A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

The aim of this investigation is to offer a data-based scheme for predicting electrode wear in resistance spot welding. Electrode wear and alloying is one of the most significant factors that affect the mechanical properties of spot welds and the variation in weld quality. In this study, Rogowski coils and twisted pairs attached to the top and bottom electrodes were used to obtain the welding current and the inter-electrode voltage in the welding process, thereby calculating the dynamic resistance value during the welding process. The electrode diameter was obtained from the pressure exerted by the upper and lower electrodes on the carbon paper when the current was cut off and was regarded as an indicator of electrode wear. By continuously welding 0.5mm thick BH 340 steel plates until the electrode failed, the dynamic resistance signal was recorded in real time. Simultaneously, the electrode diameter after every 4 welds was also recorded. On this basis, the correlation between electrode diameter and dynamic resistance is studied. In order to quantitatively study the mapping relationship between dynamic resistance and electrode wear, 11 characteristic values were extracted from the dynamic resistance, and the stepwise regression method was used to obtain the regression formula between the characteristic values and the electrode diameter. Using new data to verify the effectiveness of the regression model, the acquired results display that the maximum error between the predicted value of the electrode diameter and the measured value obtained by the regression equation with the interactive quadratic term is 0.3 mm, and the corresponding relative error is 7.69 %. This result demonstrates that the method proposed in this paper can effectively monitor the electrode wear and failure process.

According to traditional Chinese medicine, Qi and Blood circulate through the human body via pathways known as 'channels and collaterals'. This process supports the normal function of internal organs and the whole body. Pathological conditions can be attributed to abnormal circulation of Qi and Blood, which results in excess or deficiency of organs and channels. Therapeutic methods used in traditional Chinese medicine restore the balance of Qi and Blood.Since acupuncture was introduced in Europe, discussion and debate about the nature of 'acupoints,' 'channels,' and 'collaterals' has continued. Currently, opposing views exist on this subject, ranging from complete denial of the existence of the channels to uncovering the previously unknown system of intra-tissue gaps and microscopic vessels. The author offers an original hypothesis that regards the theory of channels and collaterals as the description of the physiology and pathology of intercellular space and the theory of organs as a description of the physiology and pathology of cells.

Background: An analysis of the pages of the WHO website on the influenza pandemic revealed changes in the use of the term "pandemic" that occurred in 2009 and 2011. Materials and methods: Since the cause of the change in the description of a pandemic on the WHO website in 2009 and 2011 is not clear, analyses of the literature related to the epidemics and pandemics, WHO documents, WHO website, and articles published in journals and the Internet have been done.Results: Until early May 2009, the description of the pandemic focused on "enormous numbers of cases and deaths." On May 6, 2009, a new description of the pandemic was published, focusing on the prevalence of the disease, but in 2011 it reverted to the initial one without any comments. From the perspective of the WHO document issued in 2009, the declaration of a swine flu pandemic in June 2009 seemed justified. However, considering the previous pandemic history, common sense, and the consequences of declaring a pandemic for a disease not accompanied by a high number of cases and high mortality, it was a premature move.Conclusion: Since the primary factor hindering the development of a pandemic is the effectiveness of treating infectious diseases, but not a definition of a pandemic, to minimize the likelihood of a new pandemic, it is necessary to improve the quality of special medical education and to study and adapt to modern conditions all effective drugs and methods used in the past.

For several millennia, doctors and healers used therapeutic ingredients extracted from minerals, plants, and animals. Among the active remedies derived from animals, the placenta was among the most popular ones. The use of placenta-based remedies has retained its significance in our time. The placenta-based therapeutics are indicated for stimulating immunity, wound healing, reduction of skin pigmentation, treatment of various patients suffering from gynecological disorders, etc. By the beginning of the 21st century, the majority of specific functions and chemical ingredients of the placenta were identified and described. However, only now active proteins and peptides with molecular weight of about ten kDa were revealed. Presumably, they play an essential role during the therapeutic application of placental extract. Hopefully, this discovery will start a new era in the research and clinical application of organotherapeutic remedies, including placenta.

Background: Since the previous study dealing with the case fatality ratio and infection fatality ratio caused by COVID-19, the author has received many comments that prompted the question: "Why did an optimistic prognosis fail?" To answer this question, a more detailed and expanded analysis was carried out in a new study. Objective: To evaluate the dynamics of monthly numbers of cases, deaths, tests and CFR worldwide during three phases of the COVID-19 pandemic. Material and Methods: Twenty three sets of databases, dated the 22nd of each month from January 2020 to November 2021, for 213 countries were collected from the Worldometer website. The number of cases, deaths, tests, CFR, IFR, etc. were counted for various periods of time for each of the 213 countries, then results related to different periods of time were compared. Results: The analysis of the main epidemiological parameters led to the division of three phases of the global pandemic evolution. The first phase (23.01.20-22.07.20), the second phase (23.07.20-22.01.21) and the third phase (23.01.21-22.07.21) were different in terms of the number of tests performed, new cases, and mortality due to COVID-19. By the end of the second phase, the worldwide statistics indicated the imminent end of the pandemic, but the third phase was characterized by a sudden rise in the number of new cases and deaths that could not be explained rationally. The most dramatic evolution of the epidemic curve occurred in the countries where doctors had successfully battled COVID-19 during the first two phases of the pandemic. Conclusions: Despite the decrease in overall death numbers during the latest months analyzed, additional study is necessary to identify the cause for the increase in the number of new cases and deaths during the third phase of the pandemic. Only complete information regarding the positive and negative impact of medical and non-medical methods of diagnostics and prophylaxis of COVID-19 can help to organize effective measures to end the current pandemic and prevent a similar one from occurring in the future. Presumably, there are several causes of the negative evolution of the current pandemic, including the overreliance on PCR tests, application of non-specialized premises for quarantine and treatment, decrease in herd and individual immunity, inadequate change of therapeutic protocols, and ignoring prophylactic treatment. It can be suggested that the use of immunemodulatory drugs, for example, thymus extract or thymic peptides, in groups of people with compromised immunity is necessary, and prophylactic and therapeutic protocols should be changed from the 'standard' types to 'personalized' ones.

Background. The Weekly Mortality Cycle among CoViD-19 patients has been studied.Methods. Mortality data obtained from the 'Worldometer' website were analyzed with a comparison of absolute values, percentages, and p-value. Results. For patients suffering from CoViD-19, the most favorable or the safest days of the week were Sundays and Mondays. Conclusion. The weekly cycle with decreased mortality on Sundays and Mondays is a unique phenomenon observed among victims of CoViD-19. Presumably the decreased mortality on certain days of the week related to the optimized therapeutic protocols used on the "safest days".

Regular regimes of oil and oil products pipelines are studied. The problem is to develop an algorithm of effective pipeline system control that ensures the fulfillment of specified boundary conditions at the system boundaries. The product is pumped in batches, the flow is characterized by a change in temperature and pressure flow parameters over time. The developed solution method uses the principle of decomposition in the sense that each computational iteration is im-plemented in 3 stages, in three nested loops. The inner cycle is connected with the material bal-ance relations, at the next cycle the flow equations are introduced and the fulfillment of the 2nd Kirchhoff's law is monitored. If the flow process is significantly affected by temperature, then an external cycle is also implemented, correcting the solution so that the energy conservation equa-tion is satisfied. In the calculation procedure, some computational difficulties may arise, which consist in choosing an appropriate optimization method. On a specific example, the possibility of using various library programs to solve the problem was checked. The developed method is suita-ble for the analysis of systems of arbitrary topology. Since the method is not time-consuming, it can be recommended for online control of oil and oil products supply systems. The paper opens a new direction in the theory of hydraulic circuits. It uses both traditional methods of continuum mechanics and stochastic models.

This article proposes the multilayer and multilevel cosmological model, on average, balanced with respect to the Einsteinian vacuum. This hierarchical model is based on 10 possible Kottler solutions of the extended Einstein's field equations. The extension of the Einstein field equations is associated with the addition of an infinite number of lambda_j-terms to these equations with the condition that the series (i.e., the total sum) of these terms converges to zero. A simplified ten-layer and ten-level case is considered, in which ten spherical formations are sequentially nested into each other like "nesting dolls", while the radii of these spherical formations correspond to the characteristic sizes of a discrete sequence of observed spherical objects: metagalaxy core, galactic cores, stellar (planet) core, biological cells and nuclei of atoms and elementary particles, etc. As an example, from the general ten-level (hierarchical) solution of extended Einstein's field equations, two antipodal spherical formations with a core radius commensurate with the classical electron radius are singled out. Therefore, the metric-dynamic models of these formations obtained in this way are called «electron» and «positron». The article is aimed at the development of differential geometry and the program for the complete geometrization of physics by Clifford-Einstein-Wheeler.

This study comprehensively evaluates the DNA/RNA Defend Pro (DRDP) sample collection buffer designed to inactivate and stabilize patient samples. The primary objectives encompassed assessing DRDP's efficacy in ensuring sample stability, facilitating extraction-free polymerase chain reaction (PCR), and ensuring compatibility with rapid antigen testing.Ninety-five diagnostic nasopharyngeal swab samples tested for influenza A/B, RSV A/B, and/or SARS-CoV-2 were diluted 1/10 with DRDP and anonymized. Stability testing involved incubating 31 positive samples at 4 °C, 20 °C, and 37 °C for 7 days, with regular extraction-free nucleic acid amplification testing (NAAT).Results demonstrated that DRDP guaranteed viral RNA stability at all temperatures for influenza, SARS-CoV-2 and RSV showing stability up to 7 days at 4 °C. DRDP-diluted samples exhibited robust compatibility with direct PCR, as 72 out of 88 samples positive for cobas Liat also tested positive for direct PCR. Non-concordant results could be explained by the 200-fold lower input in the extraction-free NAAT.Compared to NAAT, rapid antigen testing demonstrated lower sensitivity, as expected, while maintaining perfect specificity. Clear cutoffs between positive and negative rapid antigen testing results were observed in both cobas Liat and direct PCR analyses, validating DRDP's compatibility with these techniques. In conclusion, DRDP is an effective stabilizing medium compatible with direct PCR and rapid antigen testing and shows great potential for optimizing diagnostic processes, particularly in resource-limited or time-sensitive scenarios.

In this work, we have proposed two new methods for the synthesis of [TcO2L4]+ (where L = im-idazole (Im), methylimidazole (MeIm)) complexes using thiourea (Tu) and Sn(II) as reducing agents. The main and by-products of the reactions were determined, and possible reaction mechanisms were proposed. We have shown that the reduction of Tc(VII) with thiourea is ac-companied by the formation of the Tc(III) intermediate and further oxidation to Tc(V). The reac-tion conditions changing can lead to the formation of Tc(VII) and Tc(IV) salts. Seven new crystal structures are described in this work: Tc(V) complexes, salts with Tc(VII) and Tc(IV) anions. For halide salts of Tu the cell parameters were determined. In all obtained compounds, except for [TcO2(MeIm)4]TcO4, there are π-stacking interactions between aromatic rings. An increase in the anion size lead to weaken intermolecular interactions. Halogen bonds and anion-π interactions have also been found in hexahalide-containing compounds. The Hirshfeld surface analysis showed that the main contribution to the crystal packing is made by van der Waals interactions of the H···H type (42.5–55.1%), H···C/C ···H (17.7–21.3%) and hydrogen bonds, which contribute 15.7–25.3% in total.

Due to the fact that to date, the question of the origin of SARS-CoV-2 has not been resolved yet, the author analyzed the main advances in the development of genetic engineering of viruses that took place before the onset of the COVID-19 pandemic. The first artificial genetically modified viruses could appear in nature in the mid-1950s. The technique of nucleic acid hybridization was developed by the end-1960s. In the late 1970s, a method called the "reverse genetics" emerged to synthesize RNA and DNA molecules. In the early 1980-s, it became possible to combine the genes of different viruses and insert the genes of one virus into the genome of another virus. Since that time, the production of vector vaccines began. Currently, by modern technologies one can assemble any virus based on the nucleotide sequence available in the virus database or designed by a computer as a virtual model.Scientists around the world are invited to answer the call of Neil Harrison and Jeffrey Sachs of Columbia University, for a thorough and independent investigation into the origin of SARS-CoV-2. Only a full understanding of the origin of the new virus can minimize the likelihood of a similar pandemic in the future.

We study factorization properties of continuous homomorphisms defined on subgroups (or submonoids) of products of (para)topological groups (or monoids). A typical result is the following one: Let $D=\prod_{i\in I}D_i$ be a product of paratopological groups, $S$ be a dense subgroup of $D$, and $\chi$ a continuous character of $S$. Then one can find a finite set $E\subset I$ and continuous characters $\chi_i$ of $D_i$, for $i\in E$, such that $\chi=\big(\prod_{i\in E} \chi_i\circ p_i\big)\hs1\res\hs1 S$, where $p_i\colon D\to D_i$ is the projection.

A concept of guided artillery rockets with reusable first stage otherwise called a rocket launcher aircraft (RLA) is presented. RLA raises the second stage rockets (SSR) to an altitude of up to 20 km. While RLA is moving at low supersonic speed, it releases one or more SSRs. RLA returns to the base within a few minutes of it’s launch. SSRs use slow burning motors to gain altitude and velocity. At the apogee of their flight SSRs release projectiles which fly to the target and strike it at high impact velocity. The projectiles reach a target at ranges of up to 374 km and impact velocity up to 1.35 km/s. We show that a rocket launched at high altitude and high initial velocity does not need expensive thermal protection to survive ascent. Delivery of munitions to target by the system described should be much less expensive than delivery by a conventional rocket. All parameters of RLA, SSR, and their trajectories are calculated based on theoretical (mechanical and thermo-dynamical) analysis and on several MatLab programs.

Currently there are strong and sustained growth trends observed in multi-disciplinary industrial technologies such as building-integrated photovoltaics and agrivoltaics, where renewable energy production is featured in building envelopes of varying degrees of transparency. Novel glass products can provide a combination of thermal energy savings and solar energy harvesting, enabled by either patterned-semiconductor thin-film energy converters on glass substrates, or by using luminescent concentrator-type approaches to achieve high transparency. Significant progress has been demonstrated recently in building integrated solar windows featuring visible light transmission of up to 70%, with electric power outputs of up to Pmax ~ 30-33 Wp/m2. Several slightly different designs were tested during 2021-2023 in a greenhouse installation at Murdoch University in Perth, Western Australia. The objective of this paper is to report on the field performance of these PV windows in the context of agrivoltaics, and to provide some detail of the performance differences measured in several solar window designs related to their glazing structure materials. Methods for the identification and quantification of long-term field performance differences and energy generation trends in solar windows of marginally different design types are reported. The paper also aims to outline the practical application potential of these transparent construction materials in built environments, focussing on the measured renewable energy figures and seasonal trends observed during the long-term study.

This article is the fourth part of a scientific project under the general title “Geometrized vacuum physics based on the Algebra of Signatures". In the first three articles [1,2,3], the foundations of the Algebra of Stignatures were laid and the main aspects of the kinematics of vacuum layers were considered. This article continues the development of the mathematical apparatus of the proposed project, in particular, the dynamics of vacuum layers is developed based on the Algebra of Signatures. The development of this direction of research (with simplifications related to Riemann's differential geometry) led to the possibility of a geometrized representation of the electric field strength and magnetic field induction. This geometrized mathematical apparatus allows one to interpret the electromagnetic field as an interweaving of accelerated and rotational flows of the adjacent layers of vacuum. The proposed dynamic models of accelerated movements and rotations of vacuum layers can provide a theoretical basis for the development of “zero” (i.e. vacuum) technologies.

This article is the third part of a scientific project under the general title "Geometrized vacuum physics based on the Algebra of Signatures". In the first two papers [1,2], the ideal (i.e., non-curved and immobile) local region of vacuum was studied and the foundations of the Algebra of Signatures were laid. This article considers the possibilities of describing the curved and moving state of the same vacuum region on the basis of the mathematical apparatus of the Algebra of Signatures. The reasons for the multilateral consideration of vacuum and twisting of intra-vacuum processes into spiral bundles are disclosed. The 4-tensor is introduced for two-sided and 16-sided consideration of the curvature of the local vacuum region. On the basis of kinematic models, the following assumptions were made: about the inert properties of vacuum layers; about the possibility of displacement of vacuum layers relative to each other at a speed significantly exceeding the speed of light; about the possibility of "rupture" of the local region of vacuum. The proposed kinematic models of the movement of vacuum layers can be a theoretical basis for the development of "zero" (i.e., vacuum) technologies.

This article is the first part of a scientific project under the general title "Geometrized Vacuum Physics". This study is based on two main postulates: 1) independence of the propagation velocity of electromagnetic waves in vacuum from their frequency; 2) the constancy of the averaged zero vacuum balance, associated with the assertion that only mutually opposite formations are born from vacuum, so that on average they completely compensate for each other's manifestations. In this part of the "Geometrized Vacuum Physics" the foundations of the Algebra of Stignatures are laid, which is the mathematical and logical foundation of the entire project. In the next articles of this project it will be shown that the Algebra of Stignatures can be used for the development of "zero" (vacuum) technologies, algebraic genetics, vacuum cosmology, the vacuum standard model of "elementary particles", vacuum gravity and levitation, vacuum energy, ethics and aesthetics and many other branches of knowledge. At the end of this article, one of the many possible applications of the Algebra of Stignatures is given, in particular, the basics of the stignature-spectral analysis are outlined, with the help of which the possibilities of communication channels can be significantly expanded.

This article is the second part of a scientific project under the general name "Geometrized vacuum physics". On the basis of the Algebra of Stignatures presented in the previous article [1], this article develops the main provisions of the Algebra of Signatures. Both of the above algebras are aimed at studying the properties of an ideal vacuum, but at the same time they are universal and can be applied in various branches of knowledge. It is shown that the signature of a quadratic form is related to the topology of the metric space for which the given quadratic form is a metric. Conditions are given under which an additive imposition of metric spaces with different topologies (or signatures) leads to a total Ricci flat space similar to a Calabi-Yau manifold. A spin-tensor representation of metrics with different signatures is considered and a Dirac bundle of quadratic forms is presented. This article does not contain physical applications of the Algebra of Signatures, but the potential power of this mathematical apparatus will be demonstrated in subsequent articles of this project.

Prospects for predicting the fragmentation of polypeptide chains during their enzymatic hydrolysis using proteolysis models are considered. The opening of the protein substrate during proteolysis and the exposure of its internal peptide bonds for a successful enzymatic attack, the so-called demasking process, were taken into account. The two-step model of proteolysis was used, including the parameters of peptide bond demasking and hydrolysis rate constants for various peptide bonds. Herein, we presented an algorithm for calculating the concentrations of peptide fragments depending on the hydrolysis time or the degree of hydrolysis. The intermediate peptide fragments with two or one internal specific bonds were considered. The fragmentation of β-lactoglobulin (b-LG) with trypsin was predicted, and the calculated concentration curves for peptide fragments were compared with the experimental dependences of concentrations on the degree of hydrolysis. Numerical parameters characterizing the kinetic curves were proposed for the intermediate and final peptide fragments, and they were used to compare the calculated and experimental dependences. The predicted distribution of peptide fragments corresponded to the experimental data on the peptide release during proteolysis of b-LG by trypsin.

The scientific work posted on the Internet, which its author constantly keeps up to date, will be called an alive publication. The genre of alive publishing has many attractive features. However, it requires a certain expansion of the composition of the meta-attributes of the publication: along with the traditional attributes, the date of the appearance of the new, fresh revision is brought to the fore here. Such date is placed in a prominent place in the text of the publication. Along with this, it becomes highly desirable to include such a dynamically ("on the fly") generated date in a bibliographic reference to an alive publication. The currently used methods of dynamic extraction of this date are considered for a simple online publication, for a publication that has received a DOI through Crossref, for a publication posted in arXiv and in Preprints. Thanks to adding this meta-attribute, references to alive publications will beautify any bibliographic list.

The aim of the article is to develop geometrized physics of a vacuum on the basis of two basic postulates: 1) the constancy of the speed of light (more precisely, the speed of propagation of electromagnetic waves) in the vacuum; 2) the ‘vacuum balance condition’ associated with the statement that only mutually opposite formations are born from the vacuum, so that, on average, they completely compensate of the manifestations of each other. The Algebra of signatures is proposed as a mathematical basis for geometrized physics of a vacuum.

Ultrasonic based inspection of thin-walled structures often requires prior knowledge of their mechanical properties. Their accurate estimation could be achieved in a non-destructive manner employing, e.g., elastic guided waves. Such procedures require efficient approaches for experimental data extraction and processing, which is still a challenging task. An advanced automated technique for material properties identification of an elastic waveguide is proposed in this investigation. It relies on the information on dispersion characteristics of guided waves, which are extracted by applying the matrix pencil method to the measurements obtained via laser Doppler vibrometry. Two objective functions have been successfully tested, and the advantages of both approaches are discussed (accuracy vs computational costs). The numerical analysis employing the synthetic data generated via the mathematical model as well as experimental data shows that both approaches are stable and accurate. The influence of the presence of various modes in the extracted data is investigated. One can conclude that the influence of the corruptions related to the extraction of dispersion curves is not critical if the majority of guided waves propagating in the considered frequency range are presented. Possible extensions of the proposed technique for damaged and multi-layered structures are also discussed.

The concept of using eye-tracking in virtual reality for education has been researched in various fields over the past years. With this review, we aim to discuss the recent advancements and applications in this area, explain the technological aspects, highlight the advantages of this approach and inspire interest in the field. Eye-tracking has already been used in science for many decades and now has been substantially reinforced by the addition of virtual and augmented reality technologies. The first part of the review is a general overview of eye-tracking concepts and its applications. In the second part, the focus shifted towards application of eye-tracking in virtual reality. The third part is the description of the recently emerged concept of eye-tracking in virtual reality when applied to education and studying, which has not been thoroughly described before. We describe the main findings, technological aspects and advantages of this approach.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

We discuss the renormalization of the polarizability of a nanoparticle in the presence of either (i) a continuous graphene sheet or (ii) a plasmonic graphene grating, taking into account retardation effects. Our analysis demonstrates that the excitation of surface plasmon-polaritons in graphene produces a large enhancement of the real and imaginary parts of the renormalized polarizability. We show that the imaginary part can be changed by a factor of up to 100 relatively to its value in the absence of graphene. We also show that the resonance in the case of the grating is narrower than in the continuous sheet. In the case of the grating it is shown that the resonance can be tuned by changing the grating geometric parameters.

Chronobiotics is a group of drugs utilized to modify circadian rhythms targeting clock-associated molecular mechanisms. The circadian clock is known as a controller of numerous processes standing behind aging. Hypothesis: KL001 and KS15 targeting CRY, affect lifespan, locomotor activity and circadian rhythm of Drosophila melanogaster. We observed a slight (2%, p<0.001) geroprotective effect on median lifespan (5 µM solution of KL001 in 0.1% DMSO) and a 14% increase in maximum lifespan in the same group. KS15 10 µM solution extended males’ median lifespan by 8% (p <0.05). The statistically significant positive effects of KL001 and KS15 on lifespan were not observed in female flies. KL001 5 µM solution improved locomotor activity in young male imagos (p<0.05) and elevated morning activity peak in aged imagos and modified robustness of circadian rhythms, leaving the period intact. KS15 10 µM solution decreased the locomotor activity in constant darkness and minimized the number of rhythmic flies. KL001 5 µM solution improved by 9% the mean starvation resistance in male flies (p<0.01), while median resistance was elevated by 50% (p<0.0001). This phenomenon may suggest the presence of the mechanism associated with improvement of fat body glucose depos’ utilization in starvation conditions which is activated by dCRY binding KL001.

Studies have shown that in many practical applications, data interpolation by splines leads to better approximation and higher computational efficiency as compared to data interpolation by a single polynomial. Data interpolation by splines can be significantly improved if knots are allowed to be free rather than at a priori fixed locations such as data points. In practical applications, the smallest possible curvature is often desired. Therefore, optimal splines are determined by minimizing a derivative of continuously differentiable functions comprising the spline of the required order. The problem of obtaining an optimal spline is tantamount to minimizing derivatives of a nonlinear differentiable function over a Banach space on a compact set. While the problem of data interpolation by quadratic splines has been accomplished analytically, interpolation by splines of higher orders or in higher dimensions is challenging. In this paper, to overcome difficulties associated with the complexity of the interpolation problem, the interval over which data points are defined, is discretized and continuous derivatives are substituted by their discrete counterparts. It is shown that as the mesh of the discretization approaches zero, a resulting near-optimal spline approaches an optimal spline. Splines with the desired accuracy can be obtained by choosing an appropriate mesh of the discretization. By using cubic splines as an example, numerical results demonstrate that the linear programming (LP) formulation, resulting from the discretization of the interpolation problem, can be solved by linear solvers with high computational efficiency and resulting splines provide a good approximation to the optimal splines.

This study explores how to delineate Russian cities in order to make them comparable on the world scale. In doing so we introduce the concept of large urban regions (LUR) applicable to the Russian urban context. This research is motivated by a principal research question: how to construct a statistical urban delineation, which would allow first, to demonstrate integration of cities into globalization, and second, to make global urban comparative research. Previous studies on urban delineation in Russia have focused almost exclusively on functional urban areas, which have substantial limitations and are not suitable for global urban comparisons. Addressing this research gap, we propose a new definition of Large Urban Regions (LUR). In doing so, first, we introduce the context of Russian cities (2), then we discuss existing Russian urban concepts (3), and justify a need for a new urban delineation (4). Afterwards, we present a general method to delineate Large Urban Regions in Russian context (5.1), and illustrate it in the two case studies of St. Petersburg (polycentric region) and Samara (monocentric region) (5.2). In the last part (6), we discuss the 10 the largest urban regions in Russia and describe a constructed database including all Russian LURs.

This study aims to understand the current state of research in urban resilience and to open a discussion about multi-level perspectives for this concept. Starting with the history of the concept of resilience, we identify three main stages in resilience concept’s evolution: conceptualization, contextualization and operationalization. Confusion occurs between sustainability and resilience, therefore we clearly separate these two concepts by creating conceptual maps. Such maps also underline the specificities of urban and regional resilience discourses. We illustrate that urban resilience research, operating within intra-urban processes, is oriented towards natural disasters, while regional resilience research, operating mostly within inter-urban processes, is oriented towards economic shocks. We show that these two approaches to resilience – urban and regional – are complementary, and we propose to integrate them into a multi-level perspective. By combining these two discourses, we propose a multi-level approach to urban resilience that takes into account both top-down and bottom-up resistance processes. In the discussion section, we propose to take the panarchy perspective as a theoretical framework for multi-level urban resilience, that explains the interactions between different levels through adaptive cycles, relationships between which can help to explain urban resilience.

MPC (Magneto-Photonic Crystal) Optimisation is a feature-rich Windows software application designed to enable researchers to analyze the optical and magneto-optical spectral properties of multilayers containing gyrotropic constituents. A set of computational algorithms aimed at enabling the design optimization and optical or magneto-optical (MO) spectral analysis of 1D magnetic photonic crystals (MPC) is reported, together with its Windows software implementation. Relevant material property datasets (e.g., the optical spectra of refractive index, absorption, and gyration) of several important optical and MO materials are included, enabling easy reproduction of the previously published results from the field of MPC-based Faraday rotator development, and an effective demonstration-quality introduction of future users to the multiple features of this package. We also report on the methods and algorithms used to obtain the absorption coefficient spectral dispersion datasets for new materials, for which the film thickness, transmission spectrum, and refractive index dispersion function are known.

We measured the ring collection coefficient of bromide anion oxidation products in a neutral and slightly alkaline medium on a rotating ring-disk electrode (glassy carbon disk, platinum ring) varying the following parameters: disk electrode rotation velocity, sodium bromide concentration, pH of the medium (in the range of 6 – 12), anode current on the disk and the electroreduction potential of the bromide anion oxidation products on the ring. The data obtained is presented via dependences of the cathode ring current to the disk current ratio vs the ring electrode potential. The analysis of the results was carried out by comparing the experimental polarization curves of the ring electrode with the data of cyclic voltammetry in model solutions to determine the electrical activities of various bromine compounds in positive oxidation states. We claim that RRDE method could be used to obtain quantitative and qualitative data on the electrooxidation of bromide ion in neutral and alkaline solutions. For the most effective regeneration of the spent oxidizer the values of pH &gt; 10 and moderate concentrations of NaBr should be used.

Laminate structures composed of stiff plates and thin soft interlayers are widely used in aerospace, automotive and civil engineering encouraging the development of reliable non-destructive strategies for their condition assessment. In the paper, elastodynamic behaviour of such laminate structures is investigated with emphasis on its application in ultrasonic based NDT and SHM for the identification of interlayer mechanical and interfacial contact properties. A particular attention is given to the practically important frequency range, in which the wavelength considerably exceeds the thickness of the film. Three layer model with spring-type boundary conditions employed for imperfect contact simulation is used for numerical investigation. Novel effective boundary conditions are derived via asymptotic expansion technique and used for analysis of the peculiar properties of elastic guided waves in considered laminates. It is revealed that the thin and soft film influences the behaviour of the laminate mainly via the effective stiffnesses being a combination of the elastic moduli of the film, its thickness and interface stiffnesses. To evaluate each of these parameters separately (or to figure out that the available experimental data are insufficient), a step-wise procedure employing the effective boundary conditions is proposed and tested versus the laser Doppler vibrometry data for Lamb waves in Aluminium/Polymer film/Alumunium structure. The possibility of using film-related thickness resonance frequencies to estimate the film properties and contact quality is also demonstrated. Additionally, the rich family of edge waves is also investigated, and the splitting of fundamental edge waves into pairs is revealed.

Premalignant lesions in the bronchial epithelium represent early stages of squamous cell lung carcinoma, challenging to detect with conventional methods. While previous studies have focused on gene expression, here we examine transcriptomic alterations associated with lesion development with the emphasis on protein-coding transcripts. We reanalyzed publicly available RNAseq dataset on airway epithelial cells from 82 smokers with and without premalignant lesions. Transcript abundances were quantified using kallisto, and differential expression and transcript usage analysis was conducted using the sleuth and RATs packages. Functional characterization included overrepresentation analysis (clusterProfiler), weighted co-expression network analysis (WGCNA), and network analysis (Enrichr-KG). We detected 5,906 differentially expressed transcripts, with significant enrichment in pathways related to oxidative phosphorylation and mitochondrial function. Transcript-level WGCNA identified single module correlated with dysplasia status, enriched in cilium-related biological processes. Analysis of hubs within this module highlighted key genes including RABL2B, DNAH1, EFHC1 and VWA3A, and revealed transcription factors such as FOXJ1 and ZNF474 as potential regulators. Our findings underscore the value of transcript-level analysis in uncovering novel insights into premalignant lesion biology. By examining transcripts rather than genes, we identified potential biomarkers associated with early lung carcinogenesis.

The qualitative analysis of nanodiamonds by FTIR spectrometry as photoacoustic (PAS), diffuse-reflectance (DRIFT), and attenuated total reflection (ATR) modalities was evaluated for rapid and nondestructive analysis and comparison of nanodiamonds. The spectra reproducibility and signal-gathering depth was compared. The assignment of characteristic bands showed that only six groups of bands were present in spectra of all the modalities with appropriate sensitivity: 1760 (C=O stretch, isolated carboxyl groups); 1640–1632 (H–O–H bend, liquid water); 1400–1370 (non-carboxyl C–O–H in-plane bend and CH2 deformation); 1103 (non-carboxyl C–O stretch); 1060 (in-plane C–H bend, non-aromatic hydrocarbons and carbohydrates); and 940 cm–1 (out-of-plane carboxyl C–O–H bend). DRIFT provides the maximum number of bands and is capable of measuring hydrogen-bonded bands and CHX groups. ATR provides the good sensitivity for water and C–H/C–C bands in the range 2000–400 cm–1. PAS-FTIR reveals less bands than DRIFT but more intense bands than ATR-FTIR and shows the maximum sensitivity for absorption bands that do not appear in ATR-IR spectra and are expedient for supporting either DRIFT or PAS along with depth-profiling. Thus, all three modalities are required for full characterization of nanodiamonds surface functional groups.

Downward short-wave (SW) solar radiation is the only essential energy source powering the atmospheric dynamics, ocean dynamics, biochemical processes, etc. on our planet. Clouds are the main factor limiting the SW flux over the land and the Ocean. For the accurate meteorological measurements of the SW flux one needs expensive equipment - pyranometers. For some cases where one does not need golden-standard quality of measurements, we propose estimating incoming SW radiation flux using all-sky optical RGB imagery which is assumed to incapsulate the whole information about the SW flux. We used DASIO all-sky imagery dataset with corresponding SW downward radiation flux measurements registered by an accurate pyranometer. The dataset has been collected in various regions of the World Ocean during several marine campaigns from 2014 to 2022, and it will be updated. We demonstrate the capabilities of several machine learning models in this problem, which are multilinear regression, Random Forests, Gradient Boosting and convolutional neural networks (CNN). We also applied the inverse target frequency (ITF) re-weighting of the training subset and the approach of pre-classification in order to raise the SW flux approximation quality. We found that the CNN is capable of approximating downward SW solar radiation with higher accuracy compared to existing empiric parameterizations. We also found that the ITF reweighting of the training subset increases the approximation quality substantially. The estimates of the SW radiation flux using all-sky imagery may be of particular use in case of the need for the fast radiative budgets assessment of a site.

Numerical methods, including machine learning methods, are now actively used in the applications related to guided wave propagation. The method proposed in this study for material properties characterization is based on the algorithm of the clustering of multivariate data series obtained as a result of the application of the matrix pencil method to the experimental data. In the proposed technique, multi-objective optimization is employed to improve the accuracy of particular parameter identification. At the first stage, the computationally efficient method based on the calculation of the Fourier transform of Green's matrix is employed iteratively and the obtained solution is used for the filter construction with decreasing bandwidth, which allows us to obtain nearly noise-free classified data (with mode separation). The filter provides data separation between all guided waves in a natural way, which is needed at the second stage, where the slower method based on the minimization of the slowness residuals is applied to the data. The method might be applied for material properties identification in plates with thin coatings/interlayers, multi-layered anisotropic laminates etc.

A study of photovoltaic solar window technologies is reported, focusing on their structural features, functional materials, system development, and suitability for use in practical field applications, e.g. public infrastructures and agricultural installations. Energy generation performance characteristics are summarized and compared to theory-limit predictions. Working examples of pilot-trial solar window-based installations are described. We also report on achieving electric power outputs of about 25 W_p/m² from clear and transparent large-area glass-based solar windows.

We present a review of the current state of the field for a rapidly evolving group of technologies related to solar energy harvesting in built environments. In particular, we focus on recent achievements in enabling the widespread distributed generation of electric energy assisted by energy capture in semi-transparent or even optically clear glazing systems and building wall areas. Whilst concentrating on the cutting-edge recent results achieved in the integration of traditional photovoltaic device types into novel concentrator-type windows and glazings, we compare the main performance characteristics reported with these achievable using more conventional (opaque or semi-transparent) solar cell technologies. A critical overview of the current status and future application potential of multiple existing and emergent energy harvesting technologies for building integration is provided.

Amorphous ferrite-type rare-earth (RE) substituted garnets and garnet-oxide nanocomposite layers are prepared on clear glass substrates by using RF magnetron sputter-deposition process. By using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method, the spectral dispersion function of optical constants and the layer thicknesses are derived accurately from the transmission spectra of the as-deposited samples. The effects of excess metal-oxides added to the base material systems during the co-deposition process are found to affect the refractive index and the optical absorption coefficients of garnet-oxide composites. A number of optical constant datasets are presented, enabling the experimentalists to design nanophotonic or integrated-optics devices employing these functional materials.

X-band marine radar captures signal reflected from the sea surface. Theoretical studies indicate that the initial unfiltered signal contains meaningful information including parameters related to wind waves. Traditional methods for estimating significant wave height (SWH) rely on the physical laws describing signal reflection from rough surfaces. However, recent studies suggest the feasibility of employing artificial neural networks (ANNs) for SWH approximation. Both classical and ANN-based approaches necessitate costly in situ data. In this study, we propose generating synthetic radar images with specified wind wave parameters using Fourier-based approach and Pierson–Moskowitz wave spectrum as a viable alternative. We generate synthetic images and use them for unsupervised learning approach to train a convolutional component of an ANN. After that, we train a regression ANN based on the previous convolutional component to obtain SWH back from synthetic images. Then, we apply preliminary trained weights for the same regression model to train SWH approximation on the dataset of real sea clutter images. In this study, we demonstrate the increase in the accuracy of SWH estimation from radar images with the preliminary training on synthetic data.

The optimal regime of three-photon resonant excitation of a helium atom by a femtosecond ul-traviolet (UV) pulse was discovered and numerically studied, at which the maximum power of the third harmonic of the UV field is achieved in the spectrum of dipole acceleration (the second time derivative of the induced dipole moment) of the atom. It is shown that the optimal frequency of the UV field nearly coincides with the frequency of the three-photon transition 1s2 – 1s2p, taking into account its shift as a result of the dynamic Stark effect, and the intensity of the UV field is dictated by the condition of maximizing the product of the populations of the 1s2 and 1s2p states, averaged over the time interval during which the UV field is non-zero. For the considered UV field durations, from 10 to 100 cycles of the carrier frequency (from units to tens of femtoseconds), the optimal intensity lies in the range from 10^14 W/cm^2 to several units of 10^14 W/cm^2. It is shown that with an optimal choice of the frequency and intensity of the UV field, the dynamics of excitation of bound and continuum states, as well as the shape of the time envelope of the dipole acceleration of the atom, weakly depend on the duration of the UV field envelope; only their time scale changes significantly. In addition, under the optimal conditions the average power of the third harmonic signal in the dipole acceleration spectrum is practically independent of the duration of the UV field envelope.

Despite a significant number of investigations in the field of phosphazene chemistry, the mechanism of this class cyclic compounds formation is still poorly studied. At the same time, a thorough understanding of this process is necessary both for the direct production of phosphazene rings with a given size, and for the controlled cyclization reaction when it is secondary and undesirable. Here we have synthesized a series of short linear phosphazene oligomers with the general formula Cl[PCl2=N]n–PCl3+PCl6– and studied their tendency to form cyclic structures under the influence of elevated temperature or in the presence of nitrogen-containing agents, such as hexamethyldisilazane (HMDS) or ammonium chloride. It was established that linear oligophosphazenes are inert when heated in the absence of the mentioned cyclization agents, and the formation of cyclic products occurs only when these agents are involved in the process. It is for the first time shown the ability to obtain the desired size phosphazene cycle from corresponding linear chain. Known obstacles like side interaction with the PCl6– counterion and a tendency of longer chains to undergo crosslinking elongation instead of cyclization are still relevant and ways to overcome them are being discussed.

The planned closure of potash mines, achieved through the injection of highly mineralized brines into the worked-out area, is a complex and not fully studied process. A critical concern arises when brines obstruct the aerodynamic connections between the flooded mine's airspace and the atmosphere, potentially leading to the formation of closed cavities where explosive gases can accumulate. To address this hazard, it is imperative to develop systems capable of extracting the gas-air mixture from the unflooded domed portions of the worked-out area. This is the focus of this study, in which we analyze gas-dynamic processes within the potassium mine worked-out area during planned flooding. Two distinct scenarios are examined: the first involves controlled flooding with saturated brines, while the second contemplates flooding resulting from a hypothetical breakthrough of supra-salt strata, leading to the ingress of groundwater into the worked-out area. A novel mathematical model is introduced to predict the evolution of gas-air mixture parameters in the unflooded dome segment of the worked-out area. Utilizing this model, we assess the effectiveness of proposed measures designed to eliminate explosive gases from the worked-out area. Specifically, a pipeline system is proposed for the removal of gases, followed by their dilution below the maximum permissible concentrations in the effluent jet. The findings from this study contribute valuable insights into ensuring the safe and efficient closure of potash mines, shedding light on potential risks and effective mitigation strategies for gas-related hazards during planned flooding.

Transport of carbon, major and trace element by rivers in permafrost-affected regions is one of the key factor of circumpolar aquatic ecosystem response to climate warming and permafrost thaw. While seasonal and annual export fluxes (yields) of carbon (C) and inorganic solutes are fairly well known for all large Arctic rivers, spatial variations in elementary concentration along the river length and among its tributaries remain poorly understood. Moreover, the landscape factors controlling riverine element concentration in permafrost-affected regions are still poorly constrained. This is especially true for the largest river of Eastern Siberia, the Lena River, which drains through continuous permafrost zones with highly variable lithology and vegetation. Here we present the results of C, major and trace element measurements over a 2600-km transect of the Lena River main stem (upper and middle reaches) including its 30 tributaries, conducted at the peak of the spring flood. There were two main group of solutes in the main stem depending on their spatial pattern: i) elements that decreased their concentrations downstream, from SW to NE (Cl, SO4, DIC, Li, B, Na, Mg, K, Ca, As, Sr, Mo, Sb, Ba and U), which probably reflected a decrease in the proportion of carbonate rocks in the watershed and the degree of groundwater feeding, and ii) elements that increased their concentrations downstream (Al, Ti, Cr, Fe, Ga, Rb, Y, Zr, Nb, Cs, REEs, Hf and Th), which was tentatively linked to an increase in organic C stock in soils, larch forest coverage and enhanced mobilization of lithogenic elements from silicate soil minerals. Based on landscape parameters of Lena tributaries, we tested the impact of major environmental factors on major and trace element spatial pattern. Among all the variables, the proportion of sporadic permafrost on the watershed strongly controlled concentrations of soluble highly mobile elements (Cl, B, DIC, Li, Na, K, Mg, Ca, Sr, Mo, As and U). Another important factor of element concentration control in the Lena River tributaries was the coverage of watershed by light (B, Cl, Na, K, U) and deciduous (Fe, Ni, Zn, Ge, Rb, Zr, La, Th) needle-leaf forest (pine and larch). The latter, however, could also reflect the DOC-enhanced transport of low-soluble trace elements in the NW part of the basin. This part of the basin is dominated by silicate rocks and continuous permafrost, as compared to carbonate rock-dominated and groundwater-affected SW part of the Lena River basin. Overall, the impact of rock lithology and permafrost on major and trace solutes of the Lena River basin during the peak of spring flood was mostly detected at the scale of the main stem. Such an impact for tributaries was much less pronounced, because of the dominance of surface flow and lower hydrological connectivity with deep groundwater in the latter. Future changes in the river water chemistry linked to climate warming and permafrost thaw at the scale of the whole river basin are likely to be linked to changes in spatial pattern of dominant vegetation, rather than to the permafrost regime. We argue that comparable studies of large, permafrost-impacted rivers during most contrasting seasons, including winter baseflow, should allow efficient prediction of future changes in riverine ‘inorganic’ hydrochemistry induced by permafrost thaw.

A non-steady state mathematical model of amino acid (phenylalanine (Phe)) and mineral salt (NaCl) solution separation by neutralization dialysis (ND) carried out in a batch mode is proposed. The model takes into account the characteristics of membranes (thickness, ion-exchange capacity and conductivity) and solutions (concentration, composition), as well as the flow rate of the solution in the dialyzer compartments. As compared to previously developed models, the new one considers the local equilibrium of Phe protolysis reactions in solutions and membranes and, also, the transport of all the phenylalanine forms (zwitterionic, positively and negatively charged) through membranes. A series of experiments on ND demineralization of NaCl and Phe mixed solution was carried out. In order to minimize Phe losses, the solution pH in the desalination compartment was controlled by changing the concentrations of the solutions in the acid and alkali compartments of the ND cell. The validity of the model was verified by comparison of simulated and experimental time dependencies of solution electric conductivity and pH, as well as the concentration of Na+, Cl– ions and Phe species in the desalination compartment. Based on the simulation results, the role of Phe transport mechanisms in the losses of this amino acid during ND was discussed.

The retinal pigment epithelium (RPE), which ensures the normal functioning of the neural retina, is a pigmented single-cell layer that separates the retina from the Bruch's membrane and the choroid. There are three main types of pigment granules in the RPE cells of the human eye: lipofuscin granules (LG) containing the fluorescent “age pigment” lipofuscin, melanoprotein granules (melanosomes, melanolysosomes) containing the screening pigment melanin and complex melanolipofuscin granules (MLG) containing simultaneously both types of pigments - melanin and lipofuscin. This review examines the functional role of pigment granules in the aging process and in the development of oxidative stress and associated pathologies in RPE cells. The focus is on the process of light-induced oxidative degradation of pigment granules caused by reactive oxygen species. The reasons leading to increased oxidative stress in RPE cells as a result of oxidative degradation of pigment granules are considered. A mechanism has been proposed to explain the phenomenon of age-related decline in melanin content in RPE cells. The essence of the mechanism is that when the lipofuscin part of the melanolipofuscin granule is exposed to light, reactive oxygen species are formed, which destroy its melanin part. As more melanolipofuscin granules are formed with age and the development of degenerative diseases, the melanin in pigmented epithelial cells ultimately disappears.

The continuous advancements in healthcare technology have empowered the discovery, diagnosis, and prediction of diseases, revolutionizing the field. Artificial intelligence (AI) is expected to play a pivotal role in achieving the goals of precision medicine, particularly in disease prevention, detection, and personalized treatment. This study aims to determine the optimal combination of the mother wavelet and AI model for the analysis of pediatric electroretinogram (ERG) signals. The dataset, consisting of signals and corresponding diagnoses, undergoes Continuous Wavelet Transform (CWT) using commonly used wavelets to obtain a time-frequency representation. Wavelet images were used for the training of five widely used deep learning models: VGG-11, ResNet-50, DensNet-121, ResNext-50, and Vision Transformer, to evaluate their accuracy in classifying healthy and unhealthy patients. The findings demonstrate that the combination of Ricker Wavelet and Vision Transformer consistently yields the highest median accuracy values for ERG analysis, as evidenced by the upper and lower quartile values. The median balanced accuracy of the obtained combination of the three considered types of ERG signals in the article are 0.83, 0.85, and 0.88. However, other wavelet types also achieved high accuracy levels, indicating the importance of carefully selecting the mother wavelet for accurate classification. The study provides valuable insights into the effectiveness of different combinations of wavelets and models in classifying ERG wavelet scalograms.

Lead-based ternary chalcogenide thin films of the (PbTe)1-x(PbS)x system were obtained by plasma-enhanced chemical vapor deposition technique (PECVD) under conditions of a nonequilibrium low-temperature argon plasma of an RF discharge (40.68 MHz) at a reduced pressure (0.01 Torr). High-purity elements were directly used as starting materials – Pb, S and Te. Plasma-chemical synthesis was carried out on the surface of of c-sapphire and silicon substrate. The physicochemical properties of the films were studied by various analytical methods. The dependence of the Seebeck coefficient, resistivity, and power factor on the structural properties and composition has been studied. The thermoelectric characteristics were found to be dependent on the film composition. Upon the selection of optimal sulfur concentration one can increase the power factor as compared to single phase PbS ot PbTe films.

Estimating the vehicle crashworthiness parameters experimentally is expensive and time consuming. For these reasons different modelling approaches are utilized to predict the vehicle behaviour and reduce the need for full-scale crash testing. The earlier numerical methods used for vehicle crashworthiness analysis were based on the use of lumped parameters models (LPM), a combination of masses and nonlinear springs interconnected in various configurations. Nowadays, the explicit nonlinear finite element analysis (FEA) is probably the most widely recognized modelling technique. Although informative, finite element models (FEM) of vehicle crash are expensive both in terms of man-hours put into assembling the model and related computational costs. A simpler analytical tool for early analysis of vehicle crashworthiness could greatly assist the modelling and save time. In this paper a simple piecewise LPM composed of a mass-spring-damper system, is used to estimate the vehicle crashworthiness parameters, focusing on the dynamic crush and the acceleration severity index (ASI). The model is first calibrated against a full-scale crash test and a FEM, post-processed with the LS-DYNA software, at an impact velocity of 56 km/h. The genetic algorithm is used to calibrate the model by estimating the piecewise lumped parameters (stiffness and damping of the front structure of the vehicle). After calibration, the LPM is applied to a range of velocities (40, 48, 64 and 72 km/h). The predictions for crashworthiness parameters from the LPM were compared with the predictions from the FEA and the results are much similar. It is shown that the LPM can assist in crash analysis, since LPM has some predictive capabilities and requires less computation time in comparison with the explicit nonlinear FEA.

(1) The article is devoted to the development of a theoretical and algorithmic basis for numerical modeling of the spontaneous potential method (SP) as applied to the study of sandy-argillaceous reservoirs. (2) In terms of coupled flows, we consider a physical-mathematical model of SP signals from an electrochemical source, with regard to the case of fluid-saturated shaly sandstone. (3) An algorithm for 2D finite-element modeling of SP signals was developed and implemented in software, along with its internal and external testing with analytical solutions. The numerical SP modeling was carried out, with determining the dependences on the reservoir thickness and porosity, the amount of argillaceous material and the type of minerals. We performed a comparative analysis of the simulated and field SP data, using the results of laboratory core examinations taken from wells in a number of fields in the Latitudinal Ob Region of Western Siberia. (4) The results of the study may be used either for the development of the existing SP techniques, by providing them with a consistent computational model, or for the design of new experimental approaches.

Layout estimation is a challenge of segmenting a cluttered room image into floor, walls and ceiling. We applied Double refinement network proved to be efficient in the depth estimation to generate heat maps for room key points and edges. Our method is the first not using encoder-decoder architecture for the room layout estimation. ResNet50 was utilized as a backbone for the network instead of VGG16 commonly used for the task, allowing the network to be more compact and faster. We designed a special layout score function and layout ranking algorithm for key points and edges output. Our method achieved the lowest pixel and corner errors on the LSUN data set. The input image resolution is 224*224.

Natural cytokinins are a promising group of cytoprotective and anti-tumor agents. In this research, we synthesized a set of novel cytokinin analogs with alkyl substituents at various positions of the aromatic moiety, as well as with oxygen-containing groups, and tested their antiproliferative activity in MDA-MB-231, A-375, and U-87 MG cell lines, and cytoprotective properties in H2O2 and CoCl2 models. Two amino-linked compounds were anti-proliferative with the ability to act synergistically with doxorubicin, and two carbamate-based ones were cytoprotective. According to the molecular docking data, anti-proliferation was based on the A2AR and APRT inhibition and cytoprotection on the CDK2 inhibition. The obtained results are promising for the development of novel anti-cancer therapeutics.

Finding new ways for the preparation of cross-linked structures is a significant problem in terms of materials for biomedical application, lithium batteries electrolytes, and etc. Within this work we have studied the possibility to utilize hydrosilylation and Piers-Rubinsztajn reactions to obtain cross-linked model phosphazene compounds, containing eugenoxy and guaiacoxy groups. It was shown that Piers-Rubinsztajn reaction cannot be efficiently used to prepare tailored polymer-matrix, due to the catalyst deactivation by nitrogen atoms of phosphazene units. A number of cross-linked phosphazene-based materials was obtained with the use of hydrosilylation reaction and their properties were studied by NMR spectroscopy, FTIR, DSC, and TGA. This work showed a perspective for the use of eugenoxy functional groups for the preparation of three-dimensional hybrid phosphazene/siloxane-based materials for various applications.

This paper presents results of the magnetic dynamics study (the microwave power absorptions at the fixed frequencies, during magnetic field sweeping) in samples of Y3Fe5O12 single crystals in the form of plates and spheres of various sizes, at frequencies exceeding 30 GHz, in magnetic fields up to 18 kOe, at room temperature and T=77 K. It was found, that in this case, the inhomogeneity’s of the magnetic state manifested itself in the Y3Fe5O12 samples in as 2D local phase separation regions. These 2D phase separation regions formed inside domain walls representing superlattices with size’s 700 – 900 Å. Landau diamagnetism or de Haas van Alphen oscillations observed in the 2D phase separation regions at room temperature and T=77 K, depending on the shape and size of the studied plates and spheres.

In this study, the extraction of rare earth elements (REEs) from chloride solutions containing mixtures of these metals with solutions of the mixtures of P507 and Cyanex 272 (1:1) of various concentrations was experimentally studied. It was shown that the distribution coefficients of all REEs decrease with increasing concentration of these metals in the initial solution, which is associated with the loading of the organic phase. The most significant improvement in the extraction is observed for heavy group of rare earth elements. The extractability of REEs enhances with increasing atomic number of the element, as is typical for the extraction of these metals with acidic organophosphorus extractants. The data obtained show that separation factors of adjacent rare earth elements mainly decrease with increasing concentration of metals in the initial aqueous solution. Increasing the concentration of the extractant mixture does not have a significant effect on the values of the adjacent REE separation factors. Analysis of the experimental results shows that two commercial products can be obtained from a concentrate of the medium-heavy group. In the first cascade, yttrium can be separated, in the second, a concentrate of dysprosium and terbium can be obtained.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

Working memory (WM) is a brain system for short-term storage and manipulation of information and plays an important role in complex cognitive tasks. In the synaptic theory of WM memorized elements are stored in the form of short-term potentiated connections in a sample population of neurons. In this paper, we show that such populations can be formed due to the mechanisms of spike-timing-dependent plasticity (STDP) – the phase dependence associated with the ratio of the pulse times of the interacting neurons. We propose a WM model considering two types of plasticity: short-term plasticity and STDP. We have shown formation of neuronal clusters encoding items in the WM model, that can be formed by external stimulation of a group of neurons due to the mechanisms of STDP and hold and reactivated by short-term plasticity mechanisms. The dynamic formation of neuronal clusters instead of pre-formed clusters gives additional flexibility to the model.

Nanoporous films of Eu-doped organosilicate glass (OSG) have been synthesized using sol-gel technology and spin-coating, employing evaporation-induced self-assembly (EISA), on silicon wafers. The Eu doping is achieved by dissolution of Eu(NO3)3·6H2O in the precursor solution. The deposited films are characterized by using Fourier transform infrared (FTIR) spectroscopy, ellipsometric porosimetry (EP), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy. It is observed that Eu doping makes the films more hydrophilic and reduces the pore size and open porosity. The reduction Eu3+ → Eu2+ occurs in the pores of OSG films, which is confirmed by depth profiling XPS. However, Eu3+ still presents on the film’s top surface. Presence of Eu3+ and Eu2+ gives characteristic luminescence emission in the range of 600‒630 nm (Eu3+) and 290‒400 nm (Eu2+). The Eu2+/Eu3+ concentrations ratio depends on CH3 groups concentration in the films. Moreover, concentration of Eu2+ ions in the pores can be reduced by exposure in inductively coupled (ICP) oxygen plasma. The observed shift of the luminescence spectra towards the UV region, in comparison to previously reported Eu-doped organosilicate films, can be attributed to the energy transfer occurring between the host material and Eu2+ ions.

Current progress in the prediction of mechanical behavior of solids requires understanding of spatiotemporal complexity of plastic flow caused by self-organization of crystal defects. It may be particularly important in hexagonal materials because of their strong anisotropy and combination of different mechanisms of plasticity, such as dislocation glide and twinning. These materials often display complex behavior even on the macroscopic scale of deformation curves, e.g., a peculiar three-stage elastoplastic transition, the origin of which is a matter of debates. The present work is devoted to a multiscale study of plastic flow in α-Ti, based on simultaneous recording of deformation curves, 1D local strain field, and acoustic emission (AE). It is found that the average AE activity also reveals three-stage behavior, but in a qualitatively different way depending on the crystallographic orientation of the sample axis. On the finer scale, the statistical analysis of AE events and local strain rates testifies to an avalanche-like character of dislocation processes, reflected in power-law probability distribution functions. The results are discussed from the viewpoint of collective dislocation dynamics and are confronted to predictions of a recent micromechanical model of Ti strain hardening.

Micro-grids’ operations offer local reliability; in the event of faults or low voltage/frequency events on the utility side, micro-grids can disconnect from the main grid and operate autonomously while providing the continued supply of power to local customers. With the ever-increasing penetration of renewable generation, however, the operations of micro-grids become increasingly complicated because of the associated fluctuations of voltages. As a result, transformer taps are adjusted frequently, thereby leading to the fast degradation of expensive tap-changer transformers. In the islanding mode, the difficulties also come from the drop of voltage and frequency upon disconnecting from the main grid. To appropriately model the above, the nonlinear AC power flow constraints are necessary. Computationally, the discrete nature of tap-changer operations and the stochasticity caused by renewables add two layers of difficulty on top of a complicated AC-OPF problem. To resolve the above computational difficulties, the main principles of the recently-developed "l1-proximal" Surrogate Lagrangian Relaxation are extended. Testing results based on 9-bus system demonstrate the efficiency of the method to obtain the exact feasible solutions for micro-grid operations thereby avoiding approximations inherent to existing methods, while demonstrating that through the optimization, 1. the number of tap changes is drastically reduced, and 2. the method is capable of handling networks with meshed topologies.

Hyperleptinemia potentiates the effects of many atherogenic factors, such as inflammation, platelet aggregation, migration, hypertrophy, proliferation of vascular smooth muscle cells, and endothelial cell dysfunction. The present study analysed the effects of long-term hyperleptinemia in an in vivo myocardial ischemia-reperfusion model to demonstrate whether the in vivo deleterious effect also affects cardiac structure and function. Rats by were subcutaneously administered leptin for 8 days to estimate the involvement of the JAK/STAT pathway. Data from 58 male Wistar rats were included in the final analysis. Myocardial infarction (MI) was modelled by the 30-minute ligation of the main left coronary artery followed by 120-minute reperfusion. Hemodynamic measurements, electrocardiography monitoring, echocardiography, myocardial infarct size and area at risk, blood biochemical parameters, leptin, IL-6, TNF-alpha, FGF-21, and cardiomyocyte morphology were measured. Statistical analyses were performed using IBM SPSS Statistics v.26. Seven-day hyperleptinemia in rats led to increased an blood pressure and heart rate, myocardial hypertrophy, impaired LV function, an increased frequency of ischemic arrhythmias, dyslipidaemia, systemic inflammation, and an increased size of induced myocardial infarction. The blockade of the JAK/STAT signalling pathway effectively reversed the negative effects of leptin, including increased blood pressure and total cholesterol.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

With the dramatic increase in world population, continued advances in modern greenhouse agriculture and plant growth practices are expected to help overcome the global problem of future food shortages. Next generation greenhouse design practices will need to address a range of issues, ranging from energy and land use efficiency to providing plant-optimised growth techniques. In this paper, we focus on investigating the optimum irradiation spectra matched to the lettuce species (Lactuca sativa, L.), which is commonly grown in greenhouse environments, in order to develop low-emissivity glass panes that maximize the biomass productivity of glass greenhouses. This low-emissivity glass passes the solar spectral components needed for crop growth, while rejecting other unwanted radiations, leading to significant energy savings and other beneficial effects related to greenhouse climate control, in a range of climates. This is due to reducing both the solar heat gain and photosaturation, which can raise the temperature of the crops to harmful levels. Experimental results show that substantial biomass productivity improvements in lettuce (up to ~14.7%) can be attained using spectrally optimized illumination, compared with white light irradiation. We also report on the development of advanced metal-dielectric thin-film filters that produce the optimum illumination spectrum when exposed to sunlight.

The parts obtained by FFF technology are anisotropic in any direction; while the whole part constitutes out of layers, each of the layers include one or more perimeters of shell and the infill with density from 0 to 100%. Mechanical performance of FFF parts depends on its shape, orientation, constitution and 3D printing parameters. A classification for shapes of parts obtained by FFF and stressed during its operation is provided. For the most questionable class (parts with interrupted shell critically stressed on interlayer boundaries) a representative sample and testing apparatus is developed. Different approaches to the sample shape modification were applied and tested. The part shape optimization resulted in increment of the force, required to fracture the part from 483 to 1096 N.

Since 2007, at the Electron Science Research Institute (ESRI) nano-fabrication laboratories, Edith Cowan University, Australia, we have devoted research efforts to the synthesis and characterization of bismuth-containing ferrite-garnet-type thin-film magneto-optic (MO) materials of different compositions. We report on the development and properties of highly bismuth-substituted iron-garnet thin films prepared by using radio frequency (RF) magnetron sputtering. We study the process parameters associated with the RF magnetron sputter deposition technique and investigate the results of optimizing process parameters and implementing several special techniques including the fabrication of co-sputtered nanocomposite films, all-garnet multilayer structures, applying oxygen plasma treatment on amorphous garnet layers just after the deposition process, and designing modifications of the annealing crystallization process and regimes for achieving the best MO properties. We demonstrated significant improvement in MO properties of Bi-containing ferrite-type garnet thin-film materials, including record-high MO figures of merit and improved conventional and un-conventional hysteresis loops of Faraday rotation. The attractive optical, magnetic, and magneto-optic properties obtained in highly bismuth-substituted iron garnet thin-film materials of multiple composition types are relevant in the context of manufacturing next-generation ultra-fast optoelectronic devices, such as light intensity switches and modulators, high-speed flat panel displays, and high-sensitivity sensors.

We report on the field testing datasets and performance evaluation results obtained from a commercial property-based visually-clear solar window installation site in Perth-Australia. This installation was fitted into a refurbished shopping centre entrance porch, and showcases the potential of glass curtain wall-based solar energy harvesting in built environments. In particular, we focus on photovoltaic (PV) performance characteristics such as the electric power output, specific yield, day-to-day consistency of peak output power, and the amounts of energy generated and stored daily. The dependencies of the generated electric power and stored energy on multiple environmental and geometric parameters are also studied. An overview of the current and future application potential of high-transparency, visually-clear solar window-based curtain wall installations suitable for practical building integration is provided.

The study examined eating timing, diet, and the ratio of sleep phases in people with social jetlag (SJL). The study involved 83 participants who filled out a questionnaire, and 21 of them took part in the study of sleep phases by electroencephalography during the week. SJL was associated with a higher incidence rate of eating jetlag, eating phase delays, an increase in calorie intake after 9 p.m., a decrease in dietary fiber intake for breakfast, and melatonin-containing product consumption for dinner. Young people with SJL had a reduction in total sleep and light sleep phase duration by 60 and 36 min on work/school days and an increase in total sleep and REM sleep phase duration by 66 and 60 min on weekends, respectively. Young people consuming foods with more than 4234.5 ng of melatonin for dinner, compared with their peers consuming less than 313.2 ng of melatonin, showed a decrease in SJL and sleep debt by 54 and 90 min and an increase in the total sleep and the deep sleep phase duration by 66 and 30 min, respectively. Thus, the consumption of melatonin-containing foods for dinner is associated with a decrease in circadian misalignment and a sleep quality improvement.

Humanity’s social and economic development has been challenged by a range of adversities over the millennia that have caused widespread and unimaginable suffering. At the same time, these challenges have forced humans to evolve more wisely, overcoming adversity through creativity and leading to advancements in science and technology, medicine, ethics and legal systems, and socio-political systems. The dynamics of risks and opportunities caused by COVID-19, in the built, cyber, social and economic environments, present opportunities for deepening our understanding of resilient and sustainable development and infrastructure. This article reflects on five lessons that COVID-19 is teaching us about what it means to develop sustainably through the lens of transportation: (1) sustainable development planning and analytical frameworks must be comprehensive, for long-term sustainability; (2) multi-modal transportation is a superior vision for sustainable development than any one particular mode; (3) tele-activities are part of an effective infrastructure sustainability strategy; (4) economic capital is critically important to sustainable development even when it is not a critical existential threat, and, (5) effective social capital is essential in global disaster resistance and recovery, and can and must be leveraged between fast-moving and slow-moving disasters. Resilient and sustainable infrastructure will continue to be critical to addressing evolving natural and man-made hazards in the 21^st Century.

Transmission electron microscopy methods were used to analyze the cementite substructure in the head of special-purpose long rails of DT400IK category made of hypereutectoid steel after long-term operation on an experimental track on the Russian Railways ring (the passed tonnage is 187 million tonnes). It is noted that the study of various aspects of cementite – its structure, morphology, chemical composition, crystal lattice defects is relevant. The steel structure is represented by three morphological components at a distance of 10 mm from the sample surface: lamellar perlite, fractured and fragmented perlite. The volume fraction of lamellar perlite in the material is 65%. It is shown that after operation, the cementite plates are bent and separated by ferrite bridges. In the plates of ferrite and cementite, a dislocation substructure is formed which is of chaotically distributed and network type in ferrite and of ordered type in cementite. An increased density of dislocations at ferrite-cementite interfaces compared to the volume of ferrite plates was noted. Two possible mechanisms of deformation transformation of lamellar perlite grains are indicated: fracture of cementite plates and carbon pulling out from the lattice of the carbide phase. It is indicated that in the dissolution of cementite plates, the interfacial boundaries “α-phase-cementite” play an important role. The removal of carbon from cementite plates occurs most intensively near defects in ferrite and cementite. The formed nanosized particles of tertiary cementite are unevenly distributed in the ferrite plates, most of them are observed at the locations of ferrite subgrains and interfacial boundaries. This results in non-uniform diffraction contrast in dark-field images of cementite plates. Nanosized particles of cementite can be taken out into the interlamellar space of pearlite colonies in the process of dislocation slip, or they are formed as a result of deformation decomposition, which is less likely. Fragmentation of ferrite and cementite plates is revealed and azimuthal components of total misorientation angles are estimated. The mechanisms of mass transfer of carbon atoms over interstitial sites, deformation vacancies, dislocation tubes, grain boundaries and fragments are considered. According to all the established patterns of the cementite substructure transformation, a comparison with the results for rails made of hypoeutectoid steel was performed.

In the present paper, we describe several coleoid jaws discovered in the lower Toarcian black shales, cropping out along the Vilyui River (Yakutia, Russia). This is the first record of a Lower Jurassic coleoid jaw outside Europe and the first report of such a finding from the Mesozoic of Siberia. The described coleoid jaws demonstrate the same mode of preservation and morphology as the coeval jaws previously reported from Europe. Their preservation in Siberia became possible due to the widespread occurrence of black shale facies associated with the early Toarcian oceanic anoxic event (TOAE).

We observed and studied the phenomenon of the redox front propagation in different polyaniline (PAni) deposited samples interfaced with liquid or solid polymeric electrolyte. The front of electrochemical conversion, in which the insulator and the conductor parts of PAni are interfaced, is studied observing the temporal evolution of the conductivity of PAni samples. The propagation of redox front was studied in electrochemically obtained thick (2 µm) and in thin (50 nm) poly-aniline films, obtained using Langmuir-Blodgett (LB) method. In the configuration that we tested, the speed of the red-ox front propagation for the thin LB films was found to be 200 micron/sec opening the way for the manufacturing large neural networks, realized using PAni based memristive devices, in which the memristance can be quickly changed in the programmable manner. The prototypes of the spiking neuron connections were manufactured on the basis of lithographically developed gold contacts, bridged by electrochemically grown polyaniline and placed under polymer electrolyte layer with only one counter electrode (gate) for the whole manifold of pseudo-two-terminal memristor bridges. The spike propagation was studied in such gold-polyaniline systems. The research opens the possibility of miniature spike or rate-based neural network circuits manufacture, based on metal pads and polyaniline.

Over the past decade, wireless communication technologies have developed significantly for intelligent applications in road transport. This paper provides an overview of telecommunications-based intelligent transport systems with a focus on ensuring system safety and resilience. In vehicle-to-everything, these problems are extremely acute due to the specifics of the operation of transport networks, which requires the use of special protection mechanisms. In this regard, it was decided to use blockchain as a system platform to support the needs of transport systems for secure information exchange. This paper describes the technological aspects of implementing blockchain technology in vehicle-to-network; the features of such technology are presented, as well as the features of their interaction.

This article discusses the outcomes of a quantitative analysis of the competitiveness of grain and its recycling in the countries-members of the Eurasian Economic Union (EEU) through econometric panel data models. The analysis is based on the data of public authorities’ statistics of the countries-members of the EEU, as well as the United Nations Comtrade Database which is a repository of official international trade statistics. The results of the analysis allow to assess the level of competitiveness of produced agro-food products in the countries-members of the EEU and determine the extent to which various factors affect it. The research conclusions can be used to develop and adjust the agreed with the agro-food policy in the EEU.

Inorganic polyphosphate (polyP) is an important factor of stress tolerance in microbial cells. In yeast, the major enzyme of polyP biosynthesis is Vtc4, a subunit of the vacuole transporter chaperone (VTC) complex. In this study, we demonstrated that Vtc4 knockout in Saccharomyces cerevisiae not only decreased polyP content but also caused shifts in the composition of the intracellular polyP pool and changed the stress tolerance profile. In the mutant S. cerevisiae, the level of short-chain acid-soluble polyPs was decreased nearly 10-fold, whereas that of longer acid-insoluble polyPs was decreased only 2-fold, suggesting the existence of other enzymes compensating the production of long-chain polyPs. The Δvtc4 mutant showed inhibition of Mg2+-dependent phosphate uptake and decreased resistance to alkaline stress but increased tolerance to oxidation and heavy metal ions, especially Mn2+. Quantitative PCR revealed the upregulation of the DDR2 gene implicated in multiple stress responses and downregulation of PHO84 encoding a phosphate and Mn2+ transporter, which could account for the effects on phosphate uptake and Mn2+-related stress response in the Δvtc4 mutant. Our study indicates that short-chain polyPs, plays an important role in the regulation of stress response in yeast.

Background The coronavirus pandemic has led to the creation of clinical guidelines by a large number of professional medical communities. However, the quality and methodology of development of Russian clinical guidelines has been little studied. The continued relevance of studying the use of DOACs in patients with COVID-19 was the basis for conducting this study. Aim The objective of this study was to assess DOACs consumption and expenditures in Russian Federation during COVID-19 pandemic and to analyse domestic evidence base for the use of DOACs in COVID-19 patients through identifying all publicly available Russian-produced CPGs for the treatment of COVID-19 and assessing their quality as the source of recommendations for the use of oral anticoagulants for the prevention of thrombotic complications in COVID-19 patients. Methods We searched Russian databases for CPGs, published between 2020 and 2023. We identified 7 relevant documents that met our inclusion criteria. Three authors analyzed Russian clinical guidelines using a AGREE II questionnaire. We calculated DOACs DDD consumption according to Russian clinical guidelines and DDD consumption in patients with COVID-19 for the period 2020-2022. Results 7 clinical CPGs were analyzed with the AGREE II tool, it was revealed that experts gave the highest scores for the sections scope and purpose (from 62.98% to 100%), clarity of presentation (from 96.30% to 100%). The lowest scores were given for the sections stakenholder involment (33.33% to 64.81%), rigour of development (from 0% to 49.31%), applicability (from 23.61% to 50%), editory independence ( from 0% to 50%). When comparing the total score, it was found that two clinical guidelines received the highest scores - ROPNIZ (Livzan), ROPNIZ (Drapkina). The minimum score is registered with the NIIOZMM (Khripun) clinical guideline. No guideline received a total score of more than 70%. According to clinical recommendations, the consumption of apixaban and rivaroxaban is 15 DDD (30-day course of therapy), 22.5 DDD (45-day course of therapy). Consumption of apixaban in the Russian Federation in 2020 and 2021 corresponds to the indicators presented in clinical recommendations (in 2020 – 26.59 DDD per patient with COVID-19; in 2021 – 15.75 DDD per patient with COVID-19), and in 2022 – 10.67 DDD, which is below the recommended values. In 2020, consumption of rivaroxaban in the Russian Federation was 26.59 which corresponds to data from clinical recommendations; in 2021, consumption decreased to 7.87 DDD; in 2022 – 5.48 DDD, which is 2.74 times less than recommended.

The aim this text to present the confined covariant quark model (CCQM) and review its applications to the decays of B mesons. We do so in the context of existing experimental measurements and theoretical results of other authors, which we review also. The physics principles are in detail exposed for the CCQM, the other results (theoretical and experimental) are surveyed in an enumerative way with comments. We proceed by considering successively three categories of decay processes: leptonic, semileptonic and non-leptonic.

A clinical case of atypical endophthalmitis in an 82-year-old patient who underwent complicated cataract phacoemulsification. Clinical manifestations showed signs of a bacterial process, however, the treatment was not effective. Antifungal therapy had yielded positive results, despite the low probability of a fungal etiology of the process.

Over the last decades, the coated glass products, and especially the low-emissivity coatings have become a common building material used in modern architectural projects. More recently, these material systems became common in specialized glazing systems featuring solar energy harvesting. Apart from achieving the stability of optical parameters in multilayer coatings, it is also important to have improved control over the design of visual color properties of the coated glass. We prepare metal-dielectric composite (MDC) based multilayer thin-film structures using the RF-magnetron sputtering deposition and report on their optical and chromaticity properties in comparison with these obtained using pure metal-based Dielectric/Metal/Dielectric (DMD) trilayer structures of similar compositions. Experimentally achieved Hunter L, a, b values of MDC-based multilayer building blocks of coatings provide a new outlook on the engineering of future-generation optical coatings with better color consistency and developing approaches to broaden the range of achievable color coordinates and better environmental stability.

We report on the study of energy-harvesting performance in medium-size (400 cm²) glass-based semitransparent solar concentrators employing edge-mounted photovoltaic modules. Systems using several different types of glazing system architecture and containing embedded diffractive structures are prepared and characterized. The technological approaches to the rapid manufacture of large-area diffractive elements suitable for use in solar window-type concentrators are described. These elements enable the internal deflection and partial trapping of light inside glass-based concentrator windows. We focus on uncovering the potential of pattern-transfer polymer-based soft lithography for enabling both the improved photon collection probability at solar cell surfaces, and the up-scaling of semitransparent solar window dimensions. Results of photovoltaic characterization of several solar concentrators employing different internal glazing-system structure and diffractive elements produced using different technologies are reported and discussed.

Vit-106 is a promising zirconium-based alloy with high glass-forming ability and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome the size limitations for BMGs because a workpiece is built by the addition of multiple melt portions where the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.

Visualization has always been a crucial part of the educational process. Implementing computer algorithms and virtual reality tools into it is vital for the new generation engineers, scientists and researchers. In the field of chemistry education, various software that allow dynamic molecular building and viewing are currently available. These software are now used to enhance the learning process and ensure better understanding of the chemical processes from the visual perspective. The present short communication provides a summary of these applications based on the NarupaXR program, which is a great educational tool that combines the functionality and simple design necessary for an educational tool. NarupaXR is used with a companion application “Narupa Builder'' which requires a different file format, therefore a converter that allows a simple transition between the two extensions has been developed. The converter sufficiently increases the efficiency of the educational process. The automatic converter is freely available on GitLab (https://gitlab.com/teamSCAMT/converter_mol2_to_xml). The current communication provides detailed written instructions that can simplify the installation process of the converter and facilitate the use of both the software and the hardware of the VR set.

Implementing computer algorithms and virtual reality tools into all areas of the educational process is vital for the new generation engineers, scientists and researchers. With regards to chemistry education, various software that allow dynamic molecular building and viewing are currently available. The present short communication provides a summary of these applications and a detailed description of the NarupaXR program, which has the desired mix of functionality and simple design, necessary for an educational tool. Since NarupaXR can only be used with a companion application “Narupa Builder” which has a different file format, we have developed a converter that allows a simple transition between the two extensions of the aforementioned programs and sufficiently increases the efficiency of the educational process. The automatic converter is freely available on GitLab (https://gitlab.com/teamSCAMT/converter_mol2_to_xml). We have provided this short communication with detailed written instructions that can simplify the installation process of the converter and facilitate the use of both the software and the hardware of the VR set.

Zirconium based bulk metallic glasses are industrially valuable materials which commercial market grows rapidly. Surface modification of these metallic glasses by high-intensity lasers is relatively new and costly treatment promising great advantages over classical surface processing methods. In this work we perform the case study of surface modification of Zr$_{46}$Cu$_{36.8}$Ag$_{9.2}$Al$_8$ metallic glass by high-intensity millisecond laser beam. Our results suggest chemical deposition of atmospheric oxygen and nitrogen in the laser-melted surface area and its surroundings. Zirconium nitride layer was detected in the middle of laser-irradiated area. Nanocrystals embedded in the amorphous matrix were also formed on the surface. Overall, our findings suggest possibilities for improvement of mechanical characteristics of the studied metallic glass.

Towards a better understanding of vegetation, permafrost, climate, landscape and lithology control on major and trace element (including macro and micro-nutrients and toxicants) transport in riverine systems, we studied two medium size (100-150 thousand km² watershed area) pristine rivers (Taz and Ket) of boreal and subarctic zone, western Siberia. Choosing the river basins of very low population density (< 1 people km-²) in the absence of any industrial or agricultural activity allowed testing the sole effect of natural factors and long-range atmospheric transfer on hydrochemistry of riverine solutes during the open water period. In the permafrost-bearing Taz River (main stem and 17 tributaries), sizable control of vegetation on element concentration was revealed. In particular, light coniferous and broadleaf mixed forest controlled DOC, and some nutrients (N, Mn, Fe, Mo, Cd, Ba); deciduous needleleaf forest positively correlated with macronutrients (P, Si, Mg, P, Ca) and Sr, and dark needle-leaf forest impacted Ntot, Al and Rb. Organic C stock in the upper 30-100 cm soil positively correlated with Be, Mn, Co, Mo, Cd, Sb, and Bi. The lithological control was generally poorly pronounced, due to abundant peat deposits overlaying the mineral strata. However, cretaceous carbonate mineral-bearing sedimentary deposits positively impacted the pH and concentration of Si, Mg, Ca and Cs. In the Ket River basin (large right tributary of the Ob River), we revealed the correlations between the phytomass stock at the watershed and alkaline-earth metals and U concentration in the river water. This control was weakly pronounced during high-water period (spring flood) and mostly evidenced during summer low water period.

By reactive DC magnetron sputtering from a pure Ta target onto silicon substrates, Ta(N) films were prepared with a different N₂ flow rate of 0, 12, 17, 25, 38, 58 sccm. The effects of N₂ flow rate on the electrical properties, crystal structure, elemental composition and optical properties of Ta(N) were studied. These properties were characterized by the four-probe method, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and spectroscopic ellipsometry (SE). Results show that the deposition rate decreases with an increase of the N₂ flows. On the other hand, the resistivity increases, the crystal size decreases, and the crystal structure transitions from β-Ta to TaN(111), and finally becomes the N-rich phase Ta₃N₅ (130,040). Studying the optical properties, it is found that there are differences in the refractive index (n) and extinction coefficient (k) of Ta(N) with different thicknesses and different N₂ flow rates, and dependent on the crystal size and crystal phase structure.

The growing interest in heat-conducting nanofluids requires highly sensitive methods for analyzing thermal properties. Thermal-lens spectrometry, despite its advantages over classical methods, does not have a general approach to measuring and interpreting results for dispersed systems. In this paper, by the example of nanofluids of silicon oxide in water in a wide range of concentrations and sizes, the selection of measurement parameters for transient and steady-state thermal lensing is justified, and the interpretation of the results of thermal diffusivity measurements is substantiated. The features of measurements of thermal diffusivity by thermal lens spectrometry under stationary state for dispersed systems are considered. Using this approach, it is possible to detect and distinguish thermal effects with high accuracy. For dispersions of silicon oxide, with increasing concentration, the thermal diffusivity passes through a minimum. Silicon oxide dispersions can be used both as a coolant or as a heat-removing liquid by selecting the particle size and concentration.

This work is devoted to physical vapor deposition synthesis, and characterisation of bismuth and lutetium-substituted ferrite-garnet thin-film materials for magneto-optic (MO) applications. The properties of garnet thin films sputtered using a target of nominal composition type Bi_0.9Lu_1.85Y_0.25Fe_4.0Ga₁O₁₂ are studied. By measuring the optical transmission spectra at room temperature, the optical constants and the accurate film thicknesses can be evaluated using Swanepoel’s envelope method. The refractive index data are found to be matching very closely to these derived from Cauchy’s dispersion formula for the entire spectral range between 300-2500 nm. The optical absorption coefficient and the extinction coefficient data are studied for both the as-deposited and annealed garnet thin-film samples. A new approach is applied for accurately deriving the optical constants data simultaneously with the physical layer thickness, using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method. MO properties, such as specific Faraday rotation, MO figure of merit and MO swing factor are also investigated for several annealed garnet-phase films.

Background: Fullerenes and metallofullerenes can be considered promising nanopharmaceuticals themselves and as a basis for chemical modification. As reactive oxygen species homeostasis plays a vital role in cells, the study of their effect on genes involved in oxidative stress and anti-inflammatory response is of particular importance. Methods: Human fetal lung fibroblasts were incubated with aqueous dispersions of C60, C70, and Gd@C82 in concentrations of 5 nM and 1.5 µM for 1, 3, 24, and 72 hours. Cell viability, intracellular ROS, NOX4, NFκB, PRAR-γ, NRF2, heme oxygenase 1, and NAD(P)H quinone dehydrogenase 1 expression have been studied. Results &amp; conclusion: The aqueous dispersions of C60, C70, and Gd@C82 fullerenes are active participants in ROS homeostasis. Low and high concentrations of AFDs have similar effects. C70 was the most inert substance, C60 was the most active substance. All AFDs have both a “prooxidant” and “antioxidant” effect, but with a different balance. Gd@C82 was a substance with more pronounced antioxidant and anti-inflammatory properties, while C70 had more pronounced “prooxidant” properties.

The flux growth of InVO4 bulk single crystals has been explored for the first time. The reported eutectic composition at a ratio of V2O5:InVO4 = 1:1 could not be used as a self-flux, since no sign of melting was observed up to 1100 °C. Crystals of InVO4 of typical size 0.5×1×7 mm3 were obtained using copper pyrovanadate (Cu2V2O7) as a flux, using Pt crucibles. XRD confirmed the orthorhombic Cmcm structure. Rests of flux material were observed on the sample surface, with occasional traces of Pt indicating some level of reaction with the crucible. X-ray absorption spectroscopy showed that oxidation states of indium and vanadium ions are +3 and +5, respectively. The size and high quality of the obtained InVO4 crystals makes them excellent candidates for the further study of their physical properties.

Non-suicidal self-injurious behavior (NSSI), prevalent in patients with non-psychotic mental disorders (NPMD), is associated with numerous adverse outcomes. Despite active research into the clinical and psychological aspects of NSSI, the underlying biological mechanisms remain obscure. Early adverse experiences are believed to induce long-lasting changes in neuroendocrine mechanisms of stress control playing a key role in NSSI development. The aim of the study was to evaluate parameters potentially predicting development of NSSI in female patients with NPMD. Eighty female patients over 18 years with NPMD and suicidal ideation (40 with and 40 without NSSI) and 48 age matching women without evidence of mental illness (healthy controls) were enrolled. Diagnostic interviews and self-report measures were used to assess childhood maltreatment, presence, frequency, and characteristics of suicidal and self-injurious thoughts and behaviors, the Beck Depression Inventory scale to assess severity of depression. Hypothalamic-pituitary-adrenal axis markers, hormones, and neurotrophic factors were measured in blood serum. The likelihood of developing NSSI in patients with NPMD was associated with early adverse family history and elevated adrenocorticotropic hormone levels. Dysregulation of hypothalamic-pituitary-adrenal axis as a result of early chronic stress experiences may represent critical biological mechanism promoting the development of NSSI behaviors in patients with NPMD.

Meier–Gorlin syndrome (MGS) is a rare genetic developmental disorder that causes primordial proportional dwarfism, microtia, absent or hypoplastic patellae and other skeletal anomalies. Overlapping skeletal symptoms make MGS difficult to diagnose clinically. We describe a 3-year-old boy with short stature, recurrent respiratory infections, short-rib dysplasia, tower head and facial dysmorphisms who was admitted to the Tomsk Genetic Clinic to verify a clinical diagnosis of Jeune syndrome. Clinical Exome sequencing revealed two variants (compound heterozygosity) in the ORC6 gene: c.2T&gt;C(p.Met1Thr) and c.449+5G&gt;A. In silico analysis showed the pathogenicity of these two mutations and predicted a decrease in donor splicing site strength for c.449+5G&gt;A. An in vitro minigene assay demonstrated that variant c.449+5G&gt;A causes a complete skipping of exon 4 in ORC6 gene. The parents asked for urgent prenatal testing for MGS for the next pregnancy, but it ended in a miscarriage. Thus, this case report may help to prevent MGS misdiagnosis in the future. We also performed in silico and functional analyses of ORC6 mutations and developed a restriction fragment length polymorphism and haplotype-based short-tandem-repeat assay for prenatal genetic testing for MGS. These findings should elucidate MGS aetiology and improve the quality of genetic counselling for affected families.

The antioxidant potential (capacity and activity) of aqueous fullerene dispersions (AFD) of non-functionalized C₆₀, C₇₀, and Gd@C₈₂ endofullerene (in micromolar concentration range) was estimated based on chemiluminescence measurements of the model of luminol and generation of organic radicals by 2,2’-azobis(2-amidinopropane) dihydrochloride (ABAP). The antioxidant capacity was estimated by the TRAP method, from the concentration of half-suppression, and from the suppression area in the initial period. All three approaches agree and show that the antioxidant capacity of AFDs increased in the row Gd@C₈₂ < C₇₀ < C₆₀. Mathematical modeling of the long-term kinetics data was used for antioxidant activity estimation. The effect of C₆₀ and C₇₀ is found to be quenching of the excited product of luminol with ABAP-generated radical and not an actual antioxidant effect; quenching constants differ insignificantly. Apart from quenching with a similar constant, the AFD of Gd@C₈₂ exhibits actual antioxidant action. The antioxidant activity in Gd@C₈₂ is 300-fold higher than quenching constants.

Wave steepness is presented as an extension and a valuable add-on to the conventional set of sea state parameters retrieved from satellite altimetry data. Following physical model based on recent advances of weak turbulence theory wave steepness is estimated from directly measured spatial gradient of wave height. In this way the method works with altimetry trajectories rather than with point-wise data. Moreover, in contrast to widely used parametric models this approach provides us with instantaneous values of wave steepness and period. Relevance of single-track estimates of wave steepness (period) is shown for wave climate studies and confirmed by a simple probabilistic model. The approach is verified via comparison against buoy and satellite data including crossover points for standard 1 second data of Ku-band altimeters. High quality of the physical model and robustness of the parametric ones are examined in terms of global wave statistics. Prospects and relevance of both approaches in the ocean wave climate studies are discussed.

Stabilized melanocortin analog peptide ACTH(6-9)PGP (FRWGPGP) possess a wide range of neuroprotective activities. However, its mechanism of action remains poorly understood. In this paper, we studied the pro-proliferative and cytoprotective activity of the adrenocorticotropic hormone fragment 6-9 (FRWG) linked with the peptide Prolyl-Glycyl-Proline on the SH-SY5Y cells in the model of oxidative stress-related toxicity. The peptide dose-dependently protected cells from H2O2, tert-butyl hydroperoxide, and KCN. The mechanism of its action was the modu-lation of proliferation-related (NF-kB and Nrf-2) and antioxidant-related (HO-1, Nqo1, Gclc) genes and apoptosis decrease.

Poplar (Populus) is a genus of woody plants of value for the pulp industry, green energy, urban landscaping, soil phytoremediation and as an ornamental plant. Due to the increasing economic importance of poplar, there is a need to ensure its stable growth by increasing its resistance to pathogens, as one of the main problems in poplar cultivation is its susceptibility to numerous diseases. Currently, breeding poplars with reduced susceptibility to infections is receiving increasing attention. Genetic engineering can produce organisms with improved traits faster than traditional methods, and with the development of CRISPR/Cas-based genome editing systems, scientists have a new highly efficient tool at their disposal to create valuable genotypes. In this review, we summarize recent research data on poplar diseases, the biology of their pathogens, and how these plants resist pathogens. In the final section, we discuss genetic engineering, genome editing, and microbiome strategies that we believe are suitable for obtaining new improved poplar lines.

The electroretinography (ERG) is a diagnostic test that measures the electrical activity of the retina in response to a light stimulus. This test has a long history and has been extensively studied among years. Dr. James Dewar recorded the first electroretinogram signal in 1873. Later he described signal analysis using 4 components, namely amplitude, and latency of a-wave and b-wave. Nowadays, the international electrophysiology community has established the standard for electroretinography in 2008. However, from the point of view of signal analysis, the major change did not happen. ERG analysis is still based on the 4 components evaluation. The article describes ERG database including the classification of signals by using advanced analysis of electroretinograms based on wavelet scalogram processing. To implement an extended analysis of the ERG, the parameters extracted from the wavelet scalogram of the signal were obtained using digital image processing and machine learning methods. The results of the study show that the proposed algorithm implements the classification of adult electroretinogram signals by 19% more accurately and pediatric signals by 20% more accurately than the classical algorithm. The promising use of ERG is differential diagnostics, which may also be used in preclinical toxicology and experimental modeling. The problem of developing methods for electrophysiological signals analysis in ophthalmology is associated with the complex morphological structure of electrophysiological signals components, due to the generation of retina cell electrical responses to light stimulus.

The recent rise in ocean temperatures, accompanied by other environmental changes, has notably increased the occurrence and spread of diseases in Octocorallia, of which many species are integral to shallow tropical and subtropical coral reef ecosystems. This study focuses on the understanding of these diseases, which has been largely limited to symptomatic descriptions, with clear etiological factors identified in only a fraction of cases. A key example is the multifocal purple spots syndrome (MPSS) affecting the common Caribbean octocoral sea fan Gorgonia ventalina, linked to the gall-forming copepods of the genus Sphaerippe, a member of the widespread family Lamippidae. The specialized nature of these copepods as endoparasites in octocorals suggests the potential for the discovery of similar diseases across this host spectrum. Our investigation employed four molecular markers to study disease hotspots in Saint Eustatius, Curaçao, northwest and southwest Cuba, and Bonaire. This led to the discovery of a group of copepod species in these varied Caribbean locations. Importantly, these species are morphologically indistinguishable through traditional methods, challenging established taxonomic approaches. The observed diversity of symbionts, despite the host species' genetic uniformity, is likely due to variations in larval dispersal mechanisms. Our phylogenetic analyses confirmed that the Lamippidae copepods belong to the order Poecilostomatoida (Copepoda) and revealed their sister group relationship with the Anchimolgidae, Rhynchomolgidae, and Xarifiidae clades, known for their symbiotic relationships with scleractinian corals. These results add to our understanding of the evolutionary and ecological interactions of copepods and their hosts, and the diseases they cause, important data in a changing climate.

The evolution of metals micro/nano-structure upon severe plastic deformation (SPD) is still far to be theoretically explained, while experimental datasets are persistently growing for several decades. Major problem associated with understanding of SPD is related to a fact that the latter is a synergetic product of several competing physical effects which alter the material micro/nano-structure. In attempt to find deformational boundaries, where predominantly one mechanism determines the micro/nano-structure, in this paper we propose a continuous piecewise model for the analysis of experiments on material hardness vs strain of SPD processed materials. The novelty of this approach lies in its ability to find, as free-fitting parameters, the strain breakpoints which separate different micro/nano-structure modes generated upon SPD process. The model is applied to analyse experimental data for polycrystalline samples of pure iron and two distinctive strain breakpoints are revealed with good accuracies. This finding is in a good agreement with our earlier results on TEM microscopy studies on pure iron polycrystals after SPD treatment.

The article presents data on phylogeny, genome size, and ploidy of species of the genus Kalidium Moq. in the flora of Kazakhstan. Genus Kalidium belongs to the tribe Salicornieae of the subfamily Salicornioideae of the family Chenopodiaceae and unites 8 species, the main range of which covers the Iranian-Turanian and Central Asian deserts. There are 4 species in the flora of Kazakhstan: K. foliatum, K. caspicum, K. schrenkianum and the recently described K. juniperinum. Populations of species of the genus Kalidium in the saline deserts of Kazakhstan occupy large areas, often forming monodominant communities. Sometimes there is a joint growth of 2 and very rarely 3 species of the genus. During the period of fieldwork (2021-2022), populations were identified in which these species grew together with a predominance, in most cases, of K. caspicum. Samples of representatives from 15 populations were collected for research. Selected plant samples were studied by flow cytometry to determine plant ploidy. Sequencing of nrITS and two chloroplast fragments were used to build a phylogenetic tree, including sequences from the NCBI database., A phylogenetic tree of species of the genus Kalidium was compiled which considers previously published data. In the valley of the middle reaches of the Syrdarya River tetraploid populations of K. caspicum were found. A hybrid between K. foliatum and K. caspicum was found in the Ili River valley (Almaty region, Uigur district). To identify phylogenetic processes at the intraspecific level, the SCoT (Start codon targeted) fingerprinting method was used.