Coronavirus disease (COVID-19) is an infectious disease caused by a new virus which causes respiratory illness. Older adults and people who have previous chronic medical conditions are at higher risk for more serious complications from COVID-19.Hypovitaminosis D is attributed to the increased risk of lung injury and acute respiratory distress syndrome (ARDS) as well as diabetes, Cardiovascular event and associated comorbidities, which are the main causes of severe clinical problem in COVID-19 patients. Considering the protective role of vitamin D through modulating the innate and adaptive immune system as well as inhibition of Renin Angiotensin System (RAS), vitamin D supplementation might boost the immune system of COVID-19 patients and reduce severity of the disease in vitamin D deficient individuals.

The Corona Virus Disease 2019 (COVID-19) outbreak is becoming pandemic with the highest mortality in people with associated comorbidities. These RNA viruses containing four structural proteins usually use spike protein to enter the host cell. It has been demonstrated that Angiotensin Converting Enzyme 2 (ACE2) ,as a part of renin-angiotensin-aldosterone system (RAAS), acts as a host receptor for the virus which is the main target of therapeutic approaches. However, medications acting on RAAS can lead to serious complications especially in people with diabetes and hypertension. To avoid this, other potential treatment modalities should be used in COVID-19 patients with associated comorbidities.

Results: A total of 6270 individuals were assessed (1615 severe and 4655 non-severe patients). The median age was 63 (95% CI: 49-74) and 47 (95% CI: 19-63) years in the severe and non-severe groups, respectively. Moreover, about 41% of patients had comorbidities. Severity was higher in patients with history of cerebrovascular disease: OR 4.85 (95% CI: 3.11-7.57). The odds of being in severe group increase by 4.81(95% CI: 3.43-6.74) for history of cardiovascular disease (CVD). This was 4.19 (95% CI: 2.84-6.19) for chronic lung disease and 3.18, 95% CI: 2.09-4.82 for cancer .The odds ratio of a diabetes and hypertension were 2.61 (95% CI: 2.02-3.3), and 2.37( 95% CI: 1.80-3.13) respectively.

Aim: Abnormal laboratory findings have been shown to be associated with severe COVID-19. However, all aspects of this association have not been reviewed systematically. Therefore, the aim of this meta-analysis was to explore crucial laboratory parameters in severe COVID-19 infection. Methods: We performed the literature review of scientific articles indexed in electronic databases. Scientific search engines were used to perform the electronic literature search. After the removal of duplicates and selection of articles of interest, 30 studies were eligible to include. If heterogeneity was high (I²>50%), a random-effects model was applied to combine the data. Otherwise, a fixed-effects model was used.Results: A total of 5586 individuals were assessed (1555 patients with severe COVID-19 infection and 3452 with non-severe infection). Platelets, lymphocytes and serum albumin were significantly lower in severe patients while other biochemical and immunological parameters including prothrombin time, ALT, AST, total bilirubin, LDH, procalcitonin, CRP, IL-6, and IgA were significantly higher in patients with severe infection. Neutrophil and monocyte counts as well as hemoglobin level, D-dimer, hypersensitive troponin I, IL-2R, IgG and IgM levels were different between two groups; however, the difference was not statistically significant (All P-values >0.05). Conclusions: Lymphopenia, elevated liver enzymes, and high levels of inflammatory biomarkers are associated with severe COVID-19 infection.

This paper reports on the optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation systems for cattle farming in rural areas of Bangladesh. Bangladesh is a lower middle-income country with declining rates of poverty among its 160 million people due to persistent economic growth in conjunction with balanced agricultural improvements. Most of the rural households adopt a mixed farming system by cultivating crops and simultaneously rearing livestock. Among the animals raised, cattle are considered as the most valuable asset for the small/medium-scale farmers in terms of their meat and milk production. Currently, along with the major health issue, the COVID-19 pandemic is hindering the world’s economic growth and has thrust millions into unemployment; Bangladesh is also in this loop. However, natural disasters such as COVID-19 pandemic and floods, largely constrain rural smallholder cattle farmers from climbing out of their poverty. In particular, small and medium-scale cattle farmers face many issues that obstruct them from taking advantage of market opportunities and imposing a greater burden on their families and incomes. An appropriate measure can give a way to make those cattle farmers’ businesses both profitable and sustainable. Optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation system for cattle farming is a new and forward-looking approach for sustainable development of the livestock sector. In this study, we design and optimize a thin-film coating assisted hybrid (photovoltaic-battery-generator) power system by using the Hybrid Optimization of Multiple Energy Resources (HOMER, Version 3.14.0) simulation tool. An analysis of the results has suggested that the off-grid hybrid system is more feasible for small and medium-scale cattle farming systems with long-term sustainability to overcome the significant challenges faced by smallholder cattle farmers in Bangladesh.

The adverse relationship between viral hepatitis and pregnancy in developing countries was seen as a reflection of retrospective biased hospital-based data collection by the West. However, the discovery of HEV from an epidemic of non-A, non-B hepatitis in Kashmir and documenting increased incidence and severity of hepatitis E in pregnancy from a house-to-house survey unmasked the unholy alliance. Among the family of HEV’s, genotype (gt)-1, with a unique ORF4-encoded protein enhancing viral polymerase activity and viral replication, is the sole HEV that shows this adverse relationship. The epidemics caused by HEV-gt1 and not by HEV-gt2 show adverse relationship with pregnancy. The pathogenesis of the unholy alliance is complex and at present not well understood. Possibly multiple factors play a role in causing severe liver disease in the mother including: infection, replication and damage to the maternal-foetal interface by HEV-gt1; vertical transmission of HEV to foetus causing severe foetal/neonatal hepatitis; and combined viral and hormone related immune dysfunction of diverse nature in the mother promoting viral replication. Management is multidisciplinary and needs a close watch for the development and management of ALF. Preliminary data suggest beneficial maternal outcomes by early termination of pregnancy in patients with lower grades of encephalopathy.

Bangladesh's railway system mostly uses typical manual railway crossing technique or boom gates through its 2,955.53 km rail route all over the country. The accidents are frequently happening in the railway crossings due to not having obstacle detectable and quickly operating gate systems, and also for fewer safety measures in the railway crossing. Currently, there are very few automatic railway crossing systems (without obstacle detectors) available, however, all of them are dependent on the national power grid without a backup plan for any emergency cases. Bangladesh is still running a bit behind in the power generation of its consumption, hence it is not possible to have a continuous power supply at all times all over the countryside. We aim to design and develop a smart railway crossing system with an obstacle detector to prevent common types of accidents in the railway crossing points. We design to use two infrared (IR) sensors to operate the railway crossing systems which will be controlled by the Arduino Uno. This newly designed level crossing system will be run with the help of sustainable renewable energy which is cost-effective, eco-friendly, and apply under the national green energy policy towards achieving sustainable development in Bangladesh as a part of the global sustainable goal to face climate change challenges. We have summarized the simulated results of several renewable energy sources including a hybrid system and optimized the Levelized Cost of Energy (LCOE), and the payback periods.

This research project focuses on the optimization of the hybrid energy system together with the assistance of thin-film coatings aiming to achieve self-sustainable food and crop storage facilities which will run effectively with its own generated energy. An infrastructure will be designed and constructed that will comprise a hybrid power generation system accompanied by thin-film coated semitransparent and non-transparent construction materials for energy saving. Thin-film low emissivity (Low-E) type coatings will assist the transparent or semitransparent construction materials to reflect most of the infrared (IR-mostly heat) and UV spectra of sunlight without interrupting the visible spectrum and will lead to saving energy consumption by reducing the heat and lighting during day time

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

In 2020, students of Pakistan had to adapt to the online environment for the very first time. This study aims to analyze the perceptions of medical, dental, and allied health students about online education in Pakistan. A descriptive, cross-sectional study was done to assess the level of acceptance of undergraduate students. A pre-validated questionnaire regarding demographics, past-experience of e-learning, advantages disadvantages of e-learning, and general perception of students towards e-learning was distributed. Descriptive statistics were computed for demographics, Mann-Witney-U test was used to compare the differences of perceptions between pre-clinical year and clinical years students. Kruskal-Wallis test was applied to compare the results of three specialties of students. Chi-square was used to compare overall category-wise positive and negative responses of students. 1200 students participated in the study. The major advantage identified by all students was the ‘comfortable environment’ in which they studied online. The major disadvantage selected by preclinical year students was ‘anxiety due to social isolation’ and that chosen by clinical year students was ‘lack of patient interaction’. Overall, 72% of students had a negative perception of e-learning. Student-teacher training, student counselling sessions, and innovative techniques need to be introduced to enhance student engagement and reduce pandemic stress.

Escherichia coli or E. coli is a member of the fecal coliform group and is a more specific indicator of fecal contamination than other fecal coliform species, its presence indicate possibly presence of harmful bacteria which will cause diseases and it also suggests the extent as well as the nature of the contaminants. E. coli bacteria able to survive in water for 4 – 12 weeks and at present, it appears as an indicator to provide the accurate bacterial contamination of fecal matter in drinking water, because of the availability of simple, affordable, fast, sensitive and exact detection techniques. According to the laboratory experiment based techniques, 24 - 48 hours are required for the bacterial concentration to be reported. So, there is a necessity for continuous monitoring. Techniques for detection of many pathogenic bacterial strains are not yet available, sometimes days to weeks are required to get the results. To overcome the difficulties, expensive and time-consuming techniques are required to detect, count and identify the presence of specific bacterial strain. Public health relies on online monitoring of water quality that depends majorly on examination of fecal indicator bacteria, thus protection of health requires fecal pollution indicator so that it is not required to analyze drinking water to overcome the problems associated with waterborne diseases. This paper will brief the classification, sources, survival of E. coli bacteria and its correlation with basic water quality parameters in water sources.```

MPC (Magneto-Photonic Crystal) Optimisation is a feature-rich Windows software application designed to enable researchers to analyze the optical and magneto-optical spectral properties of multilayers containing gyrotropic constituents. A set of computational algorithms aimed at enabling the design optimization and optical or magneto-optical (MO) spectral analysis of 1D magnetic photonic crystals (MPC) is reported, together with its Windows software implementation. Relevant material property datasets (e.g., the optical spectra of refractive index, absorption, and gyration) of several important optical and MO materials are included, enabling easy reproduction of the previously published results from the field of MPC-based Faraday rotator development, and an effective demonstration-quality introduction of future users to the multiple features of this package. We also report on the methods and algorithms used to obtain the absorption coefficient spectral dispersion datasets for new materials, for which the film thickness, transmission spectrum, and refractive index dispersion function are known.

Over the last decades, the coated glass products, and especially the low-emissivity coatings have become a common building material used in modern architectural projects. More recently, these material systems became common in specialized glazing systems featuring solar energy harvesting. Apart from achieving the stability of optical parameters in multilayer coatings, it is also important to have improved control over the design of visual color properties of the coated glass. We prepare metal-dielectric composite (MDC) based multilayer thin-film structures using the RF-magnetron sputtering deposition and report on their optical and chromaticity properties in comparison with these obtained using pure metal-based Dielectric/Metal/Dielectric (DMD) trilayer structures of similar compositions. Experimentally achieved Hunter L, a, b values of MDC-based multilayer building blocks of coatings provide a new outlook on the engineering of future-generation optical coatings with better color consistency and developing approaches to broaden the range of achievable color coordinates and better environmental stability.

A study of photovoltaic solar window technologies is reported, focusing on their structural features, functional materials, system development, and suitability for use in practical field applications, e.g. public infrastructures and agricultural installations. Energy generation performance characteristics are summarized and compared to theory-limit predictions. Working examples of pilot-trial solar window-based installations are described. We also report on achieving electric power outputs of about 25 W_p/m² from clear and transparent large-area glass-based solar windows.

At present, the world is now passing a very far different time than normal situation due to the COVID-19 pandemic crisis. The global life-style and human civilization is currently progressing with down-stream that affecting almost every sectors necessary for human civilizations except the current environmental situation. To control the COVID-19 spreading, most of the countries are following lockdown process that reduces human mobility, thus reducing the CO2 emission to the environment. Though the COVID-19 pandemic is a blessing for the present environment, however, the post-COVID world will face a massive thrust of energy and only conventional energy resources may not be enough to mitigate the energy demands. Solar power generation technology mainly the photovoltaic (PV) systems and their advancement can be the leading possibilities to minimize the gap between the power demand and generation. It is now time to think how we can improve the PV power generation in future and the post-COVID world. In this encyclopaedia communication, we report on Nano-technological approach to improve the conversion efficiency of GaAs solar cells. We have designed and optimized several types of nano-structured assemblies that can be implemented to reduce the front surface incident light reflection losses thus can assist to improve the conversion efficiency of GaAs solar cells.

We present a review of the current state of the field for a rapidly evolving group of technologies related to solar energy harvesting in built environments. In particular, we focus on recent achievements in enabling the widespread distributed generation of electric energy assisted by energy capture in semi-transparent or even optically clear glazing systems and building wall areas. Whilst concentrating on the cutting-edge recent results achieved in the integration of traditional photovoltaic device types into novel concentrator-type windows and glazings, we compare the main performance characteristics reported with these achievable using more conventional (opaque or semi-transparent) solar cell technologies. A critical overview of the current status and future application potential of multiple existing and emergent energy harvesting technologies for building integration is provided.

Amorphous ferrite-type rare-earth (RE) substituted garnets and garnet-oxide nanocomposite layers are prepared on clear glass substrates by using RF magnetron sputter-deposition process. By using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method, the spectral dispersion function of optical constants and the layer thicknesses are derived accurately from the transmission spectra of the as-deposited samples. The effects of excess metal-oxides added to the base material systems during the co-deposition process are found to affect the refractive index and the optical absorption coefficients of garnet-oxide composites. A number of optical constant datasets are presented, enabling the experimentalists to design nanophotonic or integrated-optics devices employing these functional materials.

In the field of business environments, the integration of novel artificial intelligence (AI) techniques has been identified in the literature and theoretical discourse as an essential catalyst for enhancing the decision-making processes. In the contemporary landscape of digital transformation, the application of these techniques becomes essential, despite encountering various hurdles that impede their seamless integration into the rational decision-making process within e-government, which constitutes a critical component of digital government initiatives. This study explores whether similar advancements can be observed within the e-government sector and investigates the impact of using machine learning (ML) as a technique of artificial intelligence on rational decision-making (RDM). Employing an empirical research approach, the study utilized a quantitative methodology, relying on an electronically structured questionnaire survey administered to 163 employees in the e-government sector in Jordan through purposive random sampling. Data analysis was conducted using the SPSS v25 program, complemented by a media-tion analysis using AMOS v23 software. The research findings revealed a significant contribution of using machine learning to enhance rational decision-making and trust levels, with trust positively impacting RDM. Trust was identified as a beneficial mediator in the relationship between machine learning and rational decision-making. Despite certain limitations, this study's outcomes offer substantial insights for researchers and government policy-makers alike, contributing to the advancement of sustainable practices in the e-government domain.

This paper addresses the conceptual exploration of various issues that form an integral part of the ethical dimensions surrounding the use of artificial intelligence (AI) in the field of marketing. We critically review some of the main ethical challenges AI poses to humanity: privacy, data security, bias, transparency, and accountability. Therefore, we will discuss the delicate balance between exploiting the transformation potential of AI for personally designed marketing strategies and ethical imperatives to safeguard the rights of consumers to retain trust. Then, the present regulatory landscape responding to these ethical challenges will be assessed by building on effective regulation, like the GDPR, existing proposed legislative frameworks, and industry guidelines. To underscore the role of an ongoing dialogue between marketers, technologists, ethicists, and regulators for developing a responsible AI ecosystem in marketing. Further, strategic recommendations for implementing company-based ethical AI marketing practices. The further strong guidelines provide enhancement transparency to consumers and investment in research to remove biases from algorithms. It also underscores principal scopes of further research and development, focusing on the need for new-age solutions to guide the ethical quagmires that AI-led marketing throws up. We suggest that integration should be done proactively and collaboratively. Thus, if attention is paid more to ethics and multidisciplinary dialogue, only such hyperbolic promises can be realized by AI-driven marketing. There are such promises through which AI-driven marketing will meet business goals and be huge at societies' values.

In the recent century, the tourism industry and within it the tourism economy are one of the most important and fundamental sectors of engaged business. E-tourism can be used as a dynamic tool in up to date areas of informative information and tourism marketing will be considered as a suitable field for the tourism industry. The aim of this study was to investigate the relationship between climate change and the amount of revenues from the tourism industry relying on a tool called e-tourism, and informing and providing services through this way so that Iran can achieve a greater share of export of a single-product oil economy combined with economic growth and sustainable development goals. The method of this research is descriptive-analytical.

We report on the development of several different thin-film functional material systems prepared by RF magnetron sputtering at Edith Cowan University nanofabrication labs. We conduct research on the design, prototyping, and practical fabrication of high-performance magneto-optic (MO) materials, oxide based sensor components, and heat regulation coatings for advanced construction and solar windows.

Since 2007, at the Electron Science Research Institute (ESRI) nano-fabrication laboratories, Edith Cowan University, Australia, we have devoted research efforts to the synthesis and characterization of bismuth-containing ferrite-garnet-type thin-film magneto-optic (MO) materials of different compositions. We report on the development and properties of highly bismuth-substituted iron-garnet thin films prepared by using radio frequency (RF) magnetron sputtering. We study the process parameters associated with the RF magnetron sputter deposition technique and investigate the results of optimizing process parameters and implementing several special techniques including the fabrication of co-sputtered nanocomposite films, all-garnet multilayer structures, applying oxygen plasma treatment on amorphous garnet layers just after the deposition process, and designing modifications of the annealing crystallization process and regimes for achieving the best MO properties. We demonstrated significant improvement in MO properties of Bi-containing ferrite-type garnet thin-film materials, including record-high MO figures of merit and improved conventional and un-conventional hysteresis loops of Faraday rotation. The attractive optical, magnetic, and magneto-optic properties obtained in highly bismuth-substituted iron garnet thin-film materials of multiple composition types are relevant in the context of manufacturing next-generation ultra-fast optoelectronic devices, such as light intensity switches and modulators, high-speed flat panel displays, and high-sensitivity sensors.

We report on the field testing datasets and performance evaluation results obtained from a commercial property-based visually-clear solar window installation site in Perth-Australia. This installation was fitted into a refurbished shopping centre entrance porch, and showcases the potential of glass curtain wall-based solar energy harvesting in built environments. In particular, we focus on photovoltaic (PV) performance characteristics such as the electric power output, specific yield, day-to-day consistency of peak output power, and the amounts of energy generated and stored daily. The dependencies of the generated electric power and stored energy on multiple environmental and geometric parameters are also studied. An overview of the current and future application potential of high-transparency, visually-clear solar window-based curtain wall installations suitable for practical building integration is provided.

The exploration of alternative antimalarial therapeutics is a requisite for the emergence of resistance against Artemisinin. Considering the required cost and time length of classical small molecule drug discovery process, phytochemical screening of traditionally used medicinal plant which are repertoire of active compounds with antimalarial activity has become popular. To investigate the antimalarial property of traditionally used medicinal plants, a number of Erythrina spp have been reviewed systematically where less studied E. fusca has been selected for further analysis. Phytochemical investigation yielded five compounds namely; Phaseolin, Phytol, β-amyrin, Lupeol, and Stigmasterol. In-vitro antimalarial drug sensitivity HRP-II ELISA was carried out against chloroquine (CQ) sensitive 3D7 and CQ-resistant Dd2 strains. Extracts showed significant antimalarial activity against 3D7 and Dd2 strains (IC₅₀ 4.94 – 22 µg/mL) and these compounds have been reported here for the first time. Molecular docking analysis showed high binding energy (−9.0 ± 0.32 kcal/mole) indicating high degree of interaction between Phaseolin and 14 clinically important Plasmodium falciparum proteins at the active site. Stable interaction was also observed between ligand and protein from molecular dynamics simulation analysis with high free energy (−75.156 ± 11.459) that substantiates the potential of Phaseolin as an antimalarial drug candidate.

Current VAT rules for cross-border e-commerce companies in the EU are not sustainable, because they are extremely complex and often opaque, due to the lack of tax harmonization. The aim of the research is to explore, using a qualitative method, what kind of harmonization would make the current legislation more uniform, simpler, more transparent, and easier to understand, without conflicting with the rules of any Member State. To this end, the aspects of the new platform regulation introduced on 1 July 2021 and its potential for expansion are assessed through information from possible sales models. The research suggests that the rules on platforms do not cover all possible sales models, which in our view imposes an unnecessary extra administrative burden on some businesses and makes their tax activities less transparent. In the light of the results of the research, we propose that the current EU platform regulation should be extended to cover B2B, B2C transactions and services. As a result of this suggested harmonization, a simpler, more transparent, uniform and sustainable tax system would contribute to the whitening of the economy, generating additional tax revenue for Member States.

With the dramatic increase in world population, continued advances in modern greenhouse agriculture and plant growth practices are expected to help overcome the global problem of future food shortages. Next generation greenhouse design practices will need to address a range of issues, ranging from energy and land use efficiency to providing plant-optimised growth techniques. In this paper, we focus on investigating the optimum irradiation spectra matched to the lettuce species (Lactuca sativa, L.), which is commonly grown in greenhouse environments, in order to develop low-emissivity glass panes that maximize the biomass productivity of glass greenhouses. This low-emissivity glass passes the solar spectral components needed for crop growth, while rejecting other unwanted radiations, leading to significant energy savings and other beneficial effects related to greenhouse climate control, in a range of climates. This is due to reducing both the solar heat gain and photosaturation, which can raise the temperature of the crops to harmful levels. Experimental results show that substantial biomass productivity improvements in lettuce (up to ~14.7%) can be attained using spectrally optimized illumination, compared with white light irradiation. We also report on the development of advanced metal-dielectric thin-film filters that produce the optimum illumination spectrum when exposed to sunlight.

The devastating COVID-19 pandemic forced academia to go virtual. Educational institutions around the world have stressed online learning programs in the aftermath of the pandemic. However, because of insufficient access to ICT, a substantial number of students failed to harness the opportunity of online learning. This study explores the latent digital divide exhibited during the COVID-19 pandemic while online learning activities are emphasized among Bangladeshi students. It also investigates the digital divide exposure and the significant underlying drivers of the divide. A cross-sectional survey was employed to collect quantitative data mixed with open-ended questions to collect qualitative information from the student community. The findings revealed that despite the majority of students have physical access to ICT but only 32.5% of students could attend online classes seamlessly, 34.1% of the students reported the data prices as the critical barrier, and 39.8% of students identified the poor network infrastructure is the significant barrier for them to participate in online learning activities. Although most students possess physical access to the device and the Internet, they face the first-level digital divide due to the quality of access and maintaining subscriptions. Consequently, they fail to take advantage of physical access, resulting in the third-level digital divide (Utility Gap) and submerging them into a digital divide cycle. This paper aimed to explore the underlying issues of the digital divide among Bangladeshi students to assist relevant stakeholders (e.g., the Bangladesh government, Educational Institutions, Researchers) in providing the necessary insights and theoretical understanding to arrange adequate support for students to undertake conducive online learning activities.

Introduction: Left atrial hypertension is one of the pathophysiologies of heart failure with preserved ejection fraction. We hypothesized that left atrial pressure response (LAPR) to incremental pacing is higher in patients with atrial fibrillation (AF) and can predict left ventricular diastolic dysfunction. Methods: Patients requiring left atrial access as a part of a therapeutic procedure for AF (n=204, AF group) or supraventricular tachycardia (n=34, control group) were analyzed (male n=183, 54±12 years old). LAPR was measured during incremental pacing. Results: Baseline left atrial pressure and LAPR at all pacing rates were not different between the AF and control groups. They were higher in patients with a high E/e’ (≥ 8) than in those with a low E/e’ (< 8). LAPR at a pacing interval of 400ms and E/e' were positively correlated (r=0.373, p<0.001). Body mass index and a high E/e' were independent predictors of pacing-induced left atrial hypertension. Conclusions: The LAPR to incremental pacing was constant regardless of AF. The non-invasive echocardiographic marker E/e' reflected pacing-induced left atrial hypertension.

Hepatitis E virus (HEV) is a common cause of acute hepatitis worldwide, accounting for approximately 25% of deaths among pregnant women. We previously reported that pregnancy serum facilitates HEV replication in vitro. However, the differences in host cells with HEV infection induced by pregnancy serum and fetal bovine serum (FBS) are unclear. In this study, differentially expressed proteins were identified in HEV-infected hepatoma cells (HepG2) supplemented with different sera by using isobaric tags for relative and absolute quantitation. Proteomic analysis indicated that HEV infection significantly induced 1014 differentially expressed proteins in HEV-infected HepG2 cells when supplemented with FBS compared with pregnancy serum. Further validation by Western blot confirmed that filamin A, heat-shock proteins 70 and 90, Cytochrome c, and Thioredoxin were associated with HEV infection. This comparative analysis provides an important basis to further investigate HEV pathogenesis in pregnant women and HEV replication.

Purpose: The purpose of this study is to further explore how e-loyalty and E-marketing influences E-trust and satisfy the demand by offering fresh perspectives based on research as well as emphasis on the factors influencing the E-trust such as culture as a mediator. This study not only contributed theoretically but also presented practical implementations. Design/methodology/approach: Online survey was used to obtain data by focusing the Hospitality sector (Hotel Industry) and verifying the conceptual framework. Data was collected in multiple time lags. Findings: Findings showed that the E-trust influenced by E-loyalty and E-Marketing. E-trust comes from the previous experiences, e-loyalty and e-marketing. Further, some trends such as culture influenced the e-trust. Research limitation/implications: The present study is quite suitable for those Researchers interested in learning more about the effects of E-loyalty and E-marketing on user E-trust and how to mitigate cultural influences can benefit from the current study. This research also has implications for those who wish to improve market allure and survival in digital world. This study focused on the hospitality sector (Hotel Industry) in China; however, the sector and geography could be altered to suit the needs of the study's participants. Practical implications: The present study delivers the practical guidelines which are quiet suitable for understanding the formation of E-loyalty, E-marketing, and E-trust through which specific E-marketing strategy can be designed to deal with the consumer’s E-loyalty and their expectations as per their Cultural perspective. At some particular regions/countries, cultural trends are more important than practical market. This research study practically showed that how culture changed the consumer set of mind. Originality/value: The relationship between E-loyalty, E-marketing, E-trust, specifically with the cultural influence in digital market has been the subject of few research.

This work is devoted to physical vapor deposition synthesis, and characterisation of bismuth and lutetium-substituted ferrite-garnet thin-film materials for magneto-optic (MO) applications. The properties of garnet thin films sputtered using a target of nominal composition type Bi_0.9Lu_1.85Y_0.25Fe_4.0Ga₁O₁₂ are studied. By measuring the optical transmission spectra at room temperature, the optical constants and the accurate film thicknesses can be evaluated using Swanepoel’s envelope method. The refractive index data are found to be matching very closely to these derived from Cauchy’s dispersion formula for the entire spectral range between 300-2500 nm. The optical absorption coefficient and the extinction coefficient data are studied for both the as-deposited and annealed garnet thin-film samples. A new approach is applied for accurately deriving the optical constants data simultaneously with the physical layer thickness, using a combination approach employing custom-built spectrum-fitting software in conjunction with Swanepoel’s envelope method. MO properties, such as specific Faraday rotation, MO figure of merit and MO swing factor are also investigated for several annealed garnet-phase films.

We report on the study of energy-harvesting performance in medium-size (400 cm²) glass-based semitransparent solar concentrators employing edge-mounted photovoltaic modules. Systems using several different types of glazing system architecture and containing embedded diffractive structures are prepared and characterized. The technological approaches to the rapid manufacture of large-area diffractive elements suitable for use in solar window-type concentrators are described. These elements enable the internal deflection and partial trapping of light inside glass-based concentrator windows. We focus on uncovering the potential of pattern-transfer polymer-based soft lithography for enabling both the improved photon collection probability at solar cell surfaces, and the up-scaling of semitransparent solar window dimensions. Results of photovoltaic characterization of several solar concentrators employing different internal glazing-system structure and diffractive elements produced using different technologies are reported and discussed.

Magneto-optic (MO) imaging and sensing are at present the most developed practical applications of thin-film MO garnet materials. However, future component and system-level sensors and imagers technology improvements are still necessary in order to improve sensitivity for a range of established and also the forward-looking applications. These improvements are expected to originate from new material system development. We propose a set of technological modifications for the RF-magnetron sputtering deposition and crystallization annealing of magneto-optic bismuth-substituted iron-garnet films and investigate the improved material properties. Results show that standard crystallization annealing for the as-deposited ultrathin (sputtered 10 nm thick, amorphous phase) films resulted in more than a factor of two loss in the magneto-optical activity of the films in visible spectral region, compared to the liquid-phase grown epitaxial films. Results also show that an additional 10 nm-thick metal-oxide (Bi2O3) protective layer above the amorphous film results in ~2.7 times increase in the magneto-optical quality of crystallized iron-garnet films. On the other hand, the effects of post-deposition oxygen (O2) plasma treatment on the magneto-optical (MO) properties of Bismuth substituted iron garnet thin films material is investigated. Results show that, in the visible part of the electromagnetic spectrum (at 532 nm), the O2 treated (up to 3 minutes) garnet films retain higher specific Faraday rotation and figure of merit than those of non-treated garnet films.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

The development of biofuels and biodiesel industry specifically, has resulted in the generation of large amounts of glycerol as a surplus. The conversion of glycerol, into chemicals with indus-trial interest, through anaerobic fermentation using E. coli as a biocatalyst is an attractive alter-native to improve economic performance in the biodiesel industry, for example through the bi-otransformation of residual glycerol into ethanol. For 2019, the size of the global ethanol market was valued at $ 89.1 billion US dollar. Biodiesel can be produced from several materials like rapeseed, palm, soya, corn, palm kernel, frying oil or olive-pomace oil (OPO). The last, can be extracted from alperujo, byproduct of olive oil process. However, olive-pomace oil converting into biodiesel is not enough established to achieve a global olive-oil/biodiesel derived process with minimized waste generation. Traditionally biodiesel production process produces an equivalent of 10% by mass of glycerol as a waste or by-product. This work explores the conver-sion of residual glycerol into chemicals like ethanol and hydrogen with a focus on projecting raw material potential availability from OPO, contributing to the promotion of the use of biofu-els and biodegradable compounds.

The global rising demand for exploiting limited shared groundwater resources, coupled with significant water deficit, especially in arid and semi-arid regions, has led to escalating conflicts among stakeholders. As such, using Bankruptcy Theory methods can be an appropriate response to the reallocation of resources. This study introduces a novel approach to weighted Bankruptcy, where the relative importance of stakeholders is determined by their contributions to sustainable development, and the impact of their claims on the shared groundwater resources is considered. The framework is implemented in a two-level bankruptcy process including the plains and their beneficiaries (agriculture, drinking and industry). The proposed two-level weighted bankruptcy process applies to the Neyshabour-Ataiyeh-Sabzevar plains in Iran. The process is implemented for two scenarios including the Baseline scenario related to the present status of demands and the Future scenario associated with the estimated demands for the year 2041. To compare the weighted proposed method with the other weighted methods such as Proportional (WPRO), Constrained Equal Awards (WCEA), Pinile (WPIN), Talmud (WTAL), Constrained Equal Losses (WCEL), Modified Constrained Equal Losses (MWCEL), two categories including the deficit-based and resource-based approaches are considered. According to the stability analysis using the Bankruptcy Allocation Stability Index (BASI) method, among the deficit-based methods, the novel approach is chosen as the preferred method for the beneficiaries’ reallocation like the Sabzevar’s beneficiaries. Accordingly, it allocates 86.95%, 10.86% and 2.17% of the shared resource to the agricultural, drinking, and industrial demands, respectively. Among the resource-based methods, the WPIN method is selected for reallocation between the stakeholders and their beneficiaries in each level and scenario of reallocation. The novel approach offers a promising solution to the water resource reallocation problem, ensuring a more equitable and sustainable management of shared groundwater resources.

Protein tyrosine phosphatase receptor type E (PTPRE) is a member of the “classical” protein tyrosine phosphatase subfamily and regulates a variety of cellular processes in a tissue-specific manner by antagonizing the function of protein tyrosine kinases. PTPRE plays a tumorigenic role in different human cancer cells, but its role in retinoblastoma (RB), the most common malignant eye cancer in children, remains to be elucidated. Etoposide resistant RB cell lines and RB patients display significant higher PTPRE expression levels compared to chemosensitive counterparts and the healthy human retina, respectively. PTPRE promotor methylation analyses revealed that PTPRE expression in RB is not regulated via this mechanism. Lentiviral PTPRE knockdown (KD) induced a significant decrease in growth kinetics, cell viability, and anchorage independent growth of etoposide resistant Y79 and WERI RB cells. Caspase-dependent apoptosis rates were significantly increased and a re-sensitization for etoposide could be observed after PTPRE depletion. In vivo chicken chorioallantoic membrane (CAM) assays revealed decreased tumor formation capacity as well as reduced tumor size and weight following PTPRE KD. Expression levels of miR631 were significantly downregulated in etoposide resistant RB cells and patients. Transient miR631 overexpression resulted in significantly decreased PTPRE levels and concomitantly decreased proliferation and increased apoptosis levels in etoposide resistant RB cells, impacts mirroring PTPRE KD effects and indicating PTPRE regulation via this miR. Additionally, PTPRE KD led to altered phosphorylation of protein kinase SGK3 and - dependent on the cell line - also AKT and ERK1/2, suggesting potential PTPRE downstream signaling pathways. In summary, these results indicate an oncogenic role of PTPRE in chemoresistant retinoblastoma.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

Smartphones are prone to SMS phishing due to the rapid growth in the availability of smart mobile technologies driven by Internet connections. Also, detecting phishing SMS is a challenging task due to the unstructured nature of SMS text data with non-linear complex correlations. In this concern, considering the recent advancements in the domain of cybersecurity, we have proposed a hybrid deep learning framework that extracts robust features from SMS texts followed by an automatic detection of Phishing SMS. Due to combining the potential capability of individual models into one hybrid framework, it has outperformed various other individual machine learning and deep learning models. The proposed Phishing Detection framework is an effective hybrid combination of pretrained transformer model, MPNet (Masked and Permuted Language Modeling), with supervised ConvNets (CNN) and Bi-directional Gated Recurrent Units (GRU). It is intended to successfully detect unstructured short phishing text messages that contain complex patterns.

Several pathotypes of enteric E. coli have been identified. The group represented by Shiga toxin-producing E. coli (STEC) is of particular interest. Raw milk and raw milk products are significant sources of STEC infection in humans; therefore, identifying pathogens at the herd level is crucial for public health. Most national surveillance programs focus solely on raw milk and raw milk cheeses that are ready for retail sale, neglecting the possibility of evaluating the source of contamination directly at the beginning of the dairy chain. In order to assess the viability of new molecular methodologies applied to raw milk filters enabling the identification of the presence of STEC serotypes in milk production and apply the same methods to identify the presence of these pathogens in calf feces we analyzed, through a commercial real-time PCR assay, a total of 290 samples coming from 18 different dairy herds; 88 bulk tank milk (BTM), 104 raw milk filters (RMF) and 98 calves’ feces samples. In total 3.4% of BTM, 41.4% of RMF and 73.4% of calves’ feces tested positive for stx presence, supporting our hypothesis that BTM is not a suitable matrix to assess the STEC presence at herd level, underestimating it. Our conclusion is that the surveillance program needs critical and extensive improvements such as RMF and calves’ feces analysis implementation in order to be more efficient in detecting and preventing STEC infections. The epidemiology of these infections and the characteristics of the pathogen clearly show how a One Health approach will be pivotal to improve our capabilities to control the spread of these infections.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

In recent years, many libraries and archives have started digitizing their collections thus making maps by Indigenous peoples more easily available for scholars to study. While a number of these maps were discussed by G. Malcolm Lewis in the History of Cartography series (volume 2, book 3, Chapter 4: 1984), more have since been found and disseminated. These maps are critical in understanding the historic and current land tenure of Indigenous groups. Further, Indigenous claims to land can be seen in their connections via toponymy. European concepts of territory and political boundaries did not coincide with First Nation/American Indian views resulting in the mistaken view that Natives did not have formal concepts of their territories. Further, Tribes/First Nations with cross-border territory have special jurisdictional problems. This paper will illustrate how many Native residents were very spatially cognizant of their own lands, as well as neighboring nations’ lands, overlaps between groups, hunting territories, populations, and trade networks. Currently, the Sinixt First Nation provides a perfect example of how an Aboriginal people are inputting and using a GIS representation of their territory with proper toponymy and use areas.

Background and Objectives: In recent years Electronic scooters (E-Scooters) have gained popularity, whether for private use or as a publicly available transportation method. With introduction of these vehicles, reports of E-Scooter related accidents have surged, sparking a public debate and concern. Aim of this study was to analyse epidemiological data, characteristics and severity of traumatic brain injury (TBI) related to E-Scooter accidents. Materials and Methods: This retrospective case series evaluated 28 patients who were admitted to three largest neurosurgery clinics in Riga, Latvia between time period from April to October in two separate years – 2022 and 2023 after an E-Scooter related accident. Data were collected on patient demographics, time of the accident, alcohol consumption, helmet use, type of TBI, other related injuries, treatment and assessment at discharge. Results: A total of 28 patients were admitted with TBI related to E-Scooter use, with median age 30 years (Q1-Q3, 20.25-37.25), four individuals under age of 18, majority (64%) were male. In 23 cases the injury mechanism was fall, in 5 cases collision. None were wearing a helmet at time of injury. Alcohol intoxication was evident in over half of the patients (51.5%), with severe intoxication (>1.2ppm) in 75% cases among them. Neurological symptoms upon admission were noted in 50% of cases. All patients had intracranial trauma - 50% brain contusions, 43% traumatic subdural hematoma, almost 30% - epidural hematoma. Craniofacial fractures were evident in 71% of cases, fractures in other parts of body in 3 patients. 6 patients required emergency neurosurgical intervention. Neurological complications were noted in 2 patients, 1 patient died. Conclusions: E-Scooter related accidents result in a significant number of brain and other associated injuries, with notable frequency linked to alcohol influence and lack of helmet use. Prevention campaigns to raise awareness of potential risks and implementation of more strict regulations should be done.

Coronavirus disease 2019 (COVID-19) displays clinical heterogeneity, but little information is available for patients with mild or very early disease. We aimed to characterize biomarkers that are useful in discriminating the hospitalization risk in a COVID-19 cohort from Northern Italy during the first pandemic wave. We enrolled and followed for four weeks 76 symptomatic SARS-CoV-2 positive patients and age/sex-matched healthy controls. Patients with mild disease were discharged (n.42), and the remaining were hospitalized (n.34). Blood was collected before any anti-inflammatory/immunosuppressive therapy and assessed for soluble C5b-9/C5a, H3-neutrophil extracellular traps (NET), calprotectin, DNase plasma levels by ELISA, and a panel of pro-inflammatory cytokines by ELLA. Calprotectin and NET levels discriminate between hospitalized and non-hospitalized patients, while DNase negatively correlates with NET levels; there are positive correlations between calprotectin and both NET and neopterin levels. Neopterin levels increase in patients at the beginning of the disease and more in hospitalized than non-hospitalized ones. C5a and sC5b-9, and other acute phase proteins correlate with neopterin, calprotectin, and DNase. Both NET and neopterin levels negatively correlate with platelet count. We show that calprotectin, NET, and neopterin are important proinflammatory parameters potentially useful in discriminating between COVID-19 patients at risk for hospitalization.

This study employs a high-fidelity numerical framework to determine the plastic material flow patterns and temperature distributions that lead to void formation during friction stir welding (FSW), and to relate the void morphologies to the underlying alloy material properties and process conditions. Three aluminum alloys, viz., 6061-T6, 7075-T6, and 5053-H18 were investigated under varying traverse speeds. The choice of aluminum alloys enables investigation of a wide range of thermal and mechanical properties. The numerical simulations were validated using experimental observations of void morphologies in these three alloys. Temperatures, plastic strain rates, and material flow patterns are considered. The key results from this study are: (1) The predicted stir zone and void morphology are in good agreement with the experimental observations, (2) The temperature and plastic strain-rate maps in the steady-state process conditions show a strong dependency on the alloy type and traverse speeds, (3) The material velocity contours provide a good insight into the material flow in the stir zone for the FSW process conditions that result in voids as well as those that do not result in voids. The numerical model and the ensuing parametric studies presented in this work provide a framework for understanding material flow under different process conditions in aluminum alloys, and potentially in other alloys. Furthermore, the utility of the numerical model for making quantitative predictions and investigating different process parameters to reduce void formation is demonstrated.

One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

Oncogenic protein E6 from Human Papilloma Virus 16 (HPV-16) mediates the degradation of Membrane-associated guanylate kinase with inverted domain structure-1 (MAGI-1), throughout the interaction of its protein binding motif (PBM) with the Discs-large homologous regions 1 (PDZ1) domain of MAG1-1. Generic variation in the E6 gene that translates to changes in the protein’s amino acidic sequence modifies the interaction of E6 with the cellular protein MAGI-1. MAGI-1 is a scaffolding protein found at tight junctions of epithelial cells, where it interacts with a variety of proteins regulating signaling pathways. MAGI-1 is a multidomain protein containing two WW (rsp-domain-9), one guanylate kinase-like, and six PDZ domains. PDZ domains played an important role in the function of MAGI-1 and served as targets for several viral proteins including the HPV-16 E6. The aim of this work was to evaluate, with an in silico approach, employing molecular dynamics simulation and protein-protein docking, the interaction of the intragenic variants E-G350 (L83V), E-C188/G350 (E29Q/L83V), E-A176/G350 (D25N/L83V), E6-AAa (Q14H/H78Y/83V) y E6-AAc (Q14H/I27RH78Y/L83V) and E6-reference of HPV-16 with MAGI-1. We found that variants E-G350, E-C188/G350, E-A176/G350, AAa and AAc increase their affinity to our two models of MAGI-1 compared to E6-reference.

Coarse-grained molecular dynamics simulations are employed to investigate the spatiotemporal evolution of vesicles (polymersomes) by the self-assembly of randomly distributed amphiphilic BAB triblock copolymers with hydrophilic A and hydrophobic B blocks in an aqueous solution. The vesiculation pathway consists of several intermediate structures, such as an interconnected network of copolymer aggregates, a cage of cylindrical micelles and a lamellar cage. The cage-to-vesicle transition occurs at a constant aggregation number and practically eliminates the hydrophobic interfacial area between the B block and solvent. Molecular reorganization under-lying the sequence of morphology transitions from a cage-like aggregate to a vesicle is nearly isentropic. The end-to-end distances of isolated copolymer chains in solution and those within a vesicular assembly follow log normal probability distributions. This is attributed to the pre-ponderance of folded chain configurations in which the two hydrophobic end groups of a given chain stay close to each other. However, the probability distribution of end-to-end distances is broader for chains within the vesicle as compared to that of a single chain. This is due to the swelling of the folded configurations within the hydrophobic bilayer. Increasing the hydropho-bicity of the B block reduces the vesiculation time without qualitatively altering the self-assembly pathway.

In this paper, we compile the fractional power series method and the Laplace transform to design a new algorithm for solving the fractional Volterra integro-differential equation. For that, we assume the Laplace power series (LPS) solution in terms of power q=1m,m∈Z+, where the fractional derivative of order α=qγ for which γ∈Z+. This assumption will help us to write the integral, the kernel, and the nonhomogeneous terms as a LPS with the same power. The recurrence relations for finding the series coefficients can be constructed using this form. To demonstrate the algorithm's accuracy, the residual error is defined and calculated for several values of the fractional derivative. Two strongly nonlinear examples are discussed to provide the efficiency of the algorithm. The algorithm gains powerful results for this kind of problem. Under Caputo meaning the obtained results are illustrated numerically, and graphically. Geometrically, the behavior of the solution declares that the changing of the fractional derivative parameter values' in their domain alters the style of the attained solution in a symmetrical meaning and fully coinciding to the ordinary derivative value'. From these simulations, the results report that the recommended novel algorithm is a straightforward, accurate, and superb tool to generate analytic-approximate solutions for Integral, and integro-differental equations of fractional order.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

This study introduces a novel nanocomposite coating composed of PANI/CeO2 nanocomposite films, aimed at addressing corrosion protection needs. Analysis through FTIR spectra and XRD patterns confirms the successful formation of the nanocomposite films. Notably, the PANI/CeO2 nanocomposite films exhibit a hydrophilic nature. The bandgap energy of the PANI composite film measures at 3.74 eV, while the introduction of CeO2 NPs into the PANI matrix reduces the bandgap energy to 3.67 eV. Furthermore, the electrical conductivity of the PANI composite film is observed to be 0.40 S.cm-1, with the incorporation of CeO2 NPs leading to an increase in electrical conductivity to 1.07 S.cm-1. To evaluate its efficacy, electrochemical measurements were conducted to assess the corrosion protection performance. Results indicate a high protection efficiency of 92.25% for the PANI/CeO2 nanocomposite film.

The issue of water and energy crisis have been turned into global matters which need to be tackled jointly. Accordingly, floating solar power plants, in which photovoltaic modules are used on the surface of water infrastructures, has recently been attracting much interest. This system provides some additional advantages over the ground-based system such as conserving the land and the water and increasing the efficiency of the module. This study first reviews the relevant literature comprehensively and then evaluates the potential of using floating solar photovoltaic (FSPV) on some of Iran’s water infrastructures which have experienced a large amount of evaporation every year due to high solar radiation. To this end, the five important dam reservoirs are selected as the representatives of the five important watersheds in Iran, and the advantages of the FSPV plant is analyzed in terms of energy generation, evaporation reduction, economic and environmental aspects considering different coverage percentages of reservoir’s surfaces. Considering Iran's vast potential for solar radiation, and, on the other hand, huge energy demand and critical water situation, results indicated that Iran can effectively harness solar energy through FSPV systems which help conserve the water in addition to support sustainable energy production.

Semisolid casting can provide excellent castings, but the nature of the pore-forming mechanisms has not been properly clarified. In the current communication, it was suggested that hydrogen precipitated during slurry making might have a decisive role in the formation of both gas and shrinkage porosity. Intensive stirring at the end of the slurry making process may act as a degassing step. Without the intense stirring, structures of primary slurry particles form around the hydrogen pores, strongly affecting pore formation and feeding during the intensification stage.

Modern organic synthesis is majorly focused on developing environmentally benign synthetic protocols by employing green chemistry principles. Accordingly, in our recent research work, we herein report the use of modified supramolecular host cyclodextrin as an effective solid based green catalyst for accessing structurally diverse and medicinally relevant pyrimidone architectures. The catalyst and the synthesized compounds 4 (a-r) were characterized using FT-IR, NMR and GC-Mass spectroscopy. Major highlights of the reported work include: atom economical process, extremely milder reaction conditions, operational simplicity, high isolated yields, and excellent catalyst turnover number. The molecular docking studies suggest that the compound 4n has the hydrogen bonding, hydrophobic and π-pair interactions with the active site of active sites of CXT M 15 receptor.

The speed-density or flow-density relationship is a fundamental aspect of traffic flow theory. Single-regime models often face challenges in consistently fitting empirical data under diverse traffic conditions. This paper addresses the inaccuracies of single-regime models, attributing them not only to their functional forms but also to data dispersion and sample selection bias. To mitigate these issues, the data is segmented into day and night periods, leading to the creation of separate models for each. Calibration results, conducted on data from two freeways, Tehran-Karaj and Tehran-Qom, reveal distinct challenges, with the former exhibiting high dispersion and the latter showing low dispersion. Surprisingly, single-regime models demonstrate notable effectiveness when applied to distinct day and night data. Further analysis, categorizing data into day and night, results in reduced errors (20-60% improvement in R-Square), emphasizing the potential for enhanced accuracy by considering distinct regimes. Overall, the study underscores the significance of regime-specific considerations for accurate traffic flow modeling. Upon thorough evaluation, the study highlights the superiority of the neural network Multi-layer Perceptron (MLP) over traditional models. The research discusses the implications of incorporating day and night parameters into the models, emphasizing their potential for accuracy enhancement.

In dry season paddy farming, the alternate wetting and drying (AWD) irrigation improves water productivity, paddy production, and has the potential to decrease greenhouse gas (GHG) such as methane (CH4) and nitrous oxide (N2O) emissions when compared to continuous flooding (CF). However, there is a lack of research in Bangladesh on the effects of water management on CH4 and N2O emissions. During November 2017–April 2018, participatory on-farm trials were conducted at Feni and Chattogram districts of Bangladesh. Total 105 farmers comprising 20-hectare of land (62 farmers at Feni and 43 farmers at Chattogram district, each location having 10 hectare of land). We compared irrigation water and cost reductions, paddy yield, and CH4 and N2O emissions from paddy fields irrigated using AWD and CF irrigation methods. The CH4 and N2O emissions were determined using the Cool Farm Beta-3 methodology, and the global warming potential (GWP) was estimated using the Intergovernmental Panel on Climate Change-2014 standard approach. The mean results of randomly selected 30 farmers from two locations (15 of each) showed that AWD remarkably decreased irrigation water consumption by about 24% and increased water productivity by 224%. We estimated 23% savings for irrigation costs in AWD. By this time, AWD improved paddy production by 3% over CF. The AWD irrigation resulted in a 47% reduction in cumulative CH4 emissions having a lower CH4 emission factor (0.74 kg ha-1 day-1) than CF (1.39 kg ha-1 day-1). There was no obvious difference in N2O emission between AWD and CF. When compared to CF, AWD decreased the overall GWP by 27% and lowered the GHG intensity by 42%. The CH4 and N2O emissions did not differ substantially between Feni and Chattogram.

In the last decade Electromagnetic Induction (EMI) measurements have been increasingly used for investigating the soil salinization caused by the use of brackish or saline water as irrigation source. EMI measurements proved to be a powerful tool for providing spatial information of the investigated soil because of the strict correlation between the output geophysical parameter, i.e. the electrical conductivity, to soil moisture and salinity. In addition, their non-invasive nature and their capability to collect a high number of data over broad areas and in relatively short time, makes these measurements attractive for monitoring flow and transport dynamics, otherwise undetectable with conventional measurements. In an experimental field, EMI measurements were collected during the growth season of the tomato, irrigated with three different irrigation strategies. The data were collected over three months in a time-lapse mode in order to visualize changes in electrical conductivity to be associated with soil salinity. A rigorous time-lapse inversion procedure has been set for modeling the soil salinization induced by brackish irrigation water.

There is a case about a system comprising two queues of M/M(a)/1/K with a due date with FCFS service policy in each queue. Using the methods of simulation and mathematical analysis, the solution diagrams were illustrated for the fixed due date Ɵ=1 second at the phase of due date up to the commencement of the service, limited capacity K₁=5 and K₂=4, for both scenarios of different service management rate resulted. For the analytical solution, first, a SAN model from the system was created in the Mobius tool. For simulation, a java discrete systems simulation code was used. Adjustment of the initial values, selection of the scenarios for service rate, the number of the consumers in the simulation, etc. were all carried out in the simulation code.

Water scarcity is a significant challenge facing Jordan today. It is a challenge in all areas that use water, and it has become certain that water is the critical factor in the population/resources equation. The water resources in Jordan have become limited with the noticeable increase in the population, mostly resulting from forced migrations in neighboring countries because of the wars and until our time. The rising natural population growth rate, along with the massive influx of refugees, has turned into a state of disproportion between the daily consumption of the population and the amount of water available. That Jordan shares most of its surface water resources with neighboring countries has exacerbated the situation. The current use of water already exceeds its renewable supply. Excessive withdrawal from aquifers, which leads to a lowering of the water table and deterioration in water quality, covered the deficit. This paper focuses on assessing the water situation in Jordan, mainly evaluating this problem and the solution being considered, the true basis for a sustainable water solution requires awareness by the population, and several governmental and non-governmental organizations are actively involved in educating residents about water shortages. The most important and 'actionable' elements of comprehensive water solutions are discussed in this paper, and these elements exist, develop extra water supplies, water harvesting, water desalination, proper wastewater reuse in the agricultural sector, and reduce the demand for drinking water. This research provides specific recommendations to address the shortage of water resources in the Kingdom and highlights the importance of water conservation and optimal use.

Silencing of the fragile X mental retardation 1 (FMR1) gene and consequently lack of synthesis of FMR protein (FMRP) are associated with fragile X syndrome, which is one of the most prevalent inherited intellectual disabilities. FMRP is a multifunctional protein involved in many cellular functions in nearly all subcellular compartments under normal conditions and under conditions of cellular stress in both neuronal and non-neuronal cell types. This is achieved through its trafficking signals, nuclear localization signal (NLS), nuclear export signal (NES), and nucleolar localization signal (NoLS), as well as its RNA and protein binding domains, and is modulated by various post-translational modifications such as phosphorylation, ubiquitination, sumoylation, and methylation. This review summarizes recent advances in understanding the interaction networks of FMRP with a special focus on FMRP stress-related functions, including stress granule formation, mitochondrion and endoplasmic reticulum plasticity, ribosome biogenesis, cell cycle control, and DNA damage response.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

A convolutional neural network (CNN) is sometimes understood as a black box in the sense that while it can approximate any function, studying its structure will not give us any insights into the nature of the function being approximated. In other terms, the discriminative ability does not reveal much about the latent representation of a network. This research aims to establish a framework for interpreting the CNNs by profiling them in terms of interpretable visual concepts and verifying them by means of Integrated Gradient. We also ask the question, "Do different input classes have a relationship or are they unrelated?" For instance, could there be an overlapping set of highly active neurons to identify different classes? Could there be a set of neurons that are useful for one input class whereas misleading for a different one? Intuition answers these questions positively, implying the existence of a structured set of neurons inclined to a particular class. Knowing this structure has significant values; it provides a principled way for identifying redundancies across the classes. Here the interpretability profiling has been done by evaluating the correspondence between individual hidden neurons and a set of human-understandable visual semantic concepts. We also propose an integrated gradient-based class-specific relevance mapping approach that takes the spatial position of the region of interest in the input image. Our relevance score verifies the interpretability scores in terms of neurons tuned to a particular concept/class. Further, we perform network ablation and measure the performance of the network based on our approach.

According to the World Health Organization, approximately 20 million people worldwide are infected annually with the hepatitis E virus (HEV). There are 4 main genotypes of HEV. Genotype 1 and genotype 2 are common in developing countries and are transmitted by contaminated water from a fecal-oral route. Genotype 3 and genotype 4 are common in developed countries and can lead to occasional transmission to humans by undercooked meat. Hepatitis E virus 1 and HEV3 can lead to fulminant hepatitis, and HEV3 can lead to chronic hepatitis and cirrhosis in immunocompromised patients. The majority of patients with HEV infection are asymptomatic and usually have spontaneous viral clearance without treatment. However, infection in immunocompromised individuals can lead to chronic HEV infection. Both acute and chronic HEV infections can have extrahepatic manifestations. No specific treatment is required for acute HEV infection, no treatment has been approved in chronic infection and no HEV vaccine has been approved by the (United States) Food and Drug Administration. This review focuses on the molecular virology (HEV life cycle, genotypes, model systems, zoonosis), pathogenesis, clinical manifestation, and treatment of chronic HEV infection, especially in immunocompromised patients, to provide clinicians a better understanding of the global distribution of these infections and the significant effect they can have on immunocompromised patients.

Cardiovascular disease (CVD) is the leading cause of death worldwide. Cardiac rehabilitation (CR) has proven to be effective in reducing the rate of recurrence and disease as secondary prevention (evidence-based intervention) in patients who have suffered from myocardial infarction (MI). CR is a multidisciplinary path in which the patient is followed pharmacologically, from a psychological, nutritional, nursing and physiotherapy point of view. Post-MI patients present a reduction in the performance of the diaphragm muscle, the main inspiratory muscle, and this condition can become a risk factor for further relapses or for the onset of heart failure. Despite the solidity of the international guidelines for CR, the latter are lacking in specifically indicating an evaluation and training path regarding the inspiratory muscles in post-MI patients who have not undergone cardiac surgery. The article reviews the information on the adaptation of the diaphragm post-MI and highlights the need for clearer indications for a rehabilitation process that gives importance to the diaphragm.

As customer demand for green products increases in the digital economic era, this study analyses the green innovation of the e-tailer and supplier in drop shipping models. Moreover, drop shipping e-tailers and suppliers with a drop shipping option need to make choices regarding whether to provide green or normal products to the market. When a supplier with a drop shipping option produces green products, more fees may be invested on the production of green products than on normal products. The drop shipping e-tailers and suppliers with a drop shipping option can also choose to sell normal products at a low cost, as before. This study designs four models of drop shipping e-teilers and suppliers with a drop shipping option under different choices, analyzes their operational process in drop shipping models, and investigates five theorems. The optimal pricings decisions and green degree of drop shipping e-tailers and suppliers with a drop shipping option were evaluated in this study. The impacts of the green innovation factor, green elasticity coefficient, manufacturing and distribution costs on the drop shipping e-tailers and suppliers with a drop shipping option, and the effect of other environmental parameters on the green degree of green products are also analyzed through computer simulation. The findings of the simulation analysis provide valuable guidance for e-tailers and suppliers with green innovation in drop shipping models and offer important academic and practical implications for e-commerce and the digital economy.

Whistler mode waves play a major role in regulating the lifetime of trapped electrons in the Earth's radiation belts. Specifically, whistler mode hiss waves are one of the mechanisms that maintains the slot region between the inner and outer radiation belts. The generation mechanism of hiss is a topic still under debate with at least three prominent theories present in the literature. Lightning generated whistlers in their ducted or non-ducted modes, are considered to be one of the possible sources of hiss. We present a study of new observations from the Radio Receiver Instrument (RRI) on the Enhanced Polar Outflow Probe (ePOP: currently known as SWARM-E). RRI consists of two orthogonal dipole antennas, which enables polarization measurements, when the satellite boresight is parallel to the geomagnetic field. Here we present 75 passes of ePOP - RRI from 2014 - 2018, in which lightning whistlers and hiss waves were observed. In more than 50% of those passes hiss is found to co-exist with the lightning whistlers. Moreover, the whistler observations are correlated with observations of wave power at the lower-hybrid resonance. The observations and a whistler mode ray-tracing study suggest that multiple-hop lightning induced whistlers can be a source of hiss and plasma instabilities in the magnetosphere.

Irregular female migration to Europe is a growing phenomenon, as more and more women are fleeing their countries of origin due to gender inequality and violence. During the migration process, women experience physical, psychological and social problems that affect their sex lives. The aim of our study is to describe and understand how irregular migrant wom-en living in humanitarian reception centers experience their sexuality at different stages of the migration process. This qualitative phenomenological study collected data through a sixteen in-depth interviews with irregular migrant women between January and February 2023. Data anal-ysis was carried out using ATLAS-ti 23.0 software, from which three themes were extracted: 1) The sexual reality of sub-Saharan women, 2) In search of a better life: take the risk or surrender, and 3) The migrant sexual revolution. The sexual reality of sub-Saharan women is subject to a complex normative order. The migratory process has severe consequences on migrant women's sex life. The sexual needs of irregular migrant women admitted to humanitarian reception cen-ters undergo a process of change that must be understood by healthcare providers in order to make improvements to care provision.

This review summarizes the most recent developments of research on protozoan parasite infections ac-quired through food and drinking water and is aimed at gathering updated knowledge on the risk factors, illnesses caused, and measures for prevention. Reports included dated from 2019 to the present and regarded recent outbreaks and cases of severe infec-tions, prevalence in different population segments and food handlers, and occurrence in food and drinking water. Cryptosporidium spp., Entamoeba histolytica, Giardia intestinalis, Trypanosoma cruzi and Toxoplasma gondii were the microorganisms most frequently involved in large outbreaks and/or severe infections, while Cyclospora cayetanensis was most frequently involved in single case reports. Cystoisospora belli was implied in severe infections in immunocompromised patients, while Blastocystis homi-nis, Sarcocystis spp., Dientamoeba fragilis, Endolimax nana and Pentatrichomonas hominis appeared to be less relevant for number of symptomatic infections and pathogenic potential. A progressive improvement in surveillance of protozoan infections and infection sources was highlighted, especially in developed countries. The apparent increase in cases was concomitant with the implementa-tion of reporting systems and the application of molecular diagnostic methods that represent valuable in-struments for establishing epidemiological links and preventing or limiting outbreaks. The pathogenic role and sources of infection should be better elucidated for some species.

The novel Ionized Gas Thermoelectric Generator (IG-TEG) system that has been studied theoretically showing capabilities to continually extracting energy from the thermal energy of the ambient air, at low temperatures within the standard room temperature and below. This system does not need a temperature gradient in order to work, unlike the other TEGs that use Seebeck effect, and therefore this new system can be utilized for cooling purposes, by extracting energy instead of wasting energy in compressing the gas for cooling. This novel system was designed based on Static Ratchet Potential (SRP), which is known as a spatially asymmetric electric potential produced by an array of positive and negative electrodes. The ratchet potential produces electrical current from random Brownian Motion of charged particles that are driven by thermal energy. Ratchet potential was studied and investigated by several researches in the fields of sensing and energy harvesting. The main ratchet potential system parameter is the particles transportation, this parameter was studied under the condition of flashing ratchet potentials, and was analyzed based on several methods. In this study, a different approach is pursued to estimate particles transportation, by evaluating the charged particles distribution, and applying the other conditions of the SRP.

According to many researchers, Abstraction is the basis of mathematics, computing, counting devices, and computer science and engineering. What is more, all of the above deal with complexity management in some way, and abstraction is the most basic mechanism of complexity management.Generative software development - whether in the sense of empowering humans by machine to create software or in the sense of reusing products - has been and is one of the serious concerns and goals of software engineering. The interesting thing is that in both views of generativity, the main issue is still, in a way, complexity management: whether this complexity management is to achieve diversity and reuse management (Czarnecki’s approach) or to Structuring from existing structures (the approach of Alexander and his followers in an object-oriented society).In this article, we will first look at complexity and its various definitions. The definitions that show, despite the different perspectives on complexity in different disciplines and domains, all point in one direction. We will conclude that complexity is rooted in multiplicity. In the following, we will formally define complexity. In the following discussion, we will look at the generative patterns of software development, and then we will look at the complexity management patterns at seven levels.In this article, the author has tried to maintain a comprehensive approach to complexity and to consider the approaches of different domains to complexity.

Since the discovery of transposable elements (TEs) in Maize in the 1940s by Barbara McClintock [1] transposable elements have been described as junk, as selfish elements with no benefit to the host, and more recently as major determinants of genome structure and genome evolution. TEs are DNA sequences that are capable of moving to new sites in the genome and make additional copies while doing so. To limit the propagation of TEs, host silencing mechanisms are directed at transposon-encoded genes that are required for mobilization. The mutagenic properties of TEs, the potential of TEs to form new genes and affect gene expression, together with the host silencing mechanisms shape eukaryotic genomes and drive genome evolution. While TEs constitute more than half of the genome in many higher eukaryotes, transposable elements in the nematode C. ele-gans form a relatively small proportion of genome, about 15% [2]. Genetic studies of transposon silencing and the discovery of RNAi in C. elegans, propelled C. elegans to the forefront of studies of RNA-based mechanisms that silence TEs. Here, I will review the transposable elements that are present and active in the C. elegans genome, and the host defense mechanisms that silence these elements.

Eucalyptus, a therapeutic plant mentioned in the ancient Algerian pharmacopeia, specifically two species belonging to the Myrtaceae family - E. radiata and E. cinerea, were investigated in this study for their antibacterial, antioxidant, and anti-inflammatory properties. The study used aqueous extracts (AE) obtained from these plants, and the extraction yields were found to be dif-ferent. The in vitro antibacterial activity was evaluated using a disc diffusion assay against three typical bacterial strains. The results showed that E. radiata EAq was effective against all three strains, while E. cinerea EAq was only effective against E. coli. Both extracts displayed significant antioxidant activity compared to BHT. The anti-inflammatory impact was evaluated using a pro-tein (BSA) inhibition denaturation test. The E. radiata extract was found to inhibit inflammation by 75% at a concentration of 250 g/ml, significantly higher than the placebo. Ellagic acid, a pri-mary phytochemical found in the extracts, demonstrated noteworthy toxic and pharmacokinetic characteristics and a maximum binding energy of -7.53 kcal/mol for its anti-TyrRS activity in sili-co. The study suggests that the extracts and their primary phytochemicals could enhance the effi-cacy of antibiotics, antioxidants, and non-steroidal anti-inflammatory drugs (NSAIDs). As phar-maceutical engineering experts, we believe this research contributes to developing natural-based drugs with potential therapeutic benefits.

The freshwater snail genus Bulinus plays a vital role in transmitting parasites of the Schistosoma haematobium group. A hybrid schistosome between S. haematobium and S. mattheei has been recently detected using DNA-based identification methods in school children along the Lake Malawi shoreline in Mangochi District. This finding raised the need for contemporary revaluation of local interactions between schistosomes and snails, with a particular focus on snail species within the Bulinus africanus group. In 2017 and 2018, malacological surveys sampled several freshwater sites in Mangochi District. Collected snails (n= 250) were characterised using cytochrome oxidase subunit 1 gene (cox1), with DNA barcoding of the ‘Folmer’ region and a rapid PCR-RFLP typing assay with double digestion with HaeIII and SacI restriction enzymes. DNA cox1 sequence analysis, with phylogenetic tree construction, suggested the presence of at least three Bu. africanus group taxa in Lake Malawi, Bu. globosus, alongside first reports of Bu. africanus and Bu. angolensis, which can be differentiated by PCR-RFLP methods. In addition, A total of 30 of the 106 Bu. africanus group snails (28.30%) were positive to the Schistosoma-specific screen using real-time PCR methods. This study provides new insight into the recent changes in the epidemiology of urogenital schistosomiasis as likely driven by a new diversity of Bu. africanus group snails within the lake

Introduction: Transportation logistics play a pivotal role in facilitating both individual mobility and supply chain operations on a global scale. However, conventional transportation systems have contributed significantly to urban congestion and environmental degradation. In response to these challenges, there is a growing momentum towards the adoption of intelligent transportation systems (ITS) and sustainable transportation solutions. This research aims to explore the potential of renewable energy sources to power electric vehicles (EVs) and flying automobiles, thereby accelerating the transition towards a low-carbon future. Objectives: The primary objectives of this research are as follows: - Investigate the role of renewable fuels in powering both EVs and flying cars to reduce reliance on fossil fuels and mitigate carbon emissions. - Analyze the dynamic growth and sustainability implications of advancements in battery technology and alternative renewable energy sources, such as Hydrogen Fuel Cells. - Evaluate the challenges and opportunities associated with the integration of flying vehicles into existing transportation infrastructure, focusing on safety, airspace control, and infrastructure development. - Review insights and guidance to stakeholders on promoting sustainable transportation solutions for EVs and flying cars through the utilization of renewable energy sources and the reduction of carbon emissions from the literature. Methodology: This research employs a mixed-method approach, combining literature review, and causal loop diagram analysis. The literature review provides a comprehensive understanding of current trends, challenges, and opportunities in sustainable transportation and renewable energy technologies. A causal loop diagram is utilized to visualize the dynamic interactions between various factors influencing the adoption of EVs and flying cars, including technological advancements, policy interventions, and market dynamics. Results and Discussion: The findings of this research highlight the significant potential of renewable energy sources, such as solar, wind, and hydrogen, in powering both EVs and flying cars. Advances in battery technology and hydrogen fuel cells are identified as key drivers in accelerating the transition towards sustainable transportation systems. However, challenges remain in terms of infrastructure development, safety regulations, and airspace management for flying vehicles. Nevertheless, there is a noticeable advancement in reducing carbon emissions and reliance on fossil fuels with the widespread adoption of EVs. By harnessing renewable energy and implementing effective policy measures, stakeholders might able to promote the widespread adoption of sustainable transportation solutions, thereby contributing to environmental protection and societal well-being. Conclusion: Literally, this research underscores the importance of sustainable transportation solutions in addressing urban congestion, environmental pollution, and energy security concerns. By leveraging renewable energy sources and embracing technological advancements, such as EVs and flying cars, stakeholders pave the way for a more sustainable and resilient transportation system. However, concerted efforts are needed to overcome existing challenges and ensure the successful integration of these technologies into existing infrastructure. Through collaborative partnerships and innovative initiatives, a low-carbon future for transportation logistics can be achieved, benefiting both the environment and society as a whole.

Large-span post-tensioned (PT) beams play a crucial role in maximizing the benefits of post-tensioning techniques. Bonded and unbonded systems are prevalent, with the latter being more widespread in the United States. While bonded systems are advantageous for creating long spans when multiple tendons are grouped in ducts, limited literature exists on their demolition. In a case study, this paper addresses the unique challenge of demolishing large-span bonded post-tensioned beams due to a building's functional change. Emphasizing insights for engineers, it explores the use of cutting and dismantling methods, considering the presence of prestressed cables. The demolition process is distinctive due to the presence of numerous pre-stressed cables along the beams, necessitating a specialized and cautious cutting approach. This is accomplished through the use of a drilling technique that selectively distresses the tendons, ensuring they are not all affected simultaneously. An intriguing observation discussed in this paper pertains to the occurrence of horizontal cracks accompanied by loud sounds following the drilling process, offering insights from the design perspective of PT systems. The paper details an innovative method for safely demolishing large-span bonded PT beams, using ground-penetrating radar and computer models to navigate structural complexities and ensure nearby structures' safety.

Globalization, knowledge economy, information technology advancements, and the rise of learning societies contribute to the concept of a learning city. The study examines the economic indicators of Yazd city, Iran, in the context of learning city development. A descriptive-analytical approach with a survey method and cluster sampling was employed. Data analysis involved Kolmogorov-Smirnov normality test, single-sample T-test, simple linear regression, and Kendall's W test. The normality test confirmed data normality. The T-test indicated that experts perceived the current state of most variables in Yazd as undesirable. Regression analysis revealed a significant positive association between the economic index and independent variables. Kendall's W test prioritized areas based on economic indicators, with the top 7 and bottom 5 areas identified for focused interventions. The study emphasizes the need to prioritize areas within Yazd based on their economic indicators. This prioritization informs strategies for enhancing social and legal aspects of Yazd's transformation into a learning city. Further research should explore effective methods to cultivate a full-fledged learning environment in the city.

As with many of the non-deterministic search algorithms, particularly those are analogous to complex biological systems, there are a number of inherent difficulties, and the Bees Algorithm (BA) is no exception. Basic versions and variations of the BA have their own drawbacks. Some of these drawbacks are a large number of parameters to be set, lack of methodology for parameter setting and computational complexity. This paper describes a Grouped version of the Bees Algorithm (GBA) addressing these issues. Unlike its conventional version, in this algorithm bees are grouped to search different sites with different neighbourhood sizes rather than just discovering two types of sites, namely elite and selected. Following a description of the GBA, the results gained for 12 benchmark functions are presented and compared with those of the basic BA, enhanced BA, standard BA and modified BA to demonstrate the efficacy of the proposed algorithm. Compared to the conventional implementations of the BA, the proposed version requires setting of fewer parameters, while producing the optimum solutions much faster.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Conventional monitoring relies on "in vivo" (non-destructive) measurements of aboveground organ traits (such as stems, branches, and leaves) to analyze plantation growth trends and assess the effectiveness of management practices like watering and fertilization. This study reveals the necessity of “ex vivo” (destructive) approaches, post-excavation, to ensure fully reliable monitoring of plantation performance, including belowground organ growth and development trends. We showcase the effectiveness of dendrometric analysis, which measures the annual ring width in the secondary xylem (wood) of the taproot and stem. Monitoring above- and belowground organ growth trends allow for the exploration of similarities and differences in how different tree organs respond to internal and external factors. Such monitoring is especially crucial for assessing plantation performance in challenging climates, such as those found in arid and semi-arid lands.

COVID-19 is a severe global problem, and AI can play a significant role in preventing losses by monitoring and detecting infected persons in early-stage. This paper aims to propose a high-speed and accurate fully-automated method to detect COVID-19 from the patient's CT scan images. We introduce a new dataset that contains 48260 CT scan images from 282 normal persons and 15589 images from 95 patients with COVID-19 infections. At the first stage, this system runs our proposed image processing algorithm to discard those CT images that inside the lung is not properly visible in them. This action helps to reduce the processing time and false detections. At the next stage, we introduce a novel method for increasing the classification accuracy of convolutional networks. We implemented our method using the ResNet50V2 network and a modified feature pyramid network alongside our designed architecture for classifying the selected CT images into COVID-19 or normal with higher accuracy than other models. After running these two phases, the system determines the condition of the patient using a selected threshold. We are the first to evaluate our system in two different ways. In the single image classification stage, our model achieved 98.49% accuracy on more than 7996 test images. At the patient identification phase, the system correctly identified almost 234 of 245 patients with high speed. We also investigate the classified images with the Grad-CAM algorithm to indicate the area of infections in images and evaluate our model classification correctness.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

Abstract. The remarks by the Supreme Leader of the Islamic Revolution on the toll of the famines that afflicted occupied Iran in World War I and World War II indicate a desire to incorporate these calamities in Iran’s national narrative and collective memory. His criticism of famine historiography and stated toll numbers, and the unfolding catastrophic famine in Gaza, justify and necessitate a fresh look at each famine’s historiography and toll. This article re-estimates the toll of each famine by including many overlooked and neglected primary sources and in ways not previously done. It builds a trajectory of Iran’s demographic development from 1810 to 1944, and derives the toll of each famine. The World War II famine and typhus epidemics had claimed 5.5 million. World War I famine was also more deadly, though the 1869-73 famine was not far behind. At least 15.5 million Iranians died in the two world wars, a fact nowhere reflected in the history of the conflicts. Iran’s 1944 population of 12 million was unchanged from that of 1850 and a century of population growth obliterated

Through the half-unit circle area computation using the integration of the corresponding curve power series representation, we deduce a slow converging positive infinite series to $\pi$. However, by studying the remainder of that series we establish sufficiently close inequalities with equivalent lower and upper bound terms allowing us to estimate, more precisely, how the series approaches $\pi$. We use the obtained inequalities to compute up to four-digit denominator, what are in this sense, the best rational numbers that can replace $\pi$. It turns out that the well-known convergents of the continued fraction of $\pi$, $22/7$ and $355/113$ called, respectively, Yuel\"{u} and Mil\"{u} in China are the only ones found. Thus we apply a similar process to find rational estimations to $\pi+e$ where $e$ is taken as the power series of the exponential function evaluated at $1$. For rational numbers with denominators less than $2000$, the convergent $920/157$ of the continued fraction of $\pi+e$ turns out to be the only rational number of this type.

Under one-health perspective and the worldwide antimicrobial resistance concern, we investigate extraintestinal pathogenic Escherichia coli (ExPEC), uropathogenic E. coli (UPEC), and multidrug resistant (MDR) E. coli from 197 isolates recovered from healthy dogs in Spain between 2013 and 2017. Ninety-one (46.2%) isolates were classified as ExPEC and/or UPEC including 50 clones, among which (i) four clones were dominant (B2-CH14-180-ST127, B2-CH52-14-ST141, B2-CH103-9-ST372 and F-CH4-58-ST64815) and (ii) 15 had been shown to be displayed by previously published isolates causing extraintestinal infections in humans. Twenty-eight (14.2%) isolates were classified as MDR, associated with B1, D and E phylogroups and included 24 clones, of which eight had also been identified among human isolates causing infections. We selected 23 ST372 strains, 21 healthy dogs faecal isolates and two human clinical isolates for whole genome sequencing and built a SNP-tree with these 23 genomes and 174 genomes (128 from canine strains and 46 from human strains) obtained from public databases. The analysis of these 197 genomes allowed to identify six clusters. Cluster 1 comprised 74.6% of the strain genomes that were mostly composed of canine strain genomes (P < 0.00001). Clusters 4 and 6 also included canine strain genomes, while clusters 2, 3 and 5 were significantly associated with human strain genomes. All these findings suggest that dogs are reservoirs of ExPEC, UPEC and MDR E. coli isolates with zoonotic potential.

Duct-dependent lesions are classically divided into duct dependent pulmonary circulation which involves severe right sided obstructive lesions such as pulmonary atresia or critical stenosis, and duct dependent systemic circulation which is characterized by malformation of the left side of the heart, and whose severest spectrum is hypoplastic left heart syndrome. Dextro-transposition of the great arteries remains in gray zone between being included in some old classifications as a duct dependent pulmonary circulation lesion or a new category of duct-dependent or independent mixing lesion. We hypothesize that re-classifying duct dependent congenital defects into duct dependent perfusion and oxygenation offers a model to fit D-TGA into the same category of right sided obstructive lesions and reflects the clinical spectrum in a more comprehensive way.

The Eurasian grapevine (Vitis vinifera L.) is the most widely grown horticultural crop in the world and is important for the economy of many countries. In the wine production chain, grape varieties play an important role as they directly influence the authenticity and classification of the product. Identifying the different grape varieties is therefore fundamental for quality control and inspection activities, as well as for regulating production. Currently, ampelography and molecular analysis are the main approaches to identifying grape varieties. However, both methods have limitations. Ampelography is subjective and prone to errors and is experiencing enormous difficulties as ampelographers are increasingly scarce. On the other hand, molecular analyses are very demanding in terms of cost and time. In this scenario, Deep Learning (DL) and Machine Learning (ML) methods have emerged as a classification alternative to deal with the scarcity of ampelographs and avoid molecular analyses. In this study, the most recent and current methods for identifying grapevine varieties using DL classification-based approaches are presented through a systematic literature review. The classification pipeline of the 31 studies found in the literature was described, highlighting its pros and cons. Most of the studies used DL-based models trained with leaf images acquired in a controlled environment at a maximum distance of 1.2 metres to classify grape varieties. In addition, there is a large gap between practical applications and the datasets used: a great lack of varieties, limited data acquired in the field and a lack of tests on plants under adverse conditions. Potential directions for improving this area of research were also presented.

Educational institutions must identify students who are academically struggling to provide them with necessary support to improve their performance. In this context, recommendation systems powered by deep learning techniques are vital for detecting and categorizing such students. These systems help students plan their future by uncovering patterns in their historical academic data. This study introduces a new deep learning model designed to classify academically underperforming students in educational settings. The model incorporates a Gated Recurrent Neural Network (GRU) and includes specific neural network features like a dense layer, max-pooling layer, and the ADAM optimization algorithm. The model's training and evaluation were conducted using a dataset comprising 15,165 student assessment records from various academic institutions. The performance of the developed GRU model was benchmarked against other educational recommendation systems, including Recurrent Neural Network models, AdaBoost, and the Artificial Immune Recognition System v2. The proposed GRU model demonstrated remarkable accuracy, achieving an overall rate of 99.70%.

Considering the significant advancements in autonomous vehicle technology, research in this field is of interest to researchers. To automatic parking, controlling steer angle, gas hatch, and brakes need to be learned. Due to the increase in the number of cars and road traffic, car parking space has decreased. Its main reason is information error. Because the driver does not receive the necessary information or receives it too late, he cannot take appropriate action against it. This paper uses two phases: the first phase, for goal coordination, was used genetic algorithms and the Cuckoo search algorithm was used to increase driver information from the surroundings. Using the Cuckoo search algorithm and considering the limitations, it increases the driver’s level of information from the environment. Also, by exchanging information through the application, it enables the information to reach the driver much more quickly and the driver reacts appropriately at the right time. The suggested protocol is called the MODM-based solution. Here, the technique is assessed through extensive simulations performed in the NS-3 environment. Based on the simulation outcomes, it is indicated that the parking system performance metrics are enhanced based on the detection rate, false-negative rate, and false-positive rate.

Nowadays, one of the biggest concern of human being is greenhouse gas emission, especially carbon dioxide emission in developed and under-developing countries. In this study, connectionist models including LSSVM (Least Square Support Vector Machine) and evolutionary methods are employed for predicting the amount of CO₂ emission in six Latin American countries, i.e., Brazil, Mexico, Argentina, Peru, Chile, Venezuela, and Uruguay. The studied region is modelled based on the available input data in terms of Million tons including oil (Million tons), gas (Million tons oil equivalent), coal (Million tons oil equivalent), $R_{ew}$ (Million tons oil equivalent), and Gross Domestic Product (GDP) in terms of billion US dollars.} Moreover, the available patents in the fields of climate change mitigation in six Latin American countries namely Brazil, Mexico, Argentina, Peru, Chile, Venezuela, and Uruguay has been reviewed and analyzed. The results show that except Venezuela, all other mentioned countries have invested in renewable energy R&D activities. Brazil and Argentina have the highest share of renewable energies which account for 60% and 72% respectively.

In this work, some numerical radius inequalities based on the recent Dragomir extension of Furuta's inequality are obtained. Some particular cases are also provided.

Woodland strawberry (Fragaria vesca L.) is an underutilized plant species, appreciated by consumers for its qualitative features. Utilizing technical means of production, such as plant biostimulants, that can increase crop productivity and quality could be highly important in woodland strawberry cultivation. The scope of the present study was to appraise the influence of two biostimulants (Trichoderma atroviride and plant protein hydrolysate) - used either alone or combined - on plant performance and economic profitability of two woodland strawberry genotypes (‘Alpine’ and ‘Regina delle Valli’). Overall, data showed that ‘Alpine’ had the highest productive performances, whereas ‘Regina delle Valli’ revealed the highest fruit qualitative traits. T. atroviride inoculation and V-PH application significantly boosted plant marketable yield (+20.5% for T. atroviride and +12.9% for V-PH), total sugars (+1.9% for Trichoderma and +1.4% for V-PH) and anthocyanins (+14.1% for T. atroviride and +9.8% for V-PH) compared to non-treated plants. Plants supplied with both biostimulants had higher marketable yield (+34.8%), mean fruit weight (+6.0%), fruit dry matter (+13.8%), total sugars (+3.5%), ascorbic acid (+12.7%), flavonoid (+26.3%) and anthocyanins (+29.9%) compared to non-treated plants. Furthermore, our study revealed that the highest fruit polyphenols concentration was recorded in both genotypes treated with the combination of biostimulants and in ‘Regina delle Valli’ sprayed with V-PH, whereas the highest antioxidant activity was found in ‘Regina delle Valli’ fruit when plants were supplied with both biostimulants. Our study pointed out that the application of microbial and non-microbial biostimulants, especially in combination, might be an useful strategy for improving performances of underutilized species and, therefore, encourage its cultivation, valorisation and economic profitability (+10195.3 €/ha when plants were exposed to both biostimulants).

Gastric cancer is a challenging public health concern worldwide and remains a leading cause of cancer-related mortality. The primary risk factor implicated in gastric cancer development is infection with Helicobacter pylori. H. pylori induces chronic inflammation affecting the gastric epithelium, which can lead to DNA damage and promotion of precancerous lesions. Disease manifestations associated with H. pylori are attributed to virulence factors with multiple activities and its capacity to subvert host immunity. One of the most significant H. pylori virulence determinants is the cagPAI gene cluster, which encodes a type IV secretion system and the CagA toxin. This secretion system allows H. pylori to inject the CagA oncoprotein into host cells, causing multiple cellular perturbations. Despite the high prevalence of H. pylori infection, only a small percentage of affected individuals develop significant clinical outcomes, while most remain asymptomatic. Therefore, understanding how H. pylori triggers carcinogenesis and its immune evasion mechanisms is critical in preventing gastric cancer and miti-gating the burden of this life-threatening disease. This review aims to provide an overview of our current under-standing of H. pylori infection, its association with gastric cancer and other gastric diseases, and how it subverts the host immune system to establish persistent infection.

Paratuberculosis, or Johne's disease, caused by Mycobacterium avium subsp. paratuberculosis (MAP), is a chronic granulomatous enteritis affecting both domestic and wild ruminants. The agent was also found in wild mammals such as wild boar (Sus scrofa), however, the role of wild mammals in the epidemiology of MAP is unclear. During the research period, 941 free-ranging wild boar (S. scrofa) legally hunted in two locations in the Centre-eastern region of Portugal were examined. Ninety-seven wild boar exhibited one or more gross lesions and were tested for the presence of Mycobacterium avium subsp. paratuberculosis using acid-fast staining, mycobacterial culture, poly-merase chain reaction (PCR), and histopathological examination. Forty-five animals (46.4%, 95% CI: 36.5-56.3%) were identified as infected, as indicated by positive results in culture and/or PCR. The findings revealed that the most significant risk factor was being a juvenile compared to year-lings and adults (OR = 10.2, 95% CI: 2.2-48.0). Based on our results, 37.9% (n = 11) of the infected animals were considered suitable for human consumption. Our findings offer novel insights into mycobacterial infections in wild boar populations in Portugal and suggest that wild boar could be a source of human infection if zoonotic potential is considered.

Condition monitoring is a primary principle for predictive maintenance. In this regard, several techniques have been employed, each of which has its strengths and weaknesses. In this work, the relationships between the electrical (ε', ε", tan δ) and chemical (Fe, Pb, Cu, Cr, Al, Si, Zn) properties of engine lubricants were investigated using soft computing models. The models' performance was evaluated considering some criteria, including RMSE and MAPE. The RBF model was determined as the best one to predict chemical properties (Fe, Pb, Cu, Cr, Al, Si, Zn) through electrical indexes (ε', ε", tan δ). The RBF’s parameters (e.g., hidden size and training algorithm) were then optimized for optimum performance. For instance, in the RBF model implemented to predict Al, the best hidden size and training algorithmic were 15 and 'trainlm', respectively. Finally, by sensitivity analysis it was observed that eliminating any of the inputs does not improve the performance of the RBF model performance. In general, the results of the current research showed that the electrical properties (e.g., ε', ε", tan δ) have the capability of estimating the contaminants in the lubricants which can improve the existing monitoring methods.

background: The Islamic Republic of Iran has been under sanctions since 1979. These sanctions were further reinforced between the years 2005 and 2012. This study utilizes available data from Iran post-sanctions to review the impact of economic sanctions on both the mental health and the quality of life of Iranian citizens.Methods: A comprehensive scoping review was conducted to identify studies examining the impact of sanctions on health in Iran. Searches were initiated in 2012 using PubMed/Medline, Embase, Web of Science, Scopus, and the Scientific Information Database (Iranian Database) with keywords such as sanctions, implications, mental health, quality of life, civilian mental health, and Iran. Subsequent to the screening process, secondary reports and letters to the editor were excluded. Only original studies—those collecting data via observation, interviews, surveys, experiments, or literature reviews—were retained for analysis. In addition to these search strategies, reference scanning was undertaken to identify additional articles pertinent to the scope of the current study. This thorough approach facilitated the discovery of relevant and significant articles exploring the effects of sanctions against Iran on the mental health and overall well-being of its civilian population. Following the search, duplicate articles were meticulously identified and removed by the authors. Data were subsequently extracted and summarized, focusing on study characteristics and the observed effects of sanctions on civilian mental health and quality of life in Iran.Result: Out of 165 items identified in the preliminary search, ten articles met the inclusion criteria. These selected articles highlighted the pronounced effects of sanctions on various health-related domains.Conclusion: Since 2012, Iran has been subject to intensified sanctions. There is evidence to suggest that the economic sanctions, imposed by Western nations, and have exerted a negative and detrimental impact on the health of individual Iranians.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Nanotechnology has become a popular topic in agricultural and animal research, generating sig-nificant global interest. Nanoparticles (NPs)-enabled agriculture and animal husbandry (AHs) products have three main principles: crop production, protection, and nutrient enrichment. Re-search on this topic has grown exponentially in recent years, with an increasing number of peer-reviewed literature and patents on NPs-enabled agriculture and AH products. This study examines and collects data on the various applications of NPs-enabled agricultural products for crop production, protection, and livestock improvement from the core nanotechnological database. The search returned several types of NPs and products used in agriculture and AH, countries that utilize these products at a commercial level, and analysis of these data by phyton, R-statistical software. Our findings show remarkable growth of nanotechnology in agriculture, AH, and re-search fields for future sustainability goals in the era of climate change

The criteria of “Distinctness, Uniformity and Stability” as well as a high "overall quality index” are used to register the Italian modern varieties to the national register. Differently, local conservation varieties can be certified under different EU Directives having, as overall objective, the preservation of biodiversity and the containment of genetic erosion. In recent years, products derived from an-cient grains are perceived to be healthier and more sustainable by consumer, especially in Italy, with consequent higher market prices. Ancient tetraploid wheat varieties registered in the national reg-ister of conservation varieties are 28, 24 of which are Sicilian. They are supposed to have a wide genetic variability compared to modern ones, making them vulnerable of fraud because they are difficult to trace. It is therefore important to have tools able to discriminate the autochthonous Si-cilian varieties. This can be done by gluten proteins composition, which also gives information on the technological properties of derived products. Fifty-one accessions belonging to 22 ancient va-rieties of Sicilian tetraploid (mostly durum) wheat were analyzed. Although a wide intra-accession and intra-varietal variability was assessed, the gliadin pattern of bulks of seeds belonging to each variety was discriminatory. Moreover, differences in technological attitudes were found between landraces. This paves the way to use gluten protein patterns for traceability allowing local farmers and producers to valorize their products and assure consumers about the transparency of the entire supply chain.

Isoamyl (E)-3-(3,4-dimethoxyphenyl)acrylate (1) was obtained 95% yield by 2-methyl-6-nitrobenzoic anhydride (MNBA)/4-dimethylaminopyridine (DMAP)-catalyzed reaction at room temperature for 190 minutes in dichloromethane. The structure of isoamyl (E)-3-(3,4-dimethoxyphenyl)acrylate (1) was established by NMR, FTIR, and the high resolution of mass spectroscopies. In vitro sun protection factor evaluation exhibited value of 37.10 ± 0.03 which indicates that isoamyl (E)-3-(3,4-dimethoxyphenyl)acrylate (1) as a sunscreen agent with high protection.