Abstract: NFinFET transistors with fin channel length 90nm and a planar MOSFET transistor with channel length 180nm and 90nm are presented with characteristic curves at various gate biases. A finalized algorithm with kink effects is effectively responsible for addressing the field effect transistors. The algorithm includes the modified conventional current-voltage formula and a nonlinear heat-associated kink solution which is simplified as a Gaussian form. Three parameters in modified model includes kN (related with channel width, channel length, and gate oxide capacitor, and proportional to the mobility of carriers)Vth(Threshold Voltage), and (the inverse of Early Voltage). Those parameters are determined to minimize the discrepancies between the measured data and the fitting values, but leave kinks located at around (VGS－Vth), which are deliberately eliminated by the Gaussian form because of the agitation of thermal kink effects. The whole fitting is made to be as close as the as-measured IDS-VDS. In the mean time, those determined parameters are physically meaningful after the analysis has been done.

The co-occurrence of depression and obesity has become a significant public health concern worldwide. Recent studies have shown that metabolic dysfunction, which is commonly observed in obese individuals and characterized by inflammation, insulin resistance, leptin resistance, and hypertension, is a critical risk factor for depression. This dysfunction may induce structural and functional changes in the brain, ultimately contributing to depression's development. Given that obesity and depression mutually increase each other's risk of development by 50-60%, there is a need for effective interventions that address both conditions. The comorbidity of depression with obesity and metabolic dysregulation is thought to be related to chronic low-grade inflammation, characterized by increased circulating levels of pro-inflammatory cytokines, and C-reactive protein (CRP). As pharmacotherapy fails in at least 30-40% of cases to adequately treat major depressive disorder, a nutritional approach is emerging as a promising alternative. Omega-3 polyunsaturated fatty acids (n-3 PUFAs) are a promising dietary intervention that can reduce inflammatory biomarkers, particularly in patients with high levels of inflammation, including pregnant women with gestational diabetes, patients with type 2 diabetes mellitus, and overweight individuals with major depressive disorder. Further effort directed to implement these strategies in clinical practice could contribute to improved outcomes in patients with depression and comorbid obesity and/or metabolic dysregulation.

Background: In long-term care facilities, there are many residents who do not have the ability to seek shelter by themselves in the case of an emergency. Thus, it is extremely important that the staff of nursing homes are equipped with correct disaster prevention concepts, emergency survival responses, and hazard mitigation measures. Purpose: Discuss the intervention effectiveness of different fire prevention and emergency response trainings at nursing homes and the relationship and predictivity of awareness to self-efficacy. Method: Recruit staff from two nursing homes through purposive sampling, using a two-team pre-and post-test design to collect results from 41 individuals in the experiment group and 40 individuals in the control group. The research tool is the “Nursing Home Fire Prevention and Emergency Response Awareness and Self-Efficacy Scale,” to compare the effectiveness of advanced and general fire safety trainings. Result: After receiving improved advanced fire safety training, the total score and the result of the experiment group on fire prevention and emergency response awareness and self-efficacy had both performed better than the control group who received general fire safety training (p < .001); fire prevention and emergency response awareness has significant and positive correlation with self-efficacy (r=.601, p < .001), and awareness is a significant predictor variable to self-efficacy (p < .001). Conclusion/Practical Application: This study finds that the key to improving learning effectiveness includes adding fire science concept chapter when creating fire safety training material in order to strengthen basic awareness; fire safety training should comprehensively introduce all related duty responsibilities of staff fire defense formation, in turn enabling mutual responsive support for the needs of the site; also, to become familiarized with the knowledge requires appropriate frequency of training and enhancing the staff’s awareness to fire prevention and emergency response, which is the most important key of learning effectiveness.

Owing to their extraordinary properties, carbon-based nanomaterials are gaining traction in biomedicine. Green synthesis is the cost-effective method for fabricating carbon-based nanomaterials due to its rapidity, renewable nature, and sustainability. This study emphasis on the graphene oxide (GO) reduction using a simple one-pot technique that does not require the use of toxic reducing agents. This article reports the green synthesis of reduced graphene oxide (RGO) using Hibiscus sabdariffa L. calyxes extract as the natural reducing agent. Additionally, this article also provides analysis RGO using X-ray diffraction (XRD), UV-Visible spectroscopy (UV-Vis), and Raman spectroscopy. XRD result showed that the GO peak at 11o diminished, and a new hump appear at 22o indicating that the GO is fully reduced when it is refluxed for 6 hours, at 100oC with 1:3 ratio of GO:PE. The UV-Vis data indicated absorption peak of GO (237 nm) and RGO (265 nm) at distinct locations. This finding shed new light on the enormous potential of Hibiscus sabdariffa L. calyxes extract for green GO reduction. As a result, this environmentally friendly method can help reduce dependence on chemical materials.

The universal health insurance system in Taiwan was formed with good intentions to help vulnerable groups. However, the possibility of bankrupting the system due to wasted medical resources. In this study, using the medical expenditures of the Taiwanese Government and gross domestic product (GDP) as variables, the wavelet analysis method was used to empirically study the correlations and leading-lagging relationships in quarterly data in the period from 1996 to 2016. In addition, the dependent population of the insured was used as the control variable. This population had no income and had high medical demands. Results: After the dependent population was included as a control variable, there was a period of low-frequency (one to four years short-term) linkage correlation, as well as a period of high-frequency (four to eight years long-term) linkage correlation. In addition, for more than eight years, there was also a high degree of linkage correlation, indicating that the linkage between medical expenditures and GDP occurred over the long term. Moreover, since medical expenditures positively affected GDP, one-way causality was observed. However, after 2008, regardless of whether a long or short term was examined, there was almost no linkage correlation. Before 2008, the medical expenditures of the government were positively correlated with economic growth; i.e., they enhanced economic growth. But, after 2008, this effect had already disappeared. The universal health insurance system has long been denounced as a waste of medical resources, and the waste must be immediately stopped. The government urgently needs to find a new solution.

The increased consumption of high fat-containing foods has been linked to the prevalence of obesity and abnormal metabolic syndromes. Rhizopus oligosporus, a fungus in the family Mucoraceae, is widely used as a starter for homemade tempeh. Although R. oligosporus can prevent the growth of other microorganisms, it grows well with lactic acid bacteria (LAB). Lactobacillus plantarum can produce β-glucosidase, which catalyzes the hydrolysis of glucoside isoflavones into aglycones (with greater bioavailability). Therefore, the development of a soybean-based functional food by the co-inoculation of R. oligosporus and L. plantarum is a promising approach to increase the bioactivity of tempeh. In this study, the ameliorative effect of L. plantarum in soy tempeh on abnormal carbohydrate metabolism in high-fat diet (HFD)-induced hyperglycemic rats was evaluated. The co-incubation of L. plantarum with R. oligosporus during soy tempeh fermentation reduced the homeostatic model assessment of insulin resistance, HbA1c, serum glucose, total cholesterol, triglyceride, free fatty acid, insulin, and low-density lipoprotein contents and significantly increased the high-density lipoprotein content in HFD rats. It also increased the LAB counts as well as the bile acid, cholesterol, triglyceride, and short-chain fatty acid contents in the feces of HFD rats. Our results suggested that the modulation of serum glucose and lipid levels by LAB occurs via alterations in the internal microbiota, leading to the inhibition of cholesterol synthesis and promotion of lipolysis. Tempeh, produced with both L. plantarum and R. oligosporus, may be a beneficial dietary supplement for individuals with abnormal carbohydrate metabolism.

Background: Cancer patients require cross-professional care during the diagnosis and treatment periods. Therefore, methods for effectively carrying out case management are essential to tumor care. Purpose: To investigate the effects of using the community software LINE Official Ac-count on oral cancer case management. Methods: An experimental design was used; 100 patients were randomly divided into two groups by using a computer-generated random number table. The experimental group used LINE Official Account, which gave them self-care information, timely messages, and one-on-one health-care consultations. The control group followed standard healthcare practices. Results: The experimental group was satisfied with the self-care information provided by LINE Official Account (86.9%), patients regularly checked the self-care information (89.4%) and would check the information when receiving a push notification (54.3%). Ten patients used the one-on-one consultation(20.0%). LINE Official Account had a significant effect on the rate of participation in support groups. Generalized estimating equations indicated a significant difference between the two groups regarding the overall quality of life over 7 days (P = 0.023). Conclusion: Community software applications used in oncological case management can improve self-management and empower, also enable tracking of long-term follow-up effectiveness and reinforce the case manager’s role as a family therapist. Therefore, this study recommends that case manager systems be incorporated into mobile applications to increase the sustainable management, accessibility, effectiveness, and satisfaction of oncological management systems. This study also provides the value of Sustainable Development Goals (SDGs) with Good Health and Well-being, and decreased social withdrawal among patients with oral cancer.

Traditional Chinese medicine requires decoction and consumption, which is time-consuming and labor-intensive. Scientific Chinese medicine (SCM), on the other hand, uses concentrated granules that can be taken with hot water, making it widely welcomed. With the widespread adoption of SCM, the packaging technology has started to receive attention. Whether it is manpower allocation, operation time, or the uniformity and residue of the medicine powder, these factors can become bottlenecks in the process. A traditional SCM pharmacy machine is purely mechanically hardwired. This paper proposes SCMtalk, an Internet of Things (IoT)-based SCM mechanism designed to enhance the efficiency and accuracy of SCM medicine packets generation. We show how SCMtalk develops IoT hardware and software modules for medicine selection, mixing, dispensing, packaging, and cleaning. We also explain how the mechanical IoT hardware is integrated with the corresponding software module to become an individual IoT device. These IoT devices can be transparently replaced, allowing us to easily upgrade the individual components of the SCM packet generation through the IoT concept. Finally, we address quality control issues by leveraging IoT. One contribution of this paper is to introduce an interesting SCM application to IoT experts and to demonstrate how we collaborated with pharmacists and mechanical experts to use a powerful IoT platform to create a smart pharmacy.

Pain is unpleasant sensory and emotional experience accompanied by tissue injury. Often an indi-vidual experience, it can be influenced by different physiological, psychological, and social factors. Fibromyalgia, one of the most difficult-to-treat types of pain, is characterized by general muscle pain accompanied by obesity, fatigue, sleep, and memory and psychological concerns. Fibromyal-gia has increased nociceptive sensations via central sensitization in the brain and spinal cord level. We used intermittent cold stress to create a mouse fibromyalgia pain model (Day 0: 3.69  0.14 g; Day 5: 2.13  0.12 g). Mechanical pain could be reversed by eicosapentaenoic acid (EPA) admin-istration (Day 0: 3.72  0.14 g; Day 5: 3.69  0.13 g). A similar trend could be also observed for thermal hyperalgesia. The levels of elements in the transient receptor potential V1 (TRPV1) sig-naling pathway were increased in the ascending pain pathway, including the thalamus, medial prefrontal cortex, somatosensory cortex, anterior cingulate cortex, and cerebellum. EPA intake significantly attenuated this overexpression. Novel chemogenetics method was used to indeed in-hibit SSC to ACC activity presented an analgesic effect through TRPV1 downstream pathway. The present results provide insights as to the role of TRPV1 signaling pathway as in fibromyalgia and its potential as a clinical target.

Neuropathic pain is initiated by a malfunction of the somatosensory cortex system. Acupuncture had been shown to have therapeutic effects for neuropathic pain, although with uncertain mechanisms. We used electroacupuncture (EA) to treat mice spared nerve injury (SNI) model and explore the underlying molecular mechanisms through novel chemogenetic techniques. Both me-chanical and thermal pain were found in SNI mice till four weeks (mechanical: 3.23 ± 0.29 g; thermal: 4.9 ± 0.14 s). Hyperalgesia was attenuated by 2 Hz EA (mechanical: 4.05 ± 0.19 g; ther-mal: 6.22 ± 0.26 s) but not with sham EA (mechanical: 3.13 ± 0.23 g; thermal: 4.58 ± 0.37 s), sug-gesting EA’s specificity. In addition, animals with transient receptor potential V1 (Trpv1) deletion showed no significant induction of neuropathic pain (mechanical: 4.43 ± 0.26 g; thermal: 6.24 ± 0.09 s). Moreover, we found increased levels of inflammatory factors such as interleukin-1 beta (IL1-β), IL-3, IL-6, IL-12, IL-17, tumor necrosis factor alpha, and interferon gamma after SNI modeling, which decreased in EA and Trpv1-/- group rather than sham group. Western blot and immunofluorescence analysis showed similar tendency in the dorsal root ganglion, spinal cord dorsal horn, somatosensory cortex (SSC), and anterior cingulate cortex (ACC). In addition, a novel chemogenetics method was used to precisely inhibit SSC to ACC activity showed an analgesic effect through TRPV1 pathway. In summary, our findings indicate a novel mechanism underlying neuropathic pain as beneficial targets for neuropathic pain.

This paper takes the VR animation display of the Ming Xiao Mausoleum General stone statue life as an example to study the advantages of VR animation in the display of material heritage. Combined with literature and pictures, the digital restoration of the Ming Xiao Mausoleum stone statue is carried out in MAYA and Z brush, and the construction of the scene and the output of the final effect are realized in UE4.

Programmed cell death 4 (Pdcd4) is a tumor suppressor, which has been demonstrated to efficiently suppress tumorigenesis. Biochemically, Pdcd4 binds with translation initiation factor 4A and represses protein translation. Beyond its role in tumor suppression, increasing evidence indicates that Pdcd4 enhances the chemosensitivity of several chemotherapeutic drugs. To date, several translational targets of Pdcd4 have been identified. These targets govern important signal transduction pathways, and their attenuation may enhance chemosensitivity or overcome drug resistance. This review will discuss the signal transduction pathways regulated by Pdcd4 and the potential mechanisms through which Pdcd4 enhances chemosensitivity or counteracts drug resistance.

Is there any possible synergic effect of fertility outcome between spindle view-assisted intracyto-plasmic sperm injection (SV-ICSI) with or without assisted oocyte activation (AOA) for patients with low fertilization rate history? To explore the answer, a retrospective study was held in our fertility center by reviewing patients receiving SV-ICSI during 2019/03 to 2023/06. Total 47 pa-tients were included, the fertility outcomes of intervention group (AOA-SV-ICSI, 14 patients) and control group (SV-ICSI, 33 patients), such as fertilization rate, blastocyst formation rate and clin-ical pregnancy rate, were analyzed. The blastocyst formation rate between groups was signifi-cantly higher in AOA-SV-ICSI group (p=0.020), but the fertilization rate and clinical pregnancy rate did not reach any statistical significance. This discovery of increased blastocyst formation rate in low fertilization rate patients could possibly help them in getting more usable embryos in fertility treatment.

Graphene is a remarkable material with numerous applications. Due to its thin and lightweight design, it is ideal for a variety of applications. The synthesis of high-quality graphene in a cost-effective and environmentally friendly manner continues to be a significant challenge. Chemical reduction is considered to be the most advantageous method for preparing reduced graphene oxide (rGO). However, this process necessitates the use of toxic and harmful substances, which can have a detrimental effect on the environment and human health. Thus, to accomplish the objective, the green synthesis principle has prompted researchers worldwide to develop a simple method for green reduction of graphene oxide (GO), which is readily accessible, sustainable, economical, renewable, and environmentally friendly in nature. For example, the use of natural materials such as plants is generally considered safe. Furthermore, plants contain reducing and capping agents. The current review will focus on the discovery and application of rGO synthesis using extracts from a variety of different parts of the plant. The review aims to aid current and future researchers in their search for a novel plant extract that acts as a reductant in the green synthesis of rGO. The review aims to assist current and future researchers in their research for a novel plant extract that acts as a reductant in the green synthesis of rGO as well as their potential applications in a variety of industries.

This research used an experimental study design in which 60 subjects were randomly assigned to either an experimental (image e-book guidance) group or a control (text guidance) group after meeting the admission conditions and agreeing to participate in the study. It was proven that providing image e-book guidance before surgery significantly changed the behavior of patients and promoted relief of urinary catheter discomfort through self-efficacy to reduce urinary catheter pain after surgery. It was found that providing image e-book guidance can shorten the time for health education and provide patients with repeated medical education and familiarity with health guidance, which can help to address the important clinical service demand issue and the shortage of nursing staff.

Background and Objectives: Treatment for antineutrophil cytoplasmic antibody-associated vasculitis (AAV) must deal with immunosuppression as well as infections associated with compromised immune system, such as tuberculosis (TB). Our aim was to overcome the gap in the literature concerning the risk of incidental TB after diagnosis of AAV. Materials and Methods: This retrospective population-based cohort study was based on the data from the National Health Insurance Research Database in Taiwan. We used a novel algorithm to identify patients with newly diagnosed granulomatous polyangiitis (GPA) or microscopic polyangiitis (MPA) between January 1, 2000 and December 31, 2012. The primary outcome was risk of incidental TB. Cox proportional hazard models were used to evaluate the association between AAV and incidental TB. Results: A total of 2,257 patients with AAV and a propensity-score matched cohort of 9,028 patients were studied. Overall, patients with AAV were at a 1.48x higher risk of contracting incidental TB than were patients in the matched cohort (adjusted HR 1.48; 95% confidence interval [CI], 1.02-2.15). Note that the highest risk of contracting incidental TB was in the first two years following a diagnosis of AAV, with a nearly 1-fold increase in risk (adjusted HR, 1.91; 95% CI, 1.01-3.60). Female AAV patients were 3.24x more likely than females without AAV to develop TB (adjusted HR 3.24; 95%CI, 1.85-5.67). Conclusion: Patients with AAV face an elevated risk of contracting incidental TB, particularly within the first two years after AAV diagnosis. The risk of contracting TB is higher among female AAV patients than among females without AAV.

The value of an NBA basketball player varies at each crucial point in time, depending on the player’s career and performance. This study constructs a player’s value assessment model. The model comprises two parts. First, from an objective perspective, entropy is employed to measure each player’s achievement in five categories—rebounds, assists, steals, blocked shots, and scores. The total entropy assessment value is calculated and then combined with the players’ scores to develop a player's value matrix to assess the relative value model among players of the same type.

Utilizing relational networking and cultural assets provide an arena for village development associations (VDAs) to fill the gaps in infrastructure in resource limited communities of Cameroon’s north-western region. Through case study, this study interrogates the foundational thesis of relational networking and cultural assets deployed to deal with social development challenges. Semi-structured interviews were undertaken with community participants. Purposive sampling was used, and data were analysed and critically synthesized with comparable literature. Communities increasingly shoulder their own development through a multiplicity of agency with internal and external stakeholders. The analysis captures a typology of incremental cultural assets, galvanised and re-engineered, promoting a rejuvenated community. A multi-layered approach centred on intersecting elements with unvarying input from community members are perceptible. Though the translational benefits are not clear-cut, relational networking and incremental cultural assets hold out the prospect for community transformation in infrastructure provision - supply of fresh water, equipping schools, community halls, building roads, bridges and community halls. In the process, social inequality and other barriers of disadvantage are narrowed.

A new type of gold nanoparticles was synthesized by using benzoyl pyrazolone as a capping agent. The synthesized AuNPs exhibited a spherical shape and a monodisperse and fluorescence emission characteristic peak at 650 nm. The AuNPs –BMPBP was demonstrated as sensitive and selective fluorescent chemosensor for detection of Al ³⁺ ion. In the presence of Al ³⁺ ion, the fluorescent emission of BMPBP-AuNPs at 650 nm, increased with an increasing concentration of Al ³⁺ ion with a low detection limit (2 µM), the proposed method provided to apply determination of Al ³⁺ ion of tap water with satisfactory results.

Today, the various abilities that nurses require to meet patients’ healthcare needs adequately are all affected by AI-enabled systems. This research used an experimental study design in which 60 subjects were randomly assigned to either an experimental (AI image e-book guidance) group or a control (text paper guidance) group after meeting the admission conditions and agreeing to participate in the study. It was proven that providing AI image e-book guidance before surgery significantly changed the behavior of patients and promoted relief of urinary catheter discomfort through self-efficacy to reduce urinary catheter pain after surgery(p=0.000). It was found that providing AI image e-book guidance can shorten the time for health education and provide patients with repeated medical education and familiarity with health guidance, which can help to address the important clinical service demand issue and the shortage of nursing staff.

Ming-style round-backed armchairs as a classic Chinese chair design are renowned for the blend of ergonomics, practicality, and elegance. Although the Chinese armchair furniture industry has made strides in sustainability, there is still a need for further improvements in material selection, manufacturing processes, and supply chain management to fully support the development of sustainable furniture. Laminated bamboo lumber as new sustainable materials are becoming a popular option for furniture designers in the era of "sustainable design". This research aims to investigate the feasibility and application of laminated bamboo lumber in the design of Chinese armchair furniture and proposes innovative ideas for optimizing the armchair's design. First, an empirical study was conducted to comprehensively understand the classification of Ming-style round-backed armchairs’ structure to develop a 3D model. Secondly, an experimental research method was then employed to explore the parameters of laminated bamboo lumber for future studies. Additionally, a validation experiment was conducted to compare real-world scenarios with simulations using finite element analysis in Ansys. Finally, finite element analysis was used to test the feasibility and application of laminated bamboo lumber in furniture design, focusing on the material’s mechanical properties. Results indicated that laminated bamboo lumber has excellent mechanical properties as furniture design materials, subsequently, using the optimized results, the use of 0.6319 kg of steel was successfully reduced by 23.68% to ensure the armchair’s stability. This provides a reference for the future compter-assist and standardized innovative design of Chinese armchair. By incorporating compter-assist design and lightweight optimization, it is possible to save materials and make more efficient use of resources, thereby contributing to sustainable development goals in the field of furniture design.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

Transition metal dichalcogenides (TMDs) monolayers exhibit unique valleytronics properties due to the dependency of the coupled valley and spin state at the hexagonal corner of the first Brillouin zone. Precisely controlling valley spin-polarization via manipulating the electron population enables its application in valley-based memory or quantum technologies. This study uncovered the uncompensated spins of the antiferromagnetic oxide (NiO) serving as the ferromagnetic (FM) order to induce valley spin-polarization in molybdenum disulfide (MoS₂) monolayers via the magnetic proximity effect (MPE). A spin-resolved photoluminescence spectroscopy (SR-PL) was employed to observe MoS₂, where the spin-polarized trions appear to be responsible for the MPE, leading to a valley magnetism. Results indicate that local FM order from the uncompensated surface of NiO could successfully induce significant valley spin-polarization in MoS₂ with the depolarization temperature approximately at 100 K, which is relatively high compared to related literature. This study reveals new perspectives and potential of AFM materials in the field of exchange-coupled van der Waals heterostructures.

Anti-interferon (IFN)-γ autoantibodies are linked to varicella-zoster virus (VZV) infection. Given the elevated risks of herpes zoster (HZ) in rheumatoid arthritis (RA) patients treated with Janus kinase inhibitors (JAKi), we aimed to examine the relationship between anti-IFN-γ autoantibodies with HZ development in JAKi-treated patients. In twenty-four RA patients with new-onset HZ and forty-two without HZ, serum titers of anti-IFN-γ autoantibodies, plasma levels of IFN-γ, monocyte chemoattractant protein-1 (MCP-1), and IFN-γ inducible protein-10 (IP-10) were measured by ELISA. Significantly lower MCP-1 levels were observed in patients with HZ compared to those without (median, 98.21pg/ml, interquartile range (IQR) 77.63-150.30pg/ml versus 142.3pg/ml, IQR 106.7-175.6pg/ml, p&lt;0.05). There was no significant difference in anti-IFN-γ titers, IFN-γ levels, or IP-10 levels between patients with and without HZ. Three of 24 patients with HZ had severe HZ with multi-dermatomal involvement. Anti-IFN-γ titers were significantly higher in patients with severe HZ than in those with non-severe HZ (median 24.8ng/ml, IQR 21.0-38.2ng/ml versus 10.5ng/ml, IQR 9.9-15.0ng/ml, p&lt;0.005). In conclusion, patients with HZ had significantly lower MCP-1 levels than those without HZ, and patients with severe HZ had significantly higher titers of anti-IFN-γ than those with non-severe HZ. Given small sample size, our results need further validation in future studies.

The detection of Fasciola eggs in ruminant fecal samples typically occurs around 15 weeks post-infection during patent infections. The recent introduction of coproantigen ELISA (cELISA) diagnostics, which capture antigenic enzymes in fecal material, holds promise for monitoring Fasciola fecal egg count (FFEC) to implement control programs, particularly targeted treatments. This study compared two study groups, those with positive FFEC (FFEC+ve) and negative FFEC (FFEC-ve), to assess the sensitivity of Flukefinder sedimentation and a cELISA kit. This study reports that the coproantigen ELISA detection limit was 4.5 eggs per gram (epg) for a 100% positivity rate. Additionally, a moderate, statistically significant positive correlation (r²=0.716, p-value < 0.01) and an odds ratio of 1.96 (p-value < 0.01) were observed between FFEC and Fasciola coproantigen from cELISA. This implies that for every single unit increase in FFEC, there is a 96% likelihood of obtaining a higher optical density (OD) reading from the cELISA test. The results suggest that cELISA can complement fecal sedimentation tests, serving as a valuable tool for detecting cattle with high FFEC. This capability facilitates targeted treatment strategies, thereby aiding in the control and prevention of the spread of fasciolosis within the studied area.

HAX1 is a multifunctional protein involved in the antagonism of apoptosis in cellular response to oxidative stress. In the present study we identified HAX1 as novel binding partner for Che-1/AATF, a pro-survival factor which plays a crucial role in fundamental processes, including response to multiple stresses and apoptosis. HAX1 and Che-1 proteins show extensive colocalization in mitochondria and we demonstrated that their association is strengthened after oxidative stress stimuli. Interestingly, in MCF-7 cells, resembling luminal estrogen receptor (ER) positive breast cancer, we found that Che-1 depletion correlates with decreased HAX1 mRNA and protein levels, and this event is not significantly affected by oxidative stress induction. Furthermore, we observed an enhancement of the previously reported interaction between HAX1 and estrogen receptor alpha (ERα) upon H2O2 treatment. These results indicate the two anti-apoptotic proteins HAX1 and Che-1 as coordinated players in cellular response to oxidative stress with a potential role in estrogen sensitive breast cancer cells.

Change orders have received considerable attention from researchers thus far, but none have considered pricing strategies of change orders through the interaction between general contractors and subcontractors. Previous studies found that contractors’ opportunistic bidding considering beyond-contractual reward (BCR) in the execution stage can be reduced by improving the construction management system and strengthening the supervision of contractors’ performance. However, the BCR remains in ecology of construction engineering. This study proposes an integrated evolutionary game theory-system dynamics model (ET-SD model) and simulates the pricing strategy of change orders between general contractors and subcontractors to explore the root cause of BCR phenomenon. Sensitivity analysis on the evolutionary dynamics of payoff is explored. Results reveal that change orders with BCR maintain Nash equilibrium and evolutionary stable strategy (ESS) unless changing the payoff structure between general and subcontractors’ pricing strategies. This study presents important managerial insights from the evolutionary game perspectives, nature of change orders, and payoff of the alternative.

This project designed a set of network security mechanisms for cloud applications in VANETs. At present, cloud computing is one of the government’s development priorities in the industry. We divide cloud into public, private, and hybrid clouds in this project. Vehicles or passengers can access road conditions or public transport information through the public cloud; public transportation can access current driving records and users can access relevant enterprise information on the private cloud and hybrid cloud is a combination of public and private clouds. Both cloud computing or VANETs require network and information security. At present, many researches on VANETs security only focus on message communication, and neglect information storage. Researches on cloud computing security only focus on information protection, and neglect user privacy and anonymity. This project designed a set of network and information security mechanisms in line with the requirements of Confidentiality, Authentication, Non-repudiation, Conditional Anonymity, and Conditional Untraceability. This project primarily needs to achieve the following: 1.an authentication mechanism to verify the identity of each other between the passenger and the vehicle and to verify the identity with Single Sign-On; 2. vehicle or user privacy and anonymity, which need to be able to replace the anonymous ID and related parameters for the vehicle or the user; 3. a private communication mechanism, which enables any vehicle or user to communicate privately; and 4. an information security encryption method, which can encrypt the information on a cloud server to avoid unauthorized access by internal personnel or hackers.

AI-driven tools can identify nursing students' strengths and weaknesses, thus enabling the development of customized learning plans that target specific areas for improvement. This targeted approach can enhance knowledge retention and skill development, resulting in better prepared healthcare professionals. Nursing students are required to overcome their own psychological stress during their internship in order to understand sick children’s emotional reactions, as well as to be able to interact and communicate with such children. The application of AI picture-based teaching e-books helps nursing students to understand how to use therapeutic games to improve communication with sick children. A comparison of the differences between nursing teachers’ self-efficacy scores and nursing students’ application of AI picture-based teaching e-books (experimental group) and narrative handouts (control group) was achieved via therapeutic games to deal with sick children’s fear of medical examinations and treatments. In addition, a comparison was also conducted on the differences between the impact of the self-efficacy of the experimental group and that of the control group in dealing with sick children’s behavioral responses with respect to fears of medical examinations and treatments. This study is a quasi-experimental study, in which the self-efficacy scores of 30 nursing students were collected and analyzed in both the experimental group and the control group before and after intervention in dealing with sick children’s behavioral responses to fears of medical examinations and treatments. It was found that the self-efficacy score of the experimental group was higher than that of the control group (β coefficient is 0.356) when assessing the self-efficacy scores and behavior of the experimental and control groups in dealing with sick children’s fears of medical examinations and treatments through one-way analysis of covariance (one-way ANCOVA), moreover, a statistically significant difference (p < 0.05) was observed. The experimental group’s score of behavioral responses to the fears of sick children to examinations and treatments was lower than that of the control group (β coefficient was -1.540), wherein a statistically significant difference (p < 0.05) was shown. The self-efficacy of the experimental group in dealing with sick children’s fears of medical examinations and treatments had a statistically significant impact on the sick children’s behavioral responses to the fear of medical examinations and treatments (p < 0.05). In addition, the higher the self-efficacy scores of the experimental group in dealing with sick children’s fear of medical examinations and treatments, the lower the sick children’s behavioral responses to fears of medical examinations and treatments (the β coefficient was -0.914), the control group’s self-efficacy scores in dealing with sick children’s fears of medical examinations and treatments did not have a statistically significant impact on the sick children’s behavioral responses to fears of medical examinations and treatments (p > 0.05). This study proves that the application of AI picture-based teaching e-books by nursing teachers is more effective than narrative handouts in improving nursing students’ self-efficacy when using therapeutic games to deal with, as well as reduce, sick children’s fears of medical examinations and treatments.

Biofilms are complex communities of microorganisms that adhere to surfaces and develop a protective matrix. The colonization of devices in the food and health care industries by microbial biofilms poses numerous risks. Existing antimicrobial agents often fail to penetrate the biofilm matrix, allowing the pathogen to grow and persist. The objective of this study was to evaluate the impact of MADIO PRO+ multipurpose disinfectant on Salmonella Typhimurium biofilm using crystal violet assay and FTIR spectroscopy. Results demonstrated that MADIO PRO+ multipurpose disinfectant significantly (p<0.05) inhibited biomass of S. Typhimurium biofilm and altered the structure of S. Typhimurium biofilm. In conclusion, MADIO PRO+ multipurpose disinfectant offers an advantage in biofilm control strategy. This discovery could help the food and health care industries to plan better microbial intervention strategies.

Construction productivity entails a wide range of work combinations. When human resources are scarce, it is critical to replace manpower with machinery, and calculating machinery productivity is crucial. Traditional labor productivity methods, however, cannot address dredging complex multi-attribute decision-making (MADM) problems. Aiming to address the limitations of the traditional labor productivity method, this paper extends the data envelopment analysis (DEA) and proposes a new dredging productivity evaluation method. The proposed method can solve the problem of evaluating various combinations of factors (single-input, multiple-input, sin-gle-output, and multiple-output) and the problem suggesting that the efficiency of the DEA method'scalculation results is equal to 1. The effectiveness of the proposed method was verified using reservoir dredging examples. The simulation results show that the proposed method has broad applicability, can accurately evaluate the related dredging performance issues, and provide directions for construction managers to improve labor productivity.

This paper aims to build up a preference function to evaluate the public benefits of the type of agricultural farming, biodiversity, water provisions, land use type, ecotourism modes, and a monetary attribute (environmental trust fund and willingness to contribute) associated with an ecosystem service and land use program in a forest park. This study used the choice experiments to build a random utility model, analyze the average preference for the above land use attributes based on the conditional logit and used a latent class model to test the resident’s heterogeneous preferences for land use planning in the forest park. We also estimated the welfare derived from various land use programs. The empirical result had shown that: (1) increasing organic farming area, maintaining the status quo of species biodiversity, increasing the surface water provision, increasing the area of custom flora, increasing the wetland area, and setting up an integrated framework for ecotourism increase the public’s preference for the land use program; (2) we found that farmer and non-farmer haven’t the same land use preferences; (3) the ecotourism development program incorporating biodiversity, organic farming, ethnobotany, and wetland area with integrated ecotourism are more preferred than other land use program scenarios.

No research to date has explored the possibility of context-specific, within-relationship fluctuation in attachment security. In this present article, two cross-sectional studies were designed (1) to develop and validate context-specific attachment scales in Traditional-Chinese, and (2) to explore fluctuations in within-parent attachment security between the contexts of sport and academics, in relation to global attachment patterns and indicators of psychological wellbeing. Results indicated that youth can and do perceive within-parent attachment patterns differently depending upon context but that the relationship of such differences to context-specific outcomes is complex. Of particular interest was that the degree of within-parent attachment variability between contexts was clearly and negatively related to indices of psychological wellbeing. This suggests that contextual variation may be a meaningful and useful way to explore within-parent attachment fluctuation.

This study aims to exploit the distinctive properties of carbon nanotube materials, which are particularly pronounced at the microscopic scale, by deploying fabrication techniques that allow their features to be observed macroscopically. Specifically, we aim to create a semiconductor device that exhibits flexibility and the ability to modulate its electromagnetic wave absorption frequency by means of biasing. Initially, we fabricate a sheet of carbon nanotubes through a vacuum filtration process. Subsequently, phosphorus and boron elements are separately doped into the nanotube sheet, enabling it to embody the characteristics of a PN diode. Measurements indicate that, in addition to the fundamental diode's current-voltage relationship, the device also demonstrates intriguing transmission properties under the TEM mode of electromagnetic waves. It exhibits a frequency shift of approximately 2.3125 GHz for each volt of bias change. The final result is a lightweight and flexible carbon-based semiconductor microwave filter, which can conform to curved surfaces. This feat underscores the potential of such materials for innovative and effective electromagnetic wave manipulation.

This is a survey study that dialysis patients were randomly sampled from a medical center in northern Taiwan, and those who gave their consent to participate were included in this study. The purpose of this study was to explore the correlation between depression, hope, and quality of life of dialysis patients. All subjects agreed to take "Beck’s Depression Inventory", " The Chinese version of Herth Hope Index" and " The Chinese version of Kidney Disease Quality of Life" (KDQOL-SFTM). Data were processed using SPSS for descriptive and inferential statistics. The results showed that patients were 12.45±SD 9.03, which was mild depression, the mean score of hope was 34.25, which was equivalent to 72.60%, and was at the middle level. In KDQOL-SFTM, the score in mental composite (M=42.65, SD=8.81) was higher than in physical composite (M=37.38, SD=9.28), and the score was at the intermediate quality of life, and hope and depression were significantly and negatively correlated. This study suggests that dialysis case managers provide nursing guidance to help dialysis patients learn comfortable care methods and support the resilience they need.

Taiwan is the world’s leading country regarding tuna longline fisheries; the combined catches with those from Japan account for more than half of the global total. However, the bycatch of sea turtles, seabirds, and dolphins in longline fisheries has attracted international concern. Regarding sea turtle conservation, the use of circle hooks in longline fisheries will inevitably become a trend. Meanwhile, Taiwanese fishermen are concerned whether the use of circle hooks will have a negative impact on the catch efficiency of target species. This study was conducted to compare the catch efficiency of circle and tuna hooks by the Taiwanese commercial tuna longline fishing vessels in the eastern Pacific Ocean. The results indicated that if the effects of immersion time were considered, the catch rates of all groups were the same between 4.2-sun circle and tuna hooks. However, the catch rate of 4.0-sun circle hooks was significantly higher than the two types of 4.2-sun circle and tuna hooks. Regarding survival rates, fish caught with circle hooks showed higher survival rates than tuna hooks for total commercial fish, tunas and yellowfin tuna (Thunnus albacares). However, the survival rate was only determined at haulback; the relationship between survival rate and immersion time still needs further investigation. Regarding catch sizes, there were no significant differences in the sizes of bigeye (Thunnus obesus) and yellowfin tuna between circle and tuna hooks. But based solely on mean weight, the value of yellowfin tuna caught using circle hooks may be higher than those using tuna hooks. In summary, the circle hooks used in this study did not show a negative impact on the catch efficiency of Taiwanese longline fisheries, and could show a superior performance than that of tuna hooks. These results could be actively promoted in the industry through the education and training of fishermen; thus enabling Taiwan to comply with international sea turtle conservation trends.

Background/Objectives: Different approaches are required in treating patients with multiple pulmonary lesions. A multistage procedure may increase the risk of complications and patient discomfort. This study provides an initial experience with single-stage management of multiple lung lesions using percutaneous ablation with thoracoscopic resection in a hybrid operating room (HOR). Methods: We retrospectively evaluated patients who underwent combined ablation and resection in a HOR between May 2022 and July 2024. All patients received a single anesthesia via endotracheal tube intubation. Clinical data, operative findings, and pathological characteristics of the lung nodules were recorded. Results: A total of 23 patients were enrolled in this study. Twenty patients underwent unilateral procedures, and the other three patients underwent bilateral procedures. Ablations were performed before lung resection in 22 patients; only one patient underwent surgery first. The median global operating room time was 227.0 min. The median total radiation dose (dose area product) was 14076 μGym2. The median hospital postoperative length of stay was 2 days. Conclusion: The single-stage procedure of percutaneous ablation with thoracoscopic resection under general anesthesia in a HOR is feasible and safe. This procedure is an alternative method for managing multiple pulmonary lesions.

We propose a novel protocol to build a maximally entangled state based on controlled-not (CNOT) gates. In particular, we give detailed steps to construct maximally entangled state for 4-, 5-, and 6-qubit systems. The advantage of our method is the simple algebraic structure which can be realized via current experimental technology.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

To quantify damage to reinforced concrete (RC) column members after an earthquake, an engineer needs to know the maximum applied force that was generated by the earthquake. Therefore, in this work, piezoceramic transducers are used to detect the applied force on an RC column member under dynamic loading. To investigate the use of post-embedded piezoceramic sensors in detecting the force that is applied to RC columns, eight full-size RC column specimens with various failure modes are tested under specific earthquake loadings. Post-embedded piezoceramic sensors are installed at a range of depths (70-80 mm) beneath the surface of a column specimen to examine the relationship between the signals that are obtained from them and the force applied by the dynamic actuator. The signals that are generated by the post-embedded piezoceramic sensors, which correlate with the applied force, are presented. These results indicate that the post-embedded piezoceramic sensors have great potential as tools for measuring the maximum applied force on an RC column in an earthquake. Restated, signals that are obtained from post-embedded piezoceramic sensors on an RC column in an earthquake can be used to determine the applied force and corresponding damage or residual seismic capacity.

An automated discharge imaging system (ADIS), a non-intrusive and safe approach, was developed for measuring river flows during flash flood events. ADIS consists of dual cameras to capture complete surface images in the near and far fields. Surface velocities are accurately measured using the Large Scale Particle Image Velocimetry (LSPIV) technique. The stream discharges are then obtained from the depth-averaged velocity (based upon an empirical velocity-index relationship) and cross-section area. The ADIS was deployed at the Yu-Feng gauging station in Shimen Reservoir upper catchment, northern Taiwan. For a rigorous validation, surface velocity measurements were conducted using ADIS/LSPIV and other instruments. In terms of the averaged surface velocity, all measured results were in good agreement with small differences, i.e., 0.004 to 0.39 m/s and 0.023 to 0.345 m/s when compared to those from acoustic Doppler current profiler (ADCP) and surface velocity radar (SVR), respectively. The ADIS/LSPIV was further applied to measure surface velocities and discharges during typhoon events (i.e., Chan-Hom, Soudelor, Goni, and Dujuan) in 2015. The measured water level and surface velocity both showed rapid increases due to flash floods. The estimated discharges from ADIS/LSPIV and ADCP were compared, presenting good consistency with correlation coefficient R = 0.996 and normalized root mean square error NRMSE = 7.96%. The results of sensitivity analysis indicate that components till (τ) and roll (θ) of the camera are most sensitive parameter to affect the surface velocity using ADIS/LSPIV. Overall, the ADIS based upon LSPIV technique effectively measures surface velocities for reliable estimations of river discharges during typhoon events.

The resilience of towns and cities refers to their ability to adapt and recover when confronted with pressures or challenges. This study employs ten variables as indicators to assess the resilience of urban areas by analyzing official data and constructing a multilevel mixed-effects structural equation model. The empirical findings demonstrate that enhancing resilience significantly influ-ences urban service functions, such as strengthening healthcare systems, stabilizing the real estate market, and addressing socio-economic challenges. Specifically, factors such as healthcare re-sources, housing demand, population structure, and social security exhibit varying levels of resil-ience, which profoundly impact the spatial distribution of these factors and socio-economic de-velopment. Disparities in healthcare resource allocation, demographic aging trends, and shifts in the housing market closely correlate with resilience levels in different regions. Additionally, the study emphasizes that improving resilience not only boosts the reliability and security of urban services but also ensures that communities receive necessary support and protection during times of adversity. Consequently, policymakers should recognize the pivotal role of urban resilience in resource allocation and social equity, devising corresponding strategies to enhance the resilience of these areas.

Background: The aim of this study was to investigate the risk of obstructive sleep apnea (OSA) among ankylosing spondylitis (AS) patients in a nationwide population. Methods: We conducted a nationwide cohort study between 2003 and 2013 using the Taiwan National Health Insurance Research Database. The AS cohort included 2210 patients who were newly diagnosed between 2003 and 2013. Randomly selected non-AS controls were matched at a 1:4 ratio based on age, sex and index date. The endpoint of OSA was occurrence or the end of 2013. Cumulative incidences, hazard ratios (HRs) and 95% confidence intervals (CIs) were calculated after adjusting for age, gender, comorbidities and co-medications. Multivariate analyses were performed using Cox proportional hazards model. Due to violation of the proportionality assumption, landmark analysis was conducted to explore the risk of OSA during specific follow-up periods. Results: The adjusted HR (aHR) of OSA for the AS group was 2.826 (95% C.I. = 1.727–4.625) compared to the control group. On landmark analysis, aHR was 7.919 (95% C.I. = 3.169–19.792) for AS group 0–24 months from index date, and decreased to 1.816 (95% C.I. = 0.944–3.494) at ≥ 24 months from index date. On subgroup analyses increased risks of OSA in AS group compared to the control group were found for both males and females (aHRs were 4.533 (95% C.I. = 1.441–14.262) and 2.672 (95% C.I. = 1.522–4.692) for females and males, respectively). On age stratified analysis, there was significant risk only for the 40–59 age group with aHR of 3.913 (95% C.I. = 1.890–8.102). Conclusions: A higher risk of developing OSA was found among newly diagnosed AS cohort during the 12-year follow-up period, especially within 2 years after AS index date and in the 40–59 age group.

Agriculture is an industry that heavily relies on the environment. The increasing frequency of ex-treme disasters attributable to climate change has adversely affected agricultural land and dis-rupted the stability of the supply of agricultural products. Therefore, we implemented a research program focused on current strategies for adapting to agricultural meteorological disasters. The primary goal was to actively promote disaster prevention information and techniques through information platforms and applications and to provide refined forecasting and an early warning system to enhance preparedness for and recovery from agricultural disasters. This initiative can transform passive mitigation into dynamic action by disseminating crucial information to farmers. We integrated meteorological data and crop characteristics to develop disaster prevention strate-gies for the predisaster, during-disaster, and postdisaster stages to empower farmers to implement autonomous disaster prevention, ensuring their profitability and minimizing the impact of disas-ters. This paper presents an agricultural disaster prevention system involving cross-disciplinary collaboration to establish an early warning system for crop disasters. However, the effectiveness of the early warning system relies on the availability of complete meteorological and crop infor-mation, necessitating high-density agricultural meteorological stations, refined weather forecast services, historical crop damage data, and ongoing research and development on disaster preven-tion technology. In the system, a diversified social media interface is used to provide local farmers with weather forecast information. When impending disasters are identified, the platform acti-vates disaster prevention measures to reduce agricultural losses. This article paper introduces Taiwan’s agricultural disaster prevention system as a complete disaster prevention strategy.

The ozonation reaction in a bubble column reactor (BCR) has been widely used in the removal of phenol from wastewater, but the phenol removal efficiency in this type of reactor is limited because of low ozone solubility and reactivity in the system. In the present study, the phenol degradation was enhanced using α-Al2O3 as a packing material and a ZnO nanocatalyst in the BCR. The reactor diameter and height were 8 cm and 180 cm, respectively. The gas distributor was designed to include 52 holes of 0.5-mm diameter. Also, the gas holdup, pressure drop, and bubble size were measured as a function of the superficial gas velocity (i.e., 0.5, 1, 1.5, 2, 2.5, and 3 cm/s). The evaluation of the hydrodynamic parameters provided a deep understanding of the ozonation process to select the optimal operating parameters in the reactor. It was found that the best superficial gas velocity was 2.5 cm/s. A complete (100%) phenol removal was achieved for phenol concentrations of 15, 20, and 25 ppm at reaction times of 80, 90, and 100 min, respectively, using α-Al2O3 packing material and a ZnO nanocatalyst in the BCR. Additionally, the results provided a clear reaction mechanism describing the ozonized BCR. Finally, the applied treatment method can be used efficiently to remove phenol from wastewater at a low cost, with little consumed energy, and a simple operation.

Bowlby’s (1969/1982) attachment theory has been employed as a broad and integrative framework to explore human wellness across a range of disciplines. Attachment theory has even been labelled one of the last surviving “grand theories” not to have been completely dismissed, replaced, or extensively reworked (e.g., Carr, 2012; Mercer, 2011). However, despite the ubiquitous nature of some of the theory’s fundamental tenets, there are always possibilities for new conceptual development, extension, and revision. In this paper, we critically explore the idea of “context-specific” attachment within parent-child relationships. We briefly outline critical assumptions and key areas of attachment and articulate potential rationale, conceptualisation, and relevance of contextual attachment.

A multispectral superconducting nanowire single photon detector sensitive to different incident photon wavelength bands, is proposed. The SNSPD consists of a Distributed Bragg Reflector, a gold mirror, and two regions employing four NbN nanowires. Using the DBR both as a filter and a reflector, two distinct detection bands are created. The first detection band has a peak absorbance of > 0.75 at a wavelength of 1143 nm, while the second band has an absorbance of > 0.70 in the wavelength range 1440 to 2000 nm. The design of the device can be tuned to provide sensitivity in different wavelength bands. While SNSPDs do not typically provide photon wavelength sensitivity, the band-selection design proposed in this work opens up potential applications for future quantum communication technology.

The present study analyzed light emitting diodes (LEDs) as an output load and used a Taylor series to describe the characteristic curve based on the exponential characteristic of voltage and current. A prototype circuit of a flyback LED driver system was established to verify whether the theory is consistent with actual results. This study focused on the exponential relationship of LED voltage and current. Conventional simulations usually used linear models to present LED loads. However, the linear model resulted in considerable error between simulation and actual characteristics. Therefore, this study employed a Taylor series to describe the nonlinear characteristic of an LED load. Through precise calculations with Mathcad computation software, the error was effectively reduced. Moreover, the process clarified the influence of temperature on LEDs, which benefited the characteristic analysis of the entire system. Finally, a realized circuit of 120-W flyback LED drivers was established for conducting theory verification, including theoretic analysis and evaluation of the system design process of the flyback converter. The circuit simulation software SIMPLIS was used to demonstrate the system model, which enabled quick understanding of the system framework established in this study. Regarding LEDs, a commercially available aluminum luminaire was used as the output load. The measured results of the actual circuit and the simulation results were remarkably consistent. For the same system at the same temperature, the error between the simulation and actual results was less than 3%, which proved the reliability of the Taylor series simulation.

The article presents a literature review of three Chinese manuscripts containing natural dyes recipes and three containing synthetic dyes from the Ming Dynasty to the Republican Period. The manuscripts mentioned were exclusively used as references and sources. Four databases were used to access the original documents, then, a translation from old mandarin to Spanish was made. For natural dyes, the results show four dyestuffs were commonly used to produce colors, sappanwood (Caesalpinia sappan L.), followed by safflower (Carthamus tinctorius L.), indigo (Indigofera tinctoria L.), and sophora (S. japonicum L.). While the synthetic dyes exported to or produced in China were mainly bluish, greenish, and violet probably because they were difficult to obtain from natural ones. The literature review of the dyes and their recipes can be a key factor in any art history or conservation study, improving the understanding of how the colors were achieved and as complementary information for analytical analyses. It provides useful details that contribute to the preservation of Chinese dye history on silk heritage.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

Current-voltage characteristics curves of NFinFET are presented and are fitted with the modi-fied current-voltage (I-V) formulas, where the modified term in the triode region is demon-strated to be indispensable. In the as-known I-V formula, important parameters need determin-ing to make both the measured data and the fitting data as close as possible. Those parameters include kN (associated with the sizes of the transistor and mobility), (associated with Early Voltage), and Vth (the threshold voltage). The differences between the measured data and the fit-ting data vary as the applied source-drain bias, proving that the mobility of the carriers is not consistently constant. On the other hand, a modified formula, called kink effect factor, is nega-tively or positively added simulating solitary heat waves, which disturb the propagation of car-riers and thus influence the Source-Drain current (IDS). The new statistical standard deviations () are then found to be effectively suppressed as the kink effect is taken into account.

In the existing group decision-making fuzzy analytic hierarchy process (FAHP) methods, the consensus among experts has rarely been fully reached. To fill this gap, in this study, a pre-aggregation fuzzy collaborative intelligence (FCI)-based FAHP approach is proposed. In the proposed pre-aggregation FCI-based FAHP approach, fuzzy intersection is applied to aggregate experts’ pairwise comparison results if these pairwise comparison results overlap. The aggregation result is a matrix of polygonal fuzzy numbers. Subsequently, alpha-cut operations are applied to derive the fuzzy priorities of criteria from the aggregation result. The pre-aggregation FCI-based FAHP approach has been applied to select suitable alternative suppliers for a wafer foundry in Taiwan amid the COVID-19 pandemic. The experimental results revealed that the pre-aggregation FCI-based FAHP approach significantly reduced the uncertainty inherent in the decision-making process by deriving fuzzy priorities with very narrow ranges.

Buckypaper (BP), a flexible and porous material, exhibits photovoltaic properties when exposed to light. In this study, we have employed Radio Frequency (RF) Sputtering of Zinc Oxide (ZnO) followed by rapid thermal annealing to enhance the photovoltaic response of BP. We investigated the impact of various sputtering parameters, such as the gas flow ratio of argon to oxygen and deposition time, on the morphology, composition, resistivity, and photovoltaic characteristics of ZnO-modified BP. Additionally, the photovoltaic performance of the samples under different illumination modes and wavelengths was compared. It was found that optimal sputtering conditions—argon to oxygen flow ratio of 1:2, deposition time of 20 minutes, and power of 100 watts—resulted in a ZnO film thickness of approximately 45 nanometers. After annealing at 400°C for 10 minutes, the ZnO-modified BP demonstrated a significant increase in photocurrent and photovoltage, along with a reduction in resistivity, compared to unmodified BP. Moreover, under gradient illumination, the ZnO-modified BP exhibited a photovoltage enhancement of 14.70 times and a photocurrent increase of 13.86 times, compared to uniform illumination. Under blue light, it showed a higher photovoltaic response than under other colors. The enhancement in photovoltaic response is attributed to the formation of a Schottky junction between ZnO and BP, an increased carrier concentration gradient, and an expanded light absorption spectrum. Our results validate that ZnO sputtering followed by annealing is an effective method for modifying BP for photovoltaic applications such as solar cells and photodetectors.

Bat feces were reported in ancient Chinese medicine books to have the effect of reducing heat and improving eyesight, but the mechanism of vision improvement still needs further research. To this end, we used 2,2-diphenyl-1-picrylhydrazyl (DPPH) and liquid chromatography/tandem mass spectrometry (LC/MS/MS) to analyze the antioxidant capacity of and the types of vitamins in bat feces. We hoped to screen the pharmacological components of bat feces, and to explain the role that these components may play in the treatment of visual deterioration. Our results found that bat feces had a good antioxidant capacity and mainly contain vitamins B1 (thiamine), B2 (riboflavin), B3 (nicotinamide), B3 (nicotinic acid), and B5 (pantothenic acid). Although these vitamins may help maintain the health of the optic nerve and cornea, the vitamin content of bat feces is low, but the heavy metal content is high, as shown using inductively coupled plasma mass spectrometry (ICP-MS) analysis. Therefore, we suggest that the use of bat feces as traditional Chinese medicine to improve vision should be strictly restricted.

This work reports the first nanocrystalline SnON (7.6 % Nitrogen content) n-type nanosheet Field-Effect Transistor (nFET) with transistor’s effective mobility (µeff) as high as 357 and 325 cm2/V-s at electron density (Qe) of 5×1012 cm-2 and ultra-thin body thickness (Tbody) of 7 and 5 nm, respectively. At the same Tbody and Qe, these µeff values are significantly higher than single crystalline Si, InGaAs, thin-body Si-on-Insulator (SOI), two-dimensional (2D) MoS2 and WS2. New discovery of slower µeff decay rate at high Qe than SiO2/bulk-Si universal curve was found, owing to one order of magnitude lower effective field (Eeff) by more than 10 times higher dielectric constant () in channel material, which keeps the electron wave-function away from the gate-oxide/semiconductor interface and lowers the gate-oxide surface scattering. In addition, the high µeff is also due to the overlapped large radius s-orbitals, low 0.29 mo effective mass (me*) and low polar optical phonon scattering. SnON nFETs with record-breaking µeff and quasi-2D thickness enable potential monolithic three-dimensional (3D) integrated circuit (IC) and embedded memory for 3D biological brain-mimicking structures.

All humans will experience the process of birth, old age, illness, and death. However, when faced with life-sustaining decisions, the families of patients are often faced with medical decisions as surrogates. In recent years, the families of patients have started to value the importance of the right to palliative care, although this often requires lengthy discussions. Therefore, this study explored the predictability of factors that affect the feeling experienced by patients’ families when signing Do-Not-Resuscitate Consent. This study used a cross-sectional study and interviewed 90 family members using a structural questionnaire. The study hypotheses were tested using a t-test, one-way analysis of variance, product–moment correlation, and hierarchical regression analysis. Attribute variables of family members, such as gender and whether they live with the patient, are predictors that affect the family member’s feeling experience when signing Do-Not-Resuscitate Consent. The emotional support from medical professionals to family members helps the family member to express their negative feelings on signing Do-Not-Resuscitate Consent; more informational support information provided to family members by medical professionals can alleviate negative feelings felt by family members when signing Do-Not-Resuscitate Consent. This study identified that family members’ knowledge about Do-Not-Resuscitate acquired from medical professionals is relatively low. It is suggested that critical care units regularly conduct training on hospice palliative care, implement standard care procedures of hospice palliative care at critical care units, and provide detailed medical information about advanced decisions to family members so as to reduce their emotional stress. This will ensure that intensive care units can also achieve the goal of critically ill hospice palliative care.

Student mobility is one of the most important indicators to reflect institutional internationalization in a sustainable higher education system. While student mobility issues have been addressed persistently, the phenomenon is rarely discussed in association with higher education expansion. Since higher education sustainable development has received much scholarly attention, monitoring student mobility flows to adjust international strategies is necessary. This study explored practical approaches to detect student mobility flows in the process of higher education expansion. Targeting Taiwan’s higher education system as an example, we addressed the topic of system expansion and the core issues of student mobility. Target series data were collected from 1950 to 2021, including higher education enrollment, gross enrollment ratio (GER), and number of inbound and outbound students. The data were transformed with index formats, for example enrollment increasing ratio (IR) and net flow ratio. The cross-correlation function (CCF) and autoregressive integrated moving average (ARIMA) were used to determine the correlations of the series data and their future trends. The findings suggested that the effect of system expansion, with GER and IR, might influence the mobility ratios significantly in the process of higher education expansion. This study confirmed that the time series approaches work well in detecting the phenomena of higher education expansion and their effects on student mobility flows in the future.

Coastal wave modeling and forecasting are essential in oceanography, sustainable marine energy, and ocean engineering. Precise forecasting of wave speed and direction are crucial for offshore operations, marine energy, risk management, environmental management, coastal and sustainable maritime management. The coastline of Brunei Darussalam can generate between 15 and 126 Giga Watt of wave energy. In this experimental research, we used two numerical approaches, the finite difference, and spectral element methods, to model and simulate wave speed and direction. We calculated the mean error between numerical and analytical solutions. We proposed a novel, promising, univariate time series forecasting model by combining the Long Short-Term (LSTM) with KerasTuner hyperparameters tuning and optimization techniques. This method helps us to improve the accuracy and efficiency of time-series forecasting.. The experimental data was computed from high-precision Acoustic Doppler Current Profiler (ADCP) sensor data. This research is part of the preliminary feasibility analysis of wave energy production in Brunei Darussalam and net zero commitment for a sustainable environment. Seven independent forecast experiments were performed for wave speed and direction in degree and radian units for 1, 3, 6, 8, 10, 12, and 24 hours. Mean squared error (MSE) was adopted as a metric for both training and testing. The experimental results reveal that the wave speed forecast has the lowest MSE compared to direction, regardless of the unit of measure, but has a longer duration. In addition, the direction forecast in the degree unit has the lowest errors compared to the unit of radians; the latter has a longer running time than the former. The model has delivered optimal results throughout the experiments with minor training and test errors. We conducted a thorough evaluations on two benchmark time series datasets, which include the study dataset and air quality index dataset, to validate the performance of the proposed model with other models. The proposed model outperforms cutting-edge forecasting models, such as the conventional LSTM, ARIMA, and Prophet. The model has the slightest forecast error compared to the existing literature’s result.

The introduction of ChatGPT in academia has raised significant concerns, particularly regarding issues like plagiarism and the ethical use of generative text for academic purposes. Existing literature has predominantly focused on ChatGPT adoption, leaving a notable gap in addressing the strategies users employ to mitigate these emerging challenges. To bridge this gap, this research utilizes the Uncertainty Reduction Theory (URT) to formulate user strategies for reducing uncertainty. These strategies include both interactive and passive approaches. Concurrently, the study identifies key sources of uncertainty, which include concerns related to transparency, information accuracy, and privacy. Additionally, it introduces the concepts of seeking clarification and consulting peer feedback as mediating roles to facilitate reduced uncertainty. We tested these hypotheses with a sample of Indonesian users (N = 566) using structural equation modeling via Smart-PLS 4.0 software. The results confirm that interactive Uncertainty Reduction Strategies (URS) are more effective in reducing uncertainty when using ChatGPT compared to passive URS. Transparency concerns, information accuracy, and privacy concerns are identified as factors that increase the level of uncertainty. In contrast, consulting peer feedback is the most effective strategy for reducing uncertainty compared to seeking clarification at the individual-system level. Insights from the mediating effects confirm that consulting peer feedback significantly mediates uncertainty sources to reduce uncertainty. The study discusses various strategies for the ethical use of ChatGPT by users in the educational context and contributes significantly to theoretical development.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

The black hole (BH) phenomenon is an intraluminal restenotic lesion. It was identified by intravascular ultrasound (IVUS) and optical coherence tomography (OCT) after intracoronary brachytherapy and drug-eluting stent implantation. Despite the similarity in the mode of action of brachytherapy and drug-eluting stent implantation, the BH phenomenon appears to be uncommon after drug-eluting stent implantation. Specifically, the BH phenomenon is better identified by OCT than by IVUS. Herein, we present a case of in-stent restenosis with suspected BH phenomenon on IVUS confirmed by OCT.

In a collaborative forecasting task, experts may have unequal authority levels. However, this has rarely been considered reasonably in the existing fuzzy collaborative forecasting methods. In addition, experts may not be willing to discriminate their authority levels. To address these issues, an auto-weighting fuzzy weighted intersection (FWI) fuzzy collaborative intelligence approach is proposed in this study. In the proposed auto-weighting FWI fuzzy collaborative intelligence approach, experts’ authority levels are automatically and reasonably assigned based on their past forecasting performances. Subsequently, the auto-weighting FWI mechanism is established to aggregate experts’ fuzzy forecasts. The theoretical properties of the auto-weighting FWI mechanism have been discussed and compared with those of the existing fuzzy aggregation operators. After applying the auto-weighting FWI fuzzy collaborative intelligence approach to a case of forecasting the yield of a DRAM product from the literature, its advantages over several existing methods were clearly illustrated.

Multicellular organisms organize themselves according to two principles; first, the equilibrium between the driving force of unstable state cells and apoptosis or senescence; and second, the mutual equilibrium between the functional requirements of different types of cells. For the first principle, we deduce that stem cells at different levels have their own growth limits, which are determined by two factors: the ability of the stem cells to enter an unstable state (specifically, the ability of cells to divide and differentiate); and the rate of cellular senescence, loss of function, and finally, apoptosis. The superposition of stem cell limits at different levels over each other can amplify small differences at the genetic level. Moreover, the growth limits of different organs are different, which lead to different individuals having completely different appearances. The second principle is that the sum of the specific output functions of an organ must be equal to the overall demand for the function to be provided by the organ. If negative entropy input can meet this equilibrium, defects in certain genes will cause these defective individuals to become larger or develop other morphology.

The bridge crane is often used in a complex environment, often subject to interference of all loads. Some uncertainties factors often have an inevitable impact on its swing. So the force situation of the bridge crane during a working cycle is analyzed, and a three-dimensional dynamic mathematical model of the bridge crane is built. Through the simulation analysis of the model under the action of driving force and wind load, the change law of the swing angle of the bridge crane is studied. Then, the fuzzy control theory is used to determine the control parameter in the anti sway control process. The position, swing angle deviation and deviation rate of the bridge crane are taken as the input, and the parameter correction is obtained after the fuzzification by using the center of gravity method, the anti sway fuzzy control system of the bridge crane is designed and simulated. The research results show that the fuzzy PID anti sway controller can not only improve the adaptability of the control system, but also overcome the large overshoot, quickly restrain the swing, and effectively realize the anti sway function of the bridge crane.

Mild cognitive impairment (MCI) is when brain function declines. It is a transition stage between normal aging and Alzheimer's disease (AD) and may be an underlying symptom of AD. Improper use of test instruments or imperfect test methods in clinical practice often leads to variations in test results. In addition, there may be resistance from the subject if he/she has to undergo multiple screening tests simultaneously. Therefore, the objective of this study was to use virtual reality to create an image testing scenario that integrates Mini-Cog, Short Portable Mental Status Questionnaire (SPMSQ), Mini-mental Status Examination (MMSE), Saint Louis University Mental Status Examination (SLUMS), Clinical Dementia Rating (CDR), and Cognitive Abilities Screening Instrument (CASI), and combine fuzzy logic control (FLC) technology to develop an MCI forecasting system. There were 24 middle-aged to older adults aged 50 to 65 years who participated in the evaluation experiment. The results showed that the MCI forecasting system developed in this study is highly correlated with the traditional screening tests, including Mini-Cog, SPMSQ, MMSE, SLUMS, and CASI. The forecasting system can provide an integrated reference score for testers in making judgments. In addition, the distribution of the System Usability Scale (SUS) evaluation scores for the MCI forecasting system revealed that 87.5% were grade C (good to use) or above, and 29.2% were grade B (extremely good to use) or above. The forecasting system receives positive feedback from the subjects.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

The development of using mitochondrial transplantation in medical therapy are currently discussed. According to the endosymbiotic theory, the movement of mitochondria between different cells is possible. Therefore, an idea of transferring the mitochondria purified from the cells with a limited lifespan to shorten the lifespan of immortal cancer cells was generated. Human umbilical vein endothelial cell (HUVEC) is a kind of primary cell with a limited lifespan. In the present study, the mitochondria purified from HUVEC were applied to alter the malignance of B16F10 melanoma cell. In the comparison of the basic function of mitochondria, HUVEC mitochondria exhibited a higher mitochondrial membrane potential (MMP), while the lower levels in ATP, mitochondrial DNA (mt-DNA) and mitochondrial protein (mt-protein) as compared to melanoma B16F10. After transplanted the B16F10 with HUVEC mitochondria, the migration, invasion, and the proteins involved in cancer stemness were decreased, however, the proteins involved in cell proliferation, such as cyclin D1 and cyclin E1 were increased. In addition, the levels of ATP, mt-DNA and mt-protein of B16F10 were also reduced. As for the dynamics of mitochondria, the reduced expressions of DRP1 and LC3 II revealed that transferred mitochondria can attenuate the mitophagy of B16F10. In mice, inoculated the B16F10 carrying the transplanted HUVEC mitochondria resulted in the larger size of tumor, which is corresponded to the higher levels of cyclin D1 and E1. Interestingly, the lower expressions of N-cadherin, α-SMA and MMP-9 reveled the tumor were decreased in mesenchymal characteristics. Therefore, despite the HUVEC mitochondria did not inhibit the proliferation of B16F10, the metastatic characteristic was reduced.

Background: Extracorporeal cardiopulmonary resuscitation (ECPR) has gradually come to be regarded as an effective therapy, but the hospital mortality rate after ECPR is still high and unpredictable. The present study tested whether age-adjusted Charlson comorbidity index (ACCI) can be used as an objective selection criterion to ensure the most efficient utilization of medical resources. Methods: Adult patients (age ³ 18 years) receiving ECPR at our institution between 2006 and 2015 were included. Data regarding ECPR events and ACCI characteristics were collected immediately after extracorporeal membrane oxygenation (ECMO) setup. Adverse events during hospitalization were also prospectively collected. The primary endpoint was survival to hospital discharge. The second endpoint was short-term (2-year) follow-up outcome. Results: A total of 461 patients included in the study were grouped into low ACCI (ACCI 0–3) (240, 52.1%) and high ACCI (ACCI 4–13) (221, 47.9%) groups. The median ACCI was 2 (IQR: 1–3) and 5 (IQR: 4–7) for the low and high ACCI groups, respectively (P < 0.001). Cardiopulmonary resuscitation (CPR)-to-ECMO duration was comparable between the groups (42.1 ± 25.6 and 41.3 ± 20.7 min in the low and high ACCI groups, respectively; P = 0.754). Regarding hospital survival rate, 256 patients (55.5%) died on ECMO support. A total of 205 patients (44.5%) were successfully weaned off ECMO, but only 138 patients (29.9%) survived to hospital discharge (32.1% and 27.6% in low and high ACCI group, P = 0.291). Multivariate logistic regression analysis revealed CPR-to-ECMO duration and CPR cause of septic shock as significant risk factors for hospital survival after ECPR (P = 0.043 and 0.014, respectively), whereas age and ACCI were not (P = 0.334 and 0.164, respectively). The 2-year survival rate after hospital discharge for the 138 hospital survivors was 96% and 74% in the low and high ACCI groups, respectively (P = 0.002.)Conclusions: High ACCI before ECPR does not predict poor outcome of hospital survival. Therefore, ECPR should not be rejected solely due to high ACCI. However, high ACCI in hospital survivors is associated with a higher 2-year mortality rate than low ACCI, and patients with high ACCI should be closely followed up.

An oceanic radar altimeter such as TOPEX/Poseidon (T/P) is typically for observing elevation changes over the open oceans or large inland lakes/rivers, with limited applications over solid earth due to its large footprint and susceptibility to waveform contamination and slope effect. Here we demonstrate that it is possible to construct a long-term time series of glacier elevation change from T/P-series radar altimeters over two flat surfaces near a glacier terminus and an icefield (Sites A and B, with slopes of 2° and 0.8°) in Mt. Tanggula, Tibet, at elevations over 5400 m. We retracked radar waveforms using the subwaveform threshold algorithm, selected quality altimeter data (1/4 of the original) with nearly the same slope and adjusted the original elevations by fitting with a time-varying, 2nd order surface. The glacier elevation changes at the two sites from T/P (1993–2002) show seasonal elevation oscillations with linear rates at about −3 m/year and abnormal seasonal changes around the 1997–98 El Niño. Site A is over a deep valley in southern Tanggula. Its elevation dropped about 30 m over 1993–2002 (from T/P) and the glacier almost disappeared by 2016 (from altimeters and satellite images). Despite the sporadic Jason-2 and Jason-3 altimeter data, we also derived long-term rates of glacier elevation change over 1993–2017. Landsat-derived glacier area and elevation changes near the two sites confirm the rapid glacier thinning from the altimeters. The glacier meltwater near Site A supplied increasing source water to Chibuzhang Co west of Mt. Tanggula, contributing partially to its accelerated rising lake level. The glacier thinning at Site B (icefield) was correlated with the increased discharge of the Tuotuo River in eastern Mt. Tanggula, a source region of the Yangtze River. The successful detection of glacier thinning at the two sites shows that T/P-series altimeters can serve as a virtual station at a flat glacier spot to monitor long-term glacier elevation changes in connection to climate change. This virtual station concept is particularly useful for inaccessible glaciers, but its implementation faces two challenging issues: increasing the volume of quality altimeter data and improving the ranging accuracy over a targeted mountain glacier spot.

Advanced electrode designs have made single-unit neural recordings commonplace among modern neuroscience research. However, single-unit resolution remains out of reach for the intrinsic neurons of the gastrointestinal system. Single-unit recordings of the enteric (gut) nervous system have been conducted in anesthetized animal models and excised tissue, but there is a large physiological gap between awake and anesthetized animals, particularly for the enteric nervous system. Here, we describe the opportunity for advancing enteric neuroscience offered by single-unit recording capabilities in awake animals. We highlight the primary challenges to microelectrodes in the gastrointestinal system including structural, physiological, and signal quality challenges.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

Using lightweight fire-rated board (LFRB) presents cost-effective opportunities for various passive fire protection measures. The aim of the project is to develop a LFRB with enhanced fire resistance, acoustic properties, and mechanical properties. These properties were determined using the Bunsen burner, furnace, energy dispersive X-Ray, impedance tube instrument, and Instron universal testing machine. To fabricate the LFRBs, vermiculite and perlite were blended with flame-retardant bind-ers, and four types of LFRBs were produced. A fire test was conducted to compare the fire-resistance performance of the LFRBs with a commercially available flame retardant board. The B2 prototype showed exceptional fire-resistant properties, with a temperature reduction of up to 73.0 °C as compared to the commercially available fire-rated magnesium board. Incorporating nano chicken eggshell into the specially formulated flame-retardant binder preserved the LFRBs’ structural integrity, enabling them to withstand fire for up to 120 minutes with an equilibrium temperature of 92.6 °C. This approach also provided an absorption coefficient of α = 2.0, a high flexural strength of 3.54 MPa, and effective flame retardancy properties with a low oxygen/carbon ratio of 2.60. These results make the LFRBs valuable for passive fire protection applications in the construction and building materials industry.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

Weed seedbank is an indication of future weed infestation potential of the species and is essential for making strategic planning for its sustainable management. Parthenium weed (Parthenium hysterophorus L.) is an invasive alien species threatening the biodiversity and the environment in Malaysia. A study was, therefore, conducted to estimate the soil seedbank of the weed at four soil depths of four villages of Kuala Muda, Kedah. The aim was to indicate the critical s of parthenium weed seedbank in Malaysia. Soil samples were collected from the sites using a soil core. The seeds were extracted from the soil samples with sieve shaker at the Universiti Malaysia Kelantan laboratory, Jeli Campus. The study indicates that the weed seedbank is in critical level at the area. The highest number of weed seeds (6915/m2) was found in Kg. Kongsi 6, followed by Kg. Sungai Tok Rawang (4481 seeds/m2). The top layer of soil, 0-5 cm, contained the maximum number of weed seeds (4878 seeds/m2) and a significant number of seeds (316 seeds/m2) were noticed at 10-15 cm soil depth. The study suggests the Malaysian government to take immediate action to control parthenium weed seedbank of the sites.

This study explores the relationship between mental and physical therapeutic through three dimensions: man-environment relationships; a sense of place and symbolic landscapes. The study used a combination of qualitative and quantitative research methods. Local residents living in the coastal area of Xinglin Bay are the research objects. Quantitative data analysis revealed that the frequency of residents' visits was an important variable affecting their physical and treatment perceptions. In addition, the significance is higher for females than for males. The text analysis shows that the environment, especially the ecological restoration of water quality and migratory birds, is of great significance to the identity of local residents. Daily activities contribute to a sense of place and are what make the coast a place of therapeutic landscape function.

Recent advancements in semiconductor photonic and electronic devices such as Uni-travelling-carrier photodiodes (UTC-PDs), have played a significant role in the development of Terahertz communication technology. However, a major challenge that still persists is the limited output power from a single UTC-PD required for practical transmission distances. To enhance the output power, we propose and demonstrate a novel Terahertz wave power combining technique using a photomixer device that comprises of two arrayed UTC-PDs monolithically integrated with a microstrip line-based 2 × 1 Wilkinson power combiner and a rectangular patch antenna on a Silicon Carbide (SiC) substrate at 300 GHz. At photocurrents of 8 mA and 10 mA from the two UTC-PDs, the device experimentally exhibited a 7.3 dB increase in power relative to the power obtained with 8 mA UTC-PD and a 4.4 dB increase in power relative to the power obtained with 10 mA UTC-PD, when both UTC-PDs were irradiated. This implies that power can be enhanced by a factor of N2 if the photocurrent is multiplied by a factor of N. This technology presents a holistic and cutting edge platform for further power multiplication by further increasing the number of arrayed UTC-PDs.

Nutrients are the driving force of plant and herbivore interactions. Different elements and fertilization levels in soil, or artificially fertilized substrates can have a direct impact on plant defense responses. Meanwhile, nutrient levels mediated by root associated microbes can indirectly affect plant-herbivore interactions. Nutrient uptake promoted by beneficial mycorrhizal fungi or rhizobacteria interacting with roots can stimulate plant tolerance to herbivore attack, as evidenced by herbivore performance, plant nutrient status, plant biomass allocation and compensatory growth. In return, herbivory affects nutrient fluxes between plants and their associated beneficial microbes. Furthermore, aboveground and belowground herbivory can affect the nutrient exchange between plants and soil microbial communities, mainly for carbon-and nitrogen-based resources supporting herbivores´ life cycles. These ecological interactions are governed by jasmonic acid (JA) and key enzymes on the molecular level. This review summarizes the current scientific literature on the role of nutrients in plant-herbivore interactions. This will support efforts to optimize plant defense strategy via managing nutrient variance.

The purpose of this paper is to construct an evaluation system for AI painting software based on generative adversarial network technology, which optimizes the performance of the related software in terms of functionality, ease of use, system performance and safety. The results of the questionnaires are statistically analyzed. In addition, exploratory factor analysis was supported to extract the data of the study, which was ultimately used to calculate the weight and importance of each index through fuzzy hierarchical analysis method. The study constructed an evaluation system for AI painting software based on generative adversarial network technology, including 16 indicators of functionality, 16 indicators of ease of use, 7 indicators of system performance, and 8 indicators of safety respectively that their alpha coefficients were 0.882, 0.962, 0.932, 0.932, and 0.932, respectively. In addition, the accumulated explanatory variances of their coefficients were 84.405%, 84.897%, 84.013%, and 72.606%, respectively, 73.013%, and 72.606%, respectively. It is clear that the items included in each of the indicators are homogeneous, with a high degree of internal consistency. This paper suggests that the development of AI painting software focusing on functionality, ease of use, system performance and safety can enhance the market competitiveness of the software.

Federated learning (FL) has become a burgeoning and attractive research area, which provides a collaborative training scheme for distributed data sources with privacy concerns. Most existing FL studies focus on taking unimodal data, such as images and text, as the model input and resolving the heterogeneity challenge, i.e., the non-identically distributed (non-IID) challenge caused by data distribution imbalance related to data labels and data amount. In real-world applications, data are usually described by multiple modalities. However, to the best of our knowledge, only a handful of studies have been proposed to improve the system performance by utilizing multimodal data. In this survey paper, we identify the significance of this emerging research topic – multimodal federated learning (MFL) and perform a literature review on the state-of-art MFL methods. Furthermore, we categorize multi-modal federated learning into congruent and incongruent multimodal federated learning based on whether all clients possess the same modal combinations. We investigate the feasible application tasks and related benchmarks for MFL. Lastly, we summarize the promising directions and fundamental challenges in this field for future research.

Streptococcal infection is a main infectious diseases for farmed grey mullet (Mugil cephalus). This study were to identify spreptococcal species in diseased farmed grey mullet and to investigate differences in susceptibility to 13 antibiotics and in genotypes between the stains from the grey mullet and non-grey mullet. 170 samples from diseased farmed grey mullet were collected from three county in 2013 -2016. Multiplex PCR identified L. garviea (146) as the main pathogen, S. agalactia (9), S. dysgalactiae (19), and double infection (5), but no S. iniae. The prevalence changed annually and differed among three counties. Pulsed-field gel electrophoresis (PFGE) analysis demonstrated identical genotype with an ApaI-digested DNA pattern. Disc diffusion results demonstrated differences in antibiotic susceptibility between the strains from grey mullet (146) and non-grey mullet (30). Almost all strains resisted to clindamycin and all strains were susceptible to six antibiotic in grey mullet and 4 antibiotics in non-grey mullet. The reduced susceptible strains was more in non-grey mullet than grey mullet group. The reduced susceptible strains were observed the highest in 2014 and in Chiayi county and decreased from 2014 to 2016. However, the strains with reduced susceptibility to ceftriaxone, cirpofoxacin, moxifloxacin, tetracycline for human treatment were observed.

To investigate the effect of nitrogen (N) application on carbon metabolism and yield of flag leaves and grains of spring wheat under drip irrigation in Xinjiang, a split - plot design was adopted from 2020 to 2021, with strong gluten wheat Xinchun 37 (XC37) and medium gluten wheat Xinchun 6 (XC 6) as the main plot factor and different nitrogen application rates as subplot factor. Four nitrogen application rates of 0, 210, 255 and 300 kg·hm-2 (CK2, B1, A1 and CK1, respectively) were set to analyze and compare the nitrogen response of key enzyme activity, soluble sugar, sucrose and starch content in flag leaves and grains to control yield formation. The results showed that with the increase of nitrogen application, Sucrose phosphate synthetase (SPS) and sucrose synthetase (SS) in flag leaves, SS in seeds, activities of adenosine diphosphate pyrophosphorylase (ADPG - PPase), soluble starch synthase (SSS), bound starch synthase (GBSS) and starch branching enzyme (SBE) in seeds, contents of soluble sugar and sucrose and yield in flag leaves increased first increasing and then decreasing. The A1 treatment (255 kg·hm-2) showed significant differences compared to other treatments, with increases of 7.95–158.33%, 8.69–155.12%, 7.65–53.25%, 5.41–62.83%, 2.85–85.52%, 3.08–57.30%, 8.87–79.16%, 9.33–196.55%, 9.43–112.78%, and higher levels of amylose, amylopectin, and total starch content than other treatments by 1.86–30.38%, 10.58–83.69%, and 7.96–63.09%, respectively. Correlation and stepwise regression analysis indicate highly significant positive correlation between yield and solube sugar and sucrose of flag leaves and grains, as well as their key emzymes and starch. Among them, soluble sugar in grains, amylopectin, and sucrose in grains have the greatest impact on the yield of XC37, determining 84.5% of its yield. SSS, soluble sugars in grains, amylopectin, and SBE have the greatest impact on the yield of XC 6, determining 80.4% of its yield. The starch shows a highly significant positive correlation with ADPG - PPase, SSS, GBSS, and SBE. There is a significant interaction effect between nitrogen application rate and variety, with better performance observed in Xinchun 37 compared to Xinchun 6. Under drip irrigation conditions in arid areas, nitrogen application of 255 kg·hm-2 can effectively regulate the metabolism of sucrose to starch in flag leaves and grains of spring wheat, which is conducive to the accumulation of starch in grains and the formation of yield.

Spectacular shifts have been led to by The COVID-19 crisis in consumer behavior. Retailers will have to work hard to meet ever-evolving customer service experience with respect to the ways in which it may be differently affected by offline or online transactions in order to win and stay relevant. We suggest an integrative framework and construct customer service experience hypotheses, based on its antecedents and consequences that will contribute to academic study as well as managerial implications. The hypotheses are tested by a simultaneous equation model employing two data sets of the retail industry's offline and online customers. In this study, 571 samples of these businesses, 319 and 252 respondents from offline and online retail channels, respectively, were collected by means of an online web survey of consumers. The results show that the impact of consequences and antecedents of CSX differs based on the media utilized. The integrative framework of CSX in its online medium is far more effective than its explanatory power offline. The outcomes are reasonably counterintuitive in so far as they demonstrate that while most elements of CSX where a service is selected offline is the same in terms of customer loyalty and value equity, the emotional element related to the service provider is higher when the service is selected offline rather than online. These outcomes indicate that, contrary to popular fears, the online medium enables firms to develop a loyal customer foundation. These findings offer perceptivity into how an online channel could be used to better complement the offline channel, contributing towards new knowledge and understanding on CSX and how it may be utilized for managerial decision-making.

In the future, the power of commercial ocean current generators can reach MW level, and the corresponding mooring rope tension is very great. But the power of the ocean current generator in research stage is KW level and it can bear less rope tension. Its main mooring rope adopts a single cable and a single foundation. This paper studies the dynamic response and rope tension of the MW-level ocean current generator mooring system. It is assumed that the commercial MW-level ocean current generator is similar to the research-type KW level, and the similarity law and several dimensionless similar parameters are proposed, including for the turbine and platform the power number, tip speed ratio, hydrodynamic damping and stiffness coefficient and others. Based on these dimensionless similar formula and the known parameters of the researched KW-level convertor, all parameters of the MW-level ocean current generator are derived. In order to overcome the extreme tension of a MW-level mooring system and provide good stability, this paper proposes the pulley-traction rope design to replace the traditional single traction rope design. The static and dynamic mathematical models of this mooring system subjected to typhoon wave impact and current are proposed and analytical solutions are obtained. The study found that the dynamic rope tension of the MW-level system with the traditional single rope system is significantly greater than its fracture strength and the dynamic tension of the pulley- traction rope system. It means that this design can effectively reduce the dynamic rope tensions of the mooring system. Moreover, if the length ratio of rope A to the seabed depth is within a safe range, the maximum rope dynamic tension will be less than the fracture strength. In addition to the MW level, the dynamic response of the 700kW level power generation system under the action of typhoon waves is also studied. It is discovered that the dynamic tension of rope D is the largest. In addition, the dynamic tension of rope D for 700kW system will exceed the original strength of design. However, only the specification of rope D is increased, the new dynamic tension is still close to the original such that the dynamic tension of rope D is significantly less than the adjusted fracture strength and the mooring system becomes safety.

It is desirable to upgrade previous evolutionary theories, which have remained incomplete and controversial for decades. Here we employ the concept of carbon-based entities (CBEs), which include methane, amino acids, proteins, organisms, and other entities containing relatively many carbon atoms. We deduce the driving force, mechanisms, steps, modes, tempos of CBE evolution, through integration of biology, physics, and chemistry using logics for complex issues. We hence establish the Carbon-Based Evolutionary Theory (CBET). The CBET suggests that evolution is the increase in hierarchy, diversity, fitness of CBEs under natural selection and driven by thermodynamics due to the chemical effect of the thermodynamic features of the Earth on CBEs. It provides better explanations for life origin, macroevolution events, natural selection, sympatric speciation, and evolution tempos than previous evolutionary theories. It reveals the evolutionary basis of multiple important social notions, including diversity, collaboration, altruism, obeying rules, and proper increase in freedom. It refutes some wrong notions in thermodynamics, including negative entropy (negentropy) and that biological order is equal to thermodynamic order, which have misled many people. The CBET is supported by its deduction and application. It could be a rare bridge linking laws of thermodynamics, evolution of life, and development of human society, and could have great significance in various sciences.

DC residential distribution system (RDS) consisted by DC living home will be a significant integral part in the future green transmission. Meanwhile, the increasing number of distributed resources and intelligent devices will change the power flow between main grid and demand sides. The utilization of distributed generations (DGs) requires an economic operation, stability, environmentally friendly in the whole DC system. This paper not only presents an optimization schedule and transactive energy (TE) approach through centralized energy management system (CEMS), but a control approach to implement and ensure DG output voltages to various DC buses in DC RDS. Based on data collection, prediction and a certain objection, the expert system in CEMS can work out the optimization schedule, after this, the voltage droop control for steady voltage is aligned with the command of unit power schedule. In this work, a DC RDS is as a case study to demonstrate the process, the RDS is associated with unit economic models, cost minimization objective is proposed to achieve based on real-time electrical price. The results show that the proposed framework and methods will help the targeted DC residential system to reduce the total cost and reach stability and efficiency.

This paper reports the efforts made and experiences gained in developing the Flood Prevention and Emergency Response System (FPERS) powered by Google Earth Engine, with focus on its applications at the three stages of floods. At the post-flood stage, FPERS integrates various remote sensing imageries, including Formosat-2 optical imagery, to detect and monitor barrier lakes, synthetic aperture radar imagery to derive an inundation map, and high-spatial-resolution photographs taken by unmanned aerial vehicles to evaluate damage to river channels and structures. At the pre-flood stage, a huge amount of geospatial data are integrated in FPERS and are categorized as typhoon forecast and archive, disaster prevention and warning, disaster events and analysis, or basic data and layers. At the during-flood stage, three strategies are implemented to facilitate the access of the real-time data: presenting the key information, making a sound recommendation, and supporting the decision-making. The example of Typhoon Soudelor in August of 2015 is used to demonstrate how FPERS was employed to support the work of flood prevention and emergency response from 2013 to 2016. The capability of switching among different topographic models and the flexibility of managing and searching data through a geospatial database are also explained, and suggestions are made for future works.

Combining Matrix-Assisted Laser Desorption/Ionization Time-of-Flight (MALDI-TOF) spectra data and artificial intelligence (AI) has been introduced for rapid prediction on antibiotic susceptibility test (AST) of S. aureus. Based on the AI predictive probability, the cases with probabilities between low and high cut-offs are defined as “grey zone”. We aimed to investigate the underlying reasons of unconfident (grey zone) or wrong predictive AST. A total 479 S. aureus isolates were collected, analyzed by MALDI-TOF, and AST prediction, standard AST were obtained in a tertiary medical center. The predictions were categorized into the correct prediction group, wrong prediction group, and grey zone group. We analyzed the association between the predictive results and the demographic data, spectral data, and strain types. For MRSA, larger cefoxitin zone size was found in the wrong prediction group. MLST of the MRSA isolates in the grey zone group revealed that uncommon strain types composed 80%. Amid MSSA isolates in the grey zone group, the majority (60%) was composed of over 10 different strain types. In predicting AST based on MALDI-TOF AI, uncommon strains and high diversity would contribute to suboptimal predictive performance.

(1)Background: This report was an effective evaluation of using multimedia educational program for self-care and quality of life in patients with a stoma at postoperative and established a simple threshold for enterostomy self-care skills.(2)Methods:108 patients with enterostomy were randomly assigned to receive either the intervention multimedia education program (including information about preparation for enterostomy care, cleaning method, manual bag replacement steps and precautions). The primary outcome was self-care ability and quality of life (defined as overall enterostomy self-care ability and overall quality of life), which was assessed at 2 weeks after intervention via an interview.(3)Results: Compared with those who in the conventional stoma education program, patients received the multimedia education program significantly improved their overall self-care ability and quality of life in statistically. The threshold of the enterostomy self-care skill scale was 20 points, and its corresponding sensitivity was 77.8%, and the specificity was 75.7%.(4)Conclusions: According to our study, the multimedia education program could enhance self-care ability of home care and quality of life in patients with enterostomy.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

Oral squamous cell carcinoma (OSCC) remains an under-studied and significant global cancer killer and dismal survival rates have not changed in decades. A better understanding of the molecular basis of OSCC progression and metastasis is needed to develop new approaches for treating this disease. The supportive network surrounding cancer tumor cells known as the tumor microenvironment (TME) has gained increasing interest lately since it performs essential pro-tumorigenic functions. Cancer-associated fibroblasts (CAFs) are one of the main cell types in the TME and are known to play a key role in influencing the biological behavior of tumors. CAFs present a heterogeneity both in phenotype as well as functions, leading to the suggestion of different CAF subtypes in several cancer forms. The task to subtype CAFs in OSCC has however just begun and there is today no united way of subtyping CAFs in this disease. This review aims to define the features of CAFs and to summarize CAF subtype research in OSCC including aspects as disease prognosis and therapeutic opportunities.

A case-crossover study examined how PM_2.5 from Asian Dust Storms (ADS) affects the number of emergency room (ER) admissions for cardiovascular diseases (CVDs) and respiratory diseases (RDs). Our data indicated that PM_2.5 concentration from ADS was highly correlated with ER visits for CVDs and RDs. The odds ratios (OR) increased by 2.92 (95% CI: 1.22-5.08) and 1.86 (95% CI: 1.30-2.91) per increase 10 µg/m³ in PM_2.5 levels, for CVDs and RDs, respectively. A 10 µg/m³ increase in PM_2.5 from ADSs was significantly associated with increase in ER visits for CVDs among those 65 years of age and older (an increase of 2.77 in OR) and for females (an increase of 3.09 in OR). In contrast, PM_2.5 levels had a significant impact on RD ER visits among those under 65 years of age (OR=1.77). The risk of ER visits for CVDs increased on the day when the ADS occurred in Taiwan and the day after (lag 0 and lag 1); the corresponding risk increase for RDs only increased on the fifth day after the ADS (lag 5). In Taiwan’s late winter and spring, the severity of ER visits for CVDs and RDs increases. Environmental protection agencies should employ an early warning system for ADS to reduce high-risk groups’ exposure to PM_2.5.

Microbial-mediated biogeochemical cycling of iron is widespread in anaerobic environments such as sediments and deep Earth aquifers, and is one of the major pathways for metabolising iron in nature. Organic matter containing quinone groups can act as electron shuttles to transfer electrons between microorganisms and Fe(III) oxides, facilitating the biotransformation of iron; this process also influences the transport transformation of pollutants. In this paper, the reduction of Fe(III) oxides by aniline in the heterogeneous iron-reducing bacterium Shewanella oneidensis MR-1 mediated by the electron shuttle AQS was investigated. The results showed that aniline significantly promoted the reduction of Fe(III) by MR-1 in the AQS-mediated reaction, and the best Fe(III) reduction was achieved in the reaction group of "GT+MR-1+0.5mM AQS+3μM aniline", in which the Fe(II) production was significantly higher than that in the reaction groups of only microorganisms and no aniline reaction. The amount of Fe(II) produced was significantly higher than that of the microorganism-only and aniline-free reaction groups, and the addition of aniline also significantly increased the consumption of sodium lactate by MR-1 in the reaction system. The solid mineral Fe(II)-O content increased to 41.32% after the reaction. However, the structure of needle ferrite is relatively stable, and the surface morphology did not change significantly by SEM, and the generation of other secondary minerals was not observed in the XRD results. The results of this experimental study can help to understand the biogeochemical cycle of iron in multicomponent reactions and are of great significance for environmental management.

This study proposed a spatially and temporally improving methodology adopting the Regional Frequency Analysis with L-moments approach to estimate rainfall quantiles from 22787 grids of radar rainfall in Taiwan for a 24-hour duration. Due to limited radar coverage in the eastern region, significant discordant grids were found in the coastal area of the eastern region. A K-means cluster analysis using scaled at-site characteristics was used to group the QPESUMS grids in Taiwan into 22 clusters/sub-regions based on their characteristics. Spatially, homogeneous subregions with QPESUMS data produce more detailed homogeneous subregions with clear and continuous boundaries, especially in the mountain range area where the number of rain stations is still very limited. According to the results of z-values and L-moment ratio diagrams, the Wakeby (WAK), Generalized Extreme Value (GEV), and Generalized Pareto (GPA) distributions of rainfall extremes fitted well for the majority of subregions. The Wakeby distribution was the dominant best-fitted distribution, especially in the central and eastern regions. The east of the northern part and southern part of Taiwan had the highest extreme rainfall for each return period. Both areas were frequently struck by typhoons. By using grid-based (at-site) as the basis for assessing regional frequency analysis, the results show that the regional approach in determining extreme rainfall is very suitable for large-scale applications and even better for smaller scales such as watershed areas. The spatial investigation was performed by establishing regions of interest in small subregions across the northern part. It showed that regionalization was correct and consistent.

New antimicrobial approaches are essential to counter antimicrobial resistance. The drug development pipeline is exhausted with emergence of resistance resulting in unsuccessful trials. The lack of an effective drug developed from the conventional drug portfolio has mandated the introspection into the list of potentially effective unconventional alternate antimicrobial molecules. Alternate therapies, that are clinically explicable forms include monoclonal antibodies, antimicrobial peptides, aptamers and phages. Clinical diagnostics optimizes the drug delivery. In the era of diagnostic-based applications, it is logical to draw diagnostic based treatment for infectious diseases. Selection criteria of alternate therapeutics in infectious disease include detection, monitoring of response and resistance mechanism identification. Integrating these diagnostic applications is disruptive to the traditional therapeutic development. The challenges and mitigation methods need to be noted. Applying the goals of clinical pharmacokinetics that include enhancing efficacy and decreasing toxicity of drug therapy this review analyses the strong correlation of alternate antimicrobial therapeutics in infectious diseases. The relationship between drug concentration and the resulting effect defined by the pharmacodynamic parameters are also analyzed. This review analyzes the perspectives of aligning diagnostic initiatives into the use of alternate therapeutics with a particular focus on companion diagnostic applications in infectious diseases.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

Cholangiocarcinoma is the most common primary malignant tumor of the bile duct. The current standard first-line treatment for advanced or metastatic cholangiocarcinoma is gemcitabine and cisplatin. However, few effective treatment choices exist for refractory cholangiocarcinoma, and additional therapeutic drugs are urgently required. Our previous work demonstrated that the ALDH isoform 1A3 plays a vital role in the malignant behavior of cholangiocarcinoma and may serve as a new therapeutic target. In this study, we found a positive correlation between ALDH1A3 protein expression levels and cell migration abilities of three cholangiocarcinoma cell lines, which was verified using ALDH1A3-overexpressing and ALDH1A3-knockdown clones. We also used ALDH1A3-high and ALDH1A3-low populations of cholangiocarcinoma cell lines from the Library of Integrated Network-based Cellular Signatures (LINCS) program and assessed the effects of ruxolitinib, a commercially available JAK2 inhibitor. Ruxolitinib had a higher cytotoxic effect when combined with gemcitabine. Furthermore, the nuclear translocation STAT1 and STAT3 heterodimers were markedly diminished by ruxolitinib treatment, possibly resulting in decreased ALDH1A3 activation. Notably, ruxolitinib alone or combined with gemcitabine led to significantly reduced tumor size and weight. Collectively, our studies suggest that ruxolitinib might suppress the ALDH1A3 activation through the JAK2/STAT1/3 pathway in cholangiocarcinoma, and trials should be undertaken to evaluate its efficacy in clinical therapy.

While the global COVID-19 pandemic has been widely acknowledged to affect the mental health of health care workers (HCWs), attention to measures that protect those on the front lines of health outbreak response has been limited. In this cross-sectional study, we examine workplace contextual factors associated with how psychological distress was experienced in a South African setting where a severe first wave was being experienced with an objective of identifying factors that can protect against HCWs experiencing negative impacts. Consistent with mounting literature on mental health effects, we found a high degree of psychological distress (57.4% above General Health Questionnaire cut-off value) and a strong association between perceived risks associated with the presence of COVID-19 in the healthcare workplace and psychological distress (adjusted OR = 2.35, p <.01). Our research indicates that both training (adjusted OR 0.41, 95% CI 0.21 – 0.81) and the reported presence of supportive workplace relationships (adjusted OR 0.52, 95% CI 0.27 – 0.97) were associated with positive outcomes. This evidence that workplace resilience can be reinforced to better prepare for the onset of similar outbreaks in the future suggests that pursuit of further research into specific interventions to improve resilience is well merited.

Polycystic ovary syndrome (PCOS) is a common endocrine disorder in women, characterized by fluid-filled sacs in the ovaries and various symptoms including high androgen levels, endometrial irregularities, and cysts. While the cause of PCOS is unknown, it has been linked to genetic, endocrine, and metabolic factors, and there are several treatment options, including lifestyle modifications, medications, and surgery. Natural products, such as medicinal plants and fruits, are being explored as potential treatments for PCOS due to their bioactive compounds with pharmacological effects related to antioxidant, antimicrobial, anticancer, and antidiabetic properties. Some of these compounds improve insulin sensitivity, reduce inflammation, and enhance glucose metabolism, which is beneficial for women with PCOS. This review examined the effects of natural products on PCOS, including their effects on ovarian histological changes, blood glucose, sex hormones, and lipid profile, based on animal and human studies. This study suggests that the use of natural products as complementary medicine can be a promising resource for the development of effective therapeutics for PCOS, but that further research is needed to fully understand their benefits