Ultralong carbon nanotubes (UCNTs) are highly demanded for nanocomposites applications because of their magnificent physical and chemical properties. UCNTs are synthesized by catalytic chemical vapor deposition (CCVD) method and, before using as fillers in nanocomposites, should be purified from residual catalyst and non-CNT particles without significant destruction or scissoring of UCNTs. The role of water vapor for purification of UCNTs is investigated, the importance of water assistance in this process is confirmed. It was shown that wet air treatment of products of UCNTs CCVD synthesis under mild conditions can be used to decrease sufficiently residual catalyst content without significant carbon losses in comparison with the results obtained with dry air, while the residual iron content was shown to influence heavily on the subsequent oxidation of different forms of carbons, including UCNTs. The increasing of D/G ratio of Raman spectra after wet air treatment of products of UCNTs CCVD synthesis makes it possible to conclude that iron catalyst particles transform into iron oxides and hydroxides that caused inner structural strains and destruction of carbon shells improving removal of the catalyst particles by subsequent acid treatment. UCNTs purification with water assistance can be used to develop economically and ecologically friendly methods for obtaining fillers for nanocomposites of different applications.

The conformational preferences of the ester group have the potential to facilitate the large amplitude folding of long alkyl chains in the gas phase. They are monitored by Raman spectroscopy in supersonic jet expansions for the model system methyl butanoate, after establishing a quantitative relationship to quantum-chemical predictions for methyl methanoate. This requires a careful analysis of experimental details, and a simulation of the rovibrational contours for near-symmetric top molecules. The technique is shown to be complementary to microwave spectroscopy in quantifying coexisting conformations. It confirms that a C-O-C(=O)-C-C chain segment can be collapsed into a single all-trans conformation by collisional cooling, whereas alkyl chain isomerism beyond this five-membered chain largely survives the jet expansion. This sets the stage for the investigation of linear alkyl alkanoates in terms of dispersion-induced stretched-chain to hairpin transitions by Raman spectroscopy.

Background: Observational health data has the potential to be a rich resource to inform clinical practice and regulatory decision making. However, the lack of standard data quality processes makes it difficult to know if these data are research ready. The EHDEN COVID-19 Rapid Col-laboration Call presented the opportunity to assess how the newly developed open-source tool Data Quality Dashboard (DQD) informs the quality of data in a federated network. Methods: 15 Data Partners (DPs) from 10 different countries worked with the EHDEN taskforce to map their data to the OMOP CDM. Throughout the process at least two DQD results were collected and compared for each DP. Results: All DPs showed an improvement in their data quality between the first and last run of the DQD. The DQD excelled at helping DPs identify and fix conformance is-sues but showed less of an impact on completeness and plausibility checks. Conclusions: This is the first study to apply the DQD on multiple, disparate databases across a network. While study-specific checks should still be run, we recommend that all data holders converting their data to the OMOP CDM use the DQD as it ensures conformance to the model specifications and that a database meets a baseline level of completeness and plausibility for use in research.

The case of naturalization of the zebra mussel, Dreissena polymorpha (Pallas), in coun-tries lying beyond its native Ponto-Caspian range is remarkable as one of the first instances, when the scientific community as early as the mid-19th century was fully aware of the non-indigenous status of a particular species as well as of the need for the study and monitoring of this process. Based on a study of contemporary sources, I reconstruct the early response of the European naturalists (including those that today would be called ‘citizen scientist’) to the invasion of Dreissena and describe their attitudes to the problem, including the divergence of opinion about the origin and the means of dispersal of this bivalve species. An analysis of pa-pers of the English, French, German, and Russian authors published between 1774 and 1920 has shown that the invasion of D. polymorpha was by no means ‘silent’; quite opposite, it provoked an immediate reaction of naturalists, and the scientific agenda for the study of the new invader was proposed in England as early as 1838

A developing energy-saving approach of cold sintering in a pure aqueous medium was applied to the preparation of α-Al2O3 ceramics and performed on spark plasma sintering equipment. The initial γ-Al(OH)3 and γ-AlOOH powders and the cold-sintered ceramics were studied by X-ray diffraction analysis, infrared spectroscopy, thermal analysis, and scanning electron microscopy to reveal the chemical and structural transformations they experienced during the cold sintering. At 450°C and 70 MPa, initial γ-AlOOH transformed into a fragile α-Al2O3 material. Porous α-Al2O3 ceramics with about 60% porosity was obtained after cold sintering of γ-Al(OH)3 in the same conditions combined with subsequent annealing at 1250°C for 3 h. The role of water molecules in the studied processes was considered as the enhancement of structural mobility in the cold-sintered material due to its reversible hydroxylation similar to earlier investigated supercritical water action on the precursors during α-Al2O3 formation. Further improvement of the cold sintering setup and regimens would open prospects in α-Al2O3 ceramics manufacturing by an ecologically benign route.

The aim of this paper is to optimize thickness variation function of simply supported and cantilever beams, in terms of maximizing gaps between chosen neighboring frequencies and analyze obtained results. The optimization results are examined in terms of achieving the objective function (related to eigenproblem), but also in terms of their dynamics stiffness (forced vibrations excited by point harmonic load). In the optimization process, a Genetic Algorithm was used. Problems related to structural dynamics were solved by FEM implementation into the algorithm. Sample results were presented, and the developed algorithm was analyzed in terms of result convergence by examining several variable parameters. The authors demonstrated the validity of applying the described optimization tool to the presented problems. Conclusions were drawn regarding the correlation between stiffness and mass distribution in the optimized beams and the natural frequency modes in terms of which they were optimized.

To fill in the blanks for charophytes in the Caucasus to improve our knowledge of species distribution areas in Eurasia, a field survey and study of available specimens from Dagestan (North Caucasus, Russia) was conducted based on morphological observation and molecular genetic analysis. Seventeen new localities for six Chara species and one Tolypella species, with six new species and one new genus for the region studied, and one new species for the Caspian Sea region were found. Some species records changed the outline or filled in the gaps in the species distribution area. The presence of species with a distribution area mainly in the centre of Eurasia (C. globata, C. neglecta) with mainly Mediterranean – Middle East species (C. gymnophylla) is notable for this region, as well as for other studied regions of the Caucasus having a combination of species with different distribution areas. The frequent occurrence of C. gymnophylla points is similar to that in the Mediterranean region and the Middle East. Small brackish waterbodies at the coast of the Caspian Sea, freshwater mountain rivers, small waterbodies associated with them, and water reservoirs are the main habitats of charophytes in the regions. The habitat preference and distribution in the Caucasus allowed suggestion some species for protection. The absence of endemic species among charophytes from Dagestan and Caucasus contrasts with the flora of terrestrial magnoliophytes, which have a large number of endemic species.

The research presents a novel synthetic photosensitizer for photodynamic therapy (PDT) of malignant tumors - meso-tetra(3-pyridyl) bacteriochlorin, which absorbs at 747 nm (in the long-wavelength region of the spectrum) and is stable when stored in the dark. H2Py4BC demonstrates pronounced photoinduced activity in vitro against tumor cells of various genesis (IC50 varies from 21 to 68 nM for НЕр2, EJ, S37, CТ26, and LLC cultured cells) and provides in vivo pronounced antitumor efficacy in the treatment of mice bearing small or large S37, Colo26, and LLC metastatic tumors, as well as in the treatment of rats bearing RS-1 liver cholangioma. As a result, total regress of primary tumor nodules and cure of 40 to 100% of the animals were proved by the experiment criteria, MRI, and histological analysis. Meso-tetra(3-pyridyl) bacteriochlorin quickly penetrates and accumulates in the tumor tissue and internal organs of mice, and after 24 hours 80% of the dye is excreted from skin as well as 87% - 92% from liver, kidneys, and spleen.

Numerous types of oligonucleotide modifications have been developed since automated synthesis of DNA/RNA became a common instrument in the creation of synthetic oligonucleotides. Despite the growing number of types of oligonucleotide modifications under development, only a few of them, and moreover, their combinations have been studied wide enough in terms of their in-fluence on the properties of corresponding NA constructions. In the present study, a number of oligonucleotides with combinations of 3′ end lipophilic (single cholesteryl or pair of dodecyl residues) and phosphate backbone modifications were synthesized. The influence of the combi-nation of used lipophilic groups with phosphate modifications of various nature and different position on the efficiency of cell penetration was evaluated. Obtained results indicate that even a couple of phosphate modifications are able to affect a set of oligonucleotide properties in a complex manner and can remarkably change cellular uptake. These data clearly show that the strategy of using different patterns of modification combinations has great potential for the ra-tional design of oligonucleotide structures with desired predefined properties.

Optimum design and accurate control of the internal structure of the laser target materials remain an important goal for various laser physics experiments, especially for generating high flux photon and neutron beams. The low-density material is considered to be one of the most difficult for X-ray study due to its high transparency and imperceptible contrast. To produce clear visualization of foam containing sparse structures we used a high-quality monochromatic X-ray beam of synchrotron radiation source PETRA-III at DESY. The X-ray beam parameters allow tomographic scanning with application of phase contrast retrieval algorithms. A series of 3D images of foam-suspended glass microsphere inside the plastic cylinder were obtained with the quality high enough to observe the internal structure and to visualize uniformity, displacement and surface roughness on both sides of the microsphere. The main object under investigation was a CH-plastic capillary including 10 mg/cc CHO-foam with the centered glass microsphere. The results of this work demonstrate that tomographic visualization based on a high quality X-ray radiation and phase contrast analysis is an effective and useful technique for development of new laser targets containing structured low density materials.

OSI model used to be common network model for years. In the case of ad hoc networks with dynamic topology and difficult radio communications conditions, gradual departure is happening from the classical kind of OSI network model with a clear delineation of layers (physical, channel, network, transport, application) to the cross-layer approach. The layers of the network model in ad hoc networks strongly influence each other. Thus, the cross-layer approach can improve the performance of an ad hoc network by jointly developing protocols using interaction and collaborative optimisation of multiple layers. The existing cross-layer methods classification is too complicated, because it’s based on the whole manifold of network model layers combinations, regardless their importance. In this work, we review ad hoc networks cross-layer methods, propose the new useful classification of cross-layer methods, and show future research directions in ad hoc networks cross-layer methods development. The proposed classification can help to simplify the goal-oriented cross-layer protocol development.

Porous α-Al2O3 ceramics is a highly demanded material for multitude applications such as filters, substrates, biomedicine materials, etc. Despite the availability of the raw materials, a challenge of their technology is in a high energy budget caused by the sintering above 1500 °C. For a cold sintering processing (CSP) of ceramics, the lowering of α-Al2O3 sintering temperature is one of the most urgent challenges at the background of its rapid development. The current paper for the first time demonstrates the solution of the mentioned problem by the CSP of α-alumina ceramics in a presence of pure water as a transient liquid. The manufactured materials were examined by XRD analysis; the evolution of their microstructures during the CSP was revealed by SEM, and the porosity evaluated by the Archimedes method. The ceramics with an open porosity up to 36 % was produced at 380-450 °C, 220 MPa in 30 min. An increase in the pressure was found to impede α-Al2O3 formation from γ-AlOOH. The development of the microstructure was discussed within the frameworks of the dissolution-precipitation model and the homogenous nucleation. The results of the SEM study pointed to the coalescence of γ-AlOOH grains during the CSP.

Advancements in computer vision are rapidly revolutionizing the way traffic agencies gather roadway geometry data, leading to significant savings in both time and money. Utilizing aerial and satellite imagery for data collection proves to be more cost-effective, more accurate, and safer compared to traditional field observations, considering factors such as equipment cost, crew safety, and data collection efficiency. Consequently, there is a pressing need to develop more efficient methodologies for promptly, safely, and economically acquiring roadway geometry data. While image processing has previously been regarded as a time-consuming and error-prone approach for capturing these data, recent developments in computing power and image recognition techniques have opened up new avenues for accurately detecting and mapping various roadway features from a wide range of imagery data sources. This research introduces a novel approach combining image processing with a YOLO-based methodology to detect turning lane pavement markings from high-resolution aerial images, specifically focusing on Florida's public roadways. Upon comparison with ground truth data from Leon County, Florida, the developed model achieved an average accuracy of 87% at a 25% confidence threshold for detected features. Implementation of the model in Leon County identified approximately 3,026 left turn, 1,210 right turn, and 200 center lane features automatically. This methodology holds paramount significance for transportation agencies in facilitating tasks such as identifying deteriorated markings, comparing turning lane positions with other roadway features like crosswalks, and analyzing intersection-related accidents. The extracted roadway geometry data can also be seamlessly integrated with crash and traffic data, providing crucial insights for policymakers and road users.

Silicon nanoparticles (SiNPs) are highly promising for biological and biomedical applications, including bioimaging, due to their unique opltical properties (i.e. strong fluorescence and very high photostability). Their low or negligible in vitro toxicity has been reported, but in vivo toxicity and biological effects of SiNPs are still uncertain. Uncoated SiNPs were dispersed in distilled water via sonication, and their rapid aggregation was observed (319.0 ± 2.4 nm particle size). In vivo toxicity was studied using Danio rerio embryos and larvae. Rapid aggregation in their incubation medium was observed; besides that, SiNPs at 25 mg/L or higher concentration induced swim bladder malformation and/or death of the fish. The estimated LC50 value for 7-day larvae was 180 mg/L. This is the first in vivo toxicity study of uncoated and unfunctionalized SiNPs. To achieve better stability in biological media and lower toxicity, SiNPs should be covered with hydrophilic layers, but their absorption by cellular membranes may be weaker in this case.

The genus Fritillaria belongs to the widely distributed family Liliaceae. The bulbs of Fritillaria ussuriensis and Fritillaria cirrhosa are valuable herbaceous medicinal ingredients. However, they are still used indiscriminately in herbal medicine. Identification and molecular phylogenic analysis of Fritillaria species is therefore required. Here, we report the complete chloroplast (cp) genome sequences of F. ussuriensis and F. cirrhosa. The two Fritillaria cp genomes were 151,524 and 151,083 bp in length, respectively, including a pair of inverted repeat regions (52,678 and 52,156 bp) separated by a large single copy region (81,732 and 81,390 bp) and small single copy region (17,114 and 17,537 bp). A total of 111 genes in F. ussuriensis and 112 in F. cirrhosa comprised 77 protein-coding genes in F. ussuriensis and 78 in F. cirrhosa, 30 tRNA genes, and four rRNA genes. The gene order, content, and orientation of the two Fritillaria cp genomes exhibited the general structure of flowering plants, and were similar to those of other Fritillaria species. Comparison of the six Fritillaria species’ cp genomes indicated seven highly divergent regions in intergenic spacers and in the matK, rpoC1, rpoC2, ycf1, ycf2, ndhD, and ndhF coding regions. We established the position of the six species through phylogenic analysis. The complete chloroplast genome sequences of two Fritillaria species will be useful genomics resources for identification of Fritillaria species and for studying the phylogenetic relationship among Fritillaria species within the Liliaceae family.

Poplar (Populus) is a genus of woody plants of value for the pulp industry, green energy, urban landscaping, soil phytoremediation and as an ornamental plant. Due to the increasing economic importance of poplar, there is a need to ensure its stable growth by increasing its resistance to pathogens, as one of the main problems in poplar cultivation is its susceptibility to numerous diseases. Currently, breeding poplars with reduced susceptibility to infections is receiving increasing attention. Genetic engineering can produce organisms with improved traits faster than traditional methods, and with the development of CRISPR/Cas-based genome editing systems, scientists have a new highly efficient tool at their disposal to create valuable genotypes. In this review, we summarize recent research data on poplar diseases, the biology of their pathogens, and how these plants resist pathogens. In the final section, we discuss genetic engineering, genome editing, and microbiome strategies that we believe are suitable for obtaining new improved poplar lines.

Maxillofacial defects, arising from trauma, oncological disease or congenital differences, detrimentally affect everyday life. Prosthetic repair offers the aesthetic and functional reconstruction with the help of materials mimicking natural tissues, among which polymers take unprecedented role. The three-dimensional (3D) printing techniques based on the computer-aided design, where polymers are essential, provide a rapid and cost-effective workflow protocol to perfectly restore patient-specific anatomy for prosthetics. This review discusses the main 3D printing approaches to maxillofacial prostheses fabrication: extrusion and lithography, which are radically preferable to the traditional methods. The main assessment criteria, affording the polymer implementation in 3D printing of prostheses, as well as the characteristics of the key advanced polymers, are considered. The success of the prosthesis is shown to be largely dependent on the retention system, predominantly using polymers in the form of adhesives and osseointegrated implants as a support for the prosthesis. The approaches and technological prospects are also discussed in the context of specific aesthetic restoration on the example of the nasal, auricle and ocular prostheses. 3D printing techniques determine the development of personalized approaches to improve aesthetic and functional effect of prosthetics in patients with maxillofacial defects.

This paper focuses on the combination of the method of moments and the wire-grid approximation as an effective computational technique for modeling symmetrical antennas with low computational cost and quite accurate results. The criteria and conditions for the use of wire-grid surface approximation from various sources are presented together with new recommendations for modeling symmetrical antenna structures using the wire-grid approximation. These recommendations are used to calculate the characteristics of biconical and horn antennas at different frequencies. The results obtained using different grid and mesh settings are compared to those obtained analytically. Moreover, the results are compared to those obtained using the finite difference time domain numerical method, as well as the measured ones. All results are shown to be in a good agreement. The used recommendations for building a symmetrical wire-grid of those symmetrical antenna elements provided the most advantageous parameters of the grid and mesh settings and the wire radius, which are able to give a quite accurate results with low computational cost. Additionally, the known equal area rule was modified for a rectangular grid form. The obtained radiation patterns of a conductive plate using both the original rule and the modified one are compared with the electrodynamic analysis results. It is shown that the use of the modified rule is more accurate when using a rectangle grid form.

Eight reconstructions of temperature in the Northern Hemisphere covering 1192-2015 years were analyzed using both Fourier, wavelet and principal component approaches. A hemispheric-scale cyclicity with a period of 170-250 years was found present in Northern Hemisphere temperature for more than the last millennium. It is shown that this variation may have a certain contribution to warming in the first half of the 20th century. However, the last 4-5 decades are most likely a period of decline of this cycle. Possible origins of the revealed bicentennial periodicity are discussed.

Numerous experimental and theoretical studies undertaken to determine the effective-stress coefficient for seismic velocities in rocks stem from the importance of this geomechanical parameter both for monitoring changes in rock saturation and pore pressure distribution in connection with reservoir production, and for overpressure prediction in reservoirs and formations from seismic data. The present work pursues a task to determine, in the framework of a low-frequency laboratory study, the dependence of the elastic moduli of n-decane saturated sandstone on the relationship between pore and confining pressures. The study was conducted on a sandstone sample with high quartz and notable clay content in the quasi-static regime, when the 100 ml tank filled with n-decane was directly connected to the pore space of the sample. The measurements were carried out at a seismic frequency of 2 Hz and strains, controlled by semiconductor strain gauges, not exceeding 10-6. The study was performed using a forced-oscillation laboratory apparatus utilizing stress-strain relationship. The dynamic elastic moduli have been measured in two sets of experiments: at constant pore pressures of 0, 1 and 5 MPa and differential pressure (defined as a difference between confining and pore pressures) varied from 3 to 19 MPa; and at а constant confining pressure of 20 MPa and pore pressure varied from 1 to 17 MP. It was shown that the elastic moduli obtained in the measurements are in good agreement with the Gassmann moduli calculated for the range of differential pressures used in our experiments, which corresponds to the effective-stress coefficient equal to unity.

Antiangiogenic therapy (AAT) is an indirect oncological modality which is aimed at disruption of cancer cells nutrient supply. Invasive tumors have been shown to possess inherent resistant to this treatment, while compactly growing benign tumors react to it by shrinkage. It is generally accepted that AAT by itself is not curative. This study presents a mathematical model of non-invasive tumor growth with physiologically justified account of alteration of microvasculature and biomechanical aspects during tumor growth and AAT. In untreated setting the model reproduces tumor growth with saturation, where the maximum tumor volume depends on the level of angiogenesis. The outcomes of simulations of AAT depend on the tumor size at the moment of treatment initiation. If it is close to the stable size of avascular tumor grown in absence of angiogenesis, then the tumor is rapidly stabilized by AAT. Treatment of large tumors is accompanied by displacement of normal tissue due to the tumor shrinkage. During it, microvasculature undergoes distortion which degree depends on the displacement distance. As it affects tumor nutrient supply, the stable size of a tumor that undergoes AAT negatively correlates with its size at the beginning of treatment. For sufficiently large initial tumors, the long-term survival of tumor cells is compromised by competition with normal cells for severely limited inflow of nutrients, which makes AAT effectively curative.

In this paper, we continue the research cycle on the properties of convolutional neural network-based image recognition systems and ways to improve noise immunity and robustness [1]. Currently, a popular research area related to artificial neural networks is adversarial attacks. The effect of adversarial attacks on the image is not highly perceptible to the human eye, also it drastically reduces the neural network accuracy. Image perception by a machine is highly dependent on the propagation of high frequency distortions throughout the network. At the same time, a human efficiently ignores high-frequency distortions, perceiving the shape of objects as a whole. The approach proposed in this paper can improve the image recognition accuracy in the presence of high-frequency distortions, in particular, caused by adversarial attacks. The proposed technique makes it possible to measure up the logic of artificial neural network to that of a human, for whom high-frequency distortions are not decisive in object recognition.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

We have found a region in the northwestern Japan Sea near the Subpolar Front where mesoscale eddies regularly form and circulate. The anticyclonic eddy with a strong dynamic feature, vertically extended to the bottom (~3500 m), multilayer core structure and extreme values of temperature and salinity was sampled there in the cruise in May 2004. The altimetry-based eddy tracking showed that it had a life span of nine months with the size reaching 120 km. CTD observational data were used to explore the eddy’s features and vertical structure. The eddy had a multilayer core with different thermohaline characteristics which could be originated by eddy interaction with the surrounding waters during its life. The evolution of the eddy has been studied and analyzed with the help of altimetry-based Lagrangian indicators of water motion. Performing the particle-tracking numerical experiments, we computed the Lagrangian maps that contain information on the origin of water inside the eddy core and its ‘age’ on every day of the eddy’s life. Inspecting daily-computed Lagrangian maps, we documented the essential events in the evolution of the eddy including its formation, splitting, merger, entrainment and detrainment of water, erosion and eventual decay. All these observations have been verified with the infrared satellite images. The new Lagrangian technique has been applied to calculate day by day the content of water of various origin (coastal, subtropical and subarctic) entrained into the eddy core. It has been found that the surface core has been filled mainly with subtropical water originated in the southern flank of the Subpolar Front. The episodes with cardinal changes of ratio of different water types have been recorded and verified with the infrared satellite images and maps of the origin of water inside the eddy core.

New antiviral agents are essential to improving treatment and control of SARS-CoV-2 infections that can lead to the disease COVID-19. Antimicrobial peptoids are sequence-specific oligo-N-substituted glycine peptidomimetics that emulate the structure and function of natural antimicrobial peptides but are resistant to proteases. We demonstrate antiviral activity of a new peptoid (TM9) against the coronavirus, murine hepatitis virus (MHV), as a closely related model for the structure and antiviral susceptibility profile of SARS-CoV-2. This peptoid mimics the human cathelicidin LL-37, which has also been shown to have antimicrobial and antiviral activity. In this study TM9 was effective against three murine coronavirus strains, demonstrating the therapeutic window is large enough to allow use of TM9 for treatment. All three isolates of MHV generated infection in mice after 15 min of exposure by aerosol using the Madison aerosol chamber and all three viral strains could be isolated from the lungs throughout the 5-day observation period post-infection, with the peak titers on day 2. MHV-A59 and MHV-A59-GFP were also isolated from liver, heart, spleen, olfactory bulbs, and brain. These data demonstrate that MHV serves as a valuable natural murine model of coronavirus pathogenesis in multiple organs, including the brain.

Barrett’s esophagus (BE) is a premalignant lesion for esophageal adenocarcinoma (EAC). Development of Barrett’s esophagus is caused by biliary reflux that provokes intensive mutagenesis in stem cells of epithelium in distal esophagus and gastro-esophageal junction. Other possible cell origins of Barrett’s esophagus include stem cells of mucosal esophageal glands and their ducts, of stomach, residual embryonic cells and circulating bone marrow stem cells. Classic conception of healing of caustic lesion was replaced by idea of cytokine storm that forms inflammatory microenvironment for phenotypic shift toward intestinal metaplasia of distal esophagus. The review summarizes contemporary concepts of BE and EAC pathogenesis.

The work is devoted to the search for effective solutions to the applied problem of early diagnostics of plant stress in the conditions of smart farming and based on modern explicable artificial intelligence (XAI). The study mostly oriented on the theory and practice of XAI, focused on the use of hyperspectral imagery (HSI) and Thermal Infra-Red (TIR) sensor data at the input of a neural network. The first our goal is to build an XAI neural network, explainable due to its structure, the input of which is a datascientist oriented HSI 'explanator', and the output is a biologist oriented TIR 'explanator'. In the middle is SLP-regressor which solves the universal problem of training HSI pixels to temperatures of plants, needed for early plant stress diagnostic. The result can be considered as prototype of a special XAI explanator which is assigned to transform explanator specialized on area 1 onto explanator specialized on area 2. Using this HSI-TIR explanator we ensured the follows: extend HSI data by TIR attribute; providing TIR data for early diagnostic of plant stress; reducing dimensionality HSI needed for TIR training 25 times (from 204 to 8) preserving the same accuracy of temperature prediction (RMSE=0.2-0.3C). This reducing was achieved without using PCA methods. The constructed model is computationally efficient in training: the average training time is significantly less then 1 min (Intel Core i3-8130U, 2.2 GHz, 4 cores, 4 GB). One of the 8 channels, 820 nm, is the leader in correlation with TIR, what allows building local linear temperature prediction functions.

Electron beam treatment of ZnS:Cu,Br (Cu activator content 0…0.6%wt.) radioluminescent phosphors as well as charge mixture with the electron energy 900 keV and absorbed dose of 600 kGy resulted in a enhancement of brightness up to 80%. The increased brightness is due to increase of content of wurtzite phase relative to sphalerite one with formation of wurtzite/sphalerite nanocomposite structure. Transformation of crystal structure is accompanied with corresponding change in content of active surface centers characteristic for sphalerite and wurtzite phases. A model describing surface centers of ZnS:Cu,Br radioluminescent phosphor is suggested.

In recent years, antibacterial coatings have become a significant approach in the global fight against bacterial pathogens. Developments in materials science, chemistry and biochemistry have led to a plethora of materials and chemical compounds that have potential for creating antibacterial coatings. Nonetheless, there has been insufficient consideration given to the analysis of the techniques and technologies used to apply these coatings. Among the various inorganic coating techniques, Atomic Layer Deposition (ALD) is noteworthy. It enables the successful synthesis of high-purity inorganic nanocoatings on surfaces of complex shape and topography, while also providing precise control over their thickness and composition. ALD has various industrial applications, but its practical application in medicine is still limited. In recent years, a substantial number of papers have been published on the suggested implementation of thin films and coatings produced through ALD in medicine, notably those with antibacterial properties. The aim of this paper is to carefully evaluate and analyse the relevant literature on this subject. Simple oxide coatings, including TiO2, ZnO, Fe2O3, MgO, and ZrO2, were examined, as well as coatings containing metal nanoparticles such as Ag, Cu, Pt, and Au, and mixed systems such as TiO2-ZnO, TiO2-ZrO2, ZnO-Al2O3, TiO2-Ag, and ZnO-Ag. Through comparative analysis, we have been able to draw conclusions on the effectiveness of various antibacterial coatings of different compositions, including key characteristics such as thickness, morphology, and crystal structure. ALD has been analysed in its use for developing antibacterial coatings for various applications. Furthermore, assumptions regarding the most promising development areas have been presented.

This research is completed in development of researches devoted to relations between elastic modulus (MoE) and thermal expansivity (CTe) of different materials. This study experimentally confirmed the relation of MoE and CTe for thermosetting polymers and FRPs both under normal and heating temperatures. As the thermosetting polymers, the epoxy compositions were used and glass fiber and mineral additives for FRP. The experiment was based on dilatometric and elastic deformations’ testing. Also, the relaxation model of MoE/CTe was proposed, that is based on physical properties of polymers’ supramolecular structures. The comparative analyzing of MoE/CTes’ different models is done. The most accurate models are determined, and the relaxation model has demonstrated the high accuracy.

Economic expedience of waste heat recovery systems (WHRS), especially for low temperature difference applications, is often questionable due to high capital investments and long pay-back periods. By its simple design isobaric expansion (IE) machines could provide a viable pathway to utilize otherwise unprofitable waste heat streams for power generation and particularly for pumping liquids and compression of gases. Different engine configurations are presented and discussed. A new method of modelling and calculation of the IE process and efficiency is used on IE cycles with various pure and mixtures as a working fluid. Some interesting cases are presented. It is shown in this paper, that the simplest non-regenerative IE engines are efficient at low temperature differences between a heat source and heat sink. Efficiency of non-regenerative IE process with pure working fluid can be very high approaching Carnot efficiency at low pressure and heat source/heat sink temperature differences. Regeneration permits to increase efficiency of the IE-cycle to some extent. Application of mixed working fluids in combination with regeneration permits to significantly increase the range of high efficiencies to much larger temperature and pressure differences.

A total of 281 coleopteran species from 41 families were recorded from different sites of an abandoned cut-over peatland designated as the Carbon Measurement Supersite in Kaliningrad Oblast. This beetle assemblage is considered as a baseline (pre-impact) faunal assemblage for the further investigations during the ‘before-after’ (BA) or ‘before-after control-impact’ (BACI) study on a peatland that is planned to be rewetted. The spontaneously revegetated peatland has a less specialised beetle assemblage than at an intact raised bog. Tyrphobiontic species are completely absent from the peatland, while some tyrphophiles (5.3% of the total beetle fauna) are still found as remnants of the former raised bog communities. The predominant coenotic coleopteran group is tyrphoneutral generalists from various non-bog habitats (72.9%). The species composition is associated witho the structure vegetation of the disturbed peatland (fragmentary Sphagnum cover, lack of open habitats, and widespread birch coppice or tree stand), which does not correspond to that of a typical European raised bog. The sampled coleopteran assemblage is divided into several relative ecological groups, whose composition and peculiarities are discussed separately. Possible responses to the rewetting measurements in different coleopteran groups are predicted and briefly discussed. A complex assemblage of stenotopic peatland-specialised tyrphophiles (15 spp.) and the most abundant tyrphoneutral generalists (31 spp.) were assigned as indicators for the environmental monitoring of peatland development.

The paper presents the results of experimental studies and mathematical modeling of the effect of stress accumulation in thermosetting epoxy polymer "hot" curing on anhydride hardener. Stress accumulation occurs under cyclic thermomechanical action in a locked rod, similar effects are observed, for example, in thermoplastic elements subjected to the combined effect of mechanical loads and variable temperatures. Experimental results have shown that under cyclic thermomechanical loading during exploitation it is possible to accumulate residual stresses in the thermosetting polymer. A multi-element structural mathematical model with memory for thermomechanical load, which allows to consider the accumulation of residual thermal stresses, has been proposed. The results of modeling and experiment are compared. Based on the results, corrections are made in the approach to the application of this model to thermosetting polymers such as the epoxy resin under study. Considering the corrections, a good agreement (the difference is from 1 to 6%) with the results of experimental determination of stresses under complex cyclic thermomechanical load was obtained.

The effect of coal hydrophilic particles in water-glycerol drops on the maximum diameter of spreading along a hydrophobic solid surface is experimentally studied by analyzing the velocity of internal flows by Particle Image Velocimetry. The grinding fineness of coal particles was 45-80 μm and 120-140 μm, their concentration was 0.06 wt.% and 1 wt.%. The impact of particle-laden drops on a solid surface occurred at Weber numbers (We) from 30 to 120. It is revealed the interrelated influence of We and the concentration of coal particles on changes in the maximum absolute velocity of internal flows in a drop within the kinetic and spreading phases of the drop-wall impact. A physical model is formulated for internal convective flows in the longitudinal section of a drop parallel to the plane of the solid wall. The kinetic energy of translational motion of coal particles in a spreading drop compensates for the energy expended by the drop on sliding friction along the wall. At We=120, the inertia-driven spreading of the particle-laden drop is mainly determined by the dynamics of the deformable Taylor rim. An increase in We contributes to more noticeable differences in the convection velocities in spreading drops. When the drop spreading diameter rises at the maximum velocity of internal flows, a growth of the maximum spreading diameter occurs. The presence of coal particles causes a general tendency to reduce the drop spreading.

An actual problem of inertial navigation related to the creation of a multifunctional device that performs the functions of a meter for both angular velocities and linear accelerations is considered. The possibility of constructing such a device based on a hybrid-type modulation micromechanical gyroscope has shown. The ability to measure linear accelerations has provided by the presence of a small symmetrical distance between the axes of the elastic suspension relative to the center of mass of the sensor element. A mathematical model of the device ("heavy" gyroscope) as a high-quality three-dimensional oscillatory system is constructed. It has shown numerically that the reaction of the system to the movement of an object has, along with precession, the observed nutation. This allows you to develop an algorithm for separating information about the angular and linear motion of the base and implement a two-component angular velocity meter and a two-component linear acceleration meter in one device.

Since streptomycin discovery, actinomycetes were the main source for new antibiotics, but after the Golden age (1950-1960^th) the discovery rate significantly decreased. The high probability to rediscover well-known antibiotics led to a reduction in interest in soil bacteria as a source for new antibiotics. At the same time, actinomycetes remain a very promising reservoir for searching for new active molecules. In this work, we present several reporters containing eye-visible fluorescent protein genes, which can be used to increase the efficiency of determining the mechanism of antibiotics at the very initial stage of screening. Presented reporters and the following pipeline were optimized given the involvement of citizen scientists without specialized skills and equipment in order to utilize the reservoir of soil bacteria in the search for new antibiotic producers. The combination of mechanism-based approaches and civil science has proved its effectiveness in practice revealing a significant increase in the screening rate. Two new strains Streptomyces sp. KB-1 and BV113 were found to produce antibiotics pikromycin and chartreusin, respectively, demonstrating the efficiency of the pipeline.

Model animals are employed in experiments as substitutes for human tissues and fluids, particularly when accessing particular human samples (such as cerebrospinal fluid, brain, ocular tissues, etc.) poses significant challenges or is ethically constrained. Nonhuman primates are frequently regarded as superior animal models for investigating human ophthalmological diseases. However, despite this recognition, the metabolomic composition of ocular tissues in non-human primates remains predominantly unexplored. In this work, we present a dataset on metabolite concentrations in serum and ocular tissues, including aqueous humor (AH), vitreous humor (VH), and lens, in two Macaque species: crab-eating macaque (Macaca fascicularis) and rhesus macaque (Macaca mulatta). A total of 99 compounds were quantified in 45 samples, shedding light on the previously unknown metabolomic profiles of primate eye tissues.

In this work, the possibility of fabrication magneto-optical ceramics by vacuum sintering of compacts prepared by electrophoretic deposition (EPD) from suspensions of (Ho0.95La0.05)2O3 (HoLa) nanopowders made by self-propagating high-temperature synthesis and (Y0.9La0.1)2O3 (YLa) nanopowders made by laser synthesis was systematically investigated. The processes of the formation of bulk one- and two-layer compacts by the EPD method from non-aqueous suspensions of nanopowders was studied. The use of acetylacetone and polyvinyl butyral (PVB) was shown to make it possible to obtain stable alcohol suspensions of the nanopowders characterized by high zeta potential values (+29…+80 mV) and to carry out a stable EPD process. One-layer compacts were made from the YLa and HoLa nanopowders with a density of 30–43%. It was found out that the introduction of PVB into the suspension leads to a decrease in the mass and thickness of the green bodies deposited, but does not significantly affect their density. A possibility to make two-layers (YLa/HoLa) compacts with a thickness of up to 2.6 mm and a density of up to 46% was demonstrated. Sintering such compacts in a vacuum at a temperature of 1750°C for 10 hours leads to the formation of ceramics with a homogeneous boundary between the YLa/HoLa layers and thickness of the interdiffused ions layer of about 30 μm.

Soil and Water Assessment Tool (SWAT) was used to simulate five glacierized river basins that are global in coverage and vary in climate. The river basins included the Narayani (Nepal), Vakhsh (Central Asia), Rhone (Switzerland), Mendoza (Central Andes, Argentina), and Central Dry Andes (Chile) with a total area of 85,000 km2. A modified SWAT snow algorithm was applied in order to consider spatial variation of associated snow melt /accumulation by elevation band across each subbasin. In the previous studies, melt rates varied as a function of elevation resulting from an air temperature gradient while the snow parameters were constant throughout the entire basin. A major improvement of the new snow algorithm is separating the glaciers from seasonal snow based on their characteristics. Two SWAT snow algorithms were evaluated in simulation of monthly runoff from glaciered watershed: 1) the snow parameters are lumped (i.e. constant throughout the entire basin) and 2) the snow parameters are spatially variable based on elevation band-subbasin (i.e. modified snow algorithm). Applying the distributed SWAT snow algorithm improved the model performance in simulation of monthly runoff with snow-glacial regime, so that mean RSR decreased to 0.49 from 0.55 and NSE increased to 0.75 from 0.69. Improvement of model performance was negligible in simulation of monthly runoff from the basins with monsoon runoff regime.

Extensive genome structure variation, such as copy number variations (CNVs) and presence/absence variations, is the basis for the remarkable maize genetic diversity; however, the effect of CNVs on maize herbivory defense remains largely underexplored. Here, we report that the naturally occurring duplication of the maize 9-lipoxygenase gene, ZmLOX5, leads to increased resistance of maize to herbivory by fall armyworms (FAW). Previously, we showed that ZmLOX5-derived oxylipins are required for defense against chewing insect herbivores and identified several inbred lines, including Yu796, that contained duplicated CNVs of ZmLOX5, referred to as Yu796-2×LOX5. To test whether introgression of the Yu796-2×LOX5 locus into the herbivore-susceptible B73 background that contains a single ZmLOX5 gene is a feasible approach to increase resistance, we generated a series of near-isogenic lines that contained either 2, 1 or 0 copies of the Yu796-2×LOX5 locus in the B73 background by six back crosses (BC6). Droplet digital PCR (ddPCR) confirmed the successful introgression of the Yu796-2×LOX5 locus in B73. The resulting B73-2×LOX5 inbred line displayed increased resistance against FAW associated with increased expression of ZmLOX5, increased wound-induced production of its primary oxylipin product, the α-ketol, 9-hydroxy-10-oxo-12(Z),15(Z)-octadecadienoic acid (9,10-KODA), and the downstream defense hormones regulated by this molecule, 12-oxo-phytodienoic acid (12-OPDA) and abscisic acid (ABA). Surprisingly, wound-induced JA-Ile production was not increased in B73-2×LOX5, resulting from the increased JA catabolism. Furthermore, B73-2×LOX5 displayed enhanced drought tolerance likely due to increased ABA and 12-OPDA content. Taken together, this study revealed that the duplicated CNV of ZmLOX5 quantitively contributes to maize antiherbivore defense and presents proof-of-concept evidence that the introgression of naturally occurring duplicated CNVs of a defensive gene into the productive, but susceptible, crop varieties is a feasible breeding approach for enhancing plant resistance to herbivory and tolerance to abiotic stress.

Nowadays, the imidazolium-based ionic liquids containing acetate counter-ions are attracting much attention as both highly selective absorbents of the acidic gases and CO₂ carriers in the supported ionic liquid membranes. In this regard, the investigation of the gas transport properties of such membranes may be appropriate for better understanding of various factors affecting the separation performance and the selection of the optimal operating conditions. In this work, we have tested CH₄, CO₂ and H₂S permeability across the SILM impregnated by 1-butyl-3-methylimidazolium acetate (bmim[ace]) with the following determination of the ideal selectivity in order to compare the facilitated transport membrane performance with the SILM that dissolves acidic gases physically, namely, containing 1-butyl-3-methylimidazolium tetrafluoroborate (bmim[BF₄]). Both SILMs have showed modest individual gases permeability and ideal selectivity of CO₂/CH₄ and H₂S/CH₄ separation that achieves values up to 15 and 32, respectively. The effect of the feed gas mixture composition on the permeability of acidic gases and permeselectivity of the gas pair was investigated. It turned out that the permeation behavior for the bmim[ace]-based SILM toward the binary CO₂/CH₄, H₂S/CH₄ and ternary CO₂/H₂S/CH₄ mixtures was featured with high acidic gases selectivity due to the relatively low methane penetration through the liquid phase saturated by acidic gases.

Soil-borne Trichoderma spp. have been extensively studied for their biocontrol activities against pathogens and growth promotion ability with plants. However, the beneficial effect of Trichoderma on inducing resistance against insect herbivores has been considered only recently. Among diverse Trichoderma species, consistent with previous reports, we showed that root colonization by T. virens triggered induced systemic resistance (ISR) to leaf-infecting fungal pathogens. Whether T. virens induces ISR to insect pests has not been tested before. In this study, we investigated whether T. virens affects jasmonic acid (JA) biosynthesis and defense against fall armyworm (FAW) and western corn rootworm (WCR). Unexpectedly, the results showed that T. virens colonization of maize seedlings grown in autoclaved soil suppressed wound-induced production of JA, resulting in reduced resistance to FAW. Similarly, the bacterial endophyte Pseudomonas chlororaphis 30-84 suppressed systemic resistance to FAW due to reduced JA. Further comparative analyses of the systemic effects of these endophytes when applied into sterile or non-sterile field soil showed that both T. virens and P. chlororaphis 30-84 triggered ISR against hemibiotrophic fungal pathogen Colletotrichum graminicola in both soil conditions, but only suppressed resistance to FAW in sterile soil. In contrast to the effect on FAW defense, T. virens colonization of maize roots suppressed WCR larvae survival and weight gain. This is the first report suggesting the potential role of T. virens as a biocontrol agent against WCR.

Physics of high-Tc superconducting cuprates is obscured by the effect of strong electronic correlations. One way to overcome the problem is to seek for an exact solution at least within the small cluster and expand it to the whole crystal. Such an approach is in the heart of the cluster perturbation theory (CPT). Here we develop CPT for the dynamic charge and spin susceptibilities (spin-CPT), within which the correlation effects are explicitly taken into account by the exact diagonalization. We apply spin-CPT to the effective two-band Hubbard model for the cuprates obtained from the three-band Emery model and calculate one- and two-particle correlation functions, namely, spectral function and spin and charge susceptibilities. Doping dependence of the spin susceptibility was studied within spin-CPT and CPT-RPA that is the CPT generalization of the random phase approximation (RPA). Both methods produce the low energy response at four incommensurate wave vectors in qualitative agreement to the results of the inelastic neutron scattering on overdoped cuprates.

In this work, the surface of poly(ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670-1310 nm was hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spec-troscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurement were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymeriza-tion time 60 min, monomer concentration of 30% and distance from the UV-source 7 cm. The wa-ter contact angle of the modified membranes reached 97° which is 51o for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effect of membrane pore size, the degree of grafting and salt concentration on the performance of membrane distillation process was investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.

We present a very computationally light and fast approximation algorithm and then verify it with genetic algorithm and simulated annealing. We show that our algorithm is on par with GA and SA in terms of output produced while having a tightly bounded time complexity. Our algorithm works best when there is a strong positive correlation between the reliability of a component and its cost. We present two algorithms with the same essence. One of them is system cost bounded and the other is target reliability bounded. Our proposed algorithm works on a subsystem level redundancy instead of component level redundancy.

A hallmark of Alzheimer’s disease (AD) are the proteinaceous aggregates formed by the amyloid-beta peptide (Aβ) that is deposited inside the brain as amyloid plaques. The accumulation of aggregated Aβ may initiate or enhance pathologic processes in AD. According to the amyloid hypothesis any agent that has the capability to inhibit Aβ aggregation and/or destroy amyloid plaques represents a potential disease modifying drug. In 2023, a humanized IgG1 monoclonal antibody (lecanemab) against the Aβ soluble protofibrils was approved by US FDA for AD therapy thus providing compelling support to the amyloid hypothesis. To acquire a deeper insight on the in vivo Aβ aggregation, various animal models, including aged herbivores and carnivores, non-human primates, transgenic rodents, fish and worms are widely exploited. This review is based on the recent data obtained using transgenic animal AD models and presents experimental verification of the critical role in Aβ aggregation seeding of the interactions between zinc ions, Aβ with the isomerized Asp7 (isoD7- Aβ) and the α4β2 nicotinic acetylcholine receptor.

Natural cytokinins are a promising group of cytoprotective and anti-tumor agents. In this research, we synthesized a set of novel cytokinin analogs with alkyl substituents at various positions of the aromatic moiety, as well as with oxygen-containing groups, and tested their antiproliferative activity in MDA-MB-231, A-375, and U-87 MG cell lines, and cytoprotective properties in H2O2 and CoCl2 models. Two amino-linked compounds were anti-proliferative with the ability to act synergistically with doxorubicin, and two carbamate-based ones were cytoprotective. According to the molecular docking data, anti-proliferation was based on the A2AR and APRT inhibition and cytoprotection on the CDK2 inhibition. The obtained results are promising for the development of novel anti-cancer therapeutics.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

There are numerous approaches to model an influence of manufacturing parameters on the dissolution and disintegration of solid dosage forms. A modern approach for modelling and simulating complex and heterogeneous systems such as pharmaceutical tablets focuses on computationally-intensive finite-element or discreet element methods. Industrial challenges such as Process Analytical Technology (PAT) and Quality by Design are stimulating computer-based technologies to design, control and improve the quality of pharmaceutical compacts and their performance. In this study the disintegration and dissolution model based on the numerical solutions of the Noyes-Whitney equation and cellular automata supported disintegration model are proposed and evaluated. The results from in vitro release studies of the mefenamic acid formulations were compared to the calculated release patterns from the tablet structures obtained from microtomography experiments and the purely algorithmically created virtual tablets.

Introduction: Despite the introduction of increasingly multifaceted diagnostic techniques and the general progress of emergency abdominal and vascular surgery, the outcome of treatment of patients with acute impaired intestinal circulation remains unsatisfactory. The non-invasive and high-resolution technique of optical coherence tomography (OCT) can be used intraoperatively to assess intestine viability and associated conditions that frequently emerge under conditions of impaired blood circulation. This study aims to demonstrate the effectiveness of multimodal (MM) OCT for intraoperative diagnostics of both the microstructure (cross-polarization OCT mode) and microcirculation (OCT angiography mode) of the small intestine wall in patients with acute mesenteric ischemia (AMI). Methods and Participants: A total of 18 patients were enrolled in the study. Nine of them suffered from AMI in segments II-III of the superior mesenteric artery (AMI group), where the ischemic segments of the intestine were examined. Nine others were operated for adenocarcinoma of the colon (control group), thus allowing areas of their normal small intestine to be examined for comparison. Data on the microstructure and microcirculation in the walls of the small intestine were obtained intraoperatively from the side of the serous membrane using the MM OCT system (IAP RAS, Russia) before bowel resection. The MM OCT data were compared with the results of histological examination. Results: The study finds that MM OCT visualized the damage to serosa, muscularis externa, and blood vessels localized in these layers in 100% of AMI cases. It also visualized the submucosa in 33.3% of AMI cases. The MM OCT image of non-ischemic (control group), viable ischemic and necrotic small intestines (AMI group) differed significantly across stratification of the distinguishable layers, the severity of intermuscular fluid accumulations and the type and density of the vasculature. Conclusion: The MM OCT diagnostic procedure optimally meets the requirements of emergency surgery. Data on the microstructure and microcirculation of the intestinal wall can be obtained simultaneously in real time without requiring contrast agent injections. The depth of visualization of the intestinal wall from the side of the serous membrane is sufficient to assess the volume of the affected tissues. However, the methodology for obtaining MM OCT data needs to be improved to minimize the motion artefacts generated in actual clinical conditions.

Cotton is the most ubiquitous and profitable fiber with diverse industrial and domestic applications. Grown in over 100 countries, it has a global market value of about $40 billion and employs over 350 million people from fields to textile mills, contributing about 7% of total labor-force recruitment in developing economies. Cotton has an indeterminate growth habit and an extensive tap root system affected by soil physicochemical and environmental conditions. There is a consensus among experts that conventional cotton cultivation still has a long way to attain sustainability, which is essential if cotton will maintain its competitive edge over other natural and synthetic fibers like hemp, polyesters, and rayon. Despite several efforts already committed to growing cotton sustainably, sustainability has eluded cotton cultivation globally because of the intense farm inputs (freshwater, pesticides, and heavy-duty equipment) needs, especially in developing economies. Some of the technological advancements towards achieving the goal of sustainable cotton cultivation include the development of new varieties, improved irrigation and mulching and precision agriculture techniques, application of remote sensing and Unmanned Aerial Systems (UAS) combined with image processing, and the introduction of autonomous and multi-purpose robotic platforms for growing and harvesting cotton. This review attempts to evaluate the successes already achieved by stakeholders in moving cotton towards sustainable production and identify areas where efforts are still needed to reach sustainable production and improved profitability goals for cotton with projections for future research directions.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

Ground penetrating radar (georadar, GPR), widely used in geology, archeology and road construction, is an efficient tool for searching and studying subsurface objects and structures. When planning GPR missions, it is necessary to predict the resolution of the device and the achievable probing depth. The article discusses the methods and results of assessing these characteristics of the Loza-V and Loza-N radars obtained in the course of archaeological and geographical expedition works.

Metastasis is the leading cause of cancer death and can be realized through the phenomenon of tumor cell fusion. The fusion of tumor cells with other tumor or normal cells leads to the appearance of tumor hybrid cells (THCs) exhibiting novel properties such as increased proliferation and migration, drug resistance, decreased apoptosis rate and avoiding immune surveillance. Experimental studies showed the association of THCs with a high frequency of cancer metastasis; however, the underlying mechanisms remain unclear. Many other questions also remain to be answered: the role of genetic alterations in tumor cell fusion, the molecular landscape of cells after fusion, the lifetime and fate of different THCs, and the specific markers of THCs, and their correlation with various cancers and clinicopathological parameters. In this review, we discuss the factors and potential mechanisms involved in the occurrence of THCs, the types of THCs, and their role in cancer drug resistance and metastasis, as well as potential therapeutic approaches for the prevention and targeting of tumor cell fusion. In conclusion, we emphasize the current knowledge gaps in the biology of THCs that should be addressed to develop highly effective therapeutics and strategies for metastasis suppression.

More than 20 years after the discovery of the first anelloviruses (AVs), they still remain a mysterious group of viruses. To date, there is no clear understanding of their impact on the host organism, although information is emerging about their participation in various pathologies. However, it is well known that AVs are an important component of the human virome. In the current study we assessed the abundance of AVs in viromes from four nasal and pharyngeal samples from children with respiratory symptoms using a metagenomic approach. It is worth noting that three patients had known respiratory viruses and one did not have any. Regarding AVs, they were detected in all samples, namely Torque teno mini virus (TTMV). The greatest abundance and diversity of AVs (Torque teno virus (TTV), TTMV and Torque teno midi virus (TTMDV)) were shown in a diseased patient with an absence of respiratory viruses, which may indicate the potential involvement of AVs in the maintenance of respiratory symptoms. An activated immune system to combat the main pathogens, against the background of which the number of AVs decreases, is discussed as a possible reason for the reduced diversity of anellome in other patients. We also compared the results of the metagenomic approach and qPCR for major respiratory viruses, which were in agreement. In addition, metagenomic sequencing made it possible to obtain additional data on viral genomes in order to establish their taxonomic identification and characterize individual viral profiles in patients from the Siberian part of Russia.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

The solid particle erosion at room and elevated temperatures of pure and filled hot-curing epoxy resin on anhydride hardener was experimentally tested using accelerated method on special bench. Micro-sized dispersed industrial wastes were used as fillers: fly-ash from a power plant and spent filling material from a copper mining and processing plant. The results showed that the unfilled resin wear significantly decreases with increasing temperature, while the dependence on the temperature of the wear intensity at an impingement angle of 45o is linear inversely proportional, and at an angle of 90o non-linear. The decrease in wear intensity is probably due to an increase in elasticity (an increase in the fracture strain limit) because of heating. Solid particle erosion of the examined filled epoxy compounds is considerably higher than that of unfilled compounds at impingement angles of 90o and 45o. Filled compounds showed ambiguous dependences of intensity of wear from temperature (especially at an angle of attack 45o), probably, character of dependence is defined by a filler share and the structural features of the samples caused by distribution of particles of the filler. Intensity of wear of the considered compounds at impingement angles 90o and 45o has high direct correlation with density and the modulus of elasticity (i.e., increases with their increase), and low correlation with bending strength of the considered materials. The data set for determining the correlation between mechanical properties and wear included characteristics due to both compound filling and test temperature.

This article investigates on the radial and non-radial geodesic structures of the generalized K-essence Vaidya spacetime. Within the framework of K-essence geometry, it is important to note that the metric does not possess conformal equivalence to the conventional gravitational metric. This study employs a non-canonical action of the Dirac-Born-Infeld kind. In this work, we categorize the generalized K-essence Vaidya mass function into two distinct forms. Both the forms of the mass functions have been extensively utilized to analyze the radial and non-radial time-like or null geodesics in great details inside the comoving plane. Indications of the existence of wormhole can be noted during the extreme phases of spacetime, particularly in relation to black holes and white holes, which resemble the Einstein-Rosen bridge. In addition, we have also detected the distinctive indication of the quantum tunneling phenomenon around the central singularity.

1,3 Dipolar cycloaddition of imidazolidine derivatives containing exocyclic double bonds is a convenient method of creating spiro-conjugated molecules with the promising anticancer active. In this work, the derivatives of parabanic acid (2-thioxoimidazolidine-4,5-diones and 5-aryliminoimidazolidine-2,4-diones) were firstly investigated as dipolarophiles in the reactions with nitrile imines. The generation of nitrile imines was carried out either by the addition of tertiary amine to hydrazonoyl chlorides «drop by drop» or using recently proposed diffusion mixing technique, which led to ~5-15% increasing of target compounds yields. It was found that the addition of nitrile imines to C=S or C=N exocyclic double bonds led to 1,2,4-thiazolines or triazolines and occurred regioselectively in accordance to the ratio of FMO coefficients of reactants. The yield of the resulting spiro-compound depended on the presence of alkyl substituents in nitrile imine structure and was significantly decreases at the reactions with imines with strong electron donor or electron-withdrawing groups. Some of the obtained compounds showed reasonable in vitro cytotoxicity. IC50 values were calculated for HCT116 (colon cancer) cells using the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) test.

The ability of S. aureus to infect humans and cause a wide range of infections so efficiently is a consequence of the many variant virulence factors that it can produce. Superantigens (SAgs) make up a group of them and include staphylococcal enterotoxins (SE). The main objective of this study was to detect enterotoxin gene cluster (EGC) in S. aureus isolates that caused infections in Paraguayan children in the year 2017, through an observational and cross-sectional study. The detection of the EGC including the seg, sei, sem, sen, seo, and seu genes, was carried out by end-point PCR. 181 S. aureus isolates were collected, most of them caused skin and soft tissue infections (SSTI, n=140, 77%) and came from children under 6 years 50% (n=90). At least one SE gene was detected in 96% (174/181) of isolates and 24% (44/181) carried the entire EGC. An association between methicillin resistance and seg, sei, seo, and seu gene carriage (p ≤0.05) was observed. A high prevalence of EGC was detected in S. aureus isolates collected from infected children attending the main health care centers in Paraguay, its importance is due to the potential of these toxins to aggravate staphylococcal infections.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

“De-[Constructing] Growth” is offered as a deeper and more useful conceptualization that avoids the negative connotations of, and resistance to, “degrowth” by decoupling profit from unsustainable consumption, production, and inequality.

The most effective method of treating allergic diseases, aimed not at relieving symptoms, but at eliminating the cause of the disease, is allergen-specific immunotherapy (AIT). To reduce the risk of side effects and improve the delivery of allergens to the mucosa, various delivery systems, such as liposomes, dendrimers, nanoparticles, etc., can be used. To date, there are data on the creation of delivery systems based on glycyrrhizic acid (GA) and its derivatives, but such a delivery system has not been used for allergen-specific therapy until now. At the same time, it is known that GA has an anti-inflammatory effect, shifts the balance towards Th1, and increases the number of Treg cells, which means that in the future it can enhance the anti-allergic effect of AIT and reduce the risk of unwanted side effects. Thus, the study of the immunomodulatory effect of supramolecular complexes (micelles) of GA with extracts of allergens seems to be very promising for the development of new drugs for AIT.

For the first time, an environmentally friendly waste-free closed cycle for the formation of EMI shielding materials that are promising for 5G communications is considered. Based on the proposed closed technological cycle, two types of EMI shielding materials have been obtained; both materials have significant prospects for signal shielding in all ranges that are allocated in different countries for 5G communication. The first type of materials are transparent conductive meshes with a transparency of more than 80% and with a shielding efficiency of more than 40 dB in the S and L bands and about 30 dB in the K and Ka bands. The study of signal reflection characteristics in the S, L, C, K and Ka bands showed the promise of using these materials as transparent 5G signal reflectors. The reflection coefficient in all considered ranges is above 90% (-0.5 dB). The second type of shielding material are continuous silver micro caps films characterized by a shielding efficiency of 90.1 dB at a thickness of 6.2±1.2 µm. We have also shown that silver micro caps can separate into silver flakes and ribbons when sonicated. These materials can also be used to produce EMI shielding coatings and composites. A detailed analysis of the shielding properties showed that each type of materials obtained in a closed technological cycle is comparable with the best literature results and significantly wins in terms of cost.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Measurements of temperature and salinity in the Amazon River plume in the open ocean of the western tropical North Atlantic are considered. The measurements were carried out using the AML CTD probe in the upper layer and a flow-through system that measures salinity and turbidity of seawater while the vessel is on the way. Additionally, archive oceanographic data from the WOD18 database, data of satellite altimetry measurements (AVISO), and satellite salinity data from Aquarius and SMOS were used. It is shown that the width of the Amazon plume is about 300–400 km, the depth of desalination is from 50 to 100 m. Surface salinity decreases compared to the background (36 PSU) by 0.5 PSU in February and more than by 3 PSU in September during the period of maximum development of the plume, which is determined from satellite measurements of surface salinity. Lagrangian modeling of the back-in-time advection of passive markers simulating freshwater particles was carried out. It was shown that the source of fresh water in the measurement area is the discharge of the Amazon.

Background: The practice of self-medication is common worldwide and is an important component of medical self-care. However, the practice can be dangerous and is linked to various risks for the patients and the entire community. This study aimed to estimate the prevalence and factors associated with self-medication among Bangladeshi adults. Methods: A cross-sectional survey was conducted between April and June 2021 among Bangladeshi adults (aged >19 years) using convenient sampling. A total of 1320 data were collected through face-to-face interviews using a standardized questionnaire. Multivariable logistic regression analysis was used to identify factors associated with self-medication practice (SMP). Results: Overall, 41% of adults in our survey reported SMP. The most common illnesses that prompted SMP were common cold/flu (66.4%), gastric problems (65%), and headache (64.4%). The most frequent reasons for SMP were to get better services (30.59%), perceive SMP without side effects (23.28%), and save time with effectiveness (14.56%). Potential risk factors included 10 years (AOR = 1.91; 95% CI: 1.04 - 3.50) and >12 years of schooling (AOR = 5.03; 95% CI: 2.27 - 11.15), being a businessman (AOR = 4.64; 95% CI: 1.74 - 12.37), having ≤6 family members (AOR = 2.13; 95% CI: 1.40 - 3.24), being a member of a social group (AOR = 1.53; 95% CI: 1.10 - 2.12), a health status check after every six months (AOR = 1.52; 95% CI: 1.08 - 2.13), and current ill-health (AOR = 1.41; 95% CI: 1.06 - 1.87). Protective factors identified included ≤30 years of age (AOR = 0.40; 95% CI: 0.17 - 0.93), and practice of modern (AOR = 0.39; 95% CI: 0.22- 0.69) and herbal (AOR = 0.45; 95% CI: 0.21- 0.97) healing types. Conclusion: More than one-third of the study participants reported practicing self-medication. Increasing the community’s awareness of the extreme consequences of SMP and not just the average experience might sway individuals away from SMP, and implementing strict jurisdiction could be a way to minimize the SMP.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

Biodiversity has become an issue of global anxiety over the past decades due to its rapid decline worldwide. Bangladesh as one of the most densely populated countries in the world is no more exception. The country, although, was once very rich in biodiversity, during the last few decades as a consequence of the rapid reduction in forest area, urbanisation, habitat modification, unsustainable natural resources use and collection and overall climate change it has decreased alarmingly. Of late, the government, as a signatory of various regional and international conservation treaties, has taken various initiatives to improve country’s dwindling biodiversity. This paper reviews the present situation of biodiversity in Bangladesh, management trends and major causes of biodiversity loss. A separate statutory body is fundamental to ensure conservation, sustainable use and equitable sharing of benefits arisen from biodiversity in the country.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Precise monitoring of individual crop growth and health status is crucial for precision agriculture practices. However, traditional manual inspection methods are time-consuming, labor-intensive, and often lack the spatial resolution required for detailed analysis. This research addresses the need for efficient and high-resolution crop monitoring by leveraging Unmanned Aerial Vehicle (UAV) imagery and advanced computational techniques. The primary objective was to develop a methodology for precise identification, extraction, and monitoring of individual corn crops throughout their growth cycle. This was achieved by integrating UAV-derived data with image processing, computational geometry, and machine learning techniques. UAV imagery was ac-quired bi-weekly at altitudes of 40m and 70m, capturing the entire growth cycle of a corn crop from planting to harvest. A time-series Canopy Height Model (CHM) was generated by analyzing the differences between the Digital Terrain Model (DTM) and the Digital Surface Model (DSM) derived from the UAV data. Local spatial analysis and image processing techniques were em-ployed to determine the local maximum height of each crop. Subsequently, a Voronoi data model was developed to delineate individual crop canopies, successfully identifying 13,000 out of 13,050 corn crops in the study area. For enhanced accuracy in canopy size delineation, vegetation indices were incorporated into the Voronoi model segmentation, refining the initial canopy area esti-mates by eliminating interference from soil and shadows. The proposed methodology enables precise estimation and monitoring of crop canopy size, height, biomass reduction, lodging, and stunted growth over time, providing valuable insights for precision agriculture practices. This work contributes to the scientific community by demonstrating the potential of integrating UAV technology, computational geometry, and machine learning for accurate and efficient crop mon-itoring at the individual plant level.

One of the drawbacks of natural fibers and their composites is their inherent hydrophilic nature. The effect of moisture on mechanical properties of a composite is irrefutable. This study deals with hygroscopic characteristics of Enset-PLA composites and its effect on the mechanical properties of the composite. To do this, injection molded composite specimens of different fiber volume fraction; plasticizer ratio, fiber length, and fiber age have been considered. The specimens are exposed to distilled water and the moisture absorption was monitored on a daily base. Subsequently, the specimens are subjected to mechanical loading to determine the effect of moisture on their Strength, Stiffness and strain at break strength. Lastly, individual and joint effects of considered factors have been scrutinized using optimal design of experiment. The result from the study shows that maximum and minimum moisture uptake is noticed for 25% and 10% fiber ratio respectively. Due to moisture effect, tensile and bending strength is decreased by 11% and 5% respectively for 15% fiber volume fraction; while 16% and 13% for 25% fiber volume fraction respectively. Increasing amount of plasticizer increases moisture resistance. The result indicate that Enset-PLA composite have competitive properties and stability when exposed to moisture.

In this study, we address the formidable challenge of solving large-scale Max-Cut problems (MCP). We introduce a rapid computational procedure utilizing a hybrid 1-flip/r-flip local search heuristic. This innovative strategy significantly reduces the computational time required for MCP problems while consistently generating solutions of exceptional quality. The paper presents substantial computational insights, showcasing the effectiveness of our approach on very-large-scale Max-Cut instances with varying densities. Our proposed heuristic is rigorously evaluated by comparing its performance against a quantum annealing solver, leveraging a multi-start Tabu Search framework. The results underscore the potency of this unique combination as an efficient and effective solution for large-scale QUBO problems. Notably, our hybrid heuristic consistently delivers high-quality solutions within the stringent CPU time limits of 600 seconds, demonstrating its efficacy across Max-Cut instances ranging from 10,000 to 40,000 variables. This research contributes to advancing the state-of-the-art in large-scale QUBO problem-solving, offering a powerful and time-efficient approach with broad applicability.

The major stress-inducible Hsp70 (HSPA1A) is overexpressed in the cytosol of many highly aggressive tumor cells including glioblastoma multiforme and presented on their plasma membrane. Depending on its intracellular or membrane localization, Hsp70 either promotes tumor growth or serves as a target for NK cells. The kinetics of the membrane Hsp70 (mHsp70) density on human glioma cells (U87) was studied after different irradiation doses to define the optimal therapeutic window for Hsp70-targeting NK cells. To maintain the cells in the exponential growth phase during a cultivation period of 7 days different initial cell counts were seeded. Although cytosolic Hsp70 levels remained unchanged on days 4 and 7 after a sublethal irradiation with 2 Gy, 4 Gy and 6 Gy, a dose of 2 Gy resulted in an upregulated mHsp70 density in U87 cells which peaks on day 4 and starts to decline on day 7. Higher radiation doses (4 Gy, 6 Gy) resulted in an earlier and more rapid onset of the mHsp70 expression on days 2 and 1, respectively, followed by a decline on day 5. Membrane Hsp70 levels are higher in G2/M than in G1, however, an irradiation-induced cell cycle arrest on days 4 and 7, was not associated with an increase in the mHsp70 density. Extracellular Hsp70 concentrations increased significantly compared to sham (0 Gy) irradiated cells on days 4 and 7 but not on day 1. Functionally, elevated mHsp70 densities were associated with a significantly better lysis by Hsp70-targeting NK cells. In summary, the kinetics of changes in the mHsp70 density upon irradiation on tumor cells is time- and dose-dependent.

This paper proposes two max-pooling engines, named the RTB-MAXP engine and the CMB-MAXP engine, with a scalable window size parameter for FPGA-based convolutional neural network (CNN) implementation. The max-pooling operation for the CNN can be decomposed into two stages, i.e., a horizontal axis max-pooling operation and a vertical axis max-pooling operation. These two one-dimensional max-pooling operations are performed by tracking the rank of the values within the window in the RTB-MAXP engine and cascading the maximum operations of the values in CMB-MAXP engine. Both the RBM-MAXP engine and the CMB-MAXP engine were implemented using VHSIC Hardware Description Language (VHDL) and verified by simulations. They have been employed for and tested in our CNN accelerator targeting at the CNN model YOLOv4-CSP-S-Leaky for object detection.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

We focus on macromolecules which are modelled as sequentially growing dual scale-free networks. The dual networks are built by replacing star-like units of the primal treelike scale-free networks through rings, which are then transformed in a small-world manner up to the complete graphs. In this respect, the parameter γ describing the degree distribution in the primal treelike scale-free networks regulates the size of the dual units. The transition towards the networks of complete graphs is controlled by the probability p of adding link between non-neighbouring nodes of the same initial ring. The relaxation dynamics of the polymer networks is studied in the framework of generalized Gaussian structures by using the full eigenvalue spectrum of the Laplacian matrix. The dynamical quantities on which we focus here are the averaged monomer displacement and the mechanical relaxation moduli. For several intermediate values of the parameter’s set (γ, p) we encounter for these dynamical properties regions of constant in-between slope.

A total of 473 metabolites were identified from 4 sour cherry genotypes using UPLC-TOF-MS. Untargeted metabolomics revealed the dominant chemical groups present in sour cherries. PCA showed that the diversity in sour-cherry metabolites was due to the genotype differences indicating iditol, malic acid, chlorobenzene, 2-mercaptobenzothiazole, and pyroglutamic acid as the predominant contributors. The variable importance in the projection (VIP > 1.0) in partial least-squares–discriminant analysis described 20 biomarker metabolites, representing the cherry metabolome profiles. A heatmap of Pearson’s correlation analysis between the 20 biomarker metabolites and antioxidant activities identified seven antioxidant determinants that displayed the highest correlations with different types of antioxidant activities. This study of correlating metabolomics and antioxidant activities elucidated that the higher nutritional value and biological functions of select sour cherry genotypes can be useful for the development of nutraceutical and functional foods.

Meningitis is a severe disease associated with death in children under five with highest rates of infections under age of one. Vaccines for Neisseria meningitides and Haemophilus influenza are used to prevent the main causative agents of meningitis. Administration of H. influenzae type b (Hib) vaccine is recommended at 2, 4 and 6 months with a booster dose at 18 months. N. meningitidis has two commercially available vaccines, the pure polysaccharide is recommended at 24 months meanwhile the protein-conjugated vaccines at 12 months. We sought in this study to examine if coadministering the vaccines for the two main meningitis causing bacteria might be synergistic as a preliminary step towards the possibility of shuffling immunization schedule. So, we coadministered Hib vaccine with commercially available vaccines either quadrate (ACWY) polysaccharide meningococcal (Men) or conjugated meningococcal (Nim) vaccines in Balb/C mice (n = 6/group) and compared to each vaccine administered separately and controls. Thirty-five days post immunization, we measured specific antibodies titers. Hib vaccine increased Men antibody titers significantly for serotypes Y and W. When Hib vaccine was coadministrated with Nim, antibody titer for Y, W and A significantly increased. For serotype C, there was no significant difference in antibody titers among immunized groups. As for effect of meningococcal vaccines on Hib, Men significantly increased Hib antibody titers while Nim had no effect. Collectively, our data suggested that coadministration of Hib and Men or Nim vaccines was safe and had synergistic effect on immune responses elicited to both vaccines. Further studies are needed before immunization schedule modifications. Such immunization schedule recommendation should provide better protection against this life-threatening disease in young children.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Wheat is widely grown in the Mediterranean region, where plants frequently face water shortages. Recently, more attention to rationalizing irrigation water has been increased due to the adoption of sustainable agricultural systems. Therefore, two field trials were conducted at the Agriculture Research Station of Nubaria, Egypt, in two consecutive seasons (2017/2018 and 2018/2019) to examine three irrigation regimes' effects, i.e., 60, 80, and 100% of crop evapotranspiration (ETc) combined with foliar ascorbic acid (AsA) or vitamin B2 (VB2) on yield and water productivity of wheat in two separate experiments. A split-plot design was used with three replicates. Irrigation treatments occupied the main plots, while the subplot in the first experiment was placed by ascorbic acid (AsA) and vitamin B2 in the second experiment. Results indicated that 100% ETc produced higher wheat yield and its attributes and insignificantly surpassed 80% ETc. Compared to the unsprayed plots, the foliar application of 6 mM ascorbic acid or 2.0 mM vitamin B2 significantly increased grain yield, components, and water use efficiency. The interaction between irrigation regimes (100% ETc or 80% ETc) and foliar application of 6.0 mM ascorbic acid or 2.0 mM vitamin B2 resulted in the highest values with no significant difference. Foliar application of ascorbic acid or vitamin B2 saved 20% of irrigation water while yielding a reduction that did not exceed 10%. The biplot graph of treatments x traits (TT) was a useful statistical tool for examining the impact of treatments on yield and its characteristics and identifying the links between these factors. Results suggest that riboflavin or ascorbic acid may have a potential role as an effective antioxidant for enhancing the tolerance for drought stress in wheat.

Tissue-like phantoms are widely used as a model for mimicking the optical properties of live tissue. This paper presents the results of a diffusion reflection method as well as fluorescence lifetime imaging microscopy measurements of fluorescein-conjugated gold nanorods in solution as well as inserted in solid tissue-imitating phantoms. A lack of consistency between the fluorescence lifetime results of the solutions and the phantoms raises a question about the ability of tissue-like phantoms to maintain the optical properties of inserted contrast agents.

The article is devoted to solving the problem of searching for universal explainable features that can remain explainable for a wide class of objects and phenomena and become an integral part of Explainable AI (XAI). The study is implemented on the example of an applied problem of early diagnostics of plant stress, using Thermal IR (TIR) and HSI, presented by 8 vegetation indices/channels. Each such index was presented by 5 statistical values. A Single-Layer-Perceptron classifier was used as the main instrument. TIR turned out to be the best of the indices in terms of efficiency in the field and sufficient to detect all 7 key days with 100% accuracy. Our study shows also that there are a number of indices, inluding NDVI, and usual color channels Red, Green, Blue, which are close to TIR possibilities in early plant stress detection with 100% accurasy or near, and can be used for wide class of plants and in different conditions their treatment. The stability of the stress classification in our study was maintained when the training set was reduced up to 10% of the dataset volume. The entropy-like feature of (max-min) for any indices/channels have determined as a leadersheep universal high-level explainable feature for the plant stress detection, which used in interaction with some of other statistical features.

This work is devoted to the study of the pyroelectric effect on the qualities of optical waveguides formed in a lithium niobate crystal by proton exchange. In the present work, we investigated the cessation effect of the radiation channeling during thermocycling of Y-splitters samples. We examined the spectral dependence of optical losses on a wavelength using an optical spectrum analyzer. The results demonstrate that in the range of 1530–1570 nm, all wavelengths are suppressed equally. The optical reflectometry method in the frequency domain shows that the increase of optical losses is observed along the entire waveguide, but not only at the Y-distribution point, as supposed earlier.

In 2023, the Bureau of Land Management (BLM) estimated that there were 68,928 mustangs living on United States public lands in 10 western states. The agency uses Appropriate Management Levels to determine the number of mustangs who need to be removed from the land. Once removed and processed, mustangs are sent to adoptions or sales events or retained in short-or long-term holding facilities. Adoptions and sales are the leading avenues for rehoming mustangs; however, the number of horses the BLM can place fluctuates annually and never approaches the greater number removed from the range. To explore opportunities for increasing the number of mustang adoptions, we conducted in-depth interviews with 23 horse trainers located on the U.S. East Coast, asking about participants’ training programs, relationships with horses, perceptions of mustangs, and challenges that mustangs face in the dressage and eventing industries. Participants had varying experiences with mustangs; however, all were willing to work with a mustang in some capacity. Participants voiced the need for more satellite adoption locations on the East Coast to decrease barriers to acquiring a mustang, notably cost and time, and for expanding existing training programs to include eventing and dressage.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

Annually, more than 1.5 million preventable new hepatitis B (HBV) infections continue to occur, with an estimated global burden of 296 million individuals living with chronic hepatitis B infection. This substantial health challenge results in over 820,000 annual deaths attributed to complications such as liver cirrhosis and hepatocellular carcinoma (HCC). HBV vaccination remains the cornerstone of public health policy to prevent chronic hepatitis B and its related complications. It serves as a crucial element in the global effort to eliminate HBV, as established by the World Health Organization (WHO), with an ambitious 90% vaccination target by 2030. However, reports on global birth dose coverage reveal substantial variability, with an overall coverage rate of only 46%. This comprehensive review thoroughly examines global trends in HBV vaccination coverage, investigating the profound impact of vaccination on HBV prevalence and its consequences across diverse populations, including both high-risk and general demographics. Additionally, the review addresses the formidable challenges and facilitating factors essential for achieving WHO's HBV vaccination coverage objectives and elimination strategies in the coming decade and beyond.

New antibiotics are unquestionably needed in the fight to the emergence and spread of multidrug-resistant bacteria. So far, antibiotics targeting bacterial central metabolism have been poorly investigated. By determining the minimal inhibitory concentration (MIC) of desmethylphosphinothricin (Glu-γ-PH), an analogue of glutamate with a phosphinic moiety re-placing the γ-carboxyl group, we previously showed its promising antibacterial activity on Escherichia coli. Herein we synthetized and determined the growth inhibition exerted on E. coli by an L-Leu dipeptide derivative of Glu-γ-PH (L-Leu-D,L-Glu-γ-PH). Furthermore, we compared the growth inhibition obtained with this dipeptide with that exerted by the free amino acid, i.e. Glu-γ-PH, and by their phosphonic and non-desmethylated analogues. All tested compounds were more effective when assayed in chemically defined minimal medium. The dipeptide L-Leu-D,L-Glu-γ-PH had a significantly improved antibacterial activity (2 μg/mL), at a concentra-tion between the non-desmethytaled (0.1 μg/mL) and the phosphonic (80 μg/mL) analogues. Also in Bacillus subtilis the dipeptide L-Leu-D,L-Glu-γ-PH displayed an activity comparable to that of the antibiotic amoxicillin. This work highlights the antibacterial relevance of the phosphinic pharmacophore and proposes new avenues to the development of novel antimicrobial drugs containing the phosphinic moiety.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p<0.001) and age at maternity discharge (p<0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

One of the key geophysical technologies for the energy industry during energy transition to zero footprint is fluid imaging. Knowledge of fluid distribution allows better, more optimized production reducing thus CO2 footprint per barrel produced and for CO2 storage the knowledge of where stored fluids go is mandatory to monitor reservoir seals. Electromagnetic is the preferred way to image fluid due to its strong coupling to the fluid resistivity. Unfortunately, acquiring and interpreting the data takes too long to contribute significantly to field operation and cost optimization. Using artificial intelligence and Cloud based data acquisition we can reduce the operational feedback to near real time and for the interpretation to close to 24 h. This then opens new door for the usefulness of this technology from exploration, monitoring and allows the application envelope to be enlarged to much noisier environment where real time acquisition can be optimized based on the acquired data.

This review focuses on the emerging evidence for the association between estimated cardiorespiratory fitness (eCRF) and metabolic risk factors. Given the challenges associated with directly measuring cardiorespiratory fitness (CRF) in large populations, eCRF presents a practical alternative for predicting metabolic health risks. A literature search identified six relevant cohort studies from 2021 to 2024 that investigated the association of eCRF with hypertension, hyperglycemia, dyslipidemia, and obesity. The review findings highlight a consistent inverse relationship between higher eCRF and lower incidence of metabolic risks in line with CRF cohort studies. This review highlights the importance of low eCRF as a primordial indicator for metabolic risks and underscores the need for broader application. Future research directions should include exploring eCRF's predictive accuracy across diverse populations and health outcomes and testing its real-world applicability in healthcare and public health settings.