Hydrogen has been considered a future energy carrier for decades and the demand for hydrogen in refineries is always upward due to the revival of new technologies. The steam methane reforming method is frequently employed because of its high hydrogen generation efficiency at a cheap cost and minimal negative impact on the environment. But depending on the type of feedstock, one unit of hydrogen generate 9-10 units of CO2 that is needed to be treated for environmental sustainability. Therefore, the optimization of hydrogen production and CO2 capture is very important to address. The simulation research was conducted to anticipate and optimize steam reforming using Aspen HYSYS. A conversion-type reactor was used to develop this simulation-based model. The primary goal of this work is to investigate and optimize the production efficiency of hydrogen and the mitigation of CO2 that is generated from the steam reforming process by varying process parameters. CO2 capture efficiency was investigated at the different yields for hydrogen production and was found that a maximum of 98.8% of the CO2 can be absorbed using the proposed carbon capture system. Later, the Aspen Energy Analyzer tool revealed potential improvements for energy and cost optimization.

White Spot Syndrome Virus (WSSV) has emerged as one of the most prevalent and lethal viruses globally, and infects both shrimps and crabs in the aquatic environment. This study aimed to investigate the occurrence of WSSV in different ghers of Bangladesh and the virulence of the circulating phylotypes. We collected 360 shrimp (Penaeus monodon) and 120 crab (Scylla sp.) samples from the South-East (Cox’s Bazar) and South-West (Satkhira) coastal regions of Bangladesh. The VP28 gene-specific PCR assays and sequencing revealed statistically significant (p < 0.05, Kruskal Wallis test) differences in the prevalence of WSSV in shrimps and crabs between the study areas (Cox’s Bazar and Satkhira), and over the study periods (2017-2019). The mean Log load of WSSV varied from 8.40 (Cox’s Bazar) to 10.48 (Satkhira) per gram of tissue. The mean values for salinity, dissolved oxygen, temperature and pH were 14.71±0.76 ppt, 3.7±0.1 ppm, 34.11±0.38˚C and 8.23±0.38, respectively in the WSSV-positive ghers. The VP28 gene-based phylogenetic analysis showed an amino-acid substitution (E→G) at 167th position in the isolates from Cox’s Bazar (referred to as phylotype BD2) compared to the globally circulating one (BD1). Shrimp PL artificially challenged with BD1 and BD2 phylotypes with filtrates of tissue containing 0.423 X 109 copies of WSSV per mL resulted a median LT50 value of 73 hrs and 75 hrs, respectively. The in-vivo trial showed higher mean Log WSSV copies (6.47±2.07 per mg tissue) in BD1 challenged shrimp PL compared to BD2 (4.75±0.35 per mg tissue). Crabs infected with BD1 and BD2 showed 100% mortality within 48 hrs and 62 hrs of challenge, respectively with mean Log WSSV copies of 12.06±0.48 and 9.95±0.37 per gram tissue, respectively. Moreover, shrimp antimicrobial peptides (AMPs) penaeidin and lysozyme expression was lower in BD1 challenged group compared to BD2 challenged shrimps. These results collectively demonstrated that relative virulence properties of WSSV based on mortality rate, viral load and expression of host immune genes in artificially infected shrimp PL could be affected by single aa substitution in VP28.

With increasing interest in understanding contribution of secondary organic aerosol (SOA) to particulate air pollution in urban areas, an exploratory study was carried out to determine levels of carbonaceous aerosols and polycyclic aromatic hydrocarbons (PAHs) in the City of Kuala Lumpur, Malaysia. PM2.5 samples were collected using a high-volume sampler for 24 h in several areas in Kuala Lumpur during the north-easterly monsoon from January to March 2019. Samples were analysed for water soluble organic carbon (WSOC), organic carbon (OC), elemental carbon (EC) and secondary organic carbon (SOC) in PM2.5 was estimated. Particle-bound PAHs were analysed using gas chromatography-flame ionization detector (GC-FID). Average concentrations of WSOC, OC and EC were 2.7 ± 2.2 (range of 0.63-9.1) µg/m3, 6.9 ± 4.9 (3.1-24.1) µg/m3 and 3.7 ± 1.6 (1.3-6.8) µg/m3, respectively, with estimated average SOC of 2.3 µg/m3, contributing 34% to total OC. The average of total PAHs was 1.8 ± 2.7 ng/m3. Source identification methods revealed natural gas and biomass burning, and urban traffic combustion as dominant sources of PAHs in Kuala Lumpur. To understand human health risk posed by PAHs, a deterministic screening health risk assessment was also conducted for several age groups including infant, toddler, children, adolescent and adult. The total concentration of BaPeq is 3.8 ng/m3, with the average of 0.29 (range of 0.001-1.6) ng/m3. Carcinogenic and non-carcinogenic risk of PAH species were well below the acceptable levels recommended by the USEPA. Future work is needed using long-term monitoring data to understand the origin of PAH contributing to SOA formation and to apply source-risk apportionment to know better the potential risk factors posed by the various sources in urban areas in Kuala Lumpur.

Plants and plant-derived food products have been used for medicinal purposes since the ancient. Medicinal Plant-based functional foods or plant-based dietary compounds are a re-emerged interest for their therapeutic benefits and nutritive supports which has implicated in healthcare systems across the world. Neurological disorders are one of the greatest threats to public health and according to the World Health Organization, about 100 million people are affected globally by several neurological and mental ailments. In a traditional medication system, medicinal plants have been applied as both neuro-therapeutic purposes and micro-macro nutrients provider for the wellbeing of psychological states e.g. anti-depressant, anti-anxiety, anti-convulsions, anti-dementia, anti-psychotic, etc. Herein, it is a topic of great interest to present a conceptual aspect by reviewing relevant scientific literature about the plant-based functional foods or bioactive phytochemicals for the prevention and treatment of mental and neurological disorders. From the literature assessment, we have found that nutritional neuroscience is becoming an advanced research discipline and there has been a growing pile of evidence concerning the therapeutic use of plant-based functional foods and/or plant-derived food compounds for the management of neurologic health, evolving with promising impact over the time.

The present study was carried out at the north-eastern part of Bangladesh to investigate organochlorine pesticide (OCP) residues and microbiological quality of dried barb (Puntius sophore). Samples were collected from both producers and retailers from December 2016 to April 2017. A control sample was also prepared with the same raw fish used by the producers in the laboratory to compare the result. Gas Chromatography with Electron Capture Detector (GC-ECD) was used to detect and quantify OCP residues. Around 22 % (6) samples out of 27 were found contaminated with OCP residues. Among these six adulterated samples, four were from retailers and two from producers. Only Aldrin was detected in four samples and rest two samples were detected with both Aldrin + Dieldrin and Aldrin + Endrin. Aldrin was found between 0.332 to 0.967 ppm, Dieldrin 0.762 ppm, and Endrin 0.828 ppm. All these values were much higher than the Maximum Residual Limit (MRL) 0.1 ppm. Aerobic Plate Count (APC) of producer samples were ranged between log5.3 ± 0.02 to log5.4 ± 0.03, log6.2 ± 0.02 to log6.4 ± 0.02 for retailer samples and log5.0 ± 0.03 to log5.2 ± 0.04 for control samples. While fungal count was ranged between log3.2 ± 0.04 to log3.5 ± 0.04, log3.4 ± 0.04 to log3.6 ± 0.03 and log2.2 ± 0.05 to log2.5 ± 0.03 for producer, retailer and control samples respectively. All the producer and retailer samples and one-third of the control samples were found contaminated with Escherichia coli. Whereas, Salmonella sp. was detected as 13.3% in producer samples, 20% in retailer samples except for the control. In case of Vibrio sp., maximum count was found for retailer samples (13.3%), whereas, producer and control samples showed no detection. The finding of the present study revealed the presence of pesticides and poor microbiological quality of dried barb are alarming for the consumers of Bangladesh and which may cause chronic disease and potential long-term risk for human health.

Cantilever beams are the most widely used form of strain-driven energy harvesting, which uses piezoelectric materials. Although researchers are constantly seeking improved power output from cantilever-beam-driven piezoelectric energy harvesters, a systematic and fundamental analysis of the effect of beam geometry on the power capacity of energy harvesters warrants further investigation. Most of the previous research accounts for beams that are fully coated with piezoelectric material. While a larger coating area increases energy output, it also escalates costs as piezoelectric materials are very expensive. Considering the high cost of piezoelectric materials when dealing with limited piezoelectric material, enhancing power output can be achieved by employing a larger base beam and coating a portion of it at the fixed end. As such, the aim of this work is to investigate a wide variety of cantilever beam shapes (e.g., trapezoidal, triangular, V-cut, concave, and convex) with partial piezoelectric material coating on the base beam to maximize the power output capacity of the harvester. To ascertain a comparable argument, the surface area, volume, and mass of all the considered beam shapes are kept consistent, as these parameters influence the power output of the harvester. The geometry of each shape is systematically varied to understand the effect of geometric configuration on the output power density. Finally, the power capacities of all types of beams are compared, and a design is proposed to obtain the maximum power output. It was found that when the surface area of both the beam and piezoelectric material is kept constant and piezoelectric material is located at the fixed end, a trapezoidal beam with a smaller base width and larger free end width is the most efficient in generating power as long as the structural integrity is maintained. The finding is completely opposite as was suggested by previous studies, which proposed that a trapezoidal beam with a smaller free end yields higher output. Instead, this study demonstrates that an inverted trapezoidal beam produced higher output, considering partial coating compared to the full beam coating used in previous studies. Additionally, a correlation is presented on how the beam resonance frequency shifts with variation in beam parameters.

Background: Physical activity (PA) has paramount importance for achieving good health and an active lifestyle among university students. Quality physical education (QPE) program ensures the attainment of sustainability in PA. Motivation can be considered a critical factor in promoting PA in students. However, motivation alone cannot bring inclusivity unless quality aspects are not being incorporated thoughtfully into physical education (PE) programs. Aims: As such this study aimed at examining three research questions: i) do the motive of PA participation can be enhanced through the quality provision of PE programs in university settings ii) does the quality provision of PE help promote sustainable PA among adolescents? and iii) whether or not this carry-over process is influenced by gender. Methods: This cross-sectional study recruited N = 610 (male = 467) & female = 143) university students. Students who studied PE as one of their course subjects were only included in this study. They participated in > 27 different sports and had a mean age of 20.76 (SD = 3.47) years and a mean of 4.70 (SD = 4.93) years of athletic experience. Descriptive (mean, SD) statistics, Pearson’s correlation, and regression analysis were used to meet the objectives. To examine the variables’ differences in gender, data were then computed using a 2 (Gender) by 2 (Type of Sport: Individual vs. Team) MANCOVA, with the covariate being age. Results: The factors provided sound reliability scores and highlighted positive correlations between QPE and exercise needs satisfaction. However, the factors lacked establishing correlations with PA. The perceived competence for exercise needs satisfaction reported differences in sexes, with the male being scored higher. Furthermore, QPE did not show any significant differences in gender. In comparison to females, males showed higher mean scores in the PA. Conclusion: The provision of QPE is identified as a pivotal factor in determining the competence of exercise satisfaction among students. QPE provision was adequate in the university, however, it could not promote PA among females as expected.

The abrupt increase of the electric vehicles in Bangladesh needs huge amount of power. As a result, alternative energy sources are emphasized due to limited fossil fuels in order to develop a sustainable energy sector with environment friendly resources. Bangladesh has an enormous potential in the field of renewable resources like biogas and biomass. This paper presents 20 kW electric vehicle charging station (EVCS) utilizing biogas resources where maximum energy requirement is 100 kWh. In this paper, the biogas based EVCS is designed using MATLAB Simulink and HOMER software. Daily 15-20 electric vehicles can be recharged their batteries using the proposed charging station. The proposed system offers lower cost of energy compared to the grid electricity. Moreover, the proposed charging station shows 68.75% reduction in CO₂ emission than grid based charging station. In addition, the proposed EVCS will save monthly $ 16.25 and $ 27.50 respectively for easy bike and auto rickshaw type electric vehicles in Bangladesh.

Climate change is one of the most concerning global issues and has the potential to influence every aspect of human life. Like different components of society, it can impose significant adverse impacts on pavement infrastructure. Although several research efforts have focused on studying the effects of climate change on natural and built systems, its impact on pavement performance has not been studied extensively. Due to the weather effect the lifetime of pavement is getting lower on the other hand maintenance cost is getting higher and higher. The data has been collected from LTTP website and as a site The State of Texas has been considered. The primary objective of this project is to quantify the effect of temperature as well as precipitation changes on pavement response and performance prediction using the ARIMA model and develop a logistic regression model to analyze the forecast data.

The Internet of Things (IoT) is still a relatively new field of research, and its potential for use in the healthcare and medical sectors is enormous. In the last five years, IoT has been a go-to option for various applications such as using sensors for different features, machine-to-machine communication, etc., but precisely, in the medical sector, it is still lagging far behind compared to other sectors. Hence, this study emphasizes the IoT applications in medical fields, Medical IoT sensors and devices, IoT platforms for data visualization, and artificial intelligence in medical applica-tions. A systematic review considering PRISMA guidelines on research articles as well as the websites on IoMT sensors and devices have been carried out. A total of 986 articles after the year 2001 have been initially selected, and by applying the inclusion-exclusion criterion, a total of 597 articles have been identified. From these, 23 studies have been finally selected for this systematic review. This review analyzes different sensor monitoring circuits in detail, considering an Inten-sive Care Unit (ICU) scenario, device applications, and the data management system, including IoT platforms for the patients. Lastly, detailed discussion and challenges have been outlined, and possible prospects have been presented.

COVID-19 vaccine hesitancy is considered responsible for the lower rate of acceptance of vaccines in many parts of the world. However, sources of this hesitancy are rooted in many social, political, and economic factors. This paper strives to find the most important variables in predicting the COVID-19 vaccination uptake. We introduce an explainable machine learning (ML) framework to understand the COVID-19 vaccination uptake around the world. To predict vaccination uptake, we have trained a random forest (RF) regression model using a number of sociodemographic and socioeconomic data. The traditional decision tree (DT) regression model is also implemented as the baseline model. We found that the RF model performed better than the DT model since RF is more robust to handle nonlinearity and multi-collinearity. Also, we have presented feature importance based on impurity measure, permutation, and Shapley values to provide the most significant unbiased features. It is found that electrification coverage and Gross Domestic Product are the strongest predictors for higher vaccination uptake, whereas the Fragile state index (FI) contributed to lower vaccination uptake. These findings suggest addressing issues that are found responsible for lower vaccination uptake to combat any future public health crisis.

{\bf Abstract.} \\ {\bf Background:} Bangladesh hosts more than 800,000 Rohingya refugees from Myanmar. The low health immunity, lifestyle, access to good healthcare services, social-security cause this population to be at risk of far more direct effects of COVID-19 than the host population. Therefore, evidence-based forecasting of the COVID-19 burden is vital in this regard. In this study, we aimed to forecast the COVID-19 burden among the Rohingya refugees of Bangladesh to keep up with the disease outbreak's pace, health needs, and disaster preparedness. \noindent{\bf Methodology and Findings:} To estimate the possible consequences of COVID-19 in the Rohingya camps of Bangladesh, we used a modified Susceptible-Exposed-Infectious Recovered (SEIR) transmission model. All the values of different parameters used in this model were from the Bangladesh Government’s database and the relevant emerging literature. We addressed two different scenarios, i.e., the best-fitting model and good fitting model with unique consequences of COVID-19. Our best fitting model suggests that there will be good control over the transmission of the COVID-19 disease. At the end of December 2020, there will be only 169 confirmed COVID-19 cases in the Rohingya refugee camps. The average basic reproduction number ($ \mathcal{R}_{0} $) has been estimated to be 0.7563. \noindent{\bf Conclusion:} Our analysis suggests that, due to the extensive precautions from the Bangladesh government as well as other humanitarian organizations, the coronavirus disease will be under control if the maintenance continues like this. Although detailed and pragmatic preparedness should be adopted for the worst scenario.

The study tries to find out the impact of investors demographic variables on the return from the stock market. The data has been collected from the brokerage and Marchant banks for individual investors investments, return and demographic characteristics. The research covers the period from 2009 to 2021 and have a decade long enough to identify the trend. The structural break in the data also been adjusted to avoid any kind of endogeneity. The regression results suggest that demographic variables affect the investment pattern and beta return for the investors. the demographic variables such as education, location and experience have positive links with the beta whereas age and income show negative association. The education, income and experience variables are also found to be significant in the empirical analysis.

Mangrove vegetation plays a vital role in habitat and nursing ground for different organisms and prevents coastal erosion caused by wave and tide action. In recent years the mangrove vegetation in Chattogram coast, Bangladesh, has been interrupted by other infrastructural development, which has a destructing effect on the surrounding environment. Land surface temperature analysis of an area helps learn about different environmental conditions, weather, and climate. It is also essential to monitor the rising temperature and global warming, the biggest threat to humanity. NDBI and NDVI are the efficient process for monitoring vegetation and build up areas of a geographical location. This study focused on those analyses to understand the importance of mangrove vegetation in the Salimpur area and surrounding coastal areas of Chattogram by studying the relationship between NDVI and NDBI, NDVI and LST, NDBI, and LST. The outcome indicates that a higher vegetation index results in lower land surface temperature during different periods, negatively correlated. This study also found a strong positive correlation between buildup index (NDBI) and land surface temperature (LST), which means Land Surface temperature was found higher in Buildup areas. The vegetation areas are greatly affected by the buildup areas. The correlation between buildup areas and vegetation areas was strongly negative, which means an increase of NDBI decreases NDVI, and a decrease of NDBI increases NDVI.

AbstractTo overcome the negative impacts on the environment and other problems associated with fossil fuels have forced many countries to inquire into and change to environmentally friendly alternatives that are renewable to sustain the increasing energy demand. Solar energy is one of the best renewable energy sources with the least negative impacts on the environment. Different countries have formulated solar energy policies to reduce dependence on fossil fuel and increasing domestic energy production by solar energy. According to the 2010 BP Statistical Energy Survey, the world cumulative installed solar energy capacity was 22928.9 MW in 2009, a change of 46.9% compared to 2008. In this study, a PV generation system has been modeled and installed considering uncertain whether based on the hourly wind speed data of New York City (NYC) of year 2014. Regression models has been used to forecast the hourly, weekly, and monthly wind speed of NYC year 2014. Design of experiment (DOE) has been used to determine the optimal panel size (area), the battery capacity size, and other levels of factors.

Fault detection is an important step for subsurface interpretation and reservoir characterization from 3D seismic images. Due to the numerous and complicated faulting structures of seismic images, manual seismic interpretation is time taking and need intensive work. To overcome this problem, geoscientists are coming up with productive computer-aided techniques for assisting in interpreter science for many years. However, in this paper, we used a pre-trained CNN model to predict faults from the 3D seismic volume of the Poseidon field of Browse Basin, Australia. Basically, this field is highly structured with complex normal faulting throughout the targeted Plover Formations. So, our motivation for this work in this field is to compare machine learning-based fault prediction to user interpreted faults identification with supported by seismic variance attribute. We found very satisfying result using DL with having an improved fault probability volume that outperform variance technology. Therefore, we propose that this workflow could reduce time and able to predict fault quite accurately in any field area.

Recently, the Third Generation Partnership Project (3GPP) introduced the New Radio (NR) technology for Vehicle-to-everything (V2X) communication to enable delay-sensitive and bandwidth-hungry applications in vehicular communication. The NR system is strategically crafted to complement the existing Long Term Evolution (LTE) Cellular-Vehicle-to-Everything (C-V2X) infrastructure, particularly to support advanced services such as the operation of automated vehicles. It is widely anticipated that the 5th generation (5G) NR system will surpass LTE C-V2X in terms of achieving superior performance in scenarios characterized by high throughput, low latency, and enhanced reliability, especially in the context of congested traffic conditions and a diverse range of vehicular applications. This article will provide a comprehensive literature review on vehicular communications from Dedicated Short Range Communication (DSRC) to NR V2X. Subsequently, it delves into a detailed examination of the challenges and opportunities inherent in NR V2X technology. Finally, we proceed to elucidate the process of creating and analyzing an open-source 5G NR V2X module in network simulation-3 (ns-3) and then demonstrate the NR V2X performance in terms of different key performance indicators implemented through diverse operational scenarios.

Despite being considered as natural components of many ecosystems, forest fires pose significant threats to the environment and human health. In order to ensure public safety and effective fire suppression planning, it is necessary to develop reliable prediction models to mitigate forest fire danger. These models should account for specific environmental conditions. The advent of big data in recent years has opened new avenues for improving forest fire predictions. Machine learning techniques, surpassing traditional forecasting methods, have shown significant promise in this area. By applying the Cross-Industry Standard Process for Data Mining (CRISP-DM) methodology to a real-world dataset, this paper explores the application of machine learning approaches to understand forest fire patterns and predict fire danger. We consider six distinct time stages and incorporate feature selection to refine our predictions. It is important to note that forest fire behavior models are not universally effective due to geographical variations in data. Nevertheless, advanced decision-making techniques are vital in forest fire management. Our research presents a systematic exploration of the topic, comparing various machine learning models, thereby providing a comprehensive baseline for future investigations in this crucial environmental arena.

Abstract Background COVID-19 vaccination program among Adults in India is one of the highly successful vaccination drives globally. Indian children aged 15–18 years old became eligible for COVID-19 vaccination on 3rd January, 2022 followed by 12-14 years old children on 16th March, 2022. As parents are primary decision-makers for their children, we aimed to assess parents' perceptions and intentions regarding COVID-19 vaccination for children in India. Aim To assess parental perceptions and intention to get COVID-19 vaccination for their children (aged<18 years), Materials and Methods A cross-sectional anonymous web-based survey was designed. Healthcare workers of a tertiary care institute in Eastern U.P. having any children aged <18 years were the study population. They were recruited through snowball sampling and were sent the study questionnaire in Google form through email and WhatsApp. Cross-tabulation was performed by parents' intention to vaccinate their children against COVID-19 virus with socio-demographic characteristics and their risk perception toward COVID-19, trust in the healthcare system, and their history of vaccine hesitancy behavior routine childhood immunization. Bi-variate analysis was performed to find out the predictors of child vaccination intention among the parents. Results A total of 388 healthcare workers parents (HCWPs) having A child < 18 years of age completed the survey. Mean age of the parents were 40.28 ±11.34 years with majority(97.0%) completing recommended 2 doses of COVIID-19 vaccine. Around 91% of the parents agreed that COVID-19 vaccines are important for child’s health whereas about 89% agreed to the statement that COVID-19 vaccines are effective. A total 356 (91.7%) participants were willing to vaccinate their child against COVID-19, 91.3% of them liked to do so as soon as possible. The factors significantly associated with the stated likelihood of child vaccination among the participants were younger age, female gender, urban residence, absence of any chronic illness, lower monthly income, history of COVID-19 in child and the child/children completed with routine childhood vaccines. Parental concerns mainly centered around vaccine need, safety and side effects. Conclusion The healthcare worker parents(HCWPs) have good knowledge and positive attitude towards COVID-19 vaccination for children. Around 92% of them were willing to vaccinate their children with COVID vaccine currently, which implies very low vaccine hesitancy among the HCWPs . Further longitudinal studies are required to be conducted to assess the trend of parental acceptance of COVID vaccine.

The COVID-19 epidemic and the measures adopted to contain it have had a significant impact on energy patterns throughout the world. The pandemic and movement restrictions led to unpredictable fluctuations in power systems demand and the fuel price for a delayed period. Monkeypox, another viral disease, appeared during the post-COVID period. It is assumed that the outbreak of monkeypox is unlikely due to the implication of preventive measures experienced by COVID-19. At the same time, the probability of an epidemic cannot be blindly overlooked. This paper aims to examine and analyze historical data to look at how much petroleum fuel was used for generating power and how the price of petroleum fuel changed over seven years, from January 2016 to August 2022. This period covers the time before the COVID-19 pandemic, during the pandemic, and after the pandemic. Several time-series forecasting models, including all four benchmark methods (Mean, Naïve, Drift, and Snaïve), Seasonal and Trend decomposition using Loess (STL), Exponential Smoothing (ETS), and Autoregressive Integrated Moving Average (ARIMA) methods have been applied for both fuel consumption and price prediction. The best forecasting method for fuel price and consumption has been identified among these methods. The paper also utilizes the ARIMAX model by incorporating multiple exogenous variables, such as monthly mean temperature, mean fuel price, and mileage of vehicles traveling during a certain period of pandemic lock-down. It will assist in capturing the non-smooth and stochastic pattern of fuel consumption and price due to the pandemic by separating the seasonal influence and thus provide a prediction of the consumption pattern in the event of any future pandemic.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

Building Information Modelling (BIM) has been more popular in the construction industry as a consequence of the many advantages it offers, such as increased productivity, improved project outcomes, and reduced expenses. However, there are many obstacles that must be overcome before BIM can be widely used. This research uses a poll of construction industry experts to investigate the challenges associated with using BIM in projects. Cost of implementation, inadequate standards and procedures, and a lack of knowledge with BIM were some of the hurdles that were measured in the study. Statistical techniques were used to examine the data, and the findings indicate that the high cost of implementation and the absence of sufficient standards and procedures are the two main obstacles to the widespread adoption of BIM. Problems with supply chain management and a lack of experience with BIM are also mentioned as obstacles. The report also suggests solutions, such as a more focused teaching effort on BIM-related issues and the creation of a specialised BIM curriculum. Professionals in the construction industry may utilise the study’s results to their advantage by expanding their knowledge of the obstacles standing in the way of widespread adoption of BIM.

The reuse of recycled crushed concrete aggregate (RCCA) and reclaimed asphalt pavement (RAP) can provide a sustainable solution for the disposal of C&amp;D materials instead of sending it to landfill. More importantly, it will save energy and reduce impact on the environment. Several states in USA are using RCCA and RAP as base materials for years, focusing on the quality of the recycled materials. The structure of Recycled Aggregate (RA) is more complex than Natural Aggregate (NA). RAs have old mortar adhered on them that forms a porous surface at interfacial transition Zone (ITZ) and prevents new cement mix from bonding strongly with the aggregates. The objective of this work was to correlate microstructural properties like micro-porosity, inter and intra aggregate pores with the unconfined compressive strength (UCS) of RAP and RCCA molds, mixed at different proportions. In this paper, the quantity of micro-pores and their effect on the strength of mixed materials is used as the basis of microstructural analysis of recycled concrete and reclaimed asphalt. Microstructural properties obtained from the analysis of scanning electron microscope (SEM) images were correlated with unconfined compressive strength. Intra-aggregate and inter-aggregate pores were studied for different ratios of cement treated mixture of RAP and RCCA. The results show that the number of pores in the mixture increases considerably by adding RAP, which eventually causes reduction in unconfined compressive strength. In addition, significant morphological and textural changes of recycled aggregates were observed by SEM image analysis.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

Background: Currently, limited number of therapeutic options are available to treat Diabetes mellitus, and to find a potential candidate, laboratory work takes time and also needs animal studies. So, the aim of this study was to determine the efficacy of some natural phytocompounds with the aid of molecular docking, bioinformatics and in silico drug design approaches. Method: Two proteins (Human CYP3A4 linked to metformin and Human dipeptidyl peptidase-IV) were selected and molecular docking studies were conducted using Pymol, AutoDock Vina, PyRx, and Discovery Studio. Different important pharmacokinetic parameters like ADME and toxicity data were obtained from online databases SwissADME and pkCSM program. Results: It was found that human dipeptidyl peptidase-IV (PDB ID: 4A5S) has exhibited a maximal affinity of -9.7 Kcal/mol for bryonolic acid and hesperidin, but only -6.7 kcal/mol for metformin hydrochloride. Similarly, the highest affinity of hesperidin for human CYP3A4 bound to metformin (PDB ID: 5G5J) is -10.7 Kcal/mol compared to metformin hydrochlor (-6.3 Kcal/mol). Besides, all the compounds have been documented outstanding ADMET profile, and accepted by drug-likeness or Lipinski rule. Conclusions: The present study suggested that these compounds can be further investigated in vitro and in vivo to establish them as lead compounds against Diabetes mellitus..

Global warming has been increasing heat stress threat in animals which can be monitored by Temperature Humidity Index (THI). The present study describes the relationship of THI, calculated using 35 years period weather station data, and production performances of dairy cattle in a se-lected area of Bangladesh. The month January and June were identified as the coolest and hottest, respectively. Based on this outcome, every year in the month of January and June production performances of 10 crossbred cows with homogenous characteristics were monitored for a period of 5 years. The average THIMEAN value was found 17% higher in June as compared to January, and with this increment of THIMEAN average milk production was decreased 24.4% (p<0.05). The milk fat and protein content were also reduced (p<0.05) by 14.5 and 15.2%, respectively suggesting negative correlation as like as milk production. However, ash content was increased 15.3% that indicates a positive correlation. In addition, multiple regression analysis revealed each point increase in THIMEAN and rectal temperature, there was a decrease in milk yield 0.04 and 1.17 kg ECM, respectively. In contrary, each point increase in THIMEAN resulted 0.059 C increase of rectal temperature. Taken together, THIMEAN value calculated using metrological station data has distinct relationship with the production performances of lactating crossbred dairy cows.

The main goal of this article is to demonstrate the impact of environmental data on the spreading of Covid-19. In this research, data has been collected from 70 cities/provinces that are affected by Covid-19. Here, environmental data refers to temperatures, humidity and population density in each of these cities/provinces. This data has been analyzed using statistical models such as Poisson, Quasi-Poisson and negative Binomial. It is found that a negative Binomial regression model is the best fit for our data. Our results reveal that average high temperature is the vital factor to slow down the spread of Covid-19. In addition, higher population density found to be an important factor for the quick spreading of Covid-19 where it is quite impossible to maintain the social distance and the virus can spread easily.

Purpose: To evaluate the efficacy and survival rates of same session ab interno trabeculectomy with the trabectome and Ahmed glaucoma valve implant (AT) in comparison to the Ahmed glaucoma valve alone (A). Method: A total of 107 eyes undergoing primary glaucoma surgery were enrolled in this retrospective comparative case series, including 48 eyes which underwent AT and 59 eyes which received A alone. Participants were identified using the procedural terminology codes, and their medical records were reviewed. The primary outcome measure was surgical success, defined as intraocular pressure (IOP) > 5 mmHg, ≤ 21 mmHg, and IOP reduction ≥ 20% from baseline at two consecutive visits after three months, no reoperation for glaucoma. Secondary outcome measures were IOP, the number of glaucoma medications, incidence of a hypertensive phase, and best corrected visual acuity (BCVA). Results: The cumulative probability of success at one year was 70% in AT, and 65% in A (p=0.85). IOP decreased significantly from 26.6 ± 10.1 mmHg at baseline to 14.7 ± 3.3 mmHg at the final follow-up in AT (p= 0.001). The corresponding numbers for A were 28.8 ± 10.2 and 16.7 ± 4.9, respectively (p= 0.001). The final IOP was significantly lower in AT (p= 0.022). The number of medications at baseline was comparable in both groups (2.6 ± 1.2 in AT and 2.5 ± 1.3 in A, p=0.851). Corresponding number at 1 year visit was 1.2±2 in AT and 2.8±1.8 in A (p=0.001). The incidence of a hypertensive phase was 18.7% in AT and 35.5% in A (p=0.05). HP resolved in only 30% of eyes. The criteria for HP resolution were fulfilled in 9 eyes (30%). There was no difference in the rate of resolution of the hypertensive phase between AT and A (33.3% and 28.5%, respectively, p=0.67). Conclusion: Ahmed glaucoma valve implant with same session trabectome surgery significantly decreased the rate of the hypertensive phase and postoperative IOP as well as the number of glaucoma medications.

The U.S. Energy Information Administration (EIA) provides crucial data on monthly and annual fuel consumption for electricity generation. This data covers significant fuels such as coal, petroleum liquids, petroleum coke, and natural gas. Fuel consumption patterns are highly dynamic, influenced by diverse factors. Understanding these fluctuations is essential for effective energy planning and decision-making. This study outlines a comprehensive analysis of fuel consumption trends in electricity generation. Utilizing advanced statistical methods, including time series analysis and autocorrelation, our objective is to uncover intricate patterns and dependencies within the data. This paper aims to forecast fuel consumption trend for electricity generation using data from 2015 to 2022. Several time-series forecasting models, including all four benchmark methods (Mean, Naïve, Drift, and seasonal Naïve), Seasonal and Trend Decomposition using Loess (STL), Exponential Smoothing (ETS), and Autoregressive Integrated Moving Average (ARIMA) methods, have been applied. The best-performing models are determined based on Root Mean Squared Error (RMSE) values. For Natural Gas (NG) consumption, the ETS model achieves the lowest RMSE of 20,687.46. STL demonstrates the best performance for coal consumption with an RMSE of 5,936.203. The seasonal Naïve (SNaïve) model outperforms others for petroleum coke forecasting, yielding an RMSE of 99.49. Surprisingly, the Mean method has the lowest RMSE of 287.34 for petroleum liquids, but the ARIMA model is reliable for its ability to capture complex patterns. Residual plots are analyzed to assess the models' performance against statistical parameters. Accurate fuel consumption forecasting is very important for effective energy planning and policymaking. The findings from the study help policymakers strategically allocate resources, plan infrastructure development and support economic growth.

Diabetes is one of the fatal diseases that play a vital role in the growth of other diseases in the human body. Controlling and curing diabetes in its early stages is the most significant technique to avoid its effects of diabetes. However, lack of awareness and expensive clinical tests are the primary reasons to skip clinical diagnosis and take preventive methods in lower-income countries like Bangladesh, Pakistan, and India. From this perspective, the study aims to build an automated machine learning (ML) model, which will predict diabetes at an early stage using socio-demographic characteristics rather than clinical attributes. Because clinical features are not always known to all people from lower-income countries. To find the best fit supervised ML classifier of the model, we applied six classification algorithms and found that RF outperformed with an accuracy of 99.36%. In addition, the most significant risk factors were found based on the SHAP value by all the applied classifiers. The study reveals that polyuria, polydipsia, and delayed healing are the most significant risk factors for growing diabetes. The findings indicate that the proposed model is highly capable of predicting diabetes in the early stages.

Carbon dioxide (CO2), a major greenhouse gas, capture and separation has recently become a crucial technological solution to reduce atmospheric emissions from fossil fuel burning. Thereafter, many efforts have been put forwarded to reduce the burden on climate change by capturing and separating them especially from larger power plants by the utilization of different technologies. Those technologies have often suffered from high operating cost and huge energy consumption. On right side, physical process such as adsorption is very cost effective process which have been widely used to adsorb different contaminants including CO2. Henceforth, this review covers the overall efficacies of CO2 capture by the utilization of carbon based materials through adsorption technology. Subsequently, we also address the associated challenges and future opportunities of carbon based materials (CBMs). For CO2 capture, it was found that CBMs followed the order of carbon nanomaterials (i.e., graphene, graphene oxides, carbon nanotubes and their composites) < mesoporous -microporous or hierarchical porous carbons < biochar and activated biochar < activated carbons.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

Worldwide the severity of abiotic stress like heat, drought, salinity, cold, waterlogging, etc. are being increased because of global warming. Wheat crops must adapt to harsh environments through physiological, molecular, and genetic manipulation. Because of abiotic stress, reactive oxygen species (ROS) and reactive nitrogen species (RNS) produced in wheat plants break down DNA and RNA bases, protein, lipid, and other macro- and micromolecules, resulting in stunted growth and yield decline. Abiotic stress also induces the crop's molecular functions, physiological, biological, and cellular processes, and their compositions. Different stressors like high light intensity, heat, drought, and salinity also impair photosynthesis damaging various pigments. Antioxidant enzymes, such as catalase (CAT), superoxide dismutase (SOD), peroxidase (POD), and ascorbate peroxidase (APX), etc. synthesized in harsh environments can ameliorate ROS/RNS produced in oxidative stress. Under abiotic stress, heat shock proteins (HSPs) heat shock transcription factors (HSFs) in heat stress, and dehydration-responsive element binding proteins (DREBs) in drought stress are activated to synthesize proteins to mitigate the deleterious effects of those stressors. Na⁺ exclusive genes (NAX1, NAX2) and Na⁺/H⁺ (K⁺) antiporter genes (NHX1, NHX2) hinder those ions from uptake into leaf sheaths and blades of wheat resulting in the declination of salinity in plants. Exogenous hormones like gibberellic acid, salicylic acid, and melatonin, etc., and osmoprotectants like proline, and gene manipulation in plants through genetic engineering are being employed to mitigate the toxic effects of abiotic stress on plants, as portrayed in many literatures. The review depicts how abiotic stress affects phenotypic, physiological, and molecular structures and functions of wheat crops, and their mitigation strategies to lessen their noxious effects on wheat.

COVID-19 has a severe risk of spreading rapidly, the quick identification of which is essential. In this regard, chest radiology images have proven to be a practical screening approach for COVID-19 affected patients. This study proposes a deep learning-based approach using Densenet-121 to detect COVID-19 patients effectively. We have trained and tested our model on the COVIDx dataset and performed both 2-class and 3-class classification, achieving 96.49% and 93.71% accuracy, respectively. By successfully utilizing transfer learning, we achieve comparable performance to the state-of-the-art method while using 15x fewer model parameters. Moreover, we performed an interpretability analysis using Grad-CAM to highlight the most significant image regions at test time. Finally, we developed a website that takes chest radiology images as input and detects the presence of COVID-19 or pneumonia and a heatmap highlighting the infected regions. Source code for reproducing results and model weights are available.

Irrigation and fertilizer are two essential factors affecting rice root traits and yield. In this respect, a pot experiment was performed at the boro (dry season irrigated) season of 2021-22 in the Department of Agronomy of Bangladesh Agricultural University, Mymensingh, Bangladesh. The variety Binadhan-10 was planted at two irrigation conditions i.e. saturation (S) and continuous flooding (CF); two potassium (K) dose e.g. 65 kg ha-1 (K65) and 98 kg ha-1 (K98) and two nitrogen (N) dose i.e. 140 kg ha-1 (N140) and 210 kg ha-1 (N210). The experiment was laid in split plot design and replicated thrice. The findings confirmed the effectiveness of irrigation, K and N on root number (RN), root length (RL), root volume (RV), leaf area index (LAI), total dry matter (TDM), yield attributes and yield. Considering interaction among irrigation, K and N, S condition with K65 and N140 showed best performance. At 80 DAT, the highest RN (373.00), RL (1700.00 cm), RV (8.90 cm3 hill-1), LAI (4.94) and TDM (25.83 g plant-1) was obtained from this combination. Grain yield (GY) and root traits except root porosity, showed a significant positive association. Grain yield (GY) was highest (27.12 g pot-1) in S condition with K65 and N140.

Molecular dynamics(MD) simulations are playing an increasingly important role in structure-based drug discovery (SBDD). Here we review the use of MD for proteins in aqueous solvation, organic/aqueous mixed solvents (MDmix) and with small ligands, to the classic SBDD problems: binding mode and binding free energy predictions. The simulation of proteins in their condensed state reveals the solvent structure and preferential interaction sites (hot spots) on the protein surface. This information is largely transferable across all classes of protein ligands (from water to drugs) and can be used very effectively to understand ligand recognition and improve the predictive capability of well-established methods such as molecular docking. MD simulations for protein and drug or drug-like compounds are now being used but are still computationally expensive and can only be applied to specific cases. On the other hand, MDmix simulations can now be used in SBDD and we will describe the latest developments and implementations. We expect to see an increase in the application of these techniques to a plethora of protein targets to identify new drug candidates with the advent of new tools and faster computers.

Presently, smartphones support a large range of applications, many of which require high computing power. This presents a problem because smartphones offer limited computing power, storage, and energy. Fortunately, Cloud computing (CC) is rapidly becoming known as the state of the art technology in the computer world. CC allows users to use unlimited dynamic resources when necessary. Mobile Cloud Computing (MCC) is integration into a mobile environment of the concept of cloud computing which eliminates barriers to the performance of mobile devices. The demand for mobile cloud applications and mobile user services is strong. This gives MCC a great opportunity to do business and research. However, security problems are a major obstacle to the adaptability of mobile cloud computing. This study presents the definitions of Cloud Computing, Mobile Computing (MC) and Mobile Cloud Computing including the architecture and applications of MCC. Furthermore, it discusses the challenges and opportunities faced in MCC.

From 2008 to 2024, the Newborn Screening Translational Research Network (NBSTRN), part of the National Institute of Child Health and Human Development (NICHD) Hunter Kelly Newborn Screening Program, served as a robust infrastructure to facilitate groundbreaking research in newborn screening (NBS), rare disease, and genomics. Over fifteen years, NBSTRN developed into a significant international network, supporting innovative research on novel technologies to screen, diagnose, treat, manage, and understand the natural history of more than 280 rare diseases. A key component of these efforts has been the development of resources and expertise for the newborn screening community in ethical, legal, and social issues (ELSI). This paper presents findings from a survey conducted by the NBSTRN team with input from one of theNBSTRN's expert workgroups, the Bioethics and Legal Workgroup. With responses from 88 members of the NBS community including researchers and state NBS programs, the survey found that individuals rely on internal and collegial ELSI resources and highlighted a substantial demand for structured, accessible training and resources. The survey’s insights emphasize the importance of privacy and informed consent in NBS research, and suggested a need for improved collaborative tools and educational programs focused on ELSI for the NBS community. The survey results may inform future efforts in ELSI and NBS research including the development of expanded ELSI tools that leverage digital platforms and consultative services.

The Internet of Medical Things (IoMT) is playing a pivotal role in the healthcare sector by allowing faster and more informed hospital care, personalized treatment, and medical solutions. A very effective and trustworthy solution for resource-constrained medical devices is provided by Physical Unclonable Functions (PUF) - based identity and authentication systems, however they are not yet entirely reliable. This paper proposes VXorPUF, a Vedic Principles - Based Hybrid XOR Arbiter PUF. Modeling attacks were performed on the proposed architecture and an accuracy of 49.80 % was achieved. Uniqueness, Reliability and Randomness were the figures of merit used to evaluate PUF.

Real-time energy management of a converter-based microgrid is difficult to determine optimal operating points of a storage system in order to save costs and minimise energy waste. This complexity arises due to time-varying electricity prices, stochastic energy sources and power demand. Many countries have imposed real-time electricity pricing to efficiently control demand side management. This paper presents a particle swarm optimisation (PSO) for the application of real-time energy management to find optimal battery controls of a community microgrid. The modification of the PSO consists in altering the cost function to better model the battery charging/discharging operations. As optimal control is performed by formulating a cost function, it is suitably analysed and then a dynamic penalty function in order to obtain the best cost function is proposed. Several case studies with different scenarios are conducted to determine the effectiveness of the proposed cost function. The proposed cost function can reduce operational cost by 12% as compared to the original cost function over a time horizon of 96 hours. Simulation results reveal the suitability of applying the regularised PSO algorithm with the proposed cost function, which can be adjusted according to the need of the community, for real-time energy management.

CCNs are specific type of matricellular proteins, which are essential signaling molecules, and play multiple roles in multicellular eukaryotes. This family of proteins consists of six separate members in mammals. The architecture of CCN proteins is multimodular and comprises four distinct motifs. CCN proteins achieve their specific physiological functions by binding to integrin receptors. The CCN family has been implicated in both cure and disease with impacts on biological interactions, such as cell adhesion, chemotaxis and migration, mitogenesis, cell survival, angiogenesis, differentiation, tumorigenesis, immune functions, chondrogenesis, and wound healing. Breast cancer is the most commonly diagnosed cancer worldwide and the leading cause of cancer mortality among women triggered by atypical expression of CCNs. A favorable or unfavorable association between various CCNs has been reported in patients with breast carcinomas. Aberrant expression of CCN1 intensifies the proliferation of epithelial cells that line the lobes and ducts of the breast. Evidence also shows that the expression of CCN2 can ameliorate tumor growth and metastasis. However, CCN3 (NOV), CCN5 (WISP-2), and CCN6 (WISP-3) are consistent with neoplastic development and metastasis repression. Particular CCN members can develop tumors and cancer progression, whereas others can competitively counter the processes. Several studies have been conducted on CCN proteins and cancer in recent years. In our study, we intend to provide an overview of those research works while keeping breast carcinoma on focus. We believe that the importance of the CCN protein family in breast cancer should be reconsidered.

Staphylococcus aureus is a major food-borne pathogen. The ability of S. aureus to produce biofilm is a significant virulence factor triggering its persistence in hostile environments. In this study, we screened a total of 420 different food samples and human hand swabs to detect S. aureus and to determine their biofilm formation ability. Samples analyzed were meat, milk, egg, fish, fast foods, and hand swabs. S. aureus were detected by culturing, staining, biochemical, and PCR. Biofilm formation ability was determined by Congo Red Agar (CRA) plate and Crystal Violet Microtiter Plate (CVMP) tests. The icaA, icaB, icaC, icaD, and bap genes involved in the synthesis of bio-film-forming intracellular adhesion compounds were detected by PCR. About 23.81% (100/420; 95% CI: 14.17-29.98%) samples harbored S. aureus as revealed by detection of the nuc gene. CRA plate revealed 20% of S. aureus isolates as strong biofilm producers, while 69% and 11% as in-termediate and non-biofilm producers, respectively. By the CVMP staining method, 20%, 77%, and 3% of the isolates were found strong, intermediate, and non-biofilm producers. Furthermore, 21% of S. aureus isolates carried at least one biofilm-forming gene, where icaA, icaB, icaC, icaD, and bap genes were detected in 15%, 20%, 7%, 20%, and 10% of the S. aureus isolates, respectively. Bivariate analysis showed high significant correlations (p<0.001) between any of the two adhesion genes of S. aureus isolates. To the best of our knowledge, this is the first study in Bangladesh describing the detection of biofilm-forming S. aureus from foods and hand swabs with molecular-based evidence. Our findings suggest that food samples should be deemed a potential reservoir of biofilm-forming S. aureus that indicates a potential public health significance.

A single paragraph of about 200 words maximum. Electroencephalography (EEG) accumulates the electrical activities of human brain. It is an easy and cost effective tool to characterize motor imagery (MI) task used in brain computer interface (BCI) implementation. The MI task is represented by short time trial of multichannel EEG. In this paper, the raw EEG is decomposed into a finite set of narrowband signals obtained from individual EEG channels using Fourier transformation based bandpass filter. Each of the subband signals represents narrowband rhythmic components which characterize the brain activities related to motor imagery. The subband signals are arranged to extent the dimension of EEG trial in spatial domain. The spatial features are extracted from the set of extended trials using common spatial pattern (CSP). An optimum number of features are used to classify the motor imagery tasks represented by EEG trials. Artificial neural network is used to classify MI tasks. The performance of the proposed method is evaluated using two publicly available benchmark datasets. The experimental results show that it performs better than the recently developed algorithms.

CO2 geological sequestration in coal seams can achieve the dual objectives of CO2 emission reduction and enhanced coalbed methane production, making it a highly promising carbon capture and storage technology. However, the injection of CO2 into coal reservoirs in the form of supercritical fluid (ScCO2) leads to complex physicochemical reactions with the coal seam, altering the properties of the coal reservoir and impacting the effectiveness of CO2 sequestration and methane production enhancement.In this paper, theoretical calculations based on ReaxFF-MD were conducted to study the interaction mechanism between ScCO2 and the macromolecular structure of both low-rank and high-rank coal, to address the limitations of experimental methods. The reaction of ScCO2 with low-rank coal and high-rank coal exhibits significant differences. At swelling stage, the low-rank coal experiences a decrease in aromatic structure and aliphatic structure, high-rank coal shows an increase in aromatic structure and a decrease in aliphatic structure, while swelling phenomenon is more pronounced in high-rank coal. At dissolution stage, low-rank coal is initially decomposed into two secondary molecular fragments, and then recombine to form new molecular structure, the aromatic structure increased and the aliphatic structure decreased. In contrast, high-rank coal occurs stretches-breakage-movement-reconnection, a reduction in aromatic structure and an increase in aliphatic structure.The primary reasons for these variations lie in distinct molecular structure compositions and the properties of ScCO2, leading to different reaction pathways of functional group and aromatic structure. The reaction pathways of functional groups and aromatic structures in coal can be summarized as follows: the breakage of the O-H bond in hydroxyl groups, the breakage of the C-OH bond in carboxyl groups, transformation of aliphatic structures into smaller hydrocarbon compounds or formation of long-chain alkenes, and various pathways involving broken, rearrangement, recombination of aromatic structures. In low-rank coal, there is a higher abundance of oxygen-containing functional groups and aliphatic structures. The breakage of O-H and C-OH chemical bonds results in the formation of free radical ions, while some aliphatic structures detach to produce hydrocarbons. Additionally, some of these aliphatic structures combine with carbonyl groups and free radical ions to generate new aromatic structures. Conversely, in high-rank coal, the lower content of oxygen-containing functional groups and aliphatic structures, along with stronger intramolecular forces, results in fewer chemical bond breakages and makes it less conducive to the formation of new aromatic structures.These results elucidate the specific deformations of different chemical groups, offering a molecular-level understanding of the interaction between CO2 and coal.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

Polyphenols, long-used components of medicinal plants, have drawn great interest in recent years as potential therapeutic agents because of their safety, efficacy, and wide range of biological effects. Approximately 74% of the world's population still uses plant-based medicines, indicating the ongoing significance of phytochemicals for human health. The study emphasizes the growing body of research examining the role of polyphenols in uncovering their anti-adipogenic and anti-obesity properties. Functions of polyphenols including phenylpropanoids, flavonoids, terpenoids, alkaloids, glycosides, and phenolic acids are distinct due to changes in chemical diversity, and structural characteristics. This review methodically investigates the mechanism of how naturally occurring polyphenols mediate obesity and metabolic function. To this end, hormonal control of hunger has the potential to inhibit pro-obesity enzymes such as pancreatic lipase, the promotion of energy expenditure, and the modulation of adipocytokine production. Specifically, polyphenols affect insulin, a hormone that is essential for regulating blood sugar, and they also play a role in part in a complex web of factors that affect the progression of obesity. This review also explores the immunomodulatory properties of polyphenols, providing insight into their ability to improve immune function. The effects of polyphenols on gut health, improving the number of commensal bacteria, cytokine production suppression, and immune cell mediation, including natural killer cells and macrophages. Taken together, continuous studies are required for prudent and precise mechanisms underlying polyphenols' therapeutic potential in obesity and immunomodulation. In the interim, this review emphasizes the holistic approach to health and promotes the consumption of a wide range of foods and drinks high in polyphenols. This review lays the groundwork for future developments, indicating that the components of polyphenols and their derivatives may provide the answer to urgent worldwide health issues. This compilation of the body of knowledge paves the way for future discoveries in the global treatment of pressing health concerns in obesity and metabolic diseases.

Multidrug resistant organisms (MDROs) outbreaks have been steadilyincreasing in Intensive care units (ICUs). Still, healthcare institutions and workers (HCW) reached no unanimity on how and when implementing infection prevention and control (IPC) strategies. We aimed to provide a pragmatic, physician practice-oriented, resume of strategies towards different MRDOs outbreaks in ICU. We performed a narrative review on IPC in ICUs, investigating patient-to-staff ratios, education, isolation, decolonization, screening and hygiene practices, outbreak reporting, cost-effectiveness, reproduction-number(R0), and future perspectives. The most effective IPC strategy remains unknown. Most studies focus on a specific pathogen or disease, making the clinician losing the big picture. IPC strategies proved their cost-effectiveness regardless typology, country, or pathogen. A standardized, universal, pragmatic protocol for HCW education should be elaborated. Likewise, a rapid outbreak recognition tool elaboration (i.e., an easy-to-use mathematical model) would improve early diagnosis and spreading prevention. Further studies are needed to express in favor or against MDROs decolonization. New promising strategies are emerging and need to be tested in the field. The lack of IPC strategies application has made, and still makes ICUs a major MDROs reservoir into the community. In a not-too-distant future genetic engineering and phage therapies could represent a plot-twist in MDROs IPC strategies.

Businesses use technological and social media marketing to respond to the Covid-19 pandemic. This study aims to understand better the factors that impact the spread of new technologies, the effectiveness of social media advertising, and the longevity of businesses. The study used a quantitative strategy based on partial least squares structural equation modeling to learn about the phenomenon of interest as much as possible. Dhaka, Bangladesh, small and medium-sized businesses participated in the survey. According to the findings, the popularity of internet and e-business technologies may be attributed to their apparent usefulness and ease of use. It is connecting internet/e-business technology, social media marketing, and the long-term success of small and medium-sized enterprises. Still, the expense factor was insufficient to prove that SMEs engage in social media advertising. Mediating effects between components may be better understood via internet/e-business technology and social media marketing, as shown by this study. This study is the first of its kind in Bangladesh and sheds light on the resilience of SMEs in the face of the Covivirus-19 pandemic, notwithstanding its focus on the capital city of Dhaka.

Medicinal plants are generally defined as rare herbals with potent medicinal activities that can be used as an alternative treatment for diseases. Recent studies exploring novel medicine developments, originating from folk-medicinal practices challenges this notion and suggests that both the circumference of the term medicinal plant and their potential application covers a substantially extensive verse than previously suggested. While medicinal plants are not limited to the borders of any country, Bangladesh and its south-east Asian neighbors do boast a huge collection of potent medicinal plants with considerable folk-medicine history compared to most other countries of the world. MPDB 2.0 is the continuation of MPDB 1.0, it serves as both a data repertoire for medicinal of Bangladesh and a user-friendly interface for researchers, health practitioners, drug developers, and students who wish to study the various medicinal & nutritive plants scattered around Bangladesh and the underlying phytochemicals contributing to their efficacy in folk medicine. While in developing MPDB 2.0 human diseases have been highly focused upon, the information in this database is not limited in its application for human diseases or diseases only, as many of the plants indexed here can serve in developing biofuel or bioremediation technologies or nutritive diets or cosmetics, etc. MPDB 2.0 comprises a collection of more than five hundred medicinal plants from Bangladesh along with a record of their corresponding scientific, family, and local names together with their utilized parts, information regarding ailments, active compounds, and PubMed ID of related publications.

This study aimed to develop chitosan-based apigenin spray dried solid dispersion using 1:1,1:1.5,1:2 w/w ratios. The results of process yield and drug assay were found to be (87.5%, 94.2%, and 95.86%), (95.2 ±1.34%), (99.5 ±0.85%), and (97.6 ±2.42%), respectively, for AC1, AC2, and AC3. Flow properties indicate the free flow of powders. FTIR revealed compatibility among chitosan and apigenin, and DSC and XRD showed prepared solid dispersion was on a molecular level and available in amorphous. In contrast, SEM images reflect irregular block and near-spherical shape elongated particles in the selected AC2. The antimicrobial examination reflects that AC2 was more effective against Gram-positive, negative, and fungal strains. AC2 SDSDs has more anti-oxidant property compared to pure flavonoid (AGN). Anti-proliferative activity against A549 lung cancer cell lines showed better anti-cancer activity by AC2 SDSDs. The selected AC2 SDSD filled in a 3D shell pill and further characterized for 3D shell pill for dissolution profiles and stability studies. The product has sustained release and similar release profiles after three months of storage. The findings suggest that the AC2 SDSDs may be a promising candidate for further development as a 3D printed drug delivery system for treating multiple disease conditions using model flavonoid- apigenin.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

COVID-19 infection is extremely dangerous for persons with comorbidities such as kidney disease and diabetes. Although many people of all ages and socioeconomic backgrounds have suffered due to this pandemic, those with underlying medical conditions like kidney disease and diabetes are more vulnerable to becoming infected with COVID-19 related to weak immunity. However, the role of vaccination in the co-infection of COVID-19 with diabetics is not available in the literature. Therefore, we examine the unique challenges presented by the co-infection of COVID-19 in individuals with diabetes, focusing on its disease transmission dynamics. A mathematical modelling technique is to be employed in this work to analyse the dynamics of COVID-19 outbreaks with seven compartments, including vaccination with comorbidities such as diabetes. We also investigated analytically by displaying the solutions' existence, boundedness, positivity and sensitivity. After calculating the basic reproduction numbers, the stability analysis of model equilibrium points is also covered. If the reproduction numbers are less than unity, the disease-free equilibrium points of the model appear to be both locally and globally stable. The findings of this study are that as the vaccination rate rises, the incidence of COVID-19 and its co-infections with diabetes decreases. Effective disease treatment strategies may be based partly on the possible impact of vaccination on the co-infection of COVID-19 related to diabetic disease insights.

By 2024, artificial intelligence (AI) will have had a revolutionary impact on cyber security, putting the sector at a critical turning point. This article explores the significant influence AI has had on cyber security procedures, outlining the progress made as well as the difficulties faced. artificial intelligence (AI) has transformed threat detection and response systems, allowing for proactive security tactics against a constantly changing array of cyber threats. By utilizing neural networks and machine learning algorithms, artificial intelligence (AI) systems can predict possible security breaches, detect unusual trends, and automatically reduce risks in real-time. These capabilities are unparalleled. Nevertheless, despite these impressive advancements, worries about data privacy, adversarial attacks, and ethical ramifications remain significant. Moreover, the never-ending game of cat and mouse between cyber attackers and defenders continues, requiring constant innovation and adaptability in cyber security strategies driven by Artificial Intelligence. In addition to providing insights into its implications for protecting digital assets and bolstering resilience against cyber threats in the changing cyber security scenario of 2024, this paper summarizes the current state of the artificial intelligence revolution in cyber security.

This paper explores the ever-changing topic of cybersecurity and provides a summary of the most recent developments. In a time of unparalleled digital revolution and changing threat environments, being aware of new trends is essential to managing risks and protecting important assets. To highlight significant advancements in fields like artificial intelligence and machine learning for threat detection, the proliferation of IoT devices and related security challenges, the emergence of quantum-resistant cryptography, the development of zero trust architectures, and the growing significance of cybersecurity awareness and education, the report synthesizes insights from industry experts, academic research, and real-world case studies. The goal of the report's analysis of these patterns is to provide stakeholders with useful information so they may modify their cybersecurity plans and strengthen defenses against new threats. Cybersecurity plays a significant role in the IT industry.

The Internet of Things (IoT) is a disruptive technology innovation that has the potential to link billions of gadgets and alter multiple industries. The Internet of Things (IoT) represents a significant advancement in the networking of devices and systems. However, because IoT devices add new attack avenues and vulnerabilities to networks, their rapid proliferation has also caused serious cyber security concerns. The present study investigates the influence of cyber security on the progress of the Internet of Things (IoT), emphasizing the obstacles, prospects, and future paths towards safeguarding the IoT network. This study attempts to shed light on the crucial role that cyber security will play in determining the direction of the Internet of Things through an examination of recent trends, case studies, and research findings.

Blockchain is a shared, unchangeable, decentralized ledger that allows transactions to be recorded securely and transparently via a network of computers. In addition to its significant contributions to cryptocurrencies, blockchain technology has shown promise as a game-changing advancement in cyber security. This study offers a thorough analysis of how blockchain technology is strongly linked to defending against cyber security risks in the modern world. This research clarifies the primary mechanisms of decentralization, immutability, transparency, and cryptographic security by which blockchain improves cyber security through a review of the literature and case studies. Furthermore, the study addresses the difficulties and constraints associated with incorporating blockchain technology into cybersecurity frameworks and proposes potential directions for future research.

The multidrug resistance transporter NorM is an important drug resistance pump and plays a critical role in multidrug resistance in bacteria and mammals. In this study we carried out molecular dynamics simulation to study the mechanism of Na+ binding and dynamical structures of two long loops in the substrate-releasing process in substrate binding NorM. Our simulation study identified several key residues (D41, E261 D377) along the Na+ binding pathway and a multi-state ion-binding mechanism is proposed based on the simulation study. In this proposed model, the transport of Na+ is a multi-stage process with D41 being the first station for binding to Na+, followed by Na+ binding to the second station E262 and finally to the cation-binding site of E262 and D377. During the transport of Na+, the transmembrane components TM1, TM7 and TM2 are rearranged to facilitate the ion transport as well conformational changes of NorM to a closed state. Further, substrate-bound simulation revealed that Loop3-4 and Loop9-10 control the substrate-releasing process.

COVID-19 is now a major global health crisis, can lead to severe food crisis unless proper measures are not taken. Though a number of scientific studies have addressed the possible impacts of COVID-19 in Bangladesh on variety of issues, problems and food crises associated with aquatic resources and communities are missing. Therefore, this study aimed at bridging the gap in the existing situation and challenges of COVID-19 by linking its impact on aquatic food sector and small-scale fisheries with dependent population. The study was conducted based on secondary data analysis and primary fieldwork. Secondary data focused on COVID-19 overview and number of confirmed, recovered and death cases in Bangladesh; at the same time its connection with small-scale fisheries, aquatic food production, demand and supply was analyzed. Community perceptions were elicited to present how the changes felt and how they affected aquatic food system and small-scale fisheries and found devastating impact. Sudden illness, reduced income, complication to start production and input collection, labor crisis, transportation abstraction, complexity in food supply, weak value chain, low consumer demand, rising commodity prices, creditor’s pressure were identified as the primary affecting drivers. Dependent people felt the measures taken by the Government should be based on protecting the health and food security, although it could be detrimental to economic growth in the short term. The study provides insight into policies adopted by the policy makers to mitigate the effects of the pandemic on aquatic food sector and small-scale fisheries.

In modern automobiles, Infotainment High-Performance Computing (HPC) systems play a vital role in enhancing the capabilities of drivers and passengers by providing advanced features consisting of music, navigation, communication, entertainment, etc. However, as the use of information technology in vehicles increases, it results in cybersecurity threats such as data breaches and the loss of sensitive information. To improve the security of the infotainment system in automotive vehicles, the research conducted threat modeling at the component level using Microsoft’s STRIDE tool and performed risk assessment by using SAHARA (Safety-Aware Hazard Analysis and Risk Assessment) and DREAD methodologies to evaluate associated risks. It provides a systematic representation of threats, associated risks, and generic mitigation strategies to counter cybersecurity attacks. Through the threat modeling process, 34 potential security threats were identified. The study also provided a comparative analysis to calculate the risk values of the threats to prioritize for treatment. These identified threats and associated risks need to be considered to avoid potential cyberattacks, before deploying the infotainment HPC system in real-world automotive vehicles.

Oil palm is one of the most important crops in Malaysia. Lately, the production of oil palm has been reduced due to a variety of factors, including the weather and climate. Temperature, wind speed, relative humidity, sunshine, and rainfall distribution all have an impact on palm tree growth and development, which in turn has an impact on oil palm production. This paper aims to investigate the effects of some weather elements (temperature, wind speed, relative humidity, sunshine, and rainfall) on oil palm production in Peninsular Malaysia. Data were analyzed using the Statistical Package for Social Sciences (SPSS 20.0 version), with descriptive statistics, and multiple linear regression (MLR). The MLR model determined the strength of the relationship between oil palm yield (dependent variable) and the changing variables of temperature, sunshine, wind speed, relative humidity, and rainfall (independent variables). The findings revealed that temperature, wind speed, relative humidity, sunshine, and rainfall have a low impact on oil palm production and yield turnover. The R2 value of 0.202 shows that the independent variables explained only 20.2% of the fluctuation in palm oil production. The study recommends working within an integrated approach involving scientific research, planting, improving variety, improving regional academic leadership, and engaging private and public stakeholders, emphasized collaborative efforts with researchers in consumer countries, and strengthening the capacity of growers to best agroecological practices.

Background: The practice of self-medication is common worldwide and is an important component of medical self-care. However, the practice can be dangerous and is linked to various risks for the patients and the entire community. This study aimed to estimate the prevalence and factors associated with self-medication among Bangladeshi adults. Methods: A cross-sectional survey was conducted between April and June 2021 among Bangladeshi adults (aged &gt;19 years) using convenient sampling. A total of 1320 data were collected through face-to-face interviews using a standardized questionnaire. Multivariable logistic regression analysis was used to identify factors associated with self-medication practice (SMP). Results: Overall, 41% of adults in our survey reported SMP. The most common illnesses that prompted SMP were common cold/flu (66.4%), gastric problems (65%), and headache (64.4%). The most frequent reasons for SMP were to get better services (30.59%), perceive SMP without side effects (23.28%), and save time with effectiveness (14.56%). Potential risk factors included 10 years (AOR = 1.91; 95% CI: 1.04 - 3.50) and &gt;12 years of schooling (AOR = 5.03; 95% CI: 2.27 - 11.15), being a businessman (AOR = 4.64; 95% CI: 1.74 - 12.37), having ≤6 family members (AOR = 2.13; 95% CI: 1.40 - 3.24), being a member of a social group (AOR = 1.53; 95% CI: 1.10 - 2.12), a health status check after every six months (AOR = 1.52; 95% CI: 1.08 - 2.13), and current ill-health (AOR = 1.41; 95% CI: 1.06 - 1.87). Protective factors identified included ≤30 years of age (AOR = 0.40; 95% CI: 0.17 - 0.93), and practice of modern (AOR = 0.39; 95% CI: 0.22- 0.69) and herbal (AOR = 0.45; 95% CI: 0.21- 0.97) healing types. Conclusion: More than one-third of the study participants reported practicing self-medication. Increasing the community’s awareness of the extreme consequences of SMP and not just the average experience might sway individuals away from SMP, and implementing strict jurisdiction could be a way to minimize the SMP.

One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

This research introduces a pioneering solution to the challenges posed by gastrointestinal tract (GI) cancer in radiation therapy, focusing on the imperative task of precise organ segmentation for minimizing radiation-induced damage. GI imaging has historically used manual demarcation, which is laborious and uncomfortable for patients. We address this by introducing the ResECA-U-Net deep learning model, a novel combination of the UNet and ResNet34 architectures. Furthermore, we further augment its functionality by incorporating the Efficient Channel Attention (ECA-Net) methodology. By utilizing data from the UW-Madison Carbone Cancer Centre, we carefully investigate several image processing techniques designed to capture critical local characteristics. With its foundation in computer vision concepts, the ResECA-U-Net model is excellent at extracting fine details from GI images. Sophisticated metrics such as intersection over union (IoU) and the dice coefficient are used to evaluate performance. Our study's outcomes demonstrate the effectiveness of the suggested method, yielding an impressive 96.27% Dice coefficient and 91.48% IoU. These results highlight the significant contribution that our strategy has made to the advancement of cancer therapy. Beyond its scientific merits, this work has the potential to significantly enhance cancer patients' quality of life and provide better long-term outcomes. Our work is a significant step towards automating and optimizing the segmentation process, which can potentially change how GI cancer is treated completely.

Background: Intrauterine transfusion (IUT) of the donor and partial exchange (pET) of the recipient is a temporizing treatment for pregnancies with Twin Anemia Polycythemia Sequence (TAPS). We sought to give a detailed description of the procedural approach and outcomes for sequential donor IUT and recipient pET in TAPS. Methods: Retrospective study of spontaneous TAPS referred to the Johns Hopkins Center for Fetal Therapy treated with donor IUT followed by recipient pET utilizing a double-syringe set up. Procedure characteristics and outcomes as well as accuracy of existing transfusion formulas were analyzed and compared with the literature. Results: 5 of 78 patients with spontaneous TAPS underwent a total of 19 combined IUT/pET procedures (median first procedure to delivery interval 5.6 weeks [interquartile range IQR 1.9-6.0]). One pET was stopped for fetal decelerations. Patients delivered at 33.0 weeks [IQR 31.9-33.3] with two survivors and no neonatal transfusion requirements. IUT volumes were 48 ml [IQR 39-63 ml] and pET volumes 32 ml [IQR 20-50] utilizing aliquots of 5 – 20 mls for the latter (p=0.021). For IUTs, assumption of a fetal blood volume below 150 ml/kg underestimated required transfusion volume. For pETs, all formulas required adjustment of dilution volume based on bedside testing (p&lt;0.05 for all). Conclusions: Donor transfusion followed by partial exchange in the recipient can prolong pregnancy in spontaneous TAPS and obviate the need for neonatal transfusion. A double-syringe setup facilitates efficient saline exchange. Because the accuracy of volume formulas is limited, bedside testing is recommended to achieve the target hemoglobin.

The importance of bio robotics has been increasing day by day. Researchers are trying to mimic nature in a more creative way so that, the system can easily adopt the complex nature and its environment. Hence, bio robotic gripper plays a role in physical connection between the environment and bio robotics system. While handling the physical world in biorobots gripper, the complexity occurs in feedback system where sensor plays a vital role. Therefore, human centered gripper sensor has a good impact on bio robotics field. But categorical classification and their selection process is not very systematic. This review paper follows PRISMA methodology to summarize the previous works on bio robotics gripper sensor and its selection process.. This paper discusses challenges in soft robotics systems, and the importance of sensing systems to facilitate critical control mechanisms along with their selection considerations. Furthermore, a classification of soft actuation based on gripper has been introduced. Moreover, some unique characteristics for soft robotics sensor are explored namely compliance, flexibility, multifunctionality, sensor nature, surface properties, and material requirements. In addition, a categorization of sensors for soft robotic gripper in terms of modalities has been established ranging from the tactile and force sensor to slippage sensor. Various tactile sensors ranging from piezoelectric sensing to optical sensing are explored as it has utmost importance in soft gripper to effectively address the increasing requirements for intelligence and automation. Finally, taking everything into consideration, a flow diagram has been suggested for selecting sensors specific to soft robotics applications.

The rapid expansion of Bangladesh's financial infrastructure, coupled with the increasing digitization of banking services, underscores the critical importance of cybersecurity. Machine learning and deep learning methodologies have emerged as potent tools in combating cyber threats such as intrusion, malware, and fraud. By harnessing artificial intelligence and data-driven analysis, these techniques enable real-time scrutiny of vast banking data, facilitating proactive defense against cyberattacks. Bangladesh's evolving financial landscape, characterized by governmental digitalization initiatives and a national financial inclusion strategy, heightens the imperative for robust cybersecurity measures. This paper explores the application of machine learning and deep learning techniques in bolstering banking cybersecurity within the context of Bangladesh's burgeoning digital economy.

The once near-extinct Russell’s viper has recently come back to the area beyond its historical range. A couple of decades ago, its distribution was confined to 11 districts of Bangladesh. Hence, the study aims to update the distributional map of Russell’s Viper (Daboia russelii) across the country and find out the surges' causal factors. Both primary and secondary data were utilized in this study. It revealed that the distributional range of this snake was expanded from 22 to 33 districts in 2024. The respondents noted that climatic stressors like high humidity accompanied by hot weather, increased salinity, and increased frequency of flooding facilitated the spreading of the viper across the country. The cropping pattern and crop diversification were another major contributing factor. The shifting of the single-cropped area to a multi-cropped area in the Barind tract increased its main prey rats. Contrarily, the killing of natural predators such as foxes, monitor lizards and mongoose led to the rise in the snake population. The destruction of vegetation coverage in the upper part of the Padma Basin facilitated the movement of Russell's vipers downstream.

Microplastics, which are plastic particles smaller than 5 mm in size, are a growing environmental concern since they have been found in oceans, rivers, lakes, and even on land. These tiny particles can escape water filtration systems and end up in water bodies as well as through the degradation of the larger plastic products causing serious environmental and food safety concerns. This research represents the magnitude of this pollution, characterization of microplastic contamination, its type of polymer, and possible sources of this pollution in the rivers around Dhaka, Bangladesh. Quantitative analyses were done following the method suggested by the NOAA and other conventional methods. Among the rivers, Buriganga has the highest microplastic pollution with 3.654 items/L in surface water and 43.125 items/kg in sediment. The concentration in Shitalakshya and Turag rivers are 3.011 items/L and 2.051 items/L in surface water and 34.875 and 17.875 items/kg in sediment respectively. ANOVA test revealed a significant difference between the concentration level of microplastic in the surface water of the Burigana and Turag rivers. A positive correlation between the concentration level of microplastic in the surface water and the sediment was also found. On average 58% of the microplastics were found to be fibrous in surface water. Qualitative analyses were done to find the characteristics and chemical composition of the microplastics. Through the use of FTIR spectroscopy, the study identified different kinds of synthetic polymers in the sample including polyamide (Nylon), polyethylene (PE), polystyrene (PS), polypropylene (PP), polyethersulfone (PES), polyvinyl chloride (PVC), and polyethylene terephthalate (PET) and polyethylene were the most abundant polymer in the samples. This study involved the investigation of three distinct rivers located in the vicinity of Dhaka city

Background: Oral cancer (OC) is serious health concerning issue that has a high fatality rate. The oral cavity has seven kinds of OC, including the lip, tongue, and floor of the mouth, as well as the buccal, hard palate, alveolar, retromolar trigone, and soft palate. The goal of this study is to look into new biomarkers and important pathways that might be used as diagnostic biomarkers and therapeutic candidates in OC. Methods: Publicly available repository the Gene Expression Omnibus (GEO) was responsible to collect OC-related datasets. GSE74530, GSE23558, and GSE3524 microarray datasets were collected to apply analysis. Minimum cut-off criteria of |log fold-change (FC)| > 1 and adjusted p < 0.05 were applied to figure out the up-regulated and down-regulated differential expression genes (DEGs) from the three datasets. After that only common DEGs in all three datasets were collected to apply further analysis. Gene ontology (GO) and Pathway analysis were implemented to explore the functional behaviors of DEGs. Then protein-protein interaction (PPI) networks were built to identify the most performed genes, clustering algorithm was also implemented to identify complex parts of PPI. TF-miRNA networks were also constructed to study deeply about OC-associated DEGs. Finally, top gene performers from PPI networks were used to apply drug signature analysis. Results: After applying filtration and cut-off criteria 2508, 3377, and 670 DEGs were found for GSE74530, GSE23558, and GSE3524 respectively, and 166 common DEGs were found in every dataset. The GO annotation remarks that most of the DEGs were associated with the terms of type I interferon signaling pathway. The pathways of KEGG reported that the common DEGs are related to the Cell cycle and Influenza A. The PPI network holds 88 nodes and 492 edges and CDC6 had the highest number of connections. 4 clusters were identified from the PPI. Drug signatures doxorubicin and resveratrol showed high significance according to the hub genes. We anticipate that our bioinformatics research will aid in the definition of the pathophysiology and the development of new therapies for OC.

Introduction: In the marginalised countries most neglected health issue is Newborn mortality. A study was undertaken to assess the influence of factors and newborn care practices influencing newborn health in the rural area of Bareilly district. Methodology: The Descriptive cross-sectional study was organized in the rural areas of Bareilly. Study participants were selected based on the mothers who gave birth to a baby during the last six months. The mothers who delivered in that area within six months were included, and using the semi-structured questionnaire, data was collected. Data analyzed using Microsoft Excel and SPSS 2021 version for windows. Results: Mothers initiating early breastfeeding were more commonly 78 (52.3%) observed in the younger mothers at 24-29 years, followed by 48(32.3%) at 30-35 years, the difference was statistically significant (p<0.05). Delayed bathing was observed in nearly 125 (70.1%) three fourth in the age of 24-29 years, followed by 29 (16.8%) in the age period 30-35 years. It was observed that unsafe cord care practices were observed more among 8(53.4%) nuclear families than 7(46.6%) joint families, and it was found to be statistically insignificant. Conclusion: The practice of essential newborn care still needs to improve in Bareilly; there is a need to create awareness to the mothers and family members on newborn and early neonatal care aspects, such as promoting exclusive and early initiation of breastfeeding and delayed bathing practices.

Wheat is threatened by global warming. This study aimed to characterize based on DNA profile and identify heat-tolerant wheat genotypes. Fifteen wheat genotypes were sown in Nov 21 and Dec 21 and evaluated within 13 SSR markers. A dendrogram classified the genotypes into two main groups. The highest genetic distances (0.93) were drawn between BAW 1290 and BARI Gom 28, and the lowest one between Nadi 2 and BAW 1147. Heat susceptibility index (HSI) values for 1000-grain weight (TGW) and grain yield indicated moderate heat tolerance in Cluster I genotypes (HSI 0.50-1.00), closely matching Group A's Cluster II members. In Group B, Cluster III genotypes had higher HSI (1.04-1.23) and significant reductions in TGW and grain yield under heat stress, indicating heat susceptibility. The varieties BARI Gom 25, 26, 27, 28, 29, and 30 were identified as heat-stress tolerant. This research provides insights for future heat stress-molecular breeding programs.

Bangladesh faces significant wheat grain deficiency compared to its demand due to the lengthy process (10-12 years) required to release a variety through a conventional breeding approach. Traditional breeding methods involve several years of various types of crosses between male and female parents and/or progenies, along with recurrent selection-crossing to obtain a homozygous line (F₁ to F₆ generations) with desired traits within almost 10 years. The double haploid (DH) method is also a time-saving, easier, and more reliable technique to achieve the desired traits in homozygous lines within 2-3 years. DH lines were produced by crossing two F₁ hybrids of spring wheat with maize. 0.1% solution of colchicine was applied to produce DH of F₂ progeny of wheat in the study. 80.8% (340) of the 421 pollinated florets from the two F₁ wheat hybrids were produced as green parthenocarpic caryopses (GPCs) (F₂). 35 of the 70 rescued embryos (or 20.6% of the GPCs) germinated. The germinated embryos regenerated 10 haploid green plants (14.3% of total embryos). After being applied colchicine, 8 of the regenerated haploid (H₁) plants made it. Out of the 8 plants that made it through, only one developed homozygous double haploid seed (DH₁ seed). These seeds were multiplied to produce DH₂, used in the preliminary yield in the next year. The results demonstrated the potential of this method to produce a homozygous line within a short period (2-3 years) by doubling the haploid line generated through pollination of spring bread wheat F₁ with maize.

In this work, an analog front-end (AFE) circuit for Electrocardiogram (ECG) detection system has been designed, implemented, and investigated in an industry-standard Cadence simulation framework using advanced technology node of 45 nm. The AFE consists of an instrumentation amplifier, a Butterworth band-pass filter (with fifth-order low-pass and second-order high-pass sections), and a second-order notch filter- all are based on two-stage, Miller-compensated operational transconductance amplifiers (OTA). The OTAs have been designed employing the $g_m/I_D$ methodology. Both the pre-layout and post-layout simulation were carried out. The layout consumes an area of 0.0058 mm$^2$ without the resistors and capacitors. Analysis of various simulation results were carried out for the proposed AFE. The circuit demonstrates a post-layout bandwidth of 239 Hz with a variable gain between 44 to 58 dB, a notch depth of -56.4 dB at 50.1 Hz, a total harmonic distortion (THD) of -59.65 dB (less than 1\%), an input referred noise spectral density of $

Particulate Organic Carbon (POC) plays a crucial role in the marine carbon cycle, influencing carbon flux and many important ocean biogeochemical processes in the Bay of Bengal. The purpose of this study was to examine the seasonal and annual variability of POC in the Bay of Bengal (BoB) region and its correlation with Sea Surface Temperature (SST) and Chlorophyll-a (Chlor_a). This study uses level-3 POC, Chlor_a, and SST data from the Moderate Resolution Imaging Spectroradiometer (MODIS) Aqua satellite. The surface POC concentration in the Bay of Bengal declined at a rate of -1.30 mgm^-3y^-1 over a ten-year period (2003-12) and ranged from 86.48 mgm^-3 to 110.93 mgm^-3 with an average of (93.74±7.50 mgm^-3). Seasonally, the mean POC was highest (97.40 mgm^-3) during the post-monsoon (October-November) and lowest (79.36 mgm^-3) in the pre-monsoon (March-May). Seasons were observed to have statistically significant differences in POC concentration in the study area (F_(3,2155) = 6.298; p <0.05). A strong positive correlation between POC and Chlorophyll was observed whereas a week positive correlation between POC and SST was observed. POC was observed to be very prominent in post-monsoon (97.40 mgm^-3) and in northeast-monsoon (97.14 mgm^-3) and moderate to low in southwest (81.12 mgm^-3) and pre-monsoon (79.36 mgm^-3). The Bay of Bengal’s annual mean POC:Chlor_a ratio ranged from 97.56 mgm^-3 to 332.89 mgm^-3, indicating a significant impact of biological processes on POC composition. To see how POC fluctuation affects biogeochemical processes in the Bay of Bengal, deeper investigation is required.

Dehydration of hydrogen gas is one of the important steps in many industrial purposes thus, drying systems have been developed with high-efficiency and relative effect. In this article, the basic principles and design of a three-bed TSA (Temperature Swing Adsorption) dryer for dehydration operation of hydrogen gas drying are described in detail. The text commences with an in-depth explanation of the basic principles behind TSA technology such as adsorption and desorption mechanisms, thermodynamic considerations and material selection for adsorbents. This paper also deals with the detailed design of a three-bed TSA dryer, explaining about various fabricating details that influences both performance and total operability. The third part focuses the operational phase, and especially in cycle time, regeneration strategy and efficiency of energy. Advanced optimisation techniques are employed to lower energy consumption, increase throughput capacity and improve overall system. This detailed study will be of great help for engineers and investigators working on TSA systems design and optimization to dehydrate hydrogen gas, contributing towards the betterment in this important field dealing with industrial gas processing.

Alzheimer’s disease (AD) is one of the most prevailing neurodegenerative diseases, characterized by memory dysfunction and the presence of hyperphosphorylated tau and amyloid β (Aβ) aggregate in multiple brain regions, including the hippocampus and cortex. The exact etiology of AD has not yet been confirmed. However, epidemiological reports suggest that populations who were exposed to environmental hazards are more likely to develop AD than those who were not. Arsenic (As) is a naturally occurring environmental risk factor abundant in the Earth’s crust and human exposure to As predominantly occurs through drinking water. Convincing evidence suggests that As causes neurotoxicity and impairs memory and cognition although the hypothesis and molecular mechanism of As-associated pathobiology in AD are not clear yet. However, exposure to As and its metabolites leads to various pathogenic events such as oxidative stress, inflammation, mitochondrial dysfunctions, ER stress, apoptosis, impaired protein homeostasis, and abnormal calcium signaling. Evidence has indicated that As exposure induces alterations that coincide with most of the biochemical, pathological, and clinical developments of AD. Here, we overview existing literature to gain insights into the plausible mechanisms that underlie As-induced neurotoxicity and the subsequent neurological deficits in AD. Prospective strategies for the prevention and management of arsenic exposure and neurotoxicity have also been discussed.

Despite the expansion of financial institutions and proliferation of mobile financial services, reaching the unbanked and bringing them under formal financial services has become a policy concern in many developing countries. Due to the lack of financial accounts, unbanked people prefer informal, risky, and inconvenient mechanisms for receiving, sending and transferring money. Previous studies rely much on common intervention like no account maintenance and opening fees, easy documentation processes and money subsidies for opening financial accounts. This study aims to examine the impact of the motivational workshop on opening savings accounts through causality among the unbanked people in a setting where the respondents are unbanked despite having all the requirements and many institutional offers for opening savings accounts. We encouraged the unbanked people through a one-hour-long motivational workshop to open saving account. Based on our cross-sectional data and randomized controlled trial experiment among 505 unbanked Village Defense Party (VDP) members at Dhubil Union under Sirajganj in Bangladesh, we have the evidence that motivational workshop positively impacts opening ac-counts by 32.33 percent. However, the account opening rate differs in terms of respondent’s pref-erence for financial institutions. Our study also finds that unbanked people have the highest pref-erence for mobile financial services for opening accounts resulting in 15.33 percent. The result of the study has some policy implications for adopting effective strategies of financial access in many developing countries.

Zinc oxide (ZnO) as a semiconductor in its crystalline or amorphous form is still a promised material, especially under isobaric and isothermal ensembles. In this work, Parallel and Equilibrium Molecular Dynamics and DL_POLY_4 software are employed to predict the relationship between the behavior of ZnO chemical bonds and the phase transition literatures, using correlation function g(r) of Zn-Zn, Zn-O, and O-O pairs. Our system is composed of 5832 atoms of ZnO rocksalt structure (2916 atoms of Zn2+ and 2916 atoms of O2-), under the temperature of 300 (K) and the range of pressure 0-400 (GPa). The lengths of ZnO bonds, the standard error, standard deviation, the maximum of g(r), and the percentage of the variation of the bonds are analyzed. The interatomic interactions are modeled by the potential of Buckingham for short-range and Coulomb for long-range interactions. The calculations were run on the RAVEN Supercomputer of Cardiff University (UK). Our data are mostly in the vicinity of available information of bonds lengths; the rest can be deduced from the pressure of phase transition to use it as a new approach of phase transition confirmation. However, the rest of our results are still a prediction because of no results under extended pressure used in this work.

The permeation of dioxin-like pollutants, namely, chlorinated dibenzodioxins and dibenzofurans, through lipid membranes has been simulated using classic molecular dynamics (CMD) combined with the umbrella sampling approach. The most toxic forms of chlorinated dibenzodioxin and dibenzofuran, 2,3,7,8-tetrachloro-p-dibenzodioxin (TCDD) and 2,3,7,8-tetrachlorodibenzofuran (TCDF), and a dioleyl-phosphatidylcholine (DOPC) lipid membrane of 50 Å wide have been chosen for our study. The free energy profile shows the penetration process is largely favoured thermodynamically (DG≈-12 kcal/mol), with a progressively decrease of the free energy until reaching the energy minima at distances of 8Å and 9.5Å from the centre of the membrane for, respectively, TCDD and TCDF. At the centre of the membrane, both molecules display subtle local maxima with free energy differences of 0.5 and 1 kcal/mol with respect to the energy minima for TCDD and TCDF, respectively. Furthermore, the intermolecular interactions between the molecules and the lipid membrane have been characterized at the minima and the local maxima using hybrid quantum mechanics/molecular mechanics energy decomposition analysis (QM/MM-EDA). Total interaction energies of -17.5 and -16.5 kcal/mol have been found at the energy minima for TCDD and TCDF, respectively. In both cases, the dispersion forces govern the molecule-membrane interactions, no significant changes have been found at the local maxima, in agreement with the classical free energy profile. The small differences found in the results obtained for TCDD and TCDF point out the adsorption and diffusion processes through the cell membrane are not related to the different toxicity shown by these pollutants.

Arjunolic acid (AA) is a triterpenoid saponin majorly found in the Terminalia arjuna and is claimed to exert the cardiovascular protective effects as a phytomedicine. However, it is unclear how AA exerts the effects at the molecular level. Hence, this study used an in vitro model using lipopolysaccharide (LPS)-stimulated H9C2 and C2C12 myotubes to investigate the cardioprotective effects of arjunolic acid (AA) via MyD88-dependant TLR4 downstream signaling markers expression. The myotubes were developed by differentiating rat H9C2 and mouse C2C12 myoblast cells. The MTT viability assay was used to assess the cytotoxicity of AA. LPS induced in vitro cardiovascular disease model was developed in H9C2 and C2C12 myotubes. The treatment groups were designed such as control (untreated), LPS control, positive control (LPS+ pyrrolidine dithiocarbamate (PDTC)-25 µM), and treatment groups were co-treated with LPS and three doses of AA (50, 75, and 100 µM). The changes in the expression of TLR4 downstream signaling markers were evaluated through High Content Screening (HCS) and Western Blot (WB) analysis. The outcomes demonstrated that the expression of MyD88, MAPK, JNK, and NFκB markers were significantly upregulated in the LPS-treated groups compared to the untreated control. Evidently, the HCS analysis revealed that MyD88, NF-κB, p38, and JNK were significantly downregulated in the H9C2 myotube in the AA treated groups (50, 75, and 100 µM). For, the C2C12 myotube, the expression of NFκB was downregulated. TLR4 marker expression in H9C2 and C2C12 myotubes was subsequently decreased by AA treatment, suggesting possible cardioprotective effects of AA.

The Internet of Things (IoT) is a promising technology for sensing and monitoring the environment to reduce disaster impact. Energy is one of the major concerns for IoT devices, as sensors used in IoT devices are battery-operated. Thus, it is important to reduce energy consumption, especially during data transmission in disaster-adverse situations. Clustering-based communication helps reduce a node’s energy decay during data transmission and enhances the network’s lifetime. Many hybrid combination algorithms are proposed for clustering and the routing protocol to improve the network lifetime in disaster scenarios. However, the performance of these protocols is widely varied based on the underlying network configuration and the optimisation parameters considered. In this research, we have used the clustering parameters that are most relevant to disaster scenarios, such as the node’s residual energy, distance to sink, and network coverage. Then, we proposed a bio-inspired hybrid (BAO-PSO) algorithm where the Butterfly Optimisation Algorithm (BOA) is used for clustering and Particle Swarm Optimisation (PSO) is used for the routing protocol. The performance of the proposed algorithm is compared with the benchmark protocols LEACH, DEEC, PSO, PSO-GA, and PSO-HAS. Residual energy, network throughput, and network lifetime are considered performance matrices. The simulation result showed that the proposed algorithm increases network lifetime by 10%-20% by comparison with the benchmark algorithm.

Hydrogen is believed to be the principal domain of sustainable energy drive as an alternative to fossil fuels. Unlike the existing standards and knowledge for other fuels, the integrity of sealing and storage materials under the hydrogen environment is not comprehensively studied due to the comparatively new technology and lack of standard laboratory protocols. Typically, storage and polymer materials used as sealing experience degradation and damage in different ways over time in the exposure of hydrogen at different operating conditions, called aging. Improved understanding of the physical and chemical mechanism of degradation due to gaseous hydrogen atmosphere; helps to select and develop the materials best suited to carrier and sealing for respective applications. Damage to materials from aging is inevitable in high-pressure hydrogen gas exposure. This review discusses the mechanism of different categories of aging of storage and sealing materials under the hydrogen environment. Also, the article approaches discussing different laboratory test methods for each type of aging simulation. It covers the limitation of current research on determining material integrity through existing techniques of aging experiments and also explores the latest development. Important improvements are suggested in terms of materials development and testing procedures to meet the existing knowledge in the literature.

Conclusions: The quantitative method provides a large-scale overview of the biometry measurements of an entire practice. Image audits can then be focused on sonographers whose measurements are outliers, avoiding the time, complexity, and expense of auditing those whose measurements fall within the expected range. We encourage commercial software developers to include tools in their ultrasound reporting software to facilitate such quantitative review.

This research investigated the antihypertensive effects of tamarind products and compared their potentials based on their animal model’s data verified by molecular docking, multitarget interactions in network pharmacology, and dynamic simulation assays. The GC-MS characterized tamarind products were administered to the cholesterol-induced hypertensive Wistar albino rat models. Two-week-intervened animals were dissected to collect serum and organs which were respectively subjected to the analyses of hypertension-linked markers and tissue architectures. Lead biometabolites of tamarinds interacted with eight target receptors in molecular docking and dynamic simulation studies and they were tested for multitarget interactions using network pharmacological analyses. Results showed that serum alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP), C-reactive protein (CRP), Troponin I, and lipid profiles were maximally reinstated by the phenolic-enriched ripened sour over the sweet tamarind flesh extracts, but seed extracts had a smaller influence. Among the tamarind’s biometabolites, Gamma-sitosterol (ϒ-sitosterol) was found to be the best ligand in managing hypertension via the possible ligand-receptor interactions with the guanylate cyclase which displayed the best drug-likeliness through the highest binding energy -9.3 Kcal. Multitargeted interactions-based degree algorithm and phylogenetic tree of pathways showed 14 targeted genes, of which NR3C1, REN, PPARG, and CYP11B1 hub genes, were consistently modulated by the ϒ-sitosterol to reduce hypertension and related risk factors. The dynamic simulation study showed that the P-RMSD values of ϒ-sitosterol-guanylate cyclase were stable between 75.00 to 100.00 ns at the binding pocket. The findings demonstrate that ripened sour tamarind extract may be supplemented to be a more prospective antihypertensive target or nutraceuticals affirming through advanced preclinical and clinical studies.

(1) Background: Various cutaneous adverse drug reactions (ADRs) are observed with the development of mRNA COVID-19 vaccines. To gain insight into the clinicopathologic features, we analyzed the correlation of histological and clinical data in 48 patients with these ADRs.; (2) Methods: Single-center retrospective study in patients with ADRs post-mRNA COVID-19 vaccination (mRNA-1273 and BNT162b2 vaccines).; (3) Results: Distant generalized ADRs prevailed (91%), often appearing clinically as spongiotic dermatitis or maculo-papular exanthema. Histopathological analysis revealed spongiotic changes (46%) and dermal superficial perivascular lympho-histiocytic infiltrates (17%). Eosinophils were found in 66% of biopsies, neutrophils in 29%, and plasma cells only in 8% of biopsies. Most ADRs occurred post-second vaccine dose (44%). Histologically spongiotic changes were associated with clinical features of spongiotic dermatitis in only 50% and maculo-papular exanthema in the remaining patients. ADRs represented an aggravation of preexisting skin disease in 23% of patients. ADRs regressed within 28 days or less in 53% of patients and persisted beyond a month in the remaining patients.; (4) Conclusions: Our study demonstrates a diverse spectrum of generalized ADRs, revealing correlations between histology and clinical features but also instances of divergence. The majority of ADRs are self-limited with a few extending beyond a month.

The details of antigen-antibody interactions and the identification of epitopes are critical for the development of monoclonal antibody drugs. Ab42 is a native human-derived anti-CFH monoclonal antibody. In this study, the interaction between antigen pCFH and antibody (Ab42) was theoretically demonstrated by molecular docking and MD simulation, combined with free energy calculation and computational alanine scanning (CAS), and key amino acids and epitopes were identified. Experimental alanine scanning (EAS) was then carried out to verify the results of the calculation, and our results indicated that Ab42 antibody forms hydrogen bonds and interacts hydrophobically with pCFH through the Tyr315, Ser100, Gly33, and Tyr53 residues on its CDR, while the main pCFH epitopes are located at the six sites of Pro441, Ile442, Asp443, Asn444, Ile447, and Thr448. In conclusion, this study has explored the mechanism of antigen-antibody interaction from both theoretical and experimental aspects, and our results have important theoretical significance for the design and development of relevant antibody drugs.

Sustainable water resource management in Bangladesh's Gumti River Basin faces challenges from climate change, urbanization, and population growth. This study aimed to calibrate and validate the HEC-HMS model for the Gumti River to enhance flood prediction and water resource planning. The model was set up using precipitation, temperature, and discharge data from 2019-2021, with SRTM elevation data for catchment delineation. Manual calibration was performed for 2019-2020, followed by validation for 2021, using parameters such as Muskingum routing and SCS Curve Number. Model performance was evaluated using R², Nash-Sutcliffe efficiency (NSE), RSR, and PBIAS metrics. Results showed satisfactory to good performance, with R² values of 0.64 and 0.68 for calibration and validation, respectively. NSE values were within the satisfactory range, while PBIAS indicated very good performance with slight underestimation. The study concludes that the calibrated HEC-HMS model provides a reliable tool for simulating the Gumti River's hydrology, though there's room for improvement. Integration with flood frequency analysis, water quality monitoring, and climate change projections is recommended for comprehensive water resource management, alongside the implementation of Sustainable Water Resource Management principles and community engagement strategies.

(1) Background: Factors reported in literature associated with inappropriate prescribing of antimicrobials, such as physicians with less experience, uncertain diagnosis, and patient caregiver influences on physicians' decisions. Monitoring antimicrobial resistance is critical for identifying emerging resistance patterns, developing, and assessing the effectiveness of mitigation strategies. Improvement in prescribing `antimicrobials would minimize the risk of resistance and, consequently, improve patients' clinical and health outcomes. The purpose of the study is to delineate factors associated with antimicrobial resistance, describe the factors influencing prescriber’s choice during prescribing of antimicrobial, and examine factors related to consequences of inappropriate prescribing of antimicrobial. (2) Methods: Cross-sectional study conducted among healthcare providers (190) in six tertiary hospitals in the Eastern province of Saudi Arabia. The research panel has developed validated and piloted survey specific with closed-ended questions. A value of P &lt;0.05 was considered for statistical significance. All data analysis was performed using Statistical Package for Social Sciences (IBM SPSS version 23.0). (3) Results: 72.7% of the respondents have agreed that poor skills and knowledge are key factors that contribute to the inappropriate prescribing of antimicrobials. All the respondents acknowledged effectiveness and previous experience with the antimicrobial, and reading scientific materials (such as books, articles, and the internet) were key factors influencing physicians’ choice during antimicrobial prescribing. (4) Conclusion: The current study has identified comprehensive education and training needs for healthcare providers about antimicrobial resistance. Using antimicrobials unnecessarily, insufficient duration of antimicrobial use, and using broad spectrum antimicrobials, were reported to be common practices. Further, poor skills and knowledge were a key factor that contributed to the inappropriate use and overuse of antimicrobials and using antimicrobials without physician prescription (self-medication) were the key factors which contribute to AMR from participants’ perspectives. Furthermore, internal policy and guidelines are needed to ensure that the antimicrobials are prescribed in accordance with standard protocols and clinical guidelines.

A cross-sectional study was carried out to determine the prevalence of subclinical mastitis (SCM) among medium to large scale household dairy farms in southwestern district, Jhenaidah, Bangladesh during July to December 2019. A total of 78 (n=100) lactating cows from household dairy farms (N=32) having three or more dairy cows were selected randomly as sampled populations. Milk samples were screened for SCM by using Surf Field Mastitis Test (SFMT). The prevalence of SCM varied among farm level [71.9% (95% CI: 53.3-86.3)], individual animal level [67.9% (95% CI: 56.4-86.3)] and quarter level [29.5% (95% CI: 24.5-34.9)]. Descriptive statistics represented the farmers and farm demography, characteristics of the sampled population, and overall management feature. Random Effect Logistic Regression identified, Body Condition Score (BCS) [OR=3.8 and 2.9, at cows level and quarter level respectively (BCS-2 vs. BCS-≥3)], and breed [OR=5.1 and 2.9, at cows level and quarter level respectively (HF× Sahiwal vs. HF × Local)] as potential risk factors. This study shows that SCM is highly prevalent in the study area, which is a major threat to the dairy industry's production performance. Regular screening by SFMT, proper hygiene, improve the management system, and farmer’s awareness is required to control the disease.

Lassa virus (LASV) is responsible for a type of acute viral haemorrhagic fever referred to as Lassa fever. Lack of adequate treatment and preventive measures against LASV resulted in a high mortality rate in its endemic regions. In this study, a multi-epitope vaccine was designed using immunoinformatics as a prophylactic agent against the virus. Following a rigorous assessment, the vaccine was built using T-cell (N_CTL=8 and N_HTL=6) and B-cell (N_LBL=4) epitopes from each LASV-derived protein with suitable linkers and adjuvant. The physicochemistry, immunogenic potency and safeness of the designed vaccine (~68 kDa) were assessed. In addition, chosen CTL and HTL epitopes of our vaccine showed 97.37% worldwide population coverage. Besides, disulphide engineering also improved the stability of the chimeric vaccine. Molecular docking of our vaccine protein with toll-like receptor (TLR2) showed binding efficiency followed by dynamic simulation for stable interaction. Furthermore, higher levels of cell-mediated immunity and rapid antigen clearance were suggested by immune simulation and repeated-exposure simulation, respectively. Finally, the optimized codons were used in in silico cloning to ensure higher expression within E. coli K12 bacterium. With further assessment both in vitro and in vivo, we believe that our proposed peptide-vaccine would be potential immunogen against Lassa fever.

Since the first coronavirus patient was identified in Bangladesh on March 8, the most controversial issue is about the exact level of the infection in Bangladesh. Conformity with the population density the number of COVID-19 tests is inadequate. As the number of tests increases, so does the number of infections, making it difficult to predict the spread of COVID-19 in Bangladesh. In this case, the unplanned initiatives are particularly responsible in other for unplanned measures, lack of public awareness, and lack of proper knowledge. In this case, the Ministry of Health has made three major mistakes, three important features of the medical system in Bangladesh have been mentioned. It is more effective to prevent COVID-19 by isolating the infected person by further testing COVID-19 until effective treatment is available and to provide adequate and effective masks and personal protective equipment (PPE). In this case, the COVID-19 testing kit invention has received a good response in many countries of the world. This study focuses on the comprehensive data verification, selection, and evaluation of COVID-19 in Bangladesh and its implications for the future, what to do to address and prevent the COVID-19 challenge, and effective treatment against the coronavirus (COVID-19). It is hopeful that the discussion of the material mentioned in this research paper will help to strike a balance between the government, citizens, and experts which will be feasible in improving the current situation in COVID-19 Bangladesh and reducing its severity.

The fate of critically sick patients with infections in intensive care units (ICUs) is significantly influenced by antimicrobial resistance, which has become a serious concern in developing nations. This observational study was conducted at the IBN Sina Specialised Hospital in Dhaka, Bangladesh, over a 12-month period from January 2021 to December 2021, in order to track the pattern of antibiotic resistance among the patients admitted to the intensive care unit (ICU). Aspiration pneumonia (29%) and diabetes mellitus (24%), among 200 patients, were the most common main diagnoses. 65 samples (or 26%) of the 250 samples had 85 bacteria identified from them. Urine (14.12%) and tracheal aspirate (64.71%) were the most frequently found sites of infection. In the sample from the tracheal aspirate, Pseudomonas spp. (30.59%), Escherichia coli (24.71%), Acinetobacter spp. (20%), and Klebsiella spp. (14.12) were the most frequently isolated microorganisms. The following antibiotics were shown to have the highest overall patterns of resistance: levofloxacin (68.24), amikacin (64.71), meropenem (49.41), ceftazidime (75.29), ciprofloxacin (78.82), and gentamicin (82.35). The most effective antibiotic against Klebsiella species was meropenem (64.61%), while Acinetobacter species were mostly susceptible to cotrimoxazole (64.67%) and piperacillin + tazobactam (60.50%). Most susceptible to netilmicin (70.48%) and meropenem (49.32%) were Escherichia coli, while Pseudomonas spp. were mostly responsive to colistin (55.14%) and netilmicin (52.25%). Antibiotic resistance is common among intensive care unit (ICU) patients, and most isolated microbes have resistance to traditional medicines.

Dried blood spot (DBS) testing on confetti is one of the most common methods used to collect and extract DNA from field samples for molecular epidemiology of malaria studies. Here, we investigated whether ethanol or other solutions used to clean scissors are a source of sample contamination. DBS were prepared from 3 drops of blood from two Plasmodium falciparum cultures spotted on confetti, and 3 solutions (water, ethanol and DNase) were used to clean scissors between spots during DNA extraction. For each cleaning solution, two blank confetti were used as negative controls. Samples were analyzed by PCR-based genotyping of merozoite surface proteins 1 & 2 (msp-1 and msp-2), and P. falciparum chloroquine resistance transporter (Pfcrt). A total of 15 samples were analyzed. Based on msp-1 and msp-2 amplification, P. falciparum was detected on blank confetti when scissors were washed with ethanol. Based on Pfcrt amplification, DNA of P. falciparum was detected on blank confetti when scissors were cleaned with ethanol or water. No P. falciparum genes were detected on blank confetti when scissors were cleaned with DNase. Scissors cleaned with DNase prevented cross-contamination between samples during processing of dried blood spots, whereas ethanol (which is commonly used) fails to avert cross-contamination.

This research aimed to figure out the applications of HbA1c protein and HbA1 gene as the prognostic biomarkers for assessing the risks of different cancers among male T2D patients in Bangladesh considering their serological and oncoinformatic parameters. Depending on the concentrations of HbA1c (%) of the T2D patients (n=300), their individual FBS (mmol/L); THABF (mmol/L); creatinine (mg/dl); SC (mg/dl); STGs (mg/dl); HDLC (mg/dl); and LDLC (mg/dl) were estimated. The values of the patients were compared with the control (n=60) group as the serological analysis. Besides, HbA1 gene (encoding hBA1c protein) overexpression and promotor methylation responsible for BLCA, BRCA, CHOL, COAD, LUAD, LUSC, PAAD, and PRAD cancers in the male T2D patients were profiled as the oncoinformatic parameters based on the sample types; caner stages; racial footprints; gender; age; nodal metastasis; p53 methylations; pancreatitis; diabetes status; smoking behaviors; and overall/disease-free survivability. Finally, the ‘HbA1 gene strings’ responsible for genetic coexpression; endophytic vesicle regulation; antioxidant regulation; oxygen species metabolic regulation; and gene-mediated response to the reactive oxygen molecules were studied comprehensively. A strong correlation between BMI and FBS was observed in both the patients and the control (P<0.0001). Similarly, the values of FBS, THABF, and creatinine resulted in equal significance (P<0.0001) as compared to the HbA1c concentrations of all the T2D and control individuals. The SC, STGs, HDLC, and LDLC concentrations regulated ardently in both the control (P<0.0001), and patients group (P<0.0001), while HbA1c ranged from 3.8-5.8%, and 5.11-15.8% respectively. HbA1 gene is found downregulating with cancer progressed in most of the oncoinformatic parameters. According to the DA, CS, EI, CE, PC, NC, GF, H, and AT profiles; the HbA1 gene interacts with 8 other genes responsible for creating a protein cluster comprising- AHSP, HBA1, HBA2, HBB, HBD, HBE1, HBG2, RPS12, and RPS19 proteins for cancer formation. To recapitulate, HbA1c protein and HbA1 gene can be used as the prognostic serological and molecular biomarkers respectively for determining the risks of cancers among male chronic T2D patients.

Alkaloids are the most diversified nitrogen-containing secondary metabolites having antioxi-dant, and antimicrobial properties and are extensively used in pharmaceuticals to treat different types of cancer. Nicotiana serves as a reservoir of anticancer alkaloids and is also used as a model plant for the de novo synthesis of various anti-cancer molecules through genetic engineering. Up to 4% of the total dry weight of Nicotiana was found to be composed of alkaloids where nicotine, nornicotine, anatabine, and anabasine are reported as the dominant alkaloids. And, among the alkaloids present in Nicotiana, β-carboline (Harmane and Norharmane), Kynurenines are found to show anti-tumor effects, especially in the case of colon and breast cancer. Creating new or shunting of existing biosynthesis pathways in different species of Nicotiana resulted in de novo or increased synthesis of different anti-tumor molecules or their derivatives or precursors includ-ing Taxadiane (~22.5 µg/g), Artemisinin (~120 μg/g), Parthenolide (~2.05 ng/g), Costunolide (~60 ng/g), Etoposide (~1 mg/g), Crocin (~400 µg/g), Catharanthine (~60 ng/g), Tabersonine (~10 ng/g), Strictosidine (~0.23 mg/g), etc. Enrich precursor pool especially Dimethylallyl Diphos-phate (DMAPP) and down-regulating of other bi-product pathways, compartmentalization or metabolic shunting, or organelle-specific reconstitution of the precursor pool might trigger the enhanced accumulation of the targeted anticancer alkaloid in Nicotiana.

Beyond their significant contribution to the dietary and industrial supplies, marine algae are considered to be a potential source of some unique metabolites with diverse health benefits. The pharmacological properties, such as antioxidant, anti-inflammatory, cholesterol homeostasis, protein clearance and anti-amyloidogenic potentials of algal metabolites endorse their protective efficacy against oxidative stress, neuroinflammation, mitochondrial dysfunction, and impaired proteostasis which are known to be implicated in the pathophysiology of neurodegenerative disorders and the associated complications after cerebral ischemia and brain injuries. As was evident in various preclinical studies, algal compounds conferred neuroprotection against a wide range of neurotoxic stressors, such as oxygen/glucose deprivation, hydrogen peroxide, glutamate, amyloid β, or 1-methyl-4-phenylpyridinium (MPP+) and, therefore, hold therapeutic promise for brain disorders. While a significant number of algal compounds with promising neuroprotective capacity have been identified over the last decades, a few of them have had access to clinical trials. However, the recent approval of an algal oligosaccharide, sodium oligomannate, for the treatment of Alzheimer's disease enlightened the future of marine algae-based drug discovery. In this review, we briefly outline the pathophysiology of neurodegenerative diseases and brain injuries for identifying the targets of pharmacological intervention, and then review the literature on the neuroprotective potentials of algal compounds along with the underlying pharmacological mechanism, and present an appraisal on the recent therapeutic advances. We also propose a rational strategy to facilitate algal metabolites-based drug development.

The need for integrated high-frequency systems has increased significantly, leading to the development of efficient antennas operating in the 0.1-10 terahertz (THz) range. Using graphene as the conducting 2D material and hexagonal boron nitride (hBN) as the dielectric substrate, this research effort examines the design and performance evaluation of a THz band antenna functioning on supporting nanotechnology. The researchers contrasted the system’s performance with the 6G wireless network requirements after analyzing the antenna performance, radiation patterns, and impedance matching. According to this research, graphene, along with hBN can enhance antenna performance overall in the THz band and open pathways for advanced communication. The application of the designed antenna in a 6G wireless network will be tested through um MIMO configuration to achieve a higher data rate.

Anemia and thyroid disorders are global health issues that affect all ages but are more apparent in women. In this case, some serological components responsible for IDA and TSH disorders in women have been found actively regulated through a complex steroidal-calcitriol mediated pathway. This research has been investigated the correlation between Calcitriol and the serological components responsible for IDA and TSH disorders in childbearing and non-child-bearing women of different health conditions. Experimental sampling from 452 women suffering from both IDA and TSH disorders were taken, aged between 0 and 70 years. Serological parameters, such as iron, total iron-binding capacity and ferritin, were assessed for IDA profiling, whereas thyroid-stimulating hormone and free thyroxin were for TSH profiling based on the individual’s serum calcitriol status. The resulted serological data were interpreted using sophisticated computer programming language and algorithms for quantitative biochemical analysis. The study resulted in a significant correlation between FT4 and Calcitriol (P<0.0001) for all age groups. TSH also showed strong interactions with the fluctuation of calcitriol level (P<0.0001), except for the children aged below 10 years (P<0.063). The iron, TIBC, TSH, and FT4 showed phenomenal regulation with the steroidal-calcitriol concentration for congenital patients. Unlike the others, ferritin has a substantial connection with Calcitriol (P<0.0064) fluctuation in the serum. To ratify, the concentrations of TSH, FT4, iron, TIBC, and ferritin were found to be significantly interconnected in terms of serum calcitriol level in women suffering from IDA and TSH disorders simultaneously. To understand the accuracy and efficacy of the Calcitriol in IDA and TSH disorders, some other inflammatory markers and parathyroid hormone analysis are need in future studies, besides a large number of samples.

The two combined technologies WPT and AI still have huge prospects for several industries such as consumer electronics and industry. This paper looks at the recent developments in WPT, particularly concerning AI-improved efficiency, range, and reliability. AI-driven also works to control power, manage device alignment, and test when maintenance is necessary, this makes powering smarter and more efficient. Accuracy is given by deploying machine learning and computer vision, and on the other hand, the maintenance procedure is done through predictions. Furthermore, the ability of the management system to include the use of AI in power regulation enables the control of consumption based on the load. In this study, the positive future effect of AI is discussed concerning improvements in WPT technologies, which is paramount in subsequent applications. Based on the results, it is essential to continue the investigation of the topic within this interdisciplinary science to advance existing problems and discover novel possibilities for evolution. Data based on experiments shows a significant improvement in the efficiency of information transfer where AI is used with rates up to 25% higher than those using the traditional ways. Additionally, advanced maintenance forecasting algorithms improve system availability by cutting down on 30% of the downtimes when applied in real-life applications of AI technology. The study also looks at the possibilities of the outlook to the future including emergence of the distributed artificial intelligence for autonomous WPT network, and additional potential of quantum computing for the use to improve the algorithm. This indicates that there is a new era for the convergence of WPT and AI to enhance the progress of power transfer system in conditions of elegant, efficient, and robust.

This article titled "AI and IoT in Automation and Security: A Vision for Next Generation Applications," explored the implications of marrying IoT with AI in the realms of automation and security; this piece goes further into what that entails. In this paper, we present innovative application descriptions arising from this technology convergence and its future-generation applications. We found that AI brings strong cyber security, predictive maintenance, and decision-making capabilities to the table due to its advanced algorithms and machine learning models. IoT has the potential to allow businesses to extract and generate big data, automate processes, and monitor in real-time thousands and even millions of businesses at once. For now, we believe some of the possible main conclusions will be that the smart city, stand-alone systems, and user experience will be quite consumer-friendly. Importantly, the study also assessed facets such as data protection, system interoperability, and a few others. Our vision underscores the essential of a strong structure to connect the full latent of AI and IoT, finally aiming to create more capable, protected, and approachable environments. Significant results include achieving 95.8% accuracy in anomaly detection and 93.4% accuracy in predictive maintenance. The showcasing results efficacy of AI models to enhance system reliability as well as operational efficiency. Vigorous encryption protocols performance ensures data security hence addressing issues of privacy. These culminations underscore the transformative potential of AI-IoT integration in next-generation automation and security applications.