This paper focused on impact localization of composite structures, which possess more complexity in the guided wave propagation because of the anisotropic behavior of composite materials. In this work, a composite plate was manufactured by using a compression molding process with proper pressure and temperature cycle. Eight layers of woven composite prepreg were used to manufacture the composite plate. A structural health monitoring (SHM) technique is implemented with piezoelectric wafer active sensors (PWAS) to detect and localize the impact on the plate. There are two types of impact event are considered in this paper (a) low energy impact event (b) high energy impact event. Two clusters of sensors recorded the guided acoustic waves generated from the impact. The acoustic signals are then analyzed using a wavelet transform based time-frequency analysis. The proposed SHM technique successfully detect and localize the impact event on the plate. The experimentally measured impact locations are compared with the actual impact locations. An immersion ultrasonic scanning method was used to visualize the composite plate before and after the impact event. A high frequency 10 MHz 1-inch focused transducer was used to scan the plate in the immersion tank. Scanning results show that there is no visible manufacturing damage in the composite plate. However, clear impact damage was observed after the high-energy impact event.

Copper indium gallium selenide (CIGS) is an inexpensive material that has the potential to dominate the next-generation photovoltaic (PV) industry. Here we detail computational investigation of CIGS solar cell with encouragement of adopting cuprous dioxide (Cu₂O) as a Hole Transport Layer (HTL) for efficient fabricated CIGS solar cells. Although Cu₂O as a HTL has been studied earlier for perovskite and other organic/inorganic solar cell yet no study has been detailed on potential application of Cu₂O for CIGS solar cells. With the proposed architecture, recombination losses are fairly reduced at the back contact and contribute to enhanced photo-current generation. With the introduction of Cu₂O, the overall cell efficiency is increased to 26.63%. The wide-band of Cu₂O pulls holes from the CIGS absorber which allows smoother extraction of holes with experiencing lesser resistance. Further, it was also inferred that, HTL also improves the quantum efficiency (QE) for photons with large wavelengths thus increases the cell operating spectrum.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

This study investigates the impact of Government Consumption (GC) on Saudi Arabia’s GDP during major economic crises from 1969 to 2022, with a focus on periods marked by fluctuations in oil and non-oil revenues. By integrating these revenue streams, the research provides a more comprehensive analysis of fiscal policy effectiveness during economic downturns. Using an Autoregressive Distributed Lag (ARDL) model, the study reveals the complex role of Government Consumption (GC) in stabilizing and stimulating the Saudi economy amidst revenue volatility.Key findings indicate that while GC does not significantly influence GDP in the short term, its long-term effectiveness varies across different crises. Specifically, GC has acted as a buffer against immediate economic shocks during certain crises while providing a stimulus for economic recovery in others. For instance, during the 2020 COVID-19 pandemic, timely fiscal measures significantly boosted GDP, underscoring the importance of adaptive and proactive fiscal policies. Conversely, the 2014-2016 oil price collapse demonstrated that GC alone was insufficient to counteract economic downturns, emphasizing the need for diversified revenue strategies.These findings underscore the dual role of GC in economic stabilization and recovery. During the COVID-19 pandemic, GC played a crucial role in both mitigating negative economic impacts and supporting recovery efforts, showcasing its effectiveness in times of global disruptions. This demonstrates GC's capability as an immediate buffer against economic shocks and a stimulus for economic recovery. In contrast, during the 2014-2016 oil price collapse, GC was less effective, indicating the limitations of relying solely on government spending without broader economic diversification. This highlights the necessity of diversified revenue strategies to complement fiscal measures for long-term economic resilience.The robustness of the findings was ensured through various diagnostic tests, including checks for autocorrelation, heteroskedasticity, and stationarity of residuals. The absence of significant autocorrelation and heteroskedasticity, along with the stationarity of differenced variables, confirms the validity of the econometric models used.The study contributes to the discourse on fiscal policy in oil-dependent economies by illustrating the critical role of diversified revenue strategies and adaptive fiscal measures in enhancing economic resilience. Recommendations are offered for policymakers to optimize fiscal strategies, ensuring robust economic recovery and long-term stability in volatile markets. This research highlights the necessity for Saudi Arabia to refine its fiscal policies towards greater economic diversification and stability.

Leptospirosis is a zoonotic disease of global importance. The current killed vaccine provides serovar-specific protection without sterilizing immunity. Several surface antigens, including Leptospira immunoglobulin-like proteins (LigA and LigB), have been identified as subunit vaccine candidates; however, they require potent adjuvants. Bacterial Lipopolysaccharide (LPS), including lipid A, is a well-known immunostimulatory agent, and the formulation of Monophosphoryl Lipid A (MPLA) in Alum is a clinical adjuvant. Being less endotoxic, we tested the adjuvant activity of lipid A purified from L. interrogans serovar Pomona (PLA) for its ability to activate innate and enhance antigen-specific adaptive immune response. PLA-induced activation of macrophages similar to levels induced by MPLA, albeit at a much higher dose, indicating that it is less stimulatory than MPLA. Mice immunized with a Variable portion of LigA (LAV) formulated in Alum and PLA (LAV-Alum-PLA) induced significantly higher levels of LAV-specific humoral and cellular immune response than Alum but similar to levels induced by Alum-MPLA. The adjuvant activity of PLA seems to be quite similar to MPLA and primarily mediated through enhanced recruitment, activation, and uptake of antigens by innate immune cells. Moreover, like MPLA, the PLA formulation was able to generate a long-term memory response. Most importantly, PLA demonstrated better potency than MPLA formulation and generated sterilizing immunity against challenge in a hamster model of leptospirosis. Altogether, our study has provided important insight into the adjuvant activity of Leptospira lipid A and has opened avenues for the development of LPS-based vaccines against this dreadful zoonosis.

Pakistan relies mostly on fossil fuel for fulfilling its energy demand which is expensive as 11 well as not friendly for the environment. The need of the hour is to shift from fossil fuels to renew-12 able energy resources like geothermal, wind, solar etc. to cater for global warming issues. Pakistan 13 has a lot of potential geothermal sites because of several fault lines and hot springs. A sound 14 knowledge of ground temperature is essential to use geothermal energy, which is obtained by drill-15 ing boreholes and putting sensors making it an expensive procedure. Thus, to avoid huge cost for 16 drilling bore holes, particularly for ground temperature analysis, a numerical approach has been 17 considered for determining ground temperature. Furthermore, correlation charts between air and 18 ground temperatures have been developed as there were no proper studies on the ground temper-19 ature of Pakistan. Then, with the help of a boreholes drilled in National University of Sciences and 20 Technology Islamabad Pakistan, the actual ground and numerically calculated temperatures have 21 been compared which shows an error margin in the range between 0.27% for higher depths to 7.3% 22 near surface. Thus, it is shown that the proposed method is easy to implement and better than large 23 scale testing methods for the depths at which geothermal energy is extracted.

Herein we foremost detailed the numerical modeling of the double absorber layer- methyl ammonium lead iodide– carbon nitride layer solar cell and subsequently provided in-depth insight on the active layer associated with dominant radiative and non-radiative recombination losses limiting the efficiency ( ) of the solar cell. Under recombination kinetics phenomena, we explored the influence of Radiative recombination, Auger recombination, Shockley Read Hall recombination, the energy distribution of defects; Band Tail recombination (Hoping Model), Gaussian distribution, metastable defect states including single donor (0/+), single acceptor (-/0), Double Donor (0/+/2+), double acceptor (2/-/0-), and the interface layer defects on the output characteristics of the solar cell. Setting defect (or trap) density to with uniform energy distribution of defects for all the layers, we achieved the of 24. 16 %. A considerable enhancement in power conversion efficiency was perceived as we reduced the trap density to for the absorber layers. Further, it was observed that for the absorber layer with double donor defect states, the active layer should be carefully synthesized to reduce crystal order defects to keep the total defect density as low as to achieve efficient device characteristics

We report the growth of graphene at a low temperature using the cold wall chemical vapor deposition technique (CWCVD). Few layered (~6-8 layers) graphene were grown on nickel-coated silicon with acetylene as the precursor gas. The advantage of the combination of the acetylene (as a carbon feedstock) and the nickel catalyst was the lowering of the graphene growth temperature. Nickel coated silicon samples were pre-treated (heat treatment in inert atmosphere) before the growth and the effect of the pre-treatment on the catalyst as well as on the grown film was studied. The final samples were characterized with scanning electron microscopy and Raman spectroscopy. In CWCVD route, the heating of only the substrate holder enabled high heating and cooling rates, which, along with the control over partial pressure of the precursor gas had profound effect on the formation of graphene. In the best sample we have achieved almost equal intensity of the G and 2D peaks in Raman spectrum, which implied about ~6-8 layers of Graphene. The defect peak (the D band) was extremely small in the sample and it was attributed to the ripples and the underlying roughness of the nickel film. We analyzed that a proper choice of the thickness of catalyst layer and a higher cooling rate after graphene growth it would be possible to obtain monolayered graphene. Similar samples grown in a normal atmospheric CVD (with some engineered design to promote fast cooling) were also compared with the cold wall CVD grown samples and plasma assisted CWCVD, and cold-wall CVD demonstrated a better control over the quality of graphene film through the fast cooling and a controlled partial pressure of the precursor gas.

Voltage Stability & Control, is very crucial compared to other Power System (PS) Quality and Stability issues. Long-Vertical-Power-Flows in Conventional Grids, causes voltage drops which in turn causes huge power losses, especially in the Medium Voltage (MV) and Low Voltage (LV) Distribution Networks. Such technical losses in abysmally-planned weak distribution networks, lead to substantial loss of revenues to the utility grid. Apart from classic Voltage Regulation (VR) techniques, with the rise of Distributed Generation (DG) based on Renewable Energy Sources (RES), Horizontal-Power-Flows can be introduced in the network, through various Smart Grid techniques. Coupling such sources, near load centers shall mitigate long flows from expensive conventional sources at times of huge demands, improving feeders’ Voltage Profile. This Ancillary Service of Voltage Support from DG RESs shall thereby alleviate revenue losses caused by long-power-flows in weak distribution grids. For a developing country like Pakistan, loss of revenue from an already expensive utility gives huge blow to the economy. So, a similar technique for voltage support is proposed for an 11-kV feeder, which faces similar problem, and the results are remarkable. The technique is implemented using OpenDSS Tool by modelling 3MWp PV Penetration along with some future storage.

Over the years, the need for autonomous systems such as drones, also known as unmanned aerial vehicles (UAVs), has significantly increased in popularity across several industries, including the military. The Internet of Battlefield Things (IoBT) represents a modern technological advancement that significantly enhances the operational efficacy of defense systems. It establishes an integrated military force by connecting individuals to intelligent technology in drones, radios, equipment, antennas and ground stations. This is achieved through the utilization of cloud and edge computing, sensors, mobile devices, embedded systems, and IoT-based systems. However, IoBT security is significantly compromised by enemies that exploit the vulnerabilities and malicious intrusions that specifically target the external environment or to obtain sensitive data. In addition, a comprehensive understanding of cyberattacks and countermeasures is essential for assuring the security of IoBT. On the other hand, as cyber threats get more complicated, trust becomes increasingly important for the security of digital systems. Within this context, the zero trust architecture contends that the security of a complex network is inherently vulnerable to internal and external threats. In defense, UAV security system applications, for example, the primary purpose of the zero trust architecture is to limit the vulnerability of military UAV systems to cyberattacks, hence reducing the possibility of data breaches and illegal entry. This study conducts a systematic review aimed at identifying different aspects of cybersecurity strategies for protecting UAV systems within the IoBT domain. Furthermore, zero trust architecture is presented in the study as an effective prospective solution to the security issues that develop in defense UAV systems.

Leukemia represents as one of the most common primary malignancies of the hematologic system in both children’s and adults and remains a largely incurable or relapse disease. The elucidation of disease subtypes based on mutational profiling, has not improved clinical outcomes. IDH1/2 are key enzymes of TCA cycle that produces α-ketoglutarate (αKG), however their mutated version, are well reported in various cancer types including leukemia, produces D-2 hydroxyglutarate (D-2HG), an oncometabolite. Recently, some studies have shown that wild type IDH1 is highly expressed in non-small cell lung carcinoma (NSCLC), primary glioblastomas (GBM) and several hematological malignancies and corelates with disease progression. In this work, we have showed treatment of wild type IDH1 leukemia cells with specific IDH1 inhibitor switched leukemic cells towards gly-colysis from oxidative phosphorylation (OXPHOS) phenotype. We also noticed reduction in αKG in treated cells possible suggesting inhibition of IDH1 enzymatic activity. Further, we found that IDH1 inhibition reduces the metabolites related to one carbon metabolism, essential to maintain global methylation in leukemic cells. Finally, we observed that metabolic alteration in IDH1 inhibitor treated leukemic cells promotes reactive oxygen species (ROS) formation along with loss of mito-chondrial membrane potential, leading towards apoptosis in leukemic cells. Overall, we showed that wild type IDH1 targeting in leukemic cells promote metabolic alterations that can be exploited for combination therapies for better outcome.

In 2020, students of Pakistan had to adapt to the online environment for the very first time. This study aims to analyze the perceptions of medical, dental, and allied health students about online education in Pakistan. A descriptive, cross-sectional study was done to assess the level of acceptance of undergraduate students. A pre-validated questionnaire regarding demographics, past-experience of e-learning, advantages disadvantages of e-learning, and general perception of students towards e-learning was distributed. Descriptive statistics were computed for demographics, Mann-Witney-U test was used to compare the differences of perceptions between pre-clinical year and clinical years students. Kruskal-Wallis test was applied to compare the results of three specialties of students. Chi-square was used to compare overall category-wise positive and negative responses of students. 1200 students participated in the study. The major advantage identified by all students was the ‘comfortable environment’ in which they studied online. The major disadvantage selected by preclinical year students was ‘anxiety due to social isolation’ and that chosen by clinical year students was ‘lack of patient interaction’. Overall, 72% of students had a negative perception of e-learning. Student-teacher training, student counselling sessions, and innovative techniques need to be introduced to enhance student engagement and reduce pandemic stress.

Introduction: Mucopolysaccharidosis type I (MPSI) is an autosomal recessive lysosomal storage disorder characterized by deficient or absent α-L-iduronidase (IDUA) enzyme activity due to pathogenic variants in IDUA gene. Early treatment with hematopoietic stem cell transplantation and/or enzyme replacement therapy is associated with improved outcomes in this progressive multisystem disease. The diagnosis is usually delayed due to late presentation and nonspecific symptoms resulting in high morbidity and mortality. The incidence of MPSI in US is estimated to be 0.26:100,000, however, it is unknown in Kuwait. This pilot study was undertaken to screen MPSI in all Kuwaiti neonates born at Farwaniya Hospital over a period of 12-months. This study examined the incidence of MPSI in a major center in Kuwait for inclusion in the national newborn screening program to enable its early detection and adequate treatment. Methods: All Kuwaiti neonates born at Farwaniya Hospital, Kuwait from December 2021 to December 2022, were screened for MPSI. The screening consisted of determining IDUA enzyme activity in dried blood spots (DBS)-derived samples by Tandem Mass Spectrometry. A follow-up genetic analysis of IDUA gene is planned to screen the cases with diminished IDUA enzyme activity as second-tier testing. Results: A total of 618 newborns, including 331 (54%) males and 287 (46%) females, were screened. Twenty of them had deficient IDUA enzyme activity but showed negative genetic testing for IDUA. However, we have diagnosed one additional female baby with MPSI, who belonged to Farwaniya Hospital, but the parents chose to deliver in a private hospital. She presented at age three months with recurrent upper airway infections, snoring and extensive Mongolian spots. The molecular study revealed previously reported pathogenic nonsense variant in IDUA c.1882C>T; p.(Arg628Ter), associated with severe phenotype. That being included, MPSI is estimated to be about 0.3% among tested females and 0.2% of all screened cases in Kuwait. Conclusion: Our study is the first to evaluate the incidence of MPSI in Kuwait. Given the single center, small number of screened babies and the short study duration thus far, it is premature to calculate the incidence of MPSI. It is anticipated that as the study continues and more infants are examined, we would be able to estimate the incidence of this disease in our population correctly. Further studies including screening newborns in all maternity hospitals in Kuwait are needed to calculate the actual incidence of MPSI. Our data supports including MPSI in national newborn screening program to allow early initiation of treatment and thus improve disease outcome.

Traumatic brain injury (TBI) is among the leading causes of mortality and long-term impairment globally. TBI has a dynamic pathology encompassing a variety of metabolic and molecular events that occur in two phases, primary and secondary. An external forceful blow to the brain initiates the primary phase, which is followed by a secondary phase that involves the release of calcium ions (Ca2+) and the initiation of a cascade of inflammatory processes, including mitochondrial dysfunction, rise in oxidative stress, activation of glial cells, and damage to the blood-brain barrier (BBB), resulting in paracellular leakage. There is currently no FDA-approved drug for TBI, but existing approaches rely on delivering small and macromolecular treatments, which are severely constrained by the BBB, poor retention, off-target toxicity, and complex pathology of TBI. Therefore, there is a demand for innovative and alternative therapeutics with effective delivery tactics for diagnosis and treatment of TBI. Tissue engineering and use of biomaterials is one such alternative approach. With this approach, neuronal stem cell therapy is combined with synthetically generated tissue materials such as hydrogels, self-assembling peptides, and electrospun nanofibers, which may induce neurite outgrowth, differentiation of human neural stem cells, and nerve gap bridging in TBI. This review examines tissue engineering and the use of biomaterials as potential treatments for TBI, including their synthesis, mechanisms of action, and limitations. The review also discusses challenges facing tissue engineering and biomaterial technology including survival rate of transplanted stem cells and the development of biodegradable, biocompatible, and mechanically flexible biomaterials. A better understanding of the mechanisms and drawbacks of these novel therapeutic approaches will help guide the design of future TBI therapies.

In the realm of smart manufacturing, equipment plays a pivotal role, impacting the efficiency and quality of production. Ensuring equipment availability and optimal performance is crucial, necessitating effective maintenance strategies. This paper addresses the complexities of smart device maintenance, which often involves collaboration between multiple entities like device owners, manufacturers, suppliers, and external maintenance services. To enhance this cooperative maintenance, we propose a novel maintenance system based on permissioned blockchain technology, offering superior security and reliability compared to conventional cloud-based platforms. Our contributions include developing an integrated maintenance system framework for smart manufacturing, which facilitates interactions among diverse stakeholders. Additionally, we have developed a prototype of this maintenance system, serving as a practical model for real-world application. Our research primarily demonstrates the practicality and advantages of using permissioned blockchain for maintenance systems in the manufacturing sector, paving the way for more secure, efficient, and collaborative maintenance practices.

Due to the rapid growth of the Internet of Things (IoT), securing communications between a huge number of devices has become very difficult. Access controls and authentication secure the connection between IoT devices and protect sensitive data from unauthorized users or malicious attackers. In this paper, we provide a comprehensive review to emphasize the critical role of authentication and access control in securing IoT environments. This paper explores different types of access controls, like Attribute-Based Access Control and Role-Based Access Control. Furthermore, it demonstrates different authentication techniques, like passwords and biometrics. Based on the previous mechanisms, we discuss different IoT security challenges regarding authentication and access control mechanisms and highlight future directions. In addition, this paper investigates the integration between access control and authentication to safeguard IoT communications.

Background: The psychomotor agitation of the behavioural and psychological symptoms of dementia (BPSD) is one of the common issues in aged care facilities, leading to the poor functional and medical consequences. Psychotropic interventions are the preferred choice of treatment, but which medication should be the prescribers first preference? This review aims to compare pharmacological interventions for psychomotor agitation, judging them according to their effectuality and justifiability profiles. This is to be achieved by retrieving information from Randomised Control Trials (RCTs) and systematic reviews. Objectives: This review evaluates evidence from RCTs, systematic reviews, and meta-analyses of BPSD patients who have taken agitation treatments. Assessing the efficacy of selective serotonin reuptake inhibitors (SSRI) and antipsychotic treatments when compared to each other for the purpose of improving agitation outcomes. Methods: This review includes RCT that compared one or more active ingredient medications with another medication or with a placebo, along with systematic reviews comparing citalopram (SSRI) with antipsychotics such as quetiapine, olanzapine, and risperidone. Studies were extracted by searching and accessing databases, such as PubMed, OVID, and Cochrane with restrictions of date from 2000 to 2021 and English language. Conclusion: There is still limited studies of SSRIs for the treatment of agitation in BPSD. SSRIs such as citalopram were associated with a reduction in symptoms of agitation, and lower risk of adverse effects compared to antipsychotics. Future studies are required to assess the long-term safety and efficacy of SSRI treatments for agitation in BPSD.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

Today’s urban spaces face precipitous challenges and complications, which include the COVID-19 pandemic, urbanization, population growth, and climate change. Proximity plays an essential role in influencing the integrity of public spaces and urban environments, while proxemics studies people’s experience, and the benefits, of urban space, and is based on a behavioral system of activities that includes ‘territoriality’. There is a need to study the behavioural patterns of people in given situations with proxemic dimensions in order to sustain both human beings and the quality of urban space. However, people behave spontaneously within environmental settings and reflect each other’s responses, meaning it is important to distinguish between different cultures, which tend to respond in particular ways to the meaning of proximity. This suggests there is no universal indicator for phenomena such as crowding. The aim of this paper is to highlight the interrelationship between urban form and urban life. This study focuses on two patterns of activity - street life and social life - by adopting a descriptive-analytical approach to documentary and desk research. The findings reveal a vital distinction between social and public patterns of proximity, while other proximities, although critical, are not observed within interactions between people.

In an urban context, the street network can be considered the most substantial element, as its role is to create the whole urban setting. The street network is a spatial pattern that can be recognized as a linkage bonding other components of the urban context, such as buildings and open spaces. Basically, the street is not only a collection of lines that transfer people, vehicles and goods but also denote a broad range of activities and influences people’s responses. In this respect, some studies address the street as a network that entails two key elements, link and node; the link can be defined by the type of mechanism that it connects, while the node can be identified according to the analysis technique. Defining the street’s elements is a crucial step in ascertaining the expression of whatever is a link or/and a node. Thus, some scholars use the link to refer to a street, and node for the intersection, while others employ the opposite meaning. Two different viewpoints deal with spatial network analysis; the first is a technique based on topological depth, such as Space Syntax SS, and the second is Multiple Centrality Assessment (MCA) that is employed for metric analysis. This paper compares Space Syntax (SS) and Multiple Centrality Assessment (MCA) by measuring the integration and centrality of the street, and highlights the points of similarity and difference between the two techniques.

Acetyleugenol is a phytochemical compound with broad effect against infectious diseases and tumors. Here, we extracted, characterized and elucidated the structure of acetyeugenol, for the first time, from the leaves of Acacia nilotica (L.)―a well-known medicinal plant. The broad antibacterial potential of acetyleugenol was first confirmed against seven bacterial pathogenic isolates with best activity against Proteus sp., Salmonella typhi, Staphylococcu aureus, and Streptococcus pneumonia, which showed similar or better zone of inhibition to that of the control amoxicillin. To further investigate its effect against Mycobacterium tuberculosis, acetyleugenol and its indole and phenyl analogs were subjected to molecular docking experiments against two potential tuberculosis drug targets―MtPknE and MtPknB Ser/Thr protein kinases. The results reveal that all of the analogs have improved docking scores comparing to the acetyleugenol. The indole analogs EUG-1 and EUG-3 were more effective with better docking scores for MtPknE with –11.08 and –10.05 kcal/mol, respectively. Similar results were obtained for the MtPknB. In contrast, only the EUG-2 phenyl analog has given rise to similar docking scores for both targets. This opens the door for further comprehensive studies on these acetyleugenol analogs with in vitro and in vivo experiments to validate and get more insights into their mechanisms of action.

Meningiomas are the most prevalent primary intracranial tumors. The majority are benign but can undergo dedifferentiation into advanced grades classified by World Health Organization (WHO) into Grades 1 to 3. Meningiomas tremendous variability in tumor behavior and slow growth rates complicate their diagnosis and treatment. A deeper comprehension of the molecular pathways and cellular microenvironment factors implicated in meningioma survival and pathology is needed. This review summarizes the known genetic and epigenetic aberrations involved in meningioma, with a focus on Neurofibromatosis type 2 (NF2) and non-NF2 mutations. Novel potential biomarkers for meningioma diagnosis and prognosis are also discussed, including epigenetic-, RNA-, metabolomics, and protein-based markers. Finally, the landscape of available meningioma-specific animal models is overviewed. Use of these animal models can enable planning of adjuvant treatment, potentially assisting in preoperative and postoperative decision-making. Discovery of novel biomarkers will allow, in combination with WHO grading, more precise meningioma grading, including meningioma identification, subtype determination, and prediction of metastasis, recurrence, and response to therapy. Moreover, these biomarkers may be exploited in the development of personalized targeted therapies that can distinguish between the 15 diverse meningioma subtypes.

COVID-19 infection is extremely dangerous for persons with comorbidities such as kidney disease and diabetes. Although many people of all ages and socioeconomic backgrounds have suffered due to this pandemic, those with underlying medical conditions like kidney disease and diabetes are more vulnerable to becoming infected with COVID-19 related to weak immunity. However, the role of vaccination in the co-infection of COVID-19 with diabetics is not available in the literature. Therefore, we examine the unique challenges presented by the co-infection of COVID-19 in individuals with diabetes, focusing on its disease transmission dynamics. A mathematical modelling technique is to be employed in this work to analyse the dynamics of COVID-19 outbreaks with seven compartments, including vaccination with comorbidities such as diabetes. We also investigated analytically by displaying the solutions' existence, boundedness, positivity and sensitivity. After calculating the basic reproduction numbers, the stability analysis of model equilibrium points is also covered. If the reproduction numbers are less than unity, the disease-free equilibrium points of the model appear to be both locally and globally stable. The findings of this study are that as the vaccination rate rises, the incidence of COVID-19 and its co-infections with diabetes decreases. Effective disease treatment strategies may be based partly on the possible impact of vaccination on the co-infection of COVID-19 related to diabetic disease insights.

Coronavirus that is also known as COVID-19 disease is produced by SARSCoV-2. This causative agent is highly contagious and can cause potentially fatal pneumonia worldwide with serious public health concerns. In the beginning among infected individuals, most of them were those who were mainly shown to the wet animal market in a big city of China known as Wuhan. So, it was suggested that this was almost certainly the zoonotic source of COVID-19illness. The transitional source of origin and their mode of transmission to humans were not known obviously. Conversely, from human to human rapidly transformation have been confirmed generally. Currently, there is no availability of FDA approved clinically antiviral drugs and/or vaccines to be used against the COVID-19. Afterward, SARS-CoV and MERS-CoV, the occurrence of SARS-CoV-2 has been manifested as the third sketch of an enormously pathogenic coronavirus into human population globally. In this review, we provide a brief overview of the history of COVID-19 in Pakistan up-to 18^th weeks after beginning, current situation, epidemiology, and its impact on the human population. Moreover, we focused on physiological variation during the incubation period, genome analysis of SARS-CoV2, supportive treatment approaches, and safety measures in the Pakistani population, which may be supportive for combating the risk of COVID-19 epidemic. We also reviewed the future approaches for the development of therapeutic interventions and vaccines to cope with the COVID-19 epidemic.

Structural perturbations in the Mn4CaO5 cluster site, an oxygen-evolving complex of photosystem II, such as those induced by Ca2+/Sr2+ exchanges or Ca/Mn-removal have been known to induce long-range positive shifts (+30 mV to +150 mV) in the redox potential of the primary quinone electron acceptor plastoquinone A (QA) located 40 Å distant from the OEC. Here, we reanalyzed the crystal structure of Sr-PSII solved at 2.1 Å and compare it with the native Ca-PSII of 1.9 Å with focus on the acceptor site and report on the possible long-range interactions between the donor, Mn4Ca(Sr)O5 cluster, and acceptor sites.

Background: The psychomotor agitation of the BPSD is one of the common issues in aged care facilities, leading to the poor functional and medical consequences. Psychotropic interventions are the preferable choice of treatment. But which medication should be the prescribers first preference? This review aims to compare pharmacological interventions for psychomotor agitation, judging them according to their effectuality and justifiability profiles. This is to be achieved by retrieving information from RCTs and systematic reviews. Objectives: This review evaluates evidence from RCTs, systematic reviews, and meta-analyses of BPSD patients who had taken agitation treatments. Assessing the efficacy of antidepressants and antipsychotic treatments when compared to each other for the purpose of improving agitation outcomes. Methods: This narrative review includes RCTs and retrospective studies that were comparing one or more active ingredient medications with another or with a placebo, along with sys-tematic reviews comparing antidepressants with antipsychotics such as quetiapine, olanzapine, and risperidone. Studies extracted by searching accessing databases, such as PubMed, OVID, and Cochrane with restrictions of date from 2000 to 2021 and English language. Quality of evidence: The quality of systematic reviews was judged against AMSTAR score, and RCTs were judged according to CONSORT checklist for RCT protocols. Conclusion: There are still few studies of serotonin targeting treatment of agitation in BPSD. The SSRIs such as citalopram were associated with a reduction in symptoms of agitation, and lower risk of adverse effects compared to antipsychotics. This review also illustrates brexpiprazole as a target of multimodal neurotransmitters such as dopamine, serotonin, and norepinephrine; and dextromethorphan, OR dextromethorphan associated with bupropion or quinidine as a blockade of NMDA receptors. The outcome of this review suggests that further studies involving more dementia/Alzheimer’s participants should be conducted. Future studies are required also to assess the long-term safety and efficacy of SSRI, brexpiprazole, dextromethorphan treatments for agitation in BPSD.

Good health and well-being is one of the essential SDGs that ensure healthy lives and promote well-being for all ages and further entails providing substantial medical services to the public at low cost and with minimal adverse effects on the environment. Information and communication technologies (ICTs) have taken on an increasingly important function as significant facilitators of healthcare reform, with the goals of enhancing access to health services, the quality of treatment provided, and the overall productivity of the healthcare system. However, the integration of ever-increasing ICT technologies into the healthcare systems, also referred to as digital transformation, is not a straightforward process, but it comes with different types of challenges from integration level to application design level and security level. Although several studies have been proposed to address the integration of ICT technologies into healthcare systems, there is still a need for a comprehensive research study on the integration and design challenges, security and privacy challenges, application areas, and possible positive and negative impacts. Therefore, this paper contributes as the research literature study covering an important SDG, "Good health and well-being," and its digital transformation, along with summarising our research findings in a detailed and taxonomical way. To start with, firstly, we present a detailed comparison of existing studies on healthcare and well-being, mainly focusing on integrating ICT technologies in healthcare in terms of sustainable aspects, security and privacy challenges, design and integration challenges, E-health-related applications, and future directions. We also present an overview and the need for digital transformation in healthcare, discuss its significant components, highlight E-health's importance and benefits, explore its integration and design challenges, and categorise the security and privacy challenges. Next, we present an in-depth discussion on the role of Blockchain technology as today's leading technology in E-health, discussing Blockchain technology and its characteristics, highlighting its benefits, and describing the possible types of Blockchain-based E-health use cases. Furthermore, we discuss the positive and negative impact of ICT integration along with identifying open issues and challenges of integrating ICT technologies into the healthcare systems and discuss future research directions, which provide the strength for researchers to address the issues in future solutions.

Antimicrobial resistance (AMR) is a major public health threat linked to increased morbidity and mortality. It has the potential to return us to the pre-antibiotic era. Antimicrobial stewardship (AMS) programs are recognized as a key intervention to improve antimicrobial use and combat AMR. However, implementation of AMS programs remains limited in Africa, particularly in Rwanda. This qualitative study, conducted at King Faisal Hospital (KFH) in Rwanda, aimed at assessing current prescription practices to identify areas for improvement and promote adherence to AMS principles. The interviews were recorded, transcribed, and thematically analyzed, revealing four emerging themes. First, emerged on AMS activities that were working well which includes availability of microbiology laboratory results, and prescription guidelines as factors influencing antibiotic prescription adjustments. Second, Implementations challenges to AMS which identified the prescription of broad-spectrum antibiotics, limited local data on AMR patterns, stock-outs of essential antibiotics, Thirdly, the importance of adhering to AMR management guidelines at KFH was underscored. Lastly, participant recommendations centered on regular training for healthcare workers, widespread dissemination of AMR findings across departments, and the enforcement of antibiotic restriction policies. These actions can improve prescription behaviors, upholding the highest standards of patient care, and strengthening the nascent AMS program.

Abstract: With the growing integration of the Internet of Things (IoT) in smart buildings, it is crucial to ensure the precise implementation and operation of wireless sensor networks (WSNs). This paper aims to study the implementation aspect of Wireless Sensor Networks (WSNs) in a commercial multi-story building, specifically addressing the difficulty of dealing with variable environmental conditions on each floor. This research addresses the disparity between simulated situations and actual deployments, offering valuable insights that have the potential to signifi-cantly improve the efficiency and responsiveness of building management systems. We obtain real-time sensor data to analyze and evaluate the system’s performance. Our investigation is grounded in the growing importance of incorporating WSNs into buildings to create intelligent environments. By leveraging the capabilities of Contiki operating system, this study employs a specialized simulator to generate simulated data, allowing for a comparison between real-world and simulated scenarios. We provide an in-depth analysis to scrutinize the disparities and commonalities between the datasets obtained from real-world deployments and simulated en-vironments. We highlight the necessity of precise simulation to validate real-life sensor data, shedding light on the challenges and opportunities associated with implementing WSNs in in-telligent buildings. Results obtained show the significance of accurate simulation models for re-liable data representation, providing a roadmap for further developments in the integration of WSNs into intelligent building scenarios. The findings highlight the potential for optimizing living and working conditions based on the real-time monitoring of critical environmental pa-rameters. This includes insights into temperature, humidity, and light intensity, offering oppor-tunities for enhanced comfort and efficiency in intelligent environments.

Recently, the number of vehicles on the road, especially in urban centers, has increased dramatically due to the increasing trend of individuals towards urbanization. As a result, manual detection and recognition of vehicles (i.e., license plates and vehicle manufacturer) become an arduous task and beyond human capabilities. In this paper, we have developed a system using transfer learning-based DL techniques for automatic identification of Jordanian vehicles. The YOLOv3 (You Only Look Once) model was re-trained using transfer learning to accomplish the license plate detection, character recognition, and vehicle logo detection. While VGG16 (Visual Geometry Group) model was retrained to accomplish the vehicle logo recognition. To train and test these models, four datasets have been collected. The first dataset consists of 7,035 Jordanian vehicle images, the second dataset consist of 7,176 Jordanian license plates, and the third dataset consists of 8,271 Jordanian vehicle images. These datasets have been used to train and test the YOLOv3 model for Jordanian license plate detection, character recognition, and vehicle logo detection, respectively. While the fourth dataset consists of 158,230 vehicle logo images used to train and test the VGG16 model for the vehicle logo recognition. Text measures were used to evaluate the performance of our developed system. Moreover, mean average precision (mAP) measure was used to evaluate the YOLOv3 model of the detection tasks (i.e., license plate detection and vehicle logo detection). For license plate detection, the precision, recall, F-measure, and mAP were 99.6%, 100%, 99.8%, and 99.9%, respectively. While for character recognition, the precision, recall, and F-measure were 100%, 99.9%, and 99.95%, respectively. The performance of license plate recognition stage was evaluated by evaluating these two sub-stages as a sequence, where the precision, recall, and F-measure were 99.8%, 99.8%, and 99.8%, respectively. Furthermore, for vehicle logo detection, the precision, recall, F-measure, and mAP were 99%, 99.6%, 99.3%, and 99.1%, respectively, while for vehicle logo recognition, the precision, recall, F-measure were 98%, 98%, and 98%, respectively. The performance of vehicle logo recognition stage was evaluated by evaluating these two sub-stages as a sequence, where the precision, recall, and F-measure were 95.3%, 99.5%, and 97.4%, respectively.

The present study finds the association of board characteristics (such as gender diversity, independence, female chairperson or/and female CEO, and board size) and the quality of Corporate Social Responsibility (CSR) disclosure of the top 100 Pakistan Stock Exchange (PSX) listed companies. Unlike most earlier studies in similar contexts, we have focused on CSR disclosure ‘quality’ and not ‘quantity’. We conducted the content analysis of secondary Corporate Governance (CG) and CSR data extracted from the annual reports of PSX-listed companies across ten industrial sectors from period of 2017 and 2018. Our empirical investigation through univariate and multiple regression analysis with Ordinary least squares (OLS) techniques revealed that all the board characteristics potentially have a significant association in lessening CSR disclosure quality. We acknowledge several research limitations, including the study time period and selected board characteristics. While our study has provided some understanding of the association of board characteristics with CSR disclosure quality of PSX-listed companies, several research gaps still need to be addressed. Future investigators should examine this association through the pre-COVID-19 and post-COVID-19 connections and the inclusion of a systems theory perspective.

Accurate measurement of solid precipitation (S) has a critical importance for proper understanding of the Earth’s hydrological cycle, validation of emerging technologies and weather prediction models, and developing parameterizations of severe weather elements such as visibility (Vis). However, measuring S is still a challenging problem mainly because of wind effects. The wind effects are normally mitigated by using a Double-Fence Automated Reference (DFAR) system to reduce the wind speed (Ug). To contribute towards addressing some of these issues we have analyzed data sets collected at a site located in Southern Ontario, Canada using several instruments. The instruments include two Geonor gauges, one placed inside a DFAR (SDFAR) and the other inside a double Alter shield (DASG), a Pluvio2 gauge inside a single Alter shield (SASP), a HotPlate, a PARSIVEL2 Disdrometer that measures S and fall velocity (V), and a FD12P senor that measures S and type and Vis. The results show that for the Ug observed in this study (Ug < 6 ms-1), both DASG and SASP have similar collection efficiency (CE) of near 70%. The transfer functions (TF) for DASG and SASP as a function of Ug and also Ug, and V have been derived. The TF for the DASG that includes both Ug and V showed better agreement with observation than just Ug alone. The S measured using all the other instruments were correlated well with SDFAR, but the PARSIVEL2 and FD12P overestimated and underestimated the snow amount respectively as compared the SDFAR. However, the HotPlate captured similar amount of S as the SDFAR. According to this study, the SDFAR showed good correlation with Vis.

This paper presents a concise exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been developed and deployed to synthesize the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that in spite of the fact that analytical methods may involve fair amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

Objective Objective of the study was to evaluate the public perception and acceptance of community pharmacists in providing mental health support in Saudi Arabia during COVID-19. Methods An online questionnaire-based cross-sectional study was carried out among the general public (aged 15 years or above) of Saudi Arabia during March-April 2020 using QuestionPro platform. The validated questionnaire was bilingual (English and Arabic), simple, detailed, and relevant to obtain focused responses from participants. Importantly, an item related to an agreement on a statement “Pharmacist can counsel people on psychological issues” was included on a five-point Likert scale. The survey link was shared across multiple social media platforms. Results A total of 773 participants completed the survey. The majority were female (65.2%) and youngsters (48.1%). Nearly half of the participants disagreed, while 19% agreed that pharmacists could provide support on psychological issues. Factors such as age, employment status, and the management of the psychological issues during the pandemic were significantly associated with the acceptance of community pharmacists’ role in providing mental health services (p

This paper investigates the potential of utilising multilevel quasi-interpolation techniques on Chebyshev sparse grids for complex numerical computations. The paper starts by laying down the motivations for choosing Chebyshev sparse grids and quasi-interpolation methods with Gaussian kernels. It delves into the practical aspects of implementing these techniques. Various numerical experiments are performed to evaluate the efficiency and limitations of the multilevel quasi-sparse interpolation methods with dimensions two dimension and three dimension. The work ultimately aims to provide a comprehensive understanding of the computational efficiency and accuracy achievable through this approach, comparing its performance with traditional methods.

Background: The biofilm-forming bacteria Porphyromonas gingivalis (P. gingivalis) is primarily responsible for periodontal disorders, which continue to be a global health issue. Despite the widespread use of antibiotics like metronidazole, other potent therapeutic a crucial quorum sensing molecule implicated in the formation of P. gingivalis biofilm. Approaches are now being explored due to the growing challenge of antibiotic resistance. Objective: In particular, chemicals from Symphytum Officinale (S) and Panax Ginseng (G) plants will be examined in this study to assess if they have the ability to inhibit biofilm and to prevent the development of acylated homoserine lactones (AHLs), a quorum sensing molecule. Materials and Methods: With Metronidazole serving as a control, the antibacterial effects of these substances (Symphytum Officinale and Panax Ginseng) were examined against a standard strain and a clinical isolate of P. gingivalis. Dilutions of these plant extracts were used either alone (G+S) or in conjunction with metronidazole (G+S+F), to assess their antibacterial activity using antibacterial susceptibility test (inhibition zone), biofilm inhibition and disruption assay (optical density) and quorum sensing inhibition assay (AHL). Results: The combinations of Symphytum officinale, Panax Ginseng and metronidazole (S+G+F) showed the maximum effectiveness with highest zone of inhibition (25.000±0.001 mm) and biofilm inhibition (98.46%), and were comparable to G+S (inhibition zone of 24.341±0.593 mm and biofilm inhibition of 97.76%), and significantly different in the degree of biofilm inhibition with different treatment scenarios. Additionally, the plant's extracts and combinations are specific concentrations had a significant effect on the suppression of the generation of AHL (p < 0.05). Conclusion: According to preliminary research, these plant-derived substances, especially when paired with metronidazole, significantly inhibited the growth of P. gingivalis biofilm providing valuable information for the development of innovative therapeutic approaches for periodontitis and other biofilm-associated illnesses.

This paper reports on the optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation systems for cattle farming in rural areas of Bangladesh. Bangladesh is a lower middle-income country with declining rates of poverty among its 160 million people due to persistent economic growth in conjunction with balanced agricultural improvements. Most of the rural households adopt a mixed farming system by cultivating crops and simultaneously rearing livestock. Among the animals raised, cattle are considered as the most valuable asset for the small/medium-scale farmers in terms of their meat and milk production. Currently, along with the major health issue, the COVID-19 pandemic is hindering the world’s economic growth and has thrust millions into unemployment; Bangladesh is also in this loop. However, natural disasters such as COVID-19 pandemic and floods, largely constrain rural smallholder cattle farmers from climbing out of their poverty. In particular, small and medium-scale cattle farmers face many issues that obstruct them from taking advantage of market opportunities and imposing a greater burden on their families and incomes. An appropriate measure can give a way to make those cattle farmers’ businesses both profitable and sustainable. Optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation system for cattle farming is a new and forward-looking approach for sustainable development of the livestock sector. In this study, we design and optimize a thin-film coating assisted hybrid (photovoltaic-battery-generator) power system by using the Hybrid Optimization of Multiple Energy Resources (HOMER, Version 3.14.0) simulation tool. An analysis of the results has suggested that the off-grid hybrid system is more feasible for small and medium-scale cattle farming systems with long-term sustainability to overcome the significant challenges faced by smallholder cattle farmers in Bangladesh.

Keywords: Requirements prioritization, Next release plan, Software product planning, Decision support, MoSCoW, AHP, K-Menas, GMM, BIRCH, PAM, Hierarchical, Clustering, Clusters Evaluation

The contemporary landscape of eHealth is characterized by major concerns related to electronic medical records (EMRs). In an EMR, critical patient health information gets its own repository, which is the core of the eHealth system. Notably, the EMR not only retrieves health information generated in ambulatory clinical settings but also includes court-generated records. These overlapping records assume the role of a foundational data source for a comprehensive electronic health record (EHR). This scholarly review sheds light on recent trends in medical records and associated challenges, while at the same time providing insights into Saudi Arabia’s targeted approaches to healthcare delivery. Additionally, the talk expands to include a description of blockchain technology and its underlying conceptual framework. This demonstration positions blockchain technology as a promising approach that requires consideration for future use in the healthcare system.

Bangladesh's railway system mostly uses typical manual railway crossing technique or boom gates through its 2,955.53 km rail route all over the country. The accidents are frequently happening in the railway crossings due to not having obstacle detectable and quickly operating gate systems, and also for fewer safety measures in the railway crossing. Currently, there are very few automatic railway crossing systems (without obstacle detectors) available, however, all of them are dependent on the national power grid without a backup plan for any emergency cases. Bangladesh is still running a bit behind in the power generation of its consumption, hence it is not possible to have a continuous power supply at all times all over the countryside. We aim to design and develop a smart railway crossing system with an obstacle detector to prevent common types of accidents in the railway crossing points. We design to use two infrared (IR) sensors to operate the railway crossing systems which will be controlled by the Arduino Uno. This newly designed level crossing system will be run with the help of sustainable renewable energy which is cost-effective, eco-friendly, and apply under the national green energy policy towards achieving sustainable development in Bangladesh as a part of the global sustainable goal to face climate change challenges. We have summarized the simulated results of several renewable energy sources including a hybrid system and optimized the Levelized Cost of Energy (LCOE), and the payback periods.

Background: The important periodontal disease pathogen Porphyromonas gingivalis produces large biofilms that increase its pathogenicity. Finding natural antimicrobial agents is crucial because of the rise in antibiotic resistance. Objective: The purpose of this study was to determine if plant extracts such as Symphytum officinale (S) and Panax ginseng (G) were effective against P. gingivalis separately and in combination with a common antibiotic Metronidazole (F). Materials and Procedures: Six different dilutions were produced the plant extracts and antibiotic separately and in combination with G and F and S and F using two-fold serial dilution technique. To evaluate the effects of these substances biofilm inhibition experiments were conducted. Plaque samples were collected from periodontitis patients to isolate P. gingivalis and standard strain of P. gingivalis (ATCC 33277) were bought. Additionally, Acylated Homoserine Lactones (AHLs) detection was carried out to look for any activity that would interfere with quorum sensing. GraphPad prism was used for statistical analysis with p value < 0.05. Results: The combinations of Symphytum Officinale and Metronidazole (S+F) showed the maximum effectiveness in biofilm inhibition (98.7%), which was better than G+F (98.2%) with substantial variations in biofilm inhibition levels in different treatment regimes. Notably, the isolate from the patient was more active than the standard strain. Additionally, the plant extracts and their combinations at particular dilutions had notable inhibitory effects on the generation of AHL (p <0.05). Conclusion: The study highlights the possibility of Symphytum Officinale and Panax Ginseng as effective treatments for P. gingivalis biofilm and AHLs, both on their own and in combination with Metronidazole. These organic substances may open the door to cutting-edge methods of treating periodontal disorders.

Introduction. Streptococcus pneumoniae infections are a major cause of mortality and morbidity worldwide. In Jordan, pneumococcal conjugate vaccines (PCVs) are not included in the national vaccination program. Due to the current availability of several PCVs including PCV-10, PCV-13 and PCV-15, along with PCV-20, currently undergoing pediatric approvals globally, the decision to introduce PCVs and their selection should be based on valid local data on the common serotypes of Streptococcus pneumoniae. Methods: This cross-sectional study aimed to identify the frequency of serotypes of Streptococcus pneumoniae in children aged below 5 years hospitalized with invasive pneumococcal diseases (IPD) including pneumonia, septicemia and meningitis during the study’s duration in representative areas of Jordan. Serotyping for culture-positive cases was based on the capsular reaction test, known as the Quellung reaction. qPCR was conducted on blood samples of patients with lobar pneumonia identified via X-ray or on cerebrospinal fluid for those with a positive latex agglutination test for Streptococcus pneumoniae. Results. This study was based on the analysis of the serotypes of 1015 Streptococcus pneumoniae cases among children younger than the age of 5; 1006 cases with pneumonia, 6 cases with meningitis, and 3 cases with septicemia. Only 23 culture-positive cases were identified, in comparison to 992 lobar pneumonia cases which were PCR-positive but culture-negative, with a PCR positivity rate of 92%. Serotypes 6B, 6A, 14 and 19F were the most common serotypes identified in the study, with prevalence rates of 16.45%, 13.60%, 12.12% and 8.18%, respectively. PCV-10, PCV-13, PCV-15 and PCV-20 coverage rates were 45.32%, 61.87%, 64.14% and 68.47%, respectively. Discussion: To the best of our knowledge, this is largest prospective study from the Middle East and one of the largest studies worldwide showing the serotypes of Streptococcus pneumoniae. It reveals the urgency for the introduction of PCV vaccination in Jordan, utilizing recently developed vaccines with broader serotype coverage.

Lamb wave-based structural health monitoring is widely acknowledged as a reliable 11 method for damage identification, classification, localization and quantification. However, due to 12 the complexity of Lamb wave signals, especially after interacting with structural components and 13 defects, interpreting these waves and extracting useful information about the structure's health is 14 still a major challenge. However, deep learning-based strategy offers a great opportunity to address 15 such challenges as the algorithm can operate directly on raw discrete time-domain signals. Unlike 16 traditional methods, which often require careful feature engineering and preprocessing, deep learn-17 ing can automatically extract relevant features from the raw data. This paper proposes an autoen-18 coder based on a bidirectional long short-term memory network with maximal overlap discrete 19 wavelet transform layer to detect the signal anomaly and determine the location of the damage in 20 the composite structure. This approach has the potential to greatly enhance our ability to detect and 21 locate structural damage in composite structures, thereby increasing safety and efficiency.

In addressing the challenges of data scarcity in biometrics, this study explores the generation of synthetic palmprint images as an efficient, cost effective, and privacy preserving alternative to real-world data reliance. Traditional methods for synthetic biometric image creation primarily involve orientation modifications and filter applications, with no established method specific to palmprints. We introduced the utilization of the “Style-based generator”, StyleGAN2-ADA, from the StyleGAN series, renowned for generating high-quality images. Furthermore, we explore the capabilities of its successor, StyleGAN3, which boasts enhanced image generation, facilitating smooth and realistic transitions. By comparing the performance of StyleGAN3 on public dataset, we aim to establish the most efficient generative model for this purpose. Evaluations were conducted using the SIFT (Scale-Invariant Feature Transform) algorithm into our evaluation framework. Preliminary findings suggest that StyleGAN3 offers superior generative capabilities, enhancing equivariance in synthetic palmprint generation.

In this work, we introduce a new concepts for $\alpha$-type $F$-Suzuki contraction and $\alpha$-type $F$-weak-Suzuki contraction in the context of $b$-metric spaces. Compared to the $\alpha$-type $F$-contraction and $F$-Suzuki contraction mappings, these contractions are essentially weaker. For these type of contraction mappings, sufficient conditions are established for the fixed point's existence and uniqueness in $b$-metric spaces. As a result, the findings encompass several generalizations. To show the usability of our obtained results, we provide a supportive example and an application to a non-linear differential equation with fractional order.

The calculation of effective doses is crucial in many medical and radiation fields, in order to ensure safety and compliance with regulatory limits. Traditionally, Monte Carlo codes using detailed human body computational phantoms have been used for such calculations. Monte Carlo dose calculations can be time-consuming and require expertise in different processes when building the computational phantom and dose calculations. This study employs various machine learning (ML) algorithms to predict the organ doses and effective dose conversion coefficients (DCCs) for different anthropomorphic phantoms. A comprehensive data set comprising neutron energy bins, organ labels, masses, and densities is compiled from Monte Carlo studies, and is used to train and evaluate the supervised ML models. This study includes a broad range of phantoms, including those from the International Commission of Radiation Protection (ICRP-110, ICRP-116 phantom), the Visible-Human Project (VIP-man phantom), and the Medical Internal Radiation Dose Committee (MIRD-Phantom), with row data prepared using numerical data and organ categorical labeled data. Extreme gradient boosting (XGB), gradient boosting (GB), and the random forest-based Extra Trees regressor are employed to assess the performance of the ML models against published ICRP neutron DCC values using the mean square error, mean absolute error, and R² metrics. The results demonstrate that the ML predictions significantly vary in lower energy ranges and vary less in higher neutron energy ranges, while showing good agreement with ICRP values at mid-range energies. Moreover, the categorical data models align closely with the reference doses, suggesting the potential of ML in predicting effective doses for custom phantoms based on regional populations, such as the Saudi voxel-based model. This study paves the way for efficient dose prediction using ML, particularly in scenarios requiring rapid results without extensive computational resources or expertise. The findings also indicate potential improvements in data representation and the inclusion of larger data sets to refine model accuracy and prevent overfitting. Thus, ML methods can serve as valuable techniques for the continued development of personalized dosimetry.

A case report of the diagnosis of Long Term Sequelae of West Nile Neuroinvasive Disease in a patient with 9 years history. Empirical data of symptoms and test reports has been presented and based on the available data likely pathogenesis of the disease has been discussed. The empirical data has been compared to the published literature to reach a highly confident diagnosis.

The study conducts a comparative analysis of solar radiation estimation methods, assessing the efficacy of the Heliosat-2 algorithm against ground measurements across seven distinct countries: Netherlands, Spain, Japan, Namibia, South Africa, Saudi Arabia, and India. To achieve this, it utilizes two distinct satellite data sources—Himawari-8 for Japan and Metosat Second Generation-MSG for the rest of the countries—spanning the years Jan 2022 to April 2024. A robust methodology for determining albedo parameters specific to Heliosat-2 was developed. During cloudy days, the estimates provided by Heliosat-2 generally exceeded the ground measurements in all the countries. Conversely, on clear days, there was a tendency for underestimation, as indicated by the median value of the mean bias (MB) across most of the countries. The Heliosat-2 model slightly underestimates daily radiation values, with a median MB ranging from −27.5 to +10.2 W.m⁻². Notably, the median root mean squared error (RMSE) on clear days is significantly lower, with values ranging from 24.8 to 108.7 W.m⁻², compared to cloudy days where RMSE values lie between 75.3 and 180.2 W.m⁻². In terms of R² values, both satellites show a strong correlation between the estimated and actual values, with a median value consistently above 0.86 on a monthly scale and over 92% of daily data points falling within ±2 standard deviation.

Citizen Science has come up to perform analytics over the SARS-CoV-2 genome. Public GALAXY servers provide an automated platform for genomics analysis. Study includes design of GALAXY workflows for RNASEQ assembly and annotation as well as genomic variant discovery and perform analysis across four samples of SARS-CoV-2 infected humans obtained from the local population of Wuhan, China. It provides information about transcriptomics and genomic variants across the SARS-CoV-2 genome. Study can be extended to perform evolutionary and comparative study across each species of coronaviruses. Augmented and integrated study with cheminformatics and immunoinformatics will be a way forward for drug discovery and vaccine development.

This paper proposes an ARIMA approach to battery health forecasting with accuracy improvement by K shape-based clustered predictors. The health prediction of the battery pack is an important function of a battery management system in data centers. Accurate forecasting of battery life turns out to be very difficult without failure data to train a good forecasting model in real life. The conventional ARIMA model is compared with total and clustered predictors for battery health forecasting. Results show that the forecasting accuracy of the ARIMA model significantly improved by utilizing the results of the clustered predictors for 40 batteries in a real data center. One year of actual historical data of 40 batteries of large scale datacenter is presented to validate the effectiveness of the proposed methodology.

Informal settlements pose multifaceted challenges to urban development, necessitating a reconsideration of traditional upgrading approaches. This study examines the integration of the Street-Led Approach within the Ezbit Hegazi informal settlement, leveraging the Alexandria University Centre of Excellence for Smart Urban Governance's (ALEXU-CoE-SUG) innovative framework. It highlights the centrality of 'Demand for Good Governance' (DFGG) practices in bridging the gap between governmental (supply-side) and community (demand-side) objectives, fostering a collaborative urban upgrading process. Through an in-depth case study analysis, this paper reveals the potential of aligning governmental agendas with local aspirations, emphasizing the importance of local dynamics in sustainable urban development. The findings contribute to the urban studies literature by providing insights into the synergies between supply and demand perspectives in the context of informal settlement upgrading, offering implications for policy and practice in similar urban settings globally.

In videos, the human's actions are of three-dimensional (3D) signals. These videos investigate the spatiotemporal knowledge of human behavior. The promising ability is investigated using 3D convolution neural networks (CNNs). The 3D CNNs have not yet achieved high output for their well-established two-dimensional (2D) equivalents in still photographs. Board 3D Convolutional Memory and Spatiotemporal fusion face training difficulty preventing 3D CNN from accomplishing remarkable evaluation. In this paper, we implement Hybrid Deep Learning Architecture that combines STIP and 3D CNN features to enhance the performance of 3D videos effectively. After implementation, the more detailed and deeper charting for training in each circle of space-time fusion. The training model further enhances the results after handling complicated evaluations of models. The video classification model is used in this implemented model. Intelligent 3D Network Protocol for Multimedia Data Classification using Deep Learning is introduced to further understand space-time association in human endeavors. In the implementation of the result, the well-known dataset, i.e., UCF101 to, evaluates the performance of the proposed hybrid technique. The results beat the proposed hybrid technique that substantially beats the initial 3D CNNs. The results are compared with state-of-the-art frameworks from literature for action recognition on UCF101 with an accuracy of 95%.

Saudi Arabia consists mainly of desert land. However, it has big and small natural wetlands and artificial wetlands. Most of these wetlands are seen along the Red Sea and the Arabian Gulf coastal regions. Al-Asfar Lake, located in the Eastern Region of Saudi Arabia, is one of the historical landmarks of Al-Ahsa province. The primary lake water source is agricultural drainage water, which some refer to as an artificial lake. This paper mainly aims to reflect shade on the wetlands in Saudi Arabia in general and to show in detail the environmental impacts of Al-Asfar Lake on the ecosystem and biodiversity of the study area. The analytical review of the previous studies conducted in Al-Asfar Lake was adopted in this article. Hence, the impact of the lake on the land-use system, water quality and biodiversity was illustrated as the main outputs of the review analysis. However, the sustainable management of Al-Asfar Lake requires the stakeholders to adopt the wetland ecosystem health concept, which might lead to improving the lake's environmental conditions.

There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

Bioconvective flows have attracted attention in recent years due to actual and potential applications. In this paper, we consider a steady and laminar convective MHD flow of a nanofluid with heat, mass and microorganism transfer with a heat source/sink present. In addition, we assume there exists a first order chemical reaction. The governing partial differential equations (PDEs) are reduced to ordinary differential equations (ODEs) using the scaling group transformation and the associated boundary value problem is then solved. The influences of selected governing parameters on the dimensionless velocity, temperature, nanoparticle concentration, density of motile microorganisms, skin friction, heat transfer, mass transfer, and motile microorganism density rates are computed and discussed

Abstract Incretin mimetics, also known as glucagon-like peptide-1 (GLP-1) receptor agonists, are a class of medications used to treat type 2 diabetes by mimicking the actions of incretin hormones in the body. These hormones are responsible for promoting insulin release from the pancreas in response to nutrient intake, as well as decreasing glucagon secretion, slowing gastric emptying, and promoting satiety. By imitating these actions, incretin mimetics help to regulate blood sugar levels in individuals with diabetes and glucose intolerance. One of the key benefits of incretin mimetics is its ability to lower blood sugar levels without causing hypoglycemia. This is especially important for individuals with diabetes who may experience dangerous drops in blood sugar levels when using other medications. Additionally, incretin mimetics have been shown to promote weight loss in some individuals, making them a valuable option for those struggling with obesity in addition to diabetes. Incretin mimetics are administered by injection, once or twice daily, depending on the specific medication. They are often combined with other diabetes medications, such as metformin or insulin, for optimal blood sugar control. These medications are generally well-tolerated, with common side effects including nausea, vomiting, and diarrhea, which usually diminish over time as the body adjusts to the medication. Studies have shown that incretin mimetics can help improve cardiovascular outcomes in individuals with diabetes, including reducing the risk of heart attacks and strokes. This is particularly significant given the increased risk of cardiovascular disease in individuals with diabetes. Incretin mimetics also have been shown to preserve pancreatic beta-cell function, which is responsible for producing insulin. This can help slow the progression of diabetes and reduce the need for higher insulin doses over time. Despite their many benefits, incretin mimetics are not without limitations. They can be expensive compared to other diabetes medications, which may make them less accessible for some individuals. Additionally, there have been concerns about the potential risk of pancreatitis and pancreatic cancer associated with the use of these medications. However, more research is needed to fully understand these risks. It is important for healthcare providers to carefully assess each individual's unique needs and medical history when considering the use of incretin mimetics. They may not be appropriate for everyone, particularly those with a history of pancreatitis or pancreatic cancer. Patients should also be educated about these medications' proper administration and potential side effects to ensure their safety and efficacy. Overall, incretin mimetics have emerged as an important therapeutic option for individuals with type 2 diabetes, offering a unique mechanism of action that can help improve blood sugar control, promote weight loss, and reduce cardiovascular risk. With ongoing research and development in this field, incretin mimetics continue to show promise as valuable tools in managing diabetes and its associated complications and comorbidities.

Quasi-interpolation is a powerful tool for approximating functions using radial basis functions (RBFs) such as Gaussian kernels. This avoids solving large systems of equations as in RBF interpolation. However, quasi-interpolation with Gaussian kernels on compact intervals can have significant errors near the boundaries. This paper proposes a quasi-interpolation method with Gaussian kernels using Chebyshev points and boundary corrections to improve the approximation near the boundaries. The boundary corrections use a linear approximation of the function beyond the interval to estimate the truncation error and add correction terms. Numerical studies on test functions show that the proposed method reduces errors significantly near boundaries compared to quasi-interpolation without corrections, for both equally spaced and Chebyshev points. The convergence and accuracy with the boundary corrections are generally better with Chebyshev points compared to equally spaced points. The proposed method provides an efficient way to perform quasi-interpolation on compact intervals while controlling the boundary errors.

The concept of distributed generation has made photovoltaic an integral source of energy in smart grid systems, especially in peer-to-peer energy trading frameworks that exploit excess power to fulfill the energy requirements of consumers in cost-efficient and eco-friendly manner. It is believed that P2P energy trading will dominate a significant portion of research in forthcoming power generation systems due to the excessive rise of energy demands across the globe. Despite a plethora of studies on energy optimization solutions in P2P trading, minimizing nanogrid energy trading cost and efficient energy sharing between consumers and prosumers are deemed among the challenging problems. This study overcomes essential issues overlooked by the contemporary P2P energy trading models by introducing a predictive optimization-oriented nanogrid energy trading model. The proposed study encompasses two stages: (1) predictive optimization model which harnesses BD-LSTM-based forecasted energy parameters (energy load, energy consumption, and PV generation) that are later incorporated in PSO-enabled objective function to reduce nanogrid trading cost, (2) optimal energy sharing plan is devised to decide the role of nanogrids as prosumers or consumers by emphasizing the use of PV-produced energy. The proposed model is validated on the case study containing nanogrid houses data. The simulation provides detailed experiments by comparing the energy demand and response using the proposed energy sharing model. The outcomes yield that the energy sharing plan holds a significant potential to fulfill maximum energy requirements of nanogrid house in P2P cluster and significantly reduces the energy cost compared to grid.

This study explores the potential of Eisenia fetida (Savigny) in vermicompost production within vermipits during winter months in the Rampur region of Uttar Pradesh, India. The vermipits were inoculated with 0.33 kg of E. fetida per pit, against the recommended rate of inoculation for assessment of real-time potential of earthworm on seasonal and regional grounds. The results revealed a significant increase in earthworm population, with three times production (4.1 kg) of the inoculated number (1.0 kg). The productivity dynamics of compost vs E. feida revealed a notable threefold and fourfold effectiveness, respectively. This dual advantage signifies the success of composting process, with the increased worm population indicating enhanced decomposition. The study attributes the combination of regional and edaphic factors viz., sandy loam soil with high humus content and good water passage, facilitating earthworm survival, reproduction and decomposition of agricultural waste. The loose and perforated soil structure allowed easy penetration of earthworms, transforming the soil into fertile compost. The research emphasizes the importance of soil moisture of semi-arid ecosystems thus highlighting the seasonal significance governing earthworm activity. The study provides insights into the mechanical ability of earthworms, its sensitivity to soil compaction and the influence of high hydration of the region. Inoculation during the winter period indicates increased earthworm activity setting the stage for enhanced compost production in the upcoming hot periods of summer months. The findings suggest that optimizing vermicomposting practices with altered feeding stocks, could further improvise compost and earthworm production and productivity in subsequent seasons. The study contributes for sustainable utilization of E. fetida in composting, its regional and seasonal efficacy turns trash to treasure for enhanced agricultural efficacy.

In dry season paddy farming, the alternate wetting and drying (AWD) irrigation improves water productivity, paddy production, and has the potential to decrease greenhouse gas (GHG) such as methane (CH4) and nitrous oxide (N2O) emissions when compared to continuous flooding (CF). However, there is a lack of research in Bangladesh on the effects of water management on CH4 and N2O emissions. During November 2017–April 2018, participatory on-farm trials were conducted at Feni and Chattogram districts of Bangladesh. Total 105 farmers comprising 20-hectare of land (62 farmers at Feni and 43 farmers at Chattogram district, each location having 10 hectare of land). We compared irrigation water and cost reductions, paddy yield, and CH4 and N2O emissions from paddy fields irrigated using AWD and CF irrigation methods. The CH4 and N2O emissions were determined using the Cool Farm Beta-3 methodology, and the global warming potential (GWP) was estimated using the Intergovernmental Panel on Climate Change-2014 standard approach. The mean results of randomly selected 30 farmers from two locations (15 of each) showed that AWD remarkably decreased irrigation water consumption by about 24% and increased water productivity by 224%. We estimated 23% savings for irrigation costs in AWD. By this time, AWD improved paddy production by 3% over CF. The AWD irrigation resulted in a 47% reduction in cumulative CH4 emissions having a lower CH4 emission factor (0.74 kg ha-1 day-1) than CF (1.39 kg ha-1 day-1). There was no obvious difference in N2O emission between AWD and CF. When compared to CF, AWD decreased the overall GWP by 27% and lowered the GHG intensity by 42%. The CH4 and N2O emissions did not differ substantially between Feni and Chattogram.

Abstract: A punicalagin is a metabolic product of pomegranate fruits and peeled. We have compiled the recent literature review from different sources. The extract of pomegranate fruits and peel has been reported for health-beneficial properties in inflammation-associated chronic disease and the regulatory role in NF-KB, MAPK, IL-6/JAK/STAT3, and PI3K/AKT/mTOR signaling pathway. Punicalagin is an ellagitannin found in the peel of pomegranate (Punica granatum). It is a polyphenol with proven biological/pharmacological activities like antioxidant, hepatoprotective, an-ti-atherosclerotic, anti-cancer, anti-neurological, anti-diabetic, and anti-digestive. The extracts have a rich source of hydrolyzable tannin and anthocyanin exhibiting strong anti-neoplastic properties. Anti-cancer activities of pomegranate with reference to modulated signaling pathways in various cancer diseases have been recently reported. The punicalagin-induced redirection of the signal-transduction pathway from survival and proliferation into the cell cycle by arrested the living cells. Apoptosis senescence and autophagy and thus compromising neoplastic progression are delineated. This review is based mainly on data obtained from various sources including the in-vitro cell line model and its activities that are concerned with the effect of punicalagin activities on various cell types.

There is a case about a system comprising two queues of M/M(a)/1/K with a due date with FCFS service policy in each queue. Using the methods of simulation and mathematical analysis, the solution diagrams were illustrated for the fixed due date Ɵ=1 second at the phase of due date up to the commencement of the service, limited capacity K₁=5 and K₂=4, for both scenarios of different service management rate resulted. For the analytical solution, first, a SAN model from the system was created in the Mobius tool. For simulation, a java discrete systems simulation code was used. Adjustment of the initial values, selection of the scenarios for service rate, the number of the consumers in the simulation, etc. were all carried out in the simulation code.

The year 2022 was characterized by several major events that impacted the business world in Indonesia and even globally after the COVID-19 pandemic devastated all business sectors in Indonesia and the world. The current business environment is experiencing accelerating turbulence characterized by increasing intensity of business competition, rapid changes in the market, and industrial connections climate. The industrial connection climate of an institution can be measured by the pattern of relationships that occur between workers and management. Industrial connections are fundamental to the sustainability of an organization and are understood as an important factor in influencing institutional performance. This research aims to look at the impact of the existence of industrial connections instruments, turbulence in the business environment on the industrial connections climate. Besides, how the industrial connections climate relates to firm performance. The research design is an inferential quantitative, using sampling and snowball sampling methods with total sample are 406. The data collected were analyzed using Structural Equation Model using LISREL version 8.70. This research used a survey to build an SEM model that tested the effect of organizational turbulence and industrial connections instruments on organizational climate directly, and tested mediation on organizational performance. All related indicators have outer loading more than 0.5 and T-value more than 1.96. Therefore, the conclusion is that all measurements are valid. Composite Reliability (CR) and VE for all indicators are >0.7 and >0.5 respectively. This research shows that industrial assosiation climate has a positive effect on business turbulence and industrial connections instruments. However, industrial connections instruments show a greater impact on the assosiation climate. This is because industrial connections instruments are the media used in the implementation of industrial connections in organizations. This research also confirms that industrial assosiation climate is positively related to organizational performance. The result of the indirect influence (IE) of 0.20 with t value is 8.47 means that the climate of Industrial connections is able to mediate the influence of Industrial connections Facilities on Organizational Performance.

This study introduces a novel nanocomposite coating composed of PANI/CeO2 nanocomposite films, aimed at addressing corrosion protection needs. Analysis through FTIR spectra and XRD patterns confirms the successful formation of the nanocomposite films. Notably, the PANI/CeO2 nanocomposite films exhibit a hydrophilic nature. The bandgap energy of the PANI composite film measures at 3.74 eV, while the introduction of CeO2 NPs into the PANI matrix reduces the bandgap energy to 3.67 eV. Furthermore, the electrical conductivity of the PANI composite film is observed to be 0.40 S.cm-1, with the incorporation of CeO2 NPs leading to an increase in electrical conductivity to 1.07 S.cm-1. To evaluate its efficacy, electrochemical measurements were conducted to assess the corrosion protection performance. Results indicate a high protection efficiency of 92.25% for the PANI/CeO2 nanocomposite film.

Water scarcity is a significant challenge facing Jordan today. It is a challenge in all areas that use water, and it has become certain that water is the critical factor in the population/resources equation. The water resources in Jordan have become limited with the noticeable increase in the population, mostly resulting from forced migrations in neighboring countries because of the wars and until our time. The rising natural population growth rate, along with the massive influx of refugees, has turned into a state of disproportion between the daily consumption of the population and the amount of water available. That Jordan shares most of its surface water resources with neighboring countries has exacerbated the situation. The current use of water already exceeds its renewable supply. Excessive withdrawal from aquifers, which leads to a lowering of the water table and deterioration in water quality, covered the deficit. This paper focuses on assessing the water situation in Jordan, mainly evaluating this problem and the solution being considered, the true basis for a sustainable water solution requires awareness by the population, and several governmental and non-governmental organizations are actively involved in educating residents about water shortages. The most important and 'actionable' elements of comprehensive water solutions are discussed in this paper, and these elements exist, develop extra water supplies, water harvesting, water desalination, proper wastewater reuse in the agricultural sector, and reduce the demand for drinking water. This research provides specific recommendations to address the shortage of water resources in the Kingdom and highlights the importance of water conservation and optimal use.

Aim of the study: To draw inferences from a retrospective evaluation of PSMA PET CT scans performed for the evaluation of biochemical recurrence. Material and Methods: Retrospective analysis of 295 PSMA PET CT scans spanning 3 years between 2020 and 2022 was undertaken. Results: Of 295 PET CT scans, 179 were positive, 66 negative and 50 had indeterminate findings. In positive group, 67 had radical prostatectomy and PSMA avid lesions were seen most commonly in pelvic lymph nodes. Remaining 112 positive scans, in non-radical prostatectomy group; 25 had recurrence only in prostate, 17 had recurrence involving prostate bed; 28 had no recurrence in prostate gland, while 42 had recurrence in prostate as well as extra prostatic sites. Overall, in non-prostatectomy group, 75 % population was harbouring a PSMA avid lesion in prostate gland while in remaining 25% population recurrence did not involve prostate gland. Majority of indeterminate findings were seen in small pelvic or retroperitoneal lymph nodes or skeletal regions (ribs/others) and in 9 patients indeterminate focus was seen in the prostate bed only. Follow up PSMA PET CT was helpful in prior indeterminate findings and unexplained PSA rise. Conclusion: A higher recurrence in prostate bed while evaluating biochemical recurrence prompts us to think; whether prostatectomy should be offered more proactively? Follow up PSMA PET CT is helpful for indeterminate findings; a PSA rise of 0.7 ng/ml in 6 months can result in positive PSMA PET CT while negative scan can be seen upto 2ng/ml PSA rise in 6 months.

A convolutional neural network (CNN) is sometimes understood as a black box in the sense that while it can approximate any function, studying its structure will not give us any insights into the nature of the function being approximated. In other terms, the discriminative ability does not reveal much about the latent representation of a network. This research aims to establish a framework for interpreting the CNNs by profiling them in terms of interpretable visual concepts and verifying them by means of Integrated Gradient. We also ask the question, "Do different input classes have a relationship or are they unrelated?" For instance, could there be an overlapping set of highly active neurons to identify different classes? Could there be a set of neurons that are useful for one input class whereas misleading for a different one? Intuition answers these questions positively, implying the existence of a structured set of neurons inclined to a particular class. Knowing this structure has significant values; it provides a principled way for identifying redundancies across the classes. Here the interpretability profiling has been done by evaluating the correspondence between individual hidden neurons and a set of human-understandable visual semantic concepts. We also propose an integrated gradient-based class-specific relevance mapping approach that takes the spatial position of the region of interest in the input image. Our relevance score verifies the interpretability scores in terms of neurons tuned to a particular concept/class. Further, we perform network ablation and measure the performance of the network based on our approach.

Triple negative breast cancer (TNBC) is the most aggressive breast cancer accounting for around 15% of identified breast cancer cases. TNBC, by lacking estrogen receptor (ER), progesterone receptor (PR), and human epidermal growth factor receptor 2 (HER2), is unresponsive to current targeted therapies. Existing treatment relies on chemotherapeutic treatment but, despite an initial response to chemotherapy, the inception of resistance and relapse is unfortunately common. Dasatinib is an approved second-generation inhibitor of multiple tyrosine kinases and literature data strongly support its use in the management of TNBC. However, dasatinib binds to plasma proteins and undergoes extensive metabolism through oxidation and conjugation. To protect dasatinib from fast pharmacokinetic degradation and to prolong its activity, it was encapsulated on poly(styrene-co-maleic acid) (SMA) micelles. The obtained SMA-dasatinib nanoparticles (NPs) were evaluated for their physicochemical properties, in vitro antiproliferative activity in different TNBC cell lines, and in vivo anticancer activity in a syngeneic model of breast cancer. Obtained results showed that SMA-dasatinib is more potent against 4T1 TNBC tumor growth in vivo compared to free drug. This enhanced effect was ascribed to the encapsulation of the drug protecting it from a rapid metabolism. Our finding highlights the often-overlooked value of nanoformulations in protecting its cargo from degradation. Overall, results may provide an alternative therapeutic strategy for TNBC management.

Hospital Pulau Pinang is the general hospital in Malaysia which targeting energy savings of 10% within five years from 2015 and other sustainability targets such as 3-star Energy Management Gold Standard and Green Building Certification. The targets are beneficial for the hospital itself to establish the Smart Building Program to improve its energy efficiency concurrent with the green policy of the Ministry of Health Malaysia and Sustainable Development Goals by the United Nations. This paper reviews the background of Hospital Pulau Pinang energy data , energy consumption trending, energy-saving trending, and energy conservation measures taken for the hospital from 2015 to December 2021.The yearly energy consumption baseline taken in 2016 was 27,496,731.00 kWh. It reduced significantly to 21,356,063 kWh in 2021 due to energy conservation measures. As a result, Hospital Pulau Pinang has achieved energy-saving about 16% at approximately RM7.3 million reduction in operational expenditure. The main objective of this paper is to provide further potential energy savings by studying the energy reduction by implementing solar photovoltaics using the simulation method. The simulation method can predict that Hospital Pulau Pinang can achieve another 5,130,000 kWh energy savings annually. This type of simulation has never been done before at a public hospital, and it will give further enhancing strategies to the Smart Building Program itself. Furthermore, the potential of smart building can be maximized to the next level by simulation, which helps the hospital energy committee make the potential decision on the energy-saving investment.

Carbon sequestration via carbon capture and storage (CCS) method is one of the most useful methods to lower the CO₂ emission in the atmosphere. Ethylenediamine (EDA) and triethylenetetramine (TETA) modified mesoporous carbon (MC) has been successfully prepared as CO₂ storage materials. The effect of various concentrations of EDA or TETA added to MC as well as activated carbon (AC) on their CO₂ adsorption capacity were investigated using high purity CO₂ as feed and titration method to quantitatively measure the amount of adsorbed CO₂. The results showed that within 60 min adsorption time, MCEDA49 gave the highest CO₂ capacity adsorption (19.68 mmol/g), followed by MC-TETA30 (11.241 mol/g). The improvement of CO₂ adsorption capacity at low TETA loadings proved that the four amine functional groups in TETA gave advantages to CO₂ adsorption. TETA functionalized MC has a potential to be used as CO₂ storage materials as it is used at low concentration. Therefore, it is more benign and friendly to the environment.

To obtain drop-in fuel properties from non-feed biomass, we herein report the catalytic hydrotreatment of microalgae biocrude, produced from hydrothermal liquefaction (HTL) of Spirulina. Our contribution focuses on the effect of temperature, initial H2 pressure, and residence time on the removal of heteroatoms (O and N). In contrast to common hydrotreating experimental protocols at batch scale, we devised a set of two-level factorial experiments and studied the most influential parameters affecting the removal of heteroatoms. It was found that up to 350 °C, the degree of deoxygenation (de-O) is mainly driven by temperature, whereas the degree of denitrogenation (de-N) also relies on initial H2 pressure and temperature-pressure interaction.Based on this, complete deoxygenation was obtained at mild operating conditions (350 °C), reaching a concurrent 47 % denitrogenation. Moreover, three optimized experiments are reported with 100 % removal of oxygen. In addition, the analysis by GC-MS and Sim-Dis gives insight to the fuel quality. The distribution of heteroatom N in lower (<340 °C) and higher (>340 °C) fractional cuts is studied by a fractional distillation unit following ASTM D-1160. Final results show that 63-68 % of nitrogen is concentrated in higher fractional cuts.

Intensive care nurses are highly prone to occupational stress and burnout, affecting their physical and mental health. The occurrence of the pandemic and related events increased nurses’ workload and exacerbated stress and burnout. We conducted a prospective longitudinal mixed-methods study with a cohort of nurses working in a medical ICU (COVID unit; n = 14) and cardiovascular ICU (non-COVID unit; n = 5). Each participant was followed for six 12-hour shifts. Validated questionnaires measured occupational stress and burnout prevalence. Wrist-worn wearable technologies recorded physiological indices of stress. Participants elaborated on the contributors to stress via post-study questionnaire. Data were analyzed using statistical and qualitative methods. Participants who cared for COVID patients at the COVID unit were 3.71 times more likely to experience stress (p &lt; .001) in comparison to non-COVID unit participants. No differences in stress levels were found when the same participants worked with COVID and non-COVID patients at different shifts at the COVID unit. The cohorts expressed similar contributors to stress including communication tasks, patient acuity, clinical procedures, admission processes, proning, labs, and assisting coworkers. Nurses in COVID units, irrespective of whether they care for a COVID patient, may experience high occupational stress and burnout.

Migraine is a primary headache disorder with a prevalence of 11.6% globally and 27% in Saudi Arabia. Irritable bowel syndrome has a prevalence of 9.2% worldwide. The prevalence of IBS has not been established nationally. However, provincial studies for both migraine and IBS have been conducted across the nation. There is a significant link between migraines and IBS globally. This identifies an association that needs to be investigated in a nationwide manner. This study aims to observe the association and the relationship between migraine and irritable bowel syndrome in Saudi Arabia. A cross-sectional study was conducted between March 2021 to June 2021 among the general population of Saudi Arabia, whose ages are 15 years old or greater. The data collection tools included MS-Q for migraine symptoms, MIGSEV scale for severity of migraine, and The IBS module of the Rome IV Diagnostic Questionnaire (R4DQ) for IBS symptoms and its subtype. With a total of 2802 participants, the majority of the study sample were males, who constituted 52.5%. Among the study's sample, the prevalence of migraine consisted of 27.4%, and the prevalence of IBS was 16.4%. The odds of having IBS in migraineurs were much higher than in those without migraines (OR 4.127; 95% CI 3.325-5.121), and the association was statistically significant (P&lt;0.001). In conclusion, there is a strong association between migraine and irritable bowel syndrome in Saudi Arabia.

The wettability of the oil-brine-rock systems is very challenging mainly for the carbonate reservoirs and it plays a significant role to enhance the oil recovery (EOR). Carbonate rocks are mad-up of complex lithology, hence these requires careful treatments in controlling their wetting behavior for enhanced oil recovery. Therefore, it is extremely important to modify their wettability from an oil-wet rock behavior to a water-wet so that the residual oil can be produced efficiently. Thus, the present study has examined the effectiveness of alumina nanofluid as well as a new chemical methyl blue to alter the wettability. The methyl blue is released on massive scale from various industries i.e. pharma, textile and food industry which is a key environmental concern which contaminates the water table. Hence the study, explores the effects of MB and alumina nanofluid on the wettability. The effect of nanofluids formulated via dispersing the alumina nanoparticles in aqueous solutions at various concentration (0. 0.05, 0.3, 0.50, 0.75 and 1.0 wt. %) were tested for wettability modification under different physio-thermal conditions. Subsequently, the wettability change was examined for the samples treated with different concentrations of MB (10, 15, 30, 50 and 100 mg/L) for 7-days at two different temperatures of (25 and 50 0C). The results showed that hydrophobicity of the SML carbonate rock has significantly reversed while treating with alumina nanofluids and MB. Thus, the wettability modification/reversal via treatment of MB and alumina nanofluid can be an effective mechanism to hydrogen injection and for EOR processes.

In this paper, we compile the fractional power series method and the Laplace transform to design a new algorithm for solving the fractional Volterra integro-differential equation. For that, we assume the Laplace power series (LPS) solution in terms of power q=1m,m∈Z+, where the fractional derivative of order α=qγ for which γ∈Z+. This assumption will help us to write the integral, the kernel, and the nonhomogeneous terms as a LPS with the same power. The recurrence relations for finding the series coefficients can be constructed using this form. To demonstrate the algorithm's accuracy, the residual error is defined and calculated for several values of the fractional derivative. Two strongly nonlinear examples are discussed to provide the efficiency of the algorithm. The algorithm gains powerful results for this kind of problem. Under Caputo meaning the obtained results are illustrated numerically, and graphically. Geometrically, the behavior of the solution declares that the changing of the fractional derivative parameter values' in their domain alters the style of the attained solution in a symmetrical meaning and fully coinciding to the ordinary derivative value'. From these simulations, the results report that the recommended novel algorithm is a straightforward, accurate, and superb tool to generate analytic-approximate solutions for Integral, and integro-differental equations of fractional order.

Aim: this scoping review was designed to identify studies that assess the adverse drug reactions (ADRs) for older people in Australian aged-care facilities. This review critically evaluated each published study to identify the risk of, or actual adverse drug events in older people. Inclusion criteria: This review considered any clinical studies that examined the adverse effects of medications in older people who were living in aged-care facilities. This review considered qualitative studies, analytical studies, RCTs, descriptive cross-sectional studies, and analytic observational studies that explored the use of medications and their adverse effects on older people in clinical settings (including aged care facilities). Methods: An initial search of the PubMed, OvidSP, EBSCOHost, MEDLINE, ScienceDirect, Wiley Online, SAGE, and SCOPUS databases, with full text was performed, followed by an analysis of the article’s title and abstract. Additionally, MeSH was used to describe the article. The initial round of the database search was based on inclusion criteria from studies that assessed tools or protocols aiming to identify the adverse effects of medications on the elderly population suffering chronic conditions or multiple co-morbidities. Two reviewers screened the retrieved papers for inclusion. The data presented in this review are in tabular forms and a narrative summary which aligns with the review’s objectives. Results: Seven studies were identified, and the extracted data from these studies were grouped according their characteristics and the auditing results of each study. Conclusion: There was no comprehensive or broadly adverse drug reaction assessment tool derived from Australian data that has been used on the elderly in an Australian healthcare setting.

According to many researchers, Abstraction is the basis of mathematics, computing, counting devices, and computer science and engineering. What is more, all of the above deal with complexity management in some way, and abstraction is the most basic mechanism of complexity management.Generative software development - whether in the sense of empowering humans by machine to create software or in the sense of reusing products - has been and is one of the serious concerns and goals of software engineering. The interesting thing is that in both views of generativity, the main issue is still, in a way, complexity management: whether this complexity management is to achieve diversity and reuse management (Czarnecki’s approach) or to Structuring from existing structures (the approach of Alexander and his followers in an object-oriented society).In this article, we will first look at complexity and its various definitions. The definitions that show, despite the different perspectives on complexity in different disciplines and domains, all point in one direction. We will conclude that complexity is rooted in multiplicity. In the following, we will formally define complexity. In the following discussion, we will look at the generative patterns of software development, and then we will look at the complexity management patterns at seven levels.In this article, the author has tried to maintain a comprehensive approach to complexity and to consider the approaches of different domains to complexity.

The novel Ionized Gas Thermoelectric Generator (IG-TEG) system that has been studied theoretically showing capabilities to continually extracting energy from the thermal energy of the ambient air, at low temperatures within the standard room temperature and below. This system does not need a temperature gradient in order to work, unlike the other TEGs that use Seebeck effect, and therefore this new system can be utilized for cooling purposes, by extracting energy instead of wasting energy in compressing the gas for cooling. This novel system was designed based on Static Ratchet Potential (SRP), which is known as a spatially asymmetric electric potential produced by an array of positive and negative electrodes. The ratchet potential produces electrical current from random Brownian Motion of charged particles that are driven by thermal energy. Ratchet potential was studied and investigated by several researches in the fields of sensing and energy harvesting. The main ratchet potential system parameter is the particles transportation, this parameter was studied under the condition of flashing ratchet potentials, and was analyzed based on several methods. In this study, a different approach is pursued to estimate particles transportation, by evaluating the charged particles distribution, and applying the other conditions of the SRP.

One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

Respiratory syncytial virus (RSV) is a leading cause of acute lower respiratory infections in young children worldwide. RSV-associated deaths in children are underreported in Bangladesh. We analyzed hospital-based surveillance data on severe acute respiratory infections (SARI) in under-five children before (August 2009–February 2020) and during the COVID-19 pandemic (March 2020–March 2022). Using the World Health Organization definition, we identified SARI cases in 14 tertiary-level hospitals. Nasopharyngeal and oropharyngeal swabs were collected for real-time reverse transcriptase-polymerase chain reaction (rRT-PCR) testing of six respiratory viruses, including RSV. SARI deaths during the pandemic (2.6%, 66) were higher than pre-pandemic (1.8%, 159; p<0.001). Nearly half of pandemic deaths (47%) had underlying respiratory viruses, similar to the pre-pandemic rate (45%). RSV detection in deaths was consistent pre-pandemic (13%, 20/159) and during the pandemic (12%, 8/66). Children aged <6 months constituted 57% (16) of RSV-related deaths. Evaluating interventions like maternal vaccination and infant monoclonal antibody prophylaxis is crucial to address RSV, a major contributor to under-five SARI deaths.

This research aims to find out whether the synthetic 1, 2, 4-triazine and its derivatives have antifungal effects and can protect humans from infection with Candida albicans. Molecular docking and molecular dynamic simulation are widely used in modern drug design to target a We are interested in using molecular docking and molecular dynamics modelling to investigate the interaction between the derivatives of 1, 2, 4-triazine and the resulting lanosterol 14 - demethylase (CYP51) of Candida albicans The inhibition of Candida albicans CYP51 is the main goal of our research. The 1, 2, 4-triazine and its derivatives have been docked to the CYP51 enzyme, which is involved in Candida albicans Multidrug Drug Resistance (MDR). Autodock tools were used to identifying the binding affinities of molecules against the target proteins. Compared to conventional fluconazole, the molecular docking results indicated that each drug has a high binding affinity for CYP51 proteins and forms unbound interactions and hydrogen bonds with their active residues and surrounding allosteric residues. The docking contacts were made using a 10 ns MD simulation with nine molecules. RMSD, RMSF, hydrogen bonds, and the Rg all confirm these conclusions. In addition, these compounds were expected to have a favorable pharmacological profile and low toxicity. The compounds are being offered as scaffolds for the development of new antifungal drugs and as candidates for future in vitro testing.

Coarse-grained molecular dynamics simulations are employed to investigate the spatiotemporal evolution of vesicles (polymersomes) by the self-assembly of randomly distributed amphiphilic BAB triblock copolymers with hydrophilic A and hydrophobic B blocks in an aqueous solution. The vesiculation pathway consists of several intermediate structures, such as an interconnected network of copolymer aggregates, a cage of cylindrical micelles and a lamellar cage. The cage-to-vesicle transition occurs at a constant aggregation number and practically eliminates the hydrophobic interfacial area between the B block and solvent. Molecular reorganization under-lying the sequence of morphology transitions from a cage-like aggregate to a vesicle is nearly isentropic. The end-to-end distances of isolated copolymer chains in solution and those within a vesicular assembly follow log normal probability distributions. This is attributed to the pre-ponderance of folded chain configurations in which the two hydrophobic end groups of a given chain stay close to each other. However, the probability distribution of end-to-end distances is broader for chains within the vesicle as compared to that of a single chain. This is due to the swelling of the folded configurations within the hydrophobic bilayer. Increasing the hydropho-bicity of the B block reduces the vesiculation time without qualitatively altering the self-assembly pathway.

Most of the municipalities in the Gulf region are facing performance related issues in their municipal solid waste management (MSWM) systems. They lack to possess a deliberate inter-municipality benchmarking processes. Instead of identifying the performance gaps for their key components (e.g., personnel productivity, operational reliability, etc.) and adopt proactive measures, the municipalities primarily rely on an efficient emergency response. A novel hierarchical modeling framework, based on deductive reasoning, is developed for performance assessment of MSWM systems. Fuzzy rule based modeling using Simulink-MATLAB was used for performance inferencing at different levels, i.e., component, sub-components, etc. The model is capable of handling the inherent uncertainties due to limited data and imprecise knowledge base. The model’s outcomes can exclusively assist the managers working at different levels of organizational hierarchy for effective decision-making. Performance of the key component, assists the senior management to assess the overall compliance level of performance objectives. Subsequently, operation management can hone in the sub-components to acquire useful information for intra-municipality performance management. While, individual indicators are useful for inter-municipality benchmarking. The model has been implemented on two municipalities operating in Qassim Region, Saudi Arabia. The results demonstrate the model’s pragmatism for continuous performance improvement of MSWM systems in the country and elsewhere.

The growing concerns about floods have highlighted the need for accurate and detailed precipitation data as extreme precipitation occurrences can lead to catastrophic floods, resulting in significant economic losses and casualties. Integrated Multi-satellitE Retrievals for the Global Precipitation Measurement (GPM-IMERG) is a commonly used high-resolution gridded precipitation dataset and is recognized as trustworthy alternative sources of precipitation data. The aim of this study is to comprehensively evaluate the performance of GPM IMERG Early (IMERG-E), Late (IMERG-L), and Run Final (IMERG-F) in precipitation estimation and their capability in detecting extreme rainfall indices over southwestern Iran during 2001-2020. The Asfezari gridded precipitation data which are developed using a dense of ground-based observation were utilized as the reference dataset. The findings indicate that the IMERG-F performs reasonably well in capturing many extreme precipitation events (defined by various indices). All the three products showed a better performance in capturing fixed and non-threshold precipitation indices across the study region. The findings also revealed that both IMERG-E and IMERG-L have problems in rainfall estimation over elevated areas showing values of overestimations. Examining the effect of land cover type on the accuracy of the precipitation products suggest that both IMERG-E and IMERG-L show large and highly unrealistic overestimations over inland water bodies and permanent wetlands. The results of the current study highlight the potential of IMERG-F as a valuable source of data for precipitation monitoring in the region.

The present era of the Internet of Things (IoT) having intelligent functionalities in solving problems pertaining to realtime mission-critical systems has brought an immense revolution in diverse fields including healthcare and navigation systems. However, to the best of our knowledge, the potential of IoT has not been fully exploited yet in the field of the energy sector. We argue that there is an immense need to shift the traditional mission-critical electric power system architecture to IoT-based fully orchestrated architecture in order to increase efficiency, as billions of investment is reserved for the energy sector globally. Since network orchestration deals with auomating the interaction between multiple components involved to execute a particular service, therefore, scheduling the relevant processes within strict deadlines becomes the core pillar of the architecture. The mission-critical systems with urgent task execution often suffer from issues of missing task deadlines. In this study, we present a novel IoT task orchestration architecture for efficient energy management of a nanogrid system that focuses on minimizing the use of nonrenewable energy resources and maximizing the use of renewable energy resources. Moreover, major components of IoT task orchestration such as task mapping and task scheduling are also enhanced using NLP and PSO optimization modules. The proposed task scheduling algorithm incorporates the optimized surplus time, and efficiently executes the energy management-related tasks contemplating to their types. The study utilizes sensors to obtain data from physical IoT devices, including photovoltaic (PV), Energy Storage System (ESS), and diesel generator (DG). The performance of the proposed model is evaluated using data set of nanogrid houses. The outcomes revealed that IoT-task orchestration has played a pivotal role in efficient energy management for nanogrid mission-critical system. Furthermore, the comparison with state-of-the-art scheduling algorithms showed that the task starvation rate is reduced to 16% and 12% when compared with RR and FEF algorithms, respectively.

The Chiltan Formation is a potential hydrocarbon-producing reservoir in the Indus Basin, Pakistan. However, its diagenetic alterations and heterogeneous behavior lead to significant challenges in accurately characterizing the reservoir and production performance. This manuscript aims to utilize Chiltan Limestone core samples to conduct a detailed analysis of the diagenetic impacts on reservoir quality. The formation evaluation was carried out through thin section analysis, SEM-EDS and FTIR investigation, as well as plug porosity and permeability measurements under different stress conditions. In results, Petrography revealed three microfacies with distinct diagenetic features and micro-nano fossil assemblages, including intraclasts, pelloids, bioclasts, and stylolites. Diagenesis has a significant impact on petrophysical properties, leading to increased reservoir heterogeneity. The specified depositional environment exposed the alteration of the Chiltan formation during distinct diagenetic phases in marine, meteoric, and burial settings. Pore morphology and mineralogy reveals complex micro-pore structure with various carbonate mineral phases and cement types in the formation samples. The average porosity and permeability of the core samples were found to be 3.4% and 0.449 mD respectively, indicating poor reservoir quality. Stress sensitivity was determined using Klinkenberg corrected permeability, which indicated a reduction in measured and absolute permeability due to increasing confining stress, further reducing the pore throat structure of the formation. In conclusion, the Chiltan formation possesses intricate reservoir heterogeneity and varied micro-pore structure caused by diagenesis and depositional settings. The formation is classified as a low-quality reservoir due to its non-uniform pore geometry, which exhibits low petrophysical properties resulting from overburden stress. The results of this study provide solid foundation in reservoir characterization and quality assessment which has implications for exploring and exploitation of indigenous resources.

This research project focuses on the optimization of the hybrid energy system together with the assistance of thin-film coatings aiming to achieve self-sustainable food and crop storage facilities which will run effectively with its own generated energy. An infrastructure will be designed and constructed that will comprise a hybrid power generation system accompanied by thin-film coated semitransparent and non-transparent construction materials for energy saving. Thin-film low emissivity (Low-E) type coatings will assist the transparent or semitransparent construction materials to reflect most of the infrared (IR-mostly heat) and UV spectra of sunlight without interrupting the visible spectrum and will lead to saving energy consumption by reducing the heat and lighting during day time

Astola Island is the first marine protected area of Pakistan acknowledged 2017, June 15. It is a rich biodiversity hotspot, Ramsar site inhabiting endangered species like Green turtle, Hawksbill turtle, and Arabian Humpback whale. A saw-scaled Russell’s viper is endemic to Island. Marine ecology of Astola Island is affected by plastic pollution resulting in coral destruction, ocean acidification, global warming, fishing nets blockage, water pollution, and coastal erosion. Zeolite catalyst synthesized from environmentally friendly way by coal fly ash to degrade collected plastic waste from Island into useful products in pyrolysis reactor. The synthesized catalyst functionalized further with three type of organosilane(1) Octyltriethoxysilane(OS),(2)Phenyltriethoxysilane(PS)(3)Vinyltriethoxysilane(VS).Zeolite functionalize with octyltriethoxy silane (ZO) shows the highest performance in plastic pyrolysis, resulting in lower degradation temperature, low residue and more product formation may be due to having long chain hydrocarbon and acidic sites. Plastic recycling is the promising solution to tackle plastic blooming issue. Which is negatively impacting all the compartments of ecosystem especially marine environment.

COVID-19 is a severe global problem, and AI can play a significant role in preventing losses by monitoring and detecting infected persons in early-stage. This paper aims to propose a high-speed and accurate fully-automated method to detect COVID-19 from the patient's CT scan images. We introduce a new dataset that contains 48260 CT scan images from 282 normal persons and 15589 images from 95 patients with COVID-19 infections. At the first stage, this system runs our proposed image processing algorithm to discard those CT images that inside the lung is not properly visible in them. This action helps to reduce the processing time and false detections. At the next stage, we introduce a novel method for increasing the classification accuracy of convolutional networks. We implemented our method using the ResNet50V2 network and a modified feature pyramid network alongside our designed architecture for classifying the selected CT images into COVID-19 or normal with higher accuracy than other models. After running these two phases, the system determines the condition of the patient using a selected threshold. We are the first to evaluate our system in two different ways. In the single image classification stage, our model achieved 98.49% accuracy on more than 7996 test images. At the patient identification phase, the system correctly identified almost 234 of 245 patients with high speed. We also investigate the classified images with the Grad-CAM algorithm to indicate the area of infections in images and evaluate our model classification correctness.

Water scarcity challenges have necessitated the adoption of water-saving techniques in protected and nom-protected farming. This study aimed to assess the performance of a water-saving soil-less cultivation technique and to compare it with conventional soil-based cultivation in protected farming. The soilless technique used local gravel and a mixture of peat-moss, humin-substrate, and perlite in ratios of 4:3:1.5. Three irrigation regimes were imposed using emitters 8Lh-1 design discharge (D1) emitters with 6Lh-1 design discharge (D0.75) and 4Lh-1 de-sign discharge (D0.5) for the two cultivation methods during the growth cycle of tomato by drip irrigation. The vegetative growth, fruit yield and water consumption were measured and water productivity was determined. Moreover, an economic assessment was carried out by estimating and comparing economic coefficients for the two cultivation methods. Estimated coefficients include revenues, net profit, benefit-cost ratio, break-even levels of production and prices, revenues over variable cost, and revenues on investment. The tomato fruit yield under soil-based cultivation overtopped the yield under soilless cultivation. The water productivity under the soilless cultivation was almost twice that (24.3 kg m-3) of the soil-based cultivation (15.5 kg m-3). The soilless cultivation saved 50% of irrigation water applied by the conventional soil-based method, saving energy and soil from deterioration. Revenues and net profits stimulated by higher yield coupled with lower variable cos supported the soil-based cultivation. The economic assessment showed that both cultivation methods were economically viable. However, the soil-based cultivation method was more profitable due to its higher fruit yield. Overall, the results of this study suggest that the soilless cultivation technique is a viable option for wa-ter-saving cultivation. However, the soil-based cultivation method is still more profitable due to its higher fruit yield

The growing importance of edge and fog computing in the modern IT infrastructure is driven by the rise of decentralized applications. However, resource allocation within these frameworks is challenging due to varying device capabilities and dynamic network conditions. Conventional approaches often result in poor resource use and slowed advancements. This study presents a novel strategy for enhancing resource allocation in edge and fog computing by integrating machine learning with blockchain for reliable trust management. Our proposed framework, called CyberGuard, leverages blockchain’s inherent immutability and decentralization to establish a trustworthy and transparent network for monitoring and verifying edge and fog computing transactions. CyberGuard combines the Trust2Vec model with conventional machine learning models like SVM, KNN, and Random Forests, creating a robust mechanism for assessing trust and security risks. Through detailed optimization and case studies, CyberGuard demonstrates significant improvements in resource allocation efficiency and overall system performance in real-world scenarios. Our results highlight CyberGuard’s effectiveness, evidenced by a remarkable accuracy, precision, recall, and F1-Score of 98.18%, showcasing the transformative potential of our comprehensive approach in edge and fog computing environments.

The speed-density or flow-density relationship is a fundamental aspect of traffic flow theory. Single-regime models often face challenges in consistently fitting empirical data under diverse traffic conditions. This paper addresses the inaccuracies of single-regime models, attributing them not only to their functional forms but also to data dispersion and sample selection bias. To mitigate these issues, the data is segmented into day and night periods, leading to the creation of separate models for each. Calibration results, conducted on data from two freeways, Tehran-Karaj and Tehran-Qom, reveal distinct challenges, with the former exhibiting high dispersion and the latter showing low dispersion. Surprisingly, single-regime models demonstrate notable effectiveness when applied to distinct day and night data. Further analysis, categorizing data into day and night, results in reduced errors (20-60% improvement in R-Square), emphasizing the potential for enhanced accuracy by considering distinct regimes. Overall, the study underscores the significance of regime-specific considerations for accurate traffic flow modeling. Upon thorough evaluation, the study highlights the superiority of the neural network Multi-layer Perceptron (MLP) over traditional models. The research discusses the implications of incorporating day and night parameters into the models, emphasizing their potential for accuracy enhancement.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

Nowadays, one of the biggest concern of human being is greenhouse gas emission, especially carbon dioxide emission in developed and under-developing countries. In this study, connectionist models including LSSVM (Least Square Support Vector Machine) and evolutionary methods are employed for predicting the amount of CO₂ emission in six Latin American countries, i.e., Brazil, Mexico, Argentina, Peru, Chile, Venezuela, and Uruguay. The studied region is modelled based on the available input data in terms of Million tons including oil (Million tons), gas (Million tons oil equivalent), coal (Million tons oil equivalent), $R_{ew}$ (Million tons oil equivalent), and Gross Domestic Product (GDP) in terms of billion US dollars.} Moreover, the available patents in the fields of climate change mitigation in six Latin American countries namely Brazil, Mexico, Argentina, Peru, Chile, Venezuela, and Uruguay has been reviewed and analyzed. The results show that except Venezuela, all other mentioned countries have invested in renewable energy R&D activities. Brazil and Argentina have the highest share of renewable energies which account for 60% and 72% respectively.

This study investigates how students' well-being relates to sustainable development and education for sustainability at Prince Mohammad Bin Fahd University, Saudi Arabia. The authors endeavor to answer the question "How Does Students' Well-Being Relate to Sustainable Development Via Education for Sustainable Development?" and four sub-questions. Primary data were collected by semi-structured interviews exploring the viewpoints of twenty female and male students (n=26) aged between 18 and 26. The content analysis results have identified additional well-being and education for sustainability factors that influence sustainable education and, therefore, sustainable development. These antecedents include workload, transparency, grading criteria, fairness, belonging, work-life balance, mental health support, missing emotional intelligence factors, factors related to Education for Sustainable Development, such as instructors' role models, institutional commitment, leadership, and collaboration with government. In addition, the study developed a theoretical model for the relationship between antecedents for Education for Sustainable Development, Education for Sustainable Development, and Sustainable Development in the Saudi context. Finally, the study answers four research questions: What factors contribute to education for sustainable development? What are the antecedents of education for sustainable development? How do university educators contribute to sustainable education? How do the antecedents of education for sustainable development, education for sustainable development, and sustainable development relate?

Structural design optimization (SDO) plays a pivotal role in enhancing various aspects of construction projects, including design quality, cost-efficiency, safety, and structural reliability. Recent endeavors in academia and industry have sought to harness the potential of Building Information Modeling (BIM) and optimization algorithms to optimize SDO and improve design outcomes. This review paper aims to synthesize these efforts, shedding light on how SDO contributes to project coordination. Furthermore, the integration of sustainability considerations and the application of innovative technologies and optimization algorithms in SDO necessitate more interactive early-stage collaboration among project stakeholders. This study offers a comprehensive exploration of contemporary research in integrated SDO employing BIM and optimization algorithms. It commences with an exploratory investigation, employing both qualitative and quantitative analysis techniques following the PRISMA systematic review methodology. Subsequently, an open-ended opinion survey was conducted among construction industry professionals in Europe. This survey yields valuable insights into the coordination challenges and potential solutions arising from technological shifts and interoperability concerns associated with widespread SDO implementation. These preliminary steps of systematic review and industry survey furnish a robust knowledge foundation, enabling the proposal of an intelligent framework for automating early-stage sustainable structural design optimization (ESSDO) within the construction sector. The framework ESSDO addresses the challenges of fragmented collaboration between architects and structural engineers. This proposed framework seamlessly integrates with the BIM platform, i.e., Autodesk Revit for architects. It extracts crucial architectural data and transfers it to the structural design and analysis platform, i.e., Autodesk Robot Structural Analysis (RSA), for structural engineers via the visual programming tool Dynamo. Once the optimization occurs, optimal outcomes are visualized within BIM environments. This visualization elevates interactive collaborations between architects and engineers, facilitating automation throughout the workflow and smoother information exchange.

Considering the significant advancements in autonomous vehicle technology, research in this field is of interest to researchers. To automatic parking, controlling steer angle, gas hatch, and brakes need to be learned. Due to the increase in the number of cars and road traffic, car parking space has decreased. Its main reason is information error. Because the driver does not receive the necessary information or receives it too late, he cannot take appropriate action against it. This paper uses two phases: the first phase, for goal coordination, was used genetic algorithms and the Cuckoo search algorithm was used to increase driver information from the surroundings. Using the Cuckoo search algorithm and considering the limitations, it increases the driver’s level of information from the environment. Also, by exchanging information through the application, it enables the information to reach the driver much more quickly and the driver reacts appropriately at the right time. The suggested protocol is called the MODM-based solution. Here, the technique is assessed through extensive simulations performed in the NS-3 environment. Based on the simulation outcomes, it is indicated that the parking system performance metrics are enhanced based on the detection rate, false-negative rate, and false-positive rate.

The comfort of human life depends on the quality, size, and reliability of the infrastructure projects. In the infrastructure systems, rapid growth is found, where the economic and sustainable impact has become a topic of significant concern for policies and government officials. To achieve con-straints of sustainable development, all the policies and actions over the infrastructure project's life cycle must be assessed. Decision-makers have adopted approaches for economic, social, and en-vironmental initiatives through Life Cycle Assessment (LCA) and Life Cycle Cost Analyses (LCCA) of infrastructure projects. The purpose of this review is to highlight the impact of per-forming LCA and LCCA in infrastructure projects. To achieve this goal, a systematic literature review methodology is adopted in which renowned databases, i.e., Web of Science, Science Direct, Emerald and Scopus were selected to extract the relevant literature. Using the PRISMA approach, 1251 publications were identified which were then filtered and 55 documents were included in the final review. In the extracted publications most, researchers were biased toward LCA and LCA individually, whereas few focused on integrated LCA and LCCA. The researchers assessed the costs and impact associated with the infrastructure project while there were less focused on the environmental cost. Besides this, techniques of economic, social, and environmental growth of infrastructure projects have been emphasized during the design phase because of substantial relations between infrastructure design and operation management. Moreover, a conceptual framework has been developed that will assist the decision-makers to consider the effects of LCA and LCCA on various aspects of the infrastructure project and how it impacts sustainability. In the last, a case study was performed to assess the developed framework with the incorporation of environmental impact cost.

High dimensional datasets are highly likely to have redundant, irrelevant, and noisy features that negatively affect the performance of the classification algorithms. Selecting the most relevant features and reducing the dimensions of datasets by removing the undesired features is a dimensional reduction technique called Feature Selection (FS). In this paper, we propose an FS approach based on the Black Hole Algorithms (BHO) with a mutation technique called MBHO. Generally, BHO contains two major phases. At the exploitation phase, a set of stars are modified based on some rule and according to some objective function, the best star is selected as the black hole which attracts other stars. Furthermore, when a star gets closer to the event horizon, it will be swallowed and a new one will be randomly generated in the search space which thus is the exploration phase. However, randomness may cause the algorithm to fall into the trap of local optima, and to overcome such complications, inversion mutation is used. Furthermore, we modify a widely utilized objective function in most of the proposed works for wrapper feature selection by combining two new terms that are based on the correlation among the selected subset of features and the features and the classification label. We also utilize a transfer function, known as the V2 transfer function, to convert continuous values into discrete ones to enhance search. We assess our approach via extensive evaluation experiments using fourteen benchmark datasets. We benchmark the performance of a wrapper FS approach called Binary Cuckoo Search (BCS), and three filter-based FS approaches (namely Mutual Information Maximisation (MIM), Joint Mutual Information (JMI), and minimum Redundancy Maximum Relevance (mRMR)). Our evaluation has shown that the proposed model is an effective approach for FS, in selecting better features that enhance the performance metrics on the classifiers. Thus, MBHO can be utilized as one alternative to the existing state-of-art-approaches. We release the source codes of our implementation for the community to build on with new methods and datasets.