific technology under study is often modeled by the practitioner (the so-called foreground system), whereas data for supply chains are sourced from life cycle inventory databases (the so-called background system). Within pLCA, it is paramount to consider possible future developments for both foreground and background systems to avoid a temporal mismatch between the specific technology under study and the wider economy, which could lead to incorrect conclusions. Therefore, and given the importance of future-oriented environmental decision support, efforts to develop prospective life cycle inventory (pLCI) databases have recently increased. However, there is still much to be improved to realize the widespread use of these databases and to have a stronger real-world effect on how future technology is designed. Methods This paper summarizes recent developments and structures the information chain behind pLCI databases. We then discuss conditions for the broad application of pLCI databases, and we propose priorities and ways forward to overcome existing challenges to foster the use of pLCI databases. Results The conditions are scientific integrity, usefulness to LCA practitioners, accessibility, usability, interpretability, and a continuous improvement process in which core stakeholders coordinate efforts to streamline the generation, sharing, and use of pLCI databases. Conclusions Priority should be given to installing a continuous process to improve the coverage and consistency of pLCI databases, to improve related guidance and documentation, and to remove practical barriers relating to the access and usability of pLCI databases in LCA software.

Atrial fibrillation (AF) is an increasingly recognized comorbidity in patients with can-cer. Indeed, cancer patients have a significantly higher incidence of AF than that ob-served in the general population. A reciprocal relationship between these two diseases has been observed, as much as some assume AF as a marker for occult cancer screen-ing, especially in older adults. The pathophysiological mechanisms are many and var-ied, including the underlying pro-inflammatory state, specific treatments (chemo and radiotherapy) and surgery. The therapeutic management of patients with cancer and AF involves the same rhythm and frequency control strategies as the general popula-tion; however, the numerous interactions with chemotherapeutics, which lead to a sig-nificant increase in side effects, as well as the extreme fragility of the patient should be considered. Anticoagulant therapy is also a complex challenge to address, as bleeding and stroke risk scores have not been fully assessed in this subpopulation. Furthermore, in large studies establishing the efficacy of direct oral anticoagulants (DOACs), cancer patients have been underrepresented. In this review, we elaborate on mechanisms linking AF to cancer patients with a particular focus on therapeutic challenges in this population.

The possibility to test a radio frequency transceiver through the use of appropriate channel emulators allows to evaluate their performance under various operating conditions. Many systems are able to operate with a relatively limited instantaneous bandwidth by applying known statistical models. Sometimes it is necessary to evaluate the performance of a RF transceiver installed on high or very high speed platforms over predictable trajectories using optionally DEMs (Digital Elevation Models)data of the terrain to estimate the number of stimulated paths and their contributions during the flight. When the instantaneous bandwidth of the signal becomes high (over several hundred of MHz), one of the most important phenomenon to consider is the Doppler spread induced by the channel and traditional narrowband models become unuseful. In this paper there are presented some results when a time expansion is adopted in order to emulate the transceiver dynamic and the consequent Doppler spread with the aim to control the spectral purity of the emulated propagation channel.

The Volturno Plain is one of the largest alluvial plain of peninsular Italy. This area is characterized by both natural and human induced subsidence, and is and most susceptible to coastal hazards. The present study is based on post-processing, analysis and mapping of the available Persistent Scatterer interferometry datasets, derived from combination of both ascending and descending orbits of three different SAR satellite systems, during an observation period of almost two decades (June 1992 - September 2010). The main output of the research work is a map of the vertical deformation that provides new insights into the areal variability of ground deformation processes (subsidence/uplift) of Volturno plain over the last decades. Vertical displacement values derived by interferometric data post-processing show that the Volturno river plain is characterized by significant subsidence in the central axial sectors and in the river mouth area, whereas moderate uplift is detected in the eastern part of the plain. Other sectors of the study area are characterized by moderate subsidence and/or stability. We infer that the subsidence recorded in the Volturno plain is mainly a consequence of a natural process related to the compaction of the fluvial deposits that fill up the alluvial plain. Anthropic influence (e.g. water exploitation, urbanization) can be substantially regarded as an additional factor that only locally may enhance subsidence. The uplift imaged in the eastern sector of the plain can be related to tectonic activity. The study of subsidence in the Volturno plain is a valuable tool relevant for river flood analyses and coastal inundation hazard assessment addressed to risk mitigation.

Obsessive–compulsive disorder (OCD) is believed to follow a waxing and waning course, often according to environmental stressors. During the COVID-19 pandemic, pre-existing OCD symptoms were reported to increase and to change from checking to washing behaviors, while new-onset symptoms were predominantly of the hoarding type. In the present study, we followed the evolution of OCD symptoms, anxiety, depression, and insight of illness in forty-six OCD patients throughout the pandemic. Clinical measures were collected at four different time points before and during the COVID-19 pandemic in Italy. Within-subject comparisons were used to compare clinical scale scores across time, and correlations were examined between patients' baseline characteristics and changes in clinical scores. We found that all clinical measures increased during the first Italian lockdown, with respect to the pre-pandemic values. Anxiety decreased during the temporary elimination of restriction provisions, whereas severity of OCD symptoms and insight returned to pre-pandemic values during the second mandatory lockdown. These results were observed only in two sub-groups of patients: those taking benzodiazepines and those with shorter illness duration. Our findings suggest the need of additional clinical attention to these specific sub-groups of OCD patients in case of particularly distressing circumstances, while pointing to a possible adaptive role of their OCD symptoms when the environment requires a higher care of hygiene and extraordinary supply of essential resources.

A novel characterization method for discrete saw filters vibrational sensitivity is presented. The proposed approach allows the characterization of filters under vibrations and the extraction of a behavioural model. Filters are assumed to be transducers so that external induced vibrational energy is partially transformed in a undesired simultaneous amplitude and phase modulation of the input RF signal. When the filter is mechanically excited with vibrations, it introduces spurious amplitude and phase modulation to the input signal that can potentially affect the link quality.

while enjoying a relative positive revival in the digital age, Esperanto and the assessment of its language vitality is often problematic and prone to gross errors, and therefore a theoretical re-flection is required. Unlike other lesser-used languages, Esperanto is intergenerationally trans-mitted mainly outside the family, and so Fishman’s GIDS and subsequent scales such as the EGIDS cannot be applied straightforwardly for language vitality diagnosis and estimation. In particular, it is the social movement with its language activists who guarantee its vitality and developing, for more than a century. A key aspect is the digital domain, where the relatively good positioning of Esperanto does not reflect in a parallel increase in the number of activists. This paper critically assesses the digital language vitality of Esperanto on the basis of its language ide-ology and other sociolinguistic data as a starting point for a discussion to overcome the limits of Blanke’s (2006) scale of language vitality of Esperanto and its rivals. This assessment eventually leads to a more general reflection on the role of ‘coolification’, i.e., the positive effects on language attitudes and development thanks to digital visibility, its limits and the issue of placing it in the context of language vitality in general.

Background: Calcaneal fractures are the most frequent traumatic injuries of the hindfoot and can cause severe disability with social and economic sequelae; since 1980 an increasing number of studies and new technologies have led to an improvement in their management and complications but treatment is still controversial. The purpose of the study to review the secondary scientific literature looking for the optimal management of calcaneal fracture; Methods: through the PubMed MEDLINE database, 4856 articles were identified; only meta-analyses and systematic reviews were included in the study. Results: 59 reviews with more than 10,000 calcaneus fractures were examined and results were divided into various topics; the majority of articles agree on the superiority of surgical versus conservative treatment; minimally invasive access to the sinus tarsi shows better results and fewer complications than traditional extended lateral access; reduction and osteosynthesis with percutaneous and/or minimally invasive techniques seem to provide better outcomes if compared to open treatments. Conclusions: The management of calcaneus fractures requires an individualized planning based on the functional demands of the patient, the type of fracture and associated injuries. New technologies and further studies may still improve the management of these lesions.

In the conservation of monumental heritage, the collection and utilization of information are of primary importance. The Heritage Building Information Modeling (HBIM) procedure harnesses the potential of three-dimensional models, offering significant advantages in accessing documentation, interoperability, multidimensionality of intervention design, cost evaluation and maintenance management. Attention here is focused on the Certosa di Pisa, a large historical complex built in the 14th century as a monastery of the Carthusian order, currently in a state of deterioration and in need of restoration and re-functionalization. The multifaceted nature of this monumental complex, with its intricate interplay of architectural elements spanning different historical periods and featuring diverse techniques, poses a significant challenge for structural safety assessment. This case study presents an opportunity to explore an HBIM approach to streamline the diagnostic process and facilitate the intervention design phase. The goal is achieved by utilizing an accurate 3D model enriched with data from multiple sources and automating certain operations for structural assessment. The usefulness of the HBIM methodology is highlighted as a valuable tool in the realm of Cultural Heritage structures for both technicians and scholars alike.

Background and Objectives: Chronic pain is a prevalent condition that is frequently complicated by mood and anxiety disorders. Purpose of the present article is to identify differences in the management of patients with chronic pain and anxiety/mood disorders depending on the physiotherapists’ gender. Materials and Methods: An ad-hoc questionnaire was developed and sent to 327 physiotherapists by e-mail. The two groups identified by gender were compared by unpaired sample t tests for continuous variables and χ2 tests for qualitative ones. A binary logistic regression was then performed with factors resulted statistically significant at univariate analyses as independent variables and gender as dependent one. Results: Female physiotherapists exhibited a higher level of confidence than male physiotherapists in administering continued physiotherapy for patients affected by Generalized Anxiety Disorder (GAD) (p=0.01), as well as for individuals who had previously engaged with a mental health professional (p=0.01). Furthermore, female physiotherapists believed that pharmacotherapy was less associated with motor side effects (p<0.01) and more frequently recognized the importance of a training to identify affective disorders (p=0.01) and the need of more education in mental health (p=0.01). The binary logistic regression model confirmed that female professionals were less likely to work as freelance (p=0.015) and were more confident in the prosecution of physiotherapy by patients with GAD (p=0.05). Conclusions: Female physiotherapists compared to male ones seem to be more comfortable with patients affected by mental conditions and to be more aware of the need of training on mental health. Further studies are needed to confirm the results of the present study.

The seasonal variation in fatty acids and minerals concentrations was investigated through the analysis of Pecorino Romano cheese samples collected in January, April, and June. A fraction of samples contained missing values in their fatty acid profile. Probabilistic Principal component analysis coupled with Linear Discriminant Analysis was employed to classify cheese samples on a production season basis while accounting for missing data and quantifying the missing Fatty acids concentration for the sample in which they were absent. The levels of rumenic acid, vac-cenic acid and omega-3 compounds were positively correlated with the spring season, while the length of the saturated fatty acids increased throughout the production seasons. Concerning the classification performances, the optimal number of principal components (i.e., 5) achieved an ac-curacy in cross-validation equal to 98 %. Then, when the model was tasked to impute the lacking Fatty acid concentration values, the optimal number of principal components resulted in an R2 value in cross-validation of 99.53%

The goal of clustering is to identify common structures in a data set by forming groups of homogeneous objects. The observed characteristics of many economic time series motivated the development of classes of distributions that can accommodate properties such as heavy tails and skewness. Thanks to its flexibility, the Skewed Exponential Power Distribution (also called Skewed Generalized Error Distribution) ensures a unified and general framework for clustering possibly skewed and heavy tailed time series. This paper develops a clustering procedure of model-based type, assuming that the time series are generated by the same underlying probability distribution but with different parameters. Moreover, we propose to optimally combine the estimated parameters to form the clusters with an entropy weighing $k$-means approach. The usefulness of the proposal is showed by means of application to financial time series, demonstrating also how the obtained clusters can be used to form portfolio of stocks.

Longevity risk constitutes an important risk factor for life insurance companies and it can be managed through longevity-linked securities. The market of longevity-linked securities is at present far from being complete and does not allow to find a unique pricing measure. We propose a method to estimate the maximum market price of longevity risk depending on the risk margin implicit within the calculation of the technical provisions as defined by Solvency II. The maximum price of longevity risk is determined for a survivor forward (S-forward), an agreement between two counterparties to exchange at maturity a fixed survival-dependent payment for a payment depending on the realized survival of a given cohort of individuals. The maximum prices determined for the S-forwards can be used to price other longevity-linked securities, such as q-forwards. The Cairns-Blake-Dowd model is used to represent the evolution of mortality over time, that combined with the information on the risk margin, enables us to calculate upper limits for the risk-adjusted survival probabilities, the market price of longevity risk and the S-forward prices. Numerical results can be extended for the pricing of other longevity-linked securities.

The COVID-19-medical emergency has ended worldwide, yet there is still a need to evaluate the psychological impact of these years of unprecedented changes on students’ life. Methods: This study aims to assess and compare COVID-19-related stressors (Relationships-and-Academic-Life; Isolation; Fear-of-Contagion) and psychophysical symptoms reported by university students in April-2020, April 2021, and April 2022. The predictive role of COVID-19-related stressors on psychophysical symptoms within each time was also tested. Data were collected among 637 university students in April-2020 (n = 197), April-2021 (n = 200), April-2022 (n = 240). Results: In April-2022, perceived Isolation and Fear-of-Contagion decreased from the peak registered in April-2021, but stress related to Relationships-and-Academic-Life remained noteworthy high. A sharp and ongoing increase in psychophysical symptoms was found, with more than 50% of students reporting clinical levels of Sleep-Disorders, Depression, Psychoticism, and Interpersonal-Sensitivity. In April-2022, students still perceiving stress related to Relationships-and-Academic-Life and Isolation were at risk for Anxiety, Somatization, and Sleep-Disorders, while those still perceiving stress related to Fear-of-Contagion were also at risk for Depression, Obsessive-Compulsive, and Psychoticism. Conclusion: Findings emphasized the long-lasting detrimental effects of the COVID-19-related stress. Interventions must pinpoint the complex post-pandemic adjustment process and their effects on university students' psychophysical health.

The stochastic modelling of chemical physical processes is essentially based on a coarse-grained formulation of fluctuations, usually described by means of Wiener processes. By taking the paradigmatic example of chemical reaction kinetics, we propose a simple representation of microscopic stochastic dynamics grounded on the use of distributional derivatives of counting processes that account for elementary reactive events. This approach is consistent with the statistical analysis based on the Chemical Master Equation, and provides the formal setting for the existing algorithmic approaches (Gillespie algorithm). Some practical advantages of this formulation are addressed, and several other examples are discussed in connection with cluster formation, velocity fluctuations in liquid systems, and quantum transitions (radiative interactions) at the molecular level.

Beyond factors such as smoking and obesity, the risk of getting gastrointestinal cancer is passed down from parents to offspring, inherited by a gene mutation, predisposing them to develop cancer in their lifetime. Here we describe the clinical history of family members affected by gastrointestinal pathologies often leading to cancer. In the epidemiological study, the cohort of members of this family shared a high risk of developing gastrointestinal diseases. The subjects were monitored from May 2006 to December 2017 by collecting periodically clinical and endoscopic data, and determining both auto-modification of lymphocyte Poly(ADP-ribose)Polymerase as early signal of DNA damage, and erythrocyte membrane lipid composition (Fat Profile). Both biomarkers were demonstrated to be non invasive and easy tools, to monitor over time family members, first the oldest members (nine siblings), and thereafter their offspring, whose cell status evolved from physiological even to cancerous one. All subjects developed gastrointestinal pathologies of different kind and seriousness. Some diseases evolved to cancer, sometimes as a sudden and lethal event. The results of the two molecular approaches, agreed and even predicted the clinical and imaging paths. This cohort study supported the hypothesis that both noninvasive molecular analyses can predict altered cell states and support clinical and imaging tests.

The study of complex systems deals with emergent behaviour that arises as a result of nonlinear spatio-temporal interactions between a large number of components both within the system, as well as between the system and its environment. There is a strong case to be made that neural systems as well as their emergent behaviour and disorders, can be studied within the framework of complexity science. In particular, the field of neuroimaging has begun to apply both theoretical and experimental procedures originating in complexity science – usually in parallel with traditional methodologies. Here, we demonstrate that the use of such traditional models may distort the outcomes of neuroimaging experiments – hence affecting their interpretability and raising questions about their reliability.Therefore, we argue in favor of adopting a complex systems-based methodology in the study of neuroimaging, alongside appropriate experimental paradigms, and with minimal influences from non-complex systems approaches. Our exposition includes a review of the fundamental mathematical concepts, combined with practical examples and a compilation of results from the literature.

The novel respiratory disease COVID-19 has reached the status of worldwide pandemic and large efforts are currently being undertaken in molecularly characterizing the virus causing it, SARS-CoV-2. The genomic variability of SARS-CoV-2 specimens scattered across the globe can underly geographically specific etiological effects. In the present study, we gather the 48,635 SARS-CoV-2 complete genomes currently available thanks to the collection endeavor of the GISAID consortium and thousands of contributing laboratories. We analyze and annotate all SARS-CoV-2 mutations compared with the reference Wuhan genome NC_045512.2, observing an average of 7.23 mutations per sample. Our analysis shows the prevalence of single nucleotide transitions as the major mutational type across the world. There exist at least three clades characterized by geographic and genomic specificity. In particular, the clade G, prevalent in Europe, carries a D614G mutation in the Spike protein, which is responsible for the initial interaction of the virus with the host human cell. Our analysis may drive local modulation of antiviral strategies based on the molecular specificities of this novel virus.

Silybin is a natural compound extensively studied for its hepatoprotective, neuroprotective and anti-cancer properties. Envisioning the enhancement of silybin potential by suitable modifications in its chemical structure, here, a series of new 7-O alkyl silybins derivatives were synthesized by Mitsunobu reaction starting from the silybins and tyrosol-based phenols, such as tyrosol (TYR, 3), 3-methoxytyrosol (MTYR, 4) and 3-hydroxytyrosol (HTYR, 5). This research sought to explore the antioxidant and anticancer properties of new eighteen derivatives and their mechanisms. In particular, the antioxidant properties of new derivatives outlined by DPPH assay, showed a very pronounced activity depending on the tyrosyl moiety (HTYR>MTYR>>TYR). A significant contribution of the HTYR moiety was observed for silybins and 2,3-dehydro-silybin based derivatives. According to the very potent antioxidant activity, 2,3-dehydro-silybin derivatives 15ab, 15a and 15b exerted the most potent anticancer activity in human prostate cancer PC-3 cells. Furthermore, flow cytometric analysis for cell cycle and apoptosis revealed that 15ab, 15a and 15b induce strong G1 phase arrest and increase late apoptotic population in PC-3 cells. Additionally, western blotting for apoptotic marker cleaved caspase-3 confirmed apoptosis induction by these silybin derivatives in PC-3 cells. These findings hold significant importance in the investigation of anticancer properties of silybin derivatives and strongly encourage swift investigation in pre-clinical models and clinical trials.

The product is a centrifugal air extractor, whose objective is to extract the stale air of SARS-CoV-2 or Covid-19 (Coronavirus); designed for civil and commercial use, it works with a single-phase alternating current (AC) motor of 220 (V) and 50 (Hz), with high energy efficiency (EE). Developed under the Design Thinking methodology, by electromechanical simulation using NI Multisim 14.0 software, case design using Cfturbo 2020 R2.0 CAD software, and rapid 3D prototyping with the OverLord Pro printer; with a prototype of the conventional stator winding of a synchronous motor with a two-pole PMSM/IPM single-phase alternating current (AC) field winding and a 4000 (Gauss) ferromagnetic ceramic magnet rotor. Innovating online nº 15 of invention patent nº 381968 by Nikola Tesla, 5/1/1888.One of the objectives is to link the middle level or Technical Schools with the University system (and careers with a Technological profile) through Project B374 located in the Secretariat of Science and Technology (SCyT) of the National University of La Plata ( UNLP), whose title is: “Integrated Management of Design and Innovation. Contributions for a theoretical-conceptual and methodological review” by the Director: Mg. Federico del Giorgio Solfa. Just as links were sought with the Research and Development Laboratory of the Department of Industrial Design (LIDDI-FBA-UNLP) through its Director D.I. Pablo Ungaro and D.I. Ana Bocos. In 2021, the project participated in the INNOVAR National Contest of the Ministry of Science, Technology and Productive Innovation of the Nation (MINCYT), Argentine Republic; in the "Covid-19 Projects" category, having been selected in the catalog of innovative products, won the 1st. "Covid-19 Projects" position of the National Agency for Research and Technological Development and local innovation (R+D+i) dependent on MINCYT.The results showed, according to the analysis of the test bench, that the PMSM/IPM type synchronous motor used in the centrifugal fan, with the innovation of the reactance-inductive control in series plus the capacitor in parallel, reduces the power by 67% (Watts) and active energy consumption (kWh), performing 56% more mechanical work (Joules) on the fluid air (with a 50% reduction in carbon footprint). Which leads us to the following conclusion: it is possible to develop centrifugal fans that save electricity (kWh) without the need to resort to (1) the "Fan Affinity Law", nor (2) the use of variable speed drives (VDF) or frequency (which are devices with complex and expensive electronics). Which would bring an enormous saving of the cost of electrical energy.

In this paper, we consider a pursuit-evasion game of inertial players, where pursuer’s control is subject to integral constraint, and evader’s control is subject to geometric constraint. In the pursuit problem, the main tool is the strategy of parallel pursuit. Sufficient conditions are obtained for the solvability of pursuit-evasion problems. Also, the main lemma describing the monotonicity of an attainability domain of the evader is proved and an explicit analytical formula for this domain is given. As one of the important results of our paper, the Isaacs Life-line game is solved for a special case.

Background: Military pilots show high visuo-spatial skills. Previous studies demonstrate that they are better in mental rotating a target, in taking different perspectives, in estimating distances, in travel planning and in topographic memory. Here, we compared navigational cognitive styles between military pilots and people without flight experience. Pilots were expected to be more survey users than non-pilots, showing higher navigational strategies. Method: 106 jet military pilots of Italian Air Force and 92 non-pilots were enrolled in order to investigate group differences in navigational styles. Participants were asked to perform a reduced version of the Spatial Cognitive Style Test – SCST, consisting of six tasks that allow to distinguish individuals in landmark (people orient themselves by using a figurative memory for environmental objects), route (people use an egocentric representation of the space) and survey (people have a map-like representation of the space) users. Results: In line with our hypothesis, military pilots mainly adopt a survey style, whereas non-pilots mainly adopt the route style. In addition, pilots outperformed non pilots in both the 3D-Rotation task and Map Description Task. Conclusion: Military flight expertise influences some aspects of the spatial ability, leading to enhance human navigation. Although, it must be considered that they are a population whose navigational skills were already high at the time of selection at the academy before formal training began.

The article takes the case of the adoption of machine learning in a steel manufacturing process through a platform provided by a novel Canadian startup, Canvass Analytics. This way the steel company could optimize the process in a blast furnace. The content of the paper includes a conceptual framework on key factors around steel manufacturing and machine learning. Method: The article takes the case of the adoption of machine learning in a steel manufacturing process through a platform provided by a novel Canadian startup, Canvass Analytics. This way the steel company could optimize the process in a blast furnace. The content of the paper includes a conceptual framework on key factors around steel manufacturing and machine learning. Results: This case is relevant for the authors by the way the business model proposed by the startup attempts to democratize Artificial Intelligence and Machine Learning in industrial environments. This way the startup delivers value to facilitate traditional industries to obtain better operational results, and contribute to a better use of resources. Conclusion: This work is focused on opportunities that arise around Artificial Intelligence as a driver for new business and operating models. Besides the paper looks into the framework of the adoption of Artificial Intelligence and Machine Learning in a traditional industrial environment towards a smart manufacturing approach.

Glycine in its neutral form can exist in the gas phase while its zwitterion form is more stable in water solution.But how many waters are actually necessary to stabilize the zwitterionic structure in the gas phase? Are the intramolecular isotropic spin spin coupling constants sensitive enough to accuse the change in the environment? or the conformer observed? These and related questions have been investigated by a computational study at the level of density functional theory employing the B3LYP functional and the 6-31++G**-J basis set. We found that at least two water molecules explicitly accounted in the super-molecule structure are necessary to stabilize both conformers of glycine within a water polarizable continuum model. At least half of the SSCC’s of both conformers are very stable to changes in the environment and at least four of them differ significantly between Neutral and Zwitterion conformation.

Microplastics are widespread in freshwater environments and could impact these ecosystems. Bivalves are freshwater organisms that are particularly exposed to microplastic contamination. Therefore, in this preliminary study, the accumulation of microplastics, plasticizers, and additives in the freshwater bivalves Anodonta cygnea through active biomonitoring was investigated. Specimens commercially bought were exposed in three rivers in Central Italy for different exposure times: short (1 month) and long (3 months). The gills and the gastrointestinal tract (GIT) were analyzed separately to evaluate the possible uptake and ingestion of particles via Micro-FTIR. For the first time, small microplastics (SMPs, 5-100 µm), plasticizers, additives, and other micro-litter components, e.g., natural and non-plastic synthetic fibers (APFs) were identified in the bivalve A. cygnea. The most abundant polymer in the gills (94.4%), and GITs (66.1%) was polyamide, which had the highest concentration in each river. A decrease in SMPs' abundance was observed over time in the gills in each river, while the abundance in GIT increased. Compared to polymers, a greater variety of APFs was observed in rivers. The APFs changed during the time of exposure and between different rivers more evidently than polymers, allowing a clearer identification of the possible sources. These results highlighted plastic pollution by SMPs using freshwater bivalves as sentinel organisms and the need to investigate further the additives that can be proxies of the presence of microplastics in the environment and biota.

A technique devised some years ago permits to study a theory in a regime of strong perturbations. This translate into a gradient expansion that, at the leading order, can recover the BKL solution. We solve exactly the leading order equations in a spherical symmetric case and we show that the 4-velocity in such a case is multiplied by an exponential warp factor when the perturbation is properly applied. This factor is always greater than one. We will give a closed form solution of this factor for a simple case. Some numerical examples are also given.

Starting from the analysis of the lack of positivity of the Cattaneo heat equation, the article addresses the thermodynamic relevance of the positivity constraint in irreversible thermodynamics, than is at least as important as the entropic constraints. The fulfillment of this condition in hyperbolic models leads to the parametrization of the concentration fields with respect to internal variables associated with the microscopic dynamics. Using Brownian motion theory as a landmarking example for deriving macroscopic transport equations from the equations of motion at the particle/molecular level, we discuss two typical problems involving hydrodynamic interactions at microscale: surface chemical reactions at a solid interface of a diffusing reactant, and mass-balance equations in a complex viscoelastic fluid, in which the physics of the interaction leads either to the overcome the parabolic diffusion model or to consider the parametrization of the concentration with respect to the degrees of freedom associated with the relaxation dynamics of the solvent fluid.

We propose a method for the estimation of the spectral response of a photodetector, using only the variation of the temperature of a black body source without the need of an expensive monochromator or a circular filter. The proposed method is suitable especially for infrared detectors in which the cut – off wavelength and the responsivity vs. wavelength is not exactly known. The method provides a rough estimation of the curve S(l) solving a Fredholm integral equation of the first kind. The precision of this technique depends on the number of temperatures at which the detector output is measured. Some example is given in order to better explain the proposed technique.

Aging involves several changes depending on genetic and behavioural factors, such as lifestyle and number and quality of social relationships, which in turn can be influenced by empathy. Here, the change in the perceived social support across the life span as a function of empathy was investigated, considering the mediating role of the empathy, after controlling for gender and education. 441 people (18-91 years old) filled in the Italian short version of the Interpersonal Support Evaluation List (ISEL-12) and the Social Support Questionnaire (SSQ6) as well as the Empathy Questionnaire (EQ) and the Reading the Mind in the Eyes test (RMET). The mediation analyses with ISEL-12 showed that age and the EQ fully mediated the relationship between age and Appraisal, Belonging and Tangible scores. Further, the EQ fully mediated only the relationship between age and SSQ6-People. These results showed that empathic skills play a key role in the relationships between age and social support. This suggests: empathy can trigger social support and ultimately well-being if stimulated across the lifespan, especially since young age; this would help to form the socio-emotional competence across the years, as a sort of cushion that can be useful in the elderly to fulfil active aging.

This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on Radio Frequency Micro Electro-Mechanical Systems (RF-MEMS), framed within Coplanar Waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 x 1960 µm2 and aiming at attenuation levels of -2, -3 and -5 dB in the 24.25-27.5 GHz range, are presented in their variants featuring both low actuation voltages (5-7 V) as well as higher values (~ 45V), the latter ones ensuring larger mechanical restoring force (and robustness against stiction). Beyond the fabrication non-idealities that affected the described samples, the substantial agreement between simulations and measurement outcomes proved that the proposed designs could provide precise attenuation levels up to 40 GHz, ranging up to nearly -3 dB and -5 dB for the series and shunt variants, respectively. Moreover, they could be effective building blocks for future wideband and reconfigurable RF-MEMS attenuators. In fact, in the second part of this work, combinations of the discussed cells and other configurations meant for larger attenuation levels will be investigated.

Heart failure (HF) is a growing issue in developed countries and most patients present with a reduced ejection fraction. This condition significantly impairs quality of life and represents a threat not only for patients, but also for the entire healthcare system due to its high management cost. In the last decade, new medical treatments and devices have been developed to reduce HF hospitalizations and improve prognosis, while reducing the overall mortality rate. Medical therapy does not achieve the same results in all patients and, whenever it fails, technology comes in handy: novel devices for the management of HF have reduced symptoms. They have also improved the treatment of fluid retention and life threatening arrhythmias. The present review article gives to the readers a comprehensive overview of the most recent and important findings that need to be considered in HF with reduced ejection fraction patients. Both novel medical treatments and devices have been presented and discussed.

Exsolved perovskites can be obtained from lanthanum ferrites, such as La0.6Sr0.4Fe0.8Co0.2O3, as result of Ni doping and thermal treatments. Ni can be simply added to the perovskite by an incipient wetness method. Thermal treatments include calcination in air (e.g., 500 °C) and subsequent reduction in diluted H2 at 800 °C to favor the exsolution process. The chemistry of the nanoparticles exsoluted on the substrate surface can be further modulated by a post treatment in air. These processes allow to produce a two-phase material consisting of a Ruddlesden-Popper type structure and a solid oxide solution e.g. α-Fe100-y-zCoyNizOx oxide. The formed electro-catalyst shows sufficient electronic conductivity under reducing environment at the SOFC anode. Outstanding catalytic properties are observed for the direct oxidation of dry fuels in SOFCs, including H2, methane, syngas, methanol, glycerol and propane. This anode electrocatalyst can be combined with full density electrolyte based on Gadolinia-doped Ceria or with La0.8Sr0.2Ga0.8Mg0.2O3 (LSGM) or BaCe0.9Y0.1O3-δ (BYCO) to form a complete perovskite structure-based cell. Moreover, the exsolved perovskite can be used as a coating layer or catalytic pre-layer of a conventional Ni-YSZ anode. Beside the excellent catalytic activity, this material also shows proper durability and tolerance to sulphur poisoning. In this mini review, preparation methods, physico-chemical characteristics, surface properties of exsoluted and core-shell nanoparticles encapsulated on the metal-depleted perovskite substrate surface, electrochemical properties for the direct oxidation of dry fuels and related electrooxidation mechanisms are examined and discussed.

The co-electrolysis of CO2 and H2O at intermediate temperature is a viable approach for the power-to-gas conversion that deserves for further investigation, considering the need for green energy storage. The commercial solid oxide electrolyser is a promising device, but it is still facing to solve issues concerning the high operating temperatures and the improvement of gas value. In this paper we reported the recent findings of a simple approach that we have amply suggested for solid oxide cells consisting in the addition of a functional layer coated to the fuel electrode of commercial electrochemical cells. This approach simplifies the transition to the next generation of cells manufactured with the most promising materials currently developed and improves the gas value in the outlet stream of cell. Here, the material in use as a coating layer consisted of a Ni-modified La0.6Sr0.4Fe0.8Co0.2O3 which was developed and demonstrated as promising fuel electrode for solid oxide fuel cells. The results discussed in this paper proved the positive role of Ni-modified perovskite as a coating layer for the cathode, since an improvement of about twice was obtained about the quality of gas produced.

The search of DNA polymorphisms useful for the genetic improvement of dairy farm animals lasts more than 40 years with relevant findings in cattle for milk traits, where the best combination of alleles for dairy processing have been found in casein genes and in the DGAT1. Nowadays, similar results are not reached yet in river buffaloes despite advanced genomic technologies and accurate phenotype records are available. The aim of the present study was to investigate and validate in a larger buffalo population the effect on six milk traits of four single nucleotide polymorphisms (SNP) in the CSN1S1, CSN3, SCD and LPL genes, previously reported to be associated with or affect dairy traits in smaller populations often belonging to one farm. A total of 800 buffaloes were genotyped. Daily milk yield (dMY, kg), protein yield (dPY, kg) and fat yields (dFY, kg), fat and protein contents (dFP, % and dPP, %), somatic cell count (SCC, 103cell/ml) and urea (mg/dl) were individually recorded in each month for the whole lactation from 2010 to 2021. A total of 15,742 individual milk test day records (2,496 lactations) were available on 680 buffalo cows with 3.6±1.7 parity (from 1 to 13) and 6.1±1.2 test day records per lactation on average. Three out four SNP in CSN1S1, CSN3 and LPL were associated with at least one of analyzed traits. In particular, the CSN1S1 (AJ005430:c.578C>T) gave favorable associations with all yield traits (dMY, p=0.022; dPY, p=0.014 ; dFY, p=0.029) and SCS (p=0.032), whereas the CSN3 (HQ677596: c.536C>T) positively associated with SCS (p=0.005) and milk urea (p=0.04). Favorable effect on dMY (p=0.028), dFP (p=0.027) and dPP (p=0.050) were observed for the LPL. Conversely, SCD did not show any association with milk traits. This is the first example of confirmation study carried out in the Mediterranean river buffalo for genes of economic interest in dairy field and it represents a very important indication for the preselection of young bulls destined to breeding programs in the view of a more sustainable dairy production.

Heart failure (HF) management in type 1 diabetes (T1D) is particularly challenging due to its increased prevalence and the associated risks of hospitalization and mortality, driven by diabetic cardiomyopathy. Sodium-glucose cotransporter-2 inhibitors (SGLT2-i) offer a promising avenue for treating HF, specifically the preserved ejection fraction variant most common in T1D, but their utility is hampered by the risk of euglycemic diabetic ketoacidosis (DKA). This review investigates the potential of SGLT2-i in T1D HF management, alongside the emergent Continuous Ketone Monitoring (CKM) technology as a means to mitigate DKA risk, through a comprehensive analysis of clinical trials, observational studies, and reviews. The evidence suggests SGLT2-i significantly reduce HF hospitalization and enhance cardiovascular outcomes. However, their application in T1D patients remains limited due to DKA concerns. CKM technology emerges as a crucial tool in this context, offering real-time monitoring of ketone levels, which enables the safe incorporation of SGLT2-i into treatment regimes by allowing for early detection and intervention in the development of ketosis. The synergy between SGLT2-i and CKM has the potential to revolutionize HF treatment in T1D, promising improved patient safety, quality of life, and reduced HF-related morbidity and mortality. Future research should aim at clinical trials directly assessing this integrated approach, potentially guiding new management protocols for HF in T1D.

Electrical transmission between neurons is largely mediated by gap junctions. These junctions allow the direct flow of electric current between neurons, and in mammals are mostly composed of the protein connexin (Cx)36. Circuits of electrically coupled neurons are widespread in these animals, plus, experimental and theoretical evidence supports the notion that, beyond synchronicity, these circuits are able to perform sophisticated operations like lateral excitation and inhibition, noise reduction, as well as the ability to selectively respond upon coincident excitatory inputs. Although once considered stereotyped and unmodifiable, we now know that electrical synapses are subject to modulation and, by reconfiguring neural circuits, these modulations can alter relevant operations. The strength of electrical synapses depends on gap junction conductance, as well as on its functional interaction with the electrophysiological properties of coupled neurons. In particular, voltage dependent channels of the non-synaptic membrane critically determine the efficacy of transmission at these contacts. Consistently, modulatory actions on these channels have been shown to represent relevant mechanisms of plasticity of electrical synaptic transmission. Here we review recent evidence on the regulation of electrical synapses of mammals, the underlying molecular mechanisms, and the possible ways in which they affect circuit function.

This research describes numerical methods to analyze the absolute transport demand of cyclists and then to quantify the road network weaknesses of a city with the aim to identify infrastructure improvements in favor of cyclists. The methods are based on a combination of bicycle counts and map-matched GPS traces and are demonstrated with the city of Bologna, Italy: the dataset is based on approximately 27,500 GPS traces from cyclists, recorded over a period of one month on a volunteer basis using a smartphone application. A first method estimates absolute, city-wide bicycle flows, by scaling map-matched bicycle flows of the entire network to manual and instrumental bicycle counts of the main bikeways of the city. As there is a good correlation between the two sources of flow data, the absolute bike-flows on the entire network have been correctly estimated. A second method describes a novel link-deviation index, which quantifies for each network edge the total deviation generated for cyclists in terms of extra distances traveled with respect to the shortest possible route. The deviations are accepted by cyclists either to avoid unpleasant road attributes along the shortest route or to experience more favorable road attributes along the chosen route. The link deviation index indicates the planner which road links are contributing most to the total deviation of all cyclists – in this way, repelling and attracting road attributes for cyclists can be identified. This is why the deviation index is of practical help to prioritize bike infrastructure construction on individual road network links.

Acceleration rates of vehicles are crucially important statistics needed in two main aspects: first, they are essential to incident reconstructor professionals as having a verified database on where basing the cinematic reconstructions is definitely difficult and moreover, they are useful in order to understand how to create the safest possible environment on the road. This key topic gives es-sential information for road design like intersection schemes, acceleration and deceleration lane length as well as traffic simulation modelling and furthermore, to educate vehicle drivers when entering the traffic flow and to provide limit acceleration values needed to develop autonomous vehicle’s software in order to guarantee a comfort drive. Literature reports tons of linear acceleration stats mainly referred to vehicle performances claimed by car manufacturers, but these data don’t recreate real drivers’ behaviour when entering the road by turning left or right or crossing an intersection. This work aims to integrate the most reliable data from literature with a hybrid and an electric vehicles statistic, adding also two contemporary thermal engine vehicles, extracted conducting probes that recreates real road environment. The entirety of these experiments reconstructs the scenario in which a car is entering the traffic of a two-lanes road, from a stationary position at a stop sign and the acceleration rates are collected using a M.E.M.S. (Microelectromechanical system). Finally, the space needed between the car that is about to enter or crossing the road and the car that is approaching the intersection is calculated, basing the computations on the acceleration values extracted from the probes. These spaces are pictured, as a way to give a concrete idea to readers.

Small and micro hydropower represents an attractive solution for electricity generation, with low cost and low environmental impact. The pump-as-turbine (PAT) approach has promise in this application owing to its low purchase and maintenance costs. In this paper, a new method to predict the inverse characteristic of industrial centrifugal pumps is presented. This method is based on results of simulations performed with commercial three-dimensional CFD software. Model results have been first validated in pumping mode using data supplied by pump manufacturers. Then, results have been compared to experimental data for a pump running in reverse condition. Experimentation has been performed on a dedicated test bench installed in the Department of Civil Construction and Environmental Engineering of the University of Naples Federico II. Three different pumps, with different specific speeds, have been analyzed. Using the model results, the inverse characteristic and the best efficiency point have been evaluated. Finally, results of this methodology have been compared to prediction methods available in the literature.

Polar stratospheric clouds (PSCs) form in polar regions typically between 15 and 25 km, when the local temperature is sufficiently low. PSCs play an important role in the ozone chemistry and the dehydration and denitrification of the stratosphere. Lidars with a depolarization channel may be used to detect and classify different classes of PSCs. The main PSC classes are water ice, nitric acid trihydrate (NAT) and supercooled ternary solutions (STS), the latter being liquid droplets consisting of water, nitric acid and sulphuric acid. PSCs have been observed at the lidar observatory at Concordia Station from 2014 on. The harsh environmental conditions at Concordia during winter render successful lidar operation difficult. In order to facilitate the operation of the observatory several measures have been put in place to achieve an almost complete remote control of the system. PSC occurrence is strongly correlated with local temperatures and is affected by dynamics, as the PSC coverage during the observation season shows.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

Spatial attentional biases can be observed during the processing of linguistic material. For example, we previously reported that healthy subjects overestimate the semantic distance between word stimuli in the right vs left space. Here we explored whether attentional biases are also observed in tasks requiring evaluation of phonological distance between words in the right and left hemispace. Forty-one healthy subjects were presented with triplets of words arranged in space and were asked to indicate the side of space in which the phonological distance between the middle word and an outer word was smaller. In Experiment 1 real words and pseudowords were used, while in Experiment 2 only pseudowords and consonant strings were used. Subjects overestimated the phonological distance between the middle and outer words in the right space. These findings were specific to word stimuli. These results are consistent with the idea that semantic and phonological information may be internally mapped onto spatial representations.

Total Hip Arthroplasty is one of the most successful surgery. However, due to the worldwide growing population life expectancy and the related incidence of age-dependent bone diseases, a growing number of cases of intra-operative fractures lead to revision surgery with high rates of morbidity and mortality. Surgeons choose the type of the implant, either cemented or cementless prosthesis, on the basis of the age, the quality of the bone and the general medical conditions of the patients. Generally, no quantitative measures are available to assess the intra-operative fracture risk. Consequently, the decision-making process is mainly based on medical operators’ expertise and qualitative information obtained by imaging. Motivated by this scenario, we here propose a mechanical-supported strategy to assist surgeons in their decisions, by giving intelligible maps of the risk fracture which take into account the interplay between actual strength distribution inside the bone tissue and its response to the forces exerted by the implant. To this end, we produce charts and patient-specific synthetic “traffic-light” indicators of fracture risk, by making use of ad hoc analytical solutions to predict the stress levels in the bone by means of CT-based mechanical and geometrical parameters of the patient. We felt that, if implemented in a friendly software or proposed as an app, the strategy could constitute a practical tool to help the medical decision-making process, in particular with respect to the choice of adopting cemented or cementless implant

In silico analysis is a promising approach for understanding biological events in complex diseases. Herein, we report an in silico analysis of the entire genome of virus ZikaSPH2015 strain, which was performed in order to identify the occurrence of specific motifs on genomic sequence of Zika Virus that is able to bind and therefore, sequester host’s Transcription Factors (TFs) as well as subsequently predict a possible interactions within host genome. Accordingly to obtained results of this original computational work-flow it is possible to hypothesize that these TFs Binding Motifs might be able to explain the complex and heterogeneous phenotype presentation in Zika Virus affected fe-tus/newborns, as well as the less severe condition in adults. Moreover, the proposed in silico protocol identified thirty three different TFs same as the distribution of TFBSs (Transcription Factor Binding Sites) on ZikaSPH2015 strain, potentially able to influence genes and pathways with biological functions confirming that this approach could find potential answers on disease pathogenesis.

Background: Delayed graft function (DGF) is common after kidney transplantation from de-ceased donor and may significantly affect post-transplant outcomes. This study aimed to evaluating whether an innovative approach, based on the administration of intravenous prostaglandin-analogue iloprost, could be beneficial in reducing the incidence of DGF occurring after kidney transplantation from deceased donors. Methods: This prospective, randomised (1:1), place-bo-controlled study enrolled all consecutive patients who received a kidney transplantation from a deceased donor from January 2000 to December 2012 and who were treated in the peri-transplant period with the prostaglandin-analogue iloprost at 0.27 μg/min through elastomeric pump (treatment group) or placebo (control group). Results: A total of 476 patients were included : DGF was reported in 172 (36.1%) patients in the entire cohort. The multivariate analysis showed that donor’s age > 70 years (OR 2.50, 95% Confidence Interval (CI) 1.40-3.05, p < .001), cold ischemia time > 24 h (OR 2.60, 95 CI 1.50-4.51, p < .001), donor’s AKI (OR 2.71, 95% CI 1.61-4.52, p = .021) and, above all, recipient’s arterial hypotension (OR 5.06, 95% CI 2.52-10.1, p < .0001) were the strongest risk factors for developing post-transplant DGF. The incidence of DGF was 21.4% in the treatment group and 50.9% in the control group (p< .001). Interestingly, among patients who developed DGF, those who received iloprost had a shorter duration of post-transplant DGF (10.58.3 v s13.46.7, days, p= .016). Conclusions: This study showed that the use of a continuous infusion of iloprost could safely and effectively reduce the incidence of DGF in recipients of deceased donor kidneys, allowing a better graft functionality as well as a better graft survival.

Three-phase motors are commonly adopted in several industrial contexts and their failures can result in costly downtime causing undesired service outages; this way, motor diagnostics is an issue that assumes great importance. To prevent their failures and timely face the considered service outages, a non-invasive method to identify electrical and mechanical faults in three-phase asynchronous electric motors is proposed in the paper. In particular, a measurement strategy along with a machine learning algorithm based on Artificial Neural Network is exploited to properly classify failures. In particular, digitized current samples of each motor phase are first processed by means of FFT and PSD in order to estimate the associated spectrum. Suitable features (in terms of frequency and amplitude of the spectral components) are then singled out to either train or feed a neural network acting as a classifier. The method is preliminary validated on a set of 28 electric motors, and its performance is compared with common state-of-art machine learning techniques. The obtained results show that the proposed methodology is able to reach accuracy levels greater than 98\% in identifying anomalous conditions of three-phase asynchronous motors.

Background: Glioma surgery was remarkably renewed in the past 2 decades, with improved safety and limited but yet improved life expectations. Fluorescence-guided resection of high-grade gliomas (HGG) plays a central role in this sense, by allowing higher degrees of extent of resection (EOR). The introduction of the exoscopic guided surgery may be considered an im-plementation for fluorescence techniques over the traditional microscopes. We present the appli-cation and the advantages of the exoscopic guided surgery compared to the microscopic surgery in tumor resection guided by 5-ALA fluorescence in patients with HGG. Methods: ten consecutive patients underwent a surgery for HGG resection. The surgery was per-formed via an exoscopic-guided procedure (Olympus Orbeye) and after oral administration of Gliolan 5 hours before the procedure. During surgery, the procedure was shifted to microscope (Kinevo 900, Zeiss) view. The intensity of the fluorescence under the two different was subjectively measured in different picture samples during the surgery in a 1 to 5 (from minimum to maxi-mum) scale. The brightness of the surgical field and the detailing of the anatomy were also ana-lyzed comparatively. Results: among the ten patients the histopathological diagnosis was an high grade glioma in all cases. In 9 cases was possible to achieve the gross total resection. There was no perioperative mortality. The median fluorescence intensity, on a scale of 1–5, was 4.5 in the exoscope group and 3.5 in the microscope group (p

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

Lower urinary tract symptoms (LUTS) and hematuria are common symptoms in men with benign prostatic hyperplasia (BPH) and prostate cancer (PCa) mainly affecting the elderly population. Prostatic arterial embolization (PAE) is a minimally invasive pro-cedure that has shown promising results in managing massive intractable prostatic he-maturia in patients with BPH and PCa. A few studies, however, have provided valuable insights into the durability and efficacy of PAE focusing on the long-term effectiveness, quality of life, and cancer-specific control of hemostasis and urinary symptoms. As a result of concomitant cardiovascular conditions, these patients often take anticoagulants or antithrombotics, which can worsen their hematuria and clinical status. Transurethral resection of the prostate (TURP) is considered a very high-risk procedure even without massive bleeding, and requires discontinuation of Vitamin K antagonists and antiplate-let therapies. Such patients usually have their surgery postponed, and PAE should be considered a safe alternative treatment. We aimed to report a narrative review from 1976 to June 2023 of the current state of PAE for massive and intractable hematuria highlighting recent developments in this technique, including prospective cohort stud-ies and focusing on long-term outcome, safety, and complication management in PCa patients with significant hemorrhagic symptoms. As an additional contribution, we propose a simple algorithm for treating intractable bleeding associated with prostate cancer in a 92-year-old man with LUTS.

The paper investigates the performance of a full analog self-jammer canceller able to operate in UHF RFID devices. The scheme has been realized using only SMT devices avoiding custom designed components. The paper analyzes the theoretical performance and experimental validation using a modular microwave technology approach.

Sensitivity to weather conditions, and specially to clouds, is a severe limiting factor to the use of optical remote sensing for Earth monitoring applications. A possible alternative, is to resort to weather-insensitive synthetic aperture radar (SAR) images. However, in many real-world applications, critical decisions are made based on some informative spectral features, such as water, vegetation or soil indices, which cannot be extracted from SAR images. In the absence of optical sources, these data must be estimated. The current practice is to perform linear interpolation between data available at temporally close time instants. In this work, we propose to estimate missing spectral features through data fusion and deep-learning. Several sources of information are taken into account - optical sequences, SAR sequences, DEM - so as to exploit both temporal and cross-sensor dependencies. Based on these data, and a tiny cloud-free fraction of the target image, a compact convolutional neural network (CNN) is trained to perform the desired estimation. To validate the proposed approach, we focus on the estimation of the normalized difference vegetation index (NDVI), using coupled Sentinel-1 and Sentinel-2 time-series acquired over an agricultural region of Burkina Faso from May to November 2016. Several fusion schemes are considered, causal and non-causal, single-sensor or joint-sensor, corresponding to different operating conditions. Experimental results are very promising, showing a significant gain over baselines methods according to all performance indicators.

The paper investigates the theory of operation of a passive millimeter-wave seeker sensor using fast electronic sequential-lobing technique and the experimental validation obtained through laboratory trials. The paper analyzes in detail the theoretical performance of a difference channel sensor and a pseudo-monopulse sensor deriving agile formulas for the estimation of target angular tracking accuracy and the subsequent experimental validation.

Radiation Fireballs are singular phenomena which involve severe thermal radiation and consequently, they need to be duly assessed and prevented. Although the radiative heat transfer produced by a sphere is relatively well known, the shadowing measures implemented to control the fireball’s devastating effects have frequently posed a difficult analytical instance, mainly due to its specific configuration. In this article, since the usual solving equations for the said cases are impractical, the authors propose a novel graphic-algorithm method that sorts the problem efficiently for different kinds of obstructions and relative positions of the fireball and the defenses. Adequate application of this method may improve the safety of a significant number of facilities exposed to such risks.

In this paper, different concepts of reconfigurable RF-MEMS attenuators for beamforming applications are proposed and critically assessed. Capitalizing on the previous part of this work, the 1-bit attenuation modules featuring series and shunt resistors and low-voltage membranes (7-9 V) are employed to develop a 3-bit attenuator for fine-tuning attenuations (&lt; -10 dB) in the 24.25-27.5 GHz range. More substantial attenuation levels are investigated by means of fabricated samples of coplanar waveguide (CPW) sections equipped with Pi-shaped resistors aiming at attenuations of -15, -30, and -45 dB. The remarkable electrical features of such configurations, showing flat attenuation curves and limited return losses, and the investigation of a switched-line attenuator design based on them led to the final proposed concept of a low-voltage 24-state attenuator. Such simulated device combines the Pi-shaped resistors for substantial attenuations with the 3-bit design for fine-tuning operations, showing a maximum attenuation level of nearly -50 dB while maintaining steadily flat attenuation levels and limited return losses (< -11 dB) along the frequency band of interest.

Time irreversibility, i.e. the lack of invariance of the statistical properties of a system under time reversal, is a fundamental property of all systems operating out of equilibrium. Time reversal symmetry is associated with important statistical and physical properties and is related to the predictability of the system generating the time series. Over the past fifteen years, various methods to quantify time irreversibility in time series have been proposed, but these can be computationally expensive. Here we propose a new method, based on permutation entropy, which is essentially parameter-free, temporally local, yields straightforward statistical tests, and has fast convergence properties. We apply this method to the study of financial time series, showing that stocks and indices present a rich irreversibility dynamics. We illustrate the comparative methodological advantages of our method with respect to a recently proposed method based on visibility graphs, and discuss the implications of our results for financial data analysis and interpretation.

In the last decades synthetic jet actuators have gained much interest among the flow control techniques due to their short response time, high jet velocity and absence of traditional piping, that matches the requirements of reduced size and low weight. A synthetic jet is generated by the diaphragm oscillation (generally driven by a piezoelectric element) in a relatively small cavity, producing periodic cavity pressure variations associated with cavity volume changes. The pressured air exhausts through an orifice, converting diaphragm electrodynamic energy into jet kinetic energy. This review paper faces the development of various lumped-element models (LEMs) as practical tools to design and manufacture the actuators. LEMs can quickly predict device performances such as the frequency response in terms of diaphragm displacement, cavity pressure and jet velocity, as well as the efficiency of energy conversion of input Joule power into useful kinetic power of air jet. The actuator performance is analyzed also by varying typical geometric parameters such as cavity height and orifice diameter and length, through a suited dimensionless form of the governing equations. A comprehensive and detailed physical modeling aimed to evaluate the device efficiency is introduced, shedding light on the different stages involved in the process. Overall, the influence of the coupling degree of the two oscillators, the diaphragm and the Helmholtz’s one, on the device performance is discussed throughout the paper.

The present study aims to evaluate the ability of peonidin and petunidin-3-glucoside (Peo and Pet-3-glc) and their metabolites (vanillic acid; VA and methyl-gallic acid; MetGA), to prevent monocyte (THP-1) adhesion to endothelial cells (HUVECs), and to reduce the production of VCAM-1, E-selectin and VEGF in a stimulated pro-inflammatory environment, a pivotal step of atherogenesis. Tumor necrosis factor-α (TNF-α; 100 ng mL-1) was used to stimulate the adhesion of labelled monocytes (THP-1) to endothelial cells (HUVECs). Successively, different concentrations of Peo-3-glc and Pet-3-glc (0.02, 0.2, 2 and 20 µM) and VA and MetGA (0.05, 0.5, 5 and 50 µM) were tested. After 24 h, the production of VCAM-1, E-selectin and VEGF was quantified by ELISA kits, while the adhesion process was measured spectrophotometrically. Peo-3-glc and Pet-3-glc (from 0.02 to 20 µM) significantly (p<0.0001) decreased THP-1 adhesion to HUVECs at all concentrations (-37%, -24%, -30% and -47% for Peo-3-glc; -37%, -33%, -33% and -45% for Pet-3-glc). VA, but not MetGA, reduced the adhesion process at 50 µM (-21%; p<0.001). At the same concentrations, a significant (p<0.0001) reduction of E-selectin, but not VCAM-1, was documented. In addition, anthocyanins and their metabolites significantly decreased (p<0.001) VEGF production. The present findings suggest, that while Peo-3-glc and Pet-3-glc, but not their metabolites, reduced monocyte adhesion to endothelial cells through suppression of E-selectin production, VEGF production was reduced by both anthocyanins and their metabolites suggesting a role in regulation of angiogenesis.

Energy management systems (EMS) play a central role in improving the performance of microgrids by ensuring their efficient operation while minimizing operational costs and environmental impacts. This paper presents a comprehensive study of a MILP-based EMS developed and implemented in MATLAB using Yalmip software for the energy management of a new positive energy district in the city of Savona, Italy, as part of the Interreg Alpine Space Project ALPGRIDS. The main objective of this research is to optimize the functioning of the microgrid, focusing on cost efficiency and environmental sustainability. In pursuit of this objective, the EMS undergoes comprehensive testing and analysis, replicating actual conditions and addressing the diverse demands of end-users across typical days throughout the year considering real electricity selling and purchase price. The EMS also accounts for the reactive power capabilities of the various technologies integrated into the microgrid. The levelized cost of electricity (LCOE) serves as a metric for assessing curtailment costs, while penalties related to reactive power absorption from the distribution network are appraised in alignment with prevailing regulatory guidelines. The case study provides valuable insights into the practical implementation of EMS technology in microgrids and demonstrates its potential for sustainable energy management in complex urban energy districts. The insights and strategies developed through this research contribute to the overall goals of improving energy efficiency and reducing the environmental footprint of future energy districts.

The connectivity level of last-generation vehicles is constantly on the rise. The combined use of Vehicle-To-Everything (V2X) connectivity and autonomous driving can provide remarkable benefits through the optimization of the route and speed trajectory. In this framework, this paper focuses on vehicle eco-driving optimization in a connected environment. The virtual test rig of a premium segment passenger car was used for generating the simulation scenarios. The benefits, in terms of energy and time savings, that the introduction of V2X communication, integrated with cloud computing, can have in a real-world scenario were assessed. The Reference Scenario is a pre-defined Real Driving Emissions (RDE) compliant route, while the simulation scenarios were generated by assuming two different penetration levels of V2X technologies. The associated energy minimization problem is formulated and solved by means of a global optimization algorithm, i.e., Dynamic Programming (DP). The optimization framework includes information coming from the surrounding environment, e.g., traffic lights state, speed limits, distance to travel, etc. The simulations show that introducing a smart infrastructure along with optimizing the vehicle speed in a real-world route can potentially reduce the required energy by 54% while shortening the travel time by 38%. Finally, a sensitivity analysis is performed on the bi-objective optimization cost function to find a set of Pareto optimal solutions, between energy and travel time minimization.

Several criteria exist to diagnose pulmonary aspergillosis with varying degrees of certainty in specific populations, including oncohaematological patients (EORTC/MSG), ICU patients (AspICU) and Covid-19 patients (ECMM). At the beginning of the pandemic, however, the diagnosis of Covid-19 Associated Pulmonary Aspergillosis (CAPA) could not be performed easily, and the decision to treat (DTT) was empirical. In this cross-sectional retrospective study including patients with SARS-CoV-2 infection and a suspicion of CAPA, we studied the concordance between the DTT and the three diagnostic criteria using Cohen’s coefficient, then we identified the factors associated with the DTT and we corrected by treatment to study the influence of the diagnostic criteria on survival. We showed good concordance of DTT and AspICU and ECMM criteria, with “compatible signs”, “positive culture” and “positive galattomannan” influencing the DTT. Treatment also showed a positive effect on survival once corrected for a putative, possible or probable diagnosis of CAPA using AspICU and ECMM criteria. We conclude that EORTC/MSGERC are not considered applicable in clinical practice due to lack of inclusion of signs and symptoms and do not lead to improved survival. AspICU and ECMM criteria showed a good degree of agreement with the DTT and a positive correlation with patient recovery.

Colombia has one of the largest numbers of internally displaced populations in the world and recently entered a period of post-conflict. These socio-political processes and trends have increased the migration of people towards cities and accordingly are affecting the distribution and occurrence of tropical diseases in its urban and peri-urban areas. Studies have suggested that many human phenomena such as urbanization scale according to the size of human populations regardless of cultural context. But other studies show that health epidemics such as malarial and human immunodeficiency virus infections, follow a scale-free distribution in terms of population size and density. We explore these relationships and dynamics in a tropical context using statistical analyses and available geospatial data to identify the scale dynamics between urbanization processes and disease transmission in Colombia. We found that rural populations and certain disease dynamics were described by power-laws that are frequently mentioned in urbanization studies. However, we found that malaria presented higher intensity of infection in human settlements of less than 50,000 individuals, particularly for ethnic indigenous populations. Results indicate that epidemics and urbanization dynamics do indeed follow scales in Colombia; findings that differ from previous epidemiological studies such as those for malarial infection. Additionally, we identified trends showing that malarial infections become endemic in peri-urban areas. Targeting such peri-urban locations and certain demographic groups are key for managing public health issues in the urbanizing tropics.

Despite available global efforts and funding, Tuberculosis (TB) continues to affect a considerable number of patients worldwide. Policy makers and stakeholders set clear goals to reduce TB incidence and mortality, but the emergence of multidrug-resistant TB (MDR-TB) and extensively drug-resistant TB (XDR-TB) complicate the reach of these goals. Drug-resistance TB needs to be diagnosed rapidly and accurately to effectively treat patients, prevent the transmission of MDR-TB, minimise mortality, reduce treatment costs and avoid unnecessary hospitalisations. In this narrative review, we provide a comprehensive overview of laboratory methods for detecting drug resistance in MTB, focusing on phenotypic, molecular and other drug susceptibility testing (DST) techniques. We found a large variety of methods used, with the BACTEC MGIT 960 being the most common phenotypic DST and the Xpert MTB/RIF being the most common molecular DST. We emphasise the importance of integrating phenotypic and molecular DST to address issues like resistance to new drugs, heteroresistance, mixed infections and low-level resistance mutations. Notably, most of the analysed studies adhered to the outdated definition of XDR-TB and did not consider the pre-XDR definition, thus posing challenges in aligning diagnostic methods with the current landscape of TB resistance.

Today's unstable labor market increasingly requires flexibility and adaptability to cope with the threat of unemployment. It can cause distress in people and have a more significant negative impact on fragile workers, such as migrants. This study aimed to test whether a Career Counseling intervention designed for Migrants (CCfM) can develop Career Adaptability and, therefore, both Work Self-efficacy (WSe) and Job Search Self-efficacy (JSSe) perceptions. It was conducted in Italy and involved a sample of 233 migrants, who were asked to respond to a questionnaire available in three languages (Italian, French, and English). Data analysis showed that an improvement was demonstrated in all the variables considered, namely career adaptability (including concern, control, confidence, and curiosity), WSe, and JSSe, even though the CCfM was not directly designed to increase the last one. In addition, the development of career adaptability explained the increase in migrants' WSe and JSSe, and the initial level of career adaptability was found to explain the increase in WSe due to the initial positive level of curiosity.

Abstract: For decades, researchers have suggested the existence of a bilingual cognitive advantage, especially in tasks involving executive functions such as inhibition, shifting, and updating. Recently, an increasing number of studies have questioned whether bilingualism results in change in executive functions, highlighting conflicting data published in the literature. The present study compared the performance of third-, fourth-, and fifth-grade bilingual and monolingual children on attentional and cognitive tasks. Participants were 61 monolingual and 74 bilingual children (M = 114.6 months; SD = 8.48 months) who were tested on two versions of the Attention Network Task (ANT), with and without social stimuli, as well as tests investigating working memory, short-term memory, narrative memory, and receptive vocabulary. Data on families’ socioeconomic status and children’s reasoning abilities were also collected. The results showed that bilingualism and socioeconomic status affected attentional networks in tasks involving social stimuli. In tasks involving non-social stimuli, socioeconomic status only affected the alerting and executive conflict networks. Consistent with the literature, a positive relationship emerged between socioeconomic status and executive control in the context of social stimuli, and a negative relationship emerged between socioeconomic status and the alerting network in the context of non-social stimuli. Interestingly, neither socioeconomic status nor social attentional networks correlated with working memory. Therefore, although more investigations are required, the results suggest that differences in social contexts mainly affect attentional functions.

In the recent decades, per- and polyfluoroalkyl substances (PFAS) have garnered widespread public attention due to their persistence in the environment and detrimental effects on the health of living organisms, spurring the generation of several transcriptome-centered investigations to understand the biological basis of their mechanism. In this study, we collected 2144 publicly available samples from 7 distinct animal species to examine the molecular responses to PFAS exposure and to determine if there are conserved responses. Our comparative transcriptional analysis revealed that exposure to PFAS is conserved across different tissues, molecules and species. We identified and reported several genes exhibiting consistent and evolutionarily conserved transcriptional response to PFAS, such as ESR1, HADHA and ID1, as well as several pathways including lipid metabolism, immune response and hormone pathways. This study provides the first evidence that distinct PFAS molecules induce comparable transcriptional changes and affect the same metabolic processes across inter-species borders. Our findings have significant implications for understanding the impact of PFAS exposure on living organisms and the environment. We believe that this study offers a novel perspective on the molecular responses to PFAS exposure and provides a foundation for future research into developing strategies for mitigating the detrimental effects of these substances in the ecosystem.

: Innovative solutions are now being researched to manage the ever-increasing amount of data required to optimize the performance of internal combustion engines. Machine Learning ap-proaches have shown to be a valuable tool for signal prediction due to their real-time and cost-effective deployment. Among them, the architecture consisting of Long Short-Term Memory (LSTM) and one-dimensional Convolutional Neural Networks (1DCNN) has emerged as a highly promising and effective option for replacing the role of physical sensors. The architecture com-bines the capacity of LSTM to detect patterns and relationships in smaller segments of the signal with the ability of 1DCNN to detect patterns and relationships in larger segments of the signal. The purpose of this work is to assess the feasibility of substituting a physical device dedicated to calculating the torque supplied by a spark-ignition engine. The suggested architecture was trained and tested using signals from the field during a test campaign conducted under transient operating conditions. The results reveal that LSTM+1DCNN is particularly well suited for signal prediction with considerable variability. It constantly outperforms other architectures used for comparison, with average error percentages of less than 2%, proving the architecture's ability to replace physical sensors.

The effect of the communication channel size on the transport and subsequent detection of chemical messengers is investigated on millimetric and micrometric channels. The transport of the information carriers, being characterized by an advective and a diffusive contribution, was simulated by varying the flow velocity and the diffusion coefficient. Then, to evaluate the information quality, the Intersymbol Interference (ISI) between two consecutive signals at a specific release delay was estimated. This allowed us to verify that operating under micrometric channel conditions has a larger flow velocity range to obtain completely separated successive signals and smaller release delays can be used between signals. The theoretical results were confirmed by developing a prototype molecular communication platform operating under microfluidic conditions, which enables communication through fluorescent nanoparticles, namely Carbon Quantum Dots (CQDs).

To contribute to small and medium enterprises (SMEs) sustainable transition into the circular economy, the study proposes the activation of organizational learning (OL) processes – denoted here as multi-level knowledge creation, transfer, and retention processes – as a key phase in introducing circular business models (CBMs) at SME and supply chain (SC) level. The research employs a mixed-method approach, using the focus group methodology to identify contextual elements impacting on CBM-related OL processes, and a survey-based evaluation to single out the most frequently used OL processes inside Italian construction SMEs. As main result, a CBM-oriented OL multi-level model offers a fine-grained understanding of contextual elements acting mutually as barriers and drivers for OL processes, as possible OL dynamics among them. The multi-level culture construct – composed of external stakeholders’, SC stakeholders’, and organizational culture – identify the key element to activate CBM-oriented OL processes. Main implications are related to the identification of cultural, structural, regulatory, and process contextual elements across the external, SC, and organizational levels, and their interrelation with applicable intraorganizational and interorganizational learning processes. The proposed model would contribute to an improved implementation of transitioning into the circular economy utilizing sustainable business models in the construction SMEs.

South Italy is characterised by a semi-arid climate with scarce rain and high evaporative demand, therefore the need to optimise water resources in this area is crucial, and climate change could worsen this condition. In citrus cultivation, which is one of the most important crops bred in Southern Italy, and more generally in Mediterranean regions, deficit irrigation strategies are im-plemented in order to cope with limited resource availability. On this basis, knowledge on how the territorial distribution of citrus would change in relation to these strategies constitutes valuable information for the stakeholders. Therefore, the objective of this study was to determine the prob-ability of presence of citrus in Sicily at changing of the percentage of water deficit application, in order to analyse change in the surface area and localisation of the crop. The methodology was based on the application of Species Distribution Models and Geographic Information Systems to the case study of the Province of Syracuse in Sicily. Different geostatistical and machine learning models were applied, based on 3-decades bioclimatic variables, DTM and irrigation; assessment of the outcomes was carried by using classification evaluation metrics. The analysis of the outcomes showed that uncorrelated predictor layers mainly included water input that affected most the probability of presence. Moreover, GIS analyses showed that deficit irrigation strategies would generate an overall reduction of cultivation surfaces in the territory and a decrease of citrus pres-ence in southern areas of the considered territory, where climate conditions are less favourable in terms of temperature and precipitations, thus providing useful information for decision support tools in agriculture and land use policy.

An Oscillating Water Column device, specifically a Savonius turbine, underwent comprehensive testing within an air duct to evaluate its performance under varying rotational speeds, flow directions, and the presence of power augmenters positioned both in front of and behind the device. The experimental setup involved the utilization of load cells and pressure transducers, with their data utilized to calculate pressure differentials across the turbine and torque. Subsequently, a predictive model based on decision trees was developed using Machine Learning. This model was then used to analyze the influence of various features on predicting the pressure difference, considered as the output. The results of the validation (10-fold cross-validation) and test phases were thoroughly investigated. Moreover, obtaining a predictive model allows for the exploration of different scenarios without relying solely on physical experimentation, thereby broadening the scope for further testing.

The subject of this paper is to analyse the Math Principia of Economic 3D Black Holes in Roegenian economics. This idea is totally new in the related literature, excepting our papers. In details, we study two special problems: (i) math origin of economic 3D black holes, (ii) entropy and internal political stability depending on national income and the total investment, for economic RN 3D black hole. To solve these problems, it was necessary to jump from macroeconomic side to microeconomic side (a substantial approach so different), to complete the thermodynamics-economics dictionary with new entities, to introduce the flow between two macroeconomic systems, to study the Schwarzschild type metric properties on an economic 4D system, together with Rindler coordinates, Einstein 4D PDEs, and economic RN 3D black hole. In addition, we introduce some economic Ricci type flows or waves, for further research.

The public administrations (PAs) that have joined the Covenant of Mayors must now complete their adaptation plans with the climate chapter (SECAP). At the same time, the previous Plan for sustainable energy (SEAP) was mainly dedicated to mitigation actions (sustainable energy). It was often managed directly by municipalities' in-house energy companies or agencies. The WMO1234 Recommendation (Guidance on Integrated Urban Hydrometeorological, Climate and Environmental Services) is a fundamental Guidance to allow PAs to make policies and decisions regarding city regeneration and population health prevention. The purpose of this manuscript is to describe a process undertaken in the Emilia-Romagna region to build a coherent frame from the individuation of local environmental vulnerabilities and adopt specific policies. This frame was created by the contribution of various Institutions, including the Regional Authority, which furnished the main directives and tools for the mitigation and adaptation, the Municipality of Bologna, which prepared the first Adaptation Plan following the SECAP guidance, the Emilia-Romagna branch of Italian Association of Municipalities (ANCI), which took in charge the approach to harmonize different urban contexts and to communicate with stakeholders and population, and Research Institutes and Scientific Associations to explore, with specific studies and modeling application, the outcomes produced by a joint support to the new urban directives, such as the General Urban Planning Plan (PUG). To achieve this result, the WMO Guidance 1234 has been assumed as a reference methodology to ensure the best utilization of available data and widespread a common science-based methodological approach to other municipalities.

The concepts of accessibility and urban walkability are the cornerstones of urban policies for the contemporary city, called upon to adopt sustainable development models in line with the objectives of the 2030 Agenda and the ambitious objectives of the 'European Green Deal'. These concepts are closely linked to the paradigm of a sustainable city (livable, healthy and inclusive), founded on a system of quality public spaces and on a network of services and infrastructures, both tangible and intangible, capable of strengthening or building new relationships: social, economic and environmental. It is therefore necessary to recognize potential opportunities for connection and permeability in consolidated urban environments, very often fragmented and characterized by enclaves. Within this framework, the city of Cagliari represents an interesting case study as it is characterized by the presence of a series of military complexes, real 'enclaves' which condition the proximity connections and, more generally, the walkability. In this sense, building on previous research and analysis of policies and projects aimed at reintroducing, even partially, this military asset into civilian life (Green Barracks Project - GBP - 2019), this study proposes and applies a methodology to improve urban accessibility in a flexible network logic, where 'walkability' can become not only a moment of possible "choice" but the basis for planning oriented to the '15 min city' model or, more generally, to the renewed, inclusive, safe, resilient and sustainable “City of proximity”.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

The spike protein (S) of SARS-CoV-2 has been shown to bind to the human angiotensin-converting enzyme 2 (ACE2) receptor with much higher affinity compared to other coronaviruses. The binding interface between the ACE2 receptor plays a critical role in the entry mechanism of SARS-CoV-2 virus. There are specific amino acids involved in the interaction between S protein and ACE2 receptor. This specificity is critical for the virus to establish a systemic infection and cause COVID-19 disease. In the ACE2 receptor, the largest number of amino acids that play a crucial role in the mechanism of interaction and recognition with the S protein are located in the C-terminal part which represents the main binding region between ACE2 and S. This fragment is abundant in coordination residues such as aspartates, glutamates and histidine that could be targeted by metal ions. Zn²⁺ ion binds to the ACE2 receptor in its catalytic site and modulates its activity, but it could also contribute to the structural stability of the entire protein. The ability of the human ACE2 receptor to coordinate metal ions, such Zn²⁺, in the same region where it binds to the S protein could have a crucial impact in the mechanism of recognition and interaction of ACE2-S with consequences on their binding affinity that deserve to be investigated. To test this possibility, this study aims to characterize the coordination ability of Zn²⁺, and also Cu²⁺ for comparison, with selected peptide models of the ACE2 binding interface using spectroscopic and potentiometric techniques.

Introduction: Due to the great development of digital technology, through CAD (Computer - Aided Design) and CAM (Computer - Aided Manufacturing) systems, digital models could be used in orthodontic treatment planning decision-making, as there are numerous studies in the literature that support the validity of measurements of digital models of anterior teeth and the total coefficient of Bolton analysis. The aim of the study was to compare the average length value of the current upper and lower arches with that of a hypothetical nickel-titanium wire and the accuracy of the Bolton index measurement. In the present study, 138 dental casts were analyzed using Ortho3Shape software. Using the Ortho3Shape software, it was possible to measure the real and ideal lower arch lengths and, with regard to Bolton analysis, the values of the anterior and total Bolton coefficients. By comparing the values obtained with those of the study by A. Anand Kumar et al. using CBCT and plaster casts, the reliability of the measurements obtained with such CAD/CAM orthodontic software was evaluated. Considering the validity of digital measurements demonstrated by the studies and systematic reviews in the literature, it can be stated that CAD/CAM digital models can be a viable alternative to plaster models in the coming years, as they can facilitate model preservation and retrieval. For future studies and research, it would be preferable to use intra-oral scanners (IOS) in order to ensure greater accuracy, requiring only one step and ensuring a better outcome for the patient.

The effects of the climate crisis are affecting ecosystems at different scales and magnitudes. This paper focuses on a massive Mediterranean mussel die-off observed along the middle Italian Adriatic coast in the summer of 2022. We considered the possible environmental causes of this phenomenon and carried out a climatic analysis of the last decade. We performed field surveys in different locations along a 16 Km coastal stretch (from Martinsicuro (TE) on the South, to Grottammare (AP) on the North). The study area includes two marine Sites of Community Importance under the European Natura 2000 network. The mussels die-off has interested practically all the natural mussel-beds colonizing the study area. Mussels are sessile filter-feeding organisms inhabiting the intertidal zone, therefore, are highly exposed to variations in environmental conditions such as temperature and nutrient load. We discuss the possible causes of this die-off, proposing that high temperature and the scarce availability of food acted simultaneously as stress factors, generating local unsustainable living conditions for this species.

Insulin resistance/hyperinsulinemia as an independent risk factor for the development and worsening of HFpEF. Serafino Fazio MD¹, Valentina Mercurio MD, PhD2, Valeria Fazio MD3, Antonio Ruvolo MD⁴, Flora Affuso MD, PhD⁵. Authors’ Affiliation: ¹ Department of Internal Medicine (retired Professor). Federico II University, Via Sergio Pansini 5. 80135 Naples, Italy. 2 Department of Translational Medical Sciences. Federico II University. Via Sergio Pasini 5. 80135 Naples, Italy. ³ UOC Medicina Interna, Azienda Ospedaliera di Caserta, 81100 Caserta, Italy, ⁴ UOC Cardiologia AORN dei colli PO CTO, Viale Colli Aminei 21, 80100 Naples, Italy. ⁵ Independent researcher, Viale Raffaello 74, 80129 Naples, Italy. Abstract Heart failure (HF) has become a subject of continuous interest since it has been declared new pandemic in 1997 because of the exponential increase in hospitalizations for HF in the latest years. HF is the final state to which all heart diseases of different etiologies lead if not adequately treated, therefore it is highly prevalent worldwide, with a progressive increase with age, reaching a prevalence of 10% in subjects over the age of 65 years. It should also be underlined that lately, while the prevalence of HF with left ventricular reduced ejection fraction (HFrEF) is slowly decreasing, the incidence of HF with left ventricular preserved ejection fraction (HFpEF) is progressively increasing. In deed, among patients consecutively hospitalized for HF between 1987 and 2001 in a study from the Mayo Clinic Hospitals in Olmsted County, Minnesota, prevalence of HFpEF increased from 38% to 54%. HFpEF is typically characterized by concentric remodeling of the left ventricle (LV) with impaired diastolic function and increased filling pressures. Over the years, also the prevalence of insulin resistance/hyperinsulinemia in the general adult population has progressively increased, primarily due to lifestyle changes, particularly in developed and developing countries, with a range that globally ranges between 15.5% and 46.5%. Notably, insulin resistance (IR)/hyperinsulinemia (Hyperins) is present in up to 60% of patients with HF and is significantly higher in subjects with HfpEF. In the scientific literature it has been well highlighted that the increased circulating levels of insulin are associated with conditions of insulin resistance are responsible for progressive cardiovascular alterations over the years. In the setting of HFpEF, insulin stimulates the concentric remodeling of the left ventricle with associated diastolic dysfunction, which, coincidentally. Unfortunately, IR/Hyperins, despite being a well-known cardiovascular risk factor, is still not screened in the general population and is not treated as promptly as it should be, and this could at least in part concur in the progressive increase in prevalence of HFpEF in the general adult population. The aim of this manuscript was to review scientific literature that support a pathophysiologic connection between IR/Hyperins and HFpEF to stimulate the scientific community towards the identification of hyperinsulinemia associated with insulin resistance as an independent cardiovascular risk factor in development and worsening of HF, believing that its adequate screening in the general population and appropriate treatment could reduce the prevalence of HFpEF and improve its progression.

The ethics of invertebrate research have largely been ignored compared to the consideration of higher order animals, but more recent focus has questioned this trend. Using biohybrid robotic jellyfish as a case study, we examine the ethical considerations of invertebrate work and provide recommendations for future guidelines. This paper starts with an overview of philosophical views of animal ethics, the current state of knowledge for invertebrate pain and nociception, and current ethical guidelines. Next, we delve into the case study and analogous precedents. Specifically, in prior studies, we developed biohybrid robotic jellyfish, which modified live moon jellyfish with microelectronic swim controllers for future applications in ocean monitoring. Although jellyfish possess no central nervous system, pain receptors, or nociceptors, we closely monitored their stress responses, using the precautionary and minimization principles in consideration of the 4Rs: reduction, replacement, refinement, and reproducibility. We also discuss ethical considerations related to our studies and suggest that public opinion of invertebrate research relies heavily on repugnance, including fears of ‘playing God’ or limiting the ‘free will’ of animals. These issues are also examined for prior bioethics cases, such as the RoboRoach, cyborg beetle, ‘microslavery’ of microbes, biohybrid robots incorporating tissues from sea slugs (which are known to possess nociceptors), and other tissue cutting experiments involving soft-bodied invertebrates. However, biohybrid robotic jellyfish pose further ethical questions of potential ecological consequences as ocean monitoring tools, such as the impact of electronic waste in the ocean. To conclude these evaluations, we recommend that publishers require brief ethical statements for invertebrate research, which can include the following: a scientific justification for the research, discussion of the 4Rs, and cost-benefit analysis. We also delineate the need for more research on pain and nociception in invertebrates, which can then be used to revise or validate current research standards. These actions provide a stronger basis for the ethical study of invertebrate species, with implications for individual, species-wide, and ecological impacts on animals, as well as for interdisciplinary studies in science, engineering, and philosophy.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

We construct admissible circulant Laplacian matrix functions as generators for strictly increasing random walks on the integer line. These Laplacian matrix functions refer to a certain class of Bernstein functions. The approach has connections with biased walks on digraphs. Within this framework, we introduce a space-time generalization of the Poisson process as a strictly increasing walk with discrete Mittag-Leffler jumps subordinated to a (continuous-time) fractional Poisson process. We call this process ‘space-time Mittag-Leffler process’. We derive explicit formulae for the state probabilities which solve a Cauchy problem with a Kolmogorov-Feller (forward) difference-differential equation of general fractional type. We analyze a “well-scaled” diffusion limit and obtain a Cauchy problem with a space-time convolution equation involving Mittag-Leffler densities. We deduce in this limit the ‘state density kernel’ solving this Cauchy problem. It turns out that the diffusion limit exhibits connections to Prabhakar general fractional calculus. We also analyze in this way a generalization of the space-time fractional Mittag-Leffler process. The approach of construction of good Laplacian generator functions has a large potential in applications of space-time generalizations of the Poisson process and in the field of continuous-time random walks on digraphs.

Critically ill patients treated in the intensive care unit (ICU) can present many abdominal conditions that need a prompt diagnosis and timely treatment because of their general frailty. Clinical evaluation and diagnostic tools like ultrasound or CT scan are not reliable or feasible in these patients. Bedside laparoscopy (BSL) is a minimally invasive procedure that allows surgeons to assess the abdominal cavity directly in the ICU, thus avoiding unnecessary exploratory laparotomy or incidence related to intra-hospital transfer. We conducted a review of the literature to summarize the state-of-the-art of BSL. Medline, The Cochrane Central Register of Controlled Trials (CENTRAL), and Scopus databases were utilized to identify all relevant publications. Indications, contraindications, technical aspects, and outcomes are discussed. The procedure is safe, feasible, and effective. When other diagnostic tools fail to diagnose or exclude an intra-abdominal condition in ICU patients, BSL should be preferred over exploratory laparotomy.

Deforestation is an important environmental problem in México and a key promoter of regional climate change through modifying the surface albedo. The objective of this research was to characterize the impact of deforestation and land use changes on surface albedo (α) and climate patterns in the Municipality of Tapalpa, Jalisco, México between the years 2014 and 2021. The main land cover types are coniferous forests (CF), oak and gallery woodlands (OGW), and annual agriculture (AA); which represent more than 88% of the regional territory (1066.03 km2). We used 2014 and 2021 Landsat 8 OLI images with topographic and atmospheric correction, in order to develop an inventory of albedo values for each land cover type in both time scenarios. Albedo images were generated by using the equation proposed by Liang in 2001, which is based on the reflectance of the bands 2, 3, 4, 5, and 7. Differences in albedo values were calculated between the years 2014 and 2021, and those differences were correlated with variations in climate parameters, for which we used climate data derived from the WRF model. In addition, the different land use changes found were classified in terms of triggers for increasing or decreasing surface albedo. Results showed that between 2014 and 2021, at least 38 events of land use change or deforestation occurred, with albedo increments between 1 and 11%, which triggered an average increment of 0.57% of the regional surface albedo in comparison to 2014 scenario. From 2014 to 2021, the albedo for CF, OGW, and AA, increased significantly (p&lt;0.001; Mann-Whitney U Test) by 79, 12, and 9%, respectively. In addition, the regional albedo increment was found to be significant and negatively correlated (p&lt;0.01 Spearman’s coefficient) with relative humidity (RH), maximum temperature (Tmax), minimum temperature (Tmin), and diurnal thermal range (DTR). The decrease in the regional values of relative humidity in 2021, occurred even when in that year the annual precipitation levels were higher than those of 2014, hence, reinforcing the fact of a possible climatic effect of the regional albedo changes. Conversion of CF and OGW into AA, perennial agriculture (PA), or grassland (GR) always yielded an albedo increment, whilst the conversion of AA to irrigation agriculture or PA triggered a decrease in albedo, and finally, the pass from GR or AA to protected agriculture caused albedo increase or decrease, depending on the greenhouse covers materials. Reducing deforestation of CF and OGW, conversion of AA or GR into PA, and selecting adequate greenhouse covers could help to mitigate regional climate change.

Hydrogen fuel is gaining particular attention in internal combustion engines. In addition to zero-carbon emissions, major advantages relate to its combustion characteristics, which allow significant increase in thermal efficiency under ultra-lean operation and with very low NOx levels. The ignition system is one of the main technology enablers, as it determines the capability to control ultra-lean operations, avoid backfire phenomena, or reduce the risks of abnormal combustions. The latter results from the hydrogen low ignition energy and it is associated with factors like high-temperature residuals, hot spots, and irregular spark plug discharge. ACIS gen 2-Barrier Discharge Igniter excels in accelerating the initial flame growth speed by the generation of non-equilibrium low-temperature plasma, strong ignition promoter for the combined action of kinetic and thermal effects. Moreover, its volumetric discharge facilitates combustion initiation on a wide region, in contrast to the localized ignition of traditional spark systems. In this work we present for the first time, to the best of our knowledge, experimental results showing the performance of a hydrogen engine with a low-temperature plasma discharge. Tests were conducted on a single-cylinder research engine, achieving ultra-lean conditions with cycle-to-cycle variability results below 2.5%. The analysis indicates that the H2 - BDI combined solution is capable of accelerating the evolution of the flame front compared to traditional spark plugs, leading to a significant reduction in the cycle-to-cycle variability. A meticulous adjustment of the BDI control parameters further enhances igniter performance and contributes to a deeper understanding of the innovative approach proposed in this study.

Current lines of research into mood disorders indicate that immune mediators participating in the pathophysiology of chronic somatic disorders have potent influences on brain functions, even when these mediators are produced in peripheral tissues. Elevated levels of circulating immune molecules have been consistently associated with depressive symptoms in a number of clinical populations and experimental models, to the extent that major depressive disorder (MDD) is now seen, at least in part, as a disorder of immunity. This paradigm has brought to the fore the use of anti-inflammatory therapies as adjunctive to standard antidepressant therapy with the hope to improve treatment efficacy, particularly in those cohorts that do not respond well to standard medication. Such new practice requires the availability of biomarkers to tailor these new therapies to those most likely to benefit but also clear mechanisms of action describing the interaction between peripheral immunity and brain function. These mechanisms are generally studied in preclinical models that try to recapitulate the human disease through peripherally induced sickness behaviour as the model for immune-induced MDD. After an appraisal of the data in rodent models and their adherence to the data in clinical cohorts, we propose a modified model of periphery-brain interaction that goes beyond the currently established view of interaction between peripheral cytokines and microglia cells as the driver of depression. Instead, we suggest that brain barriers are primary actors in the communication between body and brain and, as a consequence, in the pathophysiology of the disease. This model suggests novel biomarkers, novel targets for therapies as well as a novel mechanism for resistance to standard treatments.

Novel sensing technologies for liquid biopsies offer a promising prospect for the early detection of metabolic conditions through -omics techniques. Indeed, high-field NMR facilities are routinely used for metabolomics investigations on a range of biofluids in order to rapidly recognize unusual metabolic patterns in patients suffering from a range of diseases. However, these techniques are restricted by the prohibitively large size and cost of such facilities, suggesting a possible role for smaller, low-field NMR instruments in biofluid analysis. Herein we describe selected biomolecule validation on a low-field benchtop NMR spectrometer (60 MHz), and present an associated protocol for the analysis of biofluids on compact NMR instruments. We successfully detect common markers of diabetic control at low-to-medium concentrations through optimized experiments, including glucose (≤ 2.6 mmol./L) and acetone (25 μmol./L), and additionally in readily-accessible biofluids. We present a combined protocol for the analysis of these biofluids with low-field NMR spectrometers for metabolomics, and offer a perspective on the future of this technique appealing to point-of-care applications.

In this article we report the first investigation over time of the atmospheric conditions around TGFs occurrence, using GPS sensors in combination with geostationary satellite observations and ERA5 reanalyses data. The goal is to understand which characteristics are favourable to the development of these events and to investigate if any precursor signals can be expected. A total of 9 TGFs, occurred at a distance lower than 45 km from a GPS sensor, were analysed and two of them are shown here as an example analysis. Moreover, the lightning activity, collected by the World Wide Lightning Location Network (WWLLN) was used in order to identify any links and correlations with TGF occurrence and PWV trends. The combined use of GPS and the stroke rate trends identified, for all cases, a recurred pattern in which an increase of PWV is observed on a timescale of about two hours before the TGF occurrence that can be placed within the lightning peak. The temporal relation between the PWV trend and TGF occurrence is strictly related to the position of GPS sensors in relation to TGF coordinates. The life cycle of these storms observed by geostationary sensors, described TGFs producing clouds as intense with a wide range of extensions and, in all cases, the TGF is located at the edge of the convective cell. Furthermore, the satellite data give an added value in associating the GPS water vapor trend to the convective cell generating the TGF. The investigation with ERA5 reanalyses data showed that TGFs mainly occur in convective environment with not exceptional values with respect to the monthly average value of parameters measured in the same location. Moreover the analysis showed the strong potential of the use of GPS data for the troposphere characterization in areas with complex territorial morphology. This study provided indications on the dynamics of convective systems linked to TGFs and will certainly help refine our understanding on their production highlights a potential approach through the use of GPS data to explore the lightning activity trend and the TGFs occurrence.

We investigate the use of amplitude amplification on the gate-based model of quantum computing as a means for solving combinatorial optimization problems. This study focuses primarily on QUBO (quadratic unconstrained binary optimization) problems, which are well-suited for qubit superposition states. Specifically, we demonstrate circuit designs which encode QUBOs as ‘cost oracle’ operations UC, which when combined with the standard Grover diffusion operator Us lead to high probabilities of measurement for states corresponding to the optimal and near optimal solutions. In order to achieve these probabilities, a single scalar parameter ps is required, which we show can be found through a variational quantum-classical hybrid approach.

There is a large body of research on determining the impact of field variability of soil on crop yields. In contrast, site-specific information about crop responses to agronomic treatments is less frequent. On-Farm Precision Experimentation (OFPE) brings important information to understand the spatial variation of crop response to agronomic practices and thus to improve agronomic decisions. The objective of this work was to investigate the spatial variability of corn yield responses to nitrogen and seed rates using OFPE in four fields in the US Midwest. Geographically weighted regression was applied to generate local regression coefficients, which were used to delineate response zones in each field. The results showed the existence of great potential to adjust the rates of these inputs according to the response of each zone identified by the proposed method. The results of this study can be applied to reevaluate expectations on variable rate prescriptions guided largely by soil and variability.

A number of decision support tools facilitating the use of Electric Vehicles (EVs) have been recently developed. Due to the EVs’ limited autonomy, routing and path planning are the main challenges treated in such tools. Specifically, determining at which Charging Stations (CSs) to stop, and how much the EV should charge at them is complex. This complexity is further compounded by the fact that charging times depend on the CS technology, the EV characteristics, and follow a nonlinear function. Considering these factors, we propose a path planning methodology for EVs with user preferences, where charging is performed at public CSs. To achieve this, we introduce the Electric Vehicle Shortest Path Problem with time windows and user preferences (EVSPPWP) and propose an efficient solution algorithm for it. Given an origin and a destination, the algorithm prioritizes CSs close to Points of Interest (POIs) that match user inputted preferences, and user-defined time windows are considered for activities such as lunch and spending the night at hotels. The algorithm produces flexible solutions by considering clusters of charging points (CPs) as separate CSs. Furthermore, the algorithm yields resilient paths by ensuring that recommended paths have a minimum number of CSs in their vicinity. The main contributions of our methodology are: modeling user-defined time windows, including user-defined weights for different POI categories, creating CSs based on clusters of CPs with sufficient proximity, using resilient paths, and proposing an efficient algorithm for solving the EVSPPWP. To facilitate the use of our methodology, the algorithm was integrated into a web interface. We illustrate the use of the web interface, giving usage examples and comparing different settings.

The coronavirus disease 2019 (COVID-19) pandemic is the defining global health and socioeconomic crisis of our time and represents the greatest challenge faced by the world since the end of the Second World War. The academic literature indicates that climatic features, specifically the temperature and absolute humidity, are very important factors affecting infectious pulmonary disease epidemics (e.g., SARS, MERS); however, the influence of climatic parameters on COVID-19 remains extremely controversial. The goal of this study is to quantify the existing relationship between several daily climate parameters (temperature, relative humidity, accumulated precipitation, solar radiation, wind direction and intensity, and evaporation), local morphological parameters, and new daily positive swabs for COVID-19, which represents the only parameter that can be statistically used to quantify the pandemic. The daily deaths parameter was not considered because it is not reliable due to frequent administrative errors. Daily data on meteorological conditions and new cases of COVID-19 were collected for the Lombardy area from March 1, 2020, to April 20, 2020. This region in Italy exhibited the largest number of official deaths in the world per million inhabitants, with a value of approximately 1700 per million on june 30, 2020. Moreover, the apparent lethality was approximately 17% in this area, mainly due to the considerable housing density and the extensive presence of industrial and craft areas. The Mann-Kendall test and multivariate statistical analysis showed that none of the considered climatic variables exhibited statistically significant relationships with the epidemiological evolution of COVID-19, at least in the spring months in temperate subcontinental climate areas, with the exception of solar radiation, which was directly related and showed an otherwise low explained variability of approximately 20%. Furthermore, the average temperatures of two highly representative meteorological stations of Molise and Lucania, the most weakly affected by the pandemic. The temperatures at these stations were approximately 1.5°C lower than that in the cities in Lombardy of Bergamo and Brescia, again confirming that a significant relationship between the increase in temperature and decrease in virology from COVID-19 was not evident, at least in the Italian peninsula.

Cities consume over 75% of natural resources, produce over 50% of global waste and emit 60 - 80% of greenhouse gases. The scenario that by 2050 two thirds of the world population will live in cities, highlights how cities are still responsible of the growing consumption characterized by linear economy processes, with the production of various types of waste. In this unsustainable framework, the Circular Economy offers the opportunity to shape the urban system by means of rethinking the possibility to produce and use goods and services exploring new ways to ensure long-term prosperity. The Circular City paradigm contains in fact all the principles of the Circular Economy: recovery, recycling and sharing. In particular, Circular City also introduces actions related to the development of renewable energy communities, use of green materials, CO2 absorption approaches and Proximity Cities. The aim of this work is to develop a methodology to build a composite index (Circular City Index) capable of measuring the degree of implementation of urban policies that enable the territory to initiate an ecological transition of public assets. The city of Cagliari (Sardinia, Italy) represents the case study to apply circular urban policies in public properties, for civil and military use.

New series of compounds containing both heterocycle moieties and pseudo-symmetric hydroxyethylamine core were obtained using a simple synthetic path that can provide a library of compounds in few steps and high yields. Furthermore, diversity-oriented synthesis was studied to change different functionalities according to needs. The in vitro inhibition activity against recombinant HIV-1 protease was evaluated. A beneficial effect of this class of compounds can be obtained either for the presence of a bis-benzyl group into the core and for the heterocyclic moiety in P1, specifically the indole ring. Docking analysis was also reported.