Accurate evaluation of health status of lithium-ion batteries must be deemed as of great significance, insofar as utility and safety of batteries are of concern. Lithium plating, in particular, is notoriously known to be a chemical reaction that can cause deterioration in, or even fatal hazards to, the health of lithium-ion batteries. Electrochemical impedance spectroscopy (EIS), which has distinct advantages such as fast or non-destructive over its competitors, suffices in detecting lithium plating and thus has been attracting increasing attention in the field of battery management, but its ability of assessing quantitatively the degree of lithium plating remains largely unexplored hitherto. On this point, this work seeks to narrow that gap, by proposing an EIS-based method that can quantify the degree of lithium plating. The core conception is to eventually circumvent the reliance on state-of-health measurement, and use instead the impedance spectrum, to acquire an estimate on battery capacity loss. To do so, the effects of solid electrolyte interphase formation and lithium plating on battery capacity must be first decoupled, so that the mass of lithium plating can be quantified. Then, based on an impedance spectrum measurement, the parameters of the fractional equivalent circuit model (ECM) of the battery can be identified. These fractional ECM parameters are received as inputs by an artificial neural network, which is tasked to establish a correspondence between the model parameters and the mass of lithium plating. The empirical part of the work revolves around the data collected from an aging experiment, and the validity of the proposed method is truthfully attested by dismantling the batteries, which is otherwise not needed during the actual uptake of the method.

An analytical method was established by HPLC-DAD-ELSD with C18-NH2 column tandem for the simultaneous determination of hydrophobic components atractylenolide I, II, III, atractylone and hydrophilic compounds glucose, fructose and sucrose in the dried rhizome of Atractylodes macrocephala Koidz (a natural raw material for health foods, Bai-Zhu aka. in Chinese). The method combines different separation capabilities of reversed-phase liquid chromatography and hydrophilic interaction liquid chromatography, can provide a new choice for the simultaneous determination of hydrophilic and hydrophobic compounds in traditional Chinese medicines and health foods. It provided a reference method for the quality control of Bai-Zhu. The results showed that the linear correlation coefficients of the established column tandem chromatographic method were all greater than 0.9990, the relative standard deviation was 0.1%-2.8%, and the average recovery was 96.7%-103.1%. The contents of atractylenolide I, II, III, atractylone, fructose, glucose, and sucrose in 17 batches of Baizhu were 172.3-759.8 μg/g, 201.4-612.8 μg/g, 160.3-534.2 μg/g, 541.4-8723.1 μg/g, 6.9-89.7 mg/g, 0.7-7.9 mg/g, and 1.2-21.0 mg/g, respectively.

In this paper, we obtain the existence and uniqueness theorem for solutions of Caputo type fractional stochastic delay differential systems (FSDDSs) with Poisson jumps by utilizing delayed perturbation of Mittag-Leffler function. Moreover, by using Burkholder-Davis-Gundy's inequality, Doob's martingale inequality and Holder inequality, we prove that the solution of the averaged FSDDSs converges to that of the standard FSDDSs in the sense of Lp. Some known results in the literature are extended.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

Ecological stoichiometry is an important index to reflect ecological interaction and the balance of various elements in ecological processes. At present, the stoichiometric spatial distribution of soil carbon (C), nitrogen (N), phosphorus (P) and potassium (K) in farmland and grassland of Inner Mongolia and its influencing factors are still unclear. In this study, the spatial distribution of soil nutrient content and stoichiometry and the effects of environmental factors on soil C:N:P:K stoichiometry were analyzed under different land use patterns in four agro-pastoral areas. The results showed that there was a geographical gradient in the ecological stoichiometric relationship between farmland and grassland. RCN, RCP, RCK, RNP and RNK showed an "N" distribution from west to east, while RPK showed a "V" distribution. The difference in spatial distribution was more significant than the difference in land use pattern. The ecological stoichiometric relationship of grassland was mainly affected by the content of C and N, and was related to the similarity of soil properties. The field ecological stoichiometry was mainly affected by the content of nitrogen and phosphorus, and had a great relationship with fertilization. The effects of MAT and MAP on soil ecological stoichiometry were related to the inter-regional environmental heterogeneity. The influence of MAP on farmland and MAT on grassland was more significant. It was of great significance for field management according to local conditions, rational utilization of land resources and sustainable development of agriculture to clarify the ecological stoichiometric characteristics of farmland and grassland in agro-pastoral ecotone.

According to the requirement of 20kg load of casting barrel, we design a three-dimensional model of the robot and analyze the three stages of liquid level change in the casting barrel during the casting process. Through the analysis, it is determined that the time and angle function is an implicit function, and it is impossible to find the analytical expression of time about angle. The kinetic function of the casting barrel is simulated by MATLAB, and it is found that the function image has mutation points, and when the original function is fitted and approximated by fifth-degree polynomial interpolation, the fifth-degree polynomial function image of the time versus the angular acceleration has a large amplitude of oscillation, especially the mutation points. A PID algorithm based on the discretization of the time and acceleration function is introduced for correction, and the results show that this method effectively reduces the oscillation amplitude of the image and improves the coincidence with the original function.

Aim: To analysis the relationship between healthy adults right ventricular diameter (RVD) and geographical factors. Location: China’s 22 provinces, municipalities and autonomous regions. Methods: Using correlation analysis the relationship between RVD and nine geographic factors, build predictive models by factor analysis. Results: There is significant correlation between RVD and geographical factors, and the annual average temperature is most relevant geographical factors, a predictive model was built by factor analysis: Ŷ = 19.46 + 0.0007072X1 + 0.001034X2 -0.05412X3 -0.001405X4 -0.0006351X5 + 0.02903X6 + 0.01243X7 -0.01033X8 + 0.03816X9 ± 0.63. Then using Kriging interpolation interpolate the geographical distribution of Chinese healthy adult right ventricular diameter reference value in ArcGIS software. Main Conclusion: If geographic factors can be derived in anywhere of China, RVD can be calculated by the model, you can also get RVD from geographical distribution.

Benzimidazole fungicides are a class of highly effective, low-toxicity, systemic broad-spectrum fungicides developed in the 1960s and 1970s, based on the fungicidal activity of the benzimidazole ring structure. They exhibit biological activities including anticancer, antibacterial, and antiparasitic effects. Due to their particularly outstanding antibacterial properties, they are widely used in agriculture to prevent and control various plant diseases caused by fungi. The main products of benzimidazole fungicides include benomyl, carbendazim, thiabendazole, albendazole, thiophanate, thiophanate-methyl, fuberidazole, carbamic acid, and carbendazim salicylate. This article mainly reviews the physicochemical properties, toxicological properties, and disease control efficacy, and pesticide residue and detection technologies of the aforementioned nine benzimidazole fungicides and their main metabolite (2-aminobenzimidazole). On this basis, a brief outlook on the future research directions of benzimidazole fungicides is presented.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

Dragon fruit (Hylocereus polyrhizus) constitutes an important economic industry in Guizhou Province, China; however, in recent years, stem rot in this region has become increasingly severe. Moreover, the pathogens responsible for stem rot in Guizhou and their sensitivity to fungicides remain elusive. Therefore, in this study, we aimed to determine the causative pathogens of stem rot in this region and analyze their sensitivity to fungicides. Twenty-four isolates were obtained from diseased tissues, from which H-4 and H-5 were selected and confirmed as pathogens. Based on the morphological characteristics of macroconidia, microconidia, and colony morphology, the polygenic phylogenetic tree constructed using internal transcribed spacer, elongation factor 1-alpha, and retinol-binding protein-2 gene fragments, along with carbon source metabolism using FF microplates, the two pathogens were identified as Fusarium oxysporum and F. concentricum respectively. In addition, the in vitro toxicity of eight fungicides against both pathogens were measured based on mycelium growth rate. The results showed that 75% trifloxystrobin·tebuconazole exhibited the strongest inhibitory effect on both isolates, with concentration for 50% of maximum effect values of 0.1262 µg/mL and 0.1385 µg/mL, respectively. This study identified two Fusarium spp. as the causative pathogens of stem rot in dragon fruit, with F. concentricum being reported for the first time, and demonstrated the best fungicide for them. These findings hold significant potential for guiding the effective treatment of stem rot in dragon fruit in Guizhou, China.

Project portfolio configuration (PPC) is an important approach to maintain the sustainable development of enterprises and achieve organizations’ strategy. However, the synergetic efficacy of PPC which determines the degree of the project's strategic objectives achieved is a fuzzy problem and hard to be measured. To solve this problem, this paper takes the data envelopment analysis (DEA) as the tool to measure the efficacy of PPC under deterministic conditions. First, a portfolio evaluation index system which takes financial indicators and non-financial indicators into consideration is developed based on the review of the literature; Second, an evaluation model based on DEA is built to reduce the number of decision making-unit with the perspective of synergetic theory; Then, a computational experiment is studied to verify the feasibility of this proposed model. The results of this computational experiment show that this model can effectively narrow scope of decision-making, improve the decision-making level and provide a reference to decide the DEA effective project portfolio decision-making unit. To our knowledge, this study is the first time to apply the notion of synergetic efficacy and DEA to the PPC domain. It is hoped that this paper may shed lights on any further study about PPC and enterprise competitiveness of sustainable development.

To reveal the influence of variables such as entrepreneurial learning, entrepreneurial inspiration, and incubation resources on students' entrepreneurial intentions in vocational colleges, this study took vocational colleges in Zhejiang Province, a province with a strong entrepreneurial climate in China, as an example. The study used a questionnaire to obtain data, and 614 valid questionnaires were collected from seven vocational colleges. The study divided entrepreneurship education into three dimensions: entrepreneurial learning, entrepreneurial inspiration, and incubation resources, and used structural equation modeling to investigate the influence of entrepreneurship education on entrepreneurial intentions while introducing entrepreneurial efficacy as a mediating variable to examine the influence mechanism of entrepreneurship education on entrepreneurial intentions of higher education students. The results showed that entrepreneurial learning, entrepreneurial inspiration, incubation resources, and entrepreneurial efficacy were all significantly and positively correlated with entrepreneurial intentions and that entrepreneurial efficacy mediated between the two dimensions of entrepreneurship education (entrepreneurial learning and entrepreneurial inspiration) and entrepreneurial intentions. Therefore, to enhance the effectiveness of entrepreneurship education in vocational institutions, we should stimulate students' sense of entrepreneurial efficacy, strengthen their entrepreneurial learning and inspire them to start their businesses. In turn, university incubation resources can be developed and utilized to enhance students' entrepreneurial confidence and intentions.

Cotton fiber, a crucial and sustainable resource for global textile production, undergoes a complex five-stage developmental process, encompassing initiation, elongation, transition, secondary cell wall biosynthesis, and maturation. These elongated single-cell fibers originate from the outer ovule epidermis. The development of cotton fibers involves intricate changes in gene expression and physiological processes, resulting in a nearly pure cellulose product vital for the global cotton industry. Decoding genes associated with fiber development enhances our understanding of cotton fiber mechanisms and facilitates the cultivation of varieties with enhanced quality. In recent decades, advanced omics approaches, including genomics, transcriptomics, and proteomics, have played a pivotal role in identifying genes and gene products linked to cotton fiber development, including the MYB transcription factor family which coordinates cotton fiber development. Molecular studies have revealed transcription factors like MYB, WRKY, Homeodomain Leucine Zipper (HD-ZIP) and basic Helix-Loop-Helix (bHLH) influencing fiber initiation and elongation. The intricate interplay of phytohormones like auxin, gibberellic acid (GA), brassinosteroid (BR), jasmonic acid (JA), ethylene, abscisic acid (ABA), and cytokinin is explored, providing a comprehensive perspective on shaping cotton fibers. Numerous candidate genes and cellular processes affecting various aspects of fiber development hold promise for genetic engineering or marker-assisted breeding to improve fiber quality. This review presents a comprehensive overview of key achievements in cotton molecular biology, with a specific emphasis on recent advancements in understanding transcription factors and phytohormones involved in cotton fiber initiation and elongation.

Individuals are pupils of society, and students represent individuals within the societal context. It is the noble aspiration of every educator to cultivate students with well-rounded personalities for the benefit of society. School curricula are instrumental in shaping the children who will, in turn, shape the future of society, and it is posited that students with well-rounded personalities are invariably those who embody love. The challenge lies in how to enable children to possess, retain, extend, refine, and be filled with love—a task necessitating the collaborative and synergetic efforts of both the educational and social systems to achieve a societal milestone. Pedagogy of love focuses on nurturing the capacity for love within students, who, through self-awareness of their indoctrination in love, transform techniques of self-love into capabilities of love for others. This process continuously generates the energy of love within social relations, thereby fostering social production, improving the relations of production, and enhancing the creative capacities, vitality, and welfare of a socialist society's wealth and capital accumulation.

This article mainly proposes the point of view that financial literacy curriculum aims to make kinds of people, to make people with financial creativity of resource integration thinking and continuous ‘to conscience’ of morality, which is cultivate a way of thinking that can maximize benefits through the use of resource integration and constantly ‘to conscience’ to achieve goals for participants in financial structures with balanced interests. In this sense, this article argues that financial literacy is to make kinds of people with a financial mindset and constantly strengthen ‘to conscience’ through uniting of knowledge and action to achieve human well-being and benign operation of society. In this sense, this article attempts to determine what is really taught in financial literacy education in terms of curriculum theory. That is to improve creativity by cultivating financial thinking with constant ‘to conscience’. The views of this paper provide a new way of thinking about financial literacy education assessment. This changes the evaluation criteria of financial literacy education from the result-oriented of wealth growth to the process-oriented of financial creativity growth, trying to move the criticism of financial literacy education curriculum and evaluation from controversy to unity.

In recent years, video anomaly detection technology , which can intelligently analyze massive video and quickly find abnormal phenomena, has attracted extensive attention with the wide application of video surveillance technology . To address the complex and diverse problem of abnormal human behavior detection in surveillance videos, a surveillance video abnormal behavior detection and localization supervised method based on the deep network model and the traditional method is proposed. Specifically, we combined AGMM and YOLACT methods to obtain more accurate foreground information by fusing the foreground maps extracted by each technique. To further improve the accuracy , we use the PWC-Net technique to extract features of the foreground images and input them into an anomaly classification model for classification. The proposed method effectively detects and locates the abnormal behavior in the monitoring scene. In addition to the aforementioned methods, this paper also employs YOLOV5 and DeepSORT networks for object detection and tracking in the video, which allows us to track the detected objects for better understanding of the scene in the video. Experiments on the UCSD benchmark dataset and the comparison with state-of-the-art schemes prove the advantages of our method.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

In the paper, the authors survey integral representations of the Catalan numbers and the Catalan–Qi function, discuss equivalent relations between these integral representations, supply alternative and new proofs of several integral representations, collect applications of some integral representations, and present sums of several power series whose coefficients involve the Catalan numbers.

In the paper, the authors find two explicit formulas and recover a recursive formula for the generalized Motzkin numbers. Consequently, the authors deduce two explicit formulas and a recursive formula for the Motzkin numbers, the Catalan numbers, and the restricted hexagonal numbers respectively.

This study investigates the possible mechanisms related to the wide range of relative humidity in cirrus clouds (RHi). Under the closed adiabatic assumption, the impacts of vertical motion and ice crystal deposition/sublimation on RHi are investigated through in situ observations and parcel model simulations. Vertical motion is an active external force that changes the RHi, and ice crystal deposition/sublimation plays a role in mitigating the change in RHi. They are the two most important mechanisms involved in controlling the RHi fluctuation during cirrus evolution and could well explain the wide range of RHi in wave-related cirrus clouds. Furthermore, a comparison of cloud statistical characteristics from both observations and simulations shows that a very low value (e.g., 0.001) for the water vapor ice deposition coefficient is highly unlikely.

In this study, we investigate the behavior of randomly moving particles with a defined average energy, focusing on their biased motion around a specific point. These particles' velocity magnitudes follow a Maxwell distribution with a specific scale parameter. Our analysis derives the stochastic rotation rules for these particles and introduces the Ito equation conditions for biased stochastic rotation at a given curl value. We also consider the special relativistic-like effects in this context. The findings are validated through a representative example.

This study presents a novel approach for quantifying the dynamics of monthly hydraulic geometry relationships in the Jingjiang reach of the Yangtze River by integrating leaf area index (LAI) data as an indicator of riparian vegetation. A comprehensive system of ordinary differential equations (ODEs) couples traditional power-law hydraulic geometry equations with LAI, capturing the influence of erosion control on channel morphology. The periodic delayed response theory and automatic differentiation techniques are employed to enhance the modeling framework's capabilities. Calibration and verification demonstrate the models' effectiveness in capturing overall trends in discharge, width, and depth dynamics, outperforming traditional constant-parameter approaches. However, model predictive abilities are limited under extreme climate conditions due to training on normal climate data. Key assumptions, including the periodic delayed response theory's neglect of peak discharges, simplified representation of artificial cut-offs, and reliance on remotely sensed data with limited local validation, introduce uncertainties. The proposed modeling framework shows potential for broader application to other river systems with appropriate adjustments. Future research could incorporate additional environmental factors, integrate models across scales, couple with advanced simulation techniques, and expand stability assessments beyond the riverbed index. By addressing related challenges, this integrated approach lays a foundation for enhancing understanding of river morphodynamics and channel stability.

In the paper, the authors establish two identities to express the generating function of the Chebyshev polynomials of the second kind and its higher order derivatives in terms of the generating function and its derivatives each other, deduce an explicit formula and an identities for the Chebyshev polynomials of the second kind, derive the inverse of an integer, unit, and lower triangular matrix, present several identities of the Catalan numbers, and give some remarks on the closely related results including connections of the Catalan numbers respectively with the Chebyshev polynomials, the central Delannoy numbers, and the Fibonacci polynomials.

Heptanuclear {GdIII7} (complex 1) and tetradecanuclear {GdIII14} (complex 2) have been synthesized using a Rhodamine 6G ligand HL (Rhodamine 6G salicylaldehyde hydrazone) and characterized. Complex 1 has a rare disc-shaped structure, where the central Gd ion was connected to the peripheral six GdIII ions via CH3O-/μ3-OH- bridges. Complex 2 has an unexpected three-layer double sandwich structure with a rare μ6-O2- ion in the center of the cluster. Magnetic studies revealed that complex 1 exhibits a magnetic entropy change of 17.4 J kg−1 K−1 at 3 K and 5 T. On the other hand, complex 2 shows a higher magnetic entropy change of 22.3 J kg−1 K−1 at 2 K and 5 T.

Tumor-associated macrophages (TAMs) play critical roles in the tumor microenvironment (TME), where they are recruited by signals released by cancer cells. Although they have great potential as therapeutic targets for cancer treatment, the dual roles of TAMs in promoting or inhibiting tumor growth, invasion, and metastasis make their function in cancer progression complex. In this review, we provide an overview of the current understanding of TAMs, including their phenotypic diversity, regulatory signaling pathways, and interactions with other cells in the TME. We also discuss the challenges related to the standard isolation protocols of TAMs, inconsistent research results, and translation of TAM knowledge into clinical applications. Additionally, we review the status of clinical trials involving TAMs and potential strategies to overcome the limitations. The future direction of TAM research should focus on developing more targeted therapies that specifically regulate TAM function and non-invasive methods for monitoring TAM activity in cancer patients. A comprehensive understanding of the complex role of TAMs in cancer may lead to the development of more effective treatments and improved outcomes for cancer patients.

Aim: This study aimed to investigate the association between periampullary diverticulum (PAD) and difficult biliary cannulation, as well as to evaluate the impact of different types of PAD on the cannulation success rate and adverse events. Methods: A total of 636 patients who underwent endoscopic retrograde cholangiopancreatography (ERCP) during the study period were prospectively studied and divided into two groups based on the presence or absence of PAD. In group A, 126 patients had PAD compared with 510 patients in group B without PAD. The primary outcome measurements were ERCP procedures time, selective cannulation techniques, and cannulation difficulty in addition to cannulation success rate and ERCP-related adverse events. The difficult cannulation was analyzed using logistic regression considering age, co-morbidities, the presence of PAD types, and indications as independent factors. Results: The average cohort age was 65.30±16.67 years, and 52.7% were male. Significant higher rates of choledocholithiasis, cholangitis, and biliary pancreatitis were reported in the group of PAD (p<0.05). Successful selective cannulation was achieved in 97.6% in group A and 95.3% in group B (p>0.05). The cannulation time was significantly longer in the presence of PAD (5.1 min, vs. 4.09 min, p<0.05). There was no significant difference in the rate of overall adverse events and post ERCP pancreatic PEP. Conclusion: The presence of PAD did not affect the duration or success of the ERCP procedure. Furthermore, it was associated with longer cannulation time and increase in the cannulation difficulty, especially with PAD type 1.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

CNN-based methods have dominated the field of aerial scene classification for the past few years. While achieving remarkable success, CNN-based methods suffer from excessive parameters and notoriously rely on large amounts of training data. In this work, we introduce few-shot learning to the aerial scene classification problem. Few-shot learning aims to learn a model on base-set that can quickly adapt to unseen categories in novel-set, using only a few labeled samples. To this end, we proposed a meta-learning method for few-shot classification of aerial scene images. First, we train a feature extractor on all base categories to learn a representation of inputs. Then in the meta-training stage, the classifier is optimized in the metric space by cosine distance with a learnable scale parameter. At last, in the meta-testing stage, the query sample in the unseen category is predicted by the adapted classifier given a few support samples. We conduct extensive experiments on two challenging datasets: NWPU-RESISC45 and RSD46-WHU. The experimental results show that our method yields state-of-the-art performance. Furthermore, several ablation experiments are conducted to investigate the effects of dataset scale, the impact of different metrics and the number of support shots; the experiment results confirm that our model is specifically effective in few-shot settings.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

Under the development mode of deep blending of emerging technologies, major projects are important for enhancing China's comprehensive national strength and independent innovation capability. Based on the social benefits of major projects, and considering the influence of reputation factors, an evolutionary game model composed of a general contractor and subcontractor of major projects is established. This paper studies the influence of various factors including the income distribution coefficient of collaborative innovation, and MATLAB simulation software is analyzed the influence of factors on an evolutionary path. The results show that a reasonable income distribution coefficient can promote the game behavior of both parties to the direction of active collaborative innovation; The reduction of innovation cost and the improvement of spillover technology absorption capacity can make innovation subjects tend to choose active collaborative innovation strategies. In addition, reputation loss above a specific threshold can effectively inhibit free-riding behavior and encourage innovation subjects to choose active collaborative innovation strategies. The research results provide reference for promoting major projects' technology innovation.

Under the dual erosion conditions of the dry-wet cycle, which is caused by the high chloride salt concentrations in mine water and fluctuations in mine water level, cemented paste backfill (CPB) suffers serious damage and deterioration. To discuss the mechanical properties and permeability characteristics of CPB under erosion, this study designs an immersion experiment for CPB under chloride salt and dry-wet cycle conditions. Through a uniaxial compressive strength (UCS) test, the change law for the mechanical parameters of the CPB was explored, strength constitutive equation of the CPB was constructed, and the process of deterioration of the CPB was analyzed. Through the penetration test, the diffusion characteristics of packing under chloride salt and dry-wet cycle conditions were explored. The results demonstrated that the strength and elastic modulus of the CPB first increased and then decreased rapidly, with maximum decrease rates of 32.2% and 38.2%, respectively. The CPB structure presents an initial non-damage stage, initial damage stage, damage development stage, damage destruction, and residual damage stage. The chloride ion penetration depth gradually increased with an increase in the number of dry-wet cycles, with a maximum diffusion depth of 20.5 mm. The maximum apparent diffusion coefficient of chloride ion was 18.99×10-10m2/s, and the maximum concentration was 0.303 mol/L. Under the double erosion conditions due to chloride salt and dry-wet cycle, the CPB structure is seriously damaged.

In the paper, the authors establish two identities, which can be regarded as nonlinear differential equations, for the generating function of Eulerian polynomials, find two identities for the Stirling numbers of the second kind, and present two identities for Eulerian polynomials and higher order Eulerian polynomials, pose two open problems about summability of two finite sums involving the Stirling numbers of the second kind. Some of these conclusions meaningfully and significantly simplify several known results.

8-Hydroxydeoxyguanosine (8-OHdG) was the most widely used oxidative stress biomarker of the free radical-induced oxidative damage product of DNA, which may allow a premature assessment of various diseases. This paper designed a label-free, portable biosensor device to direct detect 8-OHdG by plasma coupled electrochemistry on transparent and conductive indium tin oxide (ITO) electrode. We reported a flexible printed ITO electrode made from particle-free silver and carbon inks. After inkjet printing, the working electrode was sequentially assembled by gold nanotriangles (AuNTAs) and platinum nanoparticles (PtNPs). This nanomaterial-modified portable biosensor showed excellent electrochemical performance for 8-OHdG detection from 10 μg/mL to 100 μg/mL by our self-developed constant voltage source integrated circuit system. This work demonstrated a portable biosensor for simultaneously integrating nanostructure, electroconductivity, and biocompatibility to construct advanced biosensors for oxidative damage biomarkers. The proposed nanomaterial modified ITO-based electrochemical portable device was a potential biosensor to approach 8-OHdG point-of-care testing (POCT) in various biological fluid samples, such as saliva and urine samples.

In typical Cobalt-chromium (CoCr) alloys powders, aluminum oxide (Al₂O₃) powder can be added. In the present study, we successfully prepared alloyed samples of various powder ratios by laser cladding, and analyzed their microstructure and carbide structural characteristics, including microhardness, biological properties, morphology (using scanning electron microscopy), and crystal structure (using X-ray powder diffraction). Elemental distribution was also determined by energy-dispersive X-ray spectral analysis. The results showed that Al₂O₃ addition caused the alloy to change from slender columnar crystals to columnar grains similar, to equiaxed grains. In addition, Al₂O₃ agglomeration zones appeared, and carbide structures were altered. The mechanism of the observed performance changes was also analyzed.

Sinojackia Hu. comprises five to eight Chinese endemic species with high ornamental and medicinal value. However, the generic limits, interspecific relationships and evolutionary history of the genus remain unresolved. In this study, we newly sequenced and assembled three plastomes of S. oblongicarpa and compared them with those of the other congeneric species to explore the taxonomic delimitation of the species and the evolutionary history of the genus. Plastomes structure of Sinojackia species were extremely conserved in terms of number of genes, sequence length and GC content. Codon usage patterns revealed that natural selection may be the main factor shaping codon usage bias. Our phylogenetic tree shows that Sinojackia is monophyletic and can be divided into two clades. Sinojackia oblongicarpa as a distinct species is supported for it is distantly related to S. sarcocarpa. The evolutionary analysis of morphological features indicates that woody mesocarp is an ancestral feature, while mesocarp undeveloped, spongy and fleshy are the later derived. Sinojackia originated in Central-Southeast China during the early Miocene. In this period, it experienced elevated diversification and migrated from the Central-Southeast China to Hunan Province and Sichuan Province with the development of the Asian monsoon and East Asian flora. Sinojackia experienced elevated diversification at intraspecies levels that mainly occurred in the Quaternary. Glacial-interglacial interactions with the monsoon climate may provide favorable expansion conditions for Sinojackia on a small-scale.

The transportation industry is rapidly transitioning from Internal Combustion Engine (ICE) based vehicles to Electric Vehicles (EVs) to promote clean energy. However, large-scale adoption of EVs can compromise the reliability of the power grids by introducing large uncertainty in the demand. Demand response with a controlled charge scheduling strategy for EVs can mitigate such issues. In this paper, a deep reinforcement learning- based charge scheduling strategy is developed for individual EVs by considering user’s dynamic driving behavior and charging preferences. The temporal dynamics of user’s anxiety about charging the EV battery is rigorously addressed. A dynamic weight allocation technique is applied to continuously tune user’s priority for charging and cost-saving with respect to charging duration. The sequential charging control problem is formulated as a Markov decision process, and an episodic approach to the deep deterministic policy gradient (DDPG) algorithm with target policy smoothing and delayed policy update techniques is applied to develop the optimal charge scheduling strategy. A real-world dataset that captures user’s driving behavior, such as arrival time, departure time, and charging duration, is utilized in this study. The extensive simulation results reveal the effectiveness of the proposed algorithm in minimizing energy cost while satisfying user’s charging requirements.

This paper proposes to combat active eavesdropping by intelligent reflecting surface (IRS) backscatter techniques. To be specific, the source (Alice) sends the confidential information to the intended user (Bob), while the eavesdropper (Willie) transmits jamming signal to interrupt the transmission for more data interception. To enhance the secrecy, an IRS is deployed and connected with Alice through fiber to transform the jamming signal into the confidential signal by employing backscatter techniques. Based on the considered model, an optimization problem is formulated to maximize signal-to-interference-plus-noise ratio (SINR) at Bob under the constraints of the transmit power at Alice, the reflection vector at the IRS and the allowable maximum SINR at Willie. To address the optimization problem, an alternate optimization algorithm is developed. The simulation results verify the achievable secrecy gain of the proposed scheme.

Quantum noise limits the sensitivity of laser interferometric gravitational-wave detectors. Given the state-of-the-art optics, the optical losses define the lower bound of best possible quantum-limited detector sensitivity. In this work, we come up with the configuration which allows to saturate this lower bound by converting the signal recycling cavity to be a broadband signal amplifier using an active optomechanical filter. We will show the difference and advantage of such a broadband signal recycling scheme compared with the previous white-light-cavity scheme using the optomechanical filter in [Phys.Rev.Lett.115.211104 (2015)]. The drawback is that the new scheme is more susceptible to the thermal noise of the mechanical oscillator. To suppress the radiation pressure noise which rises along with the signal amplification, squeezing with input/output filter cavities and heavier test mass are used in this work.

Introduction: This study aims to elucidate the clinical diagnostic value of S100 Calcium Binding Protein beta (S100B) in epilepsy, a topic of ongoing debate among European and Asian epilepsy research centres.Methods and analysis: A structured long-term research plan was developed, comprising three phases. Phase one involves observational studies investigating the correlation between S100B levels in serum or cerebrospinal fluid and epilepsy. Phase two integrates observational and randomised controlled data to establish baseline S100B levels across diverse epilepsy demographics, underpinning the predictive value of S100B for epilepsy. Phase three focuses on randomised controlled trials to evaluate the diagnostic accuracy of S100B as an epilepsy biomarker.Ethics and dissemination: All enrolled patients will provide written consent. The ethics committee of the Second People’s Hospital of Gansu Province, Affiliated Hospital of Northwest Minzu University, China, approved the study (GSSEY2022-KY009-01).Registration: The study is registered with PROSPERO (CRD42023425431).

The cytosolic PNGase (peptide:N-glycanase; Png1 in yeast; NGLY1/Ngly1 in human/mice), also known as peptide-N4-(N-acetyl-beta-glucosaminyl)-asparagine ami-dase, is a well-conserved deglycosylation enzyme (EC 3.5.1.52) which catalyzes the non-lysosomal hydrolysis of an N(4)-(acetyl-β-D-glucosaminyl) asparagine residue into N-acetyl-β-D-glucosaminylamine and a peptide containing an aspartate residue. This enzyme (NGLY1) plays essential roles in clearance of misfolded or unassembled gly-coproteins through a process named ER-associated degradation (ERAD). Accumulating evidence also points out that NGLY1 deficiency can cause an autosomal recessive hu-man genetic disorder associated with abnormal development and congenital disorder of deglycosylation. In addition, the loss of NGLY1 can affect multiple cellular pathways, including but not limited to NFE2L1 pathway, Creb1/Atf1-AQP pathway, BMP path-way, AMPK pathway, and SLC12A2 ion transporter, which might be the underlying reasons for a constellation of clinical phenotypes of NGLY1 deficiency. The current comprehensive review indeed uncovers the detailed NGLY1’s structure and its im-portant roles for participation in ERAD, involvement in CDDG and potential treatment for NGLY1 deficiency.

In recent years, the Chinese government pays more and more attention to agricultural development and ecological protection. While improving the cultivated land green use efficiency(CLGUE) is the key to promote the sustainable development of agriculture. This study aims to study the current situation and influencing factors of agricultural production from the perspective of green utilization efficiency of cultivated land. It takes 39 cities in the upper, middle and lower reaches of the Yangtze River basin in China as an example. The CLGUE values in those 39 cities from 2011 to 2020 were specifically measured, using the Super-SBM model, kernel density estimation and geographic detector method. Their temporal and spatial heterogeneity was described, and the influencing factors were detected at both single and interactive levels. The results showed that: （1）From 2011 to 2020, the green utilization efficiency value of cultivated land in the Yangtze River Basin showed an upward trend on the whole; （2）There is a clear spatial heterogeneity the CLGUE values in the Yangtze River Basin cities, as shown by: downstream region > midstream region > upstream region; (3) Cultivated land resource endowment, socioeconomic development, and agricultural production technology are important factors affecting the variability of CLGUE values. However, there are some differences in the degree and direction of influence of different influencing factors on different sample subgroups.

This study presents an advanced Simulated Shearer Machine Cutting Experiment System enhanced with digital twin technology. Central to this system is a simulated shearer drum, designed based on similarity theory to mirror the operational dynamics of actual mining cutters accurately. The setup incorporates a modified machining center equipped with sophisticated sensors that monitor various parameters such as cutting states, forces, torque, vibration, temperature and sound. These sensors are crucial for precisely simulating the shearer cutting actions. The integration of digital twin technology is pivotal, featuring a real-time data management layer, a dynamic simulation mechanism model layer, and an application service layer that facilitates virtual experiments and algorithm refinement. This multifaceted approach allows for in-depth analysis of simulated coal cutting, utilizing sensor data to comprehensively evaluate the shearer's performance. The study also includes tests on simulated coal samples. The system effectively conducts experiments and captures cutting condition signals via the sensors. Through time-domain analysis of these signals, gathered while cutting materials of varying strengths, it is determined that the cutting force signal characteristics are particularly distinct. By isolating the cutting force signal as a key feature, the system can effectively distinguish between different cutting modes. This capability provides a robust experimental basis for coal-rock identification research, offering significant insights into the nuances of shearer operation.

This mini-review explores the comparative efficacy, safety, and clinical outcomes of high-dose proton pump inhibitor (PPI) intravenous infusion versus oral acid pump inhibitor therapy following endoscopic treatment for bleeding peptic ulcers. Recent evidence suggests that intravenous PPIs can significantly reduce the rebleeding rates within the critical first 72 hours post-intervention, with a noted rebleeding rate of 6% compared to 14% in patients receiving oral Vonoprazan (VPZ) therapy. Additionally, the rapid onset of action associated with intravenous administration leads to faster stabilization of vital signs and a reduced need for subsequent blood transfusions. Safety profiles for both intravenous and oral VPZ were favourable, with minimal adverse effects, the most common being transient headaches.However, the findings from our single-centre study with a moderate sample size prompt consideration of more extensive, multicentre trials to enhance the generalizability of the results. Current limitations include potential biases, short-term focus, missing data issues, and a need for long-term outcome data, necessitating further research. Future studies should also explore the cost-effectiveness of intravenous versus oral VPZ and the impact on patient quality of life and long-term mortality rates.This review underscores the importance of tailored PPI therapy in managing bleeding peptic ulcers post-endoscopy. It suggests a potentially pivotal role for intravenous PPIs in high-risk patient groups, advocating for a shift towards more aggressive and immediate care protocols in specific clinical settings.

Objective: The long-term care insurance (LTCI) system was introduced in 2000 to provide financial support for long-term care services to older adults. What is known on this topic report focuses on a comparative analysis of how the LTCI system has affected older people in Japan. Methods: We obtained data from the literature about the LTCI system, compared and analysed the collected articles, and concluded. Results: The LTCI system has improved access to long-term care services, with more older adults receiving care than before the system’s implementation. This service has improved the quality of life for many elderly individuals who require assistance with daily activities. Furthermore, the LTCI system has alleviated the financial burden of long-term care services since the insurance covers a large portion of the costs. It has made older adults maintain their independence and dignity, as they can afford the necessary care without relying solely on their savings or burdening their families. Conclusions: Japan’s LTCI system has positively impacted older adults by improving access to long-term care services and alleviating financial burdens. However, challenges such as increasing demand and variations in service quality need to be addressed to ensure the system effectively supports older people in Japan.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

The next-generation communication systems demand integration of sensing, communication, and power transfer (PT) capabilities, requiring high spectral efficiency, energy efficiency, and low cost, while also necessitating robustness in high-speed scenarios. Integrated sensing and communication systems (ISACS) exhibit the ability to simultaneously perform communication and sensing tasks using a single RF signal, while simultaneous wireless information and power transfer (SWIPT) systems can handle simultaneous information and energy transmission, and orthogonal time frequency space (OTFS) signals are adept at handling high Doppler scenarios. Combining the advantages of these three technologies, a novel cyclic prefix (CP) OTFS based integrated simultaneous wireless sensing, communication, and power transfer system (ISWSCPTS) framework is proposed in this work. Within the ISWSCPTS, the CP-OTFS matched filter (MF) based target detection and parameters estimation (MF-TDaPE) algorithm is proposed to endow the system with sensing capabilities. To enhance the system’s sensing capability, a waveform design algorithm based on CP-OTFS ambiguity function shaping (AFS) is proposed, which is solved by iteratively method. Furthermore, to maximize the system’s sensing performance under communication and PT Quality of Service (QoS) constraints, a semidefinite relaxation (SDR) beamforming design (SDR-BD) algorithm is proposed, solved using through SDR technique. Simulation results demonstrate that the ISWSCPTS exhibits stronger parameter estimation performance in high-speed scenarios compared to orthogonal frequency division multiplexing (OFDM), waveform designed by CP-OTFS AFS demonstrates superior interference resilience, and beamforming designed by SDR-BD strikes a balance in the overall performance of the ISWSCPTS.

Various tissue resident stem cells are receiving attention from basic scientists and clinicians as they hold certain promise for regenerative medicine. This paper is intended to clarify and facilitate the understanding, development and adoption of regenerative medicine in general and specifically of therapies based on unmodified, autologous adipose-derived regenerative cells (UA-ADRCs). To this end, results of landmark experiments on stem cells and stem cell therapy performed in the labs of the authors are summarized, the most intriguing of which are the following: (i) vascular associated mesenchymal stem cells (MSCs) can be isolated from different organs (adipose tissue, heart, skin, bone marrow and skeletal muscle) and differentiated into ectoderm, mesoderm and endoderm, providing significant support for the hypothesis of the existence of a small, ubiquitously distributed, universal vascular associated stem cell with full pluripotency; (ii) the orientation and differentiation of MSCs are driven by signals of the respective microenvironment; and (iii) these stem cells irrespective of the tissue origin exhibit full pluripotent differentiation potential without any prior genetic modification or the need for culturing. They can be obtained from a small amount of adipose tissue when using the appropriate technology for isolating the cells, and can be harvested from and re-applied to the same patient at the point of care without the need for complicated processing, manipulation, culturing, expensive equipment, or repeat interventions. These findings demonstrate the potential of UA-ADRCs for triggering the development of an entire new generation of medicine for the benefit of patients and of healthcare systems.

In the paper, the authors present unified generalizations for the Bell numbers and polynomials, establish explicit formulas and inversion formulas for these generalizations in terms of the Stirling numbers of the first and second kinds with the help of the Faà di Bruno formula, properties of the Bell polynomials of the second kind, and the inversion theorem connected with the Stirling numbers of the first and second kinds, construct determinantal and product inequalities for these generalizations with aid of properties of the completely monotonic functions, and derive the logarithmic convexity for the sequence of these generalizations.

Colonoscopy, essential for diagnosing and treating colorectal cancer, relies on effective bowel preparation to inspect the colonic mucosa fully. Traditional education methods include printed instructions and verbal explanations, but these may not ensure clear patient understanding. Poor bowel preparation can obscure mucosal visibility, delaying cancer diagnosis and treatment. Using the outpatient’s Android mobile device, the mobile health care model is provided as a nursing guide to assist in bowel preparation for colonoscopy. This single-blinded, randomized trial en-rolled patients for colonoscopy at a Northern Taiwan gastroenterology center. Eligible patients were physically and mentally healthy and could communicate in Chinese. The study tested the ColonClean app during bowel preparation. After the procedure, endoscopists rated the prepara-tion quality using the Aronchick Scale. Data analysis with SPSS software (version 25.0) evaluated if the app significantly improved bowel preparation compared to those who did not use it. Forty patients were recruited for both the control (conventional method) and experimental (conven-tional method plus ColonClean app) groups. In the experimental group, endoscopists assessed bowel preparation quality; all achieved at least "Fair," with 75% receiving "Excellent" or "Good" ratings. The ColonClean App enhanced bowel preparation quality more effectively than tradi-tional nursing guidance.

In this work, we discuss a newly proposed scalar-tensor theory in Minkowski spacetime. The basic frame in Minkowski spacetime is obtained. Consider a charged particle in the electromagnetic field, we make an attempt to connect this theory with conventional quantum theory. Two specific models are chosen to calculate values of the time delay.

Up-conversion nanoparticles (UCNP) under near-infrared (NIR) light irradiation have been well investigated in the field of bio-imaging. However, the low up-conversion luminescence (UCL) intensity limits applications. Plasmatic modulation has been proposed as an effective tool to adjust the luminescence intensity and lifetime. In this study discrete dipole approximation (DDA) was explored concerning guiding the design of UCNP@mSiO2-Au structures with enhanced UCL intensity. The extinction effects of gold shells could be changed by adjusting the distance between the UCNPs and the Au NPs by synthesized tunable mesoporous silica (mSiO2) spacers. Enhanced UCL was obtained under 808 nm irradiation. Theoretical predictions could not be demonstrated to full extend by experimental data, indicating that better models for simulation need to better take into account inhomogeneities in particle morphologies.

In recent experimental studies, we reported the aggravating effects of Asian sand dust (ASD) on male reproductive function in mice. However, the effects of fetal ASD exposure on male reproductive function have not been investigated. The present study investigated the effects of fetal ASD exposure on reproductive function in male offspring. Using pregnant CD-1 mice, ASD was administered intratracheally on days 7 and 14 of gestation, and the reproductive function of male offspring was determined at 5, 10, and 15 weeks after birth. The secondary sex ratio was significantly lower in the fetal ASD-exposed mice than in the controls. Histologic examination showed partial vacuolation of seminiferous tubules in immature mice. Moreover, daily sperm production (DSP) was significantly less in the fetal ASD-exposed mice than in the controls. DSP in the fetal ASD-exposed mice was approximately 10% less than the controls at both 5 and 10 weeks. However, both the histologic changes and the DSP decrease were reversed as the mice matured. These findings suggest that ASD exposure affects both the fetal development and the reproductive function of male offspring. In the future, it will be necessary to clarify the onset mechanisms of ASD-induced male fetus death and male reproductive disorders.

It is strongly desirable to accurately detect the clouds in hyperspectral images onboard before compression. However, conventional onboard cloud detection methods are not appropriate to all situation such as shadowed cloud or darken snow covered surfaces which are not identified properly in the NDSI test. In this paper, we propose a new spectral–spatial classification strategy to enhance the orbiting cloud screen performances obtained on hyperspectral images by integrating threshold exponential spectral angle map (TESAM), adaptive Markov random field (aMRF) and dynamic stochastic resonance (DSR). TESAM is performed to classify the cloud pixels coarsely based on spectral information. Then aMRF is performed to do optimal process by using spatial information, which improved the classification performance significantly. Some misclassification points still exist after aMRF processing because of the noisy data in the onboard environment. DSR is used to eliminate misclassification points in binary labeling image after aMRF. Taking level 0.5 data from hyperion as dataset, the average overall accuracy of the proposed algorithm is 96.28% after test. The method can provide cloud mask for the on-going EO-1 images and related satellites with the same spectral settings without manual intervention. The experiment indicate that the proposed method reveals better performance than the classical onboard cloud detection or current state-of-the-art hyperspectral classification methods.

The purpose of this study is to ascertain whether implementation difficulty can be used in slot allocation model as a new mechanism for slightly weakening grandfather right. According to which, a linear integer programming model is designed to compare and analyze displacement, implementation difficulty and priority with different weights. Test results show that the implementation difficulty can be significantly reduced without causing excessive displacement and disruption of existing priorities, by weight setting while declared capacity is cleared. In addition to this, whether the movements are listed in order of descending priority or not have great impact on displacement and implementation difficulty within slot allocation model. Capacity is surely a key factor affecting displacement and implementation difficulties. This study contributes to propose a new mechanism for slightly weakening grandfather right, which can help decision makers to upgrade slot allocation policies.

Precipitation downscaling is widely employed for enhancing the resolution and accuracy of precipitation products from general circulation models (GCMs). In this study, we propose a novel statistical downscaling method to foster GCMs’ precipitation prediction resolution and accuracy for monsoon region. We develop a deep neural network composed of convolution and Long Short Term Memory (LSTM) recurrent module to estimate precipitation based on well-resolved atmospheric dynamical fields. The proposed model is compared against GCM precipitation product and classical downscaling methods in the Xiangjiang River Basin in South China. Results show considerable improvement compared to the ECMWF-Interim reanalysis precipitation. Also, the model outperforms benchmark downscaling approaches, including 1) quantile mapping, 2) support vector machine, and 3) convolutional neural network. To test the robustness of the model and its applicability in practical forecast, we apply the trained network for precipitation prediction forced by retrospective forecasts from ECMWF model. Compared to ECMWF precipitation forecast, our model makes better use of the resolved dynamical field for more accurate precipitation prediction at lead time from 1 day up to 2 weeks. This superiority decreases along forecast lead time, as GCM’s skill in predicting atmospheric dynamics being diminished by the chaotic effect. At last, we build a distributed hydrological model and force it with different sources of precipitation inputs. Hydrological simulation forced with the neural network precipitation estimation shows significant advantage over simulation forced with the original ERA-Interim precipitation (with NSE value increases from 0.06 to 0.64), and the performance is just slightly worse than the observed precipitation forced simulation (NSE=0.82). This further proves the value of the proposed downscaling method, and suggests its potential for hydrological forecasts.

Turbidity stands as a crucial indicator for assessing water quality, and while turbidity sensors exist their high cost prohibit their extensive use. In this paper, we introduce an innovative turbidity sensor, and it is the first low-cost turbidity sensor which is designed specifically for long-term stormwater in-field monitoring. Its low cost ($23.50 USD), enables the implementation of high spatial resolution monitoring schemes. The sensor design is available under open hardware and open-source licences, and the 3D-printed sensor housing is free to modify based on different monitoring purposes and ambient conditions. The sensor was tested both in the laboratory and in the field. The laboratory results show a strong linear relationship (R2 > 0.99) between the sensor readings and the commercial hand-held turbidimeter (Thermo Scientific AQ4500) results of the solution. In the field, the low-cost sensor measurements were statistically significantly correlated (p < 0.01) to a standard high-cost commercial turbidity sensor (GreenSpan TS-1000). Biofouling and drifting issues were also analysed after the sensors were deployed in the field for more than 6 months, showing both biofouling and drift occur during monitoring. Nonetheless, in terms of maintenance requirements, the low-cost sensor exhibited similar needs compared to the Green-Span sensor.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

Geological structures such as joints and faults in rock mass have significant influence on open pit mining. Hence, it is critical to develop a understanding of dynamic joint behaviour under blasting loading. This in turn can provide both theoretical and practical guidance to improve blasting rock fragmentation and associated bucket excavating efficiency. In this paper, delayed blasting on the highwall bench at Baiyunebo open-pit mine was used as an example, a nonlinear joint blasting model was also constructed. By simplifying the blasting wave propagation velocity, the P-wave normal incidence to the joint was obtained. The peak vibration velocity was 0.33m/s at 3.0s. The S-wave reflected by the joint interface was first reflected backward and then forward, which the peak vibration velocity was 0.027 m/s. By combining the relevant stress and displacement theories of type I and II cracks, the equipotential diagrams of the stress and displacement field with the vibration velocity of the particle were obtained. σx was positive in the direction of 0~330° and subjected to tensile stress, whereas σy was positive in the direction of 0~180° and under tensile stress. The longitudinal σy along joint was low in compressive stress distribution area and did not affect surrounding rock at the time. The stress concentration appeared in the lower right corner. Based on the continuous behavior of stress wave in joints, the asymmetry and continuous changes reflected in the whole process could not be analysed by the contour diagram. Hence, ANSYS used to analyse distribution of the stress field. The intensity of the shock wave after detonation was greater than that of the rock strength. Subsequently, the sub-layer shock wave supplemented the shock wave energy that was not enough to break the rock and induced further cracking. This was able to be visualized by the degree of color change post-processing. It was concluded that with the attenuation of the detonation wave energy, the stress exhibited a decreasing trend in this process. According to distribution of the peak effective stress, it was found that the peak value first increased to 10-12 MPa and then showed a downward trend. Overall, the results were validated against the finite element simulation and mathematical analysis.

Correlation between the category richness (CR) and morphological diversity (MD) of some communities at a local scale was found pendent, however, examination of a whole category using a large dataset are lacking. In this study, 1119 jewel species from around the world representing all existing subfamilies and 33.78% of Buprestidae genera were selected as a test group. A geometric morphometric analysis on the contour of homologous traits: pronotum and elytra was conducted to quantify morphological diversity. Correlations between MD and CR among subfamilies were found to be consistently positive with the exceptions of a pronotum genus-level test on the subfamily category. The correlation was also found to be higher at the genus-level than it on the species-level, in both pronotum and elytron measurements. Based on our analyses the hypothesis of positive correlations was expected in the genus-level test of jewel beetles but rejected in species-level test. The inconsistent correlation between morphological diversity and species richness revealed convergent morphological variation of pronotum under the similar functional diversity in Buprestidae. In addition, our test revealed variable correlation between MD and CR based on different groups and characters, which might be caused by morphological changes under coevolution with different ecological factors.

Leaf variegation pale yellowing is observed in the Calcineurin B-Like-Interacting Protein Kinase14 (CIPK14) overexpression line (oeCIPK14) and double knockout WHIRLY1/WHIRLY3 (why1/3) lines of Arabidopsis, the distribution of WHIRLY1 (WHY1) protein between plastids and the nucleus are affected by the phosphorylation of WHY1 by CIPK14. To elucidate the coregulation of CIPK14 and WHIRLY1/WHIRLY3 mediated leaf pale yellowing, a differential proteomic analysis is conducted between the oeCIPK14 variegated (oeCIPK14-var) line, why1/3 variegated (why1/3-var) line and wild type (WT). More than 800 protein spots are distinguished on each gel, 67 differential abundance proteins (DAPs) are identified by matrix-assisted laser desorption ionization-time of flight/time of flight mass spectrometry (MALDI-TOF/TOF-MS), of which, 34 DAPs are in the oeCIPK14-var, 33 DAPs are in the why1/3-var compared to WT. Five overlapping proteins differentially change both in the oeCIPK14-var and in the why1/3-var. They are ATP-dependent Clp protease proteolytic subunit-related protein 3 (ClpR3), Ribulose bisphosphate carboxylase large chain (RBL), Beta-amylase 3 (BAM3), Ribosome-recycling factor (RRF), Ribulose bisphosphate carboxylase small chain (RBS). Bioinformatics analysis show that most of DAPs are involved in photosynthesis, defense and antioxidation pathway, protein metabolism, amino acid metabolism, energy metabolism, malate biosynthesis, lipid metabolism and transcription. Thus, the photosystem parameters are measured that the content of chlorophyll, the photochemical efficiency of PSⅡ (Fv/Fm), and electron transport rates (ETR) decrease in the why1/3-var and oeCIPK14-var, but the non-photochemical quenching (NPQ) increases. Both mutants show high sensitivity to strong light. Based on the annotation of DAPs from both why1/3-var and oeCIPK14-var lines, we conclude that CIPK14 phosphorylation mediated WHY1 deficiency in plastids is related to impairment of protein metabolism leading to chloroplast dysfunction.

Cu-Sn shape-memory microwires were fabricated by a glass-coated melt spinning method. Effects of Sn content on the microstructure and mechanical property of microwires were investigated. The phase transforms from martensite to austenite with Sn content increasing from 14.0 atomic percent (at.%) to 16.5 at.%, and highly ordered intermetallic phase, δ, formed with higher Sn content. The fracture stress, σf, and the critical stress for martensitic transformation, σMs, increases with Sn content increasing. The mechanical property as well as superelasticity were improved greatly by high cooling rate of the glass-coated melt spinning method.

As development progresses, when the bottom hole flowing pressure or formation pressure is less than the saturation pressure of crude oil in the reservoir, oil and gas two-phase seepage occurs in the reservoir. Due to the characteristics of oil and gas two-phase seepage, after the oil and gas two-phase seepage occurs in the reservoir, the well production will be reduced, or even greatly reduced. Therefore, how to predict the horizontal well capacity better in this case is an important problem that needs to be solved urgently. In this paper, the method and process of establishing the transient calculation model of two-phase flow in horizontal wells are introduced in detail from three aspects: fluid physical properties, reservoir oil-gas two-phase seepage, and the coupling model of Inflow Performance and Flow in Wellbore. The model is more reliable through the verification of production data from five wells in two oilfields.

Harsh parenting could be regarded as a harsh form of behavior, feelings and attitude towards children in the process of parenting. According to the theory of intergenerational transmission of violence, harsh parenting is an important factor affecting children's aggressive behavior, but the theory does not clarify the specific action path between the harsh parenting and aggressive behavior. In order to reveal the relationship between harsh parenting and aggressive behavior of juvenile delinquents, 604 male juvenile delinquents (N=604, Mage=16.57 years, SD=0.612 years) were investigated using Harsh Parenting Questionnaire, Buss-Perry Aggression Questionnaire, Multidimensional Peer-Victimization Scale, and the Word Sentence Association Paradigm for Hostility in Chinese version. Analysis using structural equation modeling procedures showed that (a) all variables were positively associated with each others; (b) the partial indirect effect of harsh parenting on aggressive behaviors was realized through the mediator of peer victimization and hostile attribution bias independently, (c) as well as the partial indirect effect through the mediator of peer victimization and hostile attribution bias sequentially. The results suggested that harsh parenting can explain the high aggressive behavior of male juvenile delinquents. Moreover, harsh parenting may also lead to the formation of hostile attribution bias by increasing the risk of peer victimization, and ultimately lead to the formation of highly aggressive behaviors.

Aims: The study aims to take the COVID-19 pandemic as an example to provide a scientific reference for diabetic patients’ self-health management and nurses’ work for these patients when facing future pandemics. Review Methods: It conducted a comprehensive literature search and analysed relevant texts. This article reviews the daily health management of diabetic patients in the context of the COVID-19 pandemic and the role that nurses should play in this process. Results: Diabetic patients face challenges in self-health management during the pandemic, including disruptions in healthcare access, increased mental problems, and unhealthy lifestyles. Nurses serve as the front-line interface between these patients and the healthcare system. Adopting telehealth and remote consultation has effectively bridged the gap created by social distancing measures. Conclusion: Daily self-health management can significantly improve glycemic control and reduce the risk of diabetes-related complications, which is vital during the pandemic when patients may be experiencing disruptions to their routine care. Moreover, empowering patients through educational initiatives led by nurses can bring better self-monitoring, medication adherence, and lifestyle modifications, all of which are crucial in mitigating the effects of diabetes on the body’s immune response, thus reducing the severity of COVID-19 if contracted.

This review article delves into the multifaceted nature of primary ovarian insufficiency (POI), a condition marked by diminished ovarian function before age 40, underscoring the complexity of its aetiology encompassing genetic, autoimmune, infectious, and environmental factors. A significant focus is placed on the potential role of single-gene mutations, such as those in FMR1, BMP15, and GDF9, in the pathogenesis of POI, highlighting the intricate interplay between genetics and ovarian health. The article also explores innovative therapeutic avenues, including the activation of dormant follicles in vitro, offering hope for fertility restoration in affected individuals. Despite the prevalence of traditional treatments, such as Chinese medicine and hormone therapy, in China, these approaches often need to meet therapeutic needs, underscoring the urgency for advanced research and tailored treatment strategies. The discovery of a pituitary tumour-associated POI case further complicates the diagnostic landscape, suggesting a broader diagnostic lens and more in-depth research to unravel the complex underpinnings of POI and enhance patient care.

This paper uses probability method to evaluate the fire safety performance of prestressed steel-concrete beam bridges based on simulation experimental research. Firstly, fire simulation experimental sample analysis was conducted on actual small box girder bridges to obtain the structural response of prestressed steel-concrete structures under fire, which is in line with engineering practice. Next, construct a reliability analysis model for the fire resistance performance of prestressed steel-concrete beam bridges; Combining reliability theory with finite element method, establish a reliability analysis method for the fire resistance performance of prestressed steel-concrete beam bridges. Subsequently, a safety factor evaluation model for the fire resistance performance of prestressed steel-concrete beam bridges was proposed, and a safety factor evaluation method for the fire resistance performance of prestressed steel-concrete beam bridges based on reliability back analysis was established. Finally, based on the analysis of the structural response after a fire in a specific case of a simply supported to continuous prestressed steel-concrete continuous beam bridge project, a structural resistance sample of the prestressed steel-concrete beam bridge is generated through uniform design method, and statistical analysis is conducted. Subsequently, probability methods are used to evaluate the safety of the prestressed steel-concrete beam bridge after a fire. Through analysis, it can be concluded that the time of fire has a significant impact on the structural performance of prestressed steel-concrete beam bridges, and the randomness of parameters has a significant impact on the safety reserve of prestressed steel-concrete beam bridges after fire. It is necessary to pay attention to it in specific engineering practice and strengthen the monitoring and statistics of structural random characteristics.

The current regeneration mode of public space in the old city of Guangzhou is ineffective, thus necessitating supplementation with a more systematic methodology. The “plug-in design” targets sustainable regeneration while preserving the overall urban texture and context, i.e., has little impact on the spatial qualities of the old city. The ultimate goal is to activate the public space of the old city of Guangzhou point-to-area through the insertion of various plug-ins. In this study, the methodology is applied to Xudi Gaodi Street, the core area of the old city of Guangzhou, to explore its effects on sustainability. The internal public space is isolated and supplied with rigid and flexible plug-ins from multiple dimensions, which not only improves the spatial environment but also injects new urban formats. This work provides a specific solution for regeneration in Guangzhou’s old city while enhancing empirical knowledge of the plug-in design to support urban regeneration theory and further practical development.

As the largest energy consumer and carbon emitter, China has made substantial efforts to improve energy efficiency for decrease energy consumption, while the energy rebound effect determines its effectiveness. The embodied energy consumption of construction projects accounted for nearly one-sixth of the total economy's energy consumption in China. This paper is based on the logical relationship among capital input, technological progress, economic growth, and energy consumption, adapting an alternative estimation model to estimate the energy rebound effect for the construction industry in China for the first time. Empirical results in our paper reveal that the energy rebound effect for the construction industry in China is about 59.5% for the period of 1990–2014. The results indicate that the energy rebound effect does exist in China’s construction industry and it presented a fluctuating declining trend. This implies that half of the energy savings by technological progress is achieved. In addition, China’s government should implement proper energy pricing reforms and energy taxes to promote the sustainable development of China’s construction industry.

Nickel base superalloy GH4169 is a material with strong mechanical properties and is difficult to process. In order to reduce tool wear during material processing and improve workpiece surface processing quality, based on the finite element simulation software DEFORM, the influence of n, ap, and fz parameters on tool wear during carbide tool milling GH4169 was studied, and a simulation orthogonal experimental model was established, The prediction model of tool wear is obtained; The ultrasonic vibration milling is compared with ordinary milling, and the improvement degree of different coating materials on carbide tool wear is explored. The results show that the ultrasonic vibration signal is helpful to reduce tool wear, improve the surface quality of the workpiece, and improve the stability of the milling process. TIALN/TIN (WC) composite coated tools have good cutting performance, help to reduce tool temperature, reduce tool wear, and improve tool life.

In the paper, the authors view some ordinary differential equations and their solutions from the angle of (the generalized) derivative polynomials and simplify some known identities for the Bernoulli numbers and polynomials, the Frobenius-Euler polynomials, the Euler numbers and polynomials, in terms of the Stirling numbers of the first and second kinds.

Construction using earth materials demonstrates ecological sustainability using locally sourced natural materials and environmentally friendly demolition methods. In this study, the environmental impact of adding cement to soil materials for rammed-earth farmhouse construction in rural China was investigated and comparatively simulated using the One Click LCA database, focusing on the conflict between sustainability objectives and the practical aspects of cement addition. By analyzing how the addition of cement aligns with local construction practices and by addressing the debate surrounding the inclusion of cement in rammed earth construction, our objective is to provide insights into achieving a balance between the environmental impact and the pragmatic considerations of using cement in earthen building practices. Three local structure scenarios are evaluated via simulations: a cement-stabilized rammed earth wall, a fired brick wall, and a localized reinforced concrete frame structure. The quantitative environmental impacts are assessed, and the qualitative differences in adaptation, economic sustainability, and other factors are examined in the context of present-day development in rural China. The results show that the use of cement-stabilized rammed earth wall-supported structures is associated with higher embodied carbon emissions compared to structures supported by reinforced concrete frames and enclosed by brick walls; however, these emissions are lower than those for brick wall-supported structures, while effectively meeting the structural requirements. In addition, the use of cement-stabilized earth for perimeter walls simplifies material management and disposal throughout the building's life cycle, and the cost-effectiveness of cement has been found to be substantially greater than that of reinforced concrete frames and brick structures, improving economic viability and social acceptability, especially among low-income communities in rural areas.

This study numerically evaluated the long-term and stable trends of meandering channel planform at different mean annual subcritical flows based on a depth-averaged linearized meander evolution model. The calculation cases included an idealized sine-generated meander with moderate max-deflection angle and a typical natural meander - Jiyun River (in China). Within the increase of the selection of the mean annual width-depth ratio in a certain scope, the results showed some specific phase characteristics of channel centerline evolution: (1) the meander straightening trend became weaker in phase 1 (B/H ≤ 16.5) and gradually turned into the meander developing trend in phase 2 (B/H ≤ 27) with the overall immunity to flow magnitude; (2) the symmetric development form along the transverse direction perpendicular to the flow average direction was broken starting from the downstream tail in phase 3 (B/H ≤ 28.9), meantime accompanied by the highlight of flow effects when the mean annual B/H exceeded 28; (3) in phase 4 (B/H ≤ 29.5), there occurred obvious incipience and jump process of the channel sensitivity responding to flow when the selected B/H crossed 29.3, which were very similar to the transition process from the laminar flow to turbulent flow. Besides, the initial sinuosity and curvature-ratio indicator could contribute much to the channel evolutionary state, as demonstrated in the comparison between natural Jiyun River case and the correspondingly idealized sine-generated meander case with the same level of mean annual B/H. This research provides innovation spaces for deeper meander mechanism exploration and effective riparian management.

We conducted the meander evolution experiments incorporating the effects of riparian vegetation and the series of upper vortex flow disturbances induced by a scour pit simultaneously. Two employed nonlegume plants with salinity and alkalinity resistance, had uniform degrees of seedling normal growth and different lengths of root networks. Our results show that riparian vegetation in general can consolidate the single-thread channel planform without branching outward under the flooding flow conditions. Transverse point bars on inner banks were instead by downstream scroll bars in overall channel for long, unless the coupling of riparian vegetation and flood scour. Shallow-rooted plant was inadequate to resist the inner-bank cutting effect brought by the upper vortex flow. Deep-rooted plant can stabilize the bank-lines and thalweg significantly, but that was susceptible to locally low vegetation coverage. Using evolutionary spectral analysis based on thalweg, we found streamwise high-frequency distribution of bed topography mainly concentrated downstream the bifurcation interface in unvegetated scenario when faced with a flood, shrank to the upper isolated turning interface in shallow-rooted scenario, and conversely stood out along the bare roots disturbed region in deep-rooted scenario. This experimental study expands a much wider understanding of vegetation effects in hydro-bio-geomorphological systems engineering.

Visual-inertial integrated navigation system (VINS) has been extensively studied over the past decades to provide accurate and low-cost positioning solutions for autonomous systems. Satisfactory performance can be obtained in an ideal scenario with sufficient and static environment features. However, there are usually numerous dynamic objects in deep urban areas, and these moving objects can severely distort the feature tracking process which is fatal to the feature-based VINS. The well-known method mitigates the effects of dynamic objects is to detect the vehicles using deep neural networks and remove the features belongs to the surrounding vehicle. However, excessive exclusion of features can severely distort the geometry of feature distribution, leading to limited visual measurements. Instead of directly eliminating the features from dynamic objects, this paper proposes to adopt the visual measurement model based on the quality of feature tracking to improve the performance of VINS. Firstly, a self-tuning covariance estimation approach is proposed to model the uncertainty of each feature measurements by integrating two parts: 1) the geometry of feature distribution (GFD), 2) the quality of feature tracking. Secondly, an adaptive M-estimator is proposed to correct the measurement residual model to further mitigate the impacts of outlier measurements, such as the dynamic features. Different from the conventional M-estimator, the proposed method effectively alleviates the reliance of excessive parameterization of M-estimator. Experiments are conducted in a typical urban area of Hong Kong with numerous dynamic objects, and the results show that the proposed method could effectively mitigate the effects of dynamic objects and improved accuracy of VINS is obtained when compared with the conventional method.

The development of biosensors with high sensitivity and low-detection limits provides a new direction for medical and personal care. Graphene and graphene derivatives have been used to prepare various types of biosensors due to their excellent sensing performance (e.g. high specific surface area, extraordinary electronic properties, electron transport capabilities and ultrahigh flexibility). This perspective review focuses on graphene-based biosensors for quantitative detection of cancer related biomarkers such as DNA, miRNA, small molecules and proteins by integrating with different signal outputting approaches including fluorescent, electrochemistry, surface plasmon resonance, surface enhanced Raman scattering etc. The article also discussed their challenges and potential solutions along with future prospects.

This study presents a comprehensive investigation of entropy generation during natural convection in a porous medium with Casson fluid. The governing equations, including the momentum, energy, and entropy balance equations, are solved numerically using finite element method. Through the analysis, various parameters affecting entropy generation are investigated, such as the Casson fluid parameter, Radiation, Prandtl number, and Rayleigh number. The results indicate that the Casson fluid parameter significantly influences the flow and heat transfer characteristics, while the Darcy number and Rayleigh number control the intensity of natural convection. Moreover, the Prandtl number determines the relative significance of heat transfer compared to viscous effects.

Solid porous materials, like zeolites, have been widely used in a variety of fields such as size and shape-selective absorption/separation and catalysis because of their porosity. But there are few liquid materials exhibit permanent porosity. Porous liquids are a novel material that combine the properties of fluidity and permanent porosity. It has potential applications in many fields such as gas separation, storage and transport. Herein, we report a novel Type 1 porous liquid prepared based on Silicalite-1. The pore size of this porous liquid was determined by positron annihilation lifetime spectroscopy (PALS), and the CO2 capacities was determined by the intelligent gravimetric analyser (IGA). The unique properties of this porous liquid can promote its application in many fields such as gas storage and transport.

In the paper, using two inversion theorems for the Stirling numbers and binomial coecients, employing properties of the Bell polynomials of the second kind, and utilizing a higher order derivative formula for the ratio of two dierentiable functions, the authors present two explicit formulas, a determinantal expression, and a recursive relation for a sequence of unnamed polynomials, derive two identities connecting the sequence of unnamed polynomials with the Bell polynomials, and recover a known identity connecting the sequence of unnamed polynomials with the Bell polynomials.

In the paper, by virtue of the Faà di Bruno formula, some properties of the Bell polynomials of the second kind, and an inversion formula for the Stirling numbers of the first and second kinds, the authors establish meaningfully and significantly two identities which simplify coefficients in a family of ordinary differential equations associated with higher order Bernoulli numbers of the second kind.

In the paper, by virtue of the Fa`a di Bruno formula, some properties of the Bell polynomials of the second kind, and the inversion formulas of binomial numbers and the Stirling numbers of the first and second kinds, the authors simplify meaningfully and significantly coefficients in two families of ordinary differential equations associated with higher order Frobenius–Euler numbers.

With the rise of the Internet of Things (IoT), maintaining data confidentiality and protecting user privacy have become increasingly challenging. End devices in IoT are often deployed in unattended environments and connected to open networks, which can make them vulnerable to physical tampering and other security attacks. Different authentication key agreement (AKA) schemes have been validated to date, but most schemes do not cover the necessary security features or are incompatible with resource-constrained end devices. Besides, their security proofs have been performed under the real-or-random model, which is not guaranteed to be secure in real applications. To reduce the weaknesses, we present an AKA protocol for end devices and servers. The proposal leverages the ECC-based key exchange mechanism and one-way hash function-based message authentication method to achieve mutual authentication, user anonymity, and forward security. Formal security proof of the proposed scheme is performed under the standard model with the elliptic curve encryption computational assumptions, and an automatic formal verification was performed with ProVerif. Further, the performance comparison verifies that our scheme reduces computation and communication costs while providing improved security features.

The study of the area model of Pinus tabulaeformis forest provides an important reference for improving the management of Pinus tabulaeformis and revealing the growth law of Pinus tabulaeformis. According to the classification method proposed by Munro, stand growth and harvest prediction models are divided into three categories: full stand model, single wood model and diameter distribution model. Based on the fixed sample data of Shangluo Pinus tabulaeformis, the spatial instead of time method is used to process the data, and the weight coefficient of each model in the combined prediction model is calculated by using the optimal weighting method. The single wood model, the whole forest model and the diameter distribution model are combined by the combined prediction method to integrate the fault area prediction of Pinus tabulaeformis forest. The results show that the combined prediction method is more accurate than the single model (single wood model, whole forest model and diameter distribution model). At the same time, the method can improve the compatibility of the forest break area prediction model, ensure the consistency of the forest break area prediction, and provide a new direction for the research of forest resource monitoring and investigation.

This paper presents a novel approach for semantic segmentation of building roof in dense urban environment with Deep Convolution Neural Network (DCNN) using imagery acquired by a Chinese Very High Resolution (VHR) satellite mission, i.e. GaoFen-2 (GF-2). To provide an operational end-to-end work flow for accurate build roof mapping with feature extraction as well as image segmentation, a fully convolutional DCNN with both convolutional and deconvolutional layers is designed to perform the VHR image analysis for labeling pixels. Since the diverse urban patterns and building styles in large areas, sample image data sets of building roof and non-building roof are collected over different metropolitan regions in China. We selected typical cities with dense urban environment in each metropolitan region as study areas for collecting training and test samples. High performance cluster with GPU-mounted workstations is employed to perform the model training and optimization. With the building roof samples collected over different cities, the predictive model with multiple NN layers is developed for building roof labeling. The validation of the building roof map shows that the overall accuracy(OA) and the mean Intersection Over Union( mIOU) of DCNN based segmentation are 94.67%, 0.85 respectively, while CRF-refined segmentation achieved OA of 94.69% and mIOU of 0.83. The results suggest that the proposed approach is a promising solution for building roof mapping with VHR images over large areas across different urban and building patterns. With the operational acquisition of GF2 VHR imagery, it is expected to develop an automated pipeline for operational built-up area monitoring and timely update of building roof map over large areas.

Aiming to improve the flame retardancy performance of natural rubber (NR), we developed a novel flame retardant synergistic agent through grafting of MCM-41 to graphene oxide (GO)，named as GO-NH-MCM-41，as an assistant of intumescent flame retardants (IFR). The structure of GO-NH-MCM-41 was characterized by FTIR, TEM and SEM tests, which confirmed that a fine grafting had been applied between GO and MCM-41. The flame retardancy of NR/IFR/GO-NH-MCM-41 composites was evaluated by limited oxygen index (LOI), UL-94 and cone calorimeter test. The LOI value of NR/IFR/GO-NH-MCM-41 reached to 26.3%; the UL-94 ratings improved to V-0 rating. Moreover, the addition of GO-NH-MCM-41 obviously decreased the peak heat release rate (PHRR) and the total heat release (THR) of the natural rubber composites. And the addition of GO-NH-MCM-41 increased the thickness of char residue. The images of SEM indicated the char residue were more compact and continuous. The degradation of GO-NH-MCM-41 based NR composites completed with a mass loss of 35.57% at 600 ℃. The tensile strength and the elongation at break of NR/IFR/GO-NH-MCM-41 composites were 13.9 MPa and 496.7%, respectively. The results of rubber process analyzer (RPA) reached the maximum value, probably due to a better network of the fillers in the matrix.

In the note, the authors find several simple and explicit forms for a family of inhomogeneous linear ordinary differential equations studied in "D. Lim, Differential equations for Daehee polynomials and their applications, J. Nonlinear Sci. Appl. 10 (2017), no. 4, 1303-1315; Available online at http://dx.doi.org/10.22436/jnsa.010.04.02".

In the paper, the authors nd a new closed expression for the Fibonacci polynomials and, consequently, for the Fibonacci numbers, in terms of a tridiagonal determinant.

In the paper, by virtue of techniques in combinatorial analysis, the authors simplify two families of nonlinear ordinary differential equations in terms of the Stirling numbers of the first kind.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

Background The spread of COVID-19 continues, the mutation of SARS-COV-2 is still difficult to control, and the need for antiviral drugs to treat COVID-19 remains urgent. The use of arbidol in the treatment of COVID-19 is limited and controversial. Methods To clarify the efficacy of arbidol on COVID-19, we collected 25 cases and 178 related studies. We analyzed the treatment information of arbidol based on the obtained cases, expanded the scope of the study, and collected current studies on the treatment of COVID-19 in various databases for in-depth analysis. Results History analysis showed that arbidol was effective (76% cure rate) compared with other drugs. However, compared with other antiviral drugs or standard therapy, the arbidol group had no significant advantage in reducing the time to negative virus transformation, length of hospital stays, or improvement in CT (MD=0.22, 95%CI -0.29-0.73; MD = 0.61, 95% CI 1.46 to 2.67; RR=1.15, 95%CI 0.88-1.50); Analysis of adverse events showed no significant difference between the arbidol group and the other groups (RR=0.82, 95%CI 0.25-2.71). Conclusion Our study showed that arbidol had no significant effect on COVID-19, but showed a slight advantage in CT improvement and adverse events. Our study objectively evaluated the efficacy of arbidol in the treatment of COVID-19 and provided some guidance for arbidol in the treatment of COVID-19.

In this work, we try to find a way to describe the physical law of micro-world under the frame of a space-time theory. By introducing the scalar fields $\mathcal{D}\left( x\right)$ and $\zeta\left( x\right) $, we rewrite the action of conventional field theory and the Lagrangian describing the motion of the particle, where a modified space-time relation is obtained. To test the correctness of this attempt, we demonstrate the Klein-Gordon equation by the Hamilton-Jacobi method in four dimensional form and present a time delay for the ground state of hydrogen atom.

The farnesoid X receptor (FXR)/βKlotho/fibroblast growth factors (FGFs) pathway is crucial for maintaining the intestinal barrier and preventing colorectal cancer (CRC). We used an FXR ago-nist, GW4064, and FXR knockout (KO) mice to investigate the role of FXR/Klothos/FGFs pathways in lipopolysaccharide (LPS)-induced intestinal barrier dysfunction and colon carcinogenesis. The results showed that upregulation of FXR in enterocytes effectively ameliorated intestinal tight junction markers (claudin1, Zonula occludens-1), inflammation, and bile acid levels, thereby protecting mice from intestinal barrier dysfunction and colon carcinogenesis. GW4064 treatment increased FXR, αKlotho, βKlotho, FGF19, FGF21, and FGF23 in wild-type mice exposed to LPS, while FXR KO mice had decreased levels. FXR KO mice exhibited elevated colon cancer markers (β-catenin, LGR5, CD44, CD34, Cyclin D1) under LPS, underscoring the pivotal role of FXR in inhibiting the development of colon tumorigenesis. The varying gut microbiota responses in FXR KO mice versus wild-type mice post-LPS exposure emphasize the pivotal role of FXR in pre-serving intestinal microbial health, involving Bacteroides thetaiotaomicron, Bacteroides acidifaciens, and Helicobacter hepaticus. Our study validates the effectiveness of GW4064 in alleviating LPS-induced disruptions to the intestinal barrier and colon carcinogenesis, emphasizing the importance of the FXR/αKlotho/βKlotho/FGFs pathway and the interplay between bile acids and gut microbiota.

Classic Hodgkin lymphoma (cHL) is a lymphoid neoplasm composed of rare neoplastic Hodgkin and Reed-Sternberg (HRS) cells surrounded by a reactive tumor microenvironment (TME) with suppressive properties against anti-tumor immunity. TME is mainly composed of T-cells (CD4 helper, CD8 cytotoxic and regulatory), and tumor-associated macrophages (TAMs) but the impact of these cells on the natural course of the disease is not absolutely understood. TME contributes to the immune evasion of neoplastic HRS cells through production of various cytokines and/or aberrant expression of immune checkpoint molecules, in ways that have not been fully understood yet. Herein, we present a comprehensive review of findings regarding the cellular components and the molecular features of the immune TME in cHL, its correlation with treatment response and prognosis as well as the potential targeting of the TME with novel therapies. Among all cells, macrophages appear to be a most appealing target for immunomodulatory therapies, based on their functional plasticity and antitumor potency.

With the growing of university chemistry experiment projects, scientific research personnel, specialized equipment, laboratory accident is increasing yearly. And accident data lacks a safety platform to store related information and cannot be guaranteed for efficient conditional sharing. To solve these problems, we designed a laboratory accident system to store, share related data and predict risk level. In this paper, we manually collected chemistry laboratory accidents by python software and class assignments, then analyses risk factor variables using Spsspro, finally established a prediction model using Stata. We intended to register laboratory related data into proposed chemistry accident system based on data ownership safety architecture. The chemistry accident system can break data barriers using confirmation and authorization key technology to trace non-tampered data source in real time when emergency accident happens. Meanwhile, our proposed system can use our designed accident risk model to predict risk level of any experiment project. It can also recommend appropriate safety education models.

The thermoelectric generator (TEG) stands out in many energy harvesters due to its simple structure, small size, etc. However, previous studies rarely probe into the influence of TEG internal resistances on extracting maximum power from TEG, and tracking efficiency is limited. By analyzing the relationship between the tracking efficiency and the TEG internal resistances, a time exponential rate perturbation and observation (P&amp;O) technology is proposed to achieve maximum power point tracking (MPPT) for a wide resistance range of TEG. Using the time exponential rate P&amp;O, the MPPT circuit observes the power change by comparing PMOS on-time and perturbs the power by adjusting NMOS on-time exponentially. The MPPT circuit is implemented in a 110nm CMOS process. The tracking efficiency keeps a high level from 98.9 to 99.5%. The applicable range of the TEG resistance is from 1 to 12Ω, which is enhanced at least 2.2 times.

Primary urethral malignancies are rare in clinical practice and elderly female are prone to suffer. The cause of PUC is unknown and may be related to long-term chronic inflammation, infection, sexual intercourse, pregnancy and irritation of the urethra. Incipient symptom of PUC is not distinctness and can easily lead to misdiagnosis. The final diagnosis relied on transvaginal ultrasound-guided mass biopsy and urethral biopsy. Early tumor treatment is mainly based on surgical resection. For advanced tumors, it is recommended to adopt a comprehensive treatment plan combining surgery, radiotherapy and chemotherapy We report this case with the aim of bringing attention to that primary urethral cancer progresses rapidly and has a poor prognosis, it is urged to call for a need of diagnostic and treatment specification.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

Whether and how P2X7 receptor knockout (KO) modulates central post-stroke pain (CPSP) induced by lesions of the ventrobasal complex (VBC) of the thalamus regarding behavioral, molecular, and electrical recording parameters remains unclear. Following the experimental protocols of a rat hemorrhage CPSP model, the VBC of the thalamus of wild-type and P2X7 receptor KO mice was injected with 10 mU/0.2 μl type IV collagenase to produce an animal model of stroke-like thalamic hemorrhage. Behavioral data showed that the CPSP group induced thermal and mechanical pain, while the P2X7 receptor KO group showed reduced thermal and mechanical pain behaviors. Molecular assessments revealed that the CPSP group had lower expression of NeuN and KCC2 and higher expression of GFAP, IBA1, and BDNF. The P2X7 KO group showed lower expression of GFAP, IBA1, and BDNF and higher expression of KCC2 than the CPSP group. The expression of NKCC1, GABAa receptor, and TrkB did not differ significantly between the control, CPSP, and P2X7 receptor KO groups. Muscimol application increased multiunit numbers and [Cl-] influx in the membrane in the CPSP group, while P2X7 receptor KO reduced multiunit activity and [Cl-] outflux. P2X4 receptor expression was significantly decreased in the 100 kb but not the 50 kb site in the P2X7 receptor KO group. Altogether, the P2X7 hypothesis of CPSP was proposed, wherein P2X7 receptor KO changed the CPSP pain behavior, numbers of astrocytes and microglia, CSD amplitude of the anterior cingulate cortex and the medial dorsal thalamus, BDNF and KCC2 expression, [Cl-], and P2X4 activation in 100 kb with P2X7 receptors. The present findings have implications for the clinical treatment of CPSP symptoms.

The paper presents an innovative hexapod walking robot built with 3-UPU parallel mechanism. In the robot, the parallel mechanism is used as both an actuator to generate walking and also a connecting body to connect two groups of three legs, thus enables the robot to walk with simple gait by very few motors. In the paper, the forward and inverse kinematics solutions are obtained. The workspace of the parallel mechanism is analyzed using limit boundary search method. The walking stability of the robot is analyzed, which yields the robot’s maximum step length. The gait planning of the hexapod walking robot is studied for walking on both flat and uneven terrains. The new robot, combining the advantages of parallel robot and walking robot, has a large carrying capacity, strong passing ability, flexible turning ability, and simple gait control for its deployment for uneven terrain.