Extensive research has been conducted on printable antenna technologies, believed to be fast-growing due to their significant impact on wireless devices. It is necessary to study the progress of printable antenna technology as they are core devices for wireless technology today. This review work offers a comprehensive account of the previous and recent research achievements based on the principle of printable antenna, and parametric studies of several key design parameters, for future wireless network applications. The systems considered for evaluation include broadband techniques, large Bandwidth, high gain, dual/multi-band, or reconfigurable structure, low-profile, size-reduction, compact, linear, or circular polarization applications. It also highlights the fabrication procedures, and the numerous material characteristics affecting the antenna performance for various wireless applications with design considerations. Fully printed antennas on different substrates and conductive ink were investigated, including polyethylene terephthalate (PET), synthetic paper (Teslin), resin-coated photo paper, and Kapton polyimide substrates, among many others. The findings show that the fully inkjet-printed antenna made fabrication easy, improving the accuracy and conductivity of the printed patterns by concentrating on the inherently difficult problems and opportunities. Inkjet-printed antennas are believed to be the futuristic demand for sustainability and wireless solution in several ways.

A sustainable, scalable source of energy‐dense chemical fuel is urgently needed to ensure the security of our energy supply for future generations. Solar energy is the only renewable energy source of sufficient scale to replace fossil fuels and meet rising environmental demand. Hydrogen is expected to play a key role as an energy carrier in future energy systems of the world. As fossil fuel supplies become scarcer and environmental concerns increase, hydrogen is likely to become an increasingly important chemical energy carrier and eventually may become the principal chemical energy carrier. When most of the world’s energy sources become non-fossil based, hydrogen and electricity are expected to be the two dominant energy carriers for the provision of end-use services. Photocatalytic hydrogen evolution from water by solar energy over semiconductors offers a promising way for clean and renewable production of hydrogen. The TiO2-based materials have received considerable attention in recent years due to their extensive application in photocatalysis for hydrogen evolution. Though TiO2 is the most widely investigated photocatalyst for hydrogen evolution, it still provides low photocatalytic activity due to the wide bandgap that results in photocatalytic activity only under ultraviolet (UV) irradiation. Modification of TiO2 photocatalysts with several transition metals has been extensively studied to extend the absorbance capacity of TiO2 into the visible range. The effect of different photocatalytic deposition and reaction parameters also play major roles in enhancing the photostability of photoanode and increasing the hydrogen gas output, respectively.

Enzymatic degradation of organic pollutants is a new and promising remediation approach. Peroxidases are one of the most commonly used classes of enzymes to degrade organic pollutants. However, it is generally assumed that all peroxidases behave similarly and produce similar degradation products. In this study, we conducted detailed studies of the degradation of a model aromatic pollutant, Sulforhodamine B dye (SRB dye), using two peroxidases—soybean peroxidase (SBP) and chloroperoxidase (CPO). Our results show that these two related enzymes had different optimum conditions (pH, temperature, H₂O₂ concentration...etc.) for efficiently degrading SRB dye. High-performance liquid chromatography and LC-mass spectrometry analyses confirmed that both SBP and CPO transformed the SRB dye into low molecular weight intermediates. While most of the intermediates produced by the two enzymes were the same, the CPO treatment produced at least one different intermediate. Furthermore, toxicological evaluation using lettuce (Lactuca sativa) seeds demonstrated that the SBP-based treatment was able to eliminate the phytotoxicity of SRB dye, but the CPO-based treatment did not. Our results show, for the first time, that while both of these related enzymes can be used to efficiently degrade organic pollutants, they have different optimum reaction conditions and may not be equally efficient in detoxification of organic pollutants.

Energy harvesting is an emerging topic recently. This harvested energy is used to operate wireless sensors for different industrial monitoring and automation. To maximize the harvested energy in spinning systems, the harvester should vibrate at resonance for different spinning frequencies which can be achieved by active fitting. In this research, a novel methodology was developed by actively customizing the length of vibrating element beam to manipulate its natural frequency according to the spinning frequency. Different models were investigated numerically and experimentally to verify the proposed methodology. COMSOL Multiphysics software V5.1 was used to develop the numerical model, then and tip deformation and voltage difference results were benchmarked. The numerical model was verified experimentally by attaching a piezoelectric MIDE PPA 1021 which its vibrating length was varied by changing the supporting length from 0 mm to 12 mm to a spinning object having variable frequency from 0-200 Hz. It is found that the MIDE PPA 1021 beam vibrated at its resonance throughout the specified spinning frequencies. The proposed harvester can be applied in battery-free sensors being used in automotives, wind-mills blades, and rotating machinery.

This research answers the knowledge gap regarding the explanation of the quantum jump of the electron. This scientific paper aims to complete Einstein's research regarding general relativity and attempt to link general relativity to quantum laws.

Leadership performance by village leaders is essential to promote sustainable life among rural communities, especially fisheries community who living along coastal villages. Otherwise, previous studies found that performance issues among village’s leaders remain as serious problems, and need to find the best solution. This study was conducted to profile the job performance among village leaders based on demographic factors such as educational level, age and experiences as village leader. The data of this cross-sectional survey were collected by questionnaires on 300 respondents consist of members of village organization through stratified sampling’s technique, while the data was analysed by SPSS using items of mean, standard deviation, independent-sample t-test and anova. The finding shown that there were differences in job performance among village leaders on educational level, age and experiences. Interestingly, the finding told the best on job performance among village leaders are (i) the age between 41 to 50 years old; (iii) the experience between 11 to 20 years; and (iii) the higher educational level the higher job performance among them. This result can be using by government or any responsible parties to improve job performance among village leaders, especially for recruitment selection and for in-service training.

This paper presents a concise mathematical framework for investigating both feed-forward and backward process, during the training to learn model weights, of an artificial neural network (ANN). Inspired from the idea of the two-step rule for backpropagation, we define a notion of F_adjoint which is aimed at a better description of the backpropagation algorithm. In particular, by introducing the notions of F-propagation and F-adjoint through a deep neural network architecture, the backpropagation associated to a cost/loss function is proven to be completely characterized by the F-adjoint of the corresponding F-propagation relatively to the partial derivative, with respect to the inputs, of the cost function.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

Brain plasticity is the ability of the brain to change and adapt in response to experience or learning. Its hallmarks are developmental flexibility, complex interactions of genetic and environmental influences, and structure-functional changes comprising neurogenesis, axonal sprouting, and synaptic remodeling. Herein, we review brain plasticity association with non-coding RNAs (ncRNAs). Studies on brain plasticity have important practical implications. Numerous cerebral ncRNAs are linked with neurological disorders, which makes them putative targets for RNA-based diagnostics and therapeutics since molecular characteristics of brain plastic change may reveal disease course and rehabilitative potential of the patient. A new insight into the concept of brain plasticity will provide perspectives on functional recovery following brain damage. The knowledge of this phenomenon will enable physicians to exploit cerebral plastic potential and regulate eloquent networks with timely interventions. Future studies will provide pathophysiologic mechanisms of brain plasticity at macro- and microscopic levels to advance rehabilitation strategies and improve the quality of life in neurological disorders.

Severe early childhood caries remains the most common chronic disease affecting children. Its multifactorial etiology has established a controversy about which risk factors were more significant to its development. Therefore our study aimed through meticulous statistical analysis to arrange the “well agreed upon” common risk factors in order of significance, to aid the clinician in tailoring an adequate preventive program for this affected age group. The study reshuffled the risk factors contributing to severe early childhood caries and placed them in the order of their significance as follows: snacking of sugary food several times a day, increased number of siblings to 3 or more, night feeding, child self-employed brushing, mother caries experience, 2 siblings, on demand feeding, once/day sugary food, sharing utensils, 1 Sibling, male gender, father’s education, late first child dental visit, brushing time, mother’s education, no dental visit, decreased brushing frequency & no night brushing.

Coating of suitable materials having thickness of few atoms to several microns on a substrate is of great interest to the scientific community. Hard coatings develop under the significant composition of suitable-natured atoms where their force-energy behaviors when in certain transition state favour binding. In the binding mechanism of suitable atoms, electron belonging to outer ring filled state of gas-atom undertakes another clamp of energy knot belonging to outer ring unfilled state of solid-atom. Set process conditions develop the binding of different-natured atoms when processing their suitable composition in a system. Atoms of different nature develop structure in the form of hard coating by locating their ground points between the original ones. Here, gas-natured atoms increase the potential energy under decreasing levitational force of electrons, whereas, solid-natured atoms decrease the potential energy under decreasing gravitational force of electrons. In TiN coating, Ti–Ti atoms bind under the difference of expansion of their lattices, called nets of energy knots, where one atom just lands on the already landed atom. An adhered N-atom to a Ti-atom forms its position among four Ti-atoms where N-atom occupies the interstitial site of Ti-atoms. Two oppositely working force-energy behavior atoms deposit in the form of coating at substrate surface as per set conditions of the process. The rate of ejecting (or dissociating) solid-natured atoms depend on the nature of their source (target), process parameters and processing technique. In random arc-based vapor deposition system, depositing differently natured atoms at substrate surface depends on the input power. In addition to intrinsic nature of atoms, different properties and characteristics of coatings emerge as per engaged forces under their involved energy. The present study sets new trends in the field of coatings involving the diversified class of materials and their counterparts.

It has been proven that in standard Einstein gravity, exotic matter (i.e. matter violating the point-wise and averaged weak and null energy conditions) is required to stabilize traversable wormholes. Quantum field theory permits these violations due to the quantum coherent effects found in any quantum field . Even reasonable classical scalar fields violate the energy conditions. In the case of the Casimir effect and squeezed vacuum states, these violations have been experimentally proven. It is advantageous to investigate methods of minimizing the use of exotic matter. One such area of interest is extended theories of Einstein gravity. It has been claimed that in some extended theories, stable traversable wormholes solutions can be found without the use of exotic matter. There are many extended theories of gravity and in this review paper we first explore f(R) theories and then explore some wormhole solutions in f(R) theories including Lovelock gravity.

: Digital communication is becoming an integral component of contemporary society and the use of mobile devices is increasing faster than ever. The function of message communication is becoming more popular as for mobile phone users, a short messaging service (SMS) requires an extremely high level of security. Any SMS that enters a person's smartphone must be considered a private affair, with privacy and security safeguarded. This research study found a novel Deoxyribonucleic acid (DNA) Cryptography method that uses a dynamic DNA sequence table to increase security. Cryptography is a popular approach for ensuring the confidentiality of a message. This paper proposed an Efficient Cryptographic Scheme for SMS (ECSS) algorithm to protect texts received from an Android smartphone. ECSS-based encryption has been identified as a novel method of securing information in the form of DNA molecules that employ DNA strands to conceal the information. This Paper provides the DNA cryptography approach for encrypting and decrypting plain texts in this work. The primary goal of ECSS cryptography is to guarantee secrecy when people transfer data across a network. This paper examines DNA Crypto, the distinction between classical cryptography and DNA Data encryption. An Android-based app is created to perform the proposed technique and the results show that the algorithms produce a consistent encryption result in which the length of the message before encryption is always the same as the length of the message after decryption. The suggested security solution has the potential to greatly improve the security of mobile communication. This Paper also provides experimental results for our chat application performance, such as received text message correctness, cipher text, average encryption time and average decryption time. According to the findings/results of this study, the speed of average encryption and decryption of the description is roughly 0.011 and 0.037 sec and prevents plaintext and dictionary attacks.

In its 8th Malaysia Plan (MP*), the Malaysian government has given nanotechnology development a high priority and has been made a Strategic Research (SR) programme. Consequently, an exhaustive and long-term approach is essential. Additionally, specific laws are required to provide an optimal health and safety environment for workers. Consequently, the current study intends to assist Malaysian policymakers in promoting improved safety, risk assessment, and management for nanotechnology workplaces, as well as drafting a comprehensive policy for the recently released DOSH guideline in 2018. Utilizing a unique methodology, this study evaluated the assessment and management of nanotechnology health and safety risks in Malaysia using the international risk governance council (IRGC) framework. In addition to document analysis, n = 20 semi-structured interviews were conducted with representatives of several nanotechnology platforms to collect data that was then analyzed thematically. The research evaluated current workplace safety regulations and laws. Consequently, we propose a future dynamic strategy for Malaysian nanotechnology with more favourable upgrades supported by increased concentrations in the following areas: I policy creation, ii) comprehensive management system, iii) knowledge transfer, and iv) infrastructure management. In addition, the findings highlight the need of cross-sectional communication in bridging existing gaps. This study laid the groundwork for a more systematic and comprehensive health and safety strategy.

In this study, the optimal condition for the extraction of antioxidants from the fruit Buah Mahkota Dewa (Phaleria macrocarpa) was determined by using Response Surface Methodology (RSM). The optimization was applied using central composite design (CCD) to investigate the three independent variables, namely extraction temperature (^oC), extraction time (minutes) and extraction solvent to-feed ratio (%v/v) on the responses of free radical scavenging activity (DPPH), ferric ion reducing power assay (FRAP), total phenolic content (TPC) and total flavonoid content (TFC).The optimal conditions for the antioxidants extraction were found to be extraction temperature (64^oC), extraction time (66 minutes) and solvent to-feed ratio (75 %v/v) with the highest percentage yield of DPPH, FRAP, TPC and TFC were 86.85%, 7.47%, 292.86 mg/g and 3.22 mg/g respectively. Moreover, the data were subjected to response surface methodology (RSM) and the results showed that the polynomial equations for all models were significant, did not show lack of fit, and presented adjusted determination coefficients (R²) above 99%, proving the yield of phenolic, flavonoid and antioxidants activities obtained experimentally were close to the predicted values and the suitability of the model employed in RSM to optimize the extraction conditions. Hence, in this study, the fruit from P.macrocarpa could be considered to have the strong antioxidant ability and can be used in various cosmeceutical or medicinal applications.

With global climate change and resource constraints looming large, sustainable design has become a focus of attention for all industries. The purpose of this study was to investigate the attitudes and behavioural intentions of undergraduate fashion design students towards sustainable fashion practices. Undergraduate fashion design students (n = 441) from three universities in Guangdong Province, China, participated in this survey. By constructing different scales of environmental knowledge, attitude towards sustainable fashion practice and behavioural intention towards sustainable fashion practice, and by using structural equation modelling to analyse the relationship between environmental knowledge and sustainable fashion practice, the following conclusions were drawn: (1) environmental knowledge has a positive effect on attitude towards sustainable fashion practice (p＜0.05); (2) environmental knowledge has a positive effect on behavioural intention towards sustainable fashion practice (p＜0.05); (3) Subjective norms has a positive effect on behavioural intention towards sustainable fashion practice (p＜0.05). (4) Attitudes towards sustainable fashion practice play a mediating role in the relationship between environmental knowledge and intentions towards sustainable fashion practice behaviour (p＜0.05). The findings of this study have implications for environmental education for undergraduate fashion design students and for sustainable production in companies.

Structural systems in housing projects contribute to the energy consumption of buildings during and after construction, and the climate plays a significant role in this energy consumption. Housing projects in harsh environments such in the United Arab Emirates (UAE) directly contribute to energy performance, specifically in low-density residential areas. By selecting the most efficient structural system, prior construction can enhance energy performance in such housing projects. The present study investigates the energy performance of three different structural systems used in UAE national housing: precast concrete, reinforced concrete, and light gauge steel (LGS). The case studies used for this study were constructed in Abu Dhabi, the capital of the UAE, specifically in Alain city. Second, through qualitative analysis and average annual billing of each housing project, the study identifies the thermal defects and determines the electricity consumptions of each system. The results indicate that the LGS system provides high thermal conductivity through its structural elements whereas reinforced concrete leads to the highest annual energy consumption in kW h/m². Finally, precast concrete has few thermal defects in its junctions and structural elements. The results indicate that LGS and reinforced concrete should be further studied, especially with regard to insulation and improvement, prior to implementation in housing systems.

Joining of aluminium alloys to steels has been extensively studied, especially in the automotive sector. However, aluminium alloys are known to be difficult to join with steels when methods involving fusion welding are used because of hot cracking problem. Hence, a high strength joint between these dissimilar metals would be of benefit especially in reducing the weight of products. In this work the torch brazing method was applied to join AR500 steel with AA7075 aluminium alloy using Al-Si-Zn base filler metal at various flame times. The effect of the brazing work on the intermetallic phase formation and the mechanical strength of the joints were investigated. In this work, the maximum shear load obtained was 6460 N and the presence of the intermetallic phases had reduced the shear strength of the brazed joints. However, the torch brazing process using Al-Si-Zn filler metal had successfully facilitated the joining of these dissimilar metals.

Election Algorithm (EA) is a powerful metaheuristics model motivated by phenomena of the socio-political mechanism of the presidential election conducted in many countries. EA is selected as a topic of discussion due to its capability and robustness to carry out complex problems in the random-2SAT logic program. This paper utilizes a hybridized EA assimilated with the Hopfield neural network (HNN) in carrying out random logic program (HNN-R2SATEA). The efficiency of the proposed method was compared with the existing traditional exhaustive search (HNN-R2SATES) model and the recently introduced HNN-R2SATICA model. From the result obtained, clearly proven that based on our proposed hybrid model outperformed other existing model based on the Global Minima Ratio (ZM), Mean Absolute Error (MAE), Bayesian Information Criterion (BIC) and Execution Time (ET). The expected outcome portrays that the EA algorithm outperformed the other two algorithms in doing random-kSAT logic program. The results proved the robustness, effectiveness, and compatibility of the HNN-R2SATEA model.

Cricket, the most popular sports in the world to chase by the fans. Many cricket fans are interested in analyzing the elements and activities that affect the outcomes of matches. Machine learning in sports analytics is a relatively new topic in computer science. The purpose of this survey is to anticipate the outcome of a PSL champion team and build a winning strategy. Machine learning (ML) has exhibited favorable outcomes in a variety of sectors for diverse prediction using classification, regression, and so on, and is proven to be accurate. The innovative frameworks based on ML have the ability to learn from previous experiences. The cricket pitch is the most important aspect, alongside home game an edge, coin toss, innings of play, day/night match, physical conditioning, and dynamic plans, among other things. The dataset from previously ESPN Cricifno was used for this purpose. Recent classification approaches including, Random Forest, Gradient Boost, Deep Neural Networks used to conduct a comparative analysis based on their results and performances, as well as team strategies.

Bioconvective flows have attracted attention in recent years due to actual and potential applications. In this paper, we consider a steady and laminar convective MHD flow of a nanofluid with heat, mass and microorganism transfer with a heat source/sink present. In addition, we assume there exists a first order chemical reaction. The governing partial differential equations (PDEs) are reduced to ordinary differential equations (ODEs) using the scaling group transformation and the associated boundary value problem is then solved. The influences of selected governing parameters on the dimensionless velocity, temperature, nanoparticle concentration, density of motile microorganisms, skin friction, heat transfer, mass transfer, and motile microorganism density rates are computed and discussed

Purpose: For businesses of all sizes, turnover is a significant issue that has a detrimental impact on organizational performance. This study investigates the variables influencing SME workers' intentions to leave their current employers. This study also examines the moderating effect of organizational commitment on the relationships between attitude, subjective norms, perceived behavioral control, and turnover intentions. Methodology: Six hypotheses were proposed regarding the connections between the initial TPB components and organizational commitment. Results: The PLS-SEM structural path analysis findings revealed that the three fundamental predictors of TPB significantly influence turnover intention, with perceived behavioral control most strongly influencing intention. Furthermore, the results revealed that organizational commitment moderated the relationship between TPB constructs and turnover intention. Practical Implications and Originality: This study used an extended TPB model to introduce fresh perspectives into the literature on SME workers' organizational commitment.

Differentiated instruction has been implemented in classrooms where students who come from various backgrounds require appropriate lessons that are tailored to their varied learning preferences. As the spread of coronavirus 19 (Covid-19) is becoming more rampant, online learning has been lifted up as the main platform of teaching and learning, forcing the need to shift from the conventional face-to-face classroom to online, or virtual, mode of knowledge transfer. Having such global phenomenon affecting education, how does it affect the implementation of differentiated instruction that has been practised regularly by teachers before the wake of Covid-19? Previous studies have shown how it is done in the normal classroom setting, and that the practice of differentiated instruction contributes to students’ motivation as well as academic performance. However, there is a need to explore how do teachers go about with online differentiated instruction and how does it affect the students, since online learning poses various threads to both teachers and students; and thus, one might argue the effectiveness of not only the teaching approach but also the overall teaching and learning outcomes. Borg’s framework of teacher cognition, which has been extensively used in exploring how teachers teach, can be utilized to document the practice of online differentiated instruction. This study aimed to explore the practice of online differentiated instruction by teachers and examined its impact on students’ motivation and academic performance during the Covid-19 outbreak. The participants of this study consists of 247 gifted students from a public school in Malaysia. To meet these aims, this study employed a mixed method research design, utilizing the framework of teacher cognition to explore the teachers’ practice of online differentiated through interviews; and, utilizing a survey design using a questionnaire to determine the impact of online differentiated instruction towards students’ motivation and academic performance. The findings revealed that although online differentiated instruction is feasible, however, appropriate combination of differentiation constructs need to be applied in order to achieve higher motivation and better academic performance among the students.

Nanofibres have gained increasing attention due to their advantages of having a high porous structure, narrow pore size and distribution, and a high specific surface area. One of the most efficient techniques for producing nanofibres is via electrospinning. Nanofibres are currently being used in various fields, including water filtration. Although nanofibres possess the ability to filter various components, the fibres generally have a low mechanical strength that can mitigate the performance over time. Therefore, in overcoming this issue, several studies have focused on improving the strength of the nanofibre membranes for a water filtration application. This review discusses the advantages and challenges of nanofibres for water filtration membranes and summarises the methods to increase the strength of the membranes, including solvent vapour, thermal treatment, and chemical crosslinking.

Assessment of the trends of land cover and vegetation dynamics (VD) using remote sensing (RS) and indicators such as anthropogenic activities and the socio-demographic information is essential in order to make proper planning for sustainable management. This paper attempts to evaluate land cover change (LCC) and VD in Kebbi State, Nigeria using historical Landsat data from 1986-2016 by means of remote sensing. The Driver-Pressure-State-Impact-Response (DPSIR) framework was later employed using both primary and secondary data for a better understanding of the drivers, the state of the environmental condition, the causes as well as the impact of the change. The images were classified into five thematic land cover classes as Dense Vegetation, shrubs/built area, farmland, bare/grassland and water body by means of Maximum likelihood supervised classification technique in accordance with Anderson classification scheme level 1, with acceptable accuracy. Pre-classification and post-classification change detection (CD) methodologies were executed using Normalized difference vegetation index (NDVI) and Image differencing respectively. The study illustrates a steady decline in dense vegetation and shrubs/build areas while farmland and bare/grassland increases, however, water bodies remain unchanged. The DPSIR pin-point that the major drivers of change in the study area have been the pressing need for farming land as the population grows and socioeconomic demands including fuelwood consumption and endemic poverty. Expansion of Farming land, fuelwood consumption and the need for construction materials are identified as the main key elements exerting pressure for the change. The state of the condition indicates a steady decline in dense vegetation and shrubs areas while farmland and bare/grassland are increasing significantly. The impacts include land degradation, the decline in the provision ecosystem goods and services, biodiversity loss through loss of habitats. The study, however, noted that many international and national policies in response to land degradation are channelled toward land restoration and remediating of the environment, through afforestation programs and improving the livelihood of the rural people through providing alternative income sources since they depend heavily on land for sustenance. However, the state governments, communities and individual commonly organized annual tree planting campaign with the main purpose of environmental protection.

A biofilm is any syntrophic consortium of microorganisms in which cells adhere to one another and, in some cases, to a surface. These adherent cells become encased in a slimy extracellular matrix made up of extracellular polymeric substances (EPSs). Until now, the use of commercial disinfectants remains the main strategy to control biofilm-mediated problems. This mini review summarizes common antibiofilm mode of actions taken by disinfectants and how water channels in microbial biofilms contribute to disinfectant resistance.

Moringa oleifera is a miracle plant with many nutritional and medicinal properties. Chemopreventive value of the combined mixture of moringa leaves and seed residues (MOLSr) at different ratios (M1S9, M1S1 and M9S1) were investigated. MOLSr extracts were subjected to phytochemical screening, antioxidant assays, metabolite profiling and cytotoxic activity on various human cancer cell lines including primary mammary epithelial cells (PMEC). The MOLSr ratio with the most potent antiproliferative activities were used in xenograft mice injected with MDA-MB-231 cell lines for in vivo tumourigenicity study as well as protein and gene expression studies. M1S9, specifically comprised of saponin and amino acid, retained the lowest antioxidant activity and highest glucosinolates content as compared to other ratios. Cell viability decreased significantly in MCF-7 breast cancer cells and PMEC after treatment with M1S9. Solid tumour from MDA-MB-231 xenograft mice was inhibited up to 64.5% at third week after treatment with high-dose M1S9. High-dose M1S9 significantly decreased the expression of calcineurin (CaN) and vascular endothelial cell growth factor (VEGF) proteins as well as the secreted frizzled-related protein 1 (SFRP1) and solute carrier family 39 member 6 (SLC39A6) genes. This study provides new scientific evidence for the chemoprevention properties of MOLSr in breast cancer model.

Recently a measure termed F* was described, as an interpretable transformation of the F measure, also known as the Dice coefficient. Using elementary mathematical methods, it is shown that F* is in fact identical to a previously described measure, monotonically related to the F measure, and variously termed in previous publications, dating from the late 19^th to the late 20^th century, as the ratio of verification, the Jaccard similarity measure or index, the threat score, the Tanimoto index, and the critical success index. The origins of these different terms in different disciplines (weather forecasting, ecology, machine learning) may explain the repeated independent redescription of this measure.

The Ranau Earthquake that struck on 5, June 2015 and follow by February 2018 and April 2021, were a new disaster in Sabah and caused many Sabahan to panic. The unpredicted disaster also caused a serious impact on all aspects of life in Sabah. The earthquake has caused severe damage to eight primary schools in the vicinity of the epicenter; although no casualties were reported. However, the disaster has passing deep psychological effects among students. In this study, we examine how the primary school teachers enabled the student to be resilient during and after the disaster. Based on the interviews of 16 primary school students it was revealed that most of the teachers used WhatsApp to support resilience during and after the earthquake. Interviews with 16 primary school teachers revealed there were two main reasons for them to communicate with students namely, delivering emotional aid and monitoring their stress. Based on student interviews, five content categories of emotional support were identified: caring, reassuring, emotion sharing, belonging, and distracting. The main contribution of this study is social media can be used as a spontaneously and proactive tool to support student's resilience during and after the earthquake trauma.

Global waste generation keeps increasing over the year and requires innovative solutions to minimize their impacts on environmental quality and public health. Predicted 2.2 billion tonnes per year of global municipal waste generation in the year 2025 which 1.6 fold is higher than in 2012. Hence, a strategic plan must be ascertained to overcome the future challenges of MSW locally and globally. Universiti Putra Malaysia (UPM) coined an initiative to demonstrate a showcase pilot plant for green energy production from MSW. Therefore, the data was obtained from the survey and actual sampling within the UPM compound to estimate the MSW generated and it's potentially used for green energy production. It is estimated that 5.0 – 7.0 tonne per day of MSW generated which about 30 - 35% is an organic fraction. Upon separation, the organic fractions were digested into biogas through anaerobic. At the maximum conversion of organic fraction, about 775 kWh of electricity may able to generate from the waste. In this study, the complete biorefinery setup and utilize organic components from the MSW generated in UPM was proposed that the biogas subsequently will be used to produce green energy in the form of electricity or cooking fuel.

Electrification coverage in Sarawak is the lowest at 78.74%, compared to Peninsular Malaysia at 99.62% and Sabah at 82.51%. Kapit, Sarawak with its 88.4% populations located in rural areas and mostly situated along the main riverbanks has great potential to generate electrical energy by hydrokinetic system. Yearly water velocity data is the most significant parameter to perform hydrokinetic analysis study. Nevertheless, the data retrieved from local river databases are inadequate for river energy analysis, thus hindering its progression. Instead, flow rates and rainfall data had been utilised to estimate the water velocity data. This signifies no estimation of water velocity in an unregulated river by using water level data had been made. Therefore, a novel technique of estimating the daily average water velocity data in unregulated rivers is proposed. The modelling of regression equation for water velocity estimation was performed and two regression model equations were generated to estimate both water level and water velocity on-site and proven to be valid as the coefficient of determination values had been R² = 87.4% and R²=87.9%, respectively. The combination of both regression model equations can be used to estimate long-term time series water velocity data for type-C unregulated river in remote areas.

The information on the land use and soil conservation practice based on year 2006, 2010 and 2014, hence offering an opportunity to model the impacts of land use change on erosion, deposition and surface water runoff. Limitation in the use of hydrological models had been their inability to handle the large amount of input data that describe the heterogeneity of the natural system. In this study, a procedure that takes into account soil conservation practice based on the land use change, the response of soil erosion and sediment export from the George Town Conurbation catchment area, and average annual sediment yields were estimated for each grid cell of the watershed to identify the critical erosion areas of rural and urban planning proposes. Average annual sediment yield and data on a grid basis estimated using Universal Soil Loss Equation (USLE) and an emerging technology represented by Geographic Information System (GIS) used as a tool to produce a map for erosion rate. The changing of the land use from forest to agriculture and then to an urban area is a challenging task to research on land use demand for population, and environmental impact assessment is important for the planning of natural resources management, allowing research the modification of land use properly and implement more sustainable for long term management strategies. The challenge is to formulate strategies that would promote an integrated approach to the land use planning at an appropriate level as to address the issues that arose. Modelling for creating urban growth boundary for the George Town Conurbation must have to be controlled surface runoff and soil loss and sediment export from land use of the George Town Conurbation catchment.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Populaces are prominent indicators of livability in creating ‘street life’ for cities and public spaces. Evaluating people’s experiences is significant in creating a city liveliness and urban heritage trail. The exploration of design strategies that could allow them to integrated and connected with other spaces in the context of city and heritage as well as creating a social life among them. The measuring variables are people’s experience on the spaces; thus, create the pattern of behavior, which cause spaces liveliness, using Kuala Lumpur Heritage Trail as an example of pedestrian priority streets, city environment and heritage value. The aim of this research is to evaluate people’s experiences and analyze their behavior towards the urban street design within cities environment and Malaysia heritage values. The analyzed review comprising on the livability of the street in the context of interrelation between behavioral patter of people and the preferences of urban heritage. Hence, this paper will give an understanding of how people experiences the presence of urban streets and heritage values, thus, bringing liveliness to the streets.

Recent studies have been able to detect α-synuclein (αSyn) seeding in formaldehyde-fixed paraffin-embedded (FFPE) tissues from patients with synucleinopathies using seed amplification assays (SAAs), but with relatively low sensitivity due to limited protein extraction efficiency. With the aim of introducing an alternative option to frozen tissues, we developed a streamlined protein extraction protocol for evaluating disease-specific seeding in FFPE human brain. We evaluated the protein extraction efficiency of different tissue preparations, deparaffinizations, and protein extraction buffers using formaldehyde-fixed and FFPE tissue of a single Lewy body disease (LBD) subject. Alternatively, we incorporated heat-induced antigen-retrieval and dissociation using a commercially available kit. Our novel protein extraction protocol has been optimized to work with 10 sections of 4.5-µm-thickness or 2-mm-diameter micro-punch of FFPE tissue that can be used to seed SAAs. We demonstrated that extracted proteins from FFPE still preserve seeding potential and further show disease-specific seeding in LBD and multiple system atrophy. To the best of our knowledge, our study is the first to recapitulate disease-specific αSyn seeding behavior in FFPE human brain, with structural validation. Our findings open new perspectives in re-evaluating archived human brain tissue, extending the disease-specific seeding assays to larger cohorts to facilitate molecular subtyping of synucleinopathies.

The new digital infrastructure has become an important basis for the green development of agriculture. This paper selects provincial sample data from 2006 to 2022, constructs an indicator system to measure new digital infrastructure and agricultural green total factor productivity, and explores how new digital infrastructure can promote agricultural green development. The results show that: (1) the new digital infrastructure has a significant role in promoting the green development of agriculture, and this conclusion is still valid after processing endogeneity and heteroscedasticity; (2) Technology and land factors play an intermediary role in the promotion of green agricultural development by the new digital infrastructure, that is, the new digital infrastructure helps to improve the quality and technical level of cultivated land and thus promote green agricultural development; (3) Labor force factors optimize the mediating role of technology factors, that is, the higher the quality of labor force, the stronger the role of the new digital infrastructure in promoting the green development of agriculture through the technological path; (4) The effect of new digital infrastructure on the green development of agriculture is obviously heterogeneous, and the effect is more obvious in northwest China and the regions with lower marketization level, higher environmental regulation level. This study is helpful to clarify the relationship between new digital infrastructure and agricultural green development in China, and provide corresponding policy suggestions for promoting regional agricultural green development.

Abstract: Heavy metals (HMs) contamination is one of the main among abiotic factors affecting crop productivity and also threatens human health via consuming metal contaminated crops as a food source. Over the past few years, HMs have drawn a lot of attention due to their increased use for commercial purposes and their harmful effects on plants and other life forms, thus threatening human survival. However, in recent years, several methods have been adopted to combat the harsh effects of HMs. After phytohormones, use of mineral nutrients such as selenium (Se) in the prevention of HM stress has been explored by the researchers more recently. Selenium is an important micronutrient widely known for its antioxidant properties in both plants and animals. Exogenous Se inhibits metal uptake and its translocation and also improves the antioxidant system, thus imparts resistance to HM toxicity in plants. Moreover, Se also regulates the production of various osmolytes in cells that helps in developing cell osmolarity. Selenium also induces the production of different types of secondary metabolites (SMs) that are also involved in plant's secondary defense mechanisms to different stresses. Uptake of mineral nutrients is a vital process for plant growth and development, which is also positively correlated with Se under metalloid toxicity. However, in order to understand the exact mechanism of Se in HM tolerance, different metabolic processes stimulated by Se and their pathways need to be explored. Hence, this review focuses on the role of Se on nutritional status, antioxidants metabolism, interaction with phytohormones and its role in the regulation of various genes involved in Se induced HM tolerance. Thus, this study will help researchers in the future for the improvement of HM tolerance via Se application in plants.

A popular approach to learning about admixture from population genetic data is by computing the allele-sharing summary statistics known as f-statistics. Compared to some methods in population genetics, f-statistics are relatively simple, but interpreting them can still be complicated at times. In addition, f-statistics can be used to build admixture graphs (multi-population trees allowing for admixture events), which provide more explicit and thorough modeling capabilities but are correspondingly more complex to work with. Here, I discuss some of these issues to provide users of these tools with a basic guide for protocols and procedures. My focus is on the kinds of conclusions that can or cannot be drawn from the results of f₄-statistics and admixture graphs, illustrated with real-world examples involving human populations.

The integration of artificial intelligence (AI) into academic settings in Sabah, Malaysia, is transforming education and research landscapes. While AI technologies promise to enhance teaching, learning, and scholarly activities, they also pose challenges such as ethical concerns and skill gaps among academic staff. This study addresses the multifaceted impacts of AI adoption on academicians in Sabah, focusing on two key research questions: the impact of AI-based intelligent tutoring systems on student engagement, learning outcomes, and educational equity, and the challenges and opportunities in building academicians' capacity to integrate AI technologies effectively. Through a multidisciplinary approach, incorporating insights from education, computer science, social sciences, and ethics, this research aims to evaluate the effectiveness of AI tools in educational settings and identify strategies for skill development and infrastructure support. The study recommends empirical assessments within Sabah's educational institutions, considering contextual factors and fostering collaborative partnerships with local communities. Professional development programs, collaboration with industry partners, and improved access to AI infrastructure are proposed strategies. Longitudinal studies and interdisciplinary research initiatives are suggested for future research, along with qualitative methods to capture diverse perspectives. Ultimately, by embracing a collaborative and multidisciplinary approach, Sabah's academic community can harness the transformative potential of AI to advance education, research, and scholarship while promoting ethical and inclusive practices.

Abstract: The effect of some weather parameters (rainfall and temperature) on the production of oil palm in Peninsular Malaysia was investigated. Data were analysed using the Statistical Package for Social Sciences (SPSS 20.0 version), with descriptive statistics, time series analysis, and multiple linear regression (MLR) carried out. SPSS and Microsoft Excel 2010 were used to analyse the results. The MLR model determined the strength of the relationship between oil palm yield (dependent variable) and the changing variables of temperature and rainfall (independent variables). The regression output returned three components; regression coefficients, regression statistics and ANOVA. The findings of the study revealed medium to high rainfall variability at the rate of 0.0008. This implies that rainfall is increasing over time with variations in its amount and intensity. As rainfall increases oil palm FFB production is predicted to increase at a slow rate of 0.0009. The estimation of average annual temperature indicated an increase of 5.6℃ at the rate of 0.0357℃ per year with a temperature maximum of 32.01℃ and minimum of 25.45℃. The result also revealed an increase in oil palm yield at the rate of 0.2581 per year with a mean value of 176247.6. Overall, there is a significant difference in the impact of rainfall and temperature on oil palm yield. This signifies that rainfall has a significant impact on oil palm yield (FFB) compared to temperature.

Agroforestry practices evolve with the development of basic and advanced facilities, changes in natural and artificial factors of land use change. The study aims to examine the socioeconomic characteristics and compare satisfaction levels across forest products and vegetable farming of the agroforestry community in Khost Province. Data were collected from 662 farmers and was analyzed using univariate Analysis of Variances (ANOVA) and Multivariate Analysis of Variances (MANOVA). The results found that forest and vegetable products, including fruits, berries, herbs, mushrooms, wild animals, oils, wood, honey, okra, eggplant, carrot, cucumber, pine nuts, pepper, and timber has different impact in terms of satisfaction with basic and advanced facilities, knowledge about land use and impacts, natural and artificial factors of land use change, and positive and negative impact of land use change. The limitation of the study included an absence of exogenous factors in the model such as climate change, financial conditions, market fluctuations, regulatory system, an area in which the study is selected, research design, and current condition of endogenous factors. Overall, agroforestry practices can improve the socioeconomic development of agroforestry-dependent communities in Khost Province, Afghanistan. This study provided useful insights for policymakers and development practitioners to promote agroforestry practice adoption and improve the socioeconomic development of agroforestry-dependent communities. Future works could explore the implications of agroforestry practices on the socioeconomic development of other dependent communities in Afghanistan.

In this study, the effects of music therapy on anxiety for patients undergoing regional anaesthesia in an operating room was succinctly investigated. This investigation was largely based on the adapted Hospital Anxiety and Depression Score (HADS) and Spielberger State-Trait Anxiety Inventory (STAI-S), of patients undergoing regional anaesthesia in an operating room. A randomized control trial was performed on 90 patients due for surgery. The selected patients for regional anaesthesia were allocated to either the music therapy group who listened to music using headphones for the entire surgery or the no-treatment control group. Based on the findings, it has been conclusively demonstrated that music can decrease the patient's anxiety level. According to the socio-demographic evaluation, elderly patients have the highest stress hormones levels when compared to young patients. Although elderly patients are more likely to choose religious songs to help them relax, cortisol analysis revealed an increase in cortisol levels among the elderly compared with younger patients. As a result, music is especially important to be delivered to elderly patients. Nonetheless, there is no restriction against administering music to elderly patients because evidence from the Hospital Anxiety and Depression Score (HADS) and State-Trait Anxiety Inventory (STAI-S) has shown that music helps to shift their attention away from pain and complications and makes them feel tranquil. Similarly, the HADS and modified Spielberger STAI (STAI-S) analyses demonstrate a substantial outcome for both groups, with respondents responding positively. The study found that listening to music during regional anaesthesia might help people feel less worried.

Background: The two-stage technique combining the Endoscopic Retrograde CholangioPancreatography (ERCP) with common bile duct (CBD) clearance carried out before the laparoscopic cholecystectomy represents the most common approach for CBD stones. Over time, different techniques have been proposed to manage cholecysto- choledocholithiasis (CCL) advantageously in one stage. Among these, the laparoendoscopic rendez-vous (LERV) addresses the CCL issue with a laparoscopic cholecystectomy with insertion of a guide wire performed at initial stage of the procedure, followed by the clearance of the bile duct carried out by the endoscopists. The goal of this study was to evaluate the efficacy and safeness of LERV procedure recording results and complications, also making a comparison between our results and current literature. Methods: We reviewed our experience of all consecutive patients with cholecysto-choledocholithiasis managed with LERV between January 2018 and December 2023. LERV success rate, operative time, length of hospital stay, stone recurrence, incidence of endoscopic and surgical complications were analysed. Results: A total of 120 patients underwent LERV in our facilities. We reported a 97% LERV success rate, 1.6% conversion-to-open rate, a median intraoperative time of 122 (range 95-220) min. The median hospital stay was 4 (range 2-38) days. An overall morbidity of 15% was reported (18/120): 15 Clavien-Dindo type 1/2, 2 type 3a and one type 3b. In two cases a re-operation during the hospital stay was necessary. At a median follow-up of 14 months (3-59) five patients experienced stone recurrence requiring redo-ERCP in two cases. Conclusion: LERV offers the significant advantage of a single stage procedure and hospitalisation along with a lower risk of post-ERCP pancreatitis, failed CBD cannulation and complications. Our experience confirms safety and effectiveness of the technique for CCL management.

Background: Delivery of quality family planning services depends on availability of skilled health care providers, which is often a challenge in Low- and middle-income countries. This study evaluates the effects of a targeted training program on family planning services delivered by the Lady Health Workers (LHWs) in six districts of Punjab, Pakistan. The primary goal was to enhance the quality and accessibility of family planning services, recognizing the pivotal role of LHWs in community health. Methods: Using a robust panel data difference-in-differences (DiD) approach, we analyzed the electronic medical records (EMR) of 1,410 LHWs over a nine-month period. This timeframe in-cluded both pre-training (July to December 2022) and post-training (April to June 2023) phases. Our assessment focused on the impact of training on five outcome variables: the number of follow-up clients, the number of Intrauterine Contraceptive Device (IUCD) clients, the number of condom clients, the number of modern method clients, and the number of injection clients. We also con-sidered control variables such as LHW age, LHW education, the number of eligible couples in each LHW's catchment area, and a categorical variable for the districts. Results: The positive and statistically significant (p<0.05) coefficients across various service cat-egories – Follow Up Clients [Coeff: 1.00, CI: (0.30 - 1.70)], IUCD Clients [Coeff: 0.23, CI: (-0.01 - 0.46)], Condom Clients [Coeff: 1.41, CI: (0.97 – 1.86)], Modern Method Clients [Coeff: 1.82, CI: (0.96 – 2.68)], and Injection Clients [Coeff: 0.32, CI: (0.14 – 0.50)]. These findings indicate enhanced productivity among LHWs who have received training, with results significant at the 95% con-fidence interval (CI). Conclusion: The study highlights the effectiveness of targeted training programs in boosting family planning services at the community level and offers insightful implications for policy-makers and health practitioners. While focused on six districts in Punjab, these promising results emphasize the need for ongoing training and support for frontline health workers to bolster family planning initiatives.

Heavy metals pollution in the Straits of Malacca warrants the development of rapid, simple and sensitive assays. Enzyme-based assays are excellent preliminary screening tool with near real-time potential. The heavy-metal assay based on the protease ficin was optimized for mercury detection using Response Surface Methodology. The inhibitive assay is based on ficin action on the substrate casein and residual casein is determined using the Coomassie dye-binding assay. Heavy metals strongly inhibit the hydrolysis. A Central Composite Design (CCD) was utilized to optimize detection. The results show a marked improvement for the concentration causing 50% inhibition (IC50) for mercury, silver and copper. Compared to One-factor-at-a-time (OFAT) optimization, RSM gave an improvement of IC50 from 0.060 (95% CI, 0.0300.080) to 0.017 (95% CI, 0.0160.019), from 0.098 (95% CI, 0.0770.127) to 0.028 (95% CI, 0.0220.037) and from 0.040 (95% CI, 0.035.045) to 0.023 (95% CI, 0.0200.027), for mercury, silver and copper, respectively. A near real-time monitoring of mercury concentration in the Straits of Malacca at one location in Port Klang was carried out over a 4-h interval for a total of 24 h and validated by instrumental analysis with the result revealing an absence of mercury pollution in the sampling site.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

In recent years, the problem of ecosystem degradation caused by human activities has become increasingly serious. Vegetation restoration is a key means to solve this problem, which has increased. To address the suitability and structural optimization of vegetation restoration in the Loess Plateau, the MaxEnt model was used to quantify the impacts of environmental and human activities on the planting suitability of vegetation restoration species at the raster scale. Three layers of trees, shrubs, and herbs with 12 common vegetation restoration species were selected. The factor index system was constructed by combining climatic, ecological, and socio-economic data, and the MaxEnt model predicted land suitability. It was found that human activities significantly increased the unsuitable planting area. This especially affected Robinia pseudoacacia in the tree layer and Amorpha fruticosa in the shrub layer. Highly suitable and moderately suitable areas were mainly located in sparsely populated areas with close water sources. Through maximum suitability optimization, it was identified that the overall spatial distribution of the three layers in the study area was relatively consistent, and the structural dominance of trees + shrubs + herbs and single herbs in the vertical structure was obvious, which were concentrated in the southwestern and northeastern parts of the study area, respectively. In addition, organic content (OC) and distance from the road to woodland (RW) were the dominant factors affecting land suitability, with a contribution rate of more than 50% and up to 80%. These results provide a scientific basis for optimizing planting structures. They are of significant theoretical and practical significance in guiding vegetation restoration work.

In this work, we explore a the different forms of a new type of modified gravity, namely f(φ) gravity. We construct the Big Rip type for the energy density and the curvature of the universe. We show that dark energy is a result of the transformation of the field φ mass (dark matter) to energy. In addition, we provide that Ω_{m}≈0,050, Ω_{DM}≈0,2, Ω_{DE}≈0,746, is in excellent agreement with observation data. We explore a generalized formalism of braneworld modified gravity. We also construct a new field equations, which generalize the Einstein field equations. We provide a relation between the extra dimension in 3-brane with the vacuum energy density. We show that the energy density of matter depends directly on the number of dimensions. We manage to find the value of the Gauss-Bonnet coupling α=1/4 which is a good agreement with the results in the literature, this correspondence creates a passage between f(R) gravity and Gauss-Bonnet gravity, this comparison leads to a number of bulk dimensions equal to D=10¹²¹+4.

In many application problems, F-transform algorithms are very efficient. In F-transform techniques, we replace the original signal or image with a finite number of weighted averages. The use of weighted average can be naturally explained, e.g., by the fact that this is what we get anyway when we measure the signal. However, most successful applications of F-transform have an additional not-so-easy-to-explain feature: the partition requirement, that the sum of all the related weighting functions is a constant. In this paper, we show that this seemingly difficult-to-explain requirement can also be naturally explained in signal-measuring terms: namely, this requirement can be derived from the natural desire to have all the signal values at different moments of time estimated with the same accuracy.

Herein, we examined the effects of weather parameters and individual clinicodemographic risk factors on hemorrhagic stroke (HS) incidence, severity on admission, and disability at discharge in a harsh desert climate. In a retrospective design we studied patients admitted to a stroke unit in Arab Emirates in 2016-2019. With a distributed lag nonlinear model we explored immediate and delayed effects of weather on stroke incidence. Supervised machine learning was used to build models predictive of scores in NIHSS and mRS scales. We assessed model performance by calculating ROC AUC, F1 scores, specificity, and sensitivity. HS risk increased after a significant change in any weather parameter. The risk was reduced below baseline after 1-week adjustment to environmental changes. Climate input from the previous 3 days yielded reliable classification models. Humidex was a better predictor of severity than air temperature, whereas body mass index, age, and time of day at stroke onset were the strongest clinical predictors. Weather parameters before admission were stronger predictors of disease severity than individual clinical factors. We addressed limitations of previous studies by analyzing a full set of climate parameters: ambient temperature, relative humidity, humidex, atmospheric pressure, and wind speed. Predictive models may help to optimize patient management and develop preventative strategies.

Litsea martabanica root's antioxidant and AChE activity showed promise as a pesticide detoxification agent in our previous study. In addition to roots, its leaves can help mitigate pesticide exposure, although there is limited scientific evidence supporting their efficacy. However, the use of roots in many countries, such as Thailand, could contribute to environmental degradation, as highland communities traditionally cut down whole trees to obtain them. This study aims to evaluate the antioxidant activity and anti-pesticide potential of water extracts from L. martabanica leaves instead of its roots through in vitro and in vivo investigations. The findings showed that L. martabanica water extracts and fractions demonstrated varied antioxidant activity. The water extract, obtained using traditional extraction methods, was chosen for in vivo experiments. Rats received the extract followed by chlorpyrifos exposure for 16 days. Results indicated reduced acetylcholinesterase activity in chlorpyrifos-exposed rats, while treatment with leaf extract led to increased activity, suggesting its potential as a detoxifying agent. Histopathological examination revealed no liver cell necrosis and showed liver cell regeneration, indicating potential protection against free radical-induced liver damage without affecting rat liver weight or biochemical profiles. Utilizing L. martabanica leaves for healthcare purposes holds promise without negative environmental impact.

In this paper we have defined the effect of bulk viscosity on Quintessence model and scaler field potential as well as on classical field. We have shown the same effect for modified gravity with f(R,T)= R+f(T). In the derivation we have predicted the possibility of time dependent evolution of gravitational constant G and anisotropy.

The compatibility between the de Sitter Swampland conjecture and Ho\v{r}ava-Lifshitz $F(\bar{R})$ theories with a flat FLRW metric is studied. We first study the standard $f(R)$ theories and show that the only way in which the dS conjecture can be made independent of $R$ is by considering a power law of the form $f(R)\sim R^{\gamma}$. The conjecture and the consistency of the theory puts restrictions on $\gamma$ to be greater but close to $1$. For the $F(\bar{R})$ theories described by its two parameters $\lambda$ and $\mu$ we use the equations of motion to construct the function starting with an ansatz for the scale factor in the Jordan frame of the power law form. By doing a conformal transformation on the three metric to the Einstein frame we can obtain an action of gravity plus a scalar filed by relating the parameters of the theory. The non-projectable and projectable cases are studied and the differences are outlined. The $F(\bar{R})$ function obtained consists of terms of the form $\bar{R}^{\gamma}$ with the possibility of having negative power terms. The dS conjecture leads to inequalities for the $\lambda$ parameter, in both versions it gets restricted to be greater but close to $1/3$. For the general case in which $\mu$ and $\lambda$ are considered as independent, the action contains an extra term but we propose that the conjecture is still applicable. Once again the non-projectable and projectable cases are studied. The $F$ function obtained has the same form as before, the consistency of the theory and the dS conjecture lead to a set of inequalities on both parameters that are studied numerically. In all cases $\lambda$ is restricted by $\mu$ around $1/3$ and we obtain $\lambda\to1/3$ if $\mu\to0$. Finally we consider the $f(R)$ limit $\mu,\lambda\to1$ and we obtain consistent results.

Polycystic ovary syndrome (PCOS) is a common endocrine disorder in women, characterized by fluid-filled sacs in the ovaries and various symptoms including high androgen levels, endometrial irregularities, and cysts. While the cause of PCOS is unknown, it has been linked to genetic, endocrine, and metabolic factors, and there are several treatment options, including lifestyle modifications, medications, and surgery. Natural products, such as medicinal plants and fruits, are being explored as potential treatments for PCOS due to their bioactive compounds with pharmacological effects related to antioxidant, antimicrobial, anticancer, and antidiabetic properties. Some of these compounds improve insulin sensitivity, reduce inflammation, and enhance glucose metabolism, which is beneficial for women with PCOS. This review examined the effects of natural products on PCOS, including their effects on ovarian histological changes, blood glucose, sex hormones, and lipid profile, based on animal and human studies. This study suggests that the use of natural products as complementary medicine can be a promising resource for the development of effective therapeutics for PCOS, but that further research is needed to fully understand their benefits

The Indian meal moth, Plodia interpunctella, poses a significant threat to global agricultural products. Although pheromone-based technologies show promise for P. interpunctella management, limitations like single-sex targeting necessitate exploring complementary strategies. Vegetable-based oils represent a potential alternative, but their efficacy, sex-specificity, and interaction with sex pheromones remain unclear. To answer these questions, we first examined attraction of P. interpunctella female and male adults to ten different vegetable oils, i.e., camellia, corn, olive, peanut, rapeseed, sesame, soybean, sunflower, walnut, and a blended oil (mixture of sunflower seed, rapeseed, soybean, peanut, and sesame oils), in the semi-field conditions. Sesame, olive, and blended oils demonstrated most attractive, capturing significantly more adults compared to other oils. We then evaluated effectiveness of these three attractive oils and their combinations with P. interpunctella sex pheromone in a grain warehouse. Traps baited with these oils captured significantly more females and males compared to control traps without attractants. However, sex pheromone addition did not improve male capture and significantly reduced female capture, suggesting an inhibitory effect. Our findings highlight the potential of blended, olive, or sesame oil trap alone as alternative monitoring and trapping tools for P. interpunctella, delivering novel insights into the development of efficient integrated pest management strategies for stored products.

Crop digital twin is redefining traditional farming practices, offering unprecedented opportunities for real-time monitoring, predictive and simulation analysis, and optimization. This research embarks on an exploration of the synergy between precision agriculture, crop modeling, and regression algorithms to create a digital twin for augmenting farmers the concentration and composition prediction-based crop nutrient recovery. This captures the holistic representation of crop characteristics, considering the intricate relationships between environmental factors, nutrient concentrations, and crop compositions. However, the complexity arising from diverse soil and environmental conditions makes nutrient content analysis expensive and time-consuming. This paper presents the result of a predictive digital twin case study that employs six regression algorithms namely Elastic Net, Polynomial, Stepwise, Ridge, Lasso, and Linear Regression to predict rice nutrient content efficiently, particularly considering the coexistence and composition of multiple nutrients. Our research findings highlight the superiority of the Polynomial Regression model in predicting nutrient content, with a specific focus on accurate nitrogen percentage prediction. This insight can be used for nutrient recovery intervention by knowing the precise amount of nutrient to be added into the crop medium. The adoption of the Polynomial Regression model offers a valuable tool for nutrient management practices in the crop digital twin, potentially resulting in higher-quality rice production and a reduced environmental impact. The proposed method can be replicable in other low-resourced crop digital twin system.

The rural road landscape is crucial in forming rural areas' landscape character (LC). As a platform for portraying the rural landscape, the rural roads demonstrate the area's unique natural and cultural characteristics to the visitors. However, with the continuous development of rural areas, the rural LC has been severely impacted, thus impacting visitors' visual experience. In order to preserve and protect the rural landscape, this study aims to assess the visual quality of rural road landscapes based on public preference and heatmap analysis. The results indicated that most of the participants had a higher level of preference for rural landscapes with open horizontal views represented by agricultural areas such as paddy fields. It was also found that different paddy field characters based on their planting stages can also positively affect the visual quality of rural road landscapes. The study also revealed that rural LCs with roadside settlements, commercial structures, mixed agricultural crops, and vegetation received low preference ratings. These characters negatively impact the visual quality of the rural road landscape. These findings provide significant insight for planners and decision-makers regarding protecting and preserving the essential rural road landscapes for the rural tourism experience.

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO2 thin films were elucidated using real-time synchrotron radiation imaging, its structure determined using grazing incidence X-ray diffraction (GIXRD), its morphology imaged using the field emission scanning electron microscopy (FESEM), and its surface topography examined using the atomic force microscope (AFM) in contact mode. Cubical white spots were detected, identified as Ag, while the TiO₂ thin film resembles a porous ring-like structure with each ring coalescing and forming channels. Junction growth is directly proportional with time under continuous heating conditions (annealing), and its growth orientations and patterns were seemingly random.

The new emergence and re-emergence of arbovirus infections vectored by Aedes mosquitoes have been spread across Southeast Asia, Central Africa, United States, tropical Oceania and become a major of public health concerns. These arbovirus diseases found to have a similar vector, symptoms of the diseases and environments. The situation has become complicated without any specific vaccine or treatment for the diseases. As far as we concern, vector control is the best defense with many challenges, a scattered breeding site and biological behavioral sometimes, more difficult to control. Herein, we present a review of studies on current techniques proposed to combat arbovirus infections vectored by Aedes mosquitoes. A crucial gap in a vector control program is the inability to eliminate and destroy the cryptic breeding site by using conventional control methods. The idea and proper concept of using mosquitoes to bring insecticide to their oviposition site had been getting more interest in people to explore. Autodissemination is a self-delivery technique by manipulating the behavior of mosquitoes, carrying the insecticide and disseminate to cryptic breeding sites. This technique has shown a promising result in some countries and can be considered as additional tools in a vector control program

Gender recognition is trivial for physiotherapist, but it is considered a challenge for computers. The electromyography (EMG) and heart rate variability (HRV) were utilized in this work for gender recognition during the stepping exercise using a stepper. The relevant features were extracted and selected. The selected features were then fused to automatically predict gender recognition. However, the feature selection for gender classification became a challenge to ensure better accuracy. Thus, in this paper, a feature selection approach based on both the performance and the diversity between the two features from the rank-score characteristic (RSC) function in a combinatorial fusion approach (CFA) was employed. Then, the features from the selected feature sets were fused using a CFA. The results were then compared with other fusion techniques such as naive bayes (NB), decision tree (J48), k-nearest neighbor (KNN) and support vector machine (SMO). Besides, the results were also compared with previous researches in gender recognition. The experimental results showed that the CFA was efficient for feature selection. The fusion method was also able to improve the accuracy of the gender recognition rate. The CFA provides much better gender classification results which is 94.51% compared to Nazarloo's work (90.34%) and other classifiers.

We investigate alternative candidates to dark energy that can explain the current state of the universe in the framework of the generalized teleparallel theory of gravity f(T ) where T denotes the torsion scalar. To achieve this, we carried out a series of reconstruction taking into account to the ordinary and entropy-corrected versions of the holographic and new agegraphic dark energy models. These models used as alternative to dark energy in the literature in order describe the current state of our universe. It is remarked that the models reconstructed indicates behaviors like phantom or quintessence models. Furthermore, we also generated the EoS parameters associated to entropy-corrected models and we observed a transition phase between quintessence state and phantom state as showed by recent observational data. We also investigated on the stability theses models and we created the {r − s}. The behavior of certains physical parameters as speed of sound and the Statefinder parameters are compatible with current observational data.

The objective of this study was to investigate the umami characteristics of soy sauce using electronic tongue evaluation and amino acid composition and Matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) analysis. The soy sauce peptides were isolated from soy sauce using XAD-16 macroporous resin combined with ethanol solution. Results showed that the soy sauce peptide fraction eluted by 60% ethanol (SS-60%) exhibited a prominent umami taste and the umami scores were highly positively correlated with the amino acid nitrogen contents of soy sauces. The umami scores of SS-60% were significantly positively correlated with the contents of free amino acids. Especially, Phe showed the highest positive correlation with the umami scores. In addition, five characteristic ion peaks with m/z at 499, 561, 643, 649, and 855 were identified in the peptide mass fingerprinting. Therefore, this study provides new insights into the umami characteristics for the flavor evaluation and reality identification of soy sauce.

In this work we present a novel steganography algorithm, based on Fractal Transform domain, combined with the principles of Cryptography. The proposed method uses a private key, which will indicate which segment of the image will be taken and encoded with the Fractal Transform, to then insert the secret bits in the transformed coefficients, thus generating the stego image.

Temperature Cycle Induced Deracemization (TCID) offers a promising approach to obtain enantiopure solids from racemic mixtures. By combining rapid racemization in solution and temperature swings, homochirality is theoretically achieved. Despite theoretical expectations of doubled yields compared to traditional chiral separation methods, such as in Preferential Crystallization, experimental validation remains lacking. We applied TCID to (1-(4-chlorophenyl)-4,4-dimethyl-2-(1H-1,2,4-triazol-1-yl) pentan-3-one) (Cl-TAK), introducing a post-TCID cooling step to enhance yield and a washing step to augment enantiopurity. This refinement yielded an 89.8% mass yield with 99.1% enantiomeric excess in the crystal phase (c.e.e.) within 24 hours on an 8.75g scale, showcasing improved performance with insignificant process duration extension. Additionally, we explored the stochasticity of deracemization, observing the development from low initial crystal enantiomeric excesses(1-6% c.e.e0) at a 2.5 g scale. Kinetic analysis revealed that a 2% c.e.e0 effectively mitigates chiral flipping risks and induction time in our system. Our study underscores the potential for reduced initial c.e.e. to expedite deracemization and presents a straightforward method to optimize yield and purity, facilitating industrial application.

This study aimed to characterize the antioxidant, mechanical and physical properties of chicken skin gelatin/CMC/Centella asiatica blended film. The influence of Centella asiatica at 0.3% and 0.7% on antioxidant activities; mechanical properties and physical properties of chicken skin gelatin/CMC/Centella asiatica film were investigated. Characterization of the blended films with 0.7% Centella asiatica extract shows higher antioxidant activities with a total phenolic content of 0.36 mg/g of GAE, DPPH of 89.26%, and reducing power of 0.80 nm compared to 0.3% Centella asiatica extract. The addition of 0.3% of Centella extract provide higher value in tensile strength (5.0 × 10⁻² MPa), elongation at break (281%), melting point (131.31 °C), transparency (0.86) but lower UV-light penetration. While the addition of 0.7% Centella extract contribute to higher value in WVP (1.13 × 10⁻⁴ g m⁻¹s⁻¹Pa⁻¹) and puncture test (0.06 N). There are no significant differences between functional groups obtained from this blended film as evaluated by FTIR analysis (p > 0.05). Furthermore, XRD analysis showed the addition of extract decrease the crystallinity of film. In conclusion, the incorporation of Centella asiatica extracts on film greatly increased antioxidant levels and improved some of the mechanical and physical properties of the film blends.

Phage, which is often used therapeutically, has begun to receive interest as an alternative to antibiotic growth promoters (AGPs) to enhance chicken growth. Another option that has been extensively studied as a growth promoter in chicken is probiotics. However, there are no studies using phages and probiotics as prospective feed additives for broiler chickens. Therefore, this study demonstrated the effects of phage cocktail, probiotics and their combinations on growth performance and gut microbiota of broiler chickens. A total of 288 one-day-old male Cobb 500 broilers were randomly allotted to 1 of 6 treatments in a completely randomised design. The treatments were: (i) C (basal diet (BD) only), (ii) 1ɸ (BD + 0.1% phage cocktail), (iii) 2ɸ (BD + 0.2% phage cocktail), (iv) P (BD + 0.1% probiotic), (v) 1ɸP (BD + 0.1% phage cocktail + 0.1% probiotic), (vi) 2ɸP (BD + 0.2% phage cocktail + 0.1% probiotic). The 1ɸP treatment had significantly (P < 0.05) better BW (35 d), BWG (22 – 35 d, 1 – 35d), and FCR (1-21 d. 22-35 d, 1-35 d) compared to C. Unique gut microbiota diversity was also found between the ɸP (1ɸP and 2ɸP) and non-ɸP groups (C, 1ɸ, 2ɸ and P) in ilea, particularly in the 35 d chickens. Microorganisms associated with short-chain fatty acid (SCFA) producers were significantly (P <0.05) present in the ɸP group than in the non- ɸP group. The carbohydrate and amino acid metabolism predicted genes were significantly upregulated in ɸP groups compared to non- ɸP groups. These genes were involved in the digestion and absorption of nutrients as well as the production of energy. Our findings showed that 1ɸP treatment could be a potential alternative to AGPs for poultry where growth performance was enhanced, and gut microbiota was positively modulated.

Genetic disorders are preeminent determinants of infant mortality. The inherited pediatric-onset genetic disorders have consequential stress on child growth and development: several congenital, complex and rare disorders with indistinguishable clinical symptoms where diagnosis always remains a challenging task. Traditional diagnosis methods include biochemical tests followed by chromosomal microarray and sequencing of a single gene or panel of genes. These methods had several limitations, but with the advent of whole-exome sequencing (WES), genetic testing has become cost-effective and transformative. Exome sequencing has been known for its effectiveness, which appropriately elucidates and distinguishes the heterogeneous disorders to avoid misdiagnosis and decode the underlying genetic alterations. WES has led to discovering genes and genomic variants in a broad spectrum of diseases, including autism, epilepsy, congenital heart diseases, neurodevelopmental diseases, cancer, nephrotic disorders, neural tube defects and fetal structural anomalies. WES is significant in producing immense genomic biomarkers that can be made as appropriate pharmacogenomic targets for drug therapy. In this article, we analyze the recent exploration of WES technology to revolutionize not only the process of genetic variation and disease detection but also the convention of preventative and targeted drug discovery.

Cotton (Gossypium spp.) is the most important fibre crop worldwide. Black root rot and Fusarium wilt are two major diseases of cotton caused by soil-borne Berkeleyomyces rouxiae and Fusarium oxysporum f. sp. vasinfectum (Fov), respectively. Phenotyping plant symptoms caused by soil-borne pathogens has always been a challenge. To increase the uniformity of infection, we adapted a seedling screening method that directly uses liquid cultures to inoculate the plant roots and the soil. Four isolates each of B. rouxiae and Fov were collected from cotton fields in Australia and were characterised for virulence on cotton under controlled plant growth conditions. While the identity of all four B. rouxiae isolates were confirmed by multi-loci sequencing, only two of them were found to be pathogenic on cotton, suggesting variability in the ability of isolates of this species to cause disease. The four Fov isolates were phylogenetically clustered together with the other Australian Fov isolates and displayed both external and internal symptoms characteristic of Fusarium wilt on cotton plants. Furthermore, the isolates appeared to induce varied levels of plant disease severity indicating differences in their virulence on cotton. To contrast the virulence of the Fov isolates, four putatively non-pathogenic Fusarium oxysporum (Fo) isolates collected from cotton seedlings exhibiting atypical wilt symptoms were assessed for their ability to colonise cotton host. Despite the absence of Secreted In Xylem genes (SIX6, SIX11, SIX13 and SIX14) characteristic of Fov, all four Fo isolates retained the ability to colonise cotton and induce wilt symptoms. This suggests that slightly virulent strains of Fo may contribute to the overall occurrence of Fusarium wilt in cotton fields. Findings from this study will allow better distinction to be made between plant pathogens and endophytes and allow fungal effectors underpinning pathogenicity to be explored.

Microalgae are known as a rich source of bioactive compounds which exhibit different biological activities. Increased demand for sustainable biomass for production of important bioactive components with various potential especially therapeutic applications has resulted in noticeable interest in algae. Utilization of microalgae in multiple scopes has been growing in various industries ranging from harnessing renewable energy to exploitation of high-value products. The focuses of this review are on the isolation of bioactive compounds from microalgae regarding different metabolites which are currently used and new possible applications of the compounds in industries and future prospects. Moreover, this work discusses the advantage, potential new beneficial strains, applications, limitations, research gaps and future prospect of microalgae in industry.

Metal nanoframes have gained tremendous attention in the domain of modern research and development due to their distinctive 3D spatial structure, efficient physiochemical properties, and comparatively good activity. Different strategies have been implicated by the researchers to design nano frame of varying chemical nature and shapes. Most of the synthetic protocols being adopted to design a nano framee, mainly consist of two main steps, nucleation and growth of solid particles and secondly excavation of the interiors. In this context, many synthetic methods are overviewed. To show their unprecedented performance or activity, a few applications in catalytic, biomedical, theranostic, SERS, sensing of different materials, reduction of CO2, etc are also discussed.

Yeast extract is widely used in different food industries as a flavoring agent or vitamin supplement. In this study, a process was optimized for the production of yeast extract from Baker’s yeast (Saccharomyces cerevisiae). A glass vessel stirred fermenter was used for the cultivation of yeast biomass. The effect of various physical and chemical factors was evaluated on the production of yeast cells and optimum conditions for the production of maximum yeast biomass were determined. The optimum growth was obtained at 30ºC with pH 4.5 using molasses as a substrate supplemented with urea at 150rpm. Yeast cells were then separated by centrifugation and ruptured and autolysis was observed to be the most feasible method. Among various method employed to dry the yeast extract, spray dryer appeared as most efficient one. Yeast extract obtained after drying was subjected to different analyses and compared with commercial yeast extract. The produced yeast extract was applied in media preparation to grow different microorganisms including yeast, bacteria and fungi and considerable growth was observed. These results indicated that the developed process is a cost effective alternate approach for the production of yeast extract.

While there has been a tremendous decline in malaria disease burden in the remote parts of the Malaysia, little is known about malaria incidence in its urban localities. This study aimed to analyse trends of malaria cases in urban Kuala Lumpur, Malaysia. All suspected cases presented to a university hospital in Kuala Lumpur from January 2005 to December 2020 were examined by microscopy. Infection status was analysed using descriptive statistics and curve estimation analysis. Of 3105 blood films examined, 92 (3%) were microscopically confirmed malaria cases. Plasmodium vivax infections accounted for the majority (36.9%) of all malaria cases. Nearly half (47.8%) of cases were found among foreign cases (P&lt;0.001). The majority of foreign cases were males (86.4%) and came from Southeast Asian countries (65.9%). Curve estimation analysis showed significant decreases of malaria cases due to P. vivax (R2 = 0.598; P&lt;0.001) and Plasmodium falciparum (R2 = 0.0259, P = 0.029), but increase for Plasmodium knowlesi (R2 = 0.325, P = 0.021) during the 16 years. This study revealed that malaria incidence in urban Kuala Lumpur is low and has remained stable since 2005. However, P. knowlesi played a significant role in the increase of overall malaria in the area, highlighting the importance of continued vigilance and improved surveillance.

Assessment of stigma among cancer patients is of utmost importance as stigma may lead to various psychological sequelae and lower quality of life. This study aimed to translate the English version of the Shame and Stigma Scale (SSS) into Malay and validate the Malay version of the SSS (SSS-M) among cancer patients in Malaysia. Initially, concurrent translation and back translation of the SSS-M was performed, and face and content validity were assessed. Then, the SSS-M was administered to a total of 234 patients of mixed types of cancer to assess its reliability (internal consistency and test-retest reliability), construct validity (convergent and discriminant validity), exploratory factor analysis (EFA) and confirmatory factor analysis (CFA). The SSS-M total score registered good internal consistency (Cronbach’s α of 0.886) and test-retest reliability (intraclass correlation coefficient of 0.846, p < 0.001). EFA and CFA confirmed that the SSS-M consisted of 20 items in 5 domains. Its convergent and discriminant validity were achieved. Hence, the SSS-M demonstrated good psychometric properties and is available for use to assess stigma among cancer patients in Malaysia.

A Zn(II) perchlorate complex has been prepared and characterized by single X-ray crystallography, nuclear magnetic resonance spectroscopy, thermogravimetric analysis, infrared spectroscopy, elemental analysis, and UV-vis spectroscopy. The complex crystallizes in the monoclinic space group P21/c (Z = 4) with a pentacoordinated zinc center. Interestingly, the Zn complex was found be to a potential fluorophore that could sense acetone and other ketones with high selectivity and sensitivity.

Here are given tight probabilistic inequalities that provide nearly best estimates for the Csiszar's f-divergence. These use the right and left psi -Hilfer fractional derivatives of the directing function f. Csiszar's f- divergence or the so called Csiszar's discrimination is used as a measure of dependence between two random variables which is a very essential aspect of stochastics, we apply our results there. The Csiszar's discrimination is the most important and general measure for the comparison between two probability measures. We give also other applications.

Biogenic emission can have significant impact on atmospheric chemistry. Isoprene (C5H8) is known as the most predominant volatile organic compound and its emission is highly dependent on temperature and light (solar radiation). This study aims to investigate future changes of isoprene emission under climate change scenario. The Southeast Asia (SEA) region is home to 15% of the world’s tropical forest, and the biogenic emission from this region can have significant effect on the global climate chemistry. Three climate change scenarios (RCP4.5, RCP6.0 and RCP8.5) were used to drive climate change simulation in 2013 (baseline), 2030 (near-future), 2050 (mid-century), 2070 (post-mid) and 2100 (end of century) using the Weather Research Forecasting (WRF v3.9.1) model. The Model Emission of Gases and Aerosol from Nature (MEGAN v2.1) was then used to simulate isoprene fluxes using climate output datasets from the WRF model. This study highlights that the projected mean surface temperature and PAR (photosynthetic active radiation) were higher in July than in January. Towards the end of the century, the overall surface temperature and PAR over the SEA region is expected to increase by 0.9℃ - 2.1℃, and 7.6 W m-2 – 12 W m-2 under all RCPs. The all-time high isoprene emitters are Borneo and Papua Island. Meanwhile, the projected increment of isoprene emission over this region is between 10 – 14%, 15-30% and 29 – 53% for RCP4.5, RCP6.0 and RCP8.5, respectively. Our result concludes that the total isoprene emission was higher during July, consistent with the high surface temperature and PAR. The results also agreed with the hypothesis of high isoprene emission over the region that has oil palm plantation. Thus, challenges in dealing with future emissions of isoprene in SEA are closely tied to future climate policies to limit the warming of the atmosphere over this region and the land-use conversion of palm oil plantations.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

Pharmaceuticals contain biologically active components that can pollute water courses as a result of the excretions from individuals and/or uncontrolled release of residues from chemical plants, and they can pose a hazard to health. Pharmaceutical residues can persist at low concentrations in the environment, and thus may be potentially harmful to aquatic animals and to humans. Controlling and monitoring such residues are therefore a prime interest, for example, a solid-phase extraction uses solid sorbents to purify and preconcentrate the residues prior to their chemical analysis. In the present study, poly (acrylonitrile-co-divinylbenzene-80) sorbents are synthesised by varying the comonomer feed ratios under precipitation polymerisation conditions to deliver a family of porous polymer microspheres. Acrylonitrile confers polar characters onto the sorbents, and the acrylonitrile-derived nitrile groups can be chemically transformed via polymer-analogous reactions into thioamide and sulfonated residues which make the sorbents even more suitable for the capture of polar analytes, including selected pharmaceuticals. The utility of the porous thioamide-sulfonated containing sorbents is demonstrated via the dispersion-solid phase extraction of mefenamic acid from aqueous media; mefenamic acid is an anthranilic acid derivative which is a potent, non-steroidal anti-inflammatory drug which is found in environmental waters at low concentrations.

Increase demand for palm oil production has indirectly increased waste and pollution. Empty fruit bunch (EFB), which is the major solid waste from this industry, has the potential to be further treated into valuable product. In this study, cellulose will be extracted from EFB through alkali treatment and acid hydrolysis treatment with a different approach and further modified via acetylation and silylation technique. The modified samples are to be utilized to reduce pollution due to palm oil mill effluent (POME) and carbon dioxide (CO2) emission from the industry. The characterization of the extracted and modified cellulose was carried out using attenuated total reflectance-Fourier transform infrared (ATR-FTIR), thermogravimetric analysis (TGA) and scanning electron microscope (SEM). ATR-FTIR analysis revealed that the cellulose was successfully extracted from raw EFB and the cellulose-acetyl, nanocrystalline cellulose (NCC) and cellulose-2 has been successfully modified from the cellulose. TGA analysis shows that both modified cellulose have higher thermal stability compared to raw EFB and extracted cellulose. SEM morphology of the modified cellulose shows a higher surface area due to the wrinkled formation while the wax layer and cuticle pore has been diminished clearly. The modified sample gave a significant performance where cellulose-acetyl absorbed 98.5% of oil compared to unmodified cellulose-1 sample that only absorbed 5% of oil from POME. NCC-AEAPDMS adsorbed physically and chemically 3.5 cm3/g CO2 gas compared to NCC sample, which undergoes only physical adsorption with maximum capacity up to 2.4 cm3/g. Thus, modification can enhanced the performance of cellulose for industrial applications.

Remanufacturing is a way for product recovery initiative and maintaining sufficient production flow to satisfy customer demand through circular economy. Recently, manufacturers have been progressively incorporating remanufacturing processes, making their supply chain vulnerable to disruptions. Among the disruptions that usually occur is the shortage in spare parts supply, which causes unexpected delay in production and possible loss of sales. In the face of potential disruption, it is essential for remanufacturing facilities to manage their supply chains in an optimum manner as to decrease the adverse impact of disruptions to their business. In this study, a two-stage production-inventory system is analysed by developing a cost-minimisation model focusing on the recovery schedule after a disruption occurrence in sourcing spare parts for a remanufacturer’s production cycle. The developed model was solved using the branch and bound algorithm. Through numerical experiments, the results indicate that the optimal recovery schedule and the number of recovery cycles are significantly dependant on disruption time, lost sales and backorder costs. Moreover, a sensitivity analysis shows that the lost sales option seems to be more effective than the backorder option in optimising the system’s overall cost. The proposed model could assist managers in deciding the optimal production strategy while providing interesting managerial insights into vital spare parts recovery issues when disruption strikes.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

Biofilm-associated proteins (BAPs) are important in the development and resilience of biofilms, which are intricate populations of microbes protected by extracellular matrix. All members of the BAP family are known to possess common characteristics such as high molecular weight and a signal sequence for extracellular secretion. It has been shown that BAPs are directly linked to the pathogenicity of many bacteria. This mini review highlights several potential strategies to target BAPs for drug development.

This chapter is written for the welfare of the society, questioning and enlightening the effects of the increment or decrement in the percentage of quality of air causing pollution due to the rise in the traffic post-lockdown due to COVID-19 in metro cities, specifically in Delhi. In this chapter, we address the question about people's preference in moving in the shared taxis to their workplaces or their reluctance and denial of the idea of moving in the shared vehicle because of the fear of getting infected. The sensitivity of the situation will compel the people to move in a single occupied vehicle (SOV). The rise in the number of vehicles on the roads will result in traffic jams and different kinds of pollution where people battling with the pandemic will inevitably get exposed to other health-related issues. We use a BPR (Bureau of Public Roads) model to combat this issue endangering the environment and public health. We exploit the BPR function to relate average travel time to the estimated number of commuters travelling by car. We collect mode share data from the NITI Ayog, the State Resource Centre and other authentic sources, which gives unique figures of the impact of shared mobility in India and how, in its absence, various sectors will get affected. Using the given data and the BPR, we evaluate increased vehicle volumes on the road if different portions of transit and carpool users switch to single-occupancy vehicles and its effect on multiple other factors. Based on the study of densely populated city, Delhi, we predict that cities with significant transit ridership are at risk for extreme traffic and pollution unless transit systems can resume safe with effective protocols.

The recent happenings in the world such as flood and wild forest fire were as a result of climate effect as being envisaged by scientists. It is urgent now to adopt a source of energy that will eliminate this effect on our universe. Solar energy is the major energy means that is abundant which could be utilized. In this review, the prospects of solar energy exploration were studied in Nigeria which include assessments, economic viability and hybrid systems. Findings show higher potential in the North as compared to the Southern region. Additionally, potential of offshore solar energy system was simulated by considering 2002, 2003 and 2004 data sets from Era5-land base. Their monthly mean, seasonal changes and annual mean value were estimated. The algebraic annual solar radiance for 2002, 2003 and 2004 were 34,914.732 kWh/m2, 33,898.316 kWh/m2 and 34,338.324 kWh/m2. Suggestions were made due to the present status of solar energy utilization that will enhance its maximum usage and development. One of these is the establishment of a functioning financial scheme and the database for all renewable energy systems. When all these are put in place, the energy supply will increase, climate effect will be reduced, and the economy will be boosted.

The hydrocarbon generation potential of Chia Gara strata and their genetic link with produced oils from the Zagros basin are still not comprehensively investigated. Forty-seven rock samples from the Tithonian–Berriasian interval were subjected to geochemical analyses to infer organic matter enrichment, hydrocarbon potential, thermal maturity, and timing for hydrocarbon generation/expulsion and their implications regarding upcoming petroleum explorations in the Zagros basin. The results showed that the Chia Gara rock samples have fair to very-good generation potential, as confirmed by higher total organic carbon (TOC=0.68–3.95 wt%) and Rock-Eval (S1+S2=3.37–8.52 mg HC/g rock). The hydrogen index (HI=171–462) and Rock-Eval Tmax over 430 °C support the presence of Types II and mixed Types II/III kerogen. These results confirm the high generation potential of the Chia Gara Formation in the study region. 1D basin models of the KK–109 well show that over 55% of kerogens were converted into oil in the Cretaceous (77–67 Ma). Expulsion started from the Miocene until now (22–0 Ma), consistent with 0.71–0.80 of modeled Easy%Ro and 55–80 %TR. Consequently, this project confirms the potential oil expulsion from the Chia Gara Formation, which can be a resource for upcoming hydrocarbon investigation in the Zagros basin, Iraq.

We proposed a so-called Beta Kumaraswamy Burr Type X distribution which gives the extension of the Kumaraswamy-G class of family distribution. Some properties of this proposed model were provided, like: the expansion of densi- ties and quantile function. We considered the Bayes and maximum likelihood methods to estimate the parameters and also simulate the model parameters to validate the methods based on dierent set of true values. Some real data sets were employed to show the usefulness and exibility of the model which serves as generalization to many sub-models in the elds of engineering, medical, survival and reliability analysis.

We proposed a so-called Beta Kumaraswamy Burr Type X distribution which gives the extension of the Kumaraswamy-G class of family distribution. Some properties of this proposed model were provided, like: the expansion of densities and quantile function. We considered the Bayes and maximum likelihood methods to estimate the parameters and also simulate the model parameters to validate the methods based on different set of true values. Some real data sets were employed to show the usefulness and flexibility of the model which serves as generalization to many sub-models in the field of engineering, medical, survival and reliability analysis.

The effect of SARS-CoV-2 pandemic has been subsided significantly following the rapid development of vaccine. However, patients with cancer and immunosuppressed state, who are more prone to mortality and morbidity due to this infection, were excluded from majority of the vaccine trials. Moreover, suggested dose modification for cancer and immunosuppressed patients are often not followed because of lack of awareness or unavailability of vaccination schedule. This review will try to bridge this knowledge gap by summarizing the current suggestions of dose modification of COVID-19 vaccine for patients with cancer and immunosuppression.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

Customer satisfaction is the process of reaching a customer's expectations to generate delightful experiences with a product or a brand. Delight involves delivering an unforgettable experience to users by focusing on their requirements, desires, and interests. Delighting Customers is crucial for organizations’ economic growth worldwide, especially in the airline industry. This study aims to determine if safety measures, ticketing policies, and the cost of air travel impact among the airline passengers’ satisfaction post-COVID-19 in Malaysia. A research framework is designed to present an in-depth understanding of the mentioned variables. In this study, a comprehensive survey using online questionnaire was used and 388 valid responses were obtained from airline passengers in Malaysia. Data were analyzed by employing data reduction technique and multivariate data analysis. The results revealed that safety appears to be the most essential aspect of airline customer satisfaction among Malaysians, while cost is perceived as a significant factor. Moreover, as the cost of living rose because of the pandemic, many of the income earners in the lower category are less inclined to take vacations. In a nutshell, the study recommends that airlines implement a conscious practice that contributes to the happiness of passengers, which in turn increases profitability and ensures sustainable growth of the airlines.

Regarding landscape preferences for highways, there is a dynamic interaction between users and the variety of natural and cultural landscape elements along the roadside, reflecting a balance between the highway and the natural environment. However, the rapid pace of urbanization has accelerated the development of highways, leading to the neglect or destruction of valuable landscapes. This highlights the need for visual preference assessments to protect aesthetic and environmental values. Currently, there is a lack of comprehensive criteria for assessing the visual preference of highway landscapes. Therefore, this study aims to review existing literature and establish complete assessment criteria. This study conducted a systematic literature review by searching for keywords in three databases: Web of Science, Scopus, and Google Scholar. The review included 22 papers published between 2013 and 2023 that met the criteria. An additional four relevant papers were included through a “snowballing” approach to supplement the research and results. The results of the study focused on the relationships between highway landscapes and users, user preferences, preference methods, and related variables. These inter-established relationships were used to complete an assessment framework, which establishes a basic reference standard for professionals.

Corporate identity has played a vital role in the Halal industry to create a strong foundation for its reputation in the long run. This paper used two modeling analyses for two different data. The first analysis aims to predict the relationship between Corporate Identity Management between Internal Brand and Employee Brand Support (consequence) mediated by CIM using partial-least squares-structural equation modeling (PLS-SEM). A total of 206 employees from Malaysia’s Halal food SMEs took part in the survey. The second analysis to identify topic proportions patterns using the topic modeling approach on Halal brand identity Machine learning approach of knowledge mining was applied for this analysis. Metadata of 1,091 articles were mined from the Scopus database on Halal studies across all social sciences fields. The result revealed that there was a partial relationship between Internal Brand (antecedent) and Employee Brand Support (consequence) mediated by CIM. This finding was supported by the identified topic proportions patterns from the topic modeling approach that pointed out a weak topic proportion on the Halal brand identity discussion globally, interestingly the result also found that the Halal brand identity discussion involving the Halal food industry is almost non-existed in Malaysia’s Halal food SMEs. The contributions of this paper were apparent in three major areas which are methodology, theoretical and future suggestions. The utilization of two different model analyses was able to confirm the consistency of the major findings with the literature review which opens up more possibilities for future researchers.

Virtual Histology- Intravascular Ultrasound (VH-IVUS) image is an available method for visualizing plaque component to detect thin cap fibroatheroma. Nevertheless, this imaging modality has considerable limitations to extract the plaque component features and identifying the TCFA plaque. The aim of this paper is to improve the identification of TCFA using fusion of IVUS and VH-IVUS images. In order to generate the automatic technique for reducing the human interaction, a new method namely Active Contour based Plaque Border Detection (ACPB) is proposed. In order to perform the pixel wise classification, hybrid of K-means algorithm with Particle Swarm Optimization and Plaque based Minimum Euclidean Distance (KMPSO-PMED) method is presented to classify the plaque region as well. Moreover, to obtain more significant information of imaging modalities, fusion of two different images consisting of VH-IVUS and IVUS is performed. Therefore, geometric features are extracted from the plaque region and combine with IVUS features. Furthermore, different group of plaque features are divided by means of the histopathological studies. SVM classifiers is applied to detect the TCFA and non-TCFA plaques. The proposed method is applied on 566 in-vivo IVUS and their matching VH-IVUS images obtained from 9 patients. The best result of SVM illustrates the accuracy rates of 99.41% for classification of TCFA plaque. The results prove that the highest accuracy is achieved by integrated features of IVUS and VH-IVUS images.

In bone tissue engineering, ceramics have been the choice due to their excellent biological properties. But the paradigm changed with the discovery of bioactive glasses (BGs) in 1969 by Larry Hench and co-workers, due to their ability to bond to living tissues through the formation of an interfacial bone-like hydroxyapatite layer when the bioglass was put in contact with biological fluids in vivo. Among a number of tested compositions, the one exhibiting the highest bioactivity index is the well-known trademarked 45S5 Bioglass®. The topic received increasing attention particularly after 1985 when this material entered in the market of biomedical devices, inspiring many other investigations aiming at further exploring the in vitro and in vivo performances of this BG, or developing other related BG compositions. The research efforts gradually revealed a number of shortcomings of 45S5 Bioglass®, mostly derived from its high sodium content, initially intended to decrease the melting temperature and accelerating the degradation of the silicate network over time. But the extensive release of sodium from 45S5 Bioglass® in the biological fluids creates a high pH cytotoxic environment. Other serious drawbacks include a fast degradation rate, and a poor sintering ability, which hinders the reliable fabrication of porous scaffolds. Therefore, sol-gel was regarded as an attractive alternative to prepare alkali-free BG compositions. The process uses inorganic and/or organic precursors, which undergo hydrolysis and condensation at room-temperature, being less costly. When properly conducted, the sol-gel process might result in amorphous structures with all the components intimately mixed at the atomic scale. Moreover, developing new better performing materials for bone tissue engineering is a growing concern, as the ageing of the world’s population leads to lower bone density and osteoporosis. This work describes the sol-gel synthesis of a novel quaternary silicate-based BG with the composition 60 SiO2 – 34 CaO – 4 MgO – 2 P2O5 (mol%) was prepared using acidified distilled water as single solvent. By controlling the kinetics of the hydrolysis and condensation steps, an amorphous glass structure could be obtained. The results of XRD of samples calcined within the temperature range from 600-900 ºC demonstrated that amorphous nature was maintained until 800 ºC, followed by partial crystallization at 900 ºC. The specific surface area, an important factor in osteoconduction, was also evaluated over different temperatures, ranging from 160.6 ± 0.8 m2/g at 600 ºC down to 2.2 ± 0.1 m2/g at 900 ºC, being accompanied consistent changes in average pore size and agreeing pore size distribution. The immersion of the BG particles in simulated body fluid (SBF) led to the formation of an extensive apatite layer on its surface. These overall results indicate the proposed material is very promising for biomedical applications in bone regeneration and tissue engineering.

The liver performs a fundamental role in the regulation of diverse physiological processes. Despite enormous advances in modern medicine, there are no completely effective drugs that stimulate hepatic function, offer complete protection to the organ, or aid in regenerating hepatic cells. Thus, it is necessary to identify alternative plant-origin pharmaceuticals more effective and less toxic for the treatment of hepatic diseases. The aim of this research was to establish the chemical composition of the American cranberry (Oxycoccus macrocarpus) leaves extract and its aminoacids preparations as well as their hepatoprotective activity. 19 phenolic compounds (8 flavonoids (flavones and flavonols), 4 anthocyanins, 2 catechins, and 3 hydroxycinnamic acids) and main amino acids (valine, arginine, glycine, histidine, aspartic acid, and taurine) were identified and quantified in the American cranberry (O. macrocarpus) leaves extract and its 7 aminoacids preparations. The therapeutic and prophylactic consumption of the American cranberry leaves extracts led to a decrease in the intensity of the lipid peroxidation process compared to the control pathology group in the experiment of acute toxic damage to the liver by tetrachloromethane on rats. The most pronounced hepatoprotective activity was established for the American cranberry leaves extracts’ preparations with arginine and valine.

Exploring new approaches to innovating higher vocational education is a worldwide pursuit driven by the increasing demand for graduates equipped with competencies. This study investigated how Outcomes-Based Education (OBE) influences the attainment of graduate competence (AGC) in China’s higher vocational education, using the theory of Constructive Alignment (CA) as its foundation. The OBE framework incorporates intended learning outcomes (ILOs), project-based learning (PjBL), assessment strategies (ASs), and AGC. The study tested the model by assessing the impact of ILOs, PjBL, and ASs on AGC, respectively and sequentially. Surveys were administered to 320 CBEC learners in April 2024, resulting in 301 usable responses. Data were analyzed using structural equation modeling (SEM) with SPSS 23.0 and AMOS 24.0. Results indicated that PjBL and ASs were directly and positively related to graduate competency attainment, while ILOs were indirectly associated with graduate competence through the mediating roles of PjBL and ASs. The most substantial mediating effect between ILOs and graduate competence was ASs, followed by PjBL, and then, the chain mediating effect of PjBL and ASs. These findings enhance the theoretical understanding of OBE and provide detailed procedures for tracking and enhancing sustainability in higher vocational education. Beneficiaries include educators, policymakers, and accreditation bodies.

The most modern technique utilized to create intricate and complexly manufactured parts for a variety of applications is called additive manufacturing (AM). Fused deposition modeling (FDM) has received the greatest attention in the development and manufacturing sectors. The main objective of this study was to investigate how printing factors affected the mechanical characteristics of printed samples. Samples were produced using an FDM 3D printer in compliance with ASTM D638 using a variety of input settings, including orientation, layer thickness, speed, and infill pattern. On the printed samples, tensile tests and morphological analysis using a scanning electron microscope (SEM) were done. The findings of this study demonstrate that factors including layer thickness, printing speed, and orientation significantly affect the tensile strength of ABS printed samples. Discovering the process settings that could lead to superior mechanical and physical characteristics would undoubtedly assist designers and manufacturers worldwide as the FDM 3D printer becomes more and more crucial in manufacturing engineering parts.

The global spread of multidrug-resistant (MDR) microbial infections is currently one of the most severe risks to global public health, with 10 million fatalities expected by 2050 unless action is taken. Nanotechnology has revolutionized science and medicine. The reliance on nanotechnology is growing. Nanoparticles have distinct properties that improve biological, chemical, and physical properties studied for various uses. A significant area of attention in the synthesis of nanoscale modulators is the utilization of crude formulations, retro-synthesized, and pure chemicals, mainly from herbal sources, with fewer adverse effects. Green chemistry has devised a tangential technique for synthesizing metals and metal oxides to produce nanoparticles. Plant extracts (leaves, stems, and shoots) and microorganisms (bacteria, fungus, and yeast) are used as reducing intermediates to make nanoparticles. Studies in microbiology have shown that nanoparticles kill bacteria, fungi, viruses, and protozoa. These green nanoparticles contain antibacterial, antifungal, and anti-inflammatory effects. Most nanoparticles have high antibacterial properties, indicating they may be used to combat diseases and biological contaminants. These nanoparticles have antibacterial action against pathogenic microorganisms that cause serious illnesses, including multidrug-resistant pathogens. The current research will pave the way for future applications and improved methods for producing nanoparticles, paving the way for an innovative route in nano-life sciences with widespread recognition.