Biomedical implants are the need of this era due to the increase in number of accidents and follow-up surgeries. Different types of bone diseases such as osteoarthritis, osteomalacia, bone cancer, etc. are increasing globally. Mesoporous bioactive glass nanoparticles (MBGNs) are used in biomedical devices due to their osteointegration and bioactive properties. In this study, silver (Ag) and strontium (Sr) doped mesoporous bioactive glass nanoparticles (Ag-Sr MBGNs) were prepared by a modified Stöber process. In this method, Ag+ & Sr2+ were co-substituted in pure MBGNs to harvest the antibacterial properties of Ag ions, as well as pro-osteogenic potential of Sr2 ions. The effect of the two ion concentration on morphology, surface charge, composition, antibacterial ability, and in-vitro bioactivity was studied. Scanning electron microscopy (SEM), X-Ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) confirmed the doping of Sr and Ag in MBGNs. SEM and EDX analysis confirmed the spherical morphology and typical composition of MBGNs, respectively. The Ag-Sr MBGNs showed a strong antibacterial effect against Staphylococcus carnosus and Escherichia coli bacteria determined via turbidity and disc diffusion method. Moreover, the synthesized Ag-Sr MBGNs develop apatite-like crystals upon immersion in simulated body fluid (SBF), which suggested that the addition of Sr improved in-vitro bioactivity. The Ag-Sr MBGNs synthesize in this study can be used for the preparation of scaffolds or as a filler material in the composite coatings for bone tissue engineering.

Globally, the fuel demand is increasing rapidly and the conventional method to produce fuel is toxic which causes environmental degradation and climate crisis. Therefore, biodiesel emerges as the substitute to overcome the conventional fuel problems because biodiesel is renewable and non-toxic. Biodiesel synthesis is the process of using fats and oils to produce biodiesel ester and glycerol. Biodiesel can be produced using edible and non-edible feedstock but using the edible feedstocks problems like fuel vs food, nutritional value and economic considerations were raised. Therefore, non-edible feedstocks are being used to overcome problems arising from edible feedstock. As non-edible feedstocks can easily be grown anywhere on land, doesn’t cause imbalance to food economy and has low cost. Many non-consumable seeds like Mahua, Jatropha, Castor, Neem etc. are used to produce biodiesel. Now a days, researchers are using nanoparticles to enhance the stability, quality, and properties of biodiesel. In future, researchers can use algae and microbial oils for production of biodiesel. Research can also use biojet fuel in such a way that it reduces the carbon emission. In future, production of biodiesel can be integrated into circular economy models to reduce environmental waste and impact. In this review we will discuss the production methods for biodiesel, catalysts for biodiesel production, and non-edible feedstock properties of biodiesel.

For a considerable length of time synthetic composts are utilized to satisfy the dirt necessity of supplements and yield, however huge measure of these substance manures are hazardous for condition, advantageous microorganisms, creatures, and people also. In this way, natural inviting and savvy biofertilizers are utilized. Biofertilizer are the substances which contain microorganisms those microorganisms might be growths, microscopic organisms, and protozoa which have capacity to build ripeness of soil by Nitrogen obsession, Phosphorous solubilization, and Iron sequestration. These cycles convert insoluble type of supplements into solvent structure and make it accessible to the foundations of plant which effectively take them up and use them. There are assortment of the yields whose profitability can be expanded by applying biofertilizer, for example, rice, oat, and other grain crops. In this audit we experience the method of utilization of biofertilizers, and how the assistance the plants and in which they help.

Applications for Wireless Sensor Networks (WSNs) range from monitoring the environment to automating factories. However, sustained and effective functioning is made more difficult by Sensor Nodes (SNs) limited energy supplies in which optimization is the main issue. So with the aim of increasing the lifespan by decreasing the energy consumption of WSN, Low-Energy Adaptive Clustering Hierarchy (LEACH) protocol with Deep Learning (DL) algorithm is analyzed in this paper. LEACH is a hierarchical mechanism that elects Cluster Heads (CHs) and regularly rotates their positions in order to allocate energy use effectively by using the same amount of energy. However, Deep Learning (DL) method is used to further improve energy optimization. In many applications, the types of Deep Learning methods like Artificial Neural Networks (ANNs) have shown to be very useful. Using this method, WSNs may make more efficient decisions that reduce energy consumption. Data aggregation, duty cycling, and transmission protocols may all be optimized by Deep Learning model's ability to recognize patterns and forecast network behavior. This results in lower energy consumption, a longer lifespan for the network, and better overall performance.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

Insect herbivores have a wide range of life cycles and feeding habits, making them extremely diverse. With their host plants, they form close relationships and suppress their defense mecha-nisms. Molecular elicitors are the key bio-elements in detection and recognition of attacking enemies in tissue consumption. Insect oral secretion, frass, and fluid of egg deposition contain bio-logical active molecules called herbivore-associated elicitors (HAEs) are recognized by pattern recognition receptors (PRRs). However, in insect herbivores, little is known about the molecular basis of signal transduction and regulation of plant resistance. Many plants distinguish insect feeding from wounding by HAEs presenting in their oral secretions (OS) and induce local and systemic responses against arthropod feeding. PRRs perceive HAEs in the oral secretion of cater-pillars in a species-specific manner to elicit exclusive defense responses. HAEs-PRRs interactions induce plant resistance by reprogramming plant metabolism and transcriptional machinery. Quantitative, timely, and coordinated plant response initiate early signalling events including Ca+2, reactive oxygen species (ROS) and mitogen-activated protein kinases (MAPKs). We have discussed how early signalling cascades converge into the accumulation of phytohormones that regulate down-stream special metabolites against herbivores. In this review, we have drawn a hypothetical model of PPRs-HAEs mediated induced responses in plants and discussed how PRRs-HAEs interactions based on molecular mechanism that elicit short- and long-term induced defenses in plants. The identification of plant target insect herbivore PRRs-HAEs interactions will help to explore the fundamental molecular mechanisms of host manipulation and may generate prospects to develop novel pest resistance strategies.

Mitochondria is a cellular source of energy, playing an essential role in cellular stress induced by environmental stimuli. The genetic diversity of mitochondrial genes involved in oxidative phosphorylation affects the production of cellular energy and regional adaptation to various ecological (climatic) pressures influencing amino acid sequences (variants of protein). However, a little is known about the combined effect of protein changes on cell-level metabolic alterations in simultaneous exposure to various environmental conditions, including mitochondrial dysfunction and oxidative stress induction. Present study was designed to address this issue by analyzing the mitochondrial proteins in Fasciola species including Cytochrome C oxidase (COX1, COX2, COX3 and CYTB) and NADH dehydrogenase (ND1, ND2, ND3, ND4, ND5 and ND6). Mitochondrial proteins were used for a detailed computational investigation using available standard bioinformatics tools to explore structural and functional relationships. Our analysis shows that the mitochondrial protein family of Fasciola species are extensively diversified in all species studied, showing an extending role in various biological processes The results showed that the protein of COX1 of F. hepatica, F. gigantica and F. jacksoni consist of 510, 513 and 517 amino acids respectively. The alignment of proteins showed that these proteins are conserved in the same regions at ten positions in COX and CYTB proteins while at twelve locations in NADH. Three dimensional structure of COX, CYTB and NADH proteins were compared and the differences in additional conserved and binding sites in COX and CYTB proteins as compared to NADH were found in three Fasciola species. These results, based on the amino acid diversity pattern, were used to identify sites in the enzyme and the variations in mitochondrial proteins among Fasciola species. This study provides valuable information for future experimental studies including identification of therapeutics, diagnostics and immunoprophylactic interests with novel mitochondrial proteins.

In this paper, we discuss voltage control method for buck converter operating in continuous conduction mode (CCM) using analog feedback system. The aim of this work is to control the output voltage of a buck converter during the variation in load current. This is obtained using analog feedback made with operational amplifier (Opamp). However, the same technique can be applied to other DC-DC converters (e.g boost, buck-boost, cuk converter, etc) in CCM mode, but for the purpose of analysis buck converter is chosen as an example.

Validation and verification are the critical requirements in the knowledge acquisition method for the clinical decision support system (CDSS). After acquiring the medical knowledge from diverse sources, the rigorous validation and formal verification process are required before creating the final knowledge model. Previously, we have proposed a hybrid knowledge acquisition method for acquiring medical knowledge from clinical practice guidelines (CPGs) and patient data in the Smart CDSS for treatment of oral cavity cancer. The final knowledge model was created by combining knowledge models obtained from CPGs and patient data after passing through a rigorous validation process. However, detailed analysis shows that due to lack of formal verification process, it involves various inconsistencies in knowledge relevant to the formalism of knowledge, conformance to CPGs, quality of knowledge, and complexities of knowledge acquisition artifacts. Therefore, it is required to enhance a hybrid knowledge acquisition method that thwarts the inconsistencies using formal verification. This paper presents the verification process using the Z formal method and its outcome as an enhanced acquisition method – known as the refined knowledge acquisition (ReKA) method. The ReKA method adopted verification method and explored the mechanism of theorem proving using the Z notation. It enables to identify inconsistencies in the validation process used for hybrid knowledge acquisition. Additionally, it refines the hybrid knowledge acquisition method by discovering the missing steps in the current validation process at the acquisition stage. Consequently, ReKA adds a set of nine additional criteria to be used to have a final valid refined clinical knowledge model. The criteria ensure the validity of final knowledge model concerning formalism of knowledge, conformance to GPGs, quality of the knowledge, usage of stringent conditions and treatment plans, and inconsistencies possibly resulting from the complexities. Evaluation, using four medical knowledge acquisition scenarios, shows that newly added knowledge in CDSS due to the addition of criteria by ReKA method always produces a valid knowledge model. The final knowledge model was also evaluated with 1229 oral cavity patient cases, which outperformed with an accuracy of 72.57\% compared to a similar approach with an accuracy of 69.7\%. Furthermore, ReKA method identified a set of decision paths (about 47.8%) in the existing approach, which results in a final knowledge model with low quality, non-conformed from standard CPGs. In conclusion, ReKA is formally proved method which always yields valid knowledge model having high quality, supporting local practices, and influenced from standard guidelines.

The quantile estimation of extreme wind speed is needed in various environmental fields such as climatology, design of structures, renewable energy sources and agricultural operations. These calculations are crucial for the coding of wind speed. In this study, the required wind speed series of 16 stations in Khyber Pakhtunkhwa, Pakistan, was obtained from the NASA official website and measured in meters per second (m/s) at a 10-meter distance. A Regional Frequency Analysis of 16 AMWS stations was performed using L-moments. The quantile estimates of extreme wind speed are needed for various areas of interest using Regional Frequency Analysis (RFA) and extreme value theory. These calculations are crucial for the coding of wind speed. The data was taken from the NASA official website at a 10-meter distance and measured in meter per second (m/s). A Regional Frequency Analysis of AMWS using L-moments is performed utilizing wind speed data from sixteen sites (16) in Pakistan's Khyber Pakhtunkhwa province. There are no sites that are found to be discordant. The wards method is used to construct a homogenous region and make two homogenous regions from 16 sites. The heterogeneity test justifies that both clusters are homogeneous. The most appropriate probability distribution from the Generalized Normal (GNO), Generalized Logistic (GLO), Pearson Type-3 (P3), Generalized Pareto (GPA), and Generalized Extreme Value (GEV) distributions are chosen to calculate regional quantiles. According to the L-moments diagram and Z statistics, GEV for Cluster- Ι and GLO for Cluster- ΙΙ are the best suggestions from the others. Both clusters’ robustness is measured utilizing Relative Bias (RB) and Relative Root Mean Square Error (RRMSE). Overall, GEV distribution is fit for cluster-Ι, and the GLO distribution is fit for cluster-ΙΙ. Utilizing the site mean and median as index parameters, we can also find at-site quantiles from regional quantiles. The study’s quantile estimates can be employed in codified structural designs with policy consequences.

The community of farmers in land tenure have different institutional in terms of mastery of the land. In Indonesia there were generally institutional governing the utilization of land for mastery permanently, but there were also institutional governing dominion land in turn. This research aimed to chart institutional pattern characteristic mastery of the land inheritance system passes in, andanalyzeits contribution to sustainability of agriculture in the economic, social and ecological. Research method using case studies, with unit case a subdistrict in Gowa, South Sulawesi province, Indonesia. The results showed that institutional land pattern mastery system passes the inheritance patterns of alternation that has in effect hereditary, pattern rotation established by the heir land management patterns, depending on the number of beneficiaries, as well as not having managed to land fragmentation, so the scale of farming land, conditions can be maintained , the land was slanted so given a terracing, planting process was carried out by means of mutual. Neither found that institutional land pattern mastery system passes the inheritance had been contributing the sustainability of agriculture in social and ecological, but have yet to fully contribute to the sustainability of agriculture in economy.

CoCr2O4 and doped lithium Co1-xLixCr2O4 chromate powder and nanoparticles were prepared by modified by sol-gel method. The morphological and structural properties of nano chromates were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and Photoluminescence (PL). Nanoparticles of doped lithium were synthesized by adding appropriate amount of cobalt nitrate, chromium nitrate, lithium nitrate and 1,2 Ethanediol as a complexing agent. The sample were heated at 105 ˚C for ten hours in oven to obtain dry gel. Calcination temperature for these samples was 700˚C for 3 hours in a furnace. The particle size of parent compound ranges from 4.4 nm to 11 nm, determined by SEM. The tendency of particles to form the aggregates with the increased annealing temperature was observed. The SEM and optical characterization of this compound has shown the sol gel derived material may be successfully used as an effective doped lithium cobalt ceramic pigment with controlled variation in structural and optical properties. SEM images showed that spherical like doped particle have diameter 33nm. From PL spectra Nano structure shows band gap 2.5ev and when we doped Lithium in it band gap decreases and become 1.19ev, which is associated to band gap transition.

This study uses the Scopus and Web of Science databases to review the forecast of electricity consumption from 2015 to 2024. Based on the keywords used in the article title, which are associated with electricity consumption forecasts, the study retrieved 821 docu-ments for additional analysis using various techniques. For frequency analysis, we used Mi-crosoft Excel; for data visualisation, we used VOSviewer; and for citation metrics and analysis, we used Harzing's Publish or Perish. Standard bibliometric variables, including publication growth, authorship patterns, collaboration, prolific authors, national contribution, most active institutions, favourite journals, and highly cited articles, are used in this study's reporting of the findings. Our analysis indicates that over ten years, starting in 2015, publications on the forecasting of electricity consumption have continued to increase. China was the country that contributed the most to research on electricity consumption. Most of the research publications on electricity consumption were published in the Journal of Energy.

To obtain drop-in fuel properties from non-feed biomass, we herein report the catalytic hydrotreatment of microalgae biocrude, produced from hydrothermal liquefaction (HTL) of Spirulina. Our contribution focuses on the effect of temperature, initial H2 pressure, and residence time on the removal of heteroatoms (O and N). In contrast to common hydrotreating experimental protocols at batch scale, we devised a set of two-level factorial experiments and studied the most influential parameters affecting the removal of heteroatoms. It was found that up to 350 °C, the degree of deoxygenation (de-O) is mainly driven by temperature, whereas the degree of denitrogenation (de-N) also relies on initial H2 pressure and temperature-pressure interaction.Based on this, complete deoxygenation was obtained at mild operating conditions (350 °C), reaching a concurrent 47 % denitrogenation. Moreover, three optimized experiments are reported with 100 % removal of oxygen. In addition, the analysis by GC-MS and Sim-Dis gives insight to the fuel quality. The distribution of heteroatom N in lower (<340 °C) and higher (>340 °C) fractional cuts is studied by a fractional distillation unit following ASTM D-1160. Final results show that 63-68 % of nitrogen is concentrated in higher fractional cuts.

Brazil, Russia, China, India, and the Republic of South Africa (BRICS) represent developing economies facing different energy and economic development challenges. The current study aims to forecast energy consumption in BRICS at aggregate and disaggregate levels using the annual time series data set from 1992 to 2019 and to compare results obtained from a set of models. The time-series data are from the British Petroleum (BP-2019) Statistical Review of World Energy. The forecasting methodology bases on a novel Fractional-order Grey Model (FGM) with different order parameters. This study contributes to the literature by comparing the forecasting accuracy and the forecasting ability of the FGM(1,1) with traditional ones, like standard GM(1,1) and ARIMA(1,1,1) models. Also, it illustrates the view of BRICS's nexus of energy consumption at aggregate and disaggregates levels using the latest available data set, which will provide a reliable and broader perspective. The Diebold-Mariano test results confirmed the equal predictive ability of FGM(1,1) for a specific range of order parameters and the ARIMA(1,1,1) model and the usefulness of both approaches for energy consumption efficient forecasting.

The textile processing sector is accountable for the extensive utilisation and pollution of freshwater resources. Due to heightened consumer awareness of environmental legislation regarding freshwater contamination, the textile sector is compelled to review and improve their current water consumption practices. Foan dyeing technique is a highly promising alternative that has the ability to contribute to a more sustainable future. This review paper discussed the current state of foam dyeing technology, highlighting its advantages in terms of re-duced consumption of water and energy, as well as minimal usage of dyes and chemicals compared to conventional methods. The foam configuration allows for more effective application of dyes. As a result, there is a decrease in dye consumption and a reduction in processing time. The process is environmen-tally sustainable since it significantly reduces water pollution. Furthermore, foam dyeing method consumes less energy due to its lower dying temperature need compared to conventional processing technology. Additionally, this paper highlights the continued investigation of foam dyeing on many types of textile substrates (such as fibres, yarns, and fabric) and compositions including cotton, polyester, and their mixtures. In addition, the techno-economic comparison of foam dyeing and conventional dyeing is also given. This review paper addi-tionally endorses the Sustainable Development Goals (SDG 6, clean water and sanitation) by examining the preservation of usable water and the decrease in wastewater discharge through foam dyeing technology. Lastly, the potential advantages of foam dyeing in terms of significantly reducing water consump-tion and the generation of waste in the textile industry were also addressed.

Background: Chronic Myeloid Leukemia (CML) is initiated in the bone marrow due to the chromosomal translocation t(9;22), resulting in the fusion oncogene BCR-ABL. Tyrosine kinase inhibitors (TKIs) targeting BCR-ABL have transformed fatal CML into an almost curable disease. However, TKIs lose efficacy during disease progression, and the mechanism of CML progression remains to be fully understood. Additionally, common molecular biomarkers for CML progression are lacking. Our studies previously detected ANKRD36 (c.1183_1184 delGC and c.1187_1188 dupTT) associated exclusively with advanced phase CML. However, clinical validation of this finding was pending. Therefore, this study aimed to clinically validate mutated ANKRD36 as a novel biomarker of CML progression. Materials and Methods: The study enrolled 124 patients in all phases of CML, recruited from Mayo Hospital and Hameed Latif Hospital in Lahore, Punjab, between January 2020 and September 2023. All response criteria were adopted from the European LeukemiaNet guideline 2020. Informed consent was obtained from all study subjects. The study was approved byscientific and ethical review committees of all participating centers. Sanger sequencing was employed to detect ANKRD36mutations in CML patients in accelerated phase (AP) (n=11) and blast crisis (BC) (n=10), with chronic-phase CML (CP-CML) patients as controls (n=103). Samples were processed using Big Dye Terminator Cycle Sequencing Ready Reaction kits and sequenced using ABI Prism 3730 Genetic Analyzer, and sequencing using forward and reverse primers for ANKRD36.Results: During our study, 17% of CML patients progressed to advanced phases AP-CML n= 11 (8.9%) and BC-CML n=10(8.1%). The chronic- and advanced-phase patients showed significant difference with respect to male-to-female ratio, hemoglobin level, WBC count, and platelet count. Sanger sequencing detected ANKRD36 mutations c.1183_1184 delGC and c.1187_1185 dupTT exclusively in all AP- and BC-CML patients but in none of the CP-CML patients. Nevertheless, mutations status was not associated with male-to-female ratio, hemoglobin level, WBC count, and platelet count, which makes ANKRD32 as an independent predictor of early and terminal disease progression in CML. Conclusions: The study confirms ANKRD36 as a novelgenomic biomarker for early and late CML progression. Further prospective studies should be carried out in this regard. ANKRD36, although fully uncharacterized in humans, shows the highest expression in bone marrow, particularly myeloid cells. Functional integrated genomic studies are recommended to further explore the role of ANKRD36 in the biology and pathogenesis of CML.

Objective: To investigate social, economic, and environmental contributors to quit or continue smoking and vaping during the COVID-19 pandemic. Methods: A qualitative study design was adopted to identify smokers’ beliefs in a LMIC, using a small community sample. Results: 276 participants were primarily surveyed. Motivation to continue smoking included temporary pleasurable effects, working remotely, stress or anxiety, whereas a motivator to quit smoking was the overlap with COVID-19 symptomatology. There was a rise in social awareness regarding the potential harm of smoking and vaping during the pandemic yet those participants who were younger felt they were immune from its morbid complications. Conclusions: With paradoxical associations of COVID-19 with cigarette and vape usage, it is important to pay attention to biases in data in favor of educating its users of the increased risk of severe disease.

Hepatitis B and C are major health issues in developing countries such as Pakistan and Afghan-istan. The aim of this study was to determine the prevalence and effectiveness of a screening program for hepatitis B and C in a region with no existing programs, and to estimate their prev-alence in the general population in Khyber Pakhtunkhwa Province, Pakistan, as well as in Afghan refugees or migrants. A prospective cohort study was done in the general population of Peshawar and its adjacent districts, as well as migrants from neighboring provinces of Afghani-stan, who presented to our tertiary-care health facility. A Microsoft Excel registry was created for data collection, which were analyzed using IBM SPSS via descriptive analysis, normal distribution curve histograms, and chi-squared tests. A total of 9563 individuals were screened for hepatitis (5894 males and 3669 females), including Afghan migrants in Peshawar and surrounding districts. 876 individuals tested positive for hepatitis, with 538 positive for hepatitis B (383 males and 155 females) and 330 positive for hepatitis C (198 males and 134 females). Eight individuals had a hepatitis B and C co-infection. Among the study population, the prevalence rates were 2.2% for hepatitis B and 2.3% for hepatitis C, of which the Afghan migrants accounted for 2.7% and 0.5%, respectively. According to the gender-based distribution, hepatitis B was more prevalent in males, whereas there was no significant gender-based difference for hepatitis C. Our results highlight the need for a comprehensive approach to control hepatitis B and C in Pakistan and Afghanistan. Increased awareness, improved healthcare, and preventive measures such as screening and elimination programs to prevent severe liver diseases and eradicate hepatitis are necessary.

Nowadays, more than 180 million people believe that the Holy Qur'an was sent by the Almighty Allah through Prophet Muhammad in 610-632 A.D in Mecca and Medina. However, the word Mecca (Q: 48:24) is mentioned only once in the entire Holy Qur'an, which is not related to the birth of the Prophet or any worship. Conventional Islam is mostly based on the hearsay of some Islamic narrators published in the eighth and ninth centuries. To think deeply and conduct research on the verses of the Holy Quran has been mentioned (special urge) directly and indirectly by this Holy Scripture itself many times but it would not be wrong to say that there is no scholarship on the verses of the Quran based on the research method described in the Holy Quran until the present century. Therefore, this paper has been dared to carry out by combining the methods of research followed in the Holy Quran and the academically accepted research methodology. The analysis shows that the results of almost fourteen hundred years of mythological history of conventional Islamic narrators are opposites. First of all, the proper name of the Prophet revealed by the Holy Quran is Ahmed, but Muhammad is an adjective and there are many such names. Secondly, this prophet was not born in Mecca, KSA, nor in 570/571 A.D, but in the Beqaa Valley of Lebanon, between the third and fourth centuries. Thirdly, the Muslim Hajj (pilgrimage) of Mecca is celebrated entirely according to the Lahwal Hadith (idle tales) (Q: 31:6) in the language of the Holy Quran. Originally the place designated for pilgrimage was in the Beqaa Valley, Lebanon. This article will have a double influence on the Muslim world, that is, Islamic scholars will think again deeply and research new ways of scholarship of the Holy Quran, instead of based on the hearsay of idle tales (Lahwal Hadith). On the contrary, those who are stubborn Islamic narrators, since they have already rejected the Holy Quran, will not hesitate to violently attack the researchers and they will not be positively motivated by this paper. This article specifically urges Islamic scholars to conduct in-depth studies on the most important issues of Islam using the Holy Quranic research method.

Prevalence of malnutrition among children under five is alarmingly high in Pakistan. However, there are ready-to-use therapeutic foods (RUTF) available which may be used to treat children with severe acute malnutrition (SAM). This study aims to assess the efficacy of prebiotics as a synergistic additive to RUTF to enhance blood parameters and anthropometric measurements in children with uncomplicated SAM living in Southern Punjab, Pakistan. A double-blind parallel treatment randomized controlled trial was conducted on 204 children aged between 6-59 months. Participants were randomized and allocated to the placebo (n=102) and experimental arms (n=102) at a 1:1 ratio. One group of children were provided RUTF and 4 g prebiotics, while the other group were given RUTF and starch as a placebo. Participants recruited for both arms were given treatment for eight weeks, and then their biochemical and anthropometric outcomes were evaluated. A substantial difference between the mean weight, mid upper arm circumference, haemoglobin, haematocrit, platelet count, mean corpuscular volume, mean corpuscular haemoglobin, and albumin was revealed. Conclusively, supplementation with RUTF and prebiotics has proven to be an efficient, effective and safe therapy for children suffering from SAM to improve their growth and development indicators and reduce the dangers of malnutrition in comparison to RUTF alone.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

In archaea, the interaction of HerA helicase and NurA nuclease is required for 3' end resection during DNA double-stranded break repair, and its disruption results in unfaithful DNA repair. Interactions transpire by the four conserved domains, including the N-terminal HAS domain (HerA-ATP synthase), which serves as a binding site for the exonuclease NurA. As a HerA hexamer between its two subunits, the conserved C-terminal brace extension functions as an adjacent brace. DBD serves as a location for DNA binding, which causes the DNA strands to be propelled into the HerA pocket to begin unwinding. The putative pore entrance is made up of four helix coils, which provide a suitable charged surface for guiding DNA into the pore. The crystal structure of the complex HerA-NurA allows for the identification of key residues for protein-protein interaction. This allows us to predict that most archaeal HerA orthologs will be able to interact with one another. Archaeal HerA is a homo-hexameric assembly featuring a DNA-binding domain that is conserved. It also features distinctive ATP and NurA binding domains. Following the structure and sequence conservation criteria, we find one HerA ortholog in Pyrobaculum calidifontis and multiple HerA paralogs, but the role of none is established yet.Interestingly, orthologous HerA is part of an Mre11-Rad50 gene neighborhood while paralogous HerA is not, which could be misleading. As a result, it sought to describe the criteria that may be used as a possible fingerprint for identifying orthologous genes, as well as the cloning procedures and tactics that would aid in the confirmation of the HerA helicase in P. calidifontis. Their confirmation is based on PCR cloning and characterization following HerA construct creation.

The aim of the paper is to identify the most likely factors that determine the demand for Renewa-ble Energy Consumption (R.E.C.) in European countries. Although in Europe a high environmen-tal awareness is omnipresent, countries differ in scope and share of R.E.C. due to historical ener-getic policies and dependencies, investments into renewable and traditional energetic sectors, R&D development, structural changes required by energetic policy change, and many other fac-tors. The study refers to a set of macroeconomic, institutional, and social factors affecting energetic renewable policy and R.E.C. in selected European countries in two points of time: i.e., before and after the Paris Agreement. The Bayesian Average Classical Estimates (BACE) is applied to indicate the most likely factors affecting R.E.C. in 2015 and 2018. The comparison of the results reveals that the G.D.P. level, nuclear and hydro energy consumption were the determinants significant in both analyzed years. Furthermore, it became clear that in 2015 the R.E.C. depended strongly on the energy consumption structure, while in 2018, the foreign direct investment and trade openness played their role in increasing renewable energy consumption. The direction of changes is positive and complies with sustainable development goals (S.D.G.s).

Cotton (Gossypium spp.) is a major source of natural fiber and an important cash crop. The cotton growth habit and architecture determine its productivity and influence management strategies for commercial production. The GATA transcription factors (TFs) control various developmental processes in plants, such as flower, bract and embryo development, and petal differentiation. As stable transformation is still a bottleneck in many plant species, TRV-VIGS was used to manipulate gene expression in different plants, including Gossypium hirsutum L. In this study, we undertook the TRV-based VIGS to functionally characterize two candidate genes, Gohir.D05G103700 and Gohir.D12G153600, identified through the expression QTL analysis for five floral induction and meristem identity genes using the upland cotton mini-core collection. Virus-induced silencing of the Gohir.D05G103700 gene resulted in up to a 1.4-fold reduction in the transcript level in two inoculated plants, G3 and G4, and Gohir.D12G153600 gene resulted in up to a 2.3-fold reduction in transcript level in a single inoculated plant P05 relative to the mock-treated plant. The TRV2-Gohir.D05G103700 inoculated plants precisely G3 and G4 also exhibited loss of the supernumerary (fourth) floral bract in the squares, whereas the TRV2-Gohir.D12G153600 inoculated plants did not show any observable phenotypic change relative to the mock-treated plants.  Altogether, this study suggested that TRV-VIGS can be used to characterize genes in cotton relatively rapidly and the cotton Gohir.D05G103700 gene is a positive regulator of the indeterminate growth habit in cotton, which could be manipulated to obtain a cotton plant with architecture best suited for the cultivation area.

Background: Women in rural districts of Pakistan face numerous barriers to healthcare, rendering gender-responsive health programming important, including for Tuberculosis (TB). This study was conducted to assess the general understanding of TB and of access to healthcare for women, as a first step towards implementation of a gender responsive TB programme in TandoAllayar, a rural district of Pakistan. Methods: A total of 36 participants were interviewed. The focus group discussion guide comprised of questions on: (1) family/household dynamics (2) community norms (3) healthcare system (4) women’s access to healthcare (5) TB Awareness;, and (6) women’s access to TB Care. Results: Limited autonomy in household financial decision-making, disapproval of unassisted travel, long travel time, lack of prioritization of spending on women’s health and inadequate presence of female health providers, were identified as barriers to access of healthcare for women, higher in younger women. Facilitators to access of TB care included a reported lack of TB-related stigma, moderate knowledge about TB disease, and broad understanding of tuberculosis as a curable disease. Other suggested facilitators include health facilities closer to the villages and the availability of higher quality services. Conclusion: Significant barriers are faced by women in access to TB care in rural districts of Pakistan. Programme implementers in high burden countries, should shift towards improved gender-responsive TB programming.

This study aims to explore the phenomenon of hadith distortion in hadith literature and analyze its impact on contemporary hadith studies. The intended hadith distortion here refers to the alteration or falsification of hadith narratives that can threaten the integrity and authenticity of sacred texts as sources of Islamic teaching. This article identifies the factors contributing to hadith distortion and its serious consequences in contemporary hadith studies.

Keeping in mind the increasing trend and need for serious games in science education, we have done a systematic literature review. These papers show the trends and patterns of research carried out in this field from the year 2011 to 2020. Specifically, we investigated country-wise concentration and the most common evaluation methods. Literature is reviewed from IEEEexplore, Springer, and Scopus. Moreover, we discussed the role of Augmented Reality(AR) games in teaching physics. Lastly, we have discussed the positive and negative aspects of serious games in science education in particular, and the trend of using serious games in the past decade in education in general.

LIFI was first introduce by Professor Harald Haas on July 2011. Light fidelity (LI-FI) may be a technology which uses light as a medium to travel from one place to a different. It uses Light like Light Emitting Diode (LED) visible radiation Communication (VLC) for data Transferring and Internet connection. LIFI may be a technique which uses light as a medium because it uses light to travel it's 20 times faster than any WIFI within the world. during this paper we speak about things like what's LIFI and the way it's better then WIFI why we want LIFI and What changes did bring LIFI in our Future LIFI. How it'll make IOT devices far better than before The Technique to implement LIFI and also the problem we face of implementation of LIFI

Bacterial infections are world-wide problem and resistant bacteria is increasing globally that lead to treatments failure. Thus, it is important to find new techniques that are effective for the treatment antibiotic-resistant microorganisms. Green medicine used for the medication of different bacterial infection. Therefore , the study aimed to evaluate the immunomodulatory activity of essential fatty acid semi carbazide (EFASC) compounds extracted from flaxseed to eradicate resistance pathogens . Crud extracts of Linum usitatissimum was extracted by hexane for extraction of EFASC. The results of LD₅₀ appear that a live suspension of E.coli was 0.49×10⁷ ,while HK E.coli was 10⁸ , 125 mg /ml were the optimum dose in stimulate immune response of EFASC which gave maximum dose of total WBC , Neutrophil and Monocyte count. The immunomodulatory activity appear that E.coli + EFASC released moderate levels of IL-4 . HK E.coli release higher IL-4 lead to increase the hypersensitivity and hyper responses of immune system. HK + EFASC immunogen revealed moderate increased in IL-12 mean level 0.99 pg /ml, HK bacteria recorded 1.49 pg/ml, while the mean of EFASC revealed no significant different compare with control. An effective protection was observed in immunized groups with HK E.coli and EFASC challenged with 100 of LD50 of a live E.coli.

The purpose of this paper is to describe a feature selection algorithm and its application to enhance the accuracy of the reconstruction of phylogenetic trees by improving the efficiency of tree construction. Applying machine learning models for Arabic and Aramaic scripts such as Deep Neural Networks (DNN), Support Vector Machines (SVM) and Random Forests (RF) each model was used to compare the phylogenies. The methodology was utilized with a dataset containing Arabic and Aramaic scripts, demonstrating its relevance in a range of phylogenetic analyses. Results emphasize the essential role of feature selection by DNNs is outperforming other models in terms of Area Under the Curve (AUC) and Equal Error Rate (EER) across various datasets and fold sizes. Additionally, SVM and RF models show important understandings, advantages and limits of each approach within the context of phylogenetic analysis. This method not only simplifies the tree structures but also enhances their Consistency Index. Therefore offering a robust framework for evolutionary studies. The findings highlight the applications of machine learning in phylogenetics suggesting a path toward accurate and efficient evolutionary analyses and adding a deeper understanding of evolutionary relationships.

Dalbergia sissoo (shisham), an important timber yielding multipurpose tree species of the Indian subcontinent, has been afflicted with large scale mortality due to wilt in natural forests and plantations, causing huge economic losses. Fusarium solani f. sp. dalbergiae (Fsd) has been identified as one of the causal organisms for wilt disease in D. sissoo. Present study comprises in vitro screening of ten selected genotypes of D. sissoo against two strains of Fsd in a dual culture set up under axenic condition. Callus and plantlets of ten genotypes of host plant were multiplied in vitro and were inoculated with conidial suspension of two strains of Fsd at three concentrations; 1× 10¹, 1× 10³, and 1× 10⁵ conidia/ml. Gnotobiotic evaluation of dual culture set up shows variations among D. sissoo genotypes in their response towards in vitro Fsd infection; and two genotypes (14 and 66) exhibited resistance against the pathogen strains. Callus of genotypes 14 and 66 significantly restricted the fungal mycelium growth whereas callus of remaining eight genotypes were completely infested by Fsd mycelium within 9 days. Similarly, plantlets of genotype 14 and 66, had lesser disease severity and remained green, and had fewer necrotic lesions in the roots whereas plantlets of remaining eight genotypes died within 15 days.

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

Generic object detection is one of the most important and flourishing branches of computer vision and has real-life applications in our day to day life. With the exponential development of deep learning-based techniques for object detection, the performance has enhanced considerably over the last 2 decades. However, due to the data-hungry nature of deep models, they don't perform well on tasks which have very limited labeled dataset available. To handle this problem, we proposed a transfer learning-based deep learning approach for detecting multiple pigs in the indoor farm setting. The approach is based on YOLO-v2 and the initial parameters are used as the optimal starting values for train-ing the network. Compared to the original YOLO-v2, we transformed the detector to detect only one class of objects i.e. pigs and the back-ground. For training the network, the farm-specific data is annotated with the bounding boxes enclosing pigs in the top view. Experiments are performed on a different configuration of the pen in the farm and convincing results have been achieved while using a few hundred annotated frames for fine-tuning the network.

Animal behavior analysis is a crucial tasks for the industrial farming. In an indoor farm setting, extracting Key joints of animal is essential for tracking the animal for longer period of time. In this paper, we proposed a deep network that exploit transfer learning to trained the network for the pig skeleton extraction in an end to end fashion. The backbone of the architecture is based on hourglass stacked dense-net. In order to train the network, key frames are selected from the test data using K-mean sampler. In total, 9 Keypoints are annotated that gives a brief detailed behavior analysis in the farm setting. Extensive experiments are conducted and the quantitative results show that the network has the potential of increasing the tracking performance by a substantial margin.

Infertility affects approximately 15% of couples worldwide, an estimated 30% of which is related to male factor infertility. Application of low level laser therapy (LLLT) to improve fertility status is a rapidly growing discipline in medicine. Laser therapy triggers a variety of biological processes through interaction with primary cellular photoacceptors. The present review aims at evaluating the literature available in the MEDLINE/ PubMed on cellular and molecular mechanisms of photobiomodulation in the domains of reproductive and veterinary medicine. We primarily focused on the clinical application of laser treatment on seminal quality, in particular its role in promoting spermatozoa motility, as well as the role of phototherapy in modulating assisted reproduction (ART). Additionally, we investigated the strength of evidence in support of the positive impact of photobiomodulation on facilitating ART.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

Recent progress in microfabrication technique allowed the rapid development of neural implants. They are getting categorized as effective tools for clinical practice, especially to treat traumatic and neurodegenerative disorders. Microelectrode arrays already have been used in numerous neural interface devices. Basically, almost all neural implants have been developed based on BCI (Brain Computer Interface) system. When BCI system falls under invasive technique, it is referred as BMI or Brain Machine Interface. BMIs hold promises for neurorehabilitation of motor and sensory function, cognitive state evaluation and treatment of neurological chaos. A directed overview of the field of neural implants is discussed in this article. The aim of this review is to give a brief introduction of neural prosthetics as well as their exciting applications in treating neurological disorders and a deep discussion on their functionality are mentioned. BCI system and their different types, their functionality, their pros and cons, how other neural implants developed, and their present status have been covered. Different possibilities and possible future of deep brain stimulation (DBS), Neuralink, motor and sensory neural prosthetics are further discussed.

In this study, we present different methods of estimating fuzzy reliability of a two-parameter Rayleigh distribution via the maximum likelihood estimator, median first-order statistics estimator, quartile estimator, L-moment estimator, and mixed Thompson-type estimator. The mean-square error MSE as a measurement for comparing the considered methods using simulation through different values for the parameters and unalike sample sizes is used. The results of simulation show that the fuzziness values are better than the real values for all sample sizes, as well as the fuzzy reliability at the estimation of the Maximum

This research aims to identify the role of the Dyson model for strategic development in achieving strategic success, and the starting point of the research was the following main question: What is the role of the Dyson model in achieving success?The research was applied in the field in the departments of the Baghdad Municipality, where the examination list was relied upon, which included a set of questions that the senior and middle leaders in the Baghdad Municipality answered, and it was the main means by which the information related to the field of research was collected, and the checklist included two variables and three dimensions From each variable, as each dimension included four questions that express indicators that revolve around one of the research hypotheses, and the case study methodology was used, which defined its path and steps, collected and analyzed field data, and linked it to its theoretical framework, in order to reach To achieve the goal of completing this research, and through analyzing, interpreting and discussing the results, the most important results were drawn up: It was found that the principle of motivation within the departments of Baghdad Municipality does not exist and this affects the employees who do not receive it from the higher leaders in their departments, and this shows that the leaderships in The Municipality of Baghdad do not have the skills and experience. Baghdad Municipality seeks to work alone and not to involve employees who have experiences and skills and strive to achieve development in their departments, and this is what the community members expressed. Among them and poor business completion in their departments.

In this work, PMMA(Poly methyl methacrylate) microfluidic system was used as a micro-reactor for urea hydrolysis by urease enzyme with use conductivity principle and utilize sound level meter(SLM) App in smartphone as a novel detector by considering the peak height in the App as an indicate for urea concentration. the advantage of use small volume and how the reaction carried on in the microfluidic system with simple and low cost are discussed, and the results were analyzed and statically determine. The linearity, detection limit (3×noise )and Correlation Coefficient, 62.5-500 ppm, 31.25 ppm and 0.992 respectively also, recovery studied were between(98.5-100.13%).

4-component relativistic atomic and molecular calculations are typically performed within the no-pair approximation where negative-energy solutions are discarded, hence the symmetry between electronic and positronic solutions is not considered. These states are however needed in QED calculations, where furthermore charge conjugation symmetry becomes an issue. In this work we shall discuss the realization of charge conjugation symmetry of the Dirac equation in a central field within the finite basis approximation. Three schemes for basis set construction are considered: restricted, inverse and dual kinetic balance. We find that charge conjugation symmetry can be realized within the restricted and inverse kinetic balance prescriptions, but only with a special form of basis functions that does not obey the right boundary conditions of the radial wavefunctions. The dual kinetic balance prescription is on the other hand compatible with charge conjugation symmetry without restricting the form of the radial basis functions. However, since charge conjugation relates solutions of opposite value of the quantum number κ, this requires the use of basis sets chosen according to total angular momentum j rather than orbital angular momentum ` . As a special case, we consider the free-particle Dirac equation, where the solutions of opposite sign of energy are related by charge conjugation symmetry. We note that there is additional symmetry in those solutions of the same value of κ come in pairs of opposite energy.

In this paper, it is proved that s-iteration with error and Picard-Mann iteration with error iterative processes converge strongly to the unique fixed point of Lipschitzian strongly pseudo-contractive map. This convergence is almost -stable and -stable. Applications of these results to the operator equations, where is a strongly accretive and accretive mappings of into itself.

Currently, the use of recycled waste plastic in road construction is not just considered ecofriendly but also considered advantageous for improving road performance over time. This research explores using recycled plastic bags, made of low-density polyethylene (LDPE), in asphalt mixtures to improve road performance and manage waste. The study aims to assess the effects of incorporating different amounts of shredded waste plastic into asphalt mixes and determine the optimal percentage. The aggregate used was obtained from Sargodha quarry Pakistan and asphalt used was 60/70 grade obtained from national refinery limited Pakistan. Using the Marshall mix design, the optimum bitumen content (OBC) was found to be 4.5% of the asphalt mix weight. Thirty samples were tested with waste plastic proportions of 6%, 8%, 10%, 12%, and 14% of OBC weight, along with a standard mix. Tests on stability, bulk density, flow, and air voids showed that a 10% plastic content significantly enhances asphalt performance, increasing stability by around 25%. The study recommends using 10% plastic by OBC weight in asphalt mixes for better performance and suggests further research on optimal incorporation techniques of waste materials in asphalt mixtures.

Background: Video assisted thoracoscopic surgery (VATS) has become the recommended approach for treatment of resectable lung cancer. However, no large randomized clinical trial has been conducted formally comparing surgical resections completed by VATS to those done by open thoracotomy (OT) in low volume centers. The current study sought to assess differences in recurrence-free survival (RFS), overall survival (OS), positive margins and postoperative length of stay (LOS) between VATS and OT lobectomies in our center. Method: A single institution retrospective chart review from May 2005 through May 2015 was conducted. All patients diagnosed with stage I through III lung cancer who underwent surgical resection were selected. Patient and tumor characteristics recorded included age at diagnosis, sex, tobacco use, tumor location (side and lobe), stage, size and receipt of chemotherapy or radiotherapy. Chis-square and Wilcoxon-Mann-Whitney tests were used to compare demographics, tumor characteristics and LOS. Multiple logistic and Cox regression analyses were used to compute relative risk (RR) for positive margins and mortality hazard ratios along with 95 percent confidence intervals (95%CI), respectively. Results: Of the 235 patients, 101 subjects had VATS while OT was performed in 134 patients. Age at diagnosis, sex, tobacco use, tumor location, and size were comparable for VATS and OT. No significant difference was observed in the relative risk of positive margins for VATS versus OT, RR = 0.56 (95%CI = 0.26, 1.05). However, VATS had shorter median LOS compared to OT (4 vs. 6 days, respectively), p = 0.002. A comparison of VATS versus OT showed no significant difference in the risk of recurrence, HR = 1.21 (95%CI = 0.74, 2.00), or death, HR = 1.34 (95%CI = 0.88, 2.06), in the intent-to-treat population. Similarly, no significant differences in recurrence or mortality risk were observed between VATS versus OT for analyses conducted separately for each cancer stage group or those limited to patients with negative margins. Conclusion: Our study indicates that compared to OT, VATS leads to shorter LOS while achieving comparable margins status, recurrence-free and overall survival regardless of tumor stage at diagnosis.

This paper utilizes a life cycle assessment to evaluate the energy resources and environmental impacts of three heating systems. In the first step, life cycle assessments (LCAs) are prepared for the renewable, conventional, and combined systems. The system boundary of the LCA method is "cradle to gate," which means it includes the entire life cycle of a product or process. This includes energy supply, transport, energy generation, and operational energy use. The system scenarios were compared based on ecological and energy loads in the second step. Primary energy, resources, emissions, and environmental potentials are calculated for the system scenarios using the life cycle assessment methods CML 2016 and ReCiPe 2016. Finally, models for environmental reliability and complex decision-support tools have been developed. This work addresses two main questions: how to characterize the environmental and energy impacts of the systems under study, and what is the optimal scenario for the system? The research results show that the gas boiler system has a greater environmental impact. The most significant differences between the systems relate to the degrada-tion of abiotic fossil fuels when using a gas boiler and the process of acidification when using an electric heat pump. The results can be used to develop sustainable heating systems with reduced environmental impacts and enhanced energy efficiency.

Bioprinting is a relatively new yet evolving technique predominantly used in regenerative medicine and tissue engineering. 3D bioprinting techniques combine the advantages of creating Extracellular Matrix (ECM) like environments for cells and computer-aided tailoring of predetermined tissue shapes and structures. The essential application of bioprinting is for the regeneration or restoration of damaged and injured tissues by producing implantable tissues and organs. The capability of bioprinting is yet to be fully scrutinized in sectors like the patient-specific spatial distribution of cells, bio-robotics, etc. In this review, currently developed experimental systems and strategies for the bioprinting of different types of tissues as well as for drug delivery and cancer research are explored for potential applications. This review also digs into the most recent opportunities and future possibilities for the efficient implementation of bioprinting to restructure medical and technological practices.

The term Air Quality (AQ) pertains to the standard of air, which has a direct impact on the health and well-being of individuals. It is crucial to maintain high Air Quality (AQ), for better health and productivity. Though most of people spend more time indoors nowadays, it is not to be overlooked that the pollutant concentration in indoor air is directly linked to the outdoor air quality. Due to the changes in occupancy patterns, outdated maintenance of ventilation systems, and structural flaws in buildings, the indoor air is significantly polluted; pollutants emitted outdoors enter indoor air through open windows, ventilation systems and infiltration. In this paper, we have proposed a new technique, DTMCPM (discrete-time Markov chain (DTMC) model for the analysis and forecasting of AQ, using the power method). Specialized sensors and equipment to measure different pollutants, such as particulate matter, ozone, nitrogen dioxide, sulfur dioxide, benzene and toluene, are used to collect data by the Institute of Pakistan Air Quality Monitor in various cities; the data is converted to US EPA standard for all pollutant species. This data is used to calculate the transition matrix, steady-state values and mean return rate for the analysis of IAQ. The calculated and actual return rates have been compared and the proposed model is found to have a low average prediction error of 2.356%.

Since the 1980s, a growing interest in goat milk was noticed due to the nutritional values and health benefits of this milk, which resulted in increasing goat populations and milk production worldwide. This comprehensive review elaborates on goat milk composition compared to other types of milk. It is also an overview of goat milk production, properties, nourishment-value, applications in dairy products, and potential health benefits. Goat milk composition and its characteristics are slightly different from other types of milk and can be utilized to manufacture many dairy products. Fresh goat milk and goat milk products (e.g., yogurt and kefir were found to provide various potential health benefits, such as anti-inflammatory, prevent cardiovascular disease, anti-diabetic and antihypertensive, strengthen bones, boost immunity, and improve metabolism.

Abstract: The Tropical Rainfall Measuring Mission (TRMM) and then Global Precipitation Mission (GPM) are the most important and widely used data sources in the forecasting of drought, flood, and water resources management. However, since this sensor’s data is primarily used for tropical regions, it is necessary to evaluate the accuracy for optimal use of the data across varying climatic and physiographic conditions. In this study, the accuracy of the satellite data for a span of 17 years (2000-2017) for three climatic zones has been explored using synoptic ground station data. The climates include a) arid and low rainfall, b) semi-arid and low rainfall, and c) humid and high rainfall. We evaluated satellite data accuracy in drought and wet conditions based on the Standard Precipitation Index (S.P.I.) and different seasons. For available ground control stations, 13 stations were used in the humid, seven stations in a semi-arid climate, and 12 stations in the dry climate. The results show that the monthly precipitation product of GPM (IMERG product) and TRMM (TMPA/3B43 product) overestimate the rainfall. In the arid climate, the precipitation is estimated 43%, in the semi-arid environment 50%, and in the humid weather 11% more than the ground-based data on average. Therefore, to use satellite data in different climates, it is necessary to make corrections to obtain precise results. Based on 32 ground stations, the correction coefficient has a positive relationship with average precipitation and altitude and an inverse relationship with the latitude. Further in-depth investigations showed that the accuracy of satellite data in wet conditions is higher than the accuracy of normal circumstances, and the accuracy of normal conditions is more accurate than drought conditions. Besides, the accuracy of satellite data in wet or dry conditions increases with increasing time scales. The highest accuracy was obtained for a 12-month time scale and the lowest accuracy for the 3-month time scale of drought conditions in the arid climate.

The hybrid seeds of several important crops with supreme qualities, including yield, biotic and abiotic stress tolerance, have been cultivated from decades. Thus far, a major challenge with hybrid seed, it does not hold ability to produce plants with same qualities over subsequent generations. Apomixis exist naturally an asexual mode of reproduction in flowering plants via avoiding meiosis and ultimately leads to seed production. Apomixis possess potential to preserve hybrid vigor for multiple generations for economically important plant genotypes. The evolution and genetics of asexual seed production is unclear and need much more efforts to find its genetic architecture. To fix hybrid vigor synthetic apomixis has been suggested an alternative. The development of MiMe (Mitosis instead of Meiosis) genotypes are utilized further for clonal gametes production. However, the identification and parental origin of genes responsible for synthetic apomixis are less known and need further understanding. Genome modifications utilizing genome editing technologies (GETs) like clustered regularly interspaced short palindromic repeats (CRISPR)/CRISPR-associated protein 9 (cas9) a reverse genetics tool has paved way to utilize emerging technologies in plant molecular biology. From the last decade, several genes in important crops have been successfully edited. The vast availability of GETs has made the functional genomics studies easy to conduct in crops important for food security. The disruption of expression of genes specific to egg cell MATRILINEAL (MTL) or BABY BOOM1 (BBM1) through CRISPR/Cas genome editing system can promote haploid plants. The establishment of synthetic apomixis by engineering MiMe genotype by genome editing BBM1 expression or disruption of MTL leads toward clonal seed production. In present review, we discussed the current development in plants by utilizing CRISPR/Cas9 technology and its possibility of promoting apomixis in crops to preserve hybrid vigour. In addition to this, genetics, evolution, epigenetic modifications and strategy for MiMe genotype development has been discussed in detail.

Increased construction activities in Australia have led to the generation of a massive volume of construction and demolition (C&D) waste annually. Management of this volume of waste requires an effective waste framework. The literature reported that the current Australian waste framework does not meet expectations and needs immediate improvements. This study was therefore conducted to seek the key C&D stakeholders' opinion about various issues identified in this waste stream. The specific objectives of this study are identification of the main barriers to effective C&D waste management, the impact of current regulations and opportunities to enhance the current C&D waste management system. A survey was conducted in 2019 to capture the stakeholders' perception. 132 participants from various industries and government agencies based in various Australian jurisdictions took part in the survey. The key results showed that the main barriers towards an effective management system are "overregulation, tough acceptance criteria, and increased testing requirements", "lack of local market" and "culture, poor education and low acceptance". Furthermore, a low number of participants indicated that the current legislation encourages waste recovery activities. The main areas of improvements included "providing a guideline that determines the accepted level of contamination for reusing C&D waste”, "preparation of guidelines on requirements of using recycled C&D materials in different industries" and "setting target for reduction, reusing, and recycling C&D waste". The results can inform policy development and be used as evidence for a broader discussion to solve lasting issues in C&D waste management.

The traditional standards employed for pain assessment have many limitations. One such limitation is reliability because of inter-observer variability. Therefore, there have been many approaches to automate the task of pain recognition. Recently, deep-learning methods have appeared to solve many challenges, such as feature selection and cases with a small number of data sets. This study provides a systematic review of pain-recognition systems that are based on deep-learning models for the last two years only. Furthermore, it presents the major deep-learning methods that were used in review papers. Finally, it provides a discussion of the challenges and open issues.

With the advent of digitization, the integration of advanced technologies in operations and projects across all sectors is in progress. Accordingly, efforts are being made to utilize cutting-edge technologies to improve the circularity of the built environment. This study aimed to review the existing applications and limitations of building information modeling (BIM) tools for circular economy (CE) implementation from this perspective. A literature review was conducted to provide an overview of the use of BIM tools for conducting life cycle assessments, energy analysis, waste management, and formulation of material passports for buildings. It was found that BIM tools, which are available across all life cycle phases of building, have a great potential to improve the circularity of the sector. The overview provided on the use of various BIM tools may help stakeholders of the built environment understand the role of BIM for CE adoption in the sector.

High antioxidants level in food is gradually becoming popular because of the enhanced risk of oxidative stress in humans. Bread wheat is rich in vital antioxidants but its major bioactive compounds are not available for the human. This study was conducted with the aim to enhance the phytochemical constituents and antioxidative activity of wheat grains by fermenting it with the use of Bacillus subtilis KCTC 13241. The antioxidative potential was determined by DPPH (2,2-diphenyl-1-picryl- hydrazyl) and ABTS (3-ethyl-benzothiazo- line-6-sulfonic acid) radical scavenging assay as well by the concentration of amino acids, flavonoids, minerals, carbohydrates, and phenolic compounds. Different varieties showed different free radical scavenging potential on fermentation, which was significantly high with respect to their corresponding unfermented wheat varieties. The highest potential was found in a fermented wheat variety named Namhae and this combination can be used in the pharmaceutical and food industries.

The deposition of dust particles on solar panel modules constitutes a significant challenge, leading to a potential reduction in solar cell performance. This work tackles this issue by investigating the surface modification of a layer of transparent indium tin oxide (ITO), with a detailed analysis of the influence of its characteristics via different annealing conditions/processing. The ITO layer has been studied to enhance its characteristics for dust removal applications. Of particular note is that the developed ITO layer can be applied to dust removal using electrostatic or magnetic-based approaches. Thus, the correlation between annealing gas (using Argon, Oxygen, and Nitrogen), annealing temperature, and annealing ramping rate is explored with the obtained surface topography, as well as electrical and optical properties. The developed ITO layers annealed in the Argon medium at 600°C with an annealing ramping rate of 50°C/s showed smooth surface roughness, the highest electrical conductivity, and a relatively low refractive index. Such findings can play a crucial role in the future implementation of using the enhanced ITO layer for dust mitigation in solar panels, thus improving their long-term performance.

We introduce the notion of generalized contraction on dualistic partial metric spaces. A fixed point theorem for mappings satisfying above mentioned contraction is obtained. Some consequences of our result are obtained. We construct an example to demonstrate the effectiveness of our result among the corresponding results in partial metric spaces. Our results provide substantial generalizations and improvements of several well known results existing in the comparable literature. We discuss an application of our fixed point results to show the existence of solution of functional equations.

Newcastle disease virus (NDV) causes a highly contagious and devastating disease in poultry, Newcastle disease (ND). ND causes heavy economic losses to the global poultry industry by decreasing the growth rate, decrease egg productions, mortality, and morbidity. Although, significant advances have been made in the vaccine development, but outbreaks are reported in vaccinated birds leading to overall decreased growth rate. In this study, we report the damage caused by the NDV infection in the pancreatic tissues of vaccinated as well as specific pathogen free chickens. The histopathological examination of the pancreas showed sever damage in the form of partial depletion of zymogen granules, acinar cell vacuolization, necrosis, and apoptosis, congestion in the large and small vessels, sloughing of epithelial cells of pancreatic duct, and mild perivascular edema. Increased plasma levels of corticosterone, somatostatin, were observed in NDV infected chicks at 3 and 5-day post infection (DPI). Slight decrease in the plasma concentrations of the insulin were noticed at 5 DPI. Significant changes were not observed in the plasma levels of glucagon. Furthermore, NDV infection has decreases the activity and mRNA expression of amylase, lipase, and trypsin from the pancreas. Taken together, our findings highlight that NDV induces extensive tissue damage in pancreas, decrease the activity and expression of pancreatic enzymes and increase plasma corticosterone and somatostatin.

: This study aims at exploring Turkish consumers’ behaviors toward purchasing green fashion. A mixed-methods approach was used in this study. Six experts from the main brands in the fashion industry in Türkiye were interviewed. A total of 268 questionnaires were collected from Turkish consumers, and their responses were analyzed. The theory of planned behavior (TPB) informed the theoretical framework of this study. The main components of the TPB were extended to include perceived consumer effectiveness. A thematic analysis was conducted to analyze and code the interviews. To test the hypotheses, structural equation modeling (SEM) was conducted. The findings show that the key factors of the TPB, i.e., attitudes (ATTs), subjective norms (SNs), and perceived behavioral control (PBC), as well as perceived consumer effectiveness, significantly impact the intentions of Turkish consumers to purchase sustainable fashion. However, the results highlight some inconsistencies, gaps, and barriers that discourage the purchase intentions of consumers, including a lack of information, misinformation, greenwashing, green skepticism, a lack of trust, and the high cost of sustainable fashion.

Sustainable development and education in sustainable development (ESD) are crucial and interconnected topics under wide discussion today. Young adults need to be educated in how to help bring about change. Thus, the dynamic relationship between school and home is important. In education, use could be made of English language classes, especially since English is a global language that enables access to the sustainability literature and facilitates discussion in global conferences and meetings. Consequently, English as a foreign language (EFL) students could gain confidence from being able to understand and use the terminology of, for example, sustainability. In this paper, the use of competence-based language teaching (CBLT) is proposed as a means of introducing sustainability topics into EFL writing classes at a university in Saudi Arabia. Students’ competence in sustainable development is therefore considered based on their ability to write about suggested sustainable development topics, measured on a scale for five dimensions of ESD proposed by Michelsen and Fischer (2017). The results demonstrate that the students possessed competence in sustainable development and intended to participate in its implementation. Thus, recommendations are made for the stakeholders in the education sector to include sustainable development topics as an initial offering in the curricula of various specialties using the CBLT approach.

Human papillomavirus (HPV) infections, primarily transmitted through sexual contact, have been linked to various cancers, including cervical, penile, anal, oropharynx, breast, and prostate cancers. This study presents a unique case of concurrent high-risk HPV35, HPV45, and HPV59 infections in both prostate and bladder cancer tissues from a single patient, representing the first documented instance worldwide with identical HPV types detected in two adjacent organs of the same individual. Employing a multiplex-PCR approach, gel electrophoresis, and Sanger sequencing, we confirmed the presence of these high-risk HPV types. Additionally, Western blot analysis using an HPV E7 antibody demonstrated the active expression of HPV oncoproteins in both cancer types. This discovery underscores the potential for HPV intra-organ transmission and necessitates further exploration of alternative transmission routes. The implications of our results offer new insights into the complex dynamics of HPV transmission in cancer pathogenesis.

Different materials prepared by appropriate synthesis methods and applying different post syn-thesis processes could be used as hole transport layer in perovskite solar cells. In the present work annealing was employed to enhance physical properties of copper oxide (CuO) thin films fabricated via spin coating technique and the effects of annealing on their optical, morphological, electrical and structural properties were investigated. The XRD findings revealed the polycrystalline structure with large crystallite size. Optical spectra showed larger transmission beyond the visible region, reduced absorption, and a decrease in bandgap energy from 1.93 eV to 1.81 eV. The Ag phonon modes at 299.22 and 304 cm-1 shown by the Raman shift confirmed the development of the CuO pure phase. FTIR spectra showed the Cu-O stretching band at 759, 764 and 446 cm−1. SEM revealed the agglomeration of nano crystallites with large grains on the surface. The carrier type conductivity of annealed CuO thin films was determined via two-point hot probe technique. Low resistivity values were determined via four-point probe method. These findings indicate that CuO thin films may be successfully used as a companion with an n-type layer in p-n junction solar cells, and a hole transport layer in perovskite solar cells.

Structural design optimization (SDO) plays a pivotal role in enhancing various aspects of construction projects, including design quality, cost-efficiency, safety, and structural reliability. Recent endeavors in academia and industry have sought to harness the potential of Building Information Modeling (BIM) and optimization algorithms to optimize SDO and improve design outcomes. This review paper aims to synthesize these efforts, shedding light on how SDO contributes to project coordination. Furthermore, the integration of sustainability considerations and the application of innovative technologies and optimization algorithms in SDO necessitate more interactive early-stage collaboration among project stakeholders. This study offers a comprehensive exploration of contemporary research in integrated SDO employing BIM and optimization algorithms. It commences with an exploratory investigation, employing both qualitative and quantitative analysis techniques following the PRISMA systematic review methodology. Subsequently, an open-ended opinion survey was conducted among construction industry professionals in Europe. This survey yields valuable insights into the coordination challenges and potential solutions arising from technological shifts and interoperability concerns associated with widespread SDO implementation. These preliminary steps of systematic review and industry survey furnish a robust knowledge foundation, enabling the proposal of an intelligent framework for automating early-stage sustainable structural design optimization (ESSDO) within the construction sector. The framework ESSDO addresses the challenges of fragmented collaboration between architects and structural engineers. This proposed framework seamlessly integrates with the BIM platform, i.e., Autodesk Revit for architects. It extracts crucial architectural data and transfers it to the structural design and analysis platform, i.e., Autodesk Robot Structural Analysis (RSA), for structural engineers via the visual programming tool Dynamo. Once the optimization occurs, optimal outcomes are visualized within BIM environments. This visualization elevates interactive collaborations between architects and engineers, facilitating automation throughout the workflow and smoother information exchange.

Back-care knowledge and behaviour may play a vital role in preventing musculoskeletal current and future discomfort and injuries. The aim of the current survey was to explore the level of knowledge regarding ergonomics and posture together with postural behaviour and the incidence of musculoskeletal pain (MSP) in university students in the northeast of England. A mixed methods survey was conducted on a convenience sample of 55 university students. The 32-item valid and reliable questionnaire contains questions on socio-demographics, MSP, knowledge regarding ergonomics and posture (8 closed ended and 8 open-ended items) as well as postural behaviour. Nearly 1.8%, 20% and 78.2% of the university students had poor, fair and good knowledge of ergonomics and posture respectively. Among the 37 students who carried a backpack, 51.4% were found to have poor postural behaviour, 37.8% had fair behaviour and 10.8% had good postural behaviour. Of the 18 students who did not carry a backpack, 55.6% were found to have poor postural behaviour, 27.8% had fair behaviour and 16.6% had good postural behaviour. 70.9% of the students experienced MSP with the most prevalent site of pain being the lower back region. The key themes that emerged from qualitative data (8 open-ended questions) were: “Comfortable posture”, “Correct spinal alignment”, “Spine support”, “less pain and injuries”, “Use knees not the back”, “Keep the object close to body”, “Hands on desk”, “Feet flat on floor” as well as “eyes at screen level”. The findings of this study can be used to develop targeted interventions aimed at educating university students about ergonomics and posture in order to prevent the incidence of MSP. Future research in this field with a large and more representative sample of the university students’ population is strongly recommended to fully understand their knowledge of ergonomics and posture, postural behaviour as well as incidence of MSP.

A derivative series of 3,4-dimethoxy-β-nitrostyrene were synthesized and identified including new compound 6. The effect of antimicrobial activity of 3,4-alkyloxy modification of β-nitrostyrene was investigated. A molecular docking was also performed to obtain information about their interactions with Protein Tyrosine Phosphatase 1B (PTP1B). PTP1B containing cysteine 215 and arginine 221 as essential active residues plays a key role in signaling pathways that regulate various cell functions of microorganisms, which also act as negative regulator in signaling pathways of insulin that are involved in type 2 diabetes and other metabolic diseases. Compound 5 and 6 were the most potent as fragment of PTP1B inhibitor based on molecular docking, but compound 5 was more effective against Candida albicans. These compounds interact with serine 216 and arginine 221 residues. However, further research is needed to investigate their potential medicinal use.

Background Apolipoprotein E (APOE) gene polymorphism has been implicated in the pathogenesis of various metabolic disorders, including type 2 diabetes mellitus (T2DM). Type 2 diabetes mellitus (T2DM) is a major public health concern worldwide, including in Pakistan. Cardiovascular problems linked with T2DM have a significant impact on people and society. The study's goal is to investigate the relationship between Apolipoprotein E (ApoE) genotypes, lipid profiles, and cardiovascular complications such as ischemic heart disease (IHD) and stroke. Methods: This study was carried out on 260 subjects, divided into control D1: Diabetics without cardiovascular issues. D2: Diabetics with heart disease. D3: Diabetics with stroke. D4: Diabetics with both heart disease and stroke. Anthropometric parameters (age, BMI) and risk factors (smoking, diabetes duration, hypertension) were assessed in all groups. Serum levels of TC, TG, LDL, HDL, VLDL, creatinine, BSF, and HbA1c were measured. Apolipoprotein E gene polymorphism was determined using PCR-RFLP. Results: Hypertension, BMI, and dyslipidemia, defined as elevated levels of total cholesterol, triglycerides, LDL, HDL, and VLDL, as well as uncontrolled hyperglycemia (elevated fasting blood sugar and glycated hemoglobin) in T2DM, were linked to vascular complications such as IHD and stroke. Hypertension was prevalent in 75.4% of the population, with greater rates among the elderly. Stage 2 hypertension was more prevalent in all age groups. Apolipoprotein E gene polymorphism was discovered, with genotypes 3/3, 4/4, 2/3, and 3/4 being the most prevalent. Genotype 3/4 was more common in diabetics who had IHD/stroke or both problems, whereas genotype 2/3 was linked to DM and stroke. Conclusion: It is concluded that BMI, hypertension, hyperglycemia, atherosclerosis, and dyslipidemia are linked with cardiovascular complications of type 2 diabetes. Apolipoprotein E gene polymorphism is associated with cardiovascular disease in diabetic patients by affecting the lipid profile.

The consumption and sale of fresh-cut products and salads have been growing tremendously in the present era. Therefore, the microbial safety of such products is of great concern. In the current study, a survey of general microbiological safety of fresh-cut produce and salads at quick-service restaurants (QSR) was undertaken across the Kingdom of Saudi Arabia. These findings were compared with microbiological criteria for foodstuffs by Saudi standards, metrology, and quality organization SASO-GSO-1016. Of the 82 samples of fresh-cut produce, 7% of samples were found to be unsatisfactory or beyond the acceptable limits. TPC count was unsatisfactory at 22%, coliform at 48%, and Staphylococcus aureus at 4%. For 108 samples for fresh salads, 11% of samples were found to be unsatisfactory or beyond the acceptable limits,13%, 27%, 4%, and 27% of samples showed an unsatisfactory range of TPC, coliforms, S. aureus, and Escherichia coli, respectively. The fresh-cut produce and salads were microbiologically safe in the central region compared to the eastern region followed by the western region. The relatively higher count was found in green pepper, mixed vegetables, and lettuce followed by fresh-cut onions and coleslaw salads. No Salmonella was detected in both fresh-cut produce and salads. The restaurants should be more stringent in their processing to ensure the consumer safety. Washing and sanitization of produce is the only way to reduce the diffusion of food borne pathogens.

Photonic sensors are innovative devices that leverage the principles of light-matter interaction to enable precise and efficient detection of various physical parameters. These sensors operate by exploiting the interaction between photons, the fundamental particles of light, and matter. The light propagates through an optical waveguide, and a portion of the electromagnetic field extends beyond the waveguide surface, forming the evanescent field. This evanescent field interacts with the surrounding medium, allowing for highly sensitive detection of changes in the refractive index or properties of nearby substances. The underlying concept involves the modulation of light properties, such as intensity, wavelength, or phase, when it interacts with a target substance or undergoes changes in the surrounding environment. The advancements in photonic sensor technology have paved the way for enhanced sensitivity, selectivity, and miniaturization, making them invaluable tools in diverse industries. The ability to harness light-matter interactions for sensing purposes not only facilitates highly sensitive measurements but also allows for non-intrusive and remote monitoring, contributing to the evolution of smart and connected systems. In this overview, the material platforms and waveguide structures are explored that can make highly sensitive photonic devices applied to gas and biosensing applications.

Background: One of the most common occupational health hazard and serious health concern, now a days, recognized is Musculoskeletal disorders (MSDs). The high prevalence among students and teachers is a major cause of decline in their health related quality of life and work performance. This study aimed to identify the prevalence of musculoskeletal disorders among teachers and students during online education. Methods: A cross-sectional survey was conducted among university faculty members and students who were involved in online education during COVID-19. Data collection was carried out electronically through a validated Arabic version of the Nordic Musculoskeletal Questionnaire (NMQ) which is self reported. A total of 175 respondents responded to the questionnaire (response 60%). Results: The prevalence of any part of the body was 90.3%. The commonest site of MSDs for past 12 months was the low back (65.7%), the neck (58.3%), and shoulders (57.7%). Females (80%) suffered more than males (20%). The students reported slightly higher MSDs as compared to teachers (93.1% vs 90.3). Binominal regression analysis showed association of females with low back pain “OR: 2.24 (95% CI): 1.04-4.83; p = 0.03” and neck pain “OR: 2.7 (95% CI): 1.24–5.84; p = 0.012)” while bad posture was associated with pain in upper back “OR: 3.46 (95% CI): 1.73-6.93; p = 0.001”. Conclusion: The faculty members and students are prone to high MSDs during online classes and significant measures should be taken to reduce the prevalence by addressing associated risk factors.

The most potential renewable energy source for global emissions reductions is green hydrogen production. Iraq is looking into several sources of alternative energy to lessen its dependency on fossil fuels and to considerably cut its carbon dioxide emissions. This research examined the conceptual framework for the production and consumption of green hydrogen in Iraq. On the basis of accessible official and public data from government agencies, the potential capabilities of renewable energy resources are assessed, and certain fair assumptions are also established for a full study and evaluation of a possible hydrogen production in the country. The data presented here demonstrate conclusively that the contributions of renewable energy to the production of green hydrogen are substantial, giving the country prominence in the area of green hydrogen production. A pathway for a green hydrogen economy in the country by 2050 is proposed by this research based on its analysis. It is distributed in three stages: green hydrogen as a fuel for industry; using green hydrogen for fuel cells; and hydrogen commercialization. On the other hand, the research found a number of challenges to the implementation of a green hydrogen production that can be used in Iraq and other developing countries, including technological, economic, and social problems in addition to the related policy consequences.

Cancer cachexia is a multifactorial syndrome that is identified by ongoing muscle atrophy, along with functional impairment, anorexia, weakness, fatigue, anemia, reduced tolerance to antitumor treatments. Thus, reducing the patients’ quality of life. Cachexia alone causes about 22-25% of cancer deaths. This review covers the symptoms, mediators, available treatment, and prospects of 3D bioprinting for cancer cachexia. Studies about cachexia have shown several factors that drive this disease – protein breakdown, inflammatory cytokines activation, and mitochondrial alteration. Even with proper nutrition, physical exercises, anti-inflammatory agents, chemotherapy, and grafting attempts, standard treatment has been unsuccessful for cachexia. But the use of 3D bioprinting shows much promise compared to conventional methods by attempting to fabricate 3D constructs mimicking the native muscle tissues. In this review, some 3D bioprinting techniques with their advantages and drawbacks, along with their achievements and challenges in in-vivo applications have been discussed. Constructs with neural integration or muscle-tendon units aim to repair muscle atrophy. But it is still difficult to properly bio-print these complex muscles. Although progress can be made by developing new bio-inks or 3D printers to fabricate high-resolution constructs. Using secondary data, this review study shows prospects of why 3D bioprinting can be a good alternate approach to fight cachexia.

The emerging wireless energy transfer technology enables sensor nodes to maintain perpetual operation. However, maximizing the network performance while preserving short charging delay is a great challenge. In this work, a Wireless Mobile Charger (WMC) and a Directional Charger (DC) are deployed to transmit wireless energy to the sensor node to improve the network's throughput. To the best of our knowledge, this is the first work to optimize the data sensing rate and charging delay by joint scheduling of MC and DC. We prove we can transmit maximum energy to each sensor node to obtain our optimization objective. In our proposed work, a DC selects a total horizon of equipped with DCs, which selects the horizon of each specific area with based on its antenna orientation. DC's orientation is scheduled for each time slot. Furthermore, multiple MCs are used to transmit energy for sensor nodes which cannot be covered by DCs. We divided the Rechargeable Wireless Sensor Network into several zones via the Voronoi diagram. We deployed a static DC and one MC charging location in each zone to provide wireless charging service jointly. We obtain the optimal charging location of MCs in each zone by solving Mix Integral Programming for energy transmission. The optimization objective of our proposed research is to sense maximum data from each sensor node with the help of maximum energy. The lifetime of each sensor network can increase, and the end delay can be maximized with joint energy transmission. Extensive simulation results demonstrate that our RWSNs are designed significantly to improve network lifetime over the baseline method.

City zones have become increasingly overcrowded as a result of the extensive population widening ratio and the swift relocation of people from villages. The traffic monitoring process is a major issue in these areas due to the massive traffic flow on the roads. This research proposed a cluster-based improved authentication and communication scheme for an Intelligent Transportation System in Vehicular AdHoc Networks (VANETs). Our primary objective is to optimize resource sharing in vehicular communication. We enhanced the reliability, scalability, and stability of fast-moving VANETs by introducing cluster-based routing schemes for Vehicle-to-Vehicle (V2V) and Vehicle-to-Infrastructure (V2I) communications. We used a third-party certification authority for vehicle authentication to address security and privacy concerns. Our proposed schemes support minimizing the end-to-end (E2E) delay and route request, in addition to reducing link failure. Our schemes’ leading yield includes throughput enhancement, TCP Socket Initialization time minimization, TCP handshake response speedup, and DNS lookup improvement. The schemes are centred on short-range peer-to-peer (P2P) wireless communication in a 400-meter radius cluster. This includes innovative P2P wireless communications on VANET using minimized resources. The proposed schemes deliver a secure authentication mechanism with a securely generated vehicle authentication key provided by a certification authority. Furthermore, we have developed RESTful APIs in vehicular communication for implementation purposes, and also offered and implemented algorithms for resource sharing regarding V2V and V2I communication. Ultimately, we evaluated the performance of our experiments.

Artificial neural networks are highly efficient tools for numerous kinds of tasks, which include forecasting, regression, and recognizing patterns in classification and pattern recognition. An artificial neural network is a model for processing information using essential components called artificial neurons that are inspired by the human brain. Two significant aspects of delayed neural networks dynamic activity are their stability and the synchronization phenomenon. This work presents a bidirectional associative memory (BAM) incommensurate fractional-order delay neural network model. The incommensurate fractional orders are calculated within the stability region through the corresponding eigenvalues and their points of equilibrium. The involved neuron states are synchronized with each other for the calculated incommensurate stable fractional orders. The reduction of the time delay will give more relaxation time for the state variable $w_4(t)$ to be stable as compared to the state variable $w_3(t)$ due to the induction of extra activation functions. The theoretical findings of this research have significance for providing guidance and controlling the dynamic behavior of artificial neural networks.

Type 2 diabetes mellitus (T2DM) is a global health concern driven by factors such as obesity, sedentary behavior, and poor diet. This study uses data from the 2017-18 Bangladesh Demographic and Health Survey (BDHS) to analyze regional and individual predictors of diabetes and predi-abetes. Employing a Bayesian multinomial mixed-effects model, we account for regional varia-bility and individual factors like age, gender, BMI, residence, wealth, education, employment, and hypertension. Our results indicate significant regional differences and associations between de-mographic and health-related factors with diabetes risk. Younger individuals and those with higher BMI are more likely to be diabetic, while hypertension significantly increases diabetes risk. We applied machine learning (ML) models, including logistic regression, decision trees, k-nearest neighbor, linear discriminant analysis, and random forest, to classify diabetic status using these predictors, assessing their accuracy through 10-fold cross-validation. Logistic regression and linear discriminant analysis demonstrated robust performance across various response distributions. Simulation studies further examined the impact of different response distributions on model performance, revealing significant differences in classification accuracies. This approach of esti-mating parameters with a Bayesian model, applying ML for prediction, and conducting simulation studies to explore various scenarios highlights the importance of integrating these methodologies for effective diabetes prediction, providing insights for public health strategies to mitigate T2DM's impact.

Drinking water supplies in the developing world often serve as a biosphere for various organisms. Viral gastroenteritis is a neglected area of research in Pakistan, there is no data for the prevalence of enteric viruses in drinking water of the largest city of Karachi. The present study aimed to provide a survey of the existence of enteric viruses: human adenovirus (HAdV), human enteroviruses (hEV), and genotype A rotavirus (GARV) in tap water. Using a simple PCR approach, we detected 20%, 43%, and 23% of HAdV, hEV, and GARV in tap water respectively. We have also shown an overall quality of tap water at the pumping station and consumer tap. Moreover, we assessed the efficiency of small-scale water treatment methods for the removal of viruses.

Construction 4.0 is witnessing exponential growth in Digital Twin (DT) technology developments and applications, revolutionizing the adoption of Building Information Modelling (BIM) and other emerging technologies used throughout the lifecycle of the built environment. BIM provides technologies, procedures, and data schemas representing building components and systems. At the same time, DT enhances this with real-time data for cyber-physical integration, enabling live asset monitoring and better decision-making. Despite being in the early stages of development, DT applications have rapidly progressed in the AEC sector, resulting in a diverse literature landscape due to the various technologies and parameters involved in fully developing the DT technology. The intricate complexities inherent in digital twin advancements have confused professionals and researchers. This confusion arises from the nuanced distinctions between the two technologies, i.e., BIM and DT, causing a convergence that hinders realizing their potential. To address this confusion and lead to a swift development of DT technology, this study presents a holistic review of the existing research focusing on the critical components responsible for developing DT applications in the construction industry. The study identifies five crucial elements: technologies, maturity levels, data layers, enablers, and functionalities. Additionally, it identifies research gaps and proposes future avenues for streamlined DT developments and applications in the AEC sector. Future researchers and practitioners can target data integrity, integration and transmission, bi-directional interoperability, nontechnical factors, and data security to achieve mature digital twin applications for AEC practices. This study highlights the growing significance of DTs in construction and provides a foundation for further advancements in this field to harness its potential to transform built environment practices.

This article presents the development and validation of a new instrument measuring social, cultural, and behavioral factors influencing exposure to occupational zoonoses in agricultural settings. The Social Ecological Model (SEM) and the Standards for Educational and Psychological Testing were used as guiding frameworks to ensure the instrument's validity. The instrument's content was compiled by combining the results of a scoping literature review and an expert qualitative study. The instrument items were drafted, organized, and underwent a meticulous process of revision and adjustment. It was translated into Spanish and tested in one-to-one cognitive interviews with five volunteer agricultural workers. Exploratory factor analysis was conducted for construct discrimination, and bivariate regression analyses were conducted to explore the association with exposure indicators. Evidence of validity was obtained from four out of five sources of validity evidence according to the AERA/APA’s Standards of Educational and Psychological Testing. The Social Ecology of Occupational Zoonoses (SEOZ) was successfully used to determine social and behavioral factors associated with a higher risk of exposure to occupational zoonoses. Further use of the SEOZ can provide valuable insights into developing effective interventions to improve the health and well-being of agricultural workers.

The fourth industrial revolution has resulted in the digitalization of projects and operations across all sectors. Accordingly, efforts are being made to utilize advanced technologies to improve the energy efficiency of the building sector. This study has reviewed the current application and limitations of cutting-edge technologies in this regard. An overview of the use of the Internet of Things (IoT), artificial intelligence (AI), digital twin (DT), and building information modeling (BIM) for energy efficiency of buildings has been provided. It has been found that the use of Industry 4.0 technologies, during the construction and operational phase of buildings, has a great potential to reduce energy consumption and emissions of the sector. This study may help stakeholders of the built environment to understand the role of industry 4.0 tools for energy efficiency of the sector.

Biogeochemical models estimate soil organic carbon (SOC) sequestration, crop growth, and yield. The DeNitrification and DeComposition (DNDC) model was used to simulate soil SOC dynamics and harvested C-biomass in rice-wheat rotation under organic/inorganic fertilizations with conventional tillage (CT) and reduced tillage (RT). Before calibration, DNDC under-predicted harvestable grain C-biomass of rice by 29.22% to 42.14% and over-simulated grain C-biomass of wheat by 55.01% with equal amounts of NPK and animal manure applied under CT. However, after calibration by adjusting default values of soil/crop parameters, DNDC simulated harvestable grain C-biomass of both crops very close to observed values (only -2.81% to -6.17% less). DNDC also predicted effects of nutrient management practices on grain C-biomass of rice/wheat under CT/RT using d-index (0.76 to 0.96) and the calculated root mean squared error (RMSE of 165.36 to 494.18 kg C ha-1). DNDC simulated SOC trends for rice-wheat using measured values of several statistical indices. Regression analysis between modeled and observed SOC dynamics was significant with R2 ranging from 0.35 to 0.46 (p < 0.01), and intercept ranging from 0.30 to 1.34 (p < 0.65). DNDC demonstrated that combined inorganic and organic fertilization may result in higher C-biomass and more SOC sequestration in rice-wheat systems.

The efficiency of a new composite material of the layered double hydroxide (LDH) of ZnMgAl and rice husk biochar (RHB) for the removal of Cu(II) and Pb(II) ions from synthetic wastewater was investigated in this study. The images of scanning electron microscope showed extremely fine crystalline LDH particles decorated on the rough surface of the RHB while the succesful formation of the composite adsorbent (LDH/RHB) was confirmed by the corresponding energy dispersive X-ray and the Fourier-transform infrared spectroscopy. An equilibrium contact time of 30 and 15 min for Cu2+ and Pb2+, respectively, was proposed for the optimum performance of the batch adsorption process. The dose of the LDH/RHB adsorbent was optimized at 0.4 g yielding maximum adsorption capacities of 117 and 124 mg g-1 for Cu2+ and Pb2+, respectively, with corresponding maximum removal efficiencies of nearly 94% and 99%. The initial meta concentrations was optimized at 50 or 60 mg L-1 corresponding to maximum removal efficiencies or adsorption capacities. For the changing initial metal’s concentration, the removal efficiencies remained unchanged for up to 50 mg L-1 and decreased by about 50% by increasing the initial concentrations from 50 to 100 mg L-1. The adsorption capacities observed a linear increasing trend by increasing the initial concentrations from 5 to 60 mg L-1 and remained unchanged afterward up to 100 mg L-1. A solution pH of 6.0 yielded optimum results with an increasing trend in adsorption capacities and percentage removal by changing the solution pH from 2.0 to 7.0. Based on the best-fit of the pseudo second-order kinetic model to the experimental data, the chemisorption was suggested to be the controlling mechanism of adsorption. The fitting of the Langmuir model suggested a monolayer sorption of Cu2+ and Pb2+ in addition to a heterogeneous adsorption as supported by the fitting of the Temkin isotherm. The application of the Dubinin–Radushkevich isotherm proposed a physical adsorption (mean free energy of adsorption less than 8 kJ mol−1) of both heavy metal ions on the surface of the LDH/RHB adsorbent.

Bifenthrin is a synthetic pyrethroid insecticide. It is used worldwide against different agricultural pests. Nervous system (NS) is the primary target organ for the pyrethroid group of insecticide which causes hyper excitation. The aim of this study to determine the effects of bifenthrin on the brain of rabbits. The animals were treated for 14 days with three different doses (1/5th, 1/10th and 1/15th of LD50) of bifenthrin. Neurotransmitters and Histopathological alterations were observed at the end of the experiments. Neurochemical parameters were checked 24 hours after the last dose. Significant changes in the level of biogenic amines were observed. The levels of epinephrine (EPN), dopamine (DA), 3, 4 dihydroxyphenylacetic acid (DOPAC) were decreased as compared to controls group with the increase in insecticide. However, norepinephrine (NE) and homovanillic acid (HVA) levels were found to be significantly higher than those of the controls. A significant reduction in the activity of the acetyl cholinesterase enzyme was found in the frontal cortex’s erythrocyte, plasma and brain of rabbit with the increase in administered bifenthrin. The oxidative stress showed significantly decrease in the activity of glutathione peroxidase (GPx), superoxide dismutase (SOD), catalase (CAT) and glutathione S- transferase (GST) with the increase in dose of bifenthrin. Histopathological study of brain tissues showed normal GC (glial cells) and NC (neuronal cells) in the frontal cortex of brain tissue of control groups while the treated groups showed evacuation (odema), elongation of pyramidal nucleus, glial cell damage and brain haemorrhage.

The comfort of human life depends on the quality, size, and reliability of the infrastructure projects. In the infrastructure systems, rapid growth is found, where the economic and sustainable impact has become a topic of significant concern for policies and government officials. To achieve con-straints of sustainable development, all the policies and actions over the infrastructure project's life cycle must be assessed. Decision-makers have adopted approaches for economic, social, and en-vironmental initiatives through Life Cycle Assessment (LCA) and Life Cycle Cost Analyses (LCCA) of infrastructure projects. The purpose of this review is to highlight the impact of per-forming LCA and LCCA in infrastructure projects. To achieve this goal, a systematic literature review methodology is adopted in which renowned databases, i.e., Web of Science, Science Direct, Emerald and Scopus were selected to extract the relevant literature. Using the PRISMA approach, 1251 publications were identified which were then filtered and 55 documents were included in the final review. In the extracted publications most, researchers were biased toward LCA and LCA individually, whereas few focused on integrated LCA and LCCA. The researchers assessed the costs and impact associated with the infrastructure project while there were less focused on the environmental cost. Besides this, techniques of economic, social, and environmental growth of infrastructure projects have been emphasized during the design phase because of substantial relations between infrastructure design and operation management. Moreover, a conceptual framework has been developed that will assist the decision-makers to consider the effects of LCA and LCCA on various aspects of the infrastructure project and how it impacts sustainability. In the last, a case study was performed to assess the developed framework with the incorporation of environmental impact cost.

As urban populations and transport demand expand, Pakistani metropolitan centers face traffic congestion and environmental challenges. This research aims to assess carpooling (CP) to alleviate traffic congestion, fuel demand, and pollution. This study was conducted in Islamabad, a fast-growing city with a high percentage of personal cars in Pakistan, to assess the travelers’ perceptions, and public acceptance of CP and determine the effects on traffic congestion, fuel consumption, and CO2 emissions. The investigation of travelers' perceptions towards CP was conducted through a stated preference questionnaire survey. A total of 700 responses from one million population of Islamabad were collected as per Sloven's Formula. SPSS and Smart PLS software were used for data analysis. Various factors influencing peoples’ travel perceptions, mode choice, and tendency to carpool, were categorized to evaluate the relationship between travelers’ perception and the tendency to carpool in the presence of mode choice as a mediating variable. Confirmatory factor analysis was conducted in SMART PLS to refine the number of scale items for each variable. One-way ANOVA, step-wise and mediated multiple regression analysis was conducted in SPSS to check the direct and mediating relationship between different variables. Moreover, the probability of reducing traffic congestion and assessing fuel reduction resulting from CP was also analyzed. The findings imply that travelers’ mode choice acts as a mediator between the relationship between travelers’ perception and tendency to carpool. Furthermore, results predicted that CP might reduce 0.25 million cars on the road, about 33.6% of the total private vehicles. Thereby, saving up to 546,810 barrels per year, about 3.42% of Pakistan's total petrol consumption. The findings of this study could be helpful for transport planners, environmentalists, and policymakers to implement carpool systems. Thus, reducing traffic congestion and harmful CO2 emissions and maintaining a sustainable environment.

Blockchain innovation stands out enough to be noticed and adopted in various countries and organizations around the world. Many businesses, including finance, medical services, inventory networks, security, libraries, and the internet of things, are currently under attack. For the benefit of the blockchain, many businesses incorporate blockchain technology into their frameworks. Despite its solidarity, blockchain faces a few challenges in security, protection, adaptability, and other areas. This paper examines the forward leap in blockchain innovation, as well as its applications and challenges. While many blockchain papers focus on digital currencies, IoT, and security, this paper focuses on the overall best in a class of blockchain innovation, its new twists and turns, and choices, particularly in areas other than cryptographic forms of money. The investigators' goal is to provide a thorough audit of the cryptography underlying blockchain to better understand the innovation. The examiners also conduct general research on people and venture blockchains, as well as future exploration opportunities and their implications for blockchain innovation.

Gas sensing is crucial for detecting hazardous gases in industrial environments, ensuring safety and preventing accidents. Additionally, it plays a vital role in environmental monitoring and control, helping to mitigate pollution and protect public health. Integrated photonic gas sensors are important due to their high sensitivity, rapid response time, and compact size, enabling precise recognition of gas concentrations in real-time. These sensors leverage photonic technologies, such as waveguides and resonators, to enhance performance over traditional gas sensors. Advancements in materials and fabrication techniques could further improve their efficiency, making them invaluable for environmental monitoring, industrial safety, and healthcare diagnostics. In this review, we delved into photonic gas sensors that operate based on the principles of evanescent field absorption (EFA) and wavelength interrogation methods. These advanced sensing mechanisms allow for highly sensitive and selective gas detection, leveraging the interplay of light with gas molecules to produce precise measurements.

Few switching transitions in high power and medium voltage application of Power converters are desirable. The selective harmonics elimination (SHE) pulse width modulation offers a better quality waveform with lower switching transitions and hence lower switching losses. The SHE is a pre-programmed modulation technique where certain amounts of lower order harmonics are removed and fundamental voltage is controlled. After Fourier analysis of output waveform, a set of nonlinear transcendental equations is obtained which exhibits, multiple, unique or no solution in different range of modulation index (MI). In this paper, an iterative method based on the Jacobian estimate is proposed to solve a highly non-linear set of SHE equations. The proposed technique is easy in implementation and can solve a large number of such equations as computation of the Jacobian matrix in the subsequent iteration is estimated from the previous values. Moreover, the proposed method also removes the singularity problem, especially for large SHE equations. High accuracy in the initial guess is also not essential for this method and can converge to the solution with any random initial guess. The computational and simulation results are given to validate the concept. The hardware result is provided to confirm the computational and simulation results.

The Atlantic puffin is a medium-sized seabird with black and white plumage and orange feet. It is distributed mainly along the northern Atlantic Ocean and due, among other reasons, to human activities, it is in a threatened situation and classified as a vulnerable species according to the International Union of Conservation of Nature (IUCN). In this study, we used a total of 20 carcasses of juvenile Atlantic puffins to perform anatomical cross sections and magnetic resonance images. Thus, an adequate description of the head was made, providing valuable information that could be helpful as a diagnostic tool for veterinary clinicians, who increasingly treat these birds in zoos, rehabilitation centers and even in the wild.

There are many pollution and environment problem in the human ecosystem. There are different methods are used to removal of sulfur from sour gases for example Basic Claus process and Modified Claus process . There are different chemical software are used for simulation and optimization of Claus process for example Aspen Plus and Chemcad ECT. The Gibbs free energy method is introduced and model of Claus process. There are new parameter are introduced in reaction furnace to reduce the error from 33% to 7 %. The waste heat boiler is installed at the reaction furnace in which high pressure stream is produced and study the decomposition the hydrogen sulphide. The new rate of reaction is introduced of the enhancement of H2 production in chemical process. The simulation of reaction furnace in Aspen plus software is the maximum utilization of process. Due to suitable operating condition of reaction furnace is caused the maximum destruction of ammonia gas in the reactor. When we are increasing the oxygen concentration and temperature of feed is causing decreasing the ammonia production in reaction furnace. It is below than acceptance value of ammonia is 150 ppm in the reaction furnace. The presence of oxygen components, Sulfur oxide, hydroxide components are effect on decreasing the amount of ammonia in furnace and temperature is about at 1350⁰C. It is noted that when the production of sulfur recovery is decrease in Claus process and the production of carbon monoxide is increase in the thermal section at the existence. Now we are work on parametric studies of furnace that could be causes the production of ammonia destruction and CO emission in the Claus process. Due to optimize the reaction furnace parameter are help to get large of sulfur production, ammonia gas destruction, increased the catalyst life and decreased of dangerous gases.

Oil spillage over a sea or ocean’s surface is a threat to marine and coastal ecosystems. Spaceborne synthetic aperture radar (SAR) data has been used efficiently for the detection of oil spills due to its operational capability in all-day all-weather conditions. The problem is often modeled as a semantic segmentation task. The images need to be segmented into multiple regions of interest such as sea surface, oil spill, look-alikes, ships and land. Training of a classifier for this task is particularly challenging since there is an inherent class imbalance. In this work, we train a convolutional neural network (CNN) with multiple feature extractors for pixel-wise classification; and introduce to use a new loss function, namely ‘gradient profile’ (GP) loss, which is in fact the constituent of the more generic Spatial Profile loss proposed for image translation problems. For the purpose of training, testing and performance evaluation, we use a publicly available dataset with selected oil spill events verified by the European Maritime Safety Agency (EMSA). The results obtained show that the proposed CNN trained with a combination of GP, Jaccard and focal loss functions can detect oil spills with an intersection over union (IoU) value of 63.95%. The IoU value for sea surface, look-alikes, ships and land class is 96.00%, 60.87%, 74.61% and 96.80%, respectively. The mean intersection over union (mIoU) value for all the classes is 78.45%, which accounts for a 13% improvement over the state of the art for this dataset. Moreover, we provide extensive ablation on different Convolutional Neural Networks (CNNs) and Vision Transformers (ViTs) based hybrid models to demonstrate the effectiveness of adding GP loss as an additional loss function for training. Results show that GP loss significantly improves the mIoU and F1 scores for CNNs as well as ViTs based hybrid models. GP loss turns out to be a promising loss function in the context of deep learning with SAR images.

This study investigated the ability of a HYDRUS 1D model for predicting the vertical distribution of potassium iodine (200 ppm) in soil columns after amendment with five different common remediation materials (gypsum, lime, fly ash, charcoal and sawdust) at a rate of 2.5% (w/w), relative to an unamended control soil. Results shows that relative to the unamended soil, iodine leaching was decreased by all amendments but that the magnitude of the decreases varied with the soil amendment applied. Iodine content was highest in the upper layer of the soil columns and decreased progressively with soil depth. The model was evaluated via comparison of the model simulated values with measured values from the soil column studies. The results showed that the HYDRUS 1D model efficiency was near to 1, indicating that the stimulated results were near to the measured values. Therefore, this study showed that iodine leaching through a soil could be ascertained well using a HYDRUS 1D model. The model over predicted iodine leaching, resulting to a weak correspondence between the simulated and the measured results for iodine leaching. This suggests that the HYDRUS-1D model does not explain accurately different organic and inorganic amended soil and the preferential flow that occurs in these columns. This may be due to the fact that Freundlich isotherm, which is part of the transport equations, does not sufficiently describe the mechanism of iodine adsorption onto the soil particles. This study would help to select amendments for an effective management strategy to reduce exogenous iodine losses from agro-ecosystems. This would also improve understanding of iodine transport in soil profile.

Spontaneous parametric downconversion At the heart of all quantum optics experiments is called as Spontaneous parametric downconversion. This is a downconversion process when the output frequency is smaller than the input frequency. The whole process is Spontaneous. Experimentally we have to downconvert the photons and convert them into pairs of a photon. We use the Beta-barium borate(BBO) crystals to downconvert the coming violet-blue laser. We find the maximum number of counts on detectors and their coincidence. When the BBO crystals is well aligned, we find no difference in detecting vertically or horizontally polarized photons because they are orthogonal to each other. Proof of existence of photons We want to investigate the properties and verification of quantization of light. Experimently we want to establish the existence of single photon which shows the grainy-ness of individual photon quantum mechanically and shows wave like behaviour classically. We get the coincidences counts on detectors with addition of detector B’ by using PBS in the path of signal beam. Experimentally we prove the Quantum as well as classical nature of light by the measurement of second-order degree coherence in light g²(0). For classically the g²(0)≥1 and quantum mechanically g²(0)=0.When we add the delay time interval of 1ns after reflected and transmitted photons from PBS signal beam. The delay generator did not create a significant difference in the coincidence counts detection in the value of g²(τ ). Single photon interference and quantum eraser we want to observe the interference by making the single photons pass through the interferometer, and we will see the interference of the single photons. If the light passes through the interferometer, the visibility of the interference pattern to which extent these fringes are observed is dependent on the extent to which the ’which-way’ or ’which-path’ information is available to the experimenter. If the observer knows the information about the ’which-way’ of the light path, then we cannot observe the inference pattern. Because we only can make an interference pattern if we erase the which-way information of the light path. If you erase the information about the’ which-way,’ we can observe a very high interference pattern. We can erase the information about the light path’s ’which-way’ or ’which-path’ by using a polarizer and orienting at 45^o. In this way, we can observe a very high pattern. If we introduce the angle of the polarizer at 0^o or 90^o, we see very low interference.

The gut microbiome offers numerous advantages to the hosts, through a variety of physiological mechanisms like firming up gut integrity or shaping the intestinal epithelium. Studies showed 2172 species are identified and isolated from human beings, ordered into twelve different phyla, of which 93.5% belonged to Bacteroidetes, Firmicutes, Proteobacteria and Actinobacteria. Out of the 12, three phyla are identified. Human microbial communities are affected by the host external factors like dietary patterns, lifestyle factors, antibiotic usage, internal factors gender, host genotype, age and race. To analyze the dysbiosis and bacterial variation in different areas of District Faisalabad 10,000 individuals of age 25–35 years were recruited from the two different rural and urban localities. The oral swab and fecal sample were collected according to prescribed manner. The collected samples from demographically and geographically distinct regions of District Faisalabad were subjected to DNA extraction and quantification. The amplification of 16s rRNA was carried out by PCR and visualized through a transilluminator. The results revealed significant elevated, % abundance of fecal microbial profile Blautia spp, Firmicutes, Ruminococcaceae, in rural population however non-significant difference % abundance of total Bifido, E. coli, Faecali bacteria, total Lactobacillus were identified in both demographically distinct regions. The pathogenic Gamma Protebacteria, Fusobacterium, Campylobacter coli were not detected in both study areas. Out of five orally detected microbial profiles, elevated % abundance of Firmicutes was detected in rural population however non-significant difference was observed in % abundance of total Bifido and E. coli in both populations. Total Lactobacillus and Fusobacterium were not detected in oral sample of both urban and rural population. Conclusively, this research accomplished the potential effects of demographic and geographical induced dysbiosis in the normal microbiome of the oral cavity and intestine that might cause dysbiosis associated disorders.

The oviparous blow fly Calliphora vicina has shown potential as a managed pollination species to support honeybee (Apis mellifera) usage in Australian horticulture. This blow fly species lays eggs onto carrion soon after death and the resultant larvae that hatch are necrophagous and feed on the decomposing tissues of the dead animal. Newly hatched larvae of this fly were provided with plant-based meals (soya bean and canola) and compared with animal-derived meatmeal to determine if plant-based meal could be used to mass rear this blow fly species. Both soyabean and canola meal media did not support the survival of any larvae through to adult eclosion. The addition of only 10% whole egg powder to the plant-based meals enabled survival to eclosion of 39% and 13% on soyabean and canola based medias respectively compared with 76% on animal-based meatmeal with 10% whole egg powder. Larvae fed livestock meatmeal with 10% whole dried egg powder had the fastest development to the pupal stage, the highest pupation rate, the heaviest pupae and the highest subsequent adult eclosion. This study concluded that the use of plant-based meals in the mass rearing of the blow fly C. vicina was neither viable, nor economically viable.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

During December 2019, a novel coronavirus named SARS-CoV-2 has emerged in Wuhan, China. The human to human transmission of this virus has also been established. The virus has so far infected more than 2 million people and spread over 200 countries. The World Health Organization (WHO) has declared COVID-19 a global health emergency due to its spread well beyond China. It has been established that this virus originates from bats and uses an intermediate host for transfer to humans. The knowledge about the intermediate host is important to find the virus shuttle mechanism to stop future outbreaks. For this, the genetic and structural analysis of coronaviruses spike proteins was performed using a computer-assisted approach.To conduct the In silico analysis, 43 sequences of spike protein belong to different species were retrieved from the NCBI nucleotide database. Pairwise and multiple sequence alignments were performed to check the similarities and differences of the retrieved sequences. Moreover, to highlight relationships among different species, phylogenetics analysis was performed using the MEGA software tool. In the end, protein structure alignment (superimposition) was performed against the reference structure by UCSF Chimera software. The results highlighted that the maximum similarity of human protein was found against Bat and Pangolinsequences. Moreover, among Bat and Pangolin, the highest similarity was found against pangolin based on phylogenetics analysis. These results suggest that SARS-CoV-2 transfers from bats to humans through pangolins.

Wheat (Triticum aestivum L.) being a staple food crop is an important nutritional source providing protein and minerals. It is important to fortify staple cereals like wheat with essential minerals to overcome the problems associated with malnutrition. The experiment was designed to evaluate the status of 11 micronutrients including grain iron (GFe) and zinc (GZn) in 62 wheat cultivars released between 1911 and 2016 in Pakistan. Field trials were conducted over two years and GFe and GZn were quantified by both inductively coupled plasma optical emission spectroscopy (ICP-OES) and energy dispersive X-ray fluorescence spectrophotometer (EDXRF). The GZn ranged from 18.4 to 40.8 mg/kg by ED-XRF and 23.7 to 38.8 mg/kg by ICP-OES. Similarly, GFe ranged from 24.8 to 44.1 mg/kg by ICP-OES and 26.8 to 36.6 mg/kg by EDEXR. The coefficient of correlation was higher for GZn (r=0.90), compared to GFe (r=0.68). Modern cultivars like Zincol-16 and AAS-2011 showed higher GFe and GZn along with improved yield components. Old wheat cultivars WL-711, C-518 and Pothowar-70 released before 1970 also exhibited higher value of GFe and GZn, however their agronomic performance was poor. Multivariate analysis using ten micronutrients (Al, Ca, Cu, K, Mg, Mn, Na and P) along with agronomic traits, and genome-wide SNP markers identified the potential cultivar with improved yield, biofortification trait and wider genetic diversity. Genetic gain analysis identified significant increase in grain yield (0.4% year-1), while there was negative gain for GFe (-0.11% year-1) and GZn (-0.15% year-1) over the span of 100 years. The Green Revolution Rht-B1 and Rht-D1 genes had strong association with plant height, and grain yield (GY), while semi-dwarfing alleles had negative effect on GFe and GZn contents. This study provided a valuable insight into biofortification status of wheat cultivars deployed historically in Pakistan and is a valuable source to initiate a breeding strategy for simultaneous improvement in wheat phenology and biofortification.

Hearing impairment is an immensely diagnosed genetic cause, 5% of the total world population effects with different kind of congenital hearing loss (HL). In third-world countries or countries where consanguineous marriages are more common the frequency rate of genetic disorders are at its zenith. Approximately, the incidence of hearing afflictions is ostensibly 7-8:1000 individuals whereas it is estimated that about 466 million peoples suffer with significant HL, and of theses deaf cases 34 million are children’s up to March, 2020. Several genes and colossal numbers of pathogenic variants cause hearing impairment, which aided in next-generation with recessive, dominant or X-linked inheritance traits. This review highlights on syndromic and non-syndromic HL (SHL and NSHL), and categorized as conductive, sensorineural and mixed HL, which having autosomal dominant and recessive, and X-linked or mitochondrial mode of inheritance. Many hundred genes involved in HL are reported, and their mutation spectrum becomes very wide. Mapping of pathogenic genes in consanguinity family is facilitated to understand the disease history. Review presents the bases of HL and also focused on various genetic factors that cause deafness like the basics of genetic inheritance, and classic and well-characterized inherited factors of it. It also overviews the application of linkage analysis, SNPs genotyping and whole exome sequencing methods, in mapping and identification of new locus, causative genes and their variants in families inherited with HL. Conclusively, this review supports researchers in understanding the location of chromosome, the causative genes and specific locus which causing deafness in humans.

Climate change is impacting the spread/intensity of vector-borne diseases, including malaria, and accelerating evolutionary/adaptive changes in vector species. These changes including chromoso-mal inversions and overexpression and/or changes in allele frequencies of thermotoler-ance-associated genes, may facilitate insecticide resistance through pleiotropy. This study investi-gated the impact of thermotolerance on pyrethroid resistance in four populations of malaria vector An. gambiae, from savanna/sub-Sahel of northern Nigeria. Anopheles coluzzii and An. gambiae were the only malaria vectors found, sympatric in all the sites, with the former species predominant. High thermotolerance was observed, with no mortality at 38°C, and LT50 of ~44°C. Significantly high permethrin resistance was observed (mortality <50%) in heat-hardened (44°C) larvae from two sites, BUK and Pantami, compared with control, and heat-hardened adult females from Auyo (mortality = 3.00%±1.20, χ2 = 5.83, p<0.01) compared with control (12.00%±4.65). The 2La chromosomal inver-sion was detected at ~50% in larvae and 58% in adult females. Significant association was observed (OR = 7.2, p<0.03) between permethrin resistance and 2La/+a rearrangement compared with 2L+a/+a, in BUK larvae. For all sites permethrin resistance correlated with 2La/a homozygosity in adult fe-males [OR = 5.02, p=0.01). qRT-PCR identified 6 genes commonly induced/overexpressed, including heat shock protein 70 (AGAP004581) which was 2468x and 5x overexpressed in heat-hardened and permethrin-resistant females, respectively, trehalose-6-phosphate synthase (AGAP008227), and ionotropic glutamate receptor genes, IR25a (AGAP010272) and IR21a (AGAP008511). This study highlights challenges associated with insecticide-based malaria vector control, and the epidemiological significance of taking climate variables into account for design/choice of control measures.

This article is a continuity of prevouse two reserch in daylight harvastion control that were deigned using classical control apoproach and then fuzzy logic technique, In this article ANN controller is designed and its response is compared with the performance of the other two controllers. Detailed compression for the different error type is illustrated, however, the results show that the three controller operate with satisfactory accuracy.