This paper presents a device for measuring and maintaining the constant water level in a tank. The device uses a capacity sensor to measure the water level. The sensor has a DC voltage output proportional to the water level in the tank. This voltage can be used in other automation too. The water level, in percentages, is displayed on a vu meter with 8 LEDs. The circuit for maintaining the constant level consists in a comparator with hysteresis. The level of the water is adjustable, using a reference voltage from a potentiometer (marked in percentages). The level of the water is compared with the prescribed level and the difference between them commands the start/stop of the water pump which supplies the tank through a relay. The device is powered by 220 V and is isolated from the environment.

In this study, the effect of ZnO nanoparticles (Zn NPs) on the performance of epoxy resin composites was investigated. The new ZnO/epoxy resin composites were synthesized using halloysite nanotubes (HNT) and different types of ZnO nanoparticles (commercial ZnO and ZnO-ODTES). These ZnO nanoparticles were utilized for intending to enhance the interfacial bonding between the epoxy resin and the reinforcement. Various methods such as FTIR, TGA, DSC, TEM-EDX, and Nanoindentation analyses were used to prove that the ZnO nanoparticles can improve the properties of epoxy resin composites. The thermal properties of the epoxy resin composites were enhanced to a greater extent by the addition of ZnO NPS. DSC testing proved that the epoxy resin composites modified with ZnO NPS are more flexible and elastic than unmodified epoxy resin. It was seen that the epoxy resin modified with ZnO-ODTES shows a much improved hardness and penetration depth compared to the other samples. These findings can pave the way for the developing of ZnO-based marine coatings with improved properties.

The study's objective was to investigate changes in the fatty acid composition of cow milk in general and in 80 Romanian Spotted cows' husbandry and feeding systems in particular (grazing – GC group vs. stabulation – SC group). The ultimate objective was to determine if the changes that happened in the milk also transferred to the finished product. Also, the influence of the raw milk quality produced by both systems was evaluated when yogurt was made from it. The milk was gathered in May, July, and September and used for both the yogurt-making process and the study, which lasted from May to October. As comparison to milk from SC, milk from grazed caws had larger percentages of fat and dry matter throughout the summer (GC) season. Moreover, pasture-based rations (MGC) contained more PUFA than MCS did. Data research revealed that not only do factors like milk origin and initial quality have a substantial impact on yogurt quality parameters, but also technologies like milk fermentation have a considerable impact on the fatty acid profile of yogurt. As comparison to cows kept permanently in stables, grazed cows (MGC) had fat with a lower concentration of saturated fatty acids and a higher proportion of rumenic, vaccenic, and oleic acids (MSC). When fresh milk is processed into yogurt and other dairy products, the fatty acid profiles alter, with saturated fatty acids predominating over unsaturated ones. The findings show that pasture-fed cows have a positive impact on milk quality, particularly in terms of fatty acid profile, as well as on yogurt's ultimate nutritional and dietary quality.

It is widespread to examine and explain the functioning of the standard “Current Doubler Rectifier” as strictly symmetrical according to the electrical current through the two inductances. The present work challenges this consideration and proposes a new version of the electrical circuit daigram where the current symmetry is improved. The proposed circuit is called “Improved Current Doubler Rectifier”.

We consider a multitude of topics in mathematics where unification constructions play an important role: the Yang–Baxter equation and its modified version, Euler’s formula for dual numbers, means and their inequalities, topics in differential geometry, etc. It is interesting to observe that the idea of unification (unity and union) is also present in poetry. Moreover, Euler’s identity is a source of inspiration for the post-modern poets.

This paper is referred to a top frontline research in life science, showing that in spite of the large variation of the physiological architecture and behavioral forms of the living systems, the fundamental structure of their informational system is basically the same, allowing the body growth/development by micro to macro-structuration processes, maintaining the same informational configuration and functions like the basic unit of life – the eukaryotic cell. Starting and based on the determination of the special/specific info-operability in living structures and the role of information in structuration and their functionality, there are discussed the informational functions of the eukaryotic/prokaryotic cells, the simplest units of life and is elaborated and presented the Informational Model of the Living Structures, showing that these structures operate on the basis of two main informational systems: one of them defined as the Programmed Informational System, composed by three components, assuring respectively the info-generation, maintenance and the proliferation/reproduction, and another one defined as the Operative Informational System, necessary for the continuous communication with the environment for adaptation, consisting in four main components referred to memory, decision, sentience and info-connection/info-selection. The revealed properties are compared with the Informational System of the Human Body, as a prototype of a living system on the top of the evolutionary scale, showing/demonstrating the compatibility of structuration and functions on the entire scale, from prokaryotic/eukaryotic unit cells to multicellular organisms – plants, animals and human, by means of a continuous adaptation process, which always follows the same line of micro to macro-structuration process based on the same Info-organization and functionality. These models are new and revolutionary in the information and life sciences

This paper is based on a talk given at the 14-th International Workshop on Differential Geometry and Its Applications, hosted by the Petroleum Gas University from Ploiesti, between July 9-th and July 11-th, 2019. After presenting some historical facts, we will consider some geometry problems related to unification approaches. Jordan algebras and Lie algebras are the main non-associative structures. Attempts to unify non-associative algebras and associative algebras led to UJLA structures. Another algebraic structure which unifies non-associative algebras and associative algebras is the Yang-Baxter equation. We will review topics relared to the Yang-Baxter equation and Yang-Baxter systems, with the goal to unify constructions from Differential Geometry.

We consider several unification problems in mathematics. We refer to transcendental numbers. Also, we present some ways to unify the main non-associative algebras (Lie algebras and Jordan algebras) and associative algebras.

Based on some experiments, the paper describes with the help of polarization the physic-chemical processes that take place in the contact area of friction pairs, during the selective transfer as a result of the change in the input speed of the lubricant (glycerin), as well as how it influences their wear. Through polarization, the quantitative and qualitative transformations of glycerin are studied during frictional stress with selective transfer, the determination of the properties of the selective solution, and the damage to the metals and alloys of the friction pairs, but also after frictional stress.

Background. Moral distress (MD) and Burnout of Health Care Personnel (HCP) were extensively studied during the pandemic. However, little information is available about their prevalence after its decline. This study assesses the prevalence of MD, and burnout after the decline of the pandemic. Methods. The British Medical Association questionnaire referring to MD and the Maslach Burnout questionnaire were addressed to the hospital’s personnel. Results. 516 valid questionnaires were included in the study. Nurses’ participation rate was 67% and doctors 41%. MD was identical among doctors and nurses 73,8%, and in decremental order factors contributing to MD are insufficient staff, mental fatigue, and physical fatigue. Participants believe that more staff, less bureaucracy, and greater emotional support would alleviate MD. Doctors score higher than nurses for lack of time to give sufficient support to patients and public health decisions affecting communities. To alleviate MD, doctors ask for more ethical and legal support, more funding and working fewer hours. Nurses score high on emotional exhaustion and depersonalization. Conclusions. MD and burnout persist among HCP after the decline of the pandemic. Participants believe that institutional and public health decisions would help alleviate MD. Leaders and institutions must provide more supportive environments to moderate MD.

Abstract: Background and Objectives: A growing number of epidemiologic studies have found that diabetes mellitus may increase cancer risk and is implicated in numerous other metabolic and inflammatory disorders. The increase in pro-inflammatory cytokines plays a major role in insulin resistance and leads to hypoalbuminemia, and micro- and macrovascular diabetes complications, including kidney disease and anemia. This study aimed to investigate the utility of CEA, CRP, serum albumin level, hemoglobin, and LDH as biomarkers for cancer risk and the biological implications of diabetes on the evolution and prognosis of oncological patients. Material and methods: We conducted a retrospective, longitudinal, observational study, on a total group of 434 patients, 217 diagnosed with a form of cancer and with type 2 diabetes as a comorbidity, and the other 217 – control group, without diabetes. These patients were admitted to the oncology clinic. In subgroups, the same number of patients was considered, depending on the location of the oncological pathology. Anemia, hypoalbuminemia, elevated lactate dehydrogenase, glycated hemoglobin, and C-reactive protein levels are more pronounced in subjects with type 2 diabetes and cancer. Conclusions: The presence of diabetes negatively affects the clinical and biological prognosis of cancer patients.

We aimed to reveal the disease burden of aphasia after acute ischemic stroke (AIS) at the national level and investigate the impact of aphasia on tertiary care resources and patient outcomes. The local database from the Cluj-Napoca Emergency County Hospital (CNECH), the second largest stroke center in Romania was used to export demographics, baseline clinical and laboratory data, inpatient length of stay (LOS), NIH Stroke Scale (NIHSS), and discharge modified Rankin Scale (mRS) score data for all AIS patients admitted during March 2019. Of 92 patients included in the study, 30 (32.6 %) had aphasia on admission. In a marginally significant unadjusted hierarchical multiple regression model, individuals with aphasia had a LOS of 1.86 days longer than stroke survivors without aphasia. In an adjusted version of the model, the NIHSS score at baseline was a significant predictor for LOS. In addition, the presence of aphasia was associated with a 1.49 increase in the mean mRS score. Aphasia was a marginally significant predictor for increased LOS. Presence of aphasia was more likely to produce a poor functional outcome. Considering an estimated impact of approximately EUR 3 million on direct medical expenditure annually, future policymaking efforts should improve prevention of stroke and improved access to post-stroke aphasia care in Romania.

Over the last few decades, ocean research and exploration have made underwater mechanical systems a necessity. Underwater vehicles provide a new kind of marine platforms that could represent a great necessity in many areas of oceanographic research. Until now, the underwater vehicles come in a verity of shapes, sizes and means of propulsion. Depending on these characteristics, the type and mission of the vehicle are also determined. The underwater robots are used for different inspection and intervention missions in e.g. the oil and gas industry, ocean science research. Due to multiple applications to which the vehicle can participate, it can be successfully used and to determine methods of re-use of marine energy. Environmental mapping provides accurate information about the main areas of interest of the energy, as well as the exploitation possibilities of that. Most of the time, biomimetic robots were inspired their senso structure, from different kind of animals, such as insects, fish and birds. Nowadays, the concept of a underwater robotic vehicles capable to move independently, autonomously or remotely, has a great potential and a large application. This is the reason that the last studies have been directed on biomimetic robots. The fish and other underwater animals have evolved superior swimming capabilities in many ways and represent a starting point to explain the fluid-mechanical principles. Furthermore, the underwater animals develop and achieve extraordinary propulsion efficiencies, acceleration and maneuverability. They can also achieve high speed under water. Implanting and creating a vehicle through a biomimetic approach reduces the energy used to maneuver the vehicle as it can automatically correct its position and displacement. The paper presents an examination of the state of biomimetic robotic fishes, underlining the reason why bio-inspiration can help us in the underwater locomotion technology.

As a service business models have been ranked by management consultants the management innovation of 2020, and yet are scarcely theorized. Therein, value stipulations in customer contracts lead to the shift from product to service. However, there is no available research about the nature, formula and decisional process about these value stipulations. The motive for this research is to fill in this gap. The goal is to provide first insight about value stipulations in as a service business models: their formula and decisional methodology. The article is a multiple theory building case study on leading platform as a service providers, which aims to contruct the paradigm of the value decision methodology to invest in this technology by purchasing it from dedicated vendors. The methodology works to identify the management instruments involved in the decisional activities to invest in digital technology, where each management instrument is assumed to match an activity at seller and buyer; the sequence of the activities using the Critical Path Method gives the decisional process. Dependent variables are the elements of the as a service business contracts: the customer offering (product-service solution) and the value created, captured and delivered by the solution. Independent variables are given by empirical data analysis. Findings show a relationship between dependent variable value in the as a service business model contracts and independent variables governance objective, strategy, as a service business model type, activity management techniques (roadmap, program, project, operations, lean start-up), capital allocation techniques (equity, debt, options, venture capital typology). If innovation is exploitative, then the customer offering is known and value is determinable via roadmap – project management techniques (program, project, an operations) and capital allocation techniques for precictable environment, If innovation is radical, then the customer offering is not known and value is a target used to architect the solution via lean start-up innovation techniques funded by venture capital. The contribution is a new theoretical construct and deep insight into the practice of digital transformation considering all inherent issues.

This paper delves into the multifaceted domain of the aerospace industry, examining its evolution, current challenges, and imperative focus on quality management and process integration. The aerospace sector, driven by technological advancements and a burgeoning global demand for air travel and freight transport, necessitates a thorough analysis of its industrial fabric and operational intricacies. This research endeavors to analyze the dynamics of the aerospace industry, pinpoint its challenges, and propose an integrated approach to enhance efficiency, quality, and sustainability. The primary goals encompass understanding the evolving industry landscape, identifying critical challenges, and offering innovative solutions by amalgamating principles of Industry 4.0 into quality management and processes within the aerospace sector. Through an in-depth exploration of various facets, this research underscores the pivotal role of efficient processes and integrated quality management in achieving sustainable growth and competitiveness in the aerospace industry. By aligning with the paradigm of Industry 4.0, organizations can optimize their operations and contribute to the industry's advancement, delivering safer and more cost-effective aerospace products. The study adopts a multifaceted approach, incorporating extensive literature review, critical analysis of industry trends, examination of quality management frameworks, and a thorough evaluation of the integration potential of Industry 4.0 technologies. The research also involves case studies and expert insights to validate the proposed approach. The investigation reveals that by leveraging Industry 4.0 technologies and embracing an integrated approach to quality management, the aerospace industry can significantly enhance operational efficiency, product quality, and overall sustainability. The seamless integration of processes and the implementation of advanced quality frameworks pave the way for a more competitive and future-ready aerospace industry, meeting the evolving demands of a globalized world.

Soft magnetic composites cores were produced by Spark Plasma Sintering (SPS) from Ni3Fe@ZnFe2O4 and NiFeMo@ZnFe2O4 pseudo-core-shell powders. In the Fe-Ni alloys@ZnFe2O4 pseudo-core-shell composite powders, the core is a large nanocrystalline Permalloy or Supermalloy particle obtained by mechanical alloying, and the shell is a pseudo continuously layer of Zn ferrite particles. The pseudo-core-shell powders have been compacted by SPS at temperatures between 500-700 ºC, with a holding time of 0 minutes. Several techniques were used for the characterisation of the powders and sintered compacts: X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, magnetic hysteresis measurements (DC and AC) and electrical resistivity. The electrical resistivity is stabilised at values of about 7·10-3 Ω·m for sintering temperatures between 600-700 °C and this value is 3 orders of magnitude higher than the electrical resistivity of sintered Fe compacts. The best relative initial permeability was obtained for the Supermalloy/ZnFe2O4 composite compacts sintered at 600 ºC, which decreases linearly for the entire frequency range studied, from around 95 to 50. Up a frequency of 2,000 Hz the power losses are lower than 1.5 W/kg. At the frequency of 10 kHz, the power losses are larger, but they remain at a low level. In the case of Supermalloy/ZnFe2O4 composite compact SPS-ed at 700 °C, the specific power losses are even lower than 5 W/kg. The power losses decomposition proved that intra-particles losses give the main part of the losses.

Bringing toghether mathematical and philosophical ideas related to transcendental numbers, this paper begins with a survey on transcendence and transcendental numbers, it then presents several properties of the transcendental numbers e and π, and then it gives the proof of a new inequality for transcendental numbers. Also, in relationship with these topics, we study solutions to the Yang-Baxter equation from hyperbolic functions and from logical implication.

The subject of this paper is to analyse the Math Principia of Economic 3D Black Holes in Roegenian economics. This idea is totally new in the related literature, excepting our papers. In details, we study two special problems: (i) math origin of economic 3D black holes, (ii) entropy and internal political stability depending on national income and the total investment, for economic RN 3D black hole. To solve these problems, it was necessary to jump from macroeconomic side to microeconomic side (a substantial approach so different), to complete the thermodynamics-economics dictionary with new entities, to introduce the flow between two macroeconomic systems, to study the Schwarzschild type metric properties on an economic 4D system, together with Rindler coordinates, Einstein 4D PDEs, and economic RN 3D black hole. In addition, we introduce some economic Ricci type flows or waves, for further research.

The present article seeks to analyse the period 1938-1940, when the Romanian interwar democracy was suspended through the promulgation of the anti-liberal Constitution of 27 February 1938. The Constitution abolished the political parties and trade unions, replacing them with new institutions established according to royal decrees: the royal single party, known as the National Renaissance Front (Frontul Renaşterii Naţionale, FRN) and corporations of workers and employers, respectively. Starting from that moment, the regime, through its representatives, made recourse to a nationalist rhetoric directed against the democratic parliamentary system. Moreover, a cult of personality of the monarch can be identified in the speeches of the royal corporatist ‘parliament’, as well as in the doctrine of FRN and the Nation’s Party (its successor), but also in the regime’s youth organisation, ‘The Country’s Sentinel’ (Straja Ţării), whose First Sentinel was the authoritarian monarch himself. Thus, the cult of personality of Carol II represented one of the sources of inspiration for the dictator Nicolae Ceauşescu and for the leaders of this totalitarian regime.

The purpose of the research was to obtain information about the necessity and efficiency of the application of localized irrigation to some qualitative indices of plum trees in the nursery, against the background of different fertilization treatments. The expected results to be obtained by applying differentiated rules of irrigation and fertilization will consist in obtaining a healthy, vigorous fruit tree planting material, increasing production in the nursery. With fruit trees in the nursery, as with all cultivated plants, the growth process depends to the greatest extent on the climate and soil conditions available to them. The use of fertilizers in tree culture becomes necessary to renew the reserve of nutrients consumed by plants or leached in depth, then to improve the physical condition, the chemical composition, and the overall state of fertilization of the soil. It is necessary to intervene every year, in several rounds, with fertilizations that ensure, on the one hand, the achievement of a certain level of production, and on the other hand, a certain level and ratio of nutritional elements by returning the amounts of elements easily accessible nutrients extracted with the harvest to be able to maintain, in this way, the fertility of the soil in accordance with the age of the plantation and the level of production. The two varieties of plum studied were Stanley and Cacanska Lepotica, two valuable varieties for the quality of the fruit. During the research, the fertilization treatments had the highest contribution (34.50 %) on the stem diameter, compared to irrigation (20.67 %) and respectively the variety (5.63 %), considering that the variety did not significantly influence the increase in diameter of the grafted trees.

We studied Ni2FeSi, Co2FeSi and Co2MnSi -based full Heusler alloy glass-coated microwires with the same geometric aspect ratio ρ ≈ 0.50 ± 0.01 prepared using Taylor-Ulitovsky method. The fabrication of X2YZ; (X = Co & Ni, Y = Fe & Mn and Z = Si) based glass coated microwires with fixed aspect ratio is a quite challenging due to the different samples preparation conditions. The XRD analysis shows nanocrystalline microstructure for all the samples. Space group Fm3¯m (FCC) with disordered B2 and A2-types for Ni2FeSi and Co2FeSi and ordered L21-type for Co2MnSi are observed. The change in the positions of Ni, Co and Mn, Fe in X2YSi resulted in a variation in the lattice cell parameters and the average grain size of the sample. Room temperature magnetic behavior shows a dramatic change depending on the chemical composition, where Ni2FeSi-MWs shows the highest coercivity (Hc) compared to Co2FeSi-MWS and Co2MnSi-MWs. The Hc –value of Ni2FeSi-MWs is 16 times higher than that of Co2MnSi-MWs and 3 times higher than that of Co2FeSi-MWS. Meanwhile, the highest reduced remanence is reported for Co2FeSi-MWS (Mr =0.92), , being about 0.33 and 0.22 for Ni2FeSi-MWs and Co2MnSi-MWs, respectively. From the analysis of the temperature dependence of the magnetic properties (Hc and Mr) of X2YZ-MWs we deduced that Hc shows a stable tendency for Co2MnSi-MWs and Co2FeSi-MWs, meanwhile two flipped points are observed for Ni2FeSi-MWs where the behavior of Hc changes with temperature. For Mr monotonic increase by decreasing the temperature is observed for Co2FeSi-MWs and Ni2FeSi-MWs and roughly stable for Co2MnSi-MWs. The thermomagnetic curves at low magnetic field show irreversible magnetic behavior for Co2MnSi-MWs and Co2FeSi-MWs and regular ferromagnetic behavior for Ni2FeSi-MWs. The current result illustrates the ability to tailor the structure and magnetic behavior of X2YZ-MWs at a fixed internal stresses, i.e., with fixed aspect ratio. Additionally, a different behavior was revealed in X2YZ-MWs depending on the degree of ordering and elements distribution. The tunability of magnetic properties of X2YZ-MWs makes them suitable for sensing applications.

The role of the databases is to allow persisting data, no matter if they are of the SQL or NoSQL type. In SQL databases, data is structured in a set of tables in the relational database model, grouped in rows and columns. The CRUD operations (create, read, update, and delete) are used to manage the information contained in the relational databases. Several dialects of the SQL language exist, as well as frameworks for mapping Java classes (models) to a relational database. The question is what we should choose for our Java application and why. A comparison between the most used relational database management systems, mixed with the most used frameworks should give us some guidance about when to use what. The evaluation is done on timing for each CRUD operation, from thousands to millions of entries, using the possible combinations between the relational database system and the framework. The experiments included the possibilities to warm up the Java Virtual Machine before the execution of the queries. Also, the research investigated the time spent inside different methods of the code, to determine the critical regions. Thus, the conclusions provide a comprehensive overview of the performances of Java applications accessing databases depending on the suite of decisions considering the database type, the framework in use, the type of operation, and supporting architects and developers for their technological decisions and for improving the speed of their programs.

Cardiac amyloidosis (CA) is a restrictive cardiomyopathy characterized by deposition of amyloid in the myocardium and recent studies revealed it is more frequently seen than we thought. Advances have been made over the last years, but a delayed diagnosis is frequently seen. An online survey was conducted among cardiologists from Romania representing the first assessment of the knowledge of CA among them with 195 cardiologists answering the questionnaire. There was a wide variation in their knowledge regarding CA. Our participants had few experience with CA and reported a significant delay between first cardiac symptom and diagnosis. Around one half of them did not seem familiar with the noninvasive diagnostic algorithm and with the wild-type transthyretin amyloidosis (ATTRwt). Even the participants who are aware of this condition and the available treatment options stated this is a rare disease and there is no disease modifying treatment available for ATTRwt. Awareness among cardiologists is the most important challenge in diagnosing CA. Romanian cardiologists are partially aware of this topic, but there are still gaps in their knowledge. Educational programs can improve screening of patients with a high suspicion for this progressive condition whose evolution has been dramatically changed by the new treatment options.

The interaction between O2 and reduced ceria nanocubes was mainly investigated by FTIR spectroscopy. Nanorods and nanoparticles were also studied for comparison. Adsorption of O2 at 100 K on unreduced ceria produces only O2 molecularly adsorbed on Ce4+ sites. The Ce3+ cations in H2-reduced ceria were monitored by the 2F5/2 → 2F7/2 electronic transition band at 2133-2095 cm-1. This band possesses a fine structure well resolved at 100 K. The positions of the individual components depend on the Ce3+ environment, including the presence of nearby species such as OH groups. Even at 100 K, the interaction of O2 with reduced ceria leads to fast oxidation of about half of the Ce3+ cations, including all Ce3+ sites bound to OH groups and carbonates, and the simultaneous formation of superoxo (O2) and peroxo (O22) species. The remaining fraction of Ce3+ sites disappears upon heating up to 348 K. At higher temperatures, the peroxo species decompose directly, yielding lattice oxygen. Superoxides are converted to hydroperoxides, which then decompose to terminal OH groups. Reduced samples evacuated at T < 773 K contain sorbed H2. Part of this hydrogen is also fast oxidized to H2O even at 100 K.

This research delves into the intricate dynamics underlying the impact of investments on global output, em-ploying the Leontief matrix as a robust analytical framework. Investments wield a profound influence on economies worldwide, with varying effects contingent upon investment types, development levels of coun-tries, and external factors such as trade conflicts and global shocks. The diverse range of investment forms, including physical capital, human capital, R&D, and technological investments, engenders distinct implica-tions for productivity, innovation, and efficiency. Developing and developed economies navigate unique tra-jectories, with investments playing a pivotal role in bridging infrastructure gaps, improving technology, and spurring growth. However, external disruptions, such as trade wars and global shocks, introduce an element of complexity, reshaping investment patterns and altering global output trajectories. This study centers on harnessing the Leontief matrix's prowess to evaluate the interplay of investments and global output, focusing on the Romanian economy. By analyzing input-output tables, encompassing 105 branches aggregated into 10 sectors, the research captures the intricate connections between economic segments. No-tably, the Romanian context reveals the volatility of the matrix coefficients', an outcome of ongoing transi-tional processes, technological advancements, and fluctuating relative prices. In unraveling the intricate threads weaving investments and global output, this study contributes to a nuanced comprehension of these multifaceted interactions. The findings underscore the significance of tailoring investment strategies to specific economic contexts and advocate for robust frameworks, such as the Leontief matrix, to inform pol-icy decisions and drive sustainable growth in an increasingly complex global economy.

COVID-19, the infectious disease caused by severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2), is frequently associated with pulmonary thrombotic events, especially in hospitalised patients. Severe SARS-CoV-2 infection is characterized by a proinflammatory state and an associated disbalance in hemostasis. Immune pathology analysis supports the inflammatory nature of pulmonary arterial thrombi composed by white blood cells, especially neutrophils, CD3+ and CD20+ lymphocytes, fibrin, red blood cells and platelets. Immune cells, cytokines, chemokines and the complement system are key drivers of immunothrombosis, as they induce the damage of endothelial cells and initiate pro-inflammatory and pro-coagulant positive feedback loops. Neutrophil extracellular traps induced by COVID-19-associated “cytokine storm”, platelets, red blood cells, and coagulation pathways close the inflammation-endotheliopathy-thrombosis axis, contributing to SARS-CoV-2 associated pulmonary thrombotic events. The hypothesis of immunothrombosis is also supported by the minor role of venous thromboembolism, chest CT imaging data showing peripheral blood clots associated with inflammatory lesions and the high incidence of thrombotic events despite routine thromboprophylaxis. Understanding the complex mechanisms behind COVID-19-induced pulmonary thrombosis will lead to future combination therapies for hospitalised patients with severe disease, that would target the crossroads of inflammatory and coagulation pathways.

Drilling vibrations has been identified as a key performance limiter that prevents successful energy transfer from the surface to the bit. The resultant irregular bit rotation speed causes drilling challenges like poor hole quality and reduction in rate of penetration to name a few. Amongst other vibration suppression techniques, active control of vibrations is widely used and recommended. Active control system utilizes a closed loop feedback control to continuously adapt to downhole vibrations detected at the surface. The system requires regular tuning and upgrades which is done experimentally before field deployment. The paper presents a PID based experimental tuning of horizontal and vertical strings for irregular RPM. In doing so, the paper highlights the need of having horizontal experimental setups for state-of-the-art PID tuning for downhole RPM. The settling time of irregular RPM for horizontal setup is found to be lower than the vertical configuration due to multiple contact points and increased friction coefficient.

Colloidal quantum dots (CQDs) are valuable for their potential applications in optoelectronic devices. However, they are susceptible to thermal degradation during processing and while in use. Mitigating thermally induced sintering, which leads to absorption spectrum broadening and undesirable changes to thin film electrical properties, is necessary for the reliable design and manufacture of CQD-based optoelectronics. Here, low temperature metal-oxide atomic layer deposition (ALD) was investigated as a method for mitigating sintering while preserving the optoelectronic properties of mercury telluride (HgTe) CQD films. ALD-coated films are subjected to temperatures up to 160oC for up to 5 hours and alumina (Al2O3) is found to be most effective at preserving the optical properties, demonstrating the feasibility of metal-oxide infilling to protect against sintering. HgTe CQD film electrical properties were investigated before and after alumina ALD in-filling, which was found to increase the p-type doping and hole mobility of the films. The magnitude of these effects depended on the conditions used to prepare the HgTe CQDs. With further investigation into the interaction effects of CQD and ALD process factors, these results may be used to guide the design of CQD-ALD materials for their practical integration into useful optoelectronic devices.

Introduction: The identification of some prognostic markers in head and neck cancers (HNC) is necessary for the stratification of the therapeutic approach with benefits in increasing treatment response rates and limiting the toxic side effects of treatments. Neutrophil-to-lymphocyte ratio (NLR), lymphocyte-to-monocyte ratio (LMR) and pallets-to-lymphocyte ratio (PLR) are currently validated as cheap and accessible biomarkers in different types of solid tumors. The purpose of the study was to evaluate the possible biomarker value of NLR, PLR and MLR recorded pre-treatment (radiotherapy/chemotherapy) for prognostic purposes in HNC. Materials and methods: The study included 190 patients with HNC included in the oncology record in the oncology outpatient clinic of the Craiova County Emergency Hospital starting from January 2002 and deceased until December 2022. Among them, 40 patients treated multimodally in the Clinic were included in the study of Oncology of the Craiova County Emergency Hospital for which the pre-treatment value (chemotherapy/radiotherapy) of NLR, PLR and MLR could be calculated. Overall survival (OS) values were correlated with NLR, PLR and MLR. Results: Median values for NLR, PLR and MLR were 6.15 (1.24-69), 200.79 (61.3- 1775.0) and 0.53 (0.12-5.5) respectively. In the study, the mean values for NLR, PLR and MLR of 2.88, 142.97 and 0.36 respectively were obtained. Median OS in the study group was 11 months (1-120). Although a negative Pearson`s correlation, the relationship between your variables was only weak, values R =.07, p=.67; R=.02, p=.31 and R=07, p=.62 being related with NLR, PLR and MLR respectively correlation with overall survival (OS). The median values of NLR, PLR and MLR were calculated (1.53, 90.32 and 0.18 respectively) for HNC cases with pre-treatment values of NLR <2 and for HNC cases with NLR values ≥6 (23.5, 232.78 and 0.79 respectively). Median OS for cases with NLR<2 and NLR≥6 were 17.4 and 13 months, respectively. Conclusions: The negative correlations of NLR, PLR and MLR with OS reported in the study are in accordance with the data reported in the literature for locally advanced recurrent and metastatic HNSCC cases. The comparative analysis of the data in the group with NLR<2 and NLR≥6 highlights an advantage of 4.4 months in median OS in favor of the group with low values of NLR. Being cheap and accessible, these markers could change the therapeutic approach even in centers with limited resources. The role of borderline NLR values as a prognostic factor in HNSCC must also be defined. PLR and MLR are less evaluated as biomarkers but the study demonstrates their potential to be used as prognostic biomarkers, it remains to be clarified if their inclusion in multivariable models along with NLR would bring a benefit

Aspartame is the methyl-ester of the aspartate-phenylalanine dipeptide. Over time it became a very popular artificial sweetener. However, since its approval by the main food safety agencies, several concerns have been raised related to neuropsychiatric effects and neurotoxicity, due to its ability to activate glutamate receptors, as well as carcinogenic risks by increased production of reactive oxygen species. Within this review we critically evaluated reports concerning the safety of aspartame. Some studies evidenced subtle mood and behavioral changes upon daily high-dose intake below the admitted limit. Epidemiology studies also evidenced associations between daily aspartame intake and higher predisposition for malignant diseases like non-Hodgkin lymphomas and multiple myelomas, particularly in males, but association by chance still could not be excluded. While the debate over the carcinogenic risk of aspartame is ongoing, it is clear that its use may pose some dangers in peculiar cases, such as patients with seizures or other neurological diseases; it should be totally forbidden for patients with phenylketonuria, and reduced doses or complete avoidance are advisable during pregnancy. It would be also highly desirable for every product containing aspartame to clearly indicate on the label the exact amount of the substance and some risk warnings.

The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

This work promotes new methods in Mathematical Modeling, consisting in the use of the methods of Non-standard Analysis in Topoi, having as its main purpose, the mathematical definitions of the pseudoparticles from the title, with arguments from Biology/Physiology (Mathematical Neuroscience), Physics (String Theory and Emergent Quantum Mechanics), and Cybernetics (Global Brain, including Natural and Artificial Intelligence). The connections between brain and mind will be scketched via the genetic/epigenetic interplay. The topoi model the intuitionistic logic (multi-valued) and have been used in Quantum Physics while Non-Standard Analysis in SET (= the Category of sets) has been applied in Mathematical Economics; topics from Theory of Categories were also used in the study of Consciousness; however, the combination topoi - non-standard analysis was never used until now in Applied Mathematics. Another important objective is to produce progress in this aria of Pure Mathematics also - the build of non-standard analysis in classes of topoi, already used in Physics. We propose the logic of non-standard extensions in topoi as a model of the human thinking (based on infons/receptons), these theories representing new top and very difficult results in Abstract Mathematics either.

We used the Taylor-Ulitovsky Technique to prepare nanocrystalline Co2MnGe Heusler alloy glass-coated microwires with a metallic nucleus diameter of 18 ± 0.1 µm and a total diameter of 27.2 ± 0.1 µm. Magnetic and structural studies were carried out to determine the fundamental magneto-structural characteristics of Co2MnGe glass-coated microwires. XRD revealed a well-defined nanocrystalline structure with average grain size about 63 nm, lattice parameter a = 5.62 and a unique mixture of L21 and B2 phases. The magnetization curves for field cooling and field heating (FC-FH) demonstrate a considerable dependence on the applied magnetic field, ranging from 50 Oe to 20 kOe. Internal stresses, originated by the production process, resulted in various magnetic phases, which were responsible for the notable difference of field cooling (FC) and field heating (FH) curves on magnetization dependence versus temperature. Furthermore, the ferromagnetic behavior and expected high Curie temperature together with high degree of L21 ordered makes it a promising candidate for many applications.

Nocardia is an emerging bacterial disease that often affects patients with compromised immune systems. As survival increases, more and more patients are receiving solid organ transplantations, and more patients are cancer survivors and receiving long-term immune system modifying agents or corticotherapy and immunosuppressive agents, organisms that are not harmful in usual circumstances become a public health problem. Carbapenems are usually a second-line therapy in the setting of Nocardia infections. We present the case of a patient who had an immunocompromised status and was diagnosed with Nocardia farcinica, which showed in vitro resistance to carbapenems. The symptoms were non-specific and had a common presentation, although the infection was disseminated and had severe CNS and ocular involvement. The clinical course was more severe when the carbapenem was withdrawn based on the provided antibiogram and markedly improved when clinical judgment considered it might be beneficial. The first case in our region to describe an „in vitro” carbapenem-resistant Nocardia species, that responded „in vivo” differently and we believe it is important to remind clinicians of this potentially severe disease in difficult cases.

Chondrosarcoma, represents approximately 0.1% of all neoplasms of the head and neck, being considered a rare disease, but with a relatively good prognosis. The 5-year overall survival (OS) rate is estimated at 70-80%, being considered a disease with a low growth rate. About 13% of all cases of chondrosarcoma, are located in the region of the head and neck. We present the case of a young patient treated multimodally, lost from the oncological records less than two years after the diagnosis, without evidence of disease progression. The early loss from the oncological follow-up programs of patients with a lower risk of early repalpse, without evidence of a recurrence or metastasis could be the consequence of a major complication among which we could assume an aspiration pneumonia secondary to a dysphagia, associated with an aggressive multidisciplinary treatment. Large tumor size and positive resection margins (R1 resection) are risk factors that support an intensive adjuvant approach in order to reduce the risk of recurrence, but the low grade of tumor, associating a lower risk of recurrence as well as the adverse events (AE) of adjuvant radiotherapy and chemotherapy justifies a more reserved therapeutic approach. Taking into account the longer life expectancy of these patients, it is recommended to use a more conformal irradiation technique in order to reduce doses to radiosensitive structures as well as to omit elective neck irradiation, taking into account the lower risk of lymph node involvement. The lack of guidelines that include very rare tumors including low grade chondrosarcoma of head and neck make a unified approach difficult, but the data presented even in case reports could contribute to choosing the regimen that offers the best therapeutic ratio.

Fatal hemoptysis secondary to severe pulmonary veins stenosis is an exceptional late complication of radiofrequency ablation for atrial fibrillation. We report the case of a 53-year-old male with a history of atrial fibrillation treated by radiofrequency ablation and admitted in our center 6 months after the initial procedure because of aggravating dyspnea and fatigability. Transthoracic echocardiography showed moderate dilation of right heart cavities, severe pulmonary hypertension, and a turbulent flow in superior pulmonary veins. The cardiologist suspected pulmonary vein(s) stenosis and cardiac computed tomography (CT) angiography was performed with findings of severe stenosis of the right superior, right inferior and left inferior pulmonary veins, near-occlusion of the left superior pulmonary vein and the vein draining the apical segment of the right lower lobe. The CT scan also revealed soft tissue attenuation of the mediastinum posterior to the left atrium suggesting fibrosing mediastinitis together with parenchymal findings consistent with pulmonary venooclusive disease and an area of hemorrhagic infarction. Fatal hemoptysis occurred 3 days after the evaluation before any treatment was attempted. In conclusion, severe pulmonary stenosis remains a rare but severe complication of radiofrequency ablation. Prevention is the key element together with an early diagnosis as the entity is potentially life-threatening.

Background: Androgenetic alopecia (AGA) and alopecia areata (AA) are most common types of non-cicatricial alopecia. Both diseases have limited effective therapeutic options and affect patients' quality of life. Pharmacogenetic tests can help predict the most appropriate treatment option by evaluating the single nucleotide polymorphisms (SNPs) corresponding to genes related to alopecia. The objective of the study was to evaluate and compare selected SNPs and genes in AA and AGA patients from Romania and Brazil. Materials and methods: We investigated associations between AA and AGA and 45 tag SNPs of 13 genes in 287 Romanian and 882 Brazilian patients. The DNA samples were extracted from saliva using qPCR technique. Results: GR-alpha gene, GPR44-2 gene, SULT1A1 gene and CRABP2 gene were statistically significantly different in Brazil compared to Romania. Minoxidil may be recommended in half of the cases of AGA and AA. Patients with AGA and high expression of SRD5A1 or PTGFR-2 may benefit from Dutasteride, respectively Latanoprost treatment. Most of the studied genes showed no differences between the two population. Conclusion: The DNA analysis of the patients with alopecia may contribute to a successful treatment.

This paper examines the use of multisensory virtual reality (VR) as a novel approach in psychological therapy for autobiographical memory retrieval with benefits for cognitive enhancement, stress reduction etc. The research in this paper was done under Romanian Arut Research Grant no. 27/09/10/2023 ”Intelligent VR system for treating autobiographical/episodic memory deficits".  By simulating realistic multisensory experiences, VR technology offers an immersive environment that surpasses traditional therapeutic methods in effectiveness. Previous studies demonstrate improved outcomes in treating various psychological conditions (affective disorders and PTSD, specific phobias and age-related cognitive decline). Technological advancements in VR, such as olfactory integration cand contribute to the realism and therapeutic potential of these environments, the integration of various physical stimuli with VR holds promising potential psychological therapies and highlighting the need for further interdisciplinary research. In this pilot study we tested the efficacy of a new system for triggering autobiographical memory retrieval. For this we used images combined with odors in a congruent manner and offering participants the chance to interact with the VR environment by using 2 virtual hands. We evaluated the efficacy of this system using qualitative methods with emphasis on the evaluation of the emotions associated with memory recollection and the ease of triggering memories. All participants in our pilot study experienced intense emotions related to childhood or adolescence and the pleasant feelings they had during the experiment persisted even after it ended. This is an advancement to what exists currently and original research elements for our paper.

The medical sector is of the utmost importance in every country for well-known reasons such as their economic development, national security, quality of life, and so on. Many researchers were dedicated to this topic, however, in Romania there are limited studies on this subject. One reason is that most of the businesses in this sector are individual enterprises or small family businesses. In our research paper we deploy several analysis methods to see the financial sustainability of companies operating in the medical industry. By analyzing a sample of 23931 companies and we have concluded that their performance has increase in the peak of the pandemic and that the financial stability is high. Our results are in line with other similar studies that were conducted in other regions.

This paper is a continuation of previous papers on unification theories publishes in AXIOMS. We present results about the (modified) Yang-Baxter equation, Euler’s formula, dual numbers, coalgebra structures, non-associative structures, differential geometry, and (mean) inequalities. We will also attempt to relate our discussion to some Brain Studies and Machine Learnig.

Applications in security and electronic surveillance require combination of excellent magnetic softness with good mechanical and anti-corrosive properties and low dimensionality. We overviewed the properties of soft magnetic glass-coated microwires and different post-processing making them quite attractive for electronic article surveillance and security applications. We studied the magnetostatic interaction between the microwires and routes to tune the non-linear hysteresis loops by using the arrays of different types of amorphous microwires. The presence of neighbouring microwire (either Fe or Co-based) significantly affects the hysteresis loop of the whole microwires array. In a microwires array containing magnetically bistable microwires we observed splitting of the initially rectangular hysteresis loop with a number of Barkhausen jumps correlated with the number of magnetically bistable microwires. Essentially, non-linear and irregular hysteresis loops have been observed in mixed arrays containing Fe and Co-rich microwires. The observed non-linearity in hysteresis loops allowed to increase the harmonics and tune their magnetic field dependencies. Non-linear hysteresis loops have been also observed upon devitrification of amorphous microwires. On the other hand, several routes allowing to tune the switching field by either post-processing or modifying the magnetoelastic anisotropy have been reviewed. Observed unique combination of magnetic properties together with thin dimensions and excellent mechanical and anti-corrosive properties provide excellent perspectives for the use of glass-coated microwires for security and electronic surveillance applications.

Energy-efficient microprocessors are essential for a wide range of applications. While near-threshold computing is a promising technique to improve energy efficiency, optimal supply demands from logic core and on-chip memory are conflicting. In this paper, we perform static reliability analysis of 6T SRAM and discover the variance among different sizing configuration and asymmetric minimum voltage requirements between read and write operations. We leverage this asymmetric property in near-threshold processors equipped with voltage boosting capability by proposing an opportunistic dual-supply switching scheme with a write aggregation buffer. Our results show that proposed technique improves energy efficiency by more than 21.45% with approximate 10.19% performance speed-up.

In current study we have obtained Co2FeSi-glass coated microwires with different geometrical aspect ratio, ρ = d/Dtot (diameter of metallic nucleus, d and total diameter, Dtot). The structure and magnetic properties are investigated at a wide range of temperature. XRD analysis illustrates a notable changing in the microstructure by increasing the aspect ratio of Co2FeSi glass coated microwires. Amorphous structure is detected for the sample with the lowest aspect ratio (ρ = 0.23), whereas a growth of crystalline structure is observed in the other samples (aspect ratio ρ = 0.30 and 0.43). This change at the microstructure properties correlates with dramatic changing in magnetic properties. For the sample with the lowest ρ -ratio, non-perfect square loops are obtained with low normalized remanent magnetization. A notable enhancement in the squareness and coercivity are obtained by increasing ρ -ratio. Changing the internal stresses strongly affects the microstructure, resulting in a complex magnetic reversal process. The thermomagnetic curves show large irreversibility for the Co2FeSi with low ρ -ratio. Meanwhile, if we increase the ρ -ratio, the sample shows perfect ferromagnetic behavior without irreversibility. The current result illustrates the ability to control the microstructure and magnetic properties of Co2FeSi-glass-coated microwires by changing only their geometric properties without performing any addition heat treatment. The modification of geometric parameters of Co2FeSi glass-coated microwires allows to obtain microwires which exhibit an unusual magnetization behavior that offers opportunities to understand the phenomena of various types of magnetic domain structures, which is essentially helpful for designing sensing devices based on thermal magnetization switching.

The grinding process by friction at the micro-scale in a mill with stones is considered a variable combination of contacts: with two-body (the asperities of lower millstone in direct contact with the asperities of upper millstone) and the three-body (micro-particles of ground seeds trapped between the asperities of lower and the upper stones of the mill). Three elements are described: (1) the mechanic contact of the asperities of the lower and upper millstone, to predict pressures on asperities, by modeling; (2) tests on a millstone sample covered with grinding particles, and (3) tests on a wafer sample formed by the millstones with the grinding particles between them. The paper highlights the combined effects of the micro-scale friction by individual measurements and to sum these effects an analytical model was used, and to validate the model, several experiments were performed. A suitable grind by friction assumes the grain’s movement and the interaction between the seeds and solid surfaces and is highlighted through theoretical and experimental studies. Topography analysis of the surface of the millstones revealed the model of microscopic frictional force. Endpoint measurements (the traces of the surface topography evolution), enable model verification in the grinding process.

We studied the effect of annealing and the applied magnetic field from 50 Oe to 20 kOe on the magneto-structural behavior of Ni2FeSi-based Heusler microwires fabricated by using Taylor-Ulitovsky technique. Using the XRD analysis, a strong effect of annealing, manifested as the development of the crystallization process, was observed. The average grain size and crystalline phase content of annealed sample increase from 21.3 nm and 34 % to 32.8 nm and 79%, respectively, as-compared to the as-prepared one. In addition, upon annealing phase transforms into a monoclinic martensitic structure with modulation 10M were observed, which cannot be found in the as-prepared sample. Concerning the magnetic properties, both samples show ferromagnetic behavior below and above the room temperature, where the Curie temperature of Ni2FeSi is higher than room temperature. The induced secondary phases have a noticeable effect on the magnetic behavior of the annealed sample, where a high normalized saturation magnetization (NMs) and low normalized reduced remenance (Mr = M/M5K), compared to the as- prepared have been detected. Additionally, the coercivity of annealed sample shows one flipping point at 155 K where it behavior with temperature is changed. Meanwhile, the as-prepared sample show two flipped point at 205 K and 55 K. A mismatch between field cooling (FC) and field heating (FH) magnetization curves with temperature has been detected for annealed sample at low applied magnetic field. In addition the FC and FH curves shows different slopes with variation the temperature and the magnetic field. By increasing the external magnetic field higher than 200 Oe and up to 20 kOe a gradual changing in the magnetic behavior has been detected, where the mismatch and different slopes disappeared at applying magnetic field about 20 kOe. The difference in magnetic and structure behavior of Ni2FeSi microwires sample is discussed considering the effect of induced internal stresses by the presence of a glass coating and the recrystallization and stresses relaxation upon annealing.

The present study illustrates the strong effect of geometrical parameters on the magneto-structural properties of Co2MnSi glass-coated microwires prepared using the Taylor-Ulitovsky method. Thus, two samples with different geometrical aspect ratios (ρ= d / D) have been fabricated, where d is the metallic nuclei diameter and D is the total diameter of the Co2MnSi microwire. The XRD analysis shows a significant change by modifying the aspect ratio, for ρ = 0.46 the main peak with miller indices (220) is recognized as an A2-type disordered cubic structure. Meanwhile, in the sample with a low aspect ratio, ρ = 0.31, the perfect L21 ordered cubic structure is attained. In addition, a decrease in average grain size from 36.62 nm to 28.07 nm by increasing the aspect ratio from 0.46 to 0.31 is observed. The magnetic characterization has been done in a wide range of temperatures and magnetic fields. Both of Co2MnSi samples show ferromagnetic behavior in a whole measuring temperatures range. A significant increase in coercivity and normalized reduced remanence by decreasing the aspect ratio is observed. The change in the magnetic properties is attributed to the modification in the microstructure, which is induced during the fabrication process. Such a dependence on the microstructure and magnetic properties on the ρ-ratio can be associated either with the internal stresses distribution and magnitude or with different quenching rates of microwires with different aspect ratios. The current findings demonstrate the tunability of microstructure and magnetic properties of Co2MnSi-glass-coated microwires simply, by a small modification in the geometric properties during the manufacturing process and without excreting any additional post-processing. The variation in geometric parameters of Co2MnSi glass-coated microwires allows us to tune magnetic properties and structure, which is essentially advantageous for sensing devices development.

In current work, we illustrate the effect of adding small amount of Carbon to very common Co2MnSi Heusler alloy based-glass coated microwires. A significant change in the magnetic and structure structural properties has observed for the new alloy Co2MnSiC compared to the Co2MnSi alloy. The magneto-structural investigations have performed to clarify the main phys-ical parameters i.e., structural & magnetic at a wide range of measuring temperature. The XRD analysis illustrated the well-defined crystalline structure with average grain size (Dg = 29.16 nm) and a uniform cubic structure with A2-type compared to the mixed L21 and B2 cubic structures for Co2MnSi-based glass coated microwires. The magnetic behaviour has investigated at a tem-perature range (5 to 300 K) and an external applied magnetic field (50 Oe to 20 kOe). The adding of small amount of Carbon to the Co2MnSi matrix enhance the magnetic thermal stability, where the thermomagnetic behaviour of Co2MnSiC glass-coated microwires show a perfect stable be-haviour for a temperature range from 300 K to 5 k, the differences between the coercivity value is only 0.3 Oe compared to 4 Oe for Co2MnSi-sample. In addition, M-H loops measured at tempera-ture below 50 K show unsaturated loops; meanwhile the Co2MnSi loops shows a strong antifer-romagnetic coupling for the loops measured below 50 K. By studying the field cooling (FC) and field heating (FH) magnetizations curves at a wide range of external applied magnetic field we detected a critical magnetic field (H = 1 kOe) where FC and FH curves have a stable magnetic behavior for Co2MnSiC sample, such stability does not find in Co2MnSi sample. We proposed a phenomenal expression to estimate the magnetization thermal stability, ΔM (%), of FC and FH magnetization curves and the maximum value is detected at the critical magnetic field where ΔM (%) ≈ 98 %. The promising magnetic stability of Co2MnSiC glass-coated microwires with tem-perature is due to the changing of the microstructure induced by adding Carbon, as the A2-type structure show a unique stability by variation the temperature and the external magnetic field. In addition, a unique internal mechanical stress, which induced during the fabrication process and plays on controlling magnetic behavior with temperature and external magnetic field. The ob-tained results make Co2MnSiC promising candidate for magnetic sensing devices based Heusler glass-coated microwires.

The emergence of M. tuberculosis strains resistant to Isoniazid (INH) and Rifampicin (RIF), the two most potent drugs of first-line anti-TB therapy is termed multidrug drug-resistant TB (MDR-TB). Multidrug-resistant tuberculosis has been a serious medical and epidemic problem all over the world. We present here a series of clinical cases consist of two patients diagnosed with isoniazid resistant tuberculosis. Histopathological examination supports the diagnosis of tuberculous granulomas. And the pathology molecular examination revealed the presence of Isoniazid-resistant Mycobacterium tuberculosis1,2 via the following mutation c.947G&gt;A; p.Gly316Asp. Isoniazid-resistance is associated with mutations in the furA-katG and fabG1-inhA operons, as well as mutations in the ahpC gene. 64% of the isoniazid-resistance phenotypes were associated with the katG315 mutation worldwide. The second most common mutation is inhA-15, and it has been reported in 19% of the Isoniazid-resistant isolates. The significant association between the two mutations, inhA c-15 and katG 315 respectively, and the high-level resistance is of interest in the interpretation of current and future molecular diagnostic testing, as an early prediction of the level of Isoniazid-resistance is essential to decide the benefit of high-dose Isoniazid use.

Incisional hernias have a particular dynamic related both to the repair method and to the absence or presence of a prosthetic material. The incidence of incisional hernias is estimated at 9.8% after 21 months and increases to 18.7% after ten years. This study presents a surgical method for the repair of recurrent incisional hernias, through open surgery and the use of existing mesh. The selection criteria regarding the use of this method are: the prosthesis is well integrated, without granulomas, suppurations, defect appearing on the same prosthetic abdominal area. The analyzed factors were the location of the incisional hernias, the duration of the operation, the duration of hospitalization, identified complications, the size of the parietal defect. The retrospective study carried out focused on recurrences of incisional hernias from a group of 631 patients operated on for incisional hernias in a general surgery department of Dr. Constantin Andreoiu County Emergency Hospital, Ploiești, Romania, during January 2018 - December 2022. Of the total of 18.22% relapses, 13.6% were relapsed eventrations after prosthetic procedures. Following the application of the selection criteria, several 8 patients with recurrent eventrations were operated by the open method using the existing mesh. In the case of recurrences after prosthetic procedures of incisional hernias, the recurrence can be solved by open surgery using the existing well-integrated prosthesis, without tension, absence of suppuration in the wound, and the peritoneal cavity. For the presented case, the return to daily activities occurred after 22 hours of hospitalization.

The processes of the sublimation and thermal decomposition of the 1‐ethyl‐3‐methylimidazolium hexafluorophosphate ionic liquid (EMImPF6) were studied by a complex approach including Knudsen effusion mass spectrometry, IR and NMR spectroscopy, and quantum chemical calculations. It was established that the vapor over liquid phase primarily consists of decomposition products under equilibrium conditions. Otherwise, the neutral ion pairs are the only vapor components under Langmuir conditions. To identify the nature of the decomposition products an experiment on the distillation of the ionic liquid was performed and the collected distillate was analyzed. It was revealed by the IR and NMR spectroscopy that EMImPF6 decomposes to substituted imidazole‐2‐ylidene (C6N2H10PF5) and HF. The measured vapor pressure of C6N2H10PF5 reveals a very low activity of the decomposition products (&lt;10–4) in the liquid phase. The absence of significant accumulation of decomposition products in the condensed phase makes it possible to determine the enthalpy of sublimation of the ionic liquid assuming its unchanged activity. The thermodynamics of the EMImPF6 sublimation was studied by Knudsen effusion mass spectrometry. The formation enthalpy of EMImPF6 in ideal gas state was found from combination of the sublimation enthalpy and formation enthalpy of ionic liquid in the condensed state. The obtained value is in good agreement with those calculated by quantum chemical methods.

In the current socio-economic context, pension systems have become a crucial topic in the agenda of governments and international bodies. In this paper, an empirical study regarding the economic and social sustainability of pension systems in Central and Eastern European Countries was performed. The goal of the research is to establish the sustainability of pension systems with econometric modeling techniques on three dimensions as the research hypotheses are revealed: first, by strengthening the financial soundness of pension systems; second, consolidating the economic environment of pension systems; third, increasing the degree of social security systems with a direct effect of reducing poverty. The results led to relevant insights emphasizing the need for more inclusive economic, financial, and social reforms. From a policy perspective, these findings could be a starting point for the enhancement of the financial adequacy and economic and social sustainability of pension systems in Central and Eastern European Countries. The econometric techniques in this study highlight those modern pensions systems that need to be addressed in a more complex and empirical context that must encompass the main technical aspects. The conclusions suggest that in the future it needs judicial, economic, and social adjustments for the enhancement of the financial soundness of the pension systems.

To get more data concerning the influence of fertilizers (organic and mineral) on different forage plants existing in North-eastern Romanian grassland, the mass fractions of 14 essential, enzymatic, or considerd toxic elements was determined by Instrumental Neutron Activation Analysis together with the amount of crude proteins, ash, fibres as well as ether fact extract. Final results showed a significant variance of the content of analysed elements on organic as well as on mineral fertilized experimental plots, i.e. the content increased in 24% of plots, decreased in 23%, and remained unchanged in 45% while in 8% of plots their content was below the detection limits, as the case of Se. At the same time, an increase content of crude protein and ether extract was evidenced in fertilized grasses for all applied fertilizers while other global indicators such as neutral and acid fibre of sufuric lignin content decreased, suggesting significant higher nutritional values of fertilized forage plant.

In the context of globalization One Health enables and concurs to the achievement of Global Health. One Health approach involves wide knowledge and understanding of its critical factors, next to an adequate implementation, also in farm animal sector. Moreover, animal farming and breeding shows particularities depending on country. Therefore, well-defined and specific strategies are still needed to be developed and adapted to the current conditions found in various countries for ensuring a well implementation, thus driving to better and healthier global outcomes and security. This paper will explore the One Health status in Romania, highlighting the current progress registered until now and the future perspectives based on its potential, in the context of the livestock farming framework and challenges. Our findings may help to disclose the challenges of putting in practice One Health in Romania, alongside to the pathways showing potential to enhance sustainability in livestock farming.

This paper presents a study of the 2D roughness profiles on a flat surface generated on a steel work piece, by ball nose end milling, with linear equidistant tool paths (pick-intervals). The milled surface exploration with a surface roughness tester (on pick and feed directions) produces usually 2D roughness profiles having periodical evolutions. These evolutions can be seen as time-dependent signals, describable as a sum of sinusoidal components (the wavelength of each component being regarded as a period). In order to detect a well approximated description of these components, two appropriate signal processing techniques are used in this work: first technique provides a direct mathematical (analytical) description and is based on computer aided curve (signal) fitting (more accurate), the second technique (providing an indirect and incomplete description) is based on the spectrum generated by fast Fourier transform (less accurate). This study can be seen as a way for a better understanding the interaction between the tool and the work piece or to achieve a mathematical description of the machined surface microgeometry in terms of roughness (e. g. its description being a collection of closely spaced 2D roughness profiles).

The purpose of the study is to show the effect of the intake of vitamin C obtained from a diet rich in fruit and vegetables or vitamin C supplements on the level of vitamin C in the plasma. The level of vitamin C in plasma were determined before the study (T1), and after five months (T2). Moreover, a medical record was carried out and a questionnaire on the habits such as general eating and specific consumption of food rich in vitamin C. Both of them were completed before and after five months. In addition, related anthropometric analyses were carried out. The results of the first determination of vitamin C level in plasma were between 1.0 and 16.0 mg/L and the results of the second determination of vitamin C in plasma were between 4.9 and 14.1 mg/L. Furthermore, it was identified that 50% of the questioned people had a low fruit intake. Raw vegetables were consumed by fewer people, the intake being higher during the main meals. The correlation of plasma vitamin C with the eating habits of the subjects to the study points out an interdependence between the consumption of fruit and vegetables and the level of vitamin C in the plasma.

Digital music is one of the most important things in market due to the music royalties’ distribution in Korea. As the music market is transformed to the digital music market such as download the music and streaming, the distribution of music royalties starting from online service provider (OSP) has come to be a highly important part for music rights holders. One of the most important issues in current music royalties’ distribution in Korea is the unfair way of music royalties due to indiscriminative repeat streaming of digital music. To prevent this, music log usage data from several OSPs was collected in day-based system, however, there was a limit to identify detailed information on the use of music in current state. This paper analyzed the structural problems and limitations of settlement of music royalties, and provides a structure in which there can be transparent settlement and distribution between users and rights holders as one of the institutional measures. We’ll also propose various AI-based applications using music log usage data. The proposed system will hopefully be used for public purposes.

Maritime transport has adapted to recent political and economic shifts by addressing stringent pollution reduction requirements, redrawing transport routes for safety, reducing onboard technical incidents, managing data security risks and transitioning to autonomous vessels. The integration of AI-based technologies for fault diagnosis and decision-making, coupled with proper personnel training, has become essential for optimal ship operation, with AI-assisted predictive maintenance emerging as the key strategy to ensure onboard systems function within desired parameters and enhance equipment availability. This study proposes a machine-learning algorithm for evaluating onboard systems performance by analyzing sensor data and mapping it to fault patterns to estimate functional states, validated through tests on a seawater cooling system from an oil tanker, demonstrating operational efficiency and reliability. The immediate advantage is reduced time for fault diagnosis by rapidly assessing the system using operational data, the algorithm enabling real-time monitoring and fault data management to minimize efforts as part of predictive maintenance assisted by machine learning tools.

Cellular senescence is a permanent condition of cell cycle arrest caused by a progressive shorten-ing of telomeres defined as replicative senescence. Stem cells may also undergo an accelerated se-nescence response, distinct from telomere shortening, known as premature senescence as a re-sponse to different stress agents. Various treatment protocols have been developed based on epi-genetic changes in cells throughout senescence, using different drugs and antioxidants, senolytic vaccines, or reprogramming of somatic senescent cells using Yamanaka factors. Even with all the recent advancements, it is still unknown how different epigenetic modifications interact with ge-netic profile and how other factors such as microbiota physiological conditions, psychological states and diet influence the interaction between genetic and epigenetic pathways. The aim of this review is to highlight the new epigenetic modifications that are involved in stem cell senescence. Here, we review recent senescence-related epigenetic alterations such as DNA methylation, chro-matin remodeling, histone modification, RNA modification, and non-coding RNA regulation outlining new possible targets for therapy of aging-related diseases. The advantages and disad-vantages of the animal models used in the study of cellular senescence are also briefly presented.

This study is focused on the mechanical properties of WC-Co composites obtained via Selective Laser Sintering using PA12 as a binder. The as-printed samples were thermally debonded, and sintered, first in vacuum, and then sinter-HIPed at 1400oC, using 50 bar Ar, which has led to relative densities up to 66 %. Optical metallographic images show a microstructure consisting of WC, with an average grain size in the range of 1.4 – 2.0 µm, with isolated large grains, in a well-distributed Co matrix. The shrinkage of the samples was 43 %, with no significant shape distortion. The printing direction of the samples has a great impact on the transversal rupture strength (TRS). Nevertheless, the bending strength was low, with a measured maximum of 612 MPa. SEM images of the fracture surface of TRS samples show the presence of defects that constitute the cause of the low measured values. The hardness values position the obtained composites in the range of medium coarse classical cemented carbides. The results were also related to the amount of free Co after sintering, close to the initial one, as assessed by magnetic measurements, indicating a low degree of interaction with PA12 decomposition products.

The paper highlights the performance of the seismic isolation devices, installed on retrofitted buildings in reducing the seismic response when subjected to earthquakes. Two buildings from the beginning of the XX-th century in Bucharest are chosen from many more, monitored over the city area. We discuss the response of these base-seismic isolated structures, relying on good quality data acquired from the recent strong earthquake (03.11.2022, MW = 5.0). Elastic response spectra computed from recordings at two levels of each structure are used, placed under and right above the isolating layer. At one building the existence of previous recordings and the particularity of the sensors allow a comparison with other two relatively recent medium intensity earthquakes. The assessment is carried out in terms of maximum acceleration amax, measured at certain levels in each structure, spectral acceleration amplitude SAmax and spectral-peak corresponding period. We find that the base-isolation methodology is effective in reducing the response of the building right above the isolating layer, an observation valid for both structures, all components of the recordings, and spectral acceleration values. Moreover, the outcomes from the modal evaluation performed prior to rehabilitation and seismic isolation process are presented, by pointing out a higher newly acquired fundamental period of the isolated structures.

The processing of cloud free geo-referenced imagery is one of the preliminary processing step of any land application. This letter describe the methodology developed to obtain a seamless cloud free composite of Africa for 2016 using Sentinel-2A data at 10 meters resolution freely available from the European Space Agency. The method is based on an hybrid method resulting from the merging of the two most robust time series methods namely the "darkest pixel" and the "maximum NDVI" previously developed with AVHRR time series.

Influence of Joule heating on magnetic properties, giant magnetoimpedance (GMI) effect and domain wall (DW) dynamics of Fe75B9Si12C4 glass-coated microwires was studied. A remarkable increase in GMI ratio is observed in Joule heated samples. The hysteresis loops of Joule heated samples maintain a rectangular shape, while a slight decrease in coercivity after Joule heating is observed. On the other hand, a modification of MOKE hysteresis loops is observed upon Joule heating. Additionally, DW dynamics improvement after Joule heating is observed. The observed GMI ratio improvement along with the change in MOKE loops and DW dynamics improvement has been discussed considering magnetic anisotropy induced by Oersted magnetic field in the surface layer during Joule heating and the internal stress relaxation. A remarkable GMI ratio im-provement observed in Fe-rich Joule-heated microwires with a rectangular hysteresis loop and fast DW propagation, together with the fact that Fe is a more common and less expensive metal than Co, makes them suitable for use in magnetic sensors.

The drug delivery systems receive more and more attention for the control and treatment of many diseases due to their increased number in recent years. The main aims of this study were to develop and to characterize a polyurethane drug delivery system that it is intended to be used for the transmembrane transport of nucleosides. Three different samples have been synthesized based on aliphatic diisocyanates (hexamethylene diisocyanate, isophorone diisocyanate and lysine diisocyanate) as organic phase, respectively a mixture of polyethylene glycol, polycaprolactone diol and low molecular weight diols as aqueous phase. The samples were characterized by pH, refractivity index and solubility measurements, drug loading efficacy and release investigations, thermal behavior, Zetasizer, cells viability and irritation tests on mice skin. The results indicate the obtaining of different populations of neutral acido-basic particles with size between 132 and 190 nm; the Zeta potential values and SEM images show a medium tendency to form clusters, while UV-Vis evaluations indicate an almost 70% encapsulation efficacy, a prolonged release (45% of encapsulated substance is released in the first 5 days) and around 70% of particles have penetrated an artificial membrane in the first 24h. The synthesized products can be tested in further clinical trials, the currently tests on cells culture and mice skin revealing no side effects.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

Cryosurgery has emerged as a promising method for harvesting veins, but the suitability of these cryostripped veins as grafts remains a subject of investigation. This study delves into uncharted territory by conducting an immunohistochemical analysis and exploring the molecular aspects of venous samples obtained through cryostripping. Existing literature lacks comprehensive data on the components of varicose veins' walls, particularly in relation to protein expression. Furthermore, little is known about the proliferation rate of endothelial cells within varicose veins, which we scrutinize alongside an assessment of CD34 endothelial reactivity. Materials and Methods: Our study encompassed 109 samples procured using the cryostripping method, which involves catheterizing veins with a specialized probe cooled to -85°C. Molecular profiling of the intima and endothelium was conducted using two key markers: CD34 and Ki67. Results: Immunoreactivity for CD34 was discernible across all three layers of the varicose vein walls that were excised using cryostripping. Notably, the endothelial cell layer exhibited intense and uniform positivity in 36 out of the 109 samples under investigation. In contrast, the results regarding Ki67 expression, whether pertaining to the intima or endothelium, remain inconclusive. Conclusions: Our findings advocate for the utilization of CD34 as a reliable marker to assess the morphological and molecular integrity of excised venous specimens. As the use of cryosurgery-harvested veins as grafts gains traction, this research contributes valuable insights into their potential viability for transplantation, opening new avenues for further exploration in the field of vascular surgery.

Background – Endobronchial squamous cell carcinoma is one of the most common types of tumors with such a location. Patients often present in advanced stages of the disease, which leads to a targeted therapeutic attitude of pneumonectomy, most of the time. Practicing a lung parenchyma-preserving surgery led us to do this review. Material and Methods - We used three search platforms SCIENCE, MEDLINE and PubMed, in order to identify studies presenting case reports, studies and reviews on endobronchial squamous cell carcinoma. We identified clinical and paraclinical features of endobronchial squamous cell carcinoma. All selected articles were in English and contained clinical criteria of endobronchial squamous cell carcinoma, autofluorescence bronchoscopy in endobronchial squamous cell carcinoma, imaging features of endobronchial squamous cell carcinoma, blood tumor markers specific for lung squamous cell carcinoma, histopathological features of endobronchial squamous cell carcinoma. Results - 73 articles were analyzed, from which 47 articles were selected as bibliographic references. We have presented the criteria found for endobronchial squamous cell carcinoma in order to highlight the main characteristics and high reliability technologies for the detection of this type of cancer. Conclusions – The current literature review highlights the clinical and paraclinical characteristics of endobronchial squamous cell carcinoma. It aims to open new horizons for research and early detection, frequent practice of lung parenchymal preservation surgery.

The prognosis of patients with recurrent or metastatic of the head and neck squamous-cell carcinoma (HNSCC) refractory to platinum-based chemotherapy is severe and, consequently, the identification of therapeutic options for this category of patients is a priority. Nivolumab, an anti- programmed cell death protein 1 (anti-PD-1) monoclonal antibody, has been approved for the treatment of recurrent or metastatic HNSCC after platinum-based therapy progressing. We present the early experience of two academic center including diagnostic, clinical, biological, therapeutic and outcomes characteristics of head and neck cancer (HNC) patients treated with Nivolumab. The purpose of the study is to identify certain peculiarities and to report them compared to the data from the literature in order to generate some hypotheses that coud constitute criteria for the selection of cases with maximum benefit to immunotherapy. Analyzing the data obtained from 18 patients treated in Emergency County Hospital Craiova, "Saint Nectarie" Oncological Hospital Craiova and Euroclinic Oncological Center Iasi January 2020 and March 2023 it could be hypothesized that lower nadir values of neutrophil to lymphocyte ratio (<3.5) and the adition of intensive regimens of chemotherapy and radiotherapy could justify a favorable response in terms of progression free survival (PFS) during immunotherapy with Nivolumab. To our knowledge, the study included the first two cases of second primary malignancy (SPM) in the head neck region treated with Nivolumab. The reported data support a possible benefit of the sequential administration of radiotherapy, immunotherapy for SPM cases. Higher positive dynamic of neutrophil to lymphocyt ratio (NLR) could be associated with worst outcome during immunotherapy. All study observations including the role of infections and antibiotic treatment as well as the possible biomarker value of NLR variation during immunotherapy should be investigated in multicenter clinical trials.

This paper aims to review the challenges, toxicity, and routes of synthesis and usage of silver nanoparticles in different applications but also highlighting their sustainability from both medical and environmental issues. Regarding their toxicity, it is known that silver nanoparticles can destroy over 650 microorganisms comparing with antibiotics. Supplementary, will be presented in a comparative manner some conventional synthesis routes (physical and chemical methods) and green synthesis routes using plant extracts. The approach using plant extracts have various advantages comparing with physical, chemical and microbial synthesis methods because there is no need to use chemicals, wasteful purifications and high energy requirements. The paper presents an overview on “green nanotechnology” focused on using either biological micro-organisms or plant extracts as an alternative to the classical chemical and physical methods. An important issue discussed in the paper is an overview of the synthesis routes of silver nanoparticles, some expected applications of silver based active agents and their toxicity and challenges that must be overcome. Also, it needs to focus our attention on the dismissal of silver nanoparticles into the environment and especially in water systems, fact which suggests that this issue must be fully understood and applied the law.

The paper aims to introduce user-friendly modelling approaches to analyze how abiotic factors influence various trophic levels within the marine ecosystem, both naturally and through human impact. It specifically investigates the connections between environmental parameters (like temperature, salinity, and nutrients) and plankton along the Romanian Black Sea coast during the warm season (May-September) over a decade. Utilizing machine learning (ML) algorithms and data collected during this period, models were developed to project the proliferation of zooplankton. During the warm season, water temperature emerged as a significant factor affecting copepods and “other groups” zooplankton densities, while no discernible impact was noted on Noctiluca scintillans blooms. Salinity fluctuations notably influenced typical phytoplankton proliferation, with phosphate concentrations primarily driving widespread blooms. Two scenarios were explored for forecasting zooplankton growth: Business as Usual, predicting modest increases in temperature, salinity, and constant nutrient levels, and the Mild scenario, anticipating more substantial temperature and salinity increases while nutrients decrease significantly by 2042. The findings highlight that under both scenarios, Noctiluca scintillans displays notably high densities, with the second scenario projecting even higher values, surpassing the first by around 70%. These densities indicate characteristics of a eutrophic ecosystem, suggesting the potential implications of altered abiotic factors on ecosystem health.

Introduction: The assumption that food resources and dietary supplements are natural and do not have side effects, or do not interact with drugs, is wrong, and can lead to unplanned symptoms or even hospital admissions. Also, not communicating with the family doctor, or the pharmacist, can make their work considerably more difficult in establishing the correct treatment. Methods: PubMed, ResearchGate, EUR-Lex, and Memorial Sloan Kettering Cancer Center databases for scientific literature were analyzed, for the keywords "adverse reactions", nutrivigilance", and "drug interaction". The method proposed by us for the implementation of nutrivigilance in the re-search-development stage is the application and adaptation of HACCP principles (Hazard Analysis and Critical Control Points) to nutrivigilance. Results: The implementation of nutrivigilance in the Romanian food supplements industry and healthcare system represent a real tool for improving public health management by preventing adverse reactions, and reducing the costs of the health system. From our knowledge, the proposal regarding the implementation of nutrivigilance in the research stage of food and food supplements, based on the principles of HACCP is unique. Conclusions: We believe that the proposed method is useful starting with the research-development of food supplements, followed by post-sale analysis.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

In this work, Al-Mo-B(CN) thin coatings were deposited by magnetron sputtering using composite metal-ceramic Al-Mo-B4C target. A metal-ceramic composite target for magnetron sputtering was fabricated by a robotic complex for detonation spraying of coatings equipped with a multi-chamber detonation accelerator. The powder composition (30Mo-30Al-40B4C) was sprayed onto the copper plate base of the composite target-cathode. The obtained cathode target with Al-Mo-B4C coating (thickness 280-300 μm) was used to deposit the Al-Mo-B(CN) coating (DC mode) on flat specimens of AISI 316 steels and silicon using equipment for magnetron sputtering UNICOAT 200. The Al-Mo-B4C coating has a lamella-type structure with inclusions of boron car-bide particles the elemental composition is evenly distributed in the material. The structure and morphology of coatings were studied using methods of optical, scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray analysis (XRD), and X-ray photoelectron spectros-copy (XPS). Mechanical and tribological properties of the Al-Mo-B(CN) thin coatings were determined using methods of nanoindentation, scratch testing, and tribological testing under fluid-free friction regime at room temperature. The Al-Mo-B(CN) coating (thickness ~ 1 μm) exhibited a dense uniform fine-grained structure with no columnar elements and were well-adherent to the substrates after deposition. Al-Mo-B(CN) coating has a amorphous structure. XPS analysis confirmed the formation of the MoB2 and AlN phase with an admixture of oxygen in the form of aluminum oxide, molybdenum oxide and boron oxide. Al-Mo-B(CN) coating possess hardness of 13 GPa, elasticity modulus of 114 GPa, elastic recovery of 45%, and friction coefficient of 0.8 against steel 100 Cr6 ball. The failure mode occurring in the tested coatings was fatigue and abrasive. The adhesion strength of Al-Mo-B(CN) coating amounted to about 11 N, and the failure mode was cohesive associated with plastic deformation and formation of fatigue cracks in the coating material.

The general desire of the world's population is to eat as healthily as possible, an aspect that has a direct impact on the technological complex aimed at animals raising (proper breeding systems, microclimate factors with implications for the welfare of animals, etc.), as well as on the quality of the finished products that will enter the food supply. Therefore, the authors set out to study how the growth system influences the health status of rainbow trout raised in different systems. The observed experimental factors did not undergo significant changes. However, differences were generated by the applied growth system. For the amount of glucose in the blood, no statistically significant differences were identified between the groups. In contrast, comparison of the amount of glycogen led to obtaining very distinctly significant statistical fluctuations (the mean for P-si was 2.314±0.638 and for P-i 1.980±0.822). Growth hormone varied between 0.504±0.46 in the case of P-si and 0.694±0.22 ng/ml for P-i. The values obtained for cortisol showed a significant influence of stress factors on the studied trout. The general conclusion of the present study is that various technological factors influence the health status of livestock.

Embryoid bodies (EBs) are multicellular three-dimensional (3D) aggregates generated from induced pluripotent stem cells (iPSCs) in suspension and serve as useful biological sources for many downstream applications. Imaging of live EBs has been hampered mainly due to the inherent limitations of the imaging techniques applied to date. This study aimed to image human iPSC (hiPSC) derived EBs to obtain their 3D volume, determining size, morphology, and cell viability from day 7 to 14 using Light Sheet Fluorescence Microscopy (LSFM). Furthermore, chromosomal stability was assessed using Multicolor fluorescence in situ hybridization (M-FISH) from day 8 to 14. EB volume increased from day 7 to 13 which, decreased at day 14. From day 7 to 11, the EBs mainly appeared spherical and morphed into an ellipsoidal shape by day 13. All EBs showed varied external morphologies and larger cavities at day 14. The EB karyotype was diploid 46XY at day 8 and exhibited a low level of aneuploidy from day 10 to 14. This study shows that an increase in cell death affects the morphology and chromosomal stability in EBs derived from hiPSC. We demonstrate that the combination of LSFM and M-FISH helps characterize EBs that will assist future stem cell therapies.

Low back pain is a common problem in the active population, and the second reason for visiting a physician. In patients with lumbar disc protrusion, the nucleus pulposus bulges against the disc and the latter protrudes into the spinal column, but the annulus fibrosus remains intact. The purpose of this study was to prove that starting an early complex rehabilitation treatment results into pain and disability reduction, and increased muscle strength and mobility in patients with lumbar disc protrusions. We performed a prospective cohort study, enrolling 60 patients (25 men and 35 women) aged between 26 to 76 years, diagnosed with lumbar disc protrusion. Patients in the experimental group registered significant improvements in all studied variables (pain, mobility, muscle strength, disability) after 6 months of treatment. The results of our study suggest that, in the lumbar disc disease, a combined rehabilitation program may be more effective in terms of pain and disability reduction, if it starts early after diagnosis. The current study proves the importance of combining electrotherapy with hydrotherapy and physical therapy. Patients who received this treatment combination showed an extremely significant improvement in pain relief, and reduction of functional disability after 6 months of treatment.

Micro and small wood-processing enterprises represent the heart of the European forest-based industries, being among the key drivers of economic growth in rural, mountainous, and poor regions. Their economic efficiency is of fundamental importance for their existence and the pro-vision of income for the local population in rural areas. Data Envelopment Analysis (DEA) is nonparametric, linear-programming-based approach, commonly used to analyse the efficiency of organizational units. This method allows estimating the economic efficiency of a certain eco-nomic system without assumptions about the functional form between resources and products. Furthermore, DEA determines the efficiency frontier and gives results of whether an enterprise, i.e., a Decision Making Unit (DMU) is efficient or not. The main objective of this study was to investigate and evaluate the economic efficiency of micro and small wood-processing enterpris-es in the EU countries and reveal the hidden inputs that facilitate efficiency generation. The eco-nomic efficiency evaluation was carried out on the basis of the official statistical data for the mi-cro and small wood-processing companies in the EU member states for the period 2015-2020 by performing a two-stage DEA analysis. The data used were standardized by value per employee. In addition to the first stage of DEA, fractional regression probit and logit models with four contextual variables were used to reveal the influence of the hidden inputs in the model. The results showed that the micro and small wood-processing enterprises can be regarded as more scale-efficient than technically-efficient entities. The only contextual variable affecting the eco-nomic efficiency was Investments per Person Employed, improving the efficiency by 2% per 1% increase of the investments.

This paper presents the values of several mechanical characteristics for two blends: H (60% PP + 12% PA6 + 8% EPDM + 20% Polybond 3200) and G (20% PP + 42% PA6 + 28% EPDM + 10% Polybond 3200) (%wt), comparing them to those of PP (polypropylene) and PA6 (polyamide 6). The adding of EPDM (ethylene propylene diene monomer rubber) and Polybond 3200 help reducing the disadvantages of simple blends made of PP+PA6, when the PA6 concentration allows for having a PA6 matrix with droplets of PP. SEM analysis helps for understanding the performance of material G as compared to the neat polymers. EDX analysis proved that there was a matrix inversion, material H having a PP matrix and material G a matrix made of PA6 with droplets of PP. Strain at break for PP and material H were proved to be insensitive to test speed, but materials G and PA6 had large value for strain at break and energy at break for v = 10 mm/min. Taking at basis the values for polyamide 6 (PA6), material G has greater values for energy at break: with 97.8% for v = 10 mm/min, with 29.5% for v= 250 mm/min and with 98% for 1000 mm/min, without exhibiting the micro and macro cavitation of PA6. This means that the recipe, the technology and the mechanical characteristics make material G a potential candidate for applications where a low and moderate impact resistant material is required.

We present set-theoretical solutions of the Yang-Baxter equation in BCK–algebras. Some solutions in BCK−algebras are not solutions in other structures (such as MV −algebras). Related to our investigations we also consider some new structures: Boolean coalgebras and a unified braid condition – quantum Yang-Baxter equation. Finally, we will see how poetry has accompanied the development / history of the Yang–Baxter equation.

Critically ill patients with sepsis require a multidisciplinary approach, as this situation implies multiorgan distress, with most of the bodily biochemical and cellular systems being affected by the condition. Moreover, sepsis is characterized by a multitude of biochemical interactions and by dynamic changes of the immune system. At the moment, there is a gap in our understanding of the cellular, genetic, and molecular mechanisms involved in sepsis. One of the systems intensely studied in recent years is the endocannabinoid signaling pathway, as light was shed over a series of important interactions of cannabinoid receptors with biochemical pathways, specifically for sepsis. Furthermore, a series of important implications on inflammation and the immune system that are induced by the activity of cannabinoid receptors stimulated by the delta-9-tetrahidrocannabinol and cannabinol have been noticed. The aim of this review paper was to present, in detail, the important mechanisms modulated by the endocannabinoid signaling pathway, as well as of the molecular and cellular links it has with sepsis. At the same time, we wish to present the possible implications of cannabinoids in the most important biological pathways involved in sepsis, such as inflammation, redox activity, immune system, and epigenetic expression.

Background and Objectives: Romania ranks among the countries with a notably high rate of preventable deaths due to inadequacies in prevention, screening, early detection, and timely management processes. Cervical cancer (CC) is a significant contributor to these preventable deaths, particularly affecting patients from marginalized backgrounds, rural regions, and the Roma population. The purpose of this article was to identify correct and consistent information of the Roma population about the risk of CC, as well as the importance of understanding the causes of the disease and awareness of the available prevention methods. Materials and methods: A cross-sectional study was conducted using a self-administered questionnaire applied only to Roma women in Romania. Results: We enrolled 759 patients in the study. These were divided into 2 groups, Group 1 comprised 289 (38.1%) women who had been tested for HPV infection, while Group 2 included 470 (61.9%) women who had never been tested for HPV infection. Characterization of women in Group 1: mostly aged between 25-54 years, with high school education, married, who started sexual activity under the age of 18 years, with only one sexual partner and with over 5 pregnancies. Regarding contraceptive methods, 35.7% of women do not know/ use any contraceptive method, and 32.2% use hormonal contraceptives. Two thirds of the women tested had heard of HPV, and 19.7% were vaccinated against HPV with at least 2-3 doses. A percentage of 8.7 had a diagnosis of CC, compared to those who were not tested (p-0.0001), whereas 63% of the tested women do not know much about CC, as opposed to 85.7% of the group of untested women. Conclusion: Cervical cancer (CC) continues to be a public health issue in Romania, particularly in patients belonging to vulnerable groups. Promotion campaigns for HPV vaccination and CC screening are necessary to reduce the associated mortality and morbidity.

Abstract: (1) Background: The relationship between non-alcoholic fatty liver disease (NAFLD) and type 2 diabetes (T2DM) is bidirectional: NAFLD increases the risk of T2DM, and T2DM promotes the progression of the disease to non-alcoholic steatohepatitis (NASH). (2) Material and methods: We performed a retrospective, open study that included 59 patients with NAFLD and T2DM who were distributed into two groups: 44 (74.57%) patients were diagnosed with HS and 15 (25.42%) patients were diagnosed with NASH. (3) Results: Among the non-specific inflammatory biomarkers statistically significant (p=0.003 respectively p=0.03) higher mean values were recorded in patients with NASH and T2DM in the case of ferritin and the neutrophil percentage-to-albumin ratio (NPAR). (4) Conclusions: Consequently, it is essential to identify alternative "surrogate" markers for the inflammatory process, particularly in individuals with diabetes, as it is a key characteristic of NASH. This need arises from the desire to avoid the risks associated with liver biopsy procedures and to prevent the unpredictable and unfavorable progression of NAFLD in patients with T2DM.

Orbital fractures are a common finding in facial trauma and serious complications may arise when orbital reconstruction is not done properly. The virtual planning can be used to manufacture patient-specific titanium orbital implants (PSI) through the process of selective laser melting. This method is currently considered the most accurate technique for orbital reconstruction. Even with the most accurate tehniques of bone reconstruction, there are still situations where enophthalmos is present after reconstruction which may be produced by intraorbital soft tissue atrophy. The aim of this paper was to evaluate the orbital soft tissue after postraumatic reconstruction of the orbital walls fractures. 10 patients diagnosed with unilateral orbital fractures were included in this study. A CT scan of the head region with thin slices (0.6mm) and soft and bone tissue windows was done. After data processing, the STL files were exported and the intraorbital fat tissue volume and the muscular tissue volume were masured. The volumes of affected orbit tissues were compared with the volumes of the healthy orbit tissues for each patient. Our findings conclude that a higher or a lower grade of fat and muscular tissue loss is present in all cases of reconstructed orbital fractures.

Although a slightly radioactive element, thorium is considered very toxic because its various species, which reach the environment, can constitute an important problem for the health of the population. The present paper aims to expand the possibilities of using membrane processes in the removal, recovery and recycling of thorium from industrial residues reaching the municipal waste processing platforms. The paper includes a short introduction on the interest shown for this element, a weak radioactive metal, followed by highlighting of some common (domestic) uses. In a distinct but concise part, the bio-medical impact of thorium is presented. The classic technologies for obtaining thorium are concentrated in a single schema, and then the speciation of thorium is presented with an emphasis on the formation of hydroxo-complexes and complexes with common organic reagents. The determination of thorium has been highlighted both on the basis of its radioactivity, but especially through methods that call for extraction followed by an established electrochemical, spectral or chromatographic method. Membrane processes are presented based on the electrochemical potential difference, rapidly presenting barro-membrane processes, electrodialysis, liquid membranes and hybrid processes. A separate sub-chapter is devoted to proposals and recommendations for the use of membranes in order to achieve some progress in urban mining for the valorization of thorium.

We present the case of a 35-year-old patient without pathological history who developed hemopneumothorax due to altitude barotrauma during a commercial airline flight. The computed tomography of the chest identified the presence of emphysema "blebs" and bubbles, and the histopathological examination of the lung fragment obtained during the diagnostic and therapeutic thoracoscopy identified elements suggestive for the diagnosis of respiratory bronchiolitis associated with desquamative interstitial pneumonia (DIP).

The article presents the results of the technical-economical study regarding the optimization of the FDM parameters (Lh – the height of the layer deposited in one pass and Id – the filling percentage) for the manufacture of PETG and ASA parts. To carry out the technical-economical study, we used the fundamental principle of value analysis, which consists in maximizing the ratio between Vi/Cp, where Vi - represents the mechanical characteristic, and Cp - represents the production cost. The results of the study show that for the tensile specimens made of PETG, the parameter that significantly influences the results of the Vi/Cp ratios is Lh, and in the case of the compression specimens made of PETG, the parameter that significantly influences the results of the Vi/Cp ratios is Id. In the case of specimens manufactured by FDM from ASA, the parameter that decisively influences the results of the Vi/Cp ratios of the tensile and compression specimens is Id – the filling percentage. By performing optimization of the process parameters with multiple responses, we identified the optimal parameters for FDM manufacturing of parts from PETG and ASA: Lh = 0.20 mm and Id = 100%.

We studied the magnetostriction coefficients, λs, Curie temperature, Tc, and their dependence on annealing conditions in Fe47Ni27Si11B13C2 and Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 amorphous glass-coated microwires with rather different character of hysteresis loops. A positive λs≈20x10-6is observed in as-prepared Fe47Ni27Si11B13C2, while low and negative λs ≈-0.3x10-6 is ob-tained for Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 microwire. Annealing affects the magnetostriction coeffi-cients and Curie temperatures, Tc, of both Fe47Ni27Si11B13C2 and Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 glass-coated microwires in a similar way. Observed dependencies of hysteresis loops, λs and Tc on annealing conditions are discussed in terms of superposition of internal stresses relaxation and structural relaxation of studied microwires. We observed linear λs dependence on applied stress, σ, in both studied microwires. A decrease with applied stress is observed for Co-rich mi-crowires with negative magnetostriction coefficient. In contrast, a linear increase of the magne-tostriction coefficient with applied stress is observed for Fe-Ni- rich microwires with positive magnetostriction coefficient. Observed results are discussed in terms of influence of internal stresses and short range atomic rearrangements induced by annealing on hysteresis loops, magnetostriction coefficients and Curie temperatures of studied microwires.

As well known, the torque produced by a rotating motor generates an opposite and equal reaction torque in the machine casing that must be transmitted to the base. In many applications, especially when the reaction moment has high values, it is necessary to apply some constructive solutions, which in certain cases are difficult to implement. In this context, the need to reduce the reaction moment from drive motors is a challenging topic, which has not been completely exhausted. In this paper, the authors present an original concept of a device which uses the centrifugal force generated by some equidistantly placed weights on a chain drive, for reducing the reaction torque of the motor used for driving a rotating tool. The proposed system is capable to produce a supplementary torque which can be added to driving moment. Due to this fact, by using this system, the power of the driving motor can be decreased, with the consequence of reducing the reaction moment, that must be absorbed by the base.

Groove pancreatitis represents a chronic focal form of pancreatitis affecting the zone between the pancreatic head and the duodenal „C” loop, known as the groove area. This is a rare condition that affects the pancreatic periampullary part, including the duodenum and the common bile duct, associated usually with long-term alcohol and tobacco misuse and being more frequent in men than in women. The most common clinical symptoms of groove pancreatitis include weight loss, acute abdominal pain, nausea, and jaundice. This report is about a 66 year old woman with a history of heavy smoking, presenting with weight loss, nausea, and upper abdominal pain. Contrast enhanced computed tomography revealed the existence of a chronic pancreatitis as well as the dilatation of the main pancreatic duct, a cyst of the pancreatic head and enlargement of the biliary tract. Conservatory treatment was initiated but with no improvement of symptoms. Since there was no indication for endoscopic retrograde cholangiopancreatography, we decided to perform a pancreatoduodenectomy, as surgery appears to be the single effective treatment.

Dirofilariosis is an infectious disease caused by species of the Dirofilaria genus. It is manifested by the appearance of a subcutaneous swelling, especially in the eye region. We present the case of a 29-year-old patient that accused facial asymmetry in the right genian region. Following clinical and paraclinical evaluations, the diagnosis of parasitic cyst was established in the context of dirofilariosis with Dirofilaria repens (D. repens). Treatment consisted of surgical excision of the formation associated with prophylactic antibiotic medication. Macroscopic analysis of the excision piece revealed a structure that contains a cystic cavity and a filamentous form with a length of approximately 10 mM and a diameter of 1 mM. This is the first case of dirofilariosis located in the genian region reported in Romania. The overview of this pathology is important to raise awareness among physicians about its presence and its clinical variations.

Considering the worldwide impact of heart failure, it is crucial to develop approaches that can help us comprehend its root cause and make accurate predictions about its outcome. This is essential for lowering the suffering and death rates connected with this widespread illness. Cardiomyopathies frequently result from genetic factors, and the study of heart failure genetics is advancing quickly. Dilated cardiomyopathy (DCM) is the most prevalent kind of cardiomyopathy, encompassing both hereditary and nongenetic abnormalities. It is distinguished by the enlargement of the left ventricle or both ventricles, accompanied by reduced contractility. The discovery of the molecular origins and subsequent awareness of the molecular mechanism is broadening our knowledge of DCM development. Additionally, it emphasizes the complicated nature of DCM and the necessity to formulate several different strategies to address the diverse underlying factors contributing to this disease. Genetic variations that can be transmitted from one generation to another can be a significant contributor to causing family or isolated DCM. Genetic variation also plays a significant role in determining susceptibility for acquired triggers for DCM. The genetic causes of DCM can have a diverse range of phenotypic expressions. It is crucial to select the most probable patients to have advantages from genetic testing. The purpose of this research is to emphasize the significance of identifying genetic DCM, the crucial relationships between genotype and phenotype, and the usefulness of genetic testing in the therapeutic care of both those affected and their relatives. This approach is expected to gain importance once treatment is guided by genotype-specific advice and disease-modifying medications.

Cobalt ferrite nanoparticles (NPs) doped with rare earth (RE) metals with general formula CoFe_2-xRE_xO₄ (RE=Yb, Dy, Gd; x = 0.0 - 0.3) were synthesized by the co-precipitation method followed by post thermal treatment. The influence of RE doping on structural, magnetic and thermal properties and potential biomedical applications like magnetic hyperthermia has been investigated. In the as-prepared samples RE cations enter the spinel lattice as detected by X-ray diffraction. Thermal treatment leads to thermodynamically stable and relaxed single-phase spinel structures only for lower RE content, x = 0.01-0.05. However, annealed samples present higher mass magnetization values (M_S), up to 83 Am²/kg. RE content also affects M_S, especially in the case of annealed samples where it decreases linearly with x from about 80 Am²/kg (x = 0.01) to about 60 Am²/kg (x = 0.30). Thermal treatment induces a reduction in coercivity from 60-100 mT for as-prepared samples to 18-33 mT for annealed samples, in a nonlinear manner with respect to RE content. Heating efficiency, i.e., Specific Loss Power (SLP), of all samples has been studied using both magnetometric and calorimetric method to deeper examine the energy loss mechanisms involved.

This study examines the effectiveness of a comprehensive psychomotor development program combined with adapted football training for adolescents diagnosed with intellectual disabilities in Romania. Twelve participants, with a mean age of 17.42 years underwent a carefully designed intervention program spanning 36 weeks. The program aimed to enhance fundamental movement skills, integrate these skills into specialized football training, and culminate in a Unified 7-a-side Football Match. Results indicate significant improvements in psychomotor skills, including static and dynamic balance, pulse processing speed, and identified stimuli. Moreover, the intervention positively impacted social interaction among participants. Statistical analysis, employing Pearson Correlation Analysis and Paired Samples t-Test (One-Sample), compared assessments. Results revealed significant differences between pre- and post-intervention measurements, providing robust evidence of the program's efficacy. The positive correlations between physical parameters and social interaction highlight the interconnectedness between physical fitness and social engagement. Our findings suggest that improvements in physical abilities may contribute to increased social interaction among children with intellectual disabilities, underscoring the holistic nature of our intervention, which addresses multiple dimensions of development simultaneously. The findings underscore the holistic benefits of integrating psychomotor development and adapted football programs for adolescents with intellectual disabilities, emphasizing the importance of promoting inclusive physical activities for their overall well-being.

This paper experimentally reveals some of the resources offered by the evolution of the instantaneous active electric power in describing the state of three-phase AC induction asynchronous electric motors (with squirrel-cage rotor) operating under no-load conditions. A mechanical power is required to rotate the rotor at no-load and this mechanical power is satisfactorily reflected in the constant and variable part of instantaneous active electric power. The variable part of this electrical power should necessarily have a periodic component with the same period as the period of rotation of the rotor. The paper proposes a procedure for extracting this periodic component description (as a pattern, by means of a selective averaging of instantaneous active electrical power) and analysis. The time origin of this pattern is defined by the time of a selected first passage through the origin of an angular marker placed on the rotor, detectable by a proximity sensor (e.g. a laser sensor). The usefulness of the pattern in describing the state of the motor rotor has been demonstrated by several simple experiments which show that a slight change in the no-load running conditions of the motor (e.g. by placing a dynamically unbalanced mass on the rotor) has clear effects in changing the shape of the pattern.

The paper combines two new original concepts about eco-energetic systems. The first one is related to the M.E.N. (Mega-Eco-Nega-Watt) paradigm, which is based on three different but complementary ecological economic spaces: MEGAWATT, as needed energy, ECOWATT, as ecological energy, and NEGAWATT, as preserved energy, even the renewable energies and technologies, in the context of electrical energy production. The second concept presented in this paper is the eco-energetic efficiency, introduced in order to facilitate a correlation between the energetic efficiency of the system and a necessary, new defined ecological coefficient. The proposed formula for eco-energetic efficiency enables an interesting form of reporting to the different situations in which the input energy, output energy, lost energy and externalities, involved in an energetic process interact to produce energy in a specific energetic system, in connection with the circular economy model. Finally, is presented an original diagram of the energetic chains to produce electricity in a resilience regim, with high eco-energetic efficiency from originating in different primary energetic sources as external (gravitation & solar sources), fuels (classical & radioactive), internal sources and others. Even what kind of energetic sources are used to obtain electricity, as coals, gas, wood, hydropower, nuclear power, wind power, biomass, solar systems, and others, the entire process should be sustainable in what is the transdisciplinary integration of the different representative spheres as energy, socio-economy, ecology (environment), with the main core, sustainable education, inclueding the law and administrative aspects, as necessary fields of the knowledge based society/economy.

The influence of post-processing conditions on the magnetic properties of amorphous and nanocrystalline microwires have been thoroughly analyzed, paying attention on the influence of magnetoelastic, induced and magnetocrystalline anisotropies on the hysteresis loops of Fe-, Ni- and Co-rich microwires. We showed that magnetic properties of glass-coated microwires can be tuned by the selection of appropriate chemical composition and geometry in as-prepared state or further considerably modified by appropriate post-processing, which consists of either annealing or glass-coated removal. Furthermore, stress-annealing or Joule heating can further effectively modify the magnetic properties of amorphous magnetic microwires owing to induced magnetic anisotropy. Devitrification of microwires can be useful for either magnetic softening or magnetic hardening of the microwires. Depending on the chemical composition of the metallic nucleus and on structural features (grain size, precipitating phases) nanocrystalline microwires can exhibit either soft magnetic properties or semi-hard magnetic properties. We demonstrated that the microwires with coercivities from 1 A/m to 40 kA/m can be prepared.

Within an amplicon-based metagenomic study of Archaea, Fungi, and Bacteria in Livingston Island, Maritime Antarctica, in many of the samples antagonisms between these three super kingdoms were observed under the form of an inversely proportional dependence of the richnesses of the three types of microorganisms. This was quantified - based on the observed numbers of the total tags and the numbers of the operational taxonomic units (OTUs), as well as based on four alpha diversity parameters – the Shannon, the Simpson, the Chao1, and the ACE indices. We found that the most discriminative results in the antagonism measuring were observed in the comparison of the numbers of the OTUs and the ACE community richness estimator. The antagonism between Archaea and Fungi was strongest, followed by that of Archaea and Bacteria. The Fungi-Bacteria antagonism was slightly detectable. Pearson and Spearman correlation analysis also showed a statistically significant negative correlation between the fungal and archaeal effective tags, while the correlation between archaeal and bacterial diversity was positive. Indications of the order of primary microbial succession in barren ecological niches were also observed, demonstrating that Archaea and Bacteria are the pioneers, followed by Fungi which in time would displace Archaea.

Keywords: Trichoderma sp., biogenic selenium nanoparticles, capping biomolecules, bio-corona, agriculture, plant biostimulants, phytopathogens, physicochemical properties, bioactivity mechanism

Life Cycle Cost Analysis is a method used to assess long-term economic efficiency among equivalent competing processes or products. The purpose of the paper is to investigate the nature and level of costs for an organic orchard located in Southern Romania, using a complex approach covering the entire chain of production, through the life span. The research results, based on a dynamic analysis and an integrated evaluation of the orchard's performance, have been ranked on investment and operational costs, broken down on three categories (establishment and production, post-harvest and transport costs). The highest cost, representing 151726 euros/ha/20 years, about 52.72% of the total operational costs and 50.4% of the total farm costs/ha/20 years, was recorded in exploitation stage. The scenarios for the sensitivity analysis considered different levels of average yield (40, and, respectively 60 tons/ha) with different rate of sold production (85%, optimistic scenario; 70%, pessimistic scenario). The hotpoints identified at the production stage were use of agricultural machinery, several pesticides, the costs of seedlings, anti-hail net, plastic boxes and labor cost, while at the post-harvest stage, were those related to labor and energy consumption. The transport stage has had important costs with tractor operation and the track.

This scientific paper explores the increasingly widespread use of collaborative robots in the industrial environment, highlighting them as a solution to challenges related to the high costs of human labour and the associated management difficulties. The authors focus on the process of defining requirements for the implementation of collaborative robots, providing strategies based on mathematical management models. This approach translates into significant benefits for companies, such as cost reduction, quality improvement, and increased operational efficiency. Additionally, the paper proposes an innovative mathematical model for assessing total costs, budgeting, profitability, and electric power consumption associated with the operation of collaborative robots. This model allows for a comparison between the costs involved in using human labour and those associated with collaborative robots, providing critical information for technological investment decisions. The efficiency of this mathematical model is demonstrated through a practical application, where collaborative robots were integrated into a production environment, and costs and efficiency were evaluated compared to the use of human labour. This scientific paper provides a systematic and efficient approach to implementing collaborative robots in industrial processes, benefiting from strategies based on mathematical management models and an original mathematical model for evaluating performance and associated costs.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.