Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

With the rapid development of wind power generations, the inertial response of wind turbines (WTs) are widely concerned recently, which is important for grid frequency dynamic and stability. This paper recognizes and understands the inertial response of type-3 and type-4 WTs from the view of equivalent internal voltage, in analogy with typical synchronous generators (SGs). Due to the dynamic of the equivalent inertial voltage different from SGs, the electromechanical inertia of WTs is completely hidden. The rapid power control loop and synchronization control loop is the main reasons that the WT's inertial response is disenabled. On the basis of the equivalent internal voltage's dynamic, the existing inertia control method for WTs are reviewed and summarized as three approaches from the view of WT's control, i.e. optimizing the power control or synchronization control or both. At last, the main challenges and issues of these inertia controls are attempted to explain and address.

This paper first discusses a fractional-order Liu system of order as low as 2.7 and shows its chaotic characteristics by carrying out numerical simulations such as Lyapunov exponents, bifurcation diagrams and phase portraits. Then, by using the topological horseshoe theory and computer-assisted proof, the existence of chaos in the system is verified theoretically. Finally, the fractional-order system is implemented on a Field Programmable Gate Array (FPGA) and the results obtained show that the fractional-order Liu system is indeed chaotic.

Typhoons bring great damages to transmission line systems located in coastal areas. Strong wind and extreme precipitation are the main sources of damaging effects. Transmission lines suffered from wind-driven rain exhibit more susceptibility to damage due to the coupled effect of wind and rain water. This paper presents an integrated numerical simulation framework based on mesoscale WRF model, multiphase CFD model and FEM model to analyze the motions of a transmission line subjected to coupled wind and rain loads during typhoon events. A full-scale transmission line in Zhoushan island is employed to demonstrate the effectiveness of the proposed framework by simulating typhoon evolution in terms of wind fields and rainfall, solving the coupled wind and rain fields around the conductor and predicting the dynamic responses of the transmission line during Super Typhoon Lekima (2019). The results show that the horizontal displacements of the transmission line under the joint actions of wind and rain increases approximately 17%~18% compared to those of wind loads only. It is important to consider the coupled effects of wind-driven rain on conductors in the design of transmission lines under typhoon conditions.

The genetic code evolved around the reading of the tRNA anticodon on the primitive ribosome, and tRNA-34 wobble and tRNA-37 modifications coevolved with the code. We posit that EF-Tu, the closing mechanism of the 30S ribosomal subunit, methylation of wobble U34 at the 5-carbon and suppression of wobbling at the tRNA-36 position were partly redundant and overlapping functions that coevolved to establish the code. The genetic code devolved in evolution of mitochondria to reduce the size of the tRNAome (all of the tRNAs of an organism or organelle). “Superwobbling” or four-way wobbling describes a major mechanism for shrinking the mitochondrial tRNAome. In superwobbling, unmodified wobble tRNA-U34 can recognize all four codon wobble bases (A, G, C and U), allowing a single unmodified tRNA-U34 to read a 4-codon box. During code evolution, to suppress superwobbling in 2-codon sectors, U34 modification by methylation at the 5-carbon position appears essential. As expected, at the base of code evolution, tRNA-37 modifications mostly related to the identity of the adjacent tRNA-36 base. TRNA-37 modifications help maintain the translation frame during elongation.

The genetic code evolved by parallel tracks of chaotic and ordered processes. Liquid-liquid phase separation (hydrogels), a chaotic process, constructs diverse membraneless compartments within cells, resulting in regulated hydration and sequestration and concentration of reaction components. Hydrogels relate to chaotic amyloid fiber production. We propose that polyglycine and related hydrogels (i.e. GADV; G is glycine), phase separations, membraneless droplets and amyloid accretions organized protocell domains to drive the earliest evolution of the genetic code and the pre-life to cellular life transition. By contrast, evolution of tRNA, tRNAomes, aminoacyl-tRNA synthetases and translation systems followed highly ordered and systematic pathways, described by well-defined mechanisms and rules. The pathway of evolution of aminoacyl-tRNA synthetases, which tracked evolution of the genetic code, is clarified. Hydrogels and amyloids form a chaotic component, therefore, that complemented otherwise systematic processes. We describe with detail a pre-life world in which hydrogels and amyloids provided the selections of the first life.

There are no theorems (proven theories) in the biological sciences. We propose that the 3 31 nt minihelix tRNA evolution theorem be universally accepted as one. The 3 31 nt minihelix theorem completely describes evolution of type I and type II tRNAs from ordered precursors (RNA repeats and inverted repeats). Despite diversification of tRNAome sequences, statistical tests overwhelmingly support the theorem. Furthermore, the theorem relates the dominant pathway for the origin of life on Earth, specifically, how tRNAomes and the genetic code may have coevolved. Alternate models for tRNA evolution (i.e., 2 minihelix, convergent and accretion models) are falsified. In the context of the pre-life world, tRNA was a molecule that via mutation could modify anticodon sequences and teach itself to code. We relate the clearest history to date of the chemical evolution of life on Earth. From analysis of tRNA evolution, ribozyme-mediated RNA ligation was a primary driving force in evolution of complexity during the pre-life to life transition on Earth.

A novel composite consisting of fluorine-doped carbon and graphene double-coated LiMn0.6Fe0.4PO4 (LMFP) nanorods, synthesized via a facile low temperature solvothermal method that employs a hybrid glucose and polyvinylidene fluoride as carbon and fluorine sources. As revealed by physicochemical characterization, F-doped carbon coating and graphene form a ‘point-to-surface’ conductive network, facilitating rapid electron transport and mitigating electrochemical polarization. Furthermore, the uniform thickness of the F-doped carbon coating alters the growth of nanoparticles and prevents direct contact between the material and the electrolyte, thereby enhancing structural stability. Strong electronegative F− is beneficial to inhibit the structural changes of LMFP caused by Li-insertion/extraction during charge/discharge, which effectively reduces the Jahn-Teller effect, and inhibits Mn dissolution. The distinctive architecture of LMFP/C-F/G cathode material exhibits excellent electrochemical properties, exhibiting an initial discharge capacity of 163.1 mAh g−1 at 0.1 C and a constant Coulombic efficiency of 99.7% over 100 cycles. Notably, LMFP/C-F/G cathode material achieves an impressive energy density of 607.6 Wh kg−1 , surpassing that of commercial counterparts. Moreover, it delivers a reversible capacity of 90.3 mAh g−1 at a high current rate of 5 C. The high-capacity capability and energy density of the prepared materials give them great potential for use in next-generation lithium-ion batteries.

Evolutionary, sequence and structural analyses of tRNA variable (V) loops provides a new understanding. Type I tRNA V loops have a primordial length of 5 nt, and type II tRNA V loops have a primordial length of 14 nt. Sequence-based alignments of type I and type II V loops gave deceptive results. Type II V loops are characterized by the trajectory of the V arm, the size and sequence of the loop and the first and last V loop nucleotides and their known contacts. Depending on the V arm trajectory, type II V stems and loops can be interaction sites for aminoacyl-tRNA synthetases. So, type II V arms for tRNALeu, tRNASer and tRNATyr (found in Bacteria) were coevolved and selected to distinguish determinants to support cognate tRNA charging. The alignment of type I and type II V loops was adjusted based on tRNA evolution. Results are consistent with Archaea being an older and simpler life form than Bacteria. TRNAome sequences were derived from radiation of an ordered tRNAPri (Pri for primordial) sequence comprised of known RNA repeats and inverted repeats. V loop and tRNA sequences, therefore, convey a history of the primary successful pathway in the origin of life.

The 20th century, global temperatures underwent significant changes, impacting agricultural climate zones worldwide. Xinjiang, China, a key player in machine-picked cotton production, was influenced by various heat-related indicators(sum of active temperature ≥ 10℃、mean temperature in July、climatological growing season length, April-May sum active temperature、Last spring frost, and Defoliator spray time). Using meteorological data from 58 weather stations in Xinjiang, we examined the spatio-temporal trends of these indicators during the period of 1981-2020. Additionally, we considered the effects of climate warming and plastic mulching on the sowing area and zoning area of machine-picked cotton in different suitable zones. Overall, Xinjiang experienced an trend in heat resources, with a pattern of "more in the southern part than the northern part, and more in plains and basins than in mountainous areas." Under climate warming conditions, the sowing area of the most suitable cotton zone and the suitable cotton zone has increased, while the sowing area of the moderately suitable cotton zone and unsuitable cotton zone has decreased. Under the plastic mulching mechanism, a comparison of the zoning area and sowing area from 1991 to 2020 revealed that there was no difference in the zoning area of the most suitable zone compared to the sowing area, while the zoning area of the suitable zone increased by 15.7% (2.15×103km2) compared to the sowing area. The zoning area of the moderately suitable zone decreased by 14.5% (0.26×103km2), and the unsuitable zone decreased by 7.8% (0.17×103km2) compared to their respective sowing areas. These results indicate that climate warming and plastic mulching have increased the cultivable area of machine-picked cotton in Xinjiang, but there are also instances of unreasonable zoning. It is necessary to allocate land resources reasonably based on climatic conditions to ensure the healthy development of the cotton industry in Xinjiang.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

This paper investigates the dynamic properties of artificial neural networks using differential equations and explores the influence of parameters on stability and neural oscillations. By analyzing the equilibrium point of the differential equations, we identify conditions for asymptotic stability and criteria for oscillation in artificial neural networks. Furthermore, we demonstrate how adjusting synaptic weights between neurons can effectively control stability and oscillation. The proposed model offers potential insights into the malfunctioning mechanisms of biological neural networks implicated in neurological disorders like Parkinson's disease tremors and epilepsy seizures, which are characterized by abnormal oscillations.

Gaze tracking of high-speed moving targets is a novel application mode for low Earth orbit microsatellites. In this mode, small satellites are equipped with high-resolution narrow-field-of-view video cameras for stable gaze-tracking imaging of high-speed moving targets. This paper proposes a high-precision attitude adaptive integral sliding mode control method with a feedforward compensation disturbance observer to enhance the capability of a microsatellite attitude control system for gaze tracking of high-speed moving targets. Specifically, first, we present the attitude control system model for microsatellites and the calculation method for the desired attitude of target tracking based on image feedback. Then, an adaptive integral sliding mode attitude control algorithm with a feedforward compensation disturbance observer, which meets the requirements of high-precision tracking control, is designed. The developed algorithm utilizes the disturbance observer to observe the friction torque of the flywheel and compensates for it through feedforward control. It also employs the adaptive integral sliding mode control algorithm to reduce the impact of uncertain disturbances, decrease the steady-state error of the system, and enhance the attitude control precision. Simulation experiments demonstrated that the designed disturbance observer can successfully observe the frictional disturbance torque of the flywheel. The attitude Euler angle control precision for high-speed moving target tracking reached 0.009°, and the angular velocity control precision reached 0.005°/s, validating the effectiveness of the proposed approach.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

Carrot juice and its associated beverage products are well-known healthy drinks all over the world. However, what effect carrot juice has on the human gut microbiota and how it is fermented by the intestinal microbes have not been studied. Here, using an in vitro model of anaerobic fermentation, we demonstrated that carrot juice could be fermented into lactate and acetate by the human gut microbiota. 16S high-throughput sequencing and bioinformatic analyses indicated that fermentation of carrot juice could significantly change the composition of the human gut microbiome. Interestingly, carrot juice remarkably increased the abundances of beneficial bacteria, including Lactobacillus fermentum, Lactobacillus salivarius, Lactobacillus mucosae and Bacteroides uniformis and decreased the population of opportunistic pathogenic bacteria, such as Enterococcus faecium in the gut. Collectively, our study illustrates a favorable effect of carrot juice on the human gut microbiota and lays a foundation for the development of carrot juice as a novel prebiotic agent.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

Decades of research identified numerous gene biomarkers of cardiac diseases whose restored sequence or/and expression level was hoped to recover the normal cardiac function. However, each human has unique and dynamic pathophysiological characteristics resulting from the unrepeatable combination of favoring factors such are: race, sex, age, medical history, diet, stress, exposure to toxins, habits etc. As such, no treatment fits everybody and finding personalized solutions is a top priority for medicine of 21st century. The Genomic Fabric Paradigm (GFP) provides the most theoretically possible comprehensive characterization of the transcriptome, its alterations in disease and recovery following a treatment. By attaching to each gene the independent average expression level, expression variation and expression coordination with each other gene, GFP delivers thousands times more information than the traditional analysis. This report presents the theoretical bases of the GFP and some applications to our microarray data from mouse models of post ischemic, and constant and intermittent hypoxia-induced heart failure. The GFP analyses revealed novel transcriptomic aspects of the gene expression control and networking under ischemic conditions. Through all-inclusive characterization of the transcriptome and the unrepeatable gene hierarchy in each condition, GFP is an essential avenue towards development of a truly personalized cardiogenomic therapy.

The intricate relationship between physical and social environments within organizations plays a pivotal role in shaping sustainable innovation endeavors. This paper presents a comprehensive analysis of two key dynamics that have garnered substantial scholarly attention for promoting sustainable innovation: the physical environment and the organizational climate. To elucidate the intricate interplay between these dynamics, we propose a novel three-dimensional framework that guides the modeling of the intricate processes through which the physical environment and innovation climate synergistically influence innovation outcomes. Building on this framework, we delve into an in-depth literature review concerning physical environments that exert a significant impact on innovation. Through this review, we identify and elaborate on four pivotal elements of the physical environment: communality, personalization, comfort, and healthiness. Leveraging insights gleaned from this review, we outline two promising avenues for future research in the realm of the physical environment's interaction with the innovation climate. Furthermore, we underscore the critical importance of adopting an interdisciplinary approach that seamlessly integrates insights from both the physical and social domains to comprehensively understand the sustainable innovation landscape.

Evodiamine is a bioactive alkaloid that is specified as a biomarker for the quality assessment of Evodia rutaecarpa and for traditional Chinese medicines containing this plant. We previously reported that quantitative structure-activity modeling indicated that evodiamine may cause cardiotoxicity. However, previous investigations have indicated that evodiamine has beneficial effects in patients with cardiovascular diseases and there are no previous in vitro or in vivo reports of evodiamine-induced cardiotoxicity. The present study investigated the effects of evodiamine on primary cultured neonatal rat cardiomyocytes in vitro, and on zebrafish in vivo. Cell viability was reduced in vitro, where evodiamine had a 24-h 50% inhibitory concentration of 28.44 µg/mL. Cells exposed to evodiamine also showed increased lactate dehydrogenase release and maleic dialdehyde levels, and reduced superoxide dismutase activity. In vivo, evodiamine had a 10% lethal concentration of 354 ng/mL and induced cardiac malfunction, as evidenced by changes in heart rate and circulation, and pericardial malformations. This study indicated that evodiamine could cause cardiovascular side effects involving oxidative stress. These findings suggest that cardiac function should be monitored in patients receiving preparations containing evodiamine.

The root system plays an irreplaceable role in plant growth. Its improvement can increase crop productivity. However, such system is still mysterious for us. The underlying mechanism has not been fully uncovered. The investigation on proteins related to the root system is an important means to complete this task. In the previous time, lack of root-related proteins makes it impossible to adopt machine learning methods for designing efficient models for the discovery of novel root-related proteins. Recently, a public database on root-related proteins was set up and machine learning methods can be applied in this field. In this study, we proposed a machine learning based model, named Graph-Root, for identification of root-related proteins. The features derived from protein sequences and one network were extracted, where the former features were processed by graph convolutional neural network and multi-head attention, and the later features abstracted the linkage between proteins. These features were fed into the fully connected layer to make prediction. The 5-fold cross-validation and independent tests suggested its good performance. It also outperformed the only one previous model, SVM-Root. Furthermore, the importance of each feature type and component in the proposed model was investigated.

The mangrove plant Acanthus ilicifolius and its relative, A. mollis, have been previously proved to possess diverse pharmacological effects. Therefore, evaluating the differentially expressed proteins of these species under tidal flooding stress is essential to fully exploit and benefit from their medicinal values. The roots of A. ilicifolius and A. mollis were exposed to 6 h of flooding stress per day for 10 days. The dry weight, hydrogen peroxide (H2O2) content, anatomical characteristics, carbon and energy levels, and two-dimensional electrophoresis coupled with MALDI-TOF/TOF MS technology were used to reveal the divergent flooding resistant strategies. A. ilicifolius performed better under tidal flooding stress, which was reflected in the integrity of the morphological structure, more efficient use of carbon and energy, and a higher percentage of up-regulated proteins associated with carbon and energy metabolism. A. mollis could not survive in flooding conditions for a long time, as revealed by incomplete cell structures of the roots, less efficient use of carbon and energy, and a higher percentage of down-regulated proteins associated with carbon and energy metabolism. Energy provision and flux balance played a role in the flooding tolerance of A. ilicifolius and A. mollis.

The molecular clusters ((HO)3Si-O-Si(OH)3, and (HO)3Al-O-Si(OH)3 ) representative of aluminosilicate mineral surface were employed to study the dissolution of aluminosilicate in acidic condition via density functional theory with the M06-2X+G(d,p) methodology. The surface termination sites (Si and Al) were both tetra-coordinated and the terminal oxygen was protonated in acidic condition. In the dissolution reaction, the calculated barrier height of the six-membered ring transition state complex containing two water molecules was predicted to be lower than that of four-membered ring transition state complex containing one water molecule. In addition, the calculated barrier heights for Al-terminated sites were predicted to be lower than those for the Si-terminated sites, suggesting that breaking the Al-O bond is easier than Si-O bond in the aluminosilicate mineral surface; the barrier heights of the surface termination sites with protonated terminal oxygen were lower than those without protonated terminal oxygen. With the fracture of Si-O and Al-O bonds, the Si and Al release from the aluminosilicate. These results confirm the experimental conclusions that the acidic condition facilitates the release of Si and Al from the aluminosilicate, and the concentration of Al leaching from aluminosilicate is higher than Si.

This paper presents ConF, a novel deep learning model designed for accurate and efficient prediction of non-coding RNA families. NcRNAs are essential functional RNA molecules involved in various cellular processes, including replication, transcription, and gene expression. Identifying ncRNA families is crucial for comprehensive RNA research, as ncRNAs within the same family often exhibit similar functionalities. Traditional experimental methods for identifying ncRNA fam-ilies are time-consuming and labor-intensive. Computational approaches relying on annotated secondary structure data face limitations in handling complex structures like pseudoknots and have restricted applicability, resulting in suboptimal prediction performance. To overcome these chal-lenges, ConF integrates mainstream techniques such as residual networks with dilated convolutions and cross multi-head attention mechanisms. By employing a combination of dual-layer convolu-tional networks and BiLSTM, ConF effectively captures intricate features embedded within RNA sequences. This feature extraction process leads to significantly improved prediction accuracy compared to existing methods. Experimental evaluations conducted on a ten-fold publicly available dataset demonstrate the superiority of ConF in terms of accuracy, sensitivity, and other perfor-mance metrics. Overall, ConF represents a promising solution for accurate and efficient ncRNA family prediction, addressing the limitations of traditional experimental and computational methods.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

Types of DNA recombination include homologous recombination and nonhomologous recombination. Homologous DNA recombination is a general term that includes exchange of information between chromatids: (reciprocal) crossing-over, gene conversion, and post-meiotic segregation. Gene conversion is now thought to be a type of non-Mendelian segregation of heterozygous markers near the recombination initiation site. Thus, it includes both gene conversion and post-meiotic segregation previously described. DNA non-HR including transpositional recombination and site-specific recombination. Our understanding of the molecular mechanism by which DNA recombination occurs has significantly increased in the past decades. Currently The synthesis-dependent strand annealing model is now thought to give rise to most or all noncrossovers, with the double-strand-break repair model forming mainly crossovers. The Shapiro model proposed by Dr. J. Shapiro explains the molecular mechanism of transpositional recombination. Site-specific recombination results from another distinct model. We previously proposed a novel theory which can provide a more reasonable and simpler explanation accounting for DNA HR including the 3 classes of recombinogenic events described above. In the new supplementedly molecular model, DNA meiotic recombination can be initiated by a copy choice mechanism, that is, copying part of 1 single-stranded DNA template, followed by DNA polymerase switching to another single-stranded DNA template, and then resuming the following DNA synthesis along the new template. The current review suggests that transpositional recombination and site-specific recombination should be initiated by copy choice during DNA synthesis rather than break/join mechanism. The work indicates that review of DNA nonhomologous recombination are very necessary. The novel theory would challenge earlier models accounting for transpositional recombination and site-specific recombination and would be critical to the understanding of the mechanisms. We hope copy choice initiating DNA nonhomologous recombination will be one of the concepts that are explored. Proper and specific experiments are required to reconstruct the detailed mechanism described here.

Sea cucumber detection represents a significate step in underwater environmental perception, which is an indispensable part of the intelligent subsea fishing system. However, various complex factors such as water turbidity declines the clarity of underwater images, presenting a challenge to vision-based underwater target detection. Therefore, accurate, real-time and lightweight detection models are required. First of all, the development of subsea target detection is summarized in this presented work. Besides, since target detection methods based on deep learning such as YOLOv5 and DETR, which are respectively examples of one-stage and anchor-free deep leaning methods, have been increasingly applied in underwater detection scenarios. Based on the analysis of state-of-the-art underwater sea cucumber detection approaches and aiming to provide a reference for practical subsea identification, the sea cucumber detection based on the YOLOv5 and DETR are investigated and compared in detail. For each approach, the detection experiment is carried out on the derived dataset which contains a wide variety of sea cucumber sample images. The compared experiments demonstrate that the overall outperformance of YOLOv5 in terms of low computing consumption and high precision, particularly in detection of small and dense features. Nevertheless, the DETR exhibits rapid development and holds promising prospects in underwater object detection applications, owing to its relatively simple architecture and ingenious attention mechanism.

Polyacetylene phytochemicals are emerging as potentially responsible for the chemoprotective effects of consuming apiaceous vegetables. There is some evidence suggesting that polyacetylenes impact carcinogenesis by influencing a wide variety of signalling pathways, which are important in regulating inflammation, apoptosis, cell cycle regulation, etc. Studies have shown a correlation between human dietary intake of polyacetylene-rich vegetables with reduced risk of inflammation and cancer. Polyacetylene supplementation can influence cell growth, gene expression, and immunological responses, and reduce tumour number in rat and mouse models. Cancer chemoprevention by dietary polyacetylenes involves several mechanisms, including effects on inflammatory cytokines, the NF-κB pathway, antioxidant response elements, UPR pathway, growth factor signalling, cell cycle progression, and apoptosis. This review summarises the published research on falcarinol-type polyacetylene compounds and their mechanisms of action regarding cancer chemoprevention and treatment, and also identifies some gaps in our current understanding of the health benefits of these polyacetylenes.

With the development of society and the economy, the unified planning of architectural style has become a difficult problem in the competition between urban expansion and the protection of tra-ditional buildings in villages and towns. At the same time, it also allows people to re-examine the appearance and quality of life of traditional village buildings. In this paper, the Conditional Gen-erative Adversarial Network (CGAN) is used to construct a method of building facade generation in villages and towns, so as to gradually realize the governance of the style of villages and towns. At the same time, it has also reduced the restoration of the facades of villages and towns and the graphic design of rural tourism products, showing its application value and potential in the field of planning and design. In the research, taking villages and towns in the Wuyishan area of China as an example, the method is used to carry out model training, image generation, and comparison of the derivation results of different assumed building contours and product contours. The research shows that: (1) CGAN can be used to derive and design the facades of conventional civil buildings in villages and towns. (2) In terms of product graphic design, especially the common tourist cultural products fans and water cups, show significant potential. (3) The construction of this method is not only applicable to villages and towns under the World Heritage City, but can be further promoted and used in the future for cities and villages that have a demand for architectural style consistency.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

Disparities between fold amplitude (A) and intrusion thickness (Hsill) are critical in identifying elastic or inelastic deformation in a forced fold. However, accurate measurement of these two parameters is challenging because of the limit in separability and detectability for the seismic data. In the TZ-47 exploring area from the Tarim Basin, Northwest China, we combined wireline data and 3-D seismic data, to accurately constrain the fold amplitude and total thickness of sills that inducing the roof uplift. The measurement results show that the forced fold amplitude is 155 m and the total sill thickness is 148.4 m. When using a magma density of 2.7 g/cm3, and solid rock density of 3 g/cm3, the molten magma thickness at the time of intrusion would be 153.8 m, which is almost no difference from the forced fold amplitude. Therefore, the TZ-47 fold is a pure elastic forced fold induced by emplacement of multiple sills. Measurement solely based on seismic data may not be able to detect some thin interlayers and may result in large errors.

The real systems are often complex, nonlinear, and noisy in various areas including mathematics, natural science, and social science. We present the symplectic entropy (SymEn) measure as well as an analysis method based on SymEn to estimate the nonlinearity of the complex system by analyzing the given time series. The SymEn estimation is a kind of entropy based on symplectic principal component analysis (SPCA) which represent organized but unpredictable behaviors of systems. The key to SPCA is to preserve the global submanifold geometrical properties of the systems through symplectic transform in the phase space, which is a kind of the measure-preserving transforms. The capability of preserving the global geometrical characteristics makes the SymEn a test statistic to detect the nonlinear characteristics in several typical chaotic time series and the stochastic characteristic in the Gaussian white noise. The results are in agreement with findings in the approximate entropy (ApEn), the sample entropy (SampEn) and the fuzzy entropy (FuzzyEn). Moreover, the SymEn method is also used to analyze the nonlinearities of the real signals (including the EEG signals for ASD and healthy subjects, and the sound and vibration signals for the mechanical systems). The results indicate that the SymEn estimation can be taken as a measure for describing the nonlinear characteristics in the data collected from the natural complex systems.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

Magnetometric Resistivity(MMR) Method, which can use the power supply method of the traditional apparent resistivity method to measure the magnetic field. At present, the application research abroad is relatively extensive, but the domestic(China) research on the application of the MMR method is very few, and it is not even well-known. This paper is based on the MMR theoretical method under the point source DC condition, combined with the abnormal potential method and the modified Biot-Savart law, and using the three-dimensional numerical calculation method of the finite difference method to calculate the abnormal potential field, electric field, and magnetic field on the matlab2018a platform. Calculate, realize the multi-physics simulation in the electromagnetic field through Matlab platform programming, and verify the correctness of the algorithm by the spherical anomaly model with an analytical solution. Through the visual simulation of the three-dimensional data volume of the multi-physics field in the electromagnetic field, we can better understand the response mechanism of the electromagnetic field under DC conditions and grasp their three-dimensional spatial distribution rules. It is hoped that the research in this article can help the research of MMR Personnel better use this method for exploration.

Intergenerational integration has given rise to a novel aging paradigm known as all-age communities, which is garnering international attention. In China, the aging population and the implementation of the three-child policy have resulted in increased demand for retirement and childcare services among residents in older neighborhoods. Consequently, there is a pressing need to retrofit these older neighborhoods to accommodate all-age living arrangements given the high demand they generate. Therefore, this study undertakes research interviews with residents and constructs an exploratory theoretical model rooted in established theory. To assess the significance of our model, we employ Smart PLS 3.0 based on 297 empirical data points. Our findings indicate that anxiety has a significant negative effect on payment behavior; objective perception, willingness to pay, and government assistance exert significant positive effects on payment behavior. By comprehensively analyzing the mechanisms underlying residents’ payment behavior, this study provides valuable insights to the government for promoting the aging process within communities and formulating effective transformation policies.

Today, the digital economy has pursued the required social and economic development, and enterprises can achieve long-term sustainability by relying on the digital platform ecosystem. However, the development of the digital economy and the rapid growth of platform ecosystems have also generated some problems. To study effective digital platform ecosystem governance, this study used the tripartite evolutionary game method and analyzed the changes and effects of platform regulation under different development stages from the perspectives of government, platforms, and enterprises. The results indicate that in the early stages, digital platforms primarily relied on the government’s obligation to regulate. With the digital platform ecosystem’s evolution, the platform organization and settled enterprises’ governance effects gradually appeared, establishing the three common constraints of governance mode. Finally, when the digital platform ecosystem is in its self-renewal period, the government effect is reduced, with the platform itself and settled enterprises taking primary supervisory roles. This study provides reasonable methods for effective platform governance at different stages and enriches the theoretical basis and management practices of platform ecosystems.

Existing one-shot neural architecture search (NAS) methods have to conduct a search over a giant super-net, which leads to the huge computational cost. To reduce such cost, in this paper, we propose a method, called FTSO, to divide the whole architecture search into two sub-steps. Specifically, in the first step, we only search for the topology, and in the second step, we search for the operators. FTSO not only reduces NAS’s search time from days to 0.68 seconds, but also significantly improves the found architecture's accuracy. Our extensive experiments on ImageNet show that within 18 seconds, FTSO can achieve a 76.4% testing accuracy, 1.5% higher than the SOTA, PC-DARTS. In addition, FTSO can reach a 97.77% testing accuracy, 0.27% higher than the SOTA, with nearly 100% (99.8%) search time saved, when searching on CIFAR10.

With the rapid development of network science, Turing pattern on complex networks has attracted extensive attention from researchers. In this paper, we focus on spatial patterns in multiplex ER (Erdös-Rényi) random networks, taking the predator-prey model with Allee effect and hyperbolic mortality as an example. In theory, the threshold condition for generating Turing pattern is given using the Turing instability theory of multiplex networks. Numerically, we design relevant experiments to explore the impact of network topology on Turing pattern. The factors considered include model parameters, diffusion rate, average degree of the network, and differences in the average degree of different layers. The results indicate that the importance of diffusion rate and network average degree for Turing pattern is affirmed on the single-layer network. For multiplex networks, the differentiation of average degrees in different layers controls the generation of Turing pattern, which is not affected by the diffusion rates of the two populations. More interestingly, we observe the switching of Turing pattern and spatiotemporal pattern. We believe that these findings contribute to a better understanding of self-organization on complex networks.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

Land use is an embodiment of human socioeconomic activities and represents a bridge between these activities and natural systems. Through social activities, humans transform land use to promote social and economic development and improve production, living conditions, and eco-logical functions of land. Rural residential land represents a space for rural residents to reside in and exhibits spatial characteristics that evolve over time, which is proof of rural socioeconomic development. This paper observes rural residential land in 21 cities on the Grand Canal and analyses its spatial differentiation. Then, it explores the driving factors of this land using spatial grid analysis and the geographic detector model. Lastly, it proposes three different forms of rural residential land based on the results. The study found that: (1) the change of rural residential land in the northern part of the Grand Canal was more volatile than that in the southern part. The change of rural residential land from 1990 to 2020 conformed to the pattern of cultivated land - rural residential land - urban construction land; (2) Based on the driving factors of rural residen-tial land, the land is divided into one-dimensional cities, two-dimensional cities and three-dimensional cities. Circular, linear, and scattered cities of different sizes were affected by socioeconomic factors, transportation accessibility, and the natural environment, respectively; and (3) Finally, according to the spatial differentiation characteristics and the driving factors of rural residential land, the study proposes the construction of three types of villages through the strate-gies of constructing large-scale villages, relocating and reconstructing new villages, and con-structing high-quality villages, respectively. Enhancing the scientific planning of rural residential land and its efficiency can offer the protection of agricultural land and the integration of urban and rural areas in the new era.

Failure characteristics induced by unloading disturbance and the corresponding mechanical mechanism of the coal seam floor are important theoretical bases for water-bursting prevention from the floor of the coal seam and rock burst alarm in deep mining. However, the existing two-dimensional ground-pressure-control theory based on shallow mining cannot sufficiently guide deep-mining practices. In this study, the redistribution of mining-induced stress field in rocks surrounding the longwall face and mechanical behaviors of strata in deep mining are investigated through a combination of numerical simulation, physical simulation, and field measurement. Results demonstrate that mining-induced stress fields in the floor of the longwall face differ in space and time. Vertical stress unloading from top to bottom of the floor and horizontal stress unloading are relatively low. A concentration zone of high horizontal stress exists at stope boundaries. The critical yield load of rock stratum in the floor is determined through thin plate yield theory. Under the combined effect of concentrated high horizontal and vertical resilience stresses, strata in the floor fracture from seam to seam if the load increases to the minimum critical buckling value. Fractured strata slide along the fracture surface, which leads to floor heave. The stope floor shows evident time-delay progressive failure characteristics. The stress shell in the stope floor in deep mining is found to be a sensitive mechanical parameter that produces three-dimensional ground-pressure behavior in the floor. This ground-pressure behavior in the stope floor is controlled by the existence of the corresponding stress shell and effects induced by its space–time evolution. This study provides theoretical basis for the dynamic control of a hazard-inducing environment in engineering and minimizing or altering disaster-occurrence conditions during the construction engineering of the coal seam floor.

Sign language recognition is essential in hearing-impaired people’s communication. Sign language recognition is an important concern in computer vision and has been developed with rapid progress in image recognition technology. However, sign language recognition using a general monocular camera has problems with occlusion and recognition accuracy in sign language recognition. In this research, we aim to improve accuracy by using a 2-axis bending sensor as an aid in addition to image recognition. We aim to achieve higher recognition accuracy by acquiring hand keypoint information of sign language actions captured by a monocular RGB camera and adding sensor assist. To improve sign language recognition, we need to propose new AI models. In addition, the amount of dataset is small because it uses the original data set of our laboratory. To learn using sensor data and image data, we used MediaPipe, CNN, and BiLSTM to perform sign language recognition. MediaPipe is a method for estimating the skeleton of the hand and face provided by Google. In addition, CNN is a method that can learn spatial information, and BiLSTM can learn time series data. Combining the CNN and BiLSTM methods yields higher recognition accuracy. We will use these techniques to learn hand skeletal information and sensor data. Additionally, the 2-axis Bending sensor glove data support training AI model. Using these methods, we aim to improve the recognition accuracy of sign language recognition by combining sensor data and hand skeleton data. Our method performed better than using skeletal information, achieving 96.5% accuracy in Top-1.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

Coronavirus disease 2019 (COVID-19) is caused by infection with the 2019 novel coronavirus 2 (2019-nCoV, now referred to as SARS-CoV-2). COVID-19 has become a global pandemic since its outbreak at the end of Dec 2019. COVID-19 could lead to severe acute respiratory disease, especially to those who have reduced immunity. Binding of the viral Spike protein (S) to its receptor ACE2 (Angiotensin Converting Enzyme 2) on the surface of target cells has been proven to be key for virus entry and infection. Although ACE2 expression in the respiratory system is necessary for pneumonia infection by SARS-CoV-2, the regulation of ACE2 gene expression remains poorly investigated, especially for patients that are in pre-pathological conditions. Here, by analyzing The Gene Expression Omnibus (GEO) database, we investigated the expression regulation of ACE2 in various kinds of primary epithelial cells from the respiratory system after varies of respiratory viruses infection such as influenza A virus (IFV), respiratory syncytial virus (RSV) and human rhinovirus (hRV). Our analyses reveal that infection of multiple kinds of respiratory viruses or influenza vaccines greatly increased ACE2 expression, suggesting that respiratory viruses infection could represent a high risk factor for developing COVID-19. We also found that the regulatory effect of influenza A virus on ACE2 expression is associated with activation of the interferon beta-induced pathway and viral RNA-activated host response. Together, our data provide a theoretical framework for clinical classification for SARS-CoV-2 infection susceptibility and could be used for future prevention and therapy treatment for COVID-19.

The emergence of Artificial Intelligence (AI) driven Keyword Spotting (KWS) technologies has revolutionized human to machine interaction. Yet, the challenge of end-to-end energy efficiency, memory footprint and system complexity of current Neural Network (NN) powered AI-KWS pipelines has remained ever present. This paper evaluates KWS utilizing a learning automata powered machine learning algorithm called the Tsetlin Machine (TM). Through significant reduction in parameter requirements and choosing logic over arithmetic based processing, the TM offers new opportunities for low-power KWS while maintaining high learning efficacy. In this paper we explore a TM based keyword spotting (KWS) pipeline to demonstrate low complexity with faster rate of convergence compared to NNs. Further, we investigate the scalability with increasing keywords and explore the potential for enabling low-power on-chip KWS.

Urban planning and transportation policies are vital to creating sustainable and liveable cities. Transit-orientated development (TOD) has emerged as a prominent approach, emphasising the establishment of neighbourhoods with convenient access to public transportation and promoting car-free lifestyles. TOD initiatives aim to improve public transit efficiency, reduce dependence on private vehicles, and encourage walkability and connectivity within communities. By prioritising TOD, cities can effectively address transportation challenges, alleviate congestion, mitigate carbon emissions, and improve residents' overall quality of life. This research paper investigates the connection between proximity to transit stations and local living habits. Specifically, it examines the human mobility of residents living within a 15-minute walk distance of transit stations in Auckland, New Zealand, a car-dependent city striving to transition into a sustainable TOD model. The objective is to determine whether people living near transit stations are more inclined to participate in local activities and exhibit a higher proportion of trips within a radius of 15 minutes. The results illustrate that approximately 54% of the residents show dominant local mobility patterns. However, only about 16 stations out of 34 show their local residents have prominent collective 'local' travel patterns. By understanding the connection between proximity to transit stations and local mobility patterns, urban planners and designers can make informed decisions to improve the built environment and optimise the land use mix. This research offers insights to support the creation of vibrant and people-centric urban environments, facilitating the development of sustainable and liveable cities.

Individual users' payment behaviors have changed. The diffusion of mobile devices makes people suitable for proximity mobile payment (PMP) services without the need for traditional payment. Existing mobile payment literature mainly focuses on users' adoption and continuous usage behavior, nevertheless, switching behavior on payment received little attention, especially focusing on why users switch from traditional payment to PMP. Thus, the objective of the current research is to investigate factors influencing users’ traditional payment - PMP switching to comprehend how these factors shape users’ switching intentions. We developed a traditional payment - PMP transition model based on the push-pull-mooring framework derived from migration theory. This research adopted a structural equation modeling analysis on 311 valid data. The findings indicate that a push factor drives users away from traditional payment in terms of dissatisfaction. The pull factors, including perceived substitutability and perceived usefulness, attract users to PMP. Furthermore, in terms of perceived technical compatibility, a positive mooring factor facilitates users' switching to PMP. The negative mooring factor, in terms of perceived risk, hinder users' switching intention. However, another pull factor - perceived ease of use, failed to influence switching intention significantly. This study found some distinctions between mobile payment switching and mobile payment adoption. These findings provide pivotal insights for mobile payment service providers.

To predict the remaining useful life (RUL) of proton exchange membrane fuel cell (PEMFC) in advance, a prediction method based on the voltage recovery model and Bayesian optimization of a multi-kernel relevance vector machine (MK-RVM) is proposed in this paper. First, the empirical mode decomposition (EMD) method was used to preprocess the data, and then the MK-RVM was used to train the model. Then, the Bayesian optimization algorithm was used to optimize the weight coefficient of the kernel function to complete the parameter update of the prediction model, and the voltage recovery model was added to the prediction model to realize the rapid and accurate prediction of the RUL of PEMFC. Finally, the method proposed in this paper was applied to the open data set of PEMFC provided by FCLAB, and the prediction accuracy of the RUL of PEMFC was obtained by 95.35%, which showed that the method had good gen-eralization ability and verified the accuracy of the prediction for the RUL of PEMFC.

A number of challenging combinatorial optimization problems in logistics, transportations, aeronautics, and astronautics can be modeled as orienteering problems (OPs). To address the classic OP and its real-world variants, a parallel adaptive local-search algorithm based on competition and evolution (Palace) is proposed in this paper. In this algorithm, the parallelism runs proper local-search metaheuristics and operators to obtain the population per generation; then the competition grades those metaheuristics and operators to highlight the outperforming and eliminate the underperforming; also, the evolution explores large solution space and reproduces the best solutions for next generation. In this manner, the parallelism, competition, and evolution are organized in an easy-to-use algorithm and enable the expansibility, adaptivity, and exploration abilities, respectively. The Palace is examined on the classic and real-world Benchmarks about the OP, the time-dependent/independent OP with time windows, and the unmanned aerial vehicle and agile earth observation satellite planning. As a result, the Palace shows good performance in applicability and effectiveness in comparison with the state-of-the-art algorithms.

The event camera generates an event stream based on changes in brightness, retaining only the characteristics of moving objects, addresses the high power consumption associated with using high-frame-rate cameras for high-speed eye tracking tasks. However, the asynchronous incremental nature of event camera output has not been fully utilized, and there are also issues related to missing event datasets. Combining the temporal information encoding and state-preserving properties of spiking neural network (SNN) with event camera, a near-range eye tracking algorithm is proposed as well as a novel event-based dataset for validation and evaluation. According to experimental results, the proposed solution outperforms artificial neural network (ANN) algorithms, while computational time remains only 12.5\% of that of traditional SNN algorithms. Furthermore, the proposed algorithm allows for self-adjustment of time resolution, with a maximum achievable resolution of 0.081ms, enhancing tracking stability while maintaining accuracy.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

The condensing heat exchanger is commonly applied in various heat exchange systems. It can efficiently recover moisture and heat from the flue gas that contains water vapor. However, the convective-condensation heat transfer process is so complicated that no mature thermal calculation model is available. This study develops a thermal calculation model for the widely employed tubular condensing heat exchanger in industry. To characterize the degree of the heat and mass transfer, this study introduces two parameters, namely the sensible and latent heat transfer efficiencies of fin. The thermal calculations are conducted for the condensing heat exchangers reported in the literature to verify the proposed model by comparing it with the experimental data. The results show that the absolute error of the calculated sensible and latent heat transfer efficiencies is 0.0365 and 0.0268, respectively. Under the working conditions in this study, a maximum difference of 5.2 K has been acquired between the measured and calculated values of the outlet temperature. The relative error of the condensate water flowrate is mostly within ±5.0% and ±10.0% under the bare-tube and finned-tube conditions, respectively, with a maximum deviation of 0.7 and 1.4 kg h-1. This study provides a general model for designing and optimizing various tubular condensing heat exchangers accurately.

Hyperspectral image and LiDAR image fusion plays a crucial role in remote sensing by capturing spatial relationships and modeling semantic information for accurate classification and recognition. However, existing methods, like Graph Convolutional Networks (GCNs), face challenges in constructing effective graph structures due to variations in local semantic information and limited receptiveness to large-scale contextual structures. To overcome these limitations, we proposed a invariant attribute-driven binary bi-branch classification (IABC) method which is a unified network that combines binary Convolutional Neural Network (CNN) and GCN with invariant attributes. Our approach utilizes a joint detection framework that can simultaneously learn features from small-scale regular regions and large-scale irregular regions, resulting in an enhanced structured representation of HSI and LiDAR images in the spectral-spatial domain. This approach not only improves the accuracy of classification and recognition but also reduces storage requirements and enables real-time decision-making, which is crucial for effectively processing large-scale remote sensing data. Extensive experiments demonstrates the superior performance of our proposed method in hyperspectral image analysis tasks. The combination of CNNs and GCNs allows for accurate modeling of spatial relationships and effective construction of graph structures. Furthermore, the integration of binary quantization enhances computational efficiency, enabling real-time processing of large-scale data. Therefore, our approach presents a promising opportunity for advancing remote sensing applications using deep learning techniques.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2>CH4>N2.

Activated carbon (AC) is an effective adsorbent for creatinine removal in hemoperfusion. However, the hemocompatibility and adsorption capacity of AC was required to be improved furthermore. Heparin, a widely used anticoagulant biomacromolecule, could improve the hemocompatibility of the absorbents in different ways based on its molecular weight. Thus, it was necessary to study the surface modification with unfractionated heparin (UFH) or low molecular weight heparin (LMWH) on improvement of hemocompatibility and adsorption. In this study, UFH and LMWH were respectively grafted on AC through polyethyleneimine as an intermediate layer. The modification of AC about morphology, mechanical strength and pore structure was characterized by XPS, SEM, TA and BET. It was found that compared with AC, the morphology and mechanical strength AC-UFH and AC-LMWH could be well maintained, but the BET surface was decreased due to the grafting of macromolecules. Furthermore, AC-UFH and AC-LMWH showed the better hemocompatibility on protein adsorption, APTT and platelet activation compared with AC, in which AC-LMWH had lower fibrinogen adsorption and longer APTT than AC-UFH. Besides, it was found that AC, AC-UFH and AC-LMWH had no significant effect on blood cell composition. Finally, the adsorption capacity of adsorbents for creatinine was evaluated. Although there was no significant difference between AC-UFH and AC-LMWH, it was found that heparin could be interacted with creatinine to enhance the adsorption capacity when compared with AC-PEI. This study deepened the understanding of anticoagulation of heparinized surface and provided a theoretical basis for adsorbents in hemoperfusion.

Modern war is sudden and rapid, and once the battle starts, the demand for equipment maintenance and guarantee will show an outburst situation, which puts equipment maintenance and guarantee capability to a severe test. To accurately grasp the civil-military integration of aviation maintenance and guarantee capabilities, it is necessary to evaluate their capabilities. To this end, the evaluation indicator system is established by using the three-dimensional indicator system construction model of "maintenance task → task demand → capability demand", and the evaluation method based on intuitionistic fuzzy entropy and normal grey cloud model is proposed, using intuitionistic fuzzy entropy theory to determine the expert weights and indicator weights, and the grey cloud model theory to determine the capability evaluation level. Finally, the application process of the evaluation model is demonstrated through specific examples, and the evaluation results are analyzed to verify the effectiveness of the evaluation model.

Modern war is sudden and rapid, and once the battle starts, the demand for equipment maintenance and guarantee will show an outburst situation, which puts equipment maintenance and guarantee capability to a severe test. To accurately grasp the civil-military integration of aviation maintenance and guarantee capabilities, it is necessary to evaluate their capabilities. To this end, the evaluation indicator system is established by using the three-dimensional indicator system construction model of "maintenance task → task demand → capability demand", and the evaluation method based on intuitionistic fuzzy entropy and normal grey cloud model is proposed, using intuitionistic fuzzy entropy theory to determine the expert weights and indicator weights, and the grey cloud model theory to determine the capability evaluation level. Finally, the application process of the evaluation model is demonstrated through specific examples, and the evaluation results are analyzed to verify the effectiveness of the evaluation model.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

The connexin gene family is the most prevalent gene that contributes to hearing loss. Connexins 26 and 30, encoded by GJB2 and GJB6 respectively, are the most abundant expressed connexins in the inner ear. Connexin 43 which is encoded by GJA1 appears to be widely expressed in various organs, including the heart, skin, brain, and inner ear. The mutations that arise in GJB2, GJB6 and GJA1 can all result in comprehensive or non-comprehensive genetic deafness in newborns. As it is predicted that connexins include at least 20 isoforms in humans, the biosynthesis, structural composition, and degradation of connexins must be precisely regulated so that the gap junctions can operate properly. Certain mutations result in connexins possessing a faulty subcellular localization, failing to transport to the cell membrane and preventing gap junction formation, ultimately leading to connexin dysfunction and hearing loss. In this review, we provide a discussion of the transport models for connexin 43, connexins 30 and 26, mutations affecting trafficking pathways of connexin 26, the existing controversies in trafficking pathways of connexins, and the molecules involved in connexin trafficking and their functions. This review can contribute to a new way of understanding the etiological principles of connexin mutations and finding therapeutic strategies for hereditary deafness.

Mississippi youth are demographically unique compared to that of the nation. The purpose of this study was to determine the trend of drug use among adolescents of the United States and Mississippi, and to estimate the differences of drug use prevalence as a whole, and by gender and by race. National and Mississippi YRBSS data from 2001 to 2021 were obtained for analysis. Summary statistics, prevalence ratio, and survey Chi-squared tests of independence statistics were generated for the comparison for all students, and by gender and race separately. Trend analysis was conducted using logistic regression combined with joinpoint regression. Six survey questions being studied were: have you ever used marijuana, inhalant, heroin, methamphetamines, injected drugs, and were you offered, sold, or given an illegal drug on school property during the last 12 months. Survey packages in R were used to account for the complex sampling design of YRBSS data. On the national level, all six drug related risk behaviors being studied showed significant decrease from 2001 to 2021. In Mississippi however, only “ever used marijuana” showed a trend of decrease, while three remain unchanged, and two increased. 2021 YRBSS data shows that Mississippi adolescents exhibited significantly higher prevalence of drug use, and are more likely to be offered, sold or given an illegal drug on school property. Our study suggests an urgent need for drug use intervention among Mississippi adolescents. More concerted actions at the community, school and government level are needed for reducing youth drug use and controlling the drug traffic on school property.

To realize the energy recovery of wheat straw, the pyrolysis behavior of wheat straw was studied at three heating rates (10, 20, and 30 K/min) based on thermogravimetric analysis (TG–DTG). Kinetics and thermodynamics were analyzed using Flynn–Wall–Ozawa (FWO) and Kissinger–Akahira–Sunose (KAS) model-free methods, and reaction mechanism was determined using Coats–Redfern (CR) model-fitting method. The results show that there are three weightlessness stages in the pyrolysis process, of which the second stage was the main weightlessness stage and two distinct peaks of weightlessness were observed in this stage. With increasing heating rate, the main pyrolytic weightlessness peaks of DTG curve shifts to higher temperature. The pyrolysis activation energy calculated by FWO and KAS methods are 165.17–440.02 kJ/mol and 163.72–452.07 kJ/mol, and the pre-exponential factor vary in the range of 2.58×1012–7.45×1036 s-1 and 1.91×1012–8.66×1037 s-1, respectively. The thermodynamic parameters indicates that wheat straw has the favorable conditions for product formation and containes potential energy to be utilized for bioenergy production, its pyrolysis reaction was non-spontaneous and the energy output is stable. CR method analysis shows that the A1/3 random nucleation model is the most suitable mechanism to characterize the pyrolysis process, and random nucleation may be in charge of the main pyrolysis stage. This study can provide a theoretical basis for the thermochemical conversion and utilization of wheat straw.

In this paper, we analyze the measurements of the normalized radar cross-section(NRCS) in Wave Mode for Chinese C-band Gaofen-3(GF-3) synthetic aperture radar (SAR). Based on 2779 images from GF-3 quad-polarization SAR in Wave Mode and collocated wind vectors from ERA-Interim, we verify the feasibility of using ocean surface wind fields and VV-polarized NRCS to perform normalized calibration. The method uses well-validated empirical C-band geophysical model function (CMOD4) to estimate the calibration constant for each beam. The Amazon rainforest experiment results show that the accuracy of obtained calibration constant meets the requirements. In addition, the relationship between cross-pol NRCS and wind vectors is discussed. The cross-pol NRCS increases linearly with wind speed and it has an approximate cosine modulation with the wind direction when the wind speed is greater than 8m/s. The cross-polarized system noise floor is low enough to ignore it in wind retrieval. Furthermore, we also investigate the properties of the polarization ratio, denoted PR, and show that it is dependent on incidence angle and azimuth angle. Two empirical models of the PR are fitted, one as a function of incidence angle only, the other with additional dependence on azimuth angle. Assessments show that the σ_VV^0 retrieved from new PR models as well as σ_HH^0 is in good agreement with σ_VV^0 extracted from SAR images directly. And it is also shown that considering the azimuth angle can improve polarization conversion accuracy.

Karakoram highway (K.K.H.) the only road link between two countries China and Pakistan. This road network is essential for two countries due to its strategic location and socioeconomic. The highway is more vulnerable due to landslide disasters, especially in rain and snow melting seasons, and different kinds of mass movement activities have occurred along K.K.H., such as rockfall, debris flow, and snow avalanche. The slope stability problems are widespread along with Karakorum (K.K.H.) between Besham city and the Dasu area because of the high seismic zone, rainfall, snow melting, and complex geology slope geometry, week, and adverse discontinuities sets. The detailed fieldwork was done along the Karakorum highway to minimize the risk of slope stability and for planning purposes in Besham to Dasu area and selected nine road-cut slopes. However, in these nine selected roadcut slopes, three slopes were already failed, four slopes are partially stable, and two slopes were stable. Both kinematic and empirical approaches are applied on all these nine road cut slopes and their discontinuities. The kinematic result has shown that all kinds of mode failure such as Toppling, Planar, and Wedge failure mode occurred in these slopes. The RMRb result has shown that all discounters lie in between fair to good rock. Both discrete and continuous (S.M.R.) results show that all discontinuity sets lie between the unstable, partially stable, and stable conditions.

Increased attention has been paid to the influence of coal mining subsidence on ecological environment. Restoration of ecosystem in damaged mining area is critical for restoring disturbed environment. The comparing of plant communities and microbial communities in the artificial restoration and natural restoration areas provides an effective method for evaluating the restoration effects. However, such studies are limited in coal mining subsidence restoration areas. Subsidence area in Shendong mining area, located in the semi-arid region of Western China, was restored from 2003 with 5 ecological restoration plant species. In July 2017, the comparison and analysis of plant and microbial communities were conducted at the artificial restoration areas (AR) and the natural remediation areas (NR). The results showed that the artificial ecological restoration in Shendong mining area has achieved some success, but it has not recovered to a similar ecosystem before the destruction. A higher plant species, coverage and bacterial community diversity were observed in AR. However, these features have lower similarity compared with those in NR sites. Potential soil factors, such as pH, moisture content, total carbon content, organic matter, nitrogen and bulk density, have a greater impact on soil bacterial community structure and diversity. In the ecological restoration of the mining area, attention should be paid to the restoration of soil properties in the mining area. This study can provide theoretical guidance for more scientific ecological restoration in the damaged mining area.

Impervious surface mapping with high-resolution remote sensing imagery has attracted increasing interest as it can provide detailed information for urban structure and distribution. Previous studies have suggested that the combination of LiDAR data and high-resolution imagery for impervious surface mapping performs better than using only high-resolution imagery. However, due to the high cost of the acquisition of LiDAR data, it is difficult to obtain the multi-sensor remote sensing data acquired at the same acquisition time for impervious surface mapping. Consequently, real landscape changes between multi-sensor remote sensing data at different acquisition times would lead to the error of misclassification in impervious surface mapping. This issue has mostly been neglected in previous works. Furthermore, the observation differences generated from multi-sensor data, including the problems of misregistration, missing data in LiDAR data, and shadow in high-resolution images would also challenge the final mapping result in the fusion of LiDAR data and high-resolution images. In order to conquer these problems, we propose an improved impervious surface mapping method incorporating both LiDAR data and high-resolution imagery at different acquisition times in consideration of real landscape changes and observation differences. In the proposed method, a multi-sensor change detection by supervised multivariate alteration detection is employed to obtain changed areas and misregistration areas. The no-data areas in the LiDAR data and the shadow areas in the high-resolution imagery are extracted by independent classification yielded by its corresponding single sensor data. Finally, an object-based post-classification fusion is proposed to take advantage of independent classification results with single-sensor data and the joint classification result with stacked multi-sensor data. Experiments covering the study site in Buffalo, NY, USA demonstrate that our method can accurately detect landscape changes and obviously improve the performance of impervious surface mapping.

China faces a persistent deficiency in feed protein resources. Enhancing the utilization efficiency of indigenous feed protein resources emerges as a viable strategy to alleviate the current deficit in protein feed supply. Corn gluten meal (CGM), characterized by high proportion of crude protein and glutamine, is predominantly employed in animal feed. Nonetheless, the water-insolubility of CGM protein hampers its protein bioavailability when utilized as feed material. This study aimed to augment protein bioavailability, liberate glutamine peptides from CGM, and produce gluta-mine-enriched CGM fermented feed. We executed a co-fermentation protocol using Bacillus subtilis A5, Lactobacillus 02002, and acid protease to generate the CGM fermented feed. Subsequent in vivo experiment with broilers were conducted to assess the efficacy of the fermented product. Findings revealed that the soluble protein, glutamine, small peptides, and lactic acid contents in the fer-mented feed increased by 69.1%, 700%, 47.6%, and 125.9%, respectively. Incorporating CGM fermented feed into the diet markedly enhanced the growth performance and intestinal health of broilers, positively modulated the cecal microbiota structure, and augmented the population of beneficial bacteria, specifically Lactobacillus. These results furnish both experimental and theoretical foundations for deploying CGM fermented feed as an alternative protein feed resource.

There is an increasing trend that Unmanned Combat Air Vehicles (UCAVs) are employed to complete different combat missions in modern wars. This paper investigates a UCAV routing problem, which simultaneously considers the decisions for the configuration of weapons carried by the UCAV subject to its capacity and the allocation of weapons to the targets subject to their destroying requirements. An integer linear programming model is developed to formulate the problem. An adaptive large neighborhood search (ALNS) heuristic is proposed to solve the problem, in which seven neighborhood structures are designed and employed. Randomly generated instances covering the small, medium and large sizes are used to test the proposed ALNS algorithm. CPLEX is also utilized to solve the small-size instances, whose results are compared with that obtained by the ALNS algorithm. And the extensive experimental results confirm the effectiveness and superiority of the proposed ALNS algorithm.

Protein phosphorylation and ADP-ribosylation (ADPr), as two types of post-translational modifications (PTM), are the process of adding phosphate group and ADP-ribose moieties to proteins, respectively. Although both PTM types can occur on many amino acid types, serine is the most common. Serine phosphorylation (pS), serine ADPr (SADPr), and their in situ crosstalks (pSADPr) play essential roles in biological processes. Although in silico classifiers have been developed for predicting pS and SADPr sites, the classifier for predicting pSADPr sites is unavailable. In this study, we developed classifiers to predict pSADPr sites. Specifically, we collected 3250 human pSADPr, 7520 SADPr, 151,227 pS and 80,096 unmodified serine sites. Based on them, we investigated the characteristics of pSADPr sites and constructed three classifiers to predict pSADPr sites from the pS dataset, the SADPr dataset and the protein sequences separately. We built and evaluated five deep-learning classifiers in ten-fold cross-validation and independent test datasets. Three of them (e.g. Convolutional Neural Network with the One-Hot encoding, dubbed CNNOH) performed better than the rest two. For instance, CNNOH had the AUC values of 0.700, 0.914 and 0.954 for recognizing pSADPr sites from the SADPr, pS and unmodified serine sites.Therefore, it is challenging to distinguish pSADPr sites from SADPr sites compared to the other two. It is consistent with our observation that pSADPr's characteristics are more similar to those of SADPr than the rest. Furthermore, we used the classifiers as base classifiers to develop a few stacking-based ensemble classifiers to improve performance. However, none of the ensemble classifiers showed better performances, suggesting that the base classifiers have good enough performances. Finally, we developed an online tool for extensively predicting human pSADPr sites based on the CNNOH classifier, dubbed EdeepSADPr. It is freely available through http://edeepsadpr.bioinfogo.org/.

This study explored what motivates university counselors. By analyzing various factors like personal values and work environment, they found counselors experience greater career satisfaction when their work aligns with their own values and societal impact, and when they receive recognition and opportunities for growth. Universities can utilize these findings to create a more supportive environment for counselors by highlighting their impact, offering development opportunities, and fostering a positive work culture. This can ultimately lead to a more motivated and effective counseling team, benefiting both the counselors and the students they serve.

Environmentally friendly lead-free K1-xNaxNbO3 (KNN) ceramics possess electromechanical properties comparable to lead-based ferroelectric materials, but cannot meet the needs of device miniaturization, and the corresponding thin films lack of theoretical and experimental studies. To this end, we developed the nonlinear phenomenological theory for ferroelectric materials to study the effects of non-equiaxed misfit strain on the phase structure, electromechanical properties and electrical response of K0.5Na0.5NbO3 epitaxial films and constructed the in-plane misfit strain (u1-u2) phase diagrams. The results show that K0.5Na0.5NbO3 epitaxial film under non-equiaxed in-plane strain can exhibit abundant phase structures, including orthorhombic a1c, a2c and a1a2 phases, tetragonal a1, a2 and c phases, and monoclinic r12 phases. Moreover, in the vicinity of a2c-r12, a1c-c and a1a2-a2 phase boundaries, K0.5Na0.5NbO3 epitaxial films exhibit excellent dielectric constant ε11, while at a2c -r12 and a1c-c phase boundaries large piezoelectric coefficient d15 is observed. It was also found that high permittivity ε33 and piezoelectric coefficients d33 exist near the a2c - a2, r12- a1a2 and a1c-a1 phase boundaries due to the existence of polymorphic phase boundaries (PPB) in the KNN system, which makes it easy to polarize near the phase boundaries, and the polarizability changes suddenly, leading to electromechanical enhancement. In addition, the results show that the K0.5Na0.5NbO3 thin films possess a large electrocaloric response at the phase boundary at the r12-a1a2 and a1c-a1 phase boundaries. And the maximum adiabatic temperature change ∆T is about 3.62 K when the electric field change is 30 MV/m at room temperature, which is significantly enhanced compared with equiaxed strain. This study provides theoretical guidance for obtaining K1-xNaxNbO3 epitaxial thin films with excellent properties.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

The traditional Simultaneous Localization and Mapping (SLAM) systems are based on the 1 strong static assumption, and their performance will degrade significantly due to the presence of 2 dynamic objects located in dynamic environments. To decrease the effects brought by the dynamic 3 objects, based on ORB-SLAM2 system framework, a novel dynamic semantic SLAM system called 4 MOR-SLAM is presented using mask repair method, which can accurately detect dynamic objects 5 and realize high-precision positioning and tracking of the system in dynamic indoor environments. 6 First, an instance segmentation module is added to the front end of ORB-SLAM2 to distinguish 7 dynamic and static objects in the environment and obtains a preliminary mask. Next, to overcome the 8 under-segmentation problem in instance segmentation, a new mask inpainting model is proposed to 9 ensure that the integrity of object masks, which repairs large objects and small objects in the image 10 with depth value fusion method and morphological method respectively. Then, a reliable basic matrix 11 can be obtained based on the above repaired mask. Finally, the potential dynamic feature points 12 in the environment are detected and removed through the reliable basic matrix, and the remaining 13 static feature points are input into the tracking module of the system to realize the high-precision 14 positioning and tracking in dynamic environments. The experiments on the public TUM dataset 15 show that, compared with ORB-SLAM2, the MOR-SLAM improves the absolute trajectory accuracy 16 by 95.55%. In addition, compared with DynaSLAM and DS-SLAM on the high-dynamic sequences 17 (fr3/w/rpy and fr3/w/static), the MOR-SLAM improves the absolute trajectory accuracy by 15.20% 18 and 59.71%, respectively

Underwater acoustic sensor network (UASN) plays a crucial role in collecting real-time data from remote areas of the ocean. However, deploying the UASN is a challenging problem due to the harsh environment and high deployment cost. Therefore, it is essential to design an appropriate routing protocol to effectively address the issues of routing void, packet delivery delay, and energy utilization. In this paper, an adaptive support-vector-machine-based routing (ASVMR) protocol is proposed for the UASN to prolong the network lifetime and reduce the end-to-end packet delivery delay. The proposed protocol employs a distributed routing approach that dynamically optimizes the routing path in real-time by considering four types of node state information. Moreover, the ASVMR protocol establishes a "routing vector" spanning from the current node to the sink node, and selects a suitable pipe radius according to the packet delivery ratio (PDR). In addition, the ASVMR protocol incorporates future states of sensor nodes into the decision-making process, along with the adoption of a waiting time mechanism and routing void recovery mechanism. Extensive simulation results demonstrate that the proposed ASVMR protocol performs well, in terms of the PDR, the hop count, the end-to-end delay, and the energy efficiency in dynamic underwater environments.

Ditching-rotary tiller was widely used in tillage and ditching furrow during rapeseed sowing. As its ditching furrow system (consist of four identical ditching plows) would bear great drag resistance from the soil during operation, the ditching plow was optimized based on differential geometry analysis and EDEM simulation. Resistance-velocity simulation indicated the plow with parabolic type guide curve had better reduce-drag characteristics. Differential geometry analysis indicated decay rate of E and growth rate of G could represent the variable regularity of drag resistance with the increase of velocity. The L value could represent the magnitude of drag resistance. The smaller L value, decay rate of E and growth rate of G, the better drag-reduce characteristics. Quadratic rotation orthogonal combination design shown the optimal structural parameter values were: Δθ=15°, θmin=45°, h=250mm, l=100mm. The minimum average drag resistance was 230.1N. The differential geometry analysis of optimal ditching plow shown |dE/dκ| and |dG/dκ| could obtain minimum value, indicating growth rate of drag resistance for optimal plow was the lowest within the experimental level. Field experiment indicated the operation effect of optimized ditching furrow system could met the requirements of rapeseed sowing. The research provided in-depth theoretical guidance for Drag-reduce design of plow.

The biodiversity loss in urban areas has attracted public concern, which is one of the urgent global environmental issues. This study used bibliometric methods to analyze 3351 publications from 1995-2021 that retrieved from the Web of Science and visually represented the state-of-the-art of researches in city biodiversity field. The prolific authors, journals(sources), institutions, and countries are clearly identified. The most cited and influential paper proposed a conceptual framework of associations between urban green space, and ecosystem and human health, and then concluded that green infrastructure could physically and psychologically benefits people by ecosystem services it provides, and make a better socio-economic benefit. The theme hotspots are urbanization, urban ecology, ecosystem services, urban planning, green infrastructure, urban forest and urban park et al. Ingo Kowarik is the most productive author in terms of number of publications. Michael L. McKinney is the most cited authors by the publications in analyzed corpus, who identified how urbanization harms native ecosystems, however, a well ecologically educated population could greatly enhance species richness in all ecosystems. Urban park, garden, fragmented green spaces and green corridor networks could help enhance city biodiversity. In general, the city biodiversity research presents a trend that involves intensive global cooperation, and become more comprehensive.

We propose a chemical language processing model to predict polymers’ glass transition temperature (Tg) through a polymer language (SMILES, Simplified Molecular Input Line Entry System) embedding and recurrent neural network. This model only receives the SMILES strings of polymer’s repeat units as inputs and considers the SMILES strings as sequential data at the character level. Using this method, there is no need to calculate any additional molecular descriptors or fingerprints of polymers, and thereby, being very computationally efficient and simple. More importantly, it avoids the difficulties to generate molecular descriptors for repeat units containing polymerization point `*’. Results show that the trained model demonstrates reasonable prediction accuracy on unseen polymer’s Tg. Besides, this model is further applied for high-throughput screening on an unlabeled polymer database to identify high-temperature polymers that are desired for applications in extreme environments. Our work demonstrates that the SMILES strings of polymer’s repeat units can be used as an effective feature representation to develop a chemical language processing model for predictions of Tg. The framework of this model is general and can be used to construct structure-property relationships for other polymer’s properties.

Standard Ethernet (IEEE 802.3 and the TCP/IP protocol suite) is gradually applied in industrial control system (ICS) with the development of information technology. It breaks the natural isolation of ICS, but contains no security mechanism. A modified intrusion detection system (IDS), which is strongly correlated to specific industrial scenario, is necessary for modern ICS. On the one hand, this paper outlines attack models, including infiltration attacks and our creative forging attack. On the other hand, we proposes a hierarchical IDS, which contains a traffic prediction model and an anomaly detection model. The traffic prediction model, which is based on autoregressive integrated moving average (ARIMA), can forecast the traffic of ICS network in the short term and precisely detect the infiltration attacks according to abnormal changes in traffic pattern. The anomaly detection model using one-class support vector machine (OCSVM) is able to detect malicious control instructions by analyzing the key field in EtherNet/IP packets. The experimental results show that the hierarchical IDS has an outstanding performance in detecting infiltration attacks and forging attack compared with other two innovative IDSs.

Cut chrysanthemum, renowned as a highly favored floral choice globally, experiences a significant decline in production due to the practice of continuous cropping. The adverse physiological effects on cut chrysanthemums have been observed as a result of the degradation of soil physical and chemical properties, coupled with the proliferation of pathogens. It is noteworthy that the 'Guangyu' cultivar in Xinxiang, Henan province, China, has been specifically impacted by these effects. This study effectively identified and validated the precise pathogen accountable for wilt disease initially. Subsequently, an analysis was conducted to examine the invasion pattern of the pathogen and the physiological response of the chrysanthemum. Finally, PacBio platform was employed to investigate the dynamic alterations in the microbial community within the soil rhizosphere, comparing the effects of seven years of monocropping with the first year. The findings indicated that Fusarium solani was the primary causative agent responsible for wilt disease, as it possessed the ability to invade and establish colonies in plant roots, leading to alterations in various physiological parameters of the plants. Furthermore, the practice of continuous cropping had been observed to significantly disturb the microbial community composition, potentially acting as an additional influential factor in the advancement of wilt.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

With the rising cost of animal feed protein, finding affordable and effective substitutes is crucial. Walnut kernel cake, a polyphenols, fiber, protein and fat-rich byproduct of walnut oil extraction, has been underexplored as a potential protein replacement in pig feed. In this study, we found that feeding large Diqing Tibetan pigs walnut kernel cake promoted adipose deposition and improved pork quality during pig growth. Transcriptome analysis revealed the upregulation of genes ANGPTL8, CCNP, ETV4, and TRIB3, associated with adipose deposition. Pathway analysis highlighted enrichment in adipose-deposition-related pathways, including PPAR, Insulin, PI3K-Akt, Wnt, and MAPK signaling. Further analysis identified DEGs (differentially expressed genes) positively correlated with adipose-related traits, such as PER2 and PTGES. Single-cell transcriptome data pointed to the specific expression of CD248 and PTGES in adipocyte progenitor/stem cells (APSCs), pivotal for adipocyte differentiation and adipose deposition regulation. This study demonstrates walnut kernel cake's potential to substitute soybean cake in pig feed, providing high-quality protein and promoting adipose deposition. It offers insights into feed protein replacement, human functional food, fat metabolism, and related diseases, with marker genes and pathways supporting pig breeding and pork quality improvement.

This research investigates the implementation of complex exponential-based neurons in FPGA, which can pave the way for implementing bio-inspired spiking neural networks to compensate for the existing computational constraints in conventional artificial neural networks. The increasing use of extensive neural networks and the complexity of models in handling big data lead to higher power consumption and delays. Hence, finding solutions to reduce computational complexity is crucial for addressing power consumption challenges. The complex exponential form effectively encodes oscillating features like frequency, amplitude, and phase shift, streamlining the demanding calculations typical of conventional artificial neurons through levering simple phase addition of complex exponential functions. The article implements such a two-neuron and a multi-neuron neural model using Xilinx system generator and Vivado design suite, employing 8-bit, 16-bit, and 32-bit fixed-point data format representations. The study evaluates the accuracy of the proposed neuron model across different FPGA implementations while also providing a detailed analysis of operating frequency, power consumption, and resource usage for the hardware implementations. BRAM-based Vivado designs outperformed Simulink regarding speed, power, and resource efficiency. Specifically, the Vivado BRAM-based approach supported up to 128 neurons, showcasing optimal LUT and FF resource utilization. Such outcomes accommodate choosing the optimal design procedure for implementing spiking neural networks on FPGAs.

Vibration signal analysis is regarded as a fundamental approach in diagnosing faults in rolling bearings, and recent advancements have shown notable progress in this domain. However, the presence of substantial background noise often results in the masking of these fault signals, posing a significant challenge for researchers. In response, an Adaptive Denoising Autoencoder (ADAE) approach is proposed in this paper. The data representations are learned by the encoder through convolutional layers, while the data reconstruction is performed by the decoder using deconvolutional layers. Both the encoder and decoder incorporate adaptive shrinkage units to simulate denoising functions, effectively removing interfering information while preserving sensitive fault features. Additionally, dropout regularization is applied to sparsify the network and prevent overfitting, thereby enhancing the overall expressive power of the model. To further enhance ADAE's noise resistance, shortcut connections are added. Evaluation using publicly available datasets under scenarios with known and unknown noise demonstrates that ADAE effectively enhances the signal-to-noise ratio in strongly noisy backgrounds, facilitating accurate diagnosis of faults in rolling bearings.

The prediction of stock prices holds significant implications for researchers and investors in evaluating stock value and risk. In recent years, researchers have increasingly replaced traditional machine learning methods with deep learning approaches in this domain. However, the application of deep learning in forecasting stock prices is confronted with the challenge of overfitting. To address the issue of overfitting and enhance predictive accuracy, this study proposes a stock prediction model based on GRU (Gated Recurrent Unit) with reconstructed datasets. This model integrates data from other stocks within the same industry, thereby enriching the extracted features and mitigating the risk of overfitting. Additionally, an auxiliary module is employed to augment the volume of data through dataset reconstruction, thereby enhancing the model’s training comprehensiveness and generalization capabilities. Experimental results demonstrate a substantial improvement in prediction accuracy across various industries.

The Asian longhorned beetle (ALB), Anoplophora glabripennis is a forestry pest found worldwide. ALB causes serious harm because of the lack of natural enemies in the invaded areas. Dastarcus helophoroides and Dendrocopos major are important natural enemies of ALB. MaxEnt was used to simulate the distribution of D. helophoroides and D. major in China and Xinjiang, and their suitable areas were superimposed to evaluate the pest control ability of D. helophoroides and D. major. The results showed that, with climate change, the suitable areas of D. helophoroides and D. major migrated northward; the centroid shift of ALB was greater than that of D. helophoroides and D. major, which would lead to fewer natural enemies encountered by ALB during migration, reduce the control ability of natural enemies, and increase the risk of disastrous outbreaks in the invaded areas. We found that the damage caused by ALB was not serious in the areas with natural enemies and very serious in the areas without natural enemies. We suggest that natural enemies should be included in the model used for predicting suitable areas for invasive pests, as this is more conducive to assessing the risks of invasive organisms to the local ecological environment.

The ecological background condition of the semi-arid steppe region (SASR) is extremely fragile. It is recognized that the development of coal and electricity power is a kind of strong human interference behavior for regional landscape ecology. Landscape ecological classification (LEC) is the premise of landscape ecology research of the mining area. The current research on the SASR and grassland LEC of coal-power base is relatively less, but still remains uncertainty concerning how to stratify and classify urban mining landscapes into units of ecological significance at spatial scales appropriate for management. This study is based on hierarchy theory, scale theory, landscape process, the patch-corridor-matrix model, the network, the theory of multiple planning integration and the principle of remote sensing. According to the comprehensive principle, principles of the combining of structure and function, principle of the combining human-ominated and natural landscape, principle of emphasis, and principle of combining qualitative analysis with quantitative research of LEC in large-scale coal-power base(LSCPB). On the basis of occurrence method land classification, fully consider the ecological attributes of the land, integration pattern, processes and function theory of the landscape ecology, the LEC system of the LSCPB in the SASR has been constructed by using top-down decomposition classification method. Empirical research of the Victory and Mindong No.1 mining areas of Shenhua Group shows that the classification system constructed in this paper can meet the requirements of LEC and fully reflect the status of landscape ecology of LSCPB in SASR. This study can provide theoretical guidance for the landscape ecology of LSCPB, while also supporting a theoretical reference for the LEC research.

A real-time two-way direct load control (TWDLC) of central air-conditioning chillers in wide area is proposed to provide demand response. The proposed TWDLC scheme is designed to optimize the load shedding ratio of every customer under control to ensure the target load to be shed is met at every scheduling period. In order to overcome the load reduction uncertainties of TWDLC, an innovative solution is proposed by applying a certain degree of loosening on the constraint of the actual shed load. Fuzzy linear programming is utilized to solve the optimization problem with fuzzy constraints. The proposed fuzzy linear programming problem is solved by delicately transforming it into a regular liner programming problem. A selection scheme used to obtain the feasible candidates set for load shedding at every sampling interval of TWDLC is also designed along with the fuzzy linear programming.

Histone post-translational modification is one of the main mechanisms of epigenetic regulation, which plays a crucial role in the control of gene expression and various biological processes. However, whether or not it affects fungal virulence is not clear in Sclerotinia sclerotiorum. In this study, we identified and cloned the histone methyltransferase Defective in methylation 5 (Dim5) in S. sclerotiorum, which encodes a protein containing a typical SET domain. SsDim5 was found to be dynamically expressed during infection. Knockout experiment demonstrated that deletion of SsDim5 reduced the virulence in Ssdim5-1/Ssdim5-2 mutant strains, accompanied by a significant decrease in H3K9 trimethylation levels. Transcriptomic analysis further revealed the downregulation of genes associated with mycotoxins biosynthesis in SsDim5 deletion mutants. Additionally, the absence of SsDim5 affected the fungus's response to oxidative and osmotic, as well as cellular integrity. Together, our results indicate that the H3K9 methyltransferase SsDim5 is essential for H3K9 trimethylation, which regulating fungal virulence to host plants through impacting on mycotoxins biosynthesis, and the response to environmental stresses in S. sclerotiorum.

Background: Progression of metabolic dysfunction associated steatotic liver disease (MASLD) to steatohepatitis (MASH) is driven by stress-inducing lipids that promote liver inflammation and fibrosis. MASH can lead to cirrhosis and hepatocellular carcinoma. We showed coordinated defenses regulated by transcription factors, nuclear factor erythroid 2 related factor-1 (Nrf1) and -2 (Nrf2), protect against hepatic lipid stress. Here, we investigated protective effects of hepatocyte Nrf1 and Nrf2 against MASLD-induced liver fibrosis and tumorigenesis. Methods: Using mice fed MASH diet for 24-52 weeks, we examined MASLD in mice with hepatocyte specific Nrf1, Nrf2, or combined deletion, and compared this to control. In a separate study, mice received weekly injections of carbon tetrachloride to induce liver fibrosis. From week 16-24, mice were treated with Nrf2 activating drug bardoxolone, hepatocyte overexpression of human NRF1 (hNRF1), or both, and groups were compared to control. Results: Hepatocyte Nrf2 deficiency had no effect. Hepatocyte Nrf1 and combined deficiency caused MASH but only hepatocyte Nrf1 deficiency in male mice increased tumor number. Bardoxolone reduced liver steatosis, fibrosis, inflammation, and proliferation, and this effect when combined with hNRF1 was greater than bardoxolone alone. Conclusion: Physiologic Nrf1 delays MASLD progression, Nrf2-induction alleviates MASH, and combined enhancement synergistically protects against steatosis.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

A common task in the immunodetection of structurally close compounds is to analyze the selectivity of immune recognition: it is required to understand the regularities of immune recognition and to elucidate the basic structural elements which provide it. Triazines are compounds of particular interest for such a research due to their high variability and the necessity of their monitoring to provide safety of agricultural products and foodstuffs. We evaluated the binding of 20 triazines with polyclonal (pAb) and monoclonal (mAb) antibodies obtained using atrazine as the immunogenic hapten. A total of >3000 descriptors was used in QSAR analysis of binding activities (pIC50). Comparison of the two enzyme immunoassay systems showed that the system with pAb is much easier to describe using 2D QSAR methodology, while the system with mAb can be described using the 3D QSAR COMFA. Thus, for the 3D QSAR model of the polyclonal antibodies, the main statistical parameter q² (‘leave-many-out’) is equal 0.498, and for monoclonal antibodies q² is equal 0.566. Obviously, in the case of pAb, we deal with several targets, while in the case of mAb the target is one, and therefore it is easier to describe it using specific fields of molecular interactions distributed in space.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

The intestinal microbial community of aquatic animals is closely related to the environment and thus affects the health of aquatic animals. Here we investigated annual variation of intestinal bacteria community structures of Ruditapes philippinarum cultured using two different methods, bottom sown and raft hanging. Bacterial diversity of seawater and sediment in different seasons was examined as well. Correlation between R. philippinarum intestinal bacteria community structures and environmental factors was analyzed. The results showed that in the two aquculture areas where R. philippinarum was differentially cultured, bacteria community structure of seawater and sediment both altered with seasons. However, neither seasonal changes nor difference in culture methods could significantly affect the intestinal bacteria community structures of R. philippinarum. Additionally, in terms of the alpha diversity of intestinal bacteria communities, there was no significant difference in R. philippinarum cultured using the two methods. For benthic cultured clams, alpha diversity of the intestinal bacterial communities was often higher than that of the environmental bacterial communities. For raft hanging cultured calms, Alpha diversity of the intestinal bacterial communities was normally comparable with that of the environmental counterparts. Beta diversity analysis showed that the intestinal bacterial community structure of R. philippinarum was mainly determined by both deterministic and stochastic processes. Correlation analysis showed that the intestinal bacterial community structures of R. philippinarum were determined by a variety of environmental factors. For clams collected from the benthic culture area, the intestinal bacterial structure was more correlated with the physicochemical properties of sediment in comparing with those of seawater. For clams collected from the raft-culture area, the intestinal bacterial structure was mainly determined by the phsicochemical characteristics of seawater. This study helps us to better understand the bacterial community structure in complex aquaculture ecosystems, providing a reference for healthy shellfish aquaculture and ecosystem protection in aquaculture area.

To realize the utilization of peanut shell, this study investigates the combustion behavior, chemical kinetics, and thermodynamic parameters of peanut shell using TGA under atmospheric air. Results indicate that increasing the heating rate leads to higher ignition, burnout, and peak temperatures, as observed in the TG/DTG curves shifting to the right. Analysis of combustion performance parameters suggest that higher heating rates can enhance combustion performances. Kinetic analysis using two model-free methods, KAS and FWO, shows that the activation energy (Eα) ranges from 93.30 to 109.65 kJ/mol for FWO and 89.72 to 103.88 kJ/mol for KAS. The data fit well with coefficient of determination values (R2) close to 1. Pre-exponential factors using FWO range from 2.19×106 to 8.06×107 s–1, and for KAS range from9.72×105 to 2.25×107 s–1. Thermodynamic analysis indicates a low-energy barrier (≤ ±6 kJ/mol) between activation energy and enthalpy changes, suggesting easy reaction initiation. Furthermore, variations in enthalpy (ΔH), Gibbs free energy (ΔG), and entropy (ΔS) upon conversion (α) suggest that peanut shell combustion is endothermic and non-spontaneous, with the generation of more homogeneous or well-ordered products as combustion progresses. These findings offer a theoretical basis and data support for the further utilization of agricultural biomass.

This proposed research explores a novel approach to image classification by deploying a complex-valued neural network (CVNN) on a field-programmable gate array (FPGA), specifically for classifying 2D images transformed into polar form. The aim of this research is to address the limitations of existing neural network models in terms of energy and resource efficiency, by exploring the potential of FPGA-based hardware acceleration in conjunction with advanced neural network architectures like CVNNs. The methodological innovation of this research lies in the Cartesian to polar transformation of 2D images, effectively reducing the input data volume required for neural network processing. Subsequent efforts focused on constructing a CVNN model optimized for FPGA implementation, emphasizing the enhancement of computational efficiency and overall performance. The experimental findings provide empirical evidence supporting the efficacy of the image classification system developed in this study. One of the developed models, CVNN_128, achieves an accuracy of 88.3% with an inference time of just 1.6ms and a power consumption of 4.66mW for the classification of the MNIST test dataset consists of 10,000 frames. While there is a slight concession in accuracy compared to recent FPGA implementations that achieve 94.43%, our model significantly excels in classification speed and power efficiency—surpassing existing models by more than a factor of 100. In conclusion, the paper demonstrates the substantial advantages of FPGA-implementation of CVNNs for image classification tasks, particularly in scenarios where speed, resource, and power consumption are critical. The study’s reproducible results and corresponding code are available on GitHub at the following link: https://github.com/mahmad2005/CVNNonFPGA

Positive invariant set is an important concept of dynamic systems. The purpose of this paper is to study the sufficient and necessary conditions that the set of ellipsoids and the Lorenz cone are positive invariant sets of discrete time systems. By means of nonlinear programming and induced norm, the problem of positive invariance is formulated as an optimization problem, and the equivalent dual form optimization is also presented using the dual optimization method. Our results provide more alternative methods for determining the positive invariance of quadratic form convex sets from the point of view of optimization and dual optimization. The effectiveness of this method is demonstrated by numerical examples.

The adsorption of supramolecular composites for Cs(I) in high level liquid waste (HLLW) are different due to different carriers. We chose 25,27-bis(ethyl)-calix[4]arene-26,28-crown-6 (EC[4]C6) as adsorbent, SiO2-P, XAD-7 and UiO-66 as carriers. The synthesis and characterization of supramolecular EC[4]C6 loaded with three different carriers were presented. SEM, N2 adsorption/desorption isotherms, TG-DSC spectra, FT-IR spectra results shown that EC[4]C6 was successfully introduced into the pores of carriers via physical intermolecular interactions. EC[4]C6/SiO2-P, EC[4]C6/XAD-7 and EC[4]C6/UiO-66 shown high efficiency, high selectivity towards Cs(I) over 18 typical fission or corrosion products in HNO3 solution. The adsorption properties of the three materials were investigated after electron irradiation. These results demonstrate that EC[4]C6/SiO2-P possess greater potential for highly efficient removal of Cs(I) from HLLW.