Organophosphate pesticides (OPs) are toxic substances that contaminate aquatic environments, interfere with the development of the nervous system, and induce Neurodevelopmental Toxicity (NDT) in animals and humans. The canonical mechanism of OP neurotoxicity involves the inhibi-tion of acetylcholinesterase (AChE), but other mechanisms non-AChE are also involved and not fully understood. We used network toxicology and molecular docking to identify molecular targets and toxicity mechanisms common to OPs. Targets related to diazinon-oxon, chlorpyrifos oxon, and paraoxon OPs were predicted using the Swiss Target Prediction and PharmMapper databases. Targets related to NDT were compiled from GeneCards and OMIM databases. In order to construct the protein-protein interaction (PPI) network, the common targets between OPs and NDT were imported into the STRING. Networks topological analyses identified EGFR, MET, HSP90AA1, and SRC as hub nodes common to the three OPs. Using Reactome pathway and gene ontology we found that signal transduction, axon guidance, cellular responses to stress, and glutamatergic signaling activation play key roles in OP-induced NDT.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

Ethical considerations regarding our treatment of animals have gained strength, leading to legislation and a societal focus across various disciplines. This is a subject of study within curricula related to agri-food sciences. The aim was to determine the perceptions of agronomy university students concerning animal welfare in livestock production systems. A survey was conducted to encompass various aspects, from participants' sociodemographic attributes to their attitudes and behaviors regarding animal welfare and the consumption of animal products. Statistical analysis, performed using R software, delved into the associations between participants' characteristics and their perspectives on the ethical, bioethical, and legal dimensions of animal welfare. Associations between demographic factors and ethical viewpoints among students were identified. Gender differences emerged in animal treatment perceptions, while rural and urban environments impacted perspectives on various animals. Bioethical considerations revealed distinctive disparities based on gender and education in concerns for animal welfare, value perceptions, evaluations of animal behaviors, and opinions on animal research. It is crucial to distinguish between animal welfare and ethical considerations arising from coexisting with sentient beings capable of experiencing suffering. Ethical theories provide a lens through which we perceive our obligations toward animals. The responsibility to ensure animal welfare is firmly rooted in recognizing that animals, like humans, experience pain and physical suffering. Consequently, actions causing unjustified suffering or mistreatment, particularly for entertainment purposes, are considered morally unacceptable.

Deep eutectic solvents (DESs) are one of the most rapidly evolving types of solvents, appearing in a broad range of applications such as nanotechnology, electrochemistry, biomass transformation, pharmaceuticals, membrane technology, biocomposite development, modern 3D-printing, and many others. The range of their applicability continues to expand, which demands the development of new DESs with improved properties. To do so requires an understanding of the fundamental relationship between the structure and properties of DESs. Computer simulation and machine learning techniques provide a fruitful approach as they can provide predictions, reveal physical mechanisms and readily be linked to experiments. This review is devoted to the computational research of DESs and describes technical features of DES simulations and the corresponding perspectives on various DES applications. The aim is to demonstrate the current frontiers of computational research of DESs and discuss future perspectives.

Resumo: Este estudo teve como objetivo avaliar a Saúde Mental Positiva (SPM) e a sua relação com características sociodemográficas, literacia em saúde mental e escala de vulnerabilidade psicológica (PVS) em estudantes universitários portugueses com idades compreendidas entre os 17 e os 62 anos. Foi realizado um estudo descritivo-correlacional. Uma pesquisa online foi realizada para avaliar variáveis ​​demográficas, e vários questionários foram aplicados para avaliar saúde mental positiva, vulnerabilidade psicológica e alfabetização em saúde mental. Os dados foram coletados de 1º de novembro de 2019 a 1º de setembro de 2020. No geral, 3.405 alunos participaram do estudo. Os resultados mostram que 67,8% dos alunos revelaram um alto nível de PMH, 31,6% apresentaram um nível médio de PMH e 0,6% apresentaram um nível baixo de PMH. Os estudantes do sexo masculino relataram maior satisfação pessoal (t (3170) = -2,39, p=0,017) e autonomia (t (3170) = -3,33, p=0,001), no PMH em relação ao sexo feminino. Alunos sem bolsa pontuaram mais alto (t (3.127) = -2,04, p=0,42) no PMH do que alunos com bolsa. Estudantes que não foram deslocados de casa relataram maior (t (3170) = -1,99, p=0,047) Autocontrole em PMH do que aqueles deslocados de sua casa. Estudantes universitários com resultados de PMH mais altos têm resultados de PVS mais baixos e resultados de Alfabetização mais altos. Os achados deste estudo contribuirão para identificar as necessidades de intervenção dos alunos na PMH. Estudantes universitários com resultados de PMH mais altos têm resultados de PVS mais baixos e resultados de Alfabetização mais altos. Os achados deste estudo contribuirão para identificar as necessidades de intervenção dos alunos na PMH. Estudantes universitários com resultados de PMH mais altos têm resultados de PVS mais baixos e resultados de Alfabetização mais altos. Os achados deste estudo contribuirão para identificar as necessidades de intervenção dos alunos na PMH.

Primary energy consumption is one of the key drivers of global CO₂ emissions that, in turn, heavily depend on the efficiency of involved technologies. Either the improvement in technology efficiency or the expansion of non-fossil fuel consumption require large investments. The planning and financing of such investments, by policy makers or global energy firms, require, in turn, reliable measures of associated global spreads and their evolution in time. In this paper, our main contribution is the introduction of index measures for accessing global spreads (that is, measures of inequality or inhomogeneity in the statistical distribution of a related quantity of interest) of technology efficiency and CO₂ emission in primary energy consumption. These indexes are based on the Gini index, as used in economical sciences, and generalised entropy measures. Regarding primary energy sources, we consider petroleum, coal, natural gas and non-fossil fuels. Between our findings, we attest some stable relations in the evolution of global spreads of technology efficiency and CO₂ emission, and a positive relation between changes in global spreads of technology efficiency and use of non-fossil fuel.

Poly(vinylidene fluoride) nanocomposites processed with different morphologies, such as porous and non-porous films and fibres, have been prepared with silica nanoparticles (SiNPs) of varying diameter (17, 100, 160 and 300 nm) which in turn have encapsulated perylenediimide (PDI), a fluorescent molecule. Structural, morphological, optical, thermal, and mechanical properties of the nanocomposites, with SiNP filler concentration up to 16 wt% were evaluated. Further, cytotoxicity and cell proliferation studies were performed. All SiNPs are negatively charged independently of the pH and more stable from pH 5 upwards. The SiNPs introduction within the polymer matrix increases the contact angle independently of the nanoparticle diameters and the smallest ones (17 nm) improve the PVDF Young modulus from 0.94 ± 0.04 GPa for the pristine polymer film to 1.05 ± 0.06 GPa. Varying filler diameter, physico-chemical, thermal and mechanical properties of the polymer matrix were not significantly affected. Finally, the SiNPs inclusion does not induce cytotoxicity in murine myoblasts (C2C12) after 72 h of contact and proliferation studies reveal that the prepared composites represent a suitable platform for tissue engineering applications, as they allow to combine the biocompatibility and piezoelectricity of the polymer with the possible functionalization and drug encapsulation and release of the SiNP.

This article discusses collaborative ethnography as a meaningful source for spatial research, in particular, for participatory methodologies in urban planning and placemaking processes. It investigates the experiences with co-creation and co-research in different research projects to gain insight into the performance of collaborative ethnography as a technique to explore and enrich local knowledge. To better understand the possible causal relationships between the experience gained in the projects and the learnt lessons, we also identify recommendations for improving research methodologies to be applied in placemaking. The article concludes that collaborative ethnography is an effective tool for adding value to spatial co-research and co-creation processes. It opens opportunities for the co-production of space, ideas and knowledge, contributing at the same time to better informed decision-making. It also helps improve ideas and gather insights into the spatial needs of focus groups.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

ABSTRACT: Psychological vulnerability (PV) and low mental health literacy correlate negatively with higher education students' positive mental health and health behaviours. Levels of mental health literacy limit self-help, adaptative coping strategies and academic success. However, few studies examine the significant differences between students' PV, mental health literacy, positive mental health (PMH) and modifiable behaviours variables. Identifying modifiable vulnerability factors is essential when seeking and providing professional help. Method: A cross-sectional descriptive study was conducted to investigate the differences between modifiable behaviours and PV, mental health literacy, and PMH in higher education students. A sample of 3,600 undergraduate students was recruited, mostly female (78.8%), with an average age of 23 years (SD = 6.68). Results: The majority were women, did not exercise, were dissatisfied with sleep quality time per night (62.1% sleep less than 7 hours per night) and did not engage in leisure activities. Also, most respondents had PV and low literacy levels, particularly at F1, and 67.9% scored in the flourishing group. Results showed significant differences (p<0.001) between gender, age, sleep, exercise, diet, leisure activities and PV, and PMH and literacy. Conclusions: The results identified modifiable vulnerability factors that underpin the design of intervention-targeted programmes to promote literacy and PMH in higher education campuses in Portugal to foster students’ well-being and self-help strategies.

Understanding how humans perceive animals is important for biodiversity conservation, however, only a few studies about this issue were carried out in South America. We selected two Brazilian cities to assess people’s perceptions of birds: Bauru (São Paulo, Brazil) and Belo Horizonte (Minas Gerais, Brazil). From the bird data we gathered, we developed a questionnaire and applied it between September 2020 and June 2021. The data obtained were analyzed by simple counts, Likert scale, and percentages. Also, open questions were placed on the Free Word Cloud Generator website. Our study confirmed that most respondents are aware of the importance of birds to ecological balance and that respondents had a generally positive attitude towards most of the bird species. However, they disliked exotic species such as the Domestic Dove and the House Sparrow, which are associated with disease, dirt, and disgust. Respondents also underestimated the number of birds that can live in urban areas and the song of birds is still a sense less explored and perceived by people. The concept of environmental perception seeks to cover aspects and understanding these human–biodiversity relationships is essential to successfully guide public policies, urban planning interventions, and environmental education activities.

Evaluating the economic impact of airports is crucial for understanding the benefits they bring to a region. However, when an area has more than one airport, it becomes essential to analyze each airport's contribution to the local economy to make informed investment and policy decisions. Thus, studying economic models that can distinguish each airport's impact on the region's economy becomes essential. In this context, this paper aims to compare three different approaches to determine the economic contribution of airports in a given region and identify their social and economic benefits. The International Civil Aviation Organization recommends using Input-Output analysis in this context. The study considered three weight factors for the Input-Output basic model: circular buffer, displacement time, and Huff's gravitational model. The analysis was performed using the three largest airports in São Paulo's state, Brazil, due to their proximity and influence on the surrounding area. The models were compared based on their efficiency and accuracy in reflecting the reality of the case study context. The study identified the most suitable model for establishing correlations between investments made in airport infrastructure and the generation of gross domestic product, employment, and added value. This study fills a gap in the existing literature by proposing improvements to the methods for evaluating airports' economic and social benefits. In recent times, airport investors, both in the government and private sectors, have become increasingly demanding in their need for accurate analyses before making investments. Therefore, the results of this paper will provide valuable insights into the benefits of investing in airport infrastructure and help policymakers and investors make informed decisions.

The links between rural and urban have often been the subject of study in Portugal. Nevertheless, the asymmetries between rural and urban have not ceased to increase over the last decades, contributing to an imbalance of economic, social, and territorial dimensions between regions. In order to counter this trend, policies to attract the population and tourism have been endorsed but have not been sufficient to promote territorial cohesion. This makes it necessary to rethink the capacity and the potential of rural territories in terms of mobilising their resources and, through them, promoting new and/or renewed relations with urban territories. This article aims to explore and map the links between urban and rural areas by analysing the routes taken by agri-food products, from production to marketing, with the support of a spatial analysis, using Geographic Information Systems (GIS). For that, we analysed a set of specialised and/or gourmet shops in Oorto and Lisbon, and their relations with the territories from which the commercialized agri-food products come. Most of these products originate in the inland rural regions of the country, and there is a clear geographical connection between the shops analysed and specific territories. Thus, it was possible to verify the increase in interest and consumption of agri-food products of rural origin and the spontaneous increase of this type of shop in the cities analysed, as well as identify the target audience of the shops and the spatial influence they have in the respective cities. These shops, in addition to selling agro-food products, are also promoters of rural territories in an urban environment.

Immersive Unit Visualization is an emergent form of visualization that arose from Immersive Analytics where, unlike traditional visualizations, each data point is represented by an individual visual mark in an immersive virtual environment. This practice has focused almost exclusively on virtual reality, excluding augmented reality (AR). This article develops and tests a prototype of an immersive Unit Visualization (Floating Companies II) with two AR devices: head-mounted display (HMD) and hand-held display (HHD). Results from the testing sessions with 20 users were analyzed through qualitative research analysis and thematic coding indicating that, while the HHD enabled a first contact with AR visualization on a familiar device, HMD improved the perception of hybrid space by supporting greater stability of virtual content; wider field of view; improved spatial perception; increased sense of immersion; and more realistic simulation, which impacted on information reading and sense-making. The materialization of abstract quantitative values into concrete reality through its simulation in the real environment and the ludic dimension stand out as important opportunities of this type of visualization. This paper investigates the aspects distinguishing two experiences regarding data visualization in hybrid space; and characterizes ways of seeing information with AR, identifying opportunities to advance information design research.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

Changes in food quality can dramatically impair zooplankton fitness, especially in eutrophic water bodies where cyanobacteria are usually predominant. Cyanobacteria are considered a food with low nutritional value, besides some species can produce bioactive secondary metabolites reported as toxic to zooplankton. Considering that cyanobacteria can limit survival, growth and reproduction of zooplankton, we hypothesized that the adverse effects of the dietary exposure of Daphnia species to saxitoxin-producing cyanobacteria depend on the relative abundance of nutitious food source in the diet. Life table experiments were conducted with different diets: 1) without nutritional restriction, where neonates were fed with diets at a constant green algae (Monoraphidium capricornutum) biomass as a nutritious food source, and increasing cyanobacterial concentration (STX-producing Raphidiopsis raciborskii), and 2) with diets consisting of different proportions of M. capricornutum (nutritious) and R. raciborskii (poor food) at a total biomass 1.0 mg C L 1. In general, the presence of high proportions of cyanobacteria promoted a decrease in Daphnia somatic growth, reproduction and intrinsic rate of population increase (r) in both diets with more pronounced effects in the nutritionally restricted diet (90% R. raciborskii). Two-way ANOVA revealed significant effects of species/clone and treatments in both assays, with significant interaction between those factors only in the second assay. Regarding the grazing assay, only D. laevis was negatively affected by increased cyanobacterial proportions in the diet. In the life table assay with constant edible food, a reduction in the reproduction parameters and the intrinsic rate of population increase (r) of all species was observed, In conclusion, we found adverse effects of the toxic cyanobacterial strain R. raciborskii on Daphnia fitness, regardless of the constant amount of nutritious food available, proving the toxic effect of R. raciborskii and the nutritional quality of the food has a greater influence on the fitness of these animals.

Forest ecosystems are important providers of ecosystem functions and services belonging to four categories: supporting, provisioning, regulating, and cultural ecosystem services. Forest management, generally focused on timber production, has consequences on the ability of the system to keep providing services. Silviculture, in fact, may affect ecological structures and processes from which services arise. In particular, the removal of biomass causes a radical change in the stocks and flows of energy characterizing the system. Aiming at the assessment of differences in stored natural capital and ecosystem functions and services provision, three differently managed temperate forests of common beech (Fagus sylvatica) were considered: (1) a forest in semi-natural condition, (2) a forest carefully managed to get timber in a sustainable way and (3) a forest exploited without management. Natural capital and ecosystem functions and services are here accounted in biophysical terms. Specifically, all the resources used up to create the biomass (stock) and maintain the production (flow) of the different components of the forest system were calculated. Both stored emergy and empower decrease at increasing human pressure on the forest, resulting in a loss of natural capital and a diminished ability of the natural system to contribute to human well-being in terms of ecosystem services provision.

Master Valentim’s fountain became an important historical patrimony for Brazil, being portrayed by famous artists among them Jean-Baptiste Debret. In 1938, it was registered as cultural heritage by the Brazilian National Historical and Artistic Heritage Institute (IPHAN), and in 1990 it was subjected to excavation and restoration works. The fountain was built in Gneiss and Lioz limestone, with metallic plates and mortar connecting the Gneiss blocks. Currently, deteriorations in the fountain stones can be observed such as light stains and some aesthetic modifications caused by inadequate restorations. Petrography, XRF, XRD, Physical Properties, Colorimetry, Electrical Conductivity, ICP-OES, SEM-EDX, and TGA were performed in order to characterize the Gneiss blocks, the metallic plates, the stones used in previous restorations, as well as light stains observed on the Gneiss blocks. The petrography and XRD analyses inferred that light stains may have been caused by the formation of an insoluble salt as a result of the association of the lead from the plates with other elements. The XRD analysis on the light staining area indicated presence of cerussite (PbCO₃), and anglesite (PbSO₄), which are the probable cause of the light stains. The SEM-EDX results suggested that sulfur is the main element associated to lead.

The study of photonic crystals has emerged as an attractive area of research in nanoscience in the last years. In this work we study the properties of a two-dimensional photonic crystal composed of dielectric rods. The unit cell of the system is composed of six rods organized on the sites of a C6 triangular lattice. We induce a topological phase by introducing an angular perturbation ϕ in the pristine system. The topology of the system is then determined by using the so-called k.p perturbed model. Our results show that the system presents a topological and a trivial phases, depending on the sign of the angular perturbation ϕ. The topological character of the system is probed by evaluating the electromagnetic energy density and analyzing its distribution in the real space, in particular on the maximal Wyckoff points. We also find two edge modes at the interface between the trivial and topological photonic crystals, which present a pseudospin topological behavior. By applying the Bulk-Edge correspondence, we study the pseudospin edge modes and conclude that they are robust against defects, disorder and reflection. Moreover, the localization of the edge modes leads to the confinement of light and the interface behaves as a waveguide for the propagation of electromagnetic waves. Finally, we show that the two edge modes present energy flux propagating in opposite directions, which is the photonic analogue of the quantum spin Hall effect.

A variety of bioactive substances present in fruits and vegetables processed products have health-promoting properties. Consumption of nutrient-rich plant-based products is essential to address undernutrition and micronutrient deficiencies. Preservation is paramount in manufacturing plant-based non-solid foods such as juices, purees, and sauces. Thermal processing has been widely used to preserve fruit and vegetable-based products by reducing enzymatic and microbial activities, thereby ensuring safety and prolonged shelf life. However, the nutritional value of products is compromised due to the deleterious effects of thermal treatments on essential nutrients and bioactive compounds. To prevent the loss of nutrients associated with thermal treatment, alternative technologies are being researched extensively. In studies conducted on non-solid food, UV-C treatment has been proven to preserve quality and minimize nutrient degradation. This review compiles information on the use of UV-C technology in preserving the nutritional attributes of non-solid foods derived from fruit and vegetables. Legislation, market potential, consumer acceptance, and limitations of UV-C are reviewed.

Linear programming formulations of forest ecosystem management (FEM) problems proposed in the 60s have been adapted and improved upon over the years. Generating management alternatives for forest management planning is a key step in building these models. Global forests are diverse, and a variety of models have been developed to simulate management alternatives. Climate change has made forest management calculations even more complex, requiring flexibility, diverse parameters, models, and methods. Despite this complexity, consistent concepts can be applied in developing management alternatives for forest management planning. This work describes iGen, a flexible forest prescription generator that applies the AI technique Rule-Based System (AI-RBS). iGen projects the state and associated inputs and outputs for a set of management units using rules from its knowledge base. An Inference Engine uses the rules to simulate a set of prescriptions in a tree-like graph structure. Without needing IT specialists, forest managers can describe the potential development of their forest through variables, rules, formulas, functions, and procedures. A key feature of iGen is that it is not limited to, adapted to, or focused on any specific region, landscape, forest condition, projection method, or yield function. Instead, it aims to maximize generality, enabling it to address a broad range of FEM problems. This article introduces iGen, explaining its concepts, structure, and algorithms through two FEM problems: natural regeneration with shelterwood harvests and plantation/coppice. For data and iGen source programs, visit github.com/…/iGen.

In this work, the cross-linked PMMA-based dental resins scraps were submitted to pyrolysis to recover MMA (Methylmethacrylate). The thermal degradation of cross-linked PMMA-based dental resins scraps was analyzed by TG/DTG to guide the operating conditions in pilot scale. The pyrolysis experiments carried out in a reactor of 143L, at 345, 405, and 420°C, 1.0 atmosphere. The reaction liquid products obtained at 345°C, physicochemical characterized for density, kinematic viscosity, and refractive index. The chemical composition of liquid products obtained at 345°C, 30, 40, 50, 60, 70, 80, and 110 minutes, at 405°C, 50, 70, and 130 minutes, and at 420°C, 40, 50, 80, 100, 110, and 130 minutes determined by GC-MS. The experiments show that liquid phase yields were 55.50%, 48.73%, and 48.20% (wt.), at 345, 405, and 420°C, respectively, showing a smooth sigmoid behavior, decreasing with increasing temperature, while that of gas phase were 31.69%, 36.60%, and 40.13% (wt.), respectively, increasing with temperature. The liquid products density, kinematic viscosity, and refractive index obtained at 30, 40, 50, 60, 70, 80, and 110 minutes, varied between 0.9227 and 0.9380 g/mL, 0.566 and 0.588 mm2/s, and 1.401 and 1.414, respectively, showing percentage deviations between 0.74 and 2.36%, 7.40 and 10.86%, and 0.00 and 0.92%, respectively, compared to standard values for density, kinematic viscosity, and refractive index of pure MMA at 20 °C. The GC-MS identified in the reaction liquid products at 345, 405, and 420°C, 1.0 atm, esters of carboxylic acids, alcohols, ketones, and aromatics, showing concentrations of MMA between 83.454 and 98.975% (area.). For all the depolymerization experiments, the concentrations of MMA in the liquid phase, between 30 and 80 minutes, reach purities above 98% (area.), decreasing drastically with increasing reaction time after 100 minutes, thus making it possible to depolymerize the cross-linked PMMA-based dental resins scraps by pyrolysis to recover MMA. The optimum operating conditions to achieve high MMA concentrations, as well as elevated yields of liquid reaction products were 345 °C and 80 minutes.

The separator membrane is an essential component of lithium-ion batteries, separating the anode and cathode and controlling the number and mobility of the lithium ions. Among the polymer matrices most investigated for battery separators are poly(vinylidene fluoride) (PVDF) and its copolymers poly(vinylidene fluoride-co-trifluoroethylene) (PVDF-TrFE), poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), and poly(vinylidene fluoride-cochlorotrifluoroethylene) (PVDF-CTFE), due to their excellent properties such as high polarity and the possibility of controlling the porosity of the materials through binary and ternary polymer/solvent systems, among others. This review presents the recent advances on battery separators based on poly(vinylidene fluoride) (PVDF) and its copolymers for lithium-ion batteries. It is divided in the following sections: single polymer and co-polymers, surface modification, composites and polymer blends. Further, a critical comparison between those membranes and other separator membranes is presented, as well as the future trends on this area.

Obesity is a risk factor for the development of gestational diabetes mellitus (GDM). However, the most optimal type of nutritional intervention to prevent GDM in high-risk women is not clearly defined. This study investigates if nutritional treatment based on the Mediterranean diet (MedDiet) before 12th gestational week (GW) in women at high risk due to a body mass index (BMI)≥25kg/m2, reduces the rate of GDM and metabolic syndrome (MetS) at 3 years postpartum. We performed a post-hoc analysis of the San Carlos Gestational Prevention Study. A total of 735 women with BMI≥25kg/m2 were evaluated between 2015-2018, 246 in standard diet control group (CG) and 489 in MedDiet intervention group (IG). The rate of GDM was significantly lower in IG compared to CG (25.1%vs31.7%;p=0.037). Postnatal follow-up was completed by 141 women in CG (57%) and 312 women in IG (64%). At 3 years postpartum, we observed a reduction (relative risk 95% confidence interval) in the rates of impaired fasting glucose (IFG) (0.51 (0.28-0.92);p=0.019), obesity (0.51 (0.28-0.92),p=0.041), waist circumference (WC)≥89.5cm (0.54 (0.31-0.94);p=0.022) and MetS (0.56 (0.33-0.94);p=0.003). MedDiet reduces the rate of GDM and postpartum MetS in women with BMI)≥25kg/m2, suggesting that its implementation should be routinely recommended from the first GWs.

Arboviruses have two ecological transmission cycles, sylvatic and urban. For some, the sylvatic cycle has not been thoroughly described in America. To study the role of wildlife in a putative sylvatic cycle, we sampled free-ranging bats and birds in two arbovirus endemic locations and analyzed them using molecular, serological, and histological methods. No current infection was detected, and no significant arbovirus-associated histological changes were observed. Neutralizing antibodies were detected against selected arboviruses. In bats, positivity in 34.95% for DENV-1, 16.26% for DENV-2, 5.69% for DENV-3, 4.87% for DENV-4, 2.43% for WNV, 4.87% for SLEV, 0,81% for YFV, 7.31% for EEEV, and 0.81% for VEEV was found. Antibodies against ZIKV were not detected. In birds, PRNT results were positive against WNV in 0.80%, SLEV in 5.64%, EEEV in 8.4%, and VEEV in 5.63%. An additional retrospective PRNT analysis was performed using bat samples from three additional DENV endemic sites resulting in a 3.27% prevalence for WNV and 1.63% for SLEV. Interestingly one sample resulted unequivocally WNV positive confirmed by serum titration. These results suggest that free-ranging bats and birds are exposed to not currently reported hyperendemic-human infecting Flavivirus and Alphavirus, however, their role as reservoirs or hosts is still undetermined.

This study focuses on the Cereja River, a Permanent Preservation Area located in Amazon coast. The hypothesis tested was that the water quality of the Cereja River has worsened over recent years due to unplanned urban growth. To assess changes in the water quality, seven campaigns were undertaken with data being collected at six fixed points, during two distinct periods (2013–2014 and 2018–2019). High-resolution satellite images from GoogleEarth (2012 and 2019) were used to register unplanned occupation. The DPSWR (Driver-Pressure-State-Welfare-Response) socioecological framework was used to identify potential measures for the management of environmental and anthropogenic problems. The increase in the number of households found on the Cereja margins between 2012-2019 has contributed to the river’s intense trophic condition, low concentrations of dissolved oxygen, high concentrations of pathogenic bacteria, and loss of vegetation cover. The water of the Cereja River is inadequate for any human use, and its contamination is one of the principal factors determining the reduction of the water quality of the Caeté estuary. According to the obtained results, the DPSWR model proved to be an excellent analytical tool for the evaluation of specific local scenarios, through the integrated analysis of socio-environmental issues. The scenario observed can be extrapolated to other rivers located within urban areas in the Amazon region that have relatively unplanned growth.

Adaptations to climate change rely on understanding the dynamics of plant biomass stocks on the planet. The high levels of deforestation in Cerrado have transformed this biome into the second-largest Brazilian source of carbon emissions. The objective of this study was to develop a method to accurately estimate aboveground and total biomass values among shrublands, savannas, and forests located in the Cerrado biome, using an allometric equation adjusted from canopy height, obtained through optical and laser sensors. The results show similarity between the estimates employed by our method and the data found in the literature review for different phytophysiognomies in the Cerrado biome. Shrubland formations showed higher biomass estimation uncertainties due to the discontinuity of isolated trees and the lower canopy height when compared to more clustered tree canopies in savannas and taller canopies in forests. Aboveground biomass estimates were related to expansion factors, and specific maps were developed for each compartment by root, litter, and necromass. The sum of these compartments is presented in the aboveground and below forest biomass map. This study presents, for the first time, the mapping of total biomass in 10 m pixels of all regions of the Cerrado biome.

The supply of mental health processes in primary care has gaps. This study aims to analyze the association of agreement criteria and flows between primary care teams and the Family Health Support Center (NASF) for mental health collaborative care, considering the difference between capital and non-capital cities in Brazil. This cross-sectional study was conducted based on secondary data from the Primary Care Access and Quality Improvement Program. Agreement criteria and flows were obtained from 3883 NASF teams of the matrix support or collaborative care. The Chi-square test and multiple Poisson regression were used; p &lt; 0.05 was considered statistically significant. Prevalence ratios of negative associations demonstrated protective factors for support actions: follow-up at Psychosocial Care Center, management of psychopharmacotherapy, offer of other therapeutic actions, care process for users of psychoactive substances, and offer of activities to prevent the use of psychoactive substances. Collaborative care in primary care was effective, and capital cities were a protective factor compared with non-capital cities.

Background: When homeostasis is disturbed it can occur a pathological event named inflammation. The main drugs used in the treatment consist of the non-steroidal and steroidal anti-inflammatory drugs. However, the side effects remain an obstacle during the treatments. In this work we aimed to evaluate three new regioisomers analogues of naphthyl-N-acylhydrazone derivatives. Methods: Acute models of inflammation in vivo (formalin-induced licking and carrageenan-induced inflammation) as well as in vitro were used to evaluate the effects of LASSBio-2039, LASSBio-2040, and LASSBio-2041. Results: All three substances (at 1, 10 or 30 µmol/kg) presented significant effect in the in vivo model reducing leukocyte migration, nitric oxide (NO) and interleukin-1β production. It was observed that only LASSBio-2039 significantly reduced cell migration in vitro. None of the LASSBios did affect inducible nitric oxide synthase activity nor presented NO scavenger effect. It was not observed any toxic effect neither in vivo nor in vitro. The new regioisomers analogues of naphthyl-N-acylhydrazone derivatives presented a significant anti-inflammatory activity suggesting LASSBio-2039 with a direct effect in leukocytes migratory capacity. Conclusions: Taken together the data indicate that these substances present promising effect for de development a prototype for new drugs.

Shot peening is an attractive technique for fatigue enhanced performance of metallic components, because it promotes crack initiation retardation and later crack growth. Engineering design based on fatigue crack propagation predictions applying the principles of fracture mechanics is commonly used in aluminum structures for aerospace engineering. The main purpose of present work was to analyze the effect of shot peening on the fatigue crack propagation of the 7475 aluminum alloy, under both constant amplitude loading and periodical overload blocks. The tests were performed on 4 and 8 mm thickness specimen's with stress ratios of 0.05 and 0.4. The analysis of the shot-peened surface showed a small increase of the micro-hardness values, due to the plastic deformations imposed by shot peening. The beneficial effect of surface peening on fatigue crack growth rates is quite limited to an increasing near the threshold. The specimens’ thickness has only marginal influence on the crack propagation, in opposite to the stress ratio. Periodic overload blocks of 300 cycles promotes a reduction of the fatigue crack growth rate for both intervals of 7,500 and 15,000 cycles.

This study continued the analysis of immunization with the receptor binding domain (RBD) associated with the adjuvants Dimethyldioctadecylammonium bromide (DDA) and Saponin (Sap) (RBD+DDA/Sap) or Aluminum hydroxide (AH) and outer membrane vesicles (OMVs) of Neisseria meningitidis (RBD+AH/OMV); from adult to old age and assessed maternal-fetal transference of antibodies. Outbred Swiss mice were immunized with 2 intramuscular (IM) doses with the antigenic preparations RBD+DDA/Sap, RBD+AH/OMV or RBD alone. The humoral immune response was evaluated using ELISA, avidity-ELISA, Immunoblotting and a Omicron-surrogate-neutralization assay (BA.1), while the cellular immune response was analyzed by ELISpot. Our previous work studied the IgG response; here, we verified that IgM levels were higher right after the immunization doses, but, as IgG, it persisted until 368 days after the immunization. The avidity of IgM increased from low to intermediate-to-high after the booster dose. RBD+DDA/Sap presented neutralizing indexes against Omicron at days 47 and 176, while RBD+AH/OMV showed neutralization on days 21, 47 and 176. Cellular response, measured 465 days after immunization, revealed IFN-Y and IL-4 secretion. The offspring of RBD+DDA/Sap had detectable antibodies, which decreased around 45 days after birth, the last point we analyzed. The results suggested that DDA/Sap is a promising adjuvant mixture to enhance humoral and cellular immune response against SARS-CoV-2, improving maternal-fetal transference of antibodies; cross-reactivity with Omicron variant; and the maintenance of antibodies for a long period.

Gestational diabetes mellitus (GDM) pathophysiology comprises clinical and genetic factors. In fact, GDM has been associated with several single nucleotide polymorphisms (SNPs). This study aimed to build a prediction model of GDM combining clinical and genetic risk factors. A total of 1588 pregnant women from the San Carlos Cohort participated in the present study, 1069 (67.3%) Caucasian (CAU) and 519 (32.7%) Latin American (LAT), 255 (16.1%) with GDM. The incidence of GDM was similar in both groups (16.1% CAU and 16.0% LAT). Genotyping was performed by IPLEX Mass ARRAY PCR selecting 110 SNPs based on literature references. The SNPs showing the strongest likelihood of GDM development were the rs10830963, rs7651090 and rs1371614 in CAU and rs1387153 and the rs9368222 in LAT. Clinical variables including age, pre-pregnancy body mass index and fasting plasma glucose (FPG) at 12 gestational weeks predicted the risk of GDM (AUC 0.648, 95%CI 0.601-0.695 in CAU; AUC 0.688, 95%CI 0.628-9.748 in LAT) and adding the SNPs modestly improved prediction (AUC 0.722, 95%CI 0.680-0.764 in CAU; AUC 0.769, 95%CI 0.711-0.826 in LAT). In conclusion, adding genetic variants enhanced the prediction model of GDM risk in CAU and LAT pregnant women. An RCT is underway to demonstrate its usefulness

Background and Objectives: Mechanical and biological complications can lead to system fracture or screw loss on dental implants. Narrow and regular platforms have been used without a consensus about the effect of distance the abutment from the prosthetic platform margin. The aim of this study is to evaluate different insertion torques in the deformation of tri-channel platform connections through two- and three-dimensional measurements with micro-CT. Materials and Methods: 164 implants were divided into groups (platform diameter and type): 3.5, 3.75, and 4.3 mm NP (Narrow Platform), and 4.3 mm RP (Regular Platform). Each implant-platform group was then divided into four subgroups (n = 10) with different torques: T45 (45 Ncm), T80 (80 Ncm), T120 (120 Ncm) and T150 (150 Ncm). The implant-abutment-screw assemblies were scanned and the images obtained were analyzed. Results: A significant difference was observed for the linear and volume measures between the different platforms (p &lt;0.01) and the different implant insertion torques (p &lt;0.01). Qualitative analysis suggested higher deformation resistance for the 3.75 NP compared to the 3.5 NP, and RP was more resistant compared to the NP. Conclusions: The 0.25-mm increment in the implant platform did not increase the resistance to the applied insertion torques; the 4.3-mm implant was significantly stronger compared to the 3.5-mm implant and the proposed micro-CT analysis was considered valid for both 2D and 3D analyses of micro gaps, qualitatively and quantitatively.

The phytonutraceutical Ormona® is a product composed of: purified oil of Bixa orellana Linné; dry extract of Myrciaria dubia McVaugh; dry extract of Trifolium pratense L. and dry extract of Euterpe oleracea Mart. obtained using Evolve® technology. This study evaluated the effects of Ormona® on Wistar rats affected by ovariectomy-induced osteoporosis. Pre-treatment was conducted for 15 days before surgery and continued for a further 45 days after the surgical procedure. The experimental design consisted of 5 groups (n=5): OVW: treated with distilled water (1 mL/ kg, p.o); ADS: alendronate sodium (4 mg/ kg p.o); EST: conjugated estrogen (2 ug/ kg, p.o); ORM: Ormona® (20 mg/kg, p.o); ORM + EST: Ormona® (20 mg/kg + conjugated estrogen 2 ug/ kg, p.o. Biochemical and hormonal parameters, along with bone histopathology and trabecular and femoral diaphysis size, were evaluated through Scanning Electron Microscopy (SEM) and bone calcium quantification by atomic absorption spectrophotometry. The results show that ovariectomy caused bone alterations such as loss of femoral microarchitecture, decreased bone homeostasis parameters, and changes in the lipid profile. Estrogen supplementation reduced parameters such as cholesterol, LDL, and Ca2+ concentration. However, Ormona® showed higher serum estradiol levels (p&lt; 0.01), effects on the lipid profile, including parameters that estrogen replacement and alendronate sodium did not affect, with an increase in HDL, and positive modulation of bone metabolism, increasing osteocytes and the presence of osteoblasts. Ormona®, therefore, produced better results than the groups treated with estrogen and alendronate sodium.

Abstract: Passive acoustic monitoring (PAM) is a non-invasive technique to supervise the wildlife. Acoustic surveillance is preferable in some situation such as in the case of marine mammals, when the animals spend most of their time underwater, making it hard to obtain their images. Machine learning is very useful for PAM, for example, to identify species based on audio recordings. But some care should be taken to evaluate the capability of a system. We define PAM-filters as the creation of the experimental protocols according to the dates and locations of the recordings, aiming to avoid the use of the same individuals, noise and recording devices in both training and test sets. A random division of a database present accuracies much higher than accuracies obtained with protocols generated with PAM-filter. Although we use the animal vocalizations, in our method we convert the audio into spectrogram images, after that, we describe the images using the texture. Those are well-known techniques for audio classification, and they have already been used for species classification. Also, we perform statistical tests to demonstrate the significant difference between accuracies generated with and without PAM-filters with several well-known classifiers. The configuration of our experimental protocols and the database were made available online.

Leishmaniasis are neglected diseases that affect regions such as South Asia, South Africa and Latin America, less developed regions. Current treatment, for cutaneous, mucocutaneous and visceral leishmaniosis, which are the main forms of the disease, is based on the administration of pentavalent antimonial and amphotericin B. However, these drugs have low efficacy and high toxicity. For this reason, the search for new treatments for this disease is necessary, based on studies of new molecules and their conformations. The research proposed the conformational study of brominated guanidine compounds with potential antileishmanial activity using Nuclear Magnetic Resonance (NMR) and X-ray diffraction (XRD) techniques. The present study involves the bro-minated molecules, LQOF-G2, LQOF-G30, LQOF-G35 and LQOF-G35-Br. The later was synthesized by the reaction of LQOF-G35 with NBS under IR irradiation at 120 Watts of potency and dichloro-methane as solvent by 12-h of exposition. The obtained results demonstrated the efficiency of the bromination method, since two bromines atoms entered the molecule. Furthermore, NMR analysis showed the occurrence of a conformational change from Z to E when compound LQOF-G35 was brominated to LQOF-G35-Br. This feature was well confirmed by comparative DRX study of the LQOF-G35 and LQOF-G35-Br compounds. The antileishmanial activity of LQOF-G2 e LQOF-G35 motivated the synthesis of new brominated compounds LQOF-G30 e LQOF-G35-Br.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

Starting 1994, the debate for regulating organic agriculture in Brazil was officially recognized in May 1999. Still, only in 2003, when the law # 10,831 was instituted, the country reached an effective milestone on organic production, both internally and externally. Since the industry regulation, the legislation underwent many modifications, constantly reviewing and adjusting. The current study examined the institutionalization of organic production in Brazil and what the current regulations can be used as a reference for those interested in this sector. The most recent update of Organic legislation and its implication on practice were also discussed. A case study on production of strawberry in organic system is presented and discussed.

Visible and near-infrared reflectance (Vis–NIR) techniques are a plausible method to soil analyses. The main objective of the study was to investigate the capacity to predicting soil properties Al, Ca, K, Mg, Na, P, pH, total carbon (TC), H and N, by using different spectral (350–2500 nm) pre-treatments and machine learning algorithms such as Artificial Neural Network (ANN), Random Forest (RF), Partial Least-squares Regression (PLSR) and Cubist (CB). The 300 soil samples were sampled in the upper part of the Itatiaia National Park (INP), located in Southeastern region of Brazil. The 10 K-fold cross validation was used with the models. The best spectral pre-treatment was the Inverse of Reflectance by a Factor of 104 (IRF4) for TC with CB, giving an averaged R² among the folds of 0.85, RMSE of 1.96; and 0.67 with 0.041 respectively for H. Into the K-folds models of TC, the highest prediction had a R² of 0.95. These results are relevant for the INP management plan, and also to similar environments. The good correlation with Vis–NIR techniques can be used for remote sense monitoring, especially in areas with very restricted access such as INP.

ABSTRACT: Charismatic species, like the panda, play an important role in conservation, and velvet worms arguably are charismatic worms. Thanks to their extraordinary hunting mechanism, they have inspired from a female metal band in Japan, to origami worms in Russia and video game monsters in the USA. Objective: To assess their conservation status in Costa Rica. Methods: we located all collection records of the 29 known species from the Onychophora Database in the map of the Costa Rican Conservation Network. Results: We found that seven species are protected inside forest reserves, five in Protected Zones, four in Wildlife Refuges, two in National Parks and one, Principapillatus hitoyensis, in a strictly pristine Biological Reserve. The largest species in the world, Peripatus solorzanoi, occurs both inside a Forest Reserve and in protected private land. Protection inside Costa Rican nature areas is enforced year round by personnel that includes armed guards, and is supported by educational programs in surrounding communities. Twelve species have not been found in protected areas, but in Costa Rica, all biological species, named and unnamed, are protected by law and cannot be legally collected, or exported, without technically issued permits. Conclusion: Like in the only other country with similar information (New Zealand), the conservation of onychophorans seems to be of least concern for at least two thirds of the known species. Epiperipatus isthmicola, recently rediscovered after a century of absence in collections, can be considered Threatened because nearly all of its natural habitat has now been covered by a city.

In this work a new hydroelectric basin modelling approach is described and applied to the Pontecosi basin, Italy. Several types of data sources were used to learn the model: a number of weather stations, satellite observations, Reanalysis dataset and basin data. With the goal of predicting the water level of the basin, the model was composed by three cascade modules. Firstly, different spatial interpolation methods, such as Kriging, Radial Basis Function and Natural Neighbours, were compared and applied to interpolate the weather stations data nearby the basin area to infer the main environmental variables (air temperature, air humidity, precipitation and wind speed) in the basin area. Then, using these variables as inputs, a neural network was trained to predict the mean soil moisture concentration over the area, also to improve the low availability due to satellite orbits. Finally, a non-linear auto regressive exogenous input (NARX) model was trained to simulate the basin level with different prediction horizons, using the data from the previous modules and past basin data (water level, discharge flow rate, turbine flow rate). Accurate predictions of the basin water level were achieved within 1 to 6 hours ahead, with mean absolute errors (MAE) between 2cm and 10cm respectively.

Ucuùba fat is fat obtained from a plant found in South America, mainly in Amazonian Brazil. Due to its biocompatibility and bioactivity, the Ucuùba fat was used for production of ketoconazole-loaded nanostructured lipid carriers (NLC) in view of an application for the treatment of onychomycosis and other persistent fungal infections. The development and optimization of the Ucuùba fat based NLC were performed using a Box-Behnken design of experiment. The independent variables were surfactant concentration (% w/v), liquid lipids concentration (% w/v), solid lipids concentration (% w/v), while the outputs of interest were particle size, polydispersity index (PDI) and drug encapsulation efficiency (EE). The Ucuùba fat based NLC were produced and the process optimized determining a predictive mathematical model. Applying the model, two formulations with the pre-required particle size, i.e., 30 and 85 nm, were produced for further evaluation. The optimized formulations were characterized and showed a particle size in agreement to the predicted value, i.e. 33.6 nm and 74.6 nm, respectively. The optimized formulations were also characterized using multiple techniques in order to investigate the solid state of drug and excipients (DSC and XRD), particle morphology (TEM) and interactions between the formulation components (FTIR). Furthermore, particle size and surface charge of the formulations was studied during a one-month stability study and did not evidence any significative modification during storage.

Several methods can be used to evaluate antibody avidity, one of which is the modified ELISA, in which a chaotropic agent is added to disrupt the binding between the antigen and the antibody. Although the avidity index provides relevant information about the functionality of antibodies, it does not allow us to characterize which antigens the antibodies are strongly bound to. To this end, we adapted the Immunoblot and Dot-Blot techniques by adding potassium thiocyanate (KSCN) after incubating nitrocellulose membranes with serum from mice immunized with Neisseria meningitidis outer membrane vesicles (OMVs) or serum from mice immunized with recombinant receptor-binding domain (RBD) of SARS-CoV-2, with different adjuvants for each antigen. In terms of results, when standardizing the incubation time of sera with KSCN, we observed that 5 minutes was the ideal time for both assays, however, when using different dilutions of serum from mice immunized with RBD, there was an influence on the strength of antigen-antibody binding. For the N. meningitidis assay, the antibodies maintained high avidity for the antigens present in the OMVs, PorA, NadA, and Opa, especially in the presence of the aluminum hydroxide adjuvant. The research showed that standardizing the Immunoblot and Dot-Blot in the same assay optimizes time and resources, allowing qualitative analysis for two different antigens, and resulting in more robust information for immunization studies against these pathogens.

Yellow fever (YF) is a pansystemic disease caused by the yellow fever virus (YFV), the prototype species of the family Flaviviridae and genus Flavivirus, and has a highly complex host-pathogen relationship, in which endothelial dysfunction reflects viral disease tropism. In this study, the in situ endothelial response was evaluated. Liver tissue samples were collected from 21 YFV-positive patients who died due to the disease and five flavivirus-negative controls who died of other causes and whose hepatic parenchyma architecture was preserved. Immunohistochemical analysis of tissues in the hepatic parenchyma of YF cases showed significantly higher expression of E-selectin, P-selectin, intercellular adhesion molecule-1, vascular cell adhesion molecule-1, and very late antigen-4 in YFV-positive cases than in flavivirus-negative controls. These results indicate that endothelium activation aggravates the inflammatory response by inducing the expression of adhesion molecules that contribute to the rolling, recruitment, migration, and construction of the inflammatory process in the hepatic parenchyma in fatal YF cases.

The whitefly leads extensive damage to plants through direct feeding, honeydew secretion, plant physiological disorders, and vectoring plant viruses. This study aimed to evaluate the physiological characteristics of susceptible and resistant soybean cultivars to B. tabaci. The experiments were conducted in a greenhouse. Eleven soybean cultivars were selected and infested with 100 adults of B. tabaci at the V3 stage. The evaluation of photosynthetic parameters, such as photosynthetic rate, leaf transpiration, stomatal conductance, and internal CO2 concentration, revealed that B. tabaci infestation influenced gas exchange in soybean plants. The photosynthetic rate was higher in cultivars AS3810 and M8349 during the V6 stage. Infestations led to alterations in photosynthetic parameters, suggesting increased energy demand to maintain photosynthetic activity. However, the response to infestation varied among different cultivars, indicating varying levels of resistance and tolerance to the whitefly's damage. Additionally, the impact of infestation was more significant during the vegetative phenological. In conclusion, B. tabaci infestation affects soybean plants' physiology, leading to changes in gas exchange parameters and water use efficiency. The response to infestation varied among soybean cultivars, suggesting potential differences in resistance to the pest. The study highlights the importance of evaluating the physiological impact of whitefly infestations on soybean.

The plants Agave sisalana (sisal) and Punica granatum (pomegranate) are rich in saponins, which are secondary metabolites known for their therapeutic properties, including anti-inflammatory effects. Although, Brazil is the world's leading sisal producer, approximately 95% of the leaves are discarded after fiber extraction. Similarly, pomegranate peel waste is abundant in Brazil. To address the need for safe and effective anti-inflammatory treatments. This study aimed to create a topical mucoadhesive gel containing a combination of sisal (RS) and pomegranate residue ex-tracts (PR). In vitro experiments examined isolated and combined extracts, as well as the result-ing formulation, focusing on: 1) phytochemical analysis (total saponin content); 2) cytotoxicity (MTT assay); and 3) pharmacological assessment of anti-inflammatory activity (phagocytosis, macrophage spreading, and membrane stability).Results revealed saponin concentrations in grams per 100 grams of dry extract as follows: SR - 29.91 ± 0.33, PR - 15.83 ± 0.93, Association (A) - 22.99 ± 0.01, Gel Base (G1) - 0.00 ± 0.00, and Association Gel (G2) - 0.52 ± 0.05. In MTT tests for isolated extracts, cytotoxicity values (µg/mL) were 3757.00 for SR and 2064.91 for PR. Converse-ly, A and G2 exhibited no cytotoxicity, with increased cell viability over time. All three anti-inflammatory tests confirmed the presence of this activity in SR, PR, and A. Notably, G2 demon-strated an anti-inflammatory effect comparable to dexamethasone.In conclusion, the gel contain-ing SR and PR holds promise as a novel herbal anti-inflammatory treatment. Its development could yield economic, social, and environmental benefits by utilizing discarded materials in Brazil.

Species belonging to the Bauhinia genus, usually known as "pata-de-vaca", are popularly used to treat diabetes. Among them is Bauhinia ungulata var. obtusifolia (Ducke) Vaz, whose leaves are used, as a tea, for medicinal purposes in the Amazon region. The microencapsulation of the aqueous extract of its leaves, containing phenolic compounds, using five different wall materials (maltodextrin: DE11-14, and DE4-7; β-cyclodextrin; pectin, and sodium carboxymethylcellulose) is described in this paper. The microstructure, particle size, thermal behavior, yield, and encapsulation efficiency were investigated and compared using different techniques. Using high-performance liquid chromatography, phenolics, and flavonoids were detected and quantified in the microparticles. Microparticles, obtained with yield and phenolics encapsulation efficiency ranging between 60-83 % and 35-57 %, respectively, showed a particle size distribution between 1.15 and 5.54 µm, spherical morphology, and wrinkled surface. Among them, those prepared with sodium carboxymethylcellulose and pectin proved to be thermally the most stable. They had the highest flavonoid content (23.07 and 21.73 mgRUTE/g Extract) and total antioxidant activity by both the DPPH· (376.55 and 367.86 µmolTrolox/g Extract) and ABTS·+ (1085.72 and 1062.32 µmolTrolox/ g Extract) assays. The chromatographic analyses allowed for quantification, in the microparticles, chlorogenic acid (1.67-1.98 mg/g Extract), p-coumaric acid (0.06-0.08 mg/g Extract), rutin (11.1-12.9 mg/g Extract) and isoquercitrin (0.47-0.53 mg/g Extract), compounds considered responsible for the antidiabetic property attributed to the species.

Although the vegetation of the Cerrado biome is prone to fire, plant species composition can be altered according to its severity and frequency. Furthermore, many Cerrado plant species are resistant and can adapt to frequent fires. Little is known about how plant species of Cerrado environments respond to fire and the extent to which fire is beneficial for their conservation. The present study analyzed the responses of plant species of areas of campo sujo to fire and changes in floristics and vegetation structure at different post-fire intervals. Areas with frequent fires had a greater diversity of species, while the area with 10 years without burning had lower diversity and greater DBH. The distribution of species differed among the four the studied areas. We conclude that fire was beneficial for species diversity in the studied areas of Cerrado since it was able to promote the insertion and removal of species during intervals between fires.

The use of nanomaterials has been increasing in recent times, and they are widely used in industries such as cosmetics, drug, food, water treatment and agriculture. The rapid development of new nanomaterials demands a set of approaches to evaluate the potential toxicity and risks related to them. In this regard, nanosafety has been using and adapting already existing methods (toxicological approach), but the unique characteristics of nanomaterials demand new approaches (nanotoxicology) to fully understand the potential toxicity, immunotoxicity and (epi)genotoxicity. Also, new technologies, such as organ-on-chip and sophisticated sensors, are under development and/or adaptation. All the information generated is used to develop new in silico approaches trying to predict the potential effects of newly developed materials. The overall evaluation of how from the production to final disposition chain of nanomaterials is evaluated under Life Cycle Assessment (LCA), which is becoming an important element of nanosafety considering sustainability and environmental impact. In this review we give an overview of all these elements of nanosafety.

This work aimed to characterize a DBD plasma equipment through optical and electrical measurements, seeking to obtain a greater knowledge of the plasma production process and how it behaves through the adopted parameters, such as frequency and voltage applied between electrodes, at a fixed distance of 1.7 mm. In order to measure them, three different characterization techniques were applied. The first method was the Lissajous figures, a technique quite effective for a complete electrical characterization of DBD equipment. The second technique used was the Optical Emission Spectroscopy, a tool used for the diagnosis of plasma, being it possible to identify the excited species produced in filamentary and diffuse discharge in the plasma. And finally, the triple Langmuir probe technique was used to obtain the electron temperature and electron density. Based on this study, it was possible to identify the equipment efficiency in different regimes. The electron temperature measurement for both systems analyzed were 27.96 eV and 20.69 eV to the filamentary and diffuse regimes, respectively. The density of electrons number to these regimes were 1.09 × 10²¹ m⁻³ and 1.56 × 10²¹ m⁻³.

This work aims to investigate the effect of catalyst content and reaction time by catalytic upgrading from pyrolysis vapors of residual fat at 450 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, refractive index, and acid value) and chemical composition of organic liquid products (OLP), over a catalyst fixed bed reactor, in semi pilot scale. Pellets of Red Mud chemically activated with 1.0 M HCl were used as catalysts. The experiments were carried out at 450 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) Red Mud pellets activated with 1.0 M HCl, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 40, 50, 60, 70 and 80 min in order to analyze the process kinetics. The physicochemical properties (density, kinematic viscosity, acid value, and refractive index) of OLP were determined by official methods. The chemical functions present in OLP determined by FT-IR and the chemical composition by GC-MS. The thermal catalytic cracking of residual fat show OLP yields from 54.4 to 84.88 (wt.%), aqueous phase yields between 2.21 and 2.80 (wt.%), solid phase yields (coke) between 1.30 and 8.60 (wt.%), and gas yields from 11.61 to 34.22 (wt.%). The yields of OLP increases with increasing catalyst content while those of aqueous, gaseous and solid phase decreases. For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of OLP decreases with increasing reaction time. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the thermal and thermal catalytic cracking experiments, the hydrocarbon content within OLP increases with reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties (density, kinematic viscosity, and acid value) and the maximum hydrocarbon content of OLP were obtained at 450 °C and 1.0 atmosphere, using a catalyst fixed bed reactor, with 5.0% (wt.) Red Mud pellets activated with 1.0 M HCl as catalyst.

This work aims to investigate the influence of reaction time and catalyst-to-residual fat ratio by catalytic upgrading from pyrolysis vapors of residual fat at 400 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, and acid value) and chemical composition of bio-oils, over a catalyst fixed bed reactor of activated carbon pellets impregnated with 10.0 M NaOH, in semi pilot scale. The experiments were carried out at 400 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 50, 60, 70, 80, 90, 100 and 120 minutes in order to investigate the process kinetics. The physicochemical properties (density, kinematic viscosity, and acid value) of bio-oils were determined by official methods. The chemical composition of bio-oils determined by GC-MS. The thermal catalytic cracking of residual fat show bio-oils yields from 55.55 to 30.22 (wt.%), aqueous phase yields between 2.83 and 3.19 (wt.%), solid phase yields between 13.56 and 9.75 (wt.%), and gas yields from 27.89 to 55.60 (wt.%). The yields of bio-oil decreases from 74.41 to 30.22% (wt.) with increasing catalyst-to-Tallow kernel oil ratio, while that of gaseous phase increases from 12.87 to 55.60% (wt.). For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of bio-oils decreases as the reaction time increases varying from 0.9266 to 0.8220 g/cm³, 8.10 to 2.24 mm²/s, and 144.14 to 2.37 mg KOH/g. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, ring-containing alkanes, ring-containing alkenes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the pyrolysis and catalytic cracking experiments, the hydrocarbon selectivity in bio-oil increases with increasing reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties density, kinematic viscosity, and acid value were 0.8220 g/cm³, 3.03 mm2/s, and 2.37 mg KOH/g, respectively, with a maximum hydrocarbon concentration of 97.194% (area.) and 2.806% ketones (area.) were obtained at 400 °C and 1.0 atmosphere, 80 minutes, without catalyst. For the catalytic cracking experiments, the maximum hydrocarbon content of 75.763% (area.) and 17.041% (area.) carboxylic acids, 4.702% (area.) ketones (area.), and 2.494% (area.) non-identified oxygenates was obtained at 400 °C and 1.0 atmosphere, 90 minutes, using a catalyst fixed bed reactor, with 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH as catalyst.

Cork oak mortality has reached alarming proportions in the last decades, exacerbated by climate change. Understanding this phenomenon is crucial in finding mitigation or adaptation strategies. This study conducts a diachronic analysis of cork oak mortality over 10 years using GIS tools, focusing on Portugal's Tagus Lezíria region. Topographic, edaphic and climatic variables were employed to create maps of edaphoclimatic aptitude for cork oaks. Dead trees were identified using remote sensing techniques and crown coverage was determined to calculate the mortality index. The diachronic analysis aimed to explore climate change effects on cork oak mortality. A decrease in precipitation was observed, significantly impacting stands with canopy cover below 40%. Furthermore, a negative effect of solar radiation identified only in stands with canopy cover of 40% suggested its role in cork oak decline. This study introduces a novel perspective, highlighting the protective effect of denser canopy cover (above 40%) against excessive solar radiation and the impact of reduced precipitation. The integrated and diachronic approach provides valuable information for adapting management strategies to climate change challenges.

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.

At the beginning of 2023 the Italian former prime minister, the former health minister and 17 others including the current president of Lombardy region, were placed under investigation on suspicion of aggravated culpable epidemic in connection with the government’s response at the start of the COVID-19 pandemic. The charges revolve around the failure by authorities to take adequate measures to prevent the spread of the virus in the Bergamo area, which experienced a significant excess of deaths during the initial outbreak. The aim of this paper is to analyse pandemic data of Italy and Lombardy region in the first 10 days of the pandemic, spanning from the 24th of February 2020 to the 4th of March 2020. The objective is to determine whether the use early warning indicators could have facilitated the identification of a critical increase in infections. This identification, in turn, would have enabled the timely formulation of strategies for pandemic containment, thereby reducing the number of deaths. In conclusion, to translate our findings into practical guidelines, we propose a low-cost early warning method for infectious respiratory diseases with asymptomatic carriers.

Infrared thermography is a contactless imaging technique, useful to measure surface temperature at distance which has been widely applied in animal production. The possible applications within the pig husbandry include sow heat detection, reduction of the incidence of neonatal mortality, recognition of febrile state caused by pathogens, study of metabolic efficiency, evaluation of stress caused by heat, by constraints, or by aggressive interaction and meat quality prediction. Even if this technique could be easily influenced by environmental factors, the continuous improvement in the procedures and the decrease in the cost of the equipment will allow in the next future new and more applications in swine farming.

Bent trees have been observed during the early years in juvenile plantations (less than 5 years-old) of Tectona grandis in Costa Rica. The relationship between bending and the morphological characteristics of the trees was explored. An evaluation of bent trees was conducted in six juvenile plantations (8, 17, 27, 28, 31, and 54 months old) of Tectona grandis. Site 1 with 8-month-old plantations did not display any relationship with any tree morphological variable (diameter, height, and crown weight of tree), whereas for the sites 2, 3, and 4 with 17-, 27-, and 28-month-old plantations, respectively, all the tree morphological variables were statistically correlated with the bent trees. A multiple regression analysis showed that the most influential variables were height to crown base, crown weight, diameter, and total height of the tree. An evaluation of the bending risk factor (RF) was correlated with the height to crown base, crown weight, and form factor. The modulus of elasticity and chemical compositions of bent trees differed from those of straight trees. The causes of tree bending are complex, involving, among other factors, the morphology of the trees, plantation conditions, and other factors specific to the xylem, such as the specific gravity, modulus of elasticity, and presence of calcium and magnesium in the wood.

This paper proposes a model to evaluate business projects to get into an incubator, allowing to rank them in order of selection priority. The model combines the Momentum method to build prospective scenarios and the Multiple Criteria Decision Making (MCDM) method TOPSIS-2N to rank the alternatives. Six business projects were evaluated to be incubated. The Momentum method made it possible for us to create an initial core of criteria for the evaluation of incubation projects. The TOPSIS-2N method supported the decision to choose the company to be incubated by ranking the alternatives in order of relevance. Our evaluation model has improved the existing models used by incubators. This model can be used and / or adapted by any incubator to evaluate the business projects to be incubated. The set of criteria for the evaluation of incubation projects is original and the use of prospective scenarios with a MCDM method to evaluate companies to be incubated does not exist in the literature.

The present work was aimed at the chemical characterization and antimicrobial activity of some extracts of aerial parts (essential oils from leaves and inflorescences, and resins from inflorescences) of two legal hemp (Cannabis sativa) varieties, Tisza and Kompolti, grown in Sardinia. Chemical characterization was carried out by gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS) techniques. The antimicrobial activity of these extracts against a panel of microorganisms was also determined via minimum inhibitory concentration (M.I.C.) determination. While the results showed a minor or negligible antimicrobial activity of the extracts against Gram+ and Candida strains, a good antibacterial activity (especially of resins) was recorded against S. aureus; no substantial differences were detected between of the chemical compositions of the two Cannabis varieties.

Non-ulcerated cutaneous leishmaniasis (NUCL) is an atypical and peculiar clinical form of the disease that was first described by Ponce et al. (1988) in Honduras (Central America), where iso-lated or disseminated popular and/or nodular skin lesions are commonly seen in adolescents and young adults. Leishmania (L.) chagasi was then incriminated as the causal agent of the disease, as well as of American visceral leishmaniasis (AVL), although NUCL has been shown to be more prevalent than AVL in the region. Considering, however, the dubious taxonomic character of the causal agent of NUCL, as there is no evidence of this form of disease associated with L. (L.) cha-gasi in South America, this study aimed to carry out a retrospective taxonomic analysis on a se-ries of studies on the diagnostic approach to the Honduran parasite in loco (El Tigre island, Amapala municipality, west coast of Honduras), where taxonomic characters of a biological (in vitro and in vivo), epidemiological (vector and canine reservoir), clinical-immunological (im-munopathological features of in situ skin lesion and systemic infection) and molecular (ge-nomic/phylogenetic analyses) nature were considered. The findings, particularly those of mo-lecular nature, such as: the Honduran parasite showed to be more ancestral (molecular clock analysis of the DNA polymerase alpha subunit gene) than all viscerotropic ones [L. (L.) chagasi, L. (L.) donovani and L. (L.) infantum], as well as presenting an absolutely unprecedented structural variation on chromosome 17 and the highest frequency of genomic SNPs (more than twice the number seen in the Brazilian parasite), in addition to representing a different phylogenetic lin-eage (mainly in the NJ - RNA Pol II tree) from those viscerotropic ones, have pointed to the characterization of a new leishmanine parasite, Leishmania (Leishmania) poncei n. sp. (Kinetoplas-tea: Trypanosomatidae), in honor of Professor Ponce, who was the first researcher to describe NUCL in Honduras.

The risk of the emergence and reemergence of zoonoses is high in regions that are under anthropogenic actions, as they contribute to the risk of vector disease transmission. Yellow fever (YF) is among the main pathogenic arboviral disease in the world, and the Culicidae Aedes albopictus has been proposed to have the potential to transmit yellow fever virus (YFV). This mosquito inhabits both urban and wild environments, and under experimental conditions, it has been shown to be susceptible to infection by YFV. In this study, the vector competence of the mosquito Ae. albopictus for the YFV was investigated. Female Ae. albopictus were exposed to non-human primates (NHP) of the genus Callithrix infected with YFV for blood meal. Subsequently, on the 14th and 21st days post infection, the legs, heads, thorax/abdomen and saliva of the arthropods were collected and analyzed by viral isolation and molecular analysis techniques to verify the infection, dissemination and transmission. The presence of YFV was detected in saliva samples through viral isolation and in the head, thorax/abdomen and legs both by viral isolation and by molecular detection. The susceptibility of Ae. Albopictus to YFV confers a potential risk of reemergence of urban YF in Brazil.

Increasingly, there is a focus on utilising renewable energy resources in a bid to fulfil increasing energy requirements and mitigate the climate change impacts of fossil fuels. While most renewable resources are free, the technology used to usefully convert such resources is not and there is an increasing focus on improving the conversion economy and efficiency. To this end, advanced control technologies can have a significant impact and is already a relatively mature technology for wind turbines. Though hydroelectric plants can use simple regulation systems, significant benefits have been shown to accrue from the appropriate use of the same control methods designed for wind turbine plants. This represents the key point of the paper. In fact, to date, the application communities connected with wind and hydraulic energies have had little communication, resulting in little cross fertilisation of control ideas and experience, particularly from the more mature wind area to hydrodynamic systems. Therefore, this paper examines the models and the application of control technology across both domains, both from a comparative and contrasting point of view, with the aim of identifying commonalities in models and control objectives, as well as potential solutions. Key comparative reference points include the articulation of the exployed models, specification of control objectives, development of high--fidelity simulators, and development of solution concepts. Not least, in terms of realistic system requirements are the set of physical and constraints under which such renewable energy systems must operate, and the need to provide reliable and robust control solutions, which respect the often remote and relatively inaccessible location of many onshore and offshore deployments.

This paper investigates the effect of Fe contamination on the microstructure and mechanical properties of Al-7Si-0.7Mg-Fe2.5 alloy processed by Laser Powder Bed Fusion (LPBF) and heat treated in two different conditions: (1) Solution Heat Treatment (SHT) at 520 °C, followed by artificial ageing at 160 °C (T6), and (2) Direct Artificial Ageing of the as-printed material at 160 °C (DAA). Microstructural characterization was carried out by Optical Microscopy (OM), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), and Transmission Electron Microscope (TEM). Mechanical characterization was carried out by tensile tests at room temperature. The formation of fine AlSiFe phases such as α-AlFeSi, β-AlFeSi, and π-Al8Si6Mg3Fe had no deleterious effect on the mechanical properties compared to previous studies for AlSIMg alloys without Fe. However, compared to the as-printed condition, the T6 heat treatment decreased the ultimate tensile strain significantly, while the elongation to the fracture presented a slight improvement.

Background: Evidences on the effects of chemotherapy treatment cycles on measures of muscle, mental state, social and cognitive performance are scarce. Objective: To analyze the effects of chemotherapy cycles on muscle strength and activation, functional capacity, quality of life, fatigue and anxiety of women with breast cancer. Methods: Twenty-two women divided into a treatment group (n = 10; 46.6 ± 9.6 years) and control group (n = 12; 51.6 ± 7.0 years) participated in the study. Analysis of muscle performance, quality of life, fatigue and anxiety after the 2nd and 4th cycle of chemotherapy with anthracyclines and cyclophosphamide were performed in women with breast cancer (TRA) and compared to healthy women (CTR). Two-way ANOVA was used to compare the variance of the means and the significance level was set as p≤0.05. Results: Differences were found in the muscular activation of the vastus medialis between the groups at post time (p = 0.038), as well as in the sit and stand test in the baseline (p<0.001) and post moment (p<0.001). Functional capacity performance was different between baseline (p<0.001) and post-time (p<0.001) groups. Additionally, the TRA group worsened the quality of life in the domains of functional capacity (p<0.001) and limitation of physical aspects (p=0.002), besides presenting negative changes in fatigue. Conclusion: Anthracycline and cyclophosphamide chemotherapy cycles reduce muscular performance and affect biopsychosocial variables in women with breast cancer.

Large power transformers are generally associated with a maximum capacity rating of 100 MVA or higher. These large liquid dielectric power transformers are a custom-built piece of equipment, thus very expensive, and a backbone element of the power grid. In extreme cases as, for example, severe geomagnetic disturbances, permanently monitoring their condition will enhance their electrical reliability and resilience to guarantee efficient management of its life cycle. However, some traditional monitoring/diagnosis techniques have singular features when applied to large power transformers and their interlinked subsystems. In this context, and since that information is hardly put in evidence and compiled in the literature, this paper reviews the particularities of monitoring and diagnosing those assets.

The aim of this review is to present the Quality by Design (QbD) model as a suitable methodology to perform research in the academic Costa Rican institutions that teach Pharmacy. Pubmed, Science Direct, and Google Scholar databases were screened for original and review papers, as well as short communications published not more than 10 years ago. Publications were screened by title and abstract. Relevant references were used to develop three important themes: The University’s Research Model in Costa Rica, QbD Model, and QbD as a Research Methodology for Industrial Pharmacy in the Academy. In this sense, the QbD model is a great methodology for carrying out research projects regarding Pharmaceutical Sciences but especially for Drug Development. Academic research based on this model enables training and developing practical, scientific, and leadership skills in pharmacy students. The generated knowledge can be shared in the classrooms, which represents an ideal environment to communicate their research results and to foster collaborative work between researchers, professors, and students. The participation of all these actors allows a high level of commitment to research work, which benefits the scientific advancement of the university and society. It is important to visualize the student body as potential key actors in the research process, encouraging in them the desire to become trained scientific researchers who want to pursue a career in the academy, giving continuity to it.

SARS-CoV-2 infection triggers distinct patterns of disease development, characterized by significant alterations in host regulatory responses. Severe cases exhibit profound lung inflammation and systemic repercussions. Remarkably, critically ill patients display a "lipid storm", influencing the inflammatory process and tissue damage. Sphingolipids (SL) play pivotal roles in various cellular and tissue processes, including inflammation, metabolic disorders, and cancer. In this study, we employed high-resolution mass spectrometry to investigate SL metabolism in plasma samples obtained from control subjects (n=55), COVID-19 patients (n=204), and convalescent individuals (n=77). These data were correlated with inflammatory parameters associated with the clinical severity of COVID-19. Additionally, we utilized RNAseq analysis to examine the gene expression of enzymes involved in the SL pathway. Our analysis revealed the presence of thirty-eight SL species from seven families in the plasma of study participants. The most profound alterations in the SL species profile were observed in patients with severe disease. Notably, the predominant sphingomyelin (SM d18:1) species emerged as a potential biomarker for COVID-19 severity, showing decreased levels in the plasma of convalescent individuals. Elevated SM levels were positively correlated with age, hospitalization duration, clinical score, neutrophil count, as well as the production of IL-6 and IL-8. Intriguingly, we identified a putative protective effect against disease severity mediated by SM (d18:1/24:0), while ceramide (Cer) d18:1/24:1 and d18:1/24:0 was associated with increased risk. Moreover, we observed enhanced expression of key enzymes involved in SL pathway, in blood cells from severe COVID-19 patients, suggesting a primary flow towards Cer generation in tandem with SM synthesis. These findings underscore the potential of SM as a prognostic biomarker for COVID-19 and highlight promising pharmacological targets. By targeting sphingolipid pathways, novel therapeutic strategies may emerge to mitigate the severity of COVID-19 and improve patient outcomes.

This study develops a structure for mapping native vegetation in a transition area between Brazilian Cerrado and Atlantic Forest from integrated spatial information from the Sentinel-1 and Sentinel-2 satellites. Most studies use this data separately, however, the integrated use of optical sensors with Synthetic Aperture Radar (SAR) sensors can improve the methodology for classifying land use and land cover (LULC). The fusion of Sentinel-1 and Sentinel-2, for example, can increase the accuracy of mapping algorithms, using complementary information, such as spectral, backscattering, polarimetry, and interferometry. The study area comprises the Lobo Reservoir Hydrographic Basin, which is part of an environmental conservation unit protected by Brazilian law and with significant human development. LULC were classified, using the random forest deep learning algorithm. The classifying attributes were backscatter coefficients, polarimetric decomposition, and interferometric coherence for radar data (Sentinel-1), and optical spectral data, comprising bands in the red edge, near infrared, and shortwave infrared (Sentinel-2). The attributes were evaluated in three settings in which the SAR and optical data were evaluated separately (C1 and C2, respectively) and in an integrated manner (C3). The study found greater accuracy for C3 (96.54%), an improvement of nearly 2% compared to C2 (94.78%) and more than 40% in relation to C1 (55.73%). The classification algorithm encountered significant challenges in identifying wetlandsin C1, but performance improved in C3, enhancing differentiation by stratifying a greater number of classes during training and facilitating visual interpretation during sampling. Accordingly, the use of SAR and optical data becomes an alternative to optimize LULC mapping in tropical regions, due to the limited influence of atmosphere on images in the microwave range.

Advanced genomics, transcriptomics and epigenomics techniques are providing unprecedented insights into the understanding of the molecular underpinnings of the central nervous system, including the neuro-sensory cochlea of the inner ear. Here, we report for the first time a comprehensive and updated overview of the most advanced omics techniques for the study of nucleic acids, and their applications in cochlear research. We describe the available in vitro and in vivo models for hearing research, the principles of genomics, transcriptomics and epigenomics, alongside their most advanced technologies (like single cell omics and spatial omics), which allows to investigate the molecular events that occur at single cell resolution retaining the spatial information.

Human T-lymphotropic virus type 1 (HTLV-1) is associated with neurological, degenerative, and inflammatory diseases. Brazil has regions with high prevalence rates. The prevalence among relatives of positive people is high, and intrafamily transmission causes the conservation of the infection for different generations. The investigation of epidemiological and molecular factors may clarify the factors associated with the efficacy of intrafamilial transmission of HTLV-1. Objective: To analyze the epidemiological and molecular factors associated with intrafamilial transmission of HTLV-1 in an endemic area of Brazil. Material and Methods: A cross-sectional study investigated 72 relatives from 14 families with more than one infected. Epidemiological data were collected from all family members, and genetic sequencing was performed, phylogenetic analysis of 22 positive relatives. Results: The prevalence of HTLV-1 in families with infected people was 56.94% (41/72). Twelve vertical transmission routes and ten horizontal transmission routes were identified. Phylogenetic analysis demonstrated the absence of polymorphisms between infected mother and child sequences, while sequences of couples presented nucleotide divergence of up to 3%.among themselves. It was also identified in a family with an intrafamilial transmission with the occurrence of two viral strains. Conclusion: Molecular data confirmed intrafamilial transmission. They also indicated little genetic variability between the sequenced samples of family members and those deposited in GenBank used in this study. The absence of polymorphisms was observed in cases of vertical transmission, indicating a tendency to perpetuate identical sequences regardless of the time of acquisition of the infection.

The World Health Organization has estimated an annual occurrence of approximately 392 million Dengue virus (DENV) infections in more than 100 countries where the virus is endemic, and this represents a serious threat to humanity. DENV is a serologic group with four distinct serotypes (DENV-1, DENV-2, DENV-3, and DENV-4) belonging to the genus Flavivirus, in the family Flaviviridae. Dengue is the most widespread mosquito-borne disease in the world. The ~10.7 kb DENV genome encodes three structural proteins (capsid [C], pre-membrane [prM], and envelope [E]) and seven non-structural (NS) proteins (NS1, NS2A, NS2B, NS3, NS4A, NS4B, and NS5). The NS1 protein is a membrane-associated dimer and a secreted, lipid-associated hexamer. Dimeric NS1 is found on membranes both in cellular compartments and cell surfaces. Secreted NS1 (sNS1) is often present in patient serum at very high levels, which correlates with severe dengue symptoms. This study was conducted to discover how NS1 protein, microRNAs-15/16 (miRNAs-15/16), and apoptosis are related during DENV-4 infection in human liver cell lines. Huh 7.5 and HepG2 cells were infected with DENV-4, and miRNAs-15/16, viral load, NS1 protein, and caspases-3/7 were quantified after different times of infection. This study demonstrated that miRNAs-15/16 are overexpressed during infection of HepG2 and Huh 7.5 cells by DENV-4 and have a relationship with NS1 protein expression, viral load, and activity of caspases-3/7, thus making these miRNAs potential injury markers during DENV infection in human hepatocytes.

Globalization has had an impact on the education system in the UAE, where increased use of bilingual curriculum (Arabic-English) is held in high regard. Nevertheless, literacy among Emirati children and teenagers remains low. This study uses a 15-item, open-ended questionnaire completed by Emirati parents and an 8-item, open-ended questionnaire completed by Emirati primary school children from 8 to 11 years of age, and compares the translation of The Little prince into Modern Standard Arabic (MSA) and into the Emirati dialect. The results suggest that not only the Emirati dialect, but any Arabic dialect (in its respective Arab country) could be used in primary schools to motivate children to read in Arabic and bridge the gap between their spoken language (dialect) and formal written Arabic. Not only must an Arab child learn how to read, but also, they have to understand a very formal language system that they are not used to speaking at home, i.e., Modern Standard Arabic (MSA). Having books in their own dialects may make children more interested in reading, as they can understand them more easily.

Objective: To identify risk factors(RF) related to abnormal glucose regulation(AGR) 3 years postpartum according to 3-month-postpartum glucose status. Research design: Normoglycemic pregnant women of the St. Carlos Gestational Study included before gestational week 12, during 2015-2017. Of 3,036 eligible women, 2529 were followed-up until delivery: 1400 participated in postpartum follow-up. AGR defined as fasting serum glucose (FSG)>5.6 mmol/L and/or HbA1c >5.7% (39 mmol/mol) and/or 2h-SG ≥140/mg/dL after 75-g OGTT. 12-modifiable and 3-unmodifiable RF were analyzed for associations with glycemic changes. Reinforcement of Mediterranean Diet adherence was provided to all women at the postpartum visit by a dietitian Results: 137/1400(9.8%) women presented AGR 3 years postpartum, 27/137(19.7%) also had at 3 months, whereas 110/137(80.2%) had not. The remaining 1,263(90.2%) women were normoglycemic 3 years postpartum, 1180/1263(84.3%) were at 3 months, while 83/1263(6.08%) had AGR and became normoglycemic. Women with GDM were more likely to progress to AGR 3 years postpartum (OR:1.60[1.33-1.92]) and less likely to remain normoglycemic (OR:0.22[0.15-0.33]) versus non-GDM women. Having >2/3 unmodifiable RF was associated with a reduced rate of maintained normoglycemia (OR:0.56[0.39-0.80]) and an increased risk of progression to AGR (OR:1.90[1.28-2.83]). Having >5/12 modifiable RF was associated with a reduced rate of maintained normoglycemic (OR:0.74[0.51-0.99]) and reversion of AGR (OR:0.49[0.25-0.97]), an increased progression to AGR (OR:1.40[1.00-2.09]), and persistence of AGR (OR:2.57[1.05-6.31]). Pre-gestational BMI≥25kg/m2 (OR:1.80[1.19-2.71]), post-delivery weight gain (OR:2.22[1.10-4.48]), and waist circumference >89.5cm (OR:0.54[0.36-0.79]), (all p<0.05) were the main modifiable RF. Conclusions: RF related to an increased probability for 3-year-postpartum AGR despite 3-month normoglycemia were identified, potentially useful when designing personalized strategies for pregnant women, directed towards minimizing unfavorable outcomes.

Civil construction is one of the oldest known activities in humanity, reports indicate that builders of the Roman Empire already sought the reuse of materials. Currently, considering the depletion of the supply of natural resources, the recycling of solid waste from construction and demolition (CDW), not only provides new products, but also offers ecological and economic alternative. In this context, this research seeks new variables for the disposal of waste from construction and demolition having in the composition of artificial finishing stones an odd possibility to be analyzed. In this research was developed and analyzed a new composite from the construction and demolition waste using as a binder an orthophthalic polyester resin. The residue was sieved and separated by granulometry by the simplex centroid method, the best compacted mixture was determined statically by ANOVA and the Tukey test. The residue was characterized by X-ray fluorescence and the resin by infrared spectroscopy by Fourier transform. Artificial rock plates were produced with 85% residue and 15% resin, by mass, by vibro system, compression and vacuum, later were cut for mechanical, physical and chemical tests. Analysis was performed by scanning electron microscopy of fractured compositions as well as grain sizes. The artificial stone with the best results presented density of 2,256 g/cm3, water absorption of 0.69%, apparent porosity of 1.55%; bending strength of 34.74 MPa and compression of 111.96 MPa; good results in the alterability and thermal tests. In this satisfactory scenario, the use of this waste in the composition of artificial rocks is promising because it directly meets the concept of sustainable development; replacing the concept of end-of-life of the linear economy, by new circular flows of reuse, restoration and renovation, in an integrated process the circular economy; as well as the quality of the final product with properties similar to the artificial rocks already marketed.

This paper presents a brief account and rationale for implementation of competency-based learning in any form of management and leadership development programmes in South Africa. The fact that competency-based learning (CBL), also known as outcomes-based learning has been scrapped from the schooling system in South Africa is unfortunate as this method enhances critical thinking skills and practical problem-solving skills. This paper presents CBL as a model of meta-cognitive approach to learning that integrates both theory and practice into experiential learning through six dimensions, namely, active learning, constructive learning, cumulative learning, goal-oriented learning, learner-centred and curriculum design strategies. In the advent of the fast-paced global economy, managers and leaders need to seek those business schools that value real-time practical approach to curriculum for relevance and to maximize shareholder value through human resource development. This brief presentation ends by recommending an approach through CBL that fosters three critical pillars of leadership development, namely: intellectual, behavioural and emotional agenda.

Kaolin protective effect was assessed in a white grapevine cultivar ‘Cerceal’ in ‘Alentejo’ Region (southeast Portugal) where plants face extreme conditions during summer season. We addressed the hypothesis that kaolin effects lead to several changes in leaves, fruits and wine characteristics on the primary and secondary metabolism. Results showed that kaolin reduces leaf temperature which provoke an improvement in physiological parameters such as net photosynthesis and water use efficiency. This protection interferes with berries colour, leaving them more yellowish, and an increase in phenolic compounds were observed in all fruit tissues (skin, seed and pulp). Also, both berry and wine characteristics were strongly affected, with an increase of tartaric and malic acid and consequently high total acidity, while the sugar concentration decreased 8.9% in berries provoking a low wine alcohol level. Results also showed that kaolin induces high potassium, magnesium and iron, and low copper and aluminum concentrations. Moreover, the control wine showed higher content of esters related with hostile notes whereas wine from kaolin treated vines presented higher content of esters associated with fruity notes. Overall, the results strengthen the promising nature of kaolin application as summer stress mitigation strategy protecting grapevine plants and improving fruits quality and more balanced wines.

This study employed e-Vol DX cone beam computed tomography (CBCT) software to assess dentin remnants in the furcation area of mesial canals in mandibular molars during root canal retreatment (RCR). Four groups (Reciproc®, ProTaper Next®, Race Evo®, Protaper Gold®) were subjected to RCR, and CBCT images were captured before (T1) and after (T2) treatment. Measurements of remaining dentin thickness at 1 mm and 3 mm below the furcation were scrutinized. Results revealed no significant differences in mean thicknesses of mesiobuccal (MB) and mesiolingual (ML) canals at 1 mm and 3 mm from the furcation pre-treatment (T1). Post-treatment (T2) showed analogous findings, with no significant differences in mean thicknesses. However, disparities surfaced between MB and ML canals at both distances, both before and after retreatment. In essence, the evaluated instruments exhibited safety in RCR, implying their appropriateness for use in critical areas of mandibular molars without inducing excessive wear. This study underscores the instruments' reliability in navigating danger zones during RCR, contributing valuable insights for dental practitioners handling complex root canal scenarios in mandibular molars.

Carbapenemase resistance in Enterobacterales is a global public health problem and rapid and effective methods to detect resistance mechanisms are needed urgently. Our aim was to evaluate the performance of a MALDI-TOF MS based KPC detection protocol from patients’ positive blood cultures, short-term cultures and colonies at health care settings. Bacterial identification and KPC detection were achieved after protein extraction with organic solvents and target spot loading with suitable organic matrices. Confirmation of KPC production was performed by susceptibility tests, blaKPC amplification by PCR and sequencing. KPC direct detection (KPC-peak at approximately 28.681 Da) from patients’ positive blood cultures, short-term cultures and colonies, once bacterial identification was achieved, showed an overall sensibility and specificity of 100% (CI95: [95%,100%] and CI95: [99%, 100%], respectively). Concordance between hospital routine bacterial identification protocol and identification with this new methodology from the same extract used for KPC detection was ≥92%. This study represents the pioneering effort to directly detect KPC using MALD-TOF MS technology, conducted on patient-derived samples obtained at the hospitals for validation purposes, in a multi-resistance global context that requires concrete actions to preserve available therapeutic options and reduce the spread of antibiotic resistance markers.

Antimicrobial resistance (AMR) is a growing public health concern worldwide, and it poses a significant threat to human, animal, and environmental health. The overuse and misuse of antibiotics have contributed significantly to the emergence and spread of antimicrobial resistance, which may lead to significant economic consequences like reduced productivity and increased healthcare costs. Nanotechnology offers a promising platform for addressing this challenge. Nanoparticles have unique properties that make them highly effective in combating bacterial infections by inhibiting the growth and survival of multidrug-resistant bacteria in three areas of health: human, animal, and environmental. To conduct an economic evaluation of surveillance in this context, it is crucial to have a comprehension of the connections to be addressed by several nations by implementing national action policies based on the One Health strategy. This review provides an overview of the progress made thus far and presents potential future directions to optimize the impact of nanobiotics on AMR.

The interest on the use of renewable energy resources is increasing, especially towards wind and hydro powers, which should be efficiently converted into electric energy via suitable technology tools. To this aim, self--tuning control techniques represent viable strategies that can be employed for this purpose, due to the features of these nonlinear dynamic processes working over a wide range of operating conditions, driven by stochastic inputs, excitations and disturbances. Some of the considered methods were already verified on wind turbine systems, and important advantages may thus derive from the appropriate implementation of the same control schemes for hydroelectric plants. This represents the key point of the work, which provides some guidelines on the design and the application of these control strategies to these energy conversion systems. In fact, it seems that investigations related with both wind and hydraulic energies present a reduced number of common aspects, thus leading to little exchange and share of possible common points. This consideration is particularly valid with reference to the more established wind area when compared to hydroelectric systems. In this way, this work recalls the models of wind turbine and hydroelectric system, and investigates the application of different control solutions. The scope is to analyse common points in the control objectives and the achievable results from the application of different solutions. Another important point of this investigation regards the analysis of the exploited benchmark models, their control objectives, and the development of the control solutions. The working conditions of these energy conversion systems will be also taken into account in order to highlight the reliability and robustness characteristics of the developed control strategies, especially interesting for remote and relatively inaccessible location of many installations.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

The coffee industry loses millions of dollars annually worldwide due to the Coffee Berry Borer (CBB); these losses imply a decrease in quality and production. Traps are used to monitor their flight and for pest control. The main objective was to determine the flight pattern and trap capture percentages of the CBB population over time using column traps (CTs) in two independent field experiments. CTs were composed of four traps installed at four different heights 0.5, 1.5, 2.5, and 3.5m above ground. Our results demonstrated a significant difference in CBB capture by traps placed at different heights above the ground. The CT capture maintained a pattern throughout this study's lag; the lower the height, the greater the percentage of CBBs captured. In Experiments A and B, the traps placed at 0.5m caught 67% and 85% of the CBBs captured, respectively. Furthermore, the trap set at 1.5m above the ground in the multi-level CT showed a higher capture percentage than the individually placed trap (also at 1.5m). The pattern of the capture and proportion of the CBB in the CTs were maintained throughout the study despite the season, changes in temperature, and relative air humidity. We suggested that CTs could be explored as a useful tool for capturing the CBB, considering its monitoring and management.

The bonds of England and the UAE date back to over 220 years ago. This article explores the interference of Arabic prepositions in the English used in the United Arab Emirates (UAE), and their occurrences in light of gender and level of education, two important social variables related to linguistic behavior. To do so, participants will translate 20 sentences in Arabic into English as well as fill in 30 gaps in sentences in English with the missing prepositions. We will also experiment how musical intelligence may improve Emiratis’ performance regarding preposition. A study will be carried out to verify if participants from the experimental group, who will receive training on prepositions through music, obtains better results compared to the control group, who will receive training through a more traditional way (by listening to the instructor and repeating).

The aim of this study was to provide information on the levels of toxic (Cd and Pb) and essential (Cu, Fe and Zn) elements in cow’s milk produced in the State of Pernambuco (Brazil). A total of 142 samples of raw milk were collected, and the concentrations of essential and toxic elements were determined by inductively coupled plasma-optical emission spectrometry. In almost 30 % of the samples analyzed, the Pb content exceeded the maximum level established in the Brazilian legislation (0.05 mg/l). By contrast, in all samples the Cd content was below the maximum allowable level (0.02 mg/L). The essential trace elements Cu, Fe and Zn were generally present at lower concentrations than reported in other studies and can be considered within the deficient range for cow’s milk. Statistical and chemometric procedures were used to evaluate the main factors influencing the metal concentrations (proximity to major roads, presence of effluents, and milking method). The study findings demonstrate that the proximity of the farms to major roads influences the concentrations of Cd, Pb and Cu and that this is the main factor explaining the Pb content of milk. In addition, the presence of effluents influenced the concentrations of Cu, while no relationship between the metal content and the milking method was observed. Thus, in accordance with the study findings, consumption of cow’s milk produced in the region can be considered a risk to public health due to the high concentrations of Pb and the low concentrations of other essential minerals such as Cu, Zn and Fe in some of the milk samples.

The purpose is to verify trends of scientific production from 2010 to 2020, considering the best universities of the United States, China, the European Union (EU) and private companies. The top 30 universities in 2020 in China, the EU, and the US and private companies were selected from the SCImago institutions ranking (SIR). The positions in 2020, 2015, 2010 in SIR and three sub-indicators were analyzed by means of non-parametric statistics, taking into consideration the effect of time and group on rankings. American and European Union universities have lost positions to Chinese universities and even more to private companies, which have improved. In 2020, private companies have surpassed all other groups considering Innovation as sub-indicator. The loss of leadership of European and partly American universities mainly concerns research linked to the production of patents. This can lead to future risks of monopoly that may elude public control and cause a possible loss of importance of research not linked to innovation.

Sugarcane plays a crucial role in global sugar and ethanol production. Conventionally, sugar-cane propagation involves planting billets. However, Brazilian researchers have introduced the innovative pre-sprouted seedlings (PSS) method, widely used in the MEIOSI (Simultaneously Occurring Interrotational Method) system. Although MPB has several advantages over the con-ventional method, its sensitivity to water scarcity is a challenge. The study aimed to evaluate the survival and growth of PSS inoculated with Bacillus licheniformis and Bacillus subtilis under differ-ent water regimes. The experiment was conducted in the field in a randomized block in strips (split-block) using a 2×4 factorial scheme consisting of two inoculation conditions (with and without bacteria) and four water regimes (0%, 33%, 66%, and 100% of the ideal irrigation). The bacteria increased the PSS's survival and water use efficiency in the field. In addition, inocula-tion increased root and shoot growth, as well as the nutrient uptake such as N, P, Mn, Zn, and Cu, which resulted in a higher number of stalks per meter and, therefore, a higher multiplica-tion rate in the MEIOSI system. Inoculation proved to be a promising alternative for establishing PSS under water restriction.

The interest on the use of renewable energy resources is increasing, especially towards wind and hydro powers, which should be efficiently converted into electric energy via suitable technology tools. To this aim, data--driven control techniques represent viable strategies that can be employed for this purpose, due to the features of these nonlinear dynamic processes working over a wide range of operating conditions, driven by stochastic inputs, excitations and disturbances. Some of the considered methods, such as fuzzy and adaptive self--tuning controllers, were already verified on wind turbine systems, and similar advantages may thus derive from their appropriate implementation and application to hydroelectric plants. These issues represent the key features of the work, which provides some guidelines on the design and the application of these control strategies to these energy conversion systems. The working conditions of these systems will be also taken into account in order to highlight the reliability and robustness characteristics of the developed control strategies, especially interesting for remote and relatively inaccessible location of many installations.

This paper presents a review on numerical and experimental methods to predict fracture of ad-vanced high strength steels (AHSS). AHSS are widely processed through sheet metal forming processes. Although being an excellent choice when lightweight, high strength and ductility are critical factors, their multi-phase microstructure accentuates forming challenges. To accurately model forming behavior, necking based failure criteria as well as direct fracture models require improvements. As a necking based failure model, the conventional forming limit diagram/curve (FLD/FLC) presents limitations such as in estimating direct fracture (surface cracks, edge cracks, shear cracks), as well as deformation histories under nonlinear strain paths. Thus, significant re-search efforts are being made towards the needs of advanced fracture constitutive models capa-ble of predicting fracture scenarios without necking, more frequently observed in the realm of AHSS. Scientific community research is divided into several directions aiming at improving the forming and fracture behavior accuracy of parts subjected to sheet metal forming operations. In this review paper, a comprehensive overview on ductile fracture modeling is presented. Firstly, the FLD/FLC limitations modeling fracture behavior in sheet metal forming operations are stud-ied. Followed by the recent trends in constitutive material modeling. Afterwards, material char-acterization methods advancements to cover a broad range of stress states are comprised. Final-ly, damage and fracture models predicting failure in AHSS are investigated. This review paper supplies relevant information on the current issues the sheet metal forming community is chal-lenged with due to the trend towards AHSS employment in the automotive industry.

Human keratinocytes and melanoma can stick together to form clusters after eight days in co-culture. As in dynamic system concepts, one can consider cluster formation as the system attractor, cell seeding as the initial condition, and density change over time as a path within the basin of attraction. Herein, Cellular Automata, which is a class of Agent-Based Models, and Boolean Networks are discrete modeling methods used in population dynamics such that running the dynamics of cellular automata backward reveals an underlying network in terms of basin of attraction, also known as global dynamics. Thus, we hypothesize that one can estimate the local dynamic of an agent-based model from the basin of attraction of a boolean network. Here, we propose an approach to estimating these agent-based model rules, which consists of comparing the density states within each state transition and reaching a consensus among state transitions belonging to a basin of attraction of a boolean network. The objectives of this study are: (1) to infer a boolean network from the co-culture growth curve; (2) to estimate the rules of agent-based models; and (3) to implement spatial dynamics simulations. The binarization of the growth curve shows high population density after four days; the estimated agent-based model rules were compatible with cell proliferation and migration in agreement with literature, so we had to propose individual rules for survival and death. Spatial dynamics shows that (1) keratinocytes exhibit a higher density in neighborhoods where melanoma is present; (2) the chance of keratinocyte migration increases until the fourth day, then decreases, and the probability of survival increases substantially after four days; and (3) cells with low proliferation capacity die and free space for those with high ones. Our approach suggests that the attractor state of cell co-culture is induced mainly by an increase in keratinocyte migration and survival. Our approach has the potential to offer valuable clues about microenvironmental interactions or configurations that drive population dynamics.

Background: The aim of this study was to examine cervical multifidus muscle morphology and its impact on postural balance in patients with post-stroke. Methods: This is a pilot study. A convenience sample of 24 volunteers of 67 ±8.5 years (12 with hemiparesis due to post-stroke, 12 healthy) was recruited for this study. The outcomes measured were the thickness of the multifidus muscle using ultrasonography, Modified Functional Reach Test (MFRT), Timed Up and Go (TUG) test and Berg Balance scale (BBS). Results: No significant differences in the ultrasound values between stroke patients' paretic and non-paretic sides were found. Similarly, there were no significant differences between the non-paretic side of stroke patients and the non-paretic side of the control group, (all, p>0.05). Additionally, no significant correlations between the ultrasonographic variables of the multifidus muscles and the main outcome measures were identified. Conclusions: In conclusion, our study did not find significant differences in cervical multifidus muscle morphology between healthy individuals and post-stroke patients in relation to postural balance.

The electronic transport stability in nanodevices composed by metal/trans-polyacetylene /metal with different long length has contributed greatly for performance, homogeneity, stability, organization of the chains, reproducibility and higher conductivity. In this paper, we present an analytical study of the electronic transport characteristics from dimerized trans-polyacetylene (trans-PA) molecules containing an odd-even number of sites coupled to metal leads (left and right) in T-shaped geometry using the extended Su-Schrieffer-Heeger (SSH) model based on tight-binding Hamiltonian with the Non-Equilibrium Green´s Function (NEGF) via Heisenberg´s equation of motion and the Keldysh´s formalism. Due to the complexity of the T-shaped odd-even chain, our proposal was to test the effects on the finite-length network for three, four, five sites and furthermore foresee for 17-sites. We show how to tune dimerization strength () coupling to the parameters and T-shaped geometry of the device to which it affects the overlap integral localized at the three endpoints of the T-shaped system, making both the odd and even chains to undergo a metal-insulator transition in their electronic behavior. The results reached through control parity of the chain plane of the parameters governing () the electronic and experimental tunneling allow a better understanding of the subject.

Solar concentrator photovoltaic collectors are able to deliver energy at higher temperatures for the same irradiances, since they are related to smaller areas for which heat losses occur. However, to ensure the system reliability, adequate collector geometry and appropriate choice of the materials used for all their components will be crucial. The present study focuses on the re-design of the C-PV collector reflector currently produced by the Swedish company Solarus AB, together with a comparative analysis based on the annual assessment of the solar irradiance in the collector. An open-source ray tracing code (Soltrace) is used to accomplish the modelling of optical systems in concentrating solar power applications. Symmetric parabolic reflector configurations are seen to improve the PV system performance when compared to the conventional structures currently used by Solarus. The parabolic geometries, using either symmetrically or asymmetrically placed receivers inside the collector, achieve both the performance and cost-effectiveness objectives: for almost the same area or costs, the new proposals for the PV system may be in some cases 70 % more effective as far as energy output is concerned.

(1) Background: Older people hospitalized with Covid-19 can reduced the capacity to walk. However, the prevalence of impairment of ambulation capacity still need to be established. Objective: To estimate the prevalence and identify the risk factors associated with the impairment of ambulation capacity at hospital discharge of older people with Covid-19. (2) Methods: A retrospective cohort study. Included age &gt; 60 years, both sexes, hospitalized due to Covid-19. Clinical data was collected from the medical records. Ambulation capacity prior to Covid-19 infection was assessed through the patient report from his relatives. Multiple logistic regressions were performed to identify the risk factors associated with the impairment of ambulation at hospital discharge. (3) Results: Data from 429 older people were randomly. Among the 56.4% who were discharged, 57.9% had reduced ambulation capacity. Factors associated with reduced ambulation capacity at discharge were hospital stay higher than 20 days (OR: 3.5) and dependent ambulation capacity prior to Covid-19 (OR: 11.3). (4) Conclusion: More than half of the older people who survived hospitalized due to Covid-19 had reduced ambulation capacity at hospital discharge. Impaired ambulation prior to the infection, and a longer hospital stay were risks factors for reduced ambulation capacity.

Objectives Bone fractures are very common diseases, which can be caused by impact injuries or physiological disorders. Thus, the present review aimed to study the use of medicinal plants in the healing mechanism of bone fractures. Evidence acquisition Through research in the PubMed, Google Academic, and Scielo databases, this article reviews 11 ethnopharmacological studies and 34 preclinical studies on the biological actions of different plants in bone fracture healing mechanism. Results Indian tribes have highlighted in the plants ethnopharmacological study for various diseases, including bone fractures. However, despite the large citations of traditional use, technical-scientific studies are still scarce in the literature. Chenopodium ambrosioides, Piper sarmentosum, quadrangular Cissus, Ricinus communis and Radix salvia miltiorrhiza plants were the most studied in the literature regarding their osteogenic, angiogenic, anti-inflammatory and remodeling effects, acting on bone receptors, stimulating bone metabolism, increasing minerals uptake, and assisting in free radicals breakdown. Conclusion Thus, the medicinal plants use is promising in the field of bone regeneration, as well as being alternative when conventional therapies are unfeasible, increasing herbal medicines demand and popularity.

The bio-oil obtained by pyrolysis of Açaí (Euterpe oleracea Mart.) seeds at 450 ºC, 1.0 atmosphere, in technical scale, submitted to fractional distillation to produce biofuels-like fractions. The distillation of bio-oil carried out in a laboratory distillation column (Vigreux) of 30 cm. The physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) determined by official methods. The chemical functions present in distillation fractions determined by FT-IR and the chemical composition by GC-MS. The distillation of bio-oil yielded gasoline, light kerosene, and kerosene-like fuel fractions of 16.16, 19.56, and 41.89% (wt.), respectively. All the physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) increase with boiling temperature. The gasoline-like fraction is composed by 64.0% (area.) hydrocarbons and 36.0% (area.) oxygenates, while light kerosene-like fraction by 66.67% (area.) hydrocarbons and 33.33% (area.) oxygenates, and kerosene-like fraction by 19.87% (area.) hydrocarbons and 81.13% (area.) oxygenates.

In this paper we describe the potentialities of a tool for the visualization of experimental results directly on a three-dimensional model. The case study concerns the visualization of the results of a dynamic finite element analysis (FEA/FEM) applied to the calculation of seismic risk on works belonging to the Italian infrastructural heritage, specifically bridges, viaducts and overpasses. The project is based on finite element analysis performed on an exemplary set of 8 structures located on the Italian territory, performed by means of the open-source software framework OpenSees, according to the guidelines indicated in the Technical Standards for Construction NTC08. The application created for this project is classifiable as a webGIS, since all data are georeferenced and visualized on a map through an application executed through a browser. The graphical interface displays the interested works on the map of the Italian territory and allows to select them by mouse click. Following the selection, a 3D rendering of the model of the work and the surrounding terrain is shown, in which the results of the analysis are represented using color gradients directly on the three-dimensional model. The necessary tools are present for the selection of the type of result and for the animation in real time of the response of the work to the seismic action. The 3D representation is freely navigable by the user thanks to intuitive tools of panning, rotation and zoom through mouse and keyboard. The application takes advantage of HTML5, CSS and Javascript to show graphical features such as Cartesian diagrams of accelerograms used in modal analysis.

In this work we produced biochar by coffee waste and use it as filler in epoxy resin composite with the aim to increase their electrical properties. The biochar and biochar based composite electrical conductivity were studied in function of applied pressure and compared with carbon black and carbon black composite. The applied pressure has the aim to investigate the behaviour of filler in powder or dispersed in composite in function of compression. Results showed that even if the coffee biochar has less conductivity if compared with carbon black in powder form, it has better conductivity in composite if compared with carbon black. Composite mechanical properties were tested and they are generally improved respect to neat epoxy resin.

Recovery between physical efforts is essential for optimal performance in sports. Dietary supplements like cannabidiol (CBD) have been proposed to facilitate recovery and performance optimization. This systematic review aimed to: a) systematize the scientific evidence on CBD for recovery, b) associate CBD's biomedical properties with those required for optimal fatigue recovery, and c) recommend a future research agenda. Searches across databases identified 70 relevant studies from 1990-2022, including 38.6% preclinical, 31.4% clinical trials, and 30.0% reviews/meta-analyses across various populations like mice, rats, epileptics, and athletes. CBD demonstrated potentially beneficial properties for athlete recovery such as anti-inflammatory, neuroprotective, anxiolytic, and analgesic effects with doses ranging from 5-600mg administered orally, intravenously, and via other routes. However, rigorous confirmatory research specifically in athlete populations is lacking. While CBD appears promising for facilitating recovery and performance optimization, further randomized placebo-controlled trials are needed to test the acute and chronic effects of different CBD dosing regimens in athletes. Future research should focus on elucidating CBD's physiological mechanisms of action as they relate to post-exercise recovery, as well as its comparative effectiveness versus conventional medications and therapies. Advancing our understanding of CBD's role in athlete recovery could provide new therapeutic strategies to optimize recovery and performance.

The spread of high-performance personal computers, frequently equipped with powerful Graphic Processing Units (GPU), raised the interest on a set of techniques able to extract models of electromagnetic phenomena (and devices) directly from available examples of the desired behavior. Such approaches are collectively referred to as Machine Learning (ML). A typical representative ML approach is the so called “Neural Network” (NN). Using such data-driven models allows evaluating the output in a much shorter time when a theoretical model is available, or allows predicting the behavior of the systems and devices when no theoretical model is available. With reference to a simple yet representative benchmark electromagnetic problem, some of the possibilities and the pitfalls of the use of NN for the interpretation of measurements (inverse problem) or to obtain the required measurements (optimal design problem) are discussed. The investigated aspects include the choice of the NN model; the generation of the dataset(s); the selection of hyperparameters (hidden layers, training paradigm). Finally, the capabilities in the handling of ill-posed problems are critically revised.

Introduction: Leprosy, caused by Mycobacterium leprae is one of the oldest infectious diseases in human history and its eradication is linked to poverty control, lack of basic sanitation, the fragility of health, and education services. Objective: To evaluate the frequency of blood groups (ABO/Rh) and the sociodemographic and clinical profile of Angolan patients with Leprosy treated at the Anti-Tuberculosis and Leprosy Dispensary in Luanda, the capital city of Angola. Methodology: A descriptive, introspective, cross-sectional study with a quantitative approach was carried out with 102 patients of Luanda, in the second half of 2021. Results: Of the 102 patients included in the study, the majority belonged to the ORh+ group (51.9%), followed by the BRh+ group (27.4%) and ARh+ (18.6%), most were under 51 years of age ( 87.3%), with low education (54.9%), coming from urban areas (44.1%). As for clinical conditions, most had a multibacillary infection (93.1%), diagnosed mainly by smear microscopy (75.5%) without other infection (79.4%), some of them with complications (28.4%) and individuals with non-O blood group showed changes in the blood count. Conclusion: Leprosy seems to be common in ORh+ individuals, it continues to affect especially those residing in areas of population agglomerations and with low education, presenting itself as a multibacillary infection, where changes in the blood count are greater in non-O individuals.